PROJECT : Warehousing at Haringhata DATE:

SUBJECT : BILL OF QUANTITIES FOR PHE SYSTEM - INTERNAL PLUMBING WORKS Rev. No.:
COST SUMMARY
PART-1 DESCRIPTION Total

A SANITARY FIXTURES AND CP FITTINGS 7,401,672.39

B INTERNAL SEWAGE SYSTEM - SOIL & WASTE 4,642,468.01

C INTERNAL WATER SUPPLY SYSTEM - DOMESTIC, FLUSHING & HOT WATER 950,282.62

SUB TOTAL 12,994,423.02

PART-2 DESCRIPTION AMOUNT

D CIVIL WORKS 2,330,226.98

SUB TOTAL 2,330,226.98

GRAND TOTAL 15,324,650.00

ADITHI CONSULTANTS 1
 PROJECT : Warehousing at Haringhata, West Bengal
SUBJECT: BILL OF QUANTITIES FOR PHE SYSTEM - INTERNAL

A GENERAL NOTES:
I THIS BOQ IS AN INDICATIVE DOCUMENT AND IS TO BE USED AS A TENDERING AID ONLY. THE BOQ DOES NOT CONSTITUTE A WARRANTY
OR REPRESENTATION OF ANY KIND.
II
ALL THE BELOW MENTIONED ITEMS SHALL BE COMPLETED AS REQUIRED BY THE CLIENT / PROJECT -IN- CHARGE & AS PER THE TECHNICAL
SPECIFICATION

B PREAMBLES

All items of work under this Contract shall be executed strictly to fulfill the requirements laid down under “Basis of
Design” in the specifications. Type of equipment, material specification, methods of installation and testing and type of
control shall be in accordance with the specifications, approved shop drawings and the relevant Indian Standards,
1 however capacity of each component and their quantities shall be such as to fulfill the above mentioned requirement.

The unit rate for all equipment or materials shall include cost in INDIAN RUPEES (INR) for equipment and materials
including taxes and duties and also including forwarding, freight, insurance and transport into Contractor’s store at
2 site, storage, installation, testing, balancing, commissioning and other works required.

3 The rate for each item of work included in the Schedule of Quantities shall, unless expressly stated otherwise, include
cost of:
All materials, fixing materials, accessories, appliances tools, plants, equipment, transport, labor and incidentals
required in preparation for and in the full and entire execution, testing, balancing, commissioning and completion of
a) work called for in the item and as per Specifications and Drawings.

b) Wastage on materials and labor.

Loading, transporting, unloading, handling/double handling, hoisting to all levels, setting, fitting and fixing in position,
c) protecting, disposal of debris and all other labor necessary in and for the full and entire execution and or the job in
accordance with the contract documents, good practice and recognized principles.

d) Liabilities, obligations and risks arising out of Conditions of Contract.

All requirements of Specifications, whether such requirements are mentioned in the item or not. The Specifications and
Drawings where available, are to be read as complimentary to and part of the Bill of Quantities and any work called
e) for in one shall be taken as required for all.

In the event of conflict between Bill of Quantities and other documents including the Specifications, BOQ shall prevail.
f) The interpretation of the Consultant /Project in charge shall be final and binding.

The Contractor shall procure and bring Materials/Equipment to the site only on the basis of drawings approved for
4 construction and shop drawings and not on the basis of Bill of Quantities which are approximate only.

The contractor shall include for making all the opening in slabs, beams, walls etc. as required for his work. However,
the contractor can coordinate with civil work to provide necessary sleeves. All openings shall be closed using water
5 proofing compound, fire sealants or as specified by Project in charge.

The work shall be carried out in conformity with the plumbing drawings and within the requirements of Architectural,
6 HVAC, electrical, structural and other specialized services drawings.

The contractor shall cooperate with all trades and agencies working on the site. He shall make provision for hangers,
7 sleeves, structural openings and other requirements well in advance to prevent hold up of progress of the construction
schedule. All supports to the civil structure shall be provided with anchor fastners.

On award of the work the contractor shall be issued soft copies of consultant’s drawings which shall be the basis of
8 contractor’s shop drawings.

