Kathrein 2017 Same-Band Combiner and Hybrid Combiner Types

Summary of Same-Band Combiner and
Hybrid Combiner Types
Description Type No. Frequency range Max. input power Connector Page
Hybrid Combiner 2:1 78210500 791 – 960 MHz 60 W at each port 7-16 415
Hybrid Combiner 8:4 78211141 698 – 960 MHz 75 W 7-16 419, 420
1710 – 2690 MHz at each port
1920 – 2170 MHz
1920 – 2170 MHz
2500 – 2690 MHz
Hybrid Combiner 3:3 78211216 548 – 2690 MHz 150 W at each port 4.3-10 421
Same-Band Combiner 78211237 791 – 862 MHz 100 W at each port 7-16 423
Duplex Hybrid Combiner 78210805 Rx: 880 – 915 MHz 250 W 7-16 424, 425
Tx: 925 – 960 MHz
Active Duplex Hybrid 78211110 Rx: 880 – 915 MHz 250 W 7-16 426, 427
Combiner Tx: 925 – 960 MHz
Same-Band Combiner 78210936 880 – 960 MHz 100 W at each port 7-16 428, 429
Same-Band Combiner 78211228V01 2500 – 2640 MHz 100 W at each port 4.3-10 440, 441
Same-Band Combiner 78211228V03 2500 – 2960 MHz 100 W at each port 4.3-10 442, 443
3-dB Coupler 78210524 698 – 2690 MHz 150 W at each port 7-16 444, 445
3-dB Coupler 78210525 698 – 2690 MHz 1000 W at each port 7-16 446, 447
3-dB Coupler 793554 800 – 2200 MHz 300 W 7-16 448
New
Products
412
Summary of Same-Band Combiner and
Hybrid Combiner Types
Frequency Combinations
Same-Band and Hybrid Combiners
413
414
Hybrid Combiner 2:1
791 − 960 MHz
2 x 60 W
• Designed for the decoupled combining of 2 transmitter
or receiver signals onto one common antenna
Port 3
• The frequency spacing between transmitter signals can
be as small as required
• Excellent intermodulation performance
• Suitable for indoor or outdoor applications
Port 1
• Wall or mast mounting
• DC by-pass between all ports Port 2
• External DC stop available as an accessory
Technical Data
Type No. 78210500

Frequency range 791 - 960 MHz
Attenuation

Port 1 ↔ Port 3 3.1 ±0.5 dB
Port 2 ↔ Port 3 3.1 ±0.5 dB
Port 1 ↔ Port 2 > 23 dB*
VSWR < 1.15
Impedance 50 Ω
Input power
Port 1 60 W
Port 2 60 W
Intermodulation products < -160 dBc (3rd order; with 2 x 20 W)
Temperature range -40 ... +55 °C
Connectors 7-16 female (long neck)
Application Indoor or outdoor (IP 66)
DC/AISG transparency By-pass between all ports (max. 2500 mA)
AISG attenuation: 3 dB with external DC stop (see con-
figuration examples) / 6 dB without external DC stop
Mounting Wall mounting: With 4 screws (max. 6.5 mm diameter)
Mast mounting: With additional clamp set
Weight 3.7 kg
Packing size 377 x 232 x 189 mm
Dimensions (w x h x d) 143.6 x 199 x 97.5 mm (without connectors)
* Valid if all ports are terminated with 50-Ohm loads.
Note:
The input power rating of 60 W per port is specified at an ambient temperature of
+55 °C with the combiner mounted vertically, without additional cooling, and while
respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C).
If mounted vertically and/or used at a lower ambient temperature, then a higher input
power in accordance with the following table is possible:
Max. input power per port

Mounted horizontally Mounted vertically
Max. ambient
temperature
+55 °C 60 W 70 W
+40 °C 70 W 80 W
+25 °C 75 W 85 W
415
Hybrid Combiner 2:1
1710 − 2170 MHz
2 x 60 W

Port 3
• Wall or mast mounting Port 1
• DC bypass between all ports
• External DC stop available as an accessory Port 2
Technical Data
Type No. 78210502
Frequency range 1710 – 2170 MHz
Attenuation
Port 1 Port 3 3.1 ±0.5 dB
Port 1 Port 2 > 22 dB *
VSWR (all ports) < 1.25
Impedance 50 Ω
Input power
Port 1 < 60 W
Port 2 < 60 W
Intermodulation products < –160 dBc (3 rd order; with 2 x 20 W)
Temperature range –40 … +55 °C
DC/AISG transparency Bypass between all ports (max. 2500 mA)
AISG: Attenuation 3 dB with / 6 dB without
external DC stop at either Port 1 or Port 2
Mounting Wall mounting: With 4 screws (max. 6.5 mm diameter)
Weight 3.7 kg
Dimensions (w x h x d) 143.6 x 256 x 97.5 mm (including connectors)
* Valid if all ports are terminated with 50-Ω loads.
Note:
The input power rating of 60 W per port is specified at an ambient temperatu-
re of +55 °C with the combiner mounted horizontally, without additional cooling,
and while respecting the safety standard EN IEC 60950 (max. surface tempe-
rature +90 °C).
If mounted vertically and/or used at a lower ambient temperature, then a higher
input power in accordance with the following table is possible:
Max. ambient
temperature
+55 °C 60 W 70 W
+40 °C 70 W 80 W
+25 °C 75 W 85 W
416
Hybrid Combiner 2:1
698 − 2690 MHz
2 x 60 W

Port 1
• Excellent intermodulation performance Port 3

• Wall or mast mounting
• DC bypass between port 1 and port 3
Port 2
Technical Data
Type No. 78210504

Frequency range 698 – 2690 MHz
Attenuation
Port 1 Port 2 > 23 dB *
VSWR (all ports) < 1.2 (698 – 2170 MHz) / < 1.25 (2170 – 2690 MHz)
Impedance 50 Ω
Input power
Port 1 < 60 W
Port 2 < 60 W
Intermodulation products < –160 dBc (3 rd order; with 2 x 20 W)
Temperature range –40 … +55 °C
DC/AISG transparency
Port 1 Port 3 Bypass (max. 2500 mA)
Port 2 Port 3 Stop
Mounting Wall mounting: With 4 screws (max. 8 mm diameter)
Weight 4.3 kg
Dimensions (w x h x d) 264 x 203 x 72.5 mm
(without connectors, without mounting brackets)

- Clamp set (type no. 734360 - 734365),
- DC stop (type no. 78210850V01)
Note:
The input power rating of 60 W per port is specified at an ambient temperature
(order separately) can be found in the
of +55 °C with the combiner mounted vertically, without additional cooling, and section “System Components”.
while respecting the safety standard EN IEC 60950 (max. surface temperature
+90 °C).
If used at a lower ambient temperature, then a higher input power in accor-
dance with the following table is possible:
Max. ambient
temperature
+55 °C 55 W 60 W
+40 °C 70 W 75 W
+25 °C 80 W 85 W
417
Hybrid Combiner 2 : 1
698 – 2690 MHz
2 x 150 W

