Trade Electrician: Syllabus Breakup Daily

Trade
‐ELECTRICIAN
Syllabus Breakup Daily
Week Day Subject Theory (02 hours) Practical (05 hours)
Visit various sections of the
1 Scope of the electrician trade. institutes and location of
electrical installations. (05 hrs)
Theory
Identify safety symbols and
2 Safety rules and safety signs.
hazards. (05 Hrs)
Classification of Unit System Fundamental
Preventivemeasures for
and Derived Units F.P.S, C.G.S, M.K.S and
W/Shop electrical accidents and practice
3 SI Units ,Measurement Units and
calculation steps to be taken in such
Conversion,Factors, HCF, LCM and
accidents. (05 hrs)
Problems
1
Engineering Drawing – Introduction
Introduction to Engineering Drawing and
Drawing Instruments – Practice safe methods of fire
Engg.
4 ‐> Conventions fighting in case of electrical fire.
Drawing
‐> Viewing of engineering drawing sheets. (05 hrs)
‐> Method of Folding of printed Drawing
sheet as per BIS SP: 46‐2003
Behavioural Skill‐Creating a focused and Theory : 3 hrs ‐ Types and
5 ES responsible learning envirnment‐Chart working of fire extinguishers.
paper Activity. Extra curricular activity : 2 hrs
Self‐awareness and confidence building,
6 ES display professionalism at the institute Use of fire extinguishers. (05 Hrs)
and work place
Total Week Hrs : 40 , Theory : 7 Hrs , Practical : 25 hrs , Engg. Drawing : 2 Hrs , W/S Cal Sc : 2 Hrs , ES : 4 Hrs
Trade ‐ELECTRICIAN
First aid safety practice. Hazard Practice elementary first aid. (05
1
identification and prevention. hrs)
Theory
Rescue a person and
2 Personal safety and factory safety. practiceartificial respiration. (05
Hrs)
Fractions – Addition, Subtraction,
Multiplication and Division
W/Shop ‐> Decimal Fractions ‐ Addition, Disposal procedure of waste
3
calculation Subtraction, Multiplication materials. (05 Hrs)
and Division
‐> Solving Problems by using calculator
Drawing Instrument
‐> Drawing board, T‐square, Drafter
2 (Drafting M/c), Set squares, Protector,
Engg. Use of personal protective
4 Drawing Instrument Box (Compass,
Drawing equipments. (05 hrs)
Dividers, Scale, Diagonal Scales etc.),
pencils of different grades, Drawing pins/
Clips.
Increased Social initiations relationships
and networks . Acceptance of peers from Theory : 3 hrs ‐Response to
different cultures and social groups and emergencies e.g. power failure,
5 ES
work with them . Collaboration with team system failure and fire etc.
to priroritise the common goal and Extra curricular activity : 2 hrs
compromise individual prirorities.
Characteristic of a responsible citizen‐
Display the same by respecting self, Practice on cleanliness and
6 ES
others, environment, care for duty and procedure to maintain it. (05 hrs)
value for time.
Concept of Standards and advantages of Identify trade tools and
1
BIS/ISI. machineries. (5 Hrs)
Theory
Identify trade tools and
2 Trade tools specifications.
machineries. (5 Hrs)
Square and Square Root
Practice safe methods of lifting
W/Shop ‐> Simple problems using calculator
3 and handling of tools &
calculation ‐> Application of Pythagoras Theorem and
equipment. (05 Hrs)
related problems
Select proper tools for operation
3 Engg. Free hand drawing of –
4 and precautions in operation. (05
Drawing ‐> Lines, polygons, ellipse etc.
Hrs)
Adopting best practices and aspire to Theory : 3 hrs ‐ Introduction to
5 ES follow success stories of individual for National Electrical Code‐2011.
personal development. Extra curricular activity : 2 hrs
English literacy:‐Importance of learning Care & maintenance of trade
6 ES
english tools. (05 Hrs)
Allied trades: Introduction to fitting tools, Operations of allied trade tools.
1
safety precautions. (05 Hrs)
Theory
Workshop practice on filing and
2 Description of files, hammers, chisels
hacksawing. (5 Hrs)
W/Shop Workshop practice on filing and
3 Monthly Test WCS
calculation hacksawing. (5 Hrs)
4
Engg. Prepare hand coil winding
4 Monthly Test ED
Drawing assembly. ( 5 Hrs)
5 ES Monthly Test ES Monthly Test theory
Different naming words, word used for
6 ES replacing names, action words, describing Monthly Test Practical
people, place and their use.
Practice on preparing T‐joint,
hacksaw frames, blades, their
1 straight joint and dovetail joint
specification and grades
on wooden blocks. (15Hrs)
Theory
Practice on preparing T‐joint,
2 Marking tools description and use. straight joint and dovetail joint
on wooden blocks. (15Hrs)
Ratio and Proportions
Practice sawing, planing, drilling
W/Shop ‐> Direct and Indirect proportion
3 and assembling for making a
calculation ‐> Percentage
wooden switchboard. (15Hrs)
‐> Changing percentage to decimal
5 Practice sawing, planing, drilling
Engg. Geometrical figures and blocks with
4 and assembling for making a
Drawing dimension
Theory : 3 hrs ‐ Types of drills,
Introduction to punctuation‐comma, full description & drilling machines.
5 ES
stop, question mark. Various wooden joints.
Extra curricular activity : 2 hrs
Practice sawing, planing, drilling
6 ES Singular plural and assembling for making a
Practice in marking and cutting
of straight and curved pieces in
Marking tools; calipers Dividers, Surface
1 metal sheets, making holes,
plates, Angle plates, Scribers,
securing by screw and riveting.
(10 Hrs)
Theory
Practice in marking and cutting
of straight and curved pieces in
punches, surface gauges Types, Uses,
2 metal sheets, making holes,
Care and maintenance.
securing by screw and riveting.
(10 Hrs)
Workshop practice on drilling,
Types of metals
W/Shop chipping, internal and external
3 ‐> Physical and Mechanical Properties of
calculation threading of different sizes.
6 metals
(20Hrs)
Engg. Transferring measurement from the given chipping, internal and external
4
Drawing object to the free hand sketches. threading of different sizes.
(20Hrs)
Theory : 3 hrs ‐ Sheet metal
Change of tense‐simple present, past; tools: Description of marking &
5 ES
present, past progressive cutting tools.
Construction of simple senteces‐kinds of chipping, internal and external
6 ES
sentences threading of different sizes.
(20Hrs)
chipping, internal and external
1 Types of rivets and rivetedjoints.
threading of different sizes.
Theory
(20Hrs)
Practice of making square holes
2 Use of thread gauge.
in crank handle. (5 Hrs)
W/Shop Types of ferrous and non‐ferrous metals Prepare an open box from metal
3
calculation ‐> Introduction of iron and cast iron sheet. (15 Hrs)
7
Solid objects – Cube, Cuboids, Cone,
Engg. Prepare an open box from metal
4 Prism, Pyramid, Frustum of Cone with
Drawing sheet. (15 Hrs)
dimensions.
Theory : 3 hrs ‐ Description of
Usege of appropriate words to express carpenter’s tools Care and
5 ES
themselves maintenance of tools.
Prepare an open box from metal
6 ES Greetings & self indroduction
sheet. (15 Hrs)
Prepare terminations of cable
Fundamentals of electricity, definitions,
1 ends,Practice on skinning,
units & effects of electric current.
Theory twisting and crimping.
Conductors and insulators.Conducting Practice on skinning, twisting and
2
materials and their comparison. crimping.
Identify various types of cables
W/Shop
3 Monthly Test WCS and measure conductor size
calculation
using SWG and micrometer.
8 Identify various types of cables
Engg.
4 Monthly Test ED and measure conductor size
Drawing
using SWG and micrometer.
6 ES Asking & self indtroduction Monthly Test Practical
Conducting materials and their
1 Joints in electrical conductors.
comparison.
Theory
Conducting materials and their
2 Joints in electrical conductors.
comparison.
Difference between iron and steel, alloy
W/Shop steel and carbon steel Conducting materials and their
3
calculation ‐> Properties and uses of rubber, timber comparison.
9 and insulating materials
Free hand drawing of hand tools and
Engg. Make britannia straight,
4 measuring tools, simple fasteners (nuts,
Drawing britannia Tee and rat tail joints.
bolts, rivets etc.) trade related sketches
Theory : 3 hrs ‐Techniques of
5 ES Asking & responding to question soldering. Extra
curricular activity : 2 hrs
Make britannia straight,
6 ES Sharing information with others
britannia Tee and rat tail joints.
1 Techniques of soldering.
Theory
2 Types of solders and flux.
W/Shop Mass, volume, density, weight & specific Practice in Soldering of joints /