Shop drawings are detailed working drawings coordinated with other trading work, site conditions and incorporate
9 equipment manufacturer’s details and dimensions to ensure that the same can be installed in the space provided.

All shop drawings should detail pipe routing and levels, showing location of other services at crossings etc., cable runs,
10 route cable trays and all allied works and must be fully coordinated with other services, before execution of the works.

11 All shop drawings will be made on AutoCAD and color / black & white prints has to be produced for site work.

All rates quoted are inclusive of cutting holes and chases in walls and floors and making good the same with cement
mortar / concrete / water proofing of appropriate mix and strength as directed by the Project incharge. Contractor
shall provide holes, sleeves, recesses in the concrete and masonry work as the work proceeds. All hot and cold water
12 supply pipes crossing masonry walls of typical toilets shall be provided with MS pipe sleeves. The annular space
between the pipe and sleeve shall be filled up with glass wool in between and fire proof sealant on either end after
testing.

The contractor shall , from time to time, clear away all debris and excess materials accumulated at the site failing
13 which the same shall be done by Project incharge at contractor’s risk and cost and cost of clean up shall be deducted
from the contractors pro-rata bill.

After the fixtures, equipment and appliances have been installed and commissioned, contractor shall cleanup the same
and remove all plaster, paints, stains, stickers and other foreign matter or discoloration leaving the same in a ready to
14 use condition.

On completion of all works, contractor shall demolish all stores, remove all surplus materials and leave the site in a
broom clean condition, failing which the same shall be done by the Project incharge at the Contractor's risk and cost.
15 Cost of the cleanup shall be deducted from the contractor’s bills on pro-rata basis in proportion to his contact value.

ADITHI CONSULTANTS 2
 16 Rate to include for testing of all pipes, temporary platforms, erecting & removal of scaffolding.

17 All shaft cut out closing should be considered in civil scope

Base rate given is only for the given Model/fixture. Accessories, consumables,
18 unloading, fixing, installation, commissioning, wastage etc are part of
conversion cost. Also, base Rate is FOR Haringhata site

SL. NO. DESCRIPTION UNIT QUANTITY RATE (INR) AMOUNT (INR)

A SANITARY FIXTURES AND CP FITTINGS
Supplying, fixing, testing and commissioning, of wall mountedtype European
Water Closet with `P' trap with concealed flushing cistern with chrome flush
plate, dual flush (close coupled, 3 / 6 lts capacity as per IGBC requirement,
with all internal parts of the cistern for efficient functioning) with matching
Heavy duty closing seat cover of approved make, with Galvanised iron chair
1.0 Nos 112.00 12,919.01 1,446,929.36
bracket, fixing of 110mm dia straight type straight syphon UPVC WC pan
connector with neoprene rubber ring, necessary accessories including
cutting & making good the walls, floors, slab wherever required.(Model :
20098)-
Base Rate for EWC- Rs 7,000 (Model: 20098)
-
Supplying, fixing, testing and commissioning, white colour IWC of depth 350
mm (Orissa Pan) with 'P' or 'S' trap, with cistern (flow rate of 3 / 6 lts capacity
as per IGBC requirement all internal parts of the cistern, 450mm long CP
2.0 Nos 125.00 4,516.40 564,550.33
inlet connection pipe, 15mm CP angle valve, CP wall flanges,SS bolts and
nuts of approved make etc., complete.(Model : 20070)-
Base Rate for IWC- 2,500 (Model- 20070)
-
Supplying, fixing, testing and commissioning, of 15mm CP ablution tap
( health faucet) of approved make with necessary CP flexible hose 1.0 m long
3.0 Nos 112.00 1,366.48 153,045.76
nozzle pipe , CP wall flange Angle valve complete.(Model : F160001)
Base Rate for Health Faucet- Rs 800 (Model : F160001)
-
Supplying, fixing, testing and commissioning, of white colour glazed large flat
back urinals with auto closing concealed flush valve (pressmatic) , 40mm dia
CP waste coupling with dome type grating, 40mm dia CP bottle trap with
extension pipe, urinal spreader, 20mm dia C.P. , SS bolts and nuts to fix the
4.0 Nos 237.00 10,744.84 2,546,526.35
urinal with hangers and brackets complete with wall flanges.(Model : 96007
& PRS 073)
Base Rate for Urinal- Rs 7,000 (Model : 96007)

