इंटरनेट मानक

Disclosure to Promote the Right To Information

Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.

“जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न' 5 तरफ”

Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru
“The Right to Information, The Right to Live” “Step Out From the Old to the New”

IS 2248 (1992): Glossary of terms relating to clay products

for buildings [CED 30: Clay and Stabilized Soil Products
for Construction]

“!ान $ एक न' भारत का +नम-ण”

Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”

“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता ह”

है”
ह
Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
 IS 2248 : 1992
( Reaffirmed 2002 )

( ~FRT q&m)

Indian Standard
GLOSSARY OF TERMS RELATING TO CLAY
PRODUCTS FOR BUILDINGS
( Second Revision )

UDC 691.4 : 001.4

@ BIS 1992

BUREAU OF INDIAN STANDARDS

MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002

January 1992 Price Group 2

Clay Products for Buildings Sectional Committee, CED 30

FOREWORD
This Indian Standard ( Second Revision ) was adopted by the Bureau of Indian Standards, after
the draft finalized by the Clay Products for Buildings Sectional Committee had been approved
by the Civil Engineering Division Council.
Clay products, such as bricks, blocks and tiles, etc, are used abundantly in building work. To
know the properties of such clay products, a clear understanding of the meaning of various
terms is necessary. This glossary has been prepared to fulfil this objective. This standard was
first published in 1969 and subsequently revised in 1981. In this revision the definition of bricks
and blocks have been modified.
In the formulation of this standard, due weightage has been given to international co-ordination
among the standards and practices prevailing in different countries in addition to relating it to
the practices in the field in India.
 IS 2248 : 1992

Indian Standard
GLOSSARY OF TERMS RELATING TO CLAY
PRODUCTS FOR BUILDINGS
( Second Revision )
1 SCOPE or power-driven machmes, such as a hand-screw
press, a soft-mud moulding machine, an extru-
1.1 This standard covers the definition of der or a semi-dry/dry press.
common terms applicable to clay products for
building. 2.2.4 Maturing Temperature - The temperature
2 DEFINITIONS of firing at which the clay body used in the
manufacture of the building material acquires
2.1 ‘Raw Materials the optimum mechanical strength and the
2.1.1 Clay - An earthy or stony mineral necessary physical properties to satisfy the
aggregate consisting essentially of hydr-ous requirements set down in the standard specifi-
silicates of alumina; plastic when sufficiently cations for the relevant building material.
pulverised and wetted: rigid when dry; and 2.2.5 Pugging - This is the process by which
vitreous when fired to a sufficiently high
the lean and plastic clay is tempered before
temperature.
moulding.
2.1.2 Shale - A thinly stratified, consolidated
sedimentary clay with well-marked cleavage 2.2.6 Sanding - The operation of imparting to
parallel to the bedding. the clay product a rough face by blowing sand
on to it, that is, by sand blasting prior to
2.1.3 Surface Clay - An unconsolidated, drying.
unstratified clay, occurring on the surface.
2.2.7 Soaking - The process of imparting heat
2.2 Manufacture to the clay product by maintaining the tempe-
2.2.1 Flashing - The operation of heating the rature constant for a specified period near
clay products with and without air alternately, about the maturing temperature.
where irregularly colourd bricks or tiles are
2.2.8 Tempering - This is the process of mixing
required.
cIay, water and other ingredients, if any, by
2.2.2 Hand Moulding which a homogeneous paste is produced.

2.2.2.1 Ground moulding - When the clay pro- 2.2.9 Weathering - This is the process of
ducts are moulded by hand on ground and the exposing excavated clay mass in the open air,
moulder shifts his position as moulding so that it comes in contact with natural agen-
progresses. cies, such as sun, rain and frost due to which
there is change in some of the physical and
2.2.2.2 Sand moulding - The process of moul- chemical properties that are helpful in subse-
ding of bricks by hand in which fine sand is quent treatment and also impart better working
used to dust the mould before throwing in the properties.
clot.
2.2.2.3 Slop moulding - The process of moul- 2.210 Lime Blowing - If the soil contains lime
ding bricks by hand in which the mould is noduIes or calcarious ‘kankars’ the bricks get
dipped in water, before clay is thrown into it. cracked due to the formation of Calcium
Oxide within the brick mass during firing. The
2.2.2.4 Table moulding - Where bricks are oxides so formed expand after taking moisture
moulded by hand on tabIe and then transported from the air and cause blowing of the bricks.
using pallet boardsIt the drying ground.
2.2.11 Docking - Docking is the process in
2.2.3 Machine Moulding - The process in which which freshly fired bricks are dipped in water
the clay products are shaped in hand-operated to prevent lime blowing.

