4.IS 10262 2019 New Mix Design

(Reaffirmed 0) Hkkjrh; ekud IS 10262 : 2019
Indian Standard
oaQØhV feJ vuqikru —

ekxZn'khZ fl¼kar
( nwljk iqujh{k.k )
Concrete Mix Proportioning —

Guidelines
( Second Revision )
ICS 91.100.30
© BIS 2019
Hkkjrh; ekud C;wjks

BUREAU OF INDIAN STANDARDS
ekud Hkou] 9 cgknqj'kkg ”kiQj ekxZ] ubZ fnYyh&110002
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI-110002
www.bis.org.in www.standardsbis.in
January 2019 Price Group 12

Cement and Concrete Sectional Committee, CED 02
FOREWORD
This Indian Standard (Second Revision) was adopted by the Bureau of Indian Standards, after the draft
finalized by the Cement and Concrete Sectional Committee had been approved by the Civil Engineering
Division Council.
This standard provides guidelines for proportioning concrete mixes as per the requirements using the concrete
making materials including other supplementary materials identified for this purpose.
This standard was first published in 1982 and subsequently revised in 2009. In the first revision, the title of the
standard was modified as ‘Concrete mix proportioning — Guidelines’ from ‘Recommended guidelines for
concrete mix design’. The major changes in the first revision had been, restricting the applicability of the
standard to ordinary and standard grades of concrete, aligning the standard to IS 456 : 2000 ‘Plain and
reinforced concrete — Code of practice (fourth revision)’; review and modification of the requirements for
selection of water cement ratio, water content and estimation of coarse aggregate content and fine aggregate
content; inclusion of an additional illustrative example of concrete mix design, etc.
In this second revision, the following major modifications have been made:
a) The standard has been divided into five sections, as follows:
1) Section 1 General
2) Section 2 Ordinary and standard grades of concrete
3) Section 3 High strength grades of concrete
4) Section 4 Self compacting concrete
5) Section 5 Mass concrete
b) Mix proportioning procedure for high strength concrete for M 65 or above (up to target strength of
M 100) has been included.
c) The initial data to be provided for mix proportioning has been made more encompassing, covering the
provisions of revised IS 383 : 2016 ‘Coarse and fine aggregates for concrete (third revision)’, use of
admixtures, etc.
d) The target mean strength for mix proportioning formula has been refined to include a new factor based
on the grade of concrete. This has been done to ensure a minimum margin between the characteristic
compressive strength and the target mean compressive strength.
e) The calculations for standard deviation have been detailed.
f) A graph of water-cement ratio versus 28 days strength of concrete has been introduced for different
grades and types of cement, as an alternate method for assuming the initial water-cement ratio.
g) Illustrative annexes for concrete mix proportioning for PPC, OPC with fly ash, OPC with ggbs, high
strength concrete, self compacting concrete and mass concrete have been provided.
h) Guidelines on using/selecting water reducing admixtures have been introduced as an informatory annex
(see Annex G).
j) The consideration of air content in design of normal (non-air entrained) concrete mix proportion, has
been reintroduced.
This standard requires compliance to the provisions of IS 456:2000 particularly to ensure that minimum
stipulations for durability are met with, such as minimum OPC content, maximum free water-content ratio and
minimum grade of concrete. However, in certain projects, some deviations in the concrete mix proportioning
may be required; all such deviations are to meet certain stricter criteria than those given in IS 456:2000.
Concrete has become an indispensable construction material. In the present scenario, concrete has bypassed the
stage of mere four component system, that is, cement, water, coarse aggregate and fine aggregate. It can be a
combination of far more number of ingredients, for example, a judicious combination of ingredients from as
many
(Continued on third cover)

IS 10262 : 2019
Indian Standard
CONCRETE MIX PROPORTIONING — GUIDELINES
( Second Revision )
1
SECTION 1 GENERAL
IS 10262 : 2019 IS No. Title
ash: Part 1 For use as pozzolana
1 SCOPE
in cement, cement mortar and
1.1 This standard provides the guidelines for concrete (third revision)
proportioning concrete mixes as per the requirements 9103 : 1999 Specification for admixtures for
using the concrete making materials including other concrete (first revision)
supplementary materials identified for this purpose. 15388 : 2003 Specification for silica fume
The proportioning is carried out to achieve 16714 : 2018 Ground granulated blast furnace
specified characteristics at specified age, workability slag for use in cement, mortar
of fresh concrete and durability requirements. and concrete — Specification
1.2 This standard is applicable for ordinary, standard 3 TERMINOLOGY
and high strength concrete grades. The standard also For the purpose of this standard, the following
covers provisions for the mix proportioning of self definitions shall apply.
compacting concrete and mass concrete.
3.1 Water-Cement Ratio (w/c) — The ratio is
1.3 All requirements of IS 456 in so far as they calculated by dividing the mass of the mixing water
apply, shall be deemed to form part of this standard. by the mass of the cement. It refers to the ratio
corresponding to the saturated surface dry condition
2 REFERENCES
of aggregates.
The following standards contain provisions, which
3.2 Water-Cementitious Materials Ratio (w/cm)
through reference in this text, constitute provisions of
— The ratio (w/cm) is calculated by dividing the
this standard. At the time of publication, the editions
mass of the mixing water by the combined mass of
indicated were valid. All standards are subject to
the cement and fly ash or other cementitious
revision and parties to agreements based on this
materials or a combination thereof . It refers to
standard are encouraged to investigate the possibility
the ratio corresponding to the saturated surface dry
of applying the most recent editions of the standards
condition of aggregates.
indicated below:
IS No. Title 4 DATA FOR MIX
269 : 2015 Specification for ordinary PROPORTIONING
Portland cement (sixth revision) 4.1 The following data are required for mix
383 : 2016 Specification for coarse and fine proportioning of a particular grade of concrete:
aggregates for concrete (second
revision) a) Grade designation;
456 : 2000 Code of practice for plain and b) Type of cement, and grade of cement (if
reinforced concrete (fourth applicable);
revision) c) Maximum nominal size of aggregate;
1199 (Part 6) : 2018 Fresh concrete — Methods d) Minimum cement/cementitious materials
of sampling, testing and content and maximum water-cement/
analysis: Part 6 Tests on cementitious materials ratio to be adopted;
fresh self compacting or
concrete (first Exposure conditions as per Table 3 and
revision) (under publication) Table 5 of IS 456;
1489 Specification for Portland-
e) Workability required at the time of placement;
pozzolana cement
f) Transportation time;
(Part 1) : 2015 Fly ash based (third revision)
(Part 2) : 2015 Calcined clay based (third g) Method of placing;
revision) h) Degree of site control (good/fair) or value of
2386 (Part 3) : 1963 Methods of test for aggregates established standard deviation, if any;
for concrete: Part 3 Specific j) Type of coarse aggregate (angular/sub angular/
gravity, voids, absorption and
bulking
3812 (Part 1) : 2013 Specification for pulverized
fuel
2
gravel with some crushed particles/rounded production of concrete batches (for example
gravel/manufactured coarse aggregate); changes in the source of materials, mix
k) Type of fine aggregate (natural sand/ proportioning, equipment or technical
crushed stone or gravel sand/manufactured control), the standard deviation value shall be
sand/ mixed sand); separately calculated for such batches of
m) Maximum cement content; concrete.
n) Whether a chemical admixture shall or shall c) Standard de v iation to be
not be used and the type of chemical brought up-to-date — The calculation of the
admixture and the extent of use; standard d eviatio n shall b e b ro ught
p) Whether a mineral admixture shall or shall up -to-da te periodically and after every
not be used and the type of mineral change of mix proportioning. The standard
admixture and the extent of use; and deviation shall be checked every month
subject to minimum 30 test results to ensure
q) Any other specific requirement like early
that it is less than the value considered in mix
age strength requirements.
design. If higher, necessary modification
NOTE — Suitable reduction in water cement or water
cementitious material ratio shall be done after the mix
shall be done in the mix.
has been finalized based on trial mixes, to achieve the
4.2.1.2 Calculation of standard deviation
specific requirement of high early strength, if any. The
reduced ratio shall be fixed based on trials for the Calculate the standard deviation, S, of the strength
required early strength. These trials shall be carried out
after recalculating all the mix proportions. test results as follows.
4.2.1.2.1 For a single group of consecutive test results:
4.2 Target Strength for Mix Proportioning
n
∑ X( X)
i 2
−
In order that not more than the specified proportion
i 1
of test results are likely to fall below the where S
(n − 1)
characteristic
strength, the concrete mix has to be proportioned for
S = standard deviation of the group;
higher target mean compressive strength f ’ ck. The
margin over characteristic strength is given by the n = number of test results considered;
following relation: X = average of n test results considered; and
f’ck = fck + 1.65 S Xi = individual test result.
or 4.2.1.2.2 For two groups (mixes) of consecutive test
f’ck = fck + X results of same grade:
whichever is higher.
where (n − 1) s 2  − 1) s 2
(n1
S 1 2 2
f’ck = target mean compressive strength at 28 (n1  n2 − 2)

days, in N/mm2; where
fck = characteristic compressive strength at 28 S = standard deviation for the two groups
days, in N/mm2; combined;
S = standard deviation, in N/mm2 (see 4.2.1); s,s = standard deviation for group 1 and 2,
and
1 2
X = factor based on the grade of concrete, as
respectively, calculated as per 4.2.1.2.1;
per
and
Table 1.
n1, n2 = number of test results in group 1 and 2,
4.2.1 Standard Deviation
respectively, where both n1 and n2 shall
The standard deviation for each grade of concrete not be less than 10, and n1+ n2 shall not
shall be calculated separately. be less than 30.
4.2.1.1 Standard deviation based on test strength of 4.2.1.3 Assumed Standard
samples deviation
Where sufficient test results for a particular grade of
a) Number of test results of samples — The
concrete are not available, the value of standard
total number of test strength of samples
deviation given in Table 2 may be assumed for the
required t o con s ti tut e an ac cep t abl e
proportioning of mix in the first instance. As soon as
r e c o r d fo r calculation of standard
the results of samples are available, actual
deviation shall be not less than 30.
calculated standard deviation shall be used and the
b) In case of significant changes in concrete — mix may be proportioned suitably. However, when
When significant changes are made in the adequate past records for a similar grade exist and it
is justified to adopt a value of
standard deviation different from that shown in Table SECTION 2 ORDINARY AND STANDARD
1, it shall be permissible to use that value. GRADES OF CONCRETE
Table 1 Value of X 5 SELECTION OF MIX PROPORTIONS
(Clause 4.2)
5.1 Selection of Water-Cement Ratio
Sl Grade of Concrete Value of X
No. Different ce me nts, sup p le mentar y c eme
ntitious
(1) (2) (3) materials and aggregates of different maximum size,
i) M 10  grading, surface texture, shape and other
 5.0
M 15 characteristics may produce concrete of different
ii) M 20 compressive strength for the same free water-cement

M 25
5.5 ratio. Therefore, the relationship between strength
and free water-cement ratio should preferably be
iii) M 30 established for the materials actually to be used. In

M 35 the absence of such data, the preliminary free water-
M 40 cement ratio (by mass) (w/c) corresponding to the

M 45 6.5 compressive strength at 28 days may be selected
M 50 from the relationship shown in Fig.1, for the

M 55 expected 28 days strength of cement. The final w/c is
M 60 arrived at, based on the results of all the trials and
 any change in strength of cement shall get adjusted
iv) M65 and above 8.0 in the trials. In case, the actual strength of cement is
known, the curve corresponding to the actual strength
Table 2 Assumed Standard Deviation of cement may be used.
(Clause 4.2.1.3)
5.1.1 The water-cement ratio selected according to 5.1
Sl Grade of Concrete Assumed Standard shall be checked against the limiting water-cement
No. Deviation ratio for the requirements of durability and the lower
N/mm2
of the
(1) (2) (3) two values adopted.
i) NOTE — In case of water cement ratios on the upper limits of
M 10
 3.5 durability clause, it is required that the water content
M 15 contributed by the admixtures, also be considered in the
ii) calculations and the final water cement ratio shall be fixed
M 20 accordingly.
 4.0
M 25
5.1.2 Where supplementary cementitious materials
are used, that is, mineral admixtures, the water
iii) cementitious
M30 materials ratio (w/cm) shall be calculated, in
M35 accordance with Table 5 of IS 456 and this w/cm

M40 shall be in accordance with Table 3 and Table 5 of
 IS 456 or as specified.
M45 5.0
M50
 5.2 Estimation of Air Content
M55

M60 Approximate amount of entrapped air to be expected
in normal (non-air-entrained) concrete is given in
iv)
M 65  Table 3.
M 70 
 6.0 Table 3 Approximate Air Content
M 75 
(Clause 5.2)
M 80