3
calculation gravity lugs.
Lines
‐> Definition, types and applications in
10 Engg. drawing as per BIS: 46‐2003 Practice in Soldering of joints /
4
Drawing ‐> Classification of lines (Hidden, centre, lugs.
construction, extension, Dimension,
Section)
Theory : 3 hrs ‐Types of solders
5 ES Formal and informal communication and flux. Extra
Speak and provide information about Practice in Soldering of joints /
6 ES
workplace lugs.
Identify various parts, skinning
1 Underground cables:Description, and dressing of underground
cable. (15 Hrs)
Theory
Identify various parts,
2 Underground cables: types, various joints skinningand dressing of
underground cable. (15 Hrs)
Related problems for mass, volume, Identify various parts,
W/Shop
3 density, weight & skinningand dressing of
calculation
specific gravity underground cable. (15 Hrs)
Drawing lines of given length (Straight,
11 curved)
Engg. Make straight joint of different
4 ‐> Drawing of parallel lines, perpendicular
Drawing types of underground cable.
line
‐> Methods of Division of line segment
Theory : 3 hrs ‐ testing
Discussions on current happenings. Self, procedure of underground
5 ES
Work, Environment cables Extra curricular activity : 2
hrs
Make straight joint of different
6 ES Simple writing skills
types of underground cable.
Make straight joint of different
1 Cable insulation & voltage grades
types of underground cable.
Theory
Test insulation resistance of
2 Cable insulation & voltage grades underground cable using
megger. (05 hrs)
Rest, motion, speed, velocity, difference Test underground cables
W/Shop
3 between speed and forfaults and remove the fault.
calculation
12 velocity, acceleration and retardation (15 Hrs)
Drawing of Geometrical figures: Test underground cables
Engg.
4 Definition, nomenclature and practice of forfaults and remove the fault.
Drawing
– (15 Hrs)
Theory : 3 hrs ‐Precautions in
Communication Skills:‐Interview
5 ES using various types of cables.
Skill/Confidence Building
Test underground cables
Professionalism and display of same at
6 ES forfaults and remove the fault.
the institute and work place
(15 Hrs)
Practice on measurement of
parameters in combinational
Ohm’s Law; Simple electrical circuits and electrical circuit by applying
1
problems. Ohm’s Law for different resistor
values and voltage sources and
analyse by drawing graphs
Theory
Practice on measurement of
parameters in combinational
electrical circuit by applying
2 Kirchoff’s Laws and applications.
Ohm’s Law for different resistor
values and voltage sources and
analyse by drawing graphs
13
Measure current and voltage in
W/Shop
3 Quarterly Test WCS electrical circuits to verify
calculation
Kirchhoff’s Law (10 Hrs)
Measure current and voltage in
Engg.
4 Quarterly Test ED electrical circuits to verify
Drawing
Kirchhoff’s Law (10 Hrs)
5 ES Quarterly Test ES Quarterly Test theory
Understand the usage of appropriate
6 ES words to express themselves Quarterly Test Practical
communicate effectively on telephone.
Verify laws of series and parallel
1 Series and parallel circuits. circuits with voltage source in
different combinations. (05Hrs)
Theory
Measure voltage and current
Open and short circuits in series and
2 against individual resistance in
parallel networks.
electrical circuit (10 hrs)
Measure voltage and current
W/Shop
3 Related problems on speed and velocity against individual resistance in
calculation
electrical circuit (10 hrs)
14 easure current and voltage and
Engg.
4 Triangle: different types analyse the effects of shorts and
Drawing
opens in series circuit. (05 Hrs)
Theory : 3 hrs ‐Open and short
Manage personal hygiene and
circuits in series and parallel
presentation positive body
5 ES networks. .
language:adopt and use it appropriately
Parents instructor meeting: 2
to build a positive impression
hrs
Different spatial zones: Understanding Measure current and voltage and
6 ES and need to maintain it, create safe zones analyse the effects of shorts and
for communication opens in parallel circuit. (05 Hrs)
Laws of Resistance and various types of
Measure resistance using voltage
1 resistors. Wheatstone bridge; principle
drop method. (5 Hrs)
and its applications.
Theory
Wheatstone bridge; principle and its
Measure resistance using
2 applications. Effect of variation of
wheatstone bridge. (5 Hrs)
temperature on resistance.
Potential energy, Kinetic Energy and
W/Shop Determine the thermal effect of
3 related problems with
calculation electric current. (5 Hrs)
related problems
Engg. Rectangle, Square, Rhombus, Determine the change in
15 4
Drawing Parallelogram resistance due to temperature.
Theory : 3 hrs ‐Different
methods of measuring the values
Maintainig appropriate eye‐contact in
5 ES of resistance. Series and parallel
building trust and confidence
combinations of resistors.
Verify the characteristics of
Impact of touch in a formal environment.
6 ES series parallel combination of
Acceptable and unacceptable touch.
resistors. (5 Hrs)
Magnetic terms, magnetic materials and Determine the poles and plot the
1
properties of magnet. field of a magnet bar.
Theory
Determine the poles and plot the
2 Principles and laws of electro‐magnetism.
field of a magnet bar.
Wind a solenoid and determine
W/Shop Work, power, energy, HP, IHP, BHP and
3 the magnetic effect of electric
calculation efficiency
16 current.
Engg. Measure induced emf due to
4 Circle and its elements
Drawing change in magnetic field.
Time mangagement and planning skills Theory : 3 hrs ‐Self and mutually
5 ES interview skills its phases & ways to crack induced EMFs.
interview Extra curricular activity : 2 hrs
Handing setbacks/rejection and recover Determine direction of induced
6 ES
from it with an action plan. emf and current. (06 hrs)
Electrostatics: Capacitor‐ Different types, Practice on generation of
1
functions, grouping and uses. mutually induced emf. (08 hrs)
Theory Measure the resistance,
Inductive and capacitive reactance, their
impedance and determine
2 effect on AC circuit and related vector
inductance of choke coils in
concepts.
different combinations.
Identify various types of
W/Shop
3 Monthly Test WCS capacitors, charging / discharging
calculation
17 and testing. (05 Hrs)
Group the given capacitors to get
Engg.
4 Monthly Test ED the required capacity and
Drawing
voltage rating. (05 Hrs)
5 ES Monthly test ES Monthly Test theory
Developing strongs professional
6 ES contract/network to gain support inl Monthly Test Practical
learining process and career as a whole
Measure current, voltage and PF
Comparison and Advantages of DC and AC and determine the
1
systems. characteristics of RL, RC and RLC
in AC series circuits.
Theory
Related terms frequency, Instantaneous Measure current, voltage and PF
value, R.M.S. value Average value, Peak and determine the
2
factor, form factor, power factor and characteristics of RL, RC and RLC
Impedance etc. in AC series circuits.
Concept of heat and temperature, effects
of heat, difference
Measure the resonance
between heat and temperature
W/Shop frequency in AC series circuit and
3 ‐> Scales of temperature, Celsius,
calculation determine its effect on the
Farenhieght,Kelvin and
circuit. (07 hrs)
Conversion between scales of
temperature
18 Different polygon and their values of
Engg. and determine the
4 included angles. Inscribed and
Drawing characteristics of RL, RC and RLC
circumscribed polygons
in AC parallel circuits. (08 Hrs)
Theory : 3 hrs ‐Related terms
