DELTA IA-PLC As Manual de Programacion

AS Series Programming Manual
Industrial Automation Headquarters

Delta Electronics, Inc.
Taoyuan Technology Center
No.18, Xinglong Rd., Taoyuan District,
Taoyuan City 33068, Taiwan
TEL: 886-3-362-6301 / FAX: 886-3-371-6301
Asia EMEA
Delta Electronics (Shanghai) Co., Ltd. Headquarters: Delta Electronics (Netherlands) B.V.
No.182 Minyu Rd., Pudong Shanghai, P.R.C. Sales: [email protected]
Post code : 201209 Marketing: [email protected]
TEL: 86-21-6872-3988 / FAX: 86-21-6872-3996 Technical Support: [email protected]
Customer Service: 400-820-9595 Customer Support: [email protected]
Service: [email protected]
Delta Electronics (Japan), Inc. TEL: 31(0)40 800 3900
Tokyo Office
Industrial Automation Sales Department BENELUX: Delta Electronics (Netherlands) B.V.
2-1-14 Shibadaimon, Minato-ku De Witbogt 20, 5652 AG Eindhoven, The Netherlands
Tokyo, Japan 105-0012 Mail: [email protected]
TEL: 81-3-5733-1155 / FAX: 81-3-5733-1255 TEL: 31(0)40 800 3900
DACH: Delta Electronics (Netherlands) B.V.

Delta Electronics (Korea), Inc.
Coesterweg 45, D-59494 Soest, Germany
Seoul Office
Mail: [email protected]
1511, 219, Gasan Digital 1-Ro., Geumcheon-gu,
TEL: 49(0)2921 987 0
Seoul, 08501 South Korea
TEL: 82-2-515-5305 / FAX: 82-2-515-5302 France: Delta Electronics (France) S.A.
ZI du bois Challand 2, 15 rue des Pyrénées,
Delta Energy Systems (Singapore) Pte Ltd. Lisses, 91090 Evry Cedex, France
4 Kaki Bukit Avenue 1, #05-04, Singapore 417939 Mail: [email protected]
TEL: 65-6747-5155 / FAX: 65-6744-9228 TEL: 33(0)1 69 77 82 60
Delta Electronics (India) Pvt. Ltd. Iberia: Delta Electronics Solutions (Spain) S.L.U
AS Series
Plot No.43, Sector 35, HSIIDC Gurgaon, Ctra. De Villaverde a Vallecas, 265 1º Dcha Ed.
PIN 122001, Haryana, India Hormigueras – P.I. de Vallecas 28031 Madrid
TEL: 91-124-4874900 / FAX : 91-124-4874945 TEL: 34(0)91 223 74 20
Carrer Llacuna 166, 08018 Barcelona, Spain
Programming Manual
Delta Electronics (Thailand) PCL.
909 Soi 9, Moo 4, Bangpoo Industrial Estate (E.P.Z), Mail: [email protected]
Pattana 1 Rd., T.Phraksa, A.Muang, Italy: Delta Electronics (Italy) S.r.l.
Samutprakarn 10280, Thailand Via Meda 2–22060 Novedrate(CO)
TEL: 66-2709-2800 / FAX : 662-709-2827 Piazza Grazioli 18 00186 Roma Italy
Delta Electronics (Australia) Pty Ltd. TEL: 39 039 8900365
Unit 20-21/45 Normanby Rd., Notting Hill Vic 3168, Australia
TEL: 61-3-9543-3720 Russia: Delta Energy System LLC
Vereyskaya Plaza II, office 112 Vereyskaya str.
Americas 17 121357 Moscow Russia
Delta Electronics (Americas) Ltd.
TEL: 7 495 644 3240
Raleigh Office
P.O. Box 12173, 5101 Davis Drive, Turkey: Delta Greentech Elektronik San. Ltd. Sti. (Turkey)
Research Triangle Park, NC 27709, U.S.A. Şerifali Mah. Hendem Cad. Kule Sok. No:16-A
TEL: 1-919-767-3813 / FAX: 1-919-767-3969 34775 Ümraniye – İstanbul
Delta Electronics Brazil TEL: 90 216 499 9910
São Paulo Sales Office
Rua Itapeva, 26 - 3°, andar Edificio Itapeva, GCC: Delta Energy Systems AG (Dubai BR)
One - Bela Vista 01332-000 - São Paulo - SP - Brazil P.O. Box 185668, Gate 7, 3rd Floor, Hamarain Centre
TEL: 55-12-3932-2300 / FAX: 55-12-3932-237 Dubai, United Arab Emirates
Delta Electronics International Mexico S.A. de C.V. TEL: 971(0)4 2690148
Mexico Office
Gustavo Baz No. 309 Edificio E PB 103 Egypt + North Africa: Delta Electronics
Colonia La Loma, CP 54060 Unit 318, 3rd Floor, Trivium Business Complex, North 90 street,
Tlalnepantla, Estado de México New Cairo, Cairo, Egypt
TEL: 52-55-3603-9200 Mail: [email protected]
AS-0249720-07
*We reserve the right to change the information in this catalogue without prior notice. 2020/12/08 www.deltaww.com
Revision History
Ve r s i o n Revision Date
1st The first version was published. 2 0 1 6 / 11 / 3 0

1. Updated information in section 2.1.1, 2.2.7, 2.2.8, 2.2.14,
2.2.16.
2nd 2. Added new instructions in Chapter 3. 2018/05/07
3. Updated and added new instructions in Chapter 6.
4. Updated information in Chapter 7.
1. Updated SM information in section 2.1.1.
2.Updated S M information including SM784-815, S M896-927,
S M1440-1447 and added S M478-479, S M498-4 99, S M518-
519, S M538-539, S M55 8-559, S M578-579, S M1 581-1608,
S M 1 6 11 - 1 6 1 8 , S M 1 6 2 1 - 1 6 2 8 ,
S M1683-1684, and S M1691-1698SM in sections 2.2.7.
3.Updated the table of SM refresh time and added new SM
refresh time in the table in section 2.2.8.
4.Updated SR182-183, SR217-218, SR424, SR825-893,
SR1336, and SR1376 in section 2.2.14.
5.Added SR187-188, SR478-479, SR498-499,SR518-519,
SR538-539, SR558-559, SR578-579, SR640-651, SR751-758,
and SR761-768 in section 2.2.14.
6.Updated descriptions in point 4 Communication functions,
point 14 S curve mode and point 18 Flags and registers
c o n c e r n i n g d a t a e xc h a n g e . A d d e d p o i n t 1 5 B a c k l a s h
compensation function in section 2.2.16.
3rd 7.Added new instructions on the lists in Chapter 3. 2018/05/22
8.Added new instructions in Chapter 6: API0222, API0601,
A P I 0 7 11 , A P I 1 0 1 2 , A P I 1 0 1 3 , A P I 1 2 2 6 , A P I 1 4 0 2 , A P I 1 4 0 3 ,
API1404, API1405, API1406, API1407, API08,
API1409,API1410, API1415, API1416, API1818, API1819,
A P I 1 8 2 0 , A P I 1 9 0 6 , A P I 2 1 2 2 , A P I 2 1 2 3 , A P I 2 2 11 , A P I 2 2 1 2 ,
A P I 2 8 0 8 , A P I 2 8 0 9 , A P I 2 8 1 0 , a n d A P I 2 8 11 .
9.Updated instructions in Chapter 6: API0222, API0600,
API0702, API0708, API0709, API0710, API1004, API1601,
API1607, API1808,API1812, API1814, API1815, API1816,
API1817, API2200, API2200-2203, API2208, API2210,
A P I 2 7 0 6 , A P I 2 7 0 7 , A P I 2 7 0 8 , A P I 2 7 0 9 , A P I 2 7 1 0 , A P I 2 7 11 ,
API2803, API2804, API2805, API2806, API2807 and API2808.
10.Updated solutions for errors including codes 7203,
8105, 8106 and 8107.
1. Manual corrections on the unit used in SR182, 183, 185,
4th 2018/06/12
210, 213, 421, 422, 423, and 424.
5th 1. Added AS300/AS200 Series CPU module descriptions 2019/5/10
in section 1.1.2 Model Description.

2. A d d e d a n d u p d a t e d S M a n d S R i n C h a p t e r 2 : S M2 3 0 -
S M 2 6 1 , S M 5 8 5 - S M 5 8 7 , S M 111 0 , S M 1 6 8 5 , S R 6 5 2 - S R 6 5 5 ,
SR791-SR806, SR811-SR818, SR823-SR824, SR1015,
S R 1 5 2 0 - S R 1 5 4 0 , S R 1 5 5 9 - S R 1 5 9 2 , S M7 6 - S M 9 1 , S M 1 6 8 -
S M 1 7 1 , S M 4 5 5 , S M 1 0 0 6 - S M 1 0 3 1 , S M 11 8 4 - S M 11 9 9 ,
S M1216-S M1231, S M12 48-S M1263, S M1271-S M1299,
S M1424-S M1439, S M16 81, S M1709-S M1919, S R166-
SR179, SR182-SR183, SR187-SR188, SR215-SR216,
SR1000-SR1014, and SR1435-SR1511.
3. Added and updated instructions in Chapter 3: API0602,
A P I 1 4 1 7 , A P I 2 3 0 4 , A P I 2 7 2 4 , A P I 2 8 1 2 - A P I 2 8 1 6 , A P I 0 7 11 ,
A P I 111 0 , A P I 1111 , A P I 1 4 0 2 , A P I 1 4 0 7 , A P I 1 4 0 8 , a n d
API1416.
4. Added information of using index registers in interrupt
instructions in section 4.4.
5. Updated instructions in Chapter 5: PED, APED, OPED,
N E D , A N E D , O N E D , P L S a n d P L F.
6. Updated instructions in Chapter 6: API0602, API1417,
API2304, API2724, API2812-API2816, API0018-API0023,
A P I 0 7 0 8 - A P I 0 7 11 , A P I 1 0 0 4 - A P I 1 0 0 7 , A P I 111 0 , A P I 1111 ,
API1226, API1402-API1410, API1415-API1416, API1816,
API2200, API2201, API2203, API2208, API2210-API2212,
API2300-API2302, API2704, API2706-API2709, API2712-
API2716, API2719,
API2800, API2803, API2805 and API2807.
7. Updated emergency information in section 7.3.1 and
7.3.2. Added error codes 2030 and 2031.
1. Manual corrections on the descriptions of function codes
K5566 and K5577 of SR36 and SR412 and SR415 in
Chapter 2.
2. Updated the descriptions in SM1375~S M1447 i n Chapter
2.
3. Updated the descriptions in SR1000~SR1006 in Chapter
2.
4. Updated the descriptions in the error code 16#00xx in
Chapter 2.
6th 2019/6/21
5. Added a maximum input frequency table in DCNT
instruction (API1004) in Chapter 6.
6. U p d a t e d t h e a c c e p t a b l e i n p u t r a n g e f o r S 1 i n PW D
7. Updated the alignment mark function charts in DDRVM
8. Added an example of using abort symbols and completion
flags in TPO instruction (API2718) in Chapter 6.
1. Updated description on AS300, AS200, AS02, 04PU-A in

Section 1.1.2.
7th 2020/12/08
2. Added new production information AS100, AS02HC-A,
AS04SIL-A, AS-FPFN02 and AS-FOPC02 in Chapter 1.
3. U p d a t e R e l a t i o n B e t w e e n t h e P L C A c t i o n a n d D e v i c e Ty p e
in Section 2.1.3. Added AS100 information updated
S M1375~S M1477 and added SM1448~1455, S M1686 in
S e c t i o n 2 . 2 . 7 S p e c i a l A u xi l i a r y R e l a y s ( S M ) a n d S e c t i o n
2.2.14 Special Data Registers (SR). Added CNT instruction
i n f o r m a t i o n i n S e c t i o n 2 . 2 . 11 C o u n t e r s . A d d e d D C N T
instruction information in Section 2.2.12 32-bit counters
(HC). Added frequently mapped registers information in
Section 2.2.13. Added new Special Data Registers (SR):
SR42, SR48, SR54, SR60, SR66, SR72, SR78, SR84, SR90,
S R 9 6 , S R 1 0 2 , S R 1 0 8 , S R 11 4 , S R 1 2 0 , S R 1 2 6 , S R 1 3 2 ,
SR138, SR144, SR150, SR156, SR405, SR406 and delete
SR1540 in Section 2.2.14. Added #2 error codes in
S M27/SR27, updated #22 information in Flags
S M230~S M261, updated #7 PLC error log information,
added #24 Auto-reset flags for pulse output in Section
2.2.16.
4. Added and updated instructions in Chapter 3: API1014,
API1015, API1227, API1418-API1423, API1821, API2817,
A P I 2 8 1 8 , A P I 11 0 2 - A P I 11 0 8 , A P I 111 4 , A P I 111 5 , A P I 2 8 0 6 ,
API1415.
5. A d d e d a s e c t i o n e xp l a i n i n g w h i c h i n s t r u c t i o n s h o u l d b e
used in Ladder Programming Language in section 4.3.
6. All the instructions in this manual does NOT support the
d a t a t y p e U I N T. R e m o v e U I N T f r o m t h e s u p p o r t i n g l i s t i n
Chapter 6. Updated instructions in Chapter 6: API0202,
A P I 1 0 0 7 , A P I 1 0 0 9 , A P I 11 0 2 - A P I 11 0 8 , A P I 111 4 , A P I 111 5 ,
A P I 1 4 1 7 , A P I 1 5 0 1 - A P I 1 5 0 4 , A P I 1 8 0 8 , A P I 2 1 0 6 , A P I 2 11 6 ,
A P I 2 11 7 , A P I 2 11 9 , A P I 2 2 0 0 , A P I 2 2 0 4 , A P I 2 2 0 8 , A P I 2 2 0 9 ,
API2718, API2800, API2803, API2806, API2812-API2815.
Added new instructions in Chapter 6: API1014, API1015,
API1227, API1418-API1423, API1426, API1427, API1821,
API2817 and API2818.
7. Added an explanation about Step Position in Section 7.1.4.
8. Updated error codes 2001-2027 in Section 7.2.8 and 7.2.9.
Updated the ERROR LED indicators blinking time to every
0.2 seconds for AIO modules and AS02LC in Section 7.3.1.
Added error codes 16#1500 and 16#1505 for AS00SCM in
Section 7.3.4.
Table of Contents
Chapter 1 Introduction
1.1 Overview ............................................................................................... 1-2

1.1.1 Related Manuals ............................................................................ 1-2
1.1.2 Model Description .......................................................................... 1-2
1.2 Software .............................................................................................. 1-10

1.2.1 Program Editor ............................................................................ 1-10
1.2.2 Program Organization Units and Tasks ............................................ 1-12
Chapter 2 Devices
2.1 Introduction to Devices ......................................................................... 2-2

2.1.1 Device Table .................................................................................. 2-2
2.1.2 Basic Structure of I/O Storage ......................................................... 2-3
2.1.3 Relation Between the PLC Action and the Device Type ........................ 2-3
2.1.4 Latched Areas in the Device Range................................................... 2-4
2.2. Device Functions .................................................................................. 2-5

2.2.1 Values and Constants ..................................................................... 2-5
2.2.2 Floating-point Numbers .................................................................. 2-7
2.2.2.1 Single-precision Floating-point Numbers .......................................... 2-7
2.2.2.2 Decimal Floating-point Numbers ..................................................... 2-8
2.2.3 Strings ......................................................................................... 2-8
2.2.4 Input Relays (X) ............................................................................ 2-9
2.2.5 Output Relays (Y) ........................................................................ 2-10
2.2.6 Auxiliary Relays (M) ..................................................................... 2-10
2.2.7 Special Auxiliary Relays (SM)......................................................... 2-11
2.2.8 Refresh Time for Special Auxiliary Relays ........................................ 2-62
2.2.9 Stepping Relays (S) ..................................................................... 2-70
2.2.10 Timers (T)................................................................................... 2-70
2.2.11 Counters ..................................................................................... 2-72
2.2.12 32-bit Counters (HC) .................................................................... 2-73
2.2.13 Data Registers (D) ....................................................................... 2-75
2.2.14 Special Data Registers (SR)........................................................... 2-76
2.2.15 Special Data Registers Refresh Conditions ...................................... 2-115
2.2.16 Additional Remarks on Special Auxiliary Relays and Special Data
Registers………………………………………………………………………………………………..2-118
2.2.17 Index Register (E) ....................................................................... 2-144
2.2.18 File Registers (FR) ....................................................................... 2-144
i
Chapter 3 Instruction Tables
3.1 Types of Instructions ........................................................................ 3-2

3.1.1 Basic Instructions .......................................................................... 3-2
3.1.2 Applied Instructions ....................................................................... 3-2
3.2 Understanding Instruction Tables ..................................................... 3-3

3.2.2 Applied Instructions (Sorted numerically) ......................................... 3-4
3.2.3 Applied Instructions (Sorted Alphabetically) ...................................... 3-5
3.2.4 Device Tables ................................................................................ 3-6
3.3 Lists of Basic Instructions ................................................................. 3-7
3.4 Lists of Applied Instructions .............................................................. 3-9

3.4.1 Applied Instructions (Sorted numerically by API number) ................... 3-9
3.4.2 Applied Instructions (Sorted Alphabetically) ..................................... 3-44
Chapter 4 Instruction Structure
4.1 Applied Instructions - API Description .............................................. 4-2
4.2 Operand Usage Description ............................................................... 4-4
4.3 Restrictions on the Use of Instructions ............................................. 4-7
4.4 Index Registers ................................................................................. 4-9
4.5 Pointer Registers ............................................................................. 4-12
4.6 Pointer Registers of Timers ............................................................. 4-14
4.7 Pointer Registers for 16-bit Counters .............................................. 4-16
4.9 File Register .................................................................................... 4-20
Chapter 5 Basic Instructions
5.1 List of Basic Instructions ................................................................... 5-2
5.2 Basic Instructions ............................................................................. 5-3
ii
Chapter 6 Applied Instructions
6.1 Comparison Instructions ....................................................................... 6-4

6.1.1 List of Comparison Instructions ............................................................. 6-4
6.1.2 Explanation of Comparison Instructions ................................................. 6-7
6.2 Arithmetic Instructions ....................................................................... 6-46

6.2.1 List of Arithmetic Instructions ............................................................. 6-46
6.2.2 Explanation of Arithmetic Instructions ................................................. 6-47
6.3 Data Conversion Instructions .............................................................. 6-78

6.3.1 List of Data Conversion Instructions .................................................... 6-78
6.3.2 Explanation of Data Conversion Instructions ......................................... 6-79
6.4 Data Transfer Instructions ................................................................ 6-121

6.4.1 List of Data Transfer Instructions ....................................................... 6-121
6.4.2 Explanation of Data Transfer Instructions ............................................ 6-122
6.5 Jump Instructions ............................................................................. 6-149

6.5.1 List of Jump Instructions ................................................................... 6-149
6.5.2 Explanation of Jump Instructions ....................................................... 6-150
6.6 Program Execution Instructions ........................................................ 6-158

6.6.1 List of Program Execution Instructions ................................................ 6-158
6.6.2 Explanation of Program Execution Instructions..................................... 6-159
6.7 IO Refreshing Instructions ................................................................ 6-171

6.7.1 List of IO Refreshing Instructions ....................................................... 6-171
6.7.2 Explanation of IO Refreshing Instructions ............................................ 6-172
6.8 Miscellaneous Instructions ................................................................ 6-179

6.8.1 List of Convenience Instructions......................................................... 6-179
6.8.2 Explanation of Convenience Instructions ............................................. 6-180
6.9 Logic Instructions .............................................................................. 6-233

6.9.1 List of Logic Instructions ................................................................... 6-233
6.9.2 Explanation of Logic Instructions ........................................................ 6-234
6.10 Rotation Instructions ....................................................................... 6-255

6.10.1 List of Rotation Instructions ............................................................. 6-255
6.10.2 Explanation of Rotation Instructions ................................................. 6-256
6.11 Timer and Counter Instructions ....................................................... 6-267

6.11.1 List of Timer and Counter Instructions .............................................. 6-267
6.11.2 Explanation of Timer and Counter Instructions ................................... 6-268
6.12 Shift Instructions............................................................................. 6-310

6.12.1 List of Shift Instructions .................................................................. 6-310
iii
6.12.2 Explanation of Shift Instructions ...................................................... 6-311
6.13 Data Processing Instructions .......................................................... 6-352

6.13.1 List of Data Processing Instructions .................................................. 6-352
6.13.2 Explanation of Data Processing Instructions ...................................... 6-353
6.14 Structure Creation Instructions ....................................................... 6-414

6.14.1 List of Structure Creation Instructions .............................................. 6-414
6.14.2 Explanation of Structure Creation Instructions ................................... 6-415
6.15 Module Instructions ........................................................................ 6-423

6.15.1 List of Module Instructions .............................................................. 6-423
6.15.2 Explanation of Module Instructions ................................................... 6-424
6.16 Floating-point Number Instructions ................................................ 6-526

6.16.1 List of Floating-point Number Instructions ......................................... 6-526
6.16.2 Explanation of Floating-point Number Instructions ............................. 6-527
6.17 Real-time Clock Instructions ........................................................... 6-562

6.17.1 List of Real-time Clock Instructions .................................................. 6-562
6.17.2 Explanation of Real-time Clock Instructions ....................................... 6-563
6.18 Peripheral Instructions.................................................................... 6-594

6.18.1 List of Peripheral Instructions .......................................................... 6-594
6.18.2 Explanation of Peripheral Instructions ............................................... 6-595
6.19 Communication Instructions ........................................................... 6-611

6.19.1 List of Communication Instructions................................................... 6-611
6.19.2 Explanation of Communication Instructions ....................................... 6-612
6.19.3 Descriptions on the Communication-related Flags and Registers .......... 6-699
6.20 Other Instructions ........................................................................... 6-703

6.20.1 List of Other Instructions ................................................................ 6-703
6.20.2 Explanation of Other Instructions ..................................................... 6-704
6.21 String Processing Instructions ........................................................ 6-716

6.21.1 List of String Processing Instructions ................................................ 6-716
6.21.2 Explanation of String Processing Instructions ..................................... 6-717
6.22 Ethernet Instructions ...................................................................... 6-780

6.22.1 List of Ethernet Instructions ............................................................ 6-780
6.22.2 Explanation of Ethernet Instructions ................................................. 6-781
6.23 Memory Card Instructions ............................................................... 6-822

6.23.1 List of Memory Card Instructions...................................................... 6-822
6.23.2 Explanation of Memory Card Instructions .......................................... 6-823
iv
6.24 Task Control Instructions ................................................................ 6-843
6.24.1 List of Task Control Instructions ....................................................... 6-843
6.24.2 Explanation of Task Control Instructions ............................................ 6-844
6.25 SFC Instructions .............................................................................. 6-848

6.25.1 List of SFC Instructions ................................................................... 6-848
6.25.2 Explanation of SFC Instructions ........................................................ 6-849
6.26 High-speed Output Instructions ...................................................... 6-856

6.26.1 List of High-speed Output Instructions .............................................. 6-856
6.26.2 Explanation of High-speed Output Instructions................................... 6-857
6.27 Delta CANopen Communication Instructions ................................... 6-970

6.27.1 List of Delta CANopen Communication Instructions ............................. 6-970
6.27.2 Explanation of Delta CANopen Communication Instructions ................. 6-971
6.27.3 Frequently asked questions in Delta special CANopen communication and
Troubleshooting ..................................................................................... 6-1040
Chapter 7 Troubleshooting
7.1 Troubleshooting ................................................................................ 7-2

7.1.1 Basic troubleshooting steps ............................................................. 7-2
7.1.2 Clear the Error States ..................................................................... 7-2
7.1.3 Troubleshooting SOP ...................................................................... 7-3
7.1.4 System Log and Positions of the Error Step ....................................... 7-4
7.2 Troubleshooting for CPU Modules ..................................................... 7-6
7.2.1 ERROR LED Indicators Are ON ......................................................... 7-6
7.2.2 ERROR LED Indicators Blinking Every 0.5 Seconds ............................. 7-6
7.2.3 ERROR LED Indicators Blinking Rapidly Every 0.2 Seconds .................. 7-8
7.2.4 ERROR LED Indicators Slow Blinking Every 3 Seconds and Lighting up for
1 Second ...................................................................................... 7-8
7.2.5 BAT. LOW LED Indicators Are ON...................................................... 7-8
7.2.6 BAT. LOW LED Indicators Blinking Every 0.5 Seconds ......................... 7-8
7.2.7 The LED RUN and ERROR Indicators are Blinking Simultaneously
Every 0.5 Seconds ......................................................................... 7-9
7.2.8 The RUN and LED Indicators are Blinking One After Another Every
0.5 Seconds. ................................................................................. 7-9
7.2.9 Other Errors (Without LED Indicators) .............................................. 7-9
7.3 Troubleshooting for I/O Modules .................................................... 7-15
7.3.1 Troubleshooting for Analog Modules (AD/DA/XA) and Temperature
Modules (RTD/TC) ........................................................................ 7-15
7.3.2 Troubleshooting for the Load Cell Module AS02LC ............................ 7-17
7.3.3 Troubleshooting for the Module AS00SCM as a Communication Module 7-17
7.3.4 Troubleshooting for the Module AS00SCM as a Remote Module .......... 7-19
v
7.4 Error Codes and LED Indicators for CPU Modules ............................ 7-20
7.4.1 Error Codes and LED Indicators for CPU Modules .............................. 7-21
7.4.2 Error Codes and LED Indicators for Analog/Temperature Modules........ 7-26
7.4.3 Error Codes and LED Indicators for Load Cell Module AS02LC ............. 7-27
7.4.4 Error Codes and LED Indicators for Module AS00SCM as a Communication
Module ........................................................................................ 7-27
7.4.5 Error Codes and LED Indicators for Module AS00SCM as a Remote
Module ........................................................................................ 7-28
vi
1
Chapter 1 Introduction
Table of Contents
1.1 Overview ............................................................................................... 1-2
1.1.1 Related Manuals ............................................................................ 1-2
1.1.2 Model Description .......................................................................... 1-2
1.2 Software .............................................................................................. 1-10

1.2.1 Program Editor .............................................................................1-10
1.2.2 Program Organization Units and Tasks.............................................1-12
1-1
A S S er i es Pr og r am m ing M an u a l
1.1 Overview
_1 This manual introduces you to programming the AS Series programmable logic controllers, the basic instructions, and
the applied instructions.
1.1.1 Related Manuals

The related manuals for the AS Series programmable logic controllers are listed below.
 AS Series Quick Start
This guides you in getting started with the system before you read the other related manuals.
 AS Series Programming Manual (this manual)
This introduces you to programming the AS Series programmable logic controllers, the basic instructions, and the
applied instructions.
 ISPSoft User Manual
This introduces the ISPSoft software that you use to program the AS Series programmable logic controllers. It
describes the programming languages (ladder diagrams, instruction lists, sequential function charts, function block
diagrams, and structured texts), the concept of POUs, and the concept of tasks.
 AS Series Hardware Manual
This introduces the electrical specifications, appearances, dimensions, and other features of the hardware.
 AS Series Operation Manual
This introduces the functions of CPUs, devices, module tables, troubleshooting, and other operating features.
 AS Series Module Manual
This introduces the use of the special I/O modules; for example: network modules, analog I/O modules, temperature
measurement modules, and others.
1.1.2 Model Description

Classification Model Name Description
Input: 100-240 VAC, 50/60 Hz
AS-PS02
Output: 24VDC/2A, 48W (for PLC internal use)
Power supply
Input: 100-240 VAC, 50/60 Hz
module
AS-PS02A Output: 24VDC/1.5A, 36W (for PLC internal use)
Output: 24VDC/0.5A, 12W (for external use)
CPU module, 24VDC power input, PNP output, 1x Ethernet port, 2x
RS-485 ports, 1x USB port, 1x Micro SD interface, 2x function cards
AS332P-A
(optional), supporting 32 I/Os (16DI+16DO) and up to 1024 I/Os.
Program capacity:128K steps, high-density terminal blocks
CPU module, 24VDC power input, NPN output, 1x Ethernet port, 2x
AS300 Series
CPU module AS332T-A
Program capacity:128K steps, high-density terminal blocks
CPU module, 24VDC power input, NPN differential output, 1x
AS324MT-A Ethernet port, 2x RS-485 ports, 1x USB port, 1x Micro SD interface,
2x function cards (optional), supporting 24 I/Os (12DI+12DO) and up
1-2
C ha pt er 1 I ntr o duc t i on
1_
to 1016 I/Os. Program capacity:128K steps, high-density terminal
blocks
CPU module, 24VDC power input, PNP output, 1x Ethernet port , 2x
AS320P-B
Program capacity:128K steps, removable terminal blocks
CPU module, 24VDC power input, NPN output, 1x Ethernet port, 2x
AS320T-B
Program capacity:128K steps, removable terminal blocks
CPU module, 24VDC power input, no I/Os, 1x Ethernet port, 2x RS-
485 ports, 1x USB port, 1x Micro SD interface, 2x function cards
AS300N-A
(optional), and supporting up to 1024 I/Os. Program capacity:128K
steps
CPU module, 24VDC power input, PNP output, 1x Ethernet port , 2x
RS-485 ports, 1x USB port, 1x Micro SD interface, CAN
AS228P-A
communication port, supporting 28 I/Os (16DI+12DO) and up to 1024
I/Os. Program capacity: 64K steps, removable terminal blocks
CPU module, 24VDC power input, NPN output, 1x Ethernet port , 2x
AS228T-A
CPU module, 24VDC power input, Relay output, 1x Ethernet port , 2x
AS228R-A
AS200 Series I/Os. Program capacity: 64K steps, removable terminal blocks
CPU module CPU module, 24VDC power input, PNP output, 1x Ethernet port , 2x
AS218PX-A
communication port, supporting 18 I/Os (8DI+6DO+2AI+2AO) and up
to 1024 I/Os. Program capacity: 64K steps, removable terminal blocks
CPU module, 24VDC power input, NPN output, 1x Ethernet port , 2x
AS218TX-A
CPU module, 24VDC power input, Relay output, 1x Ethernet port , 2x
AS218RX-A
CPU module, 100-240 VAC power input, PNP output, 1x Ethernet
port, 2x RS-485 ports, 1x USB port, 1x Micro SD interface, CAN
AS132P-A
I/Os. Program capacity:64K steps, removable terminal blocks
CPU module, 100-240 VAC power input, NPN output, 1x Ethernet
port , 2x RS-485 ports, 1x USB port, 1x Micro SD interface, CAN
AS132T-A
AS100 Series communication port, supporting 32 I/Os (16DI+16DO) and up to 1024
CPU module I/Os. Program capacity: 64K steps, removable terminal blocks
CPU module, 100-240 VAC power input, Relay output, 1x Ethernet
AS132R-A
AS148P-A
1-3
_1 communication port, supporting 48 I/Os (24DI+24DO) and up to 1024