Sl Nominal Maximum Size Entrapped Air, as
NOTES No. of Aggregate Percentage
1 The above values correspond to good degree of site control mm of Volume of Concrete
having proper storage of cement; weigh batching of all materials;
(1) (2) (3)
controlled addition of water; regular checking of all materials;
aggregate grading and moisture content; and regular checking of i) 10 1.5
workability and strength. Where there are deviations from the ii) 20 1.0
above, the site control shall be designated as fair and the values iii) 40 0.8
given in the above table shall be increased by 1 N/mm2.
2 For grades M65 and above, the standard deviation may also be 5.2.1 The actual values of air content can also be
established by actual trials based on assumed proportions, before adopted during mix proportioning, if the site data (at
finalizing the mix.
least 5 results) for similar mix is available.
Curve 1 : for expected 28 days compressive strength of 33 and < 43 N/mm2.
Curve 2 : for expected 28 days compressive strength of 43 and < 53 N/mm2.
Curve 3 : for expected 28 days compressive strength of 53 N/mm2 and above.
NOTES
1 In the absence of data on actual 28 days compressive strength of cement, the curves 1, 2 and 3 may be used for OPC 33, OPC 43 and
OPC 53, respectively.
2 While using PPC/PSC, the appropriate curve as per the actual strength may be utilized. In the absence of the actual 28 days
compressive strength data, curve 2 may be utilized.
FIG 1. RELATIONSHIP BETWEEN FREE WATER CEMENT RATIO AND 28 DAYS COMPRESSIVE STRENGTHS OF CONCRETE
FOR C EMENTS OF V ARIOUS EXPECTED 28 D AYS C OMPRESSIVE STRENGTHS
5.3 Selection of Water Content and Admixture aggregate and water reducing admixture will reduce
Content the water demand. On the other hand increased
The water content of concrete is influenced by a temperature, cement content, slump, water-cement
number of factors, such as aggregate size, aggregate ratio, aggregate angularity and a decrease in the
shape, aggregate texture, workability, water-cement proportion of the coarse aggregate to fine aggregate
ratio, cement and other supplementary cementitious will increase water demand.
materials type and content, chemical admixture and The quantity of mixing water per unit volume of
environmental conditions. An increase in aggregates concrete may be determined from Table 4. The water
size, a reduction in water-cement ratio and slump, content in Table 4 is for angular coarse aggregate and
and use of rounded for 50 mm slump. The water estimate in Table 4 can be
reduced by
approximately 10 kg for sub-angular aggregates, 15 cementitious materials content, as per Table 5 of
kg for gravel with some crushed particles and 20 kg IS 456.
for rounded gravel to produce same workability. For
the desired workability (other than 50 mm slump), the The cementitious materials content so calculated
required water content may be increased or decreased shall be checked against the minimum content for
by about 3 percent for each increase or decrease of 25 the requirements of durability as per IS 456 or as
mm slump or may be established by trial. This specified and greater of the two values may be
illustrates the need for trial batch testing of the given adopted. The maximum cement content shall be in
materials as each aggregate source is different and can accordance with IS 456 or as specified.
influence concrete properties. The water so calculated 5.4.2 The percentage of fly ash/GGBS to be used has
can be reduced by use of chemical admixture to be decided based on the project requirement and
conforming to IS 9103. Water reducing admixture the quality of these materials.
or super plasticizing admixtures usually decrease
water content by 5 to 10 percent and 20 to 30 percent 5.5 Estimation of Coarse Aggregate Proportion
and above respectively at appropriate dosages.
5.5.1 Aggregates of essentially the same nominal
The requirement of water content and/or chemical maximum size, type and grading will produce
admixture content may increase with the addition of concrete of satisfactory workability when a given
high dosages of mineral admixture. The guidelines volume of coarse aggregate per unit volume of total
on selecting appropriate water reducing admixture aggregate is used. Approximate values for this
and its dosages are given in Annex G. aggregate volume ar e given in Tab le 5 for a
Table 4 Water Content per Cubic Metre water-cement/wate r- cementitious materials ratio
of Concrete For Nominal Maximum Size of 0.5, which may be suitably adjusted for other
of Aggregate ratios, the proportion of volume of coarse aggregates
(Clause 5.3) to that of total aggregates is increased at the rate of
0.01 for every decrease in
5
Sl Nominal Maximum Size of Water Content1) water-cement/cementitious materials ratio by 0.05
No. Aggregate kg
mm and decreased at the rate of 0.01 for every increase in
water-
(1) (2) (3) cement ratio by 0.05.
i) 10 208
ii) 20 186
It can be seen that for equal workability, the volume
iii) 40 165 of coarse aggregate in a unit volume of concrete
is
1)
Water content corresponding to saturated surface dry aggregate. dependent only on its nominal maximum size and
grading zone of fine aggregate. Differences in the
NOTES
1 These quantities of mixing water are for use in computing
amount of mortar required for workability with
cement/cementitious materials content for trial different aggregates, due to differences in particle
batches. shape and grading, can be adjusted by changing
2 On account of long distances over which concrete needs to be
carried from batching plant/RMC plant, the concrete mix is
coarse to fine aggregate ratio. Generally higher fine
generally designed for a higher slump initially than the slump aggregate content is required for crushed angular
required at the time of placing. The initial slump value shall coarse aggregates due to increased surface area.
depend on the distance of transport and loss of slump with time.
5.5.2 For more workable concrete mixes which is
5.4 Calculation of Cement/Cementitious sometimes required when placement is by pump or
Materials when the concrete is required to be worked around
Content congested reinforcing steel, it may be desirable to
5.4.1 The cement and supplementary cementitious r educe t he estimated co arse aggr egate
materials content per unit volume of concrete may be content determined using Table 5 up to 10 percent.
calculated from the free water-cement ratio (see 5.1) However, caution shall be exercised to assure that the
and the quantity of water per unit volume of concrete. resulting slump, water-cement/cementitious materials
In certain situations, while using part replacement of ratio and strength properties of concrete are
cement by fly ash, ground granulated blast furnace consistent with the r e co mmend ati o ns o f I S 4 5
slag (GGBS), silica fume, and other mineral 6 and meet p r o j e ct specification requirements
admixtures, increase in cementitious materials as applicable.
content may be warranted, particularly if fly ash is
5.6 Combination of Different Coarse Aggregate
20 percent or more. The decision on increase in
Fractions
cementitious materials content and its percentage
may be based on experience and trials; or the The coarse aggregate used shall conform to IS 383.
cementitious materials content so calculated may Coarse aggregates of different sizes may be
be increased by 10 p er cent fo r preliminary trial. combined in suitable proportions so as to result in
The water-cementitious materials ratio s hal l b e r e an overall
calculat e d , b a s ed o n t he in cr eased
6
Table 5 Volume of Coarse Aggregate per Unit Volume of Total Aggregate for Different Zones of
Fine
Aggregate for Water-Cement/Water-Cementitious Materials Ratio of 0.50
(Clause 5.5)
Sl Nominal Maximum Size Volume of Coarse Aggregate per Unit Volume of Total Aggregate for Different Zones of Fine
No. of Aggregate Aggregate
mm
Zone IV Zone III Zone II Zone I
(1) (2) (3) (4) (5) (6)
i) 10 0.54 0.52 0.50 0.48
ii) 20 0.66 0.64 0.62 0.60
iii) 40 0.73 0.72 0.71 0.69
NOTES
1 Volumes are based on aggregates in saturated surface dry condition.
2 These volumes are for crushed (angular) aggregate and suitable adjustments may be made for other shape of aggregate.
3 Suitable adjustments may also be made for fine aggregate from other than natural sources, normally, crushed sand or mixed sand may
need lesser fine aggregate content. In that case, the coarse aggregate volume shall be suitably increased.
4 It is recommended that fine aggregate conforming to Grading Zone IV, as per IS 383 shall not be used in reinforced concrete unless
tests have been made to ascertain the suitability of proposed mix proportions.
grading conforming to Table 7 of IS 383 for percent of the pre-selected value, while satisfying the
particular nominal maximum size of aggregate. workability requirements as well.
5.7 Estimation of Fine and Coarse Aggregate M ix No. 2 to 4 no r ma l l y pr ov ide s s uff ic
Contents i en t information, including the relationship
between compressive strength and water-cement
With the completion of procedure given in 5.4, all the
ratio, from which the mix proportions can be
ingredients have been estimated except the coarse
finalized, such that the strength and durability
and fine aggregate content. These quantities are
requirements are also satisfied. Additional field
determined by finding out the absolute volume of
trials are recommended particularly for workability
cementitious materials, water and the chemical
requirements. The concrete for field trials shall be
admixture; by dividing their mass by their respective
produced by methods of actual concrete production.
specific gravity, multiplying by 1/1 000 and
subtracting the result of their summation from unit 5.8.1 Reporting
volume (excluding the volume of entrapped air). The mix design report shall include the following:
The values so obtained are divided into coarse and
a) Period of testing (starting and ending date);
fine aggregate fractions by volume in accordance
with coarse aggregate proportion already dete b) Details of work/type of structure, if
rmined in 5.5. T he coarse and fine aggregate provided; c) All the data provided for the mix
contents are then determined by multiplying their design as
volume with their respective specific gravities and per 4.1, and deviations from IS 456, if any;
multiplying by 1 000. d) Relevant test data of different materials for
the purpose of mix proportioning;
5.8 Trial Mixes
e) Details of materials such as brand of cement,
The calculated mix proportions shall be checked by manufacturing date (week/year) percentage
means of trial batches. of pozzolana/slag, etc, as per
manufacturers ce r t if i c ate; so ur ce o f
Workability of the trial mix No. 1 shall be measured.
co ar se an d fin e aggregates (if
The mix shall be carefully observed for freedom from
provided), etc;
segregation and bleeding and its finishing properties.
If the measured workability of Trial Mix No. 1 is f) Details of the trials conducted; and
different from the stipulated value, the water and/or g) Recommended mix proportions.
admixture content shall be adjusted suitably. With 5.9 Illustrative Examples
this adjustment, the mix proportion shall be
recalculated keeping the free water-cement/water- An illustrative example of concrete mix
cementitious materials ratio at the pre-selected proportioning is given in Annex A. Another
value, which will comprise Trial Mix No. 2. In illustrative example of mix proportioning of concrete
additional two more Trial Mixes No. 3 and 4 shall be using fly ash and using slag is given in Annex B and
made with the water content same as Trial mix No. 2 Annex C, respectively. These examples are merely
and varying the free water- cement/cementitious illustrative to explain the procedure and the actual
materials ratio by about ± 10 mix proportioning shall be based on trial batches
with the given materials.
7
SECTION 3 HIGH STRENGTH GRADES OF IS 383. Generally, for high strength, a fine aggregate
CONCRETE of coarser size is preferred (Zone I or Zone II), due to
availability of high fines content from the
6 HIGH STRENGTH CONCRETE (GRADE M
cementitious materials.
65
AND ABOVE) 6.1.4 Chemical
High strength concrete is the concr ete that has Admixtures
characteristic compressive strength of 65 N/mm2 or High strength concrete mixes usually have a low
more. This section provides the guidance for water- cementitious materials ratio (w/cm). These
selecting mix proportion for M65 or above. low w/cm ratios are generally only attainable with
high-range water-reducing admixtures (HRWRA).
Usually, for high strength concrete mixes specially
PCE type (Poly carboxylate ether based) super
s el ect e d ceme nt i ti o us mat e ri a ls and c
plasticisers which reduce water content by 30 percent
hemi ca l admixtures, that is, super plasticizers are
or above at appropriate dosages, maybe used.
used, and achieving a low water–cementitious
materials ratio (w/ cm) is considered essential. 6.2 Concrete Mix Proportioning
The procedure for proportioning high strength 6.2.1 Target Strength for Mix
concrete is similar to that required for Proportioning
ordinary/standard strength concrete. The procedure
consists of series of steps that, whe n c o mp l e t e d See 4.2.
, p r o vi d e a mi xtu r e me e t ing workability, 6.2.2 Selection of Maximum Size of Aggregate
strength and durability requirements based on the
combined properties of the individually selected and Based on the strength requirement, the maximum size
proportioned ingredients. of aggregates is generally restricted to 20 mm;
however, for grades M80 and above, aggregates of
6.1 Materials maximum size 10.0 mm to 12.5 mm may be
preferable.
Materials shall be selected, proportioned and
controlled carefully to achieve effective production 6.2.3 Estimation of Air Content
of high strength concrete. To achieve high strength
Approximate amount of entrapped air to be expected
concrete optimum proportions shall be selected,
in normal (non-air-entrained) concrete is given in
considering the cement and other cementitious
Table 6.
materials properties, aggregate quality, aggregate
gradation, paste volume, Table 6 Approximate Air Content
(Clause 6.2.3)
admixture type and dosage and mixing. Sl Nominal Maximum Size Entrapped Air, as
No. of Aggregate Percentage
6.1.1 Cementitious Materials mm of Volume of Concrete
Proper selection of type of cement is very important (1) (1) (1)
step for the production of high strength concrete. Fly i) 10.0 1.0
ii) 12.5 0.8
ash, silica fume, ground granulated blast furnace slag iii) 20.0 0.5
(GGBS) or metakaoline are widely used as
cementitious
and pozzolanic ingredients in high strength Aggregate
concrete.
The fine aggregate shall meet the requirements of
6.1.2 Coarse
Aggregate
In the proportioning of high strength concrete, the
aggregates require special consideration and they
greatly influence the strength and other properties of
concrete. Therefore, the coarse aggregate shall be
strong, sufficiently sound, free of fissures or weak
planes, clean and free of surface coating and shall
meet the requirement of IS 383. Generally crushed
stone aggregates with impact/crushing value not
greater than
22 percent and combined flakiness and elongation
index not more than 30 percent have been found
suitable for high strength concrete. 8
6.1.3 Fine
6.2.3.1 The actual values of air content can also be
adopted during mix proportioning if, the site data (at
6.2.4 Selection of Water Content and Admixture
Content
The quantity of water required to produce a given
workability is influenced by many factors, including
the maximum size, particle shape and grading of the
aggregate. The demand of water content is also
influenced by the quantity of cement, pozzolanic
material and the type of chemical admixture used.
PCE type (Polycarboxylate ether based) super
plasticisers which reduce water content by 30 percent
or above at appropriate dosages, maybe used.
However, trial batching is the most effective way to
determine the best proportions for the ingredients to
be used. Table 7 gives estimates of water content for
9
high strength concrete without chemical admixtures. cementitious materials ratio (see 6.2.5) per unit
The given water content is for 50 mm slump. For the volume of concrete. However, this must satisfy the
desired workability (other than 50 mm slump), the specification of maximum or minimum limit on the
required water content may be increased or decreased amount of cementitious material as per IS 456.
by about 3 percent for each increase or decrease
I f c e me nt co n te nt ( no t in c lu d in g a n y
of 25 mm slump or may be established by trial. These
mine r a l admixtures) more than the maximum
quantities of mixing water are maximum for well-
cement content as given in IS 456 is to be used, it
shaped , clean, angular and well gr ad ed
shall be ensured that the special consideration has
coarse aggregate. Since the particle shape and
been given in design to the increased risk of cracking
surface texture of fine aggregate can significantly
due to drying shrinkage, or to early thermal cracking
influence the mixing water demand, the water
and to the increased risk of damage due to alkali
requirement may be different from the values given in
silica reaction.
Table 7 and shall be established by trials. The water
so calculated shall be reduced by use of hi gh r a T he reco mmended dosage s of different
nge wa t e r r e d uci ng a dmi xt ur e s conforming mineral admixtures materials for high strength mixes
to IS 9103. are given in Table 9.
The requirement of water content and/or chemical 6.2.7 Estimation of Coarse Aggregate
admixture content may increase with the addition of Proportion
high dosages of mineral admixture. The guidelines The optimum content of the coarse aggregate
on selecting appropriate water reducing admixture depends on its strength and maximum nominal size
and its dosages are given in Annex G. of coarse aggregate. For proportioning of ordinary
NOTE — In case of water-cement ratios on the upper limits of and standard grades of concrete, the optimum
durability clause it is required that the water content volume of coarse aggregate is given as a function of
contributed by the admixtures shall also be considered in the the maximum size of coarse aggregate and grading
calculations and the final water-cement ratio shall be fixed
accordingly. zone of fine aggregate. However, high strength
grades of concrete are not dependent on the fine
6.2.5 Selection of Water-Cementitious Materials
aggregate to provide fines for lubrication and
Ratio
consolidation of the fresh concrete as the mixes have
(w/cm)
high content of cementitious material. The
The recommended values for w/cm for high strength recommended coarse aggregate volume per unit
concrete made with silica fume and HRWRA as a volume of total aggregate for different zones of fine
function of maximum size aggregates to achieve aggregate is given in Table 10.
different target compressive strength at 28 days, is
given in Table 8. In case, other cementitious For more workable concrete mixes which is
materials such as fly ash, ggbs are also used, the sometimes required when placement is by pump or
cementitious material content shall be suitably when the concrete is required to be worked around
increased and the water- cementitious material ratio congested reinforcing steel, it may be desirable to
shall be recalculated based on the total cementitious reduce the estimated coarse aggregate content
material used. determined using Table10 up to 5 percent. However,
caution shall be exercised to assure that the resulting
6.2.6 Calculation of Cementitious Material slump, water- cement ratio and strength properties of
Content concrete are consistent with the recommendations of
The cement and supplementary cementitious IS 456 and meet project specification requirements
material content per unit volume of concrete may be as applicable
calculated from the quantity of water (see 6.2.4) and
the free water-
Table 7 Water Content per Cubic Metre of Concrete for Nominal Maximum Sizes of
Aggregate
(Clause 6.2.4)
Sl Nominal Maximum Size of Aggregate Maximum Water Content (see Note 1)
3
No. mm kg/m
(1) (2) (3)
i) 10.0 200
ii) 12.5 195
iii) 20.0 186
NOTES
1 Water content corresponding to saturated surface dry
aggregate.
2 These quantities of mixing water are for use in computing cement/cementitious material content for trial
batches.
3 On account of long distances over which concrete needs to be carried from batching plant/RMC plant, the concrete mix is generally
designed for a higher slump initially than the slump required at the time of placing. The initial slump value shall depend on the distance
of transport and loss of slump with time. Accordingly the adjustment for water content/admixture dosage shall be made for the higher
initial slump value.
Table 8 Recommended w/cm for High Strength Concrete made with HRWRA
(Clause 6.2.5)
Sl Target Compressive Strength at 28 Days Water–Cementitious Materials Ratio
2
No. N/mm
Nominal Maximum Size of Aggregate
10.0 mm 12.5 mm 20.0 mm
(1) (2) (3) (4) (5)
i) 70 0.36 0.35 0.33
ii) 75 0.34 0.33 0.31
iii) 80 0.32 0.31 0.29
iv) 85 0.30 0.29 0.27
v) 90 0.28 0.27 0.26
vi) 100 0.26 0.25 0.24
NOTE — The recommended w/cm are for 28 days cement strength 53 MPa and above; for cement of other strength values, suitable
adjustments may be made by reducing the w/cm.
6.2.8 Estimation of Fine and Coarse Aggregate additional two more Trial Mixes No. 3 and 4 shall be
Contents made with the water content same as Trial mix No. 2
With the completion of procedure given in 6.2.4, and varying the free water-cement/cementitious
6.2.5 and 6.2.6, all the ingredients would have been materials ratio by ±10 percent of the preselected
estimated except the coarse and fine aggregate value, while satisfying the workability requirements
content. These quantities are determined by finding as well.
out the absolute volume of cementitious material, Mix No. 2 to 4 normally provides sufficient
water and the chemical admixture; by dividing their information, including the relationship between
mass by their respective specific gravity, multiplying compressive strength and water-cementitious
by 1/1 000 and subtracting the result of their materials ratio, from which the mix proportions can
summation from unit volume excluding the volume be finalized. Additional field trials a r e r e c omme
of entrapped air. The values so obtained are divided nd e d p ar ticular ly fo r wo r ka b ility
into coarse and fine aggregate fractions by volume requirements. The concrete for field trials shall be
in accordance with coarse aggregate proportion produced by methods of actual concrete production.
already determined in 6.2.7. The coarse and fine
aggregate contents are then determined by 6.2.10 Reporting
multiplying their volume with their respective The mix design report shall include the following:
specific gravities and multiplying by 1 000.
6.2.9 Trial b) Details of work/type of structure, if
Mixes
provided; c) All the data provided for the mix
The calculated mix proportions shall be checked by design as
means of trial batches. per 4.1, and deviations from IS 456, if any;
Workability of the trial mix No. 1 shall be measured. d) Relevant test data of different materials for
The mix shall be carefully observed for freedom the purpose of mix proportioning;
from segregation and bleeding and its finishing e) Details of materials such as brand of cement,
properties. If the measured workability of Trial Mix manufacturing date (week/year) percentage
No. 1 is different from the stipulated value, the water of pozzolana/slag, etc, as per
and/or admixture content shall be adjusted suitably. manufacturers ce r t if i c ate; so ur ce o f
With this adjustment, the mix proportion shall be co ar se an d fin e aggregates (if
recalculated keeping the free water-cement ratio at provided), etc;
the pre-selected value, which will comprise Trial f) Details of the trials conducted; and
Mix No. 2. In
g) Recommended mix proportions.
Table 9 Recommended Dosages of Mineral Admixtures Materials for High Strength

