VDF - Svx030a1-4a1b2 - Um

Effective June 2009
9000X AF Drives Supersedes October 2007
User Manual
9000X AF Drives User Manual
June 2009
Important Notice – Please Read

The product discussed in this literature is subject to terms and conditions outlined in Eaton
Electrical Inc. selling policies. The sole source governing the rights and remedies of any
purchaser of this equipment is the relevant Eaton Electrical Inc. selling policy.
NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A

PARTICULAR PURPOSE OR MERCHANTABILITY, OR WARRANTIES ARISING FROM COURSE
OF DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE INFORMATION,
RECOMMENDATIONS AND DESCRIPTIONS CONTAINED HEREIN. In no event will Eaton
Electrical Inc. be responsible to the purchaser or user in contract, in tort (including
negligence), strict liability or otherwise for any special, indirect, incidental or consequential
damage or loss whatsoever, including but not limited to damage or loss of use of equipment,
plant or power system, cost of capital, loss of power, additional expenses in the use of
existing power facilities, or claims against the purchaser or user by its customers resulting
from the use of the information, recommendations and descriptions contained herein.
The information contained in this manual is subject to change without notice.
Cover Photo: Cutler-Hammer® SVX9000/SPX9000 AF Drives.
MN04001004E For more information visit: www.eaton.com i

June 2009
Table of Contents
LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
LIST OF TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Definitions and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Hazardous High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
CHAPTER 1 — OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Receiving and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Open SVX9000/SPX9000 Catalog Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
CHAPTER 2 — MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Standard Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
CHAPTER 3 — POWER WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
UL Compatible Cable Selection and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
UL Compatible Cable Selection and Installation with Breaker. . . . . . . . . . . . . . . . . 3-6
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Standard Wiring Diagrams and Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Power and Motor Wiring Terminal Photos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Checking the Cable and Motor Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
CHAPTER 4 — CONTROL WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Control Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
CHAPTER 5 — MENU INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
CHAPTER 6 — START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Sequence of Operation to Commission an Induction Motor . . . . . . . . . . . . . . . . . . 6-3
Manual Tuning of the SVX9000/SPX9000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Closed Loop Vector Control Manual Tuning (SPX9000 Only). . . . . . . . . . . . . . . . . . 6-11
APPENDIX A — TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Power Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Power Loss and Switching Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
EMC Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-27
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-27
Warranty and Liability Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-28
APPENDIX B — FAULT AND WARNING CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
APPENDIX C — TROUBLESHOOTING CHARTS USING FAULT CODES . . . . . . . . . . . . . C-1
APPENDIX D — SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Series Option Board Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Drive Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Spare Units & Replacement Parts for 9000X Drives . . . . . . . . . . . . . . . . . . . . . . . . . D-5
ii For more information visit: www.eaton.com MN04001004E

June 2009
List of Figures
Figure 2-1: Mounting Space Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Figure 3-1: Input Power and Motor Cable Stripping and Wire Lengths . . . . . . . . . . . . . . 3-8
Figure 3-2: Wiring Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Figure 3-3: Ground Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Figure 3-4: Cable Protection Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Figure 3-5: Principle Wiring Diagram of SVX9000/SPX9000 Power Unit,
FR4 to FR5 and FR6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
FR6, FR7 and FR8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
FR9 to FR10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Figure 3-8: FR4 Power and Motor Wiring Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Figure 3-9: FR5 Power and Motor Wiring Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Figure 3-10: FR6 Power and Motor Wiring Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Figure 4-1: Option Board Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Figure 4-2: Option Board A9 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-3: Option Board A9 Jumper Location and Settings . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-4: Option Board A2 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-5: Option Board A2 Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-6: Positive/Negative Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 5-1: Keypad and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Figure 5-2: Main Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 5-3: Parameter Menu Structure Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Figure 5-4: Keypad Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Figure 5-5: Active Fault Display Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Figure 5-6: Sample Fault History Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-7: System Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Figure 5-8: Expander Board Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Figure 5-9: Digital Inputs — DIN1, DIN2, DIN3 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Figure 5-10: Digital Inputs — DIN4, DIN5, DIN6 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Figure 5-11: Digital and Relay Outputs — DO1, RO1, RO2 Status . . . . . . . . . . . . . . . . . . 5-19
Figure 5-12: Operate Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Figure 6-1: Open Loop Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Figure 6-2: Motor Current after V/f-Curve Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Figure 6-3: Motor Equivalent Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Figure 6-4: Left: OL Speed Control Off. Right: OL Speed Control ON. . . . . . . . . . . . . . . . 6-10
Figure 6-5: Closed Loop Motor Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Figure 6-6: Closed Loop Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Figure A-1: SVX9000/SPX9000 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Figure A-2: Power Loss as Function of Switching Frequency —
3/4 – 3 hp 230V, 1 – 5 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
5 – 7-1/2 hp 230V, 7-1/2 – 15 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
10 – 15 hp 230V, 20 – 30 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
20 – 30 hp 230V, 40 – 60 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9
MN04001004E For more information visit: www.eaton.com iii

June 2009
List of Figures (Continued)

75 – 125 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9
150 – 200 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Figure A-8: NEMA Type 1 Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
Figure A-9: NEMA Type 1 and 12 with Flange Kit, FR4, FR5 and FR6
Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
Figure A-10: NEMA Type 1 with Flange Kit, FR7 and FR8 Enclosure Dimensions . . . . . A-13
Figure A-11: FR9 Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14
Figure A-12: FR9 with Flange Kit Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Figure A-13: SPX9000 Dimensions, FR10 Open Chassis . . . . . . . . . . . . . . . . . . . . . . . . . A-16
Figure A-14: SPX9000 Dimensions, FR11 Open Chassis . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Figure A-15: SPX9000 Dimensions, FR13 Open Chassis Inverter . . . . . . . . . . . . . . . . . . A-18
Figure A-16: SPX9000 Dimensions, FR13 Open Chassis Converter . . . . . . . . . . . . . . . . A-19
Figure A-17: SPX9000 Dimensions, FR13 Open Chassis Converter —
900/1000 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-20
Figure A-18: AC Choke (CHK0650) Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21
Figure A-22: Control Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-25
Figure A-23: Control Unit with Star-Coupler Board, FR12 or FR14 Only . . . . . . . . . . . . . A-26
Figure C-1: F1 — Overcurrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Figure C-2: F2 — Overvoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Figure C-3: F3 — Earth Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Figure C-4: F5 — Charging Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Figure C-5: F6 — Emergency Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Figure C-6: F7 — Saturation Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Figure C-7: F8 — System Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Figure C-8: F9 — Undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Figure C-9: F10 — Input Line Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
Figure C-10: F11 — Output Phase Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10
Figure C-11: F12 — Brake Chopper Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
Figure C-12: F13 — Frequency Converter Under Temperature . . . . . . . . . . . . . . . . . . . . C-12
Figure C-13: F14 — Frequency Converter Over Temperature . . . . . . . . . . . . . . . . . . . . . C-13
Figure C-14: F15 — Motor Stalled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
Figure C-15: F16 — Motor Over Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-15
Figure C-16: F17 — Motor Under Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16
Figure C-17: F22 — Param Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17
Figure C-18: F24 — Counter Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18
Figure C-19: F25 — Microprocessor Watchdog Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18
Figure C-20: F31 — IGBT Temperature (Hardware) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-19
Figure C-21: F32 — Fan Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-20
Figure C-22: F36 — Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-21
Figure C-23: F37 — Device Change (Indication Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-21
Figure C-24: F38 — Device Added (Indication Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-22
Figure C-25: F39 — Device Removed (Indication Only) . . . . . . . . . . . . . . . . . . . . . . . . . . C-22
Figure C-26: F40 — Device Unknown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-23
Figure C-27: F41 — IGBT Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-24
Figure C-28: F42 — Brake Resistor Over Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . C-25
iv For more information visit: www.eaton.com MN04001004E

June 2009
List of Figures (Continued)

Figure C-29: F44 — DevParChange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-26
Figure C-30: F45 — DevParAdded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-27
Figure C-31: F50 — Analog Input Iin < 4 mA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-28
Figure C-32: F51 — External Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-29
Figure C-33: F52 — Keypad Communication Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-30
Figure D-1: 9000X Series Option Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
List of Tables
Table 1-1: SVX9000/SPX9000 AF Drive Catalog Numbering System . . . . . . . . . . . . . . . . 1-2
Table 2-1: Space Requirements for Mounting a SVX9000/SPX9000 Drive . . . . . . . . . . . . 2-1
Table 2-2: Cooling Airflow Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Table 3-1: Cable Spacings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Table 3-2: 40°C Cable and Fuse Sizes — 230V Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Table 3-5: Cable and Busbar Sizes, SPX FR10 – FR12 — 480V Ratings . . . . . . . . . . . . . . . 3-4
Table 3-9: Maximum Symmetrical Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Table 3-10: Cable and Breaker Sizes – 230V Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Table 3-13: Power Connection Tightening Torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Table 3-14: Power and Motor Cable Stripping Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Table 4-1: Tightening Torques of Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-2: Control Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Table 4-3: Option Board A9 Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Table 4-4: Option Board A2 Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Table 5-1: LCD Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Table 5-2: LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Table 5-3: Navigation Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Table 5-4: Fault Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Table 5-5: Fault Time Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Table 5-6: Total Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Table 5-7: Trip Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Table 5-8: Software Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Table 5-9: Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Table 5-10: Hardware Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Table 5-11: Expander Board Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Table 5-12: Monitoring Menu Items — Standard Application Example . . . . . . . . . . . . . . 5-19
Table 5-13: Operate Menu Items — Standard Application Example . . . . . . . . . . . . . . . . . 5-20
Table A-1: SVX9000/SPX9000 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Table A-2: Output Power Ratings — 230V IH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Table A-4: Output Power Ratings — 480V SPX FR10 – FR14 . . . . . . . . . . . . . . . . . . . . . . . A-5
Table A-6: Output Power Ratings — 575V SPX FR10 – FR14 . . . . . . . . . . . . . . . . . . . . . . . A-6
Table A-7: NEMA Type 1/Type 12 Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
Table A-8: FR4, FR5 and FR6 with Flange Kit Enclosure Dimensions . . . . . . . . . . . . . . . . A-12
Table A-9: FR7 and FR8 with Flange Kit Enclosure Dimensions. . . . . . . . . . . . . . . . . . . . . A-13
MN04001004E For more information visit: www.eaton.com v

June 2009
List of Tables (Continued)

Table A-10: FR9 Enclosure Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14
Table A-11: FR9 with Flange Kit Enclosure Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Table A-12: Dimensions for SPX9000, FR10 Open Chassis . . . . . . . . . . . . . . . . . . . . . . . . A-16
Table A-13: Dimensions for SPX9000, FR11 Open Chassis . . . . . . . . . . . . . . . . . . . . . . . . A-17
Table A-14: Dimensions for SPX9000, FR13 Open Chassis Inverter . . . . . . . . . . . . . . . . . A-18
Table A-15: FR13 — Number of Input Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-19
Table A-16: Dimensions for SPX9000, FR13 Open Chassis Converter . . . . . . . . . . . . . . . A-19
Table A-17: FR13 — Number of Input Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-20
Table A-18: Dimensions for SPX9000, FR13 Open Chassis Converter —
900/1000 hp 480V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-20
Table B-1: Fault Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Table D-1: Option Board Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Table D-2: Control Panel Factory Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Table D-3: 9000X Spare Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
Table D-4: Replacement Parts — 9000X Drives, 208 – 240V . . . . . . . . . . . . . . . . . . . . . . . D-5
Table D-5: Replacement Parts — FR4 – FR9 9000X Drives, 380 – 500V . . . . . . . . . . . . . . D-7
Table D-6: Replacement Parts — FR10 – FR12 9000X Drives, 380 – 500V . . . . . . . . . . . . D-9
Table D-7: Replacement Parts — FR6 – FR9 9000X Drives, 525 – 690V . . . . . . . . . . . . . . D-11
Table D-8: Replacement Parts — FR10 – FR12 9000X Drives, 525 – 690V . . . . . . . . . . . . D-13
Table D-9: Power Module Catalog Number Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14
Table A-10: FR9 Enclosure Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14
vi For more information visit: www.eaton.com MN04001004E

June 2009
Safety
Definitions and Symbols
WARNING
This symbol indicates high voltage. It calls your attention to items
or operations that could be dangerous to you and other persons
operating this equipment. Read the message and follow the
instructions carefully.
This symbol is the “Safety Alert Symbol.” It occurs with either of

two signal words: CAUTION or WARNING, as described below.
WARNING
Indicates a potentially hazardous situation which, if not avoided,
can result in serious injury or death.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
can result in minor to moderate injury, or serious damage to the
equipment. The situation described in the CAUTION may, if not
avoided, lead to serious results. Important safety measures are
described in CAUTION (as well as WARNING).
Hazardous High Voltage
WARNING
Motor control equipment and electronic controllers are connected
to hazardous line voltages. When servicing drives and electronic
controllers, there may be exposed components with housings or
protrusions at or above line potential. Extreme care should be taken
to protect against shock.
• Stand on an insulating pad and make it a habit to use only one
hand when checking components.
• Always work with another person in case an emergency occurs.
• Disconnect power before checking controllers or performing
maintenance.
• Be sure equipment is properly grounded.
• Wear safety glasses whenever working on electronic controllers
or rotating machinery.
MN04001004E For more information visit: www.eaton.com vii

June 2009
Warnings and Cautions

Read this manual thoroughly and make sure you understand the procedures before you
attempt to install, set up, or operate this Cutler-Hammer® SVX9000/SPX9000 Adjustable
Frequency Drive from Eaton’s electrical business.
Warnings
WARNING
Be sure to ground the unit following the instructions in this manual.
Ungrounded units may cause electric shock and/or fire.
WARNING
This equipment should be installed, adjusted, and serviced by
qualified electrical maintenance personnel familiar with the
construction and operation of this type of equipment and the
hazards involved. Failure to observe this precaution could result in
death or severe injury.
WARNING
Components within the SVX9000/SPX9000 power unit are live
when the drive is connected to power. Contact with this voltage is
extremely dangerous and may cause death or severe injury.
WARNING
Line terminals (L1, L2, L3), motor terminals (U, V, W) and the DC-
link/brake resistor terminals (-/+) are live when the drive is
connected to power, even if the motor is not running. Contact with
this voltage is extremely dangerous and may cause death or severe
injury.
WARNING
Even though the control I/O-terminals are isolated from line
voltage, the relay outputs and other I/O-terminals may have
dangerous voltage present even when the drive is disconnected
from power. Contact with this voltage is extremely dangerous and
may cause death or severe injury.
WARNING
The SVX9000/SPX9000 drive has a large capacitive leakage current
during operation, which can cause enclosure parts to be above
ground potential. Proper grounding, as described in this manual, is
required. Failure to observe this precaution could result in death or
severe injury.
WARNING
Before applying power to the SVX9000/SPX9000 drive, make sure
that the front and cable covers are closed and fastened to prevent
exposure to potential electrical fault conditions. Failure to observe
this precaution could result in death or severe injury.
viii For more information visit: www.eaton.com MN04001004E

June 2009
WARNING
An upstream disconnect/protective device must be provided as
required by the National Electric Code (NEC). Failure to follow this
precaution may result in death or severe injury.
WARNING
Before opening the SVX9000/SPX9000 drive covers:
• Disconnect all power to the SVX9000/SPX9000 drive.
• Wait a minimum of 5 (five) minutes after all the lights on the
keypad are off. This allows time for the DC bus capacitors to
discharge.
• A hazard voltage may still remain in the DC bus capacitors even
if the power has been turned off. Confirm that the capacitors
have fully discharged by measuring their voltage using a
multimeter set to measure DC voltage.
Failure to follow the above precautions may cause death or severe
injury.
Cautions
CAUTION
Do not perform any meggar or voltage withstand tests on any part
of the SVX9000/SPX9000 drive or its components. Improper testing
may result in damage.
CAUTION
Prior to any tests or measurements of the motor or the motor cable,
disconnect the motor cable at the SVX9000/SPX9000 output
terminals (U, V, W) to avoid damaging the SVX9000/SPX9000
during motor or cable testing.
CAUTION
Do not touch any components on the circuit boards. Static voltage
discharge may damage the components.
CAUTION
Any electrical or mechanical modification to this equipment
without prior written consent of Eaton will void all warranties and
may result in a safety hazard in addition and voiding of the UL
listing.
CAUTION
Install the SVX9000/SPX9000 drive on flame-resistant material such
as a steel plate to reduce the risk of fire.
MN04001004E For more information visit: www.eaton.com ix

June 2009
CAUTION
Install the SVX9000/SPX9000 drive on a perpendicular surface that
is able to support the weight of the drive and is not subject to
vibration, to lessen the risk of the drive falling and being damaged
and/or causing personal injury.
CAUTION
Prevent foreign material such as wire clippings or metal shavings
from entering the drive enclosure, as this may cause arcing
damage and fire.
CAUTION
Install the SVX9000/SPX9000 drive in a well-ventilated room that is
not subject to temperature extremes, high humidity, or
condensation, and avoid locations that are directly exposed to
sunlight, or have high concentrations of dust, corrosive gas,
explosive gas, inflammable gas, grinding fluid mist, etc. Improper
installation may result in a fire hazard.
Motor and Equipment Safety
CAUTION
Before starting the motor, check that the motor is mounted properly
and aligned with the driven equipment. Ensure that starting the
motor will not cause personal injury or damage equipment
connected to the motor.
CAUTION
Set the maximum motor speed (frequency) in the SVX9000/
SPX9000 drive according to the requirements of the motor and the
equipment connected to it. Incorrect maximum frequency settings
can cause motor or equipment damage and personal injury.
CAUTION
Before reversing the motor rotation direction, ensure that this will
not cause personal injury or equipment damage.
CAUTION
Make sure that no power correction capacitors are connected to the
SVX9000/SPX9000 output or the motor terminals to prevent
SVX9000/SPX9000 malfunction and potential damage.
CAUTION
Make sure that the SVX9000/SPX9000 output terminals (U, V, W)
are not connected to the utility line power as severe damage to the
SVX9000/SPX9000 may occur.
x For more information visit: www.eaton.com MN04001004E

June 2009
Chapter 1 — Overview
This chapter describes the purpose and contents of this manual, the receiving inspection
recommendations and the Cutler-Hammer® SVX9000/SPX9000 catalog numbering system.
How to Use This Manual

The purpose of this manual is to provide you with information necessary to install, set and
customize parameters, start up, troubleshoot and maintain the Cutler-Hammer SVX9000/
SPX9000 AF Drives by Eaton’s electrical business. To provide for safe installation and
operation of the equipment, read the safety guidelines at the beginning of this manual and
follow the procedures outlined in the following chapters before connecting power to the
SVX9000/SPX9000. Keep this user manual handy and distribute to all users, technicians and
maintenance personnel for reference along with the appropriate application manual.
Chapter 1 – Overview is the chapter you are reading now.
Chapter 2 – Mounting
Chapter 3 – Power Wiring
Chapter 4 – Control Wiring
Chapter 5 – Menu Information
Chapter 6 – Start-Up
Appendix A – Technical Data
Appendix B – Fault and Warning Codes
Appendix C – Troubleshooting Charts
Appendix D – Spare Parts
Receiving and Inspection

This SVX9000/SPX9000 AC drive has met a stringent series of factory quality requirements
before shipment. It is possible that packaging or equipment damage may have occurred
during shipment. After receiving your SVX9000/SPX9000 drive, please check for the
following:
● Check to make sure that the package(s) includes the proper drive, the User Manual, and
rubber conduit covers, screws, conduit plate and ground straps.
● Inspect the unit to ensure it was not damaged during shipment.
● Make sure that the part number indicated on the nameplate corresponds with the
Catalog Number on your order.
If shipping damage has occurred, please contact and file a claim with the carrier involved
immediately.
If the delivery does not correspond to your order, please contact your Eaton representative.
Note: Do not destroy the packing. The template printed on the protective cardboard can be
used for marking the mounting points of the SVX9000/SPX9000 AF Drives on the wall
or cabinet.
MN04001004E For more information visit: www.eaton.com 1-1

June 2009
Open SVX9000/SPX9000 Catalog Numbers

Table 1-1: SVX9000/SPX9000 AF Drive Catalog Numbering System
SVX 007A 1 - 4 A 1 B 1
Product Expansion Slots 3 through 5
SVX = SVX Industrial Drive • Option boards be selected from left
SPX = SPX Drive to right, in alpha-numeric order.
• Characters to be left blank if no
options are selected
Horsepower (IH)
F07 = 3/4 150 = 150 Board Modifications
001 = 1 200 = 200
F15 = 1-1/2 250 = 250 1 = Standard Boards (A9, A2)
002 = 2 300 = 300
003 = 3 350 = 350
004 = 5 IL Only 400 = 400 Braking
005 = 5 500 = 500 N = No Brake Chopper
006 = 7-1/2 IL Only 550 = 550 B = Internal Brake Chopper
007 = 7-1/2 600 = 600
010 = 10 650 = 650
015 = 15 700 = 700 Input Options
020 = 20 800 = 800
025 = 25 900 = 900 1 = 3-Phase, EMC H
030 = 30 H10 = 1000 2 = 3-Phase, EMC N
040 = 40 H12 = 1200 4 = 3-Phase, EMC L
050 = 50 H13 = 1350
060 = 60 H15 = 1500
Keypad
075 = 75 H16 = 1600
100 = 100 H20 = 2000 A = AlphaNumeric
125 = 125
Voltage
AFD Software Series
2 = 208 – 230V
A = Standard Software 4 = 380 – 500V
5 = 525 – 690V
Enclosure
0 = Open Chassis
1 = NEMA Type 1
2 = NEMA Type 12

All 230V Drives and 480V Drives up to 200 hp (IH) are only available with Input Option 1.
480V Drives 250 hp (IH) or larger are only available with Input Option 2.
480V Drives up to 30 hp (IH) are only available with Brake Chopper Option B.
480V Drives 40 hp (IH) and larger come with Brake Chopper Option N as standard.
230V Drives up to 15 hp (IH) are only available with Brake Chopper Option B.

230V Drives 20 hp (IH) or larger come with Brake Chopper Option N as standard.

