H 100 Manual

OWNER'S MANUAL
Operation
Maintenance
Specifications
All information in the Owner's Manual is current at the time of publication.

HYUNDAI reserves the right to make changes at any time as part of our pol-
icy of continual product improvement may be carried out.
This manual applies to current HYUNDAI models of this vehicle and expla-
nations of optional as well as standard equipment are included. As a result,
you may find material in this manual that does not apply to your specific
vehicle.
Please note that some models are equipped with Right-Hand Drive (RHD).
The explanations and illustrations for some operations in RHD models are
opposite of those written in this manual.
CAUTION: MODIFICATIONS TO YOUR HYUNDAI
Modification of components may void the manufacturer's warranty
Your HYUNDAI should not be modified in any way. Modifications may adversely affect the safety, durabil-
ity and performance of your HYUNDAI. Components which are subjected to modification or are added to
the vehicle resulting in consequential damage are not covered by the vehicle manufacturer's warranty.
TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION

Your vehicle is equipped with electronic fuel injection and other electronic components. It is possible
for an improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic
systems. For this reason, we recommend that you carefully follow the radio manufacturer's instruc-
tions or consult your HYUNDAI dealer for precautionary measures or special instructions if you
choose to install one of these devices.
F2
SAFETY AND VEHICLE DAMAGE WARNING
This manual includes information titled as WARNING, CAUTION and NOTICE.

These titles indicate the following:
WARNING
This indicates that a condition may result in harm, serious injury or death to you or other
persons if the warning is not heeded. Follow the advice provided with the warning.
CAUTION
This indicates that a condition may result in damage to your vehicle or its equipment if the
caution is not heeded. Follow the advice provided with the caution.
✽ NOTICE
This indicates that interesting or helpful information is being provided.
F3
FOREWORD
Thank you for choosing HYUNDAI. We are pleased to welcome you to the growing number of discriminating people who drive
HYUNDAIs. The advanced engineering and high-quality construction of each HYUNDAI we build is something of which we're very
proud.
Your Owner's Manual will introduce you to the features and operation of your new HYUNDAI. It is suggested that you read it care-
fully because the information it contains can contribute greatly to the satisfaction you receive from your new car.
The manufacturer also recommends that all service and maintenance on your car be performed by an authorized HYUNDAI dealer.
HYUNDAI dealers are prepared to provide high-quality service, maintenance and any other assistance that may be required.
HYUNDAI MOTOR COMPANY
Note : Because future owners will also need the information included in this manual, if you sell this HYUNDAI, please leave the
manual in the vehicle for their use. Thank you.
CAUTION
Severe engine and transmission damage may result from the use of poor quality fuels and lubricants that do not meet
HYUNDAI specifications. You must always use high quality fuels and lubricants that meet the specifications listed on Page
9-4 in the Vehicle Specifications section of the Owner's Manual.
Copyright 2017 HYUNDAI Motor Company. All rights reserved. No part of this publication may be reproduced, stored in any
retrieval system or transmitted in any form or by any means without the prior written permission of HYUNDAI Motor Company.
F4
Guide to HYUNDAI Genuine Parts 2. Why should you use genuine 3. How can you tell if you are purchas-
1. What are HYUNDAI Genuine Parts? parts? ing HYUNDAI Genuine Parts?
HYUNDAI Genuine Parts are the same HYUNDAI Genuine Parts are engi- Look for the HYUNDAI Genuine Parts
parts used by HYUNDAI Motor neered and built to meet rigid manu- Logo on the package (see below).
Company to manufacture vehicles. facturing requirements. Using imita- HYUNDAI Genuine Parts for export
They are designed and tested for the tion, counterfeit or used salvage parts are packaged with labels written only
optimum safety, performance, and reli- is not covered under the HYUNDAI in English.
ability to our customers. New Vehicle Limited Warranty or any
HYUNDAI Genuine Parts are only
other HYUNDAI warranty.
sold through authorized HYUNDAI
In addition, any damage to or failure of Dealerships.
HYUNDAI Genuine Parts caused by
the installation or failure of an imitation,
counterfeit or used salvage part is not
covered by any HYUNDAI Warranty.
A100A03L
A100A01L A100A02L A100A04L
F5
Introduction 1
Your vehicle at a glance 2
Features of your vehicle 3
Multimedia System 4
table of contents Driving your vehicle 5

What to do in an emergency 6
Maintenance 7
Consumer information 8
Specifications 9
Index I
Introduction 1
How to use this manual / 1-2
Fuel requirements / 1-2
Vehicle break-in process / 1-4
Introduction
HOW TO USE THIS MANUAL FUEL REQUIREMENTS

We want to help you get the greatest You will find various WARNINGs, Use Diesel
possible driving pleasure from your vehi- CAUTIONs, and NOTICEs in this manual. Diesel fuel
cle. Your Owner’s Manual can assist you These WARNINGs were prepared to
Diesel engine must be operated only on
in many ways. We strongly recommend enhance your personal safety. You should
commercially available diesel fuel that
that you read the entire manual. In order carefully read and follow ALL procedures
complies with EN 590 or comparable
to minimize the chance of death or injury, and recommendations provided in these
standard. (EN stands for "European
you must read the WARNING and CAU- WARNINGs, CAUTIONs and NOTICEs.
Norm"). Do not use marine diesel fuel,
TION sections in the manual.
heating oils, or non-approved fuel addi-
Illustrations complement the words in this WARNING tives, as this will increase wear and
manual to best explain how to enjoy your cause damage to the engine and fuel
A WARNING indicates a situation in
vehicle. By reading your manual, you system. The use of non-approved fuels
which harm, serious bodily injury or
learn about features, important safety and / or fuel additives will result in a limi-
death could result if the warning is
information, and driving tips under vari- tation of your warranty rights.
ignored.
ous road conditions.
Diesel fuel of above cetane 51 is used in
The general layout of the manual is pro- HYUNDAI vehicle. If two types of diesel
vided in the Table of Contents. A good fuel are available, use summer or winter
place to start is the index; it has an alpha- CAUTION fuel properly according to the following
betical listing of all information in your A CAUTION indicates a situation in temperature conditions.
manual. which damage to your vehicle could
Sections: This manual has nine sections result if the caution is ignored.
• Above -5°C (23°F) ... Summer type
plus an index. Each section begins with a
diesel fuel.
brief list of contents so you can tell at a
glance if that section has the information ✽ NOTICE • Below -5°C (23°F) ... Winter type diesel
you want. A NOTICE indicates interesting or help- fuel.
ful information is being provided.
Watch the fuel level in the tank very care-
fully : If the engine stops through fuel fail-
ure, the circuits must be completely
purged to permit.
1 2
Introduction
Biodiesel Repair or replacement of worn or dam-

CAUTION - Diesel fuel Commercially supplied Diesel blends of aged components due to the use of non
(If equipped with DPF) no more than 7% biodiesel, commonly approved fuels will not be covered by the
It is recommended to use the regu- known as "B7 Diesel" may be used in manufactures warranty.
lated automotive diesel fuel for your vehicle if Biodiesel meets EN 14214
diesel vehicle equipped with the or equivalent specifications. (EN stands
CAUTION
DPF system. for "European Norm"). The use of biofu-
els exceeding 7% made from rapeseed • Never use any fuel, whether
If you use diesel fuel including high diesel or B7 biodiesel or other-
sulfur (more than 50 ppm sulfur) and methyl ester (RME), fatty acid methyl
ester (FAME), vegetable oil methyl ester wise, that fails to meet the latest
unspecified additives, it can cause petroleum industry specification.
the DPF system to be damaged and (VME) etc. or mixing diesel exceeding
white smoke can be emitted. 7% with biodiesel will cause increased • Never use any fuel additives or
wear or damage to the engine and fuel treatments that are not recom-
system. Repair or replacement of worn or mended or approved by the vehi-
damaged components due to the use of cle manufacturer.
CAUTION non approved fuels will not be covered by
Do not let any gasoline or water the manufactures warranty.
enter the tank. This would make it Operation in Foreign Countries
necessary to drain it out and to Biodiesel (for New Zealand) If you are going to drive your HYUNDAI
bleed the lines to avoid jamming the Commercially supplied Diesel blends of in another country, be sure to:
injection pump and damaging the no more than 7% biodiesel, commonly • Observe all regulations regarding reg-
engine. known as "B7 Diesel" may be used in istration and insurance.
your vehicle if Biodiesel meets EN 14214 • Determine that acceptable fuel is avail-
or equivalent specifications. (EN stands able.
for "European Norm"). The use of biofu-
els exceeding 7%, made from rapeseed
methyl ester (RME), vegetable oil methyl
ester (VME) etc. or mixing diesel exceed-
ing 7% with biodiesel will cause
increased wear or damage to the engine
and fuel system.
1 3
Introduction
VEHICLE BREAK-IN PROCESS

During the first 1,000 km Before Operation Loading your vehicle
(600 miles) Precautions for New Vehicle Never load the luggage and people to
No formal "break-in" procedure is The performance and life of a vehicle exceed GVWR (MLW) and GAWR of
required with your new HYUNDAI. depend largely on how the vehicle is your vehicle.
However, you can contribute to the eco- handled when new. You can find the GVWR(MLW) and
nomical operation and durability of your To maintain the parts smoothly and sus- GAWR -maximum loading capacities- on
HYUNDAI by observing the following rec- tain high performance for a long time to the VIN plate.
ommendations during the first 1,000 km come, be sure to observe the following The GVWR (Gross Vehicle Weight
(600 miles). points. Rating) or MLW (Maximum Loaded
• While driving, keep your engine speed Make sure that your vehicle does not Weight) means total weight of the vehi-
(rpm, or revolutions per minute) miss the first 5,000 km inspections. cle, all occupants, fuel and cargo. And
between 2,000 rpm and 4,000 rpm. GAWR means the maximum weights that
• While driving, keep under three quar- After the first 5,000 km of driving, take the front and rear axles can endure the
ters of maximum speed. your vehicle to your nearest service shop weights including vehicle itself weight.
• Use moderate acceleration. Don't start, for inspection.
depress the accelerator pedal fully. WARNING
• For the first 300 km (200 miles), try to Improperly loading your car can
avoid hard stops. serious affect its steering and brak-
• Don't lug the engine (in other words, ing performance causing a crash in
don't drive so slowly in too-high a gear which you may be seriously injured
that the engine "bucks": shift to a lower or killed.
gear).
• Whether going fast or slow, vary your
speed from time to time. ✽ NOTICE
• Don't tow a trailer during the first 1,000 Your warranty does not cover parts or
km (600 miles) of operation. components that fail because of over-
• Do not exceed loading limits. loading.
1 4
Your vehicle at a glance 2
Interior overview (I) / 2-2
Interior overview (II) / 2-3
Engine compartment / 2-4
Your vehicle at a glance
INTERIOR OVERVIEW (I)

■ Left-Hand drive type
1. Brake fluid reservoir ...........................7-28

2. Multi-function light switch ...................3-54
3. Instrument cluster ..............................3-41
4. Horn ..................................................3-78
5. Windshield wiper/washer switch.........3-59
6. Audio system* ......................................4-5
7. Heating/air conditioning control panel* .3-79
8. Headlight leveling switch*...................3-61
9. Fuse box ............................................7-40
10. Steering wheel tilt lever* ..................3-78
11. Cigarette lighter................................3-63
12. ESC off button..................................5-12
13. Shift lever ...........................................5-8
14. Ashtray*............................................3-64
15. Glove box .........................................3-67
16. Passenger's front air bag*................3-32
* : if equipped
❈ The actual shape may differ from the illustration.

OHR017003L
2 2
INTERIOR OVERVIEW (II)

■ Right-Hand drive type
1. Heating/Air Conditioning Control

Panel*.................................................3-79
2. Audio System*......................................4-5
3. Hazard Warning Light Switch.............3-61
4. Windshield Wiper/Washer Switch ......3-59
5. Ticket Holder ......................................3-62
6. Horn ...................................................3-78
7. Instrument Cluster..............................3-41
8. Multi-Function Light Switch ................3-54
9. Brake Fluid Reservoir ........................7-28
10. Glove Box.........................................3-67
11. Driver's Drink Holder ........................3-65
12. Shift Lever ..........................................5-8
13. Ashtray*............................................3-64
14. Engine idle RPM Adjustment Knob*..3-64
15. Cigarette Lighter ..............................3-63
16. Steering Wheel Tilt Lever*................3-78
17. Fuse Box ..........................................7-40
18. Hood Release Lever ........................3-72
* : if equipped

OHR016001R
2 3
ENGINE COMPARTMENT
■ Diesel Engine (2.5L Engine)
• Engine room (Passenger's side)
1. Power steering fluid reservoir ...........7-52

2. Engine oil level dipstick ......................7-16
3. Engine oil filler cap.............................7-17
4. Radiator cap.......................................7-21
5. Fuse and relay box.............................7-40
6. Fuel filter ...........................................7-53
• Fuse and Relay Box (Driver's side) • Fuel Filter (Frame under driver's side) CAUTION
To inspect or service the engine,
move the front seat or look at the
frame under the driver's side.

OHR056001/OHR072007/OHR077108
2 4

1. Power steering fluid reservoir ...........7-52

2. Engine oil level dipstick ......................7-16
3. Engine oil filler cap.............................7-17
4. Radiator cap.......................................7-21
5. Fuse and relay box.............................7-40
6. Fuel filter ...........................................7-53

OHR076104L/OHR072007/OHR072010
2 5
Keys / 3-3
Remote keyless entry / 3-5
Door locks / 3-7
Window glass / 3-9
Seats / 3-10
Features of your vehicle 3

Seat belts / 3-16
Child restraint system / 3-22
Air bag - supplemental restraint system / 3-26
Instrument cluster / 3-41
Lighting / 3-54
Wipers and washers / 3-59
Headlight leveling device system / 3-61
Hazard warning system / 3-61
Rear window defroster switch / 3-62
Ticket holder / 3-62
Digital clock / 3-63
Cigarette lighter / 3-63
Ashtray / 3-64
Engine ilde rpm adjustment knob / 3-64
Drink holder / 3-65
Interior light / 3-65
Spectacle case / 3-67
Glove box / 3-67
Center seatback console compartment / 3-69
Outside rearview mirror / 3-70
Day/night inside rearview mirror / 3-71
3 Features of your vehicle

Parking brake / 3-71
Hood release / 3-72
Fuel tank cap / 3-73
Rear gate / 3-74
Side gate / 3-75
Exterior tool box / 3-76
Sun visor / 3-76
Steering wheel / 3-77
Manual climate control system / 3-79
Features of your vehicle
KEYS
Record your key number ■ Type A ■ Type B
The key code number is WARNING - Ignition key

stamped or printed on Leaving children unattended in a
the key code tag vehicle with the ignition key is dan-
attached to the key set. gerous even if the key is not in the
Should you lose your ignition switch is ACC or ON posi-
keys, we recommend that you contact an tion. Children copy adults and they
authorized HYUNDAI dealer. could place the key in the ignition
Remove the key code tag and store it in switch.
a safe place. Also, record the code num- The ignition key would enable chil-
ber and keep it in a safe place (not in the dren to operate power windows or
vehicle). other controls, or even make the
OHD046100/OHR047154 vehicle move, which could result in
Key operations serious bodily injury or even death.
Used to start the engine, lock and unlock Never leave the keys in your vehicle
the doors. with unsupervised children, when
the engine is running.
Type B
To unfold the key, press the release but-
ton then the key will unfold automatically. WARNING
To fold the key, fold the key manually We recommend that you use parts
while pressing the release button. for replacement from an authorized
HYUNDAI dealer.
If an aftermarket key is used, the
CAUTION ignition switch may not return to
Do not fold the key without press- ON after START. If this happens,
ing the release button. This may the starter will continue to operate
damage the key. causing damage to the starter
motor and possible fire due to
excessive current in the wiring.
3 3
Immobilizer system (if equipped) ✽ NOTICE

Your vehicle may be equipped with an WARNING If you need additional keys or lose your
electronic engine immobilizer system to In order to prevent theft of your vehi- keys, we recommend that you consult an
reduce the risk of unauthorized vehicle cle, do not leave spare keys any- authorized HYUNDAI dealer.
use. where in your vehicle. Your
Your immobilizer system is comprised of Immobilizer password is a customer
a small transponder in the ignition key unique password and should be CAUTION
and electronic devices inside the vehicle. kept confidential. Do not leave this The transponder in your ignition
With the immobilizer system, whenever number anywhere in your vehicle. key is an important part of the
you insert your ignition key into the igni- immobilizer system. It is designed
tion switch and turn it to ON, it checks to give years of trouble-free service,
and determines and verifies if the ignition ✽ NOTICE however you should avoid expo-
key is valid or not. When starting the engine, do not use the sure to moisture, static electricity
If the key is determined to be valid, the key with other immobilizer keys around. and rough handling. Immobilizer
engine will start. Otherwise the engine may not start or system malfunction could occur.
may stop soon after it starts. Keep each
If the key is determined to be invalid, the key separate in order to avoid a starting
engine will not start. malfunction. CAUTION
To deactivate the immobilizer sys- Do not change, alter or adjust the
tem: immobilizer system because it
CAUTION could cause the immobilizer sys-
Insert the ignition key into the key cylin- Do not put metal accessories near tem to malfunction.We recommend
der and turn it to the ON position. the ignition switch. that the system be serviced by an
The engine may not start for the authorized HYUNDAI dealer.
To activate the immobilizer system: metal accessories may interrupt the Malfunctions caused by improper
Turn the ignition key to the OFF position. transponder signal from normally alterations, adjustments or modifi-
The immobilizer system activates auto- transmitting. cations to the immobilizer system
matically. Without a valid ignition key for are not covered by your vehicle
your vehicle, the engine will not start. manufacturer warranty.
3 4
REMOTE KEYLESS ENTRY (IF EQUIPPED)

The hazard warning lights will blink twice (Continued)
again to indicate that all doors are • If the transmitter is in close proximity
unlocked. to your cell phone or smart phone, the
After depressing this button, the doors signal from the transmitter could be
will be locked automatically unless you blocked by normal operation of your
open any door within 30 seconds. cell phone or smart phone. This is
especially important when the phone
is active such as making call, receiving
Transmitter precautions calls, text messaging, and/or sending/
✽ NOTICE receiving emails. Avoid placing the
The transmitter will not work if any of transmitter and your cell phone or
following occur: smart phone in the same pants or
OHR047156 • The ignition key is in ignition switch. jacket pocket and maintain adequate
• You exceed the operating distance distance between the two devices.
Remote keyless entry system limit (about 10 m [30 feet]).
operations • The battery in the transmitter is
Lock (1) weak. CAUTION
All doors are locked if the lock/unlock but- • Other vehicles or objects may be Keep the transmitter away from
ton (1) is pressed when a front door is blocking the signal. water or any liquid. If the keyless
unlocked. • The weather is extremely cold. entry system is inoperative due to
If all doors are closed, the hazard warning • The transmitter is close to a radio exposure to water or liquids, it will
lights blink once to indicate that all doors transmitter such as a radio station or not be covered by your manufactur-
are locked. an airport which can interfere with er vehicle warranty.
However, if any door remains open, the normal operation of the transmitter.
hazard warning lights will not operate. If all When the transmitter does not work
doors are closed after the lock button is correctly, open and close the door with
pressed, the hazard warning lights blink. the ignition key. If you have a problem
with the transmitter, we recommend
that you contact an authorized
Unlock (2) HYUNDAI dealer.
All doors are unlocked if the lock/unlock (Continued)
button (2) is pressed when both front
doors are locked.
3 5
CAUTION CAUTION
Changes or modifications not • The keyless entry system trans-
expressly approved by the party mitter is designed to give you
responsible for compliance could years of trouble-free use, howev-
void the user’s authority to operate er it can malfunction if exposed to
the equipment. If the keyless entry moisture or static electricity.
system is inoperative due to If you are unsure how to use your
changes or modifications not transmitter or replace the battery,
expressly approved by the party we recommend that you contact
responsible for compliance, it will an authorized HYUNDAI dealer.
not be covered by your manufactur- • Using the wrong battery can
er’s vehicle warranty. OLM042302 cause the transmitter to malfunc-
Battery replacement tion. Be sure to use the correct
battery.
If the remote key is not working properly,
CAUTION try replacing the battery with a new one. • To avoid damaging the transmit-
Keep the transmitter away from ter, don't drop it, get it wet, or
To replace the battery:
electromagnetic materials that expose it to heat or sunlight.
blocks electromagnetic waves to 1. Insert a slim tool into the slot and gen-
• An inappropriately disposed bat-
the key surface. tly pry open the cover.
tery can be harmful to the envi-
2. Remove the old battery and insert the ronment and human health.
new battery. Make sure the battery
Dispose the battery according to
position is correct.
your local law(s) or regulation.
3. Reinstall the rear cover of the remote
key.
If you suspect your remote key might
have sustained some damage, or you
feel your remote key is not working cor-
rectly, it is recommended that you con-
tact an authorized HYUNDAI dealer.
3 6
DOOR LOCKS
Locking and Unlocking Front
WARNING Doors with a Key
• Unlocked doors can be danger- • The door can be locked or unlocked
ous. Before you drive away (espe- with a key.
cially if there are children in the • Lock the door by turning the key
car), be sure that all the doors are toward the rear of the vehicle and
securely closed and locked so unlock it by turning the key toward the UNLOCK
that the doors cannot be inadver- front.
tently opened from the inside.
This helps ensure that the doors LOCK
will not be opened accidentally.
Also, when combined with the
proper use of seat belts, locking B040C01HR
the doors helps keep occupants Locking From the Outside
from being ejected from the car in
The doors can be locked without a key.
case of an accident.
To lock the doors, first push the inside
• Before opening the door, always
lock switch to the "LOCK" position so that
look for and avoid oncoming traf-
the red mark on the switch is not visible,
fic.
then close the door.
• If you don’t close the door
securely, the door may open
again. ✽ NOTICE
• Be careful that someone’s body • When locking the door this way, be
and hands are not trapped when careful not to lock the door with the
closing the door. ignition key left in the vehicle.
• To protect against theft, always
remove the ignition key, close all win-
dows, and lock all doors when leaving
your vehicle unattended.
3 7
✽ NOTICE
• When pushing the switch toward the
rear, all doors will unlock.
When pushing the switch toward the
front, all doors will lock.
• When the door is unlocked, the red
mark on the switch is visible and the
UNLOCK
character "LOCK" on the switch is
not visible.
LOCK LOCK
• The central door locking is operated
UNLOCK by turning the key (driver's door only)
toward the front or rear of the vehicle.
HHR2023A B040C01HR
Locking From the Inside Central Door Lock (if equipped) CAUTION
To lock the doors from the inside, simply The central door locking is operated by If the door is locked/unlocked multi-
close the door and push the lock switch pushing the driver's door lock switch ple times in rapid succession with
to the "LOCK" position. When this is toward the front or rear of the vehicle. If either the vehicle key or door lock
done, neither the outside nor the inside the passenger or rear doors are open switch, the system may stop oper-
door handle can be used. when the switch is pushed, the door will ating temporarily in order to protect
remain locked when closed. the circuit and prevent damage to
✽ NOTICE system components.
When the door is locked, the red mark
on the switch is not visible and the char-
acter "LOCK" on the switch is visible.
3 8
WINDOW GLASS
Auto-Down Window
(Driver's Side) (if equipped)
OPEN
The Auto-Down window is moved to its
fully open position by pushing the switch.
CLOSE
To stop at the desired position push the
OPEN
switch again.
CLOSE
WARNING
1)Be careful that someone's head,
hands and body are not trapped
by a closing window.
B050A01HR OHR047191L 2)Never try to operate the main
To raise or lower the window, turn the Power windows (if equipped) switch on the driver's door and
window regulator handle clockwise or The power windows operate when the the passenger's door window
counterclockwise. ignition key is in the "ON" position. The switch in opposing directions at
main switches are located on the driver's the same time. If this is done, the
armrest and control the front windows on window will stop and cannot be
WARNING opened or closed.
both sides of the vehicle. The windows
When opening or closing the win- 3)Do not leave children alone in the
may be opened by depressing the appro-
dows, make sure your passenger's car. Always remove the ignition
priate window switch and closed by
arms, hands and body are safely key for their safety.
pulling up the switch. To open the window
out of the way.
on the driver's side, press the switch(1)
down. The window moves as long as the
switch is operated.
WARNING
To avoid serious injury or death, do
not extend your head, arms or body
outside the windows while driving.
3 9
SEATS
WARNING
Never attempt to adjust the seat
while the vehicle is moving. This
could result in loss of control or an
accident which may cause death,
serious injury, or property damage.
WARNING
• Do not adjust the seat while wear-
ing seat belts. Moving the seat HHR2043 HHR2044
cushion forward may cause strong
pressure on the abdomen. Front seats Adjusting Seatback Angle
Adjusting Seat Forward and (Driver's Seat Only) (if equipped)
• Use extreme caution so that hands
or other objects are not caught in Rearward (Driver's Seat Only) To recline the seatback, lean forward to
the seat mechanisms while the To move the seat toward the front or rear, take your weight off it, then pull up on the
seat is moving. pull the lock release lever upward. This recliner control lever at the outside edge
will release the seat on its track so you of the seat. Now lean back until the
• Do not put a cigarette lighter on desired seatback angle is achieved. To
the floor or seat.When you operate can move it forward or rearward to the
desired position. lock the seatback into position, release
the seat, gas may gush out of the the recliner control lever.
lighter and cause fire. When you find the position you want,
• If there are occupants in the rear release the lever and slide the seat for-
seats, be careful while adjusting ward or rearward on its track until it locks
into the desired position and cannot be
the front seat position.
moved further.
• Use extreme caution when picking
small objects trapped under the
seats or between the seat and the WARNING
center console. Your hands might To ensure the seat is locked
be cut or injured by the sharp securely, attempt to move the seat
edges of the seats mechanism. forward or rearward without using
the lock release lever.
3 10
WARNING
To minimize risk of severe injury in
the event of a collision or a sudden
stop, both the driver and passenger
seatbacks should always be in an
upright position while the vehicle is
in motion. The protection provided
by the seat belts in a frontal colli-
sion may be reduced significantly
when the seatbacks are reclined.
There is greater risk that the driver
and passenger will slide under the B080D01HR OHR033100
seat belt which may result in seri- Adjustable Headrests Removal
ous injury if a crash occurs when Headrests are designed to help reduce To remove the headrest:
the seatbacks are reclined. The seat the risk of neck injuries. 1. Recline the seatback (2) with the
belt cannot provide full protection
To raise the headrest, pull it up. To lower recline lever (1).
to an occupant if the seatback is
reclined. it, push it down while pressing the lock 2. Raise headrest as far as it can go.
knob. To remove the headrest, raise it as 3. Press the headrest release button (3)
far as it can go then press the lock knob while pulling the headrest up (4).
while pulling upward.
WARNING
NEVER allow anyone to ride in a
seat with the headrest removed.
3 11
WARNING
B080D01JM HHR2045
Reinstall Lumbar Support Control
To reinstall the headrest : • For maximum effectiveness in (Driver's seat only) (if equipped)
case of an accident the headrest To adjust the lumbar support, turn the
1. Put the headrest poles (2) into the
should be adjusted so the middle handle on the inboard side of the seat. To
holes while pressing the release button
of the headrest is at the same increase the amount of lumbar support,
(1).
height as the top of the occupant's pull the lever forward. To decrease it,
2. Recline the seatback (4) with the eyes. For this reason, the use of a
recline lever (3). push the lever toward the rear.
cushion that holds the body away
3. Adjust the headrest to the appropriate from the seatback should not be
height. recommended. 1. Minimum support
• Do not operate vehicle with the 2. Maximum support
headrests removed as injury to the
WARNING occupants may occur in the event
Always make sure the headrest of an accident. Headrests may pro-
locks into position after reinstalling vide protection against neck
and adjusting it properly. injuries when properly adjusted.
• Do not adjust the headrest height
while the vehicle is in motion.
3 12
Lever
HHR2048 OHR034105 OHR074110

Center Seat (With Seatback Console Rear seat (if equipped) To use the rear seat cushion under box,
Compartment) (if equipped) Rear Seat Cushion Under Box pull up the clamp levers on the both sides
• To use the console compartment, push of the cushion and unhook the clamp
There is mutipurpose receipt space
down the lever and tilt the seatback for- from the seat cushion's hook. And then,
under the rear seat cushion.
ward. pull the strap on the seat cushion.
• To use the center seat, lift up the seat-
back until it locks into position.
WARNING
When you return the seat cushion
CAUTION to its original position, make sure
When lifting up the seatback, do not the seat belts are in position to be
place any object on the console accessible and to function properly.
compartment.
3 13
To access the engine

The engine compartment can be
checked by moving the driver's seat and
the front passenger's seat.
B300B02HR HHR2047A
2. Pull the recliner control lever and tilt To Inspect the Engine Compartment
the seatback forward. Under the Front Passenger's Seat
(Fixed Seatback type)
1. Pull the clamp lever up and unhook the
B300B01HR
clamp from the seat pan's hook.
To Inspect the Engine Compartment

Under the Diver's Seat
1. Move the seat all the way forward by
pulling the lever up.
OHR072009
3. After lifting up the mat, open the
access hole cover by removing the nut
with a spanner.
3 14
St r a p St r a p
OHR2048 HHR2047 OHR2132

2. Lift up the seat cushion and secure the To Inspect the Engine Compartment 3. Lift up the seat cushion and secure the
strap to the seat pan's hook on the left Under the Front Passenger's Seat strap to the seat pan's hook on the left
side to hold the seat. (Folding Seatback type) side to hold the seat.
And then, inspect the engine compart- 1. Pull the recliner control lever (1) and tilt And then, inspect the engine compart-
ment under the front passenger seat. the seatback forward. ment under the front passenger seat.
2. Pull the clamp lever (2) up and unhook
✽ NOTICE the clamp from the seat pan's hook. ✽ NOTICE
To return the seat cushion to its normal To return the seat cushion to its normal
position, reverse the above procedure. position, reverse the above procedure.
3 15
SEAT BELTS
Seat belt restraint system (Continued) (Continued)
• Avoid wearing twisted seat belts. Care should be taken to avoid con-
WARNING A twisted belt can't do its job as tamination of the webbing with pol-
• For maximum restraint system pro- well. In a collision, it could even ishes, oils and chemicals and par-
tection, the seat belts must always cut into you. Be sure the belt web- ticularly battery acid. Cleaning may
be used whenever the car is mov- bing is straight and not twisted. safely be carried out using mild
ing. • Be careful not to damage the belt soap and water. The belt should be
• Seat belts are most effective when webbing or hardware. If the belt replaced if webbing becomes
seatbacks are in the upright posi- webbing or hardware is dam- frayed, contaminated or damaged.
tion. aged, replace it. It is essential to replace the entire
• Children age 12 and under must assembly after it has been worn in
always be properly restrained in a severe impact even if damage to
the rear seat. Never allow children the assembly is not obvious. Belts
to ride in the front passenger seat. WARNING should not be worn with straps
If a child over 12 must be seated in Seat belts are designed to bear twisted. Each seat belt assembly
the front seat, he/she must be prop- upon the bony structure of the must only be used by one occu-
erly belted and the seat should be body, and should be worn low pant; it is dangerous to put a belt
moved as far back as possible. across the front of the pelvis, or the around a child being carried on the
• Never wear the shoulder belt under pelvis, chest and shoulders, as occupant's lap.
your arm or behind your back. An applicable; wearing the lap section
improperly positioned shoulder of the belt across the abdominal
belt can cause serious injuries in a area must be avoided.
crash. The shoulder belt should be Seat belts should be adjusted as
positioned midway over your firmly as possible, consistent with
shoulder across your collarbone. comfort, to provide the protection
• Never wear a seat belt over frag- for which they have been designed.
ile objects. If there is a sudden A slack belt will greatly reduce the
stop or impact, the seat belt can protection afforded to the occupant.
damage it. (Continued)
(Continued)
3 16
If you continue not to fasten the seat belt

WARNING and you drive over 20 km/h (12 mph) the
• No modifications or additions seat belt warning chime will sound for
should be made by the user approximately 100 seconds and the cor-
which will either prevent the seat responding warning light will blink.
belt adjusting devices from oper-
ating to remove slack, or prevent
the seat belt assembly from being
adjusted to remove slack.
• When you fasten the seat belt, be
careful not to latch the seat belt in
buckles of other seat. It's very dan-
gerous and you may not be pro- 1GQA2083
tected by the seat belt properly. Seat belt warning (if equipped)
• Do not unfasten the seat belt and As a reminder to the driver or front pas-
do not fasten and unfasten the senger (if equipped), the seat belt warn-
seat belt repeatedly while driving. ing lights will illuminate for approximately
This could result in loss of con- 6 seconds when the ignition key is turned
trol, and an accident causing from the "OFF" position to "ON" regard-
death, serious injury, or property less of belt fastening.
damage. If the driver's seat belt or the front pas-
• When fastening the seat belt, senger's seat belt (if equipped) is not fas-
make sure that the seat belt does tened when the ignition key is turned to
not pass over objects that are the "ON" position or if it is disconnected
hard or can break easily. after the ignition key is turned to the "ON"
• Make sure there is nothing in the position, the seat belt warning light will
buckle. The seat belt may not be illuminate until the belt is fastened.
fastened securely.
3 17
Seat belt precautions Larger Children Injured Person

All occupants of the vehicle should wear Children who are too large for child A seat belt should be used when an
their seat belts at all times. Indeed, your restraint systems should always occupy injured person is being transported.
province's laws may require that some or the rear seat and use the available When this is necessary, you should con-
all occupants of the vehicle use seat lap/shoulder belts. The lap portion should sult a physician for recommendations.
belts. be fastened snug on the hips and as low
The possibility of injury or the severity of as possible. Check belt fit periodically. A One Person Per Belt
injury in an accident will be decreased if child's squirming could put the belt out of
position. Children are afforded the most Two people (including children) should
this elementary safety precaution is
safety in the event of an accident when never attempt to use a single seat belt.
observed. In addition, follow the other
they are restrained by a proper restraint This could increase the severity of
instructions provided in this section.
system in the rear seat. If a larger child injuries in case of an accident.
(over age 13) must be seated in the front
Infant or Small Child seat, the child should be securely Do Not Lie Down
Some countries require the use of child restrained by the available lap/shoulder To reduce the chance of injuries in the
restraint systems for infants and small belt and the seat should be placed in the event of an accident and to achieve max-
children. Whether this is required by law rearmost position. Children under the imum effectiveness of the restraint sys-
or not, it is strongly recommended that a age of 13 should be restrained securely tem, all passengers should be sitting up
child restraint seat or infant restraint sys- in the rear seat. NEVER place a child and the front seats should be in an
tem be used for infants or small children under the age of 13 in the front seat. upright position when the car is moving.
weighing less than 18 kilograms (40 NEVER place a rear facing child seat in A seat belt cannot provide proper protec-
pounds). the front seat of a vehicle. tion if the person is lying down in the rear
seat or if the front seat is in a reclined
✽ NOTICE Pregnant Women position.
Small children are best protected in an The use of a seat belt is recommended
accident when properly restrained by a for pregnant women to lessen the chance
child restraint system. of injury in an accident. When a seat belt
is used, it should be placed as low and
snugly as possible on the hips, not
across the abdomen. For specific recom-
mendations, consult a physician.
3 18
Periodic Inspection
WARNING It is recommended that all seat belts be
Sitting in a reclined position or inspected periodically for wear or dam-
lying down when your vehicle is in age of any kind. Parts of the system that
motion can be dangerous. Even if are damaged should be replaced as
you buckle up, your seat belts can't soon as possible.
do their job when you're reclined.
The shoulder belt can't do its job Keep Belts Clean and Dry
because it won't be against your Seat belts should be kept clean and dry.
body. Instead, it will be in front of If belts become dirty, they can be
you. In a crash you could go into it cleaned by using a mild soap solution
with great force, receiving serious and warm water. Bleach, dye, strong
neck or other injuries. B180A01L
detergents or abrasives should not be
The lap belt can't do its job either. used because they may damage and SEAT BELTS 3-Point System with
In a crash the belt could go up over weaken the fabric. Emergency Locking Retractor
your abdomen. The belt forces To Fasten Your Belt
would be applied there, not at your When to Replace Seat Belts
strong pelvic bones. This could To fasten your seat belt, pull it out of the
Entire in-use seat belt assembly or retractor and insert the metal tab into the
cause serious internal injuries.
assemblies should be replaced if the buckle. There will be an audible "click"
For proper protection when the vehi- vehicle has been involved in an accident. when the tab locks into the buckle.
cle is in motion, have the seatback This should be done even if no damage
upright.Then sit back in the seat and is visible. Additional questions concern-
wear your seat belt properly. ing seat belt operation should be directed
to your HYUNDAI Dealer.
Care of Seat Belts
Seat belt systems should never be disas-
sembled or modified. In addition, care
should be taken to assure that seat belts
and belt hardware are not damaged by
seat hinges, doors or other abuse.
3 19
✽ NOTICE
If you are not able to pull out the seat
belt from the retractor, firmly pull the
belt out and release it. Then you will be
able to pull the belt out smoothly.
WARNING
• When you fasten the seat belt, be
careful not to latch the seat belt
in buckles of other seat. It's very
dangerous and you may not be
OHR037001L protected by the seat belt proper- B200A01L
You should place the lap belt (1) portion ly. Adjusting Your Seat Belt
across your hips and the shoulder belt (2) • Do not unfasten the seat belt and You should place the belt as low as pos-
portion across your chest. do not fasten and unfasten the sible on your hips, not on your waist. If
The seat belt automatically adjusts to the seat belt repeatedly while driving. the belt is located too high on your body,
proper length only after the lap belt is This could result in loss of con- you could slide under it in case of acci-
adjusted manually so that it fits snugly trol, and an accident causing dent or a sudden stop. This could result
around your hips. If you lean forward in a death, serious injury, or property of death, serious injury or property dam-
slow, easy motion, the belt will extend and damage. age. Both arms should not be under or
let you move around. • When fastening the seat belt, over the belt. Rather, one should be over
If there is a sudden stop or impact, howev- make sure that the seat belt does and the other under, as shown in the
er, the belt will lock into position. It will also not pass over objects that are illustration.
lock if you try to lean forward too quickly. hard or can break easily. Never wear the seat belt under the arm
Check to make sure that the belt is prop- • Make sure there is nothing in the nearest the door.
erly locked and that the belt is not twisted. buckle. The seat belt may not be
fastened securely.
• Never wear a seat belt over frag-
ile objects. If there is a sudden
stop or impact, the seat belt can
damage it.
3 20
Too
high
Shorten
Correct
B210A01L HTB225 HTB226