Mixes
Sl
(Clause 6.2.6)
No. Mineral Admixtures Recommended Dosages, Percentage by Mass of
Total Cementitious Materials
(1) (2) (3)
i) Fly ash 15 - 30
ii) Ground granulated blast furnace slag 25 - 50
iii) Metakaoline 5 - 15
iv) Silica fume 5 - 10
Fine
Aggregate for Water-Cement/Water-Cementitious Material Ratio of 0.30
(Clause 6.2.7)
Sl Nominal Maximum Size of Volume of Coarse Aggregate per Unit Volume of Total Aggregate for Different
No. Aggregate Zones of Fine Aggregate
mm
Zone III Zone II Zone I
(1) (2) (3) (4) (5)
i) 10.0 0.56 0.54 0.52
ii) 12.5 0.58 0.56 0.54
iii) 20.0 0.68 0.66 0.64
NOTES
1 Volumes are based on aggregates in saturated surface dry
condition.
2 These volumes are for crushed (angular) coarse aggregate and suitable adjustments may be made for other shape of
aggregate.
3 Suitable adjustments may also be made for fine aggregate from other than natural sources, normally, crushed sand or mixed sand
having higher fine content (passing 150 micron sieve), which may need lesser fine aggregate content. In that case, the coarse aggregate
volume may be suitably increased.
6.3 Illustrative Examples 7.2.1 Filling Ability (flowability)

An illustrative example of concrete mix This is the ability of fresh concrete to flow into and
proportioning for high strength concrete is given in fill all spaces within the formwork, under its own
Annex D. These examples a re mere ly illustra weight. Slump-flow test is performed to test the
tive to e xp lain the procedure and the actual mix flowability. Slump-flow value describes the
proportioning shall be based on trial batches with the flowablity of a fresh mix in unconfined condition.
given materials. Visual observation during the test can provide
SECTION 4 SELF COMPACTING additional information on the segregation resistance
CONCRETE and uniformity.
7 GENERAL The following are typical slump-flow classes for a

range of applications:
Self compacting concrete (SCC) is highly flowable,
non-segregating concrete that fills uniformly and a) SF1 (slump flow 550 mm - 650 mm). This
completely every corner of formwork by its own class of SCC is appropriate for:
weight and encapsulate reinforcement without any 1) Unreinforced or lightly reinforced
vibration, whilst maintaining homogeneity. concrete structures that are cast from the
top with free displacement from the
7.1 Application Area delivery point (for example, housing
Self compacting concrete (SCC) may be used in slabs).
precast concrete applications or for concrete placed on 2) Casting by a pump injection system (for
site. SCC is used to cast sections with highly example, tunnel linings).
congested reinforcement and in areas that present 3) Sections that are small enough to
restricted access to placement and consolidation, prevent long horizontal flow (for
including the construction of tunnel lining sections and example, piles and some deep
the casting of hybrid concrete- filled steel tubular foundations).
columns. It may be manufactured in a site batching b) SF2 (slump flow 660 mm - 750 mm) is
plant or in a ready-mixed concrete plant and delivered suitable for normal applications (for
to site by truck mixer. It may be placed either by example, walls, columns).
pumping or pouring into horizontal or vertical forms.
c) SF3 (slump flow 760 mm — 850 mm) is
7.2 Features of Fresh Self Compacting Concrete used for vertical applications in heavily
A co ncr ete mix can only b e classifie d as se reinforced structures, structures with
lf- compacting concrete, if the requirements for all complex shapes, or for filling under
below mentioned characteristics are fulfilled: formwork. SF3 will often give better surface
finish than SF2 for normal vertical
a) Filling ability (Flowability), applications but segregation resistance is
b) Passing ability, more difficult to control.
c) Segregation resistance, and
7.2. 2 P a ss in g A b ility ( F re e f rom B loc k i
d) Viscosity ng at
T he a b o ve tes ts sh all be c ar r i ed o ut a Reinforcement)
s p er Passing ability describes the capacity of the fresh mix
IS 1199 (Part 6). to flow through confined spaces and narrow openings
such as areas of congested reinforcement without
segregation. If
there is little or no reinforcement, there may be no need negative effects on surface finish and sensitivity to
to specify passing ability as a requirement. L-box test stoppages or delays between successive lifts.
is performed to check the passing ability. The minimum
For V1 class, the time taken to pass the concrete from
ratio of the depth of the concrete in the horizontal
V-funnel shall be  8 s and for V2 class the time
section relative to the depth of concrete vertical section
taken to pass the concrete from V-funnel shall be
is considered to be 0.8. If the SCC flows as freely as
between 8 s and 25 s.
water, it will be completely horizontal, and the ratio
will be equal to 1.0. 8 MIX PROPORTIONING
7.2.3 Segregation Resistance (Stability) 8.1 Mix Proportioning Principles
This is the ability of fresh concrete to remain a) Lower coarse aggregate content,
homogeneous in composition while in its fresh state. b) Increased paste content,
Segregation resistance (sieve) test is performed to c) Low water/powder ratio (see Note),
check this property of fresh concrete.
d) Increased superplasticiser, and
After sampling, the fresh concrete is allowed to stand e) Sometimes a viscosity modifying admixture.
for 15 min and any separation of bleed water is noted.
NOTE — Powder refers to materials of particle size smaller
The top part of the sample is then poured into a sieve than 0.125 mm. It includes this size fraction from cement,
with 4.75 mm square apertures. After 2 min, the mineral admixtures and aggregate. Water/powder ratio shall be
weight of material which has passed through the 0.85 to 1.10 by volume.
sieve is recorded. The segregation ratio (SR) is then 8.2 Mix Proportioning Approach
calculated as the proportion of the sample passing
through the sieve. Laboratory trials shall be used to verify properties of
the initial mix composition with respect to the
There are two classes of segregation resistance, specified characteristics and classes. If necessary,
namely SR1 and SR2. SR1 is generally applicable for adjustments to the mix composition shall then be
thin slabs and for vertical applications with a flow made. Once all requirements are fulfilled, the mix
distance of less than 5 m and a confinement gap shall be tested at full scale in the concrete plant and if
greater than 80 mm. SR2 is preferred in vertical necessary, at site to verify both the fresh and
applications if the flow distance is more than 5 m with hardened properties.
a confinement gap greater than 80 mm in order to take
The mix design is generally based on the approach
care of segregation during flow. For SR1 class
outlined below:
segregation resistance shall be 15 to
20 percent and for SR2 it shall be less than 15 percent. a) Determine the target average compressive
SR2 may also be used for tall vertical applications strength.
with a confinement gap of less than 80 mm if the flow b) Select the air content based on the specified
distance is less than 5 m, but if the flow is more than 5 nominal maximum size of aggregate and
m, a target SR value of less than 10 percent is concrete grade.
recommended. Segregation resistance becomes an c) Select water-cement/cementitious materials
important parameter with higher slump-flow classes ratio.
and/or the lower viscosity classes, or if placing d) Select the proportions for initial mix.
conditions promotes segregation. If none of these e) Select water content and cement/fly ash(or
apply, it is usually not necessary to specify a other supplementary cementitious material)
segregation resistance class. content.
7.2.4 Viscosity f) Select admixture content.
g) Select powder content and fine aggregate
Viscosity can be assessed by the V-funnel flow time
content.
as per IS 1199 (Part 6). Concrete with a low viscosity
will have a very quick initial flow and then stop. h) Select coarse aggregate content.
Concrete with a high viscosity may continue to creep j) Calculate volume of powder content and
forward over an extended time. determine water powder ratio by volume,
and make adjustments, if required.
A V-shaped funnel is filled with fresh concrete and
k) Work out the mix proportions for trial 1.
the time taken for the concrete to flow out of the
m) Produce the fresh SCC in the laboratory
funnel is measured and recorded as the V-funnel flow
mixer, perform the required tests as per 7.2,
time. The viscosity is divided into two classes, that
and make adjustments.
is, V1 and V2. V1 has good filling ability even with
congested reinforcement. It is capable of self- n) Test the properties of the SCC in the
leveling and generally has the best surface finish. V2 hardened state.
class viscosity is more likely to exhibit thixotropic p) Produce trial mixes in the plant mixer.
effects, which may be helpful in limiting the
formwork pressure or improving segregation
resistance. But it may cause
8.3 Typical Ranges of Mix Constituents for self compacting concrete is given in Annex E.
a) Sufficient amount of fines (< 0.125 mm) This example is merely illustrative and explains
preferably in the range of 400 kg/m 3 to the procedure to be adopted for self compacting
600 kg/m3, inclusive of suitable quantities of concrete. The actual mix proportioning shall be based
fine aggregate and mineral admixtures like on various trials with the given materials
fly ash in suitable proportions, may be used SECTION 5 MASS CONCRETE
for flowability while ensuring compliance
with engineering properties particularly 9 GENERAL
shrinkage. Fine aggregate content, typically, Mass concreting is used for structures like dams and
48 to 60 percent by mass of the total other massive structures. For such large structures,
aggregate, balances the volume of the other measures need to be taken to cope with the generation
constituents. of heat from hydration of cement and attendant
b) Water content between 150 to 210 kg/m3. volume change to minimize cracking.
c) Use of high range water reducing admixture The primary objective of proportioning for mass
like polycarboxylate ether based high range concrete is to establish economical mixes of proper
water reducing admixture (water reduction strength, durability and permeability with the best
> 30 percent) and sometimes also using a combination of available materials that will provide
viscosity modifying admixture (VMA) in adequate workability, easy placeability and least
appropriate dosages. temperature rise after placement.
In the event that satisfactory performance is not In mass concrete structures, generally lower grade of
obtained, consideration shall be given to a concrete (say M 15 or M 20) and higher sizes of
fundamental redesign of the mix. Depending on the coarse aggregates [maximum nominal size of
apparent problem, the following courses of action aggregate (msa)
might be appropriate: 40 mm, msa 80 mm and msa 150 mm] are used. In
certain cases, like thick raft foundation, retaining
1) Adjust the water/powder ratio and test the
wall, etc, mass concreting may be of higher grade of
flow and other properties of the paste.
concrete.
2) Try different types of additions (if
available). When a mineral admixture is included in the concrete
3) Adjust the proportions of the fine aggregate as a part of the cementitious material, the mix
and the dosage of superplasticiser. proportioning remains the same. Attention shall be
given to the following:
4) Consider using a viscosity modifying agent
to reduce sensitivity of the mix. a) The water requirement may change,
5) Adjust the proportion or grading of the b) Early age strength may become critical, and
coarse aggregate. c) For maximum economy, the age at which
8.3.1 Reporting design strength is attained should be greater.
9.1 Data for Mix Proportioning
The mix design report shall include the following:
In addition to the data requirements mentioned in 4.1,
the following additional data are required for mix
b) Details of work/type of structure, if proportioning for mass concrete:
provided; c) All the data provided for the mix
a) Expected maximum placing temperature.
design as
b) Air content range in case of air entrained
per 4.1, and deviations from IS 456, if any;
concrete.
d) Relevant test data of different materials for
c) Test ages for strength.
the purpose of mix proportioning;
e) Details of materials such as brand of cement, 9.2 Target Strength for Mix Proportioning
manufacturing date (week/year) percentage The target strength calculated as per 4.2 shall be
of pozzolana/slag, etc, as per increased by 20 percent for 80 mm msa, and by 25
manufacturers certificate; source of percent for 150 mm msa. This is to account for higher
coarse and fine aggregates (if provided), strength achieved after wet sieving the concrete
etc; through
f) Details of the trials conducted; and 40 mm sieve for making 150 mm cubes for strength
g) Recommended mix proportions. testing. This increase in target strength due to wet
sieving effect is only for cube test results and not to
8.4 Illustrative Example
be considered for selection of water cement ratio.
An illustrative example of concrete mix
proportioning
In case, any other relationship is established at site, Air entrainment in mass concrete (for 150 mm msa
the same may also be adopted in place of 20 and 25 and 80 mm msa) is considered useful for various
percent. reasons. Air entrainment in mass concrete permits a
marked improvement in durability (particularly
9.3 Estimation of Air Content
under freezing and thawing conditions),
Approximate amount of entrapped air to be expected improvement in plasticity and workability and
in normal (non-air-entrained) concrete is given in reduction in segregation and bleeding. The effect of
Table 11. air entrainment on the strength of mass concrete
Table 11 Approximate Air Content shall be considered in the design of mass concrete
(Clause 9.3) itself; that is, the reduction in strength, shall be
compensated in the mix trials.
Sl Nominal Maximum Entrapped Air, as Percentage Generally, 3 to 4 percent air content is recommended
No. Size of Aggregate of Volume of Concrete
mm
for 150 mm msa and 3.5 to 4.5 percent air content is
(1) (2) (3) recommended for 80 mm msa. The air content when
i)
40 0.8
determined on mixtures passing through 40 mm sieve
ii) shall be higher by 1.5 to 2 percent than the values
80 0.3
iii)
150 0.2 indicated above.
9.3.1 The actual values of air content can also be
Table 12 Water Content per Cubic Metre of
adopted during mix proportioning if, the site data (at
Concrete for Nominal Maximum Size of
Aggregate (Clause 9.4)
(1)
9.4 Selection of Water Content and Admixture Sl Nominal Maximum Size of Water Content
No. Aggregate kg
Content mm
The water content of concrete is influenced by a (1) (2) (3)
number
of factors, such as aggregate size, aggregate shape, i) 40 165
ii) 80 145
aggregate texture, workability, water-cement ratio, iii) 150 125
cement and other supplementary cementitious
materials
( typ e and c o nten t) , chemical ad mi xt u r e appropriate dosages.
an d environmental conditions. An increase in
aggregates size, a reduction in water-cement ratio and
slumps, and use of rounded aggregate and water
reducing admixture will reduce the water demand.
On the other hand increased temperature, cement
content, slump, water- cement ratio, aggregate
angularity and a decrease in the proportion of the
coarse aggregate to fine aggregate will increase water
demand.
The quantity of mixing water per unit volume of
concrete may be determined from Table 12. The
water content in Table 12 is for angular coarse
aggregate and for 50 mm slump. The water estimate
in Table 12 can be reduced by approximately 20 kg
for rounded gravel of 40 mm msa, 15 kg for rounded
gravel of 80 mm msa a nd 10 k g fo r 1 5 0 mm
msa , t o produc e s a me workability. For the
desired workability (other than 50 mm slump), the
req uired wa ter content ma y be increased or
decreased by about 3 percent for each increase or
decrease of 25 mm slump or may be established by
trial. This illustrates the need for trial batch testing of
the given materials as each aggregate sour ce is d i
ffer ent and can influe nce conc r ete properties.
The water so calculated can be reduced by use of
chemical admixture conforming to IS 9103. Water
reducing admixture or plasticizing admixtures have
been found effective in mass concrete mixes, and
usually decrease water content by 5 to 10 percent at
1)
Water content corresponding to saturated surface dry
aggregate.
NOTES
1 The recommended values of water content for different msa of
aggregates are for non-air-entrained concrete. The values will be
decreased by 8 kg in case of air-entrained concrete.
2 These quantities of mixing water are for use in
computing cement/cementitious materials content for trial
batches.
3 On account of long distances over which concrete needs to be
carried from batching plant/RMC plant, the concrete mix is
generally designed for a higher slump initially than the slump
required at the time of placing. The initial slump value
shall depend on the distance of transport and loss of slump with
time.
9.5 Selection of Water Cement

Ratio.
The water cement ratio shall be selected as per Fig. 1
for the target strength calculated as per 9.2 without
considering the increase of strength by 20-25 percent
due to wet sieving effect.
9.6 Calculation of Cement/Cementitious