480V Drives 250 hp, 300 hp and 350 hp (IH) are only available with Enclosure Style 0 (Chassis).
1-2 For more information visit: www.eaton.com MN04001004E

June 2009
Chapter 2 — Mounting
The SVX9000/SPX9000 drive may be mounted side-by-side or stacked vertically, as outlined
in the following section.
Space Requirements
To ensure proper air circulation and cooling, follow the guidelines below.
Table 2-1: Space Requirements for Mounting a SVX9000/SPX9000 Drive
Dimensions in Inches (mm)
Frame Drive Type A A2 B C D
4 230V, 1 – 3 hp IL, 3/4 – 3 hp IH 0.8 — 0.8 3.9 (100) 2.0

480V, 1 – 5 hp IH, 1-1/2 – 7-1/2 hp IL (20) (20) (50)
5 230V, 5 – 10 hp IL, 5 – 7-1/2 hp IH 1.2 — 0.8 4.7 (120) 2.4
480V, 7-1/2 – 15 hp IH, 10 – 20 hp IL (30) (20) (60)
6 230V, 15 – 20 hp IL, 10 – 15 hp IH 1.2 — 0.8 6.3 (160) 3.1
480V, 20 – 30 hp IH, 25 – 40 hp IL (30) (20) (80)
575V, 2 – 25 hp IH, 3 – 30 hp IL
7 230V, 25 – 40 hp IL, 20 – 30 hp IH 3.1 — 3.1 11.8 3.9 (100)
480V, 40 – 60 hp IH, 50 – 75 hp IL (80) (80) (300)
575V, 30 – 40 hp IH, 40 – 50 hp IL
8 480V, 75 – 125 hp IH, 100 – 150 hp IL 3.1 5.9 (150) 3.1 11.8 7.9 (200)
575V, 50 – 75 hp IH, 60 – 100 hp IL (80) (80) (300)
9 480V, 200 – 250 hp IL, 150 – 200 hp IH 2.0 — 3.1 15.7 9.8 (250)
575V, 100 – 150 hp IH, 150 – 200 hp IL (50) (80) (400) 13.8
(350)
Dimensions represent the minimum clearance needed when mounting a SVX9000/SPX9000. See Figure 2-1 below.
A = clearance around the SVX9000/SPX9000.
A2 = clearance needed to change the fan without disconnecting the motor cables.
B = distance between adjacent SVX9000/SPX9000 drives or between the SVX9000/SPX9000 and an enclosure wall.
C = clearance above the SVX9000/SPX9000.
D = clearance below the SVX9000/SPX9000.
Minimum clearance below the SVX9000/SPX9000 needed to change the fan.
B B
A
A2 A
A2
D
Figure 2-1: Mounting Space Requirements.
If several units are mounted above each other, the clearance between the drives should equal
C + D (see Table 2-1 and Figure 2-1 above). In addition, the outlet air used for cooling the
lower unit must be directed away from the inlet air used by the upper unit.

June 2009
Environmental Requirements
Ensure that the environment meets the requirements listed in Table A-1 of Appendix A for
any storage or operating situation.
Table 2-2 specifies the minimum airflow required in the area where the drive will be
mounted.
Table 2-2: Cooling Airflow Requirements
Drive Type Cooling Air Required
230V, 3/4 – 3 hp IH 41 cfm (70 m3/h)

480V, 1 – 5 hp IH
230V, 5 – 7-1/2 hp IH 112 cfm (190 m3/h)
480V, 7-1/2 – 15 hp IH
230V, 10 – 15 hp IH 250 cfm (425 m3/h)
480V, 20 – 30 hp IH
575V, 2 – 25 hp IH
230V, 20 – 30 hp IH 250 cfm (425 m3/h)
480V, 40 – 60 hp IH
575V, 30 – 40 hp IH
480V, 75 – 125 hp IH 383 cfm (650 m3/h)
575V, 60 – 75 hp IH
480V, 150 – 200 hp IH 765 cfm (1300 m3/h)
575V, 100 – 150 hp IH
Standard Mounting Instructions

1. Measure the mounting space to ensure that it allows for the minimum space
surrounding the drive. Drive dimensions are in Appendix A.
2. Make sure the mounting surface is flat and strong enough to support the drive, is not
flammable, and is not subject to excessive motion or vibration.
3. Ensure that the minimum airflow requirements for your drive are met at the mounting
location.
4. Mark the location of the mounting holes on the mounting surface, using the template
provided on the cover of the cardboard shipping package.
5. Using fasteners appropriate to your drive and mounting surface, securely attach the
drive to the mounting surface using all 4 screws or bolts.

June 2009
Chapter 3 — Power Wiring

Guidelines
To ensure proper wiring, use the following guidelines:
● Use heat-resistant copper cables only, +75°C or higher.
● The input line cable and line fuses must be sized in accordance with the rated input
current of the unit. See Tables 3-2 through 3-8.
● Provide a ground wire with both input power and output motor leads.
The control should be installed in accordance with all applicable codes. In accordance with
NEC 430 Part IV, a protective device is required in the installation of the control. This
protective device can be either a fuse or circuit breaker. An RK fuse is an acceptable
component. For maximum protection Eaton recommends a Class T fuse.
Input line cable and line fuses must be sized in accordance with Tables 3-2 through 3-6.
● If the motor temperature sensing is used for overload protection, the output cable size
may be selected based on the motor specifications.
● If three or more shielded cables are used in parallel for the output on the larger units,
every cable must have its own overload protection.
● Avoid placing the motor cables in long parallel lines with other cables.
● If the motor cables run in parallel with other cables, note the minimum distances
between the motor cables and other cables given in Table 3-1 below:
Table 3-1: Cable Spacings
Minimum Distance Between
Cables in Feet (m) Cable in Feet (m)
1 (0.3) ≤ 164 (50)

3.3 (1.0) ≤ 656 (200)
● The spacings of Table 3-1 also apply between the motor cables and signal cables of
other systems.
● The maximum length of the motor cables is as follows:
– 1 – 2 hp, 230V units, 328 ft. (100m)
– All other hp units, 984 ft. (300m)
● The motor cables should cross other cables at an angle of 90 degrees.
● If conduit is being used for wiring, use separate conduits for the input power wiring,
the output power wiring, the signal wiring and the control wiring.

June 2009
UL Compatible Cable Selection and Installation

Use only copper wire with temperature rating of at least 75°C.
Table 3-2: 40°C Cable and Fuse Sizes — 230V Ratings
Wire Size Terminal Size
Frame Fuse Fuse
IL hp Size NEC I [A] I [A] Quantity [A] Power Ground Power Ground
1 FR4 4.2 4.8 3 10 14 14 16 – 12 16 – 14

1-1/2 6 6.6 3 10 14 14 16 – 12 16 – 14
2 6.8 7.8 3 10 14 14 16 – 12 16 – 14
3 9.6 11 3 15 14 14 16 – 12 16 – 14
5 FR5 15.2 17.5 3 20 12 12 16 – 8 16 – 8
7-1/2 22 25 3 30 10 10 16 – 8 16 – 8
10 28 31 3 40 8 8 16 – 8 16 – 8
15 FR6 42 48 3 60 4 8 14 – 0 10 – 2
20 54 61 3 80 2 6 14 – 0 10 – 2
25 FR7 68 72 3 100 2 6 14 – 0 10 – 00
30 80 87 3 110 1 6 14 – 0 10 – 00
40 104 114 3 125 1/0 4 14 – 0 10 – 00
50 FR8 130 140 3 175 3/0 2 4 – 3/0 4 – 000
60 154 170 3 200 4/0 0 000 – 350 MCM 4 – 000
75 192 205 3 250 300 2/0 000 – 350 MCM 4 – 000
100 FR9 248 261 3 300 2x4/0 3/0 2x000 – 350 MCM 4 – 000
UL recognized type JJS preferred but RK acceptable.

June 2009

Frame Fuse Fuse
1-1/2 FR4 3 3.3 3 10 14 14 16 – 12 16 – 14

2 3.4 4.3 3 10 14 14 16 – 12 16 – 14
3 4.8 5.6 3 10 14 14 16 – 12 16 – 14
5 7.6 7.6 3 10 14 14 16 – 12 16 – 14
7-1/2 11 12 3 15 12 14 16 – 12 16 – 14
10 FR5 14 16 3 20 10 12 16 – 8 16 – 8
15 21 23 3 30 10 10 16 – 8 16 – 8
20 27 31 3 35 8 8 16 – 8 16 – 8
25 FR6 34 38 3 50 6 8 14 – 0 10 – 2
30 40 46 3 60 4 8 14 – 0 10 – 2
40 52 61 3 80 2 6 14 – 0 10 – 2
50 FR7 65 72 3 100 2 6 14 – 0 10 – 00
60 77 87 3 110 1 6 14 – 0 10 – 00
75 96 105 3 125 1/0 4 14 – 0 10 – 00
100 FR8 124 140 3 175 3/0 2 4 – 3/0 4 – 000
125 156 170 3 200 4/0 0 000 – 350 MCM 4 – 000
150 180 205 3 250 300 2/0 000 – 350 MCM 4 – 000
200 FR9 240 261 3 350 2x4/0 3/0 2x000 – 350 MCM 4 – 000
250 302 300 3 400 2x250 300 2x000 – 350 MCM 4 – 000
300 FR10 361 385 3 450 2x250 300 600 MCM 300 MCM
350 414 460 3 500 2x300 300 600 MCM 300 MCM
400 477 520 3 600 2x400 350 600 MCM 300 MCM
500 FR11 590 590 6 350 2x500 500 Bus Bar Bus Bar
550 NS 650 6 400 4x4/0 500 Bus Bar Bus Bar
600 NS 730 6 450 4x250 600 Bus Bar Bus Bar
650 FR12 NS 820 6 500 4x300 600 Bus Bar Bus Bar
800 NS 1030 6 600 4x350 Bus Bar Bus Bar
UL recognized type JJS preferred but RK acceptable.

June 2009

Frame Fuse Fuse
3 FR6 3.9 4.5 3 10 14 14 14 – 0 14 – 2

5 6.1 7.5 3 10 14 14 14 – 0 14 – 2
7-1/2 9 10 3 15 12 14 14 – 0 14 – 2
10 11 13.5 3 20 12 12 14 – 0 14 – 2
15 17 18 3 30 10 10 14 – 0 14 – 2
20 22 22 3 35 8 8 14 – 0 14 – 2
25 27 27 3 40 8 8 14 – 0 14 – 2
30 32 34 3 45 6 8 14 – 0 14 – 2
40 FR7 41 41 3 50 6 8 14 – 0 10 – 0
50 52 52 3 70 4 6 14 – 0 10 – 0
60 FR8 62 62 3 80 2 6 4 – 000 4 – 000
75 77 80 3 125 1/0 6 4 – 000 4 – 000
100 99 100 3 150 2/0 6 4 – 000 4 – 000
125 125 125 3 175 3/0 6 4 – 000 4 – 000
150 FR9 144 144 3 250 300 1/0 000 – 350 MCM 4 – 000
200 192 208 3 275 350 2/0 000 – 350 MCM 4 – 000
250 FR10 242 261 3 350 2x4/0 3/0 600 MCM 300 MCM
300 289 325 3 400 2x250 300 600 MCM 300 MCM
400 382 385 3 450 2x300 300 600 MCM 300 MCM
450 FR11 412 460 6 250 2x300 300 Bus Bar Bus Bar
500 472 502 6 300 2x350 350 Bus Bar Bus Bar
600 FR12 NS 650 6 400 4x4/0 500 Bus Bar Bus Bar
UL recognized type JJS preferred but RK acceptable
Table 3-5: Cable and Busbar Sizes, SPX FR10 – FR12 — 480V Ratings
External Power Busbars
Internal Power Cables
Frame Cu
hp Size Current Cu (per phase) (in Inches) Qty.
250 FR10 300 2 x 2/0 1.18 x 0.25 3

300 385 2 x 3/0 1.57 x 0.25 3
350 460 2 x 3/0 1.57 x 0.25 3
400 FR11 520 2 x 2 x 2/0 1.18 x 0.25 6
500 590 2 x 2 x 2/0 1.18 x 0.25 6
— 650 2 x 2 x 2/0 1.18 x 0.25 6
600 FR12 750 2 x 2 x 3/0 1.57 x 0.25 6
— 820 2 x 2 x 3/0 1.57 x 0.25 6
700 920 2 x 2 x 3/0 1.57 x 0.25 6
90°C rating recommended.

June 2009
Internal Power Connections Supply Busbars
Busbar Size/
Busbar Size Phase Cable Size/
Frame NFE – INU (Choke — NFE) Phase Cu
hp Size Current (in Inches) (in Inches) (Choke — NFE) (in Inches) Qty.
800 FR13 1030 2.36 x 0.39 1.57 x 0.25 2 x 300 MCM 1.57 x 0.25 6
900 1150 3.15 x 0.39 1.57 x 0.25 2 x 250 MCM 1.57 x 0.25 12
1000 1300 3.15 x 0.39 1.57 x 0.25 2 x 250 MCM 1.57 x 0.25 12
1200 FR14 1600 2.36 x 0.39 1.57 x 0.25 2 x 250 MCM 1.57 x 0.25 12
1600 1940 2.36 x 0.39 1.57 x 0.25 2 x 300 MCM 1.57 x 0.25 12

Rigid copper connection.
External Power Busbars
Internal Power Cables
Frame Cu
hp Size Current Cu (per phase) (in Inches) Qty.
200 FR10 208 2x2/0 1.18 x .25 3

250 261 2x2/0 1.18 x .25 3
300 325 2x2/0 1.18 x .25 3
400 FR11 385 2x3/0 1.57 x .25 3
450 460 2x3/0 1.57 x .25 3
500 502 2x2x2/0 1.18 x .25 6
— FR12 590 2x2x2/0 1.18 x .25 6
600 650 2x2x2/0 1.18 x .25 6
700 750 2\x2x2/0 1.18 x .25 6
90°C rating recommended.
Internal Power Connections Supply Busbars
Busbar Size/
Busbar Size Phase Cable Size/
Frame NFE – INU (Choke — NFE) Phase Cu
hp Size Current (in Inches) (in Inches) (Choke — NFE) (in Inches) Qty.
800 FR13 820 2.36 x 0.39 1.57 x .25 2 x 300 MCM 1.18 x .25 6
900 920 2.36 x 0.39 1.57 x .25 2 x 250 MCM 1.18 x .25 6
1000 1030 2.36 x 0.39 1.57 x .25 2 x 300 MCM 1.18 x .25 6
1350 FR14 1300 3.15 x 0.39 1.57 x .25 2 x 250 MCM 1.18 x .25 12
1500 1500 2.36 x 0.39 1.57 x .25 2 x 250 MCM 1.18 x .25 12
2000 1900 2.36 x 0.39 1.57 x .25 2 x 300 MCM 1.18 x .25 12
Rigid copper connection.
Table 3-9: Maximum Symmetrical Supply Current

Maximum RMS Symmetrical
Product Voltage Amperes on Supply Circuit
3/4 – 30 hp 230 100,000A

1-1/2 – 200 hp 480 100,000A

June 2009
UL Compatible Cable Selection and Installation with Breaker

Use only copper wire with temperature rating of at least 75°C.
Table 3-10: Cable and Breaker Sizes – 230V Ratings
Frame Breaker
hp Size FLA Current Power Ground Power Ground
1 FR4 4.8 15 14 14 12 – 16 14 – 16
1-1/2 6.6 15 14 14 12 – 16 14 – 16
2 7.8 15 14 14 12 – 16 14 – 16
3 11 15 12 12 12 – 16 14 – 16
5 FR5 17.5 20 10 10 8 – 16 8 – 16
7-1/2 25 30 8 8 8 – 16 8 – 16
10 FR6 31 40 8 8 1/0 – 14 2 – 14
15 48 60 4 6 1/0 – 14 2 – 14
20 FR7 61 80 2 6 1/0 – 14 2/0 – 10
25 72 100 2 6 1/0 – 14 2/0 – 10
30 87 100 1/0 4 1/0 – 14 2/0 – 10
Based on a maximum environment of 104°F (40°C).
A UL listed breaker must be used.

Frame Breaker
1-1/2 FR4 3.3 15 14 14 12 – 16 14 – 16

2 4.3 15 14 14 12 – 16 14 – 16
3 5.6 15 14 14 12 – 16 14 – 16
5 7.6 15 14 14 12 – 16 14 – 16
7-1/2 FR5 12 20 12 12 8 – 16 8 – 16
10 16 30 10 10 8 – 16 8 – 16
15 23 30 8 8 8 – 16 8 – 16
20 FR6 31 40 8 8 1/0 – 14 2 – 14
25 38 50 6 8 1/0 – 14 2 – 14
30 46 60 4 6 1/0 – 14 2 – 14
40 FR7 61 80 2 6 1/0 – 14 2/0 – 10
50 72 100 2 6 1/0 – 14 2/0 – 10
60 87 100 1/0 4 1/0 – 14 2/0 – 10
75 FR8 105 125 2/0 2 3/0 – 4 3/0 – 4
100 140 150 4/0 1/0 350 MCM – 3/0 3/0 – 4
125 170 200 300 2/0 350 MCM – 3/0 3/0 – 4
150 FR9 205 250 350 3/0 350 MCM – 2x3/0 3/0 – 4
200 261 300 2x250 3/0 350 MCM – 2x3/0 3/0 – 4
250 FR10 300 400 2x250 300 MCM 600 MCM 600 MCM
300 385 500 2x300 300 MCM 600 MCM 600 MCM
350 460 600 2x400 300 MCM 600 MCM 600 MCM
400 FR11 520 700 2x500 500 Bus Bar Bus Bar
500 590 800 4x4/0 500 Bus Bar Bus Bar
550 650 900 4x250 600 Bus Bar Bus Bar
650 820 1000 4x300 600 Bus Bar Bus Bar
700 920 1200 4x400 Bus Bar Bus Bar

June 2009

Frame Breaker
2 FR6 3.3 15 14 14 1/0 – 14 2 – 14

3 4.5 15 14 14 1/0 – 14 2 – 14
5 7.5 15 14 14 1/0 – 14 2 – 14
7-1/2 10 20 12 14 1/0 – 14 2 – 14
10 13.5 30 10 12 1/0 – 14 2 – 14
15 18 30 10 10 1/0 – 14 2 – 14
20 22 40 8 8 1/0 – 14 2 – 14
25 27 40 8 8 1/0 – 14 2 – 14
30 FR7 34 50 6 8 1/0 – 14 1/0 – 10
40 41 60 4 6 1/0 – 14 1/0 – 10
50 FR8 52 100 2 6 3/0 – 4 3/0 – 4
60 62 100 1 6 3/0 – 4 3/0 – 4
75 80 125 1/0 6 3/0 – 4 3/0 – 4
100 100 150 3/0 6 3/0 – 4 3/0 – 4
125 FR9 125 200 4/0 2 350 MCM – 2x3/0 3/0 – 4
150 144 250 350 1/0 350 MCM – 2x3/0 3/0 – 4
200 FR10 208 300 2x250 300 MCN 600 MCM 600 MCM
250 261 400 2x300 300 MCM 600 MCM 600 MCM
300 325 500 2x350 300 MCM 600 MCM 600 MCM
450 460 600 2x350 350 Bus Bar Bus Bar
500 502 700 2x500 500 Bus Bar Bus Bar
550 FR12 590 800 4x4/0 500 Bus Bar Bus Bar
600 650 900 4x250 600 Bus Bar Bus Bar
700 750 1000 4x300 600 Bus Bar Bus Bar
Note: The current interrupting of the breaker, up to 100 kAIC, will determine the overall
current rating of the combination.

June 2009
Table 3-13: Power Connection Tightening Torque

Frame Tightening Torque Tightening Torque
Rating Size (in-lbs) (Nm)
230V, 3/4 – 3 hp FR4 5 0.6

480V, 1 – 5 hp 5 0.6
230V, 5 – 7-1/2 hp FR5 13 1.5
480V, 7-1/2 – 15 hp 13 1.5
230V, 10 – 15 hp FR6 35 4
480V, 20 – 30 hp 35 4
575V, 2 – 25 hp 35 4
230V, 20 – 30 hp FR7 85 10
480V, 40 – 60 hp 85 10
575V, 30 – 40 hp 85 10
480V, 75 – 125 hp FR8 340/187 40/22
575V, 50 – 75 hp 340/187 40/22
480V, 150 – 200 hp FR9 340/187 40/22
575V, 100 – 175 hp 340/187 40/22
The isolation standoff of the bus bar will not withstand the listed tightening torque.
Use a wrench to apply a counter torque when tightening.
Installation Instructions
1. Strip the motor and input power cables as shown in Figure 3-1 and Table 3-14.
Ground Ground
A1 C1 A2 C2
B1 D1 B2 D2
Power Motor
Figure 3-1: Input Power and Motor Cable Stripping

and Wire Lengths

June 2009
Cable Stripping Lengths for Power and Motor Cables

Table 3-14: Power and Motor Cable Stripping Lengths
Product Power Wiring in Inches (mm) Motor Wiring in Inches (mm)
Frame
hp Voltage Size A1 B1 C1 D1 A2 B2 C2 D2
3/4 – 3 230V FR4 0.59 1.38 0.39 0.79 0.28 1.97 0.28 1.38
1–5 480V (15) (35) (10) (20) (7) (50) (7) (35)
5 – 7-1/2 230V FR5 0.79 1.57 0.39 1.18 0.79 2.36 0.39 1.57
7-1/2 – 15 480V (20) (40) (10) (30) (20) (60) (10) (40)
10 – 15 230V FR6 0.79 3.54 0.59 2.36 0.79 3.54 0.59 2.36
20 – 30 480V (20) (90) (15) (60) (20) (90) (15) (60)
2 – 25 575V
20 – 30 230V FR7 0.98 4.72 0.98 4.72 0.98 4.72 0.98 4.72
40 – 60 480V (25) (120) (25) (120) (25) (120) (25) (120)
30 – 40 575V
75 – 125 480V FR8 1.10 9.45 1.10 9.45 1.10 9.45 1.10 9.45
50 – 75 575V (28) (240) (28) (240) (28) (240) (28) (240)
150 – 200 480V FR9 1.10 11.61 1.10 11.61 1.10 11.61 1.10 11.61
100 – 300 575V (28) (295) (28) (295) (28) (295) (28) (295)
2. Locate the plastic bag containing the wiring plate.
Figure 3-2: Wiring Plate
3. If conduit is being used, attach the wiring plate to drive then conduit.
4. Pass the motor and input power wires/cables through the holes of the wiring plate.
5. Connect the input power and motor and control wires to their respective terminals
according to the wiring diagrams in the section marked “Standard Wiring Diagrams and
Terminal Locations” on Page 3-11.
6. If an optional external brake resistor is used, connect its cable to the appropriate
terminals. See “Standard Wiring Diagrams and Terminal Locations.”
7. If shielded cable is used, connect the shields of the input line power cable and the motor
cable to the ground terminals of the SVX9000/SPX9000 drive, the motor and the line
power supply.

June 2009
Figure 3-3: Ground Terminal Locations
8. If shielded cable is not used, check the connection of the ground cable to the motor, the
SVX9000/SPX9000 drive and the input line power terminals marked with .
9. Attach the wiring plate with the screws provided. Ensure that no wires are trapped
between the frame and the wiring plate.
10. Insert the rubber grommets supplied into the wiring plate holes that have not been
used, as illustrated in Figure 3-4.
Figure 3-4: Cable Protection Plate

June 2009
Standard Wiring Diagrams and Terminal Locations

The following wiring diagrams show the line and motor connections of the frequency
converter.
Power
Board
230V 3/4 - 15 hp
480V 1 - 30 hp
575V 2 - 25 hp
Control
Board
RFI Filter
L1 L2 L3 R- U V W
DC- DC+/
R+ Note:
Integrated Brake
Chopper Circuit Not
Included on 575V units.
BR
Option
L1 L2 L3
See
Note
M
3~

FR4 to FR5 and FR6
Note: When using a 1-phase supply, for units rated for such, connect the input power to
terminals L1 and L2. Consult Eaton for more information.

June 2009
Power
Board
230V 20 - 30 hp
480V 40 - 125 hp
575V 30 - 75 hp
Control
Board
RFI Filter
DC+/
L1 L2 L3 R+ R- U V W
DC-
BR
Option
Note:
Integrated Brake
Chopper Circuit Not
Included on 575V units.
L1 L2 L3
See
Note
M
3~

FR6, FR7 and FR8

June 2009
Power
Board
480V 150 - 350 hp

575V 100 - 300 hp
Control
Board
RFI Filter
DC+/
L1 L2 L3 R+ R- U V W
DC-
BR
Option
L1 L2 L3
See M
Note 3~

FR9 to FR10
The dotted lines refer to components present in FR9 but not in FR10.

