SEL-311L OVERREACHING

IMPEDANCE PILOT PROTECTION

LABORATORY

BRANDON VAN LOON

SENIOR PROJECT

ELECTRICAL ENGINEERING DEPARTMENT

CALIFORNIA POLYTECHNIC STATE UNIVERSITY

SAN LUIS OBISPO

2015

1
ACKNOWLEDGEMENTS
I would like to thank Dr. Shaban and Dr. Nafisi for giving me a solid foundation in power systems
analysis and protection. Their knowledge and ability to teach has been unparalleled. Thanks to Jaime
and the other support staff for the work they do to support the lab equipment and students in their
projects.

2
ABSTRACT
The objective of this senior project is to protect a three terminal transmission line during fault
conditions using the SEL-311L microprocessor based relay and communication assisted permissive
over-reaching transfer trip protection. The SEL-311L’s directional distance elements are
programmed to trip on internal faults while faults external to the zones of protection are ignored.
Upon sensing a fault condition, the relay issues a trip command to the local breaker and a permissive
key for tripping to the remote relay via fiber optic communication. When a permissive key is
received and all other permissive conditions have been satisfied, the remote relay issues a trip
command to its breaker. Included in this senior project are lab materials for students who wish to
complete the lab or for integration into a power protection laboratory in the future. The lab
introduces Over-reach concepts and Zone 2 protection. Students gain experience in programming
SEL relays, testing protection functionality, and protective relay logic.

3
TABLE OF CONTENTS
ACKNOWLEDGEMENTS ........................................................................................................................... 2

ABSTRACT ........................................................................................................................................................ 3

LIST OF TABLES ............................................................................................................................................ 5

LIST OF FIGURES .......................................................................................................................................... 6

1 INTRODUCTION AND BACKGROUND ...................................................................................... 7

1.1 PROJECT DEVELOPMENT ....................................................................................................... 7

1.2 THEORY OF OPERATION ........................................................................................................ 8

2 REQUIREMENTS, SPECIFICATIONS, AND BLOCK DIAGRAM .......................................12

2.1 CUSTOMER REQUIREMENTS ...............................................................................................12

2.2 ENGINEERING SPECIFICATIONS ......................................................................................13

2.3 BLOCK DIAGRAM LEVEL 0 ...................................................................................................14

2.4 BLOCK DIAGRAM LEVEL 1 ...................................................................................................17

3 DESIGN...................................................................................................................................................19

4 DEVELOPMENT AND CONSTRUCTION ..................................................................................25

4.1 EQUIPMENT.................................................................................................................................25

4.1.1 CIRCUIT BREAKER ...........................................................................................................25

4.1.2 SEL-311L .................................................................................................................................26

4.1.3 LINE IMPEDANCE.............................................................................................................26

4.1.4 SEL-2924..................................................................................................................................26

4.2 CONSTRUCTION ........................................................................................................................26

4.3 CONFIGURATION .....................................................................................................................27

4.4 OPERATION .................................................................................................................................34

5 TESTING.................................................................................................................................................35

5.1 TEST PROCEDURES ..................................................................................................................35

4
 5.1.1 BREAKER CONTROL VERIFICATION ......................................................................36

5.1.2 MULTI-SOURCE SYSTEM ................................................................................................36

6 ANALYSIS ...............................................................................................................................................37

6.1 INTERNAL LL ..............................................................................................................................37

7 CONCLUSION ......................................................................................................................................39

8 APPENDICES ........................................................................................................................................40

8.1 WBS, COST ESTIMATE, AND GANTT CHART ................................................................40

8.2 CONSTRUCTION DRAWINGS ...............................................................................................45

8.3 CIRCUIT BREAKER OPERATION ........................................................................................46

8.4 SEL 311-L PILOT PROTECTION LABORATORY MANUAL ........................................48

8.5 REFERENCES ...............................................................................................................................56

LIST OF TABLES
TABLE 2-1 REQUIREMENTS AND SPECIFICATIONS ..................................................................13
TABLE 2-2 LEVEL 0 BLOCK DIAGRAM INPUT / OUTPUT FUNCTIONALITY ..................15
TABLE 2-3 LEVEL 1 BLOCK DIAGRAM INPUT / OUTPUT FUNCTIONALITY .................17
TABLE 3-1 TRANSMISSION LINE & LOAD PARAMETERS .........................................................20
TABLE 8-1 WBS .............................................................................................................................................40

5
LIST OF FIGURES
FIGURE 1-1 NON-DIRECTIONAL R-X DIAGRAM............................................................................ 9
FIGURE 1-2 RING TOPOLOGY ................................................................................................................ 9
FIGURE 1-3 RELAY ZONES OF PROTECTION ...............................................................................10
FIGURE 1-4 DIRECTIONAL DISTANCE MHO DIAGRAM ..........................................................10
FIGURE 1-5 POTT LOGIC.........................................................................................................................11
FIGURE 2-1 LEVEL 0 BLOCK DIAGRAM ...........................................................................................16
FIGURE 2-2 LEVEL 1 BLOCK DIAGRAM ...........................................................................................18
FIGURE 3-1 SINGLE LINE DIAGRAM .................................................................................................19
FIGURE 3-2 LOAD FLOW STATES ........................................................................................................21
FIGURE 3-3 MHO DIAGRAM ..................................................................................................................24
FIGURE 4-1 LINE PARAMETERS...........................................................................................................28
FIGURE 4-2 PHASE DISTANCE..............................................................................................................29
FIGURE 4-3 OUTPUT CONTACTS.........................................................................................................30
FIGURE 4-4 LINE CURRENT DIFFERENTIAL SETTINGS ..........................................................31
FIGURE 4-5 CLOSE & RECLOSE LOGIC ............................................................................................32
FIGURE 4-6 COMMUNICATIONS ASSISTED TRIPPING ..............................................................33
FIGURE 4-7 87L TRANSMIT EQUATIONS ........................................................................................34
FIGURE 6-1 LINE TO LINE FAULT WEST .........................................................................................37
FIGURE 6-2 LINE TO LINE FAULT CENTER ...................................................................................38

6
1 INTRODUCTION AND BACKGROUND
Implementation of a Permissive Overreaching Transfer Trip protection (POTT) scheme relies on
the application of at least two directional distance (21) units. Distance units require monitoring of
both current and voltage to determine the impedance of the connected circuit. During low
impedance conditions, the relay is programmed to trip the breaker to prevent over-current
conditions from damaging the transmission line and connected equipment. To achieve POTT
protection, the directional distance units or relays are connected via a communications channel.
When either relay detects a fault condition internal to the line, a distance element bit is asserted and
the relay waits for a permissive trip signal from the opposite relay. In order to receive the trip signal,
the other relay must sense the fault condition, issue the trip signal, and send it via the
communications channel. Once both of the distance elements have asserted and the permissive trip
or key bits have been asserted, the relays close their respective trip contacts. The trip signal is then
sent to the trip coil of the breaker causing the breaker to operate and open. Once both breakers
have opened, any fault condition that existed in the protected region of the line is now electrically
isolated.

1.1 PROJECT DEVELOPMENT

Dr.Shaban originally developed the idea and gave it to me for further development and
implementation. The experiment will hopefully be included in the EE444 or a Power Protection
laboratory class and executed by students interested in power systems protection and SEL relays.
The project requirements and specifications were developed over a series of conversations with
Dr.Shaban. Upon completion of the lab, students will be able to implement POTT and PUTT
impedance protection schemes on a tapped multi-source transmission line using the SEL-311L
relays and fiber optic communication. In the future, the power faculty hopes to establish an
operational micro-grid with the intent of integrating protection and analyzing system functionality
when fault conditions appear at different locations in the system. This project represents one piece
of that system. The lab’s delivery date is June 2015, at which time the lab will be fully documented
and operational.

7
The transmission line consists of 100mH inductors in series with 10Ω power resistors. The line
connects to a tapped load comprised of three wye connected power resistors. System breakers were
available and chosen based on past student design. The breaker boxes consist of manual trip/close
contacts and a three-pole contactor which simulates the fast operation of a high-voltage circuit
breaker. The circuit breaker can be automatically operated by connecting the SEL relay to the
appropriate coil contacts. The source(s) are three-phase at 208VLL which is available at all of the lab
benches in the power labs.

My knowledge of power protection was minimal at the beginning of this project and required me to
rely on the SEL-311L instruction manuals provided by Schweitzer Engineering Laboratories (SEL).
SEL produces thorough documentation for their relays including application notes on advanced
configurations such as POTT and PUTT. SEL allows students to enroll in a Computer Based
Training (CBT 101) to gain basic familiarity with their relaying system. The CBT allowed me to
understand the fundamentals of communicating and programming the relay. The department was
able to purchase CBT 104 which further introduced relay logic programming. Dr. Shaban’s EE518
class notes, and Protective Relaying Principles, and Applications 4th Edition, by J. L. Blackburn, and T. J.
Domin, were heavily utilized as resources for this project [1].

1.2 THEORY OF OPERATION

Distance protection requires measurement of both current and voltage to determine the impedance
of a line and connected load at a given time. The impedance for a transmission line network is
determined during design phase and is used as a starting point for the design of the distance
protection system. The transmission line impedance is a physical quantity that remains generally
constant under normal operating conditions. Any impedance detected by the relay lower than 100%
of the line impedance indicates a fault condition on that line. The non-directional distance relay zone
of protection is represented graphically by Figure 1-1. The diagram consists of a circle centered at
zero. The circle’s radius represents the complex impedance value at which the relay will pick up and
issue a trip. The non-directional nature of this configuration poses a problem for protection
engineers because of limitations it poses for coordination. Regardless of whether the low impedance
condition is caused by a fault internal to the line or external to the line, the relay will see a low
impedance and pickup. This becomes an issue when designing non radial systems, commonly

8
referred to as loop systems, because the low impedance condition could cause the relay to pick-up
and the breaker to open a non-faulted zone. Adding directional capabilities to the relay allows the
engineer to design the system so that fault conditions are cleared by the most appropriate protection
devices. The appropriate device is that which causes the least amount of system to be disconnected
while maintaining system stability. The graphical representation below in figure 1-2 depicts the
opening of a non-faulted transmission line.

FIGURE 1-1 NON-DIRECTIONAL R-X DIAGRAM

FIGURE 1-2 RING TOPOLOGY

For loop systems (ring topology) and other non-radial systems, adding a directional unit and
communication to the distance relay allows the protection engineer to create zones of protection
that do not necessarily extend into other devices areas of protection. Multiple zones with varying
impedances and time delay settings can be used to create backup protection for other devices close
to the line if necessary. Protection for a line is accomplished with two relays who both look towards
opposite ends of the transmission line as shown in figure 1-3. Each relay’s zone of protection

9
overlaps. During internal Zone 2 fault conditions, the relays should detect the fault, issue a trip key
command to the relay at the opposite end of the line, and assert its own zone 2 element.

FIGURE 1-3 RELAY ZONES OF PROTECTION

FIGURE 1-4 DIRECTIONAL DISTANCE MHO DIAGRAM

The two most popular schemes for communication assisted distance relaying are POTT and PUTT
protection. Permissive Overreaching Transfer Trip requires the distance element (impedance
element) to assert as well as receive a trip key command from the relay at the remote end of the line
as shown in the logic diagram below. Permissive Under-reaching Transfer Trip scheme is beyone the
scope of this project.

10
FIGURE 1-5 POTT LOGIC

11
2 REQUIREMENTS, SPECIFICATIONS, AND BLOCK DIAGRAM

2.1 CUSTOMER REQUIREMENTS

Two separate meetings with Dr. Shaban early this year identified his needs and requirements. The
system’s main objective is to protect a transmission line using the permissive overreaching transfer
trip scheme (POTT). Two SEL311-L relays connected via fiber optic communication protect a
transmission line fed from two independent sources. At the center of the line, a third terminal is
connected which feeds a wye connected load. The sources will both feed the load under normal load
conditions. Fault conditions are then introduced into the system at different nodes internal and
external to the transmission line system. Single line to ground (SLG), double line to ground (DLG),
line to line (LL), and line to line to line (LLL) fault conditions are applied to the system at the
locations specified in Figure 3-1. Faults internal to the transmission line will result in a trip while
external faults at the load and beyond the transmission line are ignored. The relays detect Zone 2
faults. All Zone 2 trips will require a permissive trip key from each relay to trip the circuit breakers.

The associated lab materials found in the appendix introduce distance relays and basic relay
programming concepts to senior level electrical engineering students. The laboratory allows students
to gain hands-on experience with the SEL 311-L relay and implement an operational POTT
protection scheme.

The requirements and specifications found below in Table 2-1 are based on the customer needs
assessment and follow the IEEE1233 standard for requirements development [3]. Marketing
requirements were developed through analyzing the ‘Customer Needs Assessment’ (1.2). The
requirements analyzed and Engineering Specifications developed satisfy marketing and customer
requirements. The engineering specifications developed using the IEEE1233-6.2 ‘Properties of a
Requirement’ (p.12) [3].

12
2.2 ENGINEERING SPECIFICATIONS

TABLE 2-1 REQUIREMENTS AND SPECIFICATIONS

Customer Engineering
Justification
Requirements Specifications
2.2.1.1 Use Schweitzer Engineering Teaching SEL 311-L is the main objective of
2
Laboratories relay SEL-311L. the laboratory.

2.2.1.2 Use copper wire rated for at

Minimum gauge of wire provides margin of
1 least 15 A continuous current or
safety.
greater.

2.2.1.3 All components have 600V

1 All lab voltages below 600V. Safety
insulation rating or greater.

2.2.1.4 Transmission Line model Labeling increases safety and decrease lab
connection points labeled and setup time. Lab manual reference conveys
1
referenced in accompanying lab added information and increases learning
manual. efficacy.

2.2.1.5 Transmission Line model

Speeds lab setup. Increases safety through
1 capable of accepting banana type
recessing and guarding live parts.
connectors.

2.2.2.1 SEL 311-L relays shall be

Required by equipment manufacturer for
1 programmed via Desktop PC over
connectivity and programming.
existing serial connection.