Materials
Content
9.6.1 The cement and supplementary cementitious
materials content per unit volume of concrete may be
calculated from the free water-cement ratio (see 9.5)
and the quantity of water per unit volume of
concrete.
In certain situations, while using part replacement of
cement by fly ash, ground granulated blast furnace
slag (GGBS), silica fume, etc, increase in
cementitious materials content may be warranted,
particularly if fly ash is 20 percent or more and
GGBS is 30 percent or more. The decision on
increase in cementitious
materials content and its percentage may be based on is required for crushed angular coarse aggregates due
experience and trials; or the cementitious materials to increased surface area.
content so calculated may be increased by 10 percent
for preliminary trial. The water cementitious 9.8 Estimation of Fine and Coarse Aggregate
materials ratio may be recalculated based on the Contents
increased cementitious materials content. With the completion of procedure given in 9.6, all the
The cementitious materials content so calculated ingredients have been estimated except the coarse
shall be checked against the minimum content for and fine aggregate content. These quantities are
the requirements of durability as per IS 456 or as determined by finding out the absolute volume of
specified and greater of the two values adopted. The cementitious materials, water and the chemical
maximum cement content shall be in accordance admixture; by dividing their mass by their respective
with IS 456 or as specified. specific gravity, multiplying by 1/1 000 and
subtracting the result of their summation from unit
9.6.2 The percentage of fly ash/GGBS to be used has volume. The values so obtained are divided into
to be decided based on the project requirement and coarse and fine aggregate fr actions by volume in
the quality of these materials. ac co rdanc e with coar se aggregate proportion
9.7 Estimation of Coarse Aggregate Proportion already determined in 9.7. The coarse and fine
aggregate contents are then determined by
Aggregates of essentially the same nominal multiplying their volume with their respective
maximum size, type and grading will produce specific gravities and multiplying by 1 000.
concrete of satisfactory workability when a given
volume of coarse aggregate per unit volume of total 9.9 Combination of Different Coarse Aggregate
aggregate is used. Approximate values for this Fractions
aggregate volume are given in Table 13 for a water- The coarse aggregate used shall conform to IS 383.
cement/water-cementitious materials ratio of 0.5, Coarse aggregates of different sizes, as given in Table
which may be suitably adjusted for other water- 7 and Table 8 of IS 383 may be combined in suitable
cement ratios, the proportion of volume of coarse proportions so as to result in an overall grading
aggregates to that of total aggregates is increased at conforming to Table 7 of IS 383 for 40 mm nominal
the rate of 0.01 for every decrease in water- cement maximum size of aggregate, and Table 14 for 80 mm
ratio by 0.05 and decreased at the rate of 0.01 for and 150 mm nominal maximum size of aggregates.
every increase in water-cement ratio by 0.05.
It can be seen that for equal workability, the volume 9.10 Placement and Workability
of coarse aggregate in a unit volume of concrete is Experience has demonstrated that large aggregate
dependent only on its nominal maximum size and mixtures, 150 mm msa and 80 mm msa require a
grading zone of fine aggregate. Differences in the minimum mortar content for suitable placing and
amount of mortar required for workability with workability properties. Table 15 gives the total
different aggregates, due to differences in particle absolute vol ume of mo r ta r ( C eme nt , p o z z o
shape and grading, can be adjusted by changing la na , wa t e r, admixture, air, and fine aggregate),
coarse to fine aggregate ratio. Generally higher fine which is suggested for use in mixtures containing
aggregate content large aggregate sizes.
Fine
Aggregate for Water-Cement/Water-Cementitious Materials Ratio of 0.50
(Clause 9.7)
Sl Nominal Maximum Size Volume of Coarse Aggregate per Unit Volume of Total Aggregate for Different Zones of
No. of Aggregate Fine Aggregate
mm
Zone IV Zone III Zone II Zone I
(1) (2) (3) (4) (5) (6)
i) 40 0.73 0.72 0.71 0.69
ii) 80 0.75 0.74 0.73 0.72
iii) 150 0.80 0.79 0.78 0.77
NOTES
1 Volumes are based on aggregates in saturated surface dry condition.
2 These volumes are for crushed (angular) aggregate and suitable adjustments may be made for other shape of aggregate.
3 Suitable adjustments may also be made for fine aggregate from other than natural sources, normally, crushed sand or mixed sand may
need lesser fine aggregate content. In that case, the coarse aggregate volume should be suitably increased.
Table 14 Grading Requirements for Coarse Aggregate for Mass Concrete
(Clause 9.9)
Sl IS Sieve Designation Percentage Passing for Graded Aggregate of Nominal Size
No. mm
150 mm 80 mm
(1) (2) (3) (4)
i) 150 100 100
ii) 80 55 - 65 100
iii) 40 29 - 40 53 - 62
iv) 20 14 - 22 26 - 34
v) 10 6 - 10 10 - 15
vi) 4.75 0 -5 0 -5
NOTE — In mass concreting, rounded aggregate is also used, and the fine aggregate requirement is on the lower side as compared to
crushed aggregate. Therefore, it is recommended that, for rounded aggregates, the percentage passing shall be towards the higher limit
of the range specified for various sieve sizes and for crushed aggregates, the percentage passing, shall be towards the lower limit of the
range specified for various sieve sizes. This recommendation is valid for grading requirements for 150 mm msa, and 80 mm msa, as
mentioned above, and for 40 mm msa as per Table 7 of IS 383.
These values shall be compared with those M ix No. 2 to 4 no r ma l l y pr ov ide s s uff ic

determined during the mix proportioning procedure i en t information, including the relationship
and appropriate adjustments made by either between compressive strength and water-cement
increasing or decreasing the fine aggregate, and ratio, from which the mix proportions can be
cementitous material contents, for improved finalized, such that the strength and durability
placeability and workability, requirements are also satisfied. Additional field
Table 15 Approximate Mortar Content for trials are recommended particularly for workability
Various Nominal Maximum Sizes of requirements. The concrete for field trials shall be
Aggregates (Clause 9.9) produced by methods of actual concrete production.
Sl Nominal Maximum Shape of Volume of
No. Size of Aggregate Aggregate Mortar Content 9.12 Reporting
mm m3
(1) (2) (3) (4) The mix design report shall include the following:
i) 150 Crushed 0.39 ± 0.01
ii) 150 Rounded 0.37 ± 0.01
iii) 80 Crushed 0.44 ± 0.01 b) Details of work/type of structure, if
iv) 80 Rounded 0.43 ± 0.01 provided; c) All the data provided for the mix
design as
9.11 Trial Mixes
per 4.1 and 9.1, and deviations from IS 456,
The calculated mix proportions shall be checked by if any;
means of trial batches. d) Relevant test data of different materials for
Workability of the trial mix No. 1 shall be measured. the purpose of mix proportioning;
The mix shall be carefully observed for freedom e) Details of materials such as brand of cement,
from segregation and bleeding and its finishing manufacturing date (week/year) percentage
properties. If the measured workability of Trial Mix of pozzolana/slag, etc, as per
No. 1 is different from the stipulated value, the water manufacturers ce r t if i c ate; so ur ce o f
and/or admixture content shall be adjusted suitably. co ar se an d fin e aggregates (if
With this adjustment, the mix proportion shall be provided), etc;
recalculated keeping the free water-cement ratio at f) Details of the trials conducted; and
the pre-selected value, which will comprise Trial Mix g) Recommended mix proportions.
No. 2. In addition, two more Trial Mixes No. 3 and 4
shall be made with the water content same as Trial 9.13 Illustrative Example
mix No. 2 and varying the free water- An illustrative example of concrete mix
cement/cementitious materials ratio by about ±10 proportioning for mass concreting is given in Annex
percent of the preselected value, while satisfying the F. This example is merely illustrative and explains
workability requirements as well. the procedure to be a d o p te d f o r mass co nc r
et i ng . T he a ct u al mi x proportioning shall be
based on various trials with the given materials.
ANNEX A
(Clause 5.9)
ILLUSTRATIVE EXAMPLE ON CONCRETE MIX PROPORTIONING
A-0 An example illustrating the mix proportioning for a concrete of M40 grade is given in A-1 to A-12.
A-1 STIPULATIONS FOR PROPORTIONING

a) Grade designation : M40
b) Type of cement : PPC conforming to IS 1489 (Part 1)
c) Maximum nominal size of aggregate : 20 mm
d) Minimum cement content and
maximum water-cement ratio to be adopted and/or Severe (for reinforced concrete)
: Exposure conditions as per Table 3
and Table 5 of IS 456
e) Workability : 75 mm (slump)
f) Method of concrete placing : Chute (Non pumpable)
g) Degree of site control : Good
h) Type of aggregate : Crushed angular aggregate
j) Maximum cement content not including fly ash : 450 kg/m3
k) Chemical admixture type : Superplasticizer - normal
A-2 TEST DATA FOR MATERIALS
a) Cement used : PPC conforming to IS 1489 (Part 1)
b) Specific gravity of cement : 2.88
c) Chemical admixture : Superplasticizer conforming to IS 9103
d) Specific gravity of
1) Coarse aggregate [at saturated surface dry : 2.74
(SSD) Condtion]
2) Fine aggregate [at saturated surface dry : 2.65
(SSD) Condtion]
3) Chemical admixture : 1.145
e) Water absorption
1) Coarse aggregate : 0.5 percent
2) Fine aggregate : 1.0 percent
f) Moisture content of aggregate [As per IS 2386 (Part 3)]
1) Coarse aggregate : Nil
2) Fine aggregate : Nil
g) Sieve analysis:
1) Coarse aggregate :
IS Sieve Sizes Analysis of Coarse Aggregate Percentage of Different Fractions Remarks
mm Fraction
I II I II Conforming
(20-10 mm) (10 - 4.75 mm) 60 percent 40 percent 100 percent
(1) (2) (3) (4) (5) (6) (7)
20 100 100 60 40 100
10 0 71.20 0 28.5 28.5 Conforming
4.75 9.40 3.7 3.7 to Table 7 of
2.36 0 IS 383
2) Fine aggregate : Conforming to grading Zone II of Table 9 of

IS 383
A- 3 TAR G ET S T RENG TH FOR M reduced. Based on trial data, the water content
I X PROPORTIONING reduction of 23 percent is considered while using
f’ck = fck+1.65 S superplasticizer at the rate 1.0 percent by weight of
or cement.
f’ck = fck + X Hence the water content
whichever is higher. = 191.58 × 0.77
where = 147.52kg≈ 148
kg
f’ck = target average compressive strength at
A-7 CALCULATION OF CEMENT
28 days,
CONTENT
Water-cement ratio = 0.36
148
fck = char acter istic co mpr e ssive stre ngth Cement content = = 411.11 kg/m3 ≈ 412
0.36 kg/m3
at
28 days,
From Table 5 of IS 456, minimum cement content
S = standard deviation, and for
X = factor based on grade of concrete. ‘severe’ exposure condition = 320 kg/m3
From Table 2, standard deviation, S = 5 N/mm2. 412 kg/m3> 320 kg/m3, hence, O.K.
From Table 1, X = 6.5. A-8 PROPORTION OF VOLUME OF COARSE

A GGR EGATE A N D F I NE AG GR EG
Therefore, target strength using both equations, that ET E CONTENT
is,
From Table 5, the proportionate volume of coarse
a) f’ck = fck+1.65 S aggregate corresponding to 20 mm size aggregate and
= 40+1.65 × 5 = 48.25 N/mm2 fine aggregate (Zone II) for water-cement ratio of 0.50
b) f’ck = fck + 6.5 = 0.62.
= 40 + 6.5 = 46.5 N/mm2 In the pr esent case wa ter-cement r atio is 0 .3
The higher value is to be adopted. Therefore, target 6. Therefore, volume of coarse aggregate is required
strength will be 48.25 N/mm2 as 48.25 N/mm2 > 46.5 to be increased to decrease the fine aggregate content.
N/mm2. As the water-cement ratio is lower by 0.14, the
proportion of volume of coarse, aggregate is
A-4 APPROXIMATE AIR CONTENT increased by 0.028 (at the rate of  0.01 for every ±
0.05 change in water- cement ratio). Therefore,
From Table 3, the approximate amount of entrapped
corrected proportion of
air to be expected in normal (non-air-entrained)
volume of coarse aggregate for the water-cement
concrete is 1.0 percent for 20 mm nominal maximum
ratio of 0.36 = 0.62 + 0.028 = 0.648.
size of aggregate.
Volume of fine aggregate content = 1 – 0.648 =
A-5 SELECTION OF WATER-CEMENT 0.352
RATIO
A-9 MIX CALCULATIONS
From Fig. 1, the free water-cement ratio required for
The mix calculations per unit volume of concrete
the target strength of 48.25 N/mm2 is 0.36 for OPC shall be as follows:
43 grade curve. (For PPC, the strength corresponding
to OPC 43 grade curve is assumed for the trial). This a) Total volume = 1 m3
is lower than the maximum value of 0.45 prescribed b) Volume of entrapped air in wet concrete =
for 0.01 m3
‘severe’ exposure for reinforced concrete as per Table c) Volume of cement
5 of IS 456.
Mass of cement 1
= 
0.36< 0.45, hence O.K. Specific gravity of cement 1 000
412 1
A-6 SELECTION OF WATER = 2.88  1 000
CONTENT
From Table 4, water content = 186 kg (for 50 mm = 0.143 m3
slump) for 20 mm aggregate. d) Volume of water
Mass of water 1
Estimated water content for 75 mm slump = 
Specific gravity of water 1 000
3 186
= 186 +
100 148 1
= 191.58 kg = 
1 1 000
As superplasticizer is used, the water content may be
= 0.148 m3
e) Volume of chemical admixture b) Coarse Aggregate (Dry)
(superplasticizer) (@ 1.0 percent
by mass of cementitious material) Mass of coarse aggregate in SSD condition
= Water absorption
1+ /
100
Mass of chemical admixture 1
= 
Specific gravity of admixture 1 000 1 234
= 0.5
1  /100
4.12  1 = 1 227.86 kg/m3  1 228 kg/m3
=
1.145 1 000
The extra water to be added for absorption by coarse
= 0.003 6 m3 and fine aggregate,
g) Volume of all in aggregate = [(a-b)-
1) For coarse aggregate
(c+d+e)]
= Mass of coarse aggregate in SSD condition
= [(1-0.01) – (0.143 + 0.148 + 0.0 036)]
–
= 0.695 m3 mass of coarse aggregate in dry condition
h) Mass of coarse aggregate = 1 234 – 1 228 = 6 kg
= g × Volume of coarse aggregate × Specific 2) For fine aggregate
gravity of coarse aggregate × 1 000
= Mass of fine aggregate in SSD condition –
= 0.695 × 0.648 × 2.74 × 1 000 mass of fine aggregate in dry condition
= 1 233.98 kg  1 234 kg = 648 – 642 = 6 kg
j) Mass of fine aggregate The estimated requirement for added water, therefore,
= g × volume of fine aggregate × Specific becomes
gravity of fine aggregate × 1 000
= 148 + 6 + 6 = 160 kg/m3
= 0.695 × 0.352 × 2.65 × 1 000
= 648.29 kg  648 kg A-12 MIX PROPORTIONS AFTER
A-10 MIX PROPORTIONS FOR TRIAL ADUSTMENT FOR DRY AGGREGATES
NUMBER 1 Cement = 412 kg/m3
Cement = 412 kg/m3 Water (to be added) = 160 kg/m3
Water = 148 kg/m3 Fine aggregate (Dry) = 642 kg/m3
Fine aggregate (SSD) = 648 kg/m3 Coarse aggregate (Dry) = 1 228 kg/m3
Coarse aggregate (SSD) = 1 234 kg/m3 Chemical admixture = 4.12 kg/m3
Chemical admixture = 4.12 kg/m3, Free water-cement ratio = 0.36
Free water-cement ratio = 0.36 A-13 The total mass of coarse aggregate shall be
NOTE — Aggregates shall be used in saturated surface dry divided into two fractions of 20 - 10 mm and 10 -
condition. If otherwise, when computing the requirement of
4.75 mm, in a suitable ratio, to satisfy the overall
mixing water, allowance shall be made for the free (surface)
moisture contributed by the fine and coarse aggregates. On the grading requirements for 20 mm max size aggregate
other hand, if the aggregates are dry, the amount of mixing as per Table 7 of IS 383. In this example, the ratio
water shall be increased by an amount equal to the moisture works out to be 60:40 as shown under A-2 (g).
likely to be absorbed by the aggregates. Necessary
adjustments are also required to be made in mass of A-14 The slump shall be measured and the water
aggregates. The surface water and percentage water absorption content and dosage of admixture shall be adjusted
of aggregates shall be determined according to IS 2386.
for achieving the required slump based on trial, if
A-11 ADJUSTMENT ON WATER, FINE required. The mix proportions shall be reworked for
AGGREGATE AND COARSE AGGREGATE the actual water content and checked for durability
(IF THE COARSE AND FINE AGGREGATE IS requirements.
IN DRY CONDITION)
A-15 Two more trials having variation of ± 10
a) Fine Aggregate percent of water-cement ratio in A-10 shall be carried
(Dry) out and a graph between three water-cement ratios
Mass of fine aggregate in SSD condition and their
= Water absorption
corresponding strengths shall be plotted to work out
1+ /100 the mix proportions for the given target strength for
648 field trials. However, durability requirement shall be
=
1  1 100 met.
/
= 641.58 kg/m3  642 kg/m3
ANNEX B
(Clause 5.9)
ILLUSTRATIVE EXAMPLE OF MIX PROPORTIONING OF
CONCRETE (USING FLY ASH AS PART REPLACEMENT OF OPC)
B-0 An example illustrating the mix proportioning for a concrete of M40 grade using fly ash is given in B-1
to B-15.
B-1 STIPULATIONS FOR PROPORTIONING

b) Type of cement : OPC 43 grade conforming to IS 269
c) Type of mineral admixture : Fly ash conforming to IS 3812 (Part1)
d) Maximum nominal size of aggregate : 20 mm
e) Minimum cement content and maximum
water-cement ratio to be adopted : Severe(for reinforced concrete)
and/or
Exposure conditions as per Table 3 and Table 5 of IS 456
f) Workability : 120 mm (slump)
g) Method of concrete placing : Pumping
h) Degree of supervision : Good
j) Type of aggregate : Crushed angular aggregate
k) Maximum cement content (OPC content) : As per IS 456
m) Chemical admixture type : Superplasticizer- normal
B-2 TEST DATA FOR MATERIALS
a) Cement used : OPC 43 grade conforming to IS 269
c) Fly ash : Conforming to IS 3812 (Part 1)
d) Specific gravity of fly ash : 2.2
e) Chemical admixture : Superplasticizer conforming to IS 9103
f) Specific gravity of
1) Coarse aggregate (at SSD condition) : 2.74
2) Fine aggregate (at SSD condition) : 2.65
g) Water absorption
h) The coarse and fine aggregates are wet and their total moisture content is 2 percent and 5 percent
respectively. Therefore, the free moisture content in coarse and fine aggregate shall be as shown in (j)
below
j) Free (surface) moisture
1) Coarse aggregate : Free moisture = Total moisture content –
Water absorption
= 2.0 – 0.5 = 1.5 percent
2) Fine aggregate : Free moisture = Total moisture content –
Water absorption
= 5.0 – 1.0 = 4.0 percent
k) Sieve analysis
mm Fraction
I II I II 100
(20-10 mm) (10 - 4.75 mm) 60 percent 40 percent percent
(1) (2) (3) (4) (5) (6) (7)
20 100 100 60 40 100 Conforming
10 Nil 71.20 Nil 28.5 28.5 to Table 7 of
4.75 Nil 9.40 Nil 3.7 3.7 IS 383
2.36 Nil Nil Nil Nil Nil
IS 383
B - 3 TAR GE T S T RE NGT H FOR B-6 SELECTION OF WATER CONTENT