• DC by-pass between port 2 and port 3
Port 2
Port 3
Port 1
Technical Data
Type No. 78210506

Frequency range [MHz] 698 – 2690
Attenuation
Port 1 ↔ Port 3 [dB] 3 ±0.6
Port 2 ↔ Port 3 [dB] 3 ±0.6
Port 1 ↔ Port 2 [dB] > 25*
VSWR (all ports) < 1.12 (698 – 2690 MHz)
Impedance [Ω] 50
Input power
Port 1 [W] < 150
Port 2 [W] < 150
Intermodulation products [dBc] < −160 (3rd order; with 2 x 20 W)
Temperature range [°C] −40 ... +55
Connectors 7-16 female
Port 1 ↔ Port 3 Stop
Port 2 ↔ Port 3 By-pass (max. 2500 mA)
Mounting [mm | in] Wall mounting: With 4 screws (diameter max. 8 | 0.31) /
Weight [kg | lbs] 8 | 17.64
Packing size [mm | in] 545 x 280 x 190 | 21.46 x 11.02 x 7.48
Dimensions (w x h x d) [mm | in] 235 x 480 x 120 | 9.25 x 18.90 x 4.72
Note:
The input power rating of 150 W is specified at an ambient tempera-
ture of +40 °C with the combiner mounted vertically, without additional
cooling, and while respecting the safety standard EN IEC 60950 (max.
surface temperature +90 °C).
The max. power rating increases or decreases with falling or rising Max. ambient
ambient temperature and depending on horizontal or vertical mounting temperature
in accordance with the following table:
+55 °C 80 W 100 W
+40 °C 110 W 150 W
- Clamp set (type no. 734360 - 734365),
- DC stop (type no. 78210850V01) +25 °C 150 W 100 W
(order separately) can be found in the section “System
Components”.
418
Hybrid Combiner System
8 : 4 / 8 : 4 / 12 : 4 / 16 : 4
• Point of Interface (POI) for coverage solutions

with passive Distributed Antenna Systems (DAS)
• Designed for the decoupled combining of 8/12/16
transmitter or receiver signals and distributing these
signals evenly onto 4 antenna outputs.
• External 50 Ohm loads available as an
accessory
78211141 78211142

78211143 78211144
Technical Data
Type No. 78211141 78211142 78211143 78211144

8:4 8:4 12 : 4 16 : 4
Frequency range
Band 1 698 - 960 MHz 1710 - 1880 MHz 698 - 960 MHz 698 – 960 MHz
Band 2 1710 - 2690 MHz 1920 - 2170 MHz 1710 - 1880 MHz 1710 – 1880 MHz
Band 3 1920 - 2170 MHz 1920 – 2170 MHz
Band 4 2500 – 2690 MHz
Power distribution loss
(excluding insertion loss)
Input 1...8/12/16 ↔ Output 1...4 6 ± 0.8 dB
Typically 6.5 dB
Insertion loss
Input 1...8/12/16 ↔ Output 1...4 < 0.7 dB
Isolation between input ports
Same bands > 22 dB *)
Different bands > 50 dB
VSWR (all ports) < 1.5
Impedance 50 Ω
Input power at each input port < 75 W < 75 W < 50 W < 50 W
Intermodulation products < -155 dBc (3 order; with 2 x 20 W)
rd

Application Indoor or Outdoor (IP 66)
Mounting Wall mounting: With 4 screws (max. 6 mm diameter) / 19“-drawer
Weight 12 kg 15 kg 18.5 kg 21.5 kg
Packing size (w x h x d) 570 x 272 x 584 mm
Dimensions (w x h x d) 19” drawer x 19” drawer x 19” drawer x 19” drawer x
189.5 x 374 mm 183 x 374 mm 190 x 374 mm 187.25 x 374 mm
* Valid if all ports are terminated with 50-Ohm loads
Note:
The use of fewer than 8/12/16 inputs or 4 outputs is possible. Any unused input ports have to be terminated with low-
power 50-Ohm loads (e.g. Kathrein type 78410367), unused output ports have to be terminated with high-power
50-Ohm loads (e.g. Kathrein low intermodulation type 78210474).
419
Hybrid Combiner
8 : 4 / 8 : 4 / 12 : 4 / 16 : 4
78211141, -2, -3, -4
78211141
78211142
78211143
78211144
2170 2170 2170 2170
420
548 – 2690 MHz
Preliminary Issue

or receiver signals and distributing these signals equally
onto 3 antenna outputs
• Suitable for indoor and outdoor applications
• DC/AISG by-pass
Technical Data
Type No. 78211216

Frequency range [MHz] 548 – 2690
Insertion loss
Input 1 … 3 ↔ Output 1 … 3[dB] 4.9 ± -1.9/+2.3 (548 – 698 MHz)
4.9 ± 1.3 (698 – 800 MHz)
4.9 ± 0.9 (800 - 2500 MHz)

4.9 ± 1 (2500 - 2690 MHz)
Isolation
Input 1 … 3 ↔ Input 1 … 3[dB] > 25
Output 1 … 3 ↔ Output 1 … 3[dB] > 25
Directivity[dB] > 25
Return loss[dB] > 21
Impedance[Ω] 50
Input power [W] < 150 at each input port
Intermodulation products [dBc] < –160 (3rd order; with 2 x 20 W)
Temperature range [°C] –40 ... +70
Connectors 4.3-10 female
Application Indoor or outdoor (IP67)
DC/AISG transparency Bypass (max. 2500 mA) between
Input 1 <-> Output 3
External DC stop available as an accessory
Weight [kg] approx. 1
Dimensions (w x h x d) [mm] 176 x 57 x 31 (without connectors)
Note:
VSWR and attenuation values only valid if all ports are terminated with 50-Ohm-loads.
Note:
The use of fewer than 3 inputs or outputs is possible.
Any unused input ports have to be terminated with lowpower
50-Ohm loads, unsused output ports have to be terminated
with highpower 50-Ohm loads.
421
Hybrid Combiner 4:4
698 – 2690 MHz
4 x 150 W
• Designed for the decoupled combining of 4 transmitter Output 1
or receiver signals and distributing these signals equally
Output 2
onto 4 antenna outputs
• Suitable for indoor or outdoor applications Output 3
• DC/AISG bypass Output 4