2.2.2.2 SEL 311-L relays achieves Enables POTT protection. Teaches students
1 pilot communication via fiber optic about pilot protection and relay
communication. communication.

Allows me to further my knowledge about

2.2.2.3 Laboratory capable of SCADA
2 SEL SCADA. Teaches students about relay
via SEL-2032 RTAC.
communication.

2.2.2.4 Relay programmed using

2 Enables POTT protection scheme.
distance protection.

2.2.2.5 Transmission line ends Facilitates students learning: over-reach,

2
sourced separately. under-reach, and zone protection.

2.2.2.6 Manual fault propagation.

Provides student control. Allows for internal
2, 3 Student controlled fault condition and
and external fault locations.
location.

2 2.2.2.7 Zone 1 and Zone 2 protection. Satisfies zone protection requirement

2.2.2.8 Low Current (less than 5 A) Provides margin of safety and prevents relay
1, 2, 3
relay inputs. damage.

13
 2.2.4.1 The Laboratory costs less than Low cost increases lab feasibility decreases EE
2, 3, 4
$500 (not including SEL relays). department economic burden.

2.2.5.1 Laboratory designed February

1 Milestone facilitates timely graduation.
20, 2015.

2.2.5.2 Laboratory building begins

1 Milestone facilitates timely graduation.
March 1, 2015.

2.2.5.3 Laboratory testing and

5, 7 Milestone facilitates timely graduation.
programming begins April 1, 2015.

2.2.5.4 Supporting documentation

8 Milestone facilitates timely graduation.
completed June 12, 2015.

2.2.6.1 Student laboratory manual. Facilitates learning and meets customer

8
2.2.6.2 Instructor laboratory manual. requirements.

Customer Requirements
1. Senior-level power students build and operate system safely.
2. Teaches students programming concepts related to SEL-311L POTT protection and
communication.
3. Introduces over-reach and under-reach concepts.
4. Pilot & zone protection concepts introduced.
5. Completed during three hour lab period.
6. Accompanying lab documentation.
7. Low Cost.
8. Senior Project completed before graduation June 2015.

2.3 BLOCK DIAGRAM LEVEL 0

The level 0 block diagram in Figure 2-1 consists of a single block and describes the basic inputs and
outputs from the SEL311-L relay system, breaker, transmission line, and communication system.
The left side of the block diagram describes the inputs and outputs from the West end of the Line
and the right side describes the inputs and outputs from the East side of the Line. The left and right
sides of the diagram contain both voltage and current inputs from the line. These measurements are
used to calculate the perceived impedance of the line to determine if fault conditions are present.
The top of the block represents relay and device power and communication connections. Relay
equipment is powered via 120V AC. Breaker control and contactor voltage is 125V DC. The bottom
of the block describes inputs and outputs from the relays and breakers to remote annunciator panels
typically found in control rooms and on medium voltage switch gear. Figure 2-2 provides a level
two-block diagram view of the system and provides more insight into the physical connection of the

14
equipment. A fiber optic connection provides a communications path between the relays. Serial
connections provide SCADA throughput to peripheral devices.

TABLE 2-2 LEVEL 0 BLOCK DIAGRAM INPUT / OUTPUT FUNCTIONALITY

Input / Output Functionality

Current inputs processed by relay microprocessor
1. West Line Current Input From CT (Ia, Ib, Ic)
and analyzed for presence of fault conditions. (I)
Voltage used in conjunction with current
2. West Line Voltage Input From PT (Va, Vb,
determines line impedance and presence of fault
Vc)
conditions. (I)
Communication via fiber optics, ensures high
3. West Pilot Communication (Tx, Rx) speed tripping and establishes pilot
communication capabilities. (IO)
Establishes information channel and data
4. West SCADA (Serial)
aggregation for HMI and remote control. (IO)
5. West Trip Alarm Breaker Provides relay with breaker trip confirmation. (I)
6. West Alarm Breaker Provides relay with breaker status. (I)
Current inputs processed by relay microprocessor
7. East Line Current Input From CT (Ia, Ib, Ic)
and analyzed for presence of fault conditions. (I)
Voltage used in conjunction with current
8. East Line Voltage Input From PT (Va, Vb, Vc) determines line impedance and presence of fault
conditions. (I)
Communication via fiber optics, ensures high
9. East Pilot Communication (Tx, Rx) speed tripping and establishes pilot
communication capabilities. (IO)
Establishes information channel and data
10. East SCADA (Serial)
aggregation for HMI and remote control. (IO)
11. East Trip Alarm Breaker Provides relay with breaker trip confirmation. (I)
12. East Alarm Breaker Provides relay with breaker status. (I)
13. Power 120V AC Power for relay equipment. (I)
14. Station Battery 125VDC Power for simulate breaker equipment. (I)
Provides user serial access programming
15. PC Communication
capabilities. (I)

15
FIGURE 2-1 LEVEL 0 BLOCK DIAGRAM

16
2.4 BLOCK DIAGRAM LEVEL 1

TABLE 2-3 LEVEL 1 BLOCK DIAGRAM INPUT / OUTPUT FUNCTIONALITY

Input / Output Functionality

Current inputs processed by relay microprocessor
1. West Line Current Input From CT (Ia, Ib, Ic)
and analyzed for presence of fault conditions. (I)
Voltage used in conjunction with current
2. West Line Voltage Input From PT (Va, Vb, Vc) determines line impedance and presence of fault
conditions. (I)
Communication via fiber optics, ensures high
3. West Pilot Communication (Tx, Rx) speed tripping and establishes pilot
communication capabilities. (IO)
Establishes information channel and data
4. West SCADA (Serial)
aggregation for HMI and remote control. (IO)
5. West Trip Alarm Breaker Provides relay with breaker trip confirmation. (I)
6. West Alarm Breaker Provides relay with breaker status. (I)
Current inputs processed by relay microprocessor
7. East Line Current Input From CT (Ia, Ib, Ic)
and analyzed for presence of fault conditions. (I)
Voltage used in conjunction with current
8. East Line Voltage Input From PT (Va, Vb, Vc) determines line impedance and presence of fault
conditions. (I)
Communication via fiber optics, ensures high
9. East Pilot Communication (Tx, Rx) speed tripping and establishes pilot
communication capabilities. (IO)
Establishes information channel and data
10. East SCADA (Serial)
aggregation for HMI and remote control. (IO)
11. East Trip Alarm Breaker Provides relay with breaker trip confirmation. (I)
12. East Alarm Breaker Provides relay with breaker status. (I)
13. Power 120V AC Power for relay equipment. (I)
14. Station Battery 125VDC Power for simulate breaker equipment. (I)
Provides user serial access programming
15. PC Communication
capabilities. (I)
16. Manual Open / Close (TYP) Manually opens and closes breaker contactor.
17. Trip / Close (TYP) Relay Issued trip/close command

17
FIGURE 2-2 LEVEL 1 BLOCK DIAGRAM

18
3 DESIGN
The design began with the development of a single line diagram of the system as shown in Figure 3-
1. The single-line diagram identifies the systems main components shows how they are electrically
connected.

FIGURE 3-1 SINGLE LINE DIAGRAM

The three terminal transmission line network consists of a line and load tapped at the center of the
line. The relays are located at the west and east ends and look towards opposite ends of the line. The
relays monitor phase current and voltage. The load consists of three wye connected resistor-inductor
pairs. Datasheets and instruction manuals for all the equipment in the system was gathered and the
nominal system parameters are tabulated in Table 3-1.

19
 TABLE 3-1 TRANSMISSION LINE & LOAD PARAMETERS
Resistance Inductance Inductive
West
(Ω) / phase (H) / phase Reactance (Ω)
L1 21 200mH 75.698
L2 21 200mH 75.698
L3 21 200mH 75.698
Load 10.5 37.698
Source 10.5

The impedance seen at a relay is affected by the load conditions on the system. Seven possible load
flow states were identified and taken into consideration when designing the system. Figure 3-2
identifies the possible states the system can enter under normal operation. Figure 3-2-A (A) was
implemented in the lab. Time did not permit for further in-depth study of the effect of load
conditions found in Figure 3-2 on system functionality.

20
FIGURE 3-2 LOAD FLOW STATES

21
The design constraints for relay Zone 2 impedance protection require that the relays overreach the
line by 120% of the line. Consideration of the load impedance magnitude with respect to each relay
and source was taken into consideration in order to prevent overreaching into the load.
Overreaching in to the load could cause false tripping during high load conditions and under-
reaching the transmission line would result in non-operation during internal faults near the relays.
To prevent non-operation and ensure overlapping Zone 2 protection the relay settings were chosen
to be 120% of line impedance. To achieve tripping, the Zone 2 mho circles were overlapped and set
to reach 120% of the impedance of the line. Since the load is fed by two sources, the perceived
impedance increases because of load sharing. Under normal load conditions, the relays should see an
impedance of 200% of the line. If load conditions change and current reverses direction, the relays
should block operation further testing would be required to verify operation.

For faults near one of the relays, the effective impedance seen by the remote relay, shown in
Equation 1. Will be one half the impedance of the line in parallel with connected load plus one half
of the line. Equation 2 calculates the perceived impedance of the line when a fault condition exists at
the remote relay. Equation 3 calculates 120% of the perceived impedance of the line when a fault
condition exists at the remote relay.

𝑍𝐿𝐼𝑁𝐸 𝑍𝐿𝐼𝑁𝐸
𝑍𝐹𝑅𝑅 = ( ||𝑍𝐿𝑂𝐴𝐷 ) + Ω Eq.1
2 2

21 + 75.698𝑗 21 + 75.698𝑗
𝑍𝐹𝑅𝑅 = ( )||(10 + 37.698𝑗)) + ( )Ω
2 2

𝑍𝐹𝑅𝑅 = 0.75 × 𝑍𝐿𝐼𝑁𝐸 Ω Eq.2

𝑍𝐹𝑅𝑅 = 58.918∠ 74.5 Ω

1.2 𝑍𝐹𝑅𝑅 = 70.70∠ 74.5 Ω Eq.3

2𝑍𝐿𝐼𝑁𝐸 = 157.11∠ 74.5 Ω Eq.4

22
 Relays Perceived Impedance Based on Fault
Location
0.8
PERCEIVED FRACTIONAL 0.7
IMPEDANCE OF LNE 0.6
0.5
0.4
0.3
0.2
0.1
0
0 0.1 0.2 0.3 0.4 0.5
DISTANCE FROM CENTER OF TRANSMISSION LINE

FIGURE 3-3 RELAYS PERCEIVED IMPEDANCE

DESIGN EQUATIONS:

𝑍2𝑥 = 1.2(21 + 75.698𝑗) Eq. 5

𝑍2𝑥 = 94.268 ∠ 75° Ω

94.268
𝑍2𝑃 = cos(75°−75.698°) Ω Eq. 6

𝑍2𝑃 ≈ 94Ω

Z2P represents the diameter of the Zone 2 Mho circle at 75 degrees. Equation 5 and Equation 6
calculate the appropriate diameter for the Mho circle based strictly on the physical impedance of the
line. Consideration of the load conditions are not taken into account in these equations. Loads or
faults whose impedances fall within the circle and seen by both relays, will operate the Zone 2
elements and trip the breakers.

23
For this project, loading and perceived impedance was taken into account. The settings applied to
the relays allow for Zone 2 impedance overlapping based on the calculated ZFRR . The SEL-311
maximum reach setting is 64Ω. Without additional equipment to reduce the secondary impedance to
the relay, full 120% distance line protection is not possible.

POTT relies on communication between the relays for keying. Only when a relay receives a key
signal and sees a fault on the line will the relay trip. In this configuration if communication is lost,
the relay will still operate but must wait for the Zone timer to timeout before tripping. Waiting for
the timer to timeout increases, the total energy released, and increases the probability of equipment
damage and system instability. The timer allows for downstream device coordination and breaker
tripping. Figure 3-3 depicts the systems MHO diagram.

FIGURE 3-4 MHO DIAGRAM

24
4 DEVELOPMENT AND CONSTRUCTION

4.1 EQUIPMENT

The project required the following equipment:

(2) SEL-311L

(6) Power Resistor / Inductor combination unit (20+37j) Ω

(1) SEL-2924 Serial to Bluetooth Adapter

(100’) #14 Wire

(50) #14 Fork Terminals

(1) Multi-meter

(2) Circuit Breakers

(1) Wire Strippers

(1) Terminal Crimper

(20) 3’ Banana to Banana Leads

(10) Short Banana to Banana Leads

4.1.1 CIRCUIT BREAKER

The circuit breakers used in this project were built by Dr. Shaban’s student. The circuit breaker
includes automatic and manual trip/close capability. The SEL relay outputs can be wired to the
breaker unit allowing remote trip/ close commands to be sent from the relay to operate the breaker
automatically. For testing faults at a node, the built-in fault switch can be wired to introduce fault
conditions into the test circuit. The line-side fault switch terminals are connected to the three phases
of the node and the load side terminals of the fault switch are connected together in the desired fault
condition.

25
4.1.2 SEL-311L

The SEL-311L is a differential current relay used to protect high voltage transmission lines. The
relay includes 4 zone phase distance and ground distance capabilities. Differential and other
communications assisted protection schemes, including POTT, utilize the relays fiber optic
communications channel for data transfer between system IEDs.

4.1.3 LINE IMPEDANCE

Line impedance was achieved using available electrical engineering department resistor & reactor
units built by the department’s lab technicians. The unit consists of (2) 10 ohm power resistors rated
at 160W and a 100mH 5A reactor all connected in series. Each electrical node is available for use via
a banana type connector standoff.

Part Numbers:

(1) Hammond Manufacturing 195T5 Reactor

(2) Ohmite WFH160 Power Resistor

4.1.4 SEL-2924

EIA-232 to Bluetooth serial adapter allows communication between the relay and computer
terminal. The adapter is useful when working with RS-232 devices in the field and is a wireless
substituted for its wired counterpart. The adapter comes with a USB rechargeable lithium battery.