-
Supplying, fixing and commissioning of Compressed laminate urinal partition
with 12mm thick high pressure compressed laminate panel as per IS:2046
5.0 and EN438 all-round polished of size 450x900x12mm thick, using 2 nos SS Nos 191.00 2,940.91 561,714.45
clamps embedded in 150 x 150 PCC pocket etc. complete as directed by
Client/Project inchage.
-
Supplying, fixing, testing and commissioning of white glazed Circular /
rectangular wash basin under counter type, pillar cock auto closing system
(pressmatic), with waste coupling,32mm dia CP 'P' trap with extension,
1no.15mm CP angle valve 1no with 450mm long CP connection pipe 1nos and
6.0 Nos 245.00 7,982.48 1,955,707.36
CP wall flanges,etc.,complete. all of approved make etc.,with all required
consumables complete. ( Model : 10080/ 10065 & PSR-031)
Base Rate for Wash Basin- Rs 4,000 (Model : 10080/10065)

-
Supplying, fixing, testing and commissioning of single lever concealed
divertor unit with over head shower. CP elbow coupling pipe, spout and
overhead shower comprising of CP shower arm, pressure adjustable shower
7.0 Nos QRO 13,024.04
rose with CP wall flanges etc., with all required consumables complete.
(Make : DRC-37229, SPJ-35429pm, & OHS-1709)
Base rate of DRC-37229 Rs 2,000, SPJ- 35429- Rs 2,000)
-
Supplying, fixing, testing and commissioning of storage type water heater of
approved shade with copper container, glasswool insulation,stove enamelled
M.S jacket, thermostatically controlled inner heater with pilot neon lamps,
8.0 angle valve on inlet connection, 15mm dia C.P flexible connection pipe in inlet Nos QRO 17,330.38
& outlet suitable for working pressure of 3 kg/sqcm complete as required (25
lts).
Base Rate of 25 ltr- Water heater- Rs 12,000
-
Supplying, fixing, testing and commissioning of stainless steel towel ring with
9.0 nickel chrome finish, complete. (Model - F880007CP) Nos QRO 1,018.82
Base Rate of Towel Ring- F880007CP- Rs 600
-
Supplying, fixing, testing and commissioning of stainless steel tissue
10.0 dispenser with nickel chrome finish, complete (Model No- F880003CP) Nos QRO 1,522.97
Base Rate of Tissue Dispenser- F880003CP- Rs 1,000
-
Supplying, fixing, testing and commisioning of 15 mm dia C.P. brass tap
11.0 with C.P. wall flange of approved quality and making good as required Nos 194.00 892.78 173,198.79
including, IWC & Janitor room etc
-
Supplying, fixing, testing and commissioning of counter mounted type soap
12.0 dispencer with nickel chrome finish, complete (Model No- F840006CP) Nos QRO 1,522.97
Base Rate of soap Dispenser- F840006CP- Rs 1,000
Total A - Carried to Summary - 7,401,672.39
-
B INTERNAL SEWAGE SYSTEM - SOIL & WASTE -
ADITHI CONSULTANTS 3
 SL. NO. DESCRIPTION UNIT QUANTITY RATE (INR) AMOUNT (INR)
Supplying, fixing and testing PVC pressure pipes class 3, 6Kg/sqcm confirming
to IS4985 for waste water connection from AC indoor units, wash
basin,kitchen sinks to floor traps with solvent cement joints, including all the
necessary fittings such as elbow, tee, Y bend, shoes, and bushes etc
1.0 -
complete.,laid concealed in wall etc, the work shall include wall chase and
making good the same in cement mortar and restore the same original
condition neatly as directed by the Engineer in-charge etc.,complete with
necessary signages.
1.1 Internal toilets -
a) 40 mm dia RM 910.00 504.16 458,782.48
b) 50 mm dia RM 680.00 619.69 421,390.87
-
Providing, fixing, jointing and testing uPVC low noise silent SWR pipes and -
pushfit fittings (above 75 mm dia and less than 200mm dia) conforming to
EN 12056:2000, IS 13592:2013 (for pipes) and IS 14735:1999 (for fittings)
with sound insulation as per EN 14366), including all necessary GI fittings and
specials such as bends, tees, unions, reducers, flanges & plugs etc. Fixing at
2.0 wall / ceiling level, hangers etc. as per specification. In gradients and
alignments as approved complete, fixed to walls or ceiling or run on floor or
in trenches supported by clamps at required slopes as directed after testing
hydraulically and making good walls / surfaces, etc. Cost shall be inclusive of
clean out plugs. Rubber lined galvanised steel clamps and brackets. The
diameter of pipe shall be of the following nominal bores (NB):
2.1 Internal toilets -
a) 75 mm dia RM 365.00 278.34 101,592.80
b) 110 mm dia RM 4,300.00 661.71 2,845,333.64
-
2.2 Shaft Piping - Vertical Header -
a) 75 mm dia RM 310.00 252.08 78,144.27
b) 110 mm dia RM 525.00 567.18 297,767.47
-
Supplying, fixing and testing of Air Admittance Valves & fittings for vertical -
3.0 stack of pipe including cuting pipes to required length, and fixing in chases or
surface mounted with clamps
a) Air Admittance Valve (Maxi Vent) Nos. 16.00 12,183.78 194,940.54
-
-
Supplying, fixing and testing PVC deep seal self cleaning "P" trap with SS -
4.0 frame and cover 110 mm dia outlet with cockroach trap fixed on a bed of
cement concrete with (Heavy duty type) etc., complete.