June 2009
Power and Motor Wiring Terminal Photos
230V, 3/4 – 3 hp
480V, 1 – 5 hp
Frame Size: FR4
Figure 3-8: FR4 Power and Motor Wiring Terminals

June 2009
230V, 5 – 7-1/2 hp
480V, 7-1/2 – 15 hp
Frame Size: FR5

June 2009
230V, 10 – 15 hp
480V, 20 – 30 hp
575V, 2 – 25 hp
Frame Size: FR6

June 2009
230V, 20 – 30 hp
480V, 40 – 60 hp
575V, 30 – 40 hp
Frame Size: FR7

June 2009
Supplied only when

Brake Chopper
included with Drive.
{
480V, 75 – 125 hp
575V, 50 – 75 hp
Frame Size: FR8

June 2009
480V, 150 – 200 hp

575V, 100 – 175 hp
Frame Size: FR9

June 2009
Checking the Cable and Motor Insulation

1. Check the motor cable insulation as follows:
● Disconnect the motor cable from terminals U, V and W of the SVX9000/SPX9000 and
from the motor.
● Measure the insulation resistance of the motor cable between each phase conductor as
well as between each phase conductor and the protective ground conductor.
● The insulation resistance must be >1 MΩ.
2. Check the input power cable insulation as follows:
● Disconnect the input power cable from terminals L1, L2 and L3 of the SVX9000/
SPX9000 and from the utility line feeder.
● Measure the insulation resistance of the input power cable between each phase
conductor as well as between each phase conductor and the protective ground
conductor.
3. Check the motor insulation as follows:
● Disconnect the motor cable from the motor and open any bridging connections in the
motor connection box.
● Measure the insulation resistance of each motor winding. The measurement voltage
must equal at least the motor nominal voltage but not exceed 1000V.

June 2009
Chapter 4 — Control Wiring

General Information
The control unit of the SVX9000/SPX9000 consists of the control board and various option
boards that plug into the five slot connectors (A to E) of the control board.
Galvanic isolation of the control terminals is provided as follows:
● The control connections are isolated from power, and the GND terminals are
permanently connected to ground.
● The digital inputs are galvanically isolated from the I/O ground.
● The relay outputs are double-isolated from each other at 300V AC.
Option Board General Information

The SVX9000/SPX9000 series drives can accommodate a wide selection of expander and
adapter option boards to customize the drive for your application needs.
The drive’s control unit is designed to accept a total of five option boards. Option boards are
available for normal analog and digital inputs and outputs, communication and additional
application-specific hardware.
The SVX9000/SPX9000 factory installed standard option board configuration includes an A9
I/O board and an A2 relay output board, which are installed in slots A and B. For information
on additional option boards, see the 9000X Series Drives Option Board User Manual.
E
D
C
B
A
Figure 4-1: Option Board Slots

June 2009
Control Wiring Guidelines

Wire the control terminals using the following guidelines:
● The control wires shall be at least AWG 20 (0.5 mm2) shielded cables.
● The maximum wire size is AWG 14 (2.5 mm2) for the relay terminals and AWG 16
(1.5 mm2) for all other terminals.
● The tightening torques for the option board terminals are listed in Table 4-1.
Table 4-1: Tightening Torques of Terminals

Tightening Torque
Terminal Screw in-lbs Nm
Relay and thermistor terminals 4.5 0.5

(M3 screw)
Other terminals (M2.6 screw) 2.2 0.25
Control Wiring Instructions

Table 4-2: Control Wiring Instructions
1. Unlock the bottom cover by turning
the locking screw 90 degrees
counterclockwise.
2. Remove the bottom cover by rotating

the cover towards you on the base
hinges, then lifting the cover away
from the base.

June 2009
Table 4-2: Control Wiring Instructions (Continued)

3. Wire the control terminals following
the details for the specific option
boards shown on the following pages.
Note: Note for ease of access, the option

board terminal blocks can be
unplugged for wiring.
Control Wiring Details

Wiring Option Board A9
Basic I/O Board A9

+10Vref 1
Input Reference
AI1+ 2
(Voltage)
GND 3
AI2+ 4 Input Reference

(Current)
AI2- 5
24Vout 6 Control Voltage Output
GND 7
DIN1 8
DIN2 9
DIN3 24V
10
CMA GND
11
24Vout 12
GND 13
DIN4 14
DIN5 15
24V
DIN6 16
CMB GND
17
AO1+ 18 0 (4)/20 mA
AO1- 19 RL<500 8
DO1 20 + V<+48V
I<50 mA
Indicates Connections for Inverted Signals
Figure 4-2: Option Board A9 Wiring Diagram

June 2009
Table 4-3: Option Board A9 Terminal Descriptions

Terminal Signal Description and Parameter Reference
1 +10 Vref Reference voltage Maximum current 10 mA

2 AI1+ Analog input, voltage Default: 0 – +10V (Ri = 200 kΩ)
-10V to +10V (joystick control)
3 GND Analog input common
0 – 20 mA (Ri = 250 Ω)
Select V or mA with jumper block X1 (Figure 4-3)
Differential input if not connected to ground;
allows ±20V differential mode voltage to GND
4 AI2+ Analog input Default: 0 – 20 mA (Ri = 250 Ω)
0 – +10V (Ri = 200 kΩ)
5 GND/AI2- Analog input common
-10V to +10V (joystick control)
Select V or mA with jumper block X2
(Figure 4-3)
Differential input if not connected to ground;
allows ±20V differential mode voltage to GND
6 24 Vout 24V control voltage (bi-directional) ±15%, 250 mA (all boards total); 150 mA (max.
current from single board); Can be used as
external power backup for the control (and
fieldbus); Galvanically connected to terminal #12
7 GND I/O ground Ground for reference and controls; Galvanically
connected to terminals #13, 19
8 DIA1 Digital input 1 Ri = min. 5 kΩ
9 DIA2 Digital input 2
10 DIA3 Digital input 3
11 CMA Digital input common A for DIN1, Must be connected to GND or 24V of I/O terminal
DIN2 and DIN3 or to external 24V or GND. Selection with
jumper block X3. (Figure 4-3)
12 24 Vout 24V control voltage (bi-directional) Same as terminal #6; Galvanically connected to
terminal #6
13 GND I/O ground Same as terminal #7; Galvanically connected to
terminals #7 & 19
14 DIB4 Digital input 4 Ri = min. 5 kΩ
15 DIB5 Digital input 5
16 DIB6 Digital input 6
17 CMB Digital input common B for DIN4, Must be connected to GND or 24V of I/O terminal
DIN5 and DIN6 or to external 24V or GND. Select with jumper
block X3. (Figure 4-3)
18 A01+ Analog signal (+output) Output signal range: 0 – 10V default
Current: 0(4) – 20 mA, RL max 500 Ω or
Voltage: 0 – 10V, RL >1 kΩ
Selection with jumper block X6. (Figure 4-3)
19 A01- Analog output common Maximum Vin = 48V DC; Galvanically connected
to terminals #7, 13
20 DO1 Digital output1 Open collector, Maximum current = 50 mA

June 2009
X2 Jumper Setting
Analog Input 2 (AI2)
X1 Jumper Setting
0 to 20 mA* A B C D
Analog Input 1 (AI1) Current Input
0 to 10V* ABC D ABC D
0 to 10V
Voltage Input Voltage Input
0 to 20 mA ABC D 0 to 10V ABC D X6 Jumper Setting

Current Input (Differential) Analog Output 1 (A01)
Voltage Input
0 to 10V ABC D ABC D
(Differential) ABC D 0 to 20 mA
-10 to 10V
Voltage Input Current Output
Voltage Input
ABC D 0 to 10V* ABC D
-10 to 10V
Voltage Input Voltage Output
ABC D ABC D ABC D
X1 X2 X6
X3 Jumper Setting
CMA and CMB Grounding
CMB Connected to Ground*

X3
CMA Connected to Ground
CMB Isolated from Ground
CMA Isolated from Ground
CMB and CMA Internally
Connected and Isolated
from Ground
* Designates Default Jumper Settings
Figure 4-3: Option Board A9 Jumper Location and Settings
Wiring Option Board A2
Basic Relay Board A2
RO1/1 21
RO1/2 22
RL
RO1/3 23 AC / DC
RO2/1 24 Switching:
<8A / 24V DC
RO2/2 25 <0.4A / 125V DC
<8A / 250V AC
RO2/3 26 Continuously
<2 Arms
Figure 4-4: Option Board A2 Wiring Diagram

June 2009
Table 4-4: Option Board A2 Terminal Descriptions

Terminal Signal Technical Information
21 RO1/1 Normally Closed (NC) Switching Capacity:

24V DC / 8A
22 RO1/2 Common
250V AC / 8A
23 RO1/3 Normally Open (NO) 125V DC / 0.4A
Min Switching Load: 5V/10 mA
Continuous Capacity: <2 Arms
24 RO2/1 Normally Closed (NC) Switching Capacity:
24V DC / 8A
25 RO2/2 Common
250V AC / 8A
26 RO2/3 Normally Open (NO) 125V DC / 0.4A
Min Switching Load: 5V/10 mA
21 22 23
24 25 26 Continuous Capacity: <2 Arms
Figure 4-5: Option Board A2 Terminal Locations
Inverting the Digital Input Signal

The active signal level depends on which potential the common inputs CMA and CMB
(terminals 11 and 17) are connected to. The alternatives are either +24V or ground (0V). See
Figure 4-6.
The 24V control voltage and the ground for the digital inputs and the common inputs (CMA,
CMB) can be sourced from either the internal 24V supply or an external supply.
1 2
+24V Ground
DIN1 DIN1
DIN2 DIN2
DIN3 DIN3
Ground CMA +24V CMA
Figure 4-6: Positive/Negative Logic

Positive logic (+24V is the active signal) = the input is active when the switch is closed.
Negative logic (0V is the active signal) = the input is active when the switch is closed.

June 2009
Chapter 5 — Menu Information

Keypad Operation
Figure 5-1: Keypad and Display

Table 5-1: LCD Status Indicators
Indicator Description
Run
Indicates that the SVX9000/SPX9000 is running and controlling the load.
Blinks when a stop command has been given but the SVX9000/SPX9000 is
still ramping down.
Counterclockwise Operation
The output phase rotation is BAC, corresponding to counterclockwise
rotation of most motors.
Clockwise Operation
The output phase rotation is ABC, corresponding to clockwise rotation of
most motors.
Stop
Indicates that the SVX9000/SPX9000 is stopped and not controlling the load.
Ready
Indicates that the SVX9000/SPX9000 is ready to be started.
Alarm
Indicates that there is one or more active drive alarm(s).
Fault
Indicates that there is one or more active drive fault(s).
I/O Terminal
Indicates that the I/O terminals have been chosen for control.
Keypad
Indicates that the keypad has been chosen for control.
Bus/Communications
Indicates that the communications bus control has been chosen for control.

June 2009
Table 5-2: LED Status Indicators

Indicator Description
local Local — Steady Illumination

Indicates that the SVX9000/SPX9000 is ready to be started and operated from
the Local mode.
Local — Flashing
Indicates that the SVX9000/SPX9000 is ready for operating command to
select Local or Remote operation.
remote Remote
Indicates that the SVX9000/SPX9000 is operating and controlling the load
remotely.
fault Fault
Indicates that there is one or more active drive fault(s).
Table 5-3: Navigation Buttons

Button Description
Start
This button operates as the START button for normal operation when the
“Keypad” is selected as the active control.
Enter
This button is used in the parameter edit mode to save the parameter setting
and move to the next parameter …
• to reset the Fault History if pressed while in the “Fault History” menu.
• to confirm the acceptance of a change.
• to change a virtual button status while in the “Button” menu.
• to confirm the start-up list at the end of the Start-Up Wizard.
• when the “Operate” menu is active, to exit the “Operate” submenu.
Stop
This button has two integrated operations. The button operates as STOP
button during normal operation …
• motor STOP from the keypad, which is always active unless disabled by
the “StopButtonActive” parameter.
• used to reset the active faults.
Reset
Resets the active faults.
Local / Remote
Switches between LOCAL and REMOTE control for start, speed reference and
reverse functions. The control locations corresponding to local and remote
can be selected within an application.

June 2009
Table 5-3: Navigation Buttons (Continued)

Button Description
Left Arrow
• navigation button, movement to left.
• in parameter edit mode, exits mode, backs up one step.
• cancels edited parameter (exit from a parameter edit mode).
• When in “Operate” menu will move backward through menu.
• At end of “Start-Up Wizard”, repeats the “Start-Up Wizard” setup menu.
Right Arrow
• navigation button, movement to right.
• enter parameter group mode.
• enter parameter mode from group mode.
• When in “Operate” menu will move forward through menu.
Up and Down Arrows
• move either up or down a menu list to select the desired menu item.
• editing a parameter/password, while the active digit/character is scrolled.
• increase/decrease the reference value of the selected parameter.
• in the “Operate” menu, will cause the display of the current reference
source and value and allow its change if the keypad is the active
reference source. Used to set the password (if defined) when leaving
the “Operate” menu.
• scroll through the “Active Faults” menu when the SVX9000/SPX9000 is
stopped.
Menu Navigation
Navigation Tips
● To navigate within one level of a menu, use the up and down arrows.
● To move deeper into the menu structure and back out, use the right and left arrows.
● To edit a parameter, navigate to show that parameter’s value, and press the right arrow
button to enter the edit mode. In edit mode, the parameter value will flash.
● When in edit mode, the parameter value can be changed by pressing the up or down
arrow keys.
● When in edit mode, pressing the right arrow a second time will allow you to edit the
parameter value digit by digit.
● To confirm the parameter change you must press the ENTER button. The value will not
change unless the ENTER button is pushed.
● Some parameters can not be changed while the SVX9000/SPX9000 is running. The
screen will display LOCKED if you attempt to edit these parameters while the drive is
running. Stop the drive to edit these parameters. See the appropriate application
manual for identification of these parameters specific to your chosen application.
Main Menu
The data on the control keypad are arranged in menus and submenus. The first menu level
consists of M1 to M8 and is called the Main Menu. The structure of these menus and their
submenus is illustrated in Figure 5-2. Some of the submenus will vary for each application
choice.

June 2009
+ M1 Parameters
G1.1
...
G1.x
+ M2 Keypad Control
R2.1 Keypad Reference
P2.2 Keypad Direction
...
P2.x Stop Button Active
+ M3 Active Faults
A3.1 Active Fault 1
T3.1.1 Operation Days
Menu Navigation: ...
T3.1.13 Zero Speed
Up Arrow — The up arrow ...
advances to the next A3.x Active Fault x
menu item.
For example, pressing the + M4 Fault History
up arrow once will H4.1 Most Recent Fault
advance from M1 to M2. T4.1.1 Operation Days
...
Down Arrow — The down T4.1.13 Zero Speed
arrow backs up to the ...
previous menu item. H4.1.x Oldest Saved Fault
For example, pressing the + M5 System Menu
down arrow once will back S5.1 Language
up from M2 to M1. S5.2 Application
S5.3 Copy Parameters
Right Arrow — The right
S5.4 Compare Parameters
arrow will advance to the
S5.5 Security
next level in the menu.
S5.6 Keypad Settings
For example, pressing the
S5.7 Hardware Settings
right arrow once will
S5.8 System Information
advance from M2 to R2.1.
+ M6 Expander Boards
Left Arrow — The left G6.1 Slot A Board
arrow will back up one ...
level in the menu G6.5 Slot E Board
structure.
For example, pressing the
+ M7 Monitor
left arrow once will back V7.1 Output Frequency - 0.00 Hz
up from R2.1 to M2. V7.2 Frequency Reference - 0.00 Hz
...
M7.1x Multimonitor
N7.1x.1
+ M8 Operate Mode
O1 Output Frequency - 0.0 Hz
O2 Freq Reference - 0.0 Hz
...
Ox . . .
Figure 5-2: Main Menu Navigation

Menu application dependent.

June 2009
Parameter Menu (M1)

The Parameter Menu is a single or multi-level menu dependent upon the application in use,
arranged by the parameter group items. Figure 5-3 illustrates this for the Standard
application. Parameters and parameter groups are explained in further detail in the
appropriate application manual.
M1 Parameters Menu
+ G1.1 Basic Parameters
P1.1.1 Minimum Frequency
P1.1.2 Maximum Frequency
...
P1.1.16 Preset Speed 1
+ G1.2 Input Signals
P1.2.1 Start/Stop Logic
P1.2.2 DIN3 Function
...
P1.2.9 AI2 Signal Select
+ G1.3 Output Signals
P1.3.1 A1out Signal
P1.3.2 A1out Content
...
P1.3.17 A2out Scale
+ G1.4 Drive Control
P1.4.1 Ramp 1 Shape
P1.4.2 Ramp 2 Shape
...
P1.4.13 Flux Brake Current
+ G1.5 Skip Frequency
P1.5.1 Skip F1 Low Limit
P1.5.2 Skip F1 High Limit
P1.5.3 PH Accel/Decel Ramp
+ G1.6 Motor Control
P1.6.1 Motor Control Mode
P1.6.2 V/Hz Optimization
...
P1.6.13 Identification
+ G1.7 Protections
P1.7.1 4mA Input Fault
P1.7.2 4mA Fault Frequency
...
P1.7.23 Slot Comm Fault Response
+ G1.8 Auto Restart
P1.8.1 Wait Time
P1.8.2 Trial Time
...
P1.8.10 Underload Tries
Figure 5-3: Parameter Menu Structure Example

June 2009
Keypad Control Menu (M2)

In the Keypad Control Menu, you can set the frequency reference, choose the motor
direction for keypad operation, and determine if the STOP button will be active at all
times. See Figure 5-4.
M2 Keypad Control
R2.1 Keypad Reference
P2.2 Keypad Direction
...
P2.x Stop Button Active
Figure 5-4: Keypad Control Menu
R2.1 Range: Min. Frequency — Max. Frequency

Keypad Units: Hertz
Reference Keypad Reference
This displays and allows the operator to edit the keypad frequency reference. A
change takes place immediately. This reference value will not influence the output
frequency unless the keypad has been selected as the active control place.
P2.2 Range: Forward, Reverse Default: Forward

Keypad Keypad Direction
Direction This allows the operator to change the rotation direction of the motor. This setting
will not influence the rotation direction of the motor unless the keypad has been
selected as the active control place.
P2.3 Range: Yes, No Default: Yes

Stop Button StopButtonActive
Active By default, pushing the STOP button will always stop the motor regardless of the
selected control place. If this parameter is set to No, the STOP button will stop the
motor only when the keypad has been selected as the active control place.
This parameter number varies for different applications.

June 2009
Active Faults Menu (M3)

When a fault occurs, the SVX9000/SPX9000 stops. The sequence indication F1, the fault code,
a short description of the fault and the fault type symbol will appear on the display. In
addition, the indication FAULT or ALARM is displayed and, in case of a FAULT, the red LED on
the keypad starts to blink. If several faults occur simultaneously, the sequence of active faults
can be browsed with the Browser buttons. See Figure 5-5.
The active faults memory can store the maximum of 10 faults in the sequential order of
appearance. The fault remains active until it is cleared with either the STOP or RESET buttons
or with a reset signal from the I/O terminal. Upon fault reset the display will be cleared and
will return to the same state it was before the fault trip.
51 Ext Fault
F T1 T13
Figure 5-5: Active Fault Display Example
CAUTION
Remove any External Start signals or permissives before resetting
the fault to prevent an unintentional restart of the SVX9000/
SPX9000, which could result in personal injury or equipment
damage.

June 2009
Fault Type Range: A, F, AR, FT

Fault Type
There are four different types of faults. These faults and their definitions are given in
Table 5-4.
Table 5-4: Fault Types

Fault
Type Fault Name Description
A Alarm This type of fault is a sign of an unusual operating

condition. It does not cause the drive to stop, nor does it
require any special actions. The “A fault” remains in the
display for about 30 seconds.
F Fault An “F fault” is a kind of fault that makes the drive stop.
Actions need to be taken in order to restart the drive.
AR Auto-Restart If an “AR fault” occurs the drive will also stop
Fault immediately. The fault is reset automatically and the drive
tries to restart the motor. If the restart is not successful, a
fault trip (FT) occurs.
FT Fault Trip If the drive is unable to restart the motor after an AR fault,
an FT fault occurs. The effect of the “FT fault” is the same
as that of the F fault — the drive is stopped.
Fault Code Range: 1 – 54

Fault codes indicate the cause of the fault. A list of fault codes, their descriptions,
and possible solutions can be found in Appendix B — Fault and Warning Codes.
Fault Time Range: T.1 – T.13

Data Record In this menu, important data recorded at the time the fault is available. This feature
is intended to help the user or the service person to determine the cause of fault.
Table 5-5 indicates the information that is recorded.
Table 5-5: Fault Time Data

Data Units Description
T.1 D Counted operation days (Fault 43: Additional code)

T.2 hh:mm:ss Counted operation hours
(d) (Fault 43: Counted operation days)
T.3 Hz Output frequency
hh:mm:ss (Fault 43: Counted operation hours)
T.4 A Motor current
T.5 V Motor voltage
T.6 % Motor power
T.7 % Motor torque
T.8 V DC bus voltage
T.9 °C Unit temperature
T.10 — Run status
T.11 — Direction
T.12 — Warnings
T.13 — Zero speed
Real time record.
If real time is set, T.1 and T.2 will appear as follows:
T.1 yyyy-mm-dd Counted operation days (Fault 43: Additional code)
T.2 hh:mm:ss.sss Counted operation hours (Fault 43: Counted operation days)

June 2009
Fault History Menu (M4)

All faults are stored in the Fault History Menu, which can be viewed by using the Browser
buttons. Additionally, the Fault time data record pages are accessible for each fault as in the
Active Faults Menu described above. See Figure 5-6.
The SVX9000/SPX9000’s memory can store a maximum of 30 faults, in the order of
appearance. If there are 30 uncleared faults in the memory, the next occurring fault will erase
the oldest fault from the memory.
11 Output Phase
F T1 T13
Figure 5-6: Sample Fault History Display
Note: Pressing the ENTER button for 3 seconds will clear the entire fault history.

