NSX-SZ10 EZ K HR

NSX-SZ11 LH

NSX-SZ12 EZ

NSX-SZ17 EZ

SERVICE MANUAL
COMPACT DISC
BASIC TAPE MECHANISM : ZZM-2 PR1NM(10/12/17)
BASIC TAPE MECHANISM : ZZM-2 YPR1NM(11)
STEREO SYSTEM BASIC CD MECHANISM : AZG-1 ZA3RNDM(10/12/17)
BASIC CD MECHANISM : AZG-1 YZA3RNDM(11)
CD REMOTE
SYSTEM SPEAKER
CASSEIVER CONTROLLER
NSX–SZ10(EZ/K) CX–NSZ10 SX–NSZ10

NSX–SZ10(HR) CX–NSZ10 SX–NSZ12

RC–ZAS02
NSX–SZ11(LH) CX–NSZ11 SX–NSZ15

NSX–SZ12(EZ) CX–NSZ12 SX–NSZ12

NSX–SZ17(EZ) CX–NSZ17 SX–NSZ10 RC–ZAS17

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
(S/M Code No. 09-003-424-8T1).

• If requiring information about the CD mechanism, see Service Manual of AZG-1,

(S/M Code No. 09-001-335-3NC).
N
SIO
VI
RE

TA
DA

S/M Code No. 09-003-424-8R2

 TABLE OF CONTENTS
SPECIFICATIONS .............................................................................................................................. 3, 4
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING/
Precaution to replace Optical block......................................................................................................... 5
NOTE ON BEFORE STARTING REPAIR .......................................................................................... 6, 7
ELECTRICAL MAIN PARTS LIST ..................................................................................................... 8-13
TRANSISTOR ILLUSTRATION ............................................................................................................ 14
WIRING-1 (MAIN: K, EZ) ................................................................................................................ 15, 16
SCHEMATIC DIAGRAM-1 (MAIN 1/2: K, EZ) ................................................................................. 17, 18
SCHEMATIC DIAGRAM-2 (MAIN 2/2: K, EZ) ................................................................................. 19, 20
WIRING-2 (MAIN: HR) .................................................................................................................... 21, 22
SCHEMATIC DIAGRAM-3 (MAIN 1/2: HR) .................................................................................... 23, 24
SCHEMATIC DIAGRAM-4 (MAIN 2/2: HR) .................................................................................... 25, 26
WIRING-3 (MAIN: LH) ..................................................................................................................... 27, 28
SCHEMATIC DIAGRAM-5 (MAIN 1/2: LH) ..................................................................................... 29, 30
SCHEMATIC DIAGRAM-6 (MAIN 2/2: LH) ..................................................................................... 31, 32
WIRING-4 (FRONT) ........................................................................................................................ 33, 34
SCHEMATIC DIAGRAM-7 (FRONT) .............................................................................................. 35, 36
WIRING-5 (PT: K, EZ) ........................................................................................................................... 37
SCHEMATIC DIAGRAM-8 (PT: K, EZ) ................................................................................................. 38
WIRING-6 (PT: HR) .............................................................................................................................. 39
SCHEMATIC DIAGRAM-9 (PT: HR) ..................................................................................................... 40
WIRING-7 (PT: LH) ............................................................................................................................... 41
SCHEMATIC DIAGRAM-10 (PT: LH) ................................................................................................... 42
WIRING-8 (DECK) ................................................................................................................................ 43
FL (10-BT-224GNK) GRID ASSIGNMENT/ANODE CONNECTION .............................................. 44, 45
IC BLOCK DIAGRAM ...................................................................................................................... 46, 47
ELECTRICAL ADJUSTMENT-1 (K, EZ) ......................................................................................... 48, 49
ELECTRICAL ADJUSTMENT-2 (HR) ............................................................................................. 50, 51
ELECTRICAL ADJUSTMENT-3 (LH) .............................................................................................. 52, 53
IC DESCRIPTION ........................................................................................................................... 54, 55
MECHANICAL PARTS LIST 1/1 ........................................................................................................... 56
MECHANICAL EXPLODED VIEW 1/1 ............................................................................................ 57, 58
TAPE MECHANISM EXPLODED VIEW 1/1 (ZZM-2 PR1NM/PR1NO/YPR1NM) .......................... 59, 60
TAPE MECHANISM PARTS LIST 1/1 (ZZM-2 PR1NM/PR1NO/YPR1NM) ......................................... 61
SPEAKER DISASSEMBLY INSTRUCTIONS ....................................................................................... 62
SPEAKER PARTS LIST 1/1 .................................................................................................................. 63
ACCESSORIES/PACKAGE LIST ......................................................................................................... 63

2
 SPECIFICATIONS
K, EZ MODELS HR MODEL

• Design and specifications are subject to change without

notice .
• Design and specifications are subject to change without
notice .

3
LH MODEL

• Design and specifications are subject to change without notice .

4
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit- CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
tävälle näkymättömälle lasersäteilylle. LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling ZA3/ZA4 MODEL (KSS-213F)
laserstrålning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in

the figure below.

ZA8 MODEL

Solder

5
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step 3
to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2

Select a discharging resistor referring to the following table. Fig-1

Charging voltage (V) Discharging
Rated power (W) Parts number
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.

FRONT C.B MAIN C.B

In some models, it is PIN (.

PIN101 CON601
MICROCOMPUTER
1 1
2 2 OVER LOAD DET POWER AMP

HOLD ( * *
DC DET POWER AMP

AC DET POWER SUPPLY

Q110
PIN number is different HOLD SW
depending upon microprocessor.

Fig-2-1

6
 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.

R
TE
FRONT C.B
PU
M
CO
RO

18 % VSS
IC

15
M

C113 MICRO-
COMPUTER
* VDD
C113
FRONT C.B
Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

7
ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C11 87-010-196-080 CHIP CAPACITOR,0.1-25
<EXCEPT 11LHSC2>
8A-NFA-615-010 C-IC,M38B57MCH-E236FP C11 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
<EXCEPT 12EZ> C12 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
8A-NFA-616-010 C-IC,M38B59MFH-E251FP<12EZ> C12 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A21-397-010 IC,STK490-070<11LHSC2> <EXCEPT 11LHSC2>
87-A21-482-010 IC,RPM6938-H4 C19 87-A10-627-000 CAP,E 2200-50 M SMG<11LHSC2>
87-A21-419-040 C-IC,NJM14558MD-TE2
C20 87-A10-627-000 CAP,E 2200-50 M SMG<11LHSC2>
87-A21-443-040 C-IC,M62495AFP C21 87-016-495-000 CAP,E 3300-25 M SMG<11LHSC2>
87-A21-560-010 IC,LA1844L-A C21 87-A10-520-000 CAP,E 3300-35 M SMG
87-A20-440-040 C-IC,BU1920FS<12EZ> <EXCEPT 11LHSC2>
87-070-127-110 IC,LC72131 D C22 87-016-051-000 CAP,E 2200-35 M SMG
<EXCEPT 11LHSC2>
C22 87-016-495-000 CAP,E 3300-25 M SMG<11LHSC2>
TRANSISTOR
C25 87-010-406-080 CAP, ELECT 22-50<10HR>
87-026-609-080 TR,KTA1266GR C25 87-010-385-080 CAP, ELECT 220-25V<11LHSC2>
89-213-702-010 TR,2SB1370 (1.8W) C25 87-010-407-080 CAP, ELECT 33-50V
87-026-610-080 TR,KTC3198GR <10EZ,12EZ,17EZ,10K>
87-A30-076-080 C-TR,2SC3052F C26 87-010-247-080 CAP, ELECT 100-50V<11LHSC2>
87-A30-075-080 C-TR,2SA1235F C26 87-010-406-080 CAP, ELECT 22-50<EXCEPT 11LHSC2>

87-026-245-080 TR,DTC114ES<10HR,11LHSC2> C30 87-010-384-080 CAP, ELECT 100-25V

87-A30-198-080 TR,KTC3199GR<10HR,11LHSC2> <EXCEPT 11LHSC2>
87-A30-107-070 C-TR,CMBT5401<10HR,11LHSC2> C30 87-010-247-080 CAP, ELECT 100-50V<11LHSC2>
87-A30-484-080 C-TR,KRA102S C31 87-010-263-080 CAP, ELECT 100-10V
87-A30-090-080 FET,2SK2541 <EXCEPT 11LHSC2>
C31 87-010-263-080 CAP, ELECT 100-10V<11LHSC2>
87-A30-468-080 C-TR,KRC102S-RTK C32 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2>
87-A30-190-080 TR,CC5551<10HR>
87-A30-256-010 TR,2SD1933<EXCEPT 11LHSC2> C32 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2>
87-A30-255-010 TR,2SB1342<EXCEPT 11LHSC2> C34 87-010-247-080 CAP, ELECT 100-50V<11LHSC2>
87-A30-106-040 C-TR,CMBT5551<10HR,11LHSC2> C34 87-010-380-080 CAP, ELECT 47-16V<EXCEPT 11LHSC2>
C35 87-010-406-080 CAP, ELECT 22-50
87-A30-091-080 FET,2SJ460 C36 87-010-381-080 CAP, ELECT 330-16V<11LHSC2>
87-A30-062-080 C-TR,KRC104S
87-A30-495-080 TR,2SA1981Y C36 87-010-381-080 CAP, ELECT 330-16V
87-A30-492-080 TR,2SC5343G <EXCEPT 11LHSC2>
87-A30-234-080 TR,CSC4115BC C38 87-010-190-080 S CHIP F 0.01<EXCEPT 11LHSC2>
C38 87-010-190-080 S CHIP F 0.01<11LHSC2>
89-327-143-080 TR,2SC2714 (0.1W) C50 87-010-384-080 CAP, ELECT 100-25V
87-A30-489-080 C-TR,KRA107S <EXCEPT 11LHSC2>
87-A30-074-080 C-TR,RT1P 141C<10HR> C60 87-010-403-080 CAP, ELECT 3.3-50V<11LHSC2>
87-A30-086-040 C-TR,CSD1306E<EXCEPT 11LHSC2>
89-503-602-080 C-FET,2SK360E<EXCEPT 11LHSC2> C60 87-010-403-080 CAP, ELECT 3.3-50V
<EXCEPT 11LHSC2>
C61 87-010-380-080 CAP, ELECT 47-16V<EXCEPT 11LHSC2>
DIODE C61 87-010-260-080 CAP, ELECT 47-25V<11LHSC2>
C97 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
87-020-465-080 DIODE,1SS133 (110MA) C101 87-010-183-080 C-CAP,S 2700P-50 B<11LHSC2>
87-A40-455-080 DIODE,RL203 GW
87-A40-553-080 DIODE,1N4003 LES C101 87-010-185-080 C-CAP,S 3900P-50 B
87-A40-774-080 ZENER,UZ24BSD <EXCEPT 11LHSC2>
87-A40-764-080 ZENER,UZ10BSC C102 87-010-183-080 C-CAP,S 2700P-50 B<11LHSC2>
C102 87-010-185-080 C-CAP,S 3900P-50 B
87-A40-313-080 C-DIODE,MC 2840<11LHSC2> <EXCEPT 11LHSC2>
87-A40-270-080 C-DIODE,MC2838<EXCEPT 10HR> C103 87-010-545-080 CAP, ELECT 0.22-50V
87-A40-269-080 C-DIODE,MC2836<EXCEPT 10HR> <EXCEPT 11LHSC2>
87-A40-768-080 ZENER,UZ16BSA<11LHSC2> C103 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2>
87-A40-752-080 ZENER,UZ6.2BSC
C104 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2>
87-A40-739-080 ZENER,UZ2.7BSA C104 87-010-545-080 CAP, ELECT 0.22-50V
87-A40-618-080 VARI-CAP,SVC 348(S/T)<10HR> <EXCEPT 11LHSC2>
87-017-149-080 ZENER,HZS6A2L C105 87-010-186-080 CAP,CHIP 4700P<EXCEPT 11LHSC2>
C105 87-010-178-080 CHIP CAP 1000P<11LHSC2>
C106 87-010-186-080 CAP,CHIP 4700P<EXCEPT 11LHSC2>
MAIN C.B
C106 87-010-178-080 CHIP CAP 1000P<11LHSC2>
C1 87-010-387-080 CAP,E 470-25 SME<11LHSC2> C107 87-010-403-080 CAP, ELECT 3.3-50V
C1 87-010-387-080 CAP,E 470-25 SME<10HR> <EXCEPT 11LHSC2>
C3 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> C107 87-010-404-080 CAP, ELECT 4.7-50V<11LHSC2>
C4 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> C108 87-010-403-080 CAP, ELECT 3.3-50V
C5 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> <EXCEPT 11LHSC2>
C108 87-010-404-080 CAP, ELECT 4.7-50V<11LHSC2>
C6 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C9 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> C109 87-010-322-080 C-CAP,S 100P-50 CH
C9 87-010-196-080 CHIP CAPACITOR,0.1-25 <10EZ,12EZ,17EZ,10K>
<EXCEPT 11LHSC2> C110 87-010-322-080 C-CAP,S 100P-50 CH
C10 87-010-196-080 CHIP CAPACITOR,0.1-25 <10EZ,12EZ,17EZ,10K>
<EXCEPT 11LHSC2> C111 87-010-406-080 CAP, ELECT 22-50<EXCEPT 11LHSC2>
C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C111 87-010-391-080 CAP,E 10-35 SME<11LHSC2>
<11LHSC2> C112 87-010-406-080 CAP, ELECT 22-50<EXCEPT 11LHSC2>

