Scribd Logo
Upload

Welcome to Scribd!

  • 141 views

    Adjust Pre Load Wheel Bearing 777 AGC

    Uploaded by

    Faidh Allanz Fairhia

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Adjust Pre Load Wheel Bearing 777 AGC

    Uploaded by

    Faidh Allanz Fairhia
    141 views4 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    141 views4 pages

    Adjust Pre Load Wheel Bearing 777 AGC

    Uploaded by

    Faidh Allanz Fairhia

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    777D Truck 3508B Engine AGC00001-UP (MACHINE)(SEBP3016 - 101) - Systems & ...

    Page 1 of 4

    Shutdown SIS

    Previous Screen

    Product: TRUCK
    Model: 777D TRUCK AGC
    Configuration: 777D Truck 3508B Engine AGC00001-UP (MACHINE)

    Testing and Adjusting


    776D, 777D and 777D HAA Off-Highway Truck Power Train
    Media Number -RENR3320-07 Publication Date -01/08/2007 Date Updated -09/08/2007

    i03199929

    Rear Wheel Bearing - Adjust


    SMCS - 4201-025-BD

    Illustration 1 g01631603

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/26/2012
    777D Truck 3508B Engine AGC00001-UP (MACHINE)(SEBP3016 - 101) - Systems & ... Page 2 of 4

    (1) Spindle

    (2) Shims

    (3) Retainer plate

    (4) Bolts

    Illustration 2 g01631604

    Typical example

    Location of the purge valve for the parking brakes

    Note: Before performing this adjustment, you will need to release the brakes. In order to release the
    parking brake, remove the purge valve from opening (A) . This opening is marked with a "P". Then,
    connect a manual hydraulic pump or an electric hydraulic pump to opening (A) . Continue to operate
    the pump until the brake is fully released. To learn more about releasing the brakes, refer to the
    information about towing that is located in the Air System and Brakes Systems Operation and Testing
    And Adjusting.

    NOTICE

    If it becomes necessary to use an outside hydraulic source to release the


    parking brake, do not exceed the relief pressure of the parking and
    secondary brake control valve. Exceeding the relief pressure can
    damage seals and other parts in the circuit.

    Adjustment Procedure
    1. Thoroughly, clean all of the tapped holes in the end of spindle (1) .

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/26/2012
    777D Truck 3508B Engine AGC00001-UP (MACHINE)(SEBP3016 - 101) - Systems & ... Page 3 of 4

    2. Install retainer plate (3) with six new bolts (4) to spindle (1) . Install bolts (4) so that each bolt
    is equally spaced around retainer plate (3) .

    Note: Do not use any shims (2) at this time.

    Illustration 3 g01631606

    View A-A

    (3) Retainer plate

    (4) Bolts

    3. Tighten bolts (4) to a torque of 140 N·m (103 lb ft). Turn the wheel for two complete
    revolutions.

    4. Tighten bolts (4) to 140 N·m (103 lb ft). Turn the wheel for two complete revolutions.

    5. Loosen bolts (4) by 120 degrees. Turn the wheel for two complete revolutions.

    6. Tighten bolts (4) to a torque of 110 N·m (81 lb ft). Turn the wheel for two complete
    revolutions.

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/26/2012
    777D Truck 3508B Engine AGC00001-UP (MACHINE)(SEBP3016 - 101) - Systems & ... Page 4 of 4

    7. Tighten bolts (4) to a torque of 110 N·m (81 lb ft). Turn the wheel for two complete
    revolutions.

    8. Use a depth micrometer to determine the distance from the outside face of retainer plate (3) to
    the end of spindle (1) . Measure the depth of the two holes that are opposite to each other on
    retainer plate (3) . Calculate an average depth from these two measurements.

    9. Use an outside micrometer to determine the thickness of retainer plate (3) at the bolt holes.
    Measure the thickness of retainer plate (3) at the same locations that were used in Step 8.
    Calculate an average thickness from these two measurements.

    10. Find the gap between the end of spindle (1) and the inside face of retainer plate (3) . To find
    this gap, subtract the dimension that was found in Step 9 from the dimension that was found in
    Step 8.

    11. Calculate the shim pack thickness. Add 0.381 mm (0.0150 inch) to the distance that was found
    in Step 10.

    12. Assemble shim pack (2) so that the shim pack thickness is the value that was found in Step 11.
    Remove bolts (4) and retainer plate (3) .

    13. Install shim pack (2) .

    14. Install retainer plate (3) over shim pack (2) . Install ten new bolts (4) .

    Note: Apply 9S-3263 Thread Lock Compound on the threads of ten new bolts (4) .

    15. Evenly torque opposite bolts (4) to 250 ± 15 N·m (185 ± 10 lb ft).

    16. Repeat Step 15 until no further movement of bolts (4) occurs.

    Copyright 1993 - 2012 Caterpillar Inc. Sat May 26 09:11:20 UTC+0800 2012
    All Rights Reserved.
    Private Network For SIS Licensees.

    https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 5/26/2012

    You might also like