June 2009
System Menu (M5)

The controls associated with the general use of the drive, such as application selection,
customized parameter sets or information about the hardware and software are located in
the System Menu. Password protection can be activated by parameter S5.5.1.
Descriptions of the system menu parameters are illustrated in Figure 5-7.
+ S5.1 Language Selection

+ S5.2 Application Selection
+ S5.3 Copy Parameters
S5.3.1 Parameter Sets
S5.3.2 Upload to Keypad
S5.3.3 Download from Keypad
S5.3.4 Automate Backup
S5.4 Parameter Comparison
+ S5.5 Security
S5.5.1 Password
P5.5.2 Parameter Lock
P5.5.3 Start-Up Wizard
P5.5.4 Multimonitor Items
+ S5.6 Keypad Settings
P5.6.1 Default Page
P5.6.2 Default Page/Operating Menu
P5.6.3 Timeout Time
P5.6.4 Contrast Adjustment
P5.6.5 Backlight Time
+ S5.7 Hardware Settings
P5.7.1 Internal Brake Resistor
P5.7.2 Fan Control
P5.7.3 HMI Acknowledge Timeout
P5.7.4 HMI Number of Retries
+ S5.8 System Information
+ S5.8.1 Total Counters
C5.8.1.1 MWh Counter
C5.8.1.2 Power On Day Counter
C5.8.1.3 Power On Hour Counter
+ S5.8.2 Trip Counters
T5.8.2.1 MWh Counter
T5.8.2.2 Clear MWh Trip Counter
T5.8.2.3 Power On Day Counter
T5.8.2.4 Power On Hour Counter
T5.8.2.5 Clear Operating Time Counter
+ S5.8.3 Software Information
I5.8.3.1 Software Package
I5.8.3.2 System Software Version
I5.8.3.3 Firmware Interface
I5.8.3.4 System Load
+ S5.8.4 Applications
A5.8.4.# Name of Application
D5.8.4.#.1 Application ID
D5.8.4.#.2 Version
D5.8.4.#.3 Firmware Interface
+ S5.8.5 Hardware
I5.8.5.1 Nominal Unit Power
I5.8.5.2 Nominal Unit Voltage
E5.8.5.3 Brake Chopper
E5.8.5.4 Brake Resistor
+ S5.8.6 Expander Boards
+ S5.8.7 Debug Menu
Figure 5-7: System Menu Structure

June 2009
System Menu Parameters
S5.1 Range: English, Spanish, French, Portuguese Default: English

Language Language
Selection This parameter offers the ability to control the SVX9000/SPX9000 through the
keypad in the language of your choice. Available languages are: English, Spanish,
French and Portuguese.
S5.2 Default: Basic

Application Application
Selection This parameter sets the active application.
When changing applications, you will be asked if you want the parameters of the
new application to be uploaded to the keypad. If you wish to load the new
application parameters, push the ENTER button. Pushing any other button saves the
parameters of the previously used application in the keypad.
System Menu Copy Parameter Options (S5.3)

The parameter copy function is used when the operator wants to copy one or all parameter
groups from one drive to another. All the parameter groups are first uploaded to the keypad,
then the keypad is connected to another drive and then the parameter groups are
downloaded to it (or possibly back to the same drive).
Note: Before any parameters can successfully be copied from one drive to another, the drive
must be stopped when the parameters are downloaded to it.
S5.3.1
Parameter Parameter Sets
Sets This parameter allows you to reload the factory default parameter values, and to
store and load two customized parameter sets.
S5.3.2
Upload to Up to keypad
Keypad This function uploads all existing parameter groups to the keypad.
S5.3.3 Range: 0 – 3 Default: 0 (All parameters)

Download Down from keypad
from Keypad This function downloads one or all parameter groups from the keypad to the drive.
0 All parameters
1 All, no motor
2 Application parameters
S5.3.4 Range: Yes, No Default: Yes

Automatic Auto.backup
Backup This parameter activates and deactivates the parameter backup function. When the
Parameter backup function is activated, the keypad makes a copy of the parameters
and settings in the currently active application. When applications are changed, you
will be asked if you wish the parameters of the new application to be uploaded to
the keypad. For this to happen, push the ENTER button. If you wish to keep the copy
of the parameters of the previously used application saved in the keypad push any
other button.
Note: Parameters saved in the parameter settings of S5.3.1 will be deleted when
applications are changed. If you want to transfer the parameters from one
application to another you have to upload them to the keypad first.

June 2009
System Menu Parameter Comparison Options (S5.4)
S5.4
Parameter Parameter Comparison
Comparison With the Parameter Comparison function, you can compare the actual parameter
values to the values of your customized parameter sets and those loaded to the
control keypad.
The actual parameter values are first compared to those of the customized
parameter Set1. If no differences are detected, a “0” is displayed on the lowermost
line of the keypad.
If any of the parameter values differ from those of the Set1 parameters, the number of
the deviations is displayed together with symbol P (e.g. P1 ➔ P5 = five deviating values).
By pressing the right arrow button once again you will see both the actual value and
the value it was compared to. In this display, the value on the Description line (in the
middle) is the default value, and the one on the value line (lowermost line) is the
edited value. You can also edit the actual value by pushing the Right Arrow button.
Actual values can also be compared to Set2, Factory Settings and the Keypad Set values.
Security Menu Parameter Options (S5.5)

Note: The Security submenu is protected with a password. Store the password in a safe place.
S5.5.1 Range: 0 – 65535 Default: 0

Password Password
The application selection can be protected against unauthorized changes with the
Password function. When the password function is enabled, the user will be
prompted to enter a password before application changes, parameter value
changes, or password changes.
By default, the password function is not in use. If you want to activate the password,
change the value of this parameter to any number between 1 and 65535. The
password will be activated after the Timeout time (Timeout Time) has expired.
To deactivate the password, reset the parameter value to 0.
P5.5.2 Range: ChangeEnable, ChangeDisabl Default: ChangeDisabl

Parameter Parameter Lock
Lock This function allows the user to prohibit changes to the parameters. If the parameter
lock is activated the text *locked* will appear on the display if you try to edit a
parameter value.
Note: This function does not prevent unauthorized editing of parameter values.
P5.5.3 Range: Yes, No Default: No

Start-Up Start-up Wizard
Wizard The Start-Up Wizard facilitates commissioning the SVX9000/SPX9000. If selected
active, the Start-Up Wizard prompts the operator for the language and application
desired and then advances through the start-up parameter list. After completion it
allows the user to repeat the Start-Up Wizard or return to the default page, the
Operate Menu. The Start-Up Wizard in always active for the initial power up of the
SVX9000/SPX9000.
P5.5.4 Range: ChangeEnable, ChangeDisabl Default: ChangeEnable

Multimonitor Multimon.items
Items The keypad display can display three actual monitored values at the same time. This
parameter determines if the operator is allowed to replace the values being
monitored with other values.

June 2009
Keypad Settings (S5.6)

There are five parameters (Default Page to Backlight Time) associated with the keypad
operation:
P5.6.1 Default: 0
Default Page Default page
This parameter sets the view to which the display automatically moves as the
Timeout Time expires or when the keypad power is switched on. If the Default Page
value is 0 this function is not activated, i.e. the last displayed page remains on the
keypad display.
P5.6.2
Default Page Default page/OM
in the Here you can set the location in the Operating menu to which the display
Operating automatically moves as the set Timeout Time expires, or when the keypad power is
Menu switched on. See setting of Default Page parameter above.
P5.6.3 Range: 0 – 65,535 Default: 30

Timeout Time Units: Seconds
Timeout time
The Timeout Time setting defines the time after which the keypad display returns to
the Default Page.
Note: If the Default Page value is 0 the Timeout Time setting has no effect.
P5.6.4
Contrast Contrast adjustment
Adjustment If the display is not clear, you can adjust the keypad contrast with this parameter.
P5.6.5 Range: 1 – 65,535 or Forever Default: 10

Backlight Units: Minutes
Time Backlight time
This parameter determines how long the backlight stays on before going out. You
can select any time between 1 and 65,535 minutes or “Forever”.

June 2009
Hardware Settings (S5.7)

The Hardware Settings submenu (S5.7) provides parameters for setting information on
Internal brake resistor connection, Fan control, Keypad acknowledge timeout and Keypad
retries.
P5.7.1 Range: Connected – Not Connected Default: Connected

Internal Brake Internbrakeres
Resistor With this function you tell the SVX9000/SPX9000 whether the internal brake resistor
Connection is connected or not.
If your drive has an internal brake resistor, the default value of this parameter is
“Connected”. However, if it is necessary to increase braking capacity by installing an
external brake resistor, or if the internal brake resistor is disconnected, it is advisable
to change the value of this function to “Not Connected” in order to avoid
unnecessary fault trips.
Note: The brake resistor is available as an option for all drives. It can be installed
internally in frame sizes FR4 to FR6.
5.7.2 Range: Continuous, Temperature, First Start and Default: Continuous

Fan Control Calc Temp
Fan Control
This function allows you to control the SVX9000/SPX9000’s cooling fan. You can set
the fan to run:
1 Continuous — fan runs continuously.
2 Temperature — based on the temperature of the unit. The fan is switched on
automatically when the heatsink temperature reaches 60°C. The fan receives a
stop command when the heatsink temperture falls to 55°C. The fan runs for
about a minute after receiving the stop command or switching on the power, as
well as after changing the value from “Continuous” to “Temperature”.
3 First Start — after power up the fan is stopped until the run command is given
and then fan runs continuously. This is mainly made for common DC-bus
systems to prevent cooling fans to load charging resistors on power up moment.
4 Calc Temp — starting of cooling fan is based on calculated IGBT-temperature.
When IGBT temp = 40°C, fan starts and when temp falls down to 30°C, fan stops.
Note: The fan runs continuously, regardless of this setting, when the SVX9000/
SPX9000 is in RUN state.

June 2009
P5.7.3 Range: 200 – 5,000 Default: 200

Keypad Units: mseconds
Acknowledge Keypad ACK timeout
Timeout This function allows the user to change the timeout of the Keypad
acknowledgement time.
Note: If the SVX9000/SPX9000 has been connected to a PC with a serial cable, the
default values of Keypad Acknowledge Timeout and Number of Retries to Receive
Keypad Acknowledgement must not be changed.
If the SVX9000/SPX9000 has been connected to a PC via a modem and there is delay
in transferring messages, the value of Keypad Acknowledge Timeout must be set
according to the delay as follows:
Example:
• Transfer delay between the SVX9000/SPX9000 and the PC is found to be = 600 ms
• The value of Keypad Acknowledge Timeout is set to 1200 ms (2 x 600, sending
delay + receiving delay)
• The corresponding setting is then entered in the [Misc] section of the file
9000XDrive.ini:
Retries = 5
AckTimeOut = 1200
TimeOut = 5000
It must also be considered that intervals shorter than the Keypad Acknowledge
Timeout time cannot be used in SVX9000/SPX9000 drive monitoring.
P5.7.4 Range: 1 – 10 Default: 5

Number of Keypad retry
Retries to With this parameter you can set the number of times the drive will try to receive an
Receive acknowledgement when it has not been received within the acknowledgement time
Keypad (Keypad Acknowledge Timeout) or if the received acknowledgement is faulty.
Acknowledge-
ment
System Information (S5.8)

This section contains hardware and software information as well as operation information.
S5.8.1
Total Total counters
Counters In the Total Counters page you will find information related to the SVX9000/
SPX9000 operating times, i.e. the total numbers of MWh, operating days and
operating hours. See Table 5-6.
Unlike the counters for the Trip Counters, these counters cannot be reset.
Note: The Power On time counters, days and hours, operate whenever power is
applied to the SVX9000/SPX9000.
Table 5-6: Total Counters

Number Name Description
C5.8.1.1 MWh counter Megawatt hours total operation time counter

C5.8.1.2 Power On day Number of days the SVX9000/SPX9000 has been
counter supplied with power
C5.8.1.3 Power On hour Number of hours the SVX9000/SPX9000 has been
counter supplied with power

June 2009
S5.8.2
Trip Counters Trip counters
The Trip Counters are counters whose values can be reset to zero. The resettable
counters are shown in Table 5-7.
Table 5-7: Trip Counters

T5.8.2.1 MWh counter Megawatts hours since last reset
P5.8.2.2 Clear MWh Resets megawatts hours counter
counter
T5.8.2.3 Power On day Number of days the SVX9000/SPX9000 has been run
counter since the last reset
T5.8.2.4 Power On hour Number of hours the SVX9000/SPX9000 has been run
counter since the last reset
P5.8.2.5 Clr Optime cntr Resets the operating day and hour counters
Note: The Trip Counters operate only when the motor is running.
S5.8.3
Software Software
Information The Software information page includes information on the following software
related topics:
Table 5-8: Software Information

I5.8.3.1 Software SVX00031V003
package
I5.8.3.2 System 11.53.6536
software
version
I5.8.3.3 Firmware 4.37
interface
I5.8.3.4 System load G9.1
S5.8.4
Application Applications
Information The Application information page includes information on not only the application
currently in use but also all other applications loaded into the SVX9000/SPX9000.
The information available is shown in Table 5-9. Note that the “x” in the table refers
to the sequential number of the application in the list.
Table 5-9: Application Information

Name Content
A4.8.4.x Application name
D4.8.4.x.1 Application ID
D4.8.4.x.2 Version
D4.8.4.x.3 Firmware interface

June 2009
S5.8.5
Hardware Hardware
Information The Hardware information page provides information on the following hardware-
related topics:
Table 5-10: Hardware Information

Number Content
I5.8.5.1 Nominal power of the unit
I5.8.5.2 Nominal voltage of the unit
E5.8.5.3 Brake chopper
E5.8.5.4 Brake resistor
S5.8.6
Expander Expander boards
Board This parameter and its sub-items provide information about the basic and option
Information boards plugged into the control board as shown in Table 5-11. Note that the “x” in
the table refers to the sequential number of the slot, with slot A being “1” and slot
E being “5”.
Table 5-11: Expander Board Information

Number Content
E5.8.6.x Slot “x” board identification
E5.8.6.x.1 Operating state
E5.8.6.x.2 Software version
S5.8.7
Debug Menu Debug
This menu is meant for advanced users and application designers. Contact the
factory for any assistance needed.

June 2009
Expander Board Menu (M6)

The Expander Board Menu makes it possible for the user to:
● to see what expander boards are connected to the control board and
● to access and edit the parameters associated with the expander board.
+ G6.1 “A: OPTA9” (Slot A Option Board)

G6.1.1 Parameters
P6.1.1.1 AI1 Mode
P6.1.1.2 AI2 Mode
P6.1.1.3 AO1 Mode
G6.1.2 I/O-monitor
+ G6.2 “B: ” (Slot B Option Board)

+ G6.3 “C: ” (Slot C Option Board)
+ G6.4 “D: ” (Slot D Option Board)
+ G6.5 “E: ” (Slot E Option Board)
Figure 5-8: Expander Board Menu Structure
Example of Expander Board Parameters for Option Board A9
P6.1.1.1 Range: 1 – 5 Default: 3

AI1 Mode AI1 Mode
Analog Input 1 input options:
1 0 – 20 mA
2 4 – 20 mA
3 0 – 10V
4 2 – 10V
5 -10 – +10VP

AI2 Mode AI2 Mode
Analog Input 2 input options:
1 0 – 20 mA
2 4 – 20 mA
3 0 – 10V
4 2 – 10V
5 -10 – +10VP

AO1 Mode A01 Mode
Analog Output 1 output options:
1 0 – 20 mA
2 4 – 20 mA
3 0 – 10V
4 2 – 10V

June 2009
Monitoring Menu (M7)

The Monitoring Menu items are meant for viewing parameter values during operation.
Monitored values are updated every 0.3 sec. Monitored items are identified by item numbers
V7.1 to V1.xx, where “xx” varies by application. Table 5-12 provides an example of the
monitored values for the Standard application.
Monitored parameters are not editable from this menu (See Parameter Menu [M1] to change
parameter values).
Table 5-12: Monitoring Menu Items — Standard Application Example
Code Signal Name Unit Description
V7.1 Output Frequency Hz Output frequency
V7.2 Frequency reference Hz Frequency reference setting
V7.3 Motor speed rpm Calculated motor speed
V7.4 Motor current A Measured motor current
V7.5 Motor torque % Calculated torque based on nominal motor torque
V7.6 Motor power % Calculated power based on nominal motor power
V7.7 Motor voltage V Calculated motor voltage
V7.8 DC bus voltage V Measured DC-bus voltage
V7.9 Unit temperature °C Heatsink temperature
V7.10 Calculated motor °C Calculated motor temperature based on the motor
temperature nameplate information and the calculated motor load
V7.11 Analog Input 1 V Voltage input at Terminals AI1+ and GND
V7.12 Analog Input 2 mA Current input at Terminals AI2+ and AI2-
V7.13 DIN1, DIN2, DIN3 — Digital input status (Figure 5-9)
V7.14 DIN4, DIN5,DIN6 — Digital input status (Figure 5-10)
V7.15 DO1, RO2, RO3 — Digital and relay output status (Figure 5-11)
V7.16 Analog Iout mA Current output at Terminals AO1+ and AO1-
V1.13
DIN1, DIN2, DIN3
OFF ON OFF
Figure 5-9: Digital Inputs — DIN1, DIN2, DIN3 Status
V1.14
DIN4, DIN5, DIN6
ON OFF OFF
Figure 5-10: Digital Inputs — DIN4, DIN5, DIN6 Status
V1.15
DO1, RO1, RO2
OFF OFF ON
Figure 5-11: Digital and Relay Outputs — DO1, RO1, RO2 Status

June 2009
Multimonitor (V7.17)
This parameter allows the viewing and selection (if allowed by System menu item, P5.5.4) of
three simultaneously monitored items from the Monitored Menu Items shown in Table 5-12.
Use the right arrow key to select the item to be modified and then the up or down arrow keys
to select the new item. Press the ENTER key to accept the change.
Operate Menu (M8)

The Operate Menu provides a easy to use method of viewing key numerical Monitoring
Menu items. Some applications also support the setting of reference values in this menu. The
items displayed vary by application. Table 5-13 is an example for the Standard application.
Table 5-13: Operate Menu Items — Standard Application Example
Code Signal Name Unit Description
O.1 Output Frequency Hz Output frequency
O.2 FreqReference Hz Frequency reference
O.3 Motor Speed rpm Calculated motor speed
O.4 Motor Current A Measured motor current
O.5 Motor Torque % Calculated torque based on nominal motor torque
O.6 Motor Power % Calculated power based on nominal motor power
O.7 Motor Voltage V Calculated motor voltage
O.8 DC-Bus Voltage V Measured DC-bus voltage
O.9 Unit Temperature °C Heatsink temperature
O.10 MotorTemperature % Calculated motor temperature based on the motor
nameplate information and the calculated motor load
R1 Keypad Reference Hz Keypad frequency reference setting
The menu is navigated by using the left and right arrow buttons. If a reference level is
available for setting, the up and down arrow buttons adjust the value. To exit the Operate
Menu to access the other menus, depress the ENTER button for 2 seconds. While in the other
menus, if there is no keypad activity, the display will return to the Operate Menu after 30
seconds. Figure 5-12 illustrates the Operate Menu button function.

June 2009
One Touch Operate Menu

Navigation Note!
Up and Down arrows are defaulted to
Freq Ref Up frequency reference. Some applications
also support other references like
Torque or PID. The active reference is
Monitor Display Monitor Display selected with a parameter.
Navigation Left Navigation Right
Freq Ref Down
Display will automatically

Password ? Programming Menu
return to default Operate
M1 Parameters Menu monitor display
M2 Keypad Control after 30 sec. delay.
Exit Operate Menu by navigating M3 Active Faults
to Programming display and M4 Fault History
pressing ENTER button or simply
press ENTER button 2 seconds. M5 System Menu
Acknowledgement password M6 Expander Boards
value if defined. M7 Monitor
Return to Operate or time delay
Figure 5-12: Operate Menu Navigation
Start-Up Wizard
Upon initial power up, the Start-Up Wizard guides the commissioner through the basic
SVX9000/SPX9000 setup. The Start-Up Wizard may be set to function upon an application
change by setting parameter P5.5.3.
Upon power up, the display will read:
“Startup Wizard”
“Press enter”
Upon pressing ENTER, the choice for the language to be used followed by the application
desired are presented. The lists are navigated by using the right arrow and up and down
arrow buttons. A selection is confirmed by pressing ENTER. After these two selections, the
following text appears:
“Setup starts”
“Press enter”
When ENTER is pressed the setup parameter list is presented. The parameter value will be
blinking allowing setting by the arrow buttons. The value is confirmed using the ENTER
button, after which the next parameter in the list will be displayed.
After the last setup parameter is presented, the following text is displayed:
“Repeat setup?”
“Press ➔“
If the left arrow is pressed the Start-Up Wizard restarts. If the ENTER button is pressed the
following is displayed:
“Setup done”
After this, the display returns to the default page, normally the Operate Menu.

June 2009

June 2009
Chapter 6 — Start-Up
Safety Precautions
Before start-up, observe the warnings and safety instructions provided throughout this
manual.
WARNING
1 Internal components and circuit boards (except the isolated
I/O terminals) are at utility potential when the SVX9000/
SPX9000 is connected to the line. This voltage is extremely
dangerous and may cause death or severe injury if you
come in contact with it.
2 When the SVX9000/SPX9000 is connected to the utility, the

motor connections U (T1), V (T2), W (T3) and DC-bus/brake
resistor connections B–, B+ and R– are live even if the motor
is not running.
3 Do not make any connections when the AF drive is

connected to the utility line.
4 Do not open the cover of the AF drive immediately after

disconnecting power to the unit, because components
within the drive remain at a dangerous voltage potential for
some time. Wait at least five minutes after the cooling fan
has stopped and the keypad or cover indicators are dark
before opening the SVX9000/SPX9000 cover.
5 The control I/O terminals are isolated from the utility

potential, but relay outputs and other I/Os may have
dangerous external voltages connected even if power is
disconnected from the SVX9000/SPX9000.
6 Before connecting to the utility, make sure that the cover of

the drive is closed.

June 2009
Overview
The SVX9000/SPX9000 Control can be used to operate induction motors using the
applications included in the system software delivered with the drive. Higher performance
permanent magnet (PM) synchronous motors and other functions of the frequency converter
(FC) are accomplished by loading special applications with the 9000XLoad software tool. The
following sections describe how to commission the drive for motor control in all applications.
See the All-in-One or special application manual for additional startup information or details
on the parameters. Parameters are available (visible) based on the application selected, the
type of control (SVX or SPX), the option boards installed in the control and the version of the
system software loaded in the control. In general, the SVX controls are limited to V/Hz and
open loop speed control of induction motors while the SPX control will work with any
application and option board. Before starting the commissioning process, select the type of
control, option boards, and size of the drive to meet the needs of the application and check
that the latest system software is loaded. Open loop or sensorless control means motor
control is accomplished by the standard drive unit without added speed/position feedback
devices and associated option cards. Vector control means the drive can differentiate
between torque producing and magnetizing current when reading motor phase currents. The
“rotor flux oriented, current vector control” allows the AC drive to control an induction motor
in the same manner as a separately excited DC motor.
Open Loop Vector Control Operations

The SVX9000/SPX9000 Control normally operates an induction motor in V/Hz or open loop
vector control (speed control) mode. By default, the ID run is designed to automatically
configure parameters for the programmable volts per Hertz (V/f) curve and make a stator
resistance measurement for a standard induction motor. If the ID run does not give the
proper performance, manual tuning of the control is described in later sections.
Frequency Controlled Application

For pumps and fans the application is usually frequency controlled and there is no need for
high torque on low speed. A straight V/f curve (“linear” V/Hz ratio type) is all that is required
for proper operation. Since pumps and fans are variable torque, selecting “Squared” for
V/Hz ratio type will give some energy savings. Compensation for measured stator resistance
voltage drop will improve performance and selecting “Auto Torque Boost” will help start the
motor if necessary. The SLX/SVX controls will operate a PM motor open loop but manual
tuning of the V/f curve is required.
Speed Controlled Application

When an application is speed controlled and high torque at low speed is needed, it is often
necessary to complete the ID run; select auto torque boost to help start the motor and set the
drive to speed control mode to compensate for the slip of the induction motor.