8
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO. NO. NO.
C112 87-010-391-080 CAP,E 10-35 SME<11LHSC2> C317 87-010-546-080 CAP, ELECT 0.33-50V<11LHSC2> C460 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> C790 87-A12-052-080 C-CAP,S 0.033-25 J B<11LHSC2>
C113 87-A10-946-080 C-CAP,S 220P-100 J CH<10HR> C318 87-010-546-080 CAP, ELECT 0.33-50V C460 87-010-196-080 CHIP CAPACITOR,0.1-25 C791 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C113 87-012-156-080 C-CAP,S 220P-50 CH <EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C791 87-010-196-080 CHIP CAPACITOR,0.1-25
<10EZ,12EZ,17EZ,10K> C318 87-010-546-080 CAP, ELECT 0.33-50V C461 87-012-158-080 C-CAP,S 390P-50 CH<11LHSC2> <EXCEPT 11LHSC2>
C113 87-010-405-080 CAP, ELECT 10-50V<11LHSC2> <11LHSC2> C461 87-012-158-080 C-CAP,S 390P-50 CH C792 87-010-197-080 CAP, CHIP 0.01 DM
C114 87-A10-946-080 C-CAP,S 220P-100 J CH<10HR> C320 87-010-196-080 CAP,TC U 0.1-50 Z F <EXCEPT 11LHSC2> C793 87-010-404-080 CAP, ELECT 4.7-50V<11LHSC2>
<10EZ,12EZ,17EZ,10K> C462 87-012-158-080 C-CAP,S 390P-50 CH<11LHSC2>
C114 87-012-156-080 C-CAP,S 220P-50 CH C321 87-010-196-080 CAP,TC U 0.1-50 Z F C462 87-012-158-080 C-CAP,S 390P-50 CH C793 87-010-404-080 CAP, ELECT 4.7-50V
<10EZ,12EZ,17EZ,10K> <10EZ,12EZ,17EZ,10K> <EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C114 87-010-405-080 CAP, ELECT 10-50V<11LHSC2> C794 87-010-322-080 C-CAP,S 100P-50 CH
C119 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C324 87-010-196-080 CAP,TC U 0.1-50 Z F C470 87-018-127-080 CAP, CER 470P-50V<EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K>
C119 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K> C605 87-010-179-080 CAP,CHIP S B1200P<EXCEPT 11LHSC2> C795 87-010-197-080 CAP, CHIP 0.01 DM
C120 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C325 87-010-196-080 CAP,TC U 0.1-50 Z F C605 87-010-179-080 CAP,CHIP S B1200P<11LHSC2> C796 87-010-197-080 CAP, CHIP 0.01 DM
<10EZ,12EZ,17EZ,10K> C606 87-010-179-080 CAP,CHIP S B1200P<11LHSC2> C797 87-010-405-080 CAP, ELECT 10-50V<11LHSC2>
C120 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C326 87-010-198-080 CAP, CHIP 0.022<11LHSC2> C606 87-010-179-080 CAP,CHIP S B1200P<EXCEPT 11LHSC2>
C123 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 10HR> C326 87-010-198-080 CAP, CHIP 0.022<EXCEPT 11LHSC2> C797 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 11LHSC2>
C124 87-010-197-080 CAP, CHIP 0.01 DM C327 87-010-196-080 CHIP CAPACITOR,0.1-25 C609 87-010-213-080 C-CAP,S 0.015-50 B C798 87-010-197-080 CAP, CHIP 0.01 DM
<10EZ,12EZ,17EZ,10K> <EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C799 87-010-407-080 CAP, ELECT 33-50V<EXCEPT 11LHSC2>
C125 87-012-368-080 C-CAP,S 0.1-50 F<11LHSC2> C609 87-010-213-080 C-CAP,S 0.015-50 B<11LHSC2> C799 87-010-407-080 CAP, ELECT 33-50V<11LHSC2>
C125 87-010-196-080 CHIP CAPACITOR,0.1-25 C327 87-010-196-080 CHIP CAPACITOR,0.1-25 C610 87-010-213-080 C-CAP,S 0.015-50 B C800 87-012-369-080 C-CAP,S 0.047-50F<11LHSC2>
<EXCEPT 11LHSC2> <11LHSC2> <EXCEPT 11LHSC2>
C350 87-010-196-080 CAP,TC U 0.1-50 Z F C610 87-010-213-080 C-CAP,S 0.015-50 B<11LHSC2> C800 87-012-369-080 C-CAP,S 0.047-50F<EXCEPT 11LHSC2>
C126 87-012-368-080 C-CAP,S 0.1-50 F<11LHSC2> <10EZ,12EZ,17EZ,10K> C611 87-010-545-080 CAP, ELECT 0.22-50V C801 87-010-403-080 CAP, ELECT 3.3-50V
C126 87-010-196-080 CHIP CAPACITOR,0.1-25 C360 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C802 87-012-369-080 C-CAP,S 0.047-50F<11LHSC2>
<EXCEPT 11LHSC2> C360 87-010-401-080 CAP, ELECT 1-50V<11LHSC2> C802 87-012-369-080 C-CAP,S 0.047-50F<EXCEPT 11LHSC2>
C127 87-012-368-080 C-CAP,S 0.1-50 F<11LHSC2> C363 87-010-197-080 CAP, CHIP 0.01 DM C611 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2> C803 87-010-198-080 CAP, CHIP 0.022<11LHSC2>
C127 87-010-196-080 CHIP CAPACITOR,0.1-25 <10EZ,12EZ,17EZ,10K> C612 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2>
<EXCEPT 11LHSC2> C612 87-010-545-080 CAP, ELECT 0.22-50V C803 87-010-198-080 CAP, CHIP 0.022<EXCEPT 11LHSC2>
C128 87-012-368-080 C-CAP,S 0.1-50 F<11LHSC2> C399 87-012-140-080 CAP 470P<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C804 87-010-263-080 CAP, ELECT 100-10V<11LHSC2>
C399 87-012-140-080 CAP 470P<11LHSC2> C613 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2> C804 87-010-263-080 CAP, ELECT 100-10V
C128 87-010-196-080 CHIP CAPACITOR,0.1-25 C401 87-010-544-080 CAP, ELECT 0.1-50V C613 87-010-545-080 CAP, ELECT 0.22-50V <EXCEPT 11LHSC2>
<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C807 87-010-400-080 CAP, ELECT 0.47-50V
C129 87-A10-592-080 C-CAP,S 0.015-50 J B<11LHSC2> C401 87-010-544-080 CAP, ELECT 0.1-50V<11LHSC2> C808 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 11LHSC2>
C130 87-A10-592-080 C-CAP,S 0.015-50 J B<11LHSC2> C402 87-010-544-080 CAP, ELECT 0.1-50V<11LHSC2> C614 87-010-545-080 CAP, ELECT 0.22-50V
C131 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> <EXCEPT 11LHSC2> C808 87-010-401-080 CAP, ELECT 1-50V<11LHSC2>
C132 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C402 87-010-544-080 CAP, ELECT 0.1-50V C614 87-010-545-080 CAP, ELECT 0.22-50V<11LHSC2> C809 87-010-401-080 CAP, ELECT 1-50V<11LHSC2>
<EXCEPT 11LHSC2> C615 87-010-154-080 CAP CHIP 10P<11LHSC2> C809 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 11LHSC2>
C133 87-010-186-080 CAP,CHIP 4700P<11LHSC2> C403 87-010-321-080 CHIP CAPACITOR,82P(J)<11LHSC2> C615 87-010-154-080 CAP CHIP 10P<EXCEPT 11LHSC2> C810 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C133 87-010-186-080 CAP,CHIP 4700P<EXCEPT 11LHSC2> C403 87-010-321-080 CHIP CAPACITOR,82P(J) C616 87-010-248-080 CAP, ELECT 220-10V C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C140 87-010-182-080 C-CAP,S 2200P-50 B <EXCEPT 11LHSC2> <EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
<EXCEPT 11LHSC2> C404 87-010-321-080 CHIP CAPACITOR,82P(J)
C140 87-010-182-080 C-CAP,S 2200P-50 B<11LHSC2> <EXCEPT 11LHSC2> C616 87-010-385-080 CAP, ELECT 220-25V<11LHSC2> C811 87-010-403-080 CAP, ELECT 3.3-50V<10HR>
C301 87-010-179-080 CAP,CHIP S B1200P<EXCEPT 11LHSC2> C404 87-010-321-080 CHIP CAPACITOR,82P(J)<11LHSC2> C617 87-010-248-080 CAP, ELECT 220-10V C812 87-010-403-080 CAP, ELECT 3.3-50V<10HR>
<EXCEPT 11LHSC2> C814 87-010-197-080 CAP, CHIP 0.01 DM
C301 87-010-179-080 CAP,CHIP S B1200P<11LHSC2> C405 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C617 87-010-385-080 CAP, ELECT 220-25V<11LHSC2> C815 87-010-400-080 CAP, ELECT 0.47-50V
C302 87-010-179-080 CAP,CHIP S B1200P<EXCEPT 11LHSC2> C405 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C618 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C302 87-010-179-080 CAP,CHIP S B1200P<11LHSC2> C406 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C618 87-010-405-080 CAP, ELECT 10-50V<11LHSC2> C815 87-010-403-080 CAP, ELECT 3.3-50V<11LHSC2>
C303 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> C406 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2>
C303 87-010-178-080 CHIP CAP 1000P<11LHSC2> C407 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C630 87-016-669-080 C-CAP,S 0.1-25 K B C816 87-010-400-080 CAP, ELECT 0.47-50V
<EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C304 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> C407 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C630 87-016-669-080 C-CAP,S 0.1-25 K B<11LHSC2> C816 87-010-403-080 CAP, ELECT 3.3-50V<11LHSC2>
C304 87-010-178-080 CHIP CAP 1000P<11LHSC2> C408 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C669 87-010-322-080 C-CAP,S 100P-50 CH C818 87-010-180-080 C-CER 1500P<10EZ,12EZ,17EZ,10K>
C305 87-010-198-080 CAP, CHIP 0.022<EXCEPT 11LHSC2> C408 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> <10EZ,12EZ,17EZ,10K> C821 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 11LHSC2>
C307 87-010-263-080 CAP, ELECT 100-10V<11LHSC2> C409 87-010-182-080 C-CAP,S 2200P-50 B<11LHSC2> C669 87-010-322-080 C-CAP,S 100P-50 CH<11LHSC2> C821 87-010-405-080 CAP, ELECT 10-50V<11LHSC2>
C307 87-010-263-080 CAP, ELECT 100-10V C409 87-010-182-080 C-CAP,S 2200P-50 B C670 87-010-322-080 C-CAP,S 100P-50 CH
<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K> C823 87-012-349-080 C-CAP,S 1000P-50 CH
<10EZ,12EZ,17EZ,10K>
C308 87-010-263-080 CAP, ELECT 100-10V<11LHSC2> C410 87-010-182-080 C-CAP,S 2200P-50 B C670 87-010-322-080 C-CAP,S 100P-50 CH<11LHSC2> C823 87-010-177-080 C-CAP,S 820P-50 SL<10HR>
C308 87-010-263-080 CAP, ELECT 100-10V <EXCEPT 11LHSC2> C677 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C823 87-010-177-080 C-CAP,S 820P-50 SL<11LHSC2>
<EXCEPT 11LHSC2> C410 87-010-182-080 C-CAP,S 2200P-50 B<11LHSC2> C677 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C824 87-010-404-080 CAP, ELECT 4.7-50V
C309 87-010-318-080 C-CAP,S 47P-50 CH<10HR> C411 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 11LHSC2> C771 87-010-263-080 CAP, ELECT 100-10V<11LHSC2> <EXCEPT 11LHSC2>
C309 87-010-318-080 C-CAP,S 47P-50 CH<11LHSC2> C411 87-010-405-080 CAP, ELECT 10-50V<11LHSC2> C771 87-010-263-080 CAP, ELECT 100-10V C824 87-010-404-080 CAP, ELECT 4.7-50V<11LHSC2>
C309 87-010-311-080 CAP 12P<10EZ,12EZ,17EZ,10K> C412 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C825 87-010-596-080 CAP, S 0.047-16<11LHSC2>
C310 87-010-314-080 C-CAP,S 22P-50V C412 87-010-405-080 CAP, ELECT 10-50V<11LHSC2> C772 87-010-197-080 CAP, CHIP 0.01 DM C825 87-010-596-080 CAP, S 0.047-16<EXCEPT 11LHSC2>
<10EZ,12EZ,17EZ,10K> C452 87-010-382-080 CAP, ELECT 22-25V<11LHSC2> C779 87-010-971-080 C-CAP,S 4700P-50 B J C831 87-010-406-080 CAP, ELECT 22-50
C310 87-010-318-080 C-CAP,S 47P-50 CH<11LHSC2> C452 87-010-382-080 CAP, ELECT 22-25V<EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K> <10EZ,12EZ,17EZ,10K>
C310 87-010-318-080 C-CAP,S 47P-50 CH<10HR> C453 87-010-183-080 C-CAP,S 2700P-50 B C780 87-010-971-080 C-CAP,S 4700P-50 B J C842 87-010-197-080 CAP, CHIP 0.01 DM
C311 87-010-598-080 C-CAP,S 0.068-16VRK <EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K> C844 87-010-197-080 CAP, CHIP 0.01 DM
<EXCEPT 11LHSC2> C453 87-010-183-080 C-CAP,S 2700P-50 B<11LHSC2> C782 87-010-197-080 CAP, CHIP 0.01 DM
C312 87-010-598-080 C-CAP,S 0.068-16VRK C783 87-010-197-080 CAP, CHIP 0.01 DM C850 87-010-260-080 CAP, ELECT 47-25V<11LHSC2>
<EXCEPT 11LHSC2> C454 87-010-183-080 C-CAP,S 2700P-50 B C850 87-010-260-080 CAP, ELECT 47-25V<EXCEPT 11LHSC2>
<EXCEPT 11LHSC2> C784 87-010-197-080 CAP, CHIP 0.01 DM C851 87-010-197-080 CAP, CHIP 0.01 DM
C313 87-010-188-080 CAP,CHIP 6800P<EXCEPT 11LHSC2> C454 87-010-183-080 C-CAP,S 2700P-50 B<11LHSC2> C785 87-010-197-080 CAP, CHIP 0.01 DM C852 87-010-197-080 CAP, CHIP 0.01 DM
C313 87-010-188-080 CAP,CHIP 6800P<11LHSC2> C455 87-010-183-080 C-CAP,S 2700P-50 B<11LHSC2> C786 87-010-197-080 CAP, CHIP 0.01 DM C853 87-010-197-080 CAP, CHIP 0.01 DM
C314 87-010-188-080 CAP,CHIP 6800P<EXCEPT 11LHSC2> C455 87-010-183-080 C-CAP,S 2700P-50 B C788 87-010-149-080 C-CAP,S 5P-50 CH<11LHSC2>
C314 87-010-188-080 CAP,CHIP 6800P<11LHSC2> <EXCEPT 11LHSC2> C788 87-010-149-080 C-CAP,S 5P-50 CH<EXCEPT 11LHSC2> C858 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C315 87-010-263-080 CAP, ELECT 100-10V<11LHSC2> C456 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> C858 87-010-196-080 CHIP CAPACITOR,0.1-25
C789 87-A10-801-080 C-CAP,S 0.022-16 J B CM <EXCEPT 11LHSC2>
C315 87-010-263-080 CAP, ELECT 100-10V C456 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C859 87-010-196-080 CHIP CAPACITOR,0.1-25
<EXCEPT 11LHSC2> C458 87-010-178-080 CHIP CAP 1000P C789 87-A12-052-080 C-CAP,S 0.033-25 J B<11LHSC2> <EXCEPT 11LHSC2>
C317 87-010-546-080 CAP, ELECT 0.33-50V <10EZ,12EZ,17EZ,10K> C790 87-A10-801-080 C-CAP,S 0.022-16 J B CM C859 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
<EXCEPT 11LHSC2> C459 87-010-175-080 CAP 560P<10EZ,12EZ,17EZ,10K> <EXCEPT 11LHSC2> C860 87-010-197-080 CAP, CHIP 0.01 DM