Literacy:‐ Indtroduction to computers and frequency, Instantaneous value,
its applications hardware and periphersal, R.M.S. value Average value, Peak
5 ES
srarting and shutting down of computer, factor, form factor, power factor
basic ofn computer networks. and Impedance etc.
Basics of Operating System, Types of
operating systems, user interface of
widows OS/ latest create, copy move and
and determine the
6 ES delete files and folders, use of external
characteristics of RL, RC and RLC
memory like pen drive, CD,DVD etc,
in AC parallel circuits.
introduction toinbuilt windows apps,
tools and features.
Measure the resonance
frequency in AC parallel circuit
1 Sine wave, phase and phase difference.
and determine its effects on the
circuit.
Theory Measure power, energy for
lagging and leading power
2 Active and Reactive power. factors in single phase circuits
and compare characteristic
graphically.
Temperature measuring instruments, Measure power, energy for
types of thermometer, lagging and leading power
W/Shop
3 pyrometer and transmission of heat ‐ factors in single phase circuits
19 calculation
Conduction, convection and compare characteristic
and radiation graphically.
Measure Current, voltage,
Engg. Lettering & Numbering –
4 power, energy and power factor
Drawing ‐> Single Stroke
in three phase circuits.
Basic operating of word processing, Theory : 3 hrs ‐Single Phase and
creating, opening and closing documents, three‐phase system. Problems
5 ES
use of shortcuts, creating and editing of on A.C. circuits.
text, formatting the text Extra curricular activity : 2 hrs
Creating simple documents like resum, Practice improvement of PF by
6 ES letter writing, job application etc., use of capacitor in three phase
printing document circuit.
Ascertain use of neutral by
identifying wires of a 3‐phase 4
1 Advantages of AC poly‐phase system. wire system and find the phase
sequence using phase sequence
meter. (10 Hrs)
Theory
Ascertain use of neutral by
identifying wires of a 3‐phase 4
Concept of three‐phase Star and Delta
2 wire system and find the phase
connection.
sequence using phase sequence
meter. (10 Hrs)
Co‐efficient of linear expansion and Determine effect of broken
W/Shop
3 related problems with neutral wire in three phase four
calculation
assignments wire system.(05 hrs)
Determine the relationship
20
Engg. Lettering & Numbering – between Line and Phase values
4
Drawing Double Stroke for star and delta connections.
(10Hrs)
Basic of excel worksheet and its
Theory : 3 hrs ‐Concept of three‐
importance creating simple worksheets
5 ES phase Star and Delta connection.
adding and average function, printing of
simple excel sheet.
Indroduction to world wide web. (www)
Determine the relationship
usefull websides web browser‐usege,
between Line and Phase values
6 ES search engine etc. Using popular sites like
for star and delta connections.
bharat skills, skill traing related govt.
(10Hrs)
portals, nokari.com, and other job portals.
Line and phase voltage, current and Measure the Power of three
1 power in a 3 phase circuits with balanced phase circuit for balanced and
and unbalanced load. unbalanced loads. (15 Hrs)
Theory
current and power in a 3 phase circuits Measure the Power of three
2 with balanced and unbalanced load.Phase phase circuit for balanced and
sequence meter. unbalanced loads. (15 Hrs)
Measure the Power of three
W/Shop
3 Monthly Test WCS phase circuit for balanced and
calculation
unbalanced loads. (15 Hrs)
Measure current and voltage of
21 two phases in case of one phase
Engg.
4 Monthly Test ED is short‐circuited in three phase
Drawing
four wire system and compare
with healthy system.
Cits Applications , apprenticeship portal
6 ES (naps), resize images, singing up, online Monthly Test Practical
fund transfer, using UPI gateway
Chemical effectof electric current and
1 Use of various types of cells.
Laws of electrolysis.
Theory Practice on grouping of cells for
Explanation of Anodes and cathodes.
specified voltage and current
2 Types of cells, advantages / disadvantages
under different conditions and
and their applications.
care.
Practice on grouping of cells for
Problem of Heat loss and heat gain with
W/Shop specified voltage and current
3 assignments
calculation under different conditions and
‐> Thermal conductivity and insulators
care.
22 Practice on grouping of cells for
Engg. Lettering & Numbering – specified voltage and current
4
Drawing Inclined. under different conditions and
care.
Creating and using an email account like Theory : 3 hrs ‐ Lead acid cell;
gmail, and any other, usages of cc and Principle of operation and
5 ES
bcc, attaching documents checking email components.
and composing email Extra curricular activity : 2 hrs
Scaning QR/AR code, sharing bast
Prepare and practice on battery
prictices and downloading trade Related
6 ES charging and details of charging
videos using Wi‐Fi, fund Transfer through
circuit. (12 Hrs)
app like BHIM.
Types of battery charging, Safety Prepare and practice on battery
1 precautions, test equipment and charging and details of charging
maintenance. circuit. (12 Hrs)
Theory
Prepare and practice on battery
Basic principles of Electro‐plating and
2 charging and details of charging
cathodic protection
circuit.
Boiling point and melting point of
different metals and Practice on routine, care/
W/Shop
3 Nonmetals maintenance and testing of
calculation
‐> Concept of pressure and its units in batteries.
different system
Dimensioning and its Practice
23 ‐> Definition, types and methods of
Determine the number of solar
Engg. dimensioning (functional, non‐functional
4 cells in series / parallel for given
Drawing and auxiliary)
power requirement.
‐> Position of dimensioning
(Unidirectional, Aligned)
Theory : 3 hrs ‐ Grouping of cells
for specified voltage and current.
Enterpreneur skills:‐ Need of becoming
5 ES Principle and operation of solar
entrepreneur
cell. Extra
Determine the number of solar
6 ES Ways to becoming a good entrepreneur cells in series / parallel for given
power requirement.
I.E. rules on electrical wiring. Types of Identify various conduits and
1
domestic and industrial wirings. different electrical accessories.
Theory
Study of wiring accessories e.g. switches, Identify various conduits and
2
fuses, relays, MCB, ELCB, MCCB etc. different electrical accessories.
Introduction and uses of electricity,
molecule, atom, how
Practice cutting, threading of
W/Shop electricity is produced, electric current
3 different sizes & laying
calculation AC, DC and their
Installations.
comparison, voltage , resistance and their
units
24 Types of arrowhead
Engg. ‐> Leader line with text
4 different sizes & laying
Drawing ‐> Symbols preceding the value of
Installations.
dimension and dimensional tolerance.
Theory : 3 hrs ‐ Study of wiring
Enabling environment available to accessories e.g. switches, fuses,
5 ES
vecome an entrepreneur relays, MCB, ELCB, MCCB etc.
Different Govt. institutions/schemes
promoting entreprenur viz., Gramin bank,
6 ES different sizes & laying
PMMY‐MUDRA loan, DIC, SIDA SISI, NSIC,
Installations.
SIDO.
Prepare test boards / extension
boards and mount accessories
Study of wiring accessories e.g. switches,
1 like lamp holders, various
fuses, relays, MCB, ELCB, MCCB etc.
switches, sockets, fuses, relays,
MCB, ELCB, MCCB etc.
Theory
Principle of laying out of domestic boards and mount accessories
2 wiring.Grading of cables and current like lamp holders, various