June 2009
Closed Loop Vector Control Operations

Closed loop vector mode provides the best performance for speed and torque control;
especially in low speed, high torque applications, including full torque at zero speed. The
SPX is required for closed loop control with a speed or position feedback device. The closed
loop ID run is similar to the open loop mode ID run.
PM Motor Control Operations

The SPX control can be used to control a synchronous PM motor open loop, or closed loop
with a resolver or absolute encoder. Best low speed, high torque performance is achieved
with a position feedback device. The High Performance Multi-purpose application has a
selection for PM motor control. The PM motor Encoder ID run determines the zero position of
the rotor and stores it to a parameter for use when the load is connected.
Sequence of Operation to Commission an Induction Motor

1. Read and follow all safety warnings and cautions in this manual.
2. At installation ensure:
● That the SVX9000/SPX9000 and motor are connected to ground.
● That the utility and motor cables are in accordance with the installation and
connection instructions as detailed in Chapter 3 — Power Wiring.
● That the control cables are located as far as possible from the power cables as
detailed in Chapter 4 — Control Wiring and Table 3-1. That control cable shields are
connected to protective ground. That no wires make contact with any electrical
components in the SVX9000/SPX9000.
● That the common input of each digital input group is connected to ground or +24V of
the I/O terminal supply or an external supply as detailed here and Figure 4-6.
3. Check the quality of the cooling air as detailed in Chapter 2 — Mounting.
4. Check that moisture has not condensed inside the SVX9000/SPX9000.
5. Check that all START/STOP switches connected to the I/O terminals are in the STOP
state.
6. Connect the SVX9000/SPX9000 to the utility and switch the power on. For the initial
power up you will enter the Start-Up Wizard, which will guide you through application
selection and basic parameter setup. See the Start-Up Wizard section at the end of
Chapter 5 — Menu Information for more information. After completing the Start-Up
Wizard, proceed to step 8. If this is not the initial power up, the keypad will default to the
Operate Menu. Depress the ENTER button for 2 seconds to enter the Parameter Menu.
Proceed to step 7.

June 2009
7. Ensure that the Group 1 parameters match the application by setting — at minimum, the
following parameters to match the motor nameplate:
● Nominal voltage of the motor.
● Nominal nameplate frequency of the motor.
● Nominal nameplate full load speed of the motor.
● Motor nominal current.
● Motor power factor.
● Motor type (Select PM motor in Group 6 of special app)
8. Perform either Test A or Test B without the motor connected to the SVX9000/SPX9000.
Test A — Control from the Control Panel
● Apply input power to the SVX9000/SPX9000.
● Press the keypad START button.
● If not in the Operate Menu, go to the Monitoring Menu and check that the output
frequency follows the keypad reference.
● Press the keypad STOP button.
Test B — Control from the I/O Terminals
● Apply input supply power to the SVX9000/SPX9000.
● Change control from the keypad to the I/O terminals using the LOCAL/REMOTE
button.
● Start the drive by closing the START/STOP input on DIN1.
● Change the frequency reference setting on AI1.
● If not in the Operate Menu, go to the Monitoring Menu and check that the output
frequency follows the frequency reference.
● Stop the drive by opening the START/STOP input on DIN1.
9. Disconnect all power to the SVX9000/SPX9000. Wait until the cooling fan on the unit
stops and the indicators on the panel are not lit. If no keypad is present, check the
indicators in the control panel cover. Wait at least five more minutes for the DC bus to
discharge. Connect the motor to the SVX9000/SPX9000. If possible, perform a startup
test or ID run with the motor connected to the SVX9000/SPX9000 but not connected to
the process. If the SVX9000 must be tested with the motor connected to the process,
perform it under no-load conditions.

June 2009
10. Repeat test 8A or 8B to check operation of the motor without the process or load. Note
for proper motor current, voltage and direction of shaft rotation. If an encoder card is
installed, set encoder parameters in the expander board menu and monitor frequency
and speed from the encoder board. Frequency should match output frequency of the
drive with a positive value for forward direction. If encoder frequency is opposite;
change motor phase order, encoder connection or select “invert” on the expander
board menu. For many pump or fan applications, no tuning is required. If further tuning
is necessary, perform the tuning while the motor is disconnected from the process.
11. Perform ID Run. Setting the identification parameter to the appropriate value Par/group
P1.6.16 followed by a start command within 20 seconds activates automatic
identification. (See test 8A or 8B for start command.) Upon completion, cancellation by
a stop command or if timely start is not received, the parameter will reset to its default
setting. Possible ID run selections are as follows:
● OL V/f Ratio — The drive is run at zero speed to identify the motor parameters.
(Earlier system software version.)
● OL V/f +Boost — The drive is run at zero speed to identify the motor parameters and
automatic torque boost is turned on. (Earlier system software version.)
● Identification without motor run — The drive is run at zero speed to identify the
motor parameters.
● Identification with motor run — The drive is run at 2/3 rated speed to identify the
motor parameters. (No load on motor.)
● Encoder ID run — Identifies the shaft zero position when using PM motor with
absolute encoder or resolver feedback.
12. When ID Run is complete as shown by a stop indication on the keypad, reset the drive
with a stop command according to Test 8A or 8B. Set the motor control mode to
OL Speed Control, CL Speed Control if appropriate for the application and repeat
Test 8A or 8B.
13. If necessary, skip to the next section to perform manual tuning functions before
connecting the motor to the process.
14. Disconnect all power to the SVX9000/SPX9000. Wait until the cooling fan on the unit
stops and the indicators on the panel are not lit. If no keypad is present, check the
indicators in the control panel cover. Wait at least five more minutes for the DC bus to
discharge. Connect the motor to the driven load making sure mechanical system
requirements are met. Make sure that the driven load can be run safely and that no
hazard exists to any personnel. Repeat test 8A or 8B.

June 2009
Manual Tuning of the SVX9000/SPX9000

Proper tuning of the open loop speed control will give better torque control accuracy for
improved motor performance. The aim of tuning is to get the motor model as close to the
actual motor as possible through proper setting of parameters. Open loop tuning consists of
three functions, 1) V/f curve tuning, 2) stator resistance measurement, and 3) compensation
for slip.
Voltage at Field VN
Weakening Point
Programmable
V/f
Curve Midpoint
Voltage
Linear
Output Voltage
at Zero Frequency
f
U/f fN
Curve Midpoint Field Weakening
Frequency Point
Figure 6-1: Open Loop Tuning

June 2009
V/f- Curve Manual Tuning

When tuning the V/f — curve manually (not using identification run) the motor shaft must be
unloaded and the motor control mode set to frequency control (P1.6.1). The following
parameters are adjusted to tune the V/f curve:
Parameters
V/f ratio selection P1.6.3
Field weakening point P1.6.4
Voltage at field weakening point P1.6.5
V/f curve midpoint frequency P1.6.6
V/f curve midpoint voltage P1.6.7
Output voltage at zero frequency P1.6.8
When using a linear V/f curve with increased zero frequency voltage ensure that the motor
current does not increase too much between 3 – 7 Hz.
Tuning Steps
Set the motor nameplate values.
Nominal voltage of motor P1.1.6
Nominal frequency of motor P1.1.7
Nominal speed of motor P1.1.8
Nominal current of motor P1.1.9
Motor Power Factor (Cos Phi) P1.1.10
Run the motor unloaded at 2/3 rated speed using a frequency reference. Read the motor
current from the monitoring menu (V7.4) or use 9000XDrive for monitoring. This current is
the motor magnetizing current. This value should match a nameplate magnetizing current
value if given.
If the motor will only be run in closed loop, skip to section on closed loop vector control
tuning.
Change the V/f- curve ratio selection to programmable-mode = 2 (P1.6.3).
Run motor with zero frequency reference and increase motor zero point voltage (P1.6.8) until
motor current is approximately same as the motor magnetizing current. (If motor is only in
the low frequency area for short periods, it is possible to use up to 80% of rated current).
Set then the midpoint voltage (P1.6.7) to 1.4142*P1.6.8 ( 2 * Zero Point Voltage) and
midpoint frequency (P1.6.6) to value P1.6.8/100%*P1.1.7. ([ZeroPoint Voltage/100%]*Nominal
frequency of motor.)
P1.6.8
P1.6.7 = 2 * P1.6.8 P1.6.6 = ---------------- * P1.1.7
100

June 2009
Hint for the 9000X Drive user:

When zero point voltage is set correctly, run motor with slow ramp (~20 s) to 1/2 of rated
frequency. Show output frequency and motor current in the 9000XDrive monitoring window.
If midpoint parameters are set correctly, motor current should be stable during acceleration.
(Picture 2: heavy solid line).
If there is a peak in the monitored motor current, (heavy dashed in picture 2.) check what the
output frequency is at the max current point, and set this value for midpoint frequency
(P1.6.6). Then readjust midpoint voltage for a stable current performance during
acceleration.
ld
V/f Midpoint
Voltage P1.6.7
Practical Compromise
Ideal
With Linear V/f
V/f Midpoint
Frequency P1.6.6
2...3 x Slip Freq.
1 Hz
Figure 6-2: Motor Current after V/f-Curve Tuning

June 2009
Stator Resistance Measurement Using Dc-brake at Start

1. Define the DC-brake current (=motor nominal current) (P1.4.8).
2. Set the DC-brake time at start to 2 seconds (P1.4.11).
3. Give start command.
The drive will correct the stator impedance to improve the motor torque calculation. This also
improves slip compensation accuracy. (Stator resistance voltage loss compensation, see
picture 3.)
If the DC-brake time at start is set back to zero, the calculated stator impedance value goes
back to default if the drive's power is switched off. (Identification will retain all values in
memory.)
Voltage Loss on = R x I
S S
Stator Resistance
Is Iq
RS Id
RR
V Across LM Is Air
V at the
The Magnetizing LM Gap
Motor Terminals
Voltage Flux
~V
Stator Rotor
Figure 6-3: Motor Equivalent Circuit
Change the motor control mode to the speed control (P1.6.1 = 1)

Change the V/f-optimization (Auto Torque Boost) to on if more torque is needed on low
frequencies (P1.6.2). Note, this will increase motor voltage while loading motor, check motor
current draw.
Note: In high torque — low speed applications — it is likely that the motor will overheat. If the
motor has to run a prolonged time under these conditions, special attention must be
paid to cooling the motor.

June 2009
Slip Compensation In Open Loop

The drive uses motor torque and motor nominal RPM to compensate slip. If motor nominal
RPM is 1710 -> nominal slip is 90 RPM. And when motor torque is 50% slip is 45 RPM. To
keep reference speed drive must increase output frequency by:
50%*90 RPM
------------------------------------ * 50,00 Hz = 1,50 Hz
1500 RPM
TN TN
1/2 1/2
Slip Slip
Figure 6-4: Left: OL Speed Control Off. Right: OL Speed Control ON.

June 2009
Closed Loop Vector Control Manual Tuning (SPX9000 Only)

For some non-standard motors the auto-tune is not sufficient. Closed lop control mode is
used, when enhanced performance near zero speed and better steady stats and dynamic
speed accuracy at higher speeds are needed.
Tuning Steps
Set the motor nameplate values.
Nominal voltage of motor P1.1.6
Nominal frequency of motor P1.1.7
Nominal speed of motor P1.1.8
Nominal current of motor P1.1.9
Motor Power Factor (Cos Phi) P1.1.10
Check encoder Pulse/Revolution rate and set this value to expander menu P6.3.1.1.
Parameter is only visible if OPTA4 or OPTA5 is installed to slot C.
Set motor control mode to open loop frequency control (P1.6.1 = 0).
Run the motor unloaded at 2/3 rated speed using a frequency reference. Read the motor
current from the monitoring menu (V1.4) or use 9000X Drive for monitoring. This current is
the motor magnetizing current. This value should match a nameplate magnetizing current
value if given.
Check the expander board menu (monitoring page V6.3.2.1), that the encoder frequency is
approximately the same as the output frequency. Check also, that the direction is correct. If
the encoder frequency direction is opposite the output frequency (negative value), change
the motor phase order to encoder connection. The expander board menu also has a
parameter to invert the signal if rewiring is not an option.
Set motor control mode to closed loop (P1.6.1 = 3 or 4).
Set the motor magnetizing current P1.6.17.1 (measured in step 4).
Fine Tuning
Tune parameter P1.6.17.6 (Slip Adjust) to get the motor voltage slightly above the linear
V/f-curve when motor is loaded and slightly below when motor is generating.
Using the linear V/f-curve (P1.6.3 = 0), run the motor in frequency control mode (P1.6.1 = 0) at
about 2/3 of the motor nominal frequency and check motor voltage (V7.7).
At 40 Hz, voltage should be 40/60*460V = 307V.
Run the motor in closed loop control mode with same reference and check the motor voltage.
Adjust P1.6.17.6 (Slip Adjust) so that motor voltage is slightly above the linear
V/f-curve. If motor voltage is low, decrease the value of Slip Adjust (P1.6.17.6).

June 2009
307 V Closed Loop

Motor Voltage
60 Hz
460V
40 Hz
Figure 6-5: Closed Loop Motor Voltage
Adjust the following parameters for optimum performance in closed loop mode:
Fine Tuning Parameters
613 Speed control P gain

Sets the gain for the speed controller in % per Hz. 100 means nominal torque with 1 Hz
frequency error.
614 Speed control I time

Sets the integral time constant for the speed controller. Too short integration time
makes the control unstable.
620 Load drooping

Setting a proper value to the LoadDrooping parameter enables the load drooping.
This function causes the speed to decrease as the load torque increases. At rapid load
changes this gives a smoother torque response, when a part of the required power is
taken from the system inertia. This operation causes a constant, torque-dependent
steady-state error in speed response.
626 Acceleration compensation

Sets the inertia compensation to improve speed response during acceleration and
deceleration. The time is defined as acceleration time to nominal speed with nominal
torque. This parameter is active also in advanced open loop mode.
627 Magnetizing current at start
628 Magnetizing time at start

These parameters are certain type of DC-brake in start. With these parameters it is
possible to shorten the time needed to fully magnetize the motor, especially when
motor is big.

June 2009
615 Zero speed time at start

After giving the start command the drive will remain at zero speed for the time
defined by this parameter. The ramp is released to follow the set frequency/speed
reference after this time has elapsed.
616 Zero speed time at stop

The drive will remain at zero speed with controllers active for the time defined by this
parameter after reaching the zero speed when a stop command is given. This
parameter has no effect, if the selected stop function (P1.4.7) is coasting.
621 Start-up torque

This parameter selects the start-up torque.
Torque Memory is used in crane applications. Start-up Torque FWD/REV can be used
in other applications to help the speed controller.
0 = Not Used
1 = TorqMemory
2 = Torque Ref
3 = Torq.Fwd/Rev
633 Start-up torque, forward

Sets the start-up torque for forward direction, if selected with par. 1.6.17.12.
634 Start-up torque, reverse

Sets the start-up torque for reverse direction, if selected with par. 1.6.17.13.
107 Current limit

This parameter determines the maximum motor current from the frequency
converter. The parameter value range differs from size to size. On closed loop control
mode this limits torque (= torque producing current).
For example, if motor magnetizing current is 2.0 A and current limit is 1.0 A, total
motor current can be:
I (Total Current)
Iq (Torq. Producing Current) = 1.0 A
Id (Magnetising Current) = 2.0 A
I2 = ld2 + lq2
I = 2.24 A
I= ld2 + lq2
Figure 6-6: Closed Loop Current Limit

June 2009

June 2009
Appendix A — Technical Data

General
Figure A-1 shows a block diagram of the SVX9000/SPX9000 drive. The SVX9000/SPX9000
physically consists of two sections, the Power Unit and the Control Unit. The three-phase
AC Choke with the DC-Link Capacitor form a LC filter which together with the Rectifier
produce the DC voltage for the IGBT Inverter block. The AC Choke smooths the disturbances
from the utility into the SVX9000/SPX9000 as well as the high frequency disturbances caused
by the SVX9000/SPX9000 on the utility line. It also improves the input current waveform to
the SVX9000/SPX9000. The IGBT Inverter produces a symmetrical three-phase pulse width
modulated adjustable frequency AC voltage to the motor.
The Motor and Application Control block contains a microprocessor with customized
software. The microprocessor controls the motor based on Measured Signals, parameter
value settings and commands from the Control I/O Block and the Control Module. The Motor
and Application Control block commands the Motor Control ASIC which calculates the IGBT
switching positions. Gate Drivers amplify these signals for driving the IGBT Inverter.
The Control Keypad is a link between the user and the SVX9000/SPX9000. With the Control
Keypad the user can set parameter values, read status information and issue control
commands. The Control Keypad is removable and can be mounted externally and connected
with the appropriate cable. Instead of the Control Keypad, a PC can be used to control the
SVX9000/SPX9000 by cable connecting it where the Control Keypad is normally connected or
through an option board.
The Control I/O Block is isolated from line potential and may be connected to or isolated
from ground by the choice of the control I/O board which is used. OPTA8 is isolated ground,
OPTA1 and OPTA9 are not.
Input and Output EMC-Filters are not required for the functionality of the SVX9000/SPX9000.
They are only needed for compliance with the EU EMC directive as detailed in the following
section.
MN04001004E For more information visit: www.eaton.com A-1

June 2009
Power Brake Resistor

Module
Brake
Chopper
IGBT
Utility AC Choke Rectifier Inverter Current Motor
Sensors
3~
L1 Input U Output
L2 V
L3 EMC W EMC
Charg Res 3~
Fan
Power Measure-
Supply ments
PE Voltage
Sensors
Gate
Drivers
Control
Keypad
Motor and Motor
Application Control
RS-232
Control ASIC
Control
Module
Control Control Control Control Control

I/O I/O I/O I/O I/O
Figure A-1: SVX9000/SPX9000 Block Diagram

Specifications
Table A-1: SVX9000/SPX9000 Drive Specifications
Description Specification
Power Connections
Input Voltage (Vin) 208 – 240V +10%/-15%
380 – 500V +10%/-15%
525 – 690V +10%/-15%
Input Frequency (fin) 50/60 Hz (variation up to 45 – 66 Hz)
Connection to Utility Power Once per minute or less (typical operation)
Maximum Symmetrical Supply 208 – 240V, 100 kAIC
Current 380 – 500V, 100 kAIC
525 – 690V, 100 kAIC
Motor Connections
Output Voltage 0 to Vin
Continuous Output Current Ambient temperature max. +122°F (+50°C), overload 1.5 x IL
(1 min. out of 10 min.)
Starting Current 200% for 2 seconds
Output Frequency 0 to 320 Hz
Frequency Resolution 0.01 Hz
A-2 For more information visit: www.eaton.com MN04001004E

June 2009
Table A-1: SVX9000/SPX9000 Drive Specifications (Continued)

Control Characteristics
Control Method SVX Frequency Control (V/f)
SVX Open Loop Sensorless Vector
SPX Open Loop Sensorless Vector Control
SPX Closed Loop Control
Switching Frequency Adjustable with Parameter 2.6.9
208 – 230V: 3/4 – 15 hp: 1 to 16 kHz; default 10 kHz
20 – 30 hp: 1 to 10 kHz; default 3.6 kHz
380 – 500V: 1 – 30 hp: 1 to 16 kHz; default 10 kHz
40 – 200 hp: 1 to 10 kHz; default 3.6 kHz
525 – 690V All Sizes: 1 to 6 kHz; default 1.5 kHz
Frequency Reference Analog Input: Resolution 0.1% (10-bit), accuracy ±1%
Panel Reference: Resolution 0.01 Hz
Field Weakening Point 30 to 320 Hz
Acceleration Time 0.1 to 3000 sec.
Deceleration Time 0.1 to 3000 sec.
Braking Torque DC brake: 15% to 150% x Tn (without brake option)
Environment
Ambient Operating Temperature 14°F (-10°C), no frost to 122°F (+50°C)
Storage Temperature -40°F (-40°C) to 158°F (70°C)
Relative Humidity 0 to 95% RH, non-condensing, non-corrosive, no dripping water
Air Quality Chemical vapors: IEC 60721-3-3, unit in operation, class 3C2
Mechanical particles: IEC 60721-3-3, unit in operation, class 3S2
Altitude 100% load capacity (no derating) up to 3300 ft. (1000m);
1% derating for each 330 ft. (100m) above 3300 ft. (1000m);
max. 10000 ft. (3000m)
Vibration EN 50178, EN 60068-2-6
5 to 50 Hz, displacement amplitude 1 mm (peak) at 3 to 15.8 Hz,
Max. acceleration amplitude 1 G at 15.8 to 150 Hz
Shock EN 50178, EN 60068-2-27
UPS Drop test (for applicable UPS weights)
Storage and shipping: max. 15 G, 11 mS (in package)
Enclosure Class NEMA 1/IP21 available all ratings
NEMA 12/IP54 available all ratings
Standards
EMC (at default settings) Immunity: Fulfils all EMC immunity requirements
Emissions: EN 61800-3
Safety UL 508C
Product IEC 61800-2
Control Connections
Analog Input Voltage 0 to 10V, R – 200 kΩ differential (-10 to 10V joystick control)
Resolution 0.1%; accuracy ±1%
Analog Input Current 0(4) to 20 mA; Ri – 250Ω differential
Digital Inputs (6) Positive or negative logic; 18 to 24V DC
Auxiliary Voltage +24V ±15%, max. 250 mA
Output Reference Voltage +10V +3%, max. load 10 mA

June 2009
Table A-1: SVX9000/SPX9000 Drive Specifications (Continued)

Control Connections (Continued)
Analog Output 0(4) to 20 mA; RL max. 500Ω; Resolution 10 bit; Accuracy ±2% or 0 to
10 V, RL 1 kΩ, select with jumper
Digital Outputs Open collector output, 50 mA/48V
Relay Outputs 3 programmable change-over relay outputs
Switching capacity: 24V DC / 8A, 250V AC / 8A, 125V DC / 0.4A
Minimum switching load: 5V/10 mA
Continuous capacity: < 2 Arms
Protections
Overcurrent Protection Yes
Undervoltage Protection Yes
Ground (Earth) Fault In case of a ground fault in the motor or motor cables, only the
SVX9000/SPX9000 is protected
Input Phase Supervision Trips if any of the input phases are missing
Motor Phase Supervision Trips if any of the output phases are missing
Overtemperature Protection Yes
Motor Overload Protection Yes
Motor Stall Protection Yes
Motor Underload Protection Yes
Short Circuit Protection of the Yes
+24V and +10V Reference
Voltages
Power Ratings
Table A-2: Output Power Ratings — 230V IH
Three-Phase Input
Frame
Catalog Number Size Horsepower Current
SVXF07Ax-2A_1 FR4 3/4 3.7

SVX001Ax-2A_1 1 4.8
SVXF15Ax-2A_1 1-1/2 6.6
SVX002Ax-2A_1 2 7.8
SVX003Ax-2A_1 3 11.0
SVX005Ax-2A_1 FR5 5 17.5
SVX007Ax-2A_1 7-1/2 25.
SVX010Ax-2A_1 FR6 10 31.
SVX015Ax-2A_1 15 48.
SVX020Ax-2A_1 FR7 20 61.
SVX025Ax-2A_1 25 75.
SVX030Ax-2A_1 30 88.
Insert a 1 for NEMA Type 1 or a 2 for NEMA Type 12 in place of the x in the
Catalog Number.
For SPX drives change SVX prefix to SPX.