9 10
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO. NO. NO.
C869 87-010-197-080 CAP, CHIP 0.01 DM<12EZ> C998 87-010-260-080 CAP, ELECT 47-25V<EXCEPT 11LHSC2> L944 87-A50-159-010 COIL,10MH K C2B<10HR> C120 87-012-156-080 C-CAP,S 220P-50 CH
C870 87-010-178-080 CHIP CAP 1000P<12EZ> C998 87-010-260-080 CAP, ELECT 47-25V<11LHSC2> L951 8A-NF8-668-010 COIL,AM PACK 2(TOK) <EXCEPT 11LHSC2>
C871 87-012-156-080 C-CAP,S 220P-50 CH<12EZ> C999 87-A11-155-080 CAP,TC U 0.01-16 Z F<11LHSC2> <10EZ,12EZ,17EZ,10K> C120 87-012-156-080 C-CAP,S 220P-50 CH<11LHSC2>
C872 87-012-156-080 C-CAP,S 220P-50 CH<12EZ> C999 87-A11-155-080 CAP,TC U 0.01-16 Z F L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)<11LHSC2> C123 87-010-196-080 CHIP CAPACITOR,0.1-25
C873 87-012-140-080 CAP 470P<12EZ> <EXCEPT 11LHSC2> L952 87-A50-430-010 COIL,ANT MW(3BSW)<10HR> <EXCEPT 11LHSC2>
CF831 87-008-423-010 CERAMIC FILTER, SFE10.7 L953 87-A50-431-010 COIL,OSC MW(3BSW)<10HR> C124 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C874 87-010-405-080 CAP, ELECT 10-50V<12EZ> <10EZ,12EZ,17EZ,10K> C124 87-010-196-080 CHIP CAPACITOR,0.1-25
C875 87-010-196-080 CHIP CAPACITOR,0.1-25<12EZ> R129 87-A00-258-080 RES,M/F 0.22-1W J<10HR> <EXCEPT 11LHSC2>
C876 87-010-405-080 CAP, ELECT 10-50V<12EZ> CF831 87-008-261-010 FILTER, SFE10.7MA5-A<11LHSC2> R130 87-A00-258-080 RES,M/F 0.22-1W J<10HR>
C877 87-010-197-080 CAP, CHIP 0.01 DM<12EZ> CF831 87-008-261-010 FILTER, SFE10.7MA5-A<10HR> R131 87-A00-258-080 RES,M/F 0.22-1W J<11LHSC2> C125 87-010-405-040 CAP,E 10-50<EXCEPT 11LHSC2>
C878 87-010-316-080 C-CAP,S 33P-50 CH<12EZ> CF832 82-785-747-010 CF MS2 GHY R<10EZ,12EZ,17EZ,10K> R132 87-A00-258-080 RES,M/F 0.22-1W J<11LHSC2> C125 87-010-405-040 CAP,E 10-50<11LHSC2>
CF832 87-008-261-010 FILTER, SFE10.7MA5-A<11LHSC2> R143 87-A00-440-050 RES,220-1/2W J RP<11LHSC2> C126 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2>
C879 87-010-314-080 C-CAP,S 22P-50V<12EZ> CF832 87-008-261-010 FILTER, SFE10.7MA5-A<10HR> C126 87-010-196-080 CHIP CAPACITOR,0.1-25
C940 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> R144 87-A00-440-050 RES,220-1/2W J RP<11LHSC2> <EXCEPT 11LHSC2>
C941 87-010-314-080 C-CAP,S 22P-50V<10HR> CN301 87-A60-620-010 CONN,3P V 2MM JMT<11LHSC2> R145 87-A00-440-050 RES,220-1/2W J RP<11LHSC2> C129 87-010-374-040 CAP,E 47-10<EXCEPT 11LHSC2>
C942 87-010-149-080 C-CAP,S 5P-50 CH CN301 87-A60-620-010 CONN,3P V 2MM JMT<EXCEPT 11LHSC2> R146 87-A00-440-050 RES,220-1/2W J RP<11LHSC2>
<10EZ,12EZ,17EZ,10K> CN351 87-A60-625-010 CONN,8P V 2MM JMT<EXCEPT 11LHSC2> R991 87-010-322-080 C-CAP,S 100P-50 CH<11LHSC2> C129 87-010-374-040 CAP,E 47-10<11LHSC2>
C943 87-010-197-080 CAP, CHIP 0.01 DM<10HR> CN351 87-A60-625-010 CONN,8P V 2MM JMT<11LHSC2> R993 87-010-322-080 C-CAP,S 100P-50 CH<11LHSC2> C210 87-012-156-080 C-CAP,S 220P-50 CH
CN601 87-099-719-010 CONN,30P TYK-B(X)<11LHSC2> <EXCEPT 11LHSC2>
C945 87-010-197-080 CAP, CHIP 0.01 DM<10HR> R995 87-010-322-080 C-CAP,S 100P-50 CH<11LHSC2> C210 87-012-156-080 C-CAP,S 220P-50 CH<11LHSC2>
C946 87-010-971-080 C-CAP,S 4700P-50 B J<10HR> CN601 87-099-719-010 CONN,30P TYK-B(X)<EXCEPT 11LHSC2> TC941 87-011-254-080 TRIMER,20P LAR<10HR> C212 87-010-404-040 CAP,E 4.7-50 SME<11LHSC2>
C947 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> CN602 87-099-194-010 CONN,6P 6216V<EXCEPT 11LHSC2> TC943 87-011-253-080 TRIMER,30P LAR<10HR> C212 87-010-404-040 CAP,E 4.7-50 SME<EXCEPT 11LHSC2>
C948 87-012-140-080 CAP 470P<10EZ,12EZ,17EZ,10K> CN602 87-099-194-010 CONN,6P 6216V<11LHSC2> VR401 87-NB7-602-010 VR,RTRY 10KAX1 1 V<10HR>
C948 87-010-148-080 CAP, CHIP S 4P SL<10HR> CNA1 8A-NF8-652-010 CONN ASSY,7P TID-A(480)<10HR> W181 85-NF5-628-010 F-CABLE 7P-2.5 C213 87-010-404-040 CAP,E 4.7-50 SME<EXCEPT 11LHSC2>
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480)<11LHSC2> <10EZ,12EZ,17EZ,10K> C213 87-010-404-040 CAP,E 4.7-50 SME<11LHSC2>
C952 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> FB301 87-008-372-080 FILTER, EMI BL OIRNI C401 87-010-186-080 CAP,CHIP 4700P<10HR>
C953 87-010-197-080 CAP, CHIP 0.01 DM<10HR> <10EZ,12EZ,17EZ,10K> WH1 87-A90-460-010 HLDR,WIRE 2.5-7P<EXCEPT 11LHSC2> C402 87-010-060-040 CAP,E 100-16<10HR>
C954 87-010-400-080 CAP, ELECT 0.47-50V<10HR> WH1 87-A90-510-010 HLDR,WIRE 2.5-9P<11LHSC2> C403 87-010-545-040 CAP,E 0.22-50 SME<10HR>
C956 87-010-263-080 CAP, ELECT 100-10V<10HR> FB602 87-008-372-080 FILTER, EMI BL OIRNI X861 87-A70-091-010 VIB,XTAL 4.332MHZ CSA-309<12EZ>
C957 87-010-311-080 CAP 12P<10EZ,12EZ,17EZ,10K> <10EZ,12EZ,17EZ,10K> X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309 C404 87-010-322-080 C-CAP,S 100P-50 CH<10HR>
FFE831 A8-6ZA-191-130 6ZA-1 FEENM<10EZ,12EZ,17EZ,10K> <EXCEPT 11LHSC2> C405 87-010-545-040 CAP,E 0.22-50 SME<10HR>
C958 87-010-197-080 CAP, CHIP 0.01 DM FFE831 A8-8ZA-190-030 8ZA-1 FEUNM<10HR> X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309 C406 87-016-669-080 C-CAP,S 0.1-25 K B<10HR>
<10EZ,12EZ,17EZ,10K> FFE831 A8-8ZA-191-030 8ZA-1 YFEUNM<11LHSC2> <11LHSC2> C407 87-010-405-040 CAP,E 10-50<10HR>
C959 87-010-196-080 CHIP CAPACITOR,0.1-25 J101 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC C408 87-010-322-080 C-CAP,S 100P-50 CH<10HR>
<EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C959 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> FRONT C.B C409 87-010-378-040 CAP,E 10-16<10HR>
C960 87-010-196-080 CHIP CAPACITOR,0.1-25 J103 87-A60-238-010 TERMINAL,SP 4P (MSC) C410 87-010-196-080 CHIP CAPACITOR,0.1-25<10HR>
<EXCEPT 10HR> <EXCEPT 11LHSC2> C101 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> C412 87-010-177-080 C-CAP,S 820P-50 SL<10HR>
C961 87-010-152-080 C-CAP,S 8P-50 CH<11LHSC2> J202 87-A60-602-010 JACK,DIA6.3 BLK ST W/SW TC C101 87-010-196-080 CHIP CAPACITOR,0.1-25 C701 87-010-384-040 CAP,E 100-25 SME<11LHSC2>
<11LHSC2> <EXCEPT 11LHSC2> C701 87-010-384-040 CAP,E 100-25 SME<EXCEPT 11LHSC2>
