Scribd Logo
Upload

Welcome to Scribd!

  • 106 views

    ASTM B 906 Tolerances

    Uploaded by

    Jamil Salman

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    ASTM B 906 Tolerances

    Uploaded by

    Jamil Salman
    106 views1 page

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    106 views1 page

    ASTM B 906 Tolerances

    Uploaded by

    Jamil Salman

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    B 906 – 02 (2006)

    TABLE A1.4 Permissible Variations in Length for Hot-Rolled and


    Cold-Rolled Sheets Not Resquared
    Length, ft [mm] Tolerances, in. [mm]
    Up to 10 [3048], incl ⁄ [6.35] over, 0
    14

    Over 10 [3048] to 20 [6096], incl 1⁄2 [12.70] over, 0 under

    TABLE A1.5 Permissible Variations in Camber for Hot-Rolled and


    Cold-Rolled Sheets Not Resquared and Cold-Rolled CoilsA
    Tolerance per Unit Length of Any 8 ft
    Specified Width, in. [mm]
    [2438 mm], in. [mm]
    24 [610] to 36 [914], incl 1⁄8 [3.18]

    Over 36 [914] 3⁄32 [2.38]

    A
    Camber is the greatest deviation of a side edge from a straight line and
    measurement is taken by placing an 8-ft [2438-mm] straightedge on the concave
    side and measuring the greatest distance between the sheet edge and the
    straightedge.

    TABLE A1.6 Permissible Variations in Flatness for Hot-Rolled


    and Cold-Rolled Sheets Specified to Stretcher-Leveled Standard
    of Flatness (Not Including Hard Tempers of 2XX and 3XX Series)
    Specified Flatness
    Thickness, Width, in. [mm] Length, in. [mm] Tolerance,A
    in. [mm] in. [mm]
    Under ⁄
    3 16 [4.76] to 48 [1219], incl to 96 [2438], incl 18⁄ [3.18]
    Under ⁄
    3 16 [4.76] to 48 [1219], incl over 96 [2438] 14⁄ [6.35]
    Under 3⁄16 [4.76] over 48 [1219] to 96 [2438], incl 1 ⁄4 [6.35]
    Under 3⁄16 [4.76] over 48 [1219] over 96 [2438] 1 ⁄4 [6.35]
    A
    Maximum deviation from a horizontal flat surface.

    TABLE A1.7 Permissible Variations in Diameter for Hot-Rolled


    and Cold-Rolled Sheets, Sheared Circles
    Tolerance Over Specified Diameter (No
    Tolerance Under), in. [mm]
    Specified Thickness, in. [mm] Diameters Diameters 30 Diameters
    Under 30 in. [762] to 48 in. Over 48 in.
    [762] [1219] [1219]
    0.0972 [2.46] and thicker 1⁄8 [3.18] 3⁄16 [4.76] 1⁄4 [6.35]

    0.0971 [2.46] to 0.0568 [1.45], incl 3⁄32 [2.38] 5⁄32 [3.97] 7⁄32 [5.56]

    0.0567 [1.45] and thinner 1⁄16 [1.59] 1⁄8 [3.18] 3⁄16 [4.76]

    TABLE A1.12 Permissible Variations in Thickness for PlatesA,B


    Width, in. [mm]
    Over 84 [2134] to 120 Over 120 [3048] to
    Specified Thickness, in. [mm] To 84 [2134], incl Over 144 [3658]
    [3048], incl 144 [3658], incl
    C
    Tolerance Over Specified Thickness, in. [mm]
    ⁄ [4.76] to 3⁄8 [9.52], excl
    3 16 0.045 [1.14] 0.050 [1.27] ... ...
    3⁄8 [9.52] to 3⁄4 [19.05], excl 0.055 [1.40] 0.060 [1.52] 0.075 [1.90] 0.090 [2.29]
    3⁄4 [19.05] to 1 [25.40], excl 0.060 [1.52] 0.065 [1.65] 0.085 [2.16] 0.100 [2.54]
    1 [25.40] to 2 [50.80], excl 0.070 [1.78] 0.075 [1.90] 0.095 [2.41] 0.115 [2.92]
    2 [50.80] to 3 [76.20], excl 0.125 [3.18] 0.150 [3.81] 0.175 [4.44] 0.200 [5.08]
    3 [76.20] to 4 [101.6], excl 0.175 [4.44] 0.210 [5.33] 0.245 [6.22] 0.280 [7.11]
    4 [101.6] to 6 [152.4], excl 0.250 [6.35] 0.300 [7.62] 0.350 [8.89] 0.400 [10.16]
    6 [152.4] to 8 [203.2], excl 0.350 [8.89] 0.420 [10.67] 0.490 [12.45] 0.560 [14.22]
    8 [203.2] to 10 [254.0], excl 0.450 [11.43] 0.540 [13.72] 0.630 [16.00] ...
    A
    Thickness is measured along the longitudinal edges of the plate at least 3⁄8 in. [9.52 mm], but not more than 3 in. [76.20 mm], from the edge.
    B
    For plates up to 10 in. [254.0 mm], excl, in thickness, the tolerance under the specified thickness is 0.010 in. [0.25 mm].
    C
    For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown. For plates of irregular shape, the
    over thickness tolerances apply to the greatest width corresponding to the width ranges shown.

    9
    Copyright by ASTM Int'l (all rights reserved); Mon Jul 16 08:49:21 EDT 2007
    Downloaded/printed by
    Elena Giovanetti (Infodoc SRL) pursuant to License Agreement. No further reproductions authorized.

    You might also like