AS148T-A
AS148R-A
AS164P-A
AS164T-A
AS164R-A
24VDC
5mA
AS08AM10N-A
8 inputs
Spring-clamp terminal block
5 - 30VDC
0.5A/output, 4A/COM
AS08AN01P-A 8 outputs
Sourcing output
240VAC/24VDC
2A/output, 8A/COM
AS08AN01R-A 8 outputs
Relay
Digital
input/output
module 5 - 30VDC
0.5A/output, 4A/COM
AS08AN01T-A 8 outputs
Sinking output
24VDC
5mA
AS16AM10N-A
16 inputs
5 - 30VDC
0.5A/output, 4A/COM
AS16AN01P-A 16 outputs
Sourcing output
1-4

240VAC/24VDC
2A/output, 8A/COM
1_
AS16AN01R-A 16 outputs
Relay
5 - 30VDC
0.5A/output, 4A/COM
Sinking output
24VDC
5mA
8 inputs
5 - 30VDC
AS16AP11P-A
0.5A/output, 4A/COM
8 outputs
Sourcing output
24VDC
5mA
8 inputs
240VAC/24VDC
AS16AP11R-A
2A/output, 8A/COM
8 outputs
Relay
24VDC
5mA
8 inputs
5 - 30VDC
AS16AP11T-A
0.5A/output, 4A/COM
8 outputs
Sinking output
24VDC
3.2mA
AS32AM10N-A
32 inputs
MIL connector
5 - 30VDC
0.1A/output, 3.2A/COM
Sinking output
MIL connector
24VDC
3.2mA
AS64AM10N-A
64 inputs
MIL connector
5 - 30VDC
AS64AN02T-A
0.1A/output, 3.2A/COM
1-5
_1 64 outputs
Sinking output
MIL connector
4-channel analog input module
Hardware resolution: 16 bits
AS04AD-A
0–10V, 0/1–5V, -5 to +5V, -10 to +10V, 0/4–20mA, -20–+20mA
Conversion time: 2 ms/channel
AS08AD-B
0 to +10V, 0/1–5V, -5V to +5V, -10V to +10V
AS08AD-C
0/4–20mA, -20mA–+20mA
Analog
input/output
module 4-channel analog output module
AS04DA-A
-10 to +10V, 0–20mA, 4–20mA
4-channel analog input
0–10V, 0/1–5V, -5 to +5V, -10 to +10V, 0/4–20mA, -20 to +20mA
AS06XA-A
2-channel analog output
-10 to +10V, 0–20mA, 4–20mA
4-channe, 2-wire/3-wire RTD
Sensor type: Pt100 / Ni100 / Pt1000 / Ni1000 / JPt100 / LG-Ni1000 /
AS04RTD-A Cu50 / Cu100 / 0-300Ω / 0-3000Ω input impedance
Resolution: 0.1°C/0.1°F (16 bits)
Conversion time: 200ms/channel
6-channe, 2-wire/3-wire RTD
Sensor type: Pt100 / Ni100 / Pt1000 / Ni1000 / JPt100 / LG-Ni1000 /
AS06RTD-A Cu50 / Cu100 / 0-300Ω / 0-3000Ω input impedance, Resolution:
Temperature 0.1°C/0.1°F (16 bits)
measurement Conversion time: 200ms/channel
module
4-channel thermocouple
Sensor type: J, K, R, S, T, E, N, B and -100 to +100 mV
AS04TC-A
8-channel thermocouple
Sensor type: J, K, R, S, T, E, N, B and -100 to +100 mV
AS08TC-A
2-channel, 4-wire/6-wire load cell sensor
Load cell Eigenvalues for a load cell: 1, 2, 4, 6, 20, 40, 80 mV/V
AS02LC-A
module Highest precision 1/10000 @ 50ms of conversion time
ADC Resolution : 4 bits
1-6
1_
Conversion time: 2.5–400ms (nine options to choose from)
2-axis motion control,
5-24 VDC, 1 differential input (A/B/Z phase ),
maximum hardware input bandwidth at 200 k Hz
AS02PU-A 24 VDC, 5 mA, 5 inputs,
maximum hardware input bandwidth at 1 k Hz
Positioning 5 VDC, 2-axis, 4 differential outputs,
module high-speed output frequency at 200 k Hz
4-axis motion control
24 VDC, 5mA, 6 outputs,
AS04PU-A maximum hardware input bandwidth at 1 k Hz
5-30 VDC, 0.1A, 4-axis, 8 NPN outputs,
maximum high-speed frequency at 100 kHz
2-channel high-speed counters
Input methods for the 2-channel are pulse-input (max. at 200 kHz)
and
Counter
AS02HC-A SSI communication interface input (max. at 1.25 MHz)
module
Incrementing / decrementing encoder input
4-point high-speed open collector output, 5-30 VDC, 0.1A,
work with high speed differential output
Serial communication module, 2x communication ports for
AS00SCM-A
Network communication cards, supporting MODBUS protocols
module AS01DNET-A DeviceNet communication port, functioning as master or slave
AS04SIL-A IO-Link module, built-in with 4 IO-Link communication ports
AS00SCM-A
+ For AS-FCOPM function cards
AS-FCOPM
AS00SCM-A
Remote I/O
+ For AS-FEN02 function cards
module
AS-FEN02
DeviceNet remote IO slave, its right side connectswith AS Series
AS01DNET-A (RTU) extension modules, including digital modules, analog modules,
temperature modules, etc.
AS-F232 Serial communication port, RS232, functioning as master or slave
CANopen communication port, supporting DS301, AS series remote
AS-FCOPM
modules and Delta servo systems
2-channel analog input
AS-F2AD 0-10V (12 bits), 4-20mA (11 bits)
Function cards
2-channel analog output
AS-F2DA 0-10V, 4-20mA (12 bits)
2x Ethernet ports, supporting MODBUS TCP, EtherNet/IP Adapter, AS
AS-FEN02
Series remote control, and DLR function
2x Ethernet ports, supporting data exchange, supporting PROFINET
AS-FPFN02
Device (adapter)
2x Ethernet ports, supporting data exchange, supporting OPC UA
AS-FOPC02
Server, only available for AS300 Series PLC CPU
1-7
_1 UC-PRG015-01A
(1.5M)
Used for the connection between a PLC and a PC via a mini USB
port, use for AS332T-A, AS332P-A and AS324MT-A
UC-PRG030-01A Use for the connection between a PLC and a PC with a mini USB
Programming
port, use for AS332T-A, AS332P-A and AS324MT-A
cable (3M)
Use for the connection between a PLC and a PC with a RJ45 port,
UC-PRG030-20A
use for AS332T-A, AS332P-A, AS324MT-A, AS-FEN02 and AS-
(3M) FPFN02
UC-ET010-24B (1M)
MIL connector, 40Pin ↔ 40Pin, shielded, use for AS32AM10N-A,
UC-ET020-24B (2M)
AS32AN02T-A, AS64AM10N-A and AS64AN02T-A
I/O extension UC-ET030-24B (3M)
cable UC-ET010-24D (1M) MIL connector, 40Pin↔ 2x 20Pin, shielded, use for AS332T-A,
UC-ET020-24D (2M) AS332P-A, AS324MT-A, AS32AM10N-A, AS32AN02T-A,
UC-ET030-24D (3M) AS64AM10N-A, and AS64AN02T-A
16 inputs/outputs, 20-Pin MIL connector, use for AS332T-A, AS332P-
UB-10-ID16A A, AS324MT-A, AS32AM10N-A, AS32AN02T-A, AS64AM10N-A and
AS64AN02T-A
32 inputs, 40-Pin MIL connector, use for AS32AM10N-A and
UB-10-ID32A
AS64AM10N-A
External Terminal block (spring clamp/MIL connector), MIL connector to 40-Pin
terminal UB-10-IO32D spring clamp terminal block, use for AS332T-A, AS332P-A, AS324MT-
module A, AS32AM10N-A, AS32AN02T-A
16 relay outputs, 20-Pin MIL connector, NPN, use for AS332T-A,
UB-10-OR16A
AS32AN02T-A and AS64AN02T-A
UB-10-OR16B 16 relay outputs, 20-Pin MIL connector, PNP, use for AS332P-A
32 transistor outputs, 40-Pin MIL connector, NPN, use for
UB-10-OT32A
AS32AN02T-A and AS64AN02T-A
UC-CMC003-01A
CANopen communication cable, use for AS-FCOPM series
(0.3M)
UC-CMC005-01A CANopen communication cable, use for AS-FCOPM series
(0.5M)
(1M)
(1.5M)
(2M)
(3M)
Network cables
(5M)
(10M)
(20M)
UC-EMC003-02A Ethernet communication cable, use for AS Series CPU modules, AS-
(0.3M) FEN02 and AS-FPFN02 function cards.
(0.5M) FEN02 and AS-FPFN02 function cards.
(1M) FEN02 and AS-FPFN02 function cards.
1-8

UC-EMC020-02A
(2M)
Ethernet communication cable, use for AS Series CPU modules, AS-
FEN02 and AS-FPFN02 function cards.
1_
1-9
1.2 Software
_1 1.2.1 Program Editor
The section describes the program editor ISPSoft.
 There are four types of programming languages: structure text (ST), ladder diagram (LD), sequential function chart
(SFC), and continuous function chart (CFC).
NOTE: CFC programming is only available in ISPSoft version 3.01 or higher.
1-10
 User-defined variables allow you to define a variable to replace a PLC device name. This enhances the readability of
1_
the program, and saves time when addressing the device.
 The Program Organization Unit (POU) framework divides the main program into several program units, and also
replaces the traditional subroutines with functions and function blocks. The makes the framework of the program
modular and easier to manage.
 Tasks manage the execution order of the programs. Tasks help you manage large-scale program development.
1 - 11
1.2.2 Program Organization Units and Tasks

_1 The Program Organization Units (POUs) are the basic elements that constitute the PLC program. Unlike the traditional
PLC program, the program framework introduced by IEC 61131-3 allows you to divide a large program into several small
units. These small units are called POUs. The POUs can be classified into three types.
1. Program (PROG): The program POU is the main program in the PLC. You can define the execution of this POU t
to be cyclic scan or interrupt driven, and arrange the scan order in the task list for program POUs.
2. Function block (FB): The function block (FB) POU is similar to a subroutine. The instructions in the function block
are executed after a program POU calls the function block with the related parameters.
3. Function (FC): The function (FC) POU in similar to a macro instruction. That is, you can write many operation
instructions or functions into a function-type POU, and then use then in a program POU or a function block POU.
Tasks are functions that control the order of program execution or according to certain interrupt conditions. The task
provides each program POU with a specific execution task, and specifies the execution order for the program POUs or
the way to enable them.
Normally, only some of the program POUs in a project take part in the actual execution. The task controls whether to
execute the program POU or not, and how to execute it. If the POU of the program type is not assigned in the task, the
program POU is saved as ordinary source code with the project instead of being compiled into the execution code for the
PLC. In addition, only the program POU needs to be assigned to the task. Function block POUs or function POUs are
automatically called by the program POU. There are three types of tasks.
1. Cyclic task: The program POUs assigned to cyclic tasks are scanned cyclically, and executed in order.
2. Timed interrupt task: If the interrupt time is reached, all program POUs assigned to the timed interrupt task are
executed in order.
3. Conditional interrupt task: Conditional Interrupts can be divided into several types, such as external interrupts, and
I/O interrupts. You must make sure that the PLC supports the interrupts before you use conditional interrupts in a
project. If you assign a program POU to a conditional interrupt task, the program POU is similar to an interrupt
subroutine. When the interrupt condition is satisfied (for example, the contact of the external interrupt is triggered)
then all program POUs assigned to the conditional interrupt task are executed in order.
1-12
2
Chapter 2 Devices
Table of Contents
2.1 Introduction to Devices ......................................................................... 2-2
2.1.1 Device Table ................................................................................. 2-2
2.1.2 Basic Structure of I/O Storage ......................................................... 2-3
2.1.3 Relation Between the PLC Action and the Device Type ........................ 2-3
2.1.4 Latched Areas in the Device Range .................................................. 2-4
2.2. Device Functions .................................................................................. 2-5

2.2.1 Values and Constants ..................................................................... 2-5
2.2.2 Floating-point Numbers .................................................................. 2-7
2.2.2.1 Single-precision Floating-point Numbers .......................................... 2-7
2.2.2.2 Decimal Floating-point Numbers ..................................................... 2-8
2.2.3 Strings ......................................................................................... 2-8
2.2.4 Input Relays (X) ............................................................................ 2-9
2.2.5 Output Relays (Y) .........................................................................2-10
2.2.6 Auxiliary Relays (M) ......................................................................2-10
2.2.7 Special Auxiliary Relays (SM) .........................................................2-11
2.2.8 Refresh Time for Special Auxiliary Relays .........................................2-62
2.2.9 Stepping Relays (S) ......................................................................2-70
2.2.10 Timers (T) ...................................................................................2-70
2.2.11 Counters ......................................................................................2-72
2.2.12 32-bit Counters (HC) .....................................................................2-73
2.2.13 Data Registers (D) ........................................................................2-75
2.2.14 Special Data Registers (SR) ...........................................................2-76
2.2.15 Special Data Registers Refresh Conditions...................................... 2-115
Registers………………………………………………………………………………………………..2-118
2.2.17 Index Register (E) ...................................................................... 2-144
2.2.18 File Registers (FR) ...................................................................... 2-144
2-1
2.1 Introduction to Devices

This section describes the values and strings processed by the PLC. It also describes the functions of devices, including
input, output and auxiliary relays, as well as timers, counters, and data registers. The PLC simulates external devices in
the PLC’s internal memory, so the word “device” is a generic name that refers to all the internal memory locations in the
PLC. A device can be a bit device or a word device. Bit devices simulate coils, contacts and flags, while word devices
simulate registers.
_2 2.1.1 Device Table

Type Device name Number of devices Range
Input relay X 1024 X0.0–X63.15
Output relay Y 1024 Y0.0–Y63.15
D 48,0000 D0.0–D29999.15
Data register
W 48,0000 W0.0–W29999.15 *4
Bit device Auxiliary relay M 8192 M0–M8191

Special auxiliary relay SM 2048 SM0–SM4095
Stepping relay S 2048 S0–S2047
Timer T 512 T0–T511
Counter C 512 C0–C511
32-bit counter HC 256 HC0–HC255
Input relay X 64 X0–X63
Output relay Y 64 Y0–Y63
D 30000 D0–D29999
Data register
W 30000 W0–W29999 *4
Special auxiliary relay SR 2048 SR0–SR2047

Word device
File register FR 65536 FR0–FR65535
Timer T 512 T0–T511

Counter C 512 C0–C511
32-bit counter HC 256(512 words) HC0–HC255
10 E0–E9
Index register E
5 E10–E14 *4
16 bits: -32768 to 32767

Constant*1 Decimal system K
32 bits: -2147483648 to 2147483647
16 bits: 16#0–16#FFFF
Hexadecimal system 16#
32 bits: 16#0–16#FFFFFFFF
Constant*2
Single-precision floating-
F 32 bits: ±1.17549435-38 to ±3.40282347+ 38
point number
String*3 String “$” 1–31 characters
*1: Constants are indicated by K in the device lists in Chapter 5 and Chapter 6 in the AS Series Programming Manual.
For example, when “K50” appears in the AS programming manual, enter only the number 50 in ISPSoft.
*2: Floating-point numbers are indicated by F/DF in the device lists in Chapter 5 and Chapter 6 in the AS Series
Programming Manual, but they are represented by decimal points in ISPSoft. For example, for the floating-point
number F500, enter 500.0 in ISPSoft.
2-2
C ha pt er 2 D e v ic es
*3: Strings are indicated by $ in Chapter 5 and Chapter 6 in the AS Series Programming Manual, but they are
represented by quotes (“ ”) in ISPSoft. For example, for the string of 1234, enter “1234” in ISPSoft.
*4: Used for editing in ISPSoft only.
2.1.2 Basic Structure of I/O Storage

Access by Access by Modify by 2_
Device Function Force the bit ON/OFF
bits words ISPSoft
X Input relay OK OK OK OK
Y Output relay OK OK OK OK
M Auxiliary relay OK - OK -
Special auxiliary
SM OK - OK -
relay
S stepping relay OK - OK -
T Timer OK OK OK -
C Counter OK OK OK -
HC 32-bit counter OK OK OK -
D Data register OK OK OK OK
SR Special data register - OK OK -
FR File register - OK*1 - -
E Index register - OK OK -
*1: Use an instruction for writing to an FR.
2.1.3 Relation Between the PLC Action and the Device Type
Device type Non-latched area Latched area
Other Other
Device Y File register
PLC action devices devices
Power: OFF→ON Cleared Cleared Retained Retained
Restore to defaults Cleared Cleared Cleared Cleared
STOP The non-latched area is cleared. Cleared Cleared Retained Retained
↓ The state of the non-latched area is
Retained Retained Retained Retained
RUN*1 retained.
SM203 is OFF.
The state of
(The state of
device Y is Cleared Retained Retained Retained
other devices
cleared.
are retained.)
SM203 is OFF.
The state of
(The state of
device Y is Retained Retained Retained Retained
other devices
RUN retained.
are retained.)
↓
SM203 is ON. *3
STOP*1 The state of
(The state of
device Y is Cleared Cleared Retained Retained
other devices
cleared.
are cleared.)
SM203 is ON.
The state of
(The state of
device Y is Retained Cleared Retained Retained
other devices
retained.
are cleared.)
SM204 is ON.*2 Cleared Cleared Retained Retained
2-3
Device type Non-latched area Latched area

Other Other
Device Y File register
PLC action devices devices
(All non-latched areas are cleared.)
SM205 is ON.*2
Retained Retained Retained Cleared
(All latched areas are cleared.)
_2 *1: For more on setting the states, see HWCONFIG in ISPSoft. The default for PLC STOP->RUN is “clear not-latched
area”. The default for PLC RUN->STOP is “clear the state of device Y”.
*2: PLC clears the areas when SM switches from OFF to ON. After clearing the areas, PLC switches the SM back to
OFF.
*3: When SM203 is ON, it clears the non-latched area once when PLC RUN->STOP. This function should work with AS
PLC CPU with FW V1.08.30 or later.
2.1.4 Latched Areas in the Device Range

Device Function Device range Latched area
X Input relay X0–X63 All devices are non-latched.
Y Output relay Y0–Y63 All devices are non-latched.
M*1 Auxiliary relay M0–M8191 The default range is M6000–M8191.
Some devices are latched, and cannot be

SM Special auxiliary relay SM0–SM2047 changed. Refer to the list of special auxiliary
relays for more information.
S*1 Stepping relay S0–S1023 The default range is S512–S1023
T Timer T0–T511 All devices are non-latched.
C*1 Counter C0–C511 The default range is C448–C511
HC*1 32-bit counter HC0–HC255 The default range is HC128–HC255
D0–D29999 The default range is D20000–D23999

D*1 Data register
W0–W29999 *2
FR File register FR0–FR65535 All devices are latched.
Some are latched, and cannot be changed.

SR Special data register SR0–SR2047 Refer to the list of special data registers for more
information.
E0–E9 All devices are non-latched.

E Index register
E10–E14 *2
*1: For more information on setting the latched area, see HWCONFIG in ISPSoft. Setting the latched area means the
other areas are seen as non-latched areas. The range of latched areas cannot exceed the device range. For example,
setting M600–M7000 as latched areas makes M0–M5999 and M7001–M8191 non-latched areas.
*2: Used for editing in ISPSoft only.
2-4
2.2. Device Functions

The following flow chart shows the procedure for processing a program in the PLC.
 Regenerating the input signal

1. Before the program is executed, the state of the
Input ter minal X external input signal is read into the memory location
Regener ating the input signal for the input signal. 2_
2. When program is executed, the state in the memory
Device memory
location for the input signal does not change even if
Device memory
the input signal changes from ON to OFF or from OFF

Proc es s in g th e prog ram to ON. The input signal is not refreshed until the next
scan begins.
Device memory
 Processing the program
After the input signal is refreshed, the instructions in the
program are executed in order from the start address of
Regener ating the output s ignal the program. The results are stored in the device memory.
and sending it to the output ter minal
 Regenerating the state of the output
After the instruction END is executed, the state in the
device memory is sent to the specified output terminal.
2.2.1 Values and Constants

Name Description
Bit A bit is the basic unit in the binary system. Its state is either 1 or 0.
A nibble is composed of four consecutive bits (for example b3–b0). Nibbles
Nibble
can represent 0–9 in the decimal system, or 0–F in the hexadecimal system.
A byte is composed of two consecutive nibbles ( 8 bits, b7–b0). Bytes can

Byte
represent 00–FF in the hexadecimal system.
A word is composed of two consecutive bytes (16 bits, b15–b0). Words can
Word
represent 0000–FFFF in the hexadecimal system.
A double word is composed of two consecutive words (i.e. 32 bits, b31–b0).

Double word
Double words represent 00000000–FFFFFFFF in the hexadecimal system.
The relation among bits, nibbles, bytes, words, and double words in the binary system is shown in the picture below.
DW D ouble w ord
W1 W0
W ord
BY3 BY2 BY1 BY0 B yt e
N B7 N B6 N B5 N B4 N B3 N B2 N B1 N B0
N ib ble
b31 b30 b29 b28 b27 b26 b25 b24b23 b22 b21 b20 b19 b18 b17 b16 b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 B it
2-5
The PLC uses four types of values to execute the operation according to different control purposes.
1. Binary number (BIN)
The PLC uses the binary system to operate on the values.
2. Decimal number (DEC)
The PLC uses decimal numbers for:

_2
 The setting value of a timer (T) or the setting value of a counter (C/HC); for example, TMR C0 50 (constant
K).
 The device number; for example, M10 and T30 (device number)
 The number before or after the decimal point; for example, X0.0, Y0.11, and D10.0 (device number).
 The constant K, used as the operand in an applied instruction. For example, MOV 123 D0 (constant K).
3. Binary-coded decimal (BCD)
A decimal value that is represented by a nibble or four bits so that sixteen consecutive bits represent a four-digit
decimal value.
4. Hexadecimal number (HEX)
The PLC uses hexadecimal numbers for:
 The constant 16#, used as the operand in an applied instruction; for example, MOV 16#1A2B D0
(hexadecimal constant).
The following table shows the corresponding values.
Binary Number Decimal Number Binary Code Decimal Hexadecimal Number

(BIN) (DEC) (BCD) (HEX)
Constant K, Constant 16#,

PLC internal execution BCD related instruction
Device number Device number
0000 0 0000 0
0001 1 0001 1
0010 2 0010 2
0011 3 0011 3
0100 4 0100 4
0101 5 0101 5
0110 6 0110 6
0111 7 0111 7
1000 8 1000 8
1001 9 1001 9
1010 10 - A
1011 11 - B
1100 12 - C
1101 13 - D
1110 14 - E
1111 15 - F
10000 16 0001 0000 10
10001 17 0001 0001 11
2-6
2.2.2 Floating-point Numbers

Floating-point numbers are represented by decimal points in ISPSoft. For example, the floating-point number 500 is
represented as 500.0.
2.2.2.1 Single-precision Floating-point Numbers
Floating-point numbers are represented by a 32-bit register. The representation adopts the IEEE754 standard, and the 2_
format shown in the following picture.
8 -b it 2 3- bi t
S E xpo ne nt Ma nti ssa
b 31 b0
S ig n b it
0 : Po siti ve
1 : Neg ati ve
Equation:
(− 1)S × 2 E − B × 1.M ; B = 127
The single-precision floating-point numbers range between ±2-126 to ±2+128, and correspond to the range between
±1.1755×10-38 to ±3.4028×10+38.
The AS Series PLC uses two consecutive registers for a 32-bit floating-point number. Take (D1, D0) for example.
D1 (b 15 ~b 0) D0 (b 15 ~b 0)
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
S E7 E6 E5 E1 E0 A22 A21 A20 A6 A5 A4 A3 A2 A1 A0
b31 b30 b29 b28 b24 b23 b22 b21 b20 b6 b5 b4 b3 b2 b1 b0
E xp on en t ( 8 b its ) Ma nt iss a (2 3b it s )
T he pos ition w here the d eci mal point is hid den
Ma nt iss a s ign b it (0 : Po s it iv e; 1: Ne ga tiv e)

W hen b 0~ b3 1 a re z eros , t he c on te nt is z ero .
Example 1:
23 is represented by a single-precision floating-point number.

Step 1: Convert 23 into the binary number, 23.0=10111.
Step 2: Normalize the binary number, 10111=1.0111 ×24 (0111 is the mantissa, and 4 is the exponent.).
Step 3: Get the value of the exponent.
∵ E-B=4→E-127=4 ∴ E=131=100000112
Step 4: Combine the sign bit, the exponent, and the mantissa to form the floating-point number.
0 10000011 011100000000000000000002=41B8000016
2-7
Example 2:
-23 is represented by a single-precision floating-point number.
Converting -23.0 into the floating-point number uses the same steps as converting 23.0 into the floating-point number,
except that the sign bit is 1.
1 10000011 011100000000000000000002=C1B8000016
_2 2.2.2.2 Decimal Floating-point Numbers
 Single-precision floating-point numbers and double-precision floating-point numbers can be converted into decimal
floating-point numbers so people can read them. However, internally the PLC uses single-precision floating-point
numbers and double-precision floating-point numbers.
 A 32-bit decimal floating-point number is represented by two consecutive registers. The constant is stored in the
first register whose number is smaller while the exponent is stored in the register whose number is bigger. Take
(D1, D0) for example.
[Ex ponent D1]
D eci mal f lo ati ng -po in t nu mb er=[C on sta nt D 0 ]* 1 0
Base number D0=±1,000 to ±9,999
Exponent D1=-41 to +35
The base number 100 does not exist in D0 because 100 is represented by 1,000×10-1. 32-bit decimal floating-point
numbers range between ±1175×10-41 to ±402×10+35.
2.2.3 Strings
The PLC can process strings composed of ASCII codes (*1). A complete string begins with a start character, and ends with
an ending character (NULL code). Strings can have maximum length of 31 characters, and ISPSoft automatically adds the
ending character (16#00).
1. No string (NULL code) is moved.
D0=0 (NULL)
2. The string has an even number of characters.
D0 16#62 (b) 16#61 (a)
D1 16#64 (d) 16#63 (b)
D2 0 (NULL)
2-8
3. The string has an odd number of characters.
D0 16#62 (b) 16#61 (a) 2_

D1 16#64 (d) 16#63 (b)
D2 0 (NULL) 16#65 (e)
*1: ASCII code chart
Hex 0 1 2 3 4 5 6 7 8 9 A B C D E F
ASCII                
Hex 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F
ASCII                
Hex 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F
ASCII SP ! " # $ % & ( ) * + ， - . /
Hex 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
ASCII 0 1 2 3 4 5 6 7 8 9 ： ; < = > ?
Hex 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F
ASCII @ A B C D E F G H I J K L M N O
Hex 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F
ASCII P Q R S T U V W X Y Z     
Hex 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F
ASCII ` a b c d e f g h i j k l M n o
Hex 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F
ASCII p q r s t u v w x y z { | } – 
Note:  represents an invisible character. Do not use it in strings.
2.2.4 Input Relays (X)

 Input function
The input is connected to the input device (external devices such as button switches, rotary switches, and number
switches), and the PLC reads the input signal. You can use input contact A or contact B several times in the
program, and the ON/OFF state of the input varies with the ON/OFF state of the input device.
 Input number (the decimal number)
For the PLC, the input numbers start from X0.0. The number of inputs varies with the number of inputs on the digital
input/output modules. The inputs are numbered according to the order in which the digital input/output modules are
connected to the CPU module. The maximum number of inputs for the PLC is 8192, and the input number range is
between X0.0 to X511.15.
2-9
 Input type
Inputs are classified into two types.
1. Regenerated inputs: The PLC reads the state of a regenerated input before the program is executed; for
example, LD X0.0.
2. Direct input: The state of a direct input is read by the PLC during the execution of the instructions; for example,
_2 LD DX0.0.
2.2.5 Output Relays (Y)

 Output function
The output sends the ON/OFF signal to drive the load connected to the output, such as an external signal lamp, a
digital display, or an electromagnetic valve. There are four types of outputs. They are relays, transistors (NPN and
PNP), and TRIACs (thyristors). You can use the output contact A or contact B several times in the program. Use output
Y only once in the program; otherwise, according the PLC’s program-scanning function, the state of the output depends
on the circuit connected to the last output Y in the program.
 Output number (the decimal number)

For the PLC, the output numbers start from Y0.0. The number of outputs varies with the number of outputs on the
digital input/output modules. The outputs are numbered according to the order in which the digital input/output modules
are connected to the PLC. The maximum number of outputs on the PLC is 1024, and the range is between Y0.0 and
Y63.15.
An output that is not used as an output device can be used as a general device.
 Output types
Outputs are classified into two types.
1. Regenerated output: The state of a regenerated output is not written until the program executes the END instruction,
according to the states of the outputs; for example, OUT Y0.0.
2. Direct output: The state of a direct output is written by the PLC during the execution of the instructions, according
to the states of the outputs; for example, OUT DY0.0.
2.2.6 Auxiliary Relays (M)

The auxiliary relay has contact A and contact B. It can be used several times in the program. You can combine the
control loops by using the auxiliary relay, but you cannot drive the external load using the auxiliary relay. You can use the
auxiliary relays in either of the following two ways.
1. For general use: In general use, if an electric power failure occurs when the PLC is running, the
auxiliary relay resets to the OFF state. When the power is restored, the auxiliary
relay remains in the OFF state.
2. For latched use: In latched use, ff an electric power failure occurs when the PLC is running, the state
of the auxiliary relay is retained. When the power is restored, the relay state
remains the same as before the power failure.
2-10
2.2.7 Special Auxiliary Relays (SM)

Every special auxiliary relay has its specific function. Do not use the special auxiliary relays which are not defined.
The special auxiliary relays and their functions are listed as follows. As to the SM numbers marked “*”, users can refer to
the additional remarks on special auxiliary relays/special data registers. “R” in the attribute column indicates that the
special auxiliary relay can read the data, whereas “R/W” in the attribute column indicates that it can read and write the
data. In addition, the mark “–” indicates that the status of the special auxiliary relay does not make any change. The mark
“#” indicates that the system will be set according to the status of the PLC, and users can read the setting value and refer
2_
to the related manual for more information.
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
SM Function   
ON RUN STOP
Error: the operation or operand exceeds the