To Release the Seat Belt Seat Belts (2-Point Static Type) Adjusting Your Seat Belt
The seat belt is released by pressing the To Fasten Your Seat Belt With a 2-point static type seat belt, the
release button in the locking buckle. To fasten a 2-point static type belt, insert length must be adjusted manually so it
When it is released, the belt should auto- the metal tab into the locking buckle. fits snugly around your body. Fasten the
matically draw back into the retractor. There will be an audible "click" when the belt and pull on the loose end to tighten.
If this does not happen, check the belt to tab locks into the buckle. Check to make The belt should be placed as low as pos-
be sure it is not twisted, then try again. sure the belt is properly locked and that sible on your hips, not on your waist. If
the belt is not twisted. the belt is too high, it could increase the
possibility of your being injured in an
accident.
3 21
CHILD RESTRAINT SYSTEM (IF EQUIPPED)

Children riding in the car should sit in the
rear seat and must always be properly WARNING
restrained to minimize the risk of injury in • A child restraint system must be
an accident, sudden stop or sudden placed in the rear seat. Never
maneuver. According to accident statis- install a child or infant seat on the
tics, children are safer when properly front passenger's seat.
restrained in the rear seats than in the Should an accident occur it
front seat. Larger children not in a child could severely injure or kill an
restraint should use one of the seat belts infant or child seated in an infant
provided. or child seat. Thus, only use a
You are required by law to use safety child restraint in the rear seat of
restraints for children. If small children your vehicle.
B220C01HR ride in your vehicle you must put them in • Since a safety belt or child
To Release the Seat Belt a child restraint system (safety seat). restraint system can become
Child restraint systems are designed to very hot if it is left in a closed
When you want to release the seat belt,
be secured in vehicle seats by lap belts vehicle, be sure to check the seat
press the button in the locking buckle.
or the lap belt portion of a lap/shoulder cover and buckles before placing
belt, or by a tether anchor and/or ISOFIX a child there.
WARNING anchors (if equipped).
• When the child restraint system
The center lap belt latching mecha- Children could be injured or killed in a is not in use, fasten it with a safe-
nism is different from those for the crash if their restraints are not properly ty belt so that it will not be thrown
front seat shoulder belts. When fas- secured. For small children and babies, a forward in the case of a sudden
tening the front seat shoulder belts child seat or infant seat must be used. stop or an accident.
or the center lap belt, make sure Before buying a particular child restraint
system, make sure it fits your car and • Children who are too large to be
they are inserted into the correct in a child restraint should sit in
buckles to obtain maximum protec- seat belts, and fits your child. Follow all
the instructions provided by the manufac- the rear seat and be restrained
tion from the seat belt system and with the available lap/shoulder
assure proper operation. turer when installing the child restraint
system. belts. Never allow children to ride
in the front passenger seat.
(Continued)
3 22
(Continued) (Continued) (Continued)

• Always make sure that the shoul- • Never use an infant carrier or • If there is not enough space to
der belt portion of the outboard child safety seat that "hooks" place the child restraint system
lap/shoulder belt is positioned over a seatback; it may not pro- because of the driver's seat,
midway over the shoulder, never vide adequate security in an acci- install the child restraint system
across the neck or behind the dent. in the rear right seat.
back. Moving the child closer to Never allow a child to be held in a • If the vehicle headrest prevents
the center of the vehicle may help person's arms while they are in a proper installation of a child seat
provide a good shoulder belt fit. moving vehicle, as this could (as described in the child seat
The lap belt portion of the result in serious injury to the system manual). the headrest of
lap/shoulder belt or the center child in the event of an accident the respective seating position
seat lap belt must always be posi- or a sudden stop. Holding a child shall be readjusted or entirely
tioned as low as possible on the in a moving vehicle does not pro- removed.
child's hips and as snug as pos- vide the child with any means of
sible. protection during an accident,
• If the seat belt will not properly fit even if the person holding the
the child, HYUNDAI recommends child is wearing a seat belt.
the use of an approved booster • If the child restaint seat is not
seat in the rear seat in order to anchored properly, the risk of a
raise the child's seating height so child being seriously injured or
that the seat belt will properly fit killed in a collision greatly
the child. increases.
• Never allow a child to stand up or • After an accident, we recommend
kneel on the seat. that the system be checked by an
(Continued) authorized HYUNDAI dealer.
(Continued)
3 23
If you need to tighten the belt, pull more

webbing toward the retractor. When you
unbuckle the seat belt and allow it to
retract, the retractor will automatically
revert back to its normal seated passen-
ger emergency locking usage condition.
✽ NOTICE
• Before installing the child restraint
system, read the instructions supplied
by the child restraint system manufac-
turer.
B230F01HR B230G01HR • If the seat belt does not operate as
Installation on Front Seat Center Installation on Outboard Front described in this section, we recom-
Position Passenger's Seat mend that the system be checked by
Use the center seat belt to secure the To install a child restraint system on the an authorized HYUNDAI dealer.
child restraint system as illustrated. After outboard front passenger's seat, extend
installation of the child restraint system, the shoulder/lap belt from its retractor.
rock the child seat back and forth, and Install the child restraint system, buckle
side to side to ensure that it is properly the seat belt and allow the seat belt to
secured by the seat belt. take up any slack. Make sure that the lap
If the child seat moves, readjust the portion of the belt is tight around the child
length of the seat belt. Then, if equipped, restraint system and the shoulder portion
insert the child restraint tether strap hook of the belt is positioned so that it cannot
into the child restraint hook holder and interfere with the child's head or neck.
tighten to secure the seat. Always refer to After installation of the child restraint sys-
the child restraint system manufacturer's tem, try to move it in all directions to be
recommendation before installing the sure the child restraint system is securely
child restraint system in your vehicle. installed.
3 24
Child Seat Restraint Suitability For Seat Position
Seating Position
Age Group
Passenger Outboard Passenger Center
0 : Up to 10 kg
X X
(0 ~ 9 months)
0+ : Up to 13 kg
U X
(0 ~ 2 years)
I : 9kg to 18kg
UF UF
(9 months ~ 4 years)
II & III : 15kg to 36kg
X X
(4 ~ 12 years)
Use child safety seats that have been officially approved and are appropriate for your children. When using the child safety seats,
refer to the following table.
U : Suitable for "universal" category restraints approved for use in this mass group (PEG-PEREGO E13 03 0010 083779)
UF : Suitable for forward-facing "universal" category restraints approved for use in this mass group
(ROMER E1 03301133)
X : Seat position not suitable for children in this mass group
3 25
AIR BAG - SUPPLEMENTAL RESTRAINT SYSTEM (IF EQUIPPED)

(1) Driver’s front air bag
(2) Passenger’s front air bag*
* : if equipped
WARNING
• Even in vehicles with air bags,
you and your passengers must
always wear the safety belts pro-
vided in order to minimize the
risk and severity of injury in the
event of a collision or rollover.
• SRS and pretensioners contain
explosive chemicals. If scraping
a vehicle without removing SRS
and pretensioners from a vehicle,
it may cause fire. Before scraping
a vehicle, we recommend that
you contact an authorized
HYUNDAI dealer.
• Keep the SRS parts and wirings
away from water or any liquid. If
the SRS components are inoper-
ative due to exposure to water or
liquids, it may cause fire or
❈ The actual air bags in the vehicle may differ from the illustration. severe injury.
OJK034068
3 26
How does the air bag system • In order to help provide protection in a
operate severe collision, the air bags must WARNING
• Air bags are activated (able to inflate if inflate rapidly. The speed of air bag • To avoid severe personal injury
necessary) only when the ignition inflation is a consequence of the or death caused by deploying air
switch is turned to the ON or START extremely short time in which a collision bags in a collision, the driver
position. occurs and the need to inflate the air should sit as far back from the
• Air bags inflate instantly in the event of bag between the occupant and the steering wheel air bag as possi-
a serious frontal collision in order to vehicle structures before the occupant ble (at least 250 mm (10 inches)
help protect the occupants from seri- impacts those structures. This speed of away). The front passengers
ous physical injury. inflation reduces the risk of serious or should always move their seats
• There is no single speed at which the life-threatening injuries in a severe col- as far back as possible and sit
air bags will inflate. lision and is thus a necessary part of air back in their seat.
bag design. • Air bags inflate instantly in the
Generally, air bags are designed to
inflate based upon the severity of a col- However, air bag inflation can also event of collision, and passen-
lision and its direction. These two fac- cause injuries which can include facial gers may be injured by the air bag
tors determine whether the sensors abrasions, bruises and broken bones expansion force if they are not in
produce an electronic deployment/ because the inflation speed also caus- proper position.
inflation signal. es the air bags to expand with a great • Air bag inflation may cause
• Air bag deployment depends on a deal of force. injuries including facial or bodily
number of factors including vehicle • There are even circumstances abrasions, injuries from broken
speed, angles of impact and the densi- under which contact with the steer- glasses or burns.
ty and stiffness of the vehicles or ing wheel air bag can cause fatal
objects which your vehicle hits in the injuries, especially if the occupant
collision. The determining factors are is positioned excessively close to
not limited to those mentioned above. the steering wheel.
• The front air bags will completely
inflate and deflate in an instant.
It is virtually impossible for you to see
the air bags inflate during an accident.
It is much more likely that you will sim-
ply see the deflated air bags hanging
out of their storage compartments after
the collision.
3 27
Noise and smoke ■ Type A Do not install a child restraint on

When the air bags inflate, they make a the front passenger’s seat
loud noise and they leave smoke and Never place a rear-facing child restraint
powder in the air inside of the vehicle. in the front passenger’s seat. If the air
This is normal and is a result of the igni- bag deploys, it would impact the rear-fac-
tion of the air bag inflator. After the air ing child restraint, causing serious or
bag inflates, you may feel substantial dis- fatal injury.
comfort in breathing due to the contact of In addition, do not place front-facing child
your chest with both the seat belt and the restraints in the front passenger’s seat
air bag, as well as from breathing the 1JBH3051
either. If the front passenger air bag
smoke and powder. Open your doors ■ Type B
inflates, it could cause serious or fatal
and/or windows as soon as possible injuries to the child.
after impact in order to reduce dis-
comfort and prevent prolonged expo-
sure to the smoke and powder. WARNING
Though the smoke and powder are non- • Extreme Hazard! Do not use a
toxic, they may cause irritation to the skin rearward facing child restraint on
(eyes, nose and throat, etc). If this is the a seat protected by an air bag in
case, wash and rinse with cold water front of it!
immediately and consult a doctor if the OYDESA2042 • Never put a child restraint in the
symptom persists. ■ Type C front passenger’s seat. If the front
passenger air bag inflates, it can
cause serious or fatal injuries.
WARNING
When the air bags deploy, the air
bag related parts in the steering
wheel and/or instrument panel are
very hot. To prevent injury, do not
touch the air bag storage area’s
internal components immediately OLM034310
after an air bag has inflated.
3 28
SRS components and functions Driver’s front air bag (1)

The SRS consists of the following com-
ponents:
1. Driver's front air bag module
2. Passenger's front air bag module
3. Air bag warning light
4. SRS control module (SRSCM)
5. Front impact sensors
* : if equipped
W7-147 The SRSCM continually monitors all B240B01L

Air bag warning light SRS components while the ignition The front air bag modules are located
switch is ON to determine if a crash both in the center of the steering wheel
The purpose of the air bag warning light impact is severe enough to require air
in your instrument panel is to alert you of and in the front passenger's panel above
bag deployment or pre-tensioner seat the glove box. When the SRSCM detects
a potential problem with your air bag - belt deployment.
Supplemental Restraint System (SRS). a sufficiently severe impact to the front of
The SRS air bag warning light on the the vehicle, it will automatically deploy
When the ignition switch is turned ON, instrument panel will illuminate for about 6 the front air bags.
the warning light should illuminate for seconds after the ignition switch is turned
approximately 6 seconds, then go off. to the ON position, after which the SRS air
Have the system checked if: bag warning light should go out.
• The light does not turn on briefly when If any of the following conditions occurs,
you turn the ignition ON. this indicates a malfunction of the SRS. We
• The light stays on after illuminating for recommend that the system be inspected
approximately 6 seconds. by an authorized HYUNDAI dealer.
• The light comes on while the vehicle is • The light does not turn on briefly when
in motion. you turn the ignition ON.
• The light stays on after illuminating for
approximately 6 seconds.
• The light comes on while the vehicle is
in motion.
3 29
Driver’s front air bag (2) Driver’s front air bag (3) Passenger’s front air bag
B240B02L B240B03L B240B05L

Upon deployment, tear seams molded A fully inflated air bag, in combination
directly into the pad covers will separate with a properly worn seat belt, slows the WARNING
under pressure from the expansion of the driver's or the passenger's forward • Do not install or place any acces-
air bags. Further opening of the covers motion, reducing the risk of head and sories (drink holder, cassette
then allows full inflation of the air bags. chest injury. holder, sticker, etc.) on the front
passenger's panel above the
After complete inflation, the air bag glove box in a vehicle with a pas-
immediately starts deflating, enabling the senger's air bag. Such objects
driver to maintain forward visibility and may become dangerous projec-
the ability to steer or operate other con- tiles and cause injury if the pas-
trols. senger's air bag inflates.
• When installing a container of liq-
uid air freshener inside the vehi-
cle, do not place it near the
instrument cluster nor on the
instrument panel surface.
It may become a dangerous pro-
jectile and cause injury if the pas-
senger's air bag inflates.
3 30
Driver’s front air bag

(Continued)
WARNING
If this occurs, we recommend
• If an air bag deploys, there may that the system be inspected by
be a loud noise followed by a fine an authorized HYUNDAI dealer.
dust released in the vehicle.
These conditions are normal and • Before you replace a fuse or dis-
are not hazardous - the air bags connect a battery terminal, turn
are packed in this fine powder. the ignition switch to the LOCK
The dust generated during air position and remove the ignition
bag deployment may cause skin key. Never remove or replace the
or eye irritation as well as aggra- air bag related fuse(s) when the
vate asthma for some persons. ignition switch is in the ON posi-
Always wash all exposed skin tion. Failure to heed this warning OHR022205
areas thoroughly with cold water will cause the SRS air bag warn-
ing light to illuminate. Driver's and passenger's front air
and a mild soap after an accident bag (if equipped)
in which the air bags were
Your vehicle is equipped with a
deployed.
Supplemental Restraint (Air Bag) System
• The SRS can function only when and lap/shoulder belts at both the driver
the ignition switch is in the ON and passenger seating positions. The
position. If the SRS air bag warn- indications of the system's presence are
ing light does not illuminate, or the letters "SRS AIR BAG" embossed on
continuously remains on after the air bag pad cover in the steering
illuminating for about 6 seconds wheel and the passenger's side front
when the ignition switch is turned panel pad above the glove box.
to the ON position, or after the
engine is started, comes on while
driving, the SRS is not working The SRS consists of air bags installed
properly. under the pad covers in the center of the
steering wheel and the passenger's side
(Continued)
front panel above the glove box.
3 31
Passenger’s front air bag

(Continued) (Continued)
Always follow the precautions about • No objects (such as crash pad
seat belts, air bags and occupant cover, cellular phone holder, cup
safety contained in this manual. holder, perfume or stickers)
To reduce the chance of serious or should be placed over or near the
fatal injuries and receive the maxi- air bag modules on the steering
mum safety benefit from your wheel, instrument panel, wind-
restraint system: shield glass, and the front pas-
• Never place a child in any child or senger's panel above the glove
booster seat in the front seat. box. Such objects could cause
• ABC – Always Buckle Children in harm if the vehicle is in a crash
the back seat. It is the safest place severe enough to cause the air
OHR037108
for children of any age to ride. bags to deploy.
The purpose of the SRS is to provide the • Do not attach any objects on the
vehicle's driver and/or the front passen- • Front air bags can injure occu-
pants improperly positioned in front windshield and inside mirror.
ger with additional protection than that • Do not tamper with or disconnect
offered by the seat belt system alone in the front seats.
• Move your seat as far back as SRS wiring or other components
case of a frontal impact of sufficient of the SRS system. Doing so
severity. practical from the front air bags,
while still maintaining control of could result in injury, due to acci-
the vehicle. dental deployment of the air bags
WARNING • You and your passengers should
or by rendering the SRS inopera-
Always use seat belts and child tive.
never sit or lean unnecessarily
restraints – every trip, every time, close to the air bags. Improperly • If the SRS air bag warning light
everyone! Air bags inflate with con- positioned drivers and passen- remains illuminated while the
siderable force and in the blink of an gers can be severely injured by vehicle is being driven, we rec-
eye. Seat belts help keep occupants inflating air bags. ommend that the system be
in proper position to obtain maxi- inspected by an authorized
• Never lean against the door or
mum benefit from the air bag. Even HYUNDAI dealer.
center console – always sit in an
with air bags, improperly and unbelt- (Continued)
upright position.
ed occupants can be severely
injured when the air bag inflates. (Continued)
(Continued)
3 32
(Continued) (Continued) (Continued)

• Air bags can only be used once – • Children age 12 and under must • Sitting improperly or out of posi-
we recommend that the system always be properly restrained in tion can result in serious or fatal
be replaced by an authorized the rear seat. Never allow children injury in a crash. All occupants
HYUNDAI dealer. to ride in the front passenger seat. should sit upright with the seat
• The SRS is designed to deploy the If a child over 12 must be seated in back in an upright position, cen-
front air bags only when an impact the front seat, he or she must be tered on the seat cushion with
is sufficiently severe and when properly belted and the seat their seat belt on, legs comfort-
the impact angle is less than 30° should be moved as far back as ably extended and their feet on
from the forward longitudinal axis possible. the floor until the vehicle is
of the vehicle. Additionally, the air • For maximum safety protection in parked and the ignition key is
bags will only deploy once. Seat all types of crashes, all occu- removed.
belts must be worn at all times. pants including the driver should • The SRS air bag system must
• Front air bags are not intended to always wear their seat belts deploy very rapidly to provide
deploy in side-impact, rear-impact whether or not an air bag is also protection in a crash. If an occu-
or rollover crashes. In addition, provided at their seating position pant is out of position because of
front air bags will not deploy in to minimize the risk of severe not wearing a seat belt, the air
frontal crashes below the deploy- injury or death in the event of a bag may forcefully contact the
ment threshold. crash. Do not sit or lean unneces- occupant causing serious or fatal
• A child restraint system must sarily close to the air bag while injuries.
never be placed in the front seat. the vehicle is in motion.
The infant or child could be (Continued)
severely injured or killed by an air
bag deployment in case of an
accident.
(Continued)
3 33
Why didn’t my air bag go off in a

collision? (Inflation and non-infla-
tion conditions of the air bag)
There are many types of accidents in
which the air bag would not be expect-
ed to provide additional protection.
These include rear impacts, second or
third collisions in multiple impact
accidents, as well as low speed
impacts.
OHR032100/OHR032101/OHR032102
Air bag collision sensors

(1) Front impact sensor
(2) SRS control module
3 34
(Continued)
WARNING
• Problems may arise if the sensor
• Do not hit or allow any objects to installation angles are changed
impact the locations where air due to the deformation of the
bags or sensors are installed. front bumper, body. We recom-
This may cause unexpected air mend that the system be serviced
bag deployment, which could by an authorized HYUNDAI deal-
result in serious personal injury er.
or death. • Your vehicle has been designed
• If the installation location or to absorb impact and deploy the
angle of the sensors is altered in air bag(s) in certain collisions.
any way, the air bags may deploy Installing bumper guards or
when they should not or they may OHR012031
replacing a bumper with non-gen-
not deploy when they should, uine parts may adversely affect Air bag inflation conditions
causing severe injury or death. your vehicle’s collision and air Front air bags
Therefore, do not try to perform bag deployment performance. Front air bags are designed to inflate in a
maintenance on or around the air frontal collision depending on the intensi-
bag sensors. We recommend that ty, speed or angles of impact of the front
the system be serviced by an collision.
authorized HYUNDAI dealer. Although the front air bags (driver’s and
(Continued) front passenger’s air bags) are designed
to inflate only in frontal collisions, they
also may inflate in other types of colli-
sions if the front impact sensors detect a
sufficient impact.
If the vehicle chassis is impacted by
bumps or objects on unimproved roads,
the air bags may deploy. Drive carefully
on unimproved roads or on surfaces not
designed for vehicle traffic to prevent
unintended air bag deployment.
3 35
OHR012032 OHR012033 OHR012035

Air bag non-inflation conditions • Frontal air bags are not designed to • Front air bags may not inflate in side
• In certain low-speed collisions the air inflate in rear collisions, because occu- impact collisions, because occupants
bags may not deploy. The air bags are pants are moved backward by the move to the direction of the collision,
designed not to deploy in such cases force of the impact. In this case, inflat- and thus in side impacts, frontal air bag
because they may not provide benefits ed air bags would not be able to pro- deployment would not provide addi-
beyond the protection of the seat belts vide any additional benefit. tional occupant protection.
in such collisions.
3 36
OHR012037 OHR012034 OHR012038

• In an angled collision, the force of • Just before impact, drivers often brake • Air bags may not inflate in rollover acci-
impact may direct the occupants in a heavily. Such heavy braking lowers the dents because air bag deployment
direction where the air bags would not front portion of the vehicle causing it to would not provide protection to the
be able to provide any additional bene- “ride” under a vehicle with a higher occupants.
fit, and thus the sensors may not ground clearance. Air bags may not
deploy any air bags. inflate in this "under-ride" situation
because deceleration forces that are
detected by sensors may be signifi-
cantly reduced by such “under-ride”
collisions.
3 37
SRS Care (Continued)

The SRS is virtually maintenance-free • No objects should be placed over
and so there are no parts you can safely or near the air bag modules on the
service by yourself. If the SRS air bag steering wheel, instrument panel,
warning light does not illuminate or if it and the front passenger's panel
continuously remains on, we recommend above the glove box, because any
that the system be inspected by an such object could cause harm if the
authorized HYUNDAI dealer. vehicle is in a crash severe enough
to cause the air bags to inflate.
• If the air bags inflate, we recom-
WARNING mend that the system be replaced
• Modification to SRS components by an authorized HYUNDAI dealer.
OHR012036 or wiring, including the addition • Do not tamper with or disconnect
• Air bags may not inflate if the vehicle of any kind of badges to the pad SRS wiring, or other components
collides with objects such as utility covers or modifications to the
of the SRS system. Doing so
poles or trees, where the point of body structure, can adversely
could result in injury, due to acci-
impact is concentrated to one area and affect SRS performance and lead
to possible injury. dental inflation of the air bags or
the full force of the impact is not deliv- by rendering the SRS inoperative.
ered to the sensors. • For cleaning the air bag pad cov-
ers, use only a soft, dry cloth or • If components of the air bag sys-
one which has been moistened tem must be discarded, or if the
with plain water. Solvents or vehicle must be scrapped, certain
cleaners could adversely affect safety precautions must be
the air bag covers and proper observed. An authorized
deployment of the system. HYUNDAI dealer knows these pre-
(Continued) cautions and can give you the
necessary information. Failure to
follow these precautions and pro-
cedures could increase the risk
of personal injury.
(Continued)
3 38
(Continued)
Additional safety precautions • Keep occupants away from the air
• Never let passengers ride in the bag covers. All occupants should sit
• If your car was flooded and has upright, fully back in their seats with
cargo area or on top of a folded-
soaked carpeting or water on the their seat belts on and their feet on the
down back seat. All occupants should
flooring, you shouldn't try to start floor. If occupants are too close to the
sit upright, fully back in their seats with
the engine; we recommend that air bag covers, they could be injured if
their seat belts on and their feet on the
you contact an authorized the air bags inflate.
floor.
HYUNDAI dealer. • Do not attach or place objects on or
• Passengers should not move out of
or change seats while the vehicle is near the air bag covers. Any object
moving. A passenger who is not wear- attached to or placed on the front air
ing a seat belt during a crash or emer- bag covers could interfere with the
gency stop can be thrown against the proper operation of the air bags.
inside of the vehicle, against other • Do not modify the front seats.
occupants, or out of the vehicle. Modification of the front seats could
• Each seat belt is designed to interfere with the operation of the sup-
restrain one occupant. If more than plemental restraint system sensing
one person uses the same seat belt, components.
they could be seriously injured or killed • Do not place items under the front
in a collision. seats. Placing items under the front
• Do not use any accessories on seat seats could interfere with the operation
belts. Devices claiming to improve of the supplemental restraint system
occupant comfort or reposition the seat sensing components and wiring har-
belt can reduce the protection provided nesses.
by the seat belt and increase the • Never hold an infant or child on your
chance of serious injury in a crash. lap. The infant or child could be seri-
• Passengers should not place hard ously injured or killed in the event of a
or sharp objects between them- crash. All infants and children should
selves and the air bags. Carrying be properly restrained in appropriate
hard or sharp objects on your lap or in child safety seats or seat belts in the
your mouth can result in injuries if an rear seat.
air bag inflates.
3 39
WARNING
• Sitting improperly or out of posi-
tion can cause occupants to be
shifted too close to a deploying
air bag, strike the interior struc- *
ture or be thrown from the vehicle
resulting in serious injury or
death.
• Always sit upright with the seat-
back in an upright position, cen-
tered on the seat cushion with
your seat belt on, legs comfort- OHR034106
ably extended and your feet on Air bag warning label
the floor.
Air bag warning labels are attached to
alert the driver and passengers of poten-
Adding equipment to or modifying tial risk of air bag system.
your air bag-equipped vehicle Note that these government warnings
If you modify your vehicle by changing focus on the risk to children, we also
your vehicle's frame, bumper system, wants you to be aware of the risks which
front end or side sheet metal or ride adults are exposed to.
height, this may affect the operation of
your vehicle's air bag system.
3 40
INSTRUMENT CLUSTER
■ Type A
1. Tachometer
2. Turn signal indicators
3. Speedometer
4. Engine coolant temperature gauge
5. Fuel gauge
6. Warning and indicator lights
7. Odometer/Tripmeter
■ Type B
8. LCD display* (including trip computer*)
* : if equipped
❈ The actual cluster in the vehicle may dif-

fer from the illustration.
OHR047224/OHR047225
3 41
■ Type A Speedometer (km or mile) ■ Type A

The speedometer indicates the forward
speed of the vehicle.
The speedometer is calibrated in miles
per hour and/or kilometers per hour.
OHR047218L
■ Type B
B330A01HR
■ Type B
OHR047214L
OHR047113
Tachometer
The tachometer indicates the approxi-
mate number of engine revolutions per
minute (rpm).
Use the tachometer to select the correct
shift points and to prevent lugging and/or
OHR047114L
over-revving the engine.
Gauges
3 42
When the door is open, or if the engine is

not started within 1 minute, the tachome- WARNING
ter pointer may move slightly in ON posi- Never remove the radiator cap
tion with the engine OFF. This movement when the engine is hot. The engine
is normal and will not affect the accuracy coolant is under pressure and
of the tachometer once the engine is run- could cause severe burns. Wait
ning. until the engine is cool before
adding coolant to the reservoir.
CAUTION
Do not operate the engine within
the tachometer's RED ZONE.
This may cause severe engine dam- OHR047216L
age.
Engine temperature gauge
This gauge shows the temperature of the
engine coolant when the ignition switch
is ON. Do not continue driving with an
overheated engine.
CAUTION
If the gauge pointer moves beyond
the normal range area toward the
“H” or “130” position, it indicates
overheating that may damage the
engine.
3 43
■ Type A On inclines or curves, the fuel gauge

pointer may fluctuate or the low fuel
warning light may come on earlier than
usual due to the movement of fuel in the
tank.
WARNING - Fuel gauge

Running out of fuel can expose
vehicle occupants to danger.
You must stop and obtain addition-
OHR047217L
■ Type B
al fuel as soon as possible after the
warning light comes on or when the OHR047118
gauge indicator comes close to the Trip computer (if equipped)
“E” or “0” level.
The trip computer is a microcomputer-
controlled driver information system that
displays information related to driving,
CAUTION including distance to empty, tripmeter
and average speed on the display when
Avoid driving with a very low fuel
the ignition switch is in the ON position.
level. If you run out of fuel, it could
cause the engine to misfire and All stored driving information (except
result in excessive loading of the odometer) is reset if the battery is dis-
OHR047115
catalytic converter. connected. The odometer is always dis-
Fuel gauge played until the display is turned off.
The fuel gauge indicates the approxi-
mate amount of fuel remaining in the fuel
tank. The fuel gauge is supplemented by
a low fuel warning light, which will illumi-
nate when the fuel tank is near empty.
3 44
Turn the MODE knob for less than 1 sec- ■ Type A ■ Type A
ond to select distance to empty, average
speed or tripmeter function as follows :
TRIP A
TRIP B
OHR047215L
■ Type B
OHR047219L
Distance to empty* ■ Type B
Average Fuel Economy*
* : if equipped
OHR047182
OHR047186
Odometer (km or mi)
The odometer Indicates the total dis-
tance that the vehicle has been driven
and should be used to determine when
periodic maintenance should be per-
formed.
OHR047183
- Odometer range : 0 ~ 1999999 kilome-
ters or miles. Tripmeter (km or miles)
3 45
This mode indicates the distance of indi- ■ Type B ✽ NOTICE

vidual trip since the last tripmeter reset. • If the vehicle is not on level ground or
The meter's working range is from 0.0 to the battery power has been interrupt-
999.9 km (miles). ed, the “Distance to empty” function
Turn the MODE knob for more than 1 may not operate correctly.
second when the tripmeter is being dis- The trip computer may not register
played clears the tripmeter to zero (0.0). additional fuel if less than 6 liters (1.6
gallons) of fuel are added to the vehicle.
• The fuel consumption and distance to
empty values may vary significantly
based on driving conditions, driving
habits, and condition of the vehicle.
OHR047184 • The distance to empty value is an esti-
Distance to empty (km or miles) mate of the available driving distance.
(if equipped) This value may differ from the actual
This mode indicates the estimated dis- driving distance available.
tance to empty based on the current fuel
in the fuel tank and the amount of fuel
delivered to the engine. When the remain-
ing distance is below 1 km (1 miles), “---”
will be displayed and the distance to
empty indicator will blink.
The meter’s working range is from 1 to
9999 km (1 to 9999 miles).
3 46
■ Type B Automatic reset Warning and indicator lights

The average fuel economy will be
cleared to zero (--.-) when the vehicle
speed exceeds 1.5 km/h after refueling WARNING
more than 6 liters (1.6 gallons). Never adjust the instrument cluster
while driving. This could result in
✽ NOTICE loss of control and lead to an acci-
dent that may cause death, serious
The average fuel economy is not dis- injury, or property damage.
played for more accurate calculation if
the vehicle does not drive more than 10
seconds or 50 meters (0.03 miles) since
the ignition switch or Engine Start/Stop
OHR047185
button is turned to ON. Turn Signal Indicator
Average Fuel Economy (if equipped) Lights
• The average fuel economy is calculat-
ed by the total driving distance and fuel
consumption since the last average fuel The blinking green arrows on the instru-
economy reset. ment panel show the direction indicated
- Fuel economy range: 0.0 ~ 99.9 by the turn signals. If the arrow comes on
L/100km or MPG but does not blink, blinks more rapidly
• The average fuel economy can be than normal, or does not illuminate at all,
reset both manually and automatically. a malfunction in the turn signal system is
indicated. Your dealer should be consult-
Manual reset ed for repairs.
To clear the average fuel economy man-
ually, turn MODE knob on instrument
cluster for more than 1 second when the
average fuel economy is displayed.
3 47
High Beam Indicator Anti-lock brake system ESC (Electronic Stability

Light (ABS) warning light Control) indicator
(if equipped) (if equipped)
The high beam indicator light comes on This warning light illuminates if the igni- The ESC indicator will illuminate when
whenever the headlights are switched to tion switch is turned to ON and goes off the ignition switch is turned ON, but
the high beam or flash position. in approximately 3 seconds if the system should go off after approximately 3 sec-
is operating normally. onds. When the ESC is on, it monitors
Air bag warning light If the ABS warning light remains on, the driving conditions. Under normal driv-
(if equipped) comes on while driving, or does not ing conditions, the ESC indicator will
come on when the ignition switch is remain off. When a slippery or low trac-
turned to the ON position, this indicates tion condition is encountered, the ESC
that the ABS may have malfunctioned. will operate, and the ESC indicator will
This warning light will illuminate for blink to indicate the ESC is operating.
approximately 6 seconds each time you If this occurs, we recommend that the
system be checked by an authorized But, if the ESC system malfunctions the
turn the ignition switch to the ON posi- indicator illuminates and stays on. We
tion. This light also comes on when the HYUNDAI dealer. The normal braking
system will still be operational, but with- recommend that the system be checked
Supplemental Restraint System (SRS) is by an authorized HYUNDAI dealer.
not working properly. If the SRS air bag out the assistance of the anti-lock brake
warning light does not come on, or con- system.
tinuously remains on after operating for ESC OFF indicator
about 6 seconds when you turned the (if equipped)
ignition switch to the ON position or start-
ed the engine, or if it comes on while
driving, we recommend that the system The ESC OFF indicator will illuminate
be inspected by an authorized HYUNDAI when the ignition switch is turned ON,
dealer. but should go off after approximately 3
seconds. To switch to ESC OFF mode,
press the ESC OFF button. The ESC
OFF indicator will illuminate indicating
the ESC is deactivated.
3 48
Immobilizer indicator Low Oil Pressure Warning Parking Brake/Low Brake

(if equipped) Light Fluid Level Warning Light
This light illuminates when the immobiliz-

er key is inserted and turned to the ON CAUTION WARNING
position to start the engine. If the oil pressure warning light If you suspect brake trouble, have
At this time, you can start the engine. The stays on while the engine is run- your brakes checked by a HYUNDAI
light goes out after the engine is running. ning, serious engine damage may dealer as soon as possible. Driving
If this light blinks when the ignition switch result. The oil pressure warning your car with a problem in either
is in the ON position before starting the light comes on whenever there is the brake electrical system or brake
engine, we recommend that the system insufficient oil pressure. In normal hydraulic system is dangerous, and
be checked by an authorized HYUNDAI operation, it should come on when could result in a serious injury or
dealer. the ignition switch is turned on, then death.
go out when the engine is started. If
the oil pressure warning light stays
Front fog light indicator on while the engine is running, there
(If Inatalled) may be a serious malfunction.
If this happens, stop the car as soon
as it is safe to do so, turn off the
This light comes on when the front fog engine and check the oil level. If the
lights are ON. oil level is low, fill the engine oil to
the proper level and start the engine
Rear fog light indicator again. If the light stays on with the
(If Inatalled) engine running, turn the engine off
immediately.
In any instance where the oil light
This indicator illuminates when the rear stays on when the engine is run-
fog lights are ON. ning, we recommend that the engine
be checked by an authorized
HYUNDAI dealer before the car is
driven again.
3 49
Warning Light Operation Your HYUNDAI is equipped with dual- Charging System Warning
The parking brake/low brake fluid level diagonal braking systems. This means Light
warning light should come on when the you still have braking on two wheels even
parking brake is applied and the ignition if one of the dual systems should fail.
switch is turned to "ON" or "START". With only one of the dual systems work-
ing, more than normal pedal travel and The charging system warning light
After the engine is started, the light
greater pedal pressure are required to should come on when the ignition is
should go out when the parking brake is
stop the car. Also, the car will not stop in turned on, then go out when the engine
released.
as short a distance with only half of the is running. If the light stays on while the
If the parking brake is not applied, the engine is running, there is a malfunction
brake system working. If the brakes fail
warning light should come on when the in the electrical charging system. If the
while you are driving, shift to a lower gear
ignition switch is turned to "ON" or light comes on while you are driving,
for additional engine braking and stop the
"START", then go out when the engine stop, turn off the engine and check under
car as soon as it is safe to do so.
starts. If the light comes on at any other the hood. First, make certain the genera-
time, you should slow the vehicle and tor drive belt is in place. If it is, check the
bring it to a complete stop in a safe loca- tension of the belt.
tion off the roadway.
And then, have the system checked by
The brake fluid level warning light indi- your HYUNDAI dealer.
cates that the brake fluid level in the
brake master cylinder is low and
hydraulic brake fluid conforming to DOT CAUTION
3 or DOT 4 specifications should be
added. After adding fluid, if no other trou- If the drive belt (generator belt) is
ble is found, the car should be immedi- loosen, broken, or mission while
ately and carefully driven to a HYUNDAI the vehicle is driving, there may be
dealer for inspection. If further trouble is a serious malfunction, engine could
experienced, the vehicle should not be overheat because this belt also
driven at all but taken to a dealer by a drives the water pump.
professional towing service or some
other safe method.
3 50
Door Ajar Warning Light Malfunction Indicator DPF warning light

and Chime (if equipped) Light (if equipped) (if equipped)
- Type A - Type B
The door ajar warning light warns you The MIL(Malfunction Indicator Light) illu- The warning message is displayed, as
that a door is not completely closed and minates when there are the malfunctions above, when there is a DPF problem with
the chime warns you that the key is in the in main sensors(such as pedal sensor, your vehicle, In this case, we recommend
ignition switch. booster sensor, etc.) or FIP(Fuel that the DPF system be inspected by an
Injection Pump) during driving. authorized HYUNDAI dealer.
Low Fuel Level Warning This light will illuminate when the ignition
Light key is turned from the "OFF" position to
the "ON" position, and will go out after CAUTION - Diesel engine
the engine starts. If it illuminates while (if equipped with DPF)
driving, or does not illuminate when the When the malfunction indicator
The low fuel level warning light comes on ignition key is turned from the "OFF" light is blinks, it may stop blinking
when the fuel tank is approaching empty. position to the "ON" position, we recom- after driving the vehicle at more
When it comes on, you should add fuel mend that the system be checked by an than 60km/h (37 mph) or at more
as soon as possible. Driving with the fuel authorized HYUNDAI dealer. than second gear with 1500 ~ 2500
level warning light on or with the fuel level engine rpm for a certain time (for
below "E" can cause the engine to mis- about 25 minutes).
fire and damage the catalytic converter. If the malfunction indicator light
continues to be blinked in spite of
the procedure, we recommend that
the system be checked by an
authorized HYUNDAI dealer.
If you continue to drive with the
malfunction indicator light blinking
for a long time, the DPF system can
be damaged and fuel consumption
can be worsen.
3 51
Seat Belt Warning Light Cruise Indicator Light

CAUTION - Diesel engine (if equipped) (if equipped) CRUISE
If the Emission Control System
Malfunction Indicator Light blinks,
some error related to the injection Seat belt warning light This indicator light illuminates:
quantity adjustment occurs which As a reminder to the driver or the front • When the cruise control system is
could result in loss of engine power, passenger (if equipped), the seat belt enabled.
combustion noise and poor emis- warning light will blink for approximately
sion. We recommend that the system 6 seconds each time you turn the ignition For more details, refer to “Cruise Control
be inspected by an authorized key to "ON" positon regardless of belt System” in chapter 5.
HYUNDAI dealer. fastening. If the driver's seat belt is unfas-
tened after the ignition key is turned to
the "ON" position, the seat belt warning Cruise SET Indicator Light
light blinks again for approximately 6 sec- (if equipped) SET
onds.
Seat belt warning chime This indicator light illuminates:

If the driver's seat belt or the front pas- • When the cruise control speed is set.
senger's seat belt (if equipped) are not
fastened when the ignition key is turned For more details, refer to “Cruise Control
to the ON position or if it is unfastened System” in chapter 5.
after the ignition key is turned to the "ON"
position, the seat belt warning chime will
sound for approximately 6 seconds. At
this time, if the seat belt is fastened, the
chime will stop at once.
3 52
Diesel Preheat Indicator Fuel Filter Warning Light Parking start warning sound
Light If the vehicle is driven at 10km/h(6mph)
for more 2~3 than seconds, the warning
chime will sound continuously when the
The indicator light illuminates amber This light illuminates when the ignition parking brake engaged.
when the ignition switch is placed at the switch is set to the "ON" position and
"ON" position. The engine can be started goes off after the engine has started. If it Over speed warning Buzzer
after the preheat indicator light goes off. lights up while the engine is running, it (if equipped)
The illuminating time varies with the indicates that water has accumulated When the car speed is in excess of 120
water temperature. inside the fuel filter. If this happens, km/h (75 mph), a buzzer will sound to
remove the water from the fuel filter. warn you.
Water temperature Illuminating time
(°C) (sec)
Brake pad wear warning sound
Below -30 22.5 The front disc brake pads have wear indi-
-20 82 cators that should make a high-pitched
squealing or scraping noise when new
-15 6 pads are needed. The sound may come
60 0.5 and go or be heard all the time when the
vehicle is moving. It may also be heard
80 0 when the brake pedal is pushed down
firmly. Excessive rotor damage will result
if the worn pads are not replaced. See
✽ NOTICE your HYUNDAI dealer immediately.
If the engine were not started within 2
seconds after the preheating is complet-
ed, turn the ignition key once more to
the "LOCK" position during 10 sec-
onds, and then to the "ON" position, in
order to preheat again
3 53
LIGHTING
Battery saver function ■ Type A ■ Type A
(if equipped)
• The purpose of this feature is to pre-
vent the battery from being dis-
charged. The system automatically
turns off the parking lights when the
driver removes the ignition key and
opens the driver-side door.
• With this feature, the parking lights will
ORBC040046 ORBC040047
be turned off automatically if the driver
■ Type B ■ Type B
parks on the side of road at night.
If necessary, to keep the lights on
when the ignition key is removed, per-
form the following:
1) Open the driver-side door.
2) Turn the parking lights OFF and ON
again using the light switch on the
steering column.
ORB040046E ORB040047E
CAUTION Lighting control Parking light position ( )

If the driver gets out of the vehicle The light switch has a Headlight and a When the light switch is in the parking
through other doors (except dri- Parking light position. light position, the tail, license and instru-
ver’s door), the battery saver func- To operate the lights, turn the knob at the ment panel lights are ON and the tail light
tion does not operate. Therefore, it end of the control lever to one of the fol- indicator is ON.
causes the battery to be dis- lowing positions:
charged. In this case, make sure to (1) OFF position ✽ NOTICE
turn off the lamp before getting out (2) Parking light position The ignition switch must be in the ON
of the vehicle.
(3) Headlight position position to turn on the instrument panel
lights.
3 54
■ Type A ■ Type A
WARNING
Do not use high beam when there
are other vehicles. Using high
beam could obstruct the other dri-
ver's vision.
ORBC040048 ORBC040049
■ Type B ■ Type B
ORB040048E ORB040049E
Headlight position ( ) High beam operation

When the light switch is in the headlight To turn on the high beam headlights,
position the head, tail, position, license push the lever away from you. Pull it back
and instrument panel lights are ON. for low beams.
The high beam indicator will light when
✽ NOTICE the headlight high beams are switched
on.
The ignition switch must be in the ON
To prevent the battery from being dis-
position to turn on the headlights.
charged, do not leave the lights on for a
prolonged
3 55
■ Type A ■ Type A Green arrow indicators on the instrument

panel indicate which turn signal is oper-
ating. They will self-cancel after a turn is
completed.
If the indicator continues to flash after a
turn, manually return the lever to the OFF
position.
To signal a lane change, move the turn
signal lever slightly and hold it in position
ORBC040050 (B). The lever will return to the OFF posi-
■ Type B tion when released.
If an indicator stays on and does not
ORBC040051 flash or if it flashes abnormally, one of the
■ Type A
turn signal bulbs may be burned out and
will require replacement.
✽ NOTICE
If an indicator flash is abnormally quick
or slow, a bulb may be burned out or
ORB040050E
have a poor electrical connection in the
Flashing headlights circuit.
To flash the headlights, pull the lever
towards you. It will return to the normal
(low beam) position when released. The
headlight switch does not need to be on ORB040051E
to use this flashing feature.
Turn signals and lane change signals
The ignition switch must be on for the
turn signals to function. To turn on the
turn signals, move the lever up or down
(A).
3 56
■ Type A Front fog light (if equipped) ✽ NOTICE

Fog lights are used to provide improved The ignition switch must be in the ON
visibility and avoid accidents when visibil- position to turn on the front fog light.
ity is poor due to fog, rain or snow etc.
The fog lights will turn on when fog light
switch (1) is turned to ON after the park-
ing light is turned on.
To turn off the fog lights, turn the switch
to OFF.
ORBC040052
■ Type B
CAUTION
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor or
unnecessary battery and generator
drain could occur.
ORB040052D
■ Type C
ORB040052E
3 57
■ Type A ■ Type C ✽ NOTICE

To turn on the rear fog light switch, the
ignition switch must be in the ON posi-
tion.
ORBC040053 ORB040053E
■ Type B ■ Type D
ORBC040052E ORB040053L
Rear fog light (if equipped)
To turn the rear fog lights on, turn the headlight switch to the headlight on position and
turn the rear fog light switch (1) to the on position.
The rear fog lights turn on when the rear fog light switch is turned on after the front
fog light switch is turned on and the headlight switch is in the parklight position.
To turn the rear fog lights off, turn the front fog light switch to the on position again or
turn the headlight switch off.
3 58
WIPERS AND WASHERS

Windshield wiper/washer A : Wiper speed control Windshield wipers
· MIST ( ) – Single wipe Operates as follows when the ignition
■ Type A
· OFF (O) – Off switch is turned ON.
· INT (---) – Intermittent wipe MIST ( ) : For a single wiping cycle,
· LO (1) – Low wiper speed push the lever upward and
· HI (2) – High wiper speed release it with the lever in
the OFF position. The
wipers will operate continu-
B : Intermittent wipe time adjustment
ously if the lever is pushed
upward and held.
C : Wash with brief wipes (front)* OFF (O) : Wiper is not in operation
INT (---) : Wiper operates intermittently
*: if equipped at the same wiping intervals.
Use this mode in a light rain or
■ Type B mist. To vary the speed setting,
turn the speed control knob.
LO (1) : Normal wiper speed
HI (2) : Fast wiper speed
✽ NOTICE
If there is heavy accumulation of snow or
ice on the windshield, defrost the wind-
shield for about 10 minutes, or until the
snow and/or ice is removed before using
the windshield wipers to ensure proper
operation.
If you do not remove the snow and/or ice
ORBC040054E/ORB040054E
before using the wiper and washer, it may
damage the Wiper and washer system.
3 59
■ Type A If the washer does not work, check the

washer fluid level. If the fluid level is not CAUTION
sufficient, you will need to add appropriate • To prevent possible damage to
non-abrasive windshield washer fluid to the wipers or windshield, do not
the washer reservoir. operate the wipers when the wind-
The reservoir filler neck is located in the shield is dry.
front of the engine compartment on the • To prevent damage to the wiper
passenger side. blades, do not use gasoline,
kerosene, paint thinner, or other
ORBC040056E solvents on or near them.
■ Type B CAUTION • To prevent damage to the wiper
To prevent possible damage to the arms and other components, do
washer pump, do not operate the not attempt to move the wipers
washer when the fluid reservoir is manually.
empty. • To prevent possible damage to
the wipers and washer system,
use anti-freezing washer fluids in
the winter season or cold weather.
WARNING
ORB040056E Do not use the washer in freezing
temperatures without first warming
Windshield washers the windshield with the defrosters;
In the OFF (O) position, pull the lever gen- the washer solution could freeze on
tly toward you to spray washer fluid on the contact with the windshield and
windshield and to run the wipers 1-3 obscure your vision.
cycles.
Use this function when the windshield is
dirty.
The spray and wiper operation will contin-
ue until you release the lever.
3 60
HEADLIGHT LEVELING DEVICE SYSTEM HAZARD WARNING SYSTEM

Loading condition Switch position
Driver only 0
Driver + Permissible
1
RR axle load
OHR027219L OHR047165L
(Left-hand Drive Type) The hazard warning system should be
(if equipped) used whenever you find it necessary to
To adjust the headlight beam level stop the car in a hazardous location.
according to the number of the passen- When you must make such an emer-
gers and the loading weight in the cargo gency stop, always pull off the road as far
area, turn the beam leveling switch. as possible.
The higher the number of the switch The hazard warning lights are turned on
position, the lower the headlight beam by pushing in the hazard switch. This
level. Always keep the headlight beam at causes all turn signal lights to blink. The
the proper leveling position, or headlights hazard warning lights will operate even
may dazzle other road users. though the key is not in the ignition.
Listed below are the examples of proper To turn the hazard warning lights off,
switch settings. For loading conditions push the switch a second time.
other than those listed below, adjust the
switch position so that the beam level
may be the nearest as the condition
obtained according to the list.
3 61
REAR WINDOW DEFROSTER SWITCH (IF EQUIPPED) TICKET HOLDER (IF EQUIPPED)
✽ NOTICE
The engine must be running for the rear
window defroster to operate.
OHR047176L OHR027104L
The rear window defroster is turned on For your convenience, it may be used for
by pushing in the switch. To turn the holding a tollgate ticket or a card.
defroster off, push the switch a second
time. The rear window defroster automat-
ically turns itself off after about 20 min-
utes. To restart the defroster cycle, push
in the switch again after it has turned
itself off.
CAUTION
Do not clean the inner side of the
rear window glass with an abrasive
type of glass cleaner or use a
scraper to remove foreign deposits
from the inner surface of the glass
as this may cause damage to the
defroster elements.
3 62
DIGITAL CLOCK (IF EQUIPPED) CIGARETTE LIGHTER

Reset:
Press the switch for more than 1 second
to reset minutes to ":00" or to facilitate
resetting the clock to the correct time.
When this is done:
Pressing the switch between 9 : 01 and 9
: 29 changes the readout to 9 : 00.
Pressing the switch between 9 : 30 and 9
: 59 changes the readout to 10 : 00.
Digital Clock Reset Switch

CAUTION
OHR047168 Don't turn the switch excessively to OHR047212L
There is a digital clock reset switch for prevent switch damage. For the cigarette lighter to work, the key
the digital clock. Its functions are: must be in the "ACC" position or the "ON"
position.
Hour/Minute Adjustment: To use the cigarette lighter, push it all the
way into its socket. When the element
Turn the switch counterclockwise for less
has heated, the lighter will pop out to the
than 1.5 seconds to advance the hour
"ready" position.
indicated. Turn the switch clockwise for
less than 1.5 seconds to advance the Do not hold the cigarette lighter pressed
minute indicated. in. This can damage the heating element
and create a fire hazard.
If it is necessary to replace the cigarette
Auto Mode: lighter, use only a genuine HYUNDAI
Turn the switch counterclockwise or replacement or its approved equivalent.
clockwise for more than 1.5 seconds to
advance the hour or the minute automat-
ically.
3 63
ASHTRAY ENGINE ILDE RPM ADJUST-

■ Type A
MENT KNOB (IF EQUIPPED)
WARNING
Do not insert foreign objects into
the socket of the cigarette lighter. It
may damage the cigarette lighter.
CAUTION
Do not use electric accessories or
equipment other than the HYUNDAI OHR027103L
genuine parts in the socket. ■ Type B
OHR047213L
When the outside air temperature is very

low or it is necessary to warm up the
engine, turn the knob clockwise to that
point at which the engine runs smoothly.
Once the warming up is completed, fully
turn the knob counterclockwise.
OHR047166L
CAUTION
The front ashtray may be opened by Never attempt to adjust the control
pulling it out by its grip. To remove the knob during driving.
ashtray to empty or clean it, press down
This can cause severe engine dam-
on the spring-loaded tab inside the ash-
age.
tray and pull it all the way out.
3 64
DRINK HOLDER (IF EQUIPPED) INTERIOR LIGHT

■ Type A
WARNING WARNING
• Use caution when using the drink Do not use the interior lights when
holders. A spilled beverage that driving in the dark. Accidents could
is very hot can injure you or your happen because the view may be
passengers. Spilled liquids can obscured by interior lights.
damage interior trim and electri-
cal components.
• Do not place anything except
drinks in the drink holder. Such
OHR057133 objects can be thrown out, possi-
■ Type B bly injuring persons in the vehi-
cle during sudden braking or in
the event of an accident.
WARNING
Keep cans or bottles out of direct
sun light and do not put them in a
vehicle that is heated up. It may
explode.
OHR044110
3 65
CAUTION
Do not leave the switch in this posi-
tion for an extended period of time
when the vehicle is not running.
• "OFF"
In the "OFF" position, the light stays off at
all times even though a door is open.
HHR2072 HHR2070
Map Light (if equipped, Interior Light (if equipped,
With Spectacle Case) Without Spectacle Case)
The map light has two kinds button. The The interior courtesy light switch has
two buttons are as follow: three positions. The three positions are:
• :
Push in this button to turn on or off the • "DOOR"
map light. In the "DOOR" position, the interior cour-
This light produces a spot beam for con- tesy light comes on when any door is
venient use as a map light at night or as opened regardless of the ignition key
a personal light for the driver and the position. The light goes out gradually 6
passenger. seconds after the door is closed.
• :
With this button pressed, both map lights • "On"
come on when any door is opened In the "ON" position, the light stays on at
regardless of the ignition key position. all times.
The light goes out gradually 6 seconds
after the door is closed.
3 66
SPECTACLE CASE (IF EQUIPPED) GLOVE BOX

■ Type A
WARNING
Do not put the glasses forcibly into
a sunglass holder to prevent break-
age or deformation of the glasses.
It may cause personal injury if you
try to open it forcibly when the
glasses are jammed in the holder.
OHR027105
■ Type B
HHR2108
The spectacle case is located on the
front overhead console.
Push the end of the cover to open the
spectacle case.
WARNING
Do not keep objects such as sharp
or unsuitable things inside the
spectacle case. Such objects can OHR027214
be thrown out in the event of a sud- To open the glove box, pull on the glove
den stop or an accident, possibly box release lever.
injuring the passengers in the vehi-
cle.
3 67
■ Type A
WARNING
• To avoid the possibility of injury
in case of an accident or a sud-
den stop, the glove box door
should be kept closed when the
car is in motion.
• Do not keep food in the glove box
for a long time.
B500C01HR
■ Type B
OHR047152
Pen, Card and Tissue Holder
For your convenience, a pen holder (1), a
card holder (2) and a tissue holder (3)
are located in the glove box cover.
3 68
CENTER SEATBACK CONSOLE COMPARTMENT (IF EQUIPPED)
L ev e r
B500B01HR HHR2107 HHR2114

Your vehicle is equipped with a console Multi Tray Coin Holder
compartment on the backside of front The multi tray is used for storing cassette The coin holder is used to store coins.
center seat. tapes or small articles.
To use console compartment, push down To open the multi tray lid, press the hook
the lever and tilt the seatback forward. in the lid's grip and pull up the lid.
3 69
OUTSIDE REARVIEW MIRROR
CAUTION
If the mirror control is jammed with
ice, do not attempt to break it free
using the control handle or by
manipulating the face of the mirror.
Use an approved spray de-icer (not
radiator antifreeze) to release the
frozen mechanism or move the
vehicle to a warm place and allow
the ice to melt.
HHR2134 OHR022136
Manual Type WARNING Folding the Outside Rearview
Before driving away, always check that Be careful when judging the size or Mirrors
your mirrors are positioned so you can distance of any object seen in the To fold the outside rearview mirrors, push
see behind you, both to the left and right rearview mirror. It is a convex mir- them towards the rear.
sides, as well as directly behind your ror with a curved surface. Any The outside rearview mirrors can be fold-
vehicle. When using the mirror, always objects seen in this mirror are closed rearward for parking in narrow areas.
exercise caution when attempting to er than they appear.
judge the distance of vehicles behind or Check your inside rearview mirror
along side of you. or glance over your shoulder WARNING
before changing lanes. Do not adjust or fold the outside
✽ NOTICE rearview mirrors while the vehicle
There is the assist convex mirror at the is moving. This could result in loss
under side of driver's outside rearview of control, and an accident which
mirror. You can take a better look at the could cause death, serious injury
dead zone. But, the object seems to be or property damage.
distorted.
3 70
DAY/NIGHT INSIDE PARKING BRAKE

REARVIEW MIRROR
CAUTION
• Driving with the parking brake
applied will cause excessive
brake pad (or lining) and brake
rotor wear.
• Do not operate the parking brake
while the vehicle is moving
except in an emergency situation.
It could damage the vehicle sys-
tem and make endanger driving
safety.
HHR3033
HHR2057
Applying the parking brake Releasing the parking brake
Your HYUNDAI is equipped with a To engage the parking brake, first apply To release the parking brake, first apply
day/night inside rearview mirror. The the foot brake and then without pressing the foot brake and pull the parking brake
"night" position is selected by flipping the the release button in, pull the parking lever slightly. Secondly, depress the
tab at the bottom of the mirror toward brake lever up as far as possible. In addi- release button and lower the parking
you. In the "night" position, the glare of tion it is recommended that when parking brake lever while holding the button.
headlights of cars behind you is reduced. the vehicle on a gradient, the shift lever
should be positioned in the appropriate
low gear on manual transaxle vehicles or
in the P (Park) position on automatic
WARNING transaxle vehicles.
Do not modify the inside mirror and
don’t install a wide mirror. It could
result in injury, during an accident
or deployment of the air bag.
3 71
HOOD RELEASE
4. Check that the hood has engaged
properly. If the hood can be raised
slightly, it is not properly engaged.
Open it again and close it whit a little
more force.
Make sure the hood is properly locked
before driving.
✽ NOTICE
If the hood will not open because ice has
formed around it, tap lightly or push on
the hood to break the ice and release the
B570A01HR OHR022040
hood. Do not pry on the hood. If neces-
1. Pull the release knob to unlatch the 2. Push the secondary latch lever to the sary, spray around the hood with an
hood. left and lower the hood. approved de-icer fluid (do not use radi-
ator anti-freeze) or move the vehicle to a
Closing the hood warm place and allow the ice to melt.
WARNING
Open the hood after turning off the 1. Before closing the hood, check the fol-
engine on a flat surface, shifting lowing: WARNING
the shift lever to the 1st(First) gear • All filler caps in the under hood area • Always double check to be sure
or R(Reverse) for manual transaxle, must be correctly installed. that the hood is firmly latched
and setting the parking brake. • Jack must be secured in its retainer to before driving away. Driving with
prevent it from ratting (for 1 Ton only). the hood opened may cause a
2. Secure the support rod in its clip. total loss of visibility, which
3. Lower the hood to about 30 cm (12 might result in an accident.
inches) height and push down to • Do not press excessively or step
securely lock in place. Then double on the hood. This can cause the
check to be sure the hood is secure. hood to fall and result in serious
injury.
3 72
FUEL TANK CAP

(Continued)
WARNING
• Do not get back in the vehicle
• Fuel vapors are dangerous. while refueling. Do not operate
Before refueling, always stop the anything that can produce static
engine and never allow sparks or electricity. Static electricity dis-
open flames near the tank area. If charge can ignite fuel vapors
you need to replace the tank cap, resulting in an explosion.
use a genuine HYUNDAI replace-
ment part. • When using a portable fuel con-
tainer, be sure to place the con-
If you open the fuel tank cap dur- tainer on the ground while refuel-
ing high ambient temperatures, a ing. Static electricity discharge
slight "pressure sound" may be from the container can ignite fuel
HHR2036 heard. This is normal and not a vapors causing a fire. While start-
The fuel tank cap is located at the left cause for concern. Whenever you ing refueling, contact should be
side of the vehicle body. open the fuel tank cap, turn it maintained until the filling is com-
The fuel tank cap can be unlocked by slowly. plete.
turning the key counterclockwise. • Automotive fuels are flamma- • Do not use cellular phones around
To lock the fuel tank cap, turn it clockwise ble/explosive materials. When a gas station. The electric current
until it locks into place. refueling, please note the follow- or electronic interference from
ing guidelines carefully. cellular phones can ignite fuel
• Before touching the fuel nozzle or
✽ NOTICE fuel tank cap, have one's hands in
vapors causing a fire.
If the fuel tank cap will not open • When refueling, always turn the
contact with metal parts away engine off. Sparks by engine com-
because ice has formed around it, tap from the tank neck to discharge
lightly on the cap to break the ice and partment electrical equipment can
static electricity. ignite fuel vapors causing a fire.
release the cap. If necessary, spray
(Continued) After refueling, check to make
around the cap with an approved de-
icer fluid (do not use radiator anti- sure the fuel tank cap is securely
freeze) or move the vehicle to a warm closed, and then start the engine.
place and allow the ice to melt. • Do not smoke or try to light ciga-
rettes around a gas station.
Automotive fuels are flammable.
3 73
REAR GATE
HHR2025 OHR022106 HHR2031

To open the rear gate 2.Lower the rear gate slowly with it To close the rear gate
1. Lift up the rear gate handle, push it received on both arms. Lift the rear gate up and lock the rear
inside and pull it toward you. gate handle in place.
WARNING
When the rear combination lamps
are hidden, other road users should
be warned by means of warning tri-
angle or other devices.
3 74
SIDE GATE
SUPPORT
SUPPORT BAR
BAR
HHR2026 OHR022117 OHR022118

To open the side gate 2. Remove the side gate handle from the To close the side gate
1. With the rear gate opened, pull up the hook after pulling it up. 1. Lift the side gate up and lock the side
knob to release the support bar down. 3. Lower the side gate slowly with it gate handle in place.
received on both arms.
WARNING
When locking the side gate handle,
be careful not to get your fingers
into the chink in the handle.
3 75
EXTERIOR TOOL BOX SUN VISOR

(IF EQUIPPED)
OHR022119 OHR028107
2. Push the knob down to lock the side OHR048100 Your HYUNDAI is equipped with sun
gates. The exterior tool box is located behind visors to give the driver and front pas-
the rear tire on left side to store jack and senger either frontal or sideward shade.
tool. To reduce glare or to shut out direct rays
To open it, pull up the clamp lever (1) and of the sun, turn the sun visor down. Ticket
unhook the clamp. holders are provided on the back of the
sun visor for the driver and front passen-
ger.
WARNING
• Do not place the sun visor in
such a manner that it obscures
visibility of the roadway, traffic or
other objects.
• For your safety, do not obstruct
your vision when using the sunvi-
sor.
3 76
STEERING WHEEL
Power steering (if equipped) ✽ NOTICE
Power steering uses energy from the If the power steering drive belt breaks
engine to assist you in steering the vehi- or if the power steering pump malfunc-
cle. If the engine is off or if the power tions, the steering effort will greatly
steering system becomes inoperative, increase.
the vehicle may still be steered, but it will
require increased steering effort. ✽ NOTICE
Should you notice any change in the If the vehicle is parked for extended
effort required to steer during normal periods outside in cold weather (below
vehicle operation, we recommend that -10°C/14°F), the power steering may
the system be checked by an authorized require increased effort when the engine
HYUNDAI dealer. is first started. This is caused by
increased fluid viscosity due to the cold
weather and does not indicate a mal-
CAUTION function.
Never hold the steering wheel to the When this happens, increase the engine
extreme right or left for more than 5 RPM by depressing the accelerator until
seconds with the engine running. the RPM reaches 1,500 rpm then release
Holding the steering wheel for more or let the engine idle for two or three
than 5 seconds in either position minutes to warm up the fluid.
may cause damage to the power
steering pump.
3 77
OHR027108L OHR027055L OHR047162L

Steering wheel tilt lever Horn Heated steering wheel (if equipped)
(if equipped) Press the center hub of the steering With the ignition switch in the ON posi-
To Adjust the Steering Wheel: wheel to sound the horn. tion, pressing the heated steering wheel
1. Push the lever and hold it to unlock. button warms the steering wheel.
2. Raise or lower the steering wheel to The indicator on the button will illuminate.
the desired position. To turn the heated steering wheel off,
press the button once again. The indica-
3. After adjustment, release the lever.
tor on the button will turn off.
WARNING ✽ NOTICE
Do not attempt to adjust the steer- The heated steering wheel will turn off
ing wheel while driving as this may automatically approximately 30 minutes
result in loss of control of the vehi- after the heated steering wheel is turned on.
cle which may cause serious injury
or death.
CAUTION
Do not install any grip to operate the
steering wheel. This causes damage
to the heated steering wheel system.
3 78
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)

■ Type A ■ Type B
1. Air flow control switch

2. Fan speed control switch
3. Temperature control switch
4. Air intake control switch
5. Air conditioning switch

HHR2017/OHR047143
3 79
Center ventilator
The center ventilators are located in the
middle of the dashboard. The direction of
air flow from the vents in the center of the
dashboard is adjustable.
To control the direction of the air flow,
move the knob in the center of the vent
up-and-down and side-to-side.
Side ventilator
The side ventilators are located on each
side of dashboard. To change the direc-
tion of the air flow, move the knob in the
center of the vent up-and-down and side-
to-side.
The vents are opened when the vent
knob is moved to " " position. The
vents are closed when the vent knob is
moved to " ". Keep these vents clear
of any obstructions.
OHR017003L
1. Side Defrost Nozzle CAUTION

2. Side Ventilator Operating the blower when the igni-
3. Windshield Defrost Nozzle tion switch is in the ON position
4. Center Ventilator could cause the battery to dis-
charge. Operate the blower when
the engine is running.
3 80
OHR027111 OHR027112 OHR027113

Face-Level Bi-Level Floor-Level
Selecting the "Face" mode will cause air Air is discharged through the face vents Air is discharged through the floor vents,
to be discharged through the face level and the floor vents. This makes it possi- windshield defroster nozzle, side
vents. ble to have cooler air from the dashboard defroster nozzle, side ventilator.
vents and warmer air from the floor out-
lets at the same time.
3 81
■ Type A
HHR2080
■ Type B
OHR027114 OHR027115
Floor-Defrost Level Defrost-Level
Air is discharged through the windshield Air is discharged through the windshield
defroster nozzle, the floor vents, side defroster nozzle, side defroster nozzle,
defroster nozzle, side ventilator. side ventilator.
OHR047131
Air Flow Control
This is used to direct the flow of air. Air
can be directed to the floor, dashboard
outlets, or windshield. Five symbols are
used to represent Face, Bi-Level, Floor,
Floor-Defrost and Defrost air position.
3 82
■ Type A ■ Type A ■ Type A
HHR2086 OHR043100 HHR2087

■ Type B ■ Type B ■ Type B
OHR047135 OHR047135L OHR047137

Fan Speed Control To turn off the blowers Temperature Control
(Blower Control) To turn off the blowers, turn the fan This control is used to adjust the degree
This is used to turn the blower fan on or speed control knob to the "0" position. of heating or cooling desired.
off and to select the fan speed.
This blower fan speed, and therefore the
volume of air delivered from the system,
may be controlled manually by setting
the blower control between the "1" and
"4" positions.
3 83
■ Type A FRESH MODE : ✽ NOTICE

■ Type A ■ Type B Prolonged operation of the heater in the
recirculated air position (without air
conditioning selected) may cause fogging
of the windshield and side windows and
the air within the passenger compart-
With the outside (fresh) air position select- ment may become stale.
ed, air enters the vehicle from outside and In addition, prolonged use of the air con-
is heated or cooled according to the func- ditioning with the recirculated air posi-
tion selected. tion selected will result in excessively dry
OHR022116L
air in the passenger compartment.
■ Type B RECIRCULATION MODE :
■ Type A ■ Type B WARNING
• Continue using the climate con-
trol system in the recirculated air
position may allow humidity to
increase inside the vehicle which
With the recirculated air position select-
may fog the glass and obscure
ed, air from the passenger compartment
visibility.
will be drawn through the heating system
and heated or cooled according to the • Do not sleep in a vehicle with the
function selected. air conditioning or heating sys-
OHR047139 tem on. It may cause serious
harm or death due to a drop in the
Air Intake Control oxygen level and/or body temper-
This is used to select fresh outside air or ature.
recirculating inside air. • Continue using the climate control
To change the air intake control mode system in the recirculated air posi-
(Fresh mode, Recirculation mode), push tion can cause drowsiness or
the control button. sleepiness, and loss of vehicle
control. Set the air intake control
to the outside (fresh) air position
as much as possible while driving.
3 84
System operation Bi-level heating Defrosting/defogging

Heating control Your HYUNDAI is equipped with bi-level Use the heating/ventilation system to
For normal heating operation, set the air heating controls. This makes it possible defrost or defog the windshield:
intake control to the fresh air ( / ) to have cooler air from the dashboard
position and the air flow control to the floor vents and warmer air from the floor out-
To remove interior fog on the wind-
( ) position. lets at the same time. To use this feature:
shield:
• Set the air flow control to the defrost
• Set the air intake control to the fresh air ( ) position.
For faster heating, the air intake control
( / ) position.
should be set in the recirculate ( / ) • If the vehicle is equipped with a air
position. • Set the air flow control at the bi-level conditioning system, turn on the air
( ) position. conditioning switch.
• Set the temperature control between • Set the air intake control to the fresh air
If the windows fog up, set the air flow con-
"Cool" and "Warm". ( / ) position.
trol to the defrost ( ) position and the air
intake control to the fresh air ( / ) • Set the fan speed control between "1"
Ventilation and "4" position.
position.
To operate the ventilation system: • Set the temperature control to the
• Set the air intake control to "Fresh" desired position.
For maximum heat, move the temperature
control to "Warm". mode ( / ).
• To direct all intake air to the dashboard
vents, set the air flow control to "Face".
• Adjust the fan speed control to the
desired speed.
• Set the temperature control between
"Cool" and "Warm".
3 85
To remove the frost or exterior fog on Operation Tips ■ Type A

the windshield: • To keep dust or unpleasant fumes from
• Set the air flow control to the defrost entering the car through the ventilation
( ) position. system, temporarily set the air intake
• If the vehicle is equipped with a air control at "Recirculation ( / )".
conditioning system, turn on the air Be sure to return the control to "Fresh
conditioning switch. ( / )" when the irritation has
• Set the air intake control to the fresh passed to keep fresh air in the vehicle.
( / ) position. This will help keep the driver alert and
• Set the fan speed control to position comfortable.
"3" or "4". • Air for the heating/cooling system is OHR022109L
• Set the temperature control to warm. drawn in through the grilles just ahead ■ Type B
of the windshield. Care should be
taken that these are not blocked by
✽ NOTICE leaves, snow, ice or other obstructions.
When the A/C is operated continuously • To prevent interior fog on the wind-
on the floor-defrost level ( ) or shield, set the air intake control to the
defrost level ( ), it may cause fog to fresh air ( / ) position, fan speed
form on the exterior windshield. If this to the desired position, turn on the air
occurs, set the air flow control to the conditioning system, and adjust tem-
perature control to desired tempera-
face level position ( ) and fan speed ture.
control to the low position. OHR047133
Air conditioning system
Air Conditioning Switch (if equipped)
The air conditioning is turned on by push-
ing the A/C button on the heating/air con-
ditioning control panel.
3 86
Air Conditioning Operation (Cooling) De-Humidified Heating Operation Tips

To use the air conditioning to cool the For dehumidified heating: • If the interior of the car is hot when you
interior: • Turn on the fan control switch (2). first get in, open the windows for a few
• Turn on the fan control switch (2). minutes to expel the hot air.
• Turn on the air conditioning switch (5).
• Turn on the air conditioning switch (5) The air conditioning indicator light • When you are using the air condition-
by pushing in on the switch. should come on at the same time. ing system, keep all windows closed to
The air conditioning indicator light keep hot air out.
• Set the air intake control (4) to the
should come on at the same time. fresh air ( / ) position. • When moving slowly, as in heavy traf-
• Set the air intake control (4) to the fic, shift to a lower gear.
• Set the air flow control (1) to the face
/ position. This increases engine speed, which in
( ) position.
• Set the temperature control (3) to turn increases the speed of the air con-
• Adjust the fan control (2) to the desired ditioning compressor.
"Cool". ("Cool" provides maximum speed.
cooling. The temperature may be mod- • On steep grades, turn the air condi-
• For more rapid action, set the fan at tioning off to avoid the possibility of the
erated by moving the control toward
one of the higher speeds. engine over-heating.
"Warm".)
• Adjust the temperature control (3) to • During winter months or in periods
• Adjust the fan control (2) to the desired
provide the desired amount of warmth. when the air conditioning is not used
speed. For greater cooling, turn the fan
control to one of the higher speeds or regularly, run the air conditioning once
temporarily select the / posi- every month for a few minutes.
tion on the air intake control. This will help circulate the lubricants
and keep your system in peak operat-
ing condition.
3 87
CAUTION
Outside air • If the car is being driven in severe
conditions such as dusty, rough
Inside of roads, more frequent climate con-
a vehicle Filter trol air filter inspections are
required.
• When the air flow rate is
decreased, we recommend that
the system be checked by an
Evaporator core Blower authorized HYUNDAI dealer.
Inside air
B760A01HR
Climate control air filter (for evap-
orator and blow unit) (if equipped)
The climate control air filter is located in
the hood. It operates to decrease the
amount of pollutants entering the car.
3 88
Multimedia system / 4-2
Audio / 4-5
Multimedia System 4
Multimedia System
MULTIMEDIA SYSTEM
✽ NOTICE FM reception AM (MW, LW) reception
• If you install an aftermarket HID
headlamp, your vehicle's audio and
electronic device may malfunction.
• Prevent chemicals such as perfume,
cosmetic oil, sun cream, hand cleaner,
and air freshener from contacting the
interior parts because they may cause
damage or discoloration.
JBM001 JBM002
How vehicle audio works AM broadcasts can be received at
AM and FM radio signals are broadcast greater distances than FM broadcasts.
from transmitter towers located around This is because AM radio waves are
your city. They are intercepted by the transmitted at low frequencies. These
radio antenna on your vehicle. This signal long, low frequency radio waves can fol-
is then received by the radio and sent to low the curvature of the earth rather than
your vehicle speakers. travelling straight out into the atmos-
phere. In addition, they curve around
When a strong radio signal has reached
obstructions so that they can provide bet-
HHR2137 your vehicle, the precise engineering of
ter signal coverage.
Manual Antenna your audio system ensures the best pos-
sible quality reproduction. However, in
Your car uses a manual stainless steel some cases the signal coming to your
antenna to receive both AM and FM broad- vehicle may not be strong and clear. This
cast signals. Pull up the antenna using your can be due to factors such as the dis-
fingers, as shown in the drawing. tance from the radio station, closeness of
✽ NOTICE other strong radio stations or the pres-
ence of buildings, bridges or other large
Before entering an automatic car wash or obstructions in the area.
a place with a low height clearance, be
sure that the antenna is fully retracted.
4 2
Multimedia System
FM radio station
JBM003 JBM004 JBM005

FM broadcasts are transmitted at high • Fading - As your vehicle moves away • Station Swapping - As a FM signal
frequencies and do not bend to follow the from the radio station, the signal will weakens, another more powerful sig-
earth's surface. Because of this, FM weaken and sound will begin to fade. nal near the same frequency may
broadcasts generally begin to fade at When this occurs, we suggest that you begin to play. This is because your
short distances from the station. select another stronger station. radio is designed to lock onto the clear-
Also, FM signals are easily affected by • Flutter/Static - Weak FM signals or est signal. If this occurs, select another
buildings, mountains, or other obstruc- large obstructions between the trans- station with a stronger signal.
tions. These can result in certain listening mitter and your radio can disturb the • Multi-Path Cancellation - Radio signals
conditions which might lead you to signal causing static or fluttering nois- being received from several directions
believe a problem exists with your radio. es to occur. Reducing the treble level can cause distortion or fluttering. This
The following conditions are normal and may lessen this effect until the distur- can be caused by a direct and reflect-
do not indicate radio trouble: bance clears. ed signal from the same station, or by
signals from two stations with close
frequencies. If this occurs, select
another station until the condition has
passed.
4 3
Multimedia System
Using a cellular phone or a two-way Care of disc ✽ NOTICE - Playing an

radio • If the temperature inside the car is too Incompatible Copy Protected
When a cellular phone is used inside the high, open the car windows to ventilate Audio CD
vehicle, noise may be produced from the before using the system. Some copy protected CDs, which do not
audio equipment. This does not mean • It is illegal to copy and use MP3/WMA comply with international audio CD
that something is wrong with the audio files without permission. Use CDs that standards (Red Book), may not play on
equipment. In such a case, use the cellu- are created only by lawful means. your car audio. Please note that inabili-
lar phone at a place as far as possible ties to properly play a copy protected
• Do not apply volatile agents, such as
from the audio equipment. CD may indicate that the CD is defec-
benzene and thinner, normal cleaners
and magnetic sprays made for ana- tive, not the CD player.
CAUTION logue disc onto CDs.
When using a communication sys- • To prevent the disc surface from get-
tem such a cellular phone or a radio ting damaged, hold CDs by the edges
set inside the vehicle, a separate or the center hole only.
external antenna must be fitted. • Clean the disc surface with a piece of
When a cellular phone or a radio set soft cloth before playback (wipe it from
is used with an internal antenna the center to the outside edge).
alone, it may interfere with the vehi- • Do not damage the disc surface or
cle's electrical system and adversely attach pieces of sticky tape or paper.
affect safe operation of the vehicle. • Make certain only CDs are inserted
into the CD player (Do not insert more
than one CD at a time).
• Keep CDs in their cases after use to
WARNING protect them from scratches or dirt.
Don't use a cellular phone when • Depending on the type of CD-R/CD-
you are driving. You should stop at RW CDs, certain CDs may not operate
a safe place to use a cellular phone. normally according to manufacturing
companies or making and recording
methods. In such circumstances, con-
tinued use may cause malfunctions to
your audio system.
4 4
Multimedia System
AUDIO (Without Touch Screen)
4FN3G0000EG
4 5
Multimedia System
Feature of Your Audio (1) EJECT (5) SEEK/TRACK