M I X PROPORTIONING
From Table 4, water content = 186 kg (for 50 mm
f’ck = fck + 1.65 S slump) for 20 mm aggregate.
or Estimated water content for 120 mm slump
f’ck = fck + X (increasing at the rate of 3 percent for every 25 mm
whichever is higher. slump)
where
8.4
f’ck = target average compressive strength at = 186  186
28 days, 100
= 201.62 kg
fck = char acter istic co mpr e ssive stre ngth
at As superplasticizer is used, the water content may be
28 days reduced.
S = standard deviation, and Based on trial data, the water content reduction of
X = factor based on grade of concrete. 23 percent is considered while using superplasticizer
at the rate 1.0 percent by weight of cement.
From Table 2, standard deviation, S = 5 N/mm2.
Hence the arrived water content = 201.62 × 0.77 =
From Table 1, X = 6.5 155.25 kg ≈ 155 kg.
Therefore, target strength using both equations, that
is, B-7 CALCULATION OF CEMENT CONTENT
a) f’ck =fck+1.65 S Water-cement ratio = 0.36
= 40 + 1.65 × 5 = 48.25 N/mm2 155
b) f’ck = fck + 6.5
Cement content =
= 40 + 6.5 = 46.5 N/mm2 0.36
The higher value is to be adopted. Therefore, target = 430.55 kg/m3 ≈ 431 kg/m3
strength will be 48.25 N/mm2 as 48.25 N/mm2 > To proportion a mix containing fly ash the following
46.5 N/mm2. steps are suggested:
B-4 APPROXIMATE AIR CONTENT a) Decide the percentage fly ash to be used
From Table 3, the approximate amount of entrapped based on project requirement and quality of
air to be expected in normal (non-air-entrained) fly ash.
concrete is 1.0 percent for 20 mm nominal maximum b) In certain situations, increase in
size of aggregate. cementitious material content may be
B-5 SELECTION OF WATER-CEMENT warranted. T he decision on increase in
RATIO cementitious material content and its
percentage may be based on experience and
trials.
the target strength of 48.25 N/mm2 is 0.36 for OPC
NOTE — This illustrative example is with increase of 10
43 grade curve. This is lower than the maximum percent cementitious material content.
value of
0.45 prescribed for ‘severe’ exposure for reinforced Cementitious material content
concrete as per Table 5 of IS 456. = 431 × 1.10 = 474.1 kg/m3 ≈
474 kg/m3
0.36 < 0.45, hence O.K.
Water content = 155 kg/m3
So, water-cementitious ratio d) Volume of fly ash
155
=  Mass of fly ash 1
0.327 =
474 
Fly ash @ 30 percent of total cementitious Specific gravity of fly ash 1 000
material content = 474 × 30 percent =
142 1
142.2 ≈ = 
142 kg/m3 2.2 1 000
Cement (OPC) = 474 – 142 = 332 kg/m3 = 0.064 5 m3
e) Volume of water
From Table 5 of IS 456, minimum cementitious
content for ‘severe’ exposure condition Mass of water 1
= 
= 320 kg/m3
155 1
474 kg/m3 > 320 kg/m3, hence O.K. = 
1 1 000
B-8 PROPORTION OF VOLUME OF COARSE = 0.155 m3
A GGR EGATE AN D F I N E AG GR A G f) Volume of chemical admixture
ET E CONTENT (superplasticizer) (@ 1.0 percent
From Table 5, volume of coarse aggregate by mass of cementitious material)
corresponding to 20 mm size aggregate and fine
Mass of chemical admixture 1
aggregate (Zone II) for water-cement ratio of 0.50 = = 
0.62. Specific gravity of admixture 1 000
In the present case water-cementitious ratio is 0.327. 4.74 1

Therefore, volume of coarse aggregate is required to = 1.145  1 000
be increased to decrease the fine aggregate content.
As the water-cement ratio is lower by 0.173, the = 0.004 m3
proportion of volume of coarse aggregate is increased g) Volume of all in aggregate
by 0.034 6 (at the rate of  0.01 for every ± 0.05 = [(a-b)-(c+d+e+f)}]
change in water- cement ratio). Therefore, = (1-0.01)-(0.105 + 0.064 5 + 0.155+0.004)
corrected proportion of volume of coarse aggregate = 0.661 5 m3
for the water-cementitious ratio of 0.327 = 0.62 +
h) Mass of coarse aggregate
0.034 6 = 0.654 6.
= g × volume of coarse aggregate × Specific
For pumpable concrete these values may be reduced gravity of coarse aggregate × 1 000
by up to 10 percent. (see 5.5.2). Here, 10 percent = 0.661 5 × 0.59 × 2.74 × 1 000
reduction is considered.
= 1 069.38 kg ≈ 1 069 kg
Therefore, volume of coarse aggregate = 0.654 6 × j) Mass of fine aggregate
0.9 = 0.589 1, say 0.59 m3. = g × Volume of fine aggregate × Specific
Volume of fine aggregate content = 1 – 0.59 = 0.41 gravity of fine aggregate × 1 000
m3 = 0.661 5 × 0.41 × 2.65 × 1 000
= 718.71 ≈ 719 kg
B-9 MIX CALCULATIONS
B - 1 0 M I X P RO P ORT I O NS F O R T
The mix calculations per unit volume of concrete R IAL NUMBER 1
shall be as follows:
Cement = 332 kg/m3
a) Total volume = 1m 3
Fly ash = 142 kg/m3
b) Volume of entrapped air
Water (Net mixing) = 155 kg/m3
in wet concrete = 0.01 m3
Fine aggregate (SSD) = 719 kg/m3
c) Volume of cement 3
Mass of cement 1
= 
Specific gravity of cement 1 000
332 1
= 3.15  1 000 Coarse aggregate (SSD) = 1 069 kg/m
Chemical admixture = 4.74 kg/m3
= 0.105 m3 Free water-cementitious materials ratio
= 0.327
NOTE — Aggregates shall be used in saturated surface dry 2) Wate r con t e nt c ont ri b ute d b y w e t
mixing water, allowance shall be made for the free (surface) f ine aggregate
moisture contributed by the fine and coarse aggregates. On the = Mass of wet fine aggregate – mass of SSD
other hand, if the aggregates are dry, the amount of mixing condition fine aggregate
water shall be increased by an amount equal to the moisture
likely to be absorbed by the aggregates. Necessary = 748 – 719 = 29 kg
adjustments are also required to be made in mass of The requirement for added water becomes :
aggregates. The surface water and percent water absorption
of aggregates shall be determined according to IS 2386 (Part = 155 - 16 - 29
3). = 110 kg/m3
B - 11 ADJ US T M E N T O N WATE R, F B-12 MIX PROPORTIONS AFTER
INE AGGREGATE AND COARSE ADUSTMENT FOR WET AGGREGATES
AGGREGATE (IF THE COARSE AND FINE
Cement = 332 kg/m3
AGGREGATE IS IN WET CONDITION)
Fly ash = 142 kg/m3
a) Fine aggregate (Wet) Water (to be added) = 110 kg/m3
Mass of wet fine aggregate Fine aggregate (Wet) = 748 kg/m3
= mass of fine aggregate in SSD condition × Coarse aggregate (Wet) = 1 085 kg/m3
 Free (surface) moisture  Chemical admixture = 4.74 kg/m3
1  
 100  Free water-cementitious materials ratio
= 719 × (1+4/100) = 0.327
= 747.76 kg/m3 ≈ 748 kg/m3
B-13 The total mass of coarse aggregate shall be
b) Coarse aggregate (Wet)
divided into two fractions of 20 – 10 mm and 10 –
Mass of wet coarse aggregate 4.75 mm, in a suitable ratio, to satisfy the overall
= mass of coarse aggregate in SSD grading requirements for 20 mm max size aggregate
condition as
 Free (surface) moisture  per Table 7 of IS 383. In this example, the ratio works
× 1  
 100  out to be 60:40 as shown under B-2 (k).
= 1 069 × (1+1.5/100)
B-14 The slump shall be measured and the water
= 1 085.03 kg/m3 ≈ 1 085kg/m3
content and dosage of admixture shall be adjusted for
The coarse and fine aggregates, being wet, contribute achieving the required slump based on trial, if
water to the mix to the extent of free moisture over required. The mix proportions shall be reworked for
SSD condition. The quantity of this water is required the actual water content and checked for durability
to be subtracted from the calculated water content. requirements.
1) Water content contributed by wet coarse B-15 Two more trials having variation of ± 10
aggregate percent of water-cementitious materials ratio in B-10
= Mass of wet coarse aggregate – mass of shall be c ar r ie d o ut an d a gr ap h b et wee n t
SSD hes e wa t er- cementitious materials ratios and their
condition coarse aggregate corresponding stre ngths sha ll b e plo tted to wo
= 1 085 – 1 069 = 16 kg r k out the mix proportions for the given target
strength for field trials. However, durability
requirement shall be met.
ANNEX C
(Clause 5.9)
ILLUSTRATIVE EXAMPLE OF MIX PROPORTIONING OF
CONCRETE (USING GGBS AS PART REPLACEMENT OF OPC)
C-0 An example illustrating the mix proportioning for a concrete of M40 grade using GGBS is given in C-1
to C-11.
C-1 STIPULATIONS FOR PROPORTIONING

c) Type of mineral admixture : GGBS conforming to IS 16714
d) Maximum nominal size of aggregate : 20mm
water-cement ratio to be adopted and/or
Exposure condition as per Table 3 and Table 5
of IS 456 : Severe (for reinforced concrete)
j) Type of aggregate : Crushed stone angular aggregate
k) Maximum cement (OPC content) : As per IS 456
m) Chemical admixture type : Super plasticizer- normal
C-2 TEST DATA FOR MATERIALS
c) GGBS : Conforming to IS 16714
d) Specific gravity of GGBS : 3
e) Chemical admixture : Super plasticizer conforming to IS 9103
f) Specific gravity (at SSD condition) of
1) Coarse aggregate : 2.74 (based on saturated surface dry condition)
2) Fine aggregate : 2.65 (based on saturated surface dry condition)
3) Chemical Admixture : 1.145
g) Water absorption
h) Moisture content of aggregate [As per
IS 2386(Part 3)]
j) Sieve analysis
1) Coarse aggregate:
mm Fraction
I II I II 100
(1) (2) (3) (4) (5) (6) (7)
20 100 100 60 40 100 Conforming
10 Nil 71.20 Nil 28.5 28.5 to Table 7 of
4.75 Nil 9.40 Nil 3.7 3.7 IS 383
2.36 Nil Nil Nil Nil Nil
2) Fine aggregate : Conforming to grading Zone II of Table 9 of IS
383
C - 3 TAR GET S TREN GTH FOR M the rate of 1.0 percent by weight of cement.
I X PROPORTIONING
f’ck = fck + 1.65 S
or
f’ck = fck + X
whichever is higher
where
f’ck = target average compressive strength at
28 days,
fck = char acter istic co mpr e ssive stre ngth
at
28 days,
S = standard deviation, and
from Table 2, standard deviation S = 5 N/mm2
From Table 1, X = 6.5.
Therefore, target strength using both equations, that
is, a) f’ck = fck +1.65 S
= 40 + 1.65 x 5 = 48.25 N/mm2
b) f’ck = fck + 6.5
= 40 + 6.5 = 46.5 N/mm2
The higher value is to be adopted. Therefore, target
strength will be 48.25 N/mm2 as 48.25 N/mm2 >
46.5 N/mm2.
C-4 APPROXIMATE AIR CONTENT
concrete is 1.0 percent for 20 mm nominal maximum
size of aggregate.
C-5 SELECTION OF WATER-CEMENT
RATIO
From Fig. 1 the free water-cement ratio required for
43 grade curve. This is lower than the maximum
value of
0.45 prescribed for ‘severe’ exposure for reinforced
concrete as per Table 5 of IS 456.
0.36 < 0.45, hence O.K.
C-6 SELECTION OF WATER
CONTENT
From Table 4, water content
= 186 kg (for 50 mm slump) for 20 mm
aggregate. Estimated water content for 120 mm
slump (increasing
at the rate of 3 percent for every 25 mm slump)
84
= 186  186
100
= 201.62 kg
As super plasticizer is used, the water content may be
reduced.
Based on trial data, the water content reduction of 23
percent is considered while using super plasticizer at
Hence the arrived water content
= 201.62 × 0.77
= 155.25kg ≈ 155 kg
C-7 CALCULATION OF CEMENT CONTENT
Cement content = 155/0.36
= 430.55 kg/m3 ≈ 431 kg/m3
From Table 5 of IS 456, minimum cement content for
‘severe’ exposure condition
= 320 kg/m3
431 kg/m > 320 kg/m3, hence O.K.
3
To proportion a mix containing GGBS the following

steps are suggested:
a) Decide the percentage of GGBS to be used
based on project requirement and quality of
GGBS.
b) In certain situations increase in cementitious
material content may be warranted. T he
decision on increase in cementitious material
content and its percentage may be based on
experience and trials.
GGBS @ 40 percent of total cementitious material
content
= 431 × 40 percent
= 172.4 ≈ 172 kg/m3
Cement (OPC) = 431 – 172 = 259 kg/m3
C-8 PROPORTION OF VOLUME OF COARSE
A GGR E GAT E A N D F I NE A GG RE
GAT E CONTENT
From Table 5, volume of coarse aggregate
corresponding to 20 mm size aggregate and fine
aggregate (Zone II) for water-cement ratio of 0.50 =
0.62.
In the present case water-cementitious ratio is 0.36.
Therefore, volume of coarse aggregate is required to
be increased to decrease the fine aggregate content.
As the water-cement ratio is lower by 0.14, the
proportion of volume of coarse aggregate is
increased by 0.028 (at the rate of  0.01m3 for
every ± 0.05 change in water-cement ratio).
Therefore, corrected volume of coarse aggregate for
the water-cementitious ratio of
0.36 = 0.62 + 0.028 = 0.648 m3.
For pumpable concrete these values may be reduced
by up to 10 percent. (see 5.5.2). Here, 10 percent
reduction is considered.
Therefore, volume of coarse aggregate
= 0. 648 × 0.9
= 0.583 2 say 0.58 m3
Volume of fine aggregate content g) Volume of total aggregate
= 1 – 0.58 = 0.42 m 3 = [(a-b)-(c+d+e+f)]
= (1-0.01) - (0.0 822+0.0 573+0.155+0.0 038)
C-9 MIX CALCULATION
= 0.691 7 m3
The mix calculation per unit volume of concrete shall h) Mass of coarse aggregate
be as follows:
= g × Volume of coarse aggregate ×
a) Total Volume = 1 m3 Specific gravity of coarse aggregate × 1
b) Volume of entrapped air in wet concrete 000
= 0.01 m3 = 0.6 917 × 0.58 × 2.74 × 1 000
c) Volume of cement = 1 099 kg
j) Mass of fine aggregate
Mass of cement 1
=  = g × Volume of fine aggregate × Specific
259 1 = 0.6 971 × 0.42 × 2.65 × 1 000
= 
3.15 1 000 = 769.86 ≈ 770 kg
= 0.082 2 m3 C - 1 0 M I X P RO P O RT I O NS FOR T
d) Volume of GGBS R IAL NUMBER 1
Mass of GGBS 1 Cement = 259 kg/m3
= 
Specific gravity of GGBS 1 000 GGBS = 172 kg/m3
172 1 Water (Net mixing) = 155 kg/m3
= 3  1 000 Fine aggregate (SSD) = 770 kg/m3
Coarse aggregate (SSD) = 1 099 kg/m3
= 0.057 3 m3
Chemical admixture = 4.31 kg/m3
e) Volume of water
Free water-cementitious material ratio
Mass of water  1 = 0.36
=
Specific gravity of water 1 000 NOTE — Aggregates shall be used in saturated surface dry
155 1 mixing water, allowance shall be made for the free (surface)
= 1  1 000 moisture contributed by the fine and coarse aggregates. On the
other hand, if the aggregates are dry, the amount of mixing
= 0.155 m3 water shall be increased by an amount equal to the moisture
likely to be absorbed by the aggregates. Necessary adjustments
f) Volume of chemical admixture are also required to be made in mass of aggregates. The
(super plasticizer) @1.0 percent surface water and percent water absorption of aggregates
shall be determined according to IS 2386 (Part 3).
by mass of cementitious material)
Mass of chemical admixture 1 C - 11 ADJ US T M E N T O N WATE R , F
=  INE AGGREGATE AND COARSE
Specific gravity of admixture 1 000
AGGREGATE (IF THE COARSE AND FINE
4.31 1 AGGREGATE IS IN DRY CONDITION)
= 
1.145 1 000 As the coarse and fine aggregates are in dry
= 0.003 8 m3 condition, adj ustme nt of water, fine aggr ega te
and c oar se aggregate shall be done as given in A-
11.
ANNEX D
(Clause 6.4)
ILLUSTRATIVE EXAMPLE ON CONCRETE MIX PROPORTIONING
FOR HIGH STRENGTH CONCRETE
D-0 An example illustrating the mix proportioning advantageous for grades of concrete M50 and above
for a concrete of M70 grade using silica fume and fly and for high performance concrete with special
ash is gi ven belo w. U se o f si lica fume is requirements, like higher abrasion resistance of
gener al ly concrete.
D-1 STIPULATIONS FOR PROPORTIONING

a) Grade designation : M 70
c) Silica fume : Conforming to IS 15388
e) Exposure conditions as per Table 3
and Table 5 of IS 456 : Severe (for reinforced concrete)
j) Type of aggregate : Crushed angular aggregate
k) Maximum cement (OPC) content : 450 kg/m3
m) Chemical admixture type : Superplasticizer (Polycarboxylate ether based)
D-2 TEST DATA FOR MATERIALS
a) Cement used : OPC 53 Grade conforming to IS 269
c) Specific gravity of
3) Fly ash : 2.20
4) Silica fume : 2.20
d) Water absorption
f) Moisture content
g) Sieve analysis
IS Sieve Sizes Analysis of Aggregate Percentage of Different Fractions Remarks
mm Fraction
I I I II 100
(20-10 mm) (10-4.75 mm) 50 50 Percent
Percent Percent
(1) (2) (3) (4) (5) (6) (7)
20 100 100 50 50 100 Conforming
10 2.8 78.3 1.4 39.15 40.55 to Table 7 of
4.75 Nil 8.70 Nil 4.35 4.35 IS 383
2) Fine aggregate : Conforming to grading Zone II of Table 9 of IS