ratings. switches, sockets, fuses, relays,
Conductor, Insulator, types of Prepare test boards / extension
connections‐ Series and boards and mount accessories
W/Shop
3 Parallel, like lamp holders, various
calculation
‐> Ohm’s Law, relation between VIR & switches, sockets, fuses, relays,
25 related problems MCB, ELCB, MCCB etc.
Sizes and layout of drawing sheets Prepare test boards / extension
‐> Selection of sizes boards and mount accessories
Engg.
4 ‐> Title Block, its position and content like lamp holders, various
Drawing
‐> Item Reference on Drawing Sheet (Item switches, sockets, fuses, relays,
list) MCB, ELCB, MCCB etc.
Theory : 3 hrs ‐ Voltage drop
Day to day monitoring mechanism for
5 ES concept. Extra
maintaing an enterprise.
boards and mount accessories
Different Government shcems supporting
6 ES like lamp holders, various
entrepreneurship.
switches, sockets, fuses, relays,
Draw layouts and practice in PVC
Casing‐capping, Conduit wiring
PVC conduit and Casing‐capping wiring
1 with minimum to more number
system.
of points of minimum 15 mtr
length.
Theory
Draw layouts and practice in PVC
Casing‐capping, Conduit wiring
2 Different types of wiring with minimum to more number
of points of minimum 15 mtr
length.
Wire up PVC conduit wiring to
26 W/Shop
3 Quarterly Test WCS control one lamp from two
calculation
different places.
Engg.
4 Quarterly Test ED control one lamp from two
Drawing
different places.
Examples of successful and unsuccessful
6 ES Quarterly Test Practical
entreprenurs.
Power, control, Communication and
1 control one lamp from three
entertainment wiring.
different places. (10 Hrs)
Theory
2 Wiring circuits planning, control one lamp from three
different places. (10 Hrs)
Wire up PVC conduit wiring and
Electrical power, energy and their units,
W/Shop practice control of sockets and
3 calculation with
calculation lamps in different combinations
assignments
using switching concepts.
27 Method of presentation of Engg. Drawing
Engg. ‐> Pictorial View combinations using switching
4
Drawing ‐> Orthographic View concepts.
‐> Isometric View
Theory : 3 hrs ‐ permissible load
Maintaning efficiency at workplace:‐ in sub‐circuit and main circuit.
5 ES
Factors affecting productivity Parents instructor meeting: 2
hrs
combinations using switching
6 ES Improving productivity
concepts.
Wire up the consumers main
1 Estimation of load, cable size, board with ICDP switch and
distribution fuse box. (10 Hrs)
Theory
Wire up the consumers main
2 Estimation of load, cable size, board with ICDP switch and
distribution fuse box. (10 Hrs)
Magnetic induction, self and mutual
inductance and EMF Wire up the consumers main
W/Shop
3 generation board with ICDP switch and
calculation
‐> Electrical Power, HP, Energy and units distribution fuse box. (10 Hrs)
of electrical energy
Symbolic representation – different Wire up the consumers main
Engg.
4 symbols used in the trades board with ICDP switch and
Drawing
‐> Fastener (Rivets, Bolts and Nuts) distribution fuse box. (10 Hrs)
28
Personal finance literacy planning, saving,
Theory : 3 hrs ‐ bill of material
tax govt. shcems for financial safety e.g.
5 ES and cost. Extra
Pradhan Mantri Jeevan Jyoti Bima Yojana
(PMJJBY) etc.
Occupational Safety, Health and
environment Educaiton:‐Introduction ton
occupational safety & health at work
place, occupational hygiene. Basuc Estimate the cost/bill of material
6 ES Hazards, chemical, physical (elecrical. for wiring of hostel/ residential
Temperature, illumination) ergonomic, building and workshop.
biological, vibro acoustic, mechanical,
psychoscial hazards, prevention of
hazards
Estimate the cost/bill of material
Inspection and testing of wiring
1 for wiring of hostel/ residential
installations.
building and workshop.
Theory
Practice wiring of hostel and
Inspection and testing of wiring
2 residential building as per IE
installations.
rules.
Area and perimeter of square, rectangle Practice wiring of hostel and
W/Shop
3 and parallelogram residential building as per IE
calculation
‐> Area an Perimeter of Triangle rules.
29 Practice wiring of hostel and
Engg. Bars and profile sections
4 residential building as per IE
Drawing ‐> Weld, Brazed and soldered joints
rules.
Theory : 3 hrs ‐ Special wiring
Different types of personal protective
circuit e.g. godown, tunnel and
5 ES eauipment (PPE), Accident prevention
workshop etc.
techniques
Care of injured & sick at the workplace
Practice wiring of institute and
6 ES first‐acid & transportation of sick person
workshop as per IE rules.
Basic provisions of safety & health
Special wiring circuit e.g. godown, tunnel Practice wiring of institute and
1
and workshop etc. workshop as per IE rules.
Theory
Special wiring circuit e.g. godown, tunnel Practice wiring of institute and
2
and workshop etc. workshop as per IE rules.
Practice testing / fault detection
W/Shop
3 Monthly Test WCS of domestic and industrial wiring
calculation
installation and repair.
Practice testing / fault detection
Engg.
4 Monthly Test ED of domestic and industrial wiring
Drawing
installation and repair. (15 Hrs)
30
Introduction to environment, ecosystem
and factors causing imbalace, polution
and pollutant including liquid, gageous,
solid and hazardous waste, protecting the
6 ES environment‐energy , Monthly Test Practical
conservation,ground water, global
warming, responsibility about the
environment, segregation and disposal of
waste
Prepare pipe earthing and
1 Importance of Earthing. Plate earthing measure earth resistance by
earth tester / megger. (10 Hrs)
Theory
Prepare pipe earthing and
pipe earthing methods and IEE
2 measure earth resistance by
regulations.
Area and Perimeter of Circle, Semi‐circle , Prepare plate earthing and
W/Shop
3 circular ring, measure earth resistance by
calculation
sector of circle, hexagon and ellipse earth tester / megger. (10 Hrs)
Prepare plate earthing and
Engg. Electrical and electronics element
31 4 measure earth resistance by
Drawing ‐> Piping joints and fitting
Theory : 3 hrs ‐ Earth resistance
Different actions people that affect other and earth leakage circuit
5 ES
and the environment. breaker. Extra
Types, causes & effects, areas in india
that are prone to be affected,
preparedness & mitigation, dos and Test earth leakage by ELCB and
6 ES
don'ts‐before, during and after any relay. (5 Hrs)
disaster, how to reduce man‐made
disasters.
Install light fitting with reflectors
1 Laws of Illuminations. for direct and indirect lighting.
(10 Hrs)
Theory
Install light fitting with reflectors
Types of illumination system. Illumination
2 for direct and indirect lighting.
factors, intensity of light.
(10 Hrs)
Surface area and Volume of solids‐ cube, Group different wattage of
W/Shop
3 cuboids, cylinder, lamps in series for specified
calculation
sphere and hollow cylinder voltage. (5 Hrs)
Practice installation of various
lamps e.g. fluorescent tube, HP
32 Engg. Projections
4 mercury vapour, LP mercury
Drawing ‐> Concept of axes plane and quadrant
vapour, HP sodium vapour, LP
sodium vapour, metal halide etc.
Theory : 3 hrs ‐ Type of lamps,
5 ES ‐> Concept of axes plane and quadrant
Self‐Awareness, articulating personal lamps e.g. fluorescent tube, HP
6 ES values, value‐based decision making, mercury vapour, LP mercury
dilemma situations. vapour, HP sodium vapour, LP
Type of lamps, advantages/ disadvantages
Theory
Type of lamps, advantages/ disadvantages
Finding lateral surface area , total surface