1
IS 2248 : 1992

2.2.12 Lamination - Lamination is a defect 2.44 Heavy Duty Bricks -’ Bricks required for
normalIy found in the extruded bricks caused masonry in heavy engineering work, such as,
by the differential movement of the clay mass bridge structure, industrial foundations and
when it is pushed by the auger or wing knife multi-storeyed buildings having high durability
of the extrusion machine towards the die of and compressive strength and low water
the machine. If the spacer is too short, there absorption.
may be hollow core in the centre when the
clay mass enters the die. In the die this core 2.4.5 Paving Bricks - Bricks which are used as
is flattened and owing to the rotation of the a paving material for roads, heavy duty indus-
clav it shows in the extruded brick as an ‘S’ trial floors, particularly suited to resist heavy
crack. wear and tear from steel tyred traffic.

2.3 Surface Features 2.4.6 Perforated Bricks - Bricks in which holes

passing through the bricks exceed 25 percent
2.3.1 Combed Finish - Units whose face surfaces of the volume and the holes are sma!l. For the
are altered by more or less parallel scratches in purpose of this definition, a small hole is a hole
manufacture. less than 20 mm wide and less than 500 mm2 in
area. The hole may be circular, square,
2.3.2 Exposed Finish - Units whose surfaces
are intended to be left exposed or painted. rectangular or any other regular shape.
2.4.7 Sewer Bricks - Bricks intended for use
2.3.3 Natural Finish -
Units having unglazed
in the lining of walls, roofs and floors of sewers
or uncoated surface burned to the natural
used for the ordinary sanitary ( domestic)
colour of the material used in forming the
sewage.
body.
2.3.4 .Roughened Finish - Units whose plane die 2.4.8 Soling Bricks - Bricks used for soiing
surfaces are entirely broken by mechanical purpose. They are different from common
building solid bricks.
means.
2.4.9 Wire Cut Bricks - Bricks manufactured
2.3.5 Salt Glaze - Units whose surface faces by cutting an extruding column through a die
have a lustrous glazed finish from the thermo- of weathered and processed clay with the help
chemical reaction of the silicates of the clay of wires fixed to a cutting frame.
body with vapours of common salt and/or other
suitable chemicals. 2.5 Tiles - Burnt clay units which are appre-
ciably smaller in thickness than the bricks and
2.3.6 Sand Finish - Units whose surfaces are are used for flooring, roofing, ceiling and wall
covered with sand. covering.
2.3.7 Smooth Finish - Units whose surface are 2.5.1 Ceiling Tiles ( Plain ) - Clay roofing tiles
not altered or marked in manufacture. which are capable of being used on sloping
roofs below the interlocking plain Mangalore
2.4 Bricks - A masonary unit not exceeding tiles.
300 mm in length, 150 mm in width nor 100 mm
in height. 2.5.2 Flooring Tiles - Clay tiles made by pres-
sing or extrusion and repressing, which are
2.4.1 Acid Resistant Bricks - Bricks used for capable of being laid level on a prepared base.
masonry construction, such as flooring, subject
to acid attack, lining of chambers and towers 2.5.3 Hollow Clay Tiles -Burnt clay units in
in chemical units, lining of sewers carrying which holes passing through the tiles exceed
industrial effluents, etc, to prevent deteriora- 25 percent of the volume and the holes are not
tion of the surface by acids. small. The perforations are parallel to their
length. These tiles can be used both as filler
2.4.2 Common Building Solid Bricks - The burnt material and structural units.
clay building bricks which are commonly used
in building and civil engineering construction 2.5.4 Ridge Tile - A clay roofing tile which is
work in which frogs do not exceed 20 percent capable of being used on the ridge of a sloping
of this volume. roof in conjunction with interlocking plain
Mangalore pattern tiles.
2.4.3 Facing Bricks - Bricks made specially for
facing purpose, that is, which are being exposed 2.5.5 Roo$ngTile, Mangalore Pattern - A type
in use. of clay roofing tile, capable of being laid down

