PowerTRONIC Installation Manual -

Royal Enfield Himalayan 2021 without choke

Document Version 1 Release Date 10 October 2021

Application information Vehicle Specific

Vehicle Royal Enfield

Model Himalayan EFI

Year of manufacture 2021 without choke

PowerTRONIC application All PowerTRONIC ECUs, from firmware version F.3.x onwards

Note:

● Read through all instructions before installation and use.

● Ensure that the bike is switched off and the key is out of the ignition before proceeding with the
installation.
● Some parts of the bikes might be hot/sharp and may cause burns/cuts. Proceed with extreme
caution or wait until the bike has cooled down. Always wear safety gloves.
● When the installation is complete, make sure to secure the wiring loom away from the movable parts
or components which tends to heat up during the normal operation of the vehicle at any chance.
● PowerTRONIC is intended for motorsport use on a closed course, please check with your local laws
before using this product. Race Dynamics / PowerTRONIC is not liable for consequences arising out
of using the product.

Call/Whatsapp: +919916229292 / +918040929292

E-Mail: [email protected]
Official Website: www.powertronicECU.com
Social: www.facebook.com/PowertronicECU/
www.instagram.com/powertronic_ecu/
1
Table of Contents
1. Parts list
2. Tools required
3. Installation procedure
3.1 Removing panels, fairing etc
3.2 Routing the harness
3.3 Fuel Injector Connector
3.4 Ignition Coil Connector
3.5 Ground Terminal
3.6 Changing Relays
3.7 Modulators
3.8 Securing the routed harness
3.9 Testing with Stock Coupler
3.10 Plugging in the PowerTRONIC
3.11 Attaching the panels, fairing etc

1. Parts list
1 PowerTRONIC Piggyback ECU
2 Stock Coupler Stand by unit
● Can be connected in place of the PowerTRONIC to run the bike in stock
mode if need be.
● Used for the verification of the connections.

3 Harness Bike specific harness contains the following connectors

● Fuel injector connector - INJ
● Spark/Ignition coil connector - SPK
● Modulators
● Map selection connector
● Quickshifter connector
● Ground terminal - GND
4 USB cable Can be used to connect the PowerTRONIC to a laptop for throttle calibration or
changing maps
5 Nylon Tags To secure wiring harness
6 User guide and Warranty card Instructions

2. Tools required
Serial No Main tools Optional tools
1 M10 Hexagonal socket Spinner handle
2 M10 T bar Hexagonal Socket wrench Ratchet handle
3 Wire cutter Extension bar or Sliding T bar

2
3. Installation procedure
3.1 Removing panels, fairing
Begin at the left side of the bike.
Park the bike using the centre stand on a level surface (Or a paddock stand).

3
3.1.1 Detach the pillion seat by inserting the key into the keyhole shown in Image 1 and unlock the pillion seat. Image 2
shows the pillion seat detached.

Image 1

Image 2

4
3.1.2 Detach the rider seat. (Gently lift and slide it towards the rear end) - Refer Image 3.

Image 3

3.1.3 Image 4 shows both the seats detached.

Image 4

5
3.1.4 Unscrew the tank bolts using the T socket M10 T bar Hexagonal socket wrench. Refer Image 5.

Image 5

3.1.5 Gently give a little lift to the tank and locate fuel gauge connector (Blue colour) on the left side of the tank. Refer
Image 6.

Image 6

6
3.1.6 Detach the fuel gauge coupler. Refer Image 7.

Image 7

3.1.7 Go to the right side of the bike, Locate the fuel line under the fuel tank, after the fuel valve. Gently squeeze and pull
the fuel pipe to detach it from the valve. (There may be some amount of gasoline in the pipe. Make sure it does not fall on
your body or clothes). Refer Image 8.

Image 8

7
3.1.8 Right next to the fuel valve, locate the fuel pump connector and detach the connector carefully. Refer Image 9.

Image 9

3.1.9 Lift the tank carefully and locate the two vacuum hoses present (and connected) under the tank. Disconnect both
the hoses and lift away the fuel tank and place it safely. Refer Image 10

Image 10

8
3.1.10 Refer Image 11 for disconnected view of the vacuum hoses.

Image 11

3.1.11 Unscrew the bolts using M10 Hex T-bar from the casing as shown through Image 12 and Image 13 below.

Note: Use a spinner handle with M10 Hex socket and hold the nut below for easy removal.

Image 12

9
 Image 13

3.1.12 Remove both the screws using M10 Hex T-bar from the mud guard (adjacent to tail indicators) shown through
Image 14.