4.2 CONSTRUCTION

The lab required approximately 6 hours to wire and confirm the connections. Three-quarters of a
standard power lab bench was needed to house the required equipment. Connections were made
directly to the back of the relays and source using #14 wire and fork terminal connectors. Relay
mimic panels are currently being manufactured by students to allow all lab connections to be made
with banana to banana type cables and connectors. Once the mimic panels are completed, overall

26
wiring time should be reduced to under one hour. For this system, the same source was connected
to each end of the system to model a loop system connection. For integration into the Cal Poly
micro grid separate synchronized generation can be applied to the system with similar functionality
obtained.

4.3 CONFIGURATION

The relays were programmed with the impedance settings calculated in the design section. Line
parameters neglect the effect of the load and treat the line as a continuous line impedance from the
local to remote relay terminal. The CT and VT settings were set to 1 because no PTs or VTs were
used in the project and no ratio from primary to secondary exists. All voltage and current inputs to
the relays are actual system values. Figure 4-1 & 4-2 show the line parameter settings and distance
settings entered into the AcSELerator.

27
FIGURE 4-1 LINE PARAMETERS

28
 FIGURE 4-2 PHASE DISTANCE
The following settings (Figures 4-3 - 4-6) represent the trip logic equations, output contacts, and
communication settings required to achieve POTT. Figure 4-3 shows the Words when asserted will
close the output contacts on the relays. OUT103 when asserted will trip the circuit breaker and is
asserted when word !TRIP*!OC are asserted. OUT102 is high when the Close command is asserted.
The breaker requires a momentary close and will remain closed until the trip command has been
issued. Although differential protection was not used in this project, the 87 differential settings were
left active to allow for utilization of the 87 channel communication via the fiber optic connection.

29
FIGURE 4-3 OUTPUT CONTACTS

30
FIGURE 4-4 LINE CURRENT DIFFERENTIAL SETTINGS

31
FIGURE 4-5 CLOSE & RECLOSE LOGIC

32
FIGURE 4-6 COMMUNICATIONS ASSISTED TRIPPING

33
 FIGURE 4-7 87L TRANSMIT EQUATIONS

4.4 OPERATION

After wiring and system functionality has been verified, the sources can be applied and breakers
closed. Special care was taken to ensure that the power resistors were not being overheated by the
power dissipated through them. Fault conditions are then applied to the nodes specified on the
single line construction drawing located in the appendix. The system is energized and fault switched
on momentarily. If the relays are functioning as designed, they should immediately operate and open
both breakers, which can be confirmed by the red breaker closed lights transition to two green

34
breaker open lights located on the circuit breaker boxes. In addition, the relays targets displayed on
the front panel should light up when a fault condition is sensed. All wiring changes including
moving the fault nodes to a different location should be performed with the system de-energized.

5 TESTING

5.1 TEST PROCEDURES

The following are test procedures for verifying the circuit’s electrical and mechanical connections
prior to energizing the circuit. Verifying the circuit’s electrical and mechanical connections are
imperative to protect both the student and equipment from inadvertent damage.

POINT TO POINT AND MECHANICAL CHECK

The mechanical connections should be checked. With the circuit de-energized, gently pull on the
wires and look for wire movement or displacement at the mechanical connection. If the wire
connections move, further steps need to be taken to secure the connection. A point to point check
using the construction drawings should be done to verify that all connections have been
appropriately made. These tests should help eliminate wiring errors and decrease the likely hood a
loose or misplaced wire.

WIRING CONTINUITY CHECK

With the load open-circuited and sources de-energized and open-circuited, a continuity / resistance
check should be made from the source to the load using a standard multi-meter. All three phases
from both sides of the line should be recorded and verified for consistency across all 6 of test
points. If any of the test points show a low resistance, resistance difference of 25% or more, or
infinite resistance the circuit should not be energized and all connections should be verified. Do not
energize the circuit until resistances are equal and approximately 35 ohms from source to load.

35
5.1.1 BREAKER CONTROL VERIFICATION

With the three phase ac source de-energized, energize the DC control voltage and test manual open
close breaker functionality prior to energizing the circuit. Verify that the trip and close commands
can be issued from the serial terminal within the AcSELerator terminal and that the breaker
responds accordingly.

5.1.2 MULTI-SOURCE SYSTEM

If utilizing multiple sources, care must be taken to ensure the systems are synchronized and have
proper phasing prior to closing the breaker. Failing to properly synchronize and phase independent
sources can result in equipment damage and injury. Procedures for synchronizing and phasing are
beyond the scope of this senior project.

36
6 ANALYSIS
Internal line to line faults were selected for analysis because they result in the lowest fault current. By
analyzing relay functionality at the lowest fault current magnitude possible, we can deduce that the
relay will operate under more extreme fault current conditions.

6.1 INTERNAL LL

FIGURE 6-1 LINE TO LINE FAULT WEST

In Figure 6-1 and Figure 6-2 Phases A & B have been faulted. Figure 6-1 the system is faulted at the
West node as shown on the single line diagram. Figure 6-2 the system is faulted at the Center node

37
as shown on the single line diagram. As seen in the event diagram the fault causes increases in
current and decreases in the voltages seen on those phases. The relay word bit M2P picks up
indicating that a Zone 2 fault has been detected similarly M1P has not picked up indicating the fault
impedance is higher and outside the zone 1 impedance circle. Shortly after the M2P word bit goes
high, a permissive key is received shown as the COMM signal and the trip command issued. Both
breakers opened successfully.

FIGURE 6-2 LINE TO LINE FAULT CENTER

When fault conditions external to the relays were applied, the relays blocked the trip and did not
operate. Blocking trips for faults external to the line allow protection engineers to better coordinate
protection and predict system operation after a fault condition has been cleared.

38
7 CONCLUSION
Permissive over-reaching transfer trip protection is a useful way to provide security to vital
transmission line infrastructure. By overreaching the transmission line and requiring both relays to
sense a fault internal to the line, false trips on faults external to the line become unlikely. The SEL-
311L offers a robust set of protection elements and fiber optic connections for high speed reliable
communication between relays. For long distance transmission lines, POTT is a more secure
alternative to phase distance and overcurrent alone. The multi-source and tapped load system forced
me to think about how system operating and load conditions affect the perceived impedance at the
relays. Careful consideration of system conditions need to be part of a protection analysis to avoid
false trips and non-operation.

39
 8 APPENDICES

8.1 WBS, COST ESTIMATE, AND GANTT CHART

TABLE 8-1 WBS

1 SEL 311 TRANSMISSION LINE DIFFERENTIAL PROTECTION PROJECT TIME TIME TIME
( A) ( M) ( B)
1.1 Concept & Preliminary Design
1.1.1 Customer Requirements Development
1.1.1.1 Customer Requirements Elicitation 1.5 2 4 2.25
1.1.1.2 Requirements Document Development 3 4 8 4.5
1.1.1.3 Literature Research 6 8 16 9
1.1.1.4 Communications Architecture 1.5 2 4 2.25
1.1.1.5 Customer Review & Acceptance 3 4 8 4.5
1.3.1 Engineering Specifications Development
1.3.1.1 Specification Document Development 3 4 8 4.5
1.3.1.2 Customer Review & Acceptance 0.75 1 2 1.125
1.3.1.3 Specification Verification & Traceability 4.5 6 12 6.75
2.1 Detailed Design
2.1.1 Protection Scheme Design
2.1.1.1 Protection Specification & 15 20 40 22.5
Engineering
2.1.1.2 ETAP Model 4.5 6 12 6.75
2.1.1.3 Fault Analysis 1.5 2 4 2.25
2.1.1.4 Preliminary Test Plan 2.25 3 6 3.375
Development
2.1.1.5 Customer Review 0.75 1 2 1.125
2.1.2 Programming Design
2.1.2.1 Differential Trip Pickup 3.75 5 10 5.625
2.1.2.2 Protection Functionality 3.75 5 10 5.625
2.1.2.3 Calibration & Parameters 3.75 5 10 5.625
2.1.2.4 PILOT Protection 3.75 5 10 5.625
2.1.1.5 Customer Review 0.75 1 2 1.125
2.1.3 Design Documentation Development
2.1.4.1 Wiring Diagrams 2.25 3 6 3.375
2.1.4.2 Communications Diagrams 2.25 3 6 3.375
2.1.4.3 Bill of Materials 3 4 8 4.5
2.1.4.4 Customer Review 0.75 1 2 1.125
2.1.4 Customer Design Final Review and
Acceptance
2.1.4.1 Document Review 0.75 1 2 1.125

40
 2.1.4.2 Program review 0.75 1 2 1.125
2.1.4.3 Engineering Review 0.75 1 2 1.125
3.1 Procurement
3.1.1 Locate Available Equipment 1.5 2 4 2.25
3.1.2 Vendor Qualification 1.5 2 4 2.25
3.1.3 Quotation 1.5 2 4 2.25
3.1.4 Purchase 3 4 8 4.5
4.1 Construct
4.1.1 Initial Setup 1.5 2 4 2.25
4.1.2 Wire 5.25 7 14 7.875
4.1.3 Programming 6 8 16 9
4.1.4 Communication Wiring 3 4 8 4.5
4.1.5 Communication Programming 6 8 16 9
4.1.6 Systems Integration 6 8 16 9
5.1 Test
5.1.1 Finalize Test Plan Development 2.25 3 6 3.375
5.1.2 Test Plan Customer Acceptance 0.75 1 2 1.125
5.1.3 Fault Testing 6 8 16 9
5.1.4 Communications Testing 3.75 5 10 5.625
5.1.5 Factory Acceptance Test 1.5 2 4 2.25
6.1 Project Deliverable
6.1.1 Customer Delivery 0.75 1 2 1.125
7.1 Report Deliverables
7.1.1 Functional Specification 3.75 5 10 5.625
7.1.2 Lab Student Material 6 8 16 9
7.1.3 Lab Instructor Materials 6 8 16 9
7.1.4 Customer Review & Acceptance 1.5 2 4 2.25

Time Time Time Estimated Labor

(a) (m) (b) Hours
141 188 376 211.5
* Time (a) x.75 multiplier
* Time (m) x1.0 multiplier
* Time (b) x2.0 multiplier

MATERIAL COST ESTIMATE

Items Provided by Student
Item Unit
# QTY: Item: Cost Total Cost
1 3 500' #14 Stranded $60.00 $180.00
2 1 100 fork terminations $25.00 $25.00
3 1 Misc. Electrical Parts $50.00 $50.00
4 1 Misc. Admin $50.00 $50.00
Subtotal $305.00

41
 Sale
Tax 9.00% Tax $27.45
Total $332.45

Items Provided by Dr. Shaban

Item Unit
# QTY: Item: Cost Total Cost
5 6 Transformers $50.00 $300.00
6 2 SEL 311-L $5,000.00 $10,000.00
7 1 SEL 2042 $2,840.00 $2,840.00
8 2 Fiber Optic Cables $20.00 $40.00
9 4 Circuit Breaker Simulators $200.00 $800.00
Subtotal $13,980.00
Sale
Tax 9.00% Tax $1,258.20
Total $15,238.20

Total Material Cost $15,570.65

Total Estimated Labor Hours 211.50

Labor Rate $125 Hourly
Total Labor Cost $26,375.00

Total Project Cost $41,945.65

Project estimates developed using previous project experience and a Work Breakdown Structure
further identifying work tasks. The total cost estimates how much the project would cost if
contracted to organizations for implementation and engineering for development of a differential
impedance protection system using the SEL-311L.

42
 TABLE 8-2 GANTT CHART

43
44
8.2 CONSTRUCTION DRAWING

PAGE INTENTIONALLY LEFT BLANK

 EXTERNAL INTERNAL EXTERNAL
FAULT FAULT FAULT

SEL 311L SEL 311L

SEL 311 FIBER PILOT COMMUNICATION SEL 311

SOURCE #1 SOURCE #2

CB #1 CB #2

INDICATES
FAULT LOCATION

LOAD

POTT SINGLE LINE DIAGRAM

SCALE: NONE
 WIRE / CABLE SCHEDULE
WIRE / CABLE TERMINATION #1 TERMINATION #2
TYPE: DESCRIPTION: NOTES:
NUMBER: LOCATION: LOCATION:
RELAY WEST CHANNEL X NOTICE RX-TX ROLLOVER BETWEEN
C-1001-1 RELAY EAST CHANNEL X (TX) 930 NM FIBER OPTIC 87 CHANNEL COMMUNICATIONS
(RX) RELAYS
RELAY WEST CHANNEL X NOTICE RX-TX ROLLOVER BETWEEN
C-1001-2 RELAY EAST CHANNEL X (RX) 930 NM FIBER OPTIC 87 CHANNEL COMMUNICATIONS
(TX) RELAYS
C-1003 Z25, Z26, Z27 RELAY EAST WALL OUTLET (120VAC) POWER CORD 16/2 RELAY POWER CONNECTION
C-1004 Z25, Z26, Z27 RELAY WEST WALL OUTLET (120VAC) POWER CORD 16/2 RELAY POWER CONNECTION
SERIAL COMMUNICATIONS FOR RELAY
DB-9 CONNECTOR ONLY CONNECTED WHEN RELAY IS
C-1005 RELAY EAST SERIAL PORT 2 PC SERIAL PORT PROGRAMMING AND TERMINAL
FM-FM LOCALLY ACCESSED BY PERSONELL
ACCESS
SERIAL COMMUNICATIONS FOR RELAY
DB-9 CONNECTOR ONLY CONNECTED WHEN RELAY IS
C-1006 RELAY WEST SERIAL PORT 2 PC SERIAL PORT PROGRAMMING AND TERMINAL
FM-FM LOCALLY ACCESSED BY PERSONELL
ACCESS

C-1001

C-

C-
10

10
01

01-2
-1
C1005
COMPUTER
TERMINAL

C1003 120VAC
POWER
SOURCE

C-1001 C-1006 COMPUTER

TERMINAL
C1

C1
00

0
01
1-2

-1

C-1004

COMMUNICATIONS WIRING DIAGRAM

SCALE: NONE
 SEL- 311L - EAST LINE

W-1121
SOURCE #1 A CURRENT
REFER TO DRAWING
W-1124
POTT_0151-05.DWG

W-1122
SOURCE #1 B CURRENT
REFER TO DRAWING
POTT_0151-05.DWG W-1125 SEL- 311L - WEST LINE
W-1123
SOURCE #1 C CURRENT
REFER TO DRAWING
W-1126
POTT_0151-05.DWG