SM0 ○ ○ OFF OFF – N R OFF
allowed range
Error: the operation or operand exceeds the
allowed range is locked.
SM5 Instruction inspection error ○ ○ OFF OFF – N R OFF
SM6 Data lost in the latched area ○ ○ OFF – – N R/W OFF
SM7 Insufficient power supply (24 V) ○ ○ OFF – – N R OFF
*SM8 Watchdog timer error ○ ○ OFF – – N R OFF
SM9 System error ○ ○ OFF – – N R OFF
SM10 I/O bus error ○ ○ OFF – – N R OFF
*SM22 Clearing the error log ○ ○ OFF OFF OFF N R/W OFF
SM23 Clearing the download log ○ ○ OFF OFF OFF N R/W OFF
SM24 Clearing the state-changing log of the PLC ○ ○ OFF OFF OFF N R/W OFF
The online-editing processing flag is on when the
SM25 ○ ○ OFF – – N R OFF
online-editing mode starts.
The debugging mode processing flag is on when
the debugging mode starts.
SM27 AS-F2AD: flags for buildt-in AD errors ○ ○ OFF – – N R OFF
Error: the output point is the same as the output
SM28 ○ ○ OFF OFF OFF N R/W OFF
that the high speed instruction used
SM30 Error in the remote module ○ ○ OFF – – N R OFF
SM34 Incorrect password ○ ○ OFF – – N R/W OFF
Enable saving data to the memory card. When
*SM36 ○ ○ OFF – – N R/W OFF
ON, the PLC runs according to the value in SR36.
SM76 The data is sent through Function Card 1. ○ - OFF OFF – N R/W OFF
SM77 The data is sent through Function Card 2. ○ - OFF OFF – N R/W OFF
Waiting to receive the reply through Function Card
SM78 ○ - OFF OFF – N R OFF
1
Waiting to receive the reply through Function Card
SM79 ○ - OFF OFF – N R OFF
2
SM80 Reception through Function Card 1 is complete. ○ - OFF OFF – N R/W OFF
SM81 Reception through Function Card 2 is complete. ○ - OFF OFF – N R/W OFF
2 - 11
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Error during receiving data through Function Card

SM82 1 when using the MODRW instruction or the RS ○ - OFF OFF – N R OFF
instruction.
Error during receiving data through Function Card
SM83 2 when using the MODRW instruction or the RS ○ - OFF OFF – N R OFF
instruction.
No data received through Function Card 1 after a
SM84 ○ - OFF OFF – N R/W OFF
specified period of time.
No data received through Function Card 2 after a
SM85 ○ - OFF OFF – N R/W OFF
specified period of time.
Choice made by Function Card 1 between the 8-
bit processing mode and the 16-bit processing
SM86 mode ○ - OFF – – N R/W OFF
ON: 8-bit processing mode
OFF: 16-bit processing mode
Choice made by Function Card 2 between the 8-
bit processing mode and the 16-bit processing
SM87 mode ○ - OFF – – N R/W OFF
The communication protocol of Function Card 1
SM90 ○ - OFF – – N R/W OFF
changes
The communication protocol of Function Card 2
SM91 ○ - OFF – – N R/W OFF
changes
SM94 Change in the LED lighting control in COM1 ○ ○ – – – H R/W OFF
SM95 Change in the LED lighting control in COM2 ○ ○ – – – H R/W OFF
*SM96 Data is sent through COM1. ○ ○ OFF OFF – N R/W OFF
*SM97 Data is sent through COM2. ○ ○ OFF OFF – N R/W OFF
*SM98 Waiting to receive the reply through COM1 ○ ○ OFF OFF – N R OFF
*SM99 Waiting to receive the reply through COM2 ○ ○ OFF OFF – N R OFF
*SM100 Reception through COM1 is complete. ○ ○ OFF OFF – N R/W OFF
*SM101 Reception through COM2 is complete. ○ ○ OFF OFF – N R/W OFF
Error during receiving data through COM1 when
*SM102 using the MODRW instruction or the RS ○ ○ OFF OFF – N R/W OFF
instruction.
Error during receiving data through COM2 when
*SM103 using the MODRW instruction or the RS ○ ○ OFF OFF – N R/W OFF
instruction.
No data received through COM1 after a specified
*SM104 ○ ○ OFF OFF – N R/W OFF
period of time.
No data received through COM2 after a specified
period of time.
Choice made by COM1 between the 8-bit
*SM106 ○ ○ OFF – – N R/W OFF
processing mode and the 16-bit processing mode
2-12
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
ON: 8-bit processing mode 2_

Choice made by COM2 between the 8-bit
processing mode and the 16-bit processing mode
*SM107 ○ ○ OFF – – N R/W OFF
SM166 VR0 started (works with SR166) ○ ○ OFF – – N R/W OFF
SM167 VR1 started (works with SR167) ○ ○ OFF – – N R/W OFF
SM168 The connection for Function Card 1 established. ○ - – – – N R OFF
SM169 Function Card 1 is in operation. ○ - OFF – – N R OFF
SM170 The connection for Function Card 2 established. ○ - – – – N R OFF
SM171 Function Card 12 is in operation. ○ - OFF – – N R OFF
When PLC RUN->STOP, it clears the non-latched
*SM203 ○ ○ OFF – – N R/W OFF
area once.
*SM204 All non-latched areas are cleared. ○ ○ OFF OFF OFF N R/W OFF
*SM205 All latched areas are cleared. ○ ○ OFF OFF OFF N R/W OFF
SM206 All output is inhibited ○ ○ OFF – – N R/W OFF
*SM209 The communication protocol of COM1 changes ○ ○ OFF OFF OFF N R/W OFF
Choice made by COM1 between the ASCII mode
and the RTU mode
*SM210 ○ ○ – – – H R/W OFF
ON: RTU mode
OFF: ASCII mode
*SM211 The communication protocol of COM1 changes ○ ○ OFF OFF OFF N R/W OFF
Choice made by COM2 between the ASCII mode
and the RTU mode
*SM212 ○ ○ – – – H R/W OFF
ON: RTU mode
OFF: ASCII mode
SM215 Running state of the PLC ○ ○ OFF ON OFF N R/W OFF
SM218 Error: real-time clock malfunction ○ ○ – – – N R OFF
SM219 Error: battery power for the real-time clock is low ○ ○ – – – N R OFF
*SM220 Calibrating the real-time clock within ±30 seconds ○ ○ OFF OFF – N R/W OFF
SM221 Enable daylight saving time (D.S.T.) ○ ○ – – – H R OFF
When selecting “Manual + Flags” in “I/O allocation
setting when Power On”, use this flag to activate
*SM230 ○ ○ – – – Y R/W OFF
the 1st module on the right-side of the CPU
module.
*SM231 ○ ○ – – – Y R/W OFF
the 2nd module on the right-side of the CPU
module.
*SM232 setting when Power On”, use this flag to activate ○ ○ – – – Y R/W OFF
the 3rd module on the right-side of the CPU
2-13
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 module.
*SM233 ○ ○ – – – Y R/W OFF
the 4th module on the right-side of the CPU
module.
*SM234 ○ ○ – – – Y R/W OFF
module.
*SM235 ○ ○ – – – Y R/W OFF
module.
*SM236 ○ ○ – – – Y R/W OFF
module.
*SM237 ○ ○ – – – Y R/W OFF
module.
*SM238 ○ ○ – – – Y R/W OFF
module.
*SM239 ○ ○ – – – Y R/W OFF
module.
*SM240 ○ ○ – – – Y R/W OFF
module.
*SM241 ○ ○ – – – Y R/W OFF
module.
*SM242 ○ ○ – – – Y R/W OFF
module.
*SM243 ○ ○ – – – Y R/W OFF
module.
2-14
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
module. 2_
*SM245 ○ ○ – – – Y R/W OFF
module.
*SM246 ○ ○ – – – Y R/W OFF
module.
*SM247 ○ ○ – – – Y R/W OFF
module.
*SM248 ○ ○ – – – Y R/W OFF
module.
*SM249 ○ ○ – – – Y R/W OFF
module.
*SM250 ○ ○ – – – Y R/W OFF
module.
*SM251 ○ ○ – – – Y R/W OFF
module.
*SM252 ○ ○ – – – Y R/W OFF
the 23rd module on the right-side of the CPU
module.
*SM253 ○ ○ – – – Y R/W OFF
module.
*SM254 ○ ○ – – – Y R/W OFF
module.
*SM255 ○ ○ – – – Y R/W OFF
module.
2-15
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 module.
*SM257 ○ ○ – – – Y R/W OFF
module.
*SM258 ○ ○ – – – Y R/W OFF
module.
*SM259 ○ ○ – – – Y R/W OFF
module.
*SM260 ○ ○ – – – Y R/W OFF
module.
*SM261 ○ ○ – – – Y R/W OFF
module.
Reversing the input direction for MPG 1 flag
SM270 ○ ○ OFF OFF – N R/W OFF
(X0.0/X0.1)
(X0.2/X0.3)
(X0.4/X0.5)
(X0.6/X0.7)
(X0.8/X0.9)
(X0.10/X0.11)
Reversing the input direction for high-speed
counter 1 flag
counter 2 flag
counter 3 flag
counter 4 flag
counter 5 flag
counter 6 flag
SM287 Reversing the input direction for high-speed ○ ○ OFF OFF – N R/W OFF
2-16
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
counter 7 flag 2_
counter 8 flag
Clearing the input point for high-speed counter 1
flag
flag
flag
flag
flag
flag
Setting counting mode for HC200.
HC200 counts down when SM300 is ON.
SM314 Setting counting mode for HC214. ○ ○ OFF – – N R OFF
2-17
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 HC214 counts down when SM314 is ON.

2-18
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SM344
○ ○ OFF OFF – N R/W OFF
2_
*SM400 The flag is always ON when the CPU runs. ○ ○ OFF ON OFF N R OFF
*SM401 The flag is always OFF when the CPU runs. ○ ○ OFF OFF ON N R OFF
*SM402 The flag is ON only at the first scan. ○ ○ OFF ON OFF N R OFF
*SM403 The flag is OFF only at the first scan. ○ ○ OFF OFF ON N R OFF
10 millisecond clock pulse during which the pulse
*SM404 is ON for 5 milliseconds and then OFF for 5 ○ ○ OFF – – N R OFF
milliseconds
100 millisecond clock pulse during which the pulse
*SM405 is ON for 50 milliseconds and then OFF for 50 ○ ○ OFF – – N R OFF
milliseconds
200 millisecond clock pulse during which the
*SM406 pulse is ON for 100 milliseconds and then OFF for ○ ○ OFF – – N R OFF
100 milliseconds
One second clock pulse during which the pulse is
*SM407 ON for 500 milliseconds and then OFF for 500 ○ ○ OFF – – N R OFF
milliseconds
Memory card is present
*SM450 ON: the memory card is present. ○ ○ – – – N R OFF
OFF: the memory card is not present.
The data in the memory card is being accessed.
ON: the data in the memory card is being
*SM452 accessed. ○ ○ OFF – – N R OFF
OFF: the data in the memory card is not
accessed.
2-19
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Error during the operation of the memory card.

*SM453 ON: an error occurs. ○ ○ OFF – – N R OFF
OFF: no error.
Enabling/disabling the data logger.
SM454 ON: enable ○ ○ OFF – – N R/W OFF
OFF: disable
The data logger is currently taking samples.
SM455 ON: number of records has reached its sampling ○ ○ OFF – – N R OFF
limit
Execution of data logger and the memory card.
*SM456 ○ ○ OFF – – N R/W OFF
ON: execution by the values in SR902.
State of the sample parameters in data logger
SM457 ○ ○ – – – N R OFF
ON: the sample parameter is set.
SM460 Outputting Y0.0/axis 1 (Y0.0/Y0.1). ○ ○ OFF OFF – N R OFF
SM461 Y0.0/axis 1 (Y0.0/Y0.1) output is complete. ○ ○ OFF OFF – N R/W OFF
SM462 Reversing the output direction of axis 1 (Y0.1) ○ ○ OFF OFF – N R/W OFF
*SM463 Stopping the output of Y0.0/axis 1 (Y0.0/Y0.1) ○ ○ OFF OFF – N R/W OFF
Enabling the hardware positive limit on axis 1
SM464 ○ ○ – – – Y R/W OFF
(Y0.0/Y0.1)
Alarm: exceeding the positive limit on axis 1
(Y0.0/Y0.1)
Enabling the hardware negative limit on axis 1
SM466 ○ ○ – – – Y R/W OFF
(Y0.0/Y0.1)
Alarm: exceeding the negative limit on axis 1
(Y0.0/Y0.1)
Enabling the S curve ramp-up/down on axis 1
(Y0.0/Y0.1)
Enabling fixed slope ramp-up/down on axis 1
(Y0.0/Y0.1)
Auto-reset when Y0.0/axis 1 (Y0.0/Y0.1) output is
complete.
Executing an interrupt I500 when pulse output
ends on axis 1 (Y0.0/Y0.1)
SM472 Outputting Y0.1. ○ ○ OFF OFF – N R OFF
SM473 Y0.1 output is complete. ○ ○ OFF OFF – N R/W OFF
*SM474 Stopping the output of Y0.1. ○ ○ OFF OFF – N R/W OFF
SM475 Auto-reset when Y0.1 output is complete. ○ ○ OFF OFF – N R/W OFF
Output immediately stops when the instruction is
disabled or stops for Y0.0/axis 1 (Y0.0/Y0.1)
disabled or stops for Y0.1
Change the target positon while outputting
Y0.0/axis 1 (Y0.0/Y0.1)
2-20
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SM479 Change the target positon while outputting Y0.1 ○ ○ OFF OFF – N R/W OFF 2_
SM482 Reversing the output direction of axis 2 (Y0.3) ○ ○ OFF OFF – N R/W OFF
*SM483 Stopping the output of Y0.2/axis 2 (Y0.2/Y0.3) ○ ○ OFF OFF – N R/W OFF
SM484 ○ ○ – – – Y R/W OFF
(Y0.2/Y0.3)
(Y0.2/Y0.3)
SM486 ○ ○ – – – Y R/W OFF
(Y0.2/Y0.3)
(Y0.2/Y0.3)
(Y0.2/Y0.3).
(Y0.2/Y0.3).
complete.
ends on axis 2 (Y0.2/Y0.3).
The output immediately stops when the instruction
is disabled or stops for Y0.2/axis 2 (Y0.2/Y0.3).
is disabled or stops for Y0.3.
Y0.2/axis 2 (Y0.2/Y0.3)
SM499 Change the target positon while outputting Y0.3 ○ ○ OFF OFF – N R/W OFF
SM502 Reversing the output direction of axis 3 (Y0.5). ○ ○ OFF OFF – N R/W OFF
*SM503 Stopping the output of Y0.4/axis 3 (Y0.4/Y0.5). ○ ○ OFF OFF – N R/W OFF
SM504 ○ ○ – – – Y R/W OFF
(Y0.4/Y0.5)
(Y0.4/Y0.5)
SM506 ○ ○ – – – Y R/W OFF
(Y0.4/Y0.5)
2-21
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM507
○ ○ OFF OFF – N R/W OFF
(Y0.4/Y0.5)
(Y0.4/Y0.5)
(Y0.4/Y0.5)
complete.
ends for axis 3 (Y0.4/Y0.5).
disabled or stops on Y0.4/axis 3 (Y0.4/Y0.5).
disabled or stops on Y0.5.
Y0.4/axis 3 (Y0.4/Y0.5)
SM522 Reversing the output direction of axis 4 (Y0.7) . ○ ○ OFF OFF – N R/W OFF
SM524 ○ ○ – – – Y R/W OFF
(Y0.6/Y0.7).
(Y0.6/Y0.7).
SM526 ○ ○ – – – Y R/W OFF
(Y0.6/Y0.7).
(Y0.6/Y0.7).
(Y0.6/Y0.7).
(Y0.6/Y0.7).
complete.
2-22
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM534 Stopping the output of Y0.7. ○ ○ OFF OFF – N R/W OFF 2_

disabled or stops for Y0.6/axis 4 (Y0.6/Y0.7).
disabled or stops for Y0.7.
Y0.6/axis 4 (Y0.6/Y0.7)
SM542 Reversing the output direction of axis 5 (Y0.9). ○ ○ OFF OFF – N R/W OFF
SM544 ○ ○ – – – Y R/W OFF
(Y0.8/Y0.9).
(Y0.8/Y0.9).
SM546 ○ ○ – – – Y R/W OFF
(Y0.8/Y0.9).
(Y0.8/Y0.9).
(Y0.8/Y0.9).
(Y0.8/Y0.9).
Auto-reset when Y0.8/axis 5 (Y0.8/Y0.9output is
complete.
is disabled or stops for Y0.9.
Y0.8/axis 5 (Y0.8/Y0.9)
2-23
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM562 Reversing the output direction of axis 6 (Y0.11). ○ ○ OFF OFF – N R/W OFF
SM564 ○ ○ – – – Y R/W OFF
(Y0.10/Y0.11).
(Y0.10/Y0.11).
SM566 ○ ○ – – – Y R/W OFF
(Y0.10/Y0.11).
(Y0.10/Y0.11).
(Y0.10/Y0.11).
(Y0.10/Y0.11).
Auto-reset when Y0.10/axis 6 (Y0.10/Y0.11)
output is complete.
*SM574 Stopping Y0.11 output. ○ ○ OFF OFF – N R/W OFF
disabled or stops for Y0.11.
Y0.10/axis 6 (Y0.10/Y0.11)
All outputs immediately stop when the instruction
is disabled or stops.
When the single-axis parameter is modified in the
position planning table, its
acceleration/deceleration time in SR should also
be synchronized.
Used to calculate the interval frequency of
acceleration and deceleration (for axis 1-6)
When TPO instruction uses position planning
table to control the output, if the output is stopped
*SM587 during execution, the axis should refer to its ○ ○ OFF OFF – N R/W OFF
relevant flags (e.g. SM476, SM496--SM576) for
the action to stop.
SM600 Zero flag ○ ○ OFF – – N R OFF
2-24
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SM601 Borrow flag ○ ○ OFF – – N R OFF 2_

SM602 Carry flag ○ ○ OFF – – N R OFF
Setting the working mode of the SORT instruction.
SM604 ON: descending order ○ ○ OFF – – N R/W OFF
OFF: ascending order
Designating the working mode of the SMOV
SM605 ○ ○ OFF – – N R/W OFF
instruction.
8-bit or 16-bit working mode.
SM606 ON: 8-bit ○ ○ OFF – – N R/W OFF
OFF: 16-bit
Matrix comparison flag.
SM607 ON: Comparing equivalent values. ○ ○ OFF – – N R/W OFF
OFF: Comparing different values.
Matrix comparison complete. When the last bits
are compared, SM608 is ON.
When SM609 is ON, the comparison starts from
bit 0.
Matrix bit search flag. When the matrix search
SM610 finds the matching bits or completes the search, ○ ○ OFF – – N R OFF
the search stops immediately and SM610 is ON.
Matrix pointer error flag. When the value of the
SM611 pointer exceeds the comparison range, SM611 is ○ ○ OFF – – N R OFF
ON.
Matrix pointer increasing flag. The current value of
the pointer increases by one.
Matrix pointer clearing flag. The current value of
the pointer is cleared to zero.
SM614 Carry flag for the matrix rotation/shift/output. ○ ○ OFF – – N R OFF
SM615 Borrow flag for the matrix shift/output. ○ ○ OFF – – N R/W OFF
Direction flag for the matrix rotation/shift.
SM616 OFF: the bits are shifted leftward. ○ ○ OFF – – N R/W OFF
ON: The bits are shifted rightward.
SM617 The bits with the value 0 or 1 are counted. ○ ○ OFF – – N R/W OFF
SM618 ON when the matrix counting result is 0. ○ ○ OFF – – N R/W OFF
SM619 ON when the instruction EI is executed. ○ ○ OFF OFF – N R OFF
When the results from the comparison using the
SM620 instruction CMPT# are that all devices are ON, ○ ○ OFF – – N R OFF
SM620 is ON.
Setting counting mode for HC.
2-25
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM624
○ ○ OFF – – N R/W OFF
SM645 Setting counting mode for HC24. ○ ○ OFF – – N R/W OFF
2-26
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
HC24 counts down when SM645 is ON. 2_

2-27
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM667
○ ○ OFF – – N R/W OFF
The DSCLP instruction uses floating-point
operations.
SM686 RAMP instruction mode ○ ○ OFF – – N R/W OFF
SM687 RAMP instruction execution is complete. ○ ○ OFF – – N R/W OFF
SM688 INCD instruction execution is complete. ○ ○ OFF – – N R/W OFF
SM690 String control mode. ○ ○ OFF – – N R/W OFF
SM691 HKY instruction input mode is 16-bit. ○ ○ OFF – – N R/W OFF
2-28
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
ON: the input is the hexadecimal input OFF: A–F 2_

are function keys.
After the execution of the HKY instruction is
complete, SM692 is ON for a scan cycle.
After the execution of the SEGL instruction is
After the execution of the DSW instruction is
Radian/degree flag.
SM695 ON: degrees ○ ○ OFF – – N R/W OFF
OFF: Radians
Error occurs in the initialization of the data
exchange through COM1.
Data exchange through COM1 enabled by
*SM750 ○ ○ OFF – – H R/W OFF
ISPSoft.
Connection 1 for data exchange through COM1
*SM752 ○ ○ OFF – – H R/W OFF
started
*SM753 ○ ○ OFF – – H R/W OFF
started
*SM754 ○ ○ OFF – – H R/W OFF
started
*SM755 ○ ○ OFF – – H R/W OFF
started
*SM756 ○ ○ OFF – – H R/W OFF
started
*SM757 ○ ○ OFF – – H R/W OFF
started
*SM758 ○ ○ OFF – – H R/W OFF
started
*SM759 ○ ○ OFF – – H R/W OFF
started
*SM760 ○ ○ OFF – – H R/W OFF
started
*SM761 ○ ○ OFF – – H R/W OFF
started
*SM762 ○ ○ OFF – – H R/W OFF
started
*SM763 ○ ○ OFF – – H R/W OFF
started
*SM764 ○ ○ OFF – – H R/W OFF
started
*SM765 ○ ○ OFF – – H R/W OFF
started
*SM766 ○ ○ OFF – – H R/W OFF
started
2-29
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM767
○ ○ OFF – – H R/W OFF
started
*SM768 ○ ○ OFF – – H R/W OFF
started
*SM769 ○ ○ OFF – – H R/W OFF
started
*SM770 ○ ○ OFF – – H R/W OFF
started
*SM771 ○ ○ OFF – – H R/W OFF
started
*SM772 ○ ○ OFF – – H R/W OFF
started
*SM773 ○ ○ OFF – – H R/W OFF
started
*SM774 ○ ○ OFF – – H R/W OFF
started
*SM775 ○ ○ OFF – – H R/W OFF
started
*SM776 ○ ○ OFF – – H R/W OFF
started
*SM777 ○ ○ OFF – – H R/W OFF
started
*SM778 ○ ○ OFF – – H R/W OFF
started
*SM779 ○ ○ OFF – – H R/W OFF
started
*SM780 ○ ○ OFF – – H R/W OFF
started
*SM781 ○ ○ OFF – – H R/W OFF
started
*SM782 ○ ○ OFF – – H R/W OFF
started
*SM783 ○ ○ OFF – – H R/W OFF
started
Successful data exchange connection 1 through
*SM784 ○ ○ OFF – – N R OFF
COM1
*SM785 ○ ○ OFF – – N R OFF
COM1
*SM786 ○ ○ OFF – – N R OFF
COM1
*SM787 ○ ○ OFF – – N R OFF
COM1
*SM788 ○ ○ OFF – – N R OFF
COM1
*SM789 ○ ○ OFF – – N R OFF
COM1
2-30
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM790
○ ○ OFF – – N R OFF
2_
COM1
*SM791 ○ ○ OFF – – N R OFF
COM1
*SM792 ○ ○ OFF – – N R OFF
COM1
*SM793 ○ ○ OFF – – N R OFF
COM1
*SM794 ○ ○ OFF – – N R OFF
COM1
*SM795 ○ ○ OFF – – N R OFF
COM1
*SM796 ○ ○ OFF – – N R OFF
COM1
*SM797 ○ ○ OFF – – N R OFF
COM1
*SM798 ○ ○ OFF – – N R OFF
COM1
*SM799 ○ ○ OFF – – N R OFF
COM1
*SM800 ○ ○ OFF – – N R OFF
COM1
*SM801 ○ ○ OFF – – N R OFF
COM1
*SM802 ○ ○ OFF – – N R OFF
COM1
*SM803 ○ ○ OFF – – N R OFF
COM1
*SM804 ○ ○ OFF – – N R OFF
COM1
*SM805 ○ ○ OFF – – N R OFF
COM1
*SM806 ○ ○ OFF – – N R OFF
COM1
*SM807 ○ ○ OFF – – N R OFF
COM1
*SM808 ○ ○ OFF – – N R OFF
COM1
*SM809 ○ ○ OFF – – N R OFF
COM1
*SM810 ○ ○ OFF – – N R OFF
COM1
*SM811 ○ ○ OFF – – N R OFF
COM1
*SM812 ○ ○ OFF – – N R OFF
COM1
2-31
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM813
COM1
*SM814 ○ ○ OFF – – N R OFF
COM1
*SM815 ○ ○ OFF – – N R OFF
COM1
Error in data exchange connection 1 through
*SM816 ○ ○ OFF – – N R OFF
COM1
*SM817 ○ ○ OFF – – N R OFF
COM1
*SM818 ○ ○ OFF – – N R OFF
COM1
*SM819 ○ ○ OFF – – N R OFF
COM1
*SM820 ○ ○ OFF – – N R OFF
COM1
*SM821 ○ ○ OFF – – N R OFF
COM1
*SM822 ○ ○ OFF – – N R OFF
COM1
*SM823 ○ ○ OFF – – N R OFF
COM1
*SM824 ○ ○ OFF – – N R OFF
COM1
*SM825 ○ ○ OFF – – N R OFF
COM1
*SM826 ○ ○ OFF – – N R OFF
COM1
*SM827 ○ ○ OFF – – N R OFF
COM1
*SM828 ○ ○ OFF – – N R OFF
COM1
*SM829 ○ ○ OFF – – N R OFF
COM1
*SM830 ○ ○ OFF – – N R OFF
COM1
*SM831 ○ ○ OFF – – N R OFF
COM1
*SM832 ○ ○ OFF – – N R OFF
COM1
*SM833 ○ ○ OFF – – N R OFF
COM1
*SM834 ○ ○ OFF – – N R OFF
COM1
*SM835 ○ ○ OFF – – N R OFF
COM1
2-32
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM836
2_
COM1
*SM837 ○ ○ OFF – – N R OFF
COM1
*SM838 ○ ○ OFF – – N R OFF
COM1
*SM839 ○ ○ OFF – – N R OFF
COM1
*SM840 ○ ○ OFF – – N R OFF
COM1
*SM841 ○ ○ OFF – – N R OFF
COM1
*SM842 ○ ○ OFF – – N R OFF
COM1
*SM843 ○ ○ OFF – – N R OFF
COM1
*SM844 ○ ○ OFF – – N R OFF
COM1
*SM845 ○ ○ OFF – – N R OFF
COM1
*SM846 ○ ○ OFF – – N R OFF
COM1
*SM847 ○ ○ OFF – – N R OFF
COM1
Error in the initialization of the data exchange
through COM2.
Data exchange through COM2 enabled by
*SM862 ○ ○ OFF – OFF H R/W OFF
ISPSoft.
*SM864 ○ ○ OFF – – H R/W OFF
started
*SM865 ○ ○ OFF – – H R/W OFF
started
*SM866 ○ ○ OFF – – H R/W OFF
started
*SM867 ○ ○ OFF – – H R/W OFF
started
*SM868 ○ ○ OFF – – H R/W OFF
started
*SM869 ○ ○ OFF – – H R/W OFF
started
*SM870 ○ ○ OFF – – H R/W OFF
started
*SM871 ○ ○ OFF – – H R/W OFF
started
*SM872 ○ ○ OFF – – H R/W OFF
started
2-33
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM873
started
*SM874 ○ ○ OFF – – H R/W OFF
started
*SM875 ○ ○ OFF – – H R/W OFF
started
*SM876 ○ ○ OFF – – H R/W OFF
started
*SM877 ○ ○ OFF – – H R/W OFF
started
*SM878 ○ ○ OFF – – H R/W OFF
started
*SM879 ○ ○ OFF – – H R/W OFF
started
*SM880 ○ ○ OFF – – H R/W OFF
started
*SM881 ○ ○ OFF – – H R/W OFF
started
*SM882 ○ ○ OFF – – H R/W OFF
started
*SM883 ○ ○ OFF – – H R/W OFF
started
*SM884 ○ ○ OFF – – H R/W OFF
started
*SM885 ○ ○ OFF – – H R/W OFF
started
*SM886 ○ ○ OFF – – H R/W OFF
started
*SM887 ○ ○ OFF – – H R/W OFF
started
*SM888 ○ ○ OFF – – H R/W OFF
started
*SM889 ○ ○ OFF – – H R/W OFF
started
*SM890 ○ ○ OFF – – H R/W OFF
started
*SM891 ○ ○ OFF – – H R/W OFF
started
*SM892 ○ ○ OFF – – H R/W OFF
started
*SM893 ○ ○ OFF – – H R/W OFF
started
*SM894 ○ ○ OFF – – H R/W OFF
started
*SM895 ○ ○ OFF – – H R/W OFF
started
2-34
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM896
2_
COM2
*SM897 ○ ○ OFF – – N R OFF
COM2
*SM898 ○ ○ OFF – – N R OFF
COM2
*SM899 ○ ○ OFF – – N R OFF
COM2
*SM900 ○ ○ OFF – – N R OFF
COM2
*SM901 ○ ○ OFF – – N R OFF
COM2
*SM902 ○ ○ OFF – – N R OFF
COM2
*SM903 ○ ○ OFF – – N R OFF
COM2
*SM904 ○ ○ OFF – – N R OFF
COM2
*SM905 ○ ○ OFF – – N R OFF
COM2
*SM906 ○ ○ OFF – – N R OFF
COM2
*SM907 ○ ○ OFF – – N R OFF
COM2
*SM908 ○ ○ OFF – – N R OFF
COM2
*SM909 ○ ○ OFF – – N R OFF
COM2
*SM910 ○ ○ OFF – – N R OFF
COM2
*SM911 ○ ○ OFF – – N R OFF
COM2
*SM912 ○ ○ OFF – – N R OFF
COM2
*SM913 ○ ○ OFF – – N R OFF
COM2
*SM914 ○ ○ OFF – – N R OFF
COM2
*SM915 ○ ○ OFF – – N R OFF
COM2
*SM916 ○ ○ OFF – – N R OFF
COM2
*SM917 ○ ○ OFF – – N R OFF
COM2
*SM918 ○ ○ OFF – – N R OFF
COM2
2-35
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM919
COM2
*SM920 ○ ○ OFF – – N R OFF
COM2
*SM921 ○ ○ OFF – – N R OFF
COM2
*SM922 ○ ○ OFF – – N R OFF
COM2
*SM923 ○ ○ OFF – – N R OFF
COM2
*SM924 ○ ○ OFF – – N R OFF
COM2
*SM925 ○ ○ OFF – – N R OFF
COM2
*SM926 ○ ○ OFF – – N R OFF
COM2
*SM927 ○ ○ OFF – – N R OFF
COM2
*SM928 ○ ○ OFF – – N R OFF
COM2
*SM929 ○ ○ OFF – – N R OFF
COM2
*SM930 ○ ○ OFF – – N R OFF
COM2
*SM931 ○ ○ OFF – – N R OFF
COM2
*SM932 ○ ○ OFF – – N R OFF
COM2
*SM933 ○ ○ OFF – – N R OFF
COM2
*SM934 ○ ○ OFF – – N R OFF
COM2
*SM935 ○ ○ OFF – – N R OFF
COM2
*SM936 ○ ○ OFF – – N R OFF
COM2
*SM937 ○ ○ OFF – – N R OFF
COM2
*SM938 ○ ○ OFF – – N R OFF
COM2
*SM939 ○ ○ OFF – – N R OFF
COM2
*SM940 ○ ○ OFF – – N R OFF
COM2
*SM941 ○ ○ OFF – – N R OFF
COM2
2-36
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM942
2_
COM2
*SM943 ○ ○ OFF – – N R OFF
COM2
*SM944 ○ ○ OFF – – N R OFF
COM2
*SM945 ○ ○ OFF – – N R OFF
COM2
*SM946 ○ ○ OFF – – N R OFF
COM2
*SM947 ○ ○ OFF – – N R OFF
COM2
*SM948 ○ ○ OFF – – N R OFF
COM2
*SM949 ○ ○ OFF – – N R OFF
COM2
*SM950 ○ ○ OFF – – N R OFF
COM2
*SM951 ○ ○ OFF – – N R OFF
COM2
*SM952 ○ ○ OFF – – N R OFF
COM2
*SM953 ○ ○ OFF – – N R OFF
COM2
*SM954 ○ ○ OFF – – N R OFF
COM2
*SM955 ○ ○ OFF – – N R OFF
COM2
*SM956 ○ ○ OFF – – N R OFF
COM2
*SM957 ○ ○ OFF – – N R OFF
COM2
*SM958 ○ ○ OFF – – N R OFF
COM2
*SM959 ○ ○ OFF – – N R OFF
COM2
AS remote module #1 connection status
SM976 (ON: connected; OFF: disconnected or not ○ ○ OFF – – N R OFF
connected)
SM977 AS remote module #2 connection status ○ ○ OFF – – N R OFF
2-37
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM983 AS remote module #8 connection status ○ ○ OFF – – N R OFF