C962 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 11LHSC2> J203 87-A60-238-010 TERMINAL,SP 4P (MSC)<11LHSC2> C102 87-012-369-080 C-CAP,S 0.047-50F<11LHSC2>
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z J401 87-A61-243-010 JACK,6.3 BLK MONO W/SW V MSC C102 87-012-369-080 C-CAP,S 0.047-50F<EXCEPT 11LHSC2> CN101 87-099-720-010 CONN,30P TYK-B(P)
<EXCEPT 11LHSC2> <10HR> C103 87-010-374-040 CAP,E 47-10<11LHSC2> CN701 87-A60-673-010 CONN,9P H 2MM JMT
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN CN801 87-099-015-010 CONN,13P 6216V
<11LHSC2> <11LHSC2> C103 87-010-374-040 CAP,E 47-10<EXCEPT 11LHSC2> EMI401 87-008-372-080 FILTER, EMI BL OIRNI<10HR>
C964 87-010-854-080 C-CAP,S 560PCH<10HR> C104 87-A10-797-040 CAP,E 47-35 M 5L SRM FL201 8A-NFA-604-010 FL,10-BT-224GNK
C971 87-010-381-080 CAP, ELECT 330-16V J602 87-A60-881-010 JACK,PIN 2P MSP 242V05 PBSN <11LHSC2>
<EXCEPT 11LHSC2> <EXCEPT 11LHSC2> C104 87-A10-797-040 CAP,E 47-35 M 5L SRM L101 87-A50-434-010 COIL,CLK 4.19M(TOKO)
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02<10HR> <EXCEPT 11LHSC2> LED101 87-A40-317-080 LED,SLR-342VCT31 RED
C971 87-010-381-080 CAP, ELECT 330-16V<11LHSC2> J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 C105 87-010-192-080 C-CAP,S 0.022-50 F S101 87-A91-555-010 SW,RTRY EC12E24504
C972 87-010-404-080 CAP, ELECT 4.7-50V<11LHSC2> <11LHSC2> <EXCEPT 11LHSC2> S301 87-A90-164-080 SW,TACT SKQAB(N)
C972 87-010-404-080 CAP, ELECT 4.7-50V J832 87-A60-403-010 TERMINAL,ANT PAL 2P HSP-312V05 C105 87-010-192-080 C-CAP,S 0.022-50 F<11LHSC2> S302 87-A90-164-080 SW,TACT SKQAB(N)
<EXCEPT 11LHSC2> <10EZ,12EZ,17EZ,10K>
C973 87-010-197-080 CAP, CHIP 0.01 DM J940 87-A60-633-010 CONN,2P H 2.5MM JMT<10HR> C107 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> S303 87-A90-164-080 SW,TACT SKQAB(N)
C974 87-010-197-080 CAP, CHIP 0.01 DM C107 87-010-196-080 CHIP CAPACITOR,0.1-25 S304 87-A90-164-080 SW,TACT SKQAB(N)
L101 87-A50-610-010 COIL,1UH K(MDEC)<11LHSC2> <EXCEPT 11LHSC2> S305 87-A90-164-080 SW,TACT SKQAB(N)
C979 87-010-322-080 C-CAP,S 100P-50 CH L101 87-A50-610-010 COIL,1UH K(MDEC)<EXCEPT 11LHSC2> C108 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> S306 87-A90-164-080 SW,TACT SKQAB(N)
C981 87-010-260-080 CAP, ELECT 47-25V<EXCEPT 11LHSC2> L102 87-A50-610-010 COIL,1UH K(MDEC)<11LHSC2> C108 87-010-178-080 CHIP CAP 1000P<11LHSC2> S307 87-A90-164-080 SW,TACT SKQAB(N)
C981 87-010-260-080 CAP, ELECT 47-25V<11LHSC2> L102 87-A50-610-010 COIL,1UH K(MDEC)<EXCEPT 11LHSC2> C109 87-012-369-080 C-CAP,S 0.047-50F<EXCEPT 11LHSC2>
C982 87-010-196-080 CHIP CAPACITOR,0.1-25 L451 87-007-342-010 COIL,OSC 85K BIAS<EXCEPT 11LHSC2> S308 87-A90-164-080 SW,TACT SKQAB(N)
<EXCEPT 11LHSC2> C109 87-012-369-080 C-CAP,S 0.047-50F<11LHSC2> S309 87-A90-164-080 SW,TACT SKQAB(N)
C982 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> L451 87-007-342-010 COIL,OSC 85K BIAS<11LHSC2> C110 87-010-197-080 CAP, CHIP 0.01 DM<11LHSC2> S310 87-A90-164-080 SW,TACT SKQAB(N)<12EZ>
L801 87-A50-608-010 COIL,FM DET-N(TOK)<11LHSC2> C110 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> S311 87-A90-164-080 SW,TACT SKQAB(N)<12EZ>
C983 87-010-197-080 CAP, CHIP 0.01 DM L801 87-A50-608-010 COIL,FM DET-N(TOK) C111 87-010-196-080 CHIP CAPACITOR,0.1-25 S312 87-A90-164-080 SW,TACT SKQAB(N)<12EZ>
C984 87-010-197-080 CAP, CHIP 0.01 DM <EXCEPT 11LHSC2> <EXCEPT 11LHSC2>
C985 87-010-322-080 C-CAP,S 100P-50 CH L802 87-A91-552-010 FLTR,CFMT-450AL (TOK)<10HR> C111 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> S321 87-A90-164-080 SW,TACT SKQAB(N)
<10EZ,12EZ,17EZ,10K> L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) S322 87-A90-164-080 SW,TACT SKQAB(N)
C987 87-010-197-080 CAP, CHIP 0.01 DM <10EZ,12EZ,17EZ,10K> C113 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> S323 87-A90-164-080 SW,TACT SKQAB(N)
C989 87-010-197-080 CAP, CHIP 0.01 DM<EXCEPT 11LHSC2> C113 87-010-178-080 CHIP CAP 1000P<11LHSC2> S324 87-A90-164-080 SW,TACT SKQAB(N)
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK)<11LHSC2> C114 87-010-154-080 CAP CHIP 10P<EXCEPT 11LHSC2> S325 87-A90-164-080 SW,TACT SKQAB(N)
C991 87-010-312-080 C-CAP,S 15P-50 CH<11LHSC2> L811 87-005-847-080 COIL,2.2UH(CECS)<11LHSC2> C114 87-010-154-080 CAP CHIP 10P<11LHSC2>
C991 87-010-312-080 C-CAP,S 15P-50 CH<EXCEPT 11LHSC2> L811 87-005-847-080 COIL,2.2UH(CECS)<EXCEPT 11LHSC2> C115 87-010-175-080 CAP 560P<11LHSC2> S326 87-A90-164-080 SW,TACT SKQAB(N)
C992 87-010-312-080 C-CAP,S 15P-50 CH<11LHSC2> L832 87-005-847-080 COIL,2.2UH(CECS)<EXCEPT 11LHSC2> S327 87-A90-164-080 SW,TACT SKQAB(N)
C992 87-010-312-080 C-CAP,S 15P-50 CH<EXCEPT 11LHSC2> L832 87-005-847-080 COIL,2.2UH(CECS)<11LHSC2> C115 87-010-175-080 CAP 560P<EXCEPT 11LHSC2> S328 87-A90-164-080 SW,TACT SKQAB(N)
C993 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> C116 87-010-400-040 CAP,E 0.47-50<11LHSC2> S329 87-A90-164-080 SW,TACT SKQAB(N)
L861 87-005-847-080 COIL,2.2UH(CECS)<12EZ> C116 87-010-400-040 CAP,E 0.47-50<EXCEPT 11LHSC2> S330 87-A90-164-080 SW,TACT SKQAB(N)
C993 87-010-178-080 CHIP CAP 1000P<11LHSC2> L941 87-A50-020-010 COIL,ANT LW(COI) C117 87-016-460-080 C-CAP,S 0.22-16 B<EXCEPT 11LHSC2>
C995 87-010-178-080 CHIP CAP 1000P<11LHSC2> <10EZ,12EZ,17EZ,10K> C117 87-016-460-080 C-CAP,S 0.22-16 B<11LHSC2> S331 87-A90-164-080 SW,TACT SKQAB(N)
C995 87-010-178-080 CHIP CAP 1000P<EXCEPT 11LHSC2> L941 87-A50-022-010 COIL,ANT SW(COI)<10HR> SFR701 87-024-431-080 SFR,3.3K RH063EC
C997 87-010-196-080 CHIP CAPACITOR,0.1-25<11LHSC2> L942 87-A50-019-010 COIL,OSC LW(COI) C118 87-A10-189-040 CAP,E 220-10<EXCEPT 11LHSC2>
C997 87-010-196-080 CHIP CAPACITOR,0.1-25 <10EZ,12EZ,17EZ,10K> C118 87-A10-189-040 CAP,E 220-10<11LHSC2>
<EXCEPT 11LHSC2> L942 87-A50-550-010 COIL,OSC SW-2N(COI)<10HR> C119 87-A10-189-040 CAP,E 220-10<11LHSC2>
L943 87-A50-522-080 COIL,1MH K CEC<10HR> C119 87-A10-189-040 CAP,E 220-10<EXCEPT 11LHSC2>