W-1133
SOURCE #1 A VOLTAGE

REFER TO DRAWING W-1134

POTT_0151-05.DWG SOURCE #1 B VOLTAGE

W-1135
SOURCE #1 C VOLTAGE

W-1127
SOURCE #2 A CURRENT
REFER TO DRAWING
POTT_0151-05.DWG W-1130
WIRE / CABLE SCHEDULE
WIRE / CABLE TERMINATION #1 LOCATION: TERMINATION #2 LOCATION: TYPE:
W-1128
NUMBER:
SOURCE #2 B CURRENT W-1121 SOURCE #1 IMPEDANCE PHASE A EAST LINE RELAY CURRENT PHASE A DOTTED #14 THHN (BLK)
REFER TO DRAWING W-1122 SOURCE #1 IMPEDANCE PHASE B EAST LINE RELAY CURRENT PHASE B DOTTED #14 THHN (RED)
W-1131
POTT_0151-05.DWG W-1123 SOURCE #1 IMPEDANCE PHASE C EAST LINE RELAY CURRENT PHASE C DOTTED #14 THHN (BLUE)
W-1124 EAST LINE RELAY CURRENT PHASE A EAST LINE INDUCTANCE PHASE A #14 THHN (BLK)
W-1129 W-1125 EAST LINE RELAY CURRENT PHASE B EAST LINE INDUCTANCE PHASE B #14 THHN (RED)
SOURCE #2 C CURRENT
W-1126 EAST LINE RELAY CURRENT PHASE C EAST LINE INDUCTANCE PHASE C #14 THHN (BLUE)
REFER TO DRAWING
W-1132 W-1127 SOURCE #2 IMPEDANCE PHASE A WEST LINE RELAY CURRENT PHASE A DOTTED #14 THHN (BLK)
POTT_0151-05.DWG
W-1128 SOURCE #2 IMPEDANCE PHASE B WEST LINE RELAY CURRENT PHASE B DOTTED #14 THHN (RED)
W-1129 SOURCE #2 IMPEDANCE PHASE C WEST LINE RELAY CURRENT PHASE C DOTTED #14 THHN (BLUE)
W-1130 WEST LINE RELAY CURRENT PHASE A WEST LINE INDUCTANCE PHASE A #14 THHN (BLK)
W-1131 WEST LINE RELAY CURRENT PHASE B WEST LINE INDUCTANCE PHASE B #14 THHN (RED)
W-1132 WEST LINE RELAY CURRENT PHASE C WEST LINE INDUCTANCE PHASE C #14 THHN (BLUE)
W-1133 SOURCE #1 PHASE A EAST LINE RELAY VOLTAGE PHASE A #14 THHN (BLK)
W-1136 W-1134 SOURCE #1 PHASE B EAST LINE RELAY VOLTAGE PHASE B #14 THHN (RED)
SOURCE #2 A VOLTAGE
W-1135 SOURCE #1 PHASE C EAST LINE RELAY VOLTAGE PHASE C #14 THHN (BLUE)
REFER TO DRAWING W-1137 W-1136 SOURCE #2 PHASE A WEST LINE RELAY VOLTAGE PHASE A #14 THHN (BLK)
POTT_0151-05.DWG SOURCE #2 B VOLTAGE
W-1137 SOURCE #2 PHASE B WEST LINE RELAY VOLTAGE PHASE B #14 THHN (RED)
W-1138 W-1138 SOURCE #2 PHASE C WEST LINE RELAY VOLTAGE PHASE C #14 THHN (BLUE)
SOURCE #2 C VOLTAGE

INSTRUMENTATION WIRING DIAGRAM

SCALE: NONE
 W-1149 W-1149
W-1150 W-1150
W-1151 W-1151
W-1152 W-1152

SEL- 311L - EAST LINE 125 VDC SOURCE W-1145

LAB BENCH W-1146

W-1101
208V 3 PHASE SOURCE W-1102
LAB BENCH
W-1103

W-1107
LOAD SIDE BREAKER W-1108
REFER TO DRAWING
POTT_0151-05.DWG W-1109

CIRCUIT BREAKER - EAST LINE

W-1153 W-1153
W-1154 W-1154
W-1155 W-1155
W-1156 W-1156

SEL- 311L - WEST LINE 125 VDC SOURCE W-1147

LAB BENCH W-1148

W-1104
208V 3 PHASE SOURCE W-1105
LAB BENCH
W-1106

W-1110
LOAD SIDE BREAKER W-1111
REFER TO DRAWING
POTT_0151-05.DWG W-1112

WIRE / CABLE SCHEDULE CIRCUIT BREAKER - WEST LINE

WIRE / CABLE NUMBER: TERMINATION #1 LOCATION: TERMINATION #2 LOCATION: TYPE: DESCRIPTION: NOTES:
W-1101 SOURCE #1 PHASE A CB EAST LINE PHASE A #14 THHN (BLK) SOURCE TO LINE SIDE CB CONNECTION
W-1102 SOURCE #1PHASE B CB EAST LINE PHASE B #14 THHN (RED) SOURCE TO LINE SIDE CB CONNECTION
W-1103 SOURCE #1 PHASE C CB EAST LINE PHASE C #14 THHN (BLUE) SOURCE TO LINE SIDE CB CONNECTION
W-1104 SOURCE #2 PHASE A CB WEST LINE PHASE A #14 THHN (BLK) SOURCE TO LINE SIDE CB CONNECTION
W-1105 SOURCE #2PHASE B CB WEST LINE PHASE B #14 THHN (RED) SOURCE TO LINE SIDE CB CONNECTION
W-1106 SOURCE #2 PHASE C CB WEST LINE PHASE C #14 THHN (BLUE) SOURCE TO LINE SIDE CB CONNECTION
W-1107 CB EAST LOAD PHASE A EAST LINE IMPEDANCE PHASE A #14 THHN (BLK) LOAD SIDE CB TO LINE IMPEDANCE
W-1108 CB EAST LOAD PHASE B EAST LINE IMPEDANCE PHASE B #14 THHN (RED) LOAD SIDE CB TO LINE IMPEDANCE
W-1109 CB EAST LOAD PHASE C EAST LINE IMPEDANCE PHASE C #14 THHN (BLUE) LOAD SIDE CB TO LINE IMPEDANCE
W-1110 CB WEST LOAD PHASE A WEST LINE IMPEDANCE PHASE A #14 THHN (BLK) LOAD SIDE CB TO LINE IMPEDANCE
W-1111 CB WEST LOAD PHASE B WEST LINE IMPEDANCE PHASE B #14 THHN (RED) LOAD SIDE CB TO LINE IMPEDANCE
W-1112 CB WEST LOAD PHASE C WEST LINE IMPEDANCE PHASE C #14 THHN (BLUE) LOAD SIDE CB TO LINE IMPEDANCE
W-1145 125VDC SOURCE EAST LINE CB +125VDC #14 THHN (BLK)
W-1146 125VDC COMMON SOURCE EAST LINE CB 125DC COMMON #14 THHN (WHT)
W-1147 125VDC SOURCE WEST LINE CB +125VDC #14 THHN (BLK)
W-1148 125VDC COMMON SOURCE WEST LINE CB 125DC COMMON #14 THHN (WHT)
W-1149 EAST LINE RELAY OUT101-1 EAST LINE CB OPEN (CB-1001) #14 THHN (BLUE)
W-1150 EAST LINE RELAY OUT101-2 EAST LINE CB OPEN (CB-1002) #14 THHN (BLUE)
W-1151 EAST LINE RELAY OUT102-1 EAST LINE CB TRIP (CB-1003) #14 THHN (RED)
W-1152 EAST LINE RELAY OUT102-2 EAST LINE CB TRIP (CB-1004) #14 THHN (RED)
W-1153 WEST LINE RELAY OUT101-1 WEST LINE CB OPEN (CB-1001) #14 THHN (BLUE)
W-1154 WEST LINE RELAY OUT101-2 WEST LINE CB OPEN (CB-1002) #14 THHN (BLUE)
W-1155 WEST LINE RELAY OUT102-1 WEST LINE CB TRIP (CB-1003) #14 THHN (RED)
W-1156 WEST LINE RELAY OUT102-2 WEST LINE CB TRIP (CB-1004) #14 THHN (RED)

CIRCUIT BREAKER CONTROL WIRING DIAGRAM

SCALE: NONE
 WIRE / CABLE SCHEDULE
WIRE / CABLE TERMINATION #1 LOCATION: TERMINATION #2 LOCATION: TYPE: DESCRIPTION: NOTES:
NUMBER:
W-1101 SOURCE #1 PHASE A CB EAST LINE PHASE A #14 THHN (BLK) SOURCE TO LINE SIDE CB CONNECTION
W-1102 SOURCE #1PHASE B CB EAST LINE PHASE B #14 THHN (RED) SOURCE TO LINE SIDE CB CONNECTION
W-1103 SOURCE #1 PHASE C CB EAST LINE PHASE C #14 THHN (BLUE) SOURCE TO LINE SIDE CB CONNECTION
W-1104 SOURCE #2 PHASE A CB WEST LINE PHASE A #14 THHN (BLK) SOURCE TO LINE SIDE CB CONNECTION
W-1105 SOURCE #2PHASE B CB WEST LINE PHASE B #14 THHN (RED) SOURCE TO LINE SIDE CB CONNECTION
W-1106 SOURCE #2 PHASE C CB WEST LINE PHASE C #14 THHN (BLUE) SOURCE TO LINE SIDE CB CONNECTION
W-1107 CB EAST LOAD PHASE A EAST LINE IMPEDANCE PHASE A #14 THHN (BLK) LOAD SIDE CB TO LINE IMPEDANCE
W-1108 CB EAST LOAD PHASE B EAST LINE IMPEDANCE PHASE B #14 THHN (RED) LOAD SIDE CB TO LINE IMPEDANCE
W-1109 CB EAST LOAD PHASE C EAST LINE IMPEDANCE PHASE C #14 THHN (BLUE) LOAD SIDE CB TO LINE IMPEDANCE
W-1110 CB WEST LOAD PHASE A WEST LINE IMPEDANCE PHASE A #14 THHN (BLK) LOAD SIDE CB TO LINE IMPEDANCE
W-1111 CB WEST LOAD PHASE B WEST LINE IMPEDANCE PHASE B #14 THHN (RED) LOAD SIDE CB TO LINE IMPEDANCE
W-1112 CB WEST LOAD PHASE C WEST LINE IMPEDANCE PHASE C #14 THHN (BLUE) LOAD SIDE CB TO LINE IMPEDANCE
W-1113 EAST LINE IMPEDANCE PHASE A LOAD IMPEDANCE PHASE A #14 THHN (BLK) LINE IMPEDANCE TO LOAD
W-1114 EAST LINE IMPEDANCE PHASE B LOAD IMPEDANCE PHASE B #14 THHN (RED) LINE IMPEDANCE TO LOAD
W-1115 EAST LINE IMPEDANCE PHASE C LOAD IMPEDANCE PHASE C #14 THHN (BLUE) LINE IMPEDANCE TO LOAD
W-1116 WEST LINE IMPEDANCE PHASE A LOAD IMPEDANCE PHASE A #14 THHN (BLK) LINE IMPEDANCE TO LOAD
W-1117 WEST LINE IMPEDANCE PHASE B LOAD IMPEDANCE PHASE B #14 THHN (RED) LINE IMPEDANCE TO LOAD
W-1118 WEST LINE IMPEDANCE PHASE C LOAD IMPEDANCE PHASE C #14 THHN (BLUE) LINE IMPEDANCE TO LOAD
BANANA TERMINAL W-1119 LOAD PHASE A LOAD PHASE B #14 THHN (BLK) WYE LOAD CONNECTION
(TYP.) W-1120 LOAD PHASE B LOAD PHASE C #14 THHN (BLK) WYE LOAD CONNECTION
W-1121 SOURCE #1 IMPEDANCE PHASE A EAST LINE RELAY CURRENT PHASE A DOTTED #14 THHN (BLK) DOTTED TERMINAL
100mH INDUCTOR W-1122 SOURCE #1 IMPEDANCE PHASE B EAST LINE RELAY CURRENT PHASE B DOTTED #14 THHN (RED) DOTTED TERMINAL
W-1123 SOURCE #1 IMPEDANCE PHASE C EAST LINE RELAY CURRENT PHASE C DOTTED #14 THHN (BLUE) DOTTED TERMINAL
W-1124 EAST LINE RELAY CURRENT PHASE A EAST LINE INDUCTANCE PHASE A #14 THHN (BLK)
W-1125 EAST LINE RELAY CURRENT PHASE B EAST LINE INDUCTANCE PHASE B #14 THHN (RED)

LINE IMPEDANCE DETAIL W-1126

W-1127
EAST LINE RELAY CURRENT PHASE C
SOURCE #2 IMPEDANCE PHASE A
EAST LINE INDUCTANCE PHASE C
WEST LINE RELAY CURRENT PHASE A DOTTED
#14 THHN (BLUE)
#14 THHN (BLK) DOTTED TERMINAL
W-1128 SOURCE #2 IMPEDANCE PHASE B WEST LINE RELAY CURRENT PHASE B DOTTED #14 THHN (RED) DOTTED TERMINAL
SCALE: NONE
W-1129 SOURCE #2 IMPEDANCE PHASE C WEST LINE RELAY CURRENT PHASE C DOTTED #14 THHN (BLUE) DOTTED TERMINAL
W-1130 WEST LINE RELAY CURRENT PHASE A WEST LINE INDUCTANCE PHASE A #14 THHN (BLK)
W-1131 WEST LINE RELAY CURRENT PHASE B WEST LINE INDUCTANCE PHASE B #14 THHN (RED)
W-1132 WEST LINE RELAY CURRENT PHASE C WEST LINE INDUCTANCE PHASE C #14 THHN (BLUE)

SINGLE RESISTOR / INDUCTOR

REFER TO DRAWING
LOAD (3 TYP.) POTT_0151-03.DWG

W-1130

W-1127
TWIN RESISTOR / INDUCTOR REFER TO DRAWING
POTT_0151-03.DWG
LOAD (6 TYP.)
W-1121

W-1124

W-1116

CIRCUIT BREAKER
REFER TO DRAWING
POTT_0151-04.DWG
W-1113 W-1120 REFER TO DRAWING
POTT_0151-03.DWG

CIRCUIT BREAKER

W-1131

W-1128
REFER TO DRAWING
POTT_0151-04.DWG
REFER TO DRAWING
POTT_0151-03.DWG
W-1110 W-1104
W-1122

W-1125

W-1117 W-1111 W-1105 REFER TO DRAWING

POTT_0151-03.DWG
W-1112 W-1106

W-1101 W-1107

REFER TO DRAWING W-1102 W-1108 W-1114 REFER TO DRAWING

POTT_0151-03.DWG POTT_0151-03.DWG
W-1103 W-1109

W-1132

W-1129
REFER TO DRAWING
POTT_0151-03.DWG
W-1123

W-1126

W-1118

CIRCUIT BREAKER (2 TYP.) W-1115 W-1119

BOM
QTY: MANUFACTURER: PRODUCT: DESCRIPTION:
6 LAB EQUIPMENT TWIN RESISTOR & INDUCTOR LOAD
3 LAB EQUIPMENT SINGLE RESISTOR & INDUCTOR LOAD
2 LAB EQUIPMENT CIRCUIT BREAKER / FAULT BOXES

LABORATORY CIRCUIT WIRING DIAGRAM 50'

AR
SOUTHWIRE
IDEAL
#14 THHN WIRE BLK, RED, BLUE
#14-#24 RED NARROW FORK TERMINAL

SCALE: NONE
 NOTES
CIRCUIT BREAKER INSTRUCTIONS:

1. From source, connect phases to 'CB Line' connections

(CB-1007, CB-1008, and CB-1009.)