Image 14

10
3.1.13 Once you unscrew the bolts, there will be enough space to route the wiring harness of the PowerTRONIC. Refer
Image 15.

Image 15

3.1.14 Remove the screws using M10 Hex T-bar from the casing as shown in Image 16 below.

Image 16

11
 3.2 Routing the harness
3.2.1 Starting from the glove compartment, route each connector terminals from in-between the welded plate and the
mud guard. Refer Image 17.

Image 17

3.2.2 Apply slight pressure, if needed, (refer Image 18 ) on the mudguard for easy routing.

Image 18

12
3.2.3 Once all the connectors are through, secure the harness along the bike’s frame as shown in Images 19 & 20.

Image 19

Image 20

13
 3.3 Fuel Injector Connector (Left side of the bike)
3.3.1 Locate the stock injector connector of your bike. Refer the Images 21 and Image 22 below

Image 21

Image 22

14
3.3.2 Identify the fuel injector connector in the PowerTRONIC wiring harness. The connectors are labeled 'INJ'.

3.3.3 Disconnect the injector connector on your bike. Refer the zoomed view (Image 23).

Image 23

3.3.4 Connect the female PowerTRONIC injector connector to the stock male injector connector. Refer Image 24.

Image 24

15
3.3.5 Connect the stock female injector connector to the PowerTRONIC male injector connector. Refer Image 25.

Image 25

16
 3.4 Ignition Coil Connector (Left side of the bike)
3.4.1 Locate the stock Spark/Ignition coil connector on the ignition coil, located right above the engine. Refer Images 26
and 27.

Image 26

Image 27

17
3.4.2 Identify the Spark/Ignition coil connector in the PowerTRONIC wiring harness. The connectors are labelled 'SPK'
Refer Image 28.

Image 28

3.4.3 Detach the stock ignition coil connectors. Refer Image 29.

Image 29

18
3.4.4 Connect the PowerTRONIC Ignition coil male connector to the stock ignition coil female connector. Refer Image 30.

Image 30

3.4.5 Connect the PowerTRONIC Ignition coil female connector to the stock ignition coil male connector. Refer Image 31
below.

Image 31

19
3.4.6 Refer Image 32 for completed view.

Image 32

20
 3.5 Ground Terminal Connector (Right side of the bike)
3.5.1 Identify the Ground terminal connector labeled as GND and connect it to the negative terminal of the battery.
Refer the Images 33 and 34.

Image 33

Image 34

21
 3.6 Changing Relays
3.6.1 Locate the stock relays Image 35.

Image 35

3.6.2 Remove the stock relays from the relay kit. Refer Image36.

Image 36

22
3.6.3 Replace the stock relays with provided relays. Refer Image 37.

Image 37

3.6.4 For 2021 models, replace the stock relay marked in the image with the provided relay. Refer Image 38.

Image 38

23
3.6.5 Observe the position of the relay and replace it accordingly. Refer Image 39.

Image 39

24
 3.7 Ignition modulators connector
3.7.1 Locate the fuse box and Push the fuse box to the front to remove it accordingly. Refer Image 40 & 41

Image 40

Image 41

25
3.7.2 Place both the Ignition modulator and slide it in the gap created by removing the fuse box. Refer Image 42

Image 42

3.7.3 Connect the Ignition modulators to the PowerTRONIC harness and route it accordingly. Refer Image 43

Image 43

26
 3.8 Securing the harness using ties
3.8.1 Secure the harness away from hot/moving parts by attaching it to the chassis/frame using the zip ties provided
wherever necessary. Refer to Image 44.

Image 44

Important note: The PowerTRONIC harness contains a Quick shifter connector. If you have bought the Quickshifter please
attach the connector to it. [Please refer Quick shifter installation manual]

If you have not bought the Quickshifter, you can leave it disconnected but make sure the harness is secured using zip ties
provided.

27
 3.9 Testing with the stock coupler
3.9.1 Attach the fuel tank.

3.9.2 You can verify the connections by attaching the stock coupler. Refer Image 45 Refer to the detailed Stock coupler
test document.

Image 45

DO NOT proceed with the PowerTRONIC ECU without first verifying the connections with the stock
coupler.

28
 3.10 Plugging in the PowerTRONIC
Remove the key from the ignition, unplug the stock coupler and connect the PowerTRONIC to the harness by connecting it
to the 32 pin connector. Secure it in the glove box. Refer Image 46.

Image 46

3.11Attaching the panels fairing etc

Attach the panels, fairing as removed from the bike.

29