Ethernet setting flag; ON: the data in SR1000–
SM1000 ○ ○ OFF – – N R/W OFF
SR1006 is written into the flash memory.
SM1001 State of the Ethernet connectivity ○ ○ OFF – – N R OFF
Data exchange through AS-FEN02 enabled by
*SM1006 ○ – OFF – – N R/W OFF
ISPSoft.
Connection 1 for data exchange through AS-
*SM1008 ○ – OFF – – N R/W OFF
FEN02 started
*SM1009 ○ – OFF – – N R/W OFF
FEN02 started
*SM1010 ○ – OFF – – N R/W OFF
FEN02 started
*SM1011 ○ – OFF – – N R/W OFF
FEN02 started
*SM1012 ○ – OFF – – N R/W OFF
FEN02 started
*SM1013 ○ – OFF – – N R/W OFF
FEN02 started
*SM1014 ○ – OFF – – N R/W OFF
FEN02 started
*SM1015 ○ – OFF – – N R/W OFF
FEN02 started
*SM1016 ○ – OFF – – N R OFF
AS-FEN02
*SM1017 ○ – OFF – – N R OFF
AS-FEN02
*SM1018 ○ – OFF – – N R OFF
AS-FEN02
*SM1019 ○ – OFF – – N R OFF
AS-FEN02
*SM1020 ○ – OFF – – N R OFF
AS-FEN02
*SM1021 ○ – OFF – – N R OFF
AS-FEN02
*SM1022 ○ – OFF – – N R OFF
AS-FEN02
*SM1023 Successful data exchange connection 8 through ○ – OFF – – N R OFF
2-38
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
AS-FEN02 2_
Error in data exchange connection 1 through AS-
*SM1024 ○ – OFF – – N R OFF
FEN02
*SM1025 ○ – OFF – – N R OFF
FEN02
*SM1026 ○ – OFF – – N R OFF
FEN02
*SM1027 ○ – OFF – – N R OFF
FEN02
*SM1028 ○ – OFF – – N R OFF
FEN02
*SM1029 ○ – OFF – – N R OFF
FEN02
*SM1030 ○ – OFF – – N R OFF
FEN02
*SM1031 ○ – OFF – – N R OFF
FEN02
*SM1090 TCP connection busy. ○ ○ OFF – – N R OFF
*SM1091 UDP connection busy. ○ ○ OFF – – N R OFF
SM1100 Ethernet connection error ○ ○ OFF – – N R OFF
*SM1106 Basic Ethernet management: connection error ○ ○ OFF – – N R OFF
*SM1107 Basic Ethernet management: Basic setting error ○ ○ OFF – – N R OFF
Basic TCP/UDP socket management: the local
*SM1109 ○ ○ OFF – – N R OFF
port is already used.
SM1111 EtherNet/IP data exchange flag ○ ○ OFF – – N R OFF
*SM1113 Email service error ○ ○ OFF – – N R OFF
*SM1116 Trigger 1 switch for the email. ○ ○ OFF – – N R OFF
*SM1117 Trigger 1 for the email ○ ○ OFF – – N R OFF
ON: Trigger 1 is triggered and the email has been
*SM1119 ○ ○ OFF – – N R OFF
sent successfully.
ON: Trigger 1 is triggered but the email cannot be
*SM1120 ○ ○ OFF – – N R OFF
sent due to email content error.
ON: Trigger 1 is triggered and there is an SMTP
*SM1122 ○ ○ OFF – – N R OFF
server response timeout.
*SM1123 ○ ○ OFF – – N R OFF
server response error.
ON: Trigger 1 is triggered and the size of the
*SM1124 ○ ○ OFF – – N R OFF
attachment exceeds the limit.
Trigger 1 is triggered and the attachment is not
*SM1125 ○ ○ OFF – – N R OFF
found.
*SM1129 ○ ○ OFF – – N R OFF
sent successfully.
2-39
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM1130
*SM1132 ○ ○ OFF – – N R OFF
*SM1133 ○ ○ OFF – – N R OFF
*SM1134 ○ ○ OFF – – N R OFF
ON: Trigger 2 is triggered and the attachment is
*SM1135 ○ ○ OFF – – N R OFF
not found.
*SM1139 ○ ○ OFF – – N R OFF
sent successfully.
*SM1140 ○ ○ OFF – – N R OFF
*SM1142 ○ ○ OFF – – N R OFF
*SM1143 ○ ○ OFF – – N R OFF
*SM1144 ○ ○ OFF – – N R OFF
*SM1145 ○ ○ OFF – – N R OFF
not found.
*SM1149 ○ ○ OFF – – N R OFF
sent successfully.
*SM1150 ○ ○ OFF – – N R OFF
*SM1152 ○ ○ OFF – – N R OFF
*SM1153 ○ ○ OFF – – N R OFF
*SM1154 ○ ○ OFF – – N R OFF
*SM1155 ○ ○ OFF – – N R OFF
not found.
*SM1166 Error in data exchange through Ethernet ○ ○ – – – N R OFF
*SM1167 Data exchange through Ethernet started ○ ○ OFF – – H R/W OFF
Connection 1 for data exchange through Ethernet
*SM1168 ○ ○ OFF – – H R/W OFF
started
*SM1169 ○ ○ OFF – – H R/W OFF
started
2-40
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM1170
2_
started
*SM1171 ○ ○ OFF – – H R/W OFF
started
*SM1172 ○ ○ OFF – – H R/W OFF
started
*SM1173 ○ ○ OFF – – H R/W OFF
started
*SM1174 ○ ○ OFF – – H R/W OFF
started
*SM1175 ○ ○ OFF – – H R/W OFF
started
*SM1176 ○ ○ OFF – – H R/W OFF
started
*SM1177 ○ ○ OFF – – H R/W OFF
started
*SM1178 ○ ○ OFF – – H R/W OFF
started
*SM1179 ○ ○ OFF – – H R/W OFF
started
*SM1180 ○ ○ OFF – – H R/W OFF
started
*SM1181 ○ ○ OFF – – H R/W OFF
started
*SM1182 ○ ○ OFF – – H R/W OFF
started
*SM1183 ○ ○ OFF – – H R/W OFF
started
*SM1184 ○ – OFF – – H R/W OFF
started
*SM1185 ○ – OFF – – H R/W OFF
started
*SM1186 ○ – OFF – – H R/W OFF
started
*SM1187 ○ – OFF – – H R/W OFF
started
*SM1188 ○ – OFF – – H R/W OFF
started
*SM1189 ○ – OFF – – H R/W OFF
started
*SM1190 ○ – OFF – – H R/W OFF
started
*SM1191 ○ – OFF – – H R/W OFF
started
*SM1192 ○ – OFF – – H R/W OFF
started
2-41
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM1193
○ – OFF – – H R/W OFF
started
*SM1194 ○ – OFF – – H R/W OFF
started
*SM1195 ○ – OFF – – H R/W OFF
started
*SM1196 ○ – OFF – – H R/W OFF
started
*SM1197 ○ – OFF – – H R/W OFF
started
*SM1198 ○ – OFF – – H R/W OFF
started
*SM1199 ○ – OFF – – H R/W OFF
started
*SM1200 ○ ○ OFF – – N R OFF
Ethernet
*SM1201 ○ ○ OFF – – N R OFF
Ethernet
*SM1202 ○ ○ OFF – – N R OFF
Ethernet
*SM1203 ○ ○ OFF – – N R OFF
Ethernet
*SM1204 ○ ○ OFF – – N R OFF
Ethernet
*SM1205 ○ ○ OFF – – N R OFF
Ethernet
*SM1206 ○ ○ OFF – – N R OFF
Ethernet
*SM1207 ○ ○ OFF – – N R OFF
Ethernet
*SM1208 ○ ○ OFF – – N R OFF
Ethernet
*SM1209 ○ ○ OFF – – N R OFF
Ethernet
*SM1210 ○ ○ OFF – – N R OFF
Ethernet
*SM1211 ○ ○ OFF – – N R OFF
Ethernet
*SM1212 ○ ○ OFF – – N R OFF
Ethernet
*SM1213 ○ ○ OFF – – N R OFF
Ethernet
*SM1214 ○ ○ OFF – – N R OFF
Ethernet
*SM1215 ○ ○ OFF – – N R OFF
Ethernet
2-42
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM1216
○ – OFF – – N R OFF
2_
Ethernet
*SM1217 ○ – OFF – – N R OFF
Ethernet
*SM1218 ○ – OFF – – N R OFF
Ethernet
*SM1219 ○ – OFF – – N R OFF
Ethernet
*SM1220 ○ – OFF – – N R OFF
Ethernet
*SM1221 ○ – OFF – – N R OFF
Ethernet
*SM1222 ○ – OFF – – N R OFF
Ethernet
*SM1223 ○ – OFF – – N R OFF
Ethernet
*SM1224 ○ – OFF – – N R OFF
Ethernet
*SM1225 ○ – OFF – – N R OFF
Ethernet
*SM1226 ○ – OFF – – N R OFF
Ethernet
*SM1227 ○ – OFF – – N R OFF
Ethernet
*SM1228 ○ – OFF – – N R OFF
Ethernet
*SM1229 ○ – OFF – – N R OFF
Ethernet
*SM1230 ○ – OFF – – N R OFF
Ethernet
*SM1231 ○ – OFF – – N R OFF
Ethernet
*SM1232 ○ ○ OFF – – N R OFF
Ethernet
*SM1233 ○ ○ OFF – – N R OFF
Ethernet
*SM1234 ○ ○ OFF – – N R OFF
Ethernet
*SM1235 ○ ○ OFF – – N R OFF
Ethernet
*SM1236 ○ ○ OFF – – N R OFF
Ethernet
*SM1237 ○ ○ OFF – – N R OFF
Ethernet
*SM1238 ○ ○ OFF – – N R OFF
Ethernet
2-43
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM1239
Ethernet
*SM1240 ○ ○ OFF – – N R OFF
Ethernet
*SM1241 ○ ○ OFF – – N R OFF
Ethernet
*SM1242 ○ ○ OFF – – N R OFF
Ethernet
*SM1243 ○ ○ OFF – – N R OFF
Ethernet
*SM1244 ○ ○ OFF – – N R OFF
Ethernet
*SM1245 ○ ○ OFF – – N R OFF
Ethernet
*SM1246 ○ ○ OFF – – N R OFF
Ethernet
*SM1247 ○ ○ OFF – – N R OFF
Ethernet
*SM1248 ○ – OFF – – N R OFF
Ethernet
*SM1249 ○ – OFF – – N R OFF
Ethernet
*SM1250 ○ – OFF – – N R OFF
Ethernet
*SM1251 ○ – OFF – – N R OFF
Ethernet
*SM1252 ○ – OFF – – N R OFF
Ethernet
*SM1253 ○ – OFF – – N R OFF
Ethernet
*SM1254 ○ – OFF – – N R OFF
Ethernet
*SM1255 ○ – OFF – – N R OFF
Ethernet
*SM1256 ○ – OFF – – N R OFF
Ethernet
*SM1257 ○ – OFF – – N R OFF
Ethernet
*SM1258 ○ – OFF – – N R OFF
Ethernet
*SM1259 ○ – OFF – – N R OFF
Ethernet
*SM1260 ○ – OFF – – N R OFF
Ethernet
*SM1261 ○ – OFF – – N R OFF
Ethernet
2-44
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SM1262
○ – OFF – – N R OFF
2_
Ethernet
*SM1263 ○ – OFF – – N R OFF
Ethernet
SM1269 Socket configuration error ○ ○ OFF – – N R/W OFF
SM1270 Successful TCP socket 1 connection ○ ○ OFF – – N R OFF
SM1271 TCP socket 1 data received ○ ○ OFF – – N R OFF
SM1272 TCP socket 1 data sent ○ ○ OFF – – N R OFF
SM1273 TCP socket 1 connection starting ○ ○ OFF – – N R OFF
SM1274 TCP socket 1 connection closing ○ ○ ON – – Y R ON
SM1275 TCP socket 1 data is being sent ○ ○ OFF – – N R OFF
SM1277 TCP socket 1─Error flag ○ ○ OFF – – N R OFF
SM1283 TCP socket 2 data is being sent ○ ○ OFF – – N R OFF
SM1291 TCP socket 3 data is being sent. ○ ○ OFF – – N R OFF
SM1299 TCP socket 4 data is being sent. ○ ○ OFF – – N R OFF
RTU-EN01 connection 1 status
SM1312 (ON: connected; OFF: disconnected or not ○ ○ OFF – – N R OFF
connected)
SM1313 RTU-EN01 connection 2 status ○ ○ OFF – – N R OFF
SM1334 UDP socket 1 connection started ○ ○ OFF – – N R OFF
SM1335 UDP socket 1 data receiving ○ ○ OFF – – N R OFF
2-45
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SM1336 UDP socket 1 data sending ○ ○ OFF – – N R OFF

SM1337 UDP socket 1 connection closed ○ ○ ON – – Y R ON
SM1338 UDP socket 1─Error flag ○ ○ OFF – – N R OFF
SM1341 UDP socket 2 data sending ○ ○ OFF – – N R OFF
Data exchange through EtherNet/IP (Scanner)
*SM1375 ○ ○ OFF – – H R/W OFF
started.
Connection 1 for data exchange through
*SM1376 ○ ○ OFF – – H R/W OFF
EtherNet/IP (Scanner) started
*SM1377 ○ ○ OFF – – H R/W OFF
*SM1378 ○ ○ OFF – – H R/W OFF
*SM1379 ○ ○ OFF – – H R/W OFF
*SM1380 ○ ○ OFF – – H R/W OFF
*SM1381 ○ ○ OFF – – H R/W OFF
*SM1382 ○ ○ OFF – – H R/W OFF
*SM1383 ○ ○ OFF – – H R/W OFF
*SM1384 ○ ○ OFF – – H R/W OFF
*SM1385 ○ ○ OFF – – H R/W OFF
*SM1386 ○ ○ OFF – – H R/W OFF
*SM1387 Connection 12 for data exchange through ○ ○ OFF – – H R/W OFF
2-46
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
EtherNet/IP (Scanner) started 2_

*SM1388 ○ ○ OFF – – H R/W OFF
*SM1389 ○ ○ OFF – – H R/W OFF
*SM1390 ○ ○ OFF – – H R/W OFF
*SM1391 ○ ○ OFF – – H R/W OFF
*SM1392 ○ – OFF – – H R/W OFF
*SM1393 ○ – OFF – – H R/W OFF
*SM1394 ○ – OFF – – H R/W OFF
*SM1395 ○ – OFF – – H R/W OFF
*SM1396 ○ – OFF – – H R/W OFF
*SM1397 ○ – OFF – – H R/W OFF
*SM1398 ○ – OFF – – H R/W OFF
*SM1399 ○ – OFF – – H R/W OFF
*SM1400 ○ – OFF – – H R/W OFF
*SM1401 ○ – OFF – – H R/W OFF
*SM1402 ○ – OFF – – H R/W OFF
*SM1403 ○ – OFF – – H R/W OFF
*SM1404 ○ – OFF – – H R/W OFF
*SM1405 ○ – OFF – – H R/W OFF
*SM1406 ○ – OFF – – H R/W OFF
*SM1407 ○ – OFF – – H R/W OFF
*SM1408 ○ ○ OFF – – N R OFF
EtherNet/IP (Scanner)
*SM1409 ○ ○ OFF – – N R OFF
*SM1410 Error in data exchange connection 3 through ○ ○ OFF – – N R OFF
2-47
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 EtherNet/IP (Scanner)
*SM1411 ○ ○ OFF – – N R OFF
*SM1412 ○ ○ OFF – – N R OFF
*SM1413 ○ ○ OFF – – N R OFF
*SM1414 ○ ○ OFF – – N R OFF
*SM1415 ○ ○ OFF – – N R OFF
*SM1416 ○ ○ OFF – – N R OFF
*SM1417 ○ ○ OFF – – N R OFF
*SM1418 ○ ○ OFF – – N R OFF
*SM1419 ○ ○ OFF – – N R OFF
*SM1420 ○ ○ OFF – – N R OFF
*SM1421 ○ ○ OFF – – N R OFF
*SM1422 ○ ○ OFF – – N R OFF
*SM1423 ○ ○ OFF – – N R OFF
*SM1424 ○ – OFF – – N R OFF
*SM1425 ○ – OFF – – N R OFF
*SM1426 ○ – OFF – – N R OFF
*SM1427 ○ – OFF – – N R OFF
*SM1428 ○ – OFF – – N R OFF
*SM1429 ○ – OFF – – N R OFF
*SM1430 ○ – OFF – – N R OFF
*SM1431 ○ – OFF – – N R OFF
*SM1432 ○ – OFF – – N R OFF
*SM1433 Error in data exchange connection 26 through ○ – OFF – – N R OFF
2-48
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
EtherNet/IP (Scanner) 2_
*SM1434 ○ – OFF – – N R OFF
*SM1435 ○ – OFF – – N R OFF
*SM1436 ○ – OFF – – N R OFF
*SM1437 ○ – OFF – – N R OFF
*SM1438 ○ – OFF – – N R OFF
*SM1439 ○ – OFF – – N R OFF
Error in I/O connection 1 through EtherNet/IP
*SM1440 ○ ○ OFF - - N R OFF
(Adapter)
*SM1441 ○ ○ OFF - - N R OFF
(Adapter)
*SM1442 ○ ○ OFF - - N R OFF
(Adapter)
*SM1443 ○ ○ OFF - - N R OFF
(Adapter)
*SM1444 ○ ○ OFF - - N R OFF
(Adapter)
*SM1445 ○ ○ OFF - - N R OFF
(Adapter)
*SM1446 ○ ○ OFF - - N R OFF
(Adapter)
*SM1447 ○ ○ OFF - - N R OFF
(Adapter)
I/O connection 1 is established through
*SM1448 ○ ○ OFF - - N R OFF
EtherNet/IP (Adapter)
*SM1449 ○ ○ OFF - - N R OFF
*SM1450 ○ ○ OFF - - N R OFF
*SM1451 ○ ○ OFF - - N R OFF
*SM1452 ○ ○ OFF - - N R OFF
*SM1453 ○ ○ OFF - - N R OFF
*SM1454 ○ ○ OFF - - N R OFF
2-49
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SM1455
○ ○ OFF - - N R OFF
Auto-reset the control over Delta servo axis 1 on
the CAN bus.
SM1582 the CAN bus. ○ ○ OFF OFF – N R/W OFF
Auto-reset the control over Delta inverter axis 21

on the CAN bus.
SM1602 on the CAN bus. ○ ○ OFF OFF – N R/W OFF
Heartbeat error of Delta inverter CAN
communication ID 21
communication ID 22
communication ID 23
communication ID 24
communication ID 25
communication ID 26
communication ID 27
communication ID 28
2-50
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SM1621
Delta inverter CAN communication ID 21 is
○ ○ OFF OFF – N R OFF
2_
starting
starting
starting
starting
starting
starting
starting
starting
SM1631 Positioning completed for Delta servo CAN axis 1 ○ ○ OFF OFF – N R/W OFF
SM1641 Communication stops for Delta servo CAN axis 1 ○ ○ OFF OFF – N R/W OFF
SM1651 Servo is ON for Delta servo CAN axis 1 ○ ○ OFF OFF – N R OFF
The function of going back and forth is enabled for
Delta servo CAN axis 1. See the DDRVAC
2-51
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 instruction (API 2804).

SM1662 Delta servo CAN axis 2. See the DDRVAC ○ ○ OFF OFF – N R/W OFF
instruction (API 2804).
instruction (API 2804)
The go-back/go-forth direction indication flag for
Delta servo CAN axis 1
Initialization and CAN communication (INITC and
CASD) completed for Delta servo
SM1682 The CAN communication error flag for Delta servo ○ ○ OFF OFF – N R OFF
Initialization and CAN communication completed
for Delta inverter
To set the Delta special CAN communication
SM1684 ON/OFF when a connection is lost ○ ○ OFF OFF – N R/W OFF
OFF: stops all the communications
2-52
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
ON: stops only the lost-connection one 2_

To read the self-defined Delta servo parameters
P0-12
OFF: initialize a consecutive number of modules
ON: initialize a specific module
SM1691 Heartbeat error of Delta special CAN axis 1 ○ ○ OFF OFF – N R OFF
＊SM1709 ○ – OFF – – N R/W OFF
through Function Card 1
Data exchange through Function Card 1 enabled
＊SM1710 ○ – OFF – OFF N R/W OFF
by ISPSoft
Connection 1 for data exchange through Function
＊SM1712 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1713 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1714 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1715 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1716 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1717 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1718 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1719 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1720 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1721 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1722 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1723 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1724 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1725 Connection 14 for data exchange through Function ○ – OFF – – N R/W OFF
2-53
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Card 1 started
＊SM1726 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1727 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1728 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1729 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1730 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1731 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1732 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1733 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1734 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1735 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1736 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1737 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1738 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1739 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1740 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1741 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1742 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1743 ○ – OFF – – N R/W OFF
Card 1 started
＊SM1744 ○ – OFF – – N R OFF
Function Card 1
＊SM1745 ○ – OFF – – N R OFF
Function Card 1
＊SM1746 ○ – OFF – – N R OFF
Function Card 1
＊SM1747 ○ – OFF – – N R OFF
Function Card 1
＊SM1748 Successful data exchange connection 5 through ○ – OFF – – N R OFF
2-54
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
Function Card 1 2_
＊SM1749 ○ – OFF – – N R OFF
Function Card 1
＊SM1750 ○ – OFF – – N R OFF
Function Card 1
＊SM1751 ○ – OFF – – N R OFF
Function Card 1
＊SM1752 ○ – OFF – – N R OFF
Function Card 1
＊SM1753 ○ – OFF – – N R OFF
Function Card 1
＊SM1754 ○ – OFF – – N R OFF
Function Card 1
＊SM1755 ○ – OFF – – N R OFF
Function Card 1
＊SM1756 ○ – OFF – – N R OFF
Function Card 1
＊SM1757 ○ – OFF – – N R OFF
Function Card 1
＊SM1758 ○ – OFF – – N R OFF
Function Card 1
＊SM1759 ○ – OFF – – N R OFF
Function Card 1
＊SM1760 ○ – OFF – – N R OFF
Function Card 1
＊SM1761 ○ – OFF – – N R OFF
Function Card 1
＊SM1762 ○ – OFF – – N R OFF
Function Card 1
＊SM1763 ○ – OFF – – N R OFF
Function Card 1
＊SM1764 ○ – OFF – – N R OFF
Function Card 1
＊SM1765 ○ – OFF – – N R OFF
Function Card 1
＊SM1766 ○ – OFF – – N R OFF
Function Card 1
＊SM1767 ○ – OFF – – N R OFF
Function Card 1
＊SM1768 ○ – OFF – – N R OFF
Function Card 1
＊SM1769 ○ – OFF – – N R OFF
Function Card 1
＊SM1770 ○ – OFF – – N R OFF
Function Card 1
2-55
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Function Card 1
＊SM1772 ○ – OFF – – N R OFF
Function Card 1
＊SM1773 ○ – OFF – – N R OFF
Function Card 1
＊SM1774 ○ – OFF – – N R OFF
Function Card 1
＊SM1775 ○ – OFF – – N R OFF
Function Card 1
＊SM1776 ○ – OFF – – N R OFF
Function Card 1
＊SM1777 ○ – OFF – – N R OFF
Function Card 1
＊SM1778 ○ – OFF – – N R OFF
Function Card 1
＊SM1779 ○ – OFF – – N R OFF
Function Card 1
＊SM1780 ○ – OFF – – N R OFF
Function Card 1
＊SM1781 ○ – OFF – – N R OFF
Function Card 1
＊SM1782 ○ – OFF – – N R OFF
Function Card 1
＊SM1783 ○ – OFF – – N R OFF
Function Card 1
＊SM1784 ○ – OFF – – N R OFF
Function Card 1
＊SM1785 ○ – OFF – – N R OFF
Function Card 1
＊SM1786 ○ – OFF – – N R OFF
Function Card 1
＊SM1787 ○ – OFF – – N R OFF
Function Card 1
＊SM1788 ○ – OFF – – N R OFF
Function Card 1
＊SM1789 ○ – OFF – – N R OFF
Function Card 1
＊SM1790 ○ – OFF – – N R OFF
Function Card 1
＊SM1791 ○ – OFF – – N R OFF
Function Card 1
＊SM1792 ○ – OFF – – N R OFF
Function Card 1
＊SM1793 ○ – OFF – – N R OFF
Function Card 1
＊SM1794 Error in data exchange connection 19 through ○ – OFF – – N R OFF
2-56
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
Function Card 1 2_
＊SM1795 ○ – OFF – – N R OFF
Function Card 1
＊SM1796 ○ – OFF – – N R OFF
Function Card 1
＊SM1797 ○ – OFF – – N R OFF
Function Card 1
＊SM1798 ○ – OFF – – N R OFF
Function Card 1
＊SM1799 ○ – OFF – – N R OFF
Function Card 1
＊SM1800 ○ – OFF – – N R OFF
Function Card 1
＊SM1801 ○ – OFF – – N R OFF
Function Card 1
＊SM1802 ○ – OFF – – N R OFF
Function Card 1
＊SM1803 ○ – OFF – – N R OFF
Function Card 1
＊SM1804 ○ – OFF – – N R OFF
Function Card 1
＊SM1805 ○ – OFF – – N R OFF
Function Card 1
＊SM1806 ○ – OFF – – N R OFF
Function Card 1
＊SM1807 ○ – OFF – – N R OFF
Function Card 1
＊SM1821 ○ – OFF – – N R/W OFF
through Function Card 2
Data exchange through Function Card 2 enabled
＊SM1822 ○ – OFF – OFF N R/W OFF
by ISPSoft
＊SM1824 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1825 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1826 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1827 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1828 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1829 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1830 ○ – OFF – – N R/W OFF
Card 2 started
2-57
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Card 2 started
＊SM1832 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1833 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1834 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1835 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1836 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1837 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1838 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1839 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1840 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1841 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1842 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1843 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1844 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1845 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1846 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1847 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1848 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1849 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1850 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1851 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1852 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1853 ○ – OFF – – N R/W OFF
Card 2 started
2-58
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
Card 2 started 2_
＊SM1855 ○ – OFF – – N R/W OFF
Card 2 started
＊SM1856 ○ – OFF – – N R OFF
Function Card 2
＊SM1857 ○ – OFF – – N R OFF
Function Card 2
＊SM1858 ○ – OFF – – N R OFF
Function Card 2
＊SM1859 ○ – OFF – – N R OFF
Function Card 2
＊SM1860 ○ – OFF – – N R OFF
Function Card 2
＊SM1861 ○ – OFF – – N R OFF
Function Card 2
＊SM1862 ○ – OFF – – N R OFF
Function Card 2
＊SM1863 ○ – OFF – – N R OFF
Function Card 2
＊SM1864 ○ – OFF – – N R OFF
Function Card 2
＊SM1865 ○ – OFF – – N R OFF
Function Card 2
＊SM1866 ○ – OFF – – N R OFF
Function Card 2
＊SM1867 ○ – OFF – – N R OFF
Function Card 2
＊SM1868 ○ – OFF – – N R OFF
Function Card 2
＊SM1869 ○ – OFF – – N R OFF
Function Card 2
＊SM1870 ○ – OFF – – N R OFF
Function Card 2
＊SM1871 ○ – OFF – – N R OFF
Function Card 2
＊SM1872 ○ – OFF – – N R OFF
Function Card 2
＊SM1873 ○ – OFF – – N R OFF
Function Card 2
＊SM1874 ○ – OFF – – N R OFF
Function Card 2
＊SM1875 ○ – OFF – – N R OFF
Function Card 2
＊SM1876 ○ – OFF – – N R OFF
Function Card 2
2-59
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 Function Card 2
＊SM1878 ○ – OFF – – N R OFF
Function Card 2
＊SM1879 ○ – OFF – – N R OFF
Function Card 2
＊SM1880 ○ – OFF – – N R OFF
Function Card 2
＊SM1881 ○ – OFF – – N R OFF
Function Card 2
＊SM1882 ○ – OFF – – N R OFF
Function Card 2
＊SM1883 ○ – OFF – – N R OFF
Function Card 2
＊SM1884 ○ – OFF – – N R OFF
Function Card 2
＊SM1885 ○ – OFF – – N R OFF
Function Card 2
＊SM1886 ○ – OFF – – N R OFF
Function Card 2
＊SM1887 ○ – OFF – – N R OFF
Function Card 2
＊SM1888 ○ – OFF – – N R OFF
Function Card 2
＊SM1889 ○ – OFF – – N R OFF
Function Card 2
＊SM1890 ○ – OFF – – N R OFF
Function Card 2
＊SM1891 ○ – OFF – – N R OFF
Function Card 2
＊SM1892 ○ – OFF – – N R OFF
Function Card 2
＊SM1893 ○ – OFF – – N R OFF
Function Card 2
＊SM1894 ○ – OFF – – N R OFF
Function Card 2
＊SM1895 ○ – OFF – – N R OFF
Function Card 2
＊SM1896 ○ – OFF – – N R OFF
Function Card 2
＊SM1897 ○ – OFF – – N R OFF
Function Card 2
＊SM1898 ○ – OFF – – N R OFF
Function Card 2
＊SM1899 ○ – OFF – – N R OFF
Function Card 2
＊SM1900 Error in data exchange connection 13 through ○ – OFF – – N R OFF
2-60
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
Function Card 2 2_
＊SM1901 ○ – OFF – – N R OFF
Function Card 2
＊SM1902 ○ – OFF – – N R OFF
Function Card 2
＊SM1903 ○ – OFF – – N R OFF
Function Card 2
＊SM1904 ○ – OFF – – N R OFF
Function Card 2
＊SM1905 ○ – OFF – – N R OFF
Function Card 2
＊SM1906 ○ – OFF – – N R OFF
Function Card 2
＊SM1907 ○ – OFF – – N R OFF
Function Card 2
＊SM1908 ○ – OFF – – N R OFF
Function Card 2
＊SM1909 ○ – OFF – – N R OFF
Function Card 2
＊SM1910 ○ – OFF – – N R OFF
Function Card 2
＊SM1911 ○ – OFF – – N R OFF
Function Card 2
＊SM1912 ○ – OFF – – N R OFF
Function Card 2
＊SM1913 ○ – OFF – – N R OFF
Function Card 2
＊SM1914 ○ – OFF – – N R OFF
Function Card 2
＊SM1915 ○ – OFF – – N R OFF
Function Card 2
＊SM1916 ○ – OFF – – N R OFF
Function Card 2
＊SM1917 ○ – OFF – – N R OFF
Function Card 2
＊SM1918 ○ – OFF – – N R OFF
Function Card 2
＊SM1919 ○ – OFF – – N R OFF
Function Card 2
*1: For items with a * mark, Refer to Section 2.2.1.6 for Additional Remarks on Special Auxiliary Relays and Special Data
Registers for details.
*2: The system executes according to the parameters set in HWCONFIG. When the SM power changes from OFF to
ON, the state is -, and the latched area is marked as N.
*3: The function card here means AS-F232, AS-F422 and AS-F485.
2-61
2.2.8 Refresh Time for Special Auxiliary Relays