2. Connect the protected load to 'CB Load' connections (CB-1010,

CB-1011, and CB-1012.)

3. Connect a 125VDC source to 'Station Battery' terminals

(CB-1005, CB-1006.)

4. Connect protective relay output contacts (ex. SEL-311L

OUT101 and OUT102) to Normally Open (NO) output contacts
for 'CLOSE CB' (CB-1001, CB-1002) and Normally Closed
(NC) output contacts for 'TRIP CB' (CB-1003, CB-1004.)

5. Check Connections.

6. Energize 125VDC control circuit.

7. Test Breaker Manual Trip / Close functionality.

FAULT SIMULATOR CONFIGURATION:

1. De-energize equipment.

2. Connect 'Fault SW. Line' terminals to circuit nodes that are to

be faulted using banana leads.

3. Connect 'Fault SW. Load' terminals together in desired fault

DESCRIPTION: WIRE NUMBER: configurations (SLG, DLG, LL, LLL) using short leads. Example:
SEL OUTPUT NORMALLY OPEN (CLOSE CB) CB-1001 CB-1016 connected to CB-1017 for Line-to-Line fault across
SEL OUTPUT NORMALLY OPEN (CLOSE CB) Phase A and B.
CB-1002
SEL OUTPUT NORMALLY CLOSED (TRIP CB) CB-1003 4. Check Connections. Verify Fault Switch in Normal Position
SEL OUTPUT NORMALLY CLOSED (TRIP CB) CB-1004 (OFF). Energize Circuit. Toggle Fault Switch.
+125VDC STATION BATTERY CB-1005
0VDC (COMMON TERMINAL) STATION BATTERY CB-1006
CB LINE PHASE C CB-1007
CB LINE PHASE B CB-1008
CB LINE PHASE A CB-1009
CB LOAD PHASE A CB-1010
CB LOAD PHASE B CB-1011
CB LOAD PHASE C CB-1012
FAULT SW. LINE PHASE C CB-1013
FAULT SW. LINE PHASE B CB-1014
FAULT SW. LINE PHASE A CB-1015
FAULT SW. LOAD PHASE A CB-1016
FAULT SW. LOAD PHASE B CB-1017
FAULT SW. LOAD PHASE C CB-1018

CIRCUIT BREAKER WIRING DIAGRAM

SCALE: NONE
8.3 CIRCUIT BREAKER OPERATION

Circuit Breaker and Fault Simulator Connection Diagram

CIRCUIT BREAKER CONFIGURATION:

1. From source, connect phases to ‘CB Line’ connections (CB-1007, CB-1008, and CB-1009.)
2. Connect the protected load to ‘CB Load’ connections (CB-1010, CB-1011, and CB-1012.)
3. Connect a 125VDC source to ‘Station Battery’ terminals (CB-1005, CB-1006.)
4. Connect protective relay output contacts (ex. SEL-311L OUT101 and OUT102) to Normally Open (NO) output contacts for ‘CLOSE CB’
(CB-1001, CB-1002) and Normally Closed (NC) output contacts for ‘TRIP CB’ (CB-1003, CB-1004.)
5. Check Connections.
6. Energize 125VDC control circuit.
7. Test Breaker Manual Trip / Close functionality.

FAULT SIMULATOR CONFIGURATION:

1. De-energize equipment.
2. Connect ‘Fault SW. Line’ terminals to circuit nodes that are to be faulted using banana leads.
3. Connect ‘Fault SW. Load’ terminals together in desired fault configurations (SLG, DLG, LL, LLL) using short leads. Example: CB-1016
connected to CB-1017 for Line-to-Line fault across Phase A and B.
4. Check Connections. Verify Fault Switch in Normal Position (OFF). Energize Circuit. Toggle Fault Switch.

47 | P a g e
 SEL-311L EAST TRANSMISSION LINE

Setting Range Value

− Group : 1
f
e
g
RID Range = ASCII string with a maximum length of SEL-311
30.
TID Range = ASCII string with a maximum length of EXAMPLE: BUS B,
30. BREAKER 3
CTR Range = 1 to 6000 1
APP Select: 87L, 87L21, 87L21P, 87LSP, 311L 311L
EADVS Select: Y, N N
E87L Select: 2, 3, 3R, N 2
EHST Select: 1-6, N N
EHSDT Select: Y, N N
T
EDD Select: Y, N Y
ETAP Select: Y, N N
EOCTL Select: Y, N N
PCHAN Select: X, Y X
EHSC Select: Y, N N
CTR_X Range = 1 to 6000 1
TA_X Select: 1-16 1
RA_X Select: 1-16 2
CTR_Y Range = 1 to 6000 200
TA_Y Select: 1-16 3
RA_Y Select: 1-16 4
87LPP Range = 1.00 to 10.00, OFF 6.00
87L2P Range = 0.50 to 5.00, OFF 0.50
87LGP Range = 0.50 to 5.00, OFF OFF
CTALR Range = 0.50 to 10.00 0.50
M
87LR Range = 2.0 to 8.0 6.0
87LANG Range = 90 to 270 195

ETP Select: Y, N N
T51PP Range = 0.50 to 16.00, OFF OFF
T51PC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51PTD Range = 0.50 to 15.00 2.00

T51PRS Select: Y, N N

T50PP Range = 0.50 to 100.00, OFF OFF

T50PD Range = 0.00 to 16000.00, OFF 0.00
ETG Select: Y, N N
T51GP Range = 0.50 to 16.00, OFF 0.75

<Filter is Empty>

1 Of 16 5/20/2015 2:51 PM
Setting Range Value
T51GC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51GTD Range = 0.50 to 15.00 2.00

T51GRS Select: Y, N Y

T50GP Range = 0.50 to 100.00, OFF OFF

T50GD Range = 0.00 to 16000.00, OFF 0.00
ETQ Select: Y, N N
T51QP Range = 0.50 to 16.00, OFF 2.20
T51QC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51QT Range = 0.50 to 15.00 2.00

D
T51QRS Select: Y, N N

T50QP Range = 0.50 to 100.00, OFF OFF

T50QD Range = 0.00 to 16000.00, OFF 0.00
CTRP Range = 1 to 6000 1
PTR Range = 1.00 to 10000.00 1.00
PTRS Range = 1.00 to 10000.00 1.00
Z1MAG Range = 0.05 to 255.00 78.00
Z1ANG Range = 5.00 to 90.00 75.00
Z0MAG Range = 0.05 to 255.00 78.00
Z0ANG Range = 5.00 to 90.00 75.00
LL Range = 0.10 to 999.00 100.00
EFLOC Select: Y, N Y
E21P Select: N, 1-4, 1C-4C 2
ECCVT Select: Y, N N
Z1P Range = 0.05 to 64.00, OFF 40.00
Z2P Range = 0.05 to 64.00, OFF 60.00
Z3P Range = 0.05 to 64.00, OFF 1.87
Z4P Range = 0.05 to 64.00, OFF OFF
50PP1 Range = 0.50 to 170.00 0.50
50PP2 Range = 0.50 to 170.00 0.50
50PP3 Range = 0.50 to 170.00 0.50
50PP4 Range = 0.50 to 170.00 0.50
E21MG Select: N, 1-4 3
Z1MG Range = 0.05 to 64.00, OFF 40.00
Z2MG Range = 0.05 to 64.00, OFF 60.00
Z3MG Range = 0.05 to 64.00, OFF 60.00
Z4MG Range = 0.05 to 64.00, OFF OFF
E21XG Select: N, 1-4 N

<Filter is Empty>

2 Of 16 5/20/2015 2:51 PM
Setting Range Value
XG1 Range = 0.05 to 64.00, OFF 6.24
XG2 Range = 0.05 to 64.00, OFF 9.36
XG3 Range = 0.05 to 64.00, OFF 1.87
XG4 Range = 0.05 to 64.00, OFF OFF
RG1 Range = 0.05 to 50.00 2.50
RG2 Range = 0.05 to 50.00 5.00
RG3 Range = 0.05 to 50.00 6.00
RG4 Range = 0.05 to 50.00 0.05
XGPOL Select: I2, IG I2
TANG Range = -45.0 to 45.0 -3.0
50L1 Range = 0.50 to 100.00 0.50
50L2 Range = 0.50 to 100.00 0.50
50L3 Range = 0.50 to 100.00 0.50
50L4 Range = 0.50 to 100.00 0.50
50GZ1 Range = 0.50 to 100.00 0.50
50GZ2 Range = 0.50 to 100.00 0.50
50GZ3 Range = 0.50 to 100.00 0.50
50GZ4 Range = 0.50 to 100.00 0.50
k0M1 Range = 0.000 to 6.000 0.726
k0A1 Range = -180.00 to 180.00 -3.69
k0M Range = 0.000 to 6.000 0.726
k0A Range = -180.00 to 180.00 -3.69
Z1PD Range = 0.00 to 16000.00, OFF OFF
Z2PD Range = 0.00 to 16000.00, OFF 20.00
Z3PD Range = 0.00 to 16000.00, OFF OFF
Z4PD Range = 0.00 to 16000.00, OFF OFF
Z1GD Range = 0.00 to 16000.00, OFF OFF
Z2GD Range = 0.00 to 16000.00, OFF 20.00
Z3GD Range = 0.00 to 16000.00, OFF OFF
Z4GD Range = 0.00 to 16000.00, OFF OFF
Z1D Range = 0.00 to 16000.00, OFF OFF
Z2D Range = 0.00 to 16000.00, OFF OFF
Z3D Range = 0.00 to 16000.00, OFF OFF
Z4D Range = 0.00 to 16000.00, OFF OFF
E50P Select: N, 1-3 1
50P1P Range = 0.25 to 100.00, OFF 3.00
50P2P Range = 0.25 to 100.00, OFF OFF
50P3P Range = 0.25 to 100.00, OFF OFF
67P1D Range = 0.00 to 16000.00 0.00
67P2D Range = 0.00 to 16000.00 0.00
67P3D Range = 0.00 to 16000.00 0.00

<Filter is Empty>

3 Of 16 5/20/2015 2:51 PM
Setting Range Value
E50G Select: N, 1-4 N
50G1P Range = 0.25 to 100.00, OFF OFF
50G2P Range = 0.25 to 100.00, OFF OFF
50G3P Range = 0.25 to 100.00, OFF OFF
50G4P Range = 0.25 to 100.00, OFF OFF
67G1D Range = 0.00 to 16000.00 0.00
67G2D Range = 0.00 to 16000.00 0.00
67G3D Range = 0.00 to 16000.00 0.00
67G4D Range = 0.00 to 16000.00 0.00
E50Q Select: N, 1-4 N
50Q1P Range = 0.25 to 100.00, OFF OFF
50Q2P Range = 0.25 to 100.00, OFF OFF
50Q3P Range = 0.25 to 100.00, OFF OFF
50Q4P Range = 0.25 to 100.00, OFF OFF
67Q1D Range = 0.00 to 16000.00 0.00
67Q2D Range = 0.00 to 16000.00 0.00
67Q3D Range = 0.00 to 16000.00 0.00
67Q4D Range = 0.00 to 16000.00 0.00
E51P Select: Y, N N
51PP Range = 0.25 to 16.00, OFF OFF
51PC Select: U1-U5, C1-C5 U3
51PTD Range = 0.50 to 15.00 2.00
51PRS Select: Y, N N
E51G Select: Y, N Y
51GP Range = 0.25 to 16.00, OFF 0.75
51GC Select: U1-U5, C1-C5 U3
51GTD Range = 0.50 to 15.00 2.00
51GRS Select: Y, N Y
E51Q Select: Y, N Y
51QP Range = 0.25 to 16.00, OFF 2.20
51QC Select: U1-U5, C1-C5 U3
51QTD Range = 0.50 to 15.00 2.00
51QRS Select: Y, N N
EOOS Select: Y, N N
OOSB1 Select: Y, N N
OOSB2 Select: Y, N N
OOSB3 Select: Y, N N
OOSB4 Select: Y, N N
OSBD Range = 0.50 to 8000.00 2.00
EOOST Select: N, I, O N
OSTD Range = 0.50 to 8000.00 0.50

