Scribd Logo
Upload

Welcome to Scribd!

  • 38 views

    General Data For Project 1: Head Regulator Irrigation Works Design

    Uploaded by

    khaaled
    The document provides general design data for 7 head regulator projects, including discharge rates, bridge dimensions, soil properties, and load specifications. For each project, the tasks are to conduct the hydraulic design of the regulator and provide a complete structure design. Missing data should be reasonably assumed. The document was produced by Dr. Amir Mobasher of Al-Azhar University's Faculty of Engineering for an irrigation works design course.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    General Data For Project 1: Head Regulator Irrigation Works Design

    Uploaded by

    khaaled
    38 views7 pages
    The document provides general design data for 7 head regulator projects, including discharge rates, bridge dimensions, soil properties, and load specifications. For each project, the tasks are to conduct the hydraulic design of the regulator and provide a complete structure design. Missing data should be reasonably assumed. The document was produced by Dr. Amir Mobasher of Al-Azhar University's Faculty of Engineering for an irrigation works design course.

    Original Title

    Regulator Projects

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides general design data for 7 head regulator projects, including discharge rates, bridge dimensions, soil properties, and load specifications. For each project, the tasks are to conduct the hydraulic design of the regulator and provide a complete structure design. Missing data should be reasonably assumed. The document was produced by Dr. Amir Mobasher of Al-Azhar University's Faculty of Engineering for an irrigation works design course.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    38 views7 pages

    General Data For Project 1: Head Regulator Irrigation Works Design

    Uploaded by

    khaaled
    The document provides general design data for 7 head regulator projects, including discharge rates, bridge dimensions, soil properties, and load specifications. For each project, the tasks are to conduct the hydraulic design of the regulator and provide a complete structure design. Missing data should be reasonably assumed. The document was produced by Dr. Amir Mobasher of Al-Azhar University's Faculty of Engineering for an irrigation works design course.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    Irrigation works design (2) Head Regulator

    General Data for Project 1


    Figure (1) shows the D.S cross section of a main canal in which a
    reinforced concrete regulator is to be constructed. The regulator
    consists of 4 vents each 3.0 m width. The maximum discharge through
    the regulator is Q = 50 m3/sec and the maximum heading up is 10 cm.
    The following data are also considered in the design:
    i. The bridge width = 10.0 m and it has 2 sidewalks of 1.0 m each.
    ii. The pier width =1.0 m, Vertical sliding steel gates with four Main
    girders are used.
    iii. The equivalent Dead and Live loads of the bridge are 1.00 and
    3.00 t/m2, respectively.
    iv. The soil properties at the regulator site are: Φ = 30o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.15 kg/cm2.
    v. (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    a) Check the value of heading up for fully open gates.
    b) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 1 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 2


    A reinforced concrete head regulator with approach channel is to be
    constructed to feed a main canal from a Rayah. The cross section for
    the canal is shown in figure (1). The available data for the regulator
    are:
    i. The equivalent D.L of the bridge and sidewalks =1.0 t/m2.
    ii. The equivalent L.L on the bridge is assumed uniformly distributed
    and equal 1.5 t/m2 while for the sidewalks is considered of 0.5
    t/m2.
    iii. The bridge width over the regulator is 10.0 m and has two
    sidewalks of 1.25 m width for each.

    iv. Width of the piers and abutments = 0.8 m


    v. The soil properties at the regulator site are: Φ = 35o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.20 kg/cm2.
    vi. (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    a) Give a complete hydraulic design of the regulator.
    b) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 2 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 3