383
D - 3 TAR GET S TREN GTH FOR M D-7 CALCULATION OF CEMENT
I X PROPORTIONING CONTENT
f’ck = fck+1.65 S Water–cement ratio = 0.29
or Water content = 141 kg/m3
f’ck = fck + X Cement content = 141 / 0.29
whichever is higher. = 486.2 ≈ 486 kg/m3
where It is proposed to add 15 percent fly ash in the mix, in
such situations increase in cementitious material
f’ck = target average compressive strength at content may be war ranted . T he d ecisio n on
28 days, increase in cementitious material content and its
fck = char acter istic co mpr e ssive stre ngth percentage may be based on experience and trial.
at NOTE — This illustrative example is with an increase of 10
28 days, percent cementitious material content.
S = standard deviation, and The cementitious material content

X = factor based on grade of concrete. = 486 × 1.10
From Table 2, standard deviation, S = 6.0 N/mm . 2 = 534.6 ≈ 535 kg/m3
Fly ash @ 15 percent by weight of cementitious
Therefore, target strength using both equations, that material
is, = 535 × 15 percent
a) f’ck = fck+1.65 S = 80.25 kg/m3
= 70 +1.65 × 6.0 = 79.9 N/mm2 Silica fume content @ 5 percent by weight of revised
b) f’ck = fck + 8.0 (The value of X for M 70 cementitious material
grade as per Table 1 is 8.0 N/mm2) = 535 × 5 percent
= 70 + 8.0 = 78.0 N/mm2 = 26.75 kg/m3
The higher value is to be adopted. Therefore, target Cement content = 535 – 26.75 – 80.25
strength will be 79.9 N/mm2 as 79.9 N/mm2 > 78.0 = 428 kg/m3
N/mm2. 141
D-4 APPROXIMATE AIR CONTENT
From Table 6, the approximate amount of entrapped Revised w/cm = = 0.264
535
air to be expected in normal (non-air-entrained) = 202 × 0.70
concrete is 0.5 percent for 20.0 mm nominal = 141.4 kg/m3 ≈ 141
maximum size of aggregate. kg/m3
D-5 SELECTION OF WATER-CEMENTIOUS
MATERIALS RATIO
From Table 8, the water-cementitious materials ratio
required for the target strength of 79.9 N/mm2 is 0.29
for msa 20 mm. This is lower than the maximum value
of 0.45.
0.29< 0.45, hence O.K.
D-6 SELECTION OF WATER

CONTENT
From Table 7, water content for 20 mm
aggregate
= 186 kg/m3 (for 50 mm slump without using
superplasticiser).
Estimated water content for 120 mm slump
8.4
= 186  186
100
= 201.624 ≈ 202 kg/m3
As superplasticizer (Polycarboxylate ether based) is
used, the water content can be reduced by 30 percent.
Hence, the reduced water content
Check for minimum cementitious materials content,
320 kg/m3 < 535 kg/m3 (428 kg/m3 OPC + 26.75
kg/m3
silica fume + 80.25 kg/m3 fly ash) Hence OK
Check for maximum cement(OPC) content, 450
kg/m3
> 428 kg/m3. Hence OK.
D-8 PROPORTION OF VOLUME OF COARSE
A GGR E GAT E A N D F I NE A GG RE
GAT E CONTENT
F r o m Tab l e 1 0 , v ol u me o f coar se ag g r
ega t e corresponding to 20 mm size aggregate and
fine aggregate grading Zone II = 0.66 per unit
volume of total aggregate. This is valid for water-
cementitious materials ratio of 0.30. As water-
cementitious material ratio is actually 0.264, the ratio
is taken as 0.667.
Volume of fine aggregate
content
= 1 – 0.667
= 0.333 per unit volume of total aggregate
D-9 MIX CALCULATIONS
a) Total volume = 1 m3
b) Volume of entrapped air = 0.005 m3
in wet concrete
c) Volume of cement = 0.667 × 0.667 × 2.74 × 1 000
Mass of cement 1 = 1 218.9 kg ≈ 1 219 kg
= 
Specific gravity of cement 1 000 k) Mass of fine aggregate
428 1 = h × volume of fine aggregate × Specific
= 3.15  1 000 gravity of fine aggregate × 1 000
= 0.667 × 0.333 × 2.65 × 1 000
= 0.136 m3
= 588.59 kg ≈ 589 kg
d) Volume of water
D - 9 . 1 M I X P RO P O RTI O NS F O R T
Mass of water 1
=  R IAL N UM B ER 1 O N A GG R EG ATE
Specific gravity of water 1 000 IN SS D CONDITION
141 1
=  Cement = 428 kg/m3
1 1 000
Fly ash = 80.25 kg
= 0.141 m3 Silica fume = 26.75kg/m3
e) Volume of silica fume Water = 141 kg/m3
Fine aggregate = 589 kg/m3
Mass of silica fume 1
=  Coarse aggregate = 1 219 kg/m3
Specific gravity of silica fume 1 000 Chemical admixture = 2.67 kg/m3
26.75 1
=  w/cm = 0.264
2.2 1 000
NOTE — Aggregates shall be used in saturated surface dry
= 0.012 2 m3 condition. If otherwise, when computing the requirement of
f) Volume of fly ash mixing water, allowance shall be made for the free (surface)
moisture contributed by the fine and coarse aggregates. On the
other hand, if the aggregates are dry, the amount of mixing
Mass of fly ash 1
=  water shall be increased by an amount equal to the moisture
Specific gravity of fly ash 1 likely to be absorbed by the aggregates. Necessary adjustments
are also required to be made in mass of aggregates. The
000 surface water and percent water absorption of aggregates
shall be
= 80.25  1 determined according to IS 2386 (Part 3).
2.2 1 000
= 0.036 5 m3 D-10 The total mass of coarse aggregate shall be
g) Vo lu me of c he mic a l ad divided into two fractions of 20 - 10 mm and 10 -
mixtur e (superplasticizer) (@ 0.5 percent 4.75 mm, in a suitable ratio, to satisfy the overall
by mass of cementitious material) grading requirements for 20 mm max size aggregate
Mass of chemical admixture 1 as per Table 7 of IS 383. In this example, the ratio
=  works out to be 50:50 as shown under D-2 (g).
Specific gravity of admixture 1 000
(535 0.5%) 1 D-11 The slump shall be measured and the water
=  content and dosage of admixture shall be adjusted for
1.08 1 000 achieving the required slump based on trial, if
= 0.002 5 m3 required. The mix proportions shall be reworked for
h) Volume of all in aggregate the actual water content and checked for durability
= [(a-b)-(c+d+e+ f+g)] requirements.
= [(1-0.005) – (0.136 + 0.141 + 0.012 2 + D-12 Two more trials having variation of ±10 percent
0.036 5 + 0.002 5)] of water-cementitious materials ratio in D-9.1 shall
= 0.66 7 m3 be c ar r ie d o ut an d a gr ap h b et wee n t hes e
j) Mass of coarse aggregate wa t er- cementitious materials ratios and their
= h × Volume of coarse aggregate × corresponding stre ngths sha ll b e plo tted to wo
Specific gravity of coarse aggregate × 1 r k out the mix proportions for the given target
000 strength for field trials. However, durability
requirement shall be met.
ANNEX E
(Clause 8.4)
ILLUSTRATIVE EXAMPLE ON CONCRETE MIX PROPORTIONING FOR SCC
E-0 An example illustrating the mix proportioning procedure for SCC concrete is given in E-1 to E-13.
E- 1 STIPULATIONS FOR PROPORTIONING
c) Nominal maximum size of aggregate : 20 mm
d) Exposure conditions as per Table 3
and Table 5 of IS 456 : Severe (for reinforced concrete)
e) Characteristics of SCC
1) Slump flow class : SF3 (slump flow 760 mm – 850 mm)
2) Passing ability by L box test : Ratio of h2/h1 = 0.9
3) V- Funnel flow time (Viscosity) : Class V1 (flow time ≤ 8s)
4) Sieve segregation resistance : SR1(15percent)
f) Degree of site control : Good
g) Type of aggregate : Crushed angular aggregate
h) Maximum cement content (OPC Content) : 450 kg/m3
j) Chemical admixtures type
1) Superplasticizer : normal (PCE type)
2) Viscosity modifying agent
k) Mineral admixture : Fly ash conforming to IS 3812 (Part 1)
E-2 TEST DATA FOR MATERIALS
a) Cement used : OPC 43 Grade conforming to IS 269
c) Chemical admixture : Superplasticizer conforming to IS 9103
d) Specific gravity of
e) Water absorption
f) Free (surface) moisture
1) Coarse aggregate : Nil (absorbed moisture also nil)
2) Fine aggregate : Nil (absorbed moisture also nil)
g) Sieve analysis
1) Coarse aggregate:
mm Fraction
I II I II 100
(1) (2) (3) (4) (5) (6) (7)
20 100 100 50 50 100 Conforming
10 2.8 78.3 1.4 39.15 40.55 of Table 7 of
4.75 Nil 8.70 Nil 4.35 4.35 IS 383
2) Fine aggregate : Conforming to grading Zone II of Table 9 of IS 383
(materials less than 0.125 mm is 8 percent, based on
sieve analysis)
E-3 TARGET STRENGTH FOR MIX as per IS 1199 (Part 6) and adjustments to the initial
PROPORTIONING mix shall be made till satisfactory characteristics are
f’ck = fck+1.65 S achieved.
The various mix design parameters given in this
or
example are only indicative and it may be necessary
f’ck = fck + X to carry out adjustments to these parameters during
the use of the concrete mix at the project site.
whichever is higher.
where E-7 PROPORTIONING FOR INITIAL MIX
f’ck = target average compressive strength at E-7.1 Selection of Water Content and Cement/Fly
28 days, Ash Content
fck = characteristic compressive strength at The class of slump flow is specified to be SF3 having
28 days, a slump flow between 750 and 850 mm. To start
S = standard deviation, and with, a water content of 190 kg/m3 along with a
superplasticizer
X = factor based on grade of concrete. @ 0.6 percent by mass of cementitious material
From Table 2, standard deviation, S = 5 N/mm2. content is selected for the initial mix. However, the
water content can be reduced further by increasing
From Table 1, X = 6.5. the dose of super plasticizer.
Therefore, target strength using both equations, that This water content of 190 kg/m3 will correspond to a
is cement content of 442 kg/m3 for water cement ratio
a) f’ck = fck+1.65 S of
= 30 + 1.65 × 5 = 38.25 N/mm2 0.43 as worked out in E-5.
b) f’ck = fck + 6.5 The cement content of 442 kg/m3 can be further
= 30 + 6.5 = 36.5 N/mm2 divided into OPC and fly ash. Generally fly ash
content of 25 to
50 percent is adopted for SCC. In this illustration, as
strength will be 38.25 N/mm2 as 38.25 N/mm2 > 36.5
the cement content is on the higher side, the fly ash
N/mm2.
content is taken as 35 percent. Therefore, the OPC
E-4 APPROXIMATE AIR CONTENT content is for
287 kg/m3 and fly ash content will be 155
From Table 3, the approximate amount of entrapped kg/m 3.
concrete is 1.0 percent for 20 mm nominal maximum E-7.2 Selection of Admixture Content
size of aggregate. Taking an admixture dose of 0.6 percent by mass of
E-5 SELECTION OF WATER-CEMENT cementitious material, the mass of admixture
RATIO = 0.6/100 × 442 = 2.65 kg/m3.
E-7.3 Selection of Powder Content and Fine
Aggregate Content
43 grade curve. This is lower than the maximum
value of The powder content (fines < 0.125 mm) required for
0.45 prescribed for ‘severe’ exposure for reinforced SCC is generally in the range of 400 to 600 kg/m3.
concrete as per Table 5 of IS 456. Since, the SR of class 1 and viscosity of V1 is
required; the mix shall be sufficiently cohesive,
0.43< 0.45, hence O.K.
(having enough fines). Therefore a powder content
E-6 The initial mix shall be first estimated based on of 520 kg/m3 is selected. This powder content will
the typical ranges of mix constituents as per 8.3 and constitute the entire OPC, entire fly ash, and around
keeping in view, the characteristics of the fresh 10 percent of Zone II fine aggregates.
concrete such as flowability, passing ability,
Fines required to be contributed by fine aggregate =
segregation resistance and viscosity as per the data
Total powder content – (Fly ash content + cement
for the mix proportioning in E-1.
content)
The initial mix shall be tested for various
characteristics = 520 – (155 + 287) = 78 kg/m3
The fine aggregate has 8 percent materials < 0.125
mm
(see 8.1). Therefore, the fine aggregate quantity =
78/0.08 = 975 kg/m3.
E-7.4 Selection of Coarse Aggregate Content NOTE — Aggregates shall be used in saturated surface dry
Let Vca be the volume of coarse aggregate. mixing water, allowance shall be made for the free (surface)
Assuming 1 m3 of concrete, Vca = (1 - Air content) other hand, if the aggregates are dry, the amount of mixing
- (Vol of water + Vol of cement + Vol of fly ash + water shall be increased by an amount equal to the moisture
Vol of admixture + Volume of fine aggregate) likely to be absorbed by the aggregates. Necessary adjustments
are also required to be made in mass of aggregates. The
surface water and percent water absorption of aggregates
190  287  155
Vca = (1- 0.01) – shall be determined according to IS 2386 (Part 3).
11 000 3.15 1 000 2.2 1 000
 E-9 The total mass of coarse aggregate shall be
divided into two fractions of 20 - 10 mm and 10 -
2.65 975 4.75 mm, in a s uita b le r a ti o , to sa t isfy the o