June 2009

Three-Phase Input
Frame
SVX001x-4A_1 FR4 1 2.2

SVXF15x-4A_1 1-1/2 3.3
SVX002x-4A_1 2 4.3
SVX003x-4A_1 3 5.6
SVX005x-4A_1 5 7.6
SVX007x-4A_1 FR5 7-1/2 12.
SVX010x-4A_1 10 16.
SVX015x-4A_1 15 23.
SVX020x-4A_1 FR6 20 31.
SVX025x-4A_1 25 38.
SVX030x-4A_1 30 46.
SVX040x-4A_1 FR7 40 61.
SVX050x-4A_1 50 72.
SVX060x-4A_1 60 87.
SVX075x-4A_1 FR8 75 105.
SVX100x-4A_1 100 140.
SVX125x-4A_1 125 170.
SVX150x-4A_1 FR9 150 205.
SVX200x-4A_1 200 245.
Insert a 1 for NEMA Type 1 or a 2 for NEMA Type 12 in place of the x in the
Catalog Number.
Table A-4: Output Power Ratings — 480V SPX FR10 – FR14

Catalog Frame Current Current
Number Size hp (IH) (IH) hp (IL) (IL)
SPX250A0-4A2N1 FR10 250 330 300 385

SPX300A0-4A2N1 300 385 — 460
SPX350A0-4A2N1 350 460 400 520
SPX400A0-4A2N1 FR11 400 520 500 590
SPX500A0-4A2N1 500 590 — 650
SPX550A0-4A2N1 — 650 600 730
SPX600A0-4A2N1 FR12 600 730 — 820
SPX650A0-4A2N1 — 820 700 920
SPX700A0-4A2N1 700 920 800 1030
SPX800A0-4A2N1 FR13 800 1030 900 1150
SPX900A0-4A2N1 900 1150 1000 1300
SPXH10A0-4A2N1 1000 1300 1200 1450
SPXH12A0-4A2N1 FR14 1200 1600 1500 1770
SPXH16A0-4A2N1 1600 1940 1800 2150
SPXH19A0-4A2N1 1900 2300 2200 2700
FR10 – FR14 includes 3% line reactor, but it is not integral to chassis.

June 2009

Three-Phase Input
Frame
SVX002A1-5A4N1 FR6 2 3.33

SVX003A1-5A4N1 3 4.5
SVX004A1-5A4N1 — 5.5
SVX005A1-5A4N1 5 7.5
SVX007A1-5A4N1 7-1/2 10.
SVX010A1-5A4N1 10 13.5
SVX015A1-5A4N1 15 18.
SVX020A1-5A4N1 20 22.
SVX025A1-5A4N1 25 27.
SVX030A1-5A4N1 FR7 30 34.
SVX040A1-5A4N1 40 41.
SVX050A1-5A4N1 FR8 50 52.
SVX060A1-5A4N1 60 62.
SVX075A1-5A4N1 75 80.
SVX100A1-5A4N1 FR9 100 100.
SVX125A1-5A4N1 125 125.
SVX150A1-5A4N1 150 144.
SVX175A1-5A4N1 — 170.
Table A-6: Output Power Ratings — 575V SPX FR10 – FR14

Catalog Frame Current Current
Number Size hp (IH) (IH) hp (IL) (IL)
SPX200A0-5A2N1 FR10 200 208 250 261

SPX250A0-5A2N1 250 261 300 325
SPX300A0-5A2N1 300 325 400 385
SPX400A0-5A2N1 FR11 400 385 450 460
SPX450A0-5A2N1 450 460 500 502
SPX500A0-5A2N1 500 502 — 590
SPX550A0-5A2N1 FR12 — 590 600 650
SPX600A0-5A2N1 600 650 700 750
SPX700A0-5A2N1 700 750 800 820
SPX800A0-5A2N1 FR13 800 820 900 920
SPX900A0-5A2N1 900 920 1000 1030
SPXH10A0-5A2N1 1000 1030 1250 1180
SPXH13A0-5A2N1 FR14 1350 1300 1500 1500
SPXH15A0-5A2N1 1500 1500 2000 1900
SPXH20A0-5A2N1 2000 1900 2300 2250
FR10 – FR14 includes a 3% line reactor but it is not integral to chassis.

June 2009
Power Loss and Switching Frequency

In some situations it may be desirable to change the switching frequency of the SVX9000/
SPX9000 for some reason (typically e.g. to reduce the motor noise). Raising the switching
frequency above the factory default level increases the drive power loss and increases the
cooling requirements, Figures A-2 through A-7 illustrate the power loss increase for the
different SVX9000/SPX9000 models. When operating above the default switching frequency
the SVX9000/SPX9000 output current rating should be derated by the ratio of the increased
power loss to the nominal power loss.
Example:
The user of a 30 hp IH, 61A, 480V SVX9000/SPX9000 wishes to increase the switching
frequency from the factory default value of 10 kHz to 15 kHz to reduce motor noise. From
Figure A-4 the loss at the factory default switching frequency of 10 kHz is 1240 watts. The loss
at 15 kHz from Figure A-4 is 1340 watts.
Re rate = 61 x 1240 = 56A

1340
Thus at the increased switching frequency the maximum load allowed is reduced to 56A to
avoid overheating the SVX9000/SPX9000.
200,00
180,00
160,00
140,00
120,00
P [W] 100,00
80,00
60,00
40,00
0003SVX 400V 0009SVX 400V
20,00 0004SVX 400V 0007SVX 400V
0005SVX 400V 0012SVX 400V
0,00
0,00 2,00 4,00 6,00 8,00 10,00 12,00 14,00 16,00
Switching Frequency [kHz]

3/4 – 3 hp 230V, 1 – 5 hp 480V

June 2009
900,00
800,00
700,00
600,00
500,00
P [W]
400,00
300,00
200,00
0016SVX 400V 0022SVX 500V
100,00 0016SVX 500V 0031SVX 400V
0022SVX 400V 0031SVX 500V
0,00
0,00 2,00 4,00 6,00 8,00 10,00 12,00 14,00 16,00

5 – 7-1/2 hp 230V, 7-1/2 – 15 hp 480V
1400,00
1200,00
1000,00
800,00
P [W]
600,00
400,00
200,00 0038SVX 400V 0045SVX 500V

0038SVX 500V 0061SVX 400V
0045SVX 400V 0061SVX 500V
0,00
0,00 2,00 4,00 6,00 8,00 10,00 12,00 14,00 16,00

10 – 15 hp 230V, 20 – 30 hp 480V

June 2009
2500,00
2000,00
1500,00
P [W]
1000,00
500,00
0072SVX 400V 0087SVX 500V
0072SVX 500V 0105SVX 400V
0087SVX 400V 0105SVX 500V
0,00
0,00 2,00 4,00 6,00 8,00 10,00 12,00

20 – 30 hp 230V, 40 – 60 hp 480V
4000,00
3500,00
3000,00
2500,00
P [W] 2000,00
1500,00
1000,00
0140SVX 400V 0168SVX 500V

500,00
0140SVX 500V 0205SVX 400V
0168SVX 400V 0205SVX 500V
0,00
0,00 2,00 4,00 6,00 8,00 10,00 12,00

75 – 125 hp 480V

June 2009
4000,00
3500,00
3000,00
2500,00
P [W] 2000,00
1500,00
1000,00
0261SVX 400V 0300SVX 400V

500,00
0261SVX 500V 0300SVX 500V
0,00
0,00 2,00 3,60 6,00 10,00

150 – 200 hp 480V

June 2009
Dimensions
D2
D3
W1
W2 R2 D1
R1
H1
H3
H2
R2
Figure A-8: NEMA Type 1 Enclosure Dimensions
Table A-7: NEMA Type 1/Type 12 Enclosure Dimensions

Frame Approximate Dimensions in Inches (mm) Weight
Size Voltage hp (IH) H1 H2 H3 D1 D2 D3 W1 W2 R1 dia. R2 dia. Lbs. (kg)
FR4 230V 3/4 – 3 12.9 12.3 11.5 7.5 2.5 5.0 5.0 3.9 0.5 0.3 11
480V 1–5 (327) (312) (292) (190) (64) (126) (128) (100) (13) (7) (5)
FR5 230V 5 – 7-1/2 16.5 16.0 15.3 8.4 2.7 5.8 5.6 3.9 0.5 0.3 17.9
480V 7-1/2 – 15 (419) (406) (389) (214) (68) (148) (143) (100) (13) (7) (8.1)
FR6 230V 10 – 15 22.0 21.3 20.4 9.3 2.7 6.7 7.7 5.8 0.7 0.4 40.8
480V 20 – 30 (558) (541) (519) (237) (68) (171) (195) (148) (18) (9) (18.5)
575V 2 – 25
FR7 230V 20 – 30 24.8 24.2 23.3 10.1 2.7 7.5 9.3 7.5 0.7 0.4 77.2
480V 40 – 60 (630) (614) (591) (257) (68) (189) (237) (190) (18) (9) (35)
575V 30 – 40
FR8 480V 75 – 125 29.7 28.8 28.4 12.3 1.3 11.0 11.2 10.0 0.7 0.4 127.8
575V 50 – 75 (755) (732) (721) (312) (34) (279) (285) (255) (18) (9) (58)
FR9 480V 150 – 200 45.3 44.1 45.3 14.3 5.4 8.8 18.9 15.7 0.7 0.4 321.9
575V 100 – 150 (1150) (1120) (1150) (362) (137) (224) (480) (400) (18) (9) (146)

June 2009
W2
Dia.
H2
H1
W1
H4
D1
H5
D2
H3
Figure A-9: NEMA Type 1 and 12 with Flange Kit, FR4, FR5 and FR6 Enclosure Dimensions
Table A-8: FR4, FR5 and FR6 with Flange Kit Enclosure Dimensions
Frame Approximate Dimensions in Inches (mm)
Size Voltage W1 W2 H1 H2 H3 H4 H5 D1 D2 Dia.
FR4 230V 5.0 4.45 13.27 12.8 12.9 1.18 .87 7.5 3.0 .27
480V (128) (113) (337) (325) (327) (30) (22) (190) (77) (7)
FR5 230V 5.67 4.7 17.0 16.5 16.5 1.4 .7 8.42 3.93 .27
480V (144) (120) (434) (420) (419) (36) (18) (214) (100) (7)
FR6 230V 7.67 6.7 22.0 21.6 21.9 1.18 .79 9.33 4.17 .25
480V (195) (170) (560) (549) (558) (30) (20) (237) (106) (6.5)
575V

June 2009
H6 H4 H4 H5 Dia.
W4 W2
H2
H1
W3
H7 W1
D1
D2
H3
Figure A-10: NEMA Type 1 with Flange Kit, FR7 and FR8 Enclosure Dimensions
Table A-9: FR7 and FR8 with Flange Kit Enclosure Dimensions
Size Voltage W1 W2 W3 W4 H1 H2 H3 H4 H5 H6 H7 D1 D2 Dia.
FR7 230V 9.33 6.8 10.62 10 25.6 24.8 24.8 7.42 7.42 .9 .78 10.1 4.6 .25
480V (237) (175) (270) (253) (652) (632) (630) (188.5) (188.5) (23) (20) (257) (117) (5.5)
575V
FR8 480V 11.22 — 13.97 13 32.75 — 29.33 10.15 10.43 1.7 2.24 11.3 4.33 .35
575V (285) (355) (330) (832) (745) (258) (265) (43) (57) (288) (110) (9)

June 2009
Dia.
D1 D2
H6 H4 H3 W4
B- B+ /R+ R-
W5
W1 W3 W2
W5
PE
D3 H2 H5
H1
Figure A-11: FR9 Enclosure Dimensions
Table A-10: FR9 Enclosure Dimensions

Size Voltage W1 W2 W3 W4 W5 H1 H2 H3 H4 H5 H6 D1 D2 D3 Dia.
FR9 480V 18.8 15.75 6.5 .35 2.12 45.27 44 28.3 8 .62 7.4 14.25 13.38 11.22 .82
575V (480) (400) (165) (9) (54) (1150) (1120) (721) (205) (16) (188) (362) (340) (285) (21)
Brake resistor terminal box (H6) included when brake chopper ordered.

June 2009
Dia.
D1
D2
D3
H4 H2 H4
H5 H3 H3 H3 H5
H7
W5
W4
W3
Opening W2 W1
W4
H6 H1 Opening
Figure A-12: FR9 with Flange Kit Enclosure Dimensions
Table A-11: FR9 with Flange Kit Enclosure Dimensions

Size Voltage W1 W2 W3 W4 W5 H1 H2 H3 H4 H5 H6 H7 D1 D2 D3 Dia.
FR9 480V 20.9 20 19.1 7.9 .22 51.7 45.3 16.5 3.9 1.4 .35 .08 24.9 13.4 4.3 .8
575V (530) (510) (485) (200) (5.5) (1312) (1150) (420) (100) (35) (9) (2) (362) (340) (109) (21)

June 2009
Power Unit — SPX9000 FR10 – FR14
H3
H5 H4
W3
W2 W5 W1
H7 H6 W4
H2
H1
D1
D2
D3 D4
Figure A-13: SPX9000 Dimensions, FR10 Open Chassis
Table A-12: Dimensions for SPX9000, FR10 Open Chassis

Size Voltage hp (IH) W1 W2 W3 W4 W5 H1 H2 H3 H4
FR10 480V 250 – 350 19.7 16.7 1.2 2.6 12.8 45.9 44.1 34.6 33.5
575V 200 – 300 (500) (425) (30) (67) (325) (1165) (1121) (879) (850)
Table A-12: Dimensions for SPX9000, FR10 Open Chassis (Continued)

Size Voltage hp (IH) H5 H6 H7 D1 D2 D3 D4 Lbs. (kg)
FR10 480V 250 – 350 .7 24.7 10.8 19.9 17.9 16.7 16.6 518
575V 200 – 300 (17) (627) (275) (506) (455) (423) (421) (235)
Note: SPX9000 FR12 is built of two FR10 modules.

June 2009
H2
W3 W3
W2 W2
W2 W2
Shown without
terminal cover
H1
W1
D2 D1
Figure A-14: SPX9000 Dimensions, FR11 Open Chassis
Table A-13: Dimensions for SPX9000, FR11 Open Chassis

Size Voltage hp (IH) W1 W2 W3 H1 H2 D1 D2 Lbs. (kg)
FR11 480V 400 – 550 27.9 8.6 2.6 45.5 33.5 19.8 18.4 833
575V 400 – 500 (709) (225) (67) (1155) (850) (503) (468) (378)

June 2009
W3
D6
Dia. 4
D8
D7
D6
D5
W4 W4 W4 W4 W4 Dia. 1
D1 D2 W1
H3 H1 H4
H2
Dia. 3
Dia. 2 W2 W2 W2 W2 D4 H5
D4
Dia. 3
D3
W5 W5 W5
Figure A-15: SPX9000 Dimensions, FR13 Open Chassis Inverter
Table A-14: Dimensions for SPX9000, FR13 Open Chassis Inverter

Size W1 W2 W3 W4 W5 H1 H2 H3 H4 H5
FR13 27.87 5.91 26.65 4.57 3.35 41.54 2.46 39.86 41.34 .79
(708) (150) (677) (116) (85) (1055) (62.5) (1012.5) (1050) (20)
Table A-14: Dimensions for SPX9000, FR13 Open Chassis Inverter (Continued)
Approximate Dimensions in Inches (mm)
Frame Dia. Dia. Dia. Dia. Weight
Size D1 D2 D3 D4 D5 D6 D7 D8 1 2 3 4 Lbs. (kg)
FR13 21.77 .51 .63 1.97 1.06 1.57 5.91 9.64 .35x.59 .18 .51 .37 683
(553) (13) (16) (50) (27) (40) (150) (244.8) (9x15) (4.6) (13) (9.5) (310)
Note: 9000X FR14 is built of two FR13 modules.
Note: FR13 is built from an inverter module and a converter module.

June 2009
W3 Dia. 3
D9
D8
D7
D6
Dia. 1 W4 W4 W4 D1 D2 W1
H3 H1 H4
H2
D4
W2 W2 D5 D5 H5
Dia. 2
Dia. 2
D3 W5 W5
Figure A-16: SPX9000 Dimensions, FR13 Open Chassis Converter

Table A-15: FR13 — Number of Input Units
480V hp Input Modules 690V hp Input Modules
SPX800A0-4A2N1 800 2 SPX800A0-5A2N1 800 2
SPX900A0-5A2N1 900 2
SPXH10A0-5A2N1 1000 2
Table A-16: Dimensions for SPX9000, FR13 Open Chassis Converter
Size W1 W2 W3 W4 W5 H1 H2 H3 H4 H5 D1 D2
FR13 18.74 5.91 17.52 4.57 3.35 41.54 2.46 39.86 41.34 .69 14.69 .51
(476) (150) (445) (116) (85) (1055) (62.5) (1012.5) (1050) (17.5) (373) (13)
Table A-16: Dimensions for SPX9000, FR13 Open Chassis Converter (Continued)
Size D3 D4 D5 D6 D7 D8 D9 Dia. 1 Dia. 2 Dia. 3 Lbs. (kg)
FR13 .73 6.42 2.56 1.06 1.57 5.91 5.24 .35x.59 .51 .37 295
(18.5) (163) (65) (27) (40) (150) (133) (9x15) (13) (9.5) (134)

June 2009
W3 Dia. 4
D9
D8
D7
D6
Dia. 1 W4 W4 W4 W4 W4
D1 D2 W1
H3 H1 H4
H2
D4
Dia. 2 W2 W2 W2 W2 D5 D5 H5
Dia. 3
D3 W5 W5 W5
Figure A-17: SPX9000 Dimensions, FR13 Open Chassis Converter — 900/1000 hp 480V
Table A-17: FR13 — Number of Input Units
480V hp Input Modules
SPX900A0-4A2N1 900 3
SPXH10A0-4A2N1 1000 3
Table A-18: Dimensions for SPX9000, FR13 Open Chassis Converter — 900/1000 hp 480V
Size W1 W2 W3 W4 W5 H1 H2 H3 H4 H5 D1 D2 D3
FR13 27.87 5.91 26.65 4.57 3.35 41.54 2.46 39.86 41.34 .69 14.69 .51 .73
(708) (150) (677) (116) (85) (1055) (62.5) (1012.5) (1050) (17.5) (373) (13) (18.5)
Table A-18: Dimensions for SPX9000, FR13 Open Chassis Converter — 900/1000 hp 480V (Continued)
Size D4 D5 D6 D7 D8 D9 Dia. 1 Dia. 2 Dia. 3 Dia. 4 Lbs. (kg)
FR13 6.42 2.56 1.06 1.57 5.91 5.24 .35x.59 .18 .51 .37 443
(163) (65) (27) (40) (150) (133) (9x15) (4.6) (13) (9.5) (201)

June 2009
AC Choke — CHK0650
19.57 8.11
(497) (206)
1.77
(45)
.43 x .59 (11 x 15)

Slot (9 Places)
1 1 1
19.53
1.58 17.68 (496)
15.79 (40) (449)
(401) .79
(20)
3 3 3
3.03 (77)
.79
(20) 2 2 2
7.88 .51 (13) 5.71

(200) (145) .83
(8 Places) (21)
15.75 9.61
(400) (244)
6.50 6.50
(165) (165) .24
(6)
Figure A-18: AC Choke (CHK0650) Dimensions


June 2009
8.03
(204)
19.57 1.69
(497) (43)
1 1 1
1.58 17.57
(40) 15.71 (446)
.79 (399)
(20)
3 3 3
3.03 (77)
.79
(20) 2 2 2
7.88 5.70
(200) (145) .83
.55 (21)
(14)
9.61
(244)
6.50 6.50
(165) (165) .24
(6)


June 2009
13.78 9.37
(350) (238)
1.54
(39)
1 1 1
1.18 16.58
(30) 15.08 (421)
(383)
.59
(15)
3 3 3 .75
2.64 (19)
.59 (67)
(15) 2 2 2
5.91 5.51
(150) (140)
10.32
(262)
4.72 4.72
(120) (120) .24
(6)


June 2009
8.11
(206)
1.54
(39)
1 1 1
1.18 13.51
(30) 12.17 (343)
(309)
.59
(15)
3 3 3
2.44 .49
.59 (62) (12.5)
(15)
2 2 2
5.91 4.25
(150) (108) .59
(15)
13.94 9.06
(354) (230)
4.72 4.72
(120) (120) .16
(4)


June 2009
Control Unit — SPX9000 FR10 – FR14
2.32 .63
(59) (16)
.33
(8.5) .33
(8.5)
11.82
(300) 12.94
(328.5)
2.52 5.75
(64) (146)
Figure A-22: Control Unit Dimensions


June 2009
2.32 .63
(59) (16)
.33
(8.5) .33
(8.5)
11.82 12.91
(300) (328)
2.52 5.75
(64) (146)
Figure A-23: Control Unit with Star-Coupler Board, FR12 or FR14 Only

June 2009
EMC Capability
General
For products used within the European Community (EC), the Electro Magnetic Compatibility
(EMC) directive states that the electrical equipment must not disturb the environment and
must be immune to other Electro Magnetic Disturbances in the environment.
The design intent was to develop a family of drives, which is user friendly and cost effective,
while fulfilling the user’s needs. EMC compliance was a major consideration from the outset
of the design.
The SVX9000/SPX9000 drive series is targeted at the world market. To ensure maximum
flexibility, yet meet the EMC needs of different regions, all drives meet the highest immunity
levels, while emission levels meet the requirements noted in the following section.
EMC Classification
The SVX9000/SPX9000 drive series are EMC classification H capable.
Class H
SVX9000/SPX9000 drives have been designed to fulfill the requirements of the product
standard EN 61800-3+A11 for the 1st environment restricted distribution and the 2nd
environment.
The emission levels correspond to the requirements of EN 61000-6-4.
SVX9000/SPX9000 series drives fulfill all applicable EMC immunity requirements (standards
EN 61000-6-1, EN 61000-6-2 and EN 61800-3+A11).
Declaration of Conformity
The Manufacturer’s Declarations of Conformity assuring the compliance of the SVX9000/
SPX9000 drives with the European Community (EC) EMC-directives is available upon
request.

June 2009
Warranty and Liability Information

Eaton Electrical Inc. warrants the product delivered in the Cutler-Hammer shipping package
to be free from defects in material and workmanship, under normal use and service, for
twenty four (24) months from date of manufacturing. Products that fail during this period will
be repaired or replaced at Eaton’s discretion, with the same or a functionally equivalent
product, provided the original purchaser (A) returns the failed product, and (B) provides
proof of original date of purchase. This warranty does not apply, in the judgment of Eaton, to
damage caused during shipment, handling, storage, or accidental misuse. The original
purchaser of the product must obtain a Cutler-Hammer Return Material Authorization (RMA)
number prior to returning any defective product. (When purchased through an Authorized
Distributor, the Distributor should supply an RMA number to their customer.)
The maximum liability of this warranty is limited to the purchase price of the product. In no
event, regardless of cause, shall Eaton Electrical Inc. be liable (a) for penalties or penalty
clauses of any description, or (b) for certification not otherwise specifically provided herein
and/or indemnification of purchaser or others for costs, damages or expenses, each arising
out of or related to the product or services of any order or (c) for any damages resulting from
loss of profits, use of products or for any incidental indirect or consequential damages, even
if advised of the possibility of such damages.

