Practical: 01 Aim: To Study Various Networking Components. Major Computer Network Components

PRACTICAL: 01
AIM: To study various Networking Components.
Major computer network components

Computer network requires the following devices (some of them are optional):-
• Network Interface Card (NIC)
• Hub
• Switches
• Cables and connectors
• Router
• Modem
Repeater
1. Network Interface Card
Network adapter is a device that enables a computer to talk with other computer/network. Using
unique hardware addresses (MAC address) encoded on the card chip, the data-link protocol
employs these addresses to discover other systems on the network so that it can transfer data to
the right destination.
1
There are two types of network cards: wired and wireless. The wired NIC uses cables and
connectors as a medium to transfer data, whereas in the wireless card, the connection is made
using antenna that employs radio wave technology. All modern laptop computers incorporated
wireless NIC in addition to the wired adapter.
Network Card Speed
Network Interface card, one of the main computer network components, comes with different
speeds, 10Mbps, 100Mbps, and 1000Mbps, so on. Recent standard network cards built with
Gigabit (1000Mbps) connection speed. It also supports to connect slower speeds such as
10Mbps and 100Mbps. However, the speed of the card depends on your LAN speed.
For example, if you have a switch that supports up to 100Mbps, your NIC will also transfer a
data with this same speed even though your computer NIC has still the capability to transfer
data at 1000Mbps (1Gbps). In modern computers, network adapter is integrated with a
computer motherboard. However if you want advanced and fast Ethernet card, you may buy and
install on your computer using the PCI slot found on the motherboard (desktop)
and ExpressCard slots on laptop .
2. Hub
Hub is a device that splits a network connection into multiple computers. It is like a distribution
center. When a computer request information from a network or a specific computer, it sends
the request to the hub through a cable. The hub will receive the request and transmit it to the
entire network. Each computer in the network should then figure out whether the broadcast data
is for them or not.
2
Currently Hubs are becoming obsolete and replaced by more advanced communication devices
such as Switches and Routers.
3. Switch
Switch is a telecommunication device grouped as one of computer network components. Switch

is like a Hub but built in with advanced features. It uses physical device addresses in each
incoming messages so that it can deliver the message to the right destination or port.
Like Hub, switch don’t broadcast the received message to entire network, rather before sending
it checks to which system or port should the message be sent. In other words switch connects
the source and destination directly which increases the speed of the network. Both switch and
hub have common features: Multiple RJ-45 ports, power supply and connection lights.
4. Cables and connectors
Cable is one way of transmission media which can transmit communication signals. The wired
network typology uses special type of cable to connect computers on a network.
3
There are a number of solid transmission Media types, which are listed below. - Twisted pair
wire
It is classified as Category 1, 2, 3, 4, 5, 5E, 6 and 7. Category 5E, 6 and 7 are high-speed cables
that can transmit 1Gbps or more. -
Coaxial cable
Coaxial cable more resembles like TV installation cable. It is more expensive than twisted-pair
cable but provide high data transmission speed.
Fiber-optic cable
It is a high-speed cable which transmits data using light beams through a glass bound fibers.
Fiber-optic cable is high data transmission cable comparing to the other cable types. But the
cost of fiber optics is very expensive which can only be purchased and installed on
governmental level.
5. Router
When we talk about computer network components, the other device that used to connect a
LAN with an internet connection is called Router. When you have two distinct
networks (LANs) or want to share a single internet connection to multiple computers, we use a
Router.
4
In most cases, recent routers also include a switch which in other words can be used as a switch.
You don’t need to buy both switch and router, particularly if you are installing small business
and home networks.
There are two types of Router: wired and wireless. The choice depends on your physical
office/home setting, speed and cost.
6. Modems
A modem enables you to connect your computer to the available internet connection over the
existing telephone line. Like NIC, Modem is not integrated with a computer motherboard. It
comes as separate part which can be installed on the PCI slots found on motherboard.
A modem is not necessary for LAN, but required for internet connection such as dial-up and
DSL.
There are some types of modems, which differs in speed and transmission rate. Standard PC
modem or Dial-up modems (56Kb data transmission speed), Cellular modem (used in a laptop
5
that enables to connect while on the go), cable modem (500 times faster than standard
modem) and DSL Modems are the most popular.
7. Repeater
A repeater operates at the physical layer. Its job is to regenerate the signal over the same
network before the signal becomes too weak or corrupted so as to extend the length to which the
signal can be transmitted over the same network. An important point to be noted about repeaters
is that they do not amplify the signal. When the signal becomes weak, they copy the signal bit
by bit and regenerate it at the original strength. It is a 2 port device.
8. Bridge
A bridge operates at data link layer. A bridge is a repeater, with add on the functionality of filtering
content by reading the MAC addresses of source and destination. It is also used for interconnecting
two LANs working on the same protocol. It has a single input and single output port, thus making it a
2 port device.
Types of Bridges
Transparent Bridges:-
These are the bridge in which the stations are completely unaware of the
bridge’s existence i.e. whether or not a bridge is added or deleted from the network, reconfiguration of
the stations is unnecessary. These bridges make use of two processes i.e. bridge forwarding and bridge
learning.
Source Routing Bridges:-

In these bridges, routing operation is performed by source station and the frame specifies which route
to follow. The hot can discover frame by sending a special frame called discovery frame, which
spreads through the entire network using all possible paths to destination.
6
9. Gateway
A gateway, as the name suggests, is a passage to connect two networks together that may work upon
different networking models. They basically work as the messenger agents that take data from one
system, interpret it, and transfer it to another system. Gateways are also called protocol converters and
can operate at any network layer. Gateways are generally more complex than switch or router.
7
General Network Diagram
List of Networking Devices with their respective layer
8
9

Practical: 01 Aim: To Study Various Networking Components. Major Computer Network Components

Uploaded by

Copyright:

Available Formats

Practical: 01 Aim: To Study Various Networking Components. Major Computer Network Components

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Practical: 01 Aim: To Study Various Networking Components. Major Computer Network Components

Uploaded by

Copyright:

Available Formats

PRACTICAL: 01

AIM: To study various Networking Components.

Major computer network components

• Network Interface Card (NIC)

• Cables and connectors

1. Network Interface Card

Network Card Speed

Switch is a telecommunication device grouped as one of computer network components. Switch

4. Cables and connectors

Source Routing Bridges:-

List of Networking Devices with their respective layer

You might also like