2
 IS 2248 : 1992

on sloping roof by means of nibs which catch 2.7.3 Fired Shrinkage - The percentage reduc-
on the reepers or battens interlock with and tion in length or volume of dry claygtiles or
overlap similar tiles at the lower end on the bricks when subjected to heating to a maturing
sides. temperature of the clay body.
2.5.6 Terracing Tile --- A flat tile, which is 2.7.4 Flexural Strength - A property of solid
capable of being laid level on a prepared base material that indicates its ability to withstand
in one or more courses to provide satisfactory a flexural or transverse load.
floor oriroof finish.
2.7.5 Warpage - Distortion or deformation of
2.6 Blocks - Masonary unit exceeding size of original shape of the clay body during the
a brick in any dimension.
manufacturing”process.
2.6.1 Hollow Block - A block in which holes
passing through the block exceed 25 percent of 2.7.6 Water Absorption - The increase in weight
its volume and the holes are not small. The of a test specimen after immersion in water, at
hollows may belat right angle or parallel to a constant temperature and for a specified
the bearing surface. period, expressed as a percentage of the dry
weight.
2.6.2 Solid Block - A block which is hundred
percent solid. 2.8 General
2.7 Tests 2.8.1 Cells -- Hollow spaces enclosed within
the perimeter of the exterior shells of hollow
2.7.1 Drying Shrinkage - The percentage reduc-
tion in the length or volume of bricks or tiles clay blocks.
on drying, due to the removal of the film of
water which surrounds the individual grains in 2.8.2 Frog - The depression made in one or
the plastic form is given below: both of larger sides of bricks in order to form
a key for the mortar at the joints.
Drying shrinkage, percent = L -L Ld X 100
2.8.3 Perforations - A hollow space of uniform
( wet basis ) section, within a brick, extending from one
where face to the opposite parallel face with its axis
L =wet length in metres, and parallel to the two faces.
Ld = dry length in metres.
2.8.4 Shells - The outer walls of tiles or
2.7.2 EfJIOrescence - A white, yellow or green blocks.
powdry substance occurring on the surface of
the clay product and caused by the migration 2.8.5 Webs - The partition dividing blocks or
of soluble salts, followed by precipitation. tiles into cells.
Standard Mark
The use of the Standard by the provisions of the Bureau of Indian
Mark is governed
Standards Act, 1986 and the Rules and Regulations made thereunder. The Standard Mark
on products covered by an Indian Standard conveys the assurance that they have been
produced to comply with the requirements of that standard under a well defined system
of inspection, testing and quality control which is devised and supervised by BIS and
operated by the producer. Standard marked products are also continuously checked by
BIS for conformity to that standard as a further safeguard. Details of conditions under
which a licence for the use of the Standard Mark may be granted to manufacturers or
producers may be obtained from the Bureau of Indian Standards.
Bureau of Indian Standards

BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to
promote harmonious development of the activities of standardization, marking and quality
certification of goods and attending to connected matters in the country.

Copyright

BIS has the copyright of all its publications. No part of these publications may be reproduced
in any form without the prior permission in writing of BIS. This does not preclude the free use,
in the course of implementing the standard, of necessary details, such as symbols and sizes, type
or grade designations. Enquiries relating to copyright be addressed to the Director
( Publications ), BIS.

Revision of Indian Standards

Indian Standards are reviewed periodically and revised, when necessary and amendments, if
any, are issued from time to time. Users of Indian Standards should ascertain that they are in
possession of the latest amendments or edition. Comments on this Indian Standard may be
sent to BIS giving the following reference:

Dot : No. CED 30 ( 4980 )

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS

Headquarters :
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones : 331 01 31, 331 13 75 Telegrams : Manaksanstha
( Common to all Offices )

Regional Ofices : Telephone

Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg 311 01 31
NEW DELHI 110002 I 331 13 75
Eastern : l/14 C. I. T. Scheme VII M, V. I. P. Road, Maniktola 37 86 62
CALCUTTA 700054
Northern : SC0 445-446, Sector 35-C, CHANDIGARH 160036 53 38 43
Southern :C. I.T. Campus, IV Cross Road, MADRAS 600113 235 02 16
Western : Manakalaya,E9 MIDC, Marol, Andheri ( East ) 6 32 92 95
BOMBAY 400093
Branches : AHMADABAD, BANGALORE, BHOPAL, BHUBANESHWAR, COIMBATORE,
FARIDABAD, GHAZIABAD, GUWAHATI, HYDERABAD, JAIPUR, KANPUR,
PATNA, THIRUVANANTHAPURAM.

Printed at Printwell Printers, Aligarh, India