Scribd Logo
Upload

Welcome to Scribd!

  • 119 views

    Industrial Automation Engineers Interview Questions

    Uploaded by

    Jêmš Navik
    Automation involves using technical equipment to delegate human control functions for increased productivity, quality and safety. The main components used in automation are sensors, transmitters, control systems like PLCs and DCS, and output devices. Common control systems include PID, PLC-based, and DCS-based systems. PLCs can be programmed whereas relays cannot, and DCS systems are more complex than PLCs with distributed functionality. Transmitters convert sensor signals to electrical signals that can be transmitted over long distances. Common sensors include RTDs, thermocouples, pressure sensors and flow sensors.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Industrial Automation Engineers Interview Questions

    Uploaded by

    Jêmš Navik
    119 views5 pages
    Automation involves using technical equipment to delegate human control functions for increased productivity, quality and safety. The main components used in automation are sensors, transmitters, control systems like PLCs and DCS, and output devices. Common control systems include PID, PLC-based, and DCS-based systems. PLCs can be programmed whereas relays cannot, and DCS systems are more complex than PLCs with distributed functionality. Transmitters convert sensor signals to electrical signals that can be transmitted over long distances. Common sensors include RTDs, thermocouples, pressure sensors and flow sensors.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Automation involves using technical equipment to delegate human control functions for increased productivity, quality and safety. The main components used in automation are sensors, transmitters, control systems like PLCs and DCS, and output devices. Common control systems include PID, PLC-based, and DCS-based systems. PLCs can be programmed whereas relays cannot, and DCS systems are more complex than PLCs with distributed functionality. Transmitters convert sensor signals to electrical signals that can be transmitted over long distances. Common sensors include RTDs, thermocouples, pressure sensors and flow sensors.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    119 views5 pages

    Industrial Automation Engineers Interview Questions

    Uploaded by

    Jêmš Navik
    Automation involves using technical equipment to delegate human control functions for increased productivity, quality and safety. The main components used in automation are sensors, transmitters, control systems like PLCs and DCS, and output devices. Common control systems include PID, PLC-based, and DCS-based systems. PLCs can be programmed whereas relays cannot, and DCS systems are more complex than PLCs with distributed functionality. Transmitters convert sensor signals to electrical signals that can be transmitted over long distances. Common sensors include RTDs, thermocouples, pressure sensors and flow sensors.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 5

    Industrial Automation Engineers Interview Questions

    1. What is Automation?
    Automation is delegation of human control functions to technical equipment for increasing productivity,
    better quality, reduced cost & increased in safety working conditions.
    2. What are the different components used in automation?
     Sensors for sensing the input parameters (RTD, Thermocouple, Pressure, Flow, Level; etc)
     Transmitters for transmitting the raw signal in electrical form
     Control system which includes PLC, DCS & PID controllers
     Output devices / actuators like drives, control valves.
    3. What are the different control systems used in Automation?
     PID Controller based control system
     PLC based control system
     DCS based Control system
     PC Based automation system
    4. Explain PID based control system.
    PID (Proportional Integral Derivative) is the algorithm widely used in closed loop control.

    The PID controller takes care of closed loop control in plant. A number of PID controller with single or
    multiple loop can be taken on network.

    PID Controllers are widely for independent loops. Although some logic can be implemented but not much of
    sequential logic can be implemented in PIDs.

    5. Difference between PLC & Relay ?


     PLC can be programmed whereas a relay cannot.
     PLC works for analog I/Os such as PID loops etc. whereas a relay cannot
     PLC is much more advanced as compared to relay.
     Modifications in relay base circuit is difficult compared to PLCs

    6. Difference between PLC and DCS ?


    DCS:

    The system uses multiple processors, has a central database and the functionality is distributed. That is the
    controller sub system performs the control functions, the history node connects the data, the IMS node gives
    reports, the operator station gives a good HMI, the engineering station allows engineering changes to be
    made.

    PLC:

    The system has processor & I/O’s and some functional units like basic modules, communication modules and
    so on. Uses a SCADA for visualization. Generally the SCADA does not use a central database.
    DCS is often used in the big plants where the redundancy level needed is more and the analog input used are
    high.

    7. What is PC based control system ?


    In PC based control system, the CPU of computer acts as processor, the PCI based cards are used for
    connecting Input and Output. The RAM acts as memory. Hard disk is used as storage device.

    Currently this systems are very useful when the large data is to be proceed with very high speed. In many
    cases for greater accuracy we can use the real-time operating system.
    8. What is Encoder ?
    A feedback device which converts mechanical motion into electronic signals. Usually an encoder is a rotary
    device that outputs digital pulses which correspond to incremental angular motion.