Special auxiliary
Refresh time
relay
The system automatically sets the flag to ON and resets it to OFF.
SM0–SM1
ON: operation error.
SM5
_2 ON: an error occurs when the program is written in the PLC.
During power-on, the system checks whether the data in the latched area has been lost.
SM6
ON: data in the latched area has been lost. You reset it to OFF.
SM7 ON: power supply (24 V) is not sufficient. You reset it to OFF.
The system automatically sets SM8 to ON and resets it to OFF.
SM8
ON: there is a watchdog timer error.
SM9
ON: there is a system error.
SM10
ON: there is an I/O bus error.
You set the flag to ON, and the system automatically resets it to OFF.
SM22–SM24
ON: the log is cleared.
ON: users are editing with ISPSoft.
SM25–SM26
OFF: users have logged out of ISPSoft.
The system checks for anything wrong.
SM28
ON: something is wrong. You reset it to OFF.
SM30 ON: an error occurs in the remote module. The system resets it to OFF.
SM34 ON: the wrong password is entered. The system resets it to OFF.
ON: the system saves the data to the memory card. After saving is complete, the system resets it
SM36
to OFF automatically. You set it to ON to enable saving.
ON: the system executes the communication task. After the communication task is complete, the
SM76–SM77
system resets it to OFF automatically. You set it to ON to enable execution.
ON: communication is in progress. After the communication is complete, the system resets it to
SM78–SM79
OFF automatically.
SM80–SM81 ON: reception is complete. You reset it to OFF.
SM82–SM83 ON: an error occurs in the response. You reset it to OFF.
SM84–SM85 ON: a timeout occurs. You reset it to OFF.
You set the flag to ON and reset it to OFF.
SM86–SM87 ON: 8-bit mode
OFF: 16-bit mode
You set the flag to ON. After the communication protocol is changed, the system resets it to
SM90–SM91
OFF.
After power-on, the flag is ON or OFF according to the settings in HWCONFIG. You can change
SM94–SM95
this setting.
SM96–SM97 You set the flag to ON. After the data is sent, the system automatically resets the flag to OFF.
ON: communication is in process. After the communication is complete, the system resets it to
SM98–SM99
OFF automatically.
The system automatically sets the flag to ON, and you reset it to OFF.
SM100–SM101
ON: the command is received.
SM102–SM103
ON: the command received is wrong.
SM104–SM105
ON: there is a receive timeout.
2-62
Special auxiliary
Refresh time
relay
SM106–SM107 ON: 8-bit mode
OFF: 16-bit mode
SM166–SM167 You set the flag to ON and reset it to OFF.
2_
SM168–SM171 The system automatically sets the flag to ON, and resets it to OFF.
You set the flag to ON and after PLC RUN->STOP, it clears the non-latched area. The system
SM203
automatically resets the flag to OFF.
You set the flag to ON, and the system automatically resets it to OFF.
SM204–SM205
ON: clear the non-latched/latched areas.
You set SM206 to ON and reset it to OFF.
SM206
ON: inhibit all output.
You set SM209 to ON, and the system automatically resets it to OFF.
SM209
ON: the communication protocol of COM1 changes.
You set SM210 to ON and reset it to OFF for COM1.
SM210 ON: RTU mode
OFF: ASCII mode
You set SM211 to ON, and the system automatically resets it to OFF.
SM211
ON: the communication protocol of COM2 changes.
You set SM210 to ON and reset it to OFF for COM2.
SM212 ON: RTU mode
OFF: ASCII mode
SM215 ON: the PLC runs.
OFF: the PLC stops.
The system checks the real-time clock at power-on.
SM218 ON: real-time clock error
You reset it to OFF.
The system monitors the battery power of the real-time clock.
SM219 ON: real-time clock power is low
The system resets it to OFF.
SM220
ON: calibrating the real-time clock within ±30 seconds
The flag is refreshed according to the settings in HWCONFIG or when the DST instruction (API
SM221 1607) is executed.
ON: the DST instruction is executed.
SM230-SM261 The flag is refreshed according to the settings in HWCONFIG; you can redefine this setting.
The flag is ON when the CSFO instruction is executed.
SM270–SM275 ON: enable reversing the input direction
OFF: disable reversing the input direction
SM281–SM288 ON: counting down
OFF: counting up
SM291–SM296 ON: enable clearing the input points
OFF: disable clearing the input points
SM300 ON: counting down
OFF: counting up
2-63
Special auxiliary
Refresh time
relay
The system sets the flag to ON and reset it to OFF.
OFF: counting up
_2 OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
2-64
Special auxiliary
Refresh time
relay
OFF: counting up
OFF: counting up 2_
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
OFF: counting up
SM400–SM403
The flag is refreshed every scan cycle.
SM404
SM404 is refreshed every 5 milliseconds.
SM405
SM406
SM407
SM407 is refreshed every 0.5 seconds.
SM450
ON: memory card is inserted into the PLC.
2-65
Special auxiliary
Refresh time
relay
OFF: memory card is removed out of the PLC.
SM452–SM453 The system sets the flag to ON or OFF.
SM454 You set the flag to ON or OFF.
SM455 The system sets the flag to ON or OFF.
_2 SM456 You set the flag to ON to save. After the saving is complete, the system resets it to OFF.
SM461 The system sets the flag to ON and you reset it to OFF.
SM462–SM464 You set the flag to ON or OFF.
SM478–SM479 You set the flag to ON or OFF and the system sets the flag to OFF.
2-66
Special auxiliary
Refresh time
relay
2_
You set the flag to ON and the system resets it to OFF.
SM580
ON: disable high-speed output
SM585 You set the flag to ON or OFF and the system sets the flag to OFF.
SM586--SM587 You set the flag to ON or OFF.
SM600–SM602
The flag is refreshed when the instruction is executed.
SM604 ON: sort in descending order
OFF: sort in ascending order
SM605 You set SM605 to ON and reset it to OFF.
SM606 ON: 8-bit mode
OFF: 16-bit mode
SM608 The flag is refreshed when the instruction is executed.
SM610–SM611 The flag is refreshed when the instruction is executed.
2-67
Special auxiliary
Refresh time
relay
SM619 The flag is refreshed when the EI or DI instruction is executed.
SM620 The flag is refreshed when the CMPT instruction is executed.
_2 SM687 The flag is refreshed when the RAMP instruction is executed.

SM688 The flag is refreshed when the INCD instruction is executed.
SM692 The flag is refreshed when the HKY instruction is executed.
SM693 The flag is refreshed when the SEGL instruction is executed.
SM694 The flag is refreshed when the DSW instruction is executed.
SM749 The system is refreshed at power-on after the data exchange parameters are downloaded.
SM750–SM783 After the data exchange parameters are downloaded, you set the flag to ON or OFF.
SM784–SM847 The flag is ON when the system is refreshed.
SM861 The system is refreshed at power-on after the data exchange parameters are downloaded.
SM862–SM895 After the parameters of data exchange are downloaded, you set the flag to ON or OFF.
SM896–SM959 The flag is ON, when the system is refreshed automatically.
SM976-SM990 The flag is ON, when the system is refreshed automatically.
SM1000 You set the flag to ON and after saving, the system sets the flag to OFF.
ON: the Ethernet connection is active.
SM1001
OFF: the Ethernet connection is not active.
SM1006 After the parameters of data exchange are downloaded, you set the flag to ON or OFF.
SM1008—SM1015 After the parameters of data exchange are downloaded, you set the flag to ON or OFF.
SM1016—SM1031 The flag is ON, when the system is refreshed automatically.
SM1090 ON: the TCP connection is busy.
SM1091 ON: the UDP connection is busy.
SM1100 The flag is refreshed when API 2200-API 2210 is executed or the network cable is reconnected.
SM1106 ON: the PHY initialization fails.
SM1107 ON: the IP address, the netmask address, and the gateway address are set incorrectly.
SM1109 ON: the socket function is enabled and the same port is used.
SM1113 ON: there is a server error.
SM1116 ON: the trigger of the PLC parameter is enabled.
SM1117 ON: the trigger of the PLC parameter is triggered.
SM1119 ON: the trigger is enabled and the last mail has been sent successfully.
SM1120 ON: the trigger is enabled and the last mail has been sent with an error.
SM1122–SM1123 ON: the trigger is enabled and there is an SMTP server response timeout.
SM1124 ON: the trigger is enabled and the size of the attachment exceeds the limit.
SM1125 ON: the trigger is enabled and the attachment is not found.
SM1126–SM1127 ON: the trigger of the PLC parameter is enabled.
2-68
Special auxiliary
Refresh time
relay
SM1132 ON: the trigger is enabled and there is an SMTP server response timeout.
SM1133 ON: the trigger is enabled and there is an SMTP server response error.
SM1136 ON: the trigger for the PLC parameter is enabled. 2_
SM1137 ON: the trigger for the PLC parameter is triggered.
SM1146 ON: the trigger for the PLC parameter is enabled.
SM1147 ON: the trigger for the PLC parameter is triggered.
SM1166 After the data exchange parameters are downloaded, the system is refreshed.
SM1167–SM1199 After the data exchange parameters are downloaded, you set the flag to ON or OFF.
SM1200–SM1263 ON: when the system is refreshed.
SM1269 ON: there is a socket configuration error.
SM1270–SM1353 The flag is refreshed when the socket function is executed.
After the data exchange parameters are downloaded through EtherNet/IP, you set the flag to ON
SM1375–SM1407
or OFF.
SM1408–SM1439 ON: an error occurred in data exchange through EtherNet/IP.
SM1440–SM1447 ON: a timeout occurred in the adapter of the I/O connection through EtherNet/IP.
ON: I/O connection is established through EtherNet/IP (Adapter).
SM1448~SM1455 OFF: I/O connection is NOT established through EtherNet/IP (Adapter) or the communication is
disconnected.
SM1611-SM1618 The system sets the flag to ON or OFF.
SM1631–SM1638 The system sets the flag to ON and you set it to OFF.
SM1684—SM1685 You set the flag to ON or OFF.
2-69
Special auxiliary
Refresh time
relay
_2 SM1856–SM1919 The system sets the flag to ON or OFF.
2.2.9 Stepping Relays (S)

You can easily use the stepping relay in industrial automation to set a procedure. It is the most basic device in sequential
function chart (SFC) programming. Refer to the ISPSoft User Manual for more information on sequential function chart
programming.
There are 2048 stepping relays, (S0–S2047). Every stepping relay is like an output relay in that it has an output coil,
contact A, and contact B. You can use a stepping relay several times in a program, but the relay cannot directly drive the
external load. In addition, you can use the stepping relay as a general auxiliary relay when it is not used in a sequential
function chart.
2.2.10 Timers (T)

This topic describes the timers available in ISPSoft. Refer to the ISPSoft User Manual for more information on timers.
 100 millisecond timer: The timer specified by the TMR instruction takes 100 milliseconds as the timing unit.
 1 millisecond timer: The timer specified by the TMRH instruction takes 1 millisecond as the timing unit.
 The accumulative timers are ST0–ST511. If you want to use the device-monitoring function, these timers can
monitor T0–T511.
 If you use the same timer repeatedly in a program, including in different TMR and TMRH instructions, the timer
setting value is the one that the timer matches first.
 If you use the same timer repeatedly in a program, the timer is OFF when one of the conditional contacts is OFF.
 If you use the same timer in a program as the timer for a subroutine’s exclusive use and an accumulative timer in the
program, it is OFF when one of the conditional contacts is OFF.
 When the timer switches from ON to OFF and the conditional contact is ON, the timer is reset and counts again.
 When the TMR instruction is executed, the specified timer coil is ON and the timer begins to count. When the value
of the timer matches the timer setting value (value of the timer ≧ setting value), the state of the contact is ON.
A. General-purpose timers
When the TMR instruction is executed, the general-purpose timer begins to count. When the value of the timer
matches the timer setting value, the output coil is ON.
• When X0.0=ON and the timer takes 100 ms as the timing unit, the output coil T0 is ON when the value of the
timer = timer setting value100.
• When X0.0=OFF or the power is off, the value of the timer is 0 and the output coil T0 is OFF.
2-70
2_
10 sec
X0. 0
SV: K100
T0(PV)
Y0. 0
B. Accumulative timers
When the TMR instruction is executed, the accumulative timer begins to count. When the value of the timer matches
the timer setting value, the output coil is ON. As long as you add the letter S in front of the letter T, the timer
becomes an accumulative timer. When the conditional contact is OFF, the value of the accumulative timer is not
reset. When the conditional contact is ON, the accumulative timer counts from the current value.
• When X0.0=ON and the timer T250 takes 100 ms as the timing unit, the output coil T250 is ON when the
value of the timer = timer setting value 100.
• When X0.0=OFF or the power is off, the accumulative timer ST250 stops counting, and the value of the timer
stays the same. When X0.0=ON, the value of the timer is the accumulating value. When the accumulated
value = timer setting value 100, the output coil T250 is ON.
T1 T2 T1+T2=10 sec
X0. 0
SV: K100
T250(PV)
Y0. 0
2-71
C. Timers used in function blocks
T412–T511 are the timers that you can use in the function block or in interrupts.
When the TMR or END instruction is executed, the timer in the functional block begins to count. When the value of
the timer matches the timer setting value, the output coil is ON.
If you use a general-purpose timer in a function block or an interrupt, and the function or interrupt is not executed, the
_2 timer cannot count correctly.
2.2.11 Counters
 Characteristics of the 16-bit counter
Item 16-bit counter

Type General type
Number C0–C511
Direction Counting up
Setting value 0–32,767
The setting value can be either the constant or the value in the data
Specifying the counter setting value
register.
The counter stops counting when the value of the counter matches
Change of the current value
the counter setting value.
The contact is ON when the value of the counter matches the counter
Output contact
setting value.
When the instruction RST is executed, the current value is cleared to
Reset
zero, and the contact is reset of OFF.
Action of the contact After the scan is complete, the contact acts.
 Function of the counter
Each time the input switches from OFF to ON, the value of the counter is the same as the output coil. You can use
either the decimal constant or the value in the data register as the counter setting value.
16-bit counter:
1. Setting range: 0–32,767. The setting values 0 and 1 mean the same thing in that the output contact is ON when the
counter counts for the first time.
2. For the general-purpose counter, the current value of the counter is cleared when power is lost. If the counter is
latching, the current value of the counter and the state of the contact before power was lost power are retained. The
latched counter counts from the current value when the power supply is restored.
3. If you use the MOV instruction or ISPSoft to transmit a value larger than the counter setting value to the current
value register C0, the contact of the counter C0 is ON and the current value becomes the same as the counter
setting value the next time X0.1 switches from OFF to ON.
4. You can use either the constant or the value in the data register as the counter setting value.
5. The counter setting value can be positive or negative. If the counter counts up from 32,767, the next value is 0.
6. Use the counters here with CNT instruction. The example used here is a common one. Refer to API 1003 CNT
instruction for more advanced applicaiotns.
2-72
2_
1. When X0.0=ON, the RST instruction is executed, the current value of C0 is reset to zero, and the output contact of
the counter C0 is FF.
2. When X0.1 changes from OFF to ON, the value of the counter increments by one.
3. When the value of the counter C0 reaches the counter setting value of 5, the contact of the counter C0 is ON (the
current value of C0 = the counter setting value = 5). After that the trigger from X0.1 is not accepted by C0 and the
current value of C0 stays at the value 5.
X 0.0
X 0.1
5
4 (SV)
C0 ( PV ) 3
2
1
0 0
Y 0.0 ,C0
2.2.12 32-bit Counters (HC)

 Characteristics of the 32-bit counter
Item 32-bit counter

Type Up/down counter Up counter High-speed counter
Number HC0–HC63 HC64–HC199 HC200–HC255
Direction Counts up/down Counts up Counts up/down
Setting value -2,147,483,648 to +2,147,483,647
Specification of the The counter setting value can be either the constant or the value occupying two
counter setting value data registers (32-bit).
Change of the current The counter keeps counting even after the value of the counter matches the counter
value setting value.
Output contact The contact is ON when the value of the addition counter matches the counter
2-73
Item 32-bit counter

setting value.
The contact is reset to OFF when the value of the subtraction counter matches the
counter setting value.
When the RST instruction is executed, the current value is cleared to zero, and the
Reset
contact is reset to OFF.
Action of the contact After the DCNT instruction scan is complete, the contact acts.
_2
 32-bit general-purpose addition/subtraction counter
1. The difference between the 32-bit general-purpose addition counters and the 32-bit general-purpose subtraction
counters depends on the states of the special auxiliary relays SM621–SM684. For example, the counter HC0 is
an addition counter when SM621 is OFF, whereas HC0 is a subtraction counter when SM621 is ON.
2. You can use either the constant or the value in the data registers as the counter setting value, and this setting
value can be positive or negative. If you use the value in the data registers as the counter setting value, this
setting value occupies two consecutive registers.
3. For the general-purpose counter, the current value of the counter is cleared when power is lost. If the counter is
latching, the current value of the counter and the state of the contact before loss of power is retained. The
latched counter counts from the current value when power is restored.
4. If the counter counts up from 2,147,483,647, the next incremental value is -2,147,483,648. If the counter counts
down from -2,147,483,648, the next incremental value is 2,147,483,647.
5. Use the high-speed counters here with DCNT instruction. The example used here is a common one. Refer to
API 1004 DCNT instruction for more advanced applicaiotns.
 32-bit high speed addition/subtraction counter
Refer to the instruction description of API1004 DCNT in AS Series Programming Manual for more details.
Example:
2-74
1. X10.0 drives SM621 to determine the counting direction (up/down) for HC0.
2. When X11.0 changes from OFF to ON, the RST instruction is executed and the PV in HC0 is cleared to 0 and its
contact is OFF.
3. When X12.0 changes from OFF to ON, PV for HC0 will count up (plus 1) or count down (minus 1).
4. When PV in HC0 changes from -6 to -5, the contact HC0 changes from OFF to ON. When PV in HC0 changes from
-5 to -6, the contact HC0 changes from ON to OFF. 2_
Accu mul ati vel y Accu mul ati vel y

X10.0 i ncr ea sin g P rog re ssive ly i ncr ea sin g
d ecre asi ng
X11.0
X12.0
5
4 4
3 3
HC0 2 2
1 1
(PV )
0 0 0
-1
-2
-3 -3
-4 -4
-5 -5
-6 -6
Wh en t he o u tpu t c on tact w as O N -7 -7
-8
Y0.0,
HC0 Con tacts
2.2.13 Data Registers (D)

The data register stores 16-bit data. The highest bit represents either a positive sign or a negative sign, and the values
that the data registers can store range between -32,768 to +32,767.
Two 16-bit registers can be combined into a 32-bit register; for example, (D+1, D) in which the lower number register
represents the low 16 bits. The highest bit represents either a positive sign or a negative sign, and the values that the
data registers can store range between -2,147,483,648 to +2,147,483,647.
 Four 16-bit registers can be combined into a 64-bit register; for example, (D+3, D+2, D+1, D) in which the lower
number register represents the lower 16 bits. The highest bit represents either a positive sign or a negative sign,
and the values that the data registers can store range between -9,223,372,036,854,776 to
+9,223,372,036,854,775,807.
 You can also use the data registers to refresh the values in the control registers in the modules other than digital
I/O modules. Refer to the ISPSoft User Manual for more information on refreshing the values in the control
registers.
2-75
There are three types of registers.
 General-purpose registers: When the PLC changes to RUN, or is disconnected, the value in the register is cleared
to zero. If you want to retain the data when the PLC changes to RUN, Refer to the ISPSoft User Manual for more
information. Note that the value is still cleared to zero when the PLC is disconnected.
 Latched register: If the PLC is disconnected, the data in the latched register is not cleared. In other words, the
_2
value before the disconnection is retained. If you want to clear the data in the latched area, you can use the RST or
ZRST instructions.
 Frequently mapped registers: If the PLC program contains a module, after each scan cycle, the PLC performs data
mapping with the module. And the mapped data is stored between D26000~D29999. Refer to Chapter 8 of AS
Operation Manual for more details on the automatically assigned addresses of the devices. You can also check the
assigned addresses of the device while configuring in HWCONFIG of ISPSoft.
2.2.14 Special Data Registers (SR)

Every special data register has its own definition and specific function. System status and the error messages are stored
in the special data registers. You can also use special data registers to monitor the system statuses. The special data
registers and their functions are listed in the table below.
• For SR numbers marked “*”, Refer to the additional remarks in Section 2.2.1.6 on special auxiliary
relays/special data registers.
• The “R” in the attribute column indicates that the special data register can read the data; “R/W” in the attribute
column indicates that it can read and write the data.
• The “–” indicates that the status of the special data register does not make any change.
• The “#” indicates that the system is set according to the status of the PLC, and you can read the setting. Refer
to the related manual for more information.
• The “Y” in the column latched means it is latched, the “N” means it is non-latched; and “H” means it follows the
settings in HWCONFIG.
During execution, you can edit programs in the PLC, but the settings in the HWCONFIG do not change.
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN

Default
SR Function   
ON RUN STOP
SR0 PLC operation/operand error ○ ○ 0 0 - N R 0

SR1
The address of the operation error (32-bit) ○ ○ 0 0 - N R 0
SR2
SR4 Grammar check error ○ ○ 0 0 - N R 0
SR5
The address of the grammar check error (32-bit) ○ ○ 0 0 - N R 0
SR6
*SR8
Step address at which the watchdog timer is ON (32-bit) ○ ○ 0 - - N R 0
SR9
SR23 Number of times the MAC address is made ○ ○ - - - N R -
SM27 AS-F2AD: flags for buildt-in AD errors ○ ○ 0 - - N R/W 0
2-76
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR28
Last output number when the high speed output
○ ○ -1 -1 -1 N R -1
2_
instruction is used repeatedly
SR32 The last instruction address that exceeded the allowed
○ ○ -1 -1 - N R -1
SR33 range
System saves data to the memory card. This function
*SR36 ○ ○ 0 - - N R/W 0
works with SM36
*SR40 Number of error logs ○ ○ - - - Y R 0
*SR41 Error log pointer ○ ○ - - - Y R 0
*SR42 Error log 1: CPU or remote number ○ ○ - - - Y R 0
*SR43 Error log 1: module ID ○ ○ - - - Y R 0
*SR44 Error log 1: error code ○ ○ - - - Y R 0
*SR45 Error log 1: year and the month ○ ○ - - - Y R 0
*SR46 Error log 1: day and the hour ○ ○ - - - Y R 0
*SR47 Error log 1: minute and the second ○ ○ - - - Y R 0
2-77
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR74 Error log 6: error code ○ ○ - - - Y R 0

2-78
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR113 Error log 12: minute and the second ○ ○ - - - Y R 0 2_

SR142 Error log 17: day and the hour ○ ○ - - - Y R 0
2-79
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR152 Error log 19: error code ○ ○ - - - Y R 0

SR162 Length of time that the PLC is powered on (unit: minutes)
○ ○ - - - Y R -
SR163 (32-bit)
SR166 VR0 value (works with SM166) ○ - 0 - - N R 0
SR167 VR1 value (works with SM167) ○ - 0 - - N R 0
AS300 Series: Value in the channel 1 of the Function
*SR168 Card 1 F2AD ○ ○ 0 - - N R 0
AS218 Series: Value in the AD channel 1
*SR169 Card 1 F2AD ○ ○ 0 - - N R 0
AS218 Series: Value in the AD channel 2
*SR170 Value in the channel 1 of the Function Card 2 F2AD ○ - 0 - - N R 0
*SR171 Value in the channel 2 of the Function Card 2 F2AD ○ - 0 - - N R 0
*SR172 Card 1 F2DA ○ ○ 0 - 0 N R/W 0
AS218 Series: Value in the DA channel 1
*SR173 Card 1 F2DA ○ ○ 0 - 0 N R/W 0
AS218 Series: Value in the DA channel 2
*SR174 Value in the channel 1 of the Function Card 2 F2DA ○ - 0 - 0 N R/W 0
*SR175 Value in the channel 2 of the Function Card 2 F2DA ○ - 0 - 0 N R/W 0
SR176 The Function Card 1 communication ID (COM11) ○ - - - - N R 1
SR177 The Function Card 1 protocol code (COM11) ○ - - - - N R 0x24
SR178 The Function Card 2 communication ID (COM12) ○ - - - - N R 1
SR179 The Function Card 2 protocol code (COM12) ○ - - - - N R 0x24
SR180 The last warning error code ○ ○ 0 - - N R 0
Communication Card 1 (COM11) timeout duration (unit:
SR182 milliesecond). ○ - - - - N R/W 200
0: no timeout
Communication Card 2 (COM12) timeout duration (unit:
SR183 milliesecond). ○ - - - - N R/W 200
0: no timeout
2-80
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR185
The communication cycle time for all the remote modules
○ ○ 0 - - N R 0
2_
(unit: milliesecond)
SR187 Communication Card 1 (COM11) baud rate (unit: 100bps) ○ - 96 - - N R/W 96
SR188 Communication Card 2 (COM12 baud rate (unit: 100bps) ○ - 96 - - N R/W 96
Frequency multiplication of the high speed counter
SR190 ○ ○ 1 - - N R/W 1
group 1 (default: 1-time frequency)
SR191 ○ ○ 1 - - N R/W 1
SR192 ○ ○ 1 - - N R/W 1
SR193 ○ ○ 1 - - N R/W 1
SR194 ○ ○ 1 - - N R/W 1
SR195 ○ ○ 1 - - N R/W 1
SR196 ○ ○ 1 - - N R/W 1
SR197 ○ ○ 1 - - N R/W 1
16# 16# 16# 16#
SR198 N
0FDB 0FDB 0FDB 0FDB
Pi (π), floating-point number (32-bit) ○ ○ R
16# 16# 16# 16#
SR199 N
4049 4049 4049 4049
*SR201 COM1 communication address ○ ○ - - - H R/W 1
*SR202 COM2 communication address ○ ○ - - - H R/W 1
16#
*SR209 COM1 communication protocol ○ ○ - - - H R/W
0024
COM1 communication timeout (unit: milliesecond)
*SR210 ○ ○ - - - H R/W 0
0: no timeout
16#
*SR212 COM2 communication protocol ○ ○ - - - H R/W
0024
COM2 communication timeout (unit: milliesecond)
*SR213 ○ ○ - - - H R/W 0
0: no timeout
*SR215 Function Card 1 name ○ - - - - N R 0
*SR216 Function Card 2 Name ○ - - - - N R 0
SR217 COM1 baudrate value (unit:100 bps) ○ ○ 96 - - H R/W 96
SR218 COM2 baudrate value (unit:100 bps) ○ ○ 96 - - H R/W 96
*SR220 Real-time clock (RTC) year value: 00–99 (A.D.) ○ ○ - - - Y R 0
*SR221 Real-time clock (RTC) month value : 01–12 ○ ○ - - - Y R 1
*SR222 Real-time clock (RTC) day value : 1–31 ○ ○ - - - Y R 1
*SR223 Real-time clock (RTC) hour value: 00–23 ○ ○ - - - Y R 0
2-81
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR224 Real-time clock (RTC) minute value: 00–59 ○ ○ - - - Y R 0

*SR225 Real-time clock (RTC) second value: 00–59 ○ ○ - - - Y R 0
*SR226 Real-time clock (RTC) week value: 1–7 ○ ○ - - - Y R 1
*SR227 Number of download logs (maximum is 20) ○ ○ - - - Y R 0
*SR228 Download log pointer ○ ○ - - - Y R 0
*SR229 Download log 1: action number ○ ○ - - - Y R 0
*SR230 Download log 1: year and the month ○ ○ - - - Y R 0
*SR231 Download log 1: day and the hour ○ ○ - - - Y R 0
*SR232 Download log 1: minute and the second ○ ○ - - - Y R 0
2-82
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR263 Download log 9: day and the hour ○ ○ - - - Y R 0 2_

2-83
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR302 Download log 19: year and the month ○ ○ - - - Y R 0

*SR309 Number of PLC status change logs (maximum is 20) ○ ○ - - - Y R 0
*SR310 PLC status change log pointer ○ ○ - - - Y R 0
*SR311 PLC status change log 1: action number ○ ○ - - - Y R 0
*SR312 PLC status change log 1: year and the month ○ ○ - - - Y R 0
*SR313 PLC status change log 1: day and the hour ○ ○ - - - Y R 0
*SR314 PLC status change log 1: minute and the second ○ ○ - - - Y R 0
2-84
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR341 PLC status change log 8: day and the hour ○ ○ - - - Y R 0 2_