• Ejects the disc. When pressed quickly
Head Unit • Radio mode: Searches broadcast fre-
(2) FM quencies.
• Plays FM radio. • Media mode: Changes the track, file or
title. (except AUX)
(3) AM When pressed and held
• Plays AM radio. • Radio mode: Frequency is controlled
by 1 step quickly. When the button is
(4) MEDIA released after pressing and holding,
• Plays Media(Disc, USB(iPod®), AUX) searches broadcast frequencies.
mode. • Media mode: Rewinds or fast-forwards
• Each time the button is pressed, the the song. (except AUX)
media mode popup will be displayed or
closed. (6) POWER/VOLUME knob
• The media mode popup will not be dis- • Power: Turns power On/Off by pressing
played when [SETUP] button the knob.
[Display] [Mode popup] is turned • Volume: Sets volume by turning the
❈ The actual features in the vehicle may
[Off]. knob left/right.
differ from the illustration.
4 6
Multimedia System
(10) BACK
• Moves to previous screen.
(11) FOLDER
• Media(MP3 CD, USB) mode: Searches (13) [1] ~ [6] (Preset)
folders. When pressed quickly
• Radio mode: Receives saved frequen-
(12) TUNE knob cies(channels).
• Radio mode: Changes frequency by • Media mode(USB, MP3 CD)
turning the knob left/right. - [RPT] button: Repeat/Repeat Folder
• Media mode: Searches songs(files) by - [SHFL] button: Shuffle Folder/Shuffle
turning the knob left/right. • Media mode(iPod®, Audio CD)
- [RPT] button: Repeat
- [SHFL] button: Shuffle
(7) DISP • In case of Menu popup, the number
• Turns off the screen. menu is selected.
• Each time the button is pressed, it sets When pressed and held
the Screen Off ➟ On ➟ Off. • Radio mode: Saves frequencies (chan-
nels).
(8) SETUP
When pressed quickly
• Moves to Setup screen.
(9) MENU
• Displays menus for the current mode.
4 7
Multimedia System
Steering Wheel Controls (1) SEEK/TRACK (3) MUTE

• When pressed quickly • Mutes the audio volume.
- Radio mode: Searches broadcast
frequencies saved to Presets. (4) VOLUME
- Media mode: Changes track, file or • Controls the audio volume.
title. (except AUX)
• When pressed and held
- Radio mode: Frequency is controlled
by 1 step quickly. When the button is
released after pressing and holding,
searches broadcast frequencies.
- Media mode: Rewinds or fast-for-
wards the song. (except AUX)
(2) MODE
❈ The actual features in the vehicle may • Each time this is pressed, the mode is
differ from the illustration. changed sequentially.
• If the media is not connected, the cor-
responding modes will be disabled.
• Press and hold to turn the Audio system
on/off.
• When power is off, press button to turn
power back on.
4 8
Multimedia System
Radio Change Frequency: TUNE knob FM/AM Mode

Changes frequency by turning the knob
Radio Mode left/right. You can seek available frequen-
Change Mode: [FM], [AM] button cies manually.
• You can change the radio mode
through [FM], [AM] button. Saved Frequency: PRESET [1] ~ [6] but-
tons
• The radio mode popup will not be dis-
played when [SETUP] button • Pressing the button: Plays the frequen-
[Display] [Mode popup] is turned cy saved in the corresponding button.
[Off]. • Pressing and holding the button: Saves
the currently playing broadcast to the Select Menu: [MENU] button
selected button and sound a BEEP. Displays Menu Popup when pressing the
Search Frequency: [SEEK/TRACK] but-
[MENU] button.
ton
• Auto Store: Saves broadcasts with
Searches the previous/next broadcast
superior reception to [1] ~ [6] buttons.
frequencies.
If no frequencies are received, then the
• Pressing the button: Changes the fre- most recently received frequency will
quency. be broadcast.
• Pressing and holding the button: When • Scan: The broadcast frequency
the button is released after pressing increases and previews each broad-
and holding, searches broadcast fre- cast for 5 seconds each. After scan-
quencies. ning all frequencies, returns and plays
the current broadcast frequency.
• Sound Settings: Moves to Sound
Settings.
4 9
Multimedia System
Media ✽ NOTICE - Playing an

Incompatible Copy Protected
✽ NOTICE - Using the Discs Audio CD
• If the temperature inside the car is too Some copy protected CDs, which do not
high, open the car windows to ventilate comply with international audio CD
before using the system. standards (Red Book), may not play on
• It is illegal to copy and use MP3/WMA your car audio. Please note that inabili-
files without permission. Use CDs that ties to properly play a copy protected
are created only by lawful means. CD may indicate that the CD is defec-
• Do not apply volatile agents, such as tive, not the CD player.
benzene and thinner, normal cleaners
and magnetic sprays made for ana- NOTE:
logue disc onto CDs. Order of playing files (folders):
• To prevent the disc surface from get- 1. Song playing order: to
ting damaged, hold CDs by the edges sequentially.
or the center hole only. 2. Folder playing order:
• Clean the disc surface with a piece of ❋ If no song file is contained in the
soft cloth before playback. (wipe it folder, that folder is not displayed.
from the center to the outside edge)
• Do not damage the disc surface or
attach pieces of sticky tape or paper.
• Make certain only CDs are inserted
into the CD player. (Do not insert more
than one CD at a time)
• Keep CDs in their cases after use to
protect them from scratches or dirt.
• Depending on the type of CD-R/CD-
RW CDs, certain CDs may not operate
normally according to manufacturing
companies or making and recording
methods. In such circumstances, con-
tinued use may cause malfunctions to
your audio system.
4 10
Multimedia System
(Continued)
WARNING WARNING
• Do not touch the antenna during
• Do not stare at the screen while thunder or lightening as such Driving while distracted can result
driving. Staring at the screen for acts may lead to lightning in a loss of vehicle control that may
prolonged periods of time could induced electric shock. lead to an accident, severe person-
lead to traffic accidents. al injury, and death. The driver’s pri-
• Do not stop or park in parking- mary responsibility is in the safe
• Do not disassemble, assemble, or restricted areas to operate the
modify the audio system. Such and legal operation of a vehicle,
product. Such acts could lead to and use of any handheld devices,
acts could result in accidents, traffic accidents.
fire, or electric shock. other equipment, or vehicle sys-
• Use the system with the vehicle tems which take the driver’s eyes,
• Using the phone while driving ignition turned on. Prolonged use
may lead to a lack of attention of attention and focus away from the
with the ignition turned off could safe operation of a vehicle or which
traffic conditions and increase result in battery discharge.
the likelihood of accidents. Use are not permissible by law should
the phone feature after parking never be used during operation of
the vehicle. the vehicle.
• Heed caution not to spill water or
introduce foreign objects into the
device. Such acts could lead to
smoke, fire, or product malfunc-
tion.
• Please refrain from use if the
screen is blank or no sound can
be heard as these signs may indi-
cate product malfunction.
Continued use in such conditions
could lead to accidents (fires,
electric shock) or product mal-
functions.
(Continued)
4 11
Multimedia System
✽ NOTICE (Continued) ✽ NOTICE - Using MP3

• Operating the device while driving • Do not subject the device to severe Supported audio formats
could lead to accidents due to a lack of shock or impact. Direct pressure onto
attention to external surroundings. the front side of the monitor may
First park the vehicle before operat- cause damage to the LCD or touch
ing the device. screen.
• Adjust the volume to levels that allow • When cleaning the device, make sure
the driver to hear sounds from outside to turn off the device and use a dry
of the vehicle. Driving in a state where and smooth cloth. Never use tough
external sounds cannot be heard may materials, chemical cloths, or solvents
lead to accidents. (alcohol, benzene, thinners, etc.) as
• Pay attention to the volume setting such materials may damage the device
when turning the device on. A sudden panel or cause color/quality deteriora-
tion.
output of extreme volume upon turn-
• Do not place beverages close to the ✽ NOTICE
ing the device on could lead to hearing
impairment. (Adjust the volume to a audio system. Spilling beverages may File formats that do not comply with the
suitable levels before turning off the lead to system malfunction. above formats may not be properly rec-
device.) • In case of product malfunction, please ognized or play without properly dis-
• If you want to change the position of contact your place of purchase or playing file names or other information.
device installation, please inquire with After Service center.
your place of purchase or service • Placing the audio system within an
maintenance center. Technical expert- electromagnetic environment may
ise is required to install or disassemble result in noise interference.
the device.
• Turn on the car ignition before using
this device. Do not operate the audio
system for long periods of time with
the ignition turned off as such opera-
tions may lead to battery discharge.
(Continued)
4 12
Multimedia System
Support for Compressed Files • For MP3/WMA compression files, dif- Language Support (Unicode Support)
1. Supported Bitrates (Kbps) ferences in sound quality will occur • Korean: 2,604 characters
depending on the bitrate. (Higher • English: 94 characters
sound quality can be experienced with • Common Chinese characters: 4,888
higher bitrates.) characters
• This device only recognizes files with • Special symbols: 986 characters
MP3/WMA extensions. Other file
extensions may not be properly recog-
nized. ✽ NOTICE
Japanese/Simplified Chinese characters
3. Maximum number of recognized fold- are not supported.
ers and files
• Folder: 1,000 folders for USB
• File: 5,000 files for USB
• There are no limitations to the number of
recognized folder levels.
4. Text Display (Based on Unicode)

• File name: Maximum 40 English char-
acters
• Folder name: Max 40 English charac-
ters
✽ NOTICE
2. Sampling Frequencies (Hz) Using the scroll feature allows you to see
the entire name of files with names that
are too long to be displayed at once.
4 13
Multimedia System
✽ NOTICE - Using the USB (Continued) (Continued)

Device • When the formatted byte/sector set- • Do not use the USB device for purpos-
• To use an external USB device, make ting of External USB device is not es other than playing music files.
sure the device is not connected when either 512BYTE or 2048BYTE, then • Playing videos through the USB is not
starting up the vehicle. Connect the the device will not be recognized. supported.
device after starting up. • Use only a USB device formatted to • Use of USB accessories such as
• If you start the engine when the USB FAT 12/16/32. rechargers or heaters using USB I/F
device is connected, it may damage • USB devices without USB I/F authenti- may lower performance or cause trou-
the USB device. (USB flashdrives are cation may not be recognizable. ble.
very sensitive to electric shock.) • Make sure the USB connection termi- • If you use devices such as a USB hub
• If the engine is started up or turned nal does not come in contact with the purchased separately, the vehicle’s
off while the external USB device is human body or other objects. audio system may not recognize the
connected, the external USB device • If you repeatedly connect or discon- USB device. In that case, connect the
may not work. nect the USB device in a short period USB device directly to the multimedia
• The System may not play inauthentic of time, it may break the device. terminal of the vehicle.
MP3 or WMA files. • You may hear a strange noise when • If the USB device is divided by logical
1) It can only play MP3 files with the connecting or disconnecting a USB drives, only the music files on the
compression rate between 8Kbps ~ device. highest-priority drive are recognized
320Kbps. • If you disconnect the external USB by car audio.
2) It can only play WMA music files device during playback in USB mode, • Devices such as MP3 Player/ Cellular
with the compression rate between the external USB device can be dam- phone/Digital camera can be unrecog-
8Kbps ~ 320Kbps. aged or may malfunction. Therefore, nizable by standard USB I/F can be
• Take precautions for static electricity disconnect the external USB device unrecognizable.
when connecting or disconnecting the when the audio is turned off or in • Charging through the USB may not
external USB device. another mode. (e.g, Radio, CD) be supported in some mobile devices.
• An encrypted MP3 PLAYER is not • Depending on the type and capacity of • USB HDD or USB types liable to con-
recognizable. the external USB device or the type of nection failures due to vehicle vibra-
• Depending on the condition of the the files stored in the device, there is a tions are not supported. (i-stick type)
external USB device, the connected difference in the time taken for recog- (Continued)
external USB device can be unrecog- nition of the device.
nizable. (Continued)
(Continued)
4 14
Multimedia System
(Continued) ✽ NOTICE - Using the iPod® occur depending on the characteristics

• Some non-standard USB devices Device of your iPod®/iPhone® device.
(METAL COVER TYPE USB) can be • If your iPhone® is connected to both the
unrecognizable. • iPod® is a registered trademark of Bluetooth® Wireless Technology and
• Some USB flash memory readers Apple Inc. USB, the sound may not be properly
(such as CF, SD, micro SD, etc.) or • Some iPod® models may not support played. In your iPhone®, select the
external-HDD type devices can be communication protocol and files may Dock connector or Bluetooth® Wireless
unrecognizable. not properly play. Technology to change the sound output
• Music files protected by DRM (DIGI- Supported iPod® models: (source).
TAL RIGHTS MANAGEMENT) are - iPhone® 3GS/4 • When connecting iPod® with the iPod®
not recognizable. - iPod® touch 1st~4th generation Power Cable, insert the connector to
• The data in the USB memory may be - iPod® nano 1st~6th generation the multimedia socket completely. If
lost while using this audio. Always - iPod® classic not inserted completely, communica-
back up important data on a personal • The order of search or playback of tions between iPod® and audio may be
storage device. songs in the iPod® can be different interrupted.
• Please avoid using USB from the order searched in the audio • When adjusting the sound effects of the
memory products which system. iPod® and the audio system, the sound
can be used as key chains • If the iPod® disabled due to its own effects of both devices will overlap and
or cellular phone acces- malfunction, reset the iPod®. (Reset: might reduce or distort the quality of
sories as they could cause Refer to iPod® manual) the sound.
damage to the USB jack. Please make • An iPod® may not operate normally • Deactivate (turn off) the equalizer func-
certain only to use plug type connec- on low battery. tion of an iPod® when adjusting the
tor products. • Some iPod® devices, such as the iPhone®, audio system’s volume, and turn off the
can be connected through the Bluetooth® equalizer of the audio system when
Wireless Technology interface. The using the equalizer of an iPod®.
device must have audio Bluetooth® • When not using iPod® with car audio,
Wireless Technology capability (such as detach the iPod® cable from iPod®.
for stereo headphone Bluetooth® Wireless Otherwise, iPod® may remain in acces-
Technology ). The device can play, but it sory mode, and may not work properly.
will not be controlled by the audio system. • Beside support 1M cable when pur-
• To use iPod® features within the chasing iPod®/iPhone® products, Long
audio, use the cable provided upon Cable cannot be recognized.
purchasing an iPod® device.
• Skipping or improper operation may
4 15
Multimedia System
Media Mode Shuffle: [2 SHFL] button Search Song: TUNE knob

Change Mode: [MEDIA] button • Plays all songs within the current fold- • Turning TUNE knob: Searches for
• Each time the button is pressed, er(category) or play all songs in ran- songs(files).
the media mode popup will be dis- dom order. • Pressing TUNE knob: Plays selected
played or closed. • Audio CD, iPod® mode: Shuffle All ➟ song(file).
• The media mode popup will not be Shuffle Off
displayed when [SETUP] button • MP3 CD, USB mode: Shuffle Folder ➟ ✽ NOTICE
[Display] [Mode popup] is turned Shuffle All ➟ Off AUX don’t support playlist feature.
[Off].
You can select a menu in the mode popup Change Song/File: [SEEK/TRACK] but- Search Folder: [FOLDER] button
by using the preset [1] ~ [6] buttons or ton • Searches the previous/next folder.
TUNE knob. ∨ SEEK/TRACK]
[∨ (MP3 CD, USB)
• If media device(CD, USB, AUX) is con- • Pressing the button: Plays the current • If a folder is selected by pressing the
nected, then it will automatically oper- song from the beginning. If the [∨ ∨ TUNE knob, the first file within the
ate. Once it is disconnected, the previ- SEEK/TRACK] button is pressed again selected folder will be played.
ous mode will be restored. within 3 seconds, the previous song is
• The Audio/AUX volume can also be played.
controlled. • Pressing and holding the button:
Rewinds the song.
Repeat: [1 RPT] button [SEEK/TRACK ∧]
• Repeats the current song or repeats all • Pressing the button: Plays the next
songs within the current folder. song.
• Audio CD, iPod® mode: Repeat Song • Pressing and holding the button: Fast-
➟ Repeat Off forwards the song.
• MP3 CD, USB mode: Repeat Song ➟ • AUX don’t support Rewind/Fast-for-
Repeat Folder ➟ Off ward feature.
4 16
Multimedia System
Disc(Audio CD) Information Repeat

Displays information of the current song. Repeats the current song. Press it again
to turn off.
Sound Settings
Moves to Sound Settings. Repeat Folder
Repeats songs within the current folder.
Disc(MP3 CD)/USB Press it again to turn off.
Shuffle Folder
Displays Menu Popup when pressing the Randomly plays songs within the current
[MENU] button. folder. Press it again to turn off.
List Shuffle
Moves to the list screen. Randomly plays all songs. Press it again
to turn off.
Repeat
Repeats the current song. Press it again Scan
to turn off. Scans the beginning parts of all songs.
(approximately 10 seconds per file)
Shuffle
Randomly plays all songs. Press it again Information
to turn off. Displays information of the current song.
Displays Menu Popup when pressing the
Scan [MENU] button.
Sound Settings
Scans the beginning parts of all songs. Moves to Sound Settings.
(approximately 10 seconds per file) List
Moves to the list screen.
4 17
Multimedia System
iPod® AUX
Displays Menu Popup when pressing the Displays Menu Popup when pressing the
[MENU] button. [MENU] button.
List Sound Settings

Moves to the list screen. Moves to Sound Settings.
Repeat ✽ NOTICE
Repeats the current song. Press it again • AUX mode can be used only when an
to turn off. external audio player has been con-
nected.
Shuffle • If only a cable is connected to the AUX
Plays all songs within the currently play- without an external device, the mode
ing category in random order. Press it will be changed to AUX, but noise
again to turn off. may occur. When an external device is
not being used, remove the connector
Information jack.
• When the external device power is
Displays information of the current song. connected to the power jack, playing
the external device may output noise.
Sound Settings In such cases, disconnect the power
Moves to Sound Settings. connection before use.
4 18
Multimedia System
Setup Language
Press the [SETUP] button Select
Display [Language].
Press the [SETUP] button Select • Changes the display language.
[Display].
• Media Display: When playing an MP3 Display Off
file, select the desired display info from Press the [SETUP] button Select
[Folder/File] or [Artist/Title/Album]. [Display Off].
• Mode Popup: During [On] state, press • Audio operation is maintained and only
the [FM] or [MEDIA] button to display the screen will be turned Off. In the
the mode change popup. Screen Off state, press any button to
• Text Scroll: If MP3 file name is too long turn the Screen On again.
to display, the file name is scrolled from
right to left.
Sound
Press the [SETUP] button Select
[Sound].
• Balance: Selects the sound balance.
• Tone: Selects the sound tone.
• Speed Dependent Vol.: Controls the
volume level automatically according
to the speed of the vehicle.
4 19
Before starting the engine / 5-3
Key positions / 5-4
Manual transmission / 5-8
Cruise control system / 5-16
Locking differential / 5-21
Driving for economy / 5-22
Special driving conditions / 5-23
Winter driving / 5-25
Higher speed motoring / 5-26
Trailer or vehicle towing / 5-27
Driving your vehicle 5

Driving your vehicle
WARNING - ENGINE EXHAUST CAN BE DANGEROUS!

Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the win-
dows immediately.
• Do not inhale exhaust fumes.

Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyxia-
tion.
• Be sure the exhaust system does not leak.
The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If you hear
a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the car, we recom-
mend that the system be checked by an authorized HYUNDAI dealer.
• Do not run the engine in an enclosed area.
Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine in your
garage any longer than it takes to start the engine and back the car out.
• Avoid idling the engine for prolonged periods with people inside the car.
If it is necessary to idle the engine for a prolonged period with people inside the car, be sure to do so only in an open area
with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interior.
To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the windshield are
kept clear of snow, ice, leaves or other obstructions.
5 2
BEFORE STARTING THE ENGINE

Before you start the engine, you
should always: WARNING WARNING
1. Look around the vehicle to be sure To ensure that sufficient vacuum Driving while distracted can result
there are no flat tires, puddles of oil, exists within the brake system dur- in a loss of vehicle control, that
water or other indications of possible ing cold weather start-up condi- may lead to an accident, severe
trouble. tions, it is necessary to run the personal injury, and death. The dri-
2. After entering the car, check to be engine at idle for several seconds ver’s primary responsibility is in
sure the parking brake is engaged. after starting the engine. the safe and legal operation of a
vehicle, and use of any handheld
3. Check that all windows, and lights are
devices, other equipment, or vehi-
clean.
cle systems which take the driver’s
4. Check that the interior and exterior
mirrors are clean and in position.
WARNING eyes, attention and focus away
• Always wear appropriate shoes from the safe operation of a vehicle
5. Check your seat, seatback and head- or which are not permissible by law
when operating your vehicle.
rest to be sure they are in their proper should never be used during oper-
Unsuitable shoes (high heels, ski
positions. ation of the vehicle.
boots,etc.) may interfere with
6. Lock all the doors. your ability to use the brake and
7. Fasten your seat belt and be sure that accelerator pedal, and the clutch
all other occupants have fastened (if equipped).
theirs. • Do not start the vehicle with the
8. Turn off all lights and accessories that accelerator pedal depressed. The
are not needed. vehicle can move and lead to an
9. When you turn the ignition switch to accident.
"ON", check that all appropriate warn- • Wait until the engine rpm is nor-
ing lights are operating and that you mal. The vehicle may suddenly
have sufficient fuel. move if the brake padel is
10.Check the operation of warning lights released when the rpm is high.
and all bulbs when key is in the "ON"
position.
5 3
KEY POSITIONS
To start the engine
WARNING Combination ignition Switch WARNING
• When you intend to park or stop • Place the shift lever in neutral and The engine should not be turned off
the vehicle with the engine on, be depress the clutch pedal fully. or the key removed from the igni-
careful not to depress the accel- • To start the engine, insert the ignition tion key cylinder while the vehicle
erator pedal for a long period of key and turn it to the "START" position. is in motion. The steering wheel is
time. It may overheat the engine Release it as soon as the engine locked by removing the key.
or exhaust system and cause fire. starts. Do not hold the key in the
• When you make a sudden stop or "START" position for more than 15 sec-
turn the steering wheel rapidly, onds.
loose objects may drop on the ACC
floor and it could interfere with LOCK ON
the operation of the foot pedals,
possibly causing an accident.
Keep all things in the vehicle
safely stored.
• If you do not focus on driving, it
may cause an accident. Be care-
START
ful when operating what may dis-
turb driving such as audio or
heater. It is the responsibility of
the driver to always drive safely. C040A01E-1
• "START"
The engine is started in this position. It
will crank until you release the key.
✽ NOTICE
Do not hold the key in the "START"
position for more than 15 seconds.
5 4
• "ON"
ACC
When the key is in the "ON" position, the
ignition is on and all accessories may be LOCK ON
turned on. If the engine is not running,
the key should not be left in the "ON"
position. This will discharge the battery
and may also damage the ignition sys-
tem.
START
• "ACC"
With the key in the "ACC" position, some
electrical accessories (radio etc.) may be C070C01E-1 C050A01E-1
operated.
To remove the ignition key Starting
1. Turn the ignition key to the "ACC"
• "LOCK" position.
The key can be removed or inserted in 2. Simultaneously push and turn the
WARNING
this position. ignition key counterclockwise from the Never run the engine in a closed or
To protect against theft, the steering "ACC" position to the "LOCK" posi- poorly ventilated area any longer
wheel locks by removing the key. tion. than is needed to move your car in
or out of the area. The carbon
3. The key can be removed in the
monoxide gas emitted is odorless
✽ NOTICE "LOCK" position.
and can cause serious injury or
If difficulty is experienced turning the death.
ignition key to the ACC position, turn
the key while turning steering wheel
right and left to release the tension.
CAUTION
Do not turn the ignition switch to
the START position with the engine
running. It may damage the starter.
5 5
Starting for the diesel engine Normal conditions

ENGINE COLD The Starting Procedure:
• Turn the ignition key to position "ON" 1. Insert key, and fasten the seat belt.
and wait for the pre-heat indicator light 2. Depress the clutch pedal fully and Amber lamp ON Amber lamp OFF
to go out. place the gearshift lever in neutral.
• Operate the starter until the engine 3. After turning the ignition key to the
runs. "ON" position, make certain all warn-
ing lights and gauges are functioning
ENGINE WARM properly before starting the engine.
Operate the starter. If the engine does 4. On vehicles equipped with the diesel
not respond on the first attempt, wait sev- preheat indicator light, turn the ignition
eral seconds and try again using the pre- key to the "ON" position. The diesel C050B01HP
heat. pre-heat indicator light will first illumi-
nate in amber, and then after a short ✽ NOTICE
time, the amber illumination will go off, If the engine were not started within 10
indicating that preheating is completed. seconds after the preheating is complet-
ed, turn the ignition key once more to
the "LOCK" position, and then to the
"ON" position, in order to preheat
again.
5 6
Starting and stopping the engine

WARNING for turbo charger intercooler
Be sure that the clutch is fully (1)Do not race or accelerate the engine
depressed when starting a manual immediately after starting. If the
transmission vehicle. Otherwise engine is cold, idle for several second
there is the potential to cause dam- before sufficient lubrication is ensured
age to the vehicle or injury to some- in the turbocharger unit.
one inside or outside the vehicle as (2)After high speed or extended driving,
a result of the forward or backward requiring a heavy engine load, run the
movement of the vehicle that will engine on idle condition about 1
occur if the clutch is not depressed minute before turning it off. This idle
when the vehicle is started. time will allow the turbocharger to cool
prior to shutting the engine off.
5. Turn the ignition key to the "START"
position and release it when the
engine starts. WARNING
Do not turn the engine off immedi-
ately after it has been subjected to
a heavy load. Doing so may cause
severe damage to the engine or
turbo charger unit.
5 7
MANUAL TRANSMISSION
■ Type A Your HYUNDAI's manual transmission
has a conventional shift pattern. This shift CAUTION
pattern is imprinted on the shift knob. The • When downshifting from fifth
transmission is fully synchronized in all gear to fourth gear, caution
forward gears so shifting to either a high- should be taken not to inadver-
er or a lower gear is easily accomplished. tently press the gear lever side-
ways in such a manner that sec-
✽ NOTICE ond gear is engaged. Such a dras-
• To shift into reverse, rest the lever in tic downshift may cause the
neutral for at least 3 seconds after engine speed to increase to the
your car is completely stopped. Then point that the tachometer will
move the lever into the reverse posi- enter the red-zone. Such over-
tion. revving of the engine may possi-
■ Type B • During cold weather, shifting may be bly cause engine damage.
difficult until the transmission lubri- • Do not downshift more than 2
cant has warmed up. This is normal gears or downshift the gear when
and not harmful to the transmission. the engine is running at high
• If you've come to a complete stop and speed (5,000 RPM or higher).
it's hard to shift into 1st or R Such a downshifting may damage
(Reverse), put the shift lever in N the engine, clutch and the trans-
(Neutral) position and release the mission.
clutch. Press the clutch pedal back • When shifting into 5th or 6th gear,
down, and then shift into 1st or R press the shift lever to the right.
(Reverse) gear position. Otherwise, the engine could be
• Do not use the shift lever as a handrest damaged by accidentally engag-
during driving, as this can result in ing 3rd or 4th gear.
The shift lever can be moved without premature wear of the transmission
pulling the ring (1). shift
The ring (1) must be pulled up while
moving the shift lever.
HHR3026/OLM059009
5 8
Using the Clutch Good Driving Practices

WARNING The clutch should be pressed all the way • Never take the car out of gear and
• If your vehicle has a manual to the floor before shifting, then released coast down a hill. This is extremely
transmission not equipped with a slowly. If your vehicle is equipped with an hazardous. Always leave the car in
ignition lock switch, it may move ignition lock switch, the engine will not gear.
and cause a serious accident start when starting the engine without • Don't "ride" the brakes. This can cause
when starting the engine without depressing the clutch pedal. (if equipped) them to overheat and malfunction.
depressing the clutch pedal while The clutch pedal should always be used Instead, when you are driving down a
the parking brake is released and after fully returning to the original posi- long hill, slow down and shift to a lower
the shift lever not in the N tion. Do not rest your foot on the clutch gear. When you do this, engine braking
(Neutral) position. pedal while driving. This can cause will help slow the car.
• Do not use the engine brake unnecessary wear. Do not partially • Slow down before shifting to a lower
(shifting from a high gear to engage the clutch to hold the car on an gear. This will help avoid over-revving
lower gear) rapidly on slippery incline. This causes unnecessary wear. the engine, which can cause damage.
roads. The vehicle may slip caus- Use the parking brake to hold the car on • Slow down when you encounter cross
ing an accident. an incline. Do not operate the clutch winds. This gives you much better con-
pedal rapidly and repeatedly. trol of your car.
• Be sure the car is completely stopped
CAUTION before you attempt to shift into reverse.
The transmission can be damaged if
To prevent possible damage to the you do not. To shift into reverse,
clutch system, do not start with the depress the clutch, move the shift lever
2nd (second) gear engaged except to neutral, wait three seconds, then
when you start on a slippery road. shift to the reverse position.
• Exercise extreme caution when driving
on a slippery surface. Be especially
careful when braking, accelerating or
shifting gears. On a slippery surface,
an abrupt change in vehicle speed can
cause the drive wheels to lose traction
and the vehicle to go out of control.
5 9
Anti-lock brake system (ABS) The ABS continuously senses the speed
WARNING (if equipped) of the wheels. If the wheels are going to
• Avoid high cornering speeds. lock, the ABS system repeatedly modu-
• Do not make quick steering lates the hydraulic brake pressure to the
WARNING wheels.
wheel movements, such as sharp
ABS will not prevent accidents due When you apply your brakes under con-
lane changes or fast, sharp turns.
to improper or dangerous driving ditions which may lock the wheels, you
• Always wear your seat belts. In a maneuvers. Even though vehicle
collision crash, an unbelted per- may hear a “tik-tik’’ sound from the
control is improved during emer- brakes, or feel a corresponding sensation
son is significantly more likely to gency braking, always maintain a
die than a person wearing a seat- in the brake pedal. This is normal and it
safe distance between you and means your ABS is active.
belt. objects ahead. Vehicle speeds
• The risk of rollover is greatly In order to obtain the maximum benefit
should always be reduced during from your ABS in an emergency situa-
increased if you lose control of extreme road conditions.
your vehicle at highway speeds. tion, do not attempt to modulate your
The braking distance for vehicles brake pressure and do not try to pump
• Loss of control often occurs if equipped with an anti-lock braking your brakes.
two or more wheels drop off the system may be longer than for those
roadway and the driver over- Press your brake pedal as hard as possi-
without it in the following road con- ble or as hard as the situation allows the
steers to reenter the roadway. ditions. ABS to control the force being delivered
• In the event your vehicle leaves During these conditions the vehicle to the brakes.
the roadway, do not steer sharply. should be driven at reduced speeds:
Instead, slow down before pulling • Rough, gravel or snow-covered
back into the travel lanes. roads.
✽ NOTICE
• Never exceed posted speed lim- A click sound may be heard in the
• With tire chains installed.
its. engine compartment when the vehicle
• On roads where the road surface begins to move after the engine is start-
is pitted or has different surface ed. These conditions are normal and
height. indicate that the anti-lock brake system
The safety features of an ABS is functioning properly.
equipped vehicle should not be test-
ed by high speed driving or corner-
ing. This could endanger the safety
of yourself or others.
5 10
• Even with the anti-lock brake system,

your vehicle still requires sufficient CAUTION
stopping distance. Always maintain a • When you drive on a road having
safe distance from the vehicle in front poor traction, such as an icy road,
of you. and operate your brakes continu-
• Always slow down when cornering. ously, the ABS will be active con-
The anti-lock brake system cannot pre- tinuously and the ABS warning
vent accidents resulting from exces- light may illuminate. Pull your
sive speeds. vehicle over to a safe place and
• On loose or uneven road surfaces, stop the engine.
operation of the anti-lock brake system • Restart the engine. If the ABS
may result in a longer stopping dis- warning light is off, then your
tance than for vehicles equipped with a W-78 ABS system is normal.
conventional brake system. Otherwise, you may have a prob-
CAUTION lem with the ABS. We recommend
• If the ABS warning light is on and that you contact an authorized
stays on, you may have a problem HYUNDAI dealer.
with the ABS. In this case, howev-
er, your regular brakes will work
normally. ✽ NOTICE
• The ABS warning light will stay When you jump start your vehicle
on for approximately 3 seconds because of a drained battery, the engine
after the ignition switch is ON. may not run as smoothly and the ABS
During that time, the ABS will go warning light may turn on at the same
through self-diagnosis and the time. This happens because of the low
light will go off if everything is battery voltage. It does not mean your
normal. If the light stays on, you ABS is malfunctioning.
may have a problem with your • Do not pump your brakes!
ABS. We recommend that you • Have the battery recharged before
contact an authorized HYUNDAI driving the vehicle.
dealer.
5 11
The Electronic Stability Control (ESC)

WARNING system is an electronic system designed
Never drive too fast according to to help the driver maintain vehicle control
the road conditions or too quickly under adverse conditions. It is not a sub-
when cornering. Electronic Stability stitute for safe driving practices. Factors
Control (ESC) will not prevent acci- including speed, road conditions and
dents. Excessive speed in turns, driver steering input can all affect
abrupt maneuvers and hydroplan- whether ESC will be effective in prevent-
ing on wet surfaces can still result ing a loss of control. It is still your respon-
in serious accidents. Only a safe sibility to drive and corner at reasonable
and attentive driver can prevent speeds and to leave a sufficient margin
accidents by avoiding maneuvers of safety.
OHR047171L that cause the vehicle to lose trac- When you apply your brakes under con-
Electronic stability control (ESC) tion. Even with ESC installed, ditions which may lock the wheels, you
always follow all the normal pre- may hear a “tik-tik’’ sound from the
(If equipped) brakes, or feel a corresponding sensation
cautions for driving - including
The Electronic Stability Control (ESC) driving at safe speeds for the con- in the brake pedal. This is normal and it
system is designed to stabilize the vehi- ditions. means your ESC is active.
cle during cornering maneuvers. ESC
checks where you are steering and
where the vehicle is actually going. ESC
applies the brakes on individual wheels ✽ NOTICE
and intervenes with the engine manage- A click sound may be heard in the
ment system to stabilize the vehicle. engine compartment when the vehicle
begins to move after the engine is start-
ed. These conditions are normal and
indicate that the Electronic Stability
Control System is functioning properly.
5 12
ESC operation When operating Indicator light

ESC ON condition When the ESC is in operation, When ignition switch is turned
• When the ignition is turned the ESC indicator light blinks. to the ON position, the indica-
ON, ESC and ESC OFF indi- • When the Electronic Stability tor light illuminates, then goes
- Control is operating properly, off if the ESC system is operat-
cator lights illuminate for
approximately 3 seconds, you can feel a slight pulsa- ing normally.
then ESC is turned on. tion in the vehicle. This is The ESC indicator light blinks
• Press the ESC OFF button only the effect of brake con- whenever ESC is operating or
for at least half a second trol and indicates nothing illuminates when ESC fails to
after turning the ignition ON unusual. operate.
to turn ESC off. (ESC OFF • When moving out of the mud ESC OFF indicator light comes
indicator will illuminate). To or slippery road, pressing the on when the ESC is turned off
turn the ESC on, press the accelerator pedal may not with the button.
ESP OFF button (ESC OFF cause the engine rpm (revolu-
indicator light will go off). tions per minute) to increase. CAUTION
• When starting the engine, Driving with varying tire or wheel
you may hear a slight ticking ESC operation off sizes may cause the ESC system to
sound. This is the ESC per- ESC OFF condition malfunction. When replacing tires,
forming an automatic system To cancel ESC operation : make sure they are the same size as
self-check and does not indi- your original tires.
cate a problem. • To cancel ESC operation,
press the ESC OFF button
(ESC OFF indicator light illu-
minates). WARNING
• If the ignition switch is turned The Electronic Stability Control
to LOCK position when ESC system is only a driving aid; use
is off, ESC remains off. precautions for safe driving by
Upon restarting the engine, slowing down on curved, snowy, or
the ESC will automatically icy roads. Drive slowly and don’t
turn on again. attempt to accelerate whenever the
ESC indicator light is blinking, or
when the road surface is slippery.
5 13
ESC OFF usage Hill-start assist control (HAC) Good braking practices
When driving (if equipped)
• ESC should be turned on for daily driv- A vehicle has the tendency to slip back WARNING
ing whenever possible. on a steep hill when it starts to go after Objects should not extend higher
• To turn ESC off while driving, press the stopping. The Hill-start Assist Control than the top of the front seatbacks.
ESC OFF button while driving on a flat (HAC) prevents the vehicle from slipping If there were an accident or a sud-
road surface. back by operating the brakes automati- den stop, such objects could move
cally for about 2 seconds. The brakes are forward and cause damage to the
released when the accelerator pedal is vehicle or injure the occupants.
WARNING depressed or after about 2 seconds.
Never press the ESC OFF button
while ESC is operating (ESC indica- • After being parked, check to be sure
tor light blinks). WARNING the parking brake is not engaged and
If ESC is turned off while ESC is The HAC is activated only for about that the parking brake indicator light is
operating, the vehicle may slip out 2 seconds, so when the vehicle is out before driving away.
of control. starting off always depress the • Driving through water may get the
accelerator pedal. brakes wet. They can also get wet
when the car is washed. Wet brakes
✽ NOTICE ✽ NOTICE
can be dangerous! Your car will not
• When operating the vehicle on a stop as quickly if the brakes are wet.
• The HAC does not operate when the Wet brakes may cause the car to pull
dynamometer, ensure that the ESC is transaxle shift lever is in the P (Park)
turned off (ESC OFF light illuminat- to one side. To dry the brakes, apply
or N (Neutral) position. the brakes lightly until the braking
ed). If the ESC is left on, it may pre- • The HAC activates even though the
vent the vehicle speed from increas- action returns to normal, taking care to
ESC is off but it does not activate keep the car under control at all times.
ing, and result in false diagnosis. when the ESC has malfunctioned.
• Turning the ESC off does not affect If the braking action does not return to
ABS or brake system operation. normal, stop as soon as it is safe to do
so and call your HYUNDAI dealer for
assistance.
5 14
• Don't coast down hills with the car out • Under some conditions your parking
of gear. This is extremely hazardous. brake can freeze in the engaged posi- WARNING
Keep the car in gear at all times, use tion. This is most likely to happen when Always, confirm the position of the
the brakes to slow down, then shift to a there is an accumulation of snow or ice brake and accelerator pedal before
lower gear so that engine braking will around or near the rear brakes or if the driving. If you don’t check the posi-
help you maintain a safe speed. brakes are wet. If there is a risk that the tion of the accelerator and brake
• Don't "ride" the brake pedal. Resting parking brake may freeze, apply it only pedal before driving, you may
your foot on the brake pedal while driv- temporarily while you put the gear depress the accelerator instead of
ing can be dangerous because it can selector lever in first or reverse gear the brake pedal. It may cause a seri-
result in the brakes overheating and and block the rear wheels so the car ous accident.
losing their effectiveness. It also cannot roll. Then release the parking
increases the wear of the brake com- brake.
ponents. • Do not hold the vehicle on the upgrade
• If a tire goes flat while you are driving, with the accelerator pedal. This can CAUTION
apply the brakes gently and keep the cause the transmission to overheat. Do not operate the parking brake
car pointed straight ahead while you Always use the brake pedal or parking while the vehicle is moving except
slow down. When you are moving brake. in an emergency situation. It could
slowly enough for it to be safe to do so, damage the vehicle system and
pull off the road and stop in a safe make endanger driving safety.
place.
• Use caution when parking on a hill.
Engage the parking brake and place
the gear selector lever in first or
reverse gear. If your car is facing down-
hill, turn the front wheels into the curb
to help keep the car from rolling. If your
car is facing uphill, turn the front
wheels away from the curb to help
keep the car from rolling.
If there is no curb or if it is required by
other conditions to keep the car from
rolling, block the wheels.
5 15
CRUISE CONTROL SYSTEM (IF EQUIPPED)