33 W/Shop area and capacity in Prepare decorative lamp circuit
3
calculation liters of hexagonal, conical and cylindrical using drum switches. (5 Hrs)
shaped vessels
Prepare decorative lamp circuit
Engg. Projections
4 to produce rotating light
Drawing ‐> Concept of axes plane and quadrant
effect/running light effect.
Theory : 3 hrs ‐ Calculations of
Identify sources and types of stress
5 ES lumens and efficiency.
(positive/negative stress)
Install light fitting for show case
6 ES Managing stress (long term/ short‐term)
lighting.
Classification of electrical instruments and Practice on various analog and
1 essential forces required in indicating digital measuring Instruments. (5
instruments. Hrs)
Practice on measuring
Theory
instruments in single and three
phase circuits e.g. multi‐meter,
2 PMMC and Moving iron instruments.
Wattmeter, Energy meter, Phase
sequence meter and Frequency
meter etc.
W/Shop phase circuits e.g. multi‐meter,
3 Monthly Test WCS
calculation Wattmeter, Energy meter, Phase
34 sequence meter and Frequency
meter etc.
Engg. phase circuits e.g. multi‐meter,
4 Monthly Test ED
Drawing Wattmeter, Energy meter, Phase
sequence meter and Frequency
meter etc.
Handling rejection and building resilience,
6 ES Monthly Test Practical
identify day wasters.
Measurement of various electrical Measure power in three phase
1 parameters using different analog and circuit using two wattmeter
digital instruments. methods.
Theory Measure power factor in three
Measurement of various electrical phase circuit by using power
2 parameters using different analog and factor meter and verify the same
digital instruments. with voltmeter, ammeter and
wattmeter readings.
Measure power factor in three
Simple machines, Effort and load, phase circuit by using power
W/Shop
3 mechanical advantage, factor meter and verify the same
calculation
35 velocity ratio, efficiency of machine with voltmeter, ammeter and
wattmeter readings.
Measure electrical parameters
Engg.
4 Orthographic projections using tong tester in three phase
Drawing
circuits.
Labour Welfare legislation:‐Benefits
Theory : 3 hrs ‐ Measurement of
guaranteed under various acts‐ Factrories
5 ES energy in three phase circuit.
act, apprenticeship act, employees state
insurance act(ESI), payment wages act.
Employees provident fund act, the
Measure electrical parameters
workmen's sompensation act, POSH.
6 ES using tong tester in three phase
Interpret applicable labour and industrial
circuits.
laws.
Practice for range extension and
1 Errors and corrections in measurement. calibration of various measuring
instruments. (10 Hrs)
Theory
Practice for range extension and
Loading effect of voltmeter and voltage
2 calibration of various measuring
drop effect of ammeter in circuits.
instruments. (10 Hrs)
Determine errors in resistance
W/Shop relation between
3 measurement by voltage drop
calculation efficiency
36 method.
Determine errors in resistance
Engg.
4 Orthographic projections measurement by voltage drop
Drawing
method.
Theory : 3 hrs ‐ Extension of
Quality management:‐Create awareness range and calibration of
5 ES
on introduction of quality concepts. measuring instruments.
Concept of Quality Management(QMS), Test single phase energy meter
6 ES
PDCA, Fishbone,5s,5d, kaizen. for its errors.
Dismantle and assemble
Working principles and circuits of electrical parts of various
1 common domestic equipment and electrical appliances e.g. cooking
appliances. range, geyser, washing machine
and pump set. (25 Hrs)
Theory
Working principles and circuits of electrical parts of various
2 common domestic equipment and electrical appliances e.g. cooking
appliances. range, geyser, washing machine
electrical parts of various
W/Shop
3 velocity ratio and mechanical advantage electrical appliances e.g. cooking
calculation
range, geyser, washing machine
37
Engg. Method of first angle and third angle
4 electrical appliances e.g. cooking
Drawing projections (definition and difference)
Theory : 3 hrs ‐ Working
principles and circuits of
5 ES Indtroducton of ISO common domestic equipment
and appliances.
Preparation to the worid of work:‐Identify
6 ES electrical appliances e.g. cooking
the difference between job and carrer
Working principles and circuits of
Service and repair of bell/
1 common domestic equipment and
buzzer. (5 Hrs)
appliances.
Theory
Working principles and circuits of Service and repair of electric
2 common domestic equipment and iron, electric kettle, cooking
appliances. range and geyser.
Service and repair of electric
W/Shop
3 Lever and its types iron, electric kettle, cooking
calculation
range and geyser.
38 Engg. Method of first angle and third angle Service and repair of induction
4
Drawing projections (definition and difference) heater and oven. (10 Hrs)
Theory : 3 hrs ‐Working
principles and circuits of
5 ES Job roles available in respective trades common domestic equipment
and appliances.
Awareness of industries, and the Service and repair of induction
6 ES
respective professional pathways. heater and oven. (10 Hrs)
Working principles and circuits of
Service and repair of mixer and
1 common domestic equipment and
grinder. (10 Hrs)
appliances.
Theory
Service and repair of mixer and
2 Concept of Neutral and Earth.
grinder. (10 Hrs)
W/Shop Service and repair of washing
3 Quarterly Test WCS
calculation machine.
39
Engg. Service and repair of washing
4 Quarterly Test ED
Drawing machine.
Awareness of higher
education/educaiton/up skilling (short‐
6 ES Quarterly Test Practical
term) options Steps involved in online
application for instructor course,
Verify terminals, identify
Working principle, construction and components and calculate
1
classification of transformer. transformation ratio of single
phase transformers.
Theory
Verify terminals, identify
Single phase and three phase components and calculate
2
transformers. transformation ratio of single
phase transformers.
Perform OC and SC test to
W/Shop Measurement of Angle, Trigonometrical
3 determine and efficiency of
calculation Ratios
40 single phase transformer.
Engg. Symbol of 1st angle and 3rd angle
Drawing projection in 3rd angle.
single phase transformer.
apprenticeship and different jobs in Theory : 3 hrs ‐ Turn ratio and
popular site like the indiagobs.com, e.m.f. equation.
5 ES
naukari.com, monsterindian.com, Parents instructor meeting: 2
GOVT.website. hrs
6 ES forms of greeting determine and efficiency of
Series and parallel operation of
transformer.
Theory
2 Voltage Regulation and efficiency. determine and efficiency of
Perform series and parallel
W/Shop
3 operation of two single phase
calculation Trigonometric Table
transformers.
41 Perform series and parallel
Engg. Orthographic projection from isometric
4 operation of two single phase
Drawing projection
transformers.
Theory : 3 hrs ‐ Auto
Transformer and instrument
5 ES Use of positive body language
transformers (CT & PT).
Verify the terminals and
Handling grievances (Use of ask‐listen‐
6 ES accessories of three phase
repeat technique)
transformer HT and LT side.
Perform 3 phase operation (i)
Method of connecting three single phase delta‐delta (ii) delta‐star (iii) star‐
1
transformers for three phase operation. star (iv) star‐delta by use of three
Theory single phase transformers.
protective devices, bushings and
Perform testing of transformer
2 termination etc. Testing of transformer
oil.
oil.
W/Shop Trigonometry‐Application in calculating Practice on winding of small

