CHEMISTRY INVESTIGATORY PROJECT of Class XII

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 18

CHEMISTRY

INVESTIGATORY
PROJECT
REPORT

DETERMINING
AMOUNT OF
ACETIC ACID IN
VINEGAR

Name: Shivam Panchal


Std : XII
Div: A
School: Kendriya Vidyalaya Bhilwara
:: CERTIFICATE ::

This is to certify that M r


Shivam Panchal
of class XII has
completed the chemistry project entitled
‘DETERMINATION OF AMOUNT OF
ACETIC
ACI D IN VINEGAR’
herself and under my guidance during the
academic year 2021-22
The progress of the project has been
continuously
reported and has been in my knowledge
consistently .

Teacher Incharge Head of Instituition


:: AIM ::

Measuring the Amount of Acetic


Acid In Vinegar
by Titration with an Indicator solution.
::ACKNOWLEDGEMENT::

I sincerely thank our Chemistry teacher Mrs Pooja Yadav for


her guidance, encouragement and support throughout the
duration of the project. Without her motivation and help the
successful completion of this project would not have been
possible.

I would also like to extend ma gratitude to the entire


Chemistry department of Kendriya Vidyalaya Bhilwara for their
constant support.

Shivam Panchal
XII A
:: Index ::
1. Certificate
2. Aim
3. Acknowledgement
4. Objective
5. Introduction
6. Apparatus
7. Theory
8. Experimental Procedure
9. Experiment 1
10. Experiment 2
11. Experiment 3
12. Result
13. Precautions
14. Bibliography
:: OBJECTIVE ::

The goal of this project


is to determine the amount of Acetic Acid
in different types of vinegar
using titration with a
coloured pH indicator to
determine
the endpoint.
:: INTRODUCTION ::

About Vinegar:
Vinegar is a solution made from the fermentation of ethanol
(CH3CH2O H ) , which in turn was previously fermented from
sugar. The fermentation of ethanol results in the production of
acetic acid (CH3COOH). There are many different types of
vinegar, each starting from a different original sugar source
( e.g., rice, wine, malt, etc.) . The amount of acetic acid in
vinegar can vary, typically between 4 to 6% for table vinegar,
but up to three times higher ( 18%) for pickling vinegar .

Titration introduction:
In this project, I have determined the amount of acid in
different vinegars using titration, a common technique in
chemistry. Titration is a way to measure the unknown amount of
a chemical in a solution (the titrant) by adding a measured
amount of a chemical with a known concentration (the titrating
solution). The titrating solution reacts with the titrant, and the
endpoint of the reaction is monitored in some way. The
concentration of the titrant can now be calculated from the
amount of titrating solution added, and the ratio of the two
chemicals in the chemical equation for the reaction.

Titration theory:
To measure the acidity of a vinegar solution, we can add
enough hydroxyl ions to balance out the added hydrogen ions
from the acid. The hydroxyl ions will react with the hydrogen
ions to
produce water. In order for a titration to work, we need three
things:
1. a titration solution (contains hydroxyl ions with a
precisely known concentration),
2. a method for delivering a precisely measured volume of
the titrating solution, and
3. a means of indicating when the endpoint has been reached.
For the titrating solution, we'll use a dilute solution of
sodium hydroxide (NaOH). Sodium hydroxide is a strong
base, which means that it dissociates almost completely in
water . So for every NaOH molecule that we add to the
solution,we can expect to produce a hydroxyl ion.

Performing titration:
To dispense an accurately measured volume of the titrating
solution, we will use a burette. A burette is a long tube with a
valve at the bottom and graduated markings on the outside to
measure the volume contained in the burette. The burette is
mounted on a ring stand, directly above the titrant solution .
Solutions in the burette tend to creep up the sides of the glass
at the surface of the liquid. This is due to the surface tension
of water. The surface of the liquid thus forms a curve, called a
meniscus. To measure the volume of the liquid in the burette,
always read from the bottom of the meniscus.

Indicators:
In this experiment, we will use an indicator solution called
phenolphthalein. Phenolphthalein is colourless when the solution
is acidic or neutral. When the solution becomes slightly basic,
phenolphthalein turns pinkish, and then light purple as the
solution becomes more basic. So when the vinegar solution
starts to turn pink, we know that the titration is complete.
:: APPARATUS ::

To do this experiment we will need the following materials and


equipment:
➔ Vinegar, three different types.
➔ Distilled water
➔ Small funnel
➔ 0.5% Phenolphthalein solution in alcohol (pH
indicator solution)
➔ 0.1 M sodium hydroxide solution
➔ 125 mL Conical flask
➔ 25 or 50 mL burette
➔ 10 mL graduated cylinder
➔ Ring stand
➔ Burette clamp
:: THEORY ::
Required amount of sodium hydroxide (NaOH) can be calculated
using the following formula:
Molarity X Molar Mass X Volume (cm )
3

W=
1000
Molar mass of NaOH = 40 g/mol
0.5 X 40 X 500
=
1000
= 10 g

The acetic acid content of a vinegar may be determined by


titrating a vinegar sample with a solution of sodium hydroxide
of known molar concentration (molarity).
CH3COOH(aq) + NaOH(aq) --> CH3COONa(aq) + H2O(l)
(acid) + (base) --> (salt) + (water)
At the end point in the titration stoichiometry between the
both solution lies in a 1:1 ratio.
M COOH X VCH COOH
= M NaOH X V NaOH
3 3