    The encoder consists of a glass or metal wheel with alternating clear and opaque stripes that are detected by
    optical sensors to produce the digital outputs

    9. Which are the leading PLC providers ?


    The leading PLC providers include
     Rockwell Automation : Allen Bradley (Micrologix, SLC, PLC, Control Logix)
     Siemens ( S7 200, S7 300 , S7 400)
     Grouppe Schneider : Modicon ( Nano, Micro, Premium, Quantum)
     GE Fanuc : Versa, Series 90-30, 90-70
     Messung : Nextgen

    10. Which are the leading DCS providers ?


    The leading DCS providers include

     Yokogawa : Centum VP, CS 3000 , CS 5000 (Earlier Centum Excel, Micro Excel)
     Honeywell : TDC 3000
     Fisher – Rosemant – Delta V
     ABB – Freelance 2000
     Moore – APACS
     Fox boro – I/A series

    11. Which are the leading SCADA software providers ?


    The leading SCADA software / MMI providers include
     Wonderware : InTouch
     Intellution iFix (Earlier FixDMACS)
     Siemens : WinCC
     Allen Bradley : RS View ( Earlier Control View)
     KPIT : Astra

    12. What types of sensors are used for measuring different parameters?
     Temperature sensors – RTD, Thermocouple, Thermister
     Pressure Sensor – Borden Tube, Bellows, Strain gauge
     Flow sensor – Pitot tube, Orifice, Ultrasonic+
     Level, Conductivity, Density, Ph

    13. What is transmitter?


    A transmitter is an electronic device that is generally mounted in the field in close proximity to a sensor. The
    sensor (also known as a transducer) measures a physical variable such as temperature or pressure and
    outputs a very low level electronic signal.

    The basic function of the transmitter is to provide the correct electrical power to turn on (or excite) the
    sensor then to read the low level sensor signal, amplify it to a higher level electrical signal and send that
    signal a long distance to a control or read-out device.
    Since low-level electrical signals do not transmit long distances with great accuracy, installing a transmitter
    generally gives a tremendous improvement in the accuracy of the information delivered to a larger control
    system. Typically the output form the transmitter is 4-20 mA or 0-10 V
    14. Why 4-20 mA preferred over 0-10 V signal ?
    The 0-10 V signal has tendency to drop because of line resistance. If the distance between sensor and input
    card is more the signal will not properly represent the field value.

    The 4-20 mA will travel a long distance without dropping signal value.

    15. Why 4-20 mA preferred over 0-20 mA signal ?


    With 0- 20 mA you can not distinguish between minimum field value and connection break. With 4-20 mA,
    internal circuit can distinguish between connection break of minimum value.

    Normally when the value is minimum the transmitter will give you 4 mA while in case of connection
    breakage it will give 0 mA.

    16. Difference between 2 wire, 3 wire and 4 wire transmitter.


    In 2 wire transmitter the power and signal are transmitted through same cable.
    In 3 wire transmitter the data signal and power are with respect to common ground.
    In 4 wire transmitter two wires for power supply and two for signals. Only current transmitters can be used
    as 2 wire transmitters.

    17. What is a “Smart” Transmitter ?


    A “Smart” transmitter is a transmitter that uses a microprocessor as the heart of the electronics.

    In addition, a “Smart” transmitter will output some type of remote digital communications allowing you to
    read and set-up the device from a remote position.

    18. What is Field bus ?


    Fieldbus is a general term for a digital only, high speed communications protocol. The key attribute to
    Fieldbus communications is higher speed communications with the possibility of addressing multiple
    transmitters all on the same field wiring.

    The Foundation Fieldbus is a specific digital protocol that is often shortened to just be called Fieldbus. Other
    digital only communications such as Profibus are also Fieldbus protocols

    19. What is Actuator ?


    In a closed-loop control system, the part of the final control element that translates the control signal into
    action by the control device.
    An actuator is a component of a machine that is responsible for moving or controlling a mechanism or
    system.
    An actuator requires a control signal and a source of energy. The control signal is relatively low energy and
    may be electric voltage or current, pneumatic or hydraulic pressure, or even human power.

    20. Explain Working of RTDs


    Resistance Temperature Device works on the principles that the resistance of the material changes as its
    temperature changes.

    Temperature is determined by measuring resistance and then using the RTD Resistance vs Temp
    characteristic to detect temperature.

    Typical elements used for RTD are Nickel, Copper and Platinum. Platinum is widely used in RTDs because of
    accuracy.