<Filter is Empty>

4 Of 16 5/20/2015 2:51 PM
Setting Range Value
X1T6 Range = 0.05 to 96.00 96.00
X1T5 Range = 0.05 to 96.00 90.00
R1R6 Range = 0.05 to 70.00 70.00
R1R5 Range = 0.05 to 70.00 65.00
X1B6 Range = -96.00 to -0.05 -96.00
X1B5 Range = -96.00 to -0.05 -90.00
R1L6 Range = -70.00 to -0.05 -70.00
R1L5 Range = -70.00 to -0.05 -65.00
50ABCP Range = 1.00 to 100.00 1.00

UBD Range = 0.50 to 120.00 0.50

UBOSBF Range = 1.00 to 10.00 4.00

ELOAD Select: Y, N Y
ZLF Range = 0.05 to 64.00 9.22
ZLR Range = 0.05 to 64.00 9.22
PLAF Range = -90.00 to 90.00 30.00
NLAF Range = -90.00 to 90.00 -30.00
PLAR Range = 90.00 to 270.00 150.00
NLAR Range = 90.00 to 270.00 210.00
E32 Select: Y, AUTO AUTO
ELOP Select: Y, Y1, N Y
EBBPT Select: Y, N N
DIR3 Select: F, R R
DIR4 Select: F, R F
ORDER Select: I, Q, V, OFF QVI
Z2F Range = -64.00 to 64.00 39.00
Z2R Range = -64.00 to 64.00 39.10
50QFP Range = 0.25 to 5.00 0.50
50QRP Range = 0.25 to 5.00 0.25
a2 Range = 0.02 to 0.50 0.10
k2 Range = 0.10 to 1.20 0.20
50GFP Range = 0.25 to 5.00 0.50
50GRP Range = 0.25 to 5.00 0.25
a0 Range = 0.02 to 0.50 0.10
Z0F Range = -64.00 to 64.00 39.00
Z0R Range = -64.00 to 64.00 39.10
EVOLT Select: Y, N N
27P Range = 0.00 to 150.00, OFF OFF
59P Range = 0.00 to 150.00, OFF OFF
59N1P Range = 0.00 to 150.00, OFF OFF
59N2P Range = 0.00 to 150.00, OFF OFF

<Filter is Empty>

5 Of 16 5/20/2015 2:51 PM
Setting Range Value
59QP Range = 0.00 to 100.00, OFF OFF
59V1P Range = 0.00 to 150.00, OFF OFF
27SP Range = 0.00 to 150.00, OFF OFF
59SP Range = 0.00 to 150.00, OFF OFF
27PP Range = 0.00 to 260.00, OFF OFF
59PP Range = 0.00 to 260.00, OFF OFF
E25 Select: Y, N N
25VLO Range = 0.00 to 150.00 60.00
25VHI Range = 0.00 to 150.00 75.00
25SF Range = 0.005 to 0.500 0.042
25ANG1 Range = 0.00 to 80.00 25.00

25ANG2 Range = 0.00 to 80.00 40.00

SYNCP Select: VA, VB, VC, VAB, VBC, VCA VA

TCLOSD Range = 1.00 to 60.00, OFF 3.00

E81 Select: N, 1-6 N

27B81P Range = 20.00 to 150.00 20.00

81D1P Range = 41.00 to 65.00, OFF OFF

81D1D Range = 2.00 to 16000.00 60.00
81D2P Range = 41.00 to 65.00, OFF OFF
81D2D Range = 2.00 to 16000.00 60.00
81D3P Range = 41.00 to 65.00, OFF OFF
81D3D Range = 2.00 to 16000.00 60.00
81D4P Range = 41.00 to 65.00, OFF OFF
81D4D Range = 2.00 to 16000.00 60.00
81D5P Range = 41.00 to 65.00, OFF OFF
81D5D Range = 2.00 to 16000.00 60.00
81D6P Range = 41.00 to 65.00, OFF OFF
81D6D Range = 2.00 to 16000.00 60.00
E79 Select: N, 1-4 N
79OI1 Range = 0.00 to 999999.00 0.00
79OI2 Range = 0.00 to 999999.00 0.00
79OI3 Range = 0.00 to 999999.00 0.00
79OI4 Range = 0.00 to 999999.00 0.00
79RSD Range = 0.00 to 999999.00 1800.00
79RSLD Range = 0.00 to 999999.00 300.00

79CLSD Range = 0.00 to 999999.00, OFF OFF

ESOTF Select: Y, N Y

<Filter is Empty>

6 Of 16 5/20/2015 2:51 PM
Setting Range Value
CLOEN Range = 0.00 to 16000.00, OFF OFF
D
52AEND Range = 0.00 to 16000.00, OFF 10.00

SOTFD Range = 0.50 to 16000.00 30.00

ECOMM Select: N, POTT, DCUB1, DCUB2, DCB POTT

Z3RBD Range = 0.00 to 16000.00 5.00

EBLKD Range = 0.00 to 16000.00, OFF 10.00
ETDPU Range = 0.00 to 16000.00, OFF 2.00
EDURD Range = 0.00 to 16000.00 4.00
EWFC Select: Y, N N
27PPW Range = 0.0 to 260.0 0.0
59NW Range = 0.0 to 150.0 150.0
GARD1 Range = 0.00 to 16000.00 10.00
D
UBDUR Range = 0.25 to 16000.00 9.00
D
UBEND Range = 0.00 to 16000.00 0.50
Z3XPU Range = 0.00 to 16000.00 1.00
Z3XD Range = 0.00 to 16000.00 5.00
BTXD Range = 0.00 to 16000.00 0.00
21SD Range = 0.00 to 60.00 1.00
67SD Range = 0.00 to 60.00 1.00
EMBA Select: Y, N N
RXIDA Range = 1 to 4 1
TXIDA Range = 1 to 4 2
EMBB Select: Y, N N
RXIDB Range = 1 to 4 1
TXIDB Range = 1 to 4 2
EZ1EXT Select: Y, N N

Z1EXTD Range = 0.00 to 16000.00 180.00

Z1EXTM Range = 1.00 to 4.00 1.30

EDEM Select: THM, ROL THM

DMTC Select: 5, 10, 15, 30, 60 60
PDEMP Range = 0.50 to 16.00, OFF OFF
GDEMP Range = 0.50 to 16.00, OFF OFF
QDEMP Range = 0.50 to 16.00, OFF OFF
TDURD Range = 2.00 to 16000.00 9.00
TOPD Range = 2.00 to 8000.00 2.00
CFD Range = 0.00 to 16000.00, OFF 60.00

<Filter is Empty>

7 Of 16 5/20/2015 2:51 PM
Setting Range Value
3POD Range = 0.00 to 60.00 0.50
OPO Select: 27, 52 52
27PO Range = 0.00 to 150.00 40.00
50LP Range = 0.25 to 100.00, OFF 0.25
ELAT Select: N, 1-16 16
EDP Select: N, 1-16 16
ESV Select: N, 1-16 N
SV1PU Range = 0.00 to 999999.00 0.00
SV2PU Range = 0.00 to 999999.00 0.00
SV3PU Range = 0.00 to 999999.00 0.00
SV4PU Range = 0.00 to 999999.00 0.00
SV5PU Range = 0.00 to 999999.00 0.00
SV6PU Range = 0.00 to 999999.00 0.00
SV7PU Range = 0.00 to 16000.00 0.00
SV8PU Range = 0.00 to 16000.00 0.00
SV9PU Range = 0.00 to 16000.00 0.00
SV10PU Range = 0.00 to 16000.00 0.00

SV11PU Range = 0.00 to 16000.00 0.00

SV12PU Range = 0.00 to 16000.00 0.00

SV13PU Range = 0.00 to 16000.00 0.00

SV14PU Range = 0.00 to 16000.00 0.00

SV15PU Range = 0.00 to 16000.00 0.00

SV16PU Range = 0.00 to 16000.00 0.00

SV1DO Range = 0.00 to 999999.00 0.00

SV2DO Range = 0.00 to 999999.00 0.00
SV3DO Range = 0.00 to 999999.00 0.00
SV4DO Range = 0.00 to 999999.00 0.00
SV5DO Range = 0.00 to 999999.00 0.00
SV6DO Range = 0.00 to 999999.00 0.00
SV7DO Range = 0.00 to 16000.00 0.00
SV8DO Range = 0.00 to 16000.00 0.00
SV9DO Range = 0.00 to 16000.00 0.00
SV10D Range = 0.00 to 16000.00 0.00
O
SV11D Range = 0.00 to 16000.00 0.00
O
SV12D Range = 0.00 to 16000.00 0.00
O

<Filter is Empty>

8 Of 16 5/20/2015 2:51 PM
Setting Range Value
SV13D Range = 0.00 to 16000.00 0.00
O
SV14D Range = 0.00 to 16000.00 0.00
O
SV15D Range = 0.00 to 16000.00 0.00
O
SV16D Range = 0.00 to 16000.00 0.00
O

+ Group : 2
g
f
e
+ Group : 3
g
f
e
+ Group : 4
f
e
g
+ Group : 5
f
e
g
+ Group : 6
g
f
e
+ Group : DNPA
g
f
e
+ Group : DNPB
f
e
g
+ Group : G
f
e
g
− Group : L1
g
f
e
TR Valid range = Boolean equation using word bit 87CHFAIL*(M1P+M
elements and the legal operators: ! / \ ( ) * + 2P+Z1G+Z2G)
TRCOM Valid range = Boolean equation using word bit M2P+Z2G
M elements and the legal operators: ! / \ ( ) * +
TRSOTF Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DTT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
E3PT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
ULTR Valid range = Boolean equation using word bit !(50L+51G)
elements and the legal operators: ! / \ ( ) * +
PT1 Valid range = Boolean equation using word bit R1X
elements and the legal operators: ! / \ ( ) * +
PT2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
LOG1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
LOG2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
BT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52A Valid range = Boolean equation using word bit IN101
elements and the legal operators: ! / \ ( ) * +
52AA Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52AB Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52AC Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
CL Valid range = Boolean equation using word bit CC
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

9 Of 16 5/20/2015 2:51 PM
Setting Range Value
ULCL Valid range = Boolean equation using word bit TRIP+TRIP87
elements and the legal operators: ! / \ ( ) * +
79RI Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79RIS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79DTL Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79DLS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79SKP Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79STL Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79BRS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79SEQ Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79CLS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

10 Of 16 5/20/2015 2:51 PM
Setting Range Value
SET16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
67P1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67P2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67P3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G4TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

11 Of 16 5/20/2015 2:51 PM
Setting Range Value
67Q2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q4TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
87LTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
SV1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

12 Of 16 5/20/2015 2:51 PM
Setting Range Value
SV13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT101 Valid range = Boolean equation using word bit
elements and the legal operators: ! / \ ( ) * +
OUT102 Valid range = Boolean equation using word bit CLOSE
elements and the legal operators: ! / \ ( ) * +
OUT103 Valid range = Boolean equation using word bit !TRIP*!OC
elements and the legal operators: ! / \ ( ) * +
OUT104 Valid range = Boolean equation using word bit
elements and the legal operators: ! / \ ( ) * +
OUT105 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT106 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT107 Valid range = Boolean equation using word bit 87HWAL
elements and the legal operators: ! / \ ( ) * +
OUT201 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT202 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT203 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT204 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT205 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT206 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT301 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT302 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT303 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT304 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT305 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT306 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT307 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT308 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

13 Of 16 5/20/2015 2:51 PM
Setting Range Value
OUT309 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT310 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT311 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT312 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP1 Valid range = Boolean equation using word bit 52A
elements and the legal operators: ! / \ ( ) * +
DP2 Valid range = Boolean equation using word bit CHXAL
elements and the legal operators: ! / \ ( ) * +
DP3 Valid range = Boolean equation using word bit CHYAL
elements and the legal operators: ! / \ ( ) * +
DP4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

14 Of 16 5/20/2015 2:51 PM
Setting Range Value
SS6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
ER Valid range = Boolean equation using word bit /B87L2+/M2P+/Z2
elements and the legal operators: ! / \ ( ) * + G+/51G+/51Q+/50
P1+/LOP
FAULT Valid range = Boolean equation using word bit 51G+51Q+M2P+Z2
elements and the legal operators: ! / \ ( ) * + G
BSYNC Valid range = Boolean equation using word bit 0
H elements and the legal operators: ! / \ ( ) * +
CLMON Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
BKMON Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
E32IV Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
ESTUB Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB1A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB2A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB3A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB4A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB5A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB6A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB7A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB8A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB1B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB2B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB3B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB4B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB5B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB6B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB7B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB8B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T1X Valid range = Boolean equation using word bit KEY
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

15 Of 16 5/20/2015 2:51 PM
Setting Range Value
T2X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T3X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T4X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T1Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T2Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T3Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T4Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

+ Group : L2
f
e
g
+ Group : L3
g
f
e
+ Group : L4
g
f
e
+ Group : L5
f
e
g
+ Group : L6
f
e
g
+ Group : P1
g
f
e
+ Group : P2
g
f
e
+ Group : P3
f
e
g
+ Group : P4
f
e
g
+ Group : P5
g
f
e
+ Group : R
g
f
e
+ Group : T
f
e
g
− Group : X
f
e
g
EADDC Select: Y, G, N Y
X
TA_X Select: 1-16 1
RA_X Select: 1-16 2
RBADXP Range = 1 to 1000 10

AVAXP Range = 1 to 5000 10

DBADX Range = 1 to 24 10
P
RC422X Select: R, F R

TC422X Select: R, F R

TIMRX Select: I, E E

+ Group : Y
f
e
g

<Filter is Empty>

16 Of 16 5/20/2015 2:51 PM
 SEL-311L WEST
TRANSMISSION LINE

Setting Range Value

− Group : 1
f
e
g
RID Range = ASCII string with a maximum length of SEL-311
30.
TID Range = ASCII string with a maximum length of EXAMPLE: BUS B,
30. BREAKER 3
CTR Range = 1 to 6000 1
APP Select: 87L, 87L21, 87L21P, 87LSP, 311L 311L
EADVS Select: Y, N N
E87L Select: 2, 3, 3R, N 2
EHST Select: 1-6, N N
EHSDT Select: Y, N N
T
EDD Select: Y, N Y
ETAP Select: Y, N N
EOCTL Select: Y, N N
PCHAN Select: X, Y X
EHSC Select: Y, N N
CTR_X Range = 1 to 6000 1
TA_X Select: 1-16 1
RA_X Select: 1-16 2
CTR_Y Range = 1 to 6000 200
TA_Y Select: 1-16 3
RA_Y Select: 1-16 4
87LPP Range = 1.00 to 10.00, OFF 6.00
87L2P Range = 0.50 to 5.00, OFF 0.50
87LGP Range = 0.50 to 5.00, OFF OFF
CTALR Range = 0.50 to 10.00 0.50
M
87LR Range = 2.0 to 8.0 6.0
87LANG Range = 90 to 270 195