Input 1
Input 2
Technical Data Input 3
Type No. 78210534 Input 4

Insertion loss
Input 1...4 ↔ Output 1...4 0.35 ± 0.15 dB
Power distribution loss Typically 6.3 dB
(excluding insertion loss)
Input 1...4 ↔ Output 1...4 6 ± 0.75 dB
Isolation
Input 1...4 ↔ Input 1...4 > 20 dB*
Output 1...4 ↔ Output 1...4 > 20 dB*
VSWR (all ports) < 1.22 (698 - 2170 MHz)
< 1.4, typ. 1.2 (2170 - 2690 MHz)
Impedance 50 Ω
Input power < 150 W at each input port
Application Indoor or Outdoor (IP 66)
DC/AISG transparency Bypass (max. 2500 mA) between
Input 1 ↔ Output 4 / Input 2 ↔ Output 2 /
Input 3 ↔ Output 3 / Input 4 ↔ Output 1
Mounting Wall mounting: With 4 screws (max. 8 mm
diameter)
Mast mounting: With mounting kit
Weight 4.5 kg
Dimensions (w x h x d) 375.9 x 65 x 224.2 mm
(with connectors and mounting feet)
* Valid if all ports are terminated with 50-Ohm loads
Note:
The use of fewer than 4 inputs or outputs is possible. Any unused
input ports have to be terminated with low-power 50-Ohm loads
(e.g. Kathrein type 784 10367), unused output ports have to be
terminated with high-power 50-Ohm loads (e.g. Kathrein low-
intermodulation type 78210474).
Accessories (order separately)

DC stop 50-Ohm load 50-Ohm load
Type No. Description
78210850V01 DC stop
78210474 50-Ohm load (80 W)
78410367 50-Ohm load (1.5 W)
422
Same-Band Combiner
791 – 801 / 832 – 842 MHz 811 – 821 / 852 – 862 MHz
• Enables antenna and feeder sharing for two base

stations in the same frequency band
Port 2 Port 3
• Suitable for two operators with frequency allocations
within the same frequency band
Port 4
• Very low Tx/Rx insertion loss compared to standard
Port 6
hybrid combiners
• Double unit for XPol antennas Port 1
Port 5
• DC/AISG by-pass for DTMA supply
Block Diagram

Technical Data
Type No. 78211237

Pass band
BTS 1 (LTE800 / Operator 1) Tx1/Tx2 = 791 – 801 MHz, Rx1/Rx2 = 832 – 842 MHz
BTS 2 (LTE800 / Operator 2) Tx3/Tx4 = 811 – 821 MHz, Rx3/Rx4 = 852 – 862 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 < 0.5 dB (791 – 801 MHz) / < 0.7 dB (832 – 842 MHz)
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (791 – 801 / 811 – 821 / 832 – 842 / 852 – 862 MHz)
VSWR < 1.2 (pass bands)
Impedance 50 Ω
Input power Tx1 / Tx2 / Tx3 / Tx4 < 100 W / < 100 W / < 100 W / < 100 W
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Stop
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 By-pass (max. 2500 mA)
Lightning protection 3 kA, 10/350 µs pulse
Mounting Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set
Weight 6.9 kg
Dimensions (w x h x d) 275 x 176 x 140 mm (without connectors, without mounting brackets)
- Clamp set (type no. 734360 - 734365) and

- 50-Ohm load (type no. 78410367)
(order separately) can be found in the section “System Components”.
423
Duplex Hybrid Combiner (Same-Band Combiner)
880 − 960 MHz 880 − 960 MHz
• Enables antenna and feeder sharing for two base stations

in the 900 MHz frequency band
• Very low insertion loss over full EGSM/UMTS 900 Tx band Port 3
width compared to standard hybrid combiners Port 6
• Double unit in one housing for XPol antennas Port 2
• Suitable for indoor or outdoor applications Port 1
• DC/AISG bypass for DTMA supply (for UMTS paths only) Port 4
• Rx diversity ports protected against incorrectly connected
Tx power Port 5
Technical Data
Type No. 78210805
Pass band
Rx MHz 880 – 915
Tx MHz 925 – 960
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 dB < 0.4, typically 0.2 (925 – 960 MHz) –
see Diagram I and II
dB < 4.3, typically 3.6 (880 – 915 MHz) –
see Diagram I and II
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 dB < 4.0, typically 3.5 (880 – 915 MHz) –
see Diagram III and IV
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 dB > 25 (880 - 915 MHz)
dB > 35 (925 - 960 MHz)
VSWR < 1.2 (880 - 915 / 925 - 960 MHz)
Impedance Ω 50
Input power W Port 1: < 250 Port 2: < 50
W Port 4: < 250 Port 5: < 50
Intermodulation products dBc < –160 (3rd order; with 2 x 20 W)
Temperature range °C –40 ... +65
Mounting With 4 screws (max. 8 mm diameter)
Weight kg | lb 6.5 | 14.3
Packing size mm | in 390 x 470 x 160 | 15.4 x 18.5 x 6.3
Dimensions (w x h x d) mm | in 287.1 x 278.6 x 71 | 11.3 x 7.0 x 2.8
424
Duplex Hybrid Combiner (Same-Band Combiner)
880 − 960 MHz 880 − 960 MHz
Accessories (order separately) Clamp Set

Type No. Clamp set suitable for Typical Attenuation Curves
Diagram I
mast diameter of mm | in
Port 1 Port 3
734360 34 – 60 | 1.34 – 2.36 Port 4 Port 6
734361 60 – 80 | 2.36 – 3.15 0
Attenuation/dB
734362 80 – 100 | 3.15 – 3.94 5
734363 100 – 120 | 3.94 – 4.72 10

880 - 915 925 - 960
DC stop
734364 120 – 140 | 4.72 – 5.51 15
734365 45 – 125 | 1.77 – 4.92 20
25
30
Type No. Description 35
78210850V01 DC stop 50-Ohm load

40
45
78410367 50-Ohm load
1.5 W / indoor or outdoor 50
870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz

Diagram II Port 1 Port 3
Port 4 Port 6
0
Attenuation/dB
0.5
1.0
880 - 915 925 - 960
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz
Diagram III Port 2 Port 3

Port 5 Port 6
0
Attenuation/dB
10
880 - 915 925 - 960
15
20
25
30
35
40
45
50
870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz
Diagram IV Port 2 Port 3

