2/2 Solenoid Directional Valve

Poppet Type, Pilot Operated

Normally Open
UNF Cartridge – 350 bar
up to   75 l/min
WS10Y-01
up to 350 bar

FUNCTION FEATURES
zz Coil seals protect the solenoid system
zz Wide variety of connectors available
zz Excellent switching performance by high power HYDAC solenoid
zz Exposed surfaces zinc-nickel plated for increased corrosion protection
(1.000 h Salt spray test)

SPECIFICATIONS*
Operating pressure: max. 350 bar
Nominal flow: max.   75 l/min
Leakage: Leakage-free
max. 5 drops/min (0.25 cm³/min) at 350 bar
Media operating temperature range: min. -20 °C to max. +100 °C
Ambient temperature range: min. -20 °C to max. +  60 °C
Operating fluid: Hydraulic oil to DIN 51524 Part 1, 2 and 3
Viscosity range: min. 7.4 mm²/s to max. 420 mm²/s
Filtration: Class 21/19/16 according to ISO 4406 or
cleaner
MTTFd: 150 - 1200 years,
according to DIN EN ISO 13849-1
Installation: No orientation restrictions
Materials: Valve body: free-cutting steel
Piston: hardened and
ground steel
Seals: NBR (standard)
FKM (optional, media
temperature range
-20 °C to +120 °C)
Back-up rings: PTFE
Coil: Steel/Polyamide
Cavity: FC10-2
Weight: Valve complete: 0.37 kg
Coil only: 0.19 kg
The directional valve is a pilot operated Electrical data
valve in poppet style. Response time: energized: approx. 35 ms
When de-energized, there is free flow (at pmax, Qmax, ν = 34 mm²/s) de-energized: approx. 50 ms
through the valve from port 2 to substantially extended response times
port 1. Flow is not possible in the reverse possible at other operating conditions
direction. When the solenoid coil is Type of voltage: DC: direct current solenoid
energized, the valve is closed from port AC: a lternating current solenoid with a
2 to port 1. In the reverse direction the bridge rectifier built into the coil
valve will allow flow from port 1 to 2
Current draw at 20 °C: 1.5 A at 12 V DC
when the hydraulic force on the piston
0.8 A at 24 V DC
overcomes the solenoid force (approx.
Voltage tolerance: ± 15 % of the nominal voltage
EN 5.914.5/11.18

2.5 to 10 bar).
Please mind: In pilot operated solenoid Coil duty rating: Continuous up to max. 115 %
valves, shift performance and response of the nominal voltage at
times depend i.a. very much on pressure 60 °C ambient temperature
drop and volume flow during actuation. Coil type: Coil…-40-1836
* see "Conditions and instructions for valves" in brochure 53.000
1
 DIMENSIONS MODEL CODE
WS10Y – 01  M – C – N – 24  DG
Basic model
Directional poppet valve, UNF
Type
01 = standard
Manual override
no details = without manual override
M = manual override
Body and ports*
hex. 1"
torque*
C = cartridge only
Seals
N = NBR (standard)
V = FKM
Coil voltage
DC voltages
Manual override, with
12 = 12 V DC
HNBR-rubber cap. 24 = 24 V DC
AC voltages (bridge rectifier built into the coil)
115 = 115 V AC
After loosening knurled nut, coil 230 = 230 V AC
can be rotated through 360° and
removed. Other voltages on request
Torque
Coil connectors (type 40-1836)
DC: DG = DIN connector type A to EN 175301-803
without man.

4+1 Nm
DK = KOSTAL threaded connection M27x1
override

*Torque: DL = 2 flying leads, 457 mm long, 0.75 mm²

Steel manifold DN = Deutsch connector, 2-pole, axial
(ultimate tensile strength < 360 N/mm²):
55 Nm
DT = AMP Junior Timer, 2-pole, radial
Aluminium manifold AC: AG = DIN connector type A to EN 175301-803
(ultimate tensile strength < 330 N/mm²): Other connectors on request
45 Nm
(tool acc. to DIN EN ISO 6789,
tool type II class A or B)
For further informations see brochure Standard models
No. 53.000 Model code Part No.
"Conditions and instructions for valves"
WS10Y-01-C-N-24DG 3030653
WS10Y-01-C-N-230AG 3043826
Other models on request
thick

* Standard in-line bodies

millimeter (inch)
subject to technical modifications Code Part No. Material Ports Pressure
FH102-SB4 3037594 Steel, zinc-plated G1/2" 350 bar
FH102-AB4 3037777 Aluminium, anodized G1/2" 210 bar
CAVITY Other housings on request

FC10-2
Seal kits
Code Material Part No.
FS UNF 10/N NBR 3651557
FS UNF 10/V FKM 3651559

TYPICAL PERFORMANCE
fitting depth

Measured at ν = 34 mm²/s, Toil = 46 °C

deenergized
Pressure drop

VE = Visual Examination
* Allowed drilling zone (for manifold design)
** Sharp edges should be avoided by rounding Flow rate
to a radius of 0.1 mm to 0.2 mm
*** largest pre-drilling diameter
(nominal tool diameter)

Form tools
EN 5.914.5/11.18

Note HYDAC Fluidtechnik GmbH

Tool Part No. The information in this brochure relates to the Justus-von-Liebig-Str.
Countersink 176379 operating conditions and applications described. D-66280 Sulzbach/Saar
For applications or operating conditions not Tel: 0 68 97 /509-01
Reamer 165706 described, please contact the relevant
millimeter (inch)
subject to technical modifications technical department. Fax: 0 68 97 /509-598
Subject to technical modifications. E-Mail: [email protected]