11 12
 TRANSISTOR ILLUSTRATION

REF. NO PART NO. KANRI DESCRIPTION

NO.
PT C.B

C31 87-010-403-080 CAP, ELECT 3.3-50V<10HR>

C31 87-010-403-080 CAP, ELECT 3.3-50V<11LHSC2>
C183 87-010-387-080 CAP,E 470-25 SME E C B S D G E C B B C E
<10EZ,12EZ,17EZ,10K>
C184 87-010-403-080 CAP, ELECT 3.3-50V
<10EZ,12EZ,17EZ,10K> 2SJ460 2SB1370
C185 87-018-209-080 CAP, CER 0.1-50V CSA952 DTC114ES
<10EZ,12EZ,17EZ,10K> CSC4115 2SK2541 2SB1342
KTA1266 2SD1933
CN1 87-A61-109-010 CONN,7P V TID-A<10HR>
CN1 87-A61-110-010 CONN,9P V TID-A<11LHSC2> KTC3198
!PT1 8A-NFA-606-010 PT,ANF-A HR<10HR> KTC3199
!PT1 8A-NFA-608-010 PT,ANF-A EZ<10EZ,12EZ,17EZ,10K>
!PT1 8A-NFA-609-010 PT,ANF-A LH<11LHSC2>

!PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI<10HR>

!PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI<11LHSC2>
!PT181 8A-NF8-662-010 PT,SUB ANF-8 (E)
<10EZ,12EZ,17EZ,10K>
!RY1 87-A91-281-010 RELAY,AC DC12V OSA-SS-212DM5 C
<11LHSC2>
!RY1 87-A91-281-010 RELAY,AC DC12V OSA-SS-212DM5
<10HR>
B
!RY181 87-A90-976-010 RELAY,AC12V SDT-S-112LMR E
<10EZ,12EZ,17EZ,10K>
!S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<10HR>
!S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<11LHSC2> B C E E B C
T1 87-A60-317-010 TERMINAL, 1P MSC<10HR>
T1 87-A60-317-010 TERMINAL, 1P MSC<11LHSC2>
2SC3331 CC5551 2SA1235 KRA102
T2 87-A60-317-010 TERMINAL, 1P MSC<10HR> 2SC2714 KRA107
T2 87-A60-317-010 TERMINAL, 1P MSC<11LHSC2>
T181 87-A60-317-010 TERMINAL, 1P MSC 2SC3052 KRC102
<10EZ,12EZ,17EZ,10K> CMBT5401 KRC104
T182 87-A60-317-010 TERMINAL, 1P MSC
<10EZ,12EZ,17EZ,10K> CMBT5551
WH181 87-A90-460-010 HLDR,WIRE 2.5-7P
<10EZ,12EZ,17EZ,10K>

• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

13 14
WIRING-1 (MAIN: K, EZ)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

EZ,K EZ,K
12EZ

B EZ,K

1
EZ,K
16 9
1 8

5 EZ,K 12EZ
12EZ 4 1
V
MW/LW 14
11
5 8
LOOP
C EZ,K
EZ,K
EZ,K EZ,K

8 5
1 4
FM

V
75Ω L 30
(COAXIAL)
D G
R

EZ,K

24 13
1 12
E J602

R FB602

VIDEO/
AUX J602
L

EZ,K

K
15 16
SCHEMATIC DIAGRAM-1 (MAIN 1/2: K, EZ)

17 18
SCHEMATIC DIAGRAM-2 (MAIN 2/2: K, EZ)

19 20
WIRING-2 (MAIN: HR)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

<HR>
Q949
B J940 Q950 C956 TC943 Q941
MW LOOP 1

C954
2
TC941 D941
R957
4 3 1
R970
5
6 1 1 2
3
L952 D951 L953 6 4
5
3 3 4
C 2
Q942 4 1
1
MW 1 5 5 8

Q943
Q945
Q944 D

8 5
C470
C315 1 4

D
30
L
G
R

Q837

E J602 24 13

R 1 12

VIDEO
AUX J602

R69

C115

C116

C117
I

R176

K
21 22
SCHEMATIC DIAGRAM-3 (MAIN 1/2: HR)

F2
F1

23 24
SCHEMATIC DIAGRAM-4 (MAIN 2/2: HR)

R964
33

25 26
WIRING-3 (MAIN: LH)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

K
27 28
SCHEMATIC DIAGRAM-5 (MAIN 1/2: LH)

29 30
SCHEMATIC DIAGRAM-6 (MAIN 2/2: LH)

31 32
WIRING-4 (FRONT)
1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 5 10 15 20 25 30 35 40 45

C 41 40

25

D301 D302 D303 D304 D305

64 24
EZ/K
12EZ
65
HR
D LH
: MOUNT
: NO MOUNT

80 1

H
12EZ MODEL

K
33 34
SCHEMATIC DIAGRAM-7 (FRONT)

D301 D302 D303 D304 D305

EZ/K
12EZ
12EZ MODEL HR
LH

100

HR MODEL
10

OTHER
MODELS

0.1

0.1
LH MODEL
33k

1k

22k
# : NO MOUNT

35 36
WIRING-5 (PT: K, EZ) SCHEMATIC DIAGRAM-8 (PT: K, EZ)
1 2 3 4 5 6 7

<K/EZ>
B

TO A MAIN C.B WH001

C

AC 230V
50Hz

AC 230V
50Hz
I

K
37 38
WIRING-6 (PT: HR) SCHEMATIC DIAGRAM-9 (PT: HR)
1 2 3 4 5 6 7

TO A MAIN C.B WH001

4
D 9
3 8

7
2
6

1 5

PT1

F
5 17

16
4
15

3 14

13
G 2
12

1 11

AC 120V
I 220V/230V/240V
50/60Hz

K
39 40
WIRING-7 (PT: LH) SCHEMATIC DIAGRAM-10 (PT: LH)
1 2 3 4 5 6 7

C PT C.B <LH>
B

TO A MAIN C.B CNA001

D

PT1

6
F

5 17

16
4
15
3
14
G
2 13

1 12

11

I AC 120V
220V/230V/240V
50/60Hz

K
41 42
WIRING-8 (DECK) FL (10-BT-224GNK) GRID ASSIGNMENT/ANODE CONNECTION
1 2 3 4 5 6 7 GRID ASSIGNMENT

K
43 44
ANODE CONNECTION

45
IC BLOCK DIAGRAM
IC, LC72131D

IC, M62495AFP

46
IC, LA1843/LA1844L-A

AM AGC/FM S-METER

PILOT CANCEL
AM OSC OUT

AM DET OUT

FM DET OUT
AM RF-IN
S-CURVE
AM LO

R-OUT

L-OUT
DET
PLL
24 23 22 21 20 19 18 17 16 15 14 13

ALC
AM AM AM
OSC MIX RF. AMP
BUFF DECODER PILOT
AGC ANTI-BIRDIE CANCEL

AM AM P-DET STEREO
IF DET Ø SW

LEVEL AM/FM
DET
S-CURVE IF COMP
BUFF VCO FF FF π FF PILOT
304kHz 38k 19k 2 19k DEL
TUNING
FM
FM DRIVE
IF
DET

REG GND
Vc

1 2 3 4 5 6 7 8 9 10 11 12
FM IN

AM MIX OUT

REG

AM-IN

GND

TUNE

ST

FM-DET

VCC

IF OUT

FM/AM

MONO
IC, BU1920FS

FO CMP
4 3
100kΩ
MUX 1
100kΩ

100kΩ

8TH SWITCHED
CAPACITOR FILTER

13 ARI

Vref 2

10 RCLK
VDD 14

RESET 16 12 QUAR

PLL PLL BI-PHASE DIFFERENTIAL 11 RDATA

57kHz 1187.5HZ
VSS 5 DECODER DECODER
RDS/ARI

REFERENCE 9 T57
TEST CIRCUIT
CLOCK

8 7 6 15

XI XO T1 T2

47
ELECTRICAL ADJUSTMENT-1 (K, EZ)

A MAIN C.B
%$#@098653 1 9 6 9 45
L801
L802 TC942
TP4 (DC BAL)
1 L941 5
IC801 L951
24 L942
TP3
IC301
1
TP2 (DC BAL)
(CLK)
3
TP8 (LCH)
GND TP1 (VT)
TP9 (RCH) FFE831
2
4
7