CH

Strength of acid in vinegar can be determined by the following


formula:
Strength of acetic acid = M CH COOH X 60 3

Indicator:- Phenolphthalein
End Point:- Colourless to pink
:: EXPERIMENTAL
PROCEDURE ::
1. Pour 1.5 ml of vinegar in an Conical flask.
2. Add distilled water to dissolve the vinegar so that
the volume of the solution becomes 20 mL.
3. Add 3 drops of 0.5% phenolphthalein solution.
4. Use the burette clamp to attach the burette to the ring
stand. The opening at the bottom of the burette should be
just above the height of the Conical flask we use for the
vinegar and phenolphthalein solution.
5. Use a funnel to fill the burette with a 0.1 M solution
of sodium hydroxide.
6. Note the starting level of the sodium hydroxide solution in
the burette. Put the vinegar solution to be titrated under
the burette.
7. Slowly drip the solution of sodium hydroxide into the
vinegar solution. Swirl the flask gently to mix the solution,
while keeping the opening underneath the burette.
8. At some point we will see a pink colour in the vinegar
solution when the sodium hydroxide is added, but the colour
will quickly disappear as the solution is mixed. When this
happens, slow the burette to drop-by-drop addition.
9. When the vinegar solution turns pink and remains that
colour even with mixing, the titration is complete. Close the
tap (or pinch valve) of the burette.
10. Note the remaining level of the sodium hydroxide solution in
the burette. Remember to read from the bottom of the
meniscus.
11. Subtract the initial level from the remaining level to
figure out how much titrating solution we have used.
12. For each vinegar that we test, repeat the titration at
least three times.
:: EXPERIMENT 1 ::
Take the laboratory vinegar in the conical flask and do the
titration with NaOH as mentioned.

OBSERVATIONS:-

Sr Volume in Burette Reading Volume of


No. Vinegar Solution Initial Final NaOH
(in ml) (in ml) (in solution used
ml) (in ml)
1 20 0 15.2 15.2
2 20 0 15.2 15.2
3 20 0 15.2 15.2
Concordant Value = 15.2 ml

CALCULATIONS:-
We know that:-
M CH COOH X V CH COOH
=M NaOH X V NaOH
3 3

M NaOH X V NaOH
M CH 3 COOH = V
CH 3 COOH

0.5 X 15.2
M CH COOH =
3
20
= 0.38 mol/L
Strength of acetic acid = 0.38 X 60 g/L
= 22.8 g/L
:: EXPERIMENT 2 ::
Take the household vinegar in the conical flask and do
the titration with NaOH as mentioned.

OBSERVATIONS:-

Sr Volume of Burette Reading Volume of


No Vinegar Initial Final NaOH solution
Solution(in (in ml) (in used (in ml)
ml) ml)
1 10 0 13.5 13.5
2 10 0 13.5 13.5
3 10 0 13.5 13.5
Concordate Volume = 13.5 ml

CALCULATIONS:-
We know that:-
M CH COOH X V CH COOH =M NaOH X V NaOH
3 3

M NaOH X V NaOH
M CH 3 COOH = V
CH 3 COOH

0.5 X 13.5
M CHCOOH =
3
10
= 0.675 mol/L
Strength of acetic acid = 0 .675 X 60
=40.5 g/L
:: EXPERIMENT 3 ::
Take the wine vinegar in the conical flask and do the titration
with NaOH as mentioned.

OBSERVATIONS:-
Sr Volume of Burette Reading Volume of NaOH
No. Vinegar Initial Final solution used (in
solution(in (in ml) (in ml)
ml) ml)
1 10 0 24 24
2 10 0 24 24
3 10 0 24 24
Concoradant Volume = 24 ml

CALCULATIONS:-
We know that:-
M CH COOH X V CH COOH =M NaOH X V NaOH
3 3

M NaOH X V NaOH
M CH 3 COOH = V
CH 3 COOH

0.5 X 24
M CH COOH =
3
10
= 1.2 mol/L
Strength of acetic acid = 1.2 X 60 g/L
= 72 g/L
:: RESULT ::
➢ Strength of acetic acid in laboratory vinegar = 22.8 g/L
➢ Strength of acetic acid in household vinegar = 40.5 g/L
➢ Strength of acetic acid in wine vinegar = 72 g/L

Graphically plotting various vinegar samples in accordance with


the amount of acetic acid present in them we present a
stunning find :-

Amount of acetic acid in various vinegars


80

70

60
Strength of acetic acid

50

40

30

20

10

0
Laboratory Vinegar Household Vinegar Wine Vinegar

Order of amount of acetic acid in vinegar is:-


Wine Vinegar > Household Vinegar > Laboratory Vinegar
:: PRECAUTIONS ::

• Transfering of measured vinegar into a


measuring flask should be done very carefully .
• Measuring must be performed carefully.
• Look at the meniscus of solution at eye level to
avoid parallax.
• Look at the lower meniscus in the light coloured solution
and upper meniscus in the dark coloured solution
because of visibility.
• Do not forget to add distilled water to the vinegar.
:: BIBLIOGRAPHY ::

1. Comprehensive Lab Manual for Class XII by


Laxmi Publication.
2. www.icbse.com
3. www.scribd.com

You might also like