Port 5 Port 6
0
Attenuation/dB
0.5
1.0
880 - 915 925 - 960
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Application example
870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz
425
Active Duplex Hybrid Combiner (tunable)
Active Duplex Hybrid
(Same-Band Combiner (Same-Band Combiner)
Combiner)
880– ...
880 915960
/ 925MHz
– 960 MHz 880
880...– 960
915 / MHz
925 – 960 MHz
EGSM 900 UMTS 900
• Enables
in the 900antenna and feederband
MHz frequency
the 900 MHz frequency band
sharing for two base stations in RET = Remote Electrical Tilt
AISG = Antenna Interface Standards Group
•• 12Very
• 12 dB gain over 20 MHz Rx bandwidth (factory tunable) CWA = Current Window Alarm
dB gain over 20 MHz Rx bandwidth (factory tunable)
• tunable)
Very
low insertion loss over 20 MHz Tx bandwidth (factory
low insertion
tunable) compared
compared
loss over 20 MHz
totostandard
standard Tx combiners
hybrid
hybrid
bandwidth (factory
combiners
•• Double
Doubleunit unitininone
onehousing
housingfor
forXPol
XPolantennas
antennas
•• Suitable
Suitablefor forindoor
indoorororoutdoor
outdoorapplications
applications
Port 3
•• Supports
SupportsAISG AISG1.1 1.1and
andAISG
AISG2.0
2.0(default)
(default)
Port 6
• standard
Suitableforforantenna
• Suitable
standard
antennaRET RETcontrol
controlaccording
according to to AISG/3GPP
AISG/3GPP
•• Bypass
Bypassmode
power
powerdown
mode
down
(LNA)
(LNA) to to ensure
ensure cellcell operation
operation in case
in case of DC
of DC
•• Built-in
Built-inlightning
lightning protection
protection
Frequency
Frequency ordering information:
ordering information:
When
Whenordering please
ordering specify
please the required
specify Tx-and Rx-frequencies
the required Tx- and
Port 1
Examples of tuning versions:
Rx-frequencies
78211110V01:
Examples ofRx 880 – versions:
tuning 900 MHz, Tx 925 – 945 MHz RET
78211110V02:
78211110V01Rx 895880
: Rx – 915 MHz,MHz,
– 900 Tx 940Tx– 925
960 MHz
– 945 MHz Port 2
Other frequencies on request.
78211110V02: Rx 895 – 915 MHz, Tx 940 – 960 MHz Port 4 Port 5
Other frequencies on request.
Technical Data
Type No. 78211110
Technical
Pass band Data
Rx 20 MHz within 880 ... 915 MHz (factory tunable)
Type
Tx No. 78211110
20 MHz within 925 ... 960 MHz (factory tunable)
Tx
PassInsertion
band loss
Port
Rx2 � Port 3 / Port 5 � Port 6 < 0.2MHz
dB (925 – 94520MHz)* within–880see...Diagram I andtunable)
915 (factory II
Tx
Isolation MHz 20 within 925 ... 960 (factory tunable)
TxPort 1 � Portloss
Insertion 2 / Port 4 � Port 5 > 25 dB (880 – 900 MHz)*
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 dB > 65 dB (925
< 0.2 (925 –– 945
945 MHz)
MHz)** – see Diagram I and II
Gain
Isolation 12 dB nominal
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 dB > 25 (880 – 900 MHz)
Gain ripple dB ±1 dB > 65 (925 – 945 MHz)
Loss
Gain in bypass mode dB < 5.5 dB (DC OFF) 12 nominal
Return loss
Gain ripple > 18 dB (DC ON) / > 12 dB (DC
dB ±1OFF)
Noise
Loss infigure
bypass mode dB < 1.6 dB (+22 ... +28 < 5.5°C) (DC OFF)
Return1-dB
Output losscompression point dB > 18
> 11 dBm (DC ON) / > 12 (DC OFF)
3Return
rd orderloss
intercept point (OIP3) dB
> 25 dBm (typically 30 < 1.6
dBm) (+22 ... +28 °C)
Output 1-dB compression point
VSWR dBm
< 1.25 (880 – 900 / 925 – 945> 11
MHz)*
3rd order intercept point (OIP3) dBm > 25 (typically 30 dBm)
Impedance 50 Ω
VSWR < 1.25 (880 – 900 / 925 – 945 MHz) *
Input power Port 2 < 200 W
Impedance Ω Port 5 < 200 W 50
Input power
Intermodulation products W< 160 dBc (5th order, with Port2 x220< 200
W)
Port 5 < 200
Environmental Characteristics
Intermodulation products dBc < –160 (5 order; with 2 x 20 W)
th
Operating
Environmental temperature range
Characteristics –40 … +65 °C
IP rating temperature range
Operating °C IP67 (see note on page –40 2)... +65
IP rating
MTBF > 1 000 000 hours IP 67(per
(seeTMA)note on page 2)
MTBF
EMC According to>ETS 1 000300 000 hours (per TMA)
342-3
EMC According to ETS 300 342-3
DC and Alarm Characteristics CWA Mode AISG Mode
DC supply 9 – 19 V 9 – 30 V
DC supply V 9 – 19 9 – 30
Operating
Operating current
current per
per TMA
TMA 80
mA– 120 mA 80 – 120 Nom. 20 mA Nom. at 9 V80 at 9 V
(without
(without RET)RET) Nom. 30 mA Nom. at 30 V30 at 30 V
Alarm management
Alarm management 170
mA– 200 mA170 – 200 AISG (see AISG note on page
(see 2) on page 2)
note
Mechanical
MechanicalCharacteristics
Characteristics
Connectors
Connectors RF RF 7-16 female (long neck) (long neck)
7-16 female
AISG AISG 8-pin female,8-pin IEC 60130-9
female, IEC 60130-9
(Pin 3: RS485B,(Pinpin 5: RS485A,
3: RS485B, pinpin5: 6: 9 – 30 V
RS485A, DC,
pin 6: 9 – 30 V DC,
pin 7: DC return,
pin 7:other pins: not
DC return, connected)
other pins: not connected)
Mounting
Mounting Wall mounting: Wall
with mounting:
4 screws (max.with 48screws (max. 8 diameter)
mm diameter)
Mast mounting: Mast mounting:
with additional with additional
clamp set clamp set
Weight kg | lb 6.8 | 15.0
Weight 6.8 kg
Packing size 460 x 375 x 135 | 18.1 x 14.8 x 5.3
Packing
Dimensions size(w x h x d) mm | in 460 x 375369xx135 209mm x 68 | 14.5 x 8.2 x 2.7
Dimensions (w x h x d) 369 x 209
(without x 68 mm without mounting brackets)
connectors,
* Tuning version 78211110V01: Rx (without
880 – 900 connectors,
MHz, Tx 925 without
– 945mounting
MHz brackets)
* Tuning version 78211110V01: Rx 880 – 900 MHz, Tx 925 – 945 MHz
426
288
Active Duplex Hybrid Combiner (Same-Band Combiner)
Active Duplex Hybrid Combiner (tunable)
880 ... 960 MHz 880 ... 960 MHz
(Same-Band
EGSM 900 Combiner)
UMTS 900
880 – 915 / 925 – 960 MHz 880 – 915 / 925 – 960 MHz
• Enables antenna and feeder sharing for two base stations in
the 900 MHz frequency band
RET = Remote Electrical Tilt
AISG = Antenna Interface Standards Group
• 12 dB gain over 20 MHz Rx bandwidth (factory tunable) CWA = Current Window Alarm
•Accessories
Very low insertion
(order loss over 20 MHz Tx bandwidth (factory
separately)
tunable) compared to standard hybrid combiners Clamp Set
• Double unit inmast