DECK–1 R/P/E, DECK-2 P HEAD

!
FWD
B FRONT C.B ^

TP5
IC101
L101
^

48
< TUNER SECTION > < DECK SECTION >
1. Clock Frequency Check 10. Tape Speed Adjustment (DECK 1)
Settings: • Test point: TP2 (CLK) Settings: • Test tape: TTA-100
Method: Set to MW 1602kHz and check that the test point • Test point: TP8 (Lch), TP9 (Rch)
is 2052kHz±45Hz. • Adjustment location: SFR701
Method: Play back the test tape and adjust SFR701 so that
2. MW VT Check the frequency counter reads 3000Hz±5Hz.
Settings: • Test point: TP1 (VT)
Method: Set to MW 1602kHz and check that the test point 11. Head Azimuth Adjustment (DECK 1, DECK 2)
is less than 8.0V. Then set to MW 531kHz and Settings: • Test tape: TTA-330
check that the test point is more than 0.6V. • Test point: TP8 (Lch), TP9 (Rch)
• Adjustment location: Head azimuth adjustment
3. MW Tracking Adjustment screw
Settings: • Test point: TP8 (Lch), TP9 (Rch) Method: Play back (FWD) the 8kHz signal of the test tape
• Adjustment location: L951 (1/3) and adjust screw so that the output becomes
Method: Set to MW 999kHz and adjust L951 (1/3) so that maximum.
the test point becomes maximum. Next, perform on REV PLAY mode.

4. LW VT Adjustment 12. PB Frequency Response Check (DECK 1, DECK 2)

Settings: • Test point: TP1 (VT) Settings: • Test tape: TTA-330
• Adjustment location: L942 • Test point: TP8 (Lch), TP9 (Rch)
Method: Set to LW 144kHz and adjust L942 so that the Method: Play back the 315Hz and 8kHz signals of the test
test point becomes 1.3V±0.05V. tape and check that the output ratio of the 8kHz
Then set to LW 290kHz and check that the test signal with respect to that of the 315Hz signal is
point is less than 8.0V. within 4dB.

5. LW Tracking Adjustment 13. PB Sensitivity Check (DECK 1, DECK 2)

Settings: • Test point: TP8 (Lch), TP9 (Rch) Settings: • Test tape: TTA-200
• Adjustment location: • Test point: TP8 (Lch), TP9 (Rch)
L941 ....................................................................... 144kHz Method: Play back the test tape and check that the output
TC942 ..................................................................... 290kHz level of the test point is 110mV±3.5dB.
Method: Set up TC942 to center before adjustment.
The level at 144kHz is adjusted to maximum by 14. REC/PB Frequency Response Check (DECK 1)
L941. Then the level at 290kHz is adjusted to Settings: • Test tape: TTA-602
maximum by TC942. • Test point: TP8 (Lch), TP9 (Rch)
• Input signal: 1kHz/8kHz (LINE IN)
6. AM IF Adjustment Method: Apply a 1kHz signal and REC mode. Then adjust
Settings: • Test point: TP8 (Lch), TP9 (Rch) OSC attenuator so that the output level at the test
• Adjustment location: points becomes -20VU. Record and play back
L802 ....................................................................... 450kHz the 1kHz and 8kHz signals and check that the
output of the 8kHz signals is 0dB±5dB with
7. FM VT Check respect to that of the 1kHz signal.
Settings: • Test point: TP1 (VT)
Method: Set to FM 108.0MHz and check that the test point 15. REC/PB Sensitivity Check (DECK 1)
is less than 8.0V. Then set to FM 87.5MHz and Settings: • Test tape: TTA-602
check that the test point is more than 0.5V. • Test point: TP8 (Lch), TP9 (Rch)
• Input signal: 1kHz (LINE IN)
8. FM Tracking Check Method: Apply a 1kHz signal and REC mode. Then adjust
Settings: • Test point: TP8 (Lch), TP9 (Rch) OSC attenuator so that the output level at TP8,
Method: Set to FM 98.0MHz and check that the test point TP9 becomes 0VU. Record and play back the
is less than 13dBµV. 1kHz signals and check that the output is
-2dB±3.5dB.
9. DC Balance/Mono Distortion Adjustment
Settings: • Test point: TP3, TP4 (DC balance)
TP8 (Lch), TP9 (Rch) (Distortion)
< FRONT SECTION >
• Adjustment location: L801 16. u-CON OSC Adjustment
• Input level: 60dBµV Settings: • Test point: TP5
Method: Set to FM 98.0MHz and adjust L801 so that the • Adjustment location: L101
voltage between TP3 and TP4 becomes Method: Insert AC plug with pressing of TUNER function
0V±0.04V. key and POWER key. Adjust L101 so that the
Next, check that the distortion is less than 1.3%. frequency across the test point is
58.350Hz±0.02Hz.

49
ELECTRICAL ADJUSTMENT-2 (HR)

A MAIN C.B
%$#@098653 1 9 6 94 3 5
L801
L802 TC943
TP4(DC BAL) TC941
1 L941
5
IC801
24 L942
TP3
IC301
1
TP2 (DC BAL)
(CLK) L953 L952
3
TP8 (LCH)
GND TP1 (VT)
TP9 (RCH)
FFE831
2
4
7

DECK–1 R/P/E, DECK-2 P HEAD

!
FWD
B FRONT C.B ^

TP5
IC101
L101
^

50
< TUNER SECTION > < DECK SECTION >
1. Clock Frequency Check 10. Tape Speed Adjustment (DECK 1)
Settings: • Test point: TP2 (CLK) Settings: • Test tape: TTA-100
Method: Set to MW 1602kHz and check that the test point • Test point: TP8 (Lch), TP9 (Rch)
is 2052kHz±45Hz. • Adjustment location: SFR701
Method: Play back the test tape and adjust SFR701 so that
2. MW VT Check the frequency counter reads 3000Hz±5Hz.
Settings: • Test point: TP1 (VT)
Method: Set to MW 1602kHz and check that the test point 11. Head Azimuth Adjustment (DECK 1, DECK 2)
is less than 8.0V. Then set to MW 531kHz and Settings: • Test tape: TTA-330
check that the test point is more than 0.6V. • Test point: TP8 (Lch), TP9 (Rch)
• Adjustment location: Head azimuth adjustment
3. MW Tracking Adjustment screw
Settings: • Test point: TP8 (Lch), TP9 (Rch) Method: Play back (FWD) the 8kHz signal of the test tape
• Adjustment location: and adjust screw so that the output becomes
L952 ....................................................................... 603kHz maximum.
TC941 ................................................................... 1404kHz Next, perform on REV PLAY mode.
Method: Set up TC941 to center before adjustment.
The level at 603kHz is adjusted to maximum by 12. PB Frequency Response Check (DECK 1, DECK 2)
L952. Then the level at 1404kHz is adjusted to Settings: • Test tape: TTA-330
maximum by TC941. • Test point: TP8 (Lch), TP9 (Rch)
Method: Play back the 315Hz and 8kHz signals of the test
4. SW VT Adjustment tape and check that the output ratio of the 8kHz
Settings: • Test point: TP1 (VT) signal with respect to that of the 315Hz signal is
• Adjustment location: L942 within 4dB.
Method: Set to SW 5.73MHz and adjust L942 so that the
test point becomes 1.3V±0.05V. 13. PB Sensitivity Check (DECK 1, DECK 2)
Then set to SW 17.9MHz and check that the test Settings: • Test tape: TTA-200
point is less than 8.0V. • Test point: TP8 (Lch), TP9 (Rch)
Method: Play back the test tape and check that the output
5. SW Tracking Adjustment level of the test point is 110mV±3.5dB.
Settings: • Test point: TP8 (Lch), TP9 (Rch)
• Adjustment location: 14. REC/PB Frequency Response Check (DECK 1)
L941 ...................................................................... 5.73kHz Settings: • Test tape: TTA-602
TC943 .................................................................... 17.9kHz • Test point: TP8 (Lch), TP9 (Rch)
Method: Set up TC943 to center before adjustment. • Input signal: 1kHz/8kHz (LINE IN)
The level at 5.73kHz is adjusted to maximum by Method: Apply a 1kHz signal and REC mode. Then adjust
L941. Then the level at 17.9kHz is adjusted to OSC attenuator so that the output level at the test
maximum by TC943. points becomes -20VU. Record and play back
the 1kHz and 8kHz signals and check that the
6. AM IF Adjustment output of the 8kHz signals is 0dB±5dB with
Settings: • Test point: TP8 (Lch), TP9 (Rch) respect to that of the 1kHz signal.
• Adjustment location:
L802 ....................................................................... 450kHz 15. REC/PB Sensitivity Check (DECK 1)
Settings: • Test tape: TTA-602
7. FM VT Check • Test point: TP8 (Lch), TP9 (Rch)
Settings: • Test point: TP1 (VT) • Input signal: 1kHz (LINE IN)
Method: Set to FM 108.0MHz and check that the test point Method: Apply a 1kHz signal and REC mode. Then adjust
is less than 8.0V. Then set to FM 87.5MHz and OSC attenuator so that the output level at TP8,
check that the test point is more than 0.5V. TP9 becomes 0VU. Record and play back the
1kHz signals and check that the output is
8. FM Tracking Check -2dB±3.5dB.
Settings: • Test point: TP8 (Lch), TP9 (Rch)
Method: Set to FM 98.0MHz and check that the test point
is less than 9dBµV.
< FRONT SECTION >
16. u-CON OSC Adjustment
9. DC Balance/Mono Distortion Adjustment Settings: • Test point: TP5
Settings: • Test point: TP3, TP4 (DC balance) • Adjustment location: L101
TP8 (Lch), TP9 (Rch) (Distortion) Method: Insert AC plug with pressing of TUNER function
• Adjustment location: L801 key and POWER key. Adjust L101 so that the
• Input level: 60dBµV frequency across the test point is
Method: Set to FM 98.0MHz and adjust L801 so that the 58.350Hz±0.02Hz.
voltage between TP3 and TP4 becomes
0V±0.04V.
Next, check that the distortion is less than 1.2%.