2-85
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR380 PLC status change log 18: year and the month ○ ○ - - - Y R 0
*SR391 Real-time clock (RTC) year value: 00–99 (A.D.) ○ ○ - - - Y R 0
*SR392 Real-time clock (RTC) month value: 01–12 ○ ○ - - - Y R 1
*SR393 Real-time clock (RTC) day value: 1–31 ○ ○ - - - Y R 1
*SR394 Real-time clock (RTC) hour value: 00–23 ○ ○ - - - Y R 0
*SR395 Real-time clock (RTC) minute value: 00–59 ○ ○ - - - Y R 0
*SR396 Real-time clock (RTC) second value: 00–59 ○ ○ - - - Y R 0
*SR397 Real-time clock (RTC) week value: 1–7 ○ ○ - - - Y R 1
PLC main processor firmware version
SR405 ○ ○ - - - Y R -
(e.g. 10670 = V1.06.70)
PLC sub-processor firmware version (e.g. 0 = no sub-
SR406 ○ ○ - - - Y R -
processor)
When the PLC runs, the value in SR407 increases by one
SR407 every second. SR407 counts from 0 to 32767, and then ○ ○ 0 0 - N R/W 0
from -32768 to 0.
When the PLC runs, the value in SR408 increases by one
SR408 every scan cycle. SR408 counts from 0 to 32767, and ○ ○ 0 0 - N R/W 0
then from -32768 to 0.
SR411 The current scan time is stored in SR411 and SR412 (unit ○ ○ 0 - - N R 0
of measurement is 100 microseconds).
Milliseconds are stored in SR411 (range is 0–65535).
SR412 Microseconds are stored in SR412 (the range is 0–900). ○ ○ 0 - - N R 0
For example, if SR411=12 and SR412=300, then the
current scan time is 12.3 milliseconds.
SR413 The maximum scan time is stored in SR413 and SR414
(unit of measurement is 100 microseconds). The value of ○ ○ 0 - - N R 0
SR414
the millisecond is stored in SR413.
SR415 The minimum scan time is stored in SR415 and SR416
(unit of measurement is 100 microseconds). The value of ○ ○ 0 - - N R 0
SR416
the millisecond is stored in SR415.
2-86
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
Duration of the timer interrupt I601 (unit: milliesecond). 2_

SR421 The default is 0, meaning the system uses the settings in ○ ○ 0 0 - N R/W 0
HWCONFIG.
Duration of the timer interrupt I602 (unit: milliesecond).
HWCONFIG.
Duration of the timer interrupt I603 (unit: milliesecond).
HWCONFIG.
Duration of the timer interrupt I604 (unit: 0.1 milliesecond).
HWCONFIG.
SR440 MAC address ○ ○ - - - Y R -

(Example: 12:34:56:78:9A:BC => SR440=16#1234,
SR441 ○ ○ - - - Y R -
SR441=16#5678, SR442=16#9ABC)
SR442 (Updates once, when the PLC is supplied with power) ○ ○ - - - Y R -
SR443 PLC series ○ ○ - - - Y R -

SR444 EX：AS324MTAW15500012 ○ ○ - - - Y R -
SR445 AS SR443 = 16#5341 ○ ○ - - - Y R -
SR446 32  SR444 = 16#3233 ○ ○ - - - Y R -
SR447 4M  SR445 = 16#4D34 ○ ○ - - - Y R -
TA  SR446 = 16#4154
SR448 ○ ○ - - - Y R -
W1  SR447 = 16#3157
SR449 ○ ○ - - - Y R -
55  SR448 = 16#3535
SR450 ○ ○ - - - Y R -
00  SR449 = 16#3030
01  SR450 = 16#3130
SR451 2  SR451 = 16#0032 ○ ○ - - - Y R -
(Updates once, when the PLC is supplied with power)
If an error occurs during the operation of the memory
*SR453 ○ ○ - - - Y R 0
card, the error code is recorded.
SR460
Y0.0/axis 1 (Y0.0/Y0.1) position (unit: number of pulse) ○ ○ - - - Y R/W 0
SR461
SR462 Axis 1 (Y0.0/Y0.1) output mode ○ ○ - - - Y R/W 0
SR463 Axis 1 (Y0.0/Y0.1) starting/ending frequency ○ ○ - - - Y R/W 200
SR464 Axis 1 (Y0.0/Y0.1) accelerating time ○ ○ - - - Y R/W 200
SR465 Axis 1 (Y0.0/Y0.1) decelerating time ○ ○ - - - Y R/W 200
SR466 Axis 1 (Y0.0/Y0.1) JOG frequency ○ ○ - - - Y R/W 200
Axis 1 (Y0.0/Y0.1) number in the current position planning
SR467 ○ ○ 0 0 - N R 0
table
Axis 1 (Y0.0/Y0.1) numerator value transferred from the
SR468 ○ ○ - - - H R/W 0
machine unit
2-87
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR469
Axis 1 (Y0.0/Y0.1) denominator value transferred from the
○ ○ - - - H R/W 0
machine unit
SR470 Axis 1 (Y0.0/Y0.1) position of the machine unit (single-
○ ○ - - - Y R 0
SR471 precision floating-point values)
SR472
Axis 1 (Y0.0/Y0.1) target frequency for fixed slope ○ ○ - - - Y R 0
SR473
SR474
Y0.1 position (unit: number of pulse) ○ ○ - - - Y R/W 0
SR475
SR476 Y0.1 starting/ending frequency ○ ○ - - - Y R/W 200
SR477 Y0.1 accelerating/decelerating time ○ ○ - - - Y R/W 200
SR478 Axis 1 (Y0.0) backlash compensation pulse ○ ○ - - - Y R/W 0
SR479 Y0.1 backlash compensation pulse ○ ○ - - - Y R/W 0
SR480
SR481
SR482 Y0.2/axis 2 (Y0.2/Y0.3) output mode ○ ○ - - - Y R/W 0
SR483 Y0.2/axis 2 (Y0.2/Y0.3) starting/ending frequency ○ ○ - - - Y R/W 200
SR484 Y0.2/axis 2 (Y0.2/Y0.3) accelerating time ○ ○ - - - Y R/W 200
SR485 Y0.2/axis 2 (Y0.2/Y0.3) decelerating time ○ ○ - - - Y R/W 200
SR486 Y0.2/axis 2 (Y0.2/Y0.3) JOG frequency ○ ○ - - - Y R/W 200
Y0.2/axis 2 (Y0.2/Y0.3) number in the current position
SR487 ○ ○ 0 0 - N R 0
planning table
Y0.2/axis 2 (Y0.2/Y0.3) numerator value transferred from
SR488 ○ ○ - - - H R/W 0
the machine unit
Y0.2/axis 2 (Y0.2/Y0.3) denominator value transferred
SR489 ○ ○ - - - H R/W 0
from the machine unit
SR490 Y0.2/axis 2 (Y0.2/Y0.3) position of the Machine unit
○ ○ - - - Y R 0
SR491 (single-precision floating-point values)
SR492
Y0.2/axis 2 (Y0.2/Y0.3) target frequency for fixed slope ○ ○ - - - Y R 0
SR493
SR494
SR495
SR500
SR501
2-88
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR505 Y0.4/axis 3 (Y0.4/Y0.5) decelerating time ○ ○ - - - Y R/W 200 2_

SR507 ○ ○ 0 0 - N R 0
planning table
SR508 ○ ○ - - - H R/W 0
the machine unit
SR509 ○ ○ - - - H R/W 0
○ ○ - - - Y R 0
SR512
SR513
SR514
SR515
SR520
SR521
SR527 ○ ○ 0 0 - N R 0
planning table
SR528 ○ ○ - - - H R/W 0
the machine unit
SR529 ○ ○ - - - H R/W 0
SR530 Y0.6/axis 4 (Y0.6/Y0.7) position of the Machine
○ ○ - - - Y R 0
SR531 unit(single-precision floating-point values)
SR532
SR533
SR534
SR535
2-89
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR539 Y0.7 backlash compensation pulse ○ ○ - - - Y R/W 0

SR540 Y0.8/axis 5 (Y0.8/Y0.9) position where (unit: number of
○ ○ - - - Y R/W 0
SR541 pulse)
SR542 The axis 5 (Y0.8/Y0.9) output mode ○ ○ - - - Y R/W 0
Y0.8/axis 5 (Y0.8/Y0.9)number in the current position
SR547 ○ ○ 0 0 - N R 0
planning table
SR548 ○ ○ - - - H R/W 0
the machine unit
SR549 ○ ○ - - - H R/W 0
○ ○ - - - Y R 0
SR552
SR553
SR554
SR555
SR560 Y0.10/axis 6 (Y0.10/Y0.11) position (unit: number of
○ ○ - - - Y R/W 0
SR561 pulse)

SR567 ○ ○ 0 0 - N R 0
planning table
Y0.10/axis 6 (Y0.10/Y0.11) numerator value transferred
SR568 ○ ○ - - - H R/W 0
SR569 ○ ○ - - - H R/W 0
○ ○ - - - Y R 0
SR572 ○ ○ - - - Y R 0
2-90
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR573
Y0.10/axis 6 (Y0.10/Y0.11) target frequency for fixed 2_
slope
SR574
SR575
*SR580 Axis 1 (Y0.0/Y0.1) positive limit in ISPSoft (unit: number of
○ ○ - - - H R/W 0
*SR581 pulse)
*SR582 Axis 1 (Y0.0/Y0.1) negative limit in ISPSoft (unit: number
○ ○ - - - H R/W 0
*SR583 of pulse)
*SR584 Axis 2 (Y0.2/Y0.3) positive limit in ISPSoft (unit: number of
○ ○ - - - H R/W 0
*SR585 pulse)
*SR586 Axis 2 (Y0.2/Y0.3) negative limit in ISPSoft (unit: number
○ ○ - - - H R/W 0
*SR587 of pulse)
*SR588 Axis 3(Y0.4/Y0.5) positive limit in ISPSoft (unit: number of
○ ○ - - - H R/W 0
*SR589 pulse)
*SR590 Axis 3(Y0.4/Y0.5) negative limit in ISPSoft (unit: number
○ ○ - - - H R/W 0
*SR591 of pulse)
○ ○ - - - H R/W 0
*SR593 pulse)
○ ○ - - - H R/W 0
*SR595 of pulse)
○ ○ - - - H R/W 0
*SR597 pulse)
○ ○ - - - H R/W 0
*SR599 of pulse)
*SR600 Axis 6(Y0.10/Y0.11) positive limit in ISPSoft (unit:
○ ○ - - - H R/W 0
*SR601 number of pulse)
*SR602 Axis 6(Y0.10/Y0.11) negative limit in ISPSoft (unit:

○ ○ - - - H R/W 0
*SR603 number of pulse)
*SR604 Axis 1 (Y0.0/Y0.1) S curve mode ○ ○ 0 - - N R/W 0

SR610 Axis 1 (Y0.0/Y0.1) current output speed (unit: Hz) ○ ○ 0 0 0 N R 0
2-91
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR611
SR612
axis 2 (Y0.2/Y0.3) current output speed (unit: Hz) ○ ○ 0 0 0 N R 0
SR613
SR614
Axis 3 (Y0.4/Y0.5) current output speed (unit: Hz) ○ ○ 0 0 0 N R 0
SR615
SR616
SR617
SR618
SR619
SR620
SR621
External interrupt condition: the X0.0–X0.15 input points
SR623 ○ ○ FFFF FFFF - N R FFFF
are falling-edge triggered
External interrupt condition: the X0.0–X0.15 input points
are rising-edge triggered
Condition of the high-speed comparison interrupt I200–
I233
I253
I267
SR628 Condition of the communication interrupts I300–I307 ○ ○ FFFF FFFF - N R FFFF
SR629 Condition of the output interrupts I500–I505 ○ ○ FFFF FFFF - N R FFFF
SR630 Condition of the output interrupts I510–I519 ○ ○ FFFF FFFF - N R FFFF
SR632 Condition of the timer interrupts I601–I604 ○ ○ FFFF FFFF - N R FFFF
SR633 Condition of the extension module interrupts I400–I415 ○ ○ FFFF FFFF - N R FFFF
SR634 Condition of the extension module interrupts I416–I431 ○ ○ FFFF FFFF - N R FFFF
Set the outputting time 0-20ms sooner (unit: 1ms) to work
SR640 ○ ○ 0 - - N R/W 0
with the Y0.0 output pulse
SR641 ○ ○ 0 - - N R/W 0
SR642 ○ ○ 0 - - N R/W 0
SR643 ○ ○ 0 - - N R/W 0
SR644 ○ ○ 0 - - N R/W 0
SR645 ○ ○ 0 - - N R/W 0
SR646 ○ ○ 0 - - N R/W 0
2-92
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR647
○ ○ 0 - - N R/W 0
2_
SR648 ○ ○ 0 - - N R/W 0
SR649 ○ ○ 0 - - N R/W 0
SR650 ○ ○ 0 - - N R/W 0
SR651 ○ ○ 0 - - N R/W 0
Pulse number in acceleration from the latest position
*SR652 ○ ○ 0 0 - N R 0
output (lower 16 bits)
Pulse number in acceleration from the latest position
*SR653 ○ ○ 0 0 - N R 0
output (higher 16 bits)
Pulse number in deceleration from the latest position
*SR654 ○ ○ 0 0 - N R 0
output (lower 16 bits)
Pulse number in deceleration from the latest position
*SR655 ○ ○ 0 0 - N R 0
output (higher 16 bits)
The number of the Delta CANopen communication axis
SR658 ○ ○ 0 - - N R 0
from the Delta servo which has a communication error
SR659 Delta CANopen communication error ○ ○ 0 - - N R 0
The PR command of the Delta CANopen communication
SR661 ○ ○ 0 - - N R 0
axis 1 from the Delta servo
PR command of the Delta CANopen communication axis
SR662 ○ ○ 0 - - N R 0
2 from the Delta servo
SR663 ○ ○ 0 - - N R 0
SR664 ○ ○ 0 - - N R 0
SR665 ○ ○ 0 - - N R 0
SR666 ○ ○ 0 - - N R 0
SR667 ○ ○ 0 - - N R 0
SR668 ○ ○ 0 - - N R 0
Alarm code of the Delta CANopen communication axis 1
SR671 ○ ○ 0 - - N R 0
from the Delta servo
SR672 ○ ○ 0 - - N R 0
SR673 ○ ○ 0 - - N R 0
2-93
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR674
○ ○ 0 - - N R 0
SR675 ○ ○ 0 - - N R 0
SR676 ○ ○ 0 - - N R 0
SR677 ○ ○ 0 - - N R 0
SR678 ○ ○ 0 - - N R 0
The DO state of the Delta CANopen communication axis
SR681 ○ ○ 0 - - N R 0
SR682 ○ ○ 0 - - N R 0
SR683 ○ ○ 0 - - N R 0
SR684 ○ ○ 0 - - N R 0
SR685 ○ ○ 0 - - N R 0
SR686 ○ ○ 0 - - N R 0
SR687 ○ ○ 0 - - N R 0
SR688 ○ ○ 0 - - N R 0
SR691 Current position of the Delta CANopen communication
○ ○ 0 - - N R 0
SR692 axis 1 from the Delta servo (32-bit)
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
2-94
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR711 Target position of the Delta CANopen communication axis 2_

○ ○ 0 - - N R 0
SR712 1 from the Delta servo (32-bit)
SR713 Target position of the Delta CANopen communication axis
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
○ ○ 0 - - N R 0
Current DI state of Delta CANopen communication ID 1
SR731 ○ ○ 0 - - N R 0
SR732 ○ ○ 0 - - N R 0
SR733 ○ ○ 0 - - N R 0
SR734 ○ ○ 0 - - N R 0
SR735 ○ ○ 0 - - N R 0
SR736 ○ ○ 0 - - N R 0
SR737 ○ ○ 0 - - N R 0
SR738 ○ ○ 0 - - N R 0
Current torque of Delta CANopen communication ID 1
SR741 ○ ○ 0 - - N R 0
from the Delta servo (unit: 0.1%)
SR742 ○ ○ 0 - - N R 0
SR743 ○ ○ 0 - - N R 0
SR744 ○ ○ 0 - - N R 0
SR745 ○ ○ 0 - - N R 0
2-95
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR746
○ ○ 0 - - N R 0
SR747 ○ ○ 0 - - N R 0
SR748 ○ ○ 0 - - N R 0
Current state of Delta CANopen communication slave ID
SR751 ○ ○ 0 - - N R 0
21 from the Delta inverter
SR752 ○ ○ 0 - - N R 0
SR753 ○ ○ 0 - - N R 0
SR754 ○ ○ 0 - - N R 0
SR755 ○ ○ 0 - - N R 0
SR756 ○ ○ 0 - - N R 0
SR757 ○ ○ 0 - - N R 0
SR758 ○ ○ 0 - - N R 0
Current RPM of Delta CANopen communication slave ID
SR761 ○ ○ 0 - - N R 0
SR762 ○ ○ 0 - - N R 0
SR763 ○ ○ 0 - - N R 0
SR764 ○ ○ 0 - - N R 0
SR765 ○ ○ 0 - - N R 0
SR766 ○ ○ 0 - - N R 0
SR767 ○ ○ 0 - - N R 0
SR768 ○ ○ 0 - - N R 0
SR771 ○ ○ 0 - - N R 0
from the Delta inverter (unit: 0.1%)
SR772 ○ ○ 0 - - N R 0
SR773 ○ ○ 0 - - N R 0
2-96
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR774
○ ○ 0 - - N R 0
2_
SR775 ○ ○ 0 - - N R 0
SR776 ○ ○ 0 - - N R 0
SR777 ○ ○ 0 - - N R 0
SR778 ○ ○ 0 - - N R 0
SR781 ○ ○ 0 - - N R 0
from the Delta inverter
SR782 ○ ○ 0 - - N R 0
SR783 ○ ○ 0 - - N R 0
SR784 ○ ○ 0 - - N R 0
SR785 ○ ○ 0 - - N R 0
SR786 ○ ○ 0 - - N R 0
SR787 ○ ○ 0 - - N R 0
SR788 ○ ○ 0 - - N R 0
Read the self-defined value from Delta CANopen
SR791 ○ ○ 0 - - N R 0
communication axis 1 (lower 16 bits)
SR792 ○ ○ 0 - - N R 0
communication axis 1 (higher16 bits)
SR793 ○ ○ 0 - - N R 0
SR794 ○ ○ 0 - - N R 0
SR795 ○ ○ 0 - - N R 0
SR796 ○ ○ 0 - - N R 0
SR797 ○ ○ 0 - - N R 0
SR798 ○ ○ 0 - - N R 0
SR799 ○ ○ 0 - - N R 0
2-97
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR800
○ ○ 0 - - N R 0
SR801 ○ ○ 0 - - N R 0
SR802 ○ ○ 0 - - N R 0
SR803 ○ ○ 0 - - N R 0
SR804 ○ ○ 0 - - N R 0
SR805 ○ ○ 0 - - N R 0
SR806 ○ ○ 0 - - N R 0
The setting value for the Delta CANopen communication
axis 1 to complete positioning.
(If the setting value is 0, it indicates the current position
SR811 should be the same as the target position to complete the ○ ○ 0 - - N RW 0
positioning. If the setting value is 5, it indicates the
distance between the current position and the target
position can be +5 to -5 to complete the positioning.)
SR812 ○ ○ 0 - - N RW 0
SR813 ○ ○ 0 - - N RW 0
SR814 ○ ○ 0 - - N RW 0
SR815 ○ ○ 0 - - N RW 0
SR816 ○ ○ 0 - - N RW 0
SR817 ○ ○ 0 - - N RW 0
SR818 ○ ○ 0 - - N RW 0
Code for the state of the master/slave in CANopen DS301
SR820 ○ ○ - - - Y R 0
communication
SR821 CANopen DS301 version code ○ ○ - - - Y R -
SR822 CANopen communication baudrate (unit: 1kbps) ○ ○ - - - H R 125
The number of hardware receiving error during CANopen
*SR823 ○ ○ 0 - - N R 0
communication (Max. 255)
The number of hardware sending error during CANopen
*SR824 ○ ○ 0 - - N R 0
communication (Max. 255)
Code for the master state in CANopen DS301
SR825 ○ ○ -1 - - N R -1
communication
2-98
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR826
State of slave ID 1–16 in CANopen DS301
○ ○ -1 - - N R -1
2_
communication
SR827 ○ ○ -1 - - N R -1
communication
SR828 ○ ○ -1 - - N R -1
communication
SR829 ○ ○ -1 - - N R -1
communication
SR830 State of slave ID 1 in CANopen DS301 communication ○ ○ -1 - - N R -1
2-99
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR862 State of slave ID 33 in CANopen DS301 communication ○ ○ -1 - - N R -1

SR865 State of slave ID 36in CANopen DS301 communication ○ ○ -1 - - N R -1
SR900 ○
Number of samples in the data logger (32-bit) ○ 0 - - N R 0
SR901 ○
Code for the executions of data logger and the memory
SR902 card (works with SM456). For example, H5AA5: write the ○ ○ 0 - - N R/W 0
sampling data from the data logger into the memory card.
*SR1000 ○
Ethernet IP address (32-bit) ○ - - - H R/W 0
*SR1001 ○
2-100
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR1002 ○ 2_
Ethernet netmask address (32-bit) ○ - - - H R/W 0
*SR1003 ○
*SR1004 ○
Ethernet gateway address (32-bit) ○ - - - H R/W 0
*SR1005 ○
*SR1006 Duration of the TCP connection (sec.) ○ ○ - - - H R/W 30
*SR1007 Ethernet transmission speed ○ ○ 0 - - N R 0
*SR1009 Number of TCP connections ○ ○ 0 - - N R 0
Specific time when to resend through the TCP connection
*SR1010 ○ ○ - - - N R/W 20
(ms)
*SR1011 Connection number of the MODBUS/TCP Server ○ ○ 0 - - N R 0
*SR1012 Connection number of the MODBUS/TCP Client ○ ○ 0 - - N R 0
*SR1013 Connection number of the EtherNet/IP Adapter ○ ○ 0 - - N R 0
*SR1014 Connection number of the EtherNet/IP Scanner ○ ○ 0 - - N R 0
*SR1015 MODBUS/TCP Server packet receiving timeout (ms) ○ ○ 10 - - N R/W 10
*SR1020 State of the EtherNet/IP connection 1 ○ 0 - - N R 0
*SR1021 State of the EtherNet/IP connection 2 ○ ○ 0 - - N R 0
2-101
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1046 State of the EtherNet/IP connection 27 ○ ○ 0 - - N R 0

SR1052 Refresh time for the EtherNet/IP connection 1 ○ ○ 0 - - N R 0
SR1100 Value of the input packet counter (32-bit) ○ ○ 0 - - N R 0
2-102
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR1101 ○ 2_
SR1102 ○
Value of the input octet counter (32-bit) ○ 0 - - N R 0
SR1103 ○
SR1104 ○
Value of the output packet counter (32-bit) ○ 0 - - N R 0
SR1105 ○
SR1106 ○
Value of the output octet counter (32-bit) ○ 0 - - N R 0
SR1107 ○
SR1116 Email counter ○ ○ 0 - - N R 0
SR1117 Email error counter ○ ○ 0 - - N R 0
Actual connection time for data exchange through the
*SR1120 ○ ○ 0 - - N R 0
Ethernet connection 1
*SR1121 ○ ○ 0 - - N R 0
*SR1122 ○ ○ 0 - - N R 0
*SR1123 ○ ○ 0 - - N R 0
*SR1124 ○ ○ 0 - - N R 0
*SR1125 ○ ○ 0 - - N R 0
*SR1126 ○ ○ 0 - - N R 0
*SR1127 ○ 0 - - N R 0
*SR1128 ○ ○ 0 - - N R 0
*SR1129 ○ 0 - - N R 0
*SR1130 ○ ○ 0 - - N R 0
*SR1131 ○ 0 - - N R 0
*SR1132 ○ 0 - - N R 0
*SR1133 ○ ○ 0 - - N R 0
*SR1134 ○ 0 - - N R 0
*SR1135 ○ ○ 0 - - N R 0
*SR1136 ○ ○ 0 - - N R 0
2-103
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1137
○ ○ 0 - - N R 0
*SR1138 ○ ○ 0 - - N R 0
*SR1139 ○ ○ 0 - - N R 0
*SR1140 ○ ○ 0 - - N R 0
*SR1141 ○ ○ 0 - - N R 0
*SR1142 ○ ○ 0 - - N R 0
*SR1143 ○ ○ 0 - - N R 0
*SR1144 ○ ○ 0 - - N R 0
*SR1145 ○ ○ 0 - - N R 0
*SR1146 ○ ○ 0 - - N R 0
*SR1147 ○ ○ 0 - - N R 0
*SR1148 ○ ○ 0 - - N R 0
*SR1149 ○ ○ 0 - - N R 0
*SR1150 ○ ○ 0 - - N R 0
*SR1151 ○ ○ 0 - - N R 0
The error code for data exchange through the Ethernet
*SR1152 ○ ○ 0 - - N R 0
connection 1
*SR1153 ○ ○ 0 - - N R 0
connection 2
*SR1154 ○ ○ 0 - - N R 0
connection 3
*SR1155 ○ ○ 0 - - N R 0
connection 4
*SR1156 ○ ○ 0 - - N R 0
connection 5
*SR1157 ○ ○ 0 - - N R 0
connection 6
*SR1158 ○ ○ 0 - - N R 0
connection 7
2-104
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR1159
○ ○ 0 - - N R 0
2_
connection 8
*SR1160 ○ ○ 0 - - N R 0
connection 9
*SR1161 ○ ○ 0 - - N R 0
connection 10
*SR1162 ○ ○ 0 - - N R 0
connection 11
*SR1163 ○ ○ 0 - - N R 0
connection 12
*SR1164 ○ ○ 0 - - N R 0
connection 13
*SR1165 ○ ○ 0 - - N R 0
connection 14
*SR1166 ○ ○ 0 - - N R 0
connection 15
*SR1167 ○ ○ 0 - - N R 0
connection 16
*SR1168 ○ ○ 0 - - N R 0
connection 17
*SR1169 ○ ○ 0 - - N R 0
connection 18
*SR1170 ○ ○ 0 - - N R 0
connection 19
*SR1171 ○ ○ 0 - - N R 0
connection 20
*SR1172 ○ ○ 0 - - N R 0
connection 21
*SR1173 ○ ○ 0 - - N R 0
connection 22
*SR1174 ○ ○ 0 - - N R 0
connection 23
*SR1175 ○ ○ 0 - - N R 0
connection 24
*SR1176 ○ ○ 0 - - N R 0
connection 25
*SR1177 ○ ○ 0 - - N R 0
connection 26
*SR1178 ○ ○ 0 - - N R 0
connection 27
*SR1179 ○ ○ 0 - - N R 0
connection 28
*SR1180 ○ ○ 0 - - N R 0
connection 29
2-105
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1181
○ ○ 0 - - N R 0
connection 30
*SR1182 ○ ○ 0 - - N R 0
connection 31
*SR1183 ○ ○ 0 - - N R 0
connection 32
*SR1312 Communication code for RTU-EN01 connection 1 ○ ○ 0 - - N R 0
SR1318 Socket input counter ○ ○ 0 - - N R 0
SR1319 Socket output counter ○ ○ 0 - - N R 0
SR1320 Socket error counter ○ ○ 0 - - N R 0
Actual cycle time of connection 1–32 for data exchange
*SR1335 ○ ○ 0 - - N R 0
through COM1
Number of the connection that is currently performing a
*SR1336 ○ ○ 0 - - N R 0
cyclical data exchange through COM1
Error code for data exchange through the COM1
*SR1340 ○ ○ 0 - - N R 0
connection 1
*SR1341 ○ ○ 0 - - N R 0
connection 2
*SR1342 ○ ○ 0 - - N R 0
connection 3
*SR1343 ○ ○ 0 - - N R 0
connection 4
*SR1344 ○ ○ 0 - - N R 0
connection 5
*SR1345 ○ ○ 0 - - N R 0
connection 6
*SR1346 ○ ○ 0 - - N R 0
connection 7
*SR1347 ○ ○ 0 - - N R 0
connection 8
*SR1348 ○ ○ 0 - - N R 0
connection 9
*SR1349 ○ ○ 0 - - N R 0
connection 10
*SR1350 ○ ○ 0 - - N R 0
connection 11
*SR1351 ○ ○ 0 - - N R 0
connection 12
*SR1352 ○ ○ 0 - - N R 0
connection 13
2-106
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR1353
○ ○ 0 - - N R 0
2_
connection 14
*SR1354 ○ ○ 0 - - N R 0
connection 15
*SR1355 ○ ○ 0 - - N R 0
connection 16
*SR1356 ○ ○ 0 - - N R 0
connection 17
*SR1357 ○ ○ 0 - - N R 0
connection 18
*SR1358 ○ ○ 0 - - N R 0
connection 19
*SR1359 ○ ○ 0 - - N R 0
connection 20
*SR1360 ○ ○ 0 - - N R 0
connection 21
*SR1361 ○ ○ 0 - - N R 0
connection 22
*SR1362 ○ ○ 0 - - N R 0
connection 23
*SR1363 ○ ○ 0 - - N R 0
connection 24
*SR1364 ○ ○ 0 - - N R 0
connection 25
*SR1365 ○ ○ 0 - - N R 0
connection 26
*SR1366 ○ ○ 0 - - N R 0
connection 27
*SR1367 ○ ○ 0 - - N R 0
connection 28
*SR1368 ○ ○ 0 - - N R 0
connection 29
*SR1369 ○ ○ 0 - - N R 0
connection 30
*SR1370 ○ ○ 0 - - N R 0
connection 31
*SR1371 ○ ○ 0 - - N R 0
connection 32
Actual cycle time of connection 1–32 for data exchange
*SR1375 ○ ○ 0 - - N R 0
through COM2
*SR1376 ○ ○ 0 - - N R 0
cyclical data exchange through COM2
*SR1380 ○ ○ 0 - - N R 0
connection 1
2-107
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 SR1381
○ ○ 0 - - N R 0
connection 2
SR1382 ○ ○ 0 - - N R 0
connection 3
SR1383 ○ ○ 0 - - N R 0
connection 4
SR1384 ○ ○ 0 - - N R 0
connection 5
SR1385 ○ ○ 0 - - N R 0
connection 6
SR1386 ○ ○ 0 - - N R 0
connection 7
SR1387 ○ ○ 0 - - N R 0
connection 8
SR1388 ○ ○ 0 - - N R 0
connection 9
SR1389 ○ ○ 0 - - N R 0
connection 10
SR1390 ○ ○ 0 - - N R 0
connection 11
SR1391 ○ ○ 0 - - N R 0
connection 12
SR1392 ○ ○ 0 - - N R 0
connection 13
SR1393 ○ ○ 0 - - N R 0
connection 14
SR1394 ○ ○ 0 - - N R 0
connection 15
SR1395 ○ ○ 0 - - N R 0
connection 16
SR1396 ○ ○ 0 - - N R 0
connection 17
SR1397 ○ ○ 0 - - N R 0
connection 18
SR1398 ○ ○ 0 - - N R 0
connection 19
SR1399 ○ ○ 0 - - N R 0
connection 20
SR1400 ○ ○ 0 - - N R 0
connection 21
SR1401 ○ ○ 0 - - N R 0
connection 22
SR1402 ○ ○ 0 - - N R 0
connection 23
2-108
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
SR1403
○ ○ 0 - - N R 0
2_
connection 24
SR1404 ○ ○ 0 - - N R 0
connection 25
SR1405 ○ ○ 0 - - N R 0
connection 26
SR1406 ○ ○ 0 - - N R 0
connection 27
SR1407 ○ ○ 0 - - N R 0
connection 28
SR1408 ○ ○ 0 - - N R 0
connection 29
SR1409 ○ ○ 0 - - N R 0
connection 30
SR1410 ○ ○ 0 - - N R 0
connection 31
SR1411 ○ ○ 0 - - N R 0
connection 32
Actual cycle time for data exchange through Function
*SR1435 ○ - 0 - - N R 0
Card 1
*SR1436 ○ - 0 - - N R 0
cyclical data exchange through Function Card 1
Error in data exchange connection 1 through Function
*SR1440 ○ - 0 - - N R 0
Card 1
*SR1441 ○ - 0 - - N R 0
Card 1
*SR1442 ○ - 0 - - N R 0
Card 1
*SR1443 ○ - 0 - - N R 0
Card 1
*SR1444 ○ - 0 - - N R 0
Card 1
*SR1445 ○ - 0 - - N R 0
Card 1
*SR1446 ○ - 0 - - N R 0
Card 1
*SR1447 ○ - 0 - - N R 0
Card 1
*SR1448 ○ - 0 - - N R 0
Card 1
*SR1449 ○ - 0 - - N R 0
Card 1
*SR1450 ○ - 0 - - N R 0
Card 1
2-109
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1451
○ - 0 - - N R 0
Card 1
*SR1452 ○ - 0 - - N R 0
Card 1
*SR1453 ○ - 0 - - N R 0
Card 1
*SR1454 ○ - 0 - - N R 0
Card 1
*SR1455 ○ - 0 - - N R 0
Card 1
*SR1456 ○ - 0 - - N R 0
Card 1
*SR1457 ○ - 0 - - N R 0
Card 1
*SR1458 ○ - 0 - - N R 0
Card 1
*SR1459 ○ - 0 - - N R 0
Card 1
*SR1460 ○ - 0 - - N R 0
Card 1
*SR1461 ○ - 0 - - N R 0
Card 1
*SR1462 ○ - 0 - - N R 0
Card 1
*SR1463 ○ - 0 - - N R 0
Card 1
*SR1464 ○ - 0 - - N R 0
Card 1
*SR1465 ○ - 0 - - N R 0
Card 1
*SR1466 ○ - 0 - - N R 0
Card 1
*SR1467 ○ - 0 - - N R 0
Card 1
*SR1468 ○ - 0 - - N R 0
Card 1
*SR1469 ○ - 0 - - N R 0
Card 1
*SR1470 ○ - 0 - - N R 0
Card 1
*SR1471 ○ - 0 - - N R 0
Card 1
Actual cycle time for data exchange through Function
*SR1475 ○ - 0 - - N R 0
Card 2
2 - 11 0
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR1476
○ - 0 - - N R 0
2_
cyclical data exchange through Function Card 2
*SR1480 ○ - 0 - - N R 0
Card 2
*SR1481 ○ - 0 - - N R 0
Card 2
*SR1482 ○ - 0 - - N R 0
Card 2
*SR1483 ○ - 0 - - N R 0
Card 2
SR1484 ○ - 0 - - N R 0
Card 2
*SR1485 ○ - 0 - - N R 0
Card 2
*SR1486 ○ - 0 - - N R 0
Card 2
*SR1487 ○ - 0 - - N R 0
Card 2
*SR1488 ○ - 0 - - N R 0
Card 2
*SR1489 ○ - 0 - - N R 0
Card 2
*SR1490 ○ - 0 - - N R 0
Card 2
*SR1491 ○ - 0 - - N R 0
Card 2
*SR1492 ○ - 0 - - N R 0
Card 2
*SR1493 ○ - 0 - - N R 0
Card 2
*SR1494 ○ - 0 - - N R 0
Card 2
*SR1495 ○ - 0 - - N R 0
Card 2
*SR1496 ○ - 0 - - N R 0
Card 2
*SR1497 ○ - 0 - - N R 0
Card 2
*SR1498 ○ - 0 - - N R 0
Card 2
*SR1499 ○ - 0 - - N R 0
Card 2
*SR1500 ○ - 0 - - N R 0
Card 2
2 - 111
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1501
○ - 0 - - N R 0
Card 2
*SR1502 ○ - 0 - - N R 0
Card 2
*SR1503 ○ - 0 - - N R 0
Card 2
*SR1504 ○ - 0 - - N R 0
Card 2
*SR1505 ○ - 0 - - N R 0
Card 2
*SR1506 ○ - 0 - - N R 0
Card 2
*SR1507 ○ - 0 - - N R 0
Card 2
*SR1508 ○ - 0 - - N R 0
Card 2
*SR1509 ○ - 0 - - N R 0
Card 2
*SR1510 ○ - 0 - - N R 0
Card 2
*SR1511 ○ - 0 - - N R 0
Card 2
The actual communication time for data exchange
*SR1520 ○ - 0 - - N R 0
connection 1 through AS-FEN02
*SR1521 ○ - 0 - - N R 0
*SR1522 ○ - 0 - - N R 0
*SR1523 ○ - 0 - - N R 0
*SR1524 ○ - 0 - - N R 0
*SR1525 ○ - 0 - - N R 0
*SR1526 ○ - 0 - - N R 0
*SR1527 ○ - 0 - - N R 0
*SR1528 Error in data exchange connection 1 through AS-FEN02 ○ - 0 - - N R 0
2 - 11 2
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
*SR1533 Error in data exchange connection 6 through AS-FEN02 ○ - 0 - - N R 0 2_