Type No. Clamp set suitable for
one housing for XPol antennas
diameter of mm | in
•734360
Suitable for indoor or outdoor applications
Typical Attenuation Curves
Port 3
•734361
Supports AISG 34 – 60 | 1.34 – 2.36
1.1 and AISG 2.0 (default)
Tuning example 78211110V01 Port 6
•734362
standard
60 – 80 | 2.36 – 3.15
Suitable for antenna RET control according to AISG/3GPP
80 – 100 | 3.15 – 3.94
Rx: 880-900 MHz, Tx: 925-945 MHz
Diagram I Port 2 ↔ Port 3
•734363
Bypass mode (LNA) to ensure
100 – 120 | 3.94 –cell
power down 120 – 140 | 4.72 – 5.51
4.72operation in case of DC
DC stop
Port 5 ↔ Port 6
734364
•734365
Built-in lightning45protection
– 125 | 1.77 – 4.92
When ordering please specify the required Tx-and Rx-frequencies
Type No.of tuning versions:
Description Port 1
Examples
78211110V01: Rx 880 – 900 MHz, Tx 925 – 945 MHz RET
78210850V01 DC stop
78211110V02: Rx 895 – 915 MHz, Tx 940 – 960 MHz50-Ohm load Port 2
78410367
Other 50-Ohm load
frequencies on request. Port 4 Port 5
1.5 W / indoor or outdoor

Technical Data
Type No. 78211110
Pass band
Rx 20 MHz within 880 ... 915 MHz (factory tunable) Diagram II Port 2 ↔ Port 3
Tx 20 MHz within 925 ... 960 MHz (factory tunable) Port 5 ↔ Port 6
Tx Insertion loss
Port 2 � Port 3 / Port 5 � Port 6 < 0.2 dB (925 – 945 MHz)* – see Diagram I and II
Isolation
Port 1 � Port 2 / Port 4 � Port 5 > 25 dB (880 – 900 MHz)*
> 65 dB (925 – 945 MHz)*
Gain 12 dB nominal
Gain ripple ±1 dB
Loss in bypass mode < 5.5 dB (DC OFF)
Return loss > 18 dB (DC ON) / > 12 dB (DC OFF)
Noise figure < 1.6 dB (+22 ... +28 °C)
Output 1-dB compression point > 11 dBm
3rd order intercept point (OIP3) > 25 dBm (typically 30 dBm)
VSWR < 1.25 (880 – 900 / 925 – 945 MHz)* Diagram III Port 1 ↔ Port 3
Port 4 ↔ Port 6
Impedance 50 Ω
Input power Port 2 < 200 W
Port 5 < 200 W
Intermodulation products < 160 dBc (5th order, with 2 x 20 W)
Environmental Characteristics
Operating temperature range –40 … +65 °C
IP rating IP67 (see note on page 2)
MTBF > 1 000 000 hours (per TMA)
EMC According to ETS 300 342-3
DC supply 9 – 19 V 9 – 30 V
Operating current per TMA 80 – 120 mA Nom. 20 mA at 9 V
(without RET) Nom. 30 mA at 30 V
Alarm management 170 – 200 mA AISG (see note on page 2) Diagram IV Port 1 ↔ Port 3
Port 4 ↔ Port 6
Mechanical Characteristics
Connectors RF 7-16 female (long neck)
AISG 8-pin female, IEC 60130-9
(Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC,
pin 7: DC return, other pins: not connected)
Mounting Wall mounting: with 4 screws (max. 8 mm diameter)
Mast mounting: with additional clamp set
Weight 6.8 kg
Dimensions (w x h x d) 369 x 209 x 68 mm
* Tuning version 78211110V01: Rx 880 – 900 MHz, Tx 925 – 945 MHz
288
427
Same-Band Combiner
880 − 890 / 925 − 935 MHz 902.5 − 915 / 947.5 − 960 MHz

in the same frequency band
Port 3
within the same frequency band Port 2
• Very low Tx/Rx insertion loss compared to standard Port 6
hybrid combiners Port 4
• Double unit for XPol antennas

• DC/AISG bypass for DTMA supply Port 5
Port 1
Tuning Diagram
Technical Data
Type No. 78210936
Pass band
BTS 1 (GSM900 / Operator 1) Rx1/Rx2 = 880 - 890 MHz, Tx1/Tx2 = 925 - 935 MHz
BTS 2 (GSM900 / Operator 2) Rx3/Rx4 = 902.5 - 915 MHz, Tx3/Tx4 = 947.5 - 960 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 < 0.5 dB, typically 0.3 dB (880 - 890 MHz) / < 0.7 dB, typically 0.4 dB (925 - 935 MHz)
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 0.7 dB, typically 0.5 dB (902.5 - 915 MHz) / < 0.5 dB, typically 0.3 dB (947.5 - 960 MHz)
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (880 - 890 / 902.5 - 915 / 925 - 935 / 947.5 - 960 MHz)
Impedance 50 Ω
Input power
Tx1 / Tx2 / Tx3 / Tx4 < 100 W / < 100 W / < 100 W / < 100 W
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 Bypass (max. 2500 mA)
Mounting Wall mounting: With 4 screws (max. 8 mm diameter)
Weight 6.9 kg
428
Same-Band Combiner
880 − 890 / 925 − 935 MHz 902.5 − 915 / 947.5 − 960 MHz

BTS 1 (GSM 900)
Diagram I (Port 1 ↔ Port 3 / Port 4 ↔ Port 6) Diagram II (Port 1 ↔ Port 3 / Port 4 ↔ Port 6)
0 0
Attenuation/dB
Attenuation/dB
-5 -0.5
880 - 890 925 - 935
Rx1/Rx2 Tx1/Tx2
-10 -1.0
880 - 890 925 - 935
Rx1/Rx2 Tx1/Tx2
-15 -1.5
-20 -2.0
-25 -2.5
-30 -3.0
-35 -3.5
-40 -4.0
-45 -4.5
-50 -5.0

870 880 890 900 910 920 930 940 950 960 970 870 880 890 900 910 920 930 940 950 960 970
Frequency/MHz Frequency/MHz
BTS 2 (GSM 900)

Diagram III (Port 2 ↔ Port 3 / Port 5 ↔ Port 6) Diagram IV (Port 2 ↔ Port 3 / Port 5 ↔ Port 6)
0 0
Attenuation/dB
Attenuation/dB
-5 -0.5
-10 -1.0
902.5 - 915 947.5 - 960 902.5 - 915 947.5 - 960
Rx3/Rx4 Tx3/Tx4 Rx3/Rx4 Tx3/Tx4
-15 -1.5
-20 -2.0
-25 -2.5
-30 -3.0
-35 -3.5
-40 -4.0
-45 -4.5
-50 -5.0
870 880 890 900 910 920 930 940 950 960 970 870 880 890 900 910 920 930 940 950 960 970
Block Diagram

- 50-Ohm load (type no. 78410367)
429
Same-Band Combiner
1710 – 1740 / 1805 – 1835 MHz 1755 – 1785 / 1850 – 1880 MHz

hybrid combiners
Tuning Diagram
Technical Data
Type No. 78211230

Pass band
BTS 1 (LTE/GSM1800 / Operator 1) Rx1/Rx2 = 1710 – 1740 MHz, Tx1/Tx2 = 1805 – 1835 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 < 0.6 dB (1710 - 1740 MHz) / < 0.5 dB (1805 - 1835 MHz)
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 0.5 dB (1755 - 1785 MHz) / < 0.6 dB (1850 - 1880 MHz)
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (1710 - 1740 / 1755 - 1785 / 1805 - 1835 / 1850 - 1880 MHz)
Impedance 50 Ω
DC/AISG transparency (switchable)
Mounting Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional
clamp set
Weight 5.5 kg
430
Same-Band Combiner
1710 – 1740 / 1805 – 1835 MHz 1755 – 1785 / 1850 – 1880 MHz