3
42 calculation height and distance transformer.
Engg. Orthographic projection from isometric Practice on winding of small

4
Drawing projection transformer.
Relationship building with customers, Types of Cooling,
5 ES
importance of probing. Extra curricular activity : 2 hrs
Use of open‐ended/close‐ended Practice of general maintenance
6 ES
questions to guage reuirement. of transformer.
Materials used for winding and winding Practice on winding of small
1
wires in small transformer. transformer.
Theory
Materials used for winding and winding Practice on winding of small
2
wires in small transformer. transformer.
W/Shop Practice on winding of small
3 Quarterly Test WCS
43 calculation transformer.
Engg. Practice on winding of small
4 Quarterly Test ED
Drawing transformer.
6 ES Revision Quarterly Test Practical
1 Revision Project Work
Theory
2 Revision Project Work
W/Shop
3 Trigonometry‐(Simple Applications) Project Work
calculation
44 Engg.
4 Reading of fabrication drawing Project Work
Drawing
Theory : 3 hrs ‐ .Revision
5 ES Revision Parents instructor meeting: 2
hrs
6 ES Revision Project Work
SYLLABUS BREAKUP OF ELECTRICIAN : SECOND YEAR
INSTRUCTOR: TULSA RAM CHOUDHARY
WEEK LESSON EX.N SKILL
TOPICS PRACTICAL SKILL HOURS
NO. NO O. NO
DC Generator - principle - parts - types - function - Identify terminals, parts and connections of Use of dc generator
1 1 1
e.m.f. equation Building up of a DC shunt generator different types of DC machines
1 20
Test a DC machine for continuity and insulation Measure field and armature resistance of DC
2 2
resistance Characteristics of DC generator machines
DC motor - principle and types Determine build up voltage of DC shunt
3 3 generator with varying field excitation and
2 performance analysis on load 20
The relation between applied voltage, back emf, Test for continuity and insulation resistance Use of magger and doing test
4 armature voltage drop, speed and flux of DC motor - 4 2 insulation resistance
of DC machine
method
DC motorofstarters
changing direction
Relation of rotation
between torque, flux and
5 armature current in a DC motor Service and 5 Start, run and reverse direction of rotation of
maintenance of DC motor starters DC series, shunt and compound motors
3 Characteristics and applications of a DC series motor Perform no load and load test and determine Load and no load test generator 22
Characteristic and applications of a DC shunt motor characteristics of series and shunt generators.
6 DC compound motor - load characteristics 6 3
Speed control methods of a DC motor and their Practice dismantling and assembling in DC Repair and maintenance of dc
7 applications Method of calculation of control 7 shunt motor 4 machine
resistance and new speed
4 25
Troubleshooting in DC machines Maintenance Practice dismantling and assembling in DC
8 procedure for DC machines DC motor control system 8 compound generator
(drives) AC-DC and DC-AC control
Materials used for winding - field coil winding Conduct performance analysis of DC series,
9 Winding wires 9 shunt and compound motors
5 25
Armature winding - terms - types - rewinding of Dismantle and identify parts of three point
10 mixer/liquidizer 10 and four point DC motor starters
Simplex lap and wave winding - developed diagram Assemble, Service and repair three point and
11 11
four point DC motor starters.
6 25
1
NO. NO O. NO
6 Preparation of armature for rewinding Practice maintenance of carbon brushes, 25
12 12 brush holders, Commutator and slip-rings
Rewinding of mixer/liquidizer Perform speed control of DC motors - field

