Scribd Logo
Upload

Welcome to Scribd!

  • 55 views

    The Design Is Adequate.: W F F X X X y X

    Uploaded by

    xuankhoi doanvan
    This document summarizes the seismic design of intermediate/ordinary moment resisting frames based on various codes. It provides the input data for a sample column and beam section. It then analyzes the design to check if it satisfies various code requirements for local buckling limits, continuity plate thickness, panel zone thickness, and weld sizes. The design is found to be adequate with the addition of a doubler plate in the column thickness of 1-5/8 inches.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd

    The Design Is Adequate.: W F F X X X y X

    Uploaded by

    xuankhoi doanvan
    55 views3 pages
    This document summarizes the seismic design of intermediate/ordinary moment resisting frames based on various codes. It provides the input data for a sample column and beam section. It then analyzes the design to check if it satisfies various code requirements for local buckling limits, continuity plate thickness, panel zone thickness, and weld sizes. The design is found to be adequate with the addition of a doubler plate in the column thickness of 1-5/8 inches.

    Original Title

    omrf-cbc

    Copyright

    © © All Rights Reserved

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document summarizes the seismic design of intermediate/ordinary moment resisting frames based on various codes. It provides the input data for a sample column and beam section. It then analyzes the design to check if it satisfies various code requirements for local buckling limits, continuity plate thickness, panel zone thickness, and weld sizes. The design is found to be adequate with the addition of a doubler plate in the column thickness of 1-5/8 inches.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    55 views3 pages

    The Design Is Adequate.: W F F X X X y X

    Uploaded by

    xuankhoi doanvan
    This document summarizes the seismic design of intermediate/ordinary moment resisting frames based on various codes. It provides the input data for a sample column and beam section. It then analyzes the design to check if it satisfies various code requirements for local buckling limits, continuity plate thickness, panel zone thickness, and weld sizes. The design is found to be adequate with the addition of a doubler plate in the column thickness of 1-5/8 inches.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 3

    PROJECT : PAGE :

    CLIENT : DESIGN BY :
    JOB NO. : DATE : REVIEW BY :
    Seismic Design for Intermediate/Ordinary Moment Resisting Frames Based on CBC 07, AISC 341-05 & AISC 358-05

    INPUT DATA & DESIGN SUMMARY


    COLUMN SECTION => W8X48
    A d tw bf tf Sx Ix rx ry Zx k
    14.1 8.5 0.40 8.11 0.69 43.2 184 3.61 2.08 49 1.08
    BEAM SECTION => W14X48
    A d tw bf tf Sx Ix rx ry Zx k
    14.1 13.8 0.34 8.03 0.60 70.2 484 5.86 1.91 78 1.19

    STRUCTURAL STEEL YIELD STRESS Fy = 50 ksi


    THE FACTOR AXIAL LOAD ON THE COLUMN Pu = 27 kips
    BEAM LENGTH BETWEEN COL. CENTERS L= 33 ft
    AVERAGE STORY HEIGHT OF ABOVE & BELOW h= 9 ft
    CBC 07 Chapter A (DSA only) APPLY? == > Yes

    THE DESIGN IS ADEQUATE.


    (Continuity column stiffeners 0.75 x 4
    with 1/4" fillet weld to web & CP to flanges.
    A doubler plate is required with thickness of 1-5/8 in. )

    ANALYSIS
    THE SEISMIC DESIGN FACTOR COMPARISON (ASCE 7-05, Table 12.2-1)
    FRAME TYPE R Wo Cd
    SMRF 8 3 5 1/2
    IMRF 4.5 3 4
    OMRF 3.5 3 3

    CHECK BEAM LOCAL BUCKLING LIMITATION (AISC 341-05 Tab. I-8-1)


    bf / (2tf ) = 6.75 < 0.3 (Es / Fy)0.5 = 7.22 [Satisfactory]
    [ 52 / (Fy)0.5 for AISC Seismic 97, Tab. I-9-1]