BTS 1 (LTE/GSM 1800)

BTS 2 (LTE/GSM 1800)

Diagram III (Port 2 ↔ Port 3 / Port 5 ↔ 6) Diagram IV (Port 2 ↔ Port 3 / Port 5 ↔ Port 6)
Block Diagram
LTE / LTE /
GSM 1800 GSM 1800
78211230
- 50-Ohm load (type no. 78410367)
431
Same-Band Combiner
1730 – 1750 / 1825 – 1845 MHz 1765 – 1785 / 1860 – 1880 MHz

hybrid combiners
Tuning Diagram
Technical Data
Type No. 78211235

Pass band
Insertion loss
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (1730 – 1750 / 1765 – 1785 / 1825 – 1845 / 1860 – 1880 MHz)
Impedance 50 Ω
Mounting Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional
clamp set
Weight 5.5 kg
432
Same-Band Combiner
1730 – 1750 / 1825 – 1845 MHz 1765 – 1785 / 1860 – 1880 MHz

Block Diagram
LTE / GSM 1800 LTE / GSM 1800

- 50-Ohm load (type no. 78410367)
433
Same-Band Combiner (tunable)
1710 − 1785 / 1805 − 1880 MHz 1710 − 1785 / 1805 − 1880 MHz
• Enables antenna and feeder sharing for two

base stations in the same frequency band
• Suitable for two operators with frequency
allocations within the same frequency band
• Customized 25 MHz Tx/Rx pass-band
filters
(factory tunable) available for inserting LTE/
GSM 1800 base station
Port 3
• Full pass-band (without LTE/GSM 1800
25 MHz Tx/Rx frequency blocks) available Port 1
for GSM 1800 base station Port 2
• Very low insertion loss over complete GSM Tuning Examples
Tx/Rx bandwidth compared to standard
hybrid combiners
1
• Single unit
• Suitable for indoor or outdoor applications 2
• DC/AISG by-pass for DTMA supply 3

When ordering please specify the required Tx-
and Rx frequencies e.g. (tuning example 1)
Rx1 1710 - 1758 MHz, Rx2 1760 - 1785 MHz
Tx1 1805 - 1853 MHz, Tx2 1855 - 1880 MHz
Technical Data
Type No. 78211370

Pass band
GSM 1800 Rx = 1710 - 1785 / Tx = 1805 - 1880 MHz (without assigned GSM/LTE 1800 25 MHz TX/Rx
frequency blocks and 2 MHz guard bands)
GSM/LTE 1800 Rx = 1710 ... 1785 / Tx = 1805 ... 1880 MHz (factory tunable 25 MHz frequency blocks)
Guard band 2 MHz (between Tx1/Rx1 and Tx2/Rx2) – e.g. tuning example 1:
Rx1 = 1710 - 1758 MHz and Tx1 = 1805 - 1853 MHz
Rx2 = 1760 - 1785 MHz and Tx2 = 1855 - 1880 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 2 ↔ Port 3 Rx < 1.5 dB, typ. 0.5 dB / Tx < 1.7 dB, typ. 0.5 dB)
Isolation Port 1 ↔ Port 2 > 30 dB (1805 - 1880 MHz) / > 25 dB (1710 - 1785 MHz)
Impedance 50 Ω
Input power Tx1 / Tx2 < 100 W / < 100 W
Port 1 ↔ Port 3 (default) Stop
Port 2 ↔ Port 3 (default) By-pass (max. 2500 mA)
Mounting Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: 2 clamps needed
Weight 6.6 kg
434
1710 − 1785 / 1805 − 1880 MHz 1710 − 1785 / 1805 − 1880 MHz
Typical Attenuation Curves 78211370V01

Block Diagram
- Clamp set (type no. 734360 - 734365),

- DC stop (type no. 793301) and
- 50-Ohm load (type no. 78410367)
435
1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz
• Enables antenna and feeder sharing for two base stations in the same
frequency band
• Customized 10 MHz Tx/Rx bandpass filters (factory tunable) available
for inserting a second UMTS 2100 base station Port 2
• Full pass-band (without the second UMTS 2100 10 MHz Tx/Rx Port 6 Port 1
frequency blocks) available for the first UMTS 2100 base station
• Low insertion loss over complete UMTS 2100 Tx/Rx bandwidth Port 4 Port 3
compared to standard hybrid combiners
• Suitable for indoor and outdoor applications Port 5
Tuning Examples

When ordering please specify the required Tx- and
Rx-frequencies e.g. (tuning example 1)
Rx1/Rx2 1950 - 1965 MHz, Rx3/Rx4 1970 - 1980 MHz
Tx1/Tx2 2140 - 2155 MHz, Tx3/Tx4 2160 - 2170 MHz
Technical Data
Type No. 78210925

Pass band
BTS 1 (UMTS 2100) Rx = 1920 - 1980 / Tx = 2110 - 2170 MHz
(without assigned BTS 2 10 MHz Tx/Rx frequency blocks and ± 5 MHz guard bands)
BTS 2 (UMTS 2100) Rx = 1920 ... 1980 / Tx = 2110 ... 2170 MHz
(factory tunable 10 MHz frequency blocks)
Guard band 5 MHz (between Tx1/Tx1 and Tx3/Rx3, between Tx2/Rx2 and Tx4/Rx4
e.g. tuning example 1)
Rx1 (Rx2) = 1950 - 1965 and Tx1 (Tx2) = 2140 - 2155 MHz
Rx3 (Rx4) = 1970 - 1980 and Tx3 (Rx4) = 2160 - 2170 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 < 1.2 dB - see diagram I and II for tuning example 1
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 1.2 dB - see diagram III and IV for tuning example 1
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (1920 - 1980 / 2110 - 2170 MHz)
Impedance 50 Ω
Input power
Tx1 / Tx2 / Tx3 / Tx4 < 100 W / < 100 W / < 100 W / < 100 W
Intermodulation products < -160 dBc (with 2 x 20 W)
Weight 7 kg
436
1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz

BTS 1 (UMTS 2100)
0 0
Attenuation/dB
Attenuation/dB
5 0.5
1950 – 1965 2140 – 2155
Rx Tx
10 1.0
1950 – 1965 2140 – 2155
Rx Tx
15 1.5
20 2.0
25 2.5
30 3.0
35 3.5
40 4.0
45 4.5
50 5.0
1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200

BTS 2 (UMTS 2100)
0 0
Attenuation/dB
Attenuation/dB
5 0.5
10 1.0
1970 – 1980 2160 – 2170
Rx Tx
15 1.5
1970 – 1980 2160 – 2170
Rx Tx
20 2.0
25 2.5
30 3.0
35 3.5
40 4.0
45 4.5
50 5.0
1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200
Block Diagram