ETP Select: Y, N N
T51PP Range = 0.50 to 16.00, OFF OFF
T51PC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51PTD Range = 0.50 to 15.00 2.00

T51PRS Select: Y, N N

T50PP Range = 0.50 to 100.00, OFF OFF

T50PD Range = 0.00 to 16000.00, OFF 0.00
ETG Select: Y, N N

<Filter is Empty>

1 Of 16 5/20/2015 2:58 PM
Setting Range Value
T51GP Range = 0.50 to 16.00, OFF 0.75
T51GC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51GTD Range = 0.50 to 15.00 2.00

T51GRS Select: Y, N Y

T50GP Range = 0.50 to 100.00, OFF OFF

T50GD Range = 0.00 to 16000.00, OFF 0.00
ETQ Select: Y, N N
T51QP Range = 0.50 to 16.00, OFF 2.20
T51QC Select: U1, U2, U3, U4, U5, C1, C2, C3, C4, C5 U3

T51QT Range = 0.50 to 15.00 2.00

D
T51QRS Select: Y, N N

T50QP Range = 0.50 to 100.00, OFF OFF

T50QD Range = 0.00 to 16000.00, OFF 0.00
CTRP Range = 1 to 6000 1
PTR Range = 1.00 to 10000.00 1.00
PTRS Range = 1.00 to 10000.00 1.00
Z1MAG Range = 0.05 to 255.00 78.00
Z1ANG Range = 5.00 to 90.00 75.00
Z0MAG Range = 0.05 to 255.00 78.00
Z0ANG Range = 5.00 to 90.00 75.00
LL Range = 0.10 to 999.00 100.00
EFLOC Select: Y, N Y
E21P Select: N, 1-4, 1C-4C 2
ECCVT Select: Y, N N
Z1P Range = 0.05 to 64.00, OFF 40.00
Z2P Range = 0.05 to 64.00, OFF 60.00
Z3P Range = 0.05 to 64.00, OFF 1.87
Z4P Range = 0.05 to 64.00, OFF OFF
50PP1 Range = 0.50 to 170.00 0.50
50PP2 Range = 0.50 to 170.00 0.50
50PP3 Range = 0.50 to 170.00 0.50
50PP4 Range = 0.50 to 170.00 0.50
E21MG Select: N, 1-4 3
Z1MG Range = 0.05 to 64.00, OFF 40.00
Z2MG Range = 0.05 to 64.00, OFF 60.00
Z3MG Range = 0.05 to 64.00, OFF 60.00
Z4MG Range = 0.05 to 64.00, OFF OFF

<Filter is Empty>

2 Of 16 5/20/2015 2:58 PM
Setting Range Value
E21XG Select: N, 1-4 N
XG1 Range = 0.05 to 64.00, OFF 6.24
XG2 Range = 0.05 to 64.00, OFF 9.36
XG3 Range = 0.05 to 64.00, OFF 1.87
XG4 Range = 0.05 to 64.00, OFF OFF
RG1 Range = 0.05 to 50.00 2.50
RG2 Range = 0.05 to 50.00 5.00
RG3 Range = 0.05 to 50.00 6.00
RG4 Range = 0.05 to 50.00 0.05
XGPOL Select: I2, IG I2
TANG Range = -45.0 to 45.0 -3.0
50L1 Range = 0.50 to 100.00 0.50
50L2 Range = 0.50 to 100.00 0.50
50L3 Range = 0.50 to 100.00 0.50
50L4 Range = 0.50 to 100.00 0.50
50GZ1 Range = 0.50 to 100.00 0.50
50GZ2 Range = 0.50 to 100.00 0.50
50GZ3 Range = 0.50 to 100.00 0.50
50GZ4 Range = 0.50 to 100.00 0.50
k0M1 Range = 0.000 to 6.000 0.726
k0A1 Range = -180.00 to 180.00 -3.69
k0M Range = 0.000 to 6.000 0.726
k0A Range = -180.00 to 180.00 -3.69
Z1PD Range = 0.00 to 16000.00, OFF OFF
Z2PD Range = 0.00 to 16000.00, OFF 20.00
Z3PD Range = 0.00 to 16000.00, OFF OFF
Z4PD Range = 0.00 to 16000.00, OFF OFF
Z1GD Range = 0.00 to 16000.00, OFF OFF
Z2GD Range = 0.00 to 16000.00, OFF 20.00
Z3GD Range = 0.00 to 16000.00, OFF OFF
Z4GD Range = 0.00 to 16000.00, OFF OFF
Z1D Range = 0.00 to 16000.00, OFF OFF
Z2D Range = 0.00 to 16000.00, OFF OFF
Z3D Range = 0.00 to 16000.00, OFF OFF
Z4D Range = 0.00 to 16000.00, OFF OFF
E50P Select: N, 1-3 1
50P1P Range = 0.25 to 100.00, OFF 3.00
50P2P Range = 0.25 to 100.00, OFF OFF
50P3P Range = 0.25 to 100.00, OFF OFF
67P1D Range = 0.00 to 16000.00 0.00
67P2D Range = 0.00 to 16000.00 0.00

<Filter is Empty>

3 Of 16 5/20/2015 2:58 PM
Setting Range Value
67P3D Range = 0.00 to 16000.00 0.00
E50G Select: N, 1-4 N
50G1P Range = 0.25 to 100.00, OFF OFF
50G2P Range = 0.25 to 100.00, OFF OFF
50G3P Range = 0.25 to 100.00, OFF OFF
50G4P Range = 0.25 to 100.00, OFF OFF
67G1D Range = 0.00 to 16000.00 0.00
67G2D Range = 0.00 to 16000.00 0.00
67G3D Range = 0.00 to 16000.00 0.00
67G4D Range = 0.00 to 16000.00 0.00
E50Q Select: N, 1-4 N
50Q1P Range = 0.25 to 100.00, OFF OFF
50Q2P Range = 0.25 to 100.00, OFF OFF
50Q3P Range = 0.25 to 100.00, OFF OFF
50Q4P Range = 0.25 to 100.00, OFF OFF
67Q1D Range = 0.00 to 16000.00 0.00
67Q2D Range = 0.00 to 16000.00 0.00
67Q3D Range = 0.00 to 16000.00 0.00
67Q4D Range = 0.00 to 16000.00 0.00
E51P Select: Y, N N
51PP Range = 0.25 to 16.00, OFF OFF
51PC Select: U1-U5, C1-C5 U3
51PTD Range = 0.50 to 15.00 2.00
51PRS Select: Y, N N
E51G Select: Y, N Y
51GP Range = 0.25 to 16.00, OFF 0.75
51GC Select: U1-U5, C1-C5 U3
51GTD Range = 0.50 to 15.00 2.00
51GRS Select: Y, N Y
E51Q Select: Y, N Y
51QP Range = 0.25 to 16.00, OFF 2.20
51QC Select: U1-U5, C1-C5 U3
51QTD Range = 0.50 to 15.00 2.00
51QRS Select: Y, N N
EOOS Select: Y, N N
OOSB1 Select: Y, N N
OOSB2 Select: Y, N N
OOSB3 Select: Y, N N
OOSB4 Select: Y, N N
OSBD Range = 0.50 to 8000.00 2.00
EOOST Select: N, I, O N

<Filter is Empty>

4 Of 16 5/20/2015 2:58 PM
Setting Range Value
OSTD Range = 0.50 to 8000.00 0.50
X1T6 Range = 0.05 to 96.00 96.00
X1T5 Range = 0.05 to 96.00 90.00
R1R6 Range = 0.05 to 70.00 70.00
R1R5 Range = 0.05 to 70.00 65.00
X1B6 Range = -96.00 to -0.05 -96.00
X1B5 Range = -96.00 to -0.05 -90.00
R1L6 Range = -70.00 to -0.05 -70.00
R1L5 Range = -70.00 to -0.05 -65.00
50ABCP Range = 1.00 to 100.00 1.00

UBD Range = 0.50 to 120.00 0.50

UBOSBF Range = 1.00 to 10.00 4.00

ELOAD Select: Y, N Y
ZLF Range = 0.05 to 64.00 9.22
ZLR Range = 0.05 to 64.00 9.22
PLAF Range = -90.00 to 90.00 30.00
NLAF Range = -90.00 to 90.00 -30.00
PLAR Range = 90.00 to 270.00 150.00
NLAR Range = 90.00 to 270.00 210.00
E32 Select: Y, AUTO AUTO
ELOP Select: Y, Y1, N Y
EBBPT Select: Y, N N
DIR3 Select: F, R R
DIR4 Select: F, R F
ORDER Select: I, Q, V, OFF QVI
Z2F Range = -64.00 to 64.00 39.00
Z2R Range = -64.00 to 64.00 39.10
50QFP Range = 0.25 to 5.00 0.50
50QRP Range = 0.25 to 5.00 0.25
a2 Range = 0.02 to 0.50 0.10
k2 Range = 0.10 to 1.20 0.20
50GFP Range = 0.25 to 5.00 0.50
50GRP Range = 0.25 to 5.00 0.25
a0 Range = 0.02 to 0.50 0.10
Z0F Range = -64.00 to 64.00 39.00
Z0R Range = -64.00 to 64.00 39.10
EVOLT Select: Y, N N
27P Range = 0.00 to 150.00, OFF OFF
59P Range = 0.00 to 150.00, OFF OFF
59N1P Range = 0.00 to 150.00, OFF OFF

<Filter is Empty>

5 Of 16 5/20/2015 2:58 PM
Setting Range Value
59N2P Range = 0.00 to 150.00, OFF OFF
59QP Range = 0.00 to 100.00, OFF OFF
59V1P Range = 0.00 to 150.00, OFF OFF
27SP Range = 0.00 to 150.00, OFF OFF
59SP Range = 0.00 to 150.00, OFF OFF
27PP Range = 0.00 to 260.00, OFF OFF
59PP Range = 0.00 to 260.00, OFF OFF
E25 Select: Y, N N
25VLO Range = 0.00 to 150.00 60.00
25VHI Range = 0.00 to 150.00 75.00
25SF Range = 0.005 to 0.500 0.042
25ANG1 Range = 0.00 to 80.00 25.00

25ANG2 Range = 0.00 to 80.00 40.00

SYNCP Select: VA, VB, VC, VAB, VBC, VCA VA

TCLOSD Range = 1.00 to 60.00, OFF 3.00

E81 Select: N, 1-6 N

27B81P Range = 20.00 to 150.00 20.00

81D1P Range = 41.00 to 65.00, OFF OFF

81D1D Range = 2.00 to 16000.00 60.00
81D2P Range = 41.00 to 65.00, OFF OFF
81D2D Range = 2.00 to 16000.00 60.00
81D3P Range = 41.00 to 65.00, OFF OFF
81D3D Range = 2.00 to 16000.00 60.00
81D4P Range = 41.00 to 65.00, OFF OFF
81D4D Range = 2.00 to 16000.00 60.00
81D5P Range = 41.00 to 65.00, OFF OFF
81D5D Range = 2.00 to 16000.00 60.00
81D6P Range = 41.00 to 65.00, OFF OFF
81D6D Range = 2.00 to 16000.00 60.00
E79 Select: N, 1-4 N
79OI1 Range = 0.00 to 999999.00 0.00
79OI2 Range = 0.00 to 999999.00 0.00
79OI3 Range = 0.00 to 999999.00 0.00
79OI4 Range = 0.00 to 999999.00 0.00
79RSD Range = 0.00 to 999999.00 1800.00
79RSLD Range = 0.00 to 999999.00 300.00

79CLSD Range = 0.00 to 999999.00, OFF OFF

<Filter is Empty>

6 Of 16 5/20/2015 2:58 PM
Setting Range Value
ESOTF Select: Y, N Y
CLOEN Range = 0.00 to 16000.00, OFF OFF
D
52AEND Range = 0.00 to 16000.00, OFF 10.00

SOTFD Range = 0.50 to 16000.00 30.00

ECOMM Select: N, POTT, DCUB1, DCUB2, DCB POTT

Z3RBD Range = 0.00 to 16000.00 5.00

EBLKD Range = 0.00 to 16000.00, OFF 10.00
ETDPU Range = 0.00 to 16000.00, OFF 2.00
EDURD Range = 0.00 to 16000.00 4.00
EWFC Select: Y, N N
27PPW Range = 0.0 to 260.0 0.0
59NW Range = 0.0 to 150.0 150.0
GARD1 Range = 0.00 to 16000.00 10.00
D
UBDUR Range = 0.25 to 16000.00 9.00
D
UBEND Range = 0.00 to 16000.00 0.50
Z3XPU Range = 0.00 to 16000.00 1.00
Z3XD Range = 0.00 to 16000.00 5.00
BTXD Range = 0.00 to 16000.00 0.00
21SD Range = 0.00 to 60.00 1.00
67SD Range = 0.00 to 60.00 1.00
EMBA Select: Y, N N
RXIDA Range = 1 to 4 1
TXIDA Range = 1 to 4 2
EMBB Select: Y, N N
RXIDB Range = 1 to 4 1
TXIDB Range = 1 to 4 2
EZ1EXT Select: Y, N N

Z1EXTD Range = 0.00 to 16000.00 180.00

Z1EXTM Range = 1.00 to 4.00 1.30

EDEM Select: THM, ROL THM

DMTC Select: 5, 10, 15, 30, 60 60
PDEMP Range = 0.50 to 16.00, OFF OFF
GDEMP Range = 0.50 to 16.00, OFF OFF
QDEMP Range = 0.50 to 16.00, OFF OFF
TDURD Range = 2.00 to 16000.00 9.00
TOPD Range = 2.00 to 8000.00 2.00