    PT 100 means at 0 deg temp 100 ohms resistance. A typical RTD consists of a fine platinum wire wrapped
    around a mandrel and covered with a protective coating (glass or ceramic).
    21. Temperature measurement range supported by RTDs?
    The RTD work on temperature range between–250 to 850 deg C.

    22. Explain Working of Thermocouple


    Thermocouple consists of two strips or wires made up of different metals and joined at one end. The
    temperature at that juncture induces an electromotive force (emf) between the other ends.

    As the temperature goes up the emf also increases. Through standard charts and tables the corresponding
    temperature can be found out.

    The relationship between the thermocouple output and the temperature is quite non linear.
    Different metallurgies produce different outputs. The different metallurgies and different lineararities result
    in different thermocouple designations such as “J”, “K,”, “N”, “L”, etc.

    23. What is Cold Junction compensation?


    The industry accepted standard for the temperature at open end is 0 deg C.

    Therefore most tables and chart make the assumption that the temp at open end is 0 deg C. In industry the
    open ends are always at actual room temperature and not 0 deg C.

    The emf adjustment because of difference between the actual temp and 0 deg C is referred as Cold Junction
    Correction (CJ Correction)

    24. Temperature measurement range supported by thermocouple ?


    The thermocouple work on broad temperature range ie –270 to 2300.

    25. Can we split one T/C signal to two separate instruments?


    No. The T/C signal is a very low-level millivolt signal, and should only be connected to one device.

    Splitting to two devices may result in bad readings or loss of signal.

    The solution is to use a “dual” T/C probe, or convert one T/C output to a 4-20 mA signal by using a
    transmitter or signal conditioner; then the new signal can be sent to more than one instrument

    26. What are the flow measuring instruments used in Flow measurement ?
     Differential pressure meters
     Positive displacement
     Velocity meters

    27. Explain working of differential pressure measurement ?


    Suitable restriction placed in flow stream causes a differential pressure across it.
    As flow depends upon differential pressure (Head) & area, so any of them or both can be varied for varying
    flow.

    28. What are the components of differential flow sensor ?


    For creating differential pressure : Orifice plate, Venturi Tube, Flow Nozzle , pitot tube
    For measuring pressure : U-Tube Manometers, Ring–Balance Manometer, D.P. Cell

    29. What type of pressure sensors used in pressure measurement?


     Manometers
     Bourdon tubes
     Bellow elements
     Diaphragm elements
     DP transmitters

    30. Explain working of differential pressure transmitters.


    Process pressure is transmitted through isolating diaphragms and oil fill fluid to a sensing diaphragm. The
    sensing diaphragm is a stretched spring element that deflects in response to differential pressure across it.

    The displacement of the sensing diaphragm, a maximum deflection of0.004 inch (0.10 mm), is proportional
    to the applied pressure.

    Capacitor plates on both sides of the sensing diaphragm detect the position of the diaphragm.
    The transmitter electronics convert the differential capacitance between the sensing diaphragm and the
    capacitor plates into a two- wire, 4-20 mA dc signal and a digital output signal.

    31. What is Control Valves ?


    The control valve, commonly named the final control element of control contains a pneumatic device that
    converts the control signal from the controller in action, regulating the flow.

    A control valve is a valve used to control fluid flow by varying the size of the flow passage as directed by a
    signal from a controller.
    This enables the direct control of flow rate and the consequential control of process quantities such as
    pressure, temperature, and liquid level.

    32. What type of control valves used in the industry ?


     ON – OFF SERVICES :- Gate, Ball, Diaphragm, Plug, Butterfly valves.
     THROTTLING SERVICES :- Globe, Butterfly, Diaphragm, Pinch valves.
     NON – REVERSE FLOW :- Check valves.

    33. What are the specifications of the control valve ?


    Following specifications are used for control valve

     Flow medium and operating temperature


     Flow rate kg/hr or Nm3/hr Max/Min/Normal
     Inlet and Outlet pressure : kg/cm2 Max/Min/Normal
     Max. allowable diff. Pressure : kg/cm2
     Density of medium : kg/m3
     Viscosity
     Cv : Valve Flow Coefficient

    34. What are the components of control valve ?


     Actuator, Body, Trim, Diaphragm, Diaphragm plate, Actuator stem
     Actuator spring, Seat, Travel Indicator, Valve stem, Gaskets, Yoke, Hand wheel

    35. What is flow coefficient ?


    It is the flow of water (G=1, T= 6 to 34 deg. C) through the valve at full lift in U.S gallon per minute with a
    pressure drop across the valve of 1 psi.

    If you liked this article, then please subscribe to our YouTube Channel for PLC and SCADA video tutorials.

    You might also like