(Continued)
WARNING
• Pay particular attention to the
• If the cruise control is left on,
driving conditions whenever
(CRUISE indicator light in the
using the cruise control system.
instrument cluster illuminated)
the cruise control can be activat- • Be careful when driving downhill
ed unintentionally. Keep the using the cruise control system,
cruise control system off which may increase the vehicle
(CRUISE indicator light OFF) speed.
when the cruise control is not in
use, to avoid inadvertently set-
ting a speed. CAUTION
OHR047226 • Use the cruise control system During cruise-speed driving with a
only when traveling on open
➀ CRUISE indicator highways in good weather.
manual transmission vehicle, do
➁ SET indicator not shift into neutral without
• Do not use the Cruise Control depressing the clutch pedal, since
when it may be unsafe to keep the engine will be overrevved. If this
The cruise control system allows you to the vehicle at a constant speed: happens, depress the clutch pedal
program the vehicle to maintain a con- - When driving in heavy traffic or or release the CRUISE switch.
stant speed without resting your foot on when traffic conditions make it
the accelerator pedal. difficult to drive at a constant
This system is designed to function speed
above approximately 30 km/h (19 mph). - When driving on rainy, icy, or
snow-covered roads
- When driving on hilly or windy
roads
- When driving in windy areas
- When driving with limited view
(possibly due to bad weather
such as fog, snow, rain and
sandstorm)
(Continued)
5 16
✽ NOTICE
• During normal cruise control opera-
tion, when the SET switch is activated
or reactivated after applying the
brakes, the cruise control will ener-
gize after approximately 3 seconds.
This delay is normal.
• To activate cruise control, depress the
brake pedal at least once after turning
the ignition switch to the ON position
or starting the engine. This is to check
if the brake switch which is important
part to cancel cruise control is in nor- OHR057134 OHR057135
mal condition. Cruise control switch To set cruise control speed:
CRUISE : Turns cruise control system on 1. Push the CRUISE button on the steer-
or off. ing wheel to turn the system on. The
CANCEL: Cancels cruise control opera- CRUISE indicator light in the instru-
tion. ment cluster will illuminate.
RES+: Resumes or increases cruise 2. Accelerate to the desired speed, which
control speed. must be more than 30 km/h (19 mph).
SET-: Sets or decreases cruise control
speed. ✽ NOTICE - Manual
transmission
For manual transmission vehicles, you
should depress the brake pedal at least
once to set the cruise control after start-
ing the engine.
5 17
OHR057136 OHR057137 OHR057136

3. Move the toggle switch down (to SET-), To increase cruise control set To decrease the cruising speed:
and release it at the desired speed. speed: Follow either of these procedures:
The SET indicator light in the instru- Follow either of these procedures: • Move the toggle switch down (to SET-)
ment cluster will illuminate. Release
• Move the toggle switch up (to RES+) and hold it. Your vehicle will gradually
the accelerator at the same time. The
and hold it. Your vehicle will accelerate. slow down. Release the toggle switch
desired speed will automatically be
Release the toggle switch at the speed at the speed you want to maintain.
maintained.
you want. • Move the toggle switch down (to SET-)
On a steep grade, the vehicle may slow
• Move the toggle switch up (to RES+) and release it immediately. The cruis-
down or speed up slightly while going
and release it immediately. The cruising ing speed will decrease by 2.0 km/h or
uphill or downhill.
speed will increase by 2.0 km/h or 1 mph 1 mph each time the toggle switch is
each time the toggle switch is operated operated in this manner.
in this manner.
5 18
To temporarily accelerate with the Each of these actions will cancel cruise
cruise control on: control operation (the SET indicator light
If you want to speed up temporarily when in the instrument cluster will go off), but it
the cruise control is on, depress the will not turn the system off. If you wish to
accelerator pedal. Increased speed will resume cruise control operation, move
not interfere with cruise control operation the toggle switch up (to RES+). You will
or change the set speed. return to your previously preset speed.
To return to the set speed, take your foot
off the accelerator.
OHR057138
To cancel cruise control, do one
of the following:
• Depress the brake pedal.
• Depress the clutch pedal with a manu-
al transmission.
• Shift into N (Neutral) with an automatic
transmission.
• Press the CANCEL switch located on
the steering wheel.
• Decrease the vehicle speed lower than
the memory speed by 20 km/h (12 mph).
• Decrease the vehicle speed to less
than approximately 30 km/h (19 mph).
5 19
To turn cruise control off, do one

of the following:
• Push the CRUISE button (the CRUISE
indicator light in the instrument cluster
will go off).
• Turn the ignition off.
Both of these actions cancel cruise con-
trol operation. If you want to resume
cruise control operation, repeat the steps
provided in "To set cruise control speed"
on the previous page.
OHR057137
To resume cruising speed at
more than approximately 30 km/h
(19 mph):
If any method other than the CRUISE
switch was used to cancel cruising speed
and the system is still activated, the most
recent set speed will automatically
resume when you move the toggle switch
up (to RES+).
It will not resume, however, if the vehicle
speed has dropped below approximately
30 km/h (19 mph).
✽ NOTICE
Always check the road conditions when
you move the toggle switch up (to RES+)
to resume the speed.
5 20
LOCKING DIFFERENTIAL (IF EQUIPPED)

A locking differential, if equipped, is for The following procedures can be used to
the rear wheel differential only. The fea- confirm that the locking differential is CAUTION
tures of this locking differential are functioning properly: • Never start the engine with the
described below: gearshift lever placed in the for-
Just as with a conventional differential, (1)Position the vehicle so that one wheel ward or reverse while one of the
the wheel on one side is allowed to turn is on a dry paved surface and the rear wheels is jacked up and the
at a different speed from the wheel on other on ice, snow, mud, etc. other in contact with the ground;
the other side when the vehicle is corner- Drive the vehicle, and observe the doing so may cause the vehicle to
ing. The difference between the locking operation of the locking differential. jump forward.
differential and a conventional differential The vehicle should not become stuck if • If one of the rear wheels begins to
is that if the wheel on one side of the the differential is functioning properly. spin in mud, snow, etc., the vehi-
vehicle loses traction, a greater amount cle can sometimes be driven out
of torque is applied to the rear wheel on (2)Depress the accelerator pedal gradu-
by depressing the accelerator
the other side to improve traction. ally, and then when traction is good,
pedal further; however, avoid run-
depress it forcefully. If the vehicle
ning the engine continuously at
accelerates well, the differential is
✽ NOTICE functioning properly.
high rpm because doing so could
In a stationary position, the LD damage the locking differential.
(Locking Differential) will operate when
the difference of the revolution speed
between the rear right wheel and the
rear left wheel occurs.
5 21
DRIVING FOR ECONOMY

You can save fuel and get more kilome- • Take care of your tires. Keep them • Travel lightly. Don't carry unnecessary
ters from your car if you follow these sug- inflated to the recommended pressure. weight in your car. Weight reduces fuel
gestions: Incorrect inflation, either too much or economy.
too little, results in unnecessary tire • Don't let the engine idle longer than
• Drive smoothly. Accelerate at a moder- wear. Check the tire pressures at least necessary. If you are waiting (and not
ate rate. Don't make "jack-rabbit" starts once a month. in traffic), turn off your engine and
or full-throttle shifts and maintain a • Be sure that the wheels are aligned restart only when you're ready to go.
steady cruising speed. Don't race correctly. Improper alignment can • Remember, your HYUNDAI does not
between stoplights. Try to adjust your result from hitting curbs or driving too require extended warm-up. As soon as
speed to that of the other traffic so you fast over irregular surfaces. Poor align- the engine is running smoothly, you
don't have to change speeds unneces- ment causes faster tire wear and may can drive away. In very cold weather,
sarily. Avoid heavy traffic whenever also result in other problems as well as however, give your engine a slightly
possible. greater fuel consumption. longer warm-up period.
Always maintain a safe distance from • Keep your car in good condition. For • Don't "lug" or "over-rev" the engine.
other vehicles so you can avoid unnec- better fuel economy and reduced Lugging is driving too slowly in too
essary braking. This also reduces maintenance costs, maintain your car high a gear resulting in the engine
brake wear. in accordance with the maintenance bucking. If this happens, shift to a lower
• Drive at a moderate speed. The faster schedule in Section 7. If you drive your gear. Over-revving is racing the engine
you drive, the more fuel your car uses. car in severe conditions, more frequent beyond its safe limit. This can be avoid-
Driving at a moderate speed, especial- maintenance is required. ed by shifting at the recommended
ly on the highway, is one of the most • Keep your car clean. For maximum speeds.
effective ways to reduce fuel consump- service, your HYUNDAI should be kept • Use your air conditioning sparingly.
tion. clean and free of corrosive materials. It The air conditioning system is operat-
• Don't "ride" the brake or clutch pedal. is especially important that mud, dirt, ed by engine power so your fuel econ-
This can increase fuel consumption ice, etc. not be allowed to accumulate omy is reduced when you use it.
and also increase wear on these com- on the underside of the car. This extra
ponents. In addition, driving with your weight can result in increased fuel con-
foot resting on the brake pedal may sumption and also contribute to corro-
cause the brakes to overheat, which sion.
reduces their effectiveness and may
lead to more serious consequences.
5 22
SPECIAL DRIVING CONDITIONS

Hazardous driving conditions Rocking the vehicle Driving at night
When hazardous driving conditions are If it is necessary to rock the vehicle to Because night driving presents more
encountered such as water, snow, ice, free it from snow, sand, or mud, first turn hazards than driving in the daylight, here
mud, sand, or similar hazards, follow the steering wheel right and left to clear are some important tips to remember:
these suggestions: the area around your front wheels. Then, • Slow down and keep more distance
• Drive cautiously and allow extra dis- shift back and forth between 1st (First) between you and other vehicles, as it
tance for braking. and R (Reverse) in vehicles equipped may be more difficult to see at night,
• Avoid sudden movements in braking or with a manual transmission or R especially in areas where there may
steering. (Reverse) and any forward gear in vehi- not be any street lights.
• When braking with non-ABS brakes cles equipped with an automatic trans- • Adjust your mirrors to reduce the glare
pump the brake pedal with a light up- mission. Do not race the engine, and from other driver's headlights.
and-down motion until the vehicle is spin the wheels as little as possible. If • Keep your headlights clean and prop-
stopped. you are still stuck after a few tries, have erly aimed on vehicles not equipped
the vehicle pulled out by a tow vehicle to with the automatic headlight aiming
avoid engine overheating and possible feature. Dirty or improperly aimed
damage to the transmission. headlights will make it much more diffi-
WARNING - ABS cult to see at night.
Do not pump the brake pedal on a CAUTION • Avoid staring directly at the headlights
vehicle equipped with ABS. of oncoming vehicles. You could be
Prolonged rocking may cause
engine over-heating, transmission temporarily blinded, and it will take
• If stalled in snow, mud, or sand, use damage or failure, and tire damage. several seconds for your eyes to read-
second gear. Accelerate slowly to just to the darkness.
avoid spinning the drive wheels.
• Use sand, rock salt, tire chains, or WARNING - Spinning tires
other non-slip material under the drive
wheels to provide traction when stalled Do not spin the wheels, especially
in ice, snow, or mud. at speeds more than 56 km/h (35
mph). Spinning the wheels at high
speeds when the vehicle is station-
ary could cause a tire to overheat
which could result in tire damage
that may injure bystanders.
5 23
Driving in the rain Driving in flooded areas

Rain and wet roads can make driving Avoid driving through flooded areas
dangerous, especially if you’re not pre- unless you are sure the water is no high-
pared for the slick pavement. Here are a er than the bottom of the wheel hub.
few things to consider when driving in the Drive through any water slowly. Allow
rain: adequate stopping distance because
• A heavy rainfall will make it harder to brake performance may be affected.
see and will increase the distance After driving through water, dry the
needed to stop your vehicle, so slow brakes by gently applying them several
down. times while the vehicle is moving slowly.
• Keep your windshield wiping equip-
ment in good shape. Replace your Driving off-road
windshield wiper blades when they Drive carefully off-road because your
show signs of streaking or missing vehicle may be damaged by rocks or
areas on the windshield. roots of trees. Become familiar with the
• If your tires are not in good condition, off-road conditions where you are going
making a quick stop on wet pavement to drive before you begin driving.
can cause a skid and possibly lead to
an accident. Be sure your tires are in Smooth cornering
good shape.
Avoid braking or gear changing in cor-
• Turn on your headlights to make it eas- ners, especially when roads are wet.
ier for others to see you. Ideally, corners should always be taken
• Driving too fast through large puddles under gentle acceleration. If you follow
can affect your brakes. If you must go these suggestions, tire wear will be held
through puddles, try to drive through to a minimum.
them slowly.
• If you believe you may have gotten
your brakes wet, apply them lightly
while driving until normal braking oper-
ation returns.
5 24
WINTER DRIVING
The more severe weather conditions of Use High Quality Ethylene Change to "Winter Weight" Oil if
winter result in greater wear and other Glycol Coolant Necessary
problems. To minimize the problems of Your HYUNDAI is delivered with high In some climates it is recommended that
winter driving, you should follow these quality ethylene glycol coolant in the cool- a lower viscosity "winter weight" oil be
suggestions: ing system. It is the only type of coolant used during cold weather. See Section 9
that should be used because it helps pre- for recommendations. If you aren't sure
Snowy or Icy Conditions vent corrosion in the cooling system, what weight oil you should use, consult
To drive your vehicle in deep snow, it may lubricates the water pump and prevents your HYUNDAI dealer.
be necessary to use snow tires or to freezing. Be sure to replace or replenish
install tire chains on your tires. If snow your coolant in accordance with the To Keep Locks from Freezing
tires are needed, it is necessary to select maintenance schedule in Section 7.
To keep the locks from freezing, squirt an
tires equivalent in size and type to the Before winter, have your coolant tested to
approved de-icer fluid or glycerine into
original equipment tires. Failure to do so assure that its freezing point is sufficient
the key opening. If a lock is covered with
may adversely affect the safety and han- for the temperatures anticipated during
ice, squirt it with an approved de-icing
dling of your car. Speeding, rapid accel- the winter.
fluid to remove the ice. If the lock is
eration, sudden brake applications, and frozen internally, you may be able to thaw
sharp turns are potentially very haz- Check Battery and Cables it out by using a heated key. Handle the
ardous practices. During deceleration, Winter puts additional burdens on the heated key with care to avoid injury.
use engine braking to the fullest extent. battery system. Visually inspect the bat-
Sudden brake applications on snowy or tery and cables as described in Section 7.
icy roads may cause skids to occur. You Use Approved Anti-Freeze in
The level of charge in your battery can be Window Washer System
need to keep sufficient distance between checked by your HYUNDAI dealer or a
the vehicle in front and your vehicle. Also, service station. To keep the water in the window washer
apply the brake gently. It should be noted system from freezing, add an approved
that installing tire chains on the tire will anti-freeze solution in accordance with
provide a greater driving force, but will instructions on the container. Window
not prevent side skids. washer anti-freeze is available from
HYUNDAI dealers and most auto parts
✽ NOTICE outlets. Do not use engine coolant or
Tire chains are not legal in all provinces. other types of anti-freeze as these may
Check province laws before fitting tire damage the finish.
chains.
5 25
HIGHER SPEED MOTORING

Don't Let Your Parking Brake Carry Emergency Equipment Pre-Trip Inspections
Freeze Depending on the severity of the weath- 1. Tires:
Under some conditions your parking er where you drive your car, you should Adjust the tire inflation pressures to
brake can freeze in the engaged position. carry appropriate emergency equipment. specification. Low tire inflation pressures
This is most likely to happen when there Some of the items you may want to carry will result in overheating and possible
is an accumulation of snow or ice around include tire chains, tow straps or chains, failure of the tires.
or near the rear brakes or if the brakes flashlight, emergency flares, sand, a Avoid using worn or damaged tires which
are wet. If there is a risk the parking shovel, jumper cables, a window scraper, may result in reduced traction or tire fail-
brake may freeze, apply it only temporar- gloves, ground cloth, coveralls, a blanket, ure.
ily while you put the gear selector lever etc.
in first or reverse gear and block the rear
wheels so the car cannot roll. Then ✽ NOTICE
release the parking brake. Never exceed the maximum tire infla-
tion pressure shown on the tires.
Don't Let Ice and Snow 2. Fuel, engine coolant and engine
Accumulate Underneath oil:
Under some conditions, snow and ice High speed travel consumes more fuel
can build up under the fenders and inter- than urban motoring. Do not forget to
fere with the steering. When driving in check both engine coolant and engine
severe winter conditions where this may oil.
happen, you should periodically check
underneath the car to be sure the move-
ment of the front wheels and the steering 3. Drive belt:
components is not obstructed. A loose or damaged drive belt may result
in overheating of the engine.
5 26
TRAILER OR VEHICLE TOWING

If you are considering towing with your Trailer Hitches Trailer Brakes
car, you should first check with your Select the proper hitch and ball combina- If your trailer is equipped with a braking
Province Department of Motor Vehicles tion, making sure that it's location is com- system, make sure it conforms to federal
to determine their legal requirements. patible with that of the trailer or vehicle and/or local regulations and that it is
Since laws vary from province to being towed. properly installed and operating correctly.
province, the requirements for towing Use a quality non-equalizing hitch which
trailers, cars, other types of vehicles, or
apparatus may differ. Ask your HYUNDAI
distributes the tongue load uniformly ✽ NOTICE
throughout the chassis. If you tow a trailer or vehicle, your car
dealer for further details before towing.
will require more frequent maintenance
The hitch should be bolted securely to due to the additional load.
CAUTION the car and installed by a qualified tech-
Do not do any towing with your car nician. DO NOT USE A HITCH
DESIGNED FOR TEMPORARY INSTAL- CAUTION
during its first 1,000 km (600 miles) • Never connect a trailer brake sys-
in order to allow the engine to prop- LATION AND NEVER USE ONE THAT
ATTACHES ONLY TO THE BUMPER. tem directly to the vehicle brake
erly break in. Failure to heed this system.
caution may result in serious
engine or transmission damage. • When towing a trailer on steep
grades (in excess of 6%) pay
close attention to the engine
coolant temperature gauge to
ensure the engine does not over-
heat. If the needle of the coolant
temperature gauge moves across
the dial towards "H" (HOT), pull
over and stop as soon as it is safe
to do so, and allow the engine to
idle until it cools down. You may
proceed once the engine has
cooled sufficiently.
5 27
Safety Chains
Should the hitch connection between
your car and the trailer or vehicle you are
towing fail, the trailer or vehicle could
wander dangerously across other lanes
of traffic and ultimately collide with anoth-
er vehicle. To eliminate this potentially
dangerous situation, safety chains,
attached between your car and the trailer
or towed vehicle, are required in most
Tongue load Total trailer weight Gross Axle Weight Gross Vehicle
provinces.
Weight
C190E01L C190E02L
Trailer Weight Limit 2. The total gross vehicle weight with
Tongue loads can be increased or trailer must not exceed the Gross
decreased by redistributing the load in Vehicle Weight Rating (GVWR)
the trailer. This can be verified by check- shown on the vehicle identification
ing the total weight of the loaded trailer plate. The total gross vehicle weight is
and then checking the load on the the combined weight of the vehicle,
tongue. driver, all passengers and their lug-
gage, cargo, hitch, trailer tongue load
and other optional equipment.
✽ NOTICE
1. Never load the trailer with more
weight in the back than in the front.
About 60% of the trailer load should
be in the front half on the trailer and
the remaining 40% in the rear.
5 28
3. The front or rear axle weight must not Trailer or Vehicle Towing Tips
exceed the Gross Axle Weight Rating WARNING 1. Before towing, check hitch and safety
(GAWR) shown on the vehicle identi- Improperly loading your car and chain connections as well as proper
fication plate. It is possible that your trailer can seriously affect its steer- operation of the trailer running lights,
towing package does not exceed the ing and braking performance caus- brake lights, and turn signals.
GVWR but exceeds the GAWR. ing a crash which could cause seri- 2. Always drive your vehicle at a moder-
Improper trailer loading and/or too ous injury or death. ate speed (Less than 100 km/h).
much luggage in the cargo deck can
overload the rear axle. Redistribute 3. Trailer towing requires more fuel than
the load and check the axle weight normal conditions.
again. 4. To maintain engine braking efficiency,
do not tow a trailer with transmission
in fifth gear.
CAUTION 5. Always secure items in the trailer to
The following specifications are prevent load shift while driving.
recommended when towing a trail- 6. Check the condition and air pressure
er. The loaded trailer weight cannot of all tires on the trailer and your car.
safely exceed the values in the Low tire pressure can seriously affect
chart below. the handling. Also check the spare
tire.
kg. (Lbs)
7. The vehicle/trailer combination is
more affected by crosswind and buf-
Maximum Towable Weight feting.
Trailer *1 Tongue When being passed by a large vehi-
cle, keep a constant speed and steer
With 1200 48 straight ahead. If there is too much
Brake Type (2646) (106) wind buffeting, slow down to get out of
Without 750 48 the other vehicle's air turbulence.
Brake Type (1653) (106)
*1 : 2.6L engine is only available.
5 29
8. When parking your car and trailer, 14. When going down a hill, shift into a
especially on a hill, be sure to follow lower gear and use the engine brak- CAUTION
all the normal precautions. Turn your ing effect. If overheating should occur when
front wheel into the curb, set the park- When ascending a long grade, down- towing, (temperature gauge reads
ing brake firmly, and put the transmis- shift the transmission to a lower gear near red zone), taking the following
sion in 1st or Reverse. In addition, and reduce speed to reduce chances action may reduce or eliminate the
place wheel chocks at each of the of engine overloading and/or over- problem.
trailer's tires. heating. 1. Turn off the air conditioner.
9. If the trailer has electric brakes, start 15. If you have to stop while going uphill, 2. Reduce highway speed.
your vehicle and trailer moving, and do not hold the vehicle in place by 3. Select a lower gear when going
then apply the trailer brake controller pressing on the accelerator. Use the uphill.
by hand to be sure the brakes are parking brake or footbrake. 4. While in stop and go traffic, place
working. This lets you check your elec-
the gear selector in park or neu-
trical connection at the same time.
✽ NOTICE tral and idle the engine at a high-
10. During your trip, check occasionally er speed.
When towing check transmission fluid
to be sure that the load is secure, and
more frequently.
that the lights and any trailer brakes
are still working.
11. Avoid jerky starts, sudden accelera-
tion or sudden stops.
12. Avoid sharp turns and rapid lane
changes.
13. Avoid holding the brake pedal down
too long or too frequently. This could
cause the brakes to overheat, result-
ing in reduced braking efficiency.
5 30
Road warning / 6-2
If the engine will not start / 6-3
Jump starting / 6-4
If the engine overheats / 6-6
Spare tire / 6-7
If you have a flat tire / 6-9
Changing a flat tire / 6-10
Emergency commodity / 6-17
If your vehicle must be towed / 6-18
If you lose your keys / 6-20
What to do in an emergency 6
What to do in an emergency
ROAD WARNING
• The hazard warning flasher operates
whether your vehicle is running or not.
• The turn signals do not work when the
hazard flasher is on.
• Care must be taken when using the
hazard warning flasher while the vehi-
cle is being towed.
OHR047165L
Hazard warning flasher
The hazard warning flasher serves as a
warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emergency
repairs are being made or when the vehi-
cle is stopped near the edge of a road-
way.
Depress the flasher switch with the igni-
tion switch in any position. The flasher
switch is located in the center console
switch panel. All turn signal lights will
flash simultaneously.
6 2
IF THE ENGINE WILL NOT START

If engine turns over normally but
CAUTION does not start
If the engine will not start, do not 1. Check fuel level.
push or pull the car to start it. This
2. With the key in the "OFF" position,
could result in a collision or cause
check all connectors at glow plug and
other damage. In addition, push or
glow plug relay. Reconnect any that
pull starting may cause the catalytic
may be disconnected or loose.
converter to be overloaded and cre-
ate a fire hazard. 3. Check fuel line in the engine room.
4. If engine still refuses to start, call a
HYUNDAI dealer or seek other quali-
fied assistance.
OHR072011
If engine doesn't turn over or If the engine stalls while driving
turns over slowly 1. Reduce your speed gradually, keeping
1. Check the battery connections to be a straight line. Move cautiously off the
sure they are clean and tight. road to a safe place.
2. Turn on the interior light. If the light 2. Turn on your emergency flashers.
dims or goes out when you operate 3. Try to start the engine again. If your
the starter, the battery is discharged. vehicle will not start, contact a
3. Check the starter connections to be HYUNDAI dealer or seek other quali-
sure they are securely tightened. fied assistance.
4. Do not push or pull the vehicle to start
it. See instructions for "Jump Starting".
6 3
JUMP STARTING
If the engine stalls at a crossroad (Continued)
or crossing
• Do not allow the (+) and (-)
• If the engine stalls at a crossroad or jumper cables to touch. It may
crossing, set the shift lever in the N cause sparks.
(Neutral) position and then push the • The battery may rupture or
vehicle to a safe place. explode when you jump start with
• If your vehicle has a manual transmis- a low or frozen battery.
sion not equipped with a ignition lock
switch, the vehicle can move forward
by shifting to the 2 (second) or 3 (third) • If you should accidentally get acid on
gear and then turning the starter with- Discharged battery your skin or in your eyes, immediately
out depressing the clutch pedal. Booster battery remove any contaminated clothing and
OHR042050
flush the area with clear water for at
least 15 minutes. Then promptly obtain
WARNING medical attention. If you must be trans-
• The gas produced by the battery ported to an emergency facility, contin-
during the jump-start operation is ue to apply water to the affected area
highly explosive. If these instruc- with a sponge or cloth.
tions are not followed exactly, • The gas produced by the battery dur-
serious personal injury and dam- ing the jump-start operation is highly
age to the vehicle may occur! If explosive. Do not smoke or allow a
you are not sure how to follow spark or open flame in the vicinity.
this procedure, seek qualified • The battery being used to provide the
assistance. Automobile batteries jump start must be 12-volts. If you can-
contain sulfuric acid. This is poi- not determine that it is a 12-volt bat-
sonous and highly corrosive. tery, do not attempt to use it for the
When jump starting, wear protec- jump start.
tive glasses and be careful not to
get aid on yourself, your clothing
or on the car.
(Continued)
6 4
• To jump start a car with a discharged 5. Start the engine in the car with the dis-
battery, follow this procedure exactly: charged battery using the normal start-
1. If the booster battery is installed in ing procedure. After the engine starts,
another vehicle, be sure the two vehi- leave the jumper cables connected and
cles are not touching. let the engine run at fast idle or about
2. Turn off all unnecessary lights and 2,000 rpm for several minutes.
accessories in both vehicles. 6. Carefully remove the jumper cables in
3. Attach the clamps of the jumper cable the reverse order of attachment.
in the exact order shown in the illustra-
tion. That is, first, attach one clamp of If you do not know why your battery
the jumper cable to the positive (+) post became discharged (because the lights
or cable of the discharged battery. Then were left on, etc.), have the charging sys-
attach the other end of the same cable tem checked by your HYUNDAI dealer. HHR4002
to the positive (+) post or cable of the ✽ NOTICE
booster battery. Next, using the other If your vehicle is equipped with double
cable, attach one clamp to the negative cab, first pull the cushion of the rear seat
(-) post or cable of the booster battery. forward. And remove the battery cover
Then attach the other end of that cable by turning the knob counterclockwise.
to a solid metal part of the vehicle away And then you can jump start the car.
from the battery. Do not connect the
cable to any moving part.
4. Start the engine in the car with the
booster battery and let it run for a few
minutes. This will help to assure that
the booster battery is fully charged.
During the jumping operation, run the
engine in this vehicle at about 2,000
rpm.
6 5
IF THE ENGINE OVERHEATS

If your temperature gauge indicates over- 4. Check to see if the water pump drive
heating, you experience a loss of power, belt is missing. If it is not missing, WARNING
or hear loud pinging or knocking, the check to see that it is tight. If the drive Never work on injection system
engine is probably too hot. If this hap- belt seems to be satisfactory, check with engine running or within 30
pens to you, you should: for coolant leaking from the radiator, seconds after shutting off engine.
hoses or under the car. (If the air con- High pressure pump, rail, injectors
1. Pull off the road and stop as soon as ditioning had been in use, it is normal and high pressure pipes are sub-
it is safe to do so. for cold water to be draining from it ject to high pressure even after the
2. Place the gear selector lever in neutral when you stop). engine stopped. The fuel jet pro-
and set the parking brake. If the air duced by fuel leaks may cause seri-
conditioning is on, turn it off. ous injury, if it touch the body.
WARNING People using pacemakers should
3. If engine coolant is running out under
While the engine is running, keep not move than 30cm closer to the
the car or steam is coming out from
hair, hands, and clothing away from ECU or wiring harness within the
the hood, allow the engine to idle. Do
moving parts such as the fan and engine room while engine is run-
not open the hood until the engine
drive belts to prevent injury. ning, since the high currents in the
coolant has stopped running or the
steaming has stopped. If there is no Common Rail system produce con-
visible loss of engine coolant and no siderable magnetic fields.
steam, leave the engine running, lift
up the passenger's seat and check to
be sure the engine cooling fan is oper- 5. If the water pump drive belt is broken
ating. If the fan is not running, turn the or coolant is leaking out, stop the
engine off. engine immediately and call the near-
est HYUNDAI dealer for assistance.
WARNING
Do not remove the radiator cap
when the engine is hot. This can
allow coolant to be blown out of the
opening and cause serious burns.
6 6
SPARE TIRE
6. If you cannot find the cause of the The following instructions for the FULL
overheating, wait until the engine tem- SIZE spare tire should be observed:
perature has returned to normal.
Then, if the engine coolant has been Check inflation pressure as soon as
lost, carefully add coolant to the reser- practical after installing the spare tire,
voir to bring the fluid level in the reser- and adjust to the specified pressure. The
voir up to the halfway mark. tire pressure should be periodically
7. Proceed with caution, keeping alert for checked and maintained at the specified
further signs of overheating. If over- pressure while the tire is stored.
heating happens again, call a
HYUNDAI dealer for assistance.
Spare Tire Pressure
OHR052109
Tire inflation
CAUTION pressure Handling the Spare Tire
Tire size
• Serious loss of engine coolant 1. Assemble the tools(1)(2)(3) into the
indicates there is a leak in the Front Rear
spare tire carrier wrench orderly like
cooling system and this should the picture.
290 kPa
be checked as soon as possible 195/70R15C-8PR
(42 psi)
- 2. Insert the spare tire carrier wrench into
by a HYUNDAI dealer. the hole of the spare tire carrier, turn it
• When the engine overheats from Low Deck 340kPa counterclockwise, then the spare tire
-
low engine coolant, suddenly (STD) (50PSI)
145R13C-8PR comes down.
adding engine coolant may cause Low Deck 440kPa
-
cracks in the engine. To prevent (DBL) (64PSI)
damage, add engine coolant
195/70R15C- 440kPa
slowly in small quantities. 8PR
High Deck -
(64PSI)
6 7
■ Low Deck
Steel wire
Rear wheel tire
Wheel carrier guide
Rubber cushion
Front wheel tire
Tire support
OHR052110 D040B01HR OHR052111K
■ High Deck
3. Disconnect the steel wire (4) from the 5. Connect the steel wire (4) with the
tire support hook (5) after the spare support hook (5).
tire comes down completely. Steel wire
4. To install the spare tire, build the spare
tire as following and pull the tire sup-
port.
Rear wheel tire
Tire support
D040B03HR
6 8
IF YOU HAVE A FLAT TIRE

If a tire goes flat while you are driving:
1. Take your foot off the accelerator
pedal and let the car slow down while
driving straight ahead. Do not apply
the brakes immediately or attempt to
pull off the road as this may cause a
loss of control. When the car has
slowed to such a speed that it is safe
to do so, brake carefully and pull off
the road. Drive off the road as far as
possible and park on firm, level
ground. If you are on a divided high-
OHR052112 OHR052113 way, do not park in the median area
6. Insert the spare tire carrier wrench Spare tire anti-theft device between the two traffic lanes.
into the hole in the spare tire carrier (if equipped) 2. When the car is stopped, turn on your
and turn it clockwise. emergency hazard flashers, set the
This device is designed to protect the parking brake and put the transmis-
7. After the spare tire fully raised, tighten spare tire theft.
by hand to about 30 kg.f (295 N). sion in reverse.
To unlock the spare tire-anti theft device 3. Have all passengers get out of the car.
Then, remove the spare tire carrier insert the key into the lock, push it once,
wrench with care not to turn it in the Be sure they all get out on the side of
then pull out it with the key. the car that is away from traffic.
reverse direction. Now, ensure that the To lock the spare tire anti-theft device fit
tire is secured in position. 4. Change the tire according to the
the lock connected to the key in the hole instructions provided as following.
of the spare tire carrier, push it once until
CAUTION in "clicks", then pull out the key.
If you cannot secure the spare tire
in position, load it on the cargo
deck and ask your nearest service
shop for inspection.
6 9
CHANGING A FLAT TIRE

The procedure described on the follow- ■ Front
ing pages can be used to rotate tires as
well as to change a flat tire. When prepar-
ing to change a flat tire, check to be sure
the gear selector lever is in reverse gear
and that the parking brake is set, then:
OHR042033
■ Rear
OHR042036
To reinstall the wheel cover fit the
grooves of the wheel cover in the wheel
lug nuts of wheel and hit the center of the
wheel cover with your hand.
CAUTION
Make sure there's nothing behind
you before removing the wheel
OHR052107 cover.
Wheel Cover (if equipped)
To remove the wheel cover insert the rod
(1) into the crack between the wheel and
wheel cover, and pry up the wheel cover
gently with the rod.
6 10
Flat tire
D060F01HR OHR058108
1. Obtain Spare Tire and Tool 2. Block the Wheel 3. Loosen Wheel Nuts
Remove the spare tire and take out the Block the wheel that is diagonally oppo- Assemble the tools(1)(2)(3) into the
jack and tool bag. site from the flat tire to keep the vehicle wheel lug nut wrench orderly like the pic-
To remove the spare tire, refer to from rolling when the car is raised on the ture.
"Handling the Spare Tire" on page 6-7. jack. The wheel nuts should be loosened
To take out the jack, loosen the securing slightly before raising the car. To loosen
unt. the nuts, turn the wrench handle coun-
terclockwise. When doing this, be sure
that the socket is seated completely over
✽ NOTICE the nut so it cannot slip off. For maximum
The spare tire is located underneath leverage, position the wrench so the han-
dle is to the right as shown in the illustra-
tion. Then, while holding the wrench near
the end of the handle, pull up on it with
steady pressure. Do not remove the nuts
at this time. Just loosen them about one-
half turn.
6 11
■ Front After stopping the engine and applying

the parking brake on a flat level surface,
also use chocks to hold the wheels.
Position the jack only at the specified
points indicated in the illustration, and
the use of the jack at other points could
damage the vehicle body.
OHR052116
■ Rear
OHR058119
5. Raising the Car
(1) Assemble the tools(1)(2)(3) into the
jack handle orderly like the picture.
OHR052117
4. Put the Jack in Place
The method for jacking up the vehicle
should be remembered in order to
change a tire in the event of a puncture
and in order to install tire chains.
6 12
Ram
Jack handle
Jack handle
HHR4016 HHR4016A HHR4017

(2)Using the jack handle, turn the (3)Fit the jack handle into the holder, and (4)Move the jack handle up and down to
release valve clockwise until it reach- align the groove of the jack handle (4) raise the ram until just before the jack
es a stop. with the notch of the holder (5). contacts the jacking point of the car.
(5)Position the jack with the jack handle.
Position it only at the specified points
indicated in the "Put the Jack in
Place".
Use of the jack at other points could
damage the car.
(6)Moving the jack handle up and down
to raise the ram. As the jack begins to
raise the vehicle, double check that it
is properly positioned and will not slip.
Raise the car high enough so that the
fully inflated spare tire can be
installed. To do this, you will need
more ground clearance than is
required to remove the flat tire.
6 13
Stop
mark
D060F02HR D060F03HR HHR4018

(7)Using the jack handle, turn the (8)Press the piston down all the way and
release valve counterclockwise slow turn the release valve clockwise as far CAUTION
to lower the ram, and then take out the as possible. • Use only the jack included with
jack. the vehicle and use it only for
changing a wheel.
• Position the jack on a hard level
surface.
• If the release valve is loosened by
turning it 2 or more times in the
counterclockwise direction, the
jack’s oil will leak and the jack
cannot be used.
(Continued)
6 14
(Continued)
• This jack is hydraulic, and the
ram is a two-stage type. When
both rams are raised and the stop
mark(Green paint) of the upper
ram becomes visible, stop jack-
ing immediately. Further exten-
sion of the ram may damage the
jack.
• When the jack is used, be sure
that there is no one in or under
the vehicle. D060G01HR D060G02HR
• When jacking up the vehicle, do
so only until the tires are slightly 6. Changing Wheels
lifted from the ground. It is dan- Loosen the wheel nuts and remove them WARNING
gerous to jack up the vehicle with your fingers. Slide the wheel off the Wheel and wheel covers may have
more than that much. studs and lay it flat so it cannot roll away. sharp edges. Handle them carefully
• It is very dangerous if the jack To put the wheel on the hub, pick up the to avoid possible severe injury.
somehow slips, so never leave spare tire, line up the holes with the studs
Before putting the wheel into place,
the vehicle in the jacked-up posi- and slide the wheel onto them. If this is
be sure that there is nothing on the
tion, and never shake the vehicle difficult, tip the wheel slightly and get the
hub or wheel (such as mud, tar,
while it is raised. top hole in the wheel lined up with the top
gravel, etc.) that interferes with the
stud. Then jiggle the wheel back and
wheel from fitting solidly against
forth until the wheel can be slid over the
the hub. If there is, remove it. If there
other studs.
is not good contact on the mount-
WARNING ing surface between the wheel and
Do not get under the car when it is hub, the wheel nuts could loosen
supported by the jack! This is very and cause the loss of a wheel. Loss
dangerous as the vehicle could fall of a wheel may result in loss of con-
and cause serious injury or death. trol of the vehicle. This may cause
No one should stay in the car while serious injury or death.
the jack is being used.
6 15
After changing wheels