*SR1536 Number of TCP connections through AS-FEN02 ○ - 0 - - N R 0
Number of MODBUS/TCP Server connections through
*SR1537 ○ - 0 - - N R 0
AS-FEN02
Number of MODBUS/TCP Client connections through AS-
*SR1538 ○ - 0 - - N R 0
FEN02
Number of EtherNet/IP Adapter connections through AS-
*SR1539 ○ - 0 - - N R 0
FEN02
Number of the remote modules connected to the CPU
*SR1559 ○ ○ 0 - - N R 0
module (all right-side modules not included)
Number of the right-side modules connected to the CPU
*SR1560 ○ ○ 0 - - N R 0
module
Model code of the 1st right-side module connected to the
*SR1561 ○ ○ 0 - - N R 0
CPU module or the remote module
Model code of the 2nd right-side module connected to the
*SR1562 ○ ○ 0 - - N R 0
Model code of the 3rd right-side module connected to the
*SR1563 ○ ○ 0 - - N R 0
Model code of the 4th right-side module connected to the
*SR1564 ○ ○ 0 - - N R 0
*SR1565 ○ ○ 0 - - N R 0
*SR1566 ○ ○ 0 - - N R 0
*SR1567 ○ ○ 0 - - N R 0
*SR1568 ○ ○ 0 - - N R 0
*SR1569 ○ ○ 0 - - N R 0
*SR1570 ○ ○ 0 - - N R 0
*SR1571 ○ ○ 0 - - N R 0
*SR1572 ○ ○ 0 - - N R 0
*SR1573 ○ ○ 0 - - N R 0
*SR1574 ○ ○ 0 - - N R 0
*SR1575 ○ ○ 0 - - N R 0
2 - 11 3
AS100/200 Series
AS300 Series
Attribute
Latched
OFF STOP RUN
Default
ON RUN STOP
_2 *SR1576
○ ○ 0 - - N R 0
*SR1577 ○ ○ 0 - - N R 0
*SR1578 ○ ○ 0 - - N R 0
*SR1579 ○ ○ 0 - - N R 0
*SR1580 ○ ○ 0 - - N R 0
*SR1581 ○ ○ 0 - - N R 0
*SR1582 ○ ○ 0 - - N R 0
*SR1583 ○ ○ 0 - - N R 0
*SR1584 ○ ○ 0 - - N R 0
*SR1585 ○ ○ 0 - - N R 0
*SR1586 ○ ○ 0 - - N R 0
*SR1587 ○ ○ 0 - - N R 0
*SR1588 ○ ○ 0 - - N R 0
*SR1589 ○ ○ 0 - - N R 0
*SR1590 ○ ○ 0 - - N R 0
*SR1591 ○ ○ 0 - - N R 0
*SR1592 ○ ○ 0 - - N R 0
Note 1: for SR*, refer to SM/SR table for more details
Note 2: the communication card in the table refers to AS-F232, AS-F422 and AS-F485.
2 - 11 4
2.2.15 Special Data Registers Refresh Conditions

Special data
Time to refresh
register
SR0–SR2 Refresh the register when there is a program execution error.
SR4–SR6 Refresh the register when there is a grammar check error
SR8–SR9 Refresh the register when there is a watchdog timer error.
SR23 Refresh the register when there is a watchdog timer error. 2_
Refresh the register when the output is used repeatedly by more than one high-speed output
SR28
instruction.
Refresh the register once when there is an error.
SR32
-1: no error occurred.
The register is refreshed by you. You set the flag SM36 to ON and the system saves the data to the
SR36
memory card. After saving is complete, the system automatically resets it to OFF
SR40–SR161 Refresh the register when there is an error.
After the manufactured PLC leaves the factory, every minute the PLC is supplied with power is
SR162–SR163
counted and the register is refreshed every minute.
SR166–SR171 Register is refreshed by the system.
SR172–SR175 Register is refreshed by you.
SR176–SR179 Refresh the register according to the settings in HWCONFIG.
SR180 Refresh the register when the PLC is powered on and powered off.
Refresh the register according to the settings in HWCONFIG when the PLC is powered on. You
SR182–SR183
can edit the settings afterwards.
SR185 Refresh the register for the cycle time after a cycle scan whenever a remote module is activated
SR198–SR199 After a cycle scan when the PLC is powered on.
The register is refreshed according to the settings in HWCONFIG when the PLC is powered on.
SR201–SR213
You can edit the settings afterwards.
SR215–SR216 The register is refreshed by the system.
The register is refreshed according to the settings in HWCONFIG when powered on. You can edit
SR217–SR218
the settings afterwards.
SR220–SR226 Refresh the register every scan cycle.
SR227–SR308 Refresh the register when the program is downloaded to the PLC.
SR309–SR390 Refresh the register when the status of the PLC changes.
SR391–SR397 Refresh the register every scan cycle.
SR407 Refresh the register every second.
SR408–SR416 Refresh the register whenever the instruction END is executed.
SR440–SR443 Refresh the register when the PLC is powered on.
SR444–SR451 Refresh the register when the PLC is powered on.
SR453 Refresh the register when there is an error.
Refresh the register whenever the high-speed output instruction is executed and the program is
SR460
scanned. If the instruction is not executed, you can edit the settings.
SR467 Register is refreshed by the system.
When the PLC is supplied with power, the register is refreshed according to the position planning
SR468–SR469
table. You can edit the settings afterwards.
SR472 Register is refreshed you.
2 - 11 5
Special data
Time to refresh
register
SR474
SR480
_2 SR482–SR486 Register is refreshed by you.
Refresh the register when the PLC is powered on according to the position planning table. You can
SR488–SR489
edit the settings afterwards.
SR492 Register is refreshed by you.
SR494
SR500
SR508–SR509
SR514
SR520
SR528–SR529
SR534
scanned. If the instruction is not executed, you can edit the setting.
SR536–SR537 Register is refreshed by a user.
SR540
SR542–SR546 Register is refreshed by a user.
Refresh the register when the PLC is supplied with power according to the position planning table.
SR548–SR549
You can edit the settings afterwards
SR554
2 - 11 6
Special data
Time to refresh
register
SR560
2_
SR568–SR569
SR574
Refresh the register according to the settings in HWCONFIG when the PLC is powered on. You
SR580–SR603
can edit the settings afterwards.
SR610–SR621 Refresh the register whenever the output instruction is executed.
Refresh the register whenever the EIX or DIX instruction is executed.
SR623–SR634 ON: interrupt is enabled
OFF: interrupt is disabled
SR751-SR768 Register is refreshed by you.
SR820 Refresh the register according to the settings in CANopen Builder.
SR821 Refresh the register when the firmware is updated.
SR822 Refresh the register according to the settings in HWCONFIG.
1. Register is refreshed by you.
SR1000–SR1006
2. Register is refreshed after power-on or after HWCONFIG is downloaded.
1. Refresh the register when a connection is established.
SR1020–SR1107
2. Refresh the register every scan cycle.
SR1116–SR1117 Refresh the register when the program is downloaded to the PLC.
SR1120–SR1183 Refresh the register when the communication is complete.
SR1312-SR1315 Refresh the register during communication
2 - 11 7
Special data
Time to refresh
register
Refresh the register when the parameter is downloaded to the PLC, or when the PLC is supplied
SR1318–SR1320
with power.
SR1335–SR1336 Refresh the register every scan cycle after the function of data exchange is enabled.
_2
SR1375–SR1376 Refresh the register every scan cycle after the function of data exchange is enabled.
SR1435–SR1436 Refresh the register during communication
SR1440–SR1471 Refresh the register when error occurs during communication
SR1475–SR1476 Refresh the register during communication
SR1480–SR1511 Refresh the register when error occurs during communication
SR1520–SR1535 Refresh the register after the communidation through AS-FEN02 is complete.
Register is refreshed by the system when when the system is supplied with power, disconnect from
SR1559–SR1592
the remote module or reestablish the remote module connection.

Registers
1. Scan timeout timer
 SM8/SR8
When a scan timeout occurs during the execution of the program, the error LED on the PLC changes to
continuous ON, and SM8 changes to ON.
SR8 contains the step address at which the watchdog timer changed to ON.
2. Clearing the warning light
 SM22
Setting SM22 to ON clears the error log and the warning light.
3. CPU modue and AD/DA Funciton Card

 Analog Input
AS-F2AD (applicable for AS300 Series PLC)

Item Voltag Input Current Input
Analog Signal Input DC 0–10 V DC 4–20 mA
Resolution 12-bit 11-bit
Digital Conversion Range 0 - 4000 0 - 2000
SR168 (Channel 1 of AS-F2AD card 1)
SR Number
2 - 11 8
AS-F2DA (applicable for AS300 Series PLC)

Item Voltag Output Current Output
Analog Signal Output DC 0–10 V DC 4–20 mA
2_
SR Number
AS218 built-in AD function

Analog Signal Output DC -10V ~ +10V DC -20mA ~ 20mA DC 4mA ~ 20mA*1
Resolution 12-bit 11-bit 11-bit
Digital Conversion Range -2000 ~ 2000 -1000 ~ 1000 0 ~ 1000
SR168 (CH1)
SR Number
SR169 (CH2)
*1: This is only availe for AS218 with FW V1.06.20 and ISPSoft V3.08 or later.
 Analog-input error codes in SM27/SR27
Error code Description Solution

The value to be converted from the built-in AD input channel 1 or AS-
16#0040 Check the actual input signal
F2AD (function card 1) exceeds the allowable range.
The value to be converted from the built-in AD input channel 2 or AS-
F2AD (function card 1) exceeds the allowable range.
The value to be converted from the input channel 1 of AS-F2AD (function
card 2) exceeds the allowable range.
The value to be converted from the input channel 2 of AS-F2AD (function
card 2) exceeds the allowable range.
The connection to current input 4mA~20mA mode from the built-in AD
16#0044 Check the connection
input channel 1 or AS-F2AD (function card 1) is losing.
The connection to current input 4mA~20mA mode from the built-in AD
input channel 2 or AS-F2AD (function card 1) is losing.
The connection to current input 4mA~20mA mode from the input channel
1 of AS-F2AD (function card 2) is losing.
The connection to current input 4mA~20mA mode from the input channel
2 of AS-F2AD (function card 2) is losing.
 Analog Output

Analog Signal Input DC 0–10 V DC 4–20 mA
2 - 11 9

SR172 (Channel 1 of AS-F2DA card 1)
SR Number
_2
AS218 built-in DA function
Item Voltag Output Current Output
Analog Signal Output DC -10V ~ +10V DC -0mA ~ 20mA
Digital Conversion Range -2000 ~ 2000 0 ~ 4000
SR172 (CH1)
SR Number
SR173 (CH2)
4. The real-time clock

 SM220, SR220–SR226, and SR391–SR397
SM220: Calibrate the real-time clock within ±30 seconds
When SM220 changes from OFF to ON, the system calibrates the real-time clock.
If the second value in the real-time clock is in the range 0–29, the minutes value is fixed, and the seconds value
is cleared to zero.
If the value of the second in the real-time clock is in the range 30–59, the minutes value increases by one, and
the seconds value is cleared to zero.
This table lists the corresponding functions and values of SR220–SR226 and SR391–SR397.
Device
Binary-coded Decimal Function Value
decimal system system
SR220 SR391 Year 00–99 (A.D.)
SR221 SR392 Month 1–12
SR222 SR393 Day 1–31
SR223 SR394 Hour 0–23
SR224 SR395 Minute 0–59
SR225 SR396 Second 0–59
SR226 SR397 Week 1–7
SR391–SR397 correspond to SR220–SR226. The difference between SR220–SR226 and SR391–SR397 is
that the former uses the binary-coded decimal while the latter uses the decimal system. For example, December
is represented as 12 in SR392 while it is represented as 1100 in the binary-coded decimal. Refer to Chapter 6
for more information on the real-time clock.
2-120
5. Communication functions
 SM96–SM107, SM209–SM212, SR201–SR202, and SR209–SR216
SR215 and SR216 record the communication port protocol on the PLC. The following table lists the functions
represented by the interface codes.
Code 0 1 2 3 4 5 6
2_
Function No card RS232 RS422 RS485 F2AD F2DA FCOPM
The FCOPM function card only is only supported as Function Card 2.
When the communication port protocol for the PLC is RS485, RS232, or RS422, then SR209 records the
communication format of the COM1 port on the PLC, and SR212 records the communication format of the
COM2 port on the PLC. The following table lists the settings for the communication protocols. Refer to Chapter
6 for more information on the communication instructions.
b0 Data length 7 (value=0) 8 (value=1)

00 ： None
b1
Parity bits 01 ： Odd parity bits
b2
10 ： Even parity bits
b3 Stop bits 1 bit (value=0) 2 bits (value=1)
b4 0001 (H 1) ： 4800
b5
0010 (H 2) ： 9600
b6
b7 0011 (H 3) ： 19200
0100 (H 4) ： 38400
0101 (H 5) ： 57600
0110 (H 6) ： 115200
0111 (H 7) ： 230400
1000 (H 8) ： 500000
1001 (H 9) ： 921000
1010 (16#A) ： Undefined
1011 (16#B) ： Undefined
1100 (16#C) ： Undefined
1101 (16#D) ： Undefined
1110 (16#E) ： Undefined
1111 (16#F) ： User-defined*1

b8-b15 Undefined (reserved)
*1: Refer to the HWCONFIG settings in ISPSoft for the user-defined baudrate.
*2: Refer to section 6.19.3 for the use of communication flags and registers.
2-121
6. Clearing the device contents
 SM203/SM204/SM205
Device number Device which is cleared

The non-latched areas in the input relays, the output relays, the stepping relays, and
the auxiliary relays are cleared.
SM203/SM204
The non-latched areas in the timers, the counters, and the 32-bit counters are
_2 All non-latched areas are
cleared.
cleared.
The non-latched areas in the data registers and the index registers are cleared.
The watchdog timer does not act during this period of time.
The latched areas in the timers, counters, and 32-bit counters are cleared.
SM205 The latched auxiliary relays are cleared.
All latched areas are cleared. The latched data registers are cleared.
The watchdog timer does not act during this period of time.
Refer to Section 2.1.4 for more information on the latched areas in the device range.
7. PLC error log

 SR40-SR161
SR40: The maximum number of error logs stored in SR40 is 20. If the number of the error logs exceeds the
maximum number 20, only 20 of them will be stored. Each error log occupies 6 registers.
SR41: The error log pointer points to the latest error log. When an error occurs, the value of the error log pointer
increases by one. The range of pointer values is 0–19. For example, the error log pointer points to the fourth error
log when the value in SR41 is 3. If the value in SR41 is 20, that means the number of error logs exceeds 20 and is
now in cycle.
SR42~SR161: The time of the error and the position where the error occurs are recorded in SR42–SR161. The lsot
column records the CPU (0) and the remote module number (1~15). The following table lists the corresponding
functions of these data registers.
Module Error Time when the error occurs

Number Slot
ID code Year Month Day Hour Minute Second
SR42 SR45 High SR45 Low SR46 High SR46 Low SR47 High SR47 Low
1 SR43 SR44
Low byte byte byte byte byte byte byte
2 SR49 SR50
3 SR55 SR56
4 SR61 SR62
5 SR67 SR68
6 SR73 SR74
7 SR79 SR80
8 SR85 SR86
9 SR91 SR92
2-122
Module Error Time when the error occurs

Number Slot
ID code Year Month Day Hour Minute Second
10 SR97 SR98
SR102 SR105 SR105 SR106 High SR106 Low SR107 High SR107 Low
11 SR103 SR104
Low byte High byte Low byte byte byte byte byte
12
SR108
SR109 SR110
SR111 High SR111 Low SR112 High SR112 Low SR113 High SR113 Low 2_
SR114 SR117 High SR117 SR118 High SR118 Low SR119 High SR119 Low
13 SR115 SR116
Low byte byte Low byte byte byte byte byte
14 SR121 SR122
15 SR127 SR128
16 SR133 SR134
17 SR139 SR140
18 SR145 SR146
19 SR151 SR152
20 SR157 SR158
8. PLC download log
 SR227-SR308
SR227: The maximum number of download logs which are stored in SR227 is 20. Every download log occupies 4
registers. The download actions which are recorded are numbered, as shown in the following table.
Download action Number

Downloading the program 1
Downloading the PLC setting 2
Downloading the module table 3
SR228: The download log pointer points to the latest download log. When a download action is executed, the value
of the download log pointer increases by one. The range of pointer values is 0–19. For example, the
download log pointer points to the fourth download log when the value in SR228 is 3.
The time of the downloading and the action numbers are recorded in SR229–SR30. The following table lists the
corresponding functions of these data registers.
Action *Time when the download occurs

Number
number Year Month Day Hour Minute Second
SR230 SR230 SR231 SR231 SR232 SR232
1 SR229
High byte Low byte High byte Low byte High byte Low byte
SR234 SR234 SR235 SR235 SR236 SR236
2 SR233
2-123
Action *Time when the download occurs

Number
SR238 SR238 SR239 SR239 SR240 SR240
3 SR237
SR242 SR242 SR243 SR243 SR244 SR244
4 SR241
_2 5 SR245
SR246 SR246 SR247 SR247 SR248 SR248
SR250 SR250 SR251 SR251 SR252 SR252
6 SR249
SR254 SR254 SR255 SR255 SR256 SR256
7 SR253
SR258 SR258 SR259 SR259 SR260 SR260
8 SR257
SR262 SR262 SR263 SR263 SR264 SR264
9 SR261
SR266 SR266 SR267 SR267 SR268 SR268
10 SR265
SR270 SR270 SR271 SR271 SR272 SR272
11 SR269
SR274 SR274 SR275 SR275 SR276 SR276
12 SR273
SR278 SR278 SR279 SR279 SR280 SR280
13 SR277
SR282 SR282 SR283 SR283 SR284 SR284
14 SR281
SR286 SR286 SR287 SR287 SR288 SR288
15 SR285
SR290 SR290 SR291 SR291 SR292 SR292
16 SR289
SR294 SR294 SR295 SR295 SR296 SR296
17 SR293
SR298 SR298 SR299 SR299 SR300 SR300
18 SR297
SR302 SR302 SR303 SR303 SR304 SR304
19 SR301
SR306 SR306 SR307 SR307 SR308 SR308
20 SR305
* The format for the download action time: the data is stored as a binary-coded decimal. The following table lists the
range of values.
Function Value
Year 00–99 (A.D.)
Month 01–12
Day 01–31
Hour 00–23
Minute 00–59
Second 00–59
2-124
9. The PLC status change log
 SR309–SR390
SR309: The maximum number of PLC status change logs stored in SR309 is 20. Each PLC status change log
occupies 4 registers. The recorded PLC status change actions are numbered, as shown in the following
table.
PLC status change Number

2_
PLC powered on. 1
PLC disconnected. 2
PLC starts to run. 3
PLC stops. 4
Default setting in the PLC 5
SR310: The PLC status change log pointer points to the latest PLC status change log. When the PLC status
changes, the value of the PLC status change log pointer increases by one. The range of pointer values is
0–19. For example, PLC status change log pointer points to the fourth PLC status change log when the
value in SR310 is 3.
The time when the PLC status change actions occur is recorded in SR311–SR390. The flowing table lists the
corresponding functions of these data registers.
Action *Time when the PLC status change occurs

Number
SR312 SR312 SR313 SR313 SR314 SR314
1 SR311
SR316 SR316 SR317 SR317 SR318 SR318
2 SR315
SR320 SR320 SR321 SR321 SR322 SR322
3 SR319
SR324 SR324 SR325 SR325 SR326 SR326
4 SR323
SR328 SR328 SR329 SR329 SR330 SR330
5 SR327
SR332 SR332 SR333 SR333 SR334 SR334
6 SR331
SR336 SR336 SR337 SR337 SR338 SR338
7 SR335
SR340 SR340 SR341 SR341 SR342 SR342
8 SR339
SR344 SR344 SR345 SR345 SR346 SR346
9 SR343
SR348 SR348 SR349 SR349 SR350 SR350
10 SR347
SR352 SR352 SR353 SR353 SR354 SR354
11 SR351
12 SR355 SR356 SR356 SR357 SR357 SR358 SR358
2-125
Action *Time when the PLC status change occurs

Number
SR360 SR360 SR361 SR361 SR362 SR362
13 SR359
SR364 SR364 SR365 SR365 SR366 SR366
14 SR363
_2 High byte Low byte High byte Low byte High byte Low byte
SR368 SR368 SR369 SR369 SR370 SR370
15 SR367
SR372 SR372 SR373 SR373 SR374 SR374
16 SR371
SR376 SR376 SR377 SR377 SR378 SR378
17 SR375
SR380 SR380 SR381 SR381 SR382 SR382
18 SR379
SR384 SR384 SR385 SR385 SR386 SR386
19 SR383
SR388 SR388 SR389 SR389 SR390 SR390
20 SR387
*Format for the PLC status change time: the data is stored as a binary-coded decimal. The following table lists the range
of values.
Function Value
Year 00–99 (A.D.)
Month 01–12
Day 01–31
Hour 00–23
Minute 00–59
Second 00–59
10. The PLC operation flag
 SM400-SM403
SM400: The flag is always ON when CPU runs.
SM401: The flag is always OFF when CPU runs.
SM402: The flag is ON only at the first scan. The pulse width equals one scan time. You can use this contact for
the initial value setting.
SM403: The flag is OFF only at the first scan. That is, the negative pulse is generated the moment the PLC runs.
2-126
T he PLC r uns .
SM400
SM401
2_
SM402
SM403
Scan ti me
11. The initial clock pulse
 SM404，SM405，SM406，SM407
The PLC provides seven types of clock pulses. When the PLC is powered on, the seven types of clock pulses act
automatically.
Device Function
10 millisecond clock pulse during which the pulse is ON for 5 milliseconds and then is OFF for 5
SM404
milliseconds
100 millisecond clock pulse during which the pulse is ON for 50 milliseconds and then is OFF for 50
SM405
milliseconds
200 millisecond clock pulse during which the pulse is ON for 100 milliseconds and then is OFF for
SM406
100 milliseconds
One second clock pulse during which the pulse is ON for 500 milliseconds and then is OFF for 500
SM407
milliseconds
The clock pulses are illustrated in the following graphs.