13 13
7 and armature control method 25
14 Method of rewinding and balancing the armature 14 Carry out overhauling of DC machines
Testing of armature winding Perform DC machine winding by developing
8 15 15 connection diagram, test on growler and 25
assemble
Principle of induction motor Construction of a 3- Identify parts and terminals of three phase AC Testing of ac motor
phase squirrel cage induction motor - relation motors
16 between 16 5
slip, speed, rotor frequency, copper loss and torque
9 Classification of squirrel cage motors Insulation test Make an internal connection of automatic 35
17 on 3 phase induction motors 17 star-delta starter with three contactors
Starter for 3-phase induction motor - power control Connect, start and run three phase induction Ac motor connection, start, run and
18 circuits - D.O.L starter 18 motors by using DOL, stardelta and auto- 6 change of DOR
transformer starters
B.I.S. symbols pertaining to contactor and machines Connect, start, run and reverse direction of
rotation of slip-ring motor through rotor
19 19
resistance starter and determine performance
characteristic
10 23
Numerical problems in ac 3-phase induction motors Determine the efficiency of squirrel cage
Jogging (inching) control circuits for motors Rotary induction motor by brake test
20 20
type switches Manual star-delta starter
Semi-automatic star-delta starter Automatic star- Determine the efficiency of three phase
21 delta starter 21 squirrel cage induction motor by no load test
and blocked rotor test
11 22
Three-phase, slip-ring induction motor Resistance Measure slip and power factor to draw
22 starter for 3-phase, slip-ring induction motor 22 speedtorque (slip/torque) characteristics
2
NO. NO O. NO
23 Method of measurement of slip in induction motor 23 Test for continuity and insulation resistance 7 Testing of ac motor
Efficiency - characteristics
Characteristics of induction
of squirrel cage motor-
induction motornoNo-
load of three phase
Perform speed induction
control ofmotors.
three phase
12 load test of induction motor Blocked rotor test induction motors by various methods like 20
24 24
rheostatic control, autotransformer etc
Efficiency from no-load and blocked rotor test Effect Perform winding of three phase AC motor by
13 25 of external resistance in slip ring motor rotor circuit 25 developing connection diagram, test and 20
Auto-transformer starter assemble.
Single phasing preventer / phase failure relay Braking Maintain, service and troubleshoot the AC Service and troubleshoot the AC
26 system of motors Method of speed control of 3 26 motor starter 8 motor
phase induction motor
Fundamental terms used in AC winding Hand winding Identify parts and terminals of different types Testing of ac single phase motor
27 process 3 phase squirrel cage induction motor 27 of single phase AC motors 9
14 25
winding (single layer
Method of placing coils in a basket or distributed Install, connect and determine performance
winding Three-phase induction motor winding (single single phase AC motors
28 28
layer - concentric type
- half coil connection)
Start, run and reverse the direction of Connection, run and DOR change of
29 3 phase squirrel cage induction motor - double layer 29 rotation of single phase AC motors 10 ac single phase motor
15 distributed type winding Testing of windings 20
Insulating varnish and varnishing process in electric Practice on speed control of single phase AC
30 machines Method of connecting end connection, 30 motors
group connection, terminal leads,
Maintenance, service and troubleshooting in AC 3 Compare starting and running winding
31 phase squirrel cage induction motor and starters 31 currents of a capacitor run motor at various
Troubleshooting of motor starters loads and measure the speed
16 20
Single phase motors - split phase induction motor - Carry out maintenance, service and repair of
32 induction-start, induction-run motor Centrifugal 32 single phase AC motors
switch
Single phase, split phase type motor winding Practice on single/double layer and concentric Rewinding of ac motor
17 33 (concentric coil winding) Capacitor-start, induction- 33 winding for AC motors, testing and 11 25
run motor Capacitors used in single phase capacitor assembling
motors
3
NO. NO O. NO
Permanent capacitor motor - capacitor-start, Practice on single/double layer and concentric
capacitor-run motor and shaded pole motor The winding for AC motors, testing and
34 34
shaded pole motor Universal motor Troubleshooting assembling
of universal motor
18 25
Repulsion motor Stepper motor Hysteresis motor Carry out maintenance and servicing of Maintenance and servicing of single
35 35 12
Reluctance motor universal motor. phase motor.
Alternator - principle - relation between poles, speed Install an alternator, identify parts and Studay of alternator
36 36 13
and frequency terminals of alternator.
Types and construction of alternators Test for continuity and insulation resistance
37 37 of alternator.
Generation of 3-phase voltage and general test on Connect, start and run an alternator and build Build up the ac voltage.
19 38 38 14 25
alternator up the voltage.
Emf equation of the alternator Characteristic and
39 voltage regulation of the alternator 39 Determine the load performance and voltage
regulation of three phase alternator
Parallel operation and synchronisation of three phase Parallel operation and synchronization of Parallel operation of three phase
40 alternators - brushless alternato Synchroscope 40 three phase alternators. 15 alternators.
20 method Brushless alternator 25
Synchronous motor Install a synchronous motor, identify its parts Use of synchronous motor.
41 41 16
and terminals
Connect, start and plot Vcurves for
42 42 synchronous motor under different excitation
21 20
MG set and rotary converter and inverter and load conditions.
43 43 Identify parts and terminals of MG set
Maintenance of MG set Work on motor genrator set.
22 44 44 Start and load MG set with 3 phase induction 17 20
motor coupled to DC shunt generator
Circuit board soldering and resistor colour coding Determine the value of resistance by colour
45 45
23 Soldering technique code and identify
Test active typeselectronic
and passive 25
46 Semiconductor theory/active and passive 46 components and its applications
components
PN Junction-semiconductor diodes Determine V-I characteristics of
47 47
24 semiconductor diode 20
48 Rectifiers 48 Construct half wave, full wave and bridge
rectifiers using semiconductor diode
4
NO. NO O. NO
Transistor Transistor biasing and characteristics Check transistors for their functioning by
49 49
identifying its type and terminals
25 Transistor as a switch. 20
50 50 Bias the transistor and determine its
characteristics
voltage regulator and amplifiers
51 51 Use transistor as an electronic switch and
26 series voltage regulator 22
Function generator. Operate and set the required frequency using
52 52
function generator
Cathode ray oscilloscope (CRO) Printed circuit boards Make a printed circuit board for power Make a pcb board.
53 53 18
(PCB) supply.
Power electronic devices - UJT and FET Construct simple circuits containing UJT for Construct simple dc circuits.
27 54 54 19 38
triggering and FET as an amplifier
Power supplies - troubleshooting Troubleshoot defects in simple power
55 55
supplies.
Power control circuit using SCR,DIAC,TRIAC & IGBT Construct power control circuit by SCR, Diac, Control circuit by SCR
56 56 20
Triac and IGBT
28 25
Integrated circuit voltage regulators Construct variable DC stabilized power supply
57 57
using IC.
Binary numbers, logic gates and combinational Practice on various logics by use of logic gates Connection logic gates and circuits
58 58 21
circuits and circuits
Wave shapes - oscillators and multivibrators Generate and demonstrate wave shapes for Amplification and oscillator.
29 25
voltage and current of rectifier, single stage
59 59 22
amplifier and oscillator using CRO.
Control elements, accessories - layout of control Design layout of control cabinet, assemble Desige of control and power wiring
cabinet Power and control circuits for three phase control elements and wiring accessories for: Circuits of starters.
60 60 23
motors (i) Local and remote control of induction
30 motor 25
Installation of instruments and sensors in control Forward and reverse operation of induction Operation of various type staters.
61 panel and its performance testing 61 motor. 24
5
NO. NO O. NO
Automatic star-delta starter control and power wiring
whit single phase priventer.
62
Automatic star-delta starter with change of
31 62 direction of rotation. 25
63
Sequential control of three motors
Various control elements e.g. circuit breakers, relays, Carry out wiring of control cabinet as per Control pannel wiring digram
63 64 wiring diagram, bunching of XLPE cables, 25 connect to motors.
channeling, tying and checking etc
32 25
contactors and timers etc
64 65 Mount various control elements e.g. circuit
breakers, relays, contactors and timers etc
Wiring of control cabinet as per wiring diagram, Identify and install required measuring
bunching of XLPE cables, channeling, tying and 66 instruments and sensors in control panel
33 65 checking etc 25
Test the control panel for its performance
67
66 AC/DC drives 68 Perform speed control of DC motor using