If you have a tire gauge, remove the
valve cap and check the air pressure. If
the pressure is lower than recommend-
ed, drive slowly to the nearest service
station and inflate to the correct pres-
sure. If it is too high, adjust it until it is cor-
rect. Always reinstall the valve cap after
checking or adjusting tire pressure. If the
cap is not replaced, air may leak from the
tire. If you lose a valve cap, buy another
and install it as soon as possible.
D060H01HR OHR058118 After you have changed wheels, always
7. Re-install Wheel Nuts 8. Lower Vehicle and Tighten Nuts secure the flat tire in its place and return
To reinstall the wheel, hold it on the Lower the car to the ground by moving the jack, jack handle, and tools to their
studs, put the wheel nuts on the studs the jack handle up and down. Then posi- proper storage locations.
and tighten them finger tight. The nuts tion the wrench as shown in the drawing
should be installed with their small diam- and tighten the wheel nuts. Be sure the
eter ends directed inward. Jiggle the tire socket is seated completely over the nut.
to be sure it is completely seated, then Do not stand on the wrench handle or
tighten the nuts as much as possible with use an extension pipe over the wrench
your fingers again. handle.
Go around the wheel tightening every
Wheel nut Front Rear
other nut until they are all tight. Then dou-
Tightening Torque ble-check each nut for tightness. After
15~20 15~20 changing wheels, have a technician tight-
(kgf·m)
en the wheel nuts to their proper torque
as soon as possible.
6 16
EMERGENCY COMMODITY (IF EQUIPPED)

There are some emergency commodities ■ Double Cab Triangle Reflector
in the vehicle to help you respond to the Placed the triangle reflector on the road
emergency situation. to warn oncoming vehicles during emer-
gencies, such as when the vehicle is
■ Standard Cab parked by the roadside due to any prob-
lems.
First Aid Kit

There are some items such as scissors,
bandage and adhesive tape and etc. in
the kit to give first aid to an injured per-
D070A02HR son.
If there is small fire and you know how to
Fire extinguisher use the fire extinguisher, take the follow-
ing steps carefully.
D070A01HR
Fire extinguisher 1. Pull the pin at the top of the extin-

guisher that keeps the handle from
The fire extinguisher is located behind being accidentally pressed.
the front seat (Standard Cab) or under
2. Aim the nozzle toward the base of the
the rear seat cushion (Double Cab).
fire.
3. Stand approximately 2.5 m (8 ft) away
✽ NOTICE from the fire and squeeze the handle
If your vehicle is equipped with double to discharge the extinguisher. If you
cab, first pull the cushion of rear seat release the handle, the discharge will
forward to take out the fire extinguisher. stop.
4. Sweep the nozzle back and forth at
the base of the fire. After the fire
appears to be out, watch it carefully
since it may re-ignite.
6 17
IF YOUR VEHICLE MUST BE TOWED

Tire Pressure Gauge (if equipped) If your vehicle has to be towed, it should
You can easily check the tire pressure be done by your HYUNDAI dealer or a
with a tire pressure gauge that is found in commercial tow truck service. This will
OVM tool bag. Tires normally lose some help assure that your vehicle is not dam-
air in day-to-day use, and you may have aged in towing. Also, professionals are
to add a few pounds of air periodically generally aware of local laws governing
and it is not usually a sign of a leaking towing. In any case, rather than risk dam- dolly
tire, but of normal wear. Always check tire age to your car, it is suggested that you
pressure when the tires are cold because show this information to the tow truck
tire pressure increases with temperature. operator. Be sure that a safety chain sys-
tem is used and that all local laws are
observed.
To check the tire pressure, take the fol-
It is recommended that your vehicle be
lowing steps;
towed with a wheel lift and dollies or
1. Unscrew the inflation valve cap that is flatbed equipment with all the wheels off
located on the rim of the tire. the ground.
2. Press and hold the gauge against the
tire valve. Some air will escape as you
begin and more will escape if you CAUTION
don't press the gauge in firmly. • Your vehicle can be damaged if HHR4060
3. A firm non-leaking push will activate towed incorrectly!
the gauge.
Towing the vehicle
• Be sure the transmission is in
4. Read the tire pressure on the gauge neutral. Your vehicle can be towed by wheel lift
to know whether the tire pressure is type truck (1), (2) or flatbed equipment
• When the engine will not start, be (3).
low or high. sure the steering is unlocked by
5. Adjust the tire pressures to the speci- placing the key in the "ACC" posi-
fied pressure. tion.
6. Reinstall the inflation valve cap.
6 18
1) If any of the loaded wheels or suspen-

CAUTION sion components are damaged or the
• When towing the vehicle, take vehicle is being towed with the rear
care not to cause damage to the wheels on the ground, use a towing
bumper or underbody of the vehi- dolly under the rear wheels.
cle. If you do not use a towing dolly, place
the ignition key in the "ACC" position
and put the transmission in "N
(Neutral)".
CAUTION Towing hook

Do not tow with the key removed or OHR042004
in the "LOCK" position when tow-
ing from the front without a towing Emergency towing
dolly. For emergency towing when no commer-
cial tow vehicle is available, attach a tow
HHR4061 cable, chain or strap to the towing hook
under the front of your car. Do not
2) If the vehicle is being towed with the attempt to tow your vehicle in this man-
• Do not tow with sling type truck front wheels on the ground, be sure
as this may cause damage to the ner on any unpaved surface. This may
the parking brake is released. result in serious damage to your car.
bumper or underbody of the vehi-
cle. Nor should it be attempted if the wheels,
3) It is recommended that your vehicle drive train, axles, steering or brakes are
be towed with all the wheels off the damaged. Before towing, be sure the
ground. transmission is in neutral and the key in
"ACC" (with the engine off) or in the "ON"
position (with the engine running). A driv-
er must be in the towed car to steer it and
operate the brakes.
6 19
IF YOU LOSE YOUR KEYS

If you lose your keys, many HYUNDAI
CAUTION dealers can make you a new key if you
If the car is being towed with all four have your key number.
wheels on the ground, it can be If you lock the keys inside your car and
towed only from the front. Be sure you cannot obtain a new key, many
that the transmission is in neutral. HYUNDAI dealers can use special tools
Do not tow at speeds greater than to open the door for you.
50 km/h (25 mph) and for more than
25 km (15 miles).
Be sure the steering is unlocked by
placing the key in the "ACC" posi-
tion. A driver must be in the towed
vehicle to operate the steering and
brakes.
6 20
Front open service panel / 7-3
Engine compartment / 7-4
Maintenance intervals / 7-6
Scheduled maintenance / 7-8
Maintenance under severe usage conditions / 7-12
Explanation of scheduled maintenance items / 7-13
Checking the engine oil / 7-16
Changing the oil and filter / 7-18
Checking and changing the engine coolant / 7-20
Changing the air cleaner filter / 7-23
Windshield wiper blades / 7-23
Filling the washer reservoir / 7-25
Checking the transmission oil (manual) / 7-26
Checking the rear axle oil / 7-26
Maintenance 7
Checking the brakes / 7-28
Air conditioning care / 7-29
Checking the free-play / 7-30
Checking drive belts / 7-31
Tire / 7-32
Checking and replacing fuses / 7-40
Fuse panel description / 7-43
Checking the battery / 7-49
Checking electric cooling fans / 7-51
Power steering fluid level / 7-52
Fuel filter / 7-53
Headlight aiming adjustment / 7-55
Replacement of light bulbs / 7-56
Bulb wattages / 7-63
Emission control system / 7-64
Appearance care / 7-68
7 Maintenance
Maintenance
FRONT OPEN SERVICE PANEL
1. Engine coolant reservoir

2. Air conditioner filter (if equipped)
3. Windshield washer fluid reservoir cap
WARNING
Do not press excessively or step
on the hood.
This can cause the hood to fall
and result in serious injury.
OHR072105L
7 3
Maintenance
ENGINE COMPARTMENT
1. Power steering fluid reservoir

2. Engine oil level dipstick
3. Engine oil filler cap
4. Radiator cap
5. Fuse and relay box
6. Fuel filter

OHR056001/OHR072007/OHR077108
7 4
Maintenance

1. Power steering fluid reservoir

2. Engine oil level dipstick
3. Engine oil filler cap
4. Radiator cap
5. Fuse and relay box
6. Fuel filter

OHR076104L/OHR072007/OHR072010
7 5
Maintenance
MAINTENANCE INTERVALS
Service requirements Maintenance Requirements Specified Scheduled Procedures
To assure that you receive the greatest The maintenance required for your These are the procedures such as
number of kilometers of satisfying opera- HYUNDAI can be divided into three main inspections, adjustments and replace-
tion from your HYUNDAI, certain mainte- areas: ments that are listed in the maintenance
nance procedures must be performed. • Specified scheduled procedures charts starting on page 7-8. These pro-
Although careful design and engineering • General checks cedures must be performed at the inter-
have reduced these to a minimum, those • Do-it-yourself maintenance vals shown in the maintenance schedule
that are required are of the utmost impor- to assure that your warranty remains in
tance. effect. Although it is strongly recom-
It is your responsibility to have these mended that they be performed by the
maintenance procedures performed to factory-trained or distributor-trained tech-
comply with the terms of the warranties nicians at your HYUNDAI dealer, these
covering your new HYUNDAI. The procedures may be performed at any
Service Passport supplied with your new qualified service facility.
vehicle provides further information It is suggested that genuine HYUNDAI
about these warranties. service parts be used for any required
repairs or replacements. Other parts of
equivalent quality such as engine oil,
engine coolant, manual transmission oil,
brake fluid and so on which are not sup-
plied by HYUNDAI Motor Company or its
distributor may be used without affecting
your warranty coverage but you should
always be sure these are equivalent to
the quality of the original HYUNDAI
parts. Your Service Passport provides
further information about your warranty
coverage.
7 6
Maintenance
General Checks Scheduled maintenance require-

These are the regular checks you should ments
perform when you drive your HYUNDAI Inspection should be performed any time
or you fill the fuel tank. a malfunction is experienced or suspect-
ed. Receipts for all emission control sys-
Do-It-Yourself Maintenance tem services should be retained to
demonstrate compliance with conditions
If you are mechanically inclined, own a of the emissions system warranty.
few tools that are required and want to
take the time to do so, you can inspect
and service a number of items.
A Few Tips
Whenever you have your HYUNDAI serv-
iced, keep copies of the service records
in your glove box. This will help ensure
that you can document that the required
procedures have been performed to
keep your warranties in effect.
This is especially important when service
is not performed by an authorized
HYUNDAI dealer.
7 7
Maintenance
SCHEDULED MAINTENANCE
Except European Community
The following maintenance services must be performed to assure good vehicle control and performance. Keep receipts for all vehi-
cle services to protect your warranty. Where both kilometers and time are shown, the frequency of service is determined by
whichever occurs first.
R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary
Kilometers x 1000 5 10 20 30 40 50 60 70 80 90
NO. Description
Months 4 8 16 24 32 40 48 56 64 72
Engine control system maintenance (diesel)
2.5L Engine Replace every 10,000 km or 12 months
1 Engine oil and filter
2.6L Engine Replace every 5,000 km or 6 months *See Note(1)
2 Air cleaner filter See Note(2)
3 Fuel filter* (5) R R R
4 Valve clearance 2.6L Engine Inspect every 20,000 km
5 Injection timing (if exhaust gas includes black smoke) I I I
6 Egr system (valve, tube, hose) I I I
7 Timing belt 2.6L Engine I R
2.5L Engine I I I
8 Drive belt (for water pump and alternator)
2.6L Engine I I I I I I I I I
9 Engine idle speed I I I I
10 Fuel system leaks See Note(3)
11 Injection nozzle (if exhaust gas includes black smoke) I I I
12 Vacuum pump and vacuum hose 2.6L Engine See Note(4)
13 Vacuum pump oil hose 2.6L Engine See Note(4)
Note :(1) Republic of South Africa (If the vehicle is lubricated API CJ-4 grade or above.): (5) This maintenance schedule depends on fuel quality. It is applicable only when using
For every 7,500 KM or 6 months, whichever occurs first : "R" a qualified fuel < “EN590 or equivalent”>. If the diesel fuel specification don’t meet
(2) For China, India and Middle East : For every 15,000 KM or 12 months, whichev- the EN590, it must be replaced more frequently. HYUNDAI recommends “every
er occurs first : "R" 7,500km inspection, every 15,000km replacement” . If there are some important
Except China, India and Middle East : For every 45,000 KM or 36 months, safety matters like fuel flow restriction, surging, loss of power, hard starting problem
whichever occurs first : "R" etc, replace the fuel filter immediately regardless of maintenance schedule and we
(3) Inspect every day. recommend that you consult an authorized HYUNDAI dealer for details.
(4) For every 15,000 KM or 12 months, whichever occurs first : "I"
7 8
Maintenance
Kilometers x 1000 5 10 20 30 40 50 60 70 80 90
NO. Description
Months 4 8 16 24 32 40 48 56 64 72
General maintenance
1 Coolant See Note (1), (2), (3)
2 Manual transmission oil I
3 Rear axle oil I R I R
4 Clutch/brake pedal free-play
See Note (4)
5 Brake oil reservoir
6 Brake hydraulic fluid I I I
7 Front brake pads I I I I I I I I I
8 Front brake calipers/cylinders/disc I I I I
9 Rear brake drums/linings/cylinders I I I I
10 Parking brake I I I I I I I I I
11 Tire condition/pressure I I I I I I I I I
12 Exhaust system/mounting I I I I I I I I I
13 Steering joint/rack/box oil leaks I I I I I I I I I
14 Suspension joint/seals I I I I
15 Front wheel bearing I I I I
16 Coolant hoses I I I I I I I I I
17 Brake pipe corrosion I I I I I I I I I
18 Climate control air filter See Note (5)
19 Air conditioning refrigerant I I I I I I I I I
20 Power steering pump and hoses I I I I I I I I I
21 Propeller shaft I I I
Note :(1) At first, replace at 48,000 km (30,000 miles) or 24 months: after that, replace (3) For your convenience, it can be replaced prior to it's interval when you do mainte-
every 40,000 km (25,000 miles) or 24 months. nance of other items.
(2) When adding coolant, use only a qualified coolant additive for your vehicle and (4) Inspect every day.
never mix hard water in the coolant filled at the factory. An improper coolant (5) Change it 15,000 km or 12 month or more frequently. but, If the field for conditions
mixture can result in serious malfunction or engine damage. below is set, Change it 10,000 km or 6 month or more frequently.
(a) Driving in dusty, rough roads
(b) Driving in heavy dust condition
7 9
Maintenance
For European Community Only

The following maintenance services must be performed to assure good vehicle control and performance. Keep receipts for all vehi-
cle services to protect your warranty. Where both kilometers and time are shown, the frequency of service is determined by
whichever occurs first.
Kilometers x 1000 7.5 15 30 45 60 75 90

NO. Description
Months 6 12 24 36 48 60 72
Engine control system maintenance (diesel)
1 Engine oil and filter R R R R R R
2 Air cleaner filter I I R I I I
3 Fuel system leaks See Note (1)
4 Fuel filter* (2) R R R
5 Egr system (valve, tube, hose) I I I
6 Injection timing (if exhaust gas includes black smoke) I I I
7 Drive belt (for water pump/alternator) I I I
8 Engine idle speed I I I I I I
9 Injection nozzle (if exhaust gas includes black smoke) I I I
Note: (1) Inspect every day.
(2) This maintenance schedule depends on fuel quality. It is applicable only when using a qualified fuel < “EN590 or equivalent”>. If the diesel fuel specification don’t meet the
EN590, it must be replaced more frequently. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard starting problem etc, replace
the fuel filter immediately regardless of maintenance schedule and we recommend that you consult an authorized HYUNDAI dealer for details.
7 10
Maintenance
Kilometers x 1000 7.5 15 30 45 60 75 90
NO. Description
Months 6 12 24 36 48 60 72
General maintenance
1 Coolant See Note (1), (2), (3)
2 Manual transmission oil I
3 Rear axle oil See Note (4)
4 Clutch / brake pedal free-play
See Note (5)
5 Brake oil reservoir
6 Brake hydraulic fluid I I I
7 Front brake pad I I I I I I
8 Front brake calipers/cylinders/disc I I I I I I
9 Rear brake drums/linings/cylinders I I I I I I
10 Parking brake I I I I I I
11 Tire condition/pressure I I I I I I
12 Exhaust system/mounting I I I
13 Steering joint/rack/box/oil leaks I I I I I I
14 Suspension joint/seals I I I
15 Front wheel bearing I I I
16 Coolant hoses I I I
17 Brake pipe corrosion I I I I I I
18 Climate control air filter See Note (6)
19 Air conditioning refrigerant I I I I I I
20 Power steering pump and hoses I I I I I I
21 Propeller shaft I I I
Note :(1) At first, replace at 100,000 km (62,500 miles) or 60 months: after that, replace (4) Inspect every 20,000 km; Replace every 40,000 km.
every 40,000 km (25,000 miles) or 24 months. (5) Inspect every day.
(2) When adding coolant, use only a qualified coolant additive for your vehicle and (6) Change it 15,000 km or 12 month or more frequently. but, If the field for conditions
never mix hard water in the coolant filled at the factory. An improper coolant below is set, Change it 10,000 km or 6 month or more frequently.
mixture can result in serious malfunction or engine damage. (a) Driving in dusty, rough roads
(3) For your convenience, it can be replaced prior to it's interval when you do (b) Driving in heavy dust condition
maintenance of other items.
7 11
Maintenance
MAINTENANCE UNDER SEVERE USAGE CONDITIONS

The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart
below for the appropriate maintenance intervals.
MAINTENANCE DRIVING
MAINTENANCE ITEM MAINTENANCE INTERVALS
OPERATION CONDITION
For E.C Every 7,500 km or 6 months A, B, C, D, E, F, G,
Engine oil and 2.5L Engine R
Except E.C Every 5,000 km or 6 months H, I, J
engine oil filter
2.6L Engine R Every 3,000 km or 6 months A, B, C, D, E, F, G, H, I, K
Air cleaner filter R More frequently C, E
Timing belt R Every 60,000 km or 48 months D, E, F, G
Brake pads, calipers, rotors I More frequently C, D, G, H
Rear brake drums and linings I More frequently C, D, G, H
Steering gear box, linkage & boots I Every 10,000 km or 6 months C, D, E, F
Climate control air filter I More frequently C, E
Manual transmission oil R Every 120,000 km A, C, D, E, F, G, H, I, J
Rear axle oil I or R Every 10,000 km C, D, E, G, I, J
Propeller shaft I Every 15,000 km or 12 months C, E
SEVERE DRIVING CONDITIONS

A - Repeated short distance driving F - Driving in heavy traffic area
B - Extensive idling G - Driving in mountainous areas
C - Driving in dusty conditions H - Towing a trailer or police car, taxi, or commercial type operation
D - Driving in areas using salt or other corrosive materials or in very cold weather I - Driving for patrol car, taxi, commercial car or vehicle towing
E - Driving in the condition of inflowing sand or dust into engine J - Driving over 170 km/h
K - Driving over 140 km/h
7 12
Maintenance
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS

Engine Oil and Filter Fuel Lines, Fuel Hoses Fuel Filter
The engine oil and filter should be and Connections A clogged filter can limit the speed at
changed at those intervals specified in Check the fuel lines, fuel hoses and con- which the vehicle may be driven, damage
the maintenance schedule. If the vehicle nections for leakage and damage. Have the emission system and cause hard
is being driven in severe conditions, a trained technician replace any dam- starting. If an excessive amount of for-
more frequent oil and filter changes are aged or leaking parts immediately. eign matter accumulates in the fuel tank,
required. the filter may require replacement more
frequently.
Valve Clearances (2.6L Engine)
WARNING After installing a new filter, run the engine
Never work on injection system for several minutes, and check for leaks
An incorrect valve clearance will not only with engine running or within 30 at the connections. Fuel filters should be
result in rough engine operation, but will seconds after shutting off engine. installed by trained technicians.
also cause excessive noise and reduced High pressure pump, rail, injectors
engine output. and high pressure pipes are sub-
Inspect valve clearance and adjust as ject to high pressure even after the
required while the engine is hot. engine stopped. The fuel jet pro-
duced by fuel leaks may cause seri-
ous injury, if it touch the body.
People using pacemakers should
not move than 30cm closer to the
ECU or wiring harness within the
engine room while engine is run-
ning, since the high currents in the
Common Rail system produce con-
siderable magnetic fields.
7 13
Maintenance
Vacuum and Crankcase Air Cleaner Filter Timing Belt

Ventilation Hoses A Genuine HYUNDAI air cleaner filter is Inspect all parts related with the timing
Inspect the surface of hoses for evidence recommended when the filter is belt for damage and deformation.
of heat and/or mechanical damage. Hard replaced. Replace any damaged parts immediately.
and brittle rubber, cracking, tears, cuts,
abrasions, and excessive swelling indi- Cooling System Manual Transmission Oil
cate deterioration. Particular attention
should be paid to examining those hose Check the cooling system part, such as Inspect the manual transmission oil
surfaces nearest to high heat sources, radiator, coolant reservoir, hoses and according to the maintenance schedule.
such as the exhaust manifold. connections for leakage and damage.
Inspect the hose routing to assure that
Replace any damaged parts. ✽ NOTICE
the hoses do not come in contact with If the oil level is low, check for possible
any heat source, sharp edges or moving Coolant leaks before adding oil. Do not overfill.
component which might cause heat dam- The coolant should be changed at the
age or mechanical wear. Inspect all hose intervals specified in the maintenance Brake Hoses and Lines
connections, such as clamps and cou- schedule. Visually check for proper installation,
plings, to make sure they are secure, and chafing, cracks, deterioration and any
that no leaks are present. Hoses should Drive Belts leakage. Replace any deteriorated or
be replaced immediately if there is any damaged parts immediately.
evidence of deterioration or damage. Inspect all drive belts (water pump and
alternator) for evidence of cuts, cracks,
excessive wear or oiliness, and replace if Brake Fluid
Vapor Hose and Fuel Filler Cap necessary. Drive belts should be Check brake fluid level in the brake fluid
The vapor hose and fuel filler cap should checked periodically for proper tension reservoir. The level should be between
be inspected at those intervals specified and adjusted as necessary. "MIN" and "MAX" marks on the side of
in the maintenance schedule. Make sure the reservoir. Use only hydraulic brake
that a new vapor hose or fuel filler cap is fluid conforming to DOT 3 or DOT 4.
correctly replaced. CAUTION
When you are inspecting the belt,
place the ignition switch in the
LOCK/OFF or ACC position.
7 14
Maintenance
Rear Brake Drums/linings Suspension Mounting Bolts Wheel Bearing Grease

Parking Brake Check the suspension connections for Check the wheel bearings and grease
Check the rear brake drums and linings looseness or damage. Retighten to the according to the maintenance schedule.
for scoring, burning, leaking fluid, broken specified torque.
parts, and excessive wear. Inspect the Air Conditioning Refrigerant
parking brake system including the park- Steering Gear Box, Linkage &
ing brake lever and cables. Check the air conditioning lines and con-
Boots/Lower arm Ball Joint nections for leakage and damage.
With the vehicle stopped and engine off,
Brake Pads, Calipers and Rotors check for excessive free-play in the
Check the pads for excessive wear, discs steering wheel. Check the linkage for
for run out and wear, and calipers for fluid bends or damage. Check the dust boots
leakage. and ball joints for deterioration, cracks, or
For more information on checking the damage. Replace any damaged parts.
pads or lining wear limit, refer to the
HYUNDAI web site. Power Steering Pump, Belt and
(http://brakemanual.hmc.co.kr) Hoses
Check the power steering pump and
Exhaust Pipe and Muffler hoses for leakage and damage. Replace
Visually inspect the exhaust pipes, muf- any damaged or leaking parts immedi-
fler and hangers for cracks, deterioration, ately. Inspect the power steering belt for
or damage. Start the engine and listen evidence of cuts, cracks, excessive wear,
carefully for any exhaust gas leakage. oiliness and proper tension. Replace or
Tighten connections or replace parts as adjust it if necessary.
necessary.
7 15
Maintenance
CHECKING THE ENGINE OIL (DIESEL ENGINE)

Engine oil is essential to the performance (2)The engine oil quality should meet the ■ 2.5L
and service of the engine. It is suggested following classification :
that you check the oil level at least once
a week or every 500 km in normal use DPF ACEA C2
2.5L Engine
and more often if you are on a trip or driv- Non DPF ACEA A3/B4
ing in severe conditions.
API CF-4 above,
2.6L Engine
Recommended Oil ACEA A3/B4
(1)Select engine oil of the proper SAE

viscosity number according to the ✽ NOTICE
atmospheric temperature. • For 2.5L engine ACEA certificated OHR057004
Recommended viscosity is given in engine oil must be used as a service ■ 2.6L
the following illustration. engine oil.

• Only in case that ACEA engine oil is
not available, engine oil above API
CJ-4 is allowed restrictively.
G030C01HR
To Check the Oil Level
Before checking the oil, warm up the
OHR057300 engine to normal operating temperature
and be sure your car is parked on level
ground. Turn the engine off.
7 16
Maintenance
Wait about ten minutes, then remove the ■ 2.5L 2. Add oil, then check the level again. Do
dipstick, wipe it off, fully reinsert the dip- not overfill.
stick and withdraw it again. Then note the 3. Replace the cap by turning it clock-
highest level the oil has reached on the wise.
dipstick. It should be between the upper
("F") and lower ("L") range.
CAUTION
When you wipe the oil level gauge,
you should wipe it with a clean
cloth. When mixed with debris, it
can cause engine damage.
OHR052005K
■ 2.6L
G030D01HR
Adding Oil
If the oil level is close to or below the "L"
mark, add oil until it reaches the "F"
mark. To add oil:
1. Remove the oil filler cap by turning it

counterclockwise.
7 17
Maintenance
CHANGING THE OIL AND FILTER

Engine oil consumption The engine oil and filter should be
Function of Engine Oil changed at those intervals specified in WARNING
the maintenance schedule in Section 7. If Be very careful when draining the
Engine oil has the primary function of
the car is being driven in severe condi- engine oil as it may be hot enough
lubricating and cooling the inside of the
tions, more frequent oil and filter to burn you!
engine.
changes are required.
Engine oil consumption The procedure for changing the oil and 4. When the oil has stopped draining,
It is normal that an engine should con- filter is as follows: replace the drain plug using a new
sume some engine oil while normal driv- 1. Park the car on level ground and set gasket and retighten by turning it
ing. The cause of oil consumption in a nor- the parking brake. Start the engine clockwise.
mal engine are as follows; and let it warm up until the needle on Tightening torque : 3.5 ~ 4.5 kgf.m
the coolant temperature gauge moves 5. Remove the oil filter by turning it coun-
• Engine oil is used to lubricate pistons, above the lowest mark. Turn the terclockwise with a oil filter wrench of
piston rings and cylinders. engine off and place the gear selector the proper size. A certain amount of oil
A thin film of oil is left on the cylinder wall lever in reverse gear. will come out when you remove the fil-
when a piston moves downwards in the 2. Lift up the front passenger's seat and ter. So be sure to have your drain pan
cylinder. High negative pressure gener- remove the engine oil filler cap. in place underneath it.
ated during engine operation sucks 3. Slide underneath the car and loosen 6. Install a new oil filter in accordance
some of the oil into the combustion the drain plug by turning it counter- with the instructions on the carton or
chamber. clockwise with a wrench of the proper on the filter itself. Do not over-tighten.
This oil with some oil of the cylinder wall size. Be sure that a drain pan is in Tightening torque: 2.3 ~ 2.5 kgf.m
is burned by the high temperature composition to catch the oil as it drains Be sure that the mounting surface on
bustion gases during the combustion out, then remove the drain plug. the engine is clean and that the old gas-
process. ket is removed completely. Lubricate
• The engine oil consumption is strongly the new gasket on the filter with clean
effected by the viscosity and quality of engine oil before installation.
oil, engine rpm and driving condition etc.
The engine oil is more consumed under
severe driving conditions such as high
speeds and frequent acceleration and
deceleration than normal driving condi-
tion.
7 18
Maintenance
7. Remove the engine oil level dipstick. ✽ NOTICE

8. Refill the crankcase with the recom- Always dispose of used engine oil in an
mended engine oil slowly. environmentally acceptable manner. It
is suggested that it be placed in a sealed
container and taken to a service station
CAUTION for reclamation. Do not pour the oil on
• Slowly pour the recommended oil the ground or put it into the household
by using a funnel. trash.
• Do not spill engine oil, when
adding or changing engine oil. If
you drop the engine oil on the WARNING
engine room, wipe it off immedi- Used motor oil may cause irritation
ately. or cancer of the skin if left in con-
tact with the skin for prolonged
periods of time. Wash your hands
9. Start the engine and check to be sure thoroughly with soap and warm
no oil is leaking from the drain plug or water as soon as possible after
oil filter. handling used oil.
10. Shut off the engine and recheck the
oil level.
7 19
Maintenance
CHECKING AND CHANGING THE ENGINE COOLANT

(Continued)
Recommended Engine Coolant
CAUTION Use a high quality ethylene-glycol
• Do not drive with no engine • Turn the engine off and wait until
it cools down. Use extreme care coolant in a 50/50 mix with water. The
coolant. It may cause water pump engine coolant should be compatible with
failure and engine seizure, etc. when removing the radiator cap.
Wrap a thick towel around it, and aluminum engine parts. Additional corro-
• When the engine overheats from sion inhibitors or additives should not be
turn it counterclockwise slowly to
low engine coolant, suddenly used. The cooling system must be main-
the first stop. Step back while the
adding engine coolant may cause tained with the correct concentration and
pressure is released from the
cracks in the engine. To prevent type of engine coolant to prevent freezing
cooling system. When you are
damage, add engine coolant and corrosion. Never allow the concen-
sure all the pressure has been
slowly in small quantities. tration of antifreeze to exceed the 60%
released, press down on the cap,
using a thick towel, and continue level or go below the 35% level, or dam-
turning counterclockwise to age to the cooling system may result. For
remove it. proper concentration when adding or
WARNING replacing the engine coolant, refer to the
• Even if the engine is not operat-
Removing radiator following table.
ing, do not remove the radiator
cap cap or the drain plug while the
Engine coolant
engine and radiator are hot. Hot
Ambient concentration
coolant and steam may still blow
out under pressure, causing seri- Temperature Antifreeze
Water
• Never attempt to remove the radi- ous injury. solution
ator cap while the engine is oper- -15°C (5°F) 35% 65%
ating or hot. Doing so might lead -25°C (-13°F) 40% 60%
to cooling system and engine -35°C (-31°F) 50% 50%
damage and could result in seri-
-45°C (-49°F) 60% 40%
ous personal injury from escap-
ing hot coolant or steam.
(Continued)
7 20
Maintenance
To Change the Coolant

The coolant should be changed at those
intervals specified in the vehicle mainte-
nance schedule in Section 7.
CAUTION
Engine coolant can damage the fin-
ish of your car. If you spill engine
coolant on the car, wash it off thor-
oughly with clean water.
OHR052010 1. Park the car on level ground, set the OHR072006

To Check the Coolant Level parking brake and lift up the front pas- 2. Turn the radiator cap counterclock-
The coolant level can be seen on the senger's seat. wise without pressing down on it, until
side of the plastic coolant reservoir. The it stops. This relieves any pressure
level of the coolant should be between remaining in the cooling system. And
the "L" and "F" lines on the reservoir remove the radiator cap by pushing
when the engine is cold. If the level is down and turning counterclockwise.
below the "L" mark, add engine coolant
to bring it up between "L" and "F". If the
level is low, inspect for coolant leaks and
recheck the fluid level frequently. If the
level drops again, visit your HYUNDAI
dealer for an inspection and diagnosis of
the reason.
7 21
Maintenance
6. Start the engine, top off the radiator

WARNING with water, open the hood and then
Radiator cap add engine coolant to the reservoir
until the level is between "L" and "F".
Do not remove the radi-
ator cap when the 7. Replace the radiator and reservoir
engine and radiator are caps and check to be sure the drain
hot. Scalding hot cocks are fully closed and not leaking.
coolant and steam may blow out
under pressure causing serious
injury. WARNING
The electric motor (cool-
ing fan) is controlled by
3. Be sure your drain receptacle is in engine coolant tempera-
place. Open the drain cock on the ture, refrigerant pres-
radiator. Allow all the engine coolant to sure and vehicle speed.
drain from the cooling system, then It may someimes operate even
securely close the drain cock. when the engine is not running.
4. Check Section 9 for the capacity of the Use extreme caution when working
cooling system in your car. Then, fol- near the blades of the cooling fan
lowing the manufacturer's directions so that you are not injured by a
on the engine coolant container, add rotating fan blades. As the engine
the appropriate quantity of coolant to coolant temperature decreases, the
the radiator. electric motor will automatically
5. Fill the radiator with clean demineral- shut off. This is a normal condition.
ized or distilled water. Continue to add
clean demineralized or distilled water
in small quantities until the fluid level
stays up in the radiator neck.
7 22
Maintenance
CHANGING THE AIR CLEANER FILTER WINDSHIELD WIPER BLADES
CAUTION
• Operating your vehicle without a
proper air filter in place can
result in excessive engine wear.
• When removing the air cleaner fil-
ter, be careful that dust or dirt
does not enter the air intake.
These may result in damage to
the air cleaner filter.
HHR5013 OHR052024
The air cleaner filter is located in front of The wiper blades should be carefully
the front tire on the right side. inspected from time to time and cleaned
The replacement of air cleaner filter is to remove accumulations of road film or
performed in the following manner. other debris. To clean the wiper blades
and arms, use a clean sponge or cloth
1. Unsnap the clips around the cover. with a mild soap or detergent and water.
If the wipers continue to streak or smear
2. When this is done, the cover can be the glass, replace them with Genuine
taken off, the old filter removed and HYUNDAI Replacement parts or their
the new filter put in its place. equivalent.
Genuine HYUNDAI replacement parts

are recommended. CAUTION
• Do not operate the wipers on dry
glass. This can result in more
rapid wear of the wiper blades
and may scratch the glass.
• Keep the blade rubber out of con-
tact with petroleum products
such as engine oil, gasoline, etc.
7 23
Maintenance
Replacing the Wiper Blades

To replace the wiper blades, raise the
wiper to the vertical.
HHR5049 HHR5050
2. Raise the wiper blade lightly and pull To install the wiper blade
up it. 1. Put a new wiper blade onto the wiper
arm and lower the wiper blade at the
HHR5048
level of the wiper arm as shown in the
drawing.
To remove the wiper blade
1. Push down the wiper blade with the
locking clip (1) pressed to detach it
from the wiper arm.
7 24
Maintenance
FILLING THE WASHER RESERVOIR
CAUTION
• Radiator antifreeze (engine
coolant) should not be used in
the washer system because it will
damage the car's finish.
• The washer should not be operat-
ed if the washer reservoir is
empty. This can damage the
washer fluid pump.
HHR5051 OHR052016
2. Pull up the wiper blade until you hear The washer fluid reservoir supplies fluid WARNING
an audible "click" to engage in the end to the windshield washer system. • Windshield washer fluid agents
of the wiper arm. A good quality washer fluid should be contain some amounts of alcohol
used to fill the washer reservoir. The fluid and can be flammable under cer-
✽ NOTICE level should be checked more frequently tain circumstances. Do not allow
Do not allow the wiper arm to fall during inclement weather or whenever sparks or flame to contact the
against the windshield. the washer system is in more frequent washer fluid or the washer fluid
use. reservoir. Damage to the vehicle
The capacity of the washer reservoir is or its occupants could occur.
2.0 liters. • Windshield washer fluid is poi-
sonous to humans and animals.
Do not drink windshield washer
fluid. Serious injury or death
could occur.
7 25
Maintenance
CHECKING THE TRANSMIS- CHECKING THE REAR AXLE OIL

SION OIL (MANUAL) Rear Axle Oil Capacity
When checking the transmission oil or The oil capacity of the rear axle is 1.6
replacing it according to the maintenance liters.
schedule, We recommend that you have
your vehicle inspected by an authorized
HYUNDAI dealer. WARNING
The rear axle oil should be checked
when the engine is cool or cold. If the
engine is hot, you should exercise
great caution to avoid burning your-
self on hot engine or exhaust parts.
Filler plug
Drain plug
G130A01HR
Rear axle oil should be checked at those
intervals specified in the vehicle mainte-
nance schedule in Section 7.
7 26
Maintenance
✽ NOTICE
We recommend that the rear axle oil be
14mm checked by an authorized HYUNDAI
dealer.
G130B01HR
To Check the Rear Axle Oil Level
Park the car on level ground with the
engine off.
1. Using a wrench of the correct size,

loosen the oil filler plug by turning it
counterclockwise and remove it with
your fingers.
2. Use a suitable tool to feel inside the
hole. The oil level should be within 14
mm from its bottom edge. If it is not,
check for leaks before adding oil. To
refill the rear axle or bring the oil level
up,add oil slowly until it reaches the
proper level. Do not overfill.
3. Replace the plug and washer, screw it
in with your fingers and then tighten
securely with the wrench.
7 27
Maintenance
CHECKING THE BRAKES

Recommended Brake Fluid ■ Left-hand Drive type
CAUTION Use only hydraulic brake fluid conforming
Because brakes are essential to the to DOT 3 or DOT 4 specifications in your
safe operation of the car, it is sug- braking system. Follow the instructions
gested that they be checked and printed on the container.
inspected by your HYUNDAI dealer.
The brakes should be checked and
inspected for wear at those inter- ✽ NOTICE
vals specified in the vehicle mainte- Before removing the brake filler cap,
nance schedule in Section 7. read the warning on cap.
HHR5015
WARNING ■ Right-hand Drive type
Checking the Brake Fluid Level
Clean filler cap before removing.
Use only DOT3 or DOT4 brake fluid
WARNING from a sealed container.
Use caution when handling brake
fluid. It can damage your vision if it
gets into your eyes. It will also dam-
age your vehicle's paint if spilled
on it and not removed immediately.
HHR5015-E
To Check the Fluid Level
The fluid level in the brake fluid reservoir
should be checked periodically. The level
should be between the "MIN" and "MAX"
marks on the side of the reservoir. If the
level is at or below the "MIN" mark, care-
fully add fluid to bring it up to "MAX". Do
not overfill.
7 28
Maintenance
AIR CONDITIONING CARE

Adding Brake Fluid Keeping the Condenser Clean Lubrication
The air conditioning condenser (and To lubricate the compressor and the
engine radiator) should be checked peri- seals in the system, the air conditioning
WARNING odically for accumulation of dirt, dead should be run for at least 10 minutes
Handle brake fluid carefully. It can insects, leaves, etc. These can interfere each week. This is particularly important
damage your vision if it gets into with maximum cooling efficiency. When during cool weather when the air condi-
your eyes. Use only DOT 3 or DOT 4 removing such accumulations, brush or tioning system is not otherwise in use.
specification fluid from a sealed hose them away carefully to avoid bend-
container. Do not allow the fluid can ing the cooling fans.
or reservoir to remain open any
longer than required. This will pre-
vent entry of dirt and moisture Checking the Air Conditioning
which can damage the brake sys- Operation
tem and cause improper operation. 1. Start the engine and let it run at a fast
idle for several minutes with the air
To add brake fluid, pull up the cover, wipe conditioning set at the maximum cold
away any dirt, and open the fluid reser- setting.
voir cap. Slowly pour the recommended 2. If the air coming out of the in-dash
fluid into the reservoir. Do not overfill. vents is not cold, have the air condi-
Carefully replace the cap on the reservoir tioning system inspected by your
and tighten. HYUNDAI dealer.
CAUTION
Running the air conditioning sys-
tem for extended periods of time
with a low refrigerant level may
damage the compressor.
7 29
Maintenance
CHECKING THE FREE-PLAY