- 50-Ohm load (type no. 78410367)
437
1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz
frequency band
• Customized 15 MHz Tx/Rx bandpass filters (factory tunable) available
for inserting a second UMTS 2100 base station
• Full pass-band (without the second UMTS 2100 15 MHz Tx/Rx
frequency blocks) available for the first UMTS 2100 base station
• Low insertion loss over complete UMTS 2100 Tx/Rx bandwidth
compared to standard hybrid combiners
Tuning Examples

When ordering please specify the required Tx- and
Rx-frequencies e.g. (tuning example 1)
Rx1/Rx2 1935 - 1950 MHz, Rx3/Rx4 1965 - 1980 MHz
Tx1/Tx2 2125 - 2140 MHz, Tx3/Tx4 2155 - 2170 MHz
Technical Data
Type No. 78210926

Pass band
BTS 1 (UMTS 2100) Rx = 1920 - 1980 / Tx = 2110 - 2170 MHz
(without assigned BTS 2 15 MHz Tx/Rx frequency blocks and ± 15 MHz guard bands)
BTS 2 (UMTS 2100) Rx = 1920 ... 1980 / Tx = 2110 ... 2170 MHz
(factory tunable 15 MHz frequency blocks)
Guard band 15 MHz (between Tx1/Rx1 and Tx3/Rx3, between Tx2/Rx2 and Tx4/Rx4
e.g. tuning example 1:
Rx1 (Rx2) = 1935 - 1950 and Tx1 (Tx2) = 2125 - 2140 MHz
Rx3 (Rx4) = 1965 - 1980 and Tx3 (Tx4) = 2155 - 2170 MHz
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 < 1.2 dB
Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 1.2 dB
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 28 dB (1920 - 1980 / 2110 - 2170 MHz)
Impedance 50 Ω
Input power
Tx1 / Tx2 / Tx3 / Tx4 < 100 W / < 100 W / < 100 W / < 100 W
Intermodulation products < -160 dBc (with 2 x 20 W)
Weight 7 kg
438
1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz
Typical Attenuation Curves (Tuning Example 1)

BTS 1 (UMTS 2100)
0 0
Attenuation/dB
Attenuation/dB
5 0.5
10 1.0
1935 – 1950 2125 – 2140 1935 – 1950 2125 – 2140
Rx Tx Rx Tx
15 1.5
20 2.0
25 2.5
30 3.0
35 3.5
40 4.0
45 4.5
50 5.0
1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200

BTS 2 (UMTS 2100)
0 0
Attenuation/dB
Attenuation/dB
5 0.5
10 1.0
1965 – 1980 2155 – 2170
Rx Tx
15 1.5
1965 – 1980 2155 – 2170
Rx Tx
20 2.0
25 2.5
30 3.0
35 3.5
40 4.0
45 4.5
50 5.0
1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200
Block Diagram

- 50-Ohm load (type no. 78410367)
439
Same-Band Combiner
2500 – 2520 / 2620 – 2640 MHz 2580 − 2605 MHz
frequency band
• Low insertion loss over complete LTE 2600 / TDD 2600 bandwidth compared to
standard hybrid combiners
Tuning Diagram Block Diagram
BTS 2 (TDD 1, TDD 2)

BTS 1 (Rx1, Tx1, Rx2, Tx2)
Technical Data
Type No. 78211228V01

Pass band
BTS 1 (LTE 2600) [MHz] Rx = 2500 - 2520 / Tx = 2620 - 2640
BTS 2 (TDD 2600) [MHz] TDD = 2580 - 2605
Insertion loss
Port 1 ↔ Port 3 / Port 4 ↔ Port 6 [dB] < 1.1
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 [dB] > 35
Impedance [Ω] 50
Input power per port [W] < 100
Temperature range [°C] −40 … +60
Connectors 4.3-10 female (long neck)
Lightning protection [kA] 3 kA, 10/350 μs pulse
Weight [kg | lbs] Approx. 7 | 15.47
Packing size [mm | in] 345 x 305 x 165 | 13.58 x 12 x 6.5
440
Same-Band Combiner
2500 – 2520 / 2620 – 2640 MHz 2580 − 2605 MHz
Type No. Clamp set suitable for Clamp Set

mast diameter of
734360 [mm | in] 34 – 60 | 1.34 – 2.36
734361 [mm | in] 60 – 80 | 2.36 – 3.15
734362 [mm | in] 80 – 100 | 3.15 – 3.94
734363 [mm | in] 100 – 120 | 3.94 – 4.72
734364 [mm | in] 120 – 140 | 4.72 – 5.51
734365 [mm | in] 45 – 125 | 1.77 – 4.92
Type No. Description 50-Ohm load

78210484 50-Ohm load
441
Same-Band Combiner
2500 – 2520 / 2620 – 2640 MHz 2540 – 2570 / 2660 – 2960 MHz
frequency band
• Low insertion loss over complete LTE 2600 bandwidth compared to standard
hybrid combiners
Tuning Diagram Block Diagram

Technical Data
Type No. 78211228V03

Pass band
BTS 1 (LTE 2600) [MHz] Rx = 2500 − 2520 / Tx = 2620 − 2640
BTS 2 (LTE 2600) [MHz] Rx = 2540 − 2570 / Tx = 2660 − 2690
Insertion loss
Isolation
Port 1 ↔ Port 2 / Port 4 ↔ Port 5 [dB] > 35
Impedance [Ω] 50
Input power Tx1 / Tx2 / Tx3 / Tx4 [W] < 100 / < 100 / < 100 / < 100
Temperature range [°C] −40 … +60
Connectors 4.3-10 female (long neck)
DC/AISG transparency (factory switchable)
Lightning protection [kA] 3 kA, 10/350 μs pulse
Weight [kg | lbs] Approx. 7 | 15.47
Packing size [mm | in] 345 x 305 x 165 | 13.58 x 12 x 6.5
442
Same-Band Combiner
2500 – 2520 / 2620 – 2640 MHz 2540 – 2570 / 2660 – 2960 MHz
Type No. Clamp set suitable for Clamp Set

mast diameter of
734360 [mm | in] 34 – 60 | 1.34 – 2.36
734361 [mm | in] 60 – 80 | 2.36 – 3.15
734362 [mm | in] 80 – 100 | 3.15 – 3.94
734363 [mm | in] 100 – 120 | 3.94 – 4.72
734364 [mm | in] 120 – 140 | 4.72 – 5.51
734365 [mm | in] 45 – 125 | 1.77 – 4.92
Type No. Description 50-Ohm load

78210484 50-Ohm load
443
3 dB Coupler
698 − 2690 MHz
Port 1
• Can be used for the decoupled combining of 2 transmitters onto
a common antenna with frequency spacing as narrow as desired
(3 dB loss) - see application example 1 Port 3
two antennas with frequency spacing as narrow as desired - see
application example 2
• Can be used as a decoupled 2-way splitter - see application
example 3
• Suitable for indoor or outdoor applications Port 2
• DC/AISG by-pass
Port 4
Technical Data
Type No. 78210524