a) 110mm dia Nos. 392.00 472.65 185,277.54

-
Supplying, fixing and testing clean out plugs, supports as with suitable GI U- -
5.0 clamps, bolts, nuts and washers etc., The clamps shall be painted with two
coats of enamel (approved) paint over a coat of primer etc., complete.

a) 110 mm dia Nos. 120.00 493.65 59,238.40

-
Total B - Carried to Summary - 4,642,468.01
-
C INTERNAL WATER SUPPLY SYSTEM - DOMESTIC, FLUSHING & HOT WATER -

-
Supplying, installing, fixing, jointing, testing and commissioning of approved -
make. Chlorinated Polyvinyl Chloride pipes (CPVC) SDR.11 pipes confirming to
ASTM standards with necessary fittings for internal toilet water supply upto
50 dia , and above 50mm dia pipe schedule 80 with fitting shall be schedule
80 ASTM IPS. The fittings and specials such as tees, elbows,couplers, bends,
enlargers etc.,m with CPVC brass threaded combination / transition specials
such as male adapters brass threaded female adapters, brass FPT Tee, Brass
FPT elbow etc., where connection with metal is to be made including
necessary drilling holes, chasing walls and making the same good in cement
mortar 1:1 restore the same original condition neately as directed by the
Engineer in-charge. Joints to be made with CPVC solvent cement up to 50mm
dia as per ASTM D-2846 and above 50mm dia primer P-70, and solvent
1.0 confirming to ASTM F-4931 / 724.The rate shall include necessary GI
supports, GI grip bolts, angle brackets, hangers, supports as with suitable GI
U-clamps, bolts, nuts and washers etc all as per E-I-C's requirement.The
clamps shall be painted with two coats of enamel (approved) paint over a
coat of primer etc., complete.
All nuts, bolts, washers, unions shall be hot dip galvanised.
(Domestic water supply system)

a) 20 mm dia RM 1,260.00 252.08 317,618.64

b) 25 mm dia RM 250.00 294.09 73,522.83
c) 32 mm dia RM 130.00 409.63 53,251.54
d) 40 mm dia RM 40.00 556.67 22,266.92
e) 50 mm dia RM QRO 913.78
-