✽ NOTICE
• If you clean the filter with water, dry
it in the open air.
• When cleaning the filter, be careful
that the filter doesn’t drop or bump
against other objects, or damage may
result.
30 mm
(1.18 in.)
OHR022093 OHR052023
Checking the climate control air Steering wheel
filter (For Evaporator and Blower To check the steering wheel free-play,
Unit) (if equipped) stop the car with the wheels pointed
The climate control air filter is located in straight ahead and gently move the
the hood. steering wheel back and forth. Use very
It helps to decrease the amount of pollu- light finger pressure and be sensitive to
tants entering the car. changes in resistance that mark the lim-
its of the freeplay. If the free-play is
greater than specified, have it inspected
1. Open the hood. by your HYUNDAI dealer and adjusted or
2. Remove the filter by pressing the repaired if necessary.
upper end of the filter.
3. Replace the climate control air filter.
4. Reassemble in the reverse order of
disassembly.
7 30
Maintenance
CHECKING DRIVE BELTS

Drive belts should be checked periodical-
ly for proper tension and adjusted if nec-
essary.
At the same time, belts should be exam-
ined for cracks, wear, fraying or other evi-
dence of deterioration and replaced if
necessary.
6 ~ 13 mm 3 ~ 8 mm
(0.24 ~ 0.51 in.) (0.12 ~ 0.31 in.)
Belt routing should also be checked to be
sure there is no interference between the
belts and other parts of the engine. After
a belt is replaced, the new belt should be
adjusted again after two or three weeks
G160A01HR G160A01HR to eliminate slack resulting from initial
Clutch pedal Brake pedal stretching after use.
With the engine off, press lightly on the With the engine off, press down on the
clutch pedal until you feel a change in brake pedal several times to reduce the WARNING
resistance. This is the clutch pedal free- vacuum in the brake booster.
The drive belt should be checked
play. The free-play should be within the Then, using your hand, press down slow- when the engine is cool or cold to
limits specified in the illustration. If it is ly on the brake pedal until you feel a avoid burning yourself on hot
not, have it inspected by your HYUNDAI change in resistance. This is the brake engine.
dealer and adjusted or repaired if neces- pedal free-play.
sary. The free-play should be within the limits
specified in the illustration. If it is not,
have it inspected by your HYUNDAI deal- CAUTION
er and adjusted or repaired if necessary. When you are inspecting the belt,
place the ignition switch in the
LOCK/OFF or ACC position.
7 31
Maintenance
TIRE
Tire inflation
pressure CAUTION
Tire size
Always observe the following:
Front Rear
• Check pressures when the tires
290 kPa are cold. That is, after the car has
195/70R15C-8PR - been parked for at least three
(42 psi)
hours and hasn't been driven
Low Deck 340kPa more than 1.6 km or one mile
- since starting up.
(STD) (50PSI)
145R13C-
8PR
• Check the pressure of your spare
Low Deck
-
440kPa tire each time you check the pres-
(DBL) (64PSI) sure of other tires.
OHR062002
Recommended inflation 195/70R15C 440kPa
High Deck -
-8PR (64PSI)
pressures
The tire label located on the driver's side
of the center pillar outer panel gives the These pressures were chosen to provide
tire pressures recommended for your car. the most satisfactory combination of ride
comfort, tire wear and stability under nor-
mal conditions. Tire pressures should be
checked at least monthly. Proper tire
inflation pressures should be maintained
for these reasons:
• Lower-than-recommended tire pres-
sures cause uneven tread wear and
poor handling.
• Higher-than-recommended tire pres-
sures increase the chance of damage
from impacts and cause uneven tread
wear.
7 32
Maintenance
Snow tires Tire chains ■ With Spare tire
If you equip your car with snow tires, they Tire chains, if necessary should be
should be the same size and have the installed on the rear wheels. Be sure that
same load capacity as the original tires. the chains are installed in accordance
Snow tires should be installed on all four with the manufacturer's instructions.
wheels; otherwise, poor handling may To minimize tire and chain wear, do not
result. continue to use tire chains when they are
Snow tires should carry 28 kPa (4 psi) no longer needed.
more air pressure than the pressure rec-
ommended for the standard tires on the
tire label on the driver's door edge, or up WARNING
to the maximum pressure shown on the • When driving on roads covered
with snow or ice, drive at less than HHR5019
tire sidewall whichever is less.
30 km/h (20 mph). ■ Without Spare tire
Do not drive faster than 120 km/h (75
mph) when your car is equipped with • Use the SAE "S" class or wire &
snow tires. plastic chains.
• If you have noise caused by chains
contacting the body, retighten the
chain to avoid contact with the
vehicle body.
• To prevent body damage, retighten
the chains after driving 0.5 ~ 1 km.
HHR5020
Tire rotation
Tires should be rotated every 5,000 km
(3,000 miles). If you notice that tires are
wearing unevenly between rotations, we
recommend that the system be checked
by an authorized HYUNDAI dealer so the
cause may be corrected.
7 33
Maintenance
After rotating, adjust the tire pressures Tire balancing

1.6 mm (0.06 in.)
and be sure to check wheel nut torque. A tire that is out of balance may affect
handling and tire wear. The tires on your
HYUNDAI were balanced before the car
WARNING was delivered but may need balancing
Do not mix bias-ply and radial-ply again during the years you own the car.
tires under any circumstances. This
Whenever a tire is dismounted for repair,
may cause dangerous handling
it should be rebalanced before being
characteristics.
reinstalled on the car.
Wear indicator
Tire traction
Tire traction can be reduced if you drive OHR042101
on worn tires, tires that are improperly
inflated or on slippery road surfaces. When to replace tires
Tires should be replaced when tread The original tires on your car have tread
wear indicators appear. To reduce the wear indicators. The tread wear indica-
possibility of losing control, slow down tors appear when the tread depth is 1.6
whenever there is rain, snow or ice on mm (0.06 in.). The tire should be
the road. replaced when these appear as a solid
bar across two or more grooves of the
tread. Always replace your tires with
those of the recommended size. If you
change wheels, the new wheel's rim
width and offset must meet HYUNDAI
specification.
7 34
Maintenance
1
CAUTION WARNING
When replacing the tires, recheck • Driving on worn-out tires is dan- 5,6
and tighten the wheel nuts after gerous! Worn-out tires can cause 7
driving about 1,000 km(620miles). If loss of braking effectiveness,
the steering wheel shakes or the steering control and traction. 4
vehicle vibrates while driving, the When replacing tires, never mix
tire is out of balance. Align the tire radial and bias-ply tires on the
balance. same car. If you replace radial 2
If the problem is not solved, we rec- tires with bias-ply tires, they must 3
ommend that you contact an be installed in sets of four.
authorized HYUNDAI dealer. • Using tires and wheels of other
1 I030B04JM
than the recommended sizes may
cause unusual handling charac- Tire sidewall labeling
teristics that may cause death,
This information identifies and describes
serious injury or property dam-
the fundamental characteristics of the
age.
tire and also provides the tire identifica-
• Tires degrade over time, even tion number (TIN) for safety standard
when they are not being used. certification. The TIN can be used to
Regardless of the remaining identify the tire in case of a recall.
tread, it is recommended that
tires tread, It is recommended
that tires generally be replaced 1. Manufacturer or brand name
after 6 years of normal service. Manufacturer or Brand name is shown.
Heat caused by not climates or
frequent high loading Conditions
can accelerate the aging process.
Failure to follow this Warning can
result in sudden tire failure,
which could lead to a loss of con-
trol and an accident involving
serious injury or death.
7 35
Maintenance
2. Tire size designation Wheel size designation Tire speed ratings

A tire’s sidewall is marked with a tire size Wheels are also marked with important The chart below lists many of the differ-
designation. You will need this informa- information that you need if you ever ent speed ratings currently being used
tion when selecting replacement tires for have to replace one. The following for passenger car tires. The speed rating
your vehicle. The following explains what explains what the letters and numbers in is part of the tire size designation on the
the letters and numbers in the tire size the wheel size designation mean. sidewall of the tire. This symbol corre-
designation mean. sponds to that tire's designed maximum
Example tire size designation: Example wheel size designation: safe operating speed.
(These numbers are provided as an 5.5JX15
example only; your tire size designator Speed
could vary depending on your vehicle.) 5.5 - Rim width in inches. Rating Maximum Speed
195/70R 15C 95V Symbol
J - Rim contour designation.
15 - Rim diameter in inches. S 180 km/h (112 mph)
195 - Tire width in millimeters. T 190 km/h (118 mph)
70 - Aspect ratio. The tire’s section height H 210 km/h (130 mph)
as a percentage of its width.
V 240 km/h (149 mph)
R - Tire construction code (Radial).
15 - Rim diameter in inches. Z Above 240 km/h (149 mph)
C - Commercial tire
95 - Load Index, a numerical code asso-
ciated with the maximum load the
tire can carry.
V - Speed Rating Symbol. See the speed
rating chart in this section for addi-
tional information.
7 36
Maintenance
3. Checking tire life (TIN : Tire 4. Tire ply composition and material
Identification Number) WARNING - Tire age The number of layers or plies of rubber-
Any tires that are over 6 years old, based Tires degrade over time, even when coated fabric in the tire. Tire manufactur-
on the manufacturing date, (including the they are not being used. ers also must indicate the materials in
spare tire) should be replaced by new Regardless of the remaining tread, the tire, which include steel, nylon, poly-
ones. You can find the manufacturing we recommend that tires be ester, and others. The letter "R" means
date on the tire sidewall (possibly on the replaced after approximately six (6) radial ply construction; the letter "D"
inside of the wheel), displaying the DOT years of normal service. Heat means diagonal or bias ply construction;
Code. The DOT Code is a series of num- caused by hot climates or frequent and the letter "B" means belted-bias ply
bers on a tire consisting of numbers and high loading conditions can accel- construction.
English letters. The manufacturing date is erate the aging process. Failure to
designated by the last four digits (charac- follow this warning can result in 5. Maximum permissible inflation
ters) of the DOT code. sudden tire failure, which could pressure
lead to a loss of control and an This number is the greatest amount of air
DOT : XXXX XXXX OOOO accident involving serious injury or pressure that should be put in the tire. Do
The front part of the DOT means a plant death. not exceed the maximum permissible
code number, tire size and tread pattern inflation pressure. Refer to the Tire and
and the last four numbers indicate week Loading Information label for recom-
and year manufactured. mended inflation pressure.
For example:
DOT XXXX XXXX 1517 represents that 6. Maximum load rating
the tire was produced in the 15th week of This number indicates the maximum load
2017. in kilograms and pounds that can be car-
ried by the tire. When replacing the tires
on the vehicle, always use a tire that has
the same load rating as the factory
installed tire.
7 37
Maintenance
7. Uniform tire quality grading Traction - AA, A, B & C Temperature -A, B & C
Quality grades can be found where appli- The traction grades, from highest to low- The temperature grades are A (the high-
cable on the tire sidewall between tread est, are AA, A, B and C. Those grades est), B, and C, representing the tire’s
shoulder and maximum section width. represent the tire’s ability to stop on wet resistance to the generation of heat and
For example: pavement as measured under controlled its ability to dissipate heat when tested
TREADWEAR 200 conditions on specified government test under controlled conditions on a speci-
TRACTION AA surfaces of asphalt and concrete. A tire fied indoor laboratory test wheel.
marked C may have poor traction per- Sustained high temperature can cause
TEMPERATURE A formance. the material of the tire to degenerate and
reduce tire life, and excessive tempera-
Tread wear ture can lead to sudden tire failure.
The tread wear grade is a comparative WARNING Grades B and A represent higher levels
rating based on the wear rate of the tire The traction grade assigned to this of performance on the laboratory test
when tested under controlled conditions tire is based on straight-ahead wheel than the minimum required by law.
on a specified government test course. braking traction tests, and does not
For example, a tire graded 150 would include acceleration, cornering,
wear one-and-a-half times (1½) as well hydroplaning, or peak traction WARNING - Tire tempera-
on the government course as a tire grad- characteristics. ture
ed 100. The temperature grade for this tire
The relative performance of tires is established for a tire that is prop-
depends upon the actual conditions of erly inflated and not overloaded.
their use, however, and may depart sig- Excessive speed, underinflation, or
nificantly from the norm due to variations excessive loading, either separate-
in driving habits, service practices and ly or in combination, can cause
differences in road characteristics and heat build-up and possible sudden
climate. tire failure. This can cause loss of
These grades are molded on the side- vehicle control and serious injury
walls of passenger vehicle tires. The tires or death.
available as standard or optional equip-
ment on your vehicle may vary with
respect to grade.
7 38
Maintenance
Low aspect ratio tire (if equipped) (Continued)

Low aspect ratio tires, whose aspect ratio - If the tire is impacted, we recom-
is lower than 50, are provided for sporty mend that you inspect the tire
looks. condition or contact an author-
Because the low aspect ratio tires are ized HYUNDAI dealer.
optimized for handling and braking, it - To prevent damage to the tire,
may be more uncomfortable to ride in inspect the tire condition and
and there is more noise compare with pressure every 3,000km.
normal tires.
CAUTION
Because the sidewall of the low CAUTION
I100A01HRA • It is not easy to recognize the tire
aspect ratio tire is shorter than the
Spare tire and tools normal, the wheel and tire of the low damage with your own eyes. But
Your HYUNDAI is delivered with the fol- aspect ratio tire is easier to be dam- if there is the slightest hint of tire
lowing: aged. So, follow the instructions damage, even though you cannot
below. see the tire damage with your
- When driving on a rough road or own eyes, have the tire checked
Spare tire and wheel or replaced because the tire dam-
Jack, Jack handle off road, drive cautiously because
tires and wheels may be damage may cause air leakage from
Wheel nut wrench, the tire.
aged. And after driving, inspect
Spare tire carrier wrench tires and wheels. • If the tire is damaged by driving
- When passing over a pothole, on a rough road, off road, pothole,
speed bump, manhole, or curb manhole, or curb stone, it will not
stone, drive slowly so that the be covered by the warranty.
tires and wheels are not dam- • You can find out the tire informa-
aged. tion on the tire sidewall.
(Continued)
7 39
Maintenance
CHECKING AND REPLACING FUSES

Replacing a Fusible Link ✽ NOTICE
A fusible link will melt if the electrical cir- The actual fuse/relay panel label may
cuits from the battery are ever over- differ from equipped items.
loaded, thus preventing damage to the
entire wiring harness. (This could be
caused by a short in the system drawing
too much current.) If this ever happens,
have a HYUNDAI dealer determine the
cause, repair the system and replace the
fusible link. The fusible links are located
in a fuse box for easy inspection.
HHR4003
CAUTION Replacing Accessory Fuse
When replacing a fusible link, never The fuse box for the lights and other elec-
use anything but a new fusible link OHR072007L trical accessories will be found low on the
with the same or lower amperage dashboard on the driver's side. Inside the
rating. Never use a piece of wire or box you will find a list showing the circuits
a higher-rated fusible link. This ✽ NOTICE protected by each fuse.
could result in serious damage and • To replace a fusible link, first tilt the If any of your car's lights or other electri-
create a fire hazard. driver's seatback forward. cal accessories stop working, a blown
• To open the fuse box cover, press the fuse could be the reason. If the fuse has
hook of the cover and pull up the burned out, you will see that the metal
cover. strip inside the fuse has burned through.
WARNING
If you suspect a blown fuse, follow this
Never install a wire or aluminum foil procedure:
instead of the proper fuse - even as
a temporary repair. It may cause 1. Turn off the ignition and all other
extensive wiring damage and a switches.
possible fire.
7 40
Maintenance
2. Open the fuse box and examine each

fuse. Remove each fuse by pulling it
toward you (a small "fuse puller" tool
is contained in the fuse box cover to
simplify this operation).
3. Be sure to check all other fuses even
if you find one that appears to have
burned out.
Good Burned out

G200B01HR G200B02L
4. Replace the blown fuse by pressing a
new fuse of the same rating into place. CAUTION
The fuse should be a snug fit. If it is A burned-out fuse indicates that
not, have the fuse clip repaired or there is a problem in the electrical
replaced by a HYUNDAI dealer. If you circuit. If you replace a fuse and it
do not have a spare fuse, you may be blows as soon as the accessory is
able to borrow a fuse of the same or turned on, the problem is serious
lower rating from an accessory you and should be referred to a
can temporarily get along without (the HYUNDAI dealer for diagnosis and
radio or cigarette lighter, for example). repair. Never replace a fuse with
Always remember to replace the bor- anything except a fuse with the
rowed fuse. same or a lower amperage rating. A
higher capacity fuse could cause
damage and create a fire hazard.
7 41
Maintenance
✽ NOTICE
• If the power connector is pulled up
from the fuse panel, the warning
chime, audio, clock and interior
lamps, etc., will not operate. The fol-
lowing items must be reset after
replacement.
• Even though the power connector is
pulled up, the battery can still be dis-
charged by operation of the head-
lights or other electrical devices.
HHR4004
Power Connector
Your vehicle is equipped with a power
connector to prevent battery discharge if
your vehicle is parked without being
operated for prolonged periods. Use the
following procedures before parking the
vehicle for prolonged periods.
1. Turn off the engine.

2. Turn off the headlights and tail lights.
3. Open the driver’s side panel cover and
pull up the power connector.
4. Insert the power connector in the
opposite direction.
7 42
Maintenance
FUSE PANEL DESCRIPTION

Engine Compartment ✽ NOTICE
Not all fuse panel descriptions in this
manual may be applicable to your vehi-
cle. It is accurate at the time of printing.
When you inspect the fuse box on your
vehicle, refer to the fuse box label.
OHR077001L
7 43
Maintenance
No. Type Fuse name Fuse rating Circuit Protected

Fuse - C/FAN 30A, BLOWER 40A, FUEL HEATER 30A, ABS1 30A, ABS2 40A,
1 ALT 125A/150A
A/CON 10A
2 GLOW 80A GLOW RELAY UNIT (EURO6), GLOW RELAY (∧EURO6)
3 IG2 40A START RELAY, IGNITION SWITCH
STOP LAMP SWITCH, STOP SIGNAL ELECTRONIC MODULE, STOP SIGNAL
4 STOP LAMP 10A
RELAY
5 TCU 15A TCM, ATM SHIFT LEVER SWITCH
I/P JUNCTION BLOCK (FUSE - H/LAMP LH 15A, H/LAMP RH 15A, HAZARD
6 B+3 40A
LAMP 15A)
I/P JUNCTION BLOCK (FUSE - RR HTD 30A, D/LOCK 15A, P/SEAT 10A,
7 B+1 40A
POWER CONNECTOR (FUSE - MEMORY 15A))
I/P JUNCTION BLOCK (FUSE - FOG LAMP FRT 10A, POWER WINDOW RELAY,
8 E/R B+2 40A
TAIL LAMP RELAY)
JUNCTION
9 BLOCK IG1 40A IGNITION SWITCH
EMS BLOCK (ENGINE CONTROL RELAY, FUSE - ECU1 15A, F/PUMP 15A,
10 ECU 40A
HORN 15A)
11 C/FAN RELAY RELAY. 1 C/FAN 30A
12 START RELAY RELAY. 2 IG2 40A
13 GLOW RELAY RELAY. 3 GLOW 80A (^EURO6)
14 A/CON 10A A/CON RELAY
15 C/FAN 40A C/FAN RELAY
16 BLOWER 40A BLOWER RELAY
17 FUEL HEATER 30A FUEL HEATER RELAY
18 ABS1 30A ABS CONTROL MODULE, ESP CONTROL MODULE
19 ABS2 40A ABS CONTROL MODULE, ESP CONTROL MODULE
7 44
Maintenance
No. Type Fuse name Fuse rating Circuit Protected

I/P JUNCTION BLOCK (FUSE - TCU 15A),
20 B/UP LAMP 10A [A/T] BACK-UP LAMP RELAY, TCM, I/P JUNCTION BLOCK (P/N RELAY)
[M/T] BACK-UP LAMP SWITCH
21 A/CON RELAY RELAY. 4 A/CON 10A
E/R
JUNCTION B/UP LAMP
22 RELAY. 5 [A/T] B/UP-LAMP 10A
BLOCK RELAY
BLOWER
23 RELAY. 6 BLOWER 40A
RELAY
FUEL FILTER
24 RELAY. 7 FUEK HEATER 30A
HEATER RELAY
25 SNSR4 10A IMMOBILIZER MODULE
FUEL PUMP RELAY, PTC HEATER RELAY #1,
26 SNSR3 10A
E/R JUNCTION BLOCK (C/FAN RELAY, A/CON RELAY)
ELECTRONIC EGR ACTUATOR, WGT VACUUM MODULATOR, STOP LAMP
27 SNSR2 10A
SWITCH
28 EMS ECU2 20A ECM
BLOCK
29 SNSR1 15A LAMBDA SENSOR #1/#2, PM SENSOR
30 ECU1 20A ECM
31 HORN 10A HORN RELAY
32 FUEL PUMP 15A FUEL PUMP RELAY
33 ECU1 15A ECM
7 45
Maintenance
Inner Panel
OHR077002L
7 46
Maintenance
No. Fuse name Fuse rating Circuit Protected

TURN LAMP RH, REAR COMBINATION LAMP RH (TAIL LAMP), LICENSE LAMP,
1 TAIL LP RH 10A
JOINT CONNECTOR (JM03 - ILLUMINATIONS)
2 FRT FOG LP 10A FRONT FOG LAMP RELAY
JOINT CONNECTOR (JM02 - POWER WINDOW MAIN SWITCH, PASSENGER POWER
3 FRT P/WDW 25A
WINDOW SWITCH)
JOINT CONNECTOR (JM02 - POWER WINDOW MAIN SWITCH, REAR POWER WINDOW
4 RR P/WDW 25A
SWITCH LH/RH)
5 RR HTD 30A REAR DEFOGGER RELAY
6 TAIL LP LH 10A TURN LAMP LH, REAR COMBINATION LAMP LH (TAIL LAMP), LICENSE LAMP (DUAL)
[A/T] P/N RELAY
7 START 10A
[M/T] E/R JUNCTION BLOCK (START RELAY)
8 ACC 10A JOINT CONNECTOR (JM06 - ETACM, AUDIO, POWER OUTSIDE MIRROR SWITCH)
9 C/LIGHTER 15A CIGAR LIGHTER
10 POWER OUTLET 15A POWER OUTLET
11 SPARE 10A SPARE
12 DOOR LOCK 15A DOOR LOCK/UNLOCK RELAY, DRIVER DOOR LOCK ACTUATOR
13 P/SEAT 10A DRIVER LUMBAR SUPPORT SWITCH
14 A/CON3 10A A/C CONTROL MODULE, BLOWER RESISTOR
15 SPARE 10A SPARE
16 A/CON1 10A A/C CONTROL MODULE
17 WIPER 20A WIPER MOTOR, MULTIFUNCTION SWITCH
18 T/SIG LP 10A HAZARD SWITCH, MULTIFUNCTION SWITCH
E/R JUNCTION BLOCK (JOINT CONNECTOR - FUEL FILTER HEATER RELAY,
19 SNSR1 10A
DIESEL FILTER, GLOW RELAY UNIT, EGR SOLENOID VALVE)
7 47
Maintenance
No. Fuse name Fuse rating Circuit Protected

20 ECU1 10A E/R JUNCTION BLOCK (JOINT CONNECTOR - ECM, AIR FLOW SENSOR)
JOINT CONNECTOR (JM04 - IGNITION KEY HOLE ILL. & DOOR WARNING SWITCH,
ROOM LAMP (FRONT/REAR), DRIVER/PASSENGER DOOR LAMP, AUDIO, ETACM,
21 MEMORY 15A
INSTRUMENT CLUSTER, A/C CONTROL MODULE, DATA LINK CONNECTOR,
TIRE PRESSURE MONITORING MODULE
JOINT CONNECTOR (JM01 - HEAD LAMP (HIGH) RELAY, INSTRUMENT CLUSTER,
22 MODULE2 10A
ETACM, E/R JUNCTION BLOCK (BLOWER RELAY))
23 HTD STRG 15A CLOCK SPRING (STEERING WHEEL HEATER)
ETACM, TIRE PRESSURE MONITORING MODULE, STOP LAMP SWITCH,
VEHICLE SPEED SENSOR, REAR PARKING ASSIST BUZZER,
24 MODULE1 10A AUTO LIGHT & PHOTO SENSOR, STEERING ANGLE SENSOR,
ESP OFF SWITCH, HEAD LAMP LEVELING DEVICE SWITCH,
HEAD LAMP LEVELING DEVICE ACTUATOR LH/RH, ELECTRO CHROMIC MIRROR
E/R JUNCTION BLOCK (FUSE - B/UP LP),
25 TCU1 15A
[A/T] TCM, P/N RELAY
26 A/BAG 15A SRS CONTROL MODULE (IG1)
27 H/LAMP 10A HEAD LAMP (LOW) RELAY
28 RR FOG LP 10A REAR FOG LAMP RELAY
29 CLUSTER 10A INSTRUMENT CLUSTER (IG1)
30 ABS 10A ABS CONTROL MODULE, ESP CONTROL MODULE, DIODE
31 A/BAG IND 10A INSTRUMENT CLUSTER (A/BAG IND.)
32 HTD MIRR 10A REAR DEFOGGER SWITCH, DRIVER/PASSENGER POWER OUTSIDE MIRROR
33 H/LP RH 15A HEAD LAMP RH
34 H/LP LH 15A HEAD LAMP LH
35 HAZARD 15A HAZARD RELAY, FLASHER UNIT, HAZARD SWITCH
7 48
Maintenance
CHECKING THE BATTERY

The fluid in the battery contains a strong Checking the Battery
solution of sulfuric acid, which is poison- Keep the battery clean. Any evidence of
ous and highly corrosive. Be careful not corrosion around the battery posts or ter-
to spill it on yourself or the car. If you do minals should be removed using a solu-
spill battery fluid on yourself, immediate- tion of household baking soda and warm
ly do the following: water. After the battery terminals are dry,
• If battery fluid is on your skin, flush the cover them with a light coating of grease.
affected areas with water for at least 15
minutes and then seek medical assis-
tance. ✽ NOTICE - For batteries marked
• If battery fluid is in your eyes, rinse out
with UPPER and LOWER
your eyes with water and get medical (if equipped)
OHR072011 assistance as soon as possible. While
you are being driven to get medical
WARNING assistance, continue to rinse your eyes
• Batteries can be dangerous! When by using a sponge or soft cloth saturat-
working with batteries, carefully ed with water.
observe the following precautions • If you swallow battery fluid, drink a
to avoid serious injuries. large quantity of water or milk followed
• Do not allow the (+) and (-) by milk of magnesia, eat a raw egg or
jumper cables to touch. It may drink vegetable oil. Get medical assis-
cause sparks. tance as soon as possible.
• The battery may rupture or While batteries are being charged (either
explode when you jump start with by a battery charger or by the vehicle's OHYK07701
a low or frozen battery. alternator), they produce explosive
gases. Always observe these warnings to If your vehicle is equipped with a bat-
prevent injuries from occurring: tery marked with LOWER (MIN) and
CAUTION UPPER (MAX) on the side, you should
• Charge batteries only in a well ventilat-
If you connect unauthorized elec- check the electrolyte level.
ed area.
tronic devices to the battery, the (Continued)
battery may be discharged. Never • Do not permit flames, sparks or smok-
use unauthorized devices. ing in the area.
• Keep children away from the area.
7 49
Maintenance
(Continued)
(Continued)
The electrolyte level should be between WARNING - Battery
LOWER (MIN) and UPPER (MAX). If any electrolyte gets into
dangers
When the electrolyte level is low, add your eyes, flush your eyes
Always read the following with clean water for at least
distilled (or de-mineralized) water. instructions carefully when
(Never add sulfuric acids or other elec- 15 minutes and get immedi-
handling a battery. ate medical attention. If
trolyte).
Be careful not to spill distilled (or dem- Keep lighted cigarettes and possible, continue to apply
ineralized) water over the battery sur- all other flames or sparks water with a sponge or
face or other adjacent components. away from the battery. cloth until medical atten-
Also, do not overfill the battery cells. If tion is received. If elec-
Hydrogen, a highly com- trolyte gets on your skin,
not, it may corrode the battery or other bustible gas, is always
components. Finally, securely close the thoroughly wash the con-
present in battery cells and tacted area.
cell cap. However, we recommend you to may explode if ignited.
contact an authorized HYUNDAI dealer If you feel a pain or a burn-
for better battery service. Keep batteries out of the ing sensation, get medical
reach of children because attention immediately.
batteries contain highly Wear eye protection when
corrosive SULFURIC ACID. charging or working near a
Do not allow battery acid to battery. Always provide
contact your skin, eyes, ventilation when working in
clothing or paint finish. an enclosed space.
(Continued) An inappropriately disposed
battery can be harmful to
the environment and human
health. Dispose the battery
according to your local
law(s) or regulation.
(Continued)
7 50
Maintenance
CHECKING ELECTRIC
■ Example
COOLING FANS
(Continued)
• When lifting a plastic-cased bat-
tery, excessive pressure on the WARNING
case may cause battery acid to The cooling fan is controlled by
leak, resulting in personal injury. engine coolant temperature and
Lift with a battery carrier or with may sometimes operate even when
your hands on opposite corners. the engine is not running. Use
• Never attempt to charge the bat- extreme caution when working near
tery when the battery cables are the blades of the cooling fan, so
connected. that you are not injured by a rotat-
ing fan blade. As the engine
• The electrical ignition system
coolant temperature decreases the
works with high voltage. OJD072039 fan will automatically shut off. This
Never touch these components ❈ The actual battery label in the vehicle is a normal condition.
with the engine running or the may differ from the illustration.
ignition switched on.
Checking Engine Cooling Fan
Battery capacity label
The engine cooling fan should come on
1. CMF60L-BCI : The HYUNDAI model automatically if the engine coolant tem-
name of battery perature is high.
2. 12V : The nominal voltage
3. 60Ah(20HR) : The nominal capacity
Checking Condenser Cooling Fan
(in Ampere hours)
4. 92RC : The nominal reserve capacity When the air conditioning is in operation,
(in min.) the condenser cooling fan comes on
automatically to be controlled by Ecu.
5. 550CCA : The cold-test current in
amperes by SAE
6. 440A : The cold-test current in
amperes by EN
7 51
Maintenance
POWER STEERING FLUID LEVEL

✽ NOTICE Power steering hoses
Grinding noise from the power steering It is suggested that you check the power
pump may be heard immediately after steering hose connections for fluid leak-
the engine is started in extremely cold age at regular intervals. The power steer-
conditions (below - 20°C). If the noise ing hoses should be replaced if there is
stops during warm up, there is no severe surface cracking, scuffing or worn
abnormal function in the system. spots. Deterioration of the hose could
It is due to a power steering fluid char- cause premature failure.
acteristic in extremely cold conditions.
Recommended Fluid
HHR5014
Use PSF-4 type fluid
With the vehicle on level ground, check
the fluid level in the power steering reser- CAUTION
voir periodically. The fluid should be • To avoid damage to the power
between MAX and MIN marks on the steering pump, do not operate the
side of the reservoir at the normal tem- vehicle for prolonged periods
perature. with a low power steering fluid
Before adding power steering fluid, thor- level.
oughly clean the area around the reser- • Never start the engine when the
voir cap to prevent power steering fluid reservoir tank is empty.
contamination. • When adding fluid, be careful that
If the level is low, add fluid to the MAX dirt does not get into the tank.
level. • Too little fluid can result in
increased steering effort and/or
noise from the power steering
system.
• The use of the non-specified fluid
could reduce the effectiveness of
the power steering system and
cause damage to it.
7 52
Maintenance
FUEL FILTER
WARNING
• Do not smoke or have any other
open flame near the vehicle while
bleeding the fuel system.
• Be sure to carefully clean away
any fuel which spilled onto near-
by parts coming out of the air
plug, because such accumula-
tions of fuel might ignite and
cause a fire.
OHR042046 OHR042047
Bleeding the fuel system 2. Pump the hand pump until there are
The fuel system should be bled to no more bubbles in the fuel coming
remove air as described in the illustration out of the air plug. When doing this,
if the fuel supply is exhausted during place a cloth around the air plug to
travel, when the fuel filter is replaced, or prevent the escaping fuel from spew-
if the vehicle is not used for a long time. ing about.
3. Tighten the air plug when there are no
more bubbles in the fuel.
1. Loosen the air plug at the upper part
of the fuel filter. 4. Continue pumping until the hand
pump becomes stiff.
5. Finally, check to be sure that there is
✽ NOTICE no leakage of fuel.
The fuel filter is located on the frame If in doubt, we recommend that you
under the driver's side. consult an authorized HYUNDAI dealer.
7 53
Maintenance
✽ NOTICE
We recommend that the accumulated
water in the fuel filter be removed by an
authorized HYUNDAI dealer.
WARNING
• Do not smoke or have any other
open flame near the vehicle while
bleeding the fuel system.
• Be sure to carefully wipe away
any water drained out in this
OHR042048 OHR042047 manner, because the fuel mixed
Removal of water from the fuel fil- 2. Operate the hand pump slowly 6 or 7 in the water might be ignited and
ter times in order to force the water out result in a fire.
If the fuel filter warning light illuminates through the drain plug.
during driving, it indicates that water has 3. Tighten the drain plug when water no
accumulated in the fuel filter. If this longer comes out.
occurs, remove the water as described 4. Loosen the air plug and bleed the air.
below. (Refer to "Bleeding the fuel system")
5. Check to be sure that the warning light
1. Loosen the drain plug at the bottom of illuminates when the ignition key is
the fuel filter. turned to "ON", and that it goes off
when the engine is started.
If in doubt, we recommend that you
consult an authorized HYUNDAI dealer.
7 54
Maintenance
HEADLIGHT AIMING ADJUSTMENT

Before performing aiming adjustment, Vertical line
make sure of the following. 30mm (1.18 in.)
Horizontal line W
Vertical aiming “P”
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and
press the front bumper and rear H
bumper down several times. Place the Cut-off line
vehicle at a distance of 3,000 mm
(118 in.) from the test wall. L
Horizontal H Ground
3. See that the vehicle is unloaded line
aiming
(except for full levels of coolant,
OHR072106L G290B01HR-1
engine oil and fuel, and spare tire,
■ Front view
jack, and tools). 7. Adjust each cut-off line of the low
4. Clean the head lights lens and turn on beam to the parallel line with a phillips Horizontal line 30mm (1.18 in.)
the headlight (low beam). screwdriver - VERTICAL AIMING.
5. Open the hood. 8. Adjust each cut-off line of the low Vertical line “P”
6. Draw the vertical line (through the beam to each vertical line with a
center of each headlight beam pat- phillips screwdriver - HORIZONTAL
tern) and the horizontal line (through AIMING.
the center of each headlight beam H
Cut-off line
pattern) on the aiming screen.
And then, draw a horizontal parallel W
line at 30 mm (1.18 in.) under the hor-
izontal line. Ground line
G290B02HR-1
Adjustment After Headlight

Assembly Replacement
7 55
Maintenance
REPLACEMENT OF LIGHT BULBS

If the vehicle has had front body repair Before attempting to replace a light bulb, Headlight Bulb
and the headlight assembly has been be sure the switch is turned to the "OFF" 1. Allow the bulb to cool. Wear eye pro-
replaced, an headlight aiming should be position. tection.
checked using an aiming screen as The next paragraph shows how to reach 2. Always grasp the bulb by its terminal
shown in the illustration. Turn on the the light bulbs so they may be changed. plate base, avoid touching the glass.
headlight switch. (Low Beam Position) Be sure to replace the burned-out bulb
with one of the same number and
1. Adjust headlights so that main axis of wattage rating.
light is parallel to center line of the
body and is aligned with point "P" CAUTION
shown in the illustration.
• Keep the lamps out of contact
2. Dotted lines in the illustration show the with petroleum products, such as
center of headlights. oil, gasoline, etc.
• After heavy, driving rain or wash-
SPECIFICATIONS: ing, headlight and taillight lenses
"H" could appear frosty. This condi-
Horizontal center line of headlights tion is caused by the temperature
from ground. difference between the lamp
Low Deck: 815 mm (32.1 in.) inside and outside. This is similar G270A02HR
High Deck: 820 mm (32.3 in.) to the condensation on your win-
dows inside your vehicle during 3. Open the door and remove a head-
the rain and doesn’t indicate a light assembly mounting screw with a
"W" problem with your vehicle. If the philips screwdriver.
Distance between each headlight cen- water leaks into the lamp bulb cir-
ter : 1,330 mm (52.4 in.) cuitry, we recommend that the
system be checked by an author-
"L" ized HYUNDAI dealer.
Distance between the headlights and
the wall that the lights are tested
against.
: 3,000 mm (118 in.)
7 56
Maintenance
OHR072029 HHR5031 HHR5033

4. Open the hood and remove a head- 6. Remove the dust cover. 8. Remove the protective cap from the
light assembly mounting bolt with a replacement bulb and install the new
spanner. bulb by matching the plastic base with
the headlight hole. Reattach the bulb
spring and install the dust cover.
Reconnect the power cord.
9. Use the protective cap and carton to
dispose of the old bulb.
10.Check for proper headlight aim.
✽ NOTICE
We recommend that the headlight aim-
ing be adjusted after an accident or after
HHR5032 the headlight assembly is reinstalled at a
7. Push the bulb spring to remove the authorized HYUNDAI dealer.
OHR052030
headlight bulb.
5. Disconnect the power cord from the
bulb base in the back of the headlight.
7 57
Maintenance
G270A03O G270A02HR OHR072029

Front Turn Signal light / Position 2. Open the hood and remove a head-
Light light assembly mounting bolt with a
WARNING spanner.
The halogen bulb contains gas 1. Open the door and remove a headlight
under pressure and if impacted assembly mounting screw with a
could shatter, resulting in flying philips screwdriver.
fragments. Always wear eye protec-
tion when servicing the bulb.
Protect the bulb against abrasions
or scratches and against liquids
when lighted. Turn the bulb on only
when installed in a headlight.
Replace the headlight if damaged
or cracked. Keep the bulb out of the
reach of children and dispose of
the used bulb with care.
OHR052034
3. Disconnect the power cord from the
bulb.
7 58
Maintenance
HHR5035 G270D01HR G270D02HR

4. To replace the front turn signal light (1) Rear Combination Light 2. Remove the cover by pressing the
or position light (2), take it out from the 1. Disconnect the power cord from the both sides of the cover.
bulb holder by turning it counterclock- bulb.
wise.
5. Install the new bulb.
7 59
Maintenance
HHR5038 OHR052100 OHR052101