Attenuation
Port 1 ↔ Port 2 3.1 ±0.5 dB
Port 1 ↔ Port 3 3.1 ±0.5 dB
Port 2 ↔ Port 3 See diagram
Directivity > 20 dB
VSWR < 1.25
Impedance 50 Ω
Input power < 150 W at each input port
DC/AISG transparency By-pass between Port 1 ↔ Port 3 / Port 2 ↔ Port 4
(max. 2500 mA)
Mounting With 4 screws (max. 6.5 mm diameter)
Weight 1.5 kg
Dimensions (w x h x d) 205.4 x 60 x 104 mm
(without connectors and mounting feet)
Note:
VSWR and attenuation values only valid if all ports are terminated with 50-Ohm loads.
- DC stop (type no. 78210850V01) and

- 50-Ohm load (type no. 78410367 or 78210474)
444
3 dB Coupler
698 − 2690 MHz
- DC stop (type no. 78210850V01) and

- 50-Ohm load (type no. 78410367 or 78210474)
445
3 dB Coupler
698 – 2690 MHz
• Can be used for the decoupled combining of 2 transmitters onto a Port 3
common antenna with frequency spacing as narrow as desired
(3 dB loss) - see application example 1
two antennas with frequency spacing as narrow as desired - see Port 4
application example 2
• Can be used as a decoupled 2-way splitter - see application
example 3
• Can be used as a frequency-independant 90° phase shifter
(90° Hybrid)
Port 1
• DC/AISG by-pass Port 2
Technical Data
Type No. 78210525

Frequency range 698 – 2690 MHz Accessories (order separately)
Attenuation
Type No. Description
Port 1 ↔ Port 3 3 ±0.5 dB
Port 1 ↔ Port 4 3 ±0.5 dB 78210850V01 DC stop
Port 1 ↔ Port 2 > 30 dB 78210474 50-Ohm load (80 W)
Directivity > 28 dB 78410367 50-Ohm load (1.5 W)
Return loss > 30 dB 78210526 Mounting kit
Impedance 50 Ω
Input power < 1000 W at each input port DC stop 50-Ohm load 50-Ohm load
DC/AISG transparency By-pass between Port 1 ↔ Port 4 / Port 2 ↔ Port 3 Mounting kit
(max. 2500 mA)
Weight 0.7 kg
Dimensions (w x h x d) 158 x 55 x 60 mm
(without connectors)
Note:
VSWR and attenuation values only valid if all ports are terminated with 50-Ohm-loads.
446
3 dB Coupler
698 – 2690 MHz
447
3 dB Coupler
Hybrid Combiner 2:2
800 − 2200 MHz
The 3-dB coupler can be used:
• as a decoupled power splitter with a ratio of 1:1,
• for the decoupled combining of two transmitters with frequency
spacing as narrow as desired (at 3 dB loss),
• for the decoupled combining of two receivers with frequency
spacing as narrow as desired,
• for the decoupled combining of two transmitter/receiver units,
whose integrated duplexers are within the same frequency
range,
• as a frequency-independent 90° phase shifter,
• as a combiner component.
Function:
The 3-dB coupler has four ports, two of which are decoupled
from each other. For example effective power entering into port 1
is distributed into ports 2 and 3. Port 4 is decoupled and without
power if ports 2 and 3 are ideally matched. In practice an absorber
of suitable power at port 4 is to be planned in accordance with the
mismatch of ports 2 and 3.
Decoupled combining can be achieved via the diagonally opposite
ports 2 and 3 or 1 and 4.
Technical Data
Type No. 793554

Attenuation 1 ↔ 2 / ↔ 3 3 ±1.2 dB (see diagram I)
Attenuation 2 ↔ 3 See diagram II
Directivity > 20 dB
VSWR < 1.2
Impedance 50 Ω
Input power < 300 W total power at two inputs,
with max. 200 W at one input
Intermodulation products <-160 dBc (3rd order; with 2 x 20 W)
Application Indoor and outdoor (IP66)
Mounting With 2 screws (max. 5.5 mm diameter)
Weight 1.3 kg
Dimensions (w x h x d) 104.9 x 50.2 x 93.9 mm (including connectors)
Note:
VSWR and attenuation values are measured when the remaining ports are terminated
with 50-Ω loads
448
Filters & System Components
Filters
Smart Bias Tees
Filters & System Components DC-Stops
Attenuators
50 Ω Loads
450

Kathrein 2017 Same-Band Combiner and Hybrid Combiner Types

Uploaded by

Copyright:

Available Formats

Kathrein 2017 Same-Band Combiner and Hybrid Combiner Types

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kathrein 2017 Same-Band Combiner and Hybrid Combiner Types

Uploaded by

Copyright:

Available Formats

Summary of Same-Band Combiner and

Hybrid Combiner Types

Same-Band and Hybrid Combiners

Type No. 78210500

Same-Band and Hybrid Combiners

Max. input power per port

• Designed for the decoupled combining of 2 transmitter

* Valid if all ports are terminated with 50-Ω loads.

Max. input power per port

Mounted horizontally Mounted vertically

• Designed for the decoupled combining of 2 transmitter

• Suitable for indoor or outdoor applications

Same-Band and Hybrid Combiners

* Valid if all ports are terminated with 50-Ohm loads.

Max. input power per port

Mounted horizontally Mounted vertically

• Designed for the decoupled combining of 2 transmitter

Type No. 78210506

• Point of Interface (POI) for coverage solutions

Same-Band and Hybrid Combiners

Type No. 78211141 78211142 78211143 78211144

Temperature range -40 ... +60 °C

2170 2170 2170 2170

• Designed for the decoupled combining of 3 transmitter

Type No. 78211216

Same-Band and Hybrid Combiners

• DC/AISG bypass Output 4

Technical Data Input 3

Type No. 78210534 Input 4

Accessories (order separately)

• Enables antenna and feeder sharing for two base

Same-Band and Hybrid Combiners

Type No. 78211237

- Clamp set (type no. 734360 - 734365) and

880 − 960 MHz 880 − 960 MHz

• Enables antenna and feeder sharing for two base stations

• Suitable for indoor or outdoor applications Port 1

880 − 960 MHz 880 − 960 MHz

Accessories (order separately) Clamp Set

734363 100 – 120 | 3.94 – 4.72 10

734365 45 – 125 | 1.77 – 4.92 20

Type No. Description 35

78210850V01 DC stop 50-Ohm load

Same-Band and Hybrid Combiners

Diagram III Port 2 Port 3

Diagram IV Port 2 Port 3

• Double unit inmast

Same-Band and Hybrid Combiners

• Enables antenna and feeder sharing for two base stations

• Double unit for XPol antennas

Typical Attenuation Curves

Same-Band and Hybrid Combiners

BTS 2 (GSM 900)

- Clamp set (type no. 734360 - 734365) and

• Enables antenna and feeder sharing for two base

Type No. 78211230

Typical Attenuation Curves

Same-Band and Hybrid Combiners

BTS 2 (LTE/GSM 1800)

• Enables antenna and feeder sharing for two base