51
ELECTRICAL ADJUSTMENT-3 (LH)

A MAIN C.B
#@!0987643 1 7 4 7
L801
L802 TP4 (DC BAL)
1
IC801 L951
24
TP3
IC301
1
TP2 (DC BAL)
(CLK)
3
TP8 (LCH)
GND TP1 (VT)
TP9 (RCH)
FFE831
2
5

DECK–1 R/P/E, DECK-2 P HEAD

9
FWD
B FRONT C.B $

TP5
IC101
L101
$

52
< TUNER SECTION > 10. PB Frequency Response Check (DECK 1, DECK 2)
Settings: • Test tape: TTA-330
1. Clock Frequency Check
• Test point: TP8 (Lch), TP9 (Rch)
Settings: • Test point: TP2 (CLK)
Method: Play back the 315Hz and 8kHz signals of the test
Method: Set to AM 1602kHz and check that the test point
tape and check that the output ratio of the 8kHz
is 2052kHz±45Hz.
signal with respect to that of the 315Hz signal is
within 4dB.
2. AM VT Check
Settings: • Test point: TP1 (VT)
11. PB Sensitivity Check (DECK 1, DECK 2)
Method: Set to AM 1602kHz and check that the test point
Settings: • Test tape: TTA-200
is less than 8.0V. Then set to AM 531kHz and
• Test point: TP8 (Lch), TP9 (Rch)
check that the test point is more than 0.6V.
Method: Play back the test tape and check that the output
level of the test point is 110mV±3.5dB.
3. AM Tracking Adjustment
Settings: • Test point: TP8 (Lch), TP9 (Rch)
12. REC/PB Frequency Response Check (DECK 1)
• Adjustment location: L951 (1/3)
Settings: • Test tape: TTA-602
Method: Set to MW 999kHz and adjust L951 (1/3) so that
• Test point: TP8 (Lch), TP9 (Rch)
the test point becomes maximum.
• Input signal: 1kHz/8kHz (LINE IN)
Method: Apply a 1kHz signal and REC mode. Then adjust
4. AM IF Adjustment
OSC attenuator so that the output level at the test
Settings: • Test point: TP8 (Lch), TP9 (Rch)
points becomes -20VU. Record and play back
• Adjustment location:
the 1kHz and 8kHz signals and check that the
L802 ....................................................................... 450kHz
output of the 8kHz signals is 0dB±5dB with
respect to that of the 1kHz signal.
5. FM VT Check
Settings: • Test point: TP1 (VT)
13. REC/PB Sensitivity Check (DECK 1)
Method: Set to FM 108.0MHz and check that the test point
Settings: • Test tape: TTA-602
is less than 8.0V. Then set to FM 87.5MHz and
• Test point: TP8 (Lch), TP9 (Rch)
check that the test point is more than 0.5V.
• Input signal: 1kHz (LINE IN)
Method: Apply a 1kHz signal and REC mode. Then adjust
6. FM Tracking Check
OSC attenuator so that the output level at TP8,
Settings: • Test point: TP8 (Lch), TP9 (Rch)
TP9 becomes 0VU. Record and play back the
Method: Set to FM 98.0MHz and check that the test point
1kHz signals and check that the output is
is less than 9dBµV (V model: 8dBµV).
-2dB±3.5dB.
7. DC Balance/Mono Distortion Adjustment
Settings: • Test point: TP3, TP4 (DC balance) < FRONT SECTION >
TP8 (Lch), TP9 (Rch) (Distortion)
14. u-CON OSC Adjustment
• Adjustment location: L801
Settings: • Test point: TP5
• Input level: 60dBµV
• Adjustment location: L101
Method: Set to FM 98.0MHz and adjust L801 so that the
Method: Insert AC plug with pressing of TUNER function
voltage between TP3 and TP4 becomes
key and POWER key. Adjust L101 so that the
0V±0.04V.
frequency across the test point is
Next, check that the distortion is less than 1.2%.
58.350Hz±0.02Hz.

< DECK SECTION >

8. Tape Speed Adjustment (DECK 1)
Settings: • Test tape: TTA-100
• Test point: TP8 (Lch), TP9 (Rch)
• Adjustment location: SFR701
Method: Play back the test tape and adjust SFR701 so that
the frequency counter reads 3000Hz±5Hz.

9. Head Azimuth Adjustment (DECK 1, DECK 2)

Settings: • Test tape: TTA-330
• Test point: TP8 (Lch), TP9 (Rch)
• Adjustment location: Head azimuth adjustment
screw
Method: Play back (FWD) the 8kHz signal of the test tape
and adjust screw so that the output becomes
maximum.
Next, perform on REV PLAY mode.

53
IC DESCRIPTION
IC, M38B57MCH-E236FP/M38B59MFH-E250FP
Pin No. Pin Name I/O Description
1 I-SIG I RDS signal level A/D input. (Not used)
2 I-HOLD I Hold voltage level A/D input.
3 I-SW (CD) I CD mecha SW A/D input.
4 I-DISH I CD turn-table position check A/D input.
5 I-KEY2 I KEY2 A/D input.
6 I-KEY1 I KEY1 A/D input.
I-RDS-DATA/
7 I/O RDS data input / DSP IC data (V-CD) output. (Not used) (O-DSP_DATA)
(O-DSP_DATA)
8 O-MOTOR O Deck motor supply ON/OFF output.
9 I-RMC I System remote control signal input. (“L”=ACTIVE)
10 RESET I System reset input. (“L”=RESET)
11 I-STERE I Tuner stereo input. (“L”=STEREO)
12 O-DSC/O-PLL_DATA O Function IC control & PLL data output.
13 VSS — GND.
14, 15 XIN, XOUT I/O 4.19MHz system CLK input / output.
16 VCC — Power supply input.
17 O-PB1 O Deck 1/2 switch output. (“L”=PLAYBACK DECK 1)
18 O-STBY O Standby LED ON/OFF output. (“L”=ON)
19 O-RMT O REC mute output. (“H”=MUTE)
20 O-BIAS O Record bias ON/OFF output. (“L”=ON)
21 O-TU_ON O Tuner supply ON/OFF output. (“H”=ON)
22 O-CD_ON O CD supply ON/OFF output. (“H”= ON)
23 O-C.SHIFT O MICON clock shift output. (“L”=SHIFT)
24 O-PLL-CLK O PLL IC CLK output.
25 I-TM_BASE I 8 Hz time base input.
26 O-CLOSE O CD door close output.
27 O-CD-OPEN O CD door open output.
28 VEE — Power supply input for FL display.
29 O-STB(DSP) O DSP IC strobe output. (Not used)
30 K-SCAN O Initial key scan output.
31 O-PLL_CE O CD PLL IC chip enable output.
32 O-CD_LED O CD flash window LED output.
33-42 G10~G1 O FL grid output (G10~G1).
43 P22 O FL segment output (P22). (Not used)
44-58 P21-P7 O FL segment output (P21~P7).
59 PHONO/P6 I/O PHONO diode input / FL segment output (P6).
60 CASINO DEMO/P5 I/O CASINO DEMO diode input (Not used) / FL segment output (P5).
61 NON-ECO/P4 I/O ECO OFF diode input / FL segment output (P4).
62 I-TU3/P3 I/O TU 3 diode input (Not used) / FL segment output (P3).
63 I-TU2/P2 I/O TU 2 diode input (Not used) / FL segment output (P2).
64 I-TU1/P1 I/O TU 1 diode input (Not used) / FL segment output (P1).

54
Pin No. Pin Name I/O Description
65 O-DISH_R O CD turn-table reverse turn output.
66 O-DISH_F O CD turn-table forward turn output.
67 I-SUBQ I Sub code-Q data input.
68 O-CD_CE O CD DSP chip enable output.
69 I-WRQ I CD WRQ input.
70 O-CLK (CD) O CD control clock output .
71 O-DATA (CD) O CD control data output.
72 I-TUNE/IFC I Tuner SD input / IF count input.
73 AVSS — GND.
74 VREF — Reference voltage.
75 I-DRF I CD DRF input.
76 I-RDS_CLK I RDS clock input. (Not used)
77 I-LEVEL I Connected to GND through a resistor.
78 O-POWER O SYSTEM Power ON/OFF output. (“H”=ON)
79 I-RE_VOL I Rotary encoder A/D input.
80 I-TP_SW I Deck mecha SW A/D input.

55
MECHANICAL PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 82-NF7-218-010 SPR-T,CASS 25 8A-NFA-064-010 PANEL,TOP V-2 B<17EZBM>
2 8A-NFA-004-010 BOX,CASS 2<EXCEPT 17EZBM> 26 8A-NFA-063-010 PANEL,LEFT V-2<EXCEPT 17EZBM>
2 8A-NFA-048-010 BOX,CASS 2 BLK<17EZBM> 26 8Z-NFA-035-110 PANEL,LEFT V-2 B<17EZBM>
3 8A-NFA-003-010 BOX,CASS 1<EXCEPT 17EZBM> 27 8A-NFA-215-010 PLATE,PL HR<10HR>
3 8A-NFA-047-010 BOX,CASS 1 BLK<17EZBM> 28 84-ZG1-245-210 CAP,OPTICAL

4 8A-NFA-007-010 WINDOW,CASS 2<EXCEPT 17EZBM> 29 8A-NFA-029-010 CABI,REAR EZBM SZ17<17EZBM>

4 8A-NFA-072-010 WINDOW,CASS 2 BLK<17EZBM> 29 8A-NFA-024-010 CABI,REAR EZSM<10EZSM>
5 8A-NFA-006-010 WINDOW,CASS 1<EXCEPT 17EZBM> 29 8A-NFA-025-010 CABI,REAR EZSM SZ12<12 EZSM>
5 8A-NFA-071-010 WINDOW,CASS 1 BLK<17EZBM> 29 8A-NFA-022-010 CABI,REAR HRJSM<10HR>
6 87-CE3-023-010 BADGE,AIWA 30N SILV 29 8A-NFA-026-010 CABI,REAR KSM<10KSM>

7 8A-NFA-054-010 WINDOW,DISP EZ SZ12<12 EZSM> 29 8A-NFA-030-010 CABI,REAR LH W/O SPEC<11LHSC>

7 8A-NFA-059-010 WINDOW,DISP EZ SZ17<17EZBM> 30 88-906-251-110 FF-CABLE,6P 1.25
7 8A-NFA-051-010 WINDOW,DISP H 31 8A-NF8-205-010 HLDR,IC<11LHSC>
<EXCEPT 17EZBM,12 EZSM> 32 8A-NFA-214-010 HLDR,PWB M ANFA<11LHSC>
8 8A-NFA-011-010 KNOB,RTRY VOL<EXCEPT 17EZBM> 33 8A-NFA-065-010 PANEL,RIGHT V-2<10HR,11LHSC>
8 8A-NFA-055-010 KNOB,RTRY VOL BLK<17EZBM>
33 8A-NFA-068-010 PANEL,RIGHT V-2 B PL<17EZBM>
9 8A-NFA-012-010 RING,VOL 33 8A-NFA-067-010 PANEL,RIGHT V-2 PL
10 8Z-NF8-028-110 KNOB,RTRY MIC<10HR> <10KSM,10EZSM,12 EZSM>
11 81-532-080-010 LBL,CASS-COMPT<17EZBM> 34 8A-NF9-211-010 HLDR,PWB PT HI
12 86-NFZ-231-010 DMPR,70 35 88-NF9-213-010 HLDR,PWB MAIN<EXCEPT 11LHSC>
13 8A-NFA-042-010 CABI,FR EZ<12 EZSM> 36 87-NF4-221-010 HLDR,CABLE<EXCEPT 11LHSC>

13 8A-NFA-044-010 CABI,FR EZ BLK<17EZBM> 37 8Z-NB8-240-010 COVER, PL

13 8A-NFA-041-010 CABI,FR H<10HR> ! 38 87-085-185-010 BUSHING, AC CORD (E)
13 8A-NFA-001-010 CABI,FR U<10KSM,10EZSM,11LHSC> ! 39 87-A80-157-010 AC CORD ASSY,E BLK CC
14 8A-NFA-014-010 KEY,CASS 2P<EXCEPT 17EZBM> 40 8A-NFA-212-010 PLATE,PL LH<11LHSC>
14 8A-NFA-020-010 KEY,CASS 2P BLK<17EZBM> A 87-067-703-010 TAPPING SCREW, BVT2+3-10