1.08 1 000 2.65 1 ve r a ll gr a d ing requirements for 20 mm max size
000 aggregate as per Table 7 of IS 383. In this example,
= 0.99 – (0.19 + 0.091 + 0.07 + 0.002 5 + 0.368) the ratio works out to be 50:50 as shown under E-2
(g).
= 0.269 m3
E-10 The various tests for flowability (slump flow
Mass of coarse aggregate test), for passing ability (L box test), for sieve
segregation resistance and for viscosity (V funnel)
= Vca x specific gravity of coarse aggregate × 1 000
shall be carried out and the values obtained shall be
= 0.268 × 2.74 × 1 000 verified as per the data given in E.1 (e).
= 737.06 kg/m3 ≈ 737 kg/m3
In the event that satisfactory performance is not
E-7.5 Calculation of Volume of Powder obtained, the initial mix shall be redesigned.
Content Depending on the apparent problem, the following
Vol of powder content = Vol of OPC + Vol of fly ash courses of action might be appropriate:
+ Vol of portion of fine aggregate < 0.125 mm a) Adjust the cement/powder ratio and the
287 water/ powder ratio and test the flow and
=  155  78 other properties of the paste.
3.15 1 000 2.2 1 000 2.65 1
b) Try higher doses of fly ash and/or different
000 types of additives (if available).
= 0.191 m3 c) Adjust the proportions of the fine aggregate
and the dosage of superplasticiser.
Ratio of water to powder by volume
d) Consider using a viscosity modifying agent
= 0.190/ 0.191 = 0.99 to reduce sensitivity of the mix.
NOTE — The water to powder ratio is expected to be between e) Adjust the proportion or grading of the
0.85 and 1.10. In this case, it is ok. If water to powder ratio is coarse aggregate.
found to be less than 0.85, then the fine aggregate content
shall be reduced to increase the ratio; if the ratio is more than In the present case, based on trials the need was felt
1.1, then the fine aggregate content shall be increased to to use a small dose (0.2 percent by weight of
decrease the ratio. In such cases, all the values shall be
cementitious materials) of viscosity modifying agent
recalculated.
to improve sensitivity of the mix, that is, improve the
E -8 M IX PR OPORTI ON S FOR TR cohesiveness of the mix.
IA L NUMBER 1 E-11 Two more trials having variation of ± 10
Cement = 287 kg/m3 percent of water-cement ratio in E-10 shall be carried
Flyash = 155 kg/m3 out and a graph between three water-cement ratios
and their corresponding strengths shall be plotted to
Water (net mixing) = 190 kg/m3
work out the mix proportions for the given target
Fine aggregate (SSD ) = 975 kg/m3 strength for field trials. However, durability
Coarse aggregate (SSD) = 737 kg/m3 requirement shall be met.
Chemical admixture = 2.65 kg/m3,
Free water-cement ratio = 0.43
Powder content = 520 kg/m3
Water powder ratio by volume = 0.99
ANNEX F
(Clause 9.12)
ILLUSTRATIVE EXAMPLE ON CONCRETE MIX PROPORTIONING FOR MASS
CONCRETING F-0 An example illustrating the mix proportioning procedure for mass concreting is given in
F-1 to F-14.
F-1 STIPULATIONS FOR PROPORTIONING
c) Type of mineral admixture : Fly ash conforming to IS 3812 (Part1)
water-cement ratio to be adopted and/or : Moderate (for plain concrete)
Exposure conditions as per Table 3 and Table 5
of IS 456
g) Degree of supervision : Good
h) Type of aggregate : Rounded aggregate
j) Maximum cement (OPC) content : 450 kg/m3
k) Chemical admixture : Not required as rounded aggregate of 150 mm
msa is being used
F-2 TEST DATA FOR MATERIALS
c) Fly ash : Conforming to IS 3812 (Part 1)
d) Specific gravity of fly ash : 2.2
e) Specific gravity of
1) Coarse aggregate(at SSD condition) : 2.74
2) Fine aggregate(at SSD condition) : 2.65
f) Water absorption
g) Free (surface) moisture
1) Coarse aggregate : Nil (absorbed moisture also nil)
2) Fine aggregate : Nil (absorbed moisture also nil)
h) Sieve analysis
Sieve Size Percentage Passing
mm
Fraction I Fraction II Fraction III Fraction IV Fraction V
150-80 mm 80-40 mm 40-20 mm 20-10 mm 10-4.75 mm
(1) (2) (3) (4) (5) (6)
150 100 100 100 100 100
80 Nil 92 100 100 100
40 Nil 5 90 100 100
20 – Nil 4 97 100
10 – – Nil 10 78
4.75 – – – 2 10
IS 383
F - 3 TAR GET S TREN GTH FOR M F-7 CALCULATION OF CEMENT CONTENT
I X PROPORTIONING
f’ck = fck+1.65 S
115
or Cement content =
0.6
f’ck = fck + X
whichever is higher. = 191.67 kg/m3
≈ 192 kg/m3
where
To proportion a mix containing fly ash the following
f’ck = target a verage comp ressive str ength
steps are suggested:
at
28 days, a) Decide the percentage fly ash to be used
fck = chara cteristic compr essi ve str eng th based on project requirement and quality of
at fly ash.
28 days, b) In certain situations increase in
S = standard deviation, and cementitious material content may be
X = factor based on grade of concrete. warranted. The decision on increase in
cementitious material content and its
From Table 2, standard deviation, S = 3.5 N/mm2. percentage may be based on experience and
From Table 1, X = 5. trial.
Therefore, target strength using both equations, that NOTE — This illustrative example is with increase of 15
is, percent cementitious material content.
a) f’ck = fck+1.65 S Cementitious material content

= 15 + 1.65 × 3.5 = 20.77 N/mm2 = 192 × 1.15
b) f’ck = fck + 5 = 220.8 kg/m3
= 15 + 5 = 20 N/mm2
≈ 221 kg/m3
Water content = 115 kg/m3
strength will be 20.77 N/mm2 as 20.77 N/mm2 >
So, water-cementitious materials ratio
20 N/mm2.
115
Increase in target strength due to wet sieving through =  0.52
221
40 mm size sieve, as per 9.2 = 25 percent
Fly ash @ 25 percent of total cementitious
T he re for e, fina l targe t str ength = 20 .7 7 × 1 material content
.2 5
= 221 × 25 percent
= 26.0 N/mm2.
= 55 kg/m3
NOTE — This increase in target strength due to wet sieving
effect is only for cube test results and not to be considered for Cement (OPC) = 221 – 55
selection of water cement ratio. = 166 kg/m3
F-4 APPROXIMATE AIR CONTENT From Table 5 and Table 6 of IS 456, minimum
cement content for ‘moderate’ exposure condition
concrete is 0.2 percent for 150 mm nominal = 240 – 30 kg/m3
maximum size of aggregate. = 210 kg/m3
F-5 SELECTION OF WATER-CEMENT RATIO [considering the maximum (40 mm) msa correction
From Fig. 1, the free water-cement ratio required for in Table 6 of IS 456, the value in Table 5 of IS 456
the target strength of 20.77 N/mm2 is 0.61 for OPC 43 has been adjusted]
grade curve. This is higher than the maximum value
of
0.6 prescribed for ‘moderate’ exposure for plain
concrete as per Table 5 of IS 456.
3 3
0.61 > 0.6, hence adopt 0.6. = 125 - 10 = 115
kg
F-6 SELECTION OF WATER CONTENT
From Table 12, water content
= 125 kg (for 50 mm slump) for 150 mm aggregate.
As rounded aggregate is used, the water content may
be reduced by 10 kg as per 9.4,
Hence the reduced water content
221 kg/m >210 kg/m , hence, O.K.
F-8 PROPORTION OF VOLUME OF COARSE

A GGR E GAT E A N D F IN E A GG RE GE
T E CONTENT
F r o m Ta bl e 1 3 , vol ume o f c oa r se a ggr e
ga t e corresponding to 150 mm size aggregate and
fine aggr egate ( Zo ne I I) fo r water-c ement r
at io o f
0.50 = 0.78.
In the present case water-cementitious ratio is 0.52. f) Volume of all in aggregate
Therefore, volume of coarse aggregate is required to = [(a - b) - (c + d +
be increased to decrease the fine aggregate content. e)]
As the water-cement ratio is increased by 0.02, the = (1 - 0.002) – (0.052 7 + 0.025 + 0.115)
proportion of volume of coarse aggregate is
= 0.805 3 m3
decreased by 0.004 (at the rate of  0.01 for every ±
0.05 change in water-cement ratio). g) Mass of coarse aggregate
= f × volume of coarse aggregate × specific
Therefore, corrected proportion of volume of coarse
gravity of coarse aggregate × 1 000
a gg r e g a te fo r th e wa te r- c e me ntitio u s r
a tio o f = 0.805 3 × 0.776 × 2.74 × 1 000
0.52 = 0.78 – 0.004 = 0.776. = 1 712.26 kg ≈ 1 712 kg
h) Mass of fine aggregate
Volume of fine aggregate content = 1 – 0.776 =
0.224 = g × volume of fine aggregate × specific
F-9 MIX CALCULATIONS = 0.805 3 × 0.224 ×2.65 × 1 000
The mix calculations per unit volume of concrete = 478.02 ≈ 478 kg
shall be as follows: F-10 CHECK ON MORTAR CONTENT
a) Total volume = 1m 3
Mortar content, Mc = Vc + Vf + Vw + Vfa+ Va
b) Volume of entrapped air
in wet concrete = 0.002 m3 where
c) Volume of cement Mc = mortar content;
Mass of cement  1
= Vc = volume of cement = 0.0527 m3
166 1 Vf = volume of fly ash = 0.025 m3
= 3.15  1 000 Vw = volume of water = 0.115 m3
= 0.0 52 7 m3 Vfa = volume of fine aggregate = 0.180m3
d) Volume of fly ash Va = volume of air = 0.002 m3
Mass of fly ash 1 So, Mc = 0.375 kg/m3
= 
Specific gravity of fly ash 1 000
The volume of mortar content satisfies the
55 1 requirement of 0.37 ± 0.01 for rounded aggregates
= 
2.2 1 000 for 150 mm msa (see Table 15).
= 0.025 m3 F - 11 M I X P RO P O RT I O NS FOR T
e) Volume of water R IAL NUMBER 1
Mass of water 1
=  Cement = 166 kg/m3
Fly ash = 55 kg/m3
115 1 Water (Net mixing) = 115 kg/m3
= 
1 1 000 Fine aggregate (SSD) = 478 kg/m3
= 0.115 m3 Coarse aggregate (SSD) = 1 712 kg/m3
Sieve Percentage Passing Percentage of Different Combined Combined

Size Fractions Grading Grading
mm Obtained Requirement
Fraction Fraction Fraction Fraction Fraction I II III IV V
I II III IV V
150-80 80-40 40-20 20-10 10-4.75 35% 30% 15% 10% 10% 100%
mm mm mm mm mm
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13)
150 100 100 100 100 100 35 30 15 10 10 100 100
80 0 92 100 100 100 0 27.6 15 10 10 62.6 55 to 65
40 0 5 90 100 100 0 1.5 13.5 10 10 35 29 to 40
20 0 0 4 97 100 0 0 0.6 9.7 10 20.3 14 to 22
10 0 0 0 10 78 0 0 0 1 7.8 8.8 6 to 10
4.75 0 0 0 2 10 0 0 0 0.2 1 1.2 0 to 5
Free water-cementitious materials ratio to the moisture likely to be absorbed by the aggregates.
Necessary adjustments are also required to be made in mass of
= 0.52
aggregates. The surface water and percent water absorption of
F-12 The total mass of coarse aggregate shall be aggregates shall be determined according to IS 2386 (Part 3).
divided into five fractions of 150/80 mm, 80/40 mm, F-13 The slump shall be measured and the water
40/20 mm, content shall be adjusted for achieving the required
20/10 mm, and 10/4.75 mm, in a suitable ratio, to slump based on trial, if required. The mix
satisfy the overall grading requirements for 150 mm proportions shall be reworked for the actual water
max size aggregate as per Table 14. In this example, content and checked for durability requirements.
based on various adjustments the ratio works F-14 Two more trials having variation of ±10 percent
out to be of water-cementitious materials ratio in F-11 shall
35:30:15:10:10 as shown below, to meet the combined be carried out and a graph between these
grading requirements for 150 mm msa as given in water - cementitious materials ratios and their
Table 14. corresponding strengths shall be plotted to work
NOTE — Aggregates shall be used in saturated surface dry out the mix proportions for the given target strength
condition. If otherwise, when computing the requirement of for field trials. However, durability requirement shall
mixing water, allowance shall be made for the free (surface)
be met.
other hand, if the aggregates are dry, as is the present case, the
amount of mixing water shall be increased by an amount equal
ANNEX G
(Informative) (Foreword, Clauses
5.3 and 6.2.4)
GUIDELINES FOR SELECTION OF APPROPRIATE WATER REDUCING
ADMIXTURES
G-1 Cement particles have a strong tendency to plasticising or

flocculate when they come in contact with water.
Even atmospheric moisture is sufficient to result
in flocculation of cement. The flocculation of
cement results in the formation of a network of
cement particles which trap part of mix water in the
network voids. The water which is held by cement
particles at molecular level is not available for the
hydration of the cement particles and for the
improvement of workability of the mix. These
effects result in the stiffening of the cementitious
system.
Water reducers are negatively charged organic
molecules that adsorb primarily at the solid-liquid
interface with cement and water. Water reducers
cause uniformity of like charges at the cement
particle surfaces, causing them to repel each other.
This disperses the particles in the paste.
G-2 Effects of Dispersion
a) Option 1 — This dispersion increases the
effectiveness of the water, causing the mix
to become much more fluid for any given
water content. The effect is called
super plasticising, depending on the degree
of fluidity obtained.
b) Option 2 — If the increased fluidity is not
required, the water content of the mix can be
decreased, giving a lower water/cement ratio
and hence increased strength and durability.
This is called ‘water reduction’ or ‘high
range water reduction’.
c) Option 3 — A third option is to use an
admixture dosage that will ensure both of
these effects at the same time, for example
lower water/cement ratio and some
increase in fluidity.
The primary difference between high range water
reducing and conventional water-reducing
admixtures is that high-range water-reducing
(HRWR) admixtures, often referred to as
superplasticizers, may reduce the water requirement
by more than 30 percent, without the side effect of
excessive retardation.
G-3 The main constituents of water reducing
admixtures (plasticisers) are lignosulhonates or
selected carbohydrates. The typical dose of
plasticisers is in the
range of is 0.3 to 0.5 percent and water reduction of 8 admixtures. While retarding type superplasticisers
to may be more appropriate in certain cases to avoid
12 percent can be achieved. These may be adopted abnormal slump loss due to longer transportation
for lower grades of concrete. time and relatively lower dosages may be adopted
HRWR admixtures (superplasticisers) are organic to avoid adverse effects of delayed setting time of
products that typically fall into three families based concrete and additional air entrainment. Few trials
on ingredients: may be very useful for this purpose.
1) Sulfonated melamine-formaldehyde G-5 Sometimes problems due to cement admixture

condensate, SMFC; incompatibility are experienced. An admixture that
2) Sulfonated naphthalene-formaldehyd e produces all the desired effects with one cement may
condensate SNFC; and not do the same with another cement. This problem is
particularity experienced when the supply of cement
3) Polyether-polycarboxylates, PCE.
and/or admixture is changed midway through a
The typical dose of superplastisers is in the range of project. Cement admixture incompatibility may result
0.5 to 1.5 percent and water reduction of 15 to 30 in rapid loss of workability, bleeding and
percent and more can be achieved. PCE type segregation of concrete, acceleration/ retardation of
superplasticers are used in lower dosages and give setting, low rates of strength gain and entrainment of
high water reduction of 30 percent and more and air. Compatible combinations of cement and
are particularly suitable for high strength concrete superplasticiser may be selected by trials or by simple
and for self compacting concrete. tests like Marsh cone test.
G-4 The adverse effects on slump loss, delayed G-6 Admixtures shall satisfy all requirements of
setting time of concrete and additional air entrapment IS 9103 and IS 456.
shall be kept in mind while deciding type and dosage
of various
ANNEX H
(Foreword)
COMMITTEE COMPOSITION
Cement and Concrete Sectional Committee, CED 02
Organization Representive(S)
In Personal Capacity, (14A, Summer Breeze, Seasons, SHRI J OSE K URIAN (Chairman)
Kuravankonam, Kowdiar, Thiruvananthapuram 695003)
ACC Ltd, Mumbai SHRI S. A. KHADILKAR

SHRI RAMAN SADANAND P ARULEKAR (Alternate)
Ambuja Cements Limited, Ahmedabad SHRI J. P. DESAI
DR BIBEKANANDA MOHAPATRA (Alternate)
Atomic Energy Regulatory Board, Mumbai SHRI L. R. B ISHNOI
SHRI SOURAV ACHARYA (Alternate)
Builders’ Association of India, Mumbai SHRI S USHANTA KUMAR B ASU
SHRI D. R. SEKOR (Alternate)
Building Materials and Technology Promotion Council, New Delhi SHRI J. K. PRASAD
SHRI C. N. JHA (Alternate)
Cement Manufacturers’ Association, Noida SHRI RAKESH BHARGAVA
DR S. K. HANDOO (Alternate)
Central Public Works Department, New Delhi SHRI A. K. GARG
SHRI RAJESH KHARE (Alternate)
Central Soil and Materials Research Station, New Delhi DIRECTOR
SHRI N. S IVA KUMAR (Alternate)
Central Water Commission, New Delhi DIRECTOR (CMDD) (N&W)
DEPUTY DIRECTOR (CMDD) (NW&S) (Alternate)
Conmat Technologies Private Limited, Kolkata DR A. K. C HATTERJEE
SHRI SUBRATO CHOWDHURY (Alternate)
Construction Chemical Manufacturers’ Association, Mumbai SHRI S AMIR SURLAKER
SHRI NILOTPOL KAR (Alternate)
CSIR – Central Building Research Institute, Roorkee SHRI S. K. S INGH
SHRI S UBHASH GURRAM (Alternate)
CSIR – Central Road Research Institute, New Delhi SHRI J. B. S ENGUPTA
SHRI SATISH PANDEY (Alternate)
CSIR – Structural Engineering Research Centre, Chennai DR K. R AMANJANEYULU
DR P. SRINIVASAN (Alternate)
Delhi Development Authority, New Delhi SHRI LAXMAN SINGH
SHRI VIJAY SHANKAR (Alternate)
Engineers India Limited, New Delhi SHRI RAJANJI SRIVASTAVA
SHRI ANURAG SINHA (Alternate)
Department of Science & Technology, Ministry of Science and SHRI CHANDER MOHAN
Technology New Delhi
Gammon India Limited, Mumbai SHRI V. N. HEGGADE
SHRI S. C. UPADHYAY (Alternate)
Hindustan Construction Company Ltd, Mumbai SHRI S ATISH KUMAR S HARMA
DR CHETAN HAZAREE (Alternate)
Housing and Urban Development Corporation Limited, New Delhi SHRI DEEPAK BANSAL
Indian Association of Structural Engineers, New Delhi SHRI MAHESH TANDON