<Filter is Empty>

7 Of 16 5/20/2015 2:58 PM
Setting Range Value
CFD Range = 0.00 to 16000.00, OFF 60.00
3POD Range = 0.00 to 60.00 0.50
OPO Select: 27, 52 52
27PO Range = 0.00 to 150.00 40.00
50LP Range = 0.25 to 100.00, OFF 0.25
ELAT Select: N, 1-16 16
EDP Select: N, 1-16 16
ESV Select: N, 1-16 N
SV1PU Range = 0.00 to 999999.00 0.00
SV2PU Range = 0.00 to 999999.00 0.00
SV3PU Range = 0.00 to 999999.00 0.00
SV4PU Range = 0.00 to 999999.00 0.00
SV5PU Range = 0.00 to 999999.00 0.00
SV6PU Range = 0.00 to 999999.00 0.00
SV7PU Range = 0.00 to 16000.00 0.00
SV8PU Range = 0.00 to 16000.00 0.00
SV9PU Range = 0.00 to 16000.00 0.00
SV10PU Range = 0.00 to 16000.00 0.00

SV11PU Range = 0.00 to 16000.00 0.00

SV12PU Range = 0.00 to 16000.00 0.00

SV13PU Range = 0.00 to 16000.00 0.00

SV14PU Range = 0.00 to 16000.00 0.00

SV15PU Range = 0.00 to 16000.00 0.00

SV16PU Range = 0.00 to 16000.00 0.00

SV1DO Range = 0.00 to 999999.00 0.00

SV2DO Range = 0.00 to 999999.00 0.00
SV3DO Range = 0.00 to 999999.00 0.00
SV4DO Range = 0.00 to 999999.00 0.00
SV5DO Range = 0.00 to 999999.00 0.00
SV6DO Range = 0.00 to 999999.00 0.00
SV7DO Range = 0.00 to 16000.00 0.00
SV8DO Range = 0.00 to 16000.00 0.00
SV9DO Range = 0.00 to 16000.00 0.00
SV10D Range = 0.00 to 16000.00 0.00
O
SV11D Range = 0.00 to 16000.00 0.00
O

<Filter is Empty>

8 Of 16 5/20/2015 2:58 PM
Setting Range Value
SV12D Range = 0.00 to 16000.00 0.00
O
SV13D Range = 0.00 to 16000.00 0.00
O
SV14D Range = 0.00 to 16000.00 0.00
O
SV15D Range = 0.00 to 16000.00 0.00
O
SV16D Range = 0.00 to 16000.00 0.00
O

+ Group : 2
f
e
g
+ Group : 3
f
e
g
+ Group : 4
g
f
e
+ Group : 5
g
f
e
+ Group : 6
f
e
g
+ Group : DNPA
f
e
g
+ Group : DNPB
g
f
e
+ Group : G
g
f
e
− Group : L1
f
e
g
TR Valid range = Boolean equation using word bit 87CHFAIL*(M1P+M
elements and the legal operators: ! / \ ( ) * + 2P+Z1G+Z2G)
TRCOM Valid range = Boolean equation using word bit M2P+Z2G
M elements and the legal operators: ! / \ ( ) * +
TRSOTF Valid range = Boolean equation using word bit M2P
elements and the legal operators: ! / \ ( ) * +
DTT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
E3PT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
ULTR Valid range = Boolean equation using word bit !(50L+51G)
elements and the legal operators: ! / \ ( ) * +
PT1 Valid range = Boolean equation using word bit R1X
elements and the legal operators: ! / \ ( ) * +
PT2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
LOG1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
LOG2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
BT Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52A Valid range = Boolean equation using word bit IN101
elements and the legal operators: ! / \ ( ) * +
52AA Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52AB Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
52AC Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

9 Of 16 5/20/2015 2:58 PM
Setting Range Value
CL Valid range = Boolean equation using word bit CC
elements and the legal operators: ! / \ ( ) * +
ULCL Valid range = Boolean equation using word bit TRIP+TRIP87
elements and the legal operators: ! / \ ( ) * +
79RI Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79RIS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79DTL Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79DLS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79SKP Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79STL Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79BRS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79SEQ Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
79CLS Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

10 Of 16 5/20/2015 2:58 PM
Setting Range Value
SET15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SET16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
RST16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
67P1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67P2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67P3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67G4TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

11 Of 16 5/20/2015 2:58 PM
Setting Range Value
67Q1TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q2TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q3TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
67Q4TC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
51QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T51QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50PTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50GTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
T50QTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
87LTC Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
SV1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

12 Of 16 5/20/2015 2:58 PM
Setting Range Value
SV12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SV16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT101 Valid range = Boolean equation using word bit
elements and the legal operators: ! / \ ( ) * +
OUT102 Valid range = Boolean equation using word bit CLOSE
elements and the legal operators: ! / \ ( ) * +
OUT103 Valid range = Boolean equation using word bit !TRIP*!OC
elements and the legal operators: ! / \ ( ) * +
OUT104 Valid range = Boolean equation using word bit
elements and the legal operators: ! / \ ( ) * +
OUT105 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT106 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT107 Valid range = Boolean equation using word bit 87HWAL
elements and the legal operators: ! / \ ( ) * +
OUT201 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT202 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT203 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT204 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT205 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT206 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT301 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT302 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT303 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT304 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT305 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT306 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT307 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

13 Of 16 5/20/2015 2:58 PM
Setting Range Value
OUT308 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT309 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT310 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT311 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
OUT312 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP1 Valid range = Boolean equation using word bit 52A
elements and the legal operators: ! / \ ( ) * +
DP2 Valid range = Boolean equation using word bit CHXAL
elements and the legal operators: ! / \ ( ) * +
DP3 Valid range = Boolean equation using word bit CHYAL
elements and the legal operators: ! / \ ( ) * +
DP4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP7 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP8 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP9 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP10 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP11 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP12 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP13 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP14 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP15 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
DP16 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS1 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS2 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS3 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS4 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

14 Of 16 5/20/2015 2:58 PM
Setting Range Value
SS5 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
SS6 Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
ER Valid range = Boolean equation using word bit /B87L2+/M2P+/Z2
elements and the legal operators: ! / \ ( ) * + G+/51G+/51Q+/50
P1+/LOP
FAULT Valid range = Boolean equation using word bit 51G+51Q+M2P+Z2
elements and the legal operators: ! / \ ( ) * + G
BSYNC Valid range = Boolean equation using word bit 0
H elements and the legal operators: ! / \ ( ) * +
CLMON Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
BKMON Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
E32IV Valid range = Boolean equation using word bit 1
elements and the legal operators: ! / \ ( ) * +
ESTUB Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB1A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB2A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB3A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB4A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB5A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB6A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB7A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB8A Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB1B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB2B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB3B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB4B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB5B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB6B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB7B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
TMB8B Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

<Filter is Empty>

15 Of 16 5/20/2015 2:58 PM
Setting Range Value
T1X Valid range = Boolean equation using word bit KEY
elements and the legal operators: ! / \ ( ) * +
T2X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T3X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T4X Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T1Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T2Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T3Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +
T4Y Valid range = Boolean equation using word bit 0
elements and the legal operators: ! / \ ( ) * +

+ Group : L2
f
e
g
+ Group : L3
f
e
g
+ Group : L4
g
f
e
+ Group : L5
g
f
e
+ Group : L6
f
e
g
+ Group : P1
f
e
g
+ Group : P2
g
f
e
+ Group : P3
g
f
e
+ Group : P4
f
e
g
+ Group : P5
f
e
g
+ Group : R
g
f
e
+ Group : T
g
f
e
− Group : X
f
e
g
EADDC Select: Y, G, N Y
X
TA_X Select: 1-16 2
RA_X Select: 1-16 1
RBADXP Range = 1 to 1000 10

AVAXP Range = 1 to 5000 10

DBADX Range = 1 to 24 10
P
RC422X Select: R, F R

TC422X Select: R, F R

TIMRX Select: I, E I

+ Group : Y
g
f
e

<Filter is Empty>

16 Of 16 5/20/2015 2:58 PM
8.4 SEL 311-L PILOT PROTECTION LABORATORY MANUAL

PAGE INTENTIONALLY LEFT BLANK

 ELECTRICAL ENGINEERING DEPARTMENT
California Polytechnic State University
EE 444 Experiment #
Permissive Over-reaching Transfer Trip Protection (POTT)
Introduction:
Permissive Over-reaching Transfer Trip Protection (POTT) is a communication based protection
scheme that relies on phase distance protection elements. Protection of transmission lines in a non-
radial systems is difficult to coordinate with other connected transmission lines and distribution
because power flow is not static or in one direction all of the time. For the protection of
transmission lines, differential protection is not possible because of the losses along the line (Iin≠
Iout). The basic topology of the system consists of a transmission line with a SEL-311L relay at each
end connected via a fiber optic communications line. The relays phase distance Zone 2 elements are
set to pick-up at 120% of the line. The difference between phase distance and POTT is in the trip
logic and communications link. A trip will only be issued if both relays Zone 2 elements pick-up and
both of the relays receive a “key” from the other acknowledging that they too could see the Zone 2
Fault. The logic can be better explained by referring to the logic diagram below in Figure 1.

Figure 1. POTT Trip Logic

EQUIPMENT:
2 SEL 311-L relays
2 Circuit breakers
6 Inductor / double power resistors boards (100mH+ (2) 10Ω)
35 Long banana-to banana leads
1 Bag of short leads
1 Multi-meter
1 SEL serial data cable

49 | P a g e
3 High resistance / impedance load
PROCEDURE:
1. Download and print the construction document set.
2. Using banana to banana leads, wire the system according to the wiring diagrams in the construction
drawing set.
3. With the power off, test the systems resistance of each phase to the center of the load wye
connection. Resistance values should be 20 ohms + (load resistance / impedance) disconnected from
the sources for resistance from each phase.
4. With the power off, verify the resistance between phases at the source is greater than 20 ohms.
a. A to B
b. B to C
c. C to A
5. Wire Breaker and connect breaker to the SEL relay as shown in the construction drawing set.
6. Test manual breaker functionality by only energizing the 125VDC and pressing Open/ Close to
verify breaker operation.
7. Program relay using settings found in the appendix of this document.
8. Upload the settings following the directions found in the appendix.
9. Based on the Single Line drawing in the construction drawing set. Connect the fault switch to the
nodes internal to the transmission line zone of protection.
10. Apply fault conditions based on the procedure outlined in the “Breaker Operation” section. The
fault switch should only be turned on momentarily. The switch should be returned to the off
position within 5 seconds of being turned on to prevent equipment overheating and damage.
11. Apply SLG, LL, LLL faults for internal faults only. Download and view events to AcSELerator
Analytic Assistant.

50 | P a g e
APPENDIX:
The relay settings below should be edited to provide proper system POTT protection.
Step 1. Open AcSELerator
Step 2. Click File new and choose SEL311-L. Based on the serial number of your relay enter the
required information.
Step 3. Connect serial cable to the serial port located on the front of the relay and to the lab bench
desktop
Step 4. Under the communications menu, select parameters. Confirm that the active connection type
is set to serial and the settings in Figure 2 have been selected.

Figure 2. Communications Settings

Step 5. Click Connect. The bottom right hand corner of the window should display “Connected.”
Step 6. Edit Settings.

Step 7. Click Send Active settings button.

51 | P a g e
Figure 3. Line Current Differential Settings

Figure 4. 87L Transmit Equations

52 | P a g e
Figure 5. Close/Reclose Logic

Figure 6. Phase Distance

53 | P a g e
Figure 7. Trip/Comm – Assisted Trip Logic

54 | P a g e
Figure 8. Output Contacts

55 | P a g e
8.5 REFERENCES

[1] J. L. Blackburn, and T. J. Domin, Protective Relaying Principles and Applications 4th
Edition. Boca Raton, FL: Taylor & Francis Group, LLC, 2014.

[2] Schweitzer Engineering Laboratories, SEL-311L-1 -7 Relay Protection and Automation

System Instruction Manual, Pullman, Washington: Schweitzer Engineering Laboratories, 2003-2014.

[3] IEEE Guide for Developing System Requirements Specifications," IEEE Std 1233-1996 ,
vol., no., pp.i,, 1996 doi: 10.1109/IEEESTD.1996.81000

[4] Schweitzer Engineering Laboratories, “SEL-311L Line Current Differential Protection and
Automation System (Data Sheet),” Schweitzer Engineering Laboratories. [Online]. Available:
https://www.selinc.com/SEL-311L/ [Accessed: Jan, 22, 2015]

[4] Bogdan Z. Kasztenny, Normann Fischer, "Transformer differential protection,“ U.S. Patent:
8 553 379, issued date October 8, 2013. Available: http://patft1.uspto.gov/netacgi/nph-
Parser?patentnumber=8553379

[5] Schweitzer Engineering Laboratories, “SEL-2032 Communications Processor Instruction

Manual,” Schweitzer Engineering Laboratories. [Online]. Available: https://www.selinc.com/SEL-
2032/ [Accessed: Jan, 22, 2015]

[6] IEEE Recommended Practice for Industrial and Commercial Power System Analysis,"
IEEE Std 399-1990 , vol., no., pp.1,384, Dec. 15 1990

[7] IEEE Guide for Protective Relay Applications to Transmission Lines," IEEE Std C37.113-
1999 , vol., no., pp.i,, 2000

[8] Ghanizadeh Bolandi, T.; Seyedi, H.; Hashemi, S.M.; Soleiman Nezhad, P., "Impedance-
Differential Protection: A New Approach to Transmission-Line Pilot Protection," Power Delivery,
IEEE Transactions on , vol.PP, no.99, pp.1,1

[9] IEEE Guide for Protecting Power Transformers," IEEE Std C37.91-2008 (Revision of
IEEE Std C37.91-2000) , vol., no., pp.1,139, May 30 2008

doi: 10.1109/IEEESTD.2008.4534870

56 | P a g e
[10] IEEE Guide for Determining Fault Location on AC Transmission and Distribution Lines,"
IEEE Std C37.114-2014 (Revision of IEEE Std C37.114-2004) , vol., no., pp.1,76, Jan. 30 2015

57 | P a g e