15 8A-NFA-013-010 KEY,CASS 1<EXCEPT 17EZBM> B 87-NF4-224-010 S-SCREW,IT3B+3-8 CU

15 8A-NFA-019-010 KEY,CASS 1 BLK<17EZBM> C 87-078-191-010 S-SCREW,IT+4-10
16 8A-NFA-010-010 KEY,OPE<EXCEPT 17EZBM> D 87-723-096-410 QT2+3-10W/O SLOT BL<11LHSC>
16 8A-NFA-057-010 KEY,OPE BLK<17EZBM> E 87-721-096-410 QT2+3-10 GLD<11LHSC>
17 8A-NF9-021-010 PLATE,MIC<10HR> F 87-067-641-010 UTT2+3-8(W/O SLOT)BL

18 8A-NFA-009-010 KEY,FUN<EXCEPT 17EZBM> G 87-721-097-410 QT2+3-12 GLD

18 8A-NFA-056-010 KEY,FUN BLK<17EZBM> H 87-067-581-010 TAPPING SCREW, BVT2+3-15<11LHSC>
19 8A-NFA-016-010 KEY,RDS<12 EZSM> I 87-067-688-010 BVTT+3-6
20 8A-NFA-018-010 REFLECTOR,ECO
21 8A-NFA-008-010 KEY,POWER

22 8A-NFA-208-010 GUIDE,FL 100-25 ANFA

23 8A-NFA-049-010 PANEL,TRAY BLK<17EZBM>
23 8A-NFA-002-010 PANEL,TRAY H<EXCEPT 17EZBM>
24 88-913-221-110 FF-CABLE, 13P 1.25 220MM
25 8A-NFA-062-010 PANEL,TOP V-2<EXCEPT 17EZBM>

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink

56
MECHANICAL EXPLODED VIEW 1/1

25

A
28

A A
A
AZG-1

27

26
29
24 31
A
A F
A
19 22 H
23 FL A A
21 30
A 32 B
18
20 LHSC2M
G
P.C.B HT-SINK
A
D
ZZM-2 A P.C.B
6 P.C.B
16 A F A
A C C
G
33
17 LHSC2M
A F
7 A 40
HLDR1 HT-SINK
9 PLATE EARTH 34
3 5 HLDR2 A HRJSM/
MECHA HRJSM PT
8 LHSC2M
4 A
A
36 F
C
15 35 I 39 C

14 38
10 11 13 34
B E
2 PT
PLATE EARTH MIC C
1 12 P.C.B

BINDER
1 WIRE CHAS, MAIN

A
37

57 58
TAPE MECHANISM EXPLODED VIEW 1/1 (ZZM-2 PR1NM/PR1NO/YPR1NM)

54 TERMINAL,LB1 A

4 22
14 TERMINAL,LB1 A
55
15
21 23 22
3 28 20
13
19 21 23
6 27
5 20
2 18 14
b 54
29
17 25 15
1 6
13 5 a
55 31
59 24 26
19
16
28
18 59
61
17 30

B 16
53 47 29
46 38 27
25
45 33 26
37 24
44

43 34
b
1

12 51
a
11 40 53
12 32
33
52 34
10 4
51
3 11 47
1
9 36
39 37
2 50 46 35
8
45
1 10 56
7
44
57 9 49 38
8 48 43
58
7 40
41
57 62
39
58

59 60
TAPE MECHANISM PARTS LIST 1/1 (ZZM-2 PR1NM/PR1NO/YPR1NM)

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 8Z-ZM1-254-210 SPR-C,REEL R 36 8Z-ZM1-220-110 LEVER,REC SENSOR
2 8Z-ZM1-225-110 GEAR,REEL R 37 8Z-ZM1-249-010 SPR-T,FR
3 8Z-ZM1-253-110 SPR-C,AUTO SENSOR 38 8Z-ZM1-242-110 SPR-T,FF/REW
4 8Z-ZM1-217-110 LEVER,AUTO SENSOR 39 8Z-ZM1-229-010 GEAR,CAM
5 8Z-ZM1-212-110 LEVER,T-UP 40 8Z-ZM1-232-010 GEAR,IDL FF/REW

6 8Z-ZM1-245-010 SPR-T,AUTO 41 8Z-ZM1-290-010 FLY-WHL ASSY,ZZM-1

7 8Z-ZM1-236-010 CLR,SLIP FF/REW
8 8Z-ZM1-252-010 SPR-C,FF/REW 43 8Z-ZM1-228-010 GEAR,SLIP T-UP B
9 8Z-ZM1-230-010 GEAR,SLIP FF/REW A 44 8Z-ZM1-265-010 FELT,T-UP
10 8Z-ZM1-269-010 FELT,FF/REW 2 45 8Z-ZM1-227-010 GEAR,SLIP T-UP A

11 8Z-ZM1-238-110 GEAR,SLIP FF/REW B 2 46 8Z-ZM1-251-110 SPR-C,T-UP SLIP

12 8Z-ZM1-237-010 LEVER,FF/REW 2 47 8Z-ZM1-243-210 SPR-T,STOP/PAUSE
13 8Z-ZM1-209-210 LEVER,PAUSE 48 87-A91-532-010 MOT,MS15U2LW1A
14 8Z-ZM1-218-110 LEVER,E-LOCK H 49 8Z-ZM1-235-010 PULLEY,MOT
15 8Z-ZM1-256-010 SPR-P,PAUSE 50 8Z-ZM2-216-010 BELT,MAIN M

16 8Z-ZM1-244-010 SPR-T,T-UP 51 8Z-ZM1-260-010 SPR-P,CASETTE

17 8Z-ZM1-247-210 SPR-T,PINCH 52 8Z-ZM2-201-010 CHAS ASSY,ZZM-2
18 8Z-ZM1-261-110 ROLLER ASSY,PINCH 53 8Z-ZM1-255-110 SPR-T,E-LOCK
19 8Z-ZM1-221-010 LEVER,PINCH 54 8Z-ZM2-219-010 LEVER,E-OPEN ZZM-2
20 8Z-ZM1-205-210 LEVER,PLAY 55 8Z-ZM1-214-110 LEVER,LOCK

21 8Z-ZM1-248-110 SPR-T,BRG 56 8Z-ZM2-230-010 FLY-WHL ASSY,ZZM-2

22 87-A90-403-110 HEAD,RPH MS15R 57 8Z-ZM1-257-110 SPR-C,F/R
23 84-ZM2-227-310 SPR-C,AZIMUTH 58 8Z-ZM1-275-010 W-L,1.47-4-0.25
24 8Z-ZM1-216-010 LEVER,AUTO 59 80-ZM6-243-010 SH 1.75-3.6-0.5 SLT
25 8Z-ZM1-246-010 SPR-T,AUTO 2 60 87-A91-494-010 SW,LEAF MSW17820

26 8Z-ZM2-214-010 GEAR,IDL REW ZZM-2 61 8Z-ZM1-241-010 SPR-T,PLAY

27 8Z-ZM2-212-010 LEVER,STOP ZZM-2 62 8Z-ZM2-601-010 CONN ASSY,9P ZZM-2
28 8Z-ZM1-207-010 LEVER,FF A 84-ZM2-242-010 S-SCREW,AZ1-2-6.4
29 8Z-ZM1-206-010 LEVER,REW B 8Z-ZM2-220-110 V+2.6 ZZM-2
30 8Z-ZM1-210-010 LEVER,REC

31 87-A90-404-010 HEAD,EH LE15B

32 8Z-ZM2-218-010 LEVER,REC LOCK ZZM-2
33 87-A91-492-010 SW,LEAF MSW18560
34 8Z-ZM1-226-010 GEAR,REEL L
35 8Z-ZM1-241-010 SPR-T,PLAY

61
SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1 Type.4
Insert a flat-bladed screwdriver into the position indicated by the TOOLS
arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer
unit and then remove the speaker units.
2 (-) flat head screwdriver
3 Cut chisel

1 2 3

How to Remove the PANEL, FR

Type.2
1. Insert the (-) flat head screwdriver tip into the gap between
Remove the grill frame and four pieces of rubber caps by pulling the PANEL, FR and the PANEL, SPKR. Tap the head of
out with a flat-bladed screwdriver. Remove the screws from hole the (-) flat head screwdriver with the plastic hammer head,
where installed rubber caps. Insert a flat-bladed screwdriver into and create the clearance as shown in Fig-1.
the position indicated by the arrows and remove the panel. Remove
the screws of each speaker unit and then remove the speaker units. 2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.

3. Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.

Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclock-
wise direction while inserting a flat-bladed screwdriver into one of
the hollows around speaker unit, and then remove the speaker unit.
After replacing the speaker unit, install it turning to clockwise di- Fig-1 Fig-2
rection until "click" sound comes out.

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.

62
SPEAKER PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 8A-NSL-001-010 PANEL,FR<EXCEPT 10YB>
1 8A-NSL-012-010 PANEL,FR B<10YB>
2 8A-NSL-003-010 GRILLE,FRAME ASSY
3 8A-NSL-606-010 SPKR, W 120<10YS,10YB,12Y1S,12YS>
3 8A-NSL-604-010 SPKR, W 120<12YJ3S,12YJSC1>

3 8Z-NSL-603-010 SPKR, W 120<12YJSL,12YJSC>

3 8A-NSL-602-010 SPKR,120<15YLSC>
4 8A-NSL-017-010 CORD,SPKR
<12Y1S,12YS,12YJ3S,15YLSC>
4 87-NS7-611-010 CORD,SPKR
<EXCEPT 12Y1S,12YS,12YJ3S>
5 8Z-NSY-003-010 CORD,BUSH<15YLSC>

ACCESSORIES/PACKAGE LIST

REF. NO PART NO. KANRI DESCRIPTION

NO.
1 8A-NFA-906-010 IB,EZ(9L)M PDF
<10EZ,17EZ>
1 8A-NFA-916-010 IB,EZ(9L)M -SZ12(RDS) PDF
<12EZ>
1 8A-NFA-901-110 IB,H(ECA)M<10HR>
1 8A-NFA-905-010 IB,K(E)M PDF
<10K>
1 8A-NFA-929-010 IB,LH(P)CCE -SZ10J<11LHSC2>

! 2 87-A91-017-010 PLUG,CONVERSION JT-0476<10HR>

3 8Z-NF9-701-210 RC UNIT,ZAS02<EXCEPT 17EZ>
3 8Z-NF9-703-110 RC UNIT,ZAS17<17EZ>
4 87-006-225-010 AM LOOP ANT NC2<EXCEPT 10HR>
4 87-006-226-010 AM-LOOPANT C0<10HR>

5 87-043-115-010 ANT,FEEDER FM<10HR,11LHSC2>

6 87-A90-118-010 ANT,WIRE FM (Z)
<10EZ,12EZ,17EZ,10K>
7 87-A90-119-010 ANT,WIRE SW(5M)<10HR>

63
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
920074 Printed in Singapore