SHRI GANESH JUNEJA (Alternate)
Indian Concrete Institute, Chennai SHRI VIVEK NAIK
SECRETARY GENERAL (Alternate)
Indian Institute of Technology Delhi, New Delhi REPRESENTATIVE
IS 10262 : 2019
Indian Institute of Technology Madras, Chennai PROF DEVDAS MENON

DR MANU S ANTHANAM (Alternate)
Indian Institute of Technology Roorkee, Roorkee PROF V. K. GUPTA
DR BHUPINDER SINGH (Alternate)
Indian Roads Congress, New Delhi SECRETARY G ENERAL
DIRECTOR (Alternate)
Institute for Solid Waste Research and Ecological Balance, DR N. B HANUMATHIDAS
Visakhapatnam SHRI N. KALIDAS (Alternate)
Military Engineer Services, Engineer-in-Chief ’s Branch, Army HQ, MAJ GEN S. K. S RIVASTAV
New Delhi SHRI MAN SINGH (Alternate)
Ministry of Road Transport & Highways, New Delhi SHRI A. P. PATHAK
SHRI A. K. P ANDEY (Alternate)
National Council for Cement and Building Materials, Ballabgarh SHRI V. V. ARORA
DR S. HARSH (Alternate)
National Test House, Kolkata SHRI SHIR S INGH
SHRIMATI S. A. KAUSHIL (Alternate)
Nuclear Power Corporation of India Ltd, Mumbai SHRI ARVIND S HRIVASTAVA
SHRI RAGHUPATI ROY (Alternate)
Nuvoco Vistas Corporation Ltd, Mumbai SHRI PRANAV DESAI
SHRI RAVINDRA KHAMPARIA (Alternate)
OCL India Limited, New Delhi DR S. C. AHLUWALIA
Public Works Department, Government of Tamil Nadu, Chennai SUPERINTENDING ENGINEER
EXECUTIVE ENGINEER (Alternate)
The India Cements Limited, Chennai DR D. VENKATESWARAN
The Indian Hume Pipe Company Limited, Mumbai SHRI P. R. BHAT
SHRI S. J. SHAH (Alternate)
The Institution of Engineers (India), Kolkata DR H. C. VISVESVARAYA
SHRI S. H. JAIN, FIE (Alternate)
The Ramco Cements Limited, Chennai SHRI BALAJI K. MOORTHY
SHRI ANIL KUMAR PILLAI (Alternate)
Ultra Tech Cement Limited, Mumbai SHRI S URYA VALLURI
DR M. R. KALGAL (Alternate)
Voluntary Organization in Interest of Consumer Education, SHRI M. A. U. KHAN
New Delhi SHRI B. MUKHOPADHYAY (Alternate)
In personal capacity (EA-92, Maya Enclave, Hari Nagar, SHRI R. C. WASON
New Delhi)
In personal capacity (36, Old Sneh Nagar, Wardha Road, Nagpur) SHRI L. K. J AIN
In personal capacity [B-806, Oberoi Exquisite, Oberoi Garden SHRI A. K. J AIN
City, Goregaon (East), Mumbai]
In personal capacity (E-1, 402, White House Apartments, R. T. SHRI S. A. REDDI
Nagar, Bengaluru)
BIS Directorate General SHRI SANJAY PANT, Scientist ‘F’ and Head (Civil
Engineering) [Representing Director General (Ex-officio)]
Member Secretary
SHRIMATI DIVYA S.
Scientist ‘B’ (Civil Engineering), BIS
Concrete Subcommittee, CED 2:2
In Personal Capacity, (14A, Summer Breeze, Seasons, SHRI J OSE KURIAN (Convener)
Kuravankonam, Kowdiar, Thiruvananthapuram 695003)
ACC Limited, Mumbai SHRI AVIJIT CHAUBEY
Ambuja Cement Limited, Ahmedabad SHRI J. P. DESAI
DR BIBEKANANDA MOHAPATRA (Alternate)
IS 10262 : 2019
Organization
Organizatio Representive(S )
n )
Association of Consulting Civil Engineers (India), Bengaluru SHRI AVINASH D. S HIRODE
SHRI K. K. MEGHASHYAM (Alternate)
Atomic Energy Regulatory Board, Mumbai SHRI L. R. B ISHNOI
SHRI SOURAV ACHARYA (Alternate)
Building Materials and Technology Promotion Council, New Delhi SHRI J. K. PRASAD
SHRI PANKAJ GUPTA (Alternate)
Bureau of Design for Hydel and Irrigation Project, Bhopal SHRI S. K. KHARE
SHRI BHAGWATI P RASAD GUPTA (Alternate)
Central Public Works Department, New Delhi SHRI A. K. GARG
SHRI RAJESH KHARE (Alternate)
Central Soil and Materials Research Station, New Delhi SHRI R AJEEV K UMAR
SHRI M. RAJA (Alternate)
Civil-Aid Technoclinic Pvt Ltd, Bengaluru SHRI M. S. SUDARSHAN
SHRI R. NAGENDRA (Alternate)
Creative Design Consultants and Engineers Pvt Ltd, Ghaizabad SHRI AMAN D EEP
CSIR – Central Building Research Institute, Roorkee DR RAJESH DEOLIA
SHRI H. C. ARORA (Alternate)
CSIR – Central Road Research Institute, New Delhi SHRI J. B. S ENGUPTA
SHRI SATISH PANDEY (Alternate)
CSIR – Structural Engineering Research Centre, Chennai DR B. H. BHARATH K UMAR
DR P. SRINIVASAN (Alternate)
Elkem South Asia Pvt Ltd, Navi Mumbai SHRI BRAJESH MALVIYA
SHRI S URENDRA S HARMA (Alternate)
Engineers India Limited, New Delhi SHRI RAJANJI SRIVASTAVA
SHRI ANURAG SINHA (Alternate)
Department of Science and Technology, Ministry of Science and DR CHANDER MOHAN
Technology New Delhi
Gammon India Limited, Mumbai SHRI M ANISH MOKAL
SHRI SUDEESH RAJENDRAN (Alternate)
Hindustan Construction Company Ltd, Mumbai DR CHETAN HAZARE
SHRI AVINASH HARDE (Alternate)
Indian Concrete Institute, Chennai SHRI K. C. TAYADE
SECRETARY GENERAL (Alternate)
Indian Institute of Structural Engineering, Mumbai SHRI D. S. JOSHI
SHRI HEMANT VADALKAR (Alternate)
Indian Institute of Technology Delhi, New Delhi DR B. BHATTACHARJEE
DR SHASHANK BISHNOI (Alternate)
Indian Institute of Technology Kanpur, Kanpur DR SUDHIR M ISHRA
Indian Institute of Technology Madras, Chennai DR MANU S ANTHANAM
Indian Institute of Technology Roorkee, Roorkee DR ASHOK KUMAR JAIN
Indian Society of Structural Engineers, Mumbai SHRI D. S. JOSHI
SHRI HEMANT VADALKAR (Alternate)
Irrigation and Power Research Institute, Amritsar C HIEF ENGINEER (RESEARCH )
RESEARCH OFFICER (Alternate)
Larsen and Toubro Limited, ECC Division, Chennai DR B. SIVARAMSARMA
SHRI S. MANOHAR (Alternate)
Military Engineer Services, Engineer-in-Chief’s Branch, SHRI S. K. S RIVASTAV
Army HQ, New Delhi SHRI MAN SINGH (Alternate)
Ministry of Road Transport and Highways, New Delhi SHRI A. P. PATHAK
SHRI A. K. P ANDEY (Alternate)
National Buildings Construction Corporation Limited, Haryana SHRI H. S. Y ADAV
SHRI PAWAN KUMAR (Alternate)
SHRI S. SHARMA (Alternate)
IS 10262 : 2019
National Institute of Technology, Warangal DR C. B. KAMESWARA RAO

DR D RAMA SESHU (Alternate)
Nuclear Power Corporation of India Limited, Mumbai SHRI ARVIND S HRIVASTAVA
SHRI N. M. RAO (Alternate)
Pidilite Industries Limited, Mumbai DR SUGUNA NAIK
Ready Mixed Concrete Manufacturers’ Association, Mumbai SHRI VIJAYKUMAR R. KULKARNI
SHRI ANIL KULKARNI (Alternate)
Research, Design and Standards Organization (Ministry of J OINT DIRECTOR (B&S)/CB-I
Railways), Lucknow JOINT DIRECTOR (B&S)/CB-II (Alternate)
Shapoorji Pallonji and Company Private Limited, Mumbai SHRI GIRISH BONDE
SHRI D. N. VISHWANATH (Alternate)
Tandon Consultants Private Limited, New Delhi SHRI MAHESH TANDON
SHRI VINAY GUPTA (Alternate)
Tata Consulting Engineers Limited, Mumbai SHRI S. N. DIWAKAR
SHRI MANOS KUMAR DE (Alternate)
Ultra Tech Cement Limited, Mumbai DR V. RAMACHANDRA
DR A. K. S INGH (Alternate)
Water Resource Department (Government of M.P), Mumbai SHRI S. K. KHARE
SHRI B. P. G UPTA
(Alternate) In personal capacity (#452, Sector-14, Sonipat, Haryana) SHRI R. K. JAIN
In personal capacity (36 Old Sneh Nagar, Wardha Road, Nagpur) SHRI LALIT KUMAR JAIN
In personal capacity [B-806, Oberoi Exquisite, Oberoi Garden SHRI A. K. J AIN
City, Goregaon (East), Mumbai]
In personal capacity (E-1, 402 White House Apartments, R. T. SHRI S. A. REDDI
Nagar, Bengaluru)
In personal capacity (EA-92, Maya Enclave, Hari Nagar, New Delhi) SHRI R. C. WASON
In personal capacity (M1F1 VGN Minerva Apartments, Guruswamy DR C. RAJKUMAR
Road, Nolambur, Chennai)
Working Group for the Revision of IS 10262, CED 2:2/WG 3
In Personal Capacity, (EA-92, Maya Enclave, Hari Nagar, SHRI R. C. WASON (Convener)
New Delhi)
National Council for Cement and Building Materials, Ballabgarh SHRI SURESH KUMAR
In Personal Capacity, (50, Mangla Apartment, Kalkaji, New Delhi) DR S. C. MAITI
(Continued from second cover)
as ten materials. Now, apart from the four ingredients mentioned above, fly ash, ground granulated blast
furnace slag, silica fume, rice husk ash, metakaoline and superplasticizer are six more ingredients which are
generally used in concrete produced in practice as the situation demands. Also, now high strength concrete, self
compacting concrete, apart from ordinary concrete and mass concrete, are also being produced and used in
projects. Hence, it is all the more essential at this juncture to have general guidelines on proportioning concrete
mixes to cover these aspects.
The objective of proportioning concrete mixes is to arrive at the most economical and practical combinations of
different ingredients to produce concrete that will satisfy the performance requirements under specified
conditions of use. An integral part of concrete mix proportioning is the preparation of trial mixes and marking
adjustments to such trials to strike a balance between the requirements of placement, that is, workability and
strength, concomitantly satisfying durability requirements.
Concrete has to be of satisfactory quality both in its fresh and hardened state. This task is best accomplished by
trial mixes arrived at by the use of certain established relationships among different parameters and by analysis
of data already generated thereby providing a basis for judicious combination of all the ingredients involved.
The basic principles which underline the proportioning of mixes are Abram’s law for strength development and
Lyse’s rule for making mix with adequate workability for placement in a dense state so as to enable the strength
development as contemplated. From practical view point, compressive strength is often taken as an index of
acceptability. This does not necessarily satisfy the requirements of durability unless examined under specific
context. Mix proportioning is generally carried out for a particular compressive strength requirement, ensuring
that fresh concrete of the proportioned mix possess adequate workability for placement without segregation and
bleeding while attaining a dense state. In addition, the method has scope to consider the combination of wider
spectrum of cement and mineral admixtures proposed to be used to meet the requirements of durability for the
type of exposure conditions anticipated in service.
Proportioning of concrete mixes can be regarded as a procedure set to proportion the most economical concrete
mix, for specified durability and grade, for required site conditions.
As a guarantor of quality of concrete in the construction, the constructor should carry out mix proportioning
and the engineer-in-charge should approve the mix so proportioned. The method given in this standard is to be
regarded as the guidelines only to arrive at an acceptable product, which satisfies the requirements of placement
required with development of strength with age and ensures the requirements of durability. It is suggested that
the concrete mix proportioning in the laboratory may be carried out at a temperature of 27± 2°C, relative
humidity of minimum
60 percent, and the temperature of concrete may be 27 ± 3°C.
This standard does not debar the adoption of any other established methods of concrete mix proportioning.
The composition of the Committee responsible for the formulation of this standard is given in Annex H.
For the purpose of deciding whether a particular requirement of this standard is complied with, the final value,
observed or calculated, expressing the result of a test or analysis, shall be rounded of in accordance with IS 2 :
1960
‘Rules for rounding off numerical values (revised)’ .The number of significant places retained in the rounded
off value should be the same as that of the specified value in this standard.
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 2016 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of
‘BIS Catalogue’ and ‘Standards : Monthly
Additions’.
This Indian Standard has been developed from Doc No.: CED 02 (11290).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS
Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones : 2323 0131, 2323 3375, 2323 9402 Website: www.bis.org.in
Regional Offices: Telephones
Central
NEW DELHI 110002
: Manak Bhavan, 9 Bahadur Shah Zafar Marg
{ 2323 3841
2323 7617
KOLKATA
700054
{ 2337 8626, 2337 9120
Eastern : 1/14 C.I.T. Scheme VII M, V. I. P. Road, Kankurgachi 2337 8499, 2337 8561
Northern : Plot No. 4-A, Sector 27-B, Madhya Marg, CHANDIGARH 160019
{ 26 50206
265 0290
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113
{ 2254 1216, 2254 1442
2254 2519, 2254 2315
Western
MUMBAI 400093
: Manakalaya, E9 MIDC, Marol, Andheri (East)
{ 2832 7891, 2832 7892
2832 9295, 2832 7858

Branches: A H M E D A B A D . B E N G A L U R U . B H O PA L . B H U B A N E S WA R . C O I M B AT O R E .
D E H R A D U N . D U R G A P U R . FA R I D A B A D . G H A Z I A B A D . G U WA H AT I .
HYDERABAD. JAIPUR. JAMMU. JAMSHEDPUR. KOCHI. LUCKNOW. NAGPUR.
PA R WA N O O . PAT N A . PUNE. RAIPUR. R A J K O T. VISAKHA
PAT N A M .
Published by BIS, New Delhi

4.IS 10262 2019 New Mix Design

Uploaded by

Copyright:

Available Formats

4.IS 10262 2019 New Mix Design

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4.IS 10262 2019 New Mix Design

Uploaded by

Copyright:

Available Formats

(Reaffirmed 0) Hkkjrh; ekud IS 10262 : 2019

oaQØhV feJ vuqikru —

Concrete Mix Proportioning —

Hkkjrh; ekud C;wjks

January 2019 Price Group 12

(Continued on third cover)

f’ck = target mean compressive strength at 28 (n1  n2 − 2)

Table 9 Recommended Dosages of Mineral Admixtures Materials for High Strength

6.3 Illustrative Examples 7.2.1 Filling Ability (flowability)

7 GENERAL The following are typical slump-flow classes for a

9.5 Selection of Water Cement

9.6 Calculation of Cement/Cementitious

These values shall be compared with those M ix No. 2 to 4 no r ma l l y pr ov ide s s uff ic

A-1 STIPULATIONS FOR PROPORTIONING

2) Fine aggregate : Conforming to grading Zone II of Table 9 of

From Table 1, X = 6.5. A-8 PROPORTION OF VOLUME OF COARSE

B-1 STIPULATIONS FOR PROPORTIONING

B - 3 TAR GE T S T RE NGT H FOR B-6 SELECTION OF WATER CONTENT

In the present case water-cementitious ratio is 0.327. 4.74 1

C-1 STIPULATIONS FOR PROPORTIONING

To proportion a mix containing GGBS the following

D-1 STIPULATIONS FOR PROPORTIONING

2) Fine aggregate : Conforming to grading Zone II of Table 9 of IS

S = standard deviation, and The cementitious material content

D-6 SELECTION OF WATER

a) f’ck = fck+1.65 S Cementitious material content

F-8 PROPORTION OF VOLUME OF COARSE

Sieve Percentage Passing Percentage of Different Combined Combined

G-1 Cement particles have a strong tendency to plasticising or

1) Sulfonated melamine-formaldehyde G-5 Sometimes problems due to cement admixture

ACC Ltd, Mumbai SHRI S. A. KHADILKAR

Indian Association of Structural Engineers, New Delhi SHRI MAHESH TANDON

Indian Institute of Technology Madras, Chennai PROF DEVDAS MENON

Concrete Subcommittee, CED 2:2

National Institute of Technology, Warangal DR C. B. KAMESWARA RAO

Working Group for the Revision of IS 10262, CED 2:2/WG 3

Review of Indian Standards

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

Regional Offices: Telephones

2832 9295, 2832 7858

You might also like