June 2009
Appendix B — Fault and Warning Codes

The faults with one asterisk are “Fault” only. The faults with two asterisks can be
programmed for different actions based on the chosen application. See the appropriate
application manual for specific application details.
Table B-1: Fault Codes
Fault
Code Fault Possible Cause Solution
1 Overcurrent The SVX9000/SPX9000 has detected Check loading.

a high current (>4xIn) in its output Check motor.
due to: Check cables.
• sudden heavy load increase
• short in the motor
• short in the cables to the motor
• unsuitable motor
2 Overvoltage The DC-link voltage has exceeded its Make the deceleration time longer.
high limit due to: Use a chopper and brake resistor
• too short a deceleration time (standard on some models, available
• high voltage levels or surges in as an option on others).
the utility supply Correct utility supply voltage (level is
too high).
Add input impedance to limit surges.
3** Ground (Earth) Current sensing indicates that the Check the motor and motor cables.
Fault sum of motor phase currents is not
zero.
• insulation failure in motor or
motor cables
5 Charging Switch The charging switch was open when Reset the fault and restart.
the START command was been given Should the fault re-occur, contact
due to: your Cutler-Hammer distributor.
• faulty operation
• component failure
6 Emergency stop An Emergency stop signal was Determine the reason for the
received from one of the digital Emergency stop and remedy it.
inputs
7 Saturation trip • defective component Cannot be reset from the keypad.
• motor or motor cable short Switch off power.
If this fault appears simultaneously
with Fault 1, check the motor and
motor cables.
IF THE PROBLEM IS NOT IN THE
MOTOR OR ITS CABLES, DO NOT
RE-CONNECT POWER!
Contact your Cutler-Hammer
distributor.
8 System fault • component failure Reset the fault and restart.
• faulty operation Should the fault reoccur, contact
Note: exceptional fault data record, your Cutler-Hammer distributor.
see the Active Fault Menu and Fault
Time Data Record for more
information
MN04001004E For more information visit: www.eaton.com B-1

June 2009
Table B-1: Fault Codes (Continued)

Fault
9** Undervoltage DC-link voltage is less than the If there was a supply voltage loss or
minimum safe operating voltage dip, reset the fault and restart the
limit. SVX9000/SPX9000. Check the supply
• most probable cause: too low a voltage. If it was within specification
supply voltage at the time of the fault, an internal
• SVX9000/SPX9000 internal fault failure has occurred.
Contact your Eaton distributor.
10** Input line Input line phase is low or missing. Check the utility supply voltage,
supervision cables and connections.
11** Output phase Current sensing indicates that there Check the motor cables, connections
supervision is no current in one motor phase. and motor.
12 Brake chopper • no brake resistor installed Check the brake resistor.
supervision • brake resistor is open If the resistor is ok, the chopper is
• brake chopper failure faulty. Contact your Eaton
distributor.
13 SVX9000/SPX9000 Heatsink temperature is under 14°F Provide supplemental heating or
undertemperature (-10°C) relocate the SVX9000/SPX9000 to a
warmer location.
14 SVX9000/SPX9000 Heatsink temperature is over 194°F An overtemperature warning is
overtemperature (90°C). issued when the heatsink
temperature exceeds 185°F (85°C), a
fault occurs at 194°F (90°C). Check for
the correct amount and unrestricted
flow of cooling air.
Check the heatsink for dust or dirt
buildup.
Check the highest ambient
temperature level.
Make sure that the switching
frequency is not set too high in
relation to ambient temperature and
motor load.
15** Motor stalled • motor or load mechanical failure Check motor, mechanical system and
• load is too high load level.
• stall parameter settings incorrect Confirm the stall parameter settings.
16** Motor • motor is overloaded Decrease the motor load.
overtemperature • motor overheating has been If no motor overload exists, check the
detected by the SVX9000/ temperature model parameters.
SPX9000 motor temperature
model
17** Motor underload • mechanical or load problems Check the motor. Check for a loose
• underload parameter settings belt, broken coupling or load
incorrect problems. Confirm the underload
parameter settings.
22 EEPROM Parameter save fault Upon reset of this fault, the SVX9000/
checksum fault • faulty operation SPX9000 will automatically reload
• component failure the parameter default settings. Check
all parameter settings after reset. If
the fault reoccurs, contact your Eaton
distributor.
B-2 For more information visit: www.eaton.com MN04001004E

June 2009

Fault
24* Counter fault Values displayed on the counters are

incorrect
25 Microprocessor • faulty operation Reset the fault and restart.
watchdog fault • component failure Should the fault reoccur, contact
your Eaton distributor.
26 Startup prevented Startup of the drive has been Check Start Enable/Interlock settings.
prevented
29** Thermistor fault The thermistor input of an option Check the motor cooling and the
board has detected a high motor motor loading.
temperature Check the thermistor connection.
(If the thermistor input of an option
board is not being used, it must be
short-circuited).
31 IGBT temperature IGBT Inverter Bridge Check loading.
(hardware) overtemperature protection has Check motor size.
detected a high short-term overload
current
32 Fan cooling The SVX9000/SPX9000 cooling fan Contact your Eaton distributor.
did not start when commanded
34 CAN bus Sent message not acknowledged Ensure that there is another device
communication on the bus with the appropriate
configuration.
36 Control unit The control unit cannot control the Change the control unit.
power unit and vice-versa
37* Device change • option board changed Reset.
(same type) • different power rating of drive Note: No Fault Time Data Record is
made.
38* Device added • option board added Reset.
(same type) • drive of different power rating Note: No Fault Time Data Record is
added made.
39* Device removed • option board removed Reset.
• drive removed Note: No Fault Time Data Record is
made.
40 Device unknown Unknown option board or drive Contact your Eaton distributor.
41 IGBT temperature IGBT Inverter Bridge Check loading.
overtemperature protection has Check motor size.
detected a high short-term overload
current
42** Brake resistor Brake resistor overtemperature Set the deceleration time longer.
overtemperature protection has detected excessive Use an external brake resistor.
braking
MN04001004E For more information visit: www.eaton.com B-3

June 2009

Fault
43 Encoder fault Note: exceptional fault data record, Check encoder channel connections.
see the Active Fault Menu and Fault Check the encoder board.
Time Data Record for more
information. Additional codes:
1 = Encoder 1 channel A is missing
2 = Encoder 1 channel B is missing
3 = Both encoder 1 channels are
missing
4 = Encoder reversed
44* Device change • option board changed Reset.
(different type) • different power rating of drive Note: No Fault Time Data Record is
made.
Note: Application parameter values
restored to default.
45* Device added • option board added Reset.
(different type) • drive of different power rating Note: No Fault Time Data Record is
added made.
Note: Application parameter values
restored to default.
50** Analog input Current at the analog input is Check the current loop, signal source
Iin < 4 mA < 4 mA. and wiring.
(for the signal • control cable is broken or loose
range • signal source has failed
4 to 20 mA)
51 External fault Digital input set as an external fault Check source of trigger.
input has been triggered
52 Keypad The connection between the control Check the keypad connection and
communication keypad and the SVX9000/SPX9000 keypad cable.
fault has been lost
53 Communication The data connection between the Check installation.
bus fault communication bus master and the If installation is correct contact your
communication bus board has failed Eaton distributor.
54 Slot fault Defective option board or slot Check that the board is properly
installed and seated in slot. If the
installation is correct, contact your
Eaton distributor.
56 PT100 board Temperature limit values set for the Determine the cause of the high
temperature fault PT100 board parameters have been temperature.
exceeded
B-4 For more information visit: www.eaton.com MN04001004E

June 2009
Appendix C — Troubleshooting Charts Using Fault Codes

F1 — Overcurrent
F1
Check parameters in G2.1 and G2.6
Parameter No
Settings Make corrections to the settings
OK ?
Yes Start up the drive
Yes No
Disconnect motor cable from the drive F1 ?
Start up the drive
Fault was generated by external factor. Check:

No – motor
F1 ?
– motor cable
– features of the load
Yes
Check current measuring circuit

according to instructions in service
manual and replace defective parts
Clear fault memory
Figure C-1: F1 — Overcurrent
MN04001004E For more information visit: www.eaton.com C-1

June 2009
F2 — Overvoltage
F2
Check parameters in G2.1, G2.4 and G2.6.

Notice the break chopper if used,
check parameter P6.3.3.
Parameter No
OK ?
Yes
Measure voltage in DC-bus.

Compare measured voltage to
monitored value V1.8.
Fault was generated by external factor:

– line voltage >+10%
Measure value = Yes – voltage spikes on line
Monitored value ? – feature of load
– declaration time too short for system inertia
– break resistor too small
No
Check current measuring circuit Make corrective measures to

according to instructions in service quality of line power, setting the
manual. Replace defective parts as deceleration time versus system inertia
recommended in the spare parts lists.
Clear fault memory
Note: Overvoltage triplimit is

911V in 380-500V units.
Figure C-2: F2 — Overvoltage
C-2 For more information visit: www.eaton.com MN04001004E

June 2009
F3 — Earth Fault
F3
Disconnect motor cable from the drive
Start up the drive
No
F3 ?
Yes
Check current measuring circuit Fault was generated by external factor:

according to instructions in service – damage in insulation of motor cable
manual. Replace defective parts as – damage in motor insulation
recommended in spare parts lists.
Make corrective measures
Clear fault memory
Figure C-3: F3 — Earth Fault

June 2009
F5 — Charging Switch
F5
Reset the fault and start up the unit
No
F5 ?
Yes
Test and/or replace the control board

with functional one by following
instructions in service manual.
Replace defective parts as
Set values of parameters to

comply with nature of application
Clear fault memory
Figure C-4: F5 — Charging Switch

June 2009
F6 — Emergency Stop
F6
Check the reason for external fault

programmed to a digital input. Reset the fault
and start up the unit. Measure operating
voltage (+24V DC) from frequency converter.
Measured Yes Look at the monitoring page

voltage for the digital input and measure
OK ? signal from external device.
No
Check +24V circuit in converter

If measured value If measured value
is OV=> is 24V and
replace monitored value
external device is OFF=>
replace I/O board
recommended in spare parts lists
Clear fault memory
Figure C-5: F6 — Emergency Stop

June 2009
F7 — Saturation Trip
Note: This fault also covers brake chopper.

F7 Earthfault on brakeresistor = F7.
Check the main circuit

according to instructions
in service manual
Main No Change defective parts according to

Circuit instructions in service manual
OK ?
Yes
Power up and start the drive.

Run through the frequency range Fmin-Fmax.
No
F7 ?
Yes
Check control module using instructions

in service manual and functional
test using the 9000XSERVICE tool
No
F7 ?
Yes
Clear fault memory
Figure C-6: F7 — Saturation Trip

June 2009
F8 — System Fault
F8
Reset the fault and start up the unit
No
F8 ?
Yes
Note: Subfault codes:
1 = feedback fault
Check subfault code (1-7) 2 = Asic fault
3 = Asic fault
4 = Asic fault
5 = vacon bus problem
Check control box with 9000X service 6 = charging relay fault
tool software according to 7 = charging relay fault
instructions in service manual
and change defective parts
Clear fault memory
Figure C-7: F8 — System Fault

June 2009
F9 — Undervoltage
F9
Parameter No
Settings Set values of parameters to
OK ? comply with nature of application
Yes
Measure voltage in DC-bus.

Compare actual voltage to
monitored value V1.8.
Fault was generated by either:

External factor: – line dips
Measured value = Yes – features of the load
Monitored value ? – blown input fuses
Internal factor: – faulty rectifier
No
Check the voltage measuring circuit Make corrections to parameter settings

and rectifier according to instructions
in service manual. Replace defective
parts as recommended and
listed in spare parts lists.
Clear fault memory
Figure C-8: F9 — Undervoltage

June 2009
F10 — Input Line Supervision
F10
Measure mains voltage at input terminals
Mains No
OK ? Make corrections to mains, change fuses
Yes If fuses blown, check for possible

internal failures in converter
Check rectifier-circuit and

dc-capacitors according to instructions
in service manual
Yes Occasionally existing line dips or

Measurements disturbances may activate line supervision
OK ? function. Ensure quality of line power.
No

recommended in spare part lists
Clear fault memory
Figure C-9: F10 — Input Line Supervision

June 2009
F11 — Output Phase Supervision
F11
Check connections in power transmission line

from drive to motor
Connections No Make corrective measures to circuit

OK ? from the drive to motor
Yes
Check operation of the current

measuring circuit according to
instructions in service manual

recommended and listed in spare parts lists
Clear fault memory
Figure C-10: F11 — Output Phase Supervision

June 2009
F12 — Brake Chopper Supervision
F12
Check brake resistor and connections

in brake chopper circuit Note: Earthfault on brakeresistor = F7
Circuit No Make corrective measures. Check the

OK ? dimensioning of the braking resistor.
Yes
Check conditions of brake Yes No

chopper according to instructions F12 ?
in service manual
Brake chopper No
OK ?
Yes
Replace power board Replace defective parts

according to instructions according to instructions
in service manual in service manual
Clear fault memory
Figure C-11: F12 — Brake Chopper Supervision

June 2009
F13 — Frequency Converter Under Temperature
F13
Read value of operation

temperature V1.9
Value V1.9
corresponds to Yes Unit under temperature protection operated.
Tambient, and Install unit into warmer environment
Tambient lower or install external heating element.
than -10C ?
No
Check the temperature measuring

circuit according to instructions in
service manual. Replace parts as
recommended and listed in spare
parts lists. Check control module using
instructions in service manual and
functional test using the 9000XSERVICE tool.
Clear fault memory
Figure C-12: F13 — Frequency Converter Under Temperature

June 2009
F14 — Frequency Converter Over Temperature
F14
Check operation of cooling fans;

rotation and direction of blowing
Clear blocked heat sink by blowing

compressed air along fins of the heat sink
No
F14 ?
Yes
Read value of operation

temperature V1.9
Yes Value V1.9 =

Tambient ?
No
Check the temperature measuring

circuit according to instructions in
service manual. Replace parts as
recommended and listed in spare
parts lists. Check control module using
functional test using the 9000XSERVICE tool.
Clear fault memory
Figure C-13: F14 — Frequency Converter Over Temperature

June 2009
F15 — Motor Stalled
F15
Check parameters in G2.7 and

make corrections to match
with requirements of application
No
F15 ?
Yes
Check mechanical load of the application

versus rating of the motor and the drive
Measure actual motor current and

compare it to V1.4 reading
Combination of the rating for motor and Yes Measured current =

drive do not match with mechanical load Monitored current ?
No
Check current measuring circuit

according to instructions in service manual
and replace defective parts
as recommended in spare parts lists
Clear fault memory
Figure C-14: F15 — Motor Stalled

June 2009
F16 — Motor Over Temperature
F16
Motor overheating has been detected by

frequency converter temperature model.
Measure temperature of motor.
Temperature higher Yes Motor overloaded.

than thermal capability Decrease load or provide
of the motor ? additional cooling to motor if needed.
No
Correct the parameters for

thermal protection in G2.7
No
F16 ?
Yes
Measure actual motor current

and compare it to V1.4
Measured (I) = Yes

Monitored (I) ?
No
Check current measurement

according to instructions
in service manual
Replace parts recommended
Clear fault memory
Figure C-15: F16 — Motor Over Temperature

June 2009
F17 — Motor Under Load
F17
Check settings of parameters in

G2.7 and set values according to
requirements of application
Measure motor current and compare

result to value V1.4
(I) Measured = Yes

(I) Monitored ?
No
Check the current measuring circuit

manual. Replace defective parts
as recommended in spare parts lists.
Clear fault memory
Figure C-16: F17 — Motor Under Load

June 2009
F22 — Param Fault
F22
Check parameters and

fix incorrect parameters
Disconnect input power from drive and

wait until internal power supply shuts down
Power up the drive
Test and/or replace control board

Yes with functioning one according to
F22 ?
No
No Check Parameters,
Parameters
OK ?
Yes
Clear fault memory
Figure C-17: F22 — Param Fault

June 2009
F24 — Counter Fault
F24
Reset fault and start up the unit
Clear fault memory
Figure C-18: F24 — Counter Fault
F25 — Microprocessor Watchdog Fault
F25
Reset the fault,

check the parameters and start up the unit
Test and/or replace the control board

with functioning one according to
Clear fault memory
Figure C-19: F25 — Microprocessor Watchdog Fault

June 2009
F31 — IGBT Temperature (Hardware)
Note: F31 occurs only from FR9 and bigger

frame sizes.
F31
If F31 and F41 occur at the same time,
use F41 troubleshooting.
Parameter No
OK ?
Start up the drive

Yes
Yes No
Start up the drive
No
F31 ? Check motor and cables
Yes
Motor No
and cables
OK ?
Yes Fix motor and

cables
Check current measuring Disbalance fault.

circuit according to instructions Check power modules and
in service manual current measuring circuit.
and replace defective parts Replace defective parts.
Clear fault memory
Figure C-20: F31 — IGBT Temperature (Hardware)

June 2009
F32 — Fan Cooling
Note: This fault is for FR8.

F32
Check fan inverter
Fan No
Inverter Replace fan inverter
OK ?
Yes Check the fan
No
Fan OK ? Replace fan
Yes
Check control module using

functional test using the 9000XSERVICE tool
Clear fault memory
Figure C-21: F32 — Fan Cooling

June 2009
F36 — Control Unit
F36
Reset the fault
No
F36 ?
Yes

Clear fault memory
Figure C-22: F36 — Control Unit
F37 — Device Change
Note: F37 should appear when same

F37 type of power unit and/or option
board have been changed.
Reset the fault
Clear fault memory
Note: Faulty board is displayed

on panel bottom line
1 = Control card A = Slot A
2 = Control unit B = Slot B
3 = Power card C = Slot C
4 = Power unit D = Slot D
5 = Adapter card E = Slot E
Figure C-23: F37 — Device Change (Indication Only)

June 2009
F38 — Device Added
Note: F38 should appear when same type

F38 of option board has been added.
Reset the fault
Clear fault memory

5 = Adapter card C = Slot C
D = Slot D
E = Slot E
Figure C-24: F38 — Device Added (Indication Only)
F39 — Device Removed
Note: F39 should appear when an option

F39 board has been removed.
Reset the fault
Clear fault memory

A = Slot A
B = Slot B
C = Slot C
D = Slot D
E = Slot E
5 = Adapter card
Figure C-25: F39 — Device Removed (Indication Only)

June 2009
F40 — Device Unknown
Note: F40 should appear if installed

F40 power board, control board
and/or option board are faulty.
Disconnect input power from drive and

wait until internal power supply shuts down
Power up the unit
No
F40 ?
Yes
Faulty board is displayed on panel bottom line
Change the faulty board and reset the fault
Clear fault memory

3 = Power card C = Slot C
4 = Power unit D = Slot D
5 = Adapter card E = Slot E
Figure C-26: F40 — Device Unknown

June 2009
F41 — IGBT Temperature
Note: If F41 occurs continuously,

F41 upgrade software version.
Parameter No
OK ?
Yes Start up the drive
Yes No
Start up the drive
Fault was generated by external factor. Check:

No – motor
F41 ?
– motor cable
– features of the load
Yes
Check current measurement circuit

manual and replace defective parts
Clear fault memory
Figure C-27: F41 — IGBT Temperature

June 2009
F42 — Brake Resistor Over Temperature
F42
Too rough usage of the internal brakeresistor
Is it possible Yes
to slow down the Use longer deceleration time and try again
process ?
No
Change parameters – external brakeresistor. Yes

F42 ?
Mount properly sized external brakeresistor.
No
Clear fault memory
Figure C-28: F42 — Brake Resistor Over Temperature

June 2009
F44 — DevParChange
Note: F44 should appear when different

F44 type power unit and/or option
board have been changed.
Yes Copy parameters to keypad

Use old or upload parameters from drive to PC
parameters ? and save them to file
No Reset the fault
Reset the fault Download parameters to drive
Check parameters
Disconnect input power form drive and wait

until internal power supply shuts down
Power up the drive
Check parameters
Clear fault memory

A = Slot A
B = Slot B
C = Slot C
D = Slot D
E = Slot E
4 = Power unit
Figure C-29: F44 — DevParChange

June 2009
F45 — DevParAdded
Note: F45 should appear when different type

F45 option board has been added.
Reset the fault
Clear fault memory

A = Slot A
B = Slot B
C = Slot C
D = Slot D
E = Slot E
Figure C-30: F45 — DevParAdded

June 2009
F50 — Analog Input Iin < 4 mA
F50
Check value on monitoring

page corresponding to the input
Measure mA signal of
the measurement device
Measured value = No
Monitored value ?
Yes
No Test input on the option board, if faulty

I<4mA ?
replace option board with functioning one

Yes with functioning one according to
Make corrections to external circuit recommended in spare parts lists.
Clear fault memory
Figure C-31: F50 — Analog Input Iin < 4 mA

June 2009
F51 — External Fault
F51
Set parameters to match with application
Read status of programming input from

corresponding monitoring page
Actual status = Yes

External reason for activating the fault
Monitored status ?
No
Check I/O option board, replace if necessary Make corrections to the external devices

Clear fault memory
Figure C-32: F51 — External Fault

June 2009
F52 — Keypad Communication Fault
F52
Check keypad connections and its cable.