Speed control of 3 phase induction motor by VVVF/AC thyristors / DC drive.
Perform speed control and reversing the Speed control and direction of
34 67 drive 69 direction of rotation of AC motors by using 26 rotation of AC motors by using 50
thyristors / AC drive thyristors / AC drive
Construct and test a universal motor speed
68 Speed controller using SCR. 70 controller using SCR.
Voltage stabilizer and UPS Assemble circuits of voltage stabilizer and
69 71 UPS
35 25
70 Emergency light 72 Prepare an emergency light
Assemble circuits of battery charger and
73
inverter
36 71 Troubleshoot battery charger and inverter 30
Test, analyze defects and repair voltage
74
stabilizer, emergency light and UPS
Battery charger and inverter Maintain, service and troubleshoot battery
72 75
charger and inverter
37 20
6
NO. NO O. NO
37 Stabiliser, battery charger, emergency light, inverter Install an Inverter with battery 20
73 and UPS Installation of inverter in domestic wiring 76 Install an Inverter with battery and connect it 27
in domestic wiring for operation.
Sources of energy - Thermal power generation
74 77 Draw layout of thermal power plant and
identify function of different layout elements
Hydel power plants
75 78 Draw layout of hydel power plant and identify
functions of different layout elements.
38 20
Visiting of electrical substation Draw actual circuit diagram of substation Desige of substation
76 79 28
Electrical substations visited and indicate various components
Electrical power generation by non conventional Prepare layout plan and Identify different
methods Tidal power generation Magneto hydro elements of solar power system.
77 80
dynamic (MHD) power generation
Prepare layout plan and Identify different Prepare of wind power systems.
81 29
Power generation by solar and wind energy Wind elements of wind power system
78
power generation Assemble and connect solar panel for Prepare of solor power systems.
82 30
39 illumination 25
Electrical supply system - transmission - line Practice installation of insulators used in Work on over head line installation.
79 insulators 83 HT/LT line for a given voltage range 31
Overhead lines /poles erection-fastening of insulator Draw single line diagram of transmission and Power and distribution
80 84 32
Joining of aluminium conductors distribution system. transfarmers connections.
Domestic service line - IE rules Measure current carrying capacity of Current capicity of conductor given
40 81 85 33 20
conductor for given power supply power supply.
Bus-bar system - power tariff terms and definitions Fasten jumper in pin, shackle and suspension Fixing of over head line accessories.
82 86 34
type insulators
Erect an overhead service line pole for single
Line protective relays - types - operation phase 230 V distribution system in open
83 87
space.
Circuit breakers - parts - functions- tripping Practice on laying of domestic
41 88 25
mechanism service line
84
Install bus bar and bus coupler on LT line. Install of bus bar
89 35
7
NO. NO O. NO
Identify various parts of relay and ascertain
90
the operation
Practice setting of pick up current and time Operation of various realy
91 setting multiplier for relay operation. 36
Identify the parts of circuit breaker, check its Operation of circuit breaker.
42 85 Repair and maintenance of CBs 92 operation. 37 25
93 Test tripping characteristic of circuit breaker

for over current and short circuit current
Practice on repair and maintenance of circuit Repair and maintenance of circuit
94 38
breaker breaker.
GOVT ITI BEAWAR

GANESHPURA ROAD BEAWAR
8
NO. NO O. NO

Trade Electrician: Syllabus Breakup Daily

Uploaded by

Copyright:

Available Formats

Trade Electrician: Syllabus Breakup Daily

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Trade Electrician: Syllabus Breakup Daily

Uploaded by

Copyright:

Available Formats

Trade

W/Shop Mass, volume, density, weight & specific Practice in Soldering of joints /

W/Shop Trigonometry‐Application in calculating Practice on winding of small

Engg. Orthographic projection from isometric Practice on winding of small

Rewinding of mixer/liquidizer Perform speed control of DC motors - field

66 AC/DC drives 68 Perform speed control of DC motor using

93 Test tripping characteristic of circuit breaker

GOVT ITI BEAWAR

You might also like