    A reinforced concrete head regulator with 200.0 m approach channel
    is to be constructed to feed a main canal from a Rayah. The cross
    sections data for the canal and Rayah at the crossing site are given in
    the following table. The available data for the regulator are:
    i. Maximum allowable discharge through the canal is 6.8*106
    m3/day.
    ii. The span of vents is 5.0 m, the bridge width over the regulator is
    10.0 m and it has two sidewalks of 1.0 m width for each,
    iii. The width of the intermediate piers is 1.0 m, Vertical sliding
    steel gates with three Main girders are used.
    iv. The equivalent Dead and Live loads of the bridge are 1.25 and
    2.50 t/m2, respectively.
    v. The soil properties at the regulator site are: Φ = 30o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.15
    kg/cm2. (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    a) Carry out the hydraulic design of the regulator
    b) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 3 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 4


    A reinforced concrete head regulator is to be constructed to feed a
    branch canal from a main canal. The cross sections data for the branch
    canal is given in the following table. The available data for the
    regulator are:
    i. Maximum allowable discharge through the canal is 65 m3/s.
    ii. The bridge width over the regulator is 10.0 m and it has two
    sidewalks of 1.0 m width for each,
    iii. The width of the intermediate piers is 1.25 m, Vertical sliding
    steel gates with four Main girders are used.
    iv. The equivalent Dead and Live loads of the bridge are 1.00 and
    2.50 t/m2, respectively.
    v. The soil properties at the regulator site are: Φ = 30o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.11 kg/cm2.
    (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    c) Carry out the hydraulic design of the regulator
    d) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 4 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 5


    Figure (1) shows the D.S cross section of a main canal in which a
    reinforced concrete regulator is to be constructed. The maximum
    discharge through the regulator is Q = 64 m3/sec and the maximum
    heading up is 10 cm. The following data are also considered in the
    design:
    i. The bridge width = 8.0 m and it has 2 sidewalks of 1.0 m each.
    ii. The pier width =1.0 m, Vertical sliding steel gates with four Main
    girders are used.
    iii. The equivalent Dead and Live loads of the bridge are 1.20 and
    2.30 t/m2, respectively.
    iv. The soil properties at the regulator site are: Φ = 35o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.20 kg/cm2.
    v. (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    c) Carry out the hydraulic design of the regulator
    d) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 5 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 6


    It is required to give a complete design of the regulator according to
    the following data:
    - Canal discharge Q = 24 m3 / sec
    - Canal bed level : 100.00
    - Bed width : 10 m
    - Road level : 104.50
    - Max water level : 103.50
    - Side slope : 3 : 2
    - Road Width : 12 m
    - Soil type :- medium clay (Soil strength = 1.5 kg / cm2)
    - The pier width =1.0 m, Vertical sliding steel gates with four Main
    girders are used.
    - The equivalent Dead and Live loads of the bridge are 1.50 and
    2.50 t/m2, respectively.
    - The soil properties at the regulator site are: Φ = 35o, γbulk = 1.80
    t/m3, void ratio 40 %. (For the used R.C, K1 = 0.31, K2 = 1218).

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 6 Dr. Amir Mobasher


    Irrigation works design (2) Head Regulator

    General Data for Project 7


    Figure (1) shows the D.S cross section of a main canal in which a
    reinforced concrete regulator is to be constructed. The maximum
    discharge through the regulator is Q = 26 m3/sec and the maximum
    heading up is 10 cm. The following data are also considered in the
    design:
    i. The bridge width = 8.0 m and it has 2 sidewalks of 1.25 m each.
    ii. The pier width =1.25 m, Vertical sliding steel gates with four
    Main girders are used.
    iii. The equivalent Dead and Live loads of the bridge are 1.00 and
    2.00 t/m2, respectively.
    iv. The soil properties at the regulator site are: Φ = 35o, γbulk = 1.80
    t/m3, void ratio 40 % and the soil bearing capacity = 1.00 kg/cm2.
    v. (For the used R.C, K1 = 0.31, K2 = 1218).

    It is required to:
    e) Carry out the hydraulic design of the regulator
    f) Give a complete structure design of the regulator.

    Note: any missing data to be reasonably assumed.

    Al-Azhar University-Faculty of Engineering 7 Dr. Amir Mobasher

    You might also like