Replace broken parts.
Plug in a functional panel
No
F26 ?
Yes

Clear fault memory
Figure C-33: F52 — Keypad Communication Fault

June 2009
Appendix D — Spare Parts

Series Option Board Kits
The 9000X Series drives can accommodate a wide selection of expander and adapter option
boards to customize the drive for your application needs. The drive’s control unit is designed
to accept a total of five option boards (see Figure D-1).
The 9000X Series factory installed standard board configuration includes an A9 I/O board and
an A2 relay output board, which are installed in slots A and B.
DE
A B C
Figure D-1: 9000X Series Option Boards
Table D-1: Option Board Kits

Allowed Field Factory
Slot Installed Installed 9000X Ready Programs
Option Kit Locations Catalog Option Local/
Description
Number Designator Basic Remote Standard MSS PID Multi-P. PFC
Standard I/O Cards (See Figure D-1)
2 RO (NC/NO) B OPTA2 — X X X X X X X
6 DI, 1 DO, 2 AI, 1AO, 1 A OPTA9 — X X X X X X X
+10V DC ref, 2 ext +24V DC/
EXT +24V DC
Extended I/O Card Options
2 RO, Therm B OPTA3 A3 — X X X X X X
Encoder low volt +5V/15V24V C OPTA4 A4 — X X X X X X
Encoder high volt +15V/24V C OPTA5 A5 — X X X X X X
Double encoder — SPX Only C OPTA7 A7 X X X X X X X
6 DI, 1 DO, 2 AI, 1 AO A OPTA8 A8 — X X X X X X
3 DI (Encoder 10 – 24V), C OPTAE AE X X X X X X X
Out +15V/+24V, 2 DO
(pulse+direction) — SPX Only
Option card must be installed in one of the slots listed for that card. Slot indicated in Bold is the preferred location.
AI = Analog Input; AO = Analog Output, DI = Digital Input, DO = Digital Output, RO = Relay Output
MN04001004E For more information visit: www.eaton.com D-1

June 2009
Table D-1: Option Board Kits (Continued)

Allowed Field Factory
Slot Installed Installed 9000X Ready Programs
Option Kit Locations Catalog Option Local/
Description
Number Designator Basic Remote Standard MSS PID Multi-P. PFC
Extended I/O Card Options (Continued)
6 DI, 1 ext +24V DC/EXT B, C, D, E OPTB1 B1 — — — — — X X
+24V DC
1 RO (NC/NO), 1 RO (NO), B, C, D, E OPTB2 B2 — — — — — X X
1 Therm
1 AI (mA isolated), 2 AO B, C, D, E OPTB4 B4 — X X X X X X
(mA isolated), 1 ext +24V DC/
EXT +24V DC
3 RO (NO) B, C, D, E OPTB5 B5 — — — — — X X
1 ext +24V DC/EXT +24V DC, B, C, D, E OPTB8 B8 — — — — — — —
3 Pt100
1 RO (NO), 5 DI 42 – 240V AC B,C, D, E OPTB9 B9 — — — — — X X
Input
SPI, Absolute Encoder C OPTBB BB — — — — — — —
Communication Cards
Modbus D, E OPTC2 C2 X X X X X X X
Johnson Controls N2 D, E OPTC2 CA — — — — — — —
Modbus TCP D, E OPTCI CI X X X X X X X
BACnet D, E OPTCJ CJ X X X X X X X
Ethernet IP D, E OPTCK CK X X X X X X X
Profibus DP D, E OPTC3 C3 X X X X X X X
LonWorks D, E OPTC4 C4 X X X X X X X
Profibus DP (D9 Connector) D, E OPTC5 C5 X X X X X X X
CanOpen (Slave) D, E OPTC6 C6 X X X X X X X
DeviceNet D, E OPTC7 C7 X X X X X X X
Modbus (D9 Type Connector) D, E OPTC8 C8 X X X X X X X
Adapter — SPX Only D, E OPTD1 D1 X X X X X X X
Adapter — SPX Only D, E OPTD2 D2 X X X X X X X
RS-232 with D9 Connection D, E OPTD3 D3 X X X X X X X
Keypad
9000X Series Local/Remote — KEYPAD- — — — — — — — —
Keypad (Replacement Keypad) LOC/REM
9000X Series Remote Mount — OPTRMT — — — — — — — —
Keypad Unit (Keypad not -KIT-
included, includes 10 ft. cable, 9000X
keypad holder, mounting
hardware)
9000X Series RS-232 Cable, — PP00104 — — — — — — — —
13 ft.
Option card must be installed in one of the slots listed for that card. Slot indicated in Bold is the preferred location.
AI = Analog Input; AO = Analog Output, DI = Digital Input, DO = Digital Output, RO = Relay Output
OPTC2 is a multi-protocol option card.
D-2 For more information visit: www.eaton.com MN04001004E

June 2009
Johnson Controls Metasys™ N2 Network Communications

The OPTC2 fieldbus board provides communication between the 9000X Drive and a Johnson
Controls Metasys™ N2 network. With this connection, the drive can be controlled, monitored
and programmed from the Metasys system. The N2 fieldbus is available as a factory installed
option and as a field installable kit.
Modbus/TCP Network Communications

The Modbus/TCP Network Card OPTCI is used for connecting the 9000X Drive to Ethernet
networks utilizing Modbus protocol. It includes an RJ-45 pluggable connector. This interface
provides a selection of standard and custom register values to communicate drive
parameters. The board supports 10 Mbps and 100 Mbps communication speeds. The IP
address of the board is configurable over Ethernet using a supplied software tool.
BACnet Network Communications
The BACnet Network Card OPTCJ is used for connecting the 9000X Drive to BACnet
networks. It includes a 5.08 mm pluggable connector. Data transfer is Master-Slave/Token
Passing (MS/TP) RS-485. This interface uses a collection of 30 Binary Value Objects (BVOs)
and 35 Analog Value Objects (AVOs) to communicate drive parameters. The card supports
9.6, 19.2 and 38.4 Kbaud communication speeds and supports network addresses 1 – 127.
Ethernet/IP Network Communications

The Ethernet/IP Network Card OPTCK is used for connecting the 9000X Drive to Ethernet/
Industrial Protocol networks. It includes an RJ-45 pluggable connector. The interface uses CIP
objects to communicate drive parameters (CIP is “Common Industrial Protocol”, the same
protocol used by DeviceNet). The board supports 10 Mbps and 100 Mbps communication
speeds. The IP address of the board is configurable by Static, BOOTP and DHCP methods.
Modbus RTU Network Communications

The Modbus Network Card OPTC2 is used for connecting the 9000X Drive as a slave on a
Modbus network. The interface is connected by a 9-pin DSUB connector (female) and the
baud rate ranges from 300 to 19200 baud. Other communication parameters include an
address range from 1 to 247; a parity of None, Odd or Even; and the stop bit is 1.
Profibus Network Communications

The Profibus Network Card OPTC3 is used for connecting the 9000X Drive as a slave on a
Profibus-DP network. The interface is connected by a 9-pin DSUB connector (female). The
baud rates range from 9.6K baud to 12M baud, and the addresses range from 1 to 127.
LonWorks Network Communications

The LonWorks Network Card OPTC4 is used for connecting the 9000X Drive on a LonWorks
network. This interface uses Standard Network Variable Types (SNVT) as data types. The
channel connection is achieved using a FTT-10A Free Topology transceiver via a single
twisted transfer cable. The communication speed with LonWorks is 78 kBits/s.
CanOpen (Slave) Communications

The CanOpen (Slave) Network Card OPTC6 is used for connecting the 9000X Drive to a host
system. According to ISO11898 standard cables to be chosen for CAN bus should have a
nominal impedance of 120Ω, and specific line delay of nominal 5 nS/m. 120Ω line termination
resistors required for installation.

June 2009
DeviceNet Network Communications

The DeviceNet Network Card OPTC7 is used for connecting the 9000X Drive on a DeviceNet
Network. It includes a 5.08 mm pluggable connector. Transfer method is via CAN using a
2-wire twisted shielded cable with 2-wire bus power cable and drain. The baud rates used for
communication include 125K baud, 250K baud and 500K baud.
Drive Options
Control Panel Options
Table D-2: Control Panel Factory Options
Field Installed
Factory
Installed NEMA Type 1
Option Catalog
Description Code Number
Local/Remote Keypad SVX9000 Control Panel — This option is A KEYPAD-LOC/REM

standard on all drives and consists of an RS-232 connection, backlit
alphanumeric LCD display with nine indicators for the RUN status and
two indicators for the control source. The nine pushbuttons on the
panel are used for panel programming and monitoring of all 9000X
parameters. The panel is detachable and isolated from the input line
potential. Include LOC/REM key to choose control location.
Keypad Remote Mounting Kit — This option is used to remote mount — OPTRMT-KIT-9000X
the 9000X keypad. The footprint is compatible to the SV9000 remote
mount kit. Includes 10 ft. cable, keypad holder and mounting hardware.
Keypad Blank — 9000X Series select keypad for use with special and — KEYPAD-BLANK
custom applications.
9000XDrive — A PC-based tool for controlling and monitoring of the — 9000XDRIVE
9000X. Features include: loading parameters that can be saved to a file
or printed, setting references, starting and stopping the motor,
monitoring signals in graphical or text form, and real-time display. To
avoid damage to the drive or computer, SVDrivecable must be used.
SVDrivecable — 6 ft. (1.8m) RS-232 cable (22 gauge) with a 7-pin — SVDRIVECABLE
connector on each end. Should be used in conjunction with the 9000X
Drive option to avoid damage to the drive or computer. The same cable
can be used for downloading specialized applications to the drive.

June 2009
Spare Units & Replacement Parts for 9000X Drives

Table D-3: 9000X Spare Units
Catalog
Description Number
Control Unit – Includes the control board, blue base housing, installed 9000X software CSBS0000000000 (for SVX)
program and blue flip cover. Does not include any OPT boards or keypad. See Figure D-1 CPBS0000000000 (for SPX)
and Table D-1 (Page D-1) for standard and option boards and keypad.
208 – 240V
Table D-4: Replacement Parts — 9000X Drives, 208 – 240V
Frame: 4 5 6 7 8
Catalog
hp (IH): 3/4 1 1-1/2 2 3 5 5 7-1/2 10 15 20 25 30 40 50 60 Number
Control Board
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00252 (for SVX)
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00561 (for SPX)
Power Boards
1 VB00308-0004-2
1 VB00308-0007-2
1 VB00308-0008-2
1 VB00310-0011-2
1 VB00310-0012-2
1 VB00313-0017-2
1 VB00313-0025-2
1 VB00313-0031-2
1 VB00316-0048-2
1 VB00316-0061-2
1 VB00319-0075-2
1 VB00319-0088-2
1 VB00319-0114-2
1 VB00322-0140-2
1 VB00322-0170-2
1 VB00322-0205-2
Electrolytic Capacitors
2 2 2 PP01000
2 2 PP01001
2 2 PP01002
2 PP01003
2 2 PP01004
2 2 2 4 4 PP01005
4 PP01099
5 hp IL only; has no corresponding IH rated hp rating.

June 2009
Table D-4: Replacement Parts — 9000X Drives, 208 – 240V (Continued)

Frame: 4 5 6 7 8
Catalog
hp (IH): 3/4 1 1-1/2 2 3 5 5 7-1/2 10 15 20 25 30 40 50 60 Number
Cooling Fans
1 1 1 1 1 PP01060
1 1 1 PP01061
1 1 PP01062
1 1 1 PP01063
1 1 1 PP01123
1 1 1 1 1 PP01086
1 1 1 1 1 PP01088
1 1 1 PP01049
1 2 2 CP01180
1 1 1 PP08037
IGBT Modules
1 1 CP01304
1 CP01305
1 1 1 CP01306
1 CP01307
1 CP01308
1 PP01022
1 PP01023
1 PP01024
1 PP01025
1 PP01029
1 PP01026
1 1 PP01027
Choppers/Rectifiers
1 CP01367
1 CP01368
Diode/Thyristor Modules
3 3 3 PP01035
3 3 3 CP01268
Rectifying Boards
1 1 1 VB00242
1 1 1 VB00227
5 hp IL only; has no corresponding IH rated hp rating.
PP00061 capacitor not included in main fan; please order separately.

June 2009
FR4 – FR9, 380 – 500V

Table D-5: Replacement Parts — FR4 – FR9 9000X Drives, 380 – 500V
Frame: 4 5 6 7 8 9
Catalog
hp (IH): 1 1-1/2 2 3 5 7-1/2 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 Number
Control Board
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00252 (for SVX)
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00561 (for SPX)
Power Boards
1 VB00208-0003-5
1 VB00208-0004-5
1 VB00208-0005-5
1 VB00208-0007-5
1 VB00208-0009-5
1 VB00210-0012-5
1 VB00213-0016-5
1 VB00213-0022-5
1 VB00213-0031-5
1 VB00216-0038-5
1 VB00216-0045-5
1 VB00216-0061-5
1 VB00219-0072-5
1 VB00219-0087-5
1 VB00219-0105-5
1 VB00236-0140-5
1 VB00236-0168-5
1 VB00236-0205-5
2 2 2 2 PP01000
2 2 PP01001
2 2 PP01002
2 PP01003
2 2 2 PP01004
2 2 2 4 4 4 8 8 PP01005
Cooling Fans
1 1 1 1 1 1 PP01060
1 1 1 PP01061
1 1 1 PP01062
1 1 1 PP01063
1 1 1 PP01123
1 1 PP01080
IL only; has no corresponding IH rated hp rating.

June 2009
Table D-5: Replacement Parts — FR4 – FR9 9000X Drives, 380 – 500V (Continued)
Frame: 4 5 6 7 8 9
Catalog
hp (IH): 1 1-1/2 2 3 5 7-1/2 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 Number
Cooling Fans (Continued)
1 1 1 1 1 1 PP01086
1 1 1 PP01088
1 1 1 1 1 1 PP01049
1 1 1 CP01180
1 2 PP01068
1 1 PP09051
IGBT Modules
1 1 1 CP01304
1 1 CP01305
1 1 CP01306
1 CP01307
1 CP01308
1 1 PP01022
1 PP01023
1 PP01024
1 PP01025
1 PP01029
1 PP01026
1 1 PP01027
Chopper/Rectifiers
1 1 CP01367
1 CP01368
3 3 3 PP01035
3 3 3 CP01268
3 3 PP01037
Rectifying Boards
1 1 1 VB00242
1 1 1 VB00227
1 1 VB00459
Rectifying Module Sub-assembly
1 1 FR09810
Power Module Sub-assemblies
1 FR09-150-4-ANS
1 FR09-200-4-ANS
For FR9 NEMA Type 12 you need two PP01068 internal fans.
See Table D-9 for details.

June 2009
FR10 – FR12, 380 – 500

Frame: 10 11 12
Catalog
hp (IH): 250 300 350 400 500 550 600 650 700 Number
Control Board
1 1 1 1 1 1 1 1 1 VB00561
Shunt Boards
6 VB00537
6 VB00497
6 12 12 12 VB00498
9 VB00538
9 VB00513
9 VB00514
Driver Boards
3 3 3 VB00489
1 1 1 2 2 2 VB00487
Driver Adapter Board
1 1 1 2 2 2 VB00330
ASIC Board
1 1 1 1 1 1 2 2 2 VB00451
Feedback Interface Board
2 2 2 VB00448
Star Coupler Board
1 1 1 VB00336
Power Modules
1 1 1 2 2 2 2 2 2 FR10820
2 2 2 FR10828
1 FR10-250-4-ANS
1 FR10-300-4-ANS
1 2 2 2 FR10-350-4-ANS
3 FR11-400-4-ANS
3 FR11-500-4-ANS
3 FR11-550-4-ANS
Rectifying board not included.

June 2009
Frame: 10 11 12
Catalog
hp (IH): 250 300 350 400 500 550 600 650 700 Number
2 2 2 3 3 3 4 4 4 PP00060
12 12 12 18 18 18 24 24 24 PP01005
Fuses
1 1 1 1 1 1 2 2 2 PP01094
2 2 2 2 2 2 4 4 4 PP01095
Cooling Fans and Isolation Transformers
2 2 2 3 3 3 4 4 4 VB00299
2 2 2 3 3 3 4 4 4 PP01080
2 2 2 4 4 4 PP01068
1 1 1 1 1 1 2 2 2 PP01096
1 1 1 2 2 2 FR10844
1 1 1 3 3 3 2 2 2 FR10845
1 1 1 2 2 2 FR10846
1 1 1 3 3 3 2 2 2 FR10847
Rectifying Board
1 1 1 2 2 2 2 2 2 VB00459

June 2009
FR6 – FR9, 525 – 690V

Frame: 6 7 8 9
Catalog
hp (IH): 2 3 5 5 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 Number
Control Board
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00252 (for SVX)
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VB00561 (for SPX)
Driver Board
1 VB00404-0004-6
1 VB00404-0005-6
1 VB00404-0007-6
1 VB00404-0010-6
1 VB00404-0013-6
1 VB00404-0018-6
1 VB00404-0022-6
1 VB00404-0027-6
1 VB00404-0034-6
Power Boards
1 1 1 1 1 1 1 1 1 VB00414
1 VB00419-0041-6
1 VB00419-0052-6
1 VB00422-0062-6
1 VB00422-0080-6
1 VB00422-0100-6
Power Modules
1 FR09-100-5-ANS
1 FR09-125-5-ANS
1 FR09-150-5-ANS
1 FR09-175-5-ANS
2 2 2 2 2 2 2 2 2 PP01093
2 2 4 4 8 8 8 8 PP01041
4 PP01040
Fuses
1 1 1 1 1 1 1 PP01094
2 2 2 2 2 2 2 PP01095

June 2009
Frame: 6 7 8 9
Catalog
hp (IH): 2 3 5 5 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 Number
Cooling Fans
1 1 1 1 1 PP01061
1 1 1 1 PP01062
1 1 PP01063
1 1 1 PP01123
1 1 1 1 1 1 1 1 1 1 1 PP01049
1 1 1 CP01180
1 1 1 1 PP01068
1 1 1 1 PP01080
Fan Power Supply
1 1 1 VB00299
IGBT Modules
3 3 3 3 3 3 3 3 3 PP01091
1 1 PP01089
1 1 1 PP01127
IGBT/Diode (Brake)
1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 PP01040
Diode Module
1 1 1 1 1 1 1 1 1 PP01092
3 3 PP01071
3 3 3 3 PP01072
Rectifying Boards
1 1 VB00442
1 1 1 1 VB00460
Rectifying Module Sub-assemblies
1 1 1 FR09810
1 1 1 FR09811
For NEMA Type 12, two PP01068 internal fans are needed.

June 2009
FR10 – FR12, 525 – 690V

Frame: 10 11 12
Catalog
hp (IH): 200 250 300 400 450 500 550 600 700 Number
Control Board
1 1 1 1 1 1 1 1 1 VB00561
Shunt Boards
6 VB00545
6 VB00510
6 12 12 12 VB00511
9 VB00546
9 VB00547
9 VB00512
Driver Boards
1 1 1 2 2 2 VB00487
3 3 3 VB00489
Driver Adapter Board
1 1 1 2 2 2 VB00330
ASIC Board
1 1 1 1 1 1 2 2 2 VB00451
Feedback Interface Board
2 2 2 VB00448
Star Coupler Board
1 1 1 VB00336
Power Modules
1 1 1 2 2 2 2 2 2 FR10821
2 2 2 FR10829
1 FR10-200-5-ANS
1 FR10-250-5-ANS
1 2 2 2 FR10-300-5-ANS
3 FR11-400-5-ANS
3 FR11-450-5-ANS
3 FR11-500-5-ANS
2 2 2 3 3 3 4 4 4 PP00060
12 12 12 18 18 18 24 24 24 PP01099
Rectifying board not included.

June 2009
Frame: 10 11 12
Catalog
hp (IH): 200 250 300 400 450 500 550 600 700 Number
Fuses
1 1 1 1 1 1 2 2 2 PP01094
2 2 2 2 2 2 4 4 4 PP01095
Cooling Fans and Isolation Transformers
2 2 2 3 3 3 4 4 4 VB00299
2 2 2 3 3 3 4 4 4 PP01080
2 2 2 4 4 4 PP01068
1 1 1 1 1 1 2 2 2 PP01096
1 1 1 2 2 2 FR10844
1 1 1 3 3 3 2 2 2 FR10845
1 1 1 2 2 2 FR10846
1 1 1 3 3 3 2 2 2 FR10847
Fan Power Supply
1 1 1 VB00299
Rectifying Boards
1 1 1 2 2 2 2 2 2 VB00460
Power Module
Table D-9: Power Module Catalog Number Matrix
FR10 – 000 – 4 – A N S
Frame Code Varnishing
S = Standard V = Varnished
Horsepower
Example: 150 = 150 hp Brake Option
(See Table 1-1 on Page 1-2.)
N = No Brake Chopper
B = Brake Chopper
Voltage
Cooling Type
4 = 380 – 500V
A = Air
5 = 525 – 690V

Eaton’s electrical business PowerChain Management
is a global leader in power solutions help enterprises
distribution, power quality, achieve sustainable and
control, and industrial competitive advantages
automation products and through proactive
services. Eaton’s global management of the power
electrical product lines, system as a strategic,
including Cutler-Hammer,T integrated asset throughout
Moeller,T Powerware,T its life cycle. With Eaton’s
Holec,T MEM,T Santak,T distribution, control, and
and MGE Office Protection power quality equipment;
Systems,E provide full-scale engineering
customer-driven PowerChain services; and information
ManagementT solutions management systems, the
to serve the power system power system is positioned
needs of the data center, to deliver powerful results:
industrial, institutional, greater reliability, operating
government, utility, cost efficiencies, effective
commercial, residential, use of capital, enhanced
and OEM markets worldwide. safety, and risk mitigation.
Eaton Corporation
Electrical Sector
1111 Superior Ave.
Cleveland, OH 44114
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2009 Eaton Corporation PowerChain Management is a registered

All Rights Reserved trademark of Eaton Corporation.
Printed in USA
Publication No. MN04001004E / Z8862 All other trademarks are property of their
June 2009 respective owners.

VDF - Svx030a1-4a1b2 - Um

Uploaded by

Copyright:

Available Formats

VDF - Svx030a1-4a1b2 - Um

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VDF - Svx030a1-4a1b2 - Um

Uploaded by

Copyright:

Available Formats

Effective June 2009

9000X AF Drives Supersedes October 2007

Important Notice – Please Read

NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A

The information contained in this manual is subject to change without notice.

Cover Photo: Cutler-Hammer® SVX9000/SPX9000 AF Drives.

MN04001004E For more information visit: www.eaton.com i

ii For more information visit: www.eaton.com MN04001004E

MN04001004E For more information visit: www.eaton.com iii

List of Figures (Continued)

iv For more information visit: www.eaton.com MN04001004E

List of Figures (Continued)

MN04001004E For more information visit: www.eaton.com v

List of Tables (Continued)

vi For more information visit: www.eaton.com MN04001004E

This symbol is the “Safety Alert Symbol.” It occurs with either of

Hazardous High Voltage

MN04001004E For more information visit: www.eaton.com vii

Warnings and Cautions

viii For more information visit: www.eaton.com MN04001004E

MN04001004E For more information visit: www.eaton.com ix

x For more information visit: www.eaton.com MN04001004E

How to Use This Manual

Receiving and Inspection

MN04001004E For more information visit: www.eaton.com 1-1

Open SVX9000/SPX9000 Catalog Numbers

1-2 For more information visit: www.eaton.com MN04001004E

4 230V, 1 – 3 hp IL, 3/4 – 3 hp IH 0.8 — 0.8 3.9 (100) 2.0

Figure 2-1: Mounting Space Requirements.

MN04001004E For more information visit: www.eaton.com 2-1

230V, 3/4 – 3 hp IH 41 cfm (70 m3/h)

Standard Mounting Instructions

2-2 For more information visit: www.eaton.com MN04001004E

Chapter 3 — Power Wiring

1 (0.3) ≤ 164 (50)

MN04001004E For more information visit: www.eaton.com 3-1

UL Compatible Cable Selection and Installation

1 FR4 4.2 4.8 3 10 14 14 16 – 12 16 – 14

3-2 For more information visit: www.eaton.com MN04001004E

Table 3-3: 40°C Cable and Fuse Sizes — 480V Ratings

1-1/2 FR4 3 3.3 3 10 14 14 16 – 12 16 – 14

MN04001004E For more information visit: www.eaton.com 3-3

Table 3-4: 40°C Cable and Fuse Sizes — 575V Ratings

3 FR6 3.9 4.5 3 10 14 14 14 – 0 14 – 2

250 FR10 300 2 x 2/0 1.18 x 0.25 3

3-4 For more information visit: www.eaton.com MN04001004E

200 FR10 208 2x2/0 1.18 x .25 3

Table 3-9: Maximum Symmetrical Supply Current

3/4 – 30 hp 230 100,000A

MN04001004E For more information visit: www.eaton.com 3-5

UL Compatible Cable Selection and Installation with Breaker

Table 3-11: Cable and Breaker Sizes – 480V Ratings

1-1/2 FR4 3.3 15 14 14 12 – 16 14 – 16

3-6 For more information visit: www.eaton.com MN04001004E

Table 3-12: Cable and Breaker Sizes – 575V Ratings

2 FR6 3.3 15 14 14 1/0 – 14 2 – 14

MN04001004E For more information visit: www.eaton.com 3-7

Table 3-13: Power Connection Tightening Torque

230V, 3/4 – 3 hp FR4 5 0.6