ADITHI CONSULTANTS 4
 SL. NO. DESCRIPTION UNIT QUANTITY RATE (INR) AMOUNT (INR)
Supplying, installing, fixing, jointing, testing and commissioning of approved -
make. Unplasticized Polyvinyl Chloride pipes (uPVC) Sch 40 pipes confirming
to ASTM standards with necessary fittings for internal toilet water supply
upto 50 dia, and above 50mm dia pipe schedule 80 with fitting shall be
schedule 80 ASTM IPS. The fittings and specials such as tees, elbows,
couplers, bends, enlargers etc.,with PVC brass threaded combination /
transition specials such as male adapters brass threaded female adapters,
brass FPT Tee, Brass FPT elbow etc., where connection with metal is to be
made including necessary drilling holes, chasing walls and making the same
good in cement mortar 1:1 restore the same original condition neately as
directed by the Engineer in-charge. Joints to be made with PVC solvent
cement up to 50mm dia as per ASTM D-2846 and above 50mm dia primer P-
70, and solvent confirming to ASTM F-4931 / 724 . The rate shall include
3.0 necessary GI supports, GI grip bolts, angle brackets, hangers, supports as
with suitable GI U-clamps, bolts, nuts and washers etc., .The clamps shall be
painted with two coats of enamel (approved) paint over a coat of primer etc.,
complete.
All nuts, bolts, washers, unions shall be hot dip galvanised.
(Flushing water supply system)

a) 20 mm dia RM 775.00 126.04 97,680.34

b) 25 mm dia RM 220.00 173.30 38,126.84
c) 32 mm dia RM 140.00 262.58 36,761.42
b) 40 mm dia RM 70.00 304.59 21,321.62
b) 50 mm dia RM 15.00 409.63 6,144.41
-
Supplying & fixing Auto Air vent with in-built brass ball valve for water supply -
4.0 risers, suitable for pressure not less than 15 Kg/Sq.cm.
a) Air release valve size- 20mm Nos. 6.00 2,625.82 15,754.89
-
Providing, fixing, jointing and testing, PN10 forged brass ball valves F/F -
screwed end with SS lever operated of approved make, including flanges /
unions, nuts, bolts, washers, etc. complete, as approved by the Architect and
5.0
Engineer-in-charge for water supply lines of the following nominal bore (NB)
size:
All nuts, bolts, washers, unions shall be hot dip galvanised.
a) 20 mm dia Nos. 5.00 1,260.39 6,301.96
b) 25 mm dia Nos. 140.00 1,733.04 242,625.35
c) 32 mm dia Nos. 2.00 1,890.59 3,781.17
c) 40 mm dia Nos. 6.00 2,520.78 15,124.70
c) 50 mm dia Nos. QRO 3,623.63
-
Total C - Carried to Summary 950,282.62

ADITHI CONSULTANTS 5
 PROJECT : Warehousing at Haringhata, West Bengal
SUBJECT: BILL OF QUANTITIES FOR PHE SYSTEM - Civil Works
Notes to be read same as: BILL OF QUANTITIES FOR PHE SYSTEM - INTERNAL

SL. NO. DESCRIPTION UNIT QUANTITY RATE (INR) AMOUNT (INR)

ADITHI CONSULTANTS 6
 LIST OF RECOMMENDED MAKES

SL NO DESCRIPTION MAKE
1 SANITARY WARE HINDWARE or equivalent
2 CP FITTING JAQUAR /CERA/KOHLER
3 CPVC PIPES & FITTINGS ASHIRVAD / ASTRAL / SUPREME
4 NU DRAIN PIPES (RING) ASHIRVAD / ASTRAL / SUPREME
5 DWC PIPE ASHIRVAD / ASTRAL / SUPREME
6 GI PIPES - C CLASS JINDAL HISSAR/TATA
7 VALVES AND STRAINERS NVR / CRI / RB / ITAP
8 AIR RELEASE VALVES WATTS / CRI / HAWA / ITAP

9 PIPE PROTECTION TAPE (PVC) UNDERGROUND PYPCOAT / TWL / RUSTECH

10 PIPE PROTECTION TAPE (CONCEALED) TAPEX or equivalent

11 TOILET CUBICLE STELATEX or equivalent.
12 COMPRESSED LAMINATE MERINOX or equivalent.