    Where Es = 29000 ksi


    h / tw = 33.59 < 2.45 (Es / Fy)0.5 = 59.00 [Satisfactory]
    [ 418 / (Fy)0.5 for FEMA Sec. 3.3.1.2]
    CHECK COLUMN LOCAL BUCKING LIMITATION (AISC 341-05 Tab. I-8-1)
    bf / (2tf ) = 5.92 < 0.3 (Es / Fy)0.5 = 7.22 [Satisfactory]
    [ 52 / (Fy)0.5 for AISC Seismic 97, Tab. I-9-1]
    3.14(Es/Fy)0.5(1-1.54Pu/fbPy) = 70.67 , for Pu/fbPy < 0.125
    h / tw = 15.85 < [ 520 / (Fy)0.5(1-1.54Pu/fbPy) for AISC Seismic 97, Tab. I-9-1]
    (Es/Fy)0.5 MAX[1.49, 1.12(2.33 - Ca)] = N/A , for Pu/fbPy > 0.125
    { MAX[ 191 / (Fy)0.5(2.33-Pu/fbPy) , 253 / (Fy)0.5] for AISC Seismic 97, Tab. I-9-1}

    [Satisfactory] Where fb = 0.9 , Py = FyA = 705 kips

    CHECK CONTINUITY PLATE REQUIREMENT (AISC 358-05 Sec. 2.4.4)


    tcf = MIN{ bbf / 6 , 0.4[1.8bbf tbf (FybRyb) / (FybRyb)] 0.5 }= 1.17 in > actual tcf
    (The continuity plates required.)
    tst = tbf for interior connection, or (tbf /2) for exterior connection = 0.60 in,USE 0.75 in, ( 5/8 in )
    bst = 4 in < 1.79 (Es / Fyst )0.5 tst = 38.10 in, (LRFD Sec. K1.9)
    [Satisfactory]
    fcPn,st = fcFcr A = 288.0 kips
    Where fc = 0.9 hst = dc - 2k = 6.34
    K = 0.75 K hst / rst < 200 (AISC 360, E2) [Satisfactory]
    I = tst (2bst + twc) 3 / 12 = 36 in 4 lc = 0.026
    A = 2bsttst + 25(twc) 2 = 9 in2 Fcr = 35.99 ksi
    rst = ( I / A )0.5 = 2.02 in Fyst = 36 kips, plate yield stress
    Pu,st = Ryb Fyb bfb tfb = 262.8 kips < fcPn,st [Satisfactory]

    The best fillet weld size (AISC 360-05 Sec.J2.2b)


    > wMIN = 0.1875 in
    w= 1/4 in
    < wMAX = 0.3125 in
    [Satisfactory]
    The required weld length between A36 continuity plates and column web (AISC 360-05 Sec.J2.2b)
    Lw = 0.6tstLnstFy / [(2) f Fw (0.707 w)] = (0.75 x 3.3) x 36 / [(2) 0.75 (0.6x70)(0.707x1/4)] = 3.44 in
    Where Lnet = dc - 2(k + 1.5) = 3.3 < 2(Lnet -0.5) [Satisfactory]
    (Use complete joint penetration groove welds between continuity plates & column flanges.)
    (cont'd)

    CHECK PANEL ZONE THICKNESS REQUIREMENT (AISC 341-05 Sec. 10.2d)


    tReqD = MAX (t1, t2) = 2.02 in
    t1 = Cy Mpr (h - db ) / [0.9 (0.6) Fyc Ryc dc (db - tfb) h] = 2.02 in
    Where Cy = Sb / (Cpr Zb) = 0.78
    Cpr = 1.15 (AISC 341-05 Sec. 9.6 & AISC 358-05 Sec. 2.4.3)
    Ry = 1.1 (AISC 341-05 Tab. I-6-1)
    Sb = 2Ib / db = 70 in2
    Ib = Ix = 484 in 4

    Mpr = Nb CprRyFyb Zb = 826 ft-kips


    Nb = 2 , (if double side connection of beams, input 2)
    t2 = (dz + wz ) / 90 = (db -2tst + dc - 2k) / 90 = 0.21 in

    Since twc = 0.40 in < tReqD , a doubler plate is


    required with thickness of 1-5/8 in.

    Technical References:
    1. AISC 341-05: "Seismic Provisions for Structural Steel Buildings", American Institute of Steel Construction, Nov. 16, 2005.
    2. AISC 360-05: "Specification for Structural Steel Buildings", American Institute of Steel Construction, March 9, 2005.
    3. AISC 358-05: "Prequalified Connections for Special and Intermediate Steel Moment Frames for Seismic Applications",
    American Institute of Steel Construction, Dec 13, 2005.
    4. Thomas A. Sabol, Ph.D., S. E.: "2005 AISC Seismic Provisions and Seismic Design Manual Seminar", AISC, Oct. 12, 2006.

    You might also like