3. To replace the rear combination light License Plate Light 2. Take the bulb out from the bulb holder
(stop/tail light, turn signal light or back- 1. Remove the mounting screws of the by turning it counterclockwise and dis-
up light), take it out from the bulb hold- license plate light with a phillips screw- connect the power code.
er by turning it counterclockwise. driver. 3. Install the new bulb.
(1) Turn Signal Light
(2) Stop/Tail Light
(3) Back-up Light
4. Install the new bulb.
7 60
Maintenance
G270E01HR G270E02HR G270F02HR

Side Repeater 2. Disconnect the power code. Rear Fog Light (if equipped)
1. Push the cover toward the front of 1. Remove the cover by pressing the
vehicle and remove it. both sides of the cover.
G270E03HR
3. Replace with a new bulb.
7 61
Maintenance
G270F03HR HHR5039 G270H01HR

2. Take the bulb out from the bulb holder Map Light (if equipped, Interior Light (if equipped,
by turning it counterclockwise. With Spectacle Case) Without Spectacle Case)
3. Replace with a new bulb. (21 W) 1. Remove the cover with a flat-head 1. Remove the cover with a flat-head
screwdriver. screwdriver.
G270G02HR G270H02HR
2. Replace with a new bulb. 2. Replace with a new bulb.
7 62
Maintenance
BULB WATTAGES
OHR072108L
No. Part Name Bulb Type Wattage (W) No. Part Name Bulb Type Wattage (W)
1 Front Fog Light (if equipped) H8 35 Interior Light (if equipped, FESTOON
7 10
2 Front Position Light W5W 5 Without Spectacle Case) 10W
3 Headlight (High/Low) H4 60/55 Turn Signal

8 P21W 21
4 Front Turn Signal Light P21W 21 Light
Rear Combination
5 Side Repeater (if equipped) W5W 5 9 Light Stop/Tail Light P21/5W 21/5
Map Light 10 Back-up Light W16W 16

6 W10W 10
(if equipped, With Spectacle Case) 11 License Plate Light W5W 5
7 63
Maintenance
EMISSION CONTROL SYSTEM (IF EQUIPPED)

Your HYUNDAI is equipped with an emis- Vehicle modifications Catalytic converter (if equipped)
sion control system to meet all require- This vehicle should not be modified.
ments of the Emission prohibition rules of Modification of your vehicle could affect
your province. its performance, safety or durability and WARNING
In order to assure the proper function of may even violate governmental safety The exhaust system and catalytic
the emission control systems, we recom- and emissions regulations. system are very hot while the
mend that the system be serviced by an In addition, damage or performance engine is running or immediately
authorized HYUNDAI dealer in accor- problems resulting from any modification after the engine is turned off. Keep
dance with the maintenance schedule in may not be covered under warranty. away from the exhaust system and
this chapter. catalytic, you may get burned.
• If you use unauthorized electronic
devices, it may cause the vehicle to Also, do not remove the heat sink
Exhaust emission control system operate abnormally, wire damage, bat- around the exhaust system, do not
The Exhaust Emission Control System is tery discharge or fire. For your safety, seal the bottom of the vehicle or do
a highly effective system which controls do not use unauthorized electronic not coat the vehicle for corrosion
exhaust emissions while maintaining devices. control. It may present a fire risk
good vehicle performance. under certain conditions.
7 64
Maintenance
(Continued)
WARNING
• Do not touch the catalytic con-
• Use diesel only. verter or any other part of the
• Maintain the engine in good oper- exhaust system while the catalyt-
ating condition. Extremely high ic converter is hot. Shut off the
catalytic converter temperatures engine, wait for at least one hour
can result from improper opera- before touching the catalytic con-
tion of the electrical, ignition or verter or any other part of the
electronic fuel injection. exhaust system.
• If your engine stalls, pings, or is • Remember that your HYUNDAI
hard to start, have your HYUNDAI dealer is your best source of
dealer inspect and repair the assistance.
Catalytic Converter OHR072107L problem as soon as possible. • Do not park, idle or drive your
HYUNDAI vehicle is equipped with oxida- • Avoid driving with a very low fuel vehicle over any combustible
tion type catalytic converter to reduce the level. Running out of diesel may material such as grass, paper,
carbon monoxide, hydrocarbons and par- cause the engine to stop and leaves or rags. These materials
ticulates contained in the exhaust gas. result in damage to the catalytic might contact the hot catalytic
converter. converter and a fire might result.
• Avoid idling the engine for peri-
ods longer than 10 minutes.
• The vehicle should not be
pushed or pulled to get started.
This may cause the catalytic con-
verter to overheat and create a
fire hazard.
(Continued)
7 65
Maintenance
Diesel Particulate Filter If the malfunction indicator light contin- Type B

(if equipped) ues to be blinked in spite of the proce- The Diesel Particulate Filter (DPF) sys-
Type A dure, we recommend that the DPF system removes the soot in the exhaust gas.
tem be checked by an authorized Unlike a disposable air filter, the DPF
The Diesel Particulate Filter (DPF) sys- HYUNDAI dealer.
tem removes the soot emitted from the system automatically burns (oxidizes)
vehicle. If you continue to drive with the malfunc- and removes the accumulated soot
tion indicator light blinking for a long time, according to the driving condition. In
Unlike a disposable air filter, the DPF the DPF system can be damaged and
system automatically burns (oxidizes) other words, the active burning by engine
fuel consumption can be worsen. control system and high exhaust gas
and removes the accumulated soot
according to the driving condition. In temperature caused by normal/high driv-
other words, the active burning by engine CAUTION - Diesel Fuel ing condition burns and removes the
control system and high exhaust gas accumulated soot.
(if equipped with DPF)
temperature caused by normal/high driv- However, if the vehicle continues to be
It is recommended to use the regu-
ing condition burns and removes the driven at repeated short distance or driv-
lated automotive diesel fuel for
accumulated soot. en at low speed for a long time, the accu-
diesel vehicle equipped with the
However, if the vehicle continues to be mulate soot may not be automatically
DPF system.
driven at low speed for long time, the removed because of low exhaust gas
If you use diesel fuel including high temperature. More than a certain amount
accumulated soot may not be automati- sulfur (more than 50 ppm sulfur)
cally removed because of low exhaust of soot deposited, the malfunction indica-
and unspecified additives, it can tor light ( ) illuminates.
gas temperature. In this particular case, cause the DPF system to be dam-
the amount of soot is out of detection When the malfunction indicator light
aged and white smoke can be emit-
limit, the soot oxidation process by blinks, it may stop blinking by driving the
ted.
engine control system may not happen vehicle at more than 60km/h (37 mph) or
and the malfunction indicator light may at more than second gear with 1500 ~
blink. 2500 engine rpm for a certain time (for
When the malfunction indicator light about 25 minutes).
blinks, it may stop blinking by driving the
vehicle at more than 60 km/h (37 mph) or
at more than second gear with 1500 ~
2000 engine rpm for a certain time (for
about 25 minutes).
7 66
Maintenance
If the malfunction indicator light ( ) EGR system (if equipped)

continues to be blinked or the warning This system helps control oxides of nitro-
massage "check exhaust system" illumi- gen by recirculating a part of the exhaust
nates in spite of the procedure, please gas into the engine, there by reducing
visit an authorized HYUNDAI dealer and cylinder combustion temperature.
the check the DPF system. The EGR system helps reduce Nox
If you continue to drive with the malfunc- (Oxides of Nitrogen) emission gasses.
tion indicator light blinking for a long
time, the DPF system can be damaged
and fuel consumption can be worsen.
CAUTION - Diesel Fuel

(if equipped with DPF)
It is recommended to use the regu-
lated automotive diesel fuel for
diesel vehicle equipped with the
DPF system.
If you use diesel fuel including high
sulfur (more than 50 ppm sulfur) and
unspecified additives, it can cause
the DPF system to be damaged and
white smoke can be emitted.
7 67
Maintenance
APPEARANCE CARE
Engine Compartment (Continued) Exterior care
The following should be checked regularly: • When checking the engine room, The following should be checked
• Engine oil level and condition do not go near fire. Fuel, washer monthly:
• Transmission fluid level and condition fluid, etc. are flammable oils that • Overall appearance and condition
• Brake fluid level may cause fire. • Wheel condition and wheel nut torque
• Engine coolant level • Before touching the battery, igni- • Exhaust system condition
• Windshield washer fluid level tion cables and electrical wiring, • Light condition and operation
• Accessory drive belt condition you should disconnect the bat- • Windshield glass condition
tery "-" terminal. You may get an • Wiper blade condition
• Engine coolant hose condition electric shock from the electric
• Fluid leaks (on or below components) current. • Paint condition and body corrosion
• Power steering fluid level • When you remove the interior • Fluid leaks
• Battery condition trim cover with a flat bed (-) driv- • Door and hood lock condition
• Air filter condition er, be careful not to damage the • Tire pressure and condition
cover. (including spare tire)
• Be careful when you replace and
CAUTION clean bulbs to avoid burns or Protecting Your HYUNDAI from
• Do not put heavy objects or apply electrical shock. Corrosion:
excessive force on top of the By using the most advanced design and
engine cover (if equipped) or fuel construction practices to combat corro-
related parts. sion, HYUNDAI produces cars of the
• When you inspect the fuel system highest quality. However, this is only part
(fuel lines and fuel injection of the job. To achieve the long-term cor-
devices), we recommend that you rosion resistance your HYUNDAI can
contact an authorized HYUNDAI deliver, the owner's cooperation and
dealer. assistance is also required.
• Do not drive long time with the
engine cover (if equipped) removed.
(Continued)
7 68
Maintenance
Common Causes of Corrosion Moisture Breeds Corrosion Washing and waxing

The most common causes of corrosion Moisture creates the conditions in which High-pressure washing
on your car are: corrosion is most likely to occur. For • When using high-pressure washers,
• Road salt, dirt and moisture that is example, corrosion is accelerated by make sure to maintain sufficient dis-
allowed to accumulate underneath the high humidity, particularly when tempera- tance from the vehicle.
car. tures are just above freezing. In such
Insufficient clearance or excessive
• Removal of paint or protective coatings conditions, the corrosive material is kept
pressure can lead to component dam-
by stones, gravel, abrasion or minor in contact with the car surfaces by mois-
age or water penetration.
scrapes and dents which leave unpro- ture that is slow to evaporate.
• Do not spray the camera, sensors or its
tected metal exposed to corrosion. Mud is particularly corrosive because it is
surrounding area directly with a high
slow to dry and holds moisture in contact
pressure washer. Shock applied from
with the vehicle. Although the mud
High-Corrosion Areas high pressure water may cause the
appears to be dry, it can still retain the
If you live in an area where your car is device to not operate normally.
moisture and promote corrosion.
regularly exposed to corrosive materials, • Do not bring the nozzle tip close to
High temperatures can also accelerate
corrosion protection is particularly impor- boots (rubber or plastic covers) or con-
corrosion of parts that are not properly
tant. Some of the common causes of nectors as they may be damaged if
ventilated so the moisture can be dis-
accelerated corrosion are road salts, they come into contact with high pres-
persed. For all these reasons, it is partic-
dust control chemicals, ocean air and sure water.
ularly important to keep your car clean
industrial pollution. and free of mud or accumulations of
other materials. This applies not only to
the visible surfaces but particularly to the
underside of the car.
7 69
Maintenance
Washing Your HYUNDAI Use a clean sponge or cloth, rinse it fre-

Never wash your car when the surface is quently and don't damage the finish by CAUTION
hot from being in the sun. Always wash rubbing too hard. For stubborn spots,
your car in the shade. dampen them frequently and remove
Wash your car frequently. Dirt is abrasive them a little at a time.
and can scratch the paint if it is not To clean whitewall tires, use a stiff brush
removed. Air pollution or acid rain may or soapy steel-wool scouring pad.
damage the paint and trim through To clean plastic wheel covers, use a
chemical action if pollutants are allowed clean sponge or soft cloth and water.
to remain in contact with the surface. If
you live near the ocean or in an area If you find any nicks or scratches in the
where road salts or dust control chemi- paint, use touch-up paint to cover them
cals are used, you should pay particular to prevent corrosion. To protect the paint-
attention to the underside of the car. Start work of the car against corrosion, you OJB037800
by rinsing the car to remove dust and must clean your HYUNDAI (at least once
loose dirt. In winter, or if you have driven • Water washing in the engine com-
a month). Give special attention to the
through mud or muddy water, be sure to partment including high pressure
removal of salt, mud and other sub-
thoroughly clean the underside as well. water washing may cause the fail-
stances on the underside of the splash-
Use a hard direct stream of water to ure of electrical circuits located in
boards of the car. Make sure that the out-
remove accumulations of mud or corro- the engine compartment.
lets and the underside of the doors are
sive materials. open. Paint damage can be caused by • Never allow water or other liquids
Use a good quality car-washing solution small accumulation of tar, industrial pre- to come in contact with electri-
and follow the manufacturer's directions cipitation, tree resin, insects and bird cal/electronic components inside
on the package. These are available at droppings, when not removed immedi- the vehicle as this may damage
your HYUNDAI dealer or auto parts out- ately. If water alone is not strong enough them.
let. Don't use strong household deter- to remove the accumulated dirt, use a (Continued)
gents, gasoline, strong solvents or abra- mild car washing solution. Be sure to
sive cleaning powders as these may rinse the surface after washing to remove
damage the finish. the solution. Never allow the solution to
dry on the painted surfaces.
7 70
Maintenance
Polishing and Waxing Maintaining Bumpers

(Continued)
Always wash and dry the car before pol- Special precautions must be observed to
• Be careful when washing the side
ishing or waxing or using a combination preserve the appearance of the bumpers
windows of your vehicle.
cleaner and wax. Use a good quality on your HYUNDAI. They are:
Especially, with high-pressure
commercial product and follow the man- • Be careful not to spill battery elec-
water, water may leak through the
ufacturer's directions on the container. trolyte or hydraulic brake fluid on the
windows and wet the interior.
Polish and wax the bright trim pieces as bumpers. If you do, wash it off immedi-
• To prevent damage to the plastic well as the paint. ately with clear water.
parts and lamps, do not clean
with chemical solvents or strong • Be gentle when cleaning the bumper
detergents. When to Wax Again surfaces. They are made of soft plastic
You should polish and wax the car again and the surface can be damaged if
when water no longer beads on a clean mistreated. Do not use abrasive clean-
surface but spreads out over a larger ers. Use warm water and mild soap or
Spot Cleaning car-washing solution.
area.
Don't use gasoline, strong solvents or • Do not expose the bumpers to high
corrosive cleaning agents. These can temperatures. For example, if you have
damage the finish of the car. To remove your car repainted, do not leave the
road tar, use turpentine on a clean, soft bumpers on the car if the car is going
cloth or commercially available bug and to be placed in a high-temperature
tar remover. Be gentle. paint booth.
To remove dead insects or tree sap, use
warm water and mild soap or car-wash-
ing solution. Soak the spot and rub gen-
tly. If the paint has lost its luster, use a
commercial car-cleaning polish.
7 71
Maintenance
Interior care Cleaning the upholstery and interior Leather (if equipped)
Interior general precautions trim • Feature of Seat Leather
Prevent caustic solutions such as per- Vinyl (if equipped) - Leather is made from the outer skin
fume and cosmetic oil, from contacting Remove dust and loose dirt from vinyl of an animal, which goes through a
the interior parts because they may with a whisk broom or vacuum cleaner. special process to be available for
cause damage or discoloration. If they do Clean vinyl surfaces with a vinyl cleaner. use. Since it is a natural object, each
contact the interior parts, wipe them off part differs in thickness or density.
immediately. See the instructions for the Fabric (if equipped) Wrinkles may appear as a natural
proper way to clean vinyl. Remove dust and loose dirt from fabric result of stretching and shrinking
with a whisk broom or vacuum cleaner. depending on the temperature and
Clean with a mild soap solution recom- humidity.
CAUTION mended for upholstery or carpets. - The seat is made of stretchable fabric
• Never allow water or other liquids Remove fresh spots immediately with a to improve comfort.
to come in contact with electri- fabric spot cleaner. If fresh spots do not - The parts contacting the body are
cal/electronic components inside receive immediate attention, the fabric curved and the side supporting area
the vehicle as this may damage can be stained and its color can be is high which provides driving comfort
them. affected. Also, its fire-resistant properties and stability.
• When cleaning leather products can be reduced if the material is not - Wrinkles may appear naturally from
(steering wheel, seats etc.), use properly maintained. usage. It is not a fault of the products.
neutral detergents or low alcohol
content solutions. If you use high
alcohol content solutions or acid/ CAUTION
alkaline detergents, the color of Using anything but recommended
the leather may fade or the sur- cleaners and procedures may affect
face may get stripped off. the fabric’s appearance and fire-
resistant properties.
7 72
Maintenance
- Light colored (beige, cream beige) Cleaning the seat belt webbing
CAUTION leather is easily contaminated and Clean the belt webbing with any mild
• Wrinkles or abrasions which the stain is noticeable. Clean the soap solution recommended for cleaning
appear naturally from usage are seats frequently. upholstery or carpet. Follow the instruc-
not covered by warranty. - Avoid wiping with wet cloth. It may tions provided with the soap. Do not
• Belts with metallic accessories, cause the surface to crack. bleach or re-dye the webbing because
zippers or keys inside the back this may weaken the seat belt.
pocket may damage the seat fab- • Cleaning the leather seats
ric. Cleaning the interior window glass
- Remove all contaminations instantly.
• Make sure not to wet the seat. It Refer to instructions below for If the interior glass surfaces of the vehi-
may change the nature of natural removal of each contaminant. cle become fogged (that is, covered with
leather. an oily, greasy or waxy film), they should
- Cosmetic products (sunscreen, foun-
• Jeans or clothes which could dation, etc.) be cleaned with glass cleaner. Follow the
bleach may contaminate the sur- directions on the glass cleaner container.
face of the seat covering fabric. Apply cleansing cream on a cloth and
wipe the contaminate spot. Wipe off
the cream with a wet cloth and
• Caring for the leather seats remove water with a dry cloth.
- Vacuum the seat periodically to - Beverages (coffee, soft drink, etc.)
remove dust and sand on the seat. It Apply a small amount of neutral
will prevent abrasion or damage of detergent and wipe until contamina-
the leather and maintain its quality. tions do not smear.
- Wipe the natural leather seat cover - Oil
often with dry or soft cloth. Remove oil instantly with absorbable
- Use of proper leather protective may cloth and wipe with stain remover
prevent abrasion of the cover and used only for natural leather.
helps maintain the color. Be sure to - Chewing gum
read the instructions and consult a Harden the gum with ice and remove
specialist when using leather coating gradually.
or protective agent.
7 73
Maintenance
To help prevent corrosion • When cleaning lower door panels, Don't Neglect the Interior
You can help prevent corrosion from get- rocker panels and frame members, be Moisture can collect under the floor mats
ting started by observing the following: sure that drain holes are kept open so and carpeting to cause corrosion. Check
that moisture can escape and not be under the mats periodically to be sure
trapped inside to ac-celerate corrosion. the carpeting is dry. Use particular care if
Keep Your Car Clean
you carry fertilizers, cleaning materials or
The best way to prevent corrosion is to chemicals in the car.
keep your car clean and free of corrosive Keep Your Garage Dry
materials. Attention to the underside of Don't park your car in a damp, poorly These should be carried only in proper
the car is particularly important. ventilated garage. This creates a favor- containers and any spills or leaks should
able environment for corrosion. This is be cleaned up, flushed with clear water
• If you live in a high-corrosion area — and thoroughly dried.
where road salts are used, near the particularly true if you wash your car in
ocean, areas with industrial pollution, the garage or drive it into the garage
acid rain, etc.—, you should take extra when it is still wet or covered with snow,
care to prevent corrosion. In winter, ice or mud. Even a heated garage can
hose off the underside of your car at contribute to corrosion unless it is well
least once a month and be sure to ventilated so moisture is dispersed.
clean the underside thoroughly when
winter is over. Keep Paint and Trim in Good
• When cleaning underneath the car, Condition
give particular attention to the compo- Scratches or chips in the finish should be
nents under the fenders and other covered with "touch-up" paint as soon as
areas that are hidden from view. Do a possible to reduce the possibility of cor-
thorough job; just dampening the accu- rosion. If bare metal is showing through,
mulated mud rather than wash ing it the attention of a qualified body and paint
away will accelerate corrosion rather shop is recommended.
than prevent it. Water under high pres-
sure and steam are particularly effec-
tive in removing accumulated mud and
corrosive materials.
7 74
Vehicle identification number (VIN) / 8-2
Engine number / 8-2
Declaration of conformity / 8-3
Consumer information 8
Consumer information
VEHICLE IDENTIFICATION NUMBER (VIN) ENGINE NUMBER

■ 2.5L
OHR062007
■ 2.6L
OHR062002L OHR062001
The vehicle identification number (VIN) is The vehicle identification number is
the number used in registering your car stamped as shown in the illustration.
and in all legal matters pertaining to its Please use this number when ordering
ownership, etc. replacement parts.
It can be found on the identification plate
attached on the driver's side of the cen-
ter pillar outer panel.
I010B01HR
The engine number is stamped on the
engine block as shown in the drawing.
8 2
Consumer information
DECLARATION OF CONFORMITY
■ Example
CE0678
The radio frequency components of the
vehicle comply with requirements and
other relevant provisions of Directive
1995/5/EC.
Further information including the manu-
facturer's declaration of conformity is
available on HYUNDAI web site as fol-
lows;
http://service.hyundai-motor.com
8 3
Measurement / 9-2
Tire / 9-2
Fuel system / 9-2
Tire load and speed capacity / 9-3
Engine / 9-3
Lubrication chart / 9-4
Specifications 9
Specifications
MEASUREMENT
mm
Long Wheel Base Extra Long Wheel Base
Item Low Deck High Deck Low Deck
Standard Cab Double Cab Cab Standard Cab Standard Cab
Overall Length 4,850 4,810 4,850 5,175
Overall Width 1,740 ← ← 1,740
Overall Height 1,970 ← ← ←
Wheel Base 2,430 ← ← 2,640
Front 1,485 ← ← 1,485
Wheel Tread
Rear 1,320 ← 1,420 1,320
TIRE
Tire Size
Item
Low Deck High Deck
Front 195/70R15C-8PR ←
Standard
Rear 145R13C-8PR 195/70R15C-8PR
Front Full size 1EA −
Spare
Rear Full size 1EA Full size 1EA
FUEL SYSTEM
Liter Imp.gal
Fuel tank Capacity
65 14.3
9 2
Specifications
TIRE LOAD AND SPEED CAPACITY

Load Capacity Speed Capacity
Item Tire size Wheel size
LI * 1
kg SS *2 km/h
195/70R15C-8PR (Low Deck) 5.5JX15 104 900 R 170
Full size tire 145R13C-8PR (Low Deck) 4.0JX13 86 530 R 170
195/70R15C-8PR (High Deck) 6.0JX15 104 900 R 170
*1 LI : LOAD INDEX
*2 SS : SPEED SYMBOL
ENGINE
Diesel engine
Item
2.5L engine 2.6L engine
Engine Type D4CB D4BB
Bore × Stroke(mm) 91 × 96 91.1X100
Total displacement(cc) 2,497 2,607
Firing order 1-3-4-2 1-3-4-2
9 3
Specifications
LUBRICATION CHART
Items Recommended in field Quantity (liter)
Engine oil (diesel) ACEA
Recommends DPF Engine Oil : 7.4
C2
2.5L Engine at Oil Pan : 6.6
Non ACEA -15°C ABOVE : SAE 15W-40 at Oil Filter : 0.8
DPF A3/B4 -20°C ABOVE : SAE 10W-30/40
-25°C ABOVE : SAE 5W-30/40
30°C BELOW : SAE 0W-30/40 Engine Oil : 5.7
API CF-4 above,
2.6L Engine at Oil Pan : 5.1
ACEA A3/B3
at Oil Filter : 0.6
2.5L Engine HK MTF(SK), HD MTF(SHEEL) 2.2~2.3

Manual transmission oil
2.6L Engine HYUNDAI GENUINE PARTS MTF 75W/85 (API GL-4) 234~2.5
Power steering oil PSF-3 0.8
Coolant High quality ethylene glycol base for aluminum radiator 8
Brake fluid DOT 3, DOT 4 or equivalent As required
SAE J310a,
Front, rear wheel bearing As required
MULTI-PURPOSE GREASE NLGI-2 or equivalent
SAE 90 (-30°C ~ 30°C)
API GL-4
Rear axle oil SAE 140 (ABOVE 30°C) 1.6
API GL-5 SAE 80 (BELOW -30°C)
9 4
Index I
Index
Audio (without touch screen) ..........................................4-5
A Feature of your audio ...................................................4-6
Air bag - supplemental restraint system ........................3-26 Media..........................................................................4-10
Additional safety precautions.....................................3-39 Radio ............................................................................4-9
Air bag warning label.................................................3-40 Setup ...........................................................................4-19
Air bag warning light .................................................3-29
Do not install a child restraint on the B
front passenger's seat.................................................3-28
Before starting the engine................................................5-3
Driver's and passenger's front air bag ........................3-31
Before you start the engine, you should always: .........5-3
How does the air bag system operate ........................3-27
To start the engine ........................................................5-4
SRS care .....................................................................3-38
Bulb wattages.................................................................7-63
SRS components and functions..................................3-29
Why didn't my air bag go off in a collision? .............3-34
C
Air conditioning care .....................................................7-29
Checking the air conditioning operation....................7-29 Center seatback console compartment .........................3-69
Checking the climate control air filter Coin holder .................................................................3-69
(for evaporator and blower unit) ..............................7-30 Multi tray....................................................................3-69
Keeping the condenser clean......................................7-29 Changing a flat tire ........................................................6-10
Lubrication .................................................................7-29 After changing wheels................................................6-16
Appearance care.............................................................7-68 Wheel cover ...............................................................6-10
Engine compartment ..................................................7-68 Changing the air cleaner filter .......................................7-23
Exterior care ...............................................................7-68 Changing the oil and filter.............................................7-18
Interior care ................................................................7-72 Checking and changing the engine coolant...................7-20
To help prevent corrosion...........................................7-74 Recommended engine coolant ...................................7-20
Washing and waxing ..................................................7-70
Ashtray...........................................................................3-64
I 2
Index
Checking and replacing fuses ........................................7-40 Child restraint system ....................................................3-22
Power connector .........................................................7-42 Installation on front seat center position....................3-24
Replacing a fusible link..............................................7-40 Installation on outboard front passenger's seat ..........3-24
Replacing accessory fuse ...........................................7-40 Cigarette lighter .............................................................3-63
Checking drive belts ......................................................7-31
Checking electric cooling fans ......................................7-51 D
Checking the battery......................................................7-49 Day/night inside rearview mirror ..................................3-71
Checking the battery ..................................................7-50 Declaration of conformity ...............................................8-3
Checking the brakes ...................................................7-28 Digital clock...................................................................3-63
Adding brake fluid .....................................................7-29 Door locks........................................................................3-7
Checking the brake fluid level ...................................7-28 Central door lock .........................................................3-8
Recommended brake fluid .........................................7-28 Locking and unlocking front doors with a key ............3-7
To check the fluid level ..............................................7-28 Locking from the inside ...............................................3-8
Checking the engine oil .................................................7-16 Locking from the outside .............................................3-7
Adding oil...................................................................7-17 Drink holder...................................................................3-65
Engine oil consumption..............................................7-18 Driving for economy......................................................5-22
Recommended Oil......................................................7-16
Checking the free-play...................................................7-30
Brake pedal.................................................................7-31
Clutch pedal................................................................7-31
Steering wheel ............................................................7-30
Checking the rear axle oil..............................................7-26
To check the rear axle oil level ..................................7-27
Checking the transmission oil (manual) ........................7-26
I 3
Index
Fuel filter........................................................................7-53
E Bleeding the fuel system ............................................7-53
Emergency commodity ..................................................6-17 Removal of water from the fuel filter ........................7-54
Fire extinguisher ........................................................6-17 Fuel requirements ............................................................1-2
First aid kit .................................................................6-17 Use diesel .....................................................................1-2
Tire pressure gauge ...................................................6-18 Fuel system ......................................................................9-2
Triangle reflector ........................................................6-17 Fuel tank cap..................................................................3-73
Emission control system................................................7-64 Fuse panel description ...................................................7-43
Catalytic converter ....................................................7-64 Engine compartment .................................................7-43
Diesel particulate filter ..............................................7-66 Inner panel..................................................................7-46
EGR system ...............................................................7-67
Exhaust emission control system ...............................7-64 G
Vehicle modifications ...............................................7-64 Glove box.......................................................................3-67
Engine ..............................................................................9-3 Pen, card and tissue holder.........................................3-68
Engine compartment ................................................2-4, 7-4
Engine ilde rpm adjustment knob..................................3-64 H
Engine number.................................................................8-2
Explanation of scheduled maintenance items ...............7-13 Hazard warning system .................................................3-61
Exterior tool box............................................................3-76 Headlight aiming adjustment.........................................7-55
Headlight leveling device system ..................................3-61
F Higher speed motoring ..................................................5-26
Pre-trip inspections.....................................................5-26
Filling the washer reservoir ...........................................7-25 Hood release ..................................................................3-72
Front open service panel..................................................7-3 Closing the hood ........................................................3-72
How to use this manual ...................................................1-2
I 4
Index
I K
If the engine overheats.....................................................6-6 Key positions ...................................................................5-4
If the engine will not start ...............................................6-3 Keys .................................................................................3-3
If engine doesn't turn over or turns over slowly ..........6-3 Immobilizer system .....................................................3-4
If engine turns over normally but does not start ..........6-3 Record your key number ..............................................3-3
If the engine stalls at a crossroad or crossing ..............6-4
If the engine stalls while driving..................................6-3 L
If you have a flat tire .......................................................6-9 Lighting..........................................................................3-54
If you lose your keys .....................................................6-20 Battery saver function ...............................................3-54
If your vehicle must be towed .......................................6-18 Lighting control..........................................................3-54
Emergency towing......................................................6-19 Locking differential .......................................................5-21
Towing the vehicle .....................................................6-18 Lubrication chart..............................................................9-4
Instrument cluster ..........................................................3-41
Gauges ........................................................................3-42 M
Warning and indicator lights ......................................3-47
Warning light operation..............................................3-50 Maintenance intervals ......................................................7-6
Interior light ...................................................................3-65 A few tips .....................................................................7-7
Interior light (without spectacle case)........................3-64 Do-it-yourself maintenance..........................................7-7
Map light (with spectacle case)..................................3-64 General checks .............................................................7-7
Interior overview (I).........................................................2-2 Maintenance Requirements ..........................................7-6
Interior overview (II) .......................................................2-3 Scheduled maintenance requirements ..........................7-7
Service requirements ....................................................7-6
J Specified scheduled procedures ...................................7-6
Maintenance under severe usage conditions .................7-12
Jump starting....................................................................6-4
I 5
Index
Manual climate control system......................................3-79
Air conditioning system .............................................3-86
O
Air flow control ..........................................................3-82 Outside rearview mirror.................................................3-70
Air intake control .......................................................3-84 Folding the outside rearview mirrors .........................3-70
Center ventilator .........................................................3-80 Manual type................................................................3-70
Climate control air filter
(for evaporator and blow unit) ..................................3-88 P
Defrosting/defogging..................................................3-85
De-humidified heating................................................3-87 Parking brake .................................................................3-71
Fan speed control (blower control) ............................3-83 Applying the parking brake........................................3-71
Side ventilator.............................................................3-80 Power steering fluid level ..............................................7-52
System operation ........................................................3-85
R
Temperature control ...................................................3-83
Manual transmission........................................................5-8 Rear gate ........................................................................3-74
Anti-lock brake system (ABS) ...................................5-10 To close the rear gate..................................................3-74
Electronic stability control (ESC) .............................5-12 To open the rear gate ..................................................3-74
Esc operation ..............................................................5-13 Rear window defroster switch .......................................3-62
Esc operation off ........................................................5-13 Remote keyless entry .....................................................3-5
Good braking practices ..............................................5-15 Battery replacement......................................................3-6
Good driving practices .................................................5-9 Remote keyless entry system operations......................3-5
Hill-start assist control (HAC) .................................5-14 Transmitter precautions ................................................3-5
Using the clutch............................................................5-9 Replacement of light bulbs ............................................7-56
Measurement....................................................................9-2 Front turn signal light / position light ........................7-58
Multimedia system...........................................................4-2 Headlight Bulb ...........................................................7-56
Care of disc ..................................................................4-4 Interior light (without spectacle case)........................7-62
How vehicle audio works .............................................4-2 License plate light ......................................................7-60
Manual antenna ............................................................4-2 Map light (with spectacle case)..................................7-62
I 6
Index
Rear combination light ...............................................7-59 Side gate.........................................................................3-75
Rear fog light ............................................................7-61 To close the side gate .................................................3-75
Side repeater ..............................................................7-61 To open the side gate..................................................3-75
Road warning...................................................................6-2 Spare tire..........................................................................6-7
Hazard warning flasher ..............................................6-2 Handling the spare tire .................................................6-7
Spare tire anti-theft device ..........................................6-9
S Spare tire pressure ........................................................6-7
Scheduled maintenance ...................................................7-8 Special driving conditions .............................................5-23
Except european community........................................7-8 Driving at night ........................................................5-23
For european community only ...................................7-10 Driving in flooded areas ...........................................5-24
Seat belts........................................................................3-16 Driving in the rain ....................................................5-24
Care of seat belts ........................................................3-19 Driving off-road..........................................................5-24
Do not lie down ..........................................................3-19 Hazardous driving conditions ..................................5-23
Infant or small child ...................................................3-18 Rocking the vehicle ..................................................5-23
Injured person.............................................................3-18 Smooth cornering .......................................................5-24
Larger children ...........................................................3-18 Spectacle case ................................................................3-67
One person per belt ....................................................3-18 Starting.............................................................................5-5
Pregnant women .........................................................3-18 Normal conditions ........................................................5-6
Seat belt precautions ..................................................3-18 Starting and stopping the engine for turbo charger
intercooler....................................................................5-7
Seat belt restraint system............................................3-16
Starting for the diesel engine .......................................5-6
Seat belts (2-point static type) ...................................3-21
Steering wheel ...............................................................3-77
Seat belts 3-point system with emergency
locking retractor ........................................................3-20 Heated steering wheel ...............................................3-78
Seats ...............................................................................3-10 Horn............................................................................3-78
Front seats ..................................................................3-10 Power steering ...........................................................3-77
Rear seat ....................................................................3-13 Steering wheel tilt lever ............................................3-78
To access the engine...................................................3-14 Sun visor ........................................................................3-76
I 7
Index
T W
Ticket holder ..................................................................3-62 Window glass...................................................................3-9
Tire .........................................................................7-32, 9-2 Auto-down window (driver's side) ..............................3-9
Low aspect ratio tire .................................................7-39 Power windows ...........................................................3-9
Recommended inflation pressures .............................7-32 Windshield wiper blades................................................7-23
Tire load and speed capacity ...........................................9-3 Replacing the wiper blades ........................................7-24
Trailer or vehicle towing................................................5-27 Winter driving ................................................................5-25
Safety chains ..............................................................5-28 Carry emergency equipment ......................................5-26
Trailer brakes..............................................................5-27 Change to "winter weight" oil if necessary................5-25
Trailer hitches.............................................................5-27 Check battery and cables............................................5-25
Trailer or vehicle towing tips .....................................5-29 Don't let ice and snow accumulate underneath ..........5-26
Trailer weight limit.....................................................5-28 Don't let your parking brake freeze............................5-26
Snowy or icy conditions.............................................5-25
V To keep locks from freezing.......................................5-25
Vehicle break-in process ..................................................1-4 Use approved anti-freeze in window washer system .5-25
Before operation ...........................................................1-4 Use high quality ethylene glycol coolant...................5-25
During the first 1,000 km (600 miles) .........................1-4 Wipers and washers .......................................................3-59
Loading your vehicle....................................................1-4 Windshield washers....................................................3-60
Vehicle identification number (VIN)...............................8-2 Windshield wipers .....................................................3-59
I 8

H 100 Manual

Uploaded by

Copyright:

Available Formats

H 100 Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

H 100 Manual

Uploaded by

Copyright:

Available Formats

OWNER'S MANUAL

All information in the Owner's Manual is current at the time of publication.

TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION

This manual includes information titled as WARNING, CAUTION and NOTICE.

HYUNDAI MOTOR COMPANY

A100A01L A100A02L A100A04L

table of contents Driving your vehicle 5

HOW TO USE THIS MANUAL FUEL REQUIREMENTS

Biodiesel Repair or replacement of worn or dam-

VEHICLE BREAK-IN PROCESS

INTERIOR OVERVIEW (I)

1. Brake fluid reservoir ...........................7-28

❈ The actual shape may differ from the illustration.

INTERIOR OVERVIEW (II)

1. Heating/Air Conditioning Control

❈ The actual shape may differ from the illustration.

1. Power steering fluid reservoir ...........7-52

❈ The actual shape may differ from the illustration.

■ Diesel Engine (2.6L Engine)

1. Power steering fluid reservoir ...........7-52

❈ The actual shape may differ from the illustration.

Features of your vehicle 3

3 Features of your vehicle

The key code number is WARNING - Ignition key

Immobilizer system (if equipped) ✽ NOTICE

REMOTE KEYLESS ENTRY (IF EQUIPPED)

HHR2048 OHR034105 OHR074110

To access the engine

To Inspect the Engine Compartment

OHR2048 HHR2047 OHR2132

If you continue not to fasten the seat belt

Seat belt precautions Larger Children Injured Person

B210A01L HTB225 HTB226

CHILD RESTRAINT SYSTEM (IF EQUIPPED)

(Continued) (Continued) (Continued)

If you need to tighten the belt, pull more

Child Seat Restraint Suitability For Seat Position

AIR BAG - SUPPLEMENTAL RESTRAINT SYSTEM (IF EQUIPPED)

Noise and smoke ■ Type A Do not install a child restraint on

SRS components and functions Driver’s front air bag (1)

W7-147 The SRSCM continually monitors all B240B01L

B240B02L B240B03L B240B05L

Driver’s front air bag

Passenger’s front air bag

(Continued) (Continued) (Continued)

Why didn’t my air bag go off in a

Air bag collision sensors

OHR012032 OHR012033 OHR012035

OHR012037 OHR012034 OHR012038

SRS Care (Continued)

❈ The actual cluster in the vehicle may dif-

■ Type A Speedometer (km or mile) ■ Type A

When the door is open, or if the engine is

■ Type A On inclines or curves, the fuel gauge

WARNING - Fuel gauge

Average Fuel Economy*

This mode indicates the distance of indi- ■ Type B ✽ NOTICE

■ Type B Automatic reset Warning and indicator lights

High Beam Indicator Anti-lock brake system ESC (Electronic Stability