10 ms
SM404 (10 ms) 100 Hz
5 ms
100 ms
SM405 (100 ms) 10 Hz
50 ms
200 ms
SM406 (200 ms) 5 Hz
100 ms
1 sec
SM407 (1 sec) 1 Hz
500 ms
2-127
12. The flags related to the memory card
 SM36, SM450-SM453, SM456-SR36, SR453, SR902
You use the memory card to back up the data in the PLC. Refer to Chapter 6 for instructions concerning the
memory card.
Device Function
_2
SM36 Enable saving data to the memory card. When ON, the PLC runs according to the value in the SR36.
Memory card is present.
SM450 ON: memory card is present.
OFF: memory card is not present.
SM451 Memory card is write-protected.
Data in the memory card is being accessed.
SM452 ON: data in the memory card is being accessed.
OFF: data in the memory card is not accessed.
Error during the operation of the memory card.
SM453 ON: error occurred.
OFF: no error.
Execution of data logger and the memory card.
SM456
ON: execution by the values in SR902.
When an error occurs in the memory card, the error codes are stored here.
A. 16#005D: no memory card installed
B. 16#005E: an error occurs when the memeory card is initialized
C. 16#005F: the path is incorrect or the file does not exist
D. 16#0060: cannot create the default folder
E. 16#0061: the memory space is insufficient
F. 16#0062: the memory card is write protected
SR453 G. 16#0063: an error occurs when the data is written into the file
H. 16#0064: the data cannot be read from the memeory card
I. 16#0065: the file is a read-only file
J. 16#0066: when restoring the memory card PLC is in RUN status
K. 16#0067: when restoring the memory card PLC ID is not matched when restoring the memory card
L. 16#0068: when restoring the memory card the password is not matched
M. 16#0069: when restoring the memory card, the file path and the file name contain the CPU module
name, but it is not matched with the actual CPU module
The code for the executions of data logger and the memory card (works with SM456); for example,
SR902
H5AA5: write the sampling data from the data logger into the memory card.
Use the following function codes to backup or restore data. Enable SM36 for the function codes to
work.
A. K1122 (backup) #1, it indicates backing up the PLC programs to the memory card. (PLC ID and
password are included) Execute this backup when the PLC is in the RUN/Stop status.
Default backup file name: SDCard\PLC CARD\AS300\SysDup\user_program.dup
B. K2211 (restore) #2, it indicates restoring the PLC programs from the memeory card. (PLC ID and
password are included) Execute the restoring when the PLC is in the Stop status.
SR36
Default restore file name: SDCard\PLC CARD\AS300\SysDup\user_program.dup
C. K3344 (backup) #1, it indicates backing up the latched values (D, S, M, C, HC) and the latched
range to the memory card. Execute this backup when the PLC is in the RUN/Stop status.
Default backup file name: SDCard\PLC CARD\AS300\SysDup\retained_data.dup
D. K4433 (restore) #2, it indicates resoring the latched values (D, S, M, C, HC) and the latched range
from the memory card. Execute the restoring when the PLC is in the Stop status.
Default restore file name: SDCard\PLC CARD\AS300\SysDup\retained_data.dup
2-128
Device Function
E. K5566 (backup) #1, it indicates backing up the PLC programs and parameters to the memory card.
(the status and values of retainable devices are NOT included). Execute this backup when the PLC
is in the Stop status.
F. K5577 (backup) #1, it indicates backing up the PLC programs and parameters to the memory card.
(the status and values of retainable devices are included). Execute this backup when the PLC is in
the Stop status.
*E & F functions are the same as the backup function in ISPSoft Card Utility. 2_
Default file name: SDCard\PLC CARD\AS300\SysDup\AS300_save_backup.dup
G. K6755 (restore) #2, it indicates restoring all PLC data from the memeory card (backup files from the
function code E or F). Execute the restoring when the PLC is in the Stop status.
Default file name: SDCard\PLC CARD\AS300\SysDup\AS300_save_backup.dup
Note: if you need to restore from POWER-ON, you need to modify the backup file name and save
the file to SDCard\PLC CARD\AS300\SysDup\AS300_BACKUP.dup before performing restoring
from POWER-ON.
H. K5588 (backup) #1, it indicates backing up all FR file registers from the PLC to the memory card.
Execute this backup when the PLC is in the Stop status.
Default file name: SDCard\PLC CARD\AS300\SysDup\AS300_FR_backup.dup
I. K8855 (restore) #2, it indicates restoring all FR file registers from the memory card to the PLC.
Execute the restoring when the PLC is in the Stop status. The file name should be the same as the
file name in H shows.
(Default file name: SDCard\PLC CARD\AS300\SysDup\AS300_FR_backup.dup)
#1: While backing up, if there is a file with the same file name, the system overwrites the existing file.
#2: While restoring, if the file path and the file name are not identical to the backup file, the system does not excute the
restoring.
NOTE 1: The default file names shown above use AS300 as example. If the PLC you are using is NOT AS300, you can
modify the file name. If the backup file name is not correct, the system does not execute the restoring and
sends out error codes.
NOTE 2: The function codes A, B, C and D shown in SR36 are available for firmware V1.04.30 or later. The function
codes E, F and G in SR36 are available for firmware V1.04.90 or later. The function codes H and I in SR36 are
available for firmware V1.05.30 or later.
NOTE 3: The definitaitons of the abovementioned PLC program, parameters and retainable devices:
The PLC program includes PLC programming execution codes, programming codes, project password and
PLC ID.
The parameters include HWCONFIG configurations, data mapping table and position planning table.
The latched area means parameters and all the values set in this area are retainable.
 While restoring the PLC program from the memeory card, the system verifies the backup file, PLC ID and
password.
 PLC ID check: if the backup file is set with PLC ID, it prevents restoring the PLC program to the wrong PLC.
CPU module with PLC ID CPU module without PLC ID

PLC ID matched: checking the
Backup file with PLC ID password Not restoring
PLC ID not matched: not restoring
Backup file without PLC ID Not restoring Checking the password
 Password check: if the backup file is set with password, it ensures the security of the PLC program and
prevents restoring the PLC program to the wrong PLC.
2-129
CPU module with password CPU module without password

Password matched: restoring
Restoring and you can also set the
Backup file with password Password not matched: not
CPU module with password
restoring
Backup file without password Not restoring Restoring
_2  SR36 only stores 2 logs：
A. The number 1234 means the PLC stores the error log (SR40–SR161) in the memory card.
B. The number 3456 means the PLC stores the error log (SR40–SR161) and the PLC state changing log (SR309–
SR390) in the memory card.
13. The high-speed output instruction is being executed. The output immediately stops when the instruction is
disabled or stops.
 SM587: while using the position planning table to control the output, the axis should refer to the following flags
for the action to stop. This function is available for firmware V.1.06.00 or later.
 SM476, SM477, SM496, SM497, SM516, SM517, SM536, SM537, SM556, SM557, SM576, SM577:
OFF (default): deceleration stop
ON: immediate stop
 SM463, SM474, SM483, SM494, SM503, SM514, SM523, SM534, SM543, SM554, SM563, SM574：use these
flags to pause output.
When the flag changes from OFF to ON, it means stop the output. This works with these flags; refer to the
section above for more actions on stop.
When the flag changes from ON to OFF, it means execute the rest of the outputs.
 The flag for position output axis 1-6 (even number high speed pulse output points) in ramp up / ramp down area
is available for firmware V1.06.00 or later.
 SM586
OFF (default): use high-intensity 250 steps to switch to different speeds in the ramp up/ramp down area and the
error rate of switching time is about 10%.
ON：use high-intensity 25 steps to switch to different speeds in the ramp up/ramp down area and the error rate of
switching time is about 1%.
14. Position control output limit in ISPSoft
 SR580-SR603
Positive output limit: set the limit in ISPSoft. When the output position is greater than the positive limit, the output
stops immediately.
Negative output limit: set the limit in ISPSoft. When the output position is smaller than the negative limit, the output
stops immediately.
When the positive and negative output limits are both 0, the function is disabled. This function works with the
output instructions. The system only checks the limit set in ISPSoft when the instruction is executed. Thus the
system does not come to an immediate stop even when it is beyond the output limit. If an immediate stop is
needed, using the external input as the way to check the limit is recommended.
2-130
15. S curve mode
 SR604-SR609, SM468, SM488, SM508, SM528, SM548, SM568
There are 3 S curves, small, medium and large. The range is between 0–2. When the value exceeds the range, the
system treats the value as the minimum 0 or the maximum 2.
The S curve mode works with the flags such as SM468, SM488, SM568. If the flag is ON, the parameters of the S
curve are executed by the output instruction. 2_
16. Backlash compensation function
 SR478, SR479, SR498, SR499, SR518, SR519, SR538, SR539, SR558, SR559, SR578, SR579
For AS series, up to 12 high-speed outputs (Y0.0-Y0.11) can be set. Each output works with a corresponding SR
for users to set the output number for backlash compensations. The setting range is 0-32767. If the setting value is
<= 0, this function is disabled.
 This function is available for firmware version 1.02.30 and later. The output instrucitons that support odd number
axis outputs and are directional output by default are JOG, DZRN, DPLSV, DDRVI, DDRVA, DPPMR, DPPMA,
DCICR, DCICA, DCICCR, DCICCA, DCCMR, DCCMA, DPPGB and TPO. For even number axis outputs, you
can use the following instructions JOG, DPLSV, DDRVI and DDRVA.
17. Flags to show the output number of the current positioning output in the ramp up / ramp down area.
(available for firmware V1.06.00 or later)
 SR652-653 (32-bit value)
The output number in the ramp up area: the accumulated output number counted from the acceleration starting
point to the target speed point (not included).
 SR654-655 (32-bit value)
The output number in the ramp down area: the accumulated output number counted from the target speed point
(not included) to the output stopping point.
18. Flags to show the CAN communication quality (available for firmware V1.06.00 or later)
 SR823
Hardware receiving error counter for CAN communication: when the error number exceeds 127, it indicates the
hardware error occurance is too frequent, you need to check the communication cables or adjust the
transmission speed or modify the sample points manually.
 SR824
Hardware sending error counter for CAN communication: when the error number exceeds 127, it indicates the
hardware error occurance is too frequent, you need to check the communication cables or adjust the
transmission speed or modify the sample points manually.
19. Ethernet IP related flags
 SM1000, SR1000~SR1015, and (SR1536~SR1539 available for firmware V1.06.00 or later)
SM/SR Function Action

ON: the values in SR1000–SR1006 are written into the flash
memory. After writing the values, the PLC resets it to OFF.
NOTE 1: do not set the flag to ON continuously to avoid
SM1000 Ethernet setting flag.
damage to the flash memory.
NOTE 2: the PLC must be in STOP state before writing the
values into the flash memory.
2-131
SM/SR Function Action

SR1000 For example: 192.168.1.5, SR1000 is 16#C0A8 and SR1001
Ethernet IP address (32-bit)
SR1001 is 0105.
SR1002 For example: 255.255.255.0, SR1002 is 16#FFFF, and
Ethernet netmask address (32-bit)
SR1003 SR1003 is FF00
SR1004 For example: 192.168.1.1, SR1004 is 16#C0A8, and
_2 SR1005
Ethernet gateway address (32-bit)
SR1005 is 0101
Unit: second; default: 30 seconds; setting range: 1-32000; if
the setting value exceeds the setting range, when
SR1006 Duration of the TCP connection
When the value exceeds the range, the system treats the
value as the minimum 1 or the maximum 32000.
SR1007 Current Ethernet speed Unit: Mbps
SR1009 Current TCP connection number Number of all the TCP connections
Unit: ms; default: 20 ms; setting range: 0-32000; when the
value exceeds the range, the system treats the value as the
SR1010 Time to restart TCP communication
minimum 0 or the maximum 32000. If the setting value is 0,
it indicates system restarts communication automatically.
SR1011 MODBUS/TCP Server connection number The system is refreshed automatically.
SR1012 MODBUS/TCP Client connection number The system is refreshed automatically.
SR1013 EtherNet/IP Adapter connection number The system is refreshed automatically.
SR1014 EtherNet/IP Scanner connection number The system is refreshed automatically.
Unit: ms; default: 10 ms; setting range: 0-32000; when the
MODBUS/TCP Server packet receiving
SR1015 value exceeds the range, the system treats the value as the
timeout
minimum 0 or the maximum 32000
Current AS-FEN02 TCP connection
SR1536 Number of all AS-FEN02 TCP connections
number
AS-FEN02 MODBUS/TCP Serves
SR1537 The system is refreshed automatically.
connection number
AS-FEN02 MODBUS/TCP Client
connection number
AS-FEN02 EtherNet/IP Adapter connection
number
 SM1090, SM1091, SM1106-SM1109
SM Function Action
SM1090 TCP connection is busy. ON: TCP connection timeout
SM1091 UDP connection is busy. ON: UDP connection timeout
AS-FEN02 Ethernet - Filter Setting When the program is downloaded to the PLC
SM1110
Error
ON: PHY initialization fails.
SM1106 Ethernet connection error
OFF: PHY initialization succeeds.
ON: basic setting error
SM1107 Ethernet basic setting error
OFF: correct basic setting
TCP/UDP socket local port is already
SM1109 ON: the same port in use
used.
For the error codes, the corresponding LED indicators, and other troubleshooting, Refer to Chapter 12 in the AS300
Series Operation Manual.
2-132
20. Email settings
 SM1113, SM1116-SM1155
If the sending an email fails, the flag of the email service error SM1113 is ON.
The following table lists the triggers for sending email and the corresponding flags (SM1116–SM1155).
Item
Trigger 1 Trigger 2 Trigger 3 Trigger 4 2_
Function
SM1116 SM1126 SM1136 SM1146

Email service
ON: enabled, OFF: disabled
SM1117 SM1127 SM1137 SM1147
Email sending
ON: sending email now, OFF: email sent
SM1119 SM1129 SM1139 SM1149
Emails sent successfully
ON: email sent successfully
SM1120 SM1130 SM1140 SM1150

Email sending error 1
The email cannot be sent due to email content error
SM1122 SM1132 SM1142 SM1152

SMTP response timeout
After sending the email, the SMTP server response timeout.
SMTP server response SM1123 SM1133 SM1143 SM1153

error After sending the email, the SMTP server response error.
SM1124 SM1134 SM1144 SM1154

Email sending error 2 of
After sending the email, the size of the attachment exceeds the limit.
SM1125 SM1135 SM1145 SM1155
Email sending Error 3
After sending the email, the attachment is not found, SM1125 is ON.
21. Flags and registers concerning data exchange
 Flags for data exchange through COM1 connections
SM Type Function
SM750 R/W Data exchange through COM1 enabled by ISPSoft.
SM752–SM783 R/W Connection 1–32 through COM1 for data exchange started.
SM784–SM815 R Data received through COM 1 connection 1–32 for data exchange.
SM816–SM847 R Error in the COM1 connection 1–32 for data exchange.
 Flags for data exchange through COM2 connections
SM Type Function
SM862 R/W Data exchange through COM2 enabled by ISPSoft.
SM864–SM895 R/W Connection 1–32 through COM2 for data exchange started.
SM896–SM927 R Data received through COM2 connection 1–32 for data exchange.
SM928–SM959 R Error in the COM2 connection 1–32 for data exchange
2-133
 Registers for data exchange through COM1 and COM2 connections
SR Function
SR1335 Actual cycle time of connection 1–32 for data exchange through COM1
Number of the connection that is currently performing a cyclical data
SR1336
exchange through COM1
SR1340–SR1371 Error code for data exchange through the COM1 connection 1–32
_2 SR1375 Actual cycle time of connection 1–32 for data exchange through COM2
Number of connection that is currently performing a cyclical data exchange
SR1376
through COM2
SR1380–SR1411 Error code for data exchange through the COM2 connection 1–32
The error codes 1–7 are the standard response error codes of the Modbus protocol. Error code 9 means timeout.
 Flags for data exchange through Funciton Card 1 and Funciton Card 2
SM Type Function Card 1
SM1710 R/W Data exchange through Function Card 1 enabled by ISPSoft
SM1712 ~ SM1743 R/W Connection 1-32 for data exchange through Function Card 1 started
SM1744 ~ SM1775 R Successful data exchange connection 1-32 through Function Card 1
SM1776 ~ SM1807 R Error in data exchange connection 1-32 through Function Card 1
SM Type Function Card 2
SM1822 R/W Data exchange through Function Card 1 enabled by ISPSoft
SM1824 ~ SM1855 R/W Connection 1-32 for data exchange through Function Card 1 started
SM1856 ~ SM1887 R Successful data exchange connection 1-32 through Function Card 1
SM1888 ~ SM1919 R Error in data exchange connection 1-32 through Function Card 1
 Registers for data exchange through Funciton Card 1 and Funciton Card 2
SR Function
SR1435 Actual cycle time for data exchange through Function Card 1
SR1436
exchange through Function Card 1
Error in data exchange connection 1-32 through Function Card 1
SR1440 ~ SR1471 Error codes 1-7 is related to MODBUS issues; refer to manual from the slaves
for more information. Error code 9 indicates communication timeout.
SR1475 Actual cycle time for data exchange through Function Card 2
SR1476
exchange through Function Card 2
Error in data exchange connection 1-32 through Function Card 2
SR1480 ~ SR1511 Error codes 1-7 is related to MODBUS issues; refer to manual from the slaves
for more information. Error code 9 indicates communication timeout.
2-134
 Flags for data exchange through Ethernet connections
SM Type Function
SM1167 R/W Data exchange through Ethernet port enabled by ISPSoft.
SM1168–SM1199 R/W Connection 1–32 through Ethernet port for data exchange started.
SM1200–SM1231 R Data received through Ethernet port connection 1–32 for data exchange.
SM1232–SM1263 R Error in the Ethernet port connection 1–32 for data exchange
2_
 Registers for data exchange through Ethernet connections
SR Function
SR1120–SR1151 Actual connection time for data exchange through the Ethernet connection 1–32
SR1152–SR1183 The error code for data exchange through the Ethernet connection 1–32
 Flags for data exchange through Ethernet connection in AS-FEN02 (available for firmware V1.06.00 or later)
SM Type Function
SM1006 R/W Data exchange through AS-FEN02 enabled by ISPSoft.
SM1008 ~ SM1015 R/W Connection 1–8 through AS-FEN02 for data exchange started.
SM1016 ~ SM1023 R Successful data exchange connection 1-8 through AS-FEN02
SM1024 ~ SM1031 R Error in the AS-FEN02 connection 1–8 for data exchange
 Registers for data exchange through Ethernet connection in AS-FEN02 (available for firmware V1.06.00 or
later)
SR Funciton
SR1520 ~ SR1527 The actual communication time for data exchange connection 1-8 through AS-FEN02
SR1528 ~ SR1535 Error in data exchange connection 1-8 through AS-FEN02
 Error codes for Ethernet connections
Error code Description

Remote module response error
16#00XX
Code 1~7 are standard Modbus TCP protocol error codes
16#F000 Ethernet connection is not established
16#F001 Remote module response timeout
16#F003 TCP connection timeout

16#F007 Response error
16#F009 Connection lost in the remote module
 The list of SM/SR states when connecting to RTU-EN01 throught Ethernet port
SM / SR Description
SM1312 - SM1315 The communication state flags of RTU-EN01 connection ID 1-4
SR1312 - SR1315 The communication state codes of RTU-EN01 connection ID 1-4
SR SM state Description
0 Off Connection closed
1 On Successful connection
2 Off Communiction timeout
3 Off Connection closed by force
4 Off RTU-EN01 response: error in contents
5 Off RTU-EN01 response: error
2-135
6 Off Network not connected or connection failed

RX & RCR Read data RY & RCR Write data
SM state
(input mapping area) (output mapping area)
Off  On Clear to 0 Clear to 0
On  Off No change No change
Note: Before the connection is established, it is suggested NOT to use data (RX/RY/RCR Read/RCR Write) in the
mapping area.
_2
 Ethernet/IP communication flags are available for PLC FW V1.06 or later.
SM Attr. Ethernet/IP Data Exchange Description
SM1375 R/W Data exchange through EtherNet/IP (Scanner) started.
SM1376 - SM1407 R/W Connection 1-32 for data exchange through EtherNet/IP (Scanner) started
SM1408 - SM1439 R Error in data exchange connection 1-32 through EtherNet/IP (Scanner)
SM1440 - SM1447 R Error in I/O connection 1-8 through EtherNet/IP (Adapter)
SM1448 – SM1455*1 R I/O connection 1-8 is established through EtherNet/IP (Adapter)

*1: only available for PLC FW V1.06.50 or later
 Ethernet/IP communication registers are available for PLC FW V1.06 or later.

SR Attr. Ethernet/IP Data Exchange Description
Status code of the connection 1-32 for data exchange through EtherNet/IP
SR1020 - SR1051 R
(Scanner)
 Ethernet/IP communication error codes are listed below. Refer to Chapter 9 in AS Series Operation Manual for
more details.
Error Code Description Solution
1. Check if the system has created the I/O
16#0100 I/O connections duplicated connections.
2. Change the connection type to Listen Only.
1. Check the scanner owner.
Scanner ownership of I/O
16#0106 2. Reconfigure the invalid scanner.
connections conflicts
3. Change the connection to multicast.
1. Check the I/O connection status.
16#0110 Incorrect adapter configuration
2. Activate the I/O connections again.
16#0111 Adapter RPI not supported Check the RPI for the adapter.
1. Check if the number of connections exceeds the limit.
16#0113 Insufficient I/O connections 2. Reduce the number of the product
connections.
The connection of non-Listen only is 1. Check if the system has created the I/O connections.
16#0119
not established. 2. Check the scanner I/O connection status.
Check the module number and the product setup file to see if
16#0127 Incorrect adapter input size
they match.
16#0128 Incorrect adapter output size Check the output size in the connection parameters.
Check if the parameters in the Consumed tag are set
16#012D Consumed TAG does not exist.
correctly.
Check if the parameters in the Produced tag are set
16#012E Produced TAG does not exist.
correctly.
No response from the adapter; check if the power and the
16#0204 I/O connection connecting timeout
network connection for the adapter are working properly.
Network bandwidth NOT available 1. Check the I/O connection limit between the scanner and
16#0302
for data the adapter.
2-136
2 . Increase the RPI value or reduce the number of

connections.
Incorrect adapter input/output Check the module number and the product setup file to see if
16#0315
instance they match.
I/O connection communication No response from the adapter; check if the power and the
16#0203
timeout network connection for the adapter are working properly.
22. Flags SM230-SM261 is to activate modules when selecting “Manual + Flags” in “I/O allocation setting when Power 2_
On”.
When selecting “Manual + Flags (only I/O module of CPU module)” in “I/O allocation setting when Power On”, use
flags SM230-SM261 to activate the 1st – 32nd module on the right-side of the CPU module. (available for FW
V1.06.00 or later).
When selecting “Manual + Flags (I/O module of CPU & Remote module)”, use flags SM230-SM261 to activate the
1st – 32nd module on the right-side of the CPU module remotely (available for FW V1.08.50 or later and ISPSoft
V3.12 or later supports this funciton.)
For less module applications, you can use the same PLC program and download the I/O allocation table once for
various I/O applications. Two things to be noted when applying this mode:
A. You need to use a bigger I/O allocation planning beforehand and store this planning in AS series PLC.
B. You can simply use special flags to mark which I/O module will NOT be used to meet the actual I/O module
placement. But you cannot rearrange the original order of the module placement.
Add a new selection “Manual + Flags” for the setting option “I/O module allocation setting when Power ON”. Select
this option, you need to use it with flags SM230-SM261. For less module applications, you can simply use special
flags to mark which I/O module will NOT be used to meet the actual I/O module placement. In this mode, you can
use the same PLC program and download the I/O allocation table once for various I/O applications.
Example:
Step 1: Select “Manual + Flags” for the setting option “I/O module allocation setting when Power ON” in
HWCONFIG.
Step 2: Plan an entire module allocation and download the I/O allocation table to HWCONFIG
Step 3: When 16AP, 04DA, and 08AM are not needed in the application, you can set the flags SM231 (indicating
16AP), SM233 (indicating 04DA) and SM235 (including 08AM) to OFF to meet the actual I/O module placement.
You do not need to change their order number in the PLC program.
2-137
Actual I/O Module Placement

_2
The order numbers, the model names and their corresponding device numbers in the complete I/O allocation list.
Order
0 1 2 3 4 5 6 7
number
Model AS332 16AP 16AP 04AD 04DA 06XA 08AM 08AN
Corresponding device
X1.0/Y1.0 X2.0/Y2.0 D28040 D28060 D28080 X3.0 Y3.0
starts from
The order number and the corresponding device numbers stay the same.
Order
0 1 3 5 7
number
Model AS332 16AP 04AD 06XA 08AN
Corresponding device
X1.0/Y1.0 D28040 D28080 Y3.0
starts from
The order number rule also applies when you use the FROM/TO or other module-related instructions.
23. Number of modules and the device codes

SR Description
Number of the remote modules connected to the CPU module (all right-side modules
SR1559
not included)
SR1560 Number of the right-side modules connected to the CPU module
Model code of the 1st – 32nd right-side module connected to the CPU module or the
SR1561~SR1592
remote module
DIO modules
Model Device code Model Device code Model Device code
AS08AM10N-A 16#0201 AS08AN01T-A 16#0206 AS08AN01P-A 16#0207
AS08AN01R-A 16#0208 AS16AM10N-A 16#0210 AS16AP11T-A 16#0212
AS16AP11P-A 16#0213 AS16AP11R-A 16#0214 AS16AN01T-A 16#0216
AS16AN01P-A 16#0217 AS16AN01R-A 16#0218 AS32AM10N-A 16#0220
AS32AN02T-A 16#0226 AS64AM10N-A 16#0230 AS64AN02T-A 16#0236
AIO modules (temperature, loadcell)
AS04AD-A 16#0301 AS08AD-B 16#0302 AS08AD-C 16#0303
2-138
AS04DA-A 16#0305 AS06XA-A 16#0309 AS04RTD-A 16#0310

AS06RTD-A 16#0311 AS04TC-A 16#0315 AS08TC-A 16#0316
AS02LC-A 16#0320
NIO modules (communication)
AS00SCM-A 16#0401 AS01DNET-A 16#0402
PIO modules (positioning and counter) 2_
AS02PU-A 16#0501 AS04PU-A 16#0502 AS02HC-A 16#0505
Example:
After power-on, the module allocation of the above example is as shown below.
SR1559 = 2; SR1560 = 4
The order number is counted by the right-side modules connected to the CPU module and then counted by the RTU
number.
SR number (order) SR1651 (#1) SR1652 (#2) SR1653 (#3) SR1654 (#4) SR1655 (#5)
Device code 16#0309 16#0311 16#0212 16#0212 16#0301
SR number (order) SR1656 (#6) SR1657 (#7) SR1658 (#8) SR1659 (#9)
Device code 16#0315 16#0302 16#0210 16#0210
If RTU is disconnected, after reconnected, the system refreshes the SR.
SR1559 = 1; SR1560 = 4
2-139
24. Auto-reset flags for pulse output

 While executing the pulse output instructions, to avoid the control over the same pulse output device is
taken repeatedly by different type or diffent triggered output instrucitons. PLC assigns the right to
control the pulse instruction to the first executed instruction till the assigned instruction is completely
stopped. Because of the unique characteristic, PLC scan cannot detect if the pulse instruction is
stopped when you use the pulse output instruction in the ST language, interrupt subroutine or one-time
_2 function block. Therefore, the right to control the pulse instruction is kept and any ongoing instructions
can nether be executed nor outputted normally.
 To free the right to execute other pulse output instructions, you can use the auto-reset flags for the PLC
to check if the output is complete.
Note: you can set the auto-reset flags to ON and once the output is complete, the flag resets to OFF
automatically.
Even number axis for output Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
Auto-reset the right to execute
SM470 SM490 SM510 SM530 SM550 SM570
other output instructions.
Odd number axis for output Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
Auto-reset the right to execute
SM475 SM495 SM515 SM535 SM555 SM575
other output instructions.
 List of pulse output instrucitons:

Even Odd Auto-
Instruciton number number reset Auto-reset timing Remarks
axis axis flag
PWM/DPWM V V  No need to set up the
number of pulses to
JOG/DJOG V V output.
 It is suggested to use
DPLSV V V in applications that the
Once the auto-reset flag is
instruction is stopped
DPPGB V ON, free the right to
Yes and the instruction will
execute other pulse output
not be scanned again.
instructions.
(for example ST
language
CSFO V programming,
interrupts, and one-
time function block).
PLSR V V
PLSY V V  Need to set up the
DDRVI V V number of pulses to
DDRVA V V Once the auto-reset flag is output.
DDRVM V ON, and pulse output is  Directional output
DPPMR V complete or the instrucitons with
DPPMA V Yes positive/negative limit is positive/negative limits
DCICR V reached, free the right to  For more than two
DCICA V execute other pulse output axes, each axis
DCICCR V instruciotns. requires an auto-reset
DCICCA V flag; one axis, one
DCCMR V auto-reset flag.
DCCMA V
DZRN V  Instructions will be
scanned and
N/A
DZRN2 V V monitored; no need for
an auto-reset flag.
2-140
Example 1 (used in function blocks or interrupts)
POU
2_
Function block (FB) or interrupts:
Explanation
1. When M0 is ON, Y0.0 outputs 1000 pulses at 1kHz, and set SM470 on Y0.0.
2. When Y0.0 output is complete, PLC frees the right for the Y0.0 to be ready again.
3. When M0 is from OFF to ON again, Y0.0 output can start again.
Example 2 (used in ST programming language)
Explanation
1. When M0 is ON, Y0.0 outputs 1000 pulses at 1kHz, and set M1 to ON to record Y0.0 is taken.
2. When M0 is OFF, once Y0.0 output is complete, SM461 is ON. IF M1 is ON, it triggers the auto-reset flag of Y0.0
(SM470=ON) and PLC frees the right for the Y0.0 to be ready again.
3. When M0 is from OFF to ON again, Y0.0 output can start again.
2-141
25. Auto-rest flags for Delta CAN communicaiton

 While executing the CAN instructions, to avoid the control over the same ID of Servo/Inverter is taken
repeatedly by different type or diffent triggered CAN instrucitons. PLC assigns the right to control the
pulse instruction to the first executed instruction till the assigned instruction is completely stopped.
Because of the unique characteristic, PLC scan cannot detect if the CAN instruction is stopped when
you use the CAN instruction in the ST language, interrupt subroutine or one-time function block.
_2 Therefore, the right to control the CAN instruction is kept and any ongoing instructions can nether be
executed nor control the servo/inverter normally.
 To free the right to execute other CAN output instructions, you can use the auto-reset flags for the PLC
to check if the communicaton between Delta Servo or Delta Moto is complete.
Note: you can set the auto-reset flags to ON and once the CAN communication is complete, the flag resets
to OFF automatically.
Delta Servo
1 2 3 4 5 6 7 8
Station ID
Auto-reset the
right to execute
SM1581 SM1582 SM1583 SM1584 SM1585 SM1586 SM1587 SM1588
other CAN
instructions.
Delta Moto
21 22 23 24 25 26 27 28
Station ID
Auto-reset the
right to execute
SM1601 SM1602 SM1603 SM1604 SM1605 SM1606 SM1607 SM1608
other CAN
instructions.
 List of CAN communicaiton instrucitons:

Auto-
Delta Delta
Instruciton reset Auto-reset timing Remarks
Servo inverter
flag
INITC V V
ASDON V V
CASD V V
DDRVIC V
Once the auto-reset flag is
DDRVAC V
ON, free the right to
DPLSVC V V Yes
execute other pulse
ZRNC/DZRNC V
output instructions.
RSTD V V
DCSFOC V
DTQC V V
DTQLC V V
ZRNM V
EMER V V
COPRW V V Instructions will be
COPWL/DCOPWL V V scanned and monitored;
N/A
ECAMD V no need for an auto-reset
DECAMS V flag.
ECAMA V
ECAMC V
2-142
Example 1 (used in function blocks)
POU:
2_
FB:
Explanation
1. When M0 is ON, Servo #1 runs to the relative position 10000 PUU at the speed of 100.0 r/min. And set M1 to ON to
record that communication right of Servo#1 is taken.
2. When SM1631 is ON (positioning completed) and M1 is ON, trigger SM1581 to ON to have the PLC free the
communication right for Servo #1.
3. When M0 is from OFF to ON again, Servo #1 is ready to positioning again.
Example 2 (used in ST programming language)
Explanation
1. When M0 is ON, Servo #1 runs to the relative position 10000 PUU at the speed of 100.0 r/min. And set M1 to ON to
record that communication right of Servo#1 is taken.
2. When M0 is OFF, SM1631 ON (positioning completed) and M1 ON, trigger SM1581 to ON to have the PLC free the
communication right for Servo #1.
3. When M0 is from OFF to ON again, Servo #1 is ready to positioning again.
2-143
2.2.17 Index Register (E)

The Index register is a 16-bit data register. It is similar to the General register in that data can be read from it and written
to it; however, it is mainly used as the index register. The range of index registers is E0–E9. Refer to Section 4.4 in the
AS300 Series Programming Manual for more information about using index registers.
_2 2.2.18 File Registers (FR)

 The AS300 Series PLC provides you with File registers for storing larger numbers of parameters.
 You can edit, upload, and download the parameters in the File registers through ISPSoft.
 You can read the values in File registers while operating the PLC. Refer to the MEMW instruction (API 2303) in the
AS300 Series Programming Manual for more information about how to write to the File registers.
2-144
3
Chapter 3 Instruction Tables
Table of Contents
3.1 Types of Instructions......................................................................... 3-2
3.1.2 Applied Instructions ....................................................................... 3-2
3.2 Understanding Instruction Tables ..................................................... 3-3

3.2.2 Applied Instructions (Sorted numerically) ......................................... 3-4
3.2.3 Applied Instructions (Sorted Alphabetically) ...................................... 3-5
3.2.4 Device Tables ................................................................................ 3-6
3.3 Lists of Basic Instructions ................................................................. 3-7
3.4 Lists of Applied Instructions .............................................................. 3-9

3.4.1 Applied Instructions (Sorted numerically by API number) .................... 3-9
3.4.2 Applied Instructions (Sorted Alphabetically) .....................................3-44
3-1
3.1 Types of Instructions

Instructions used in the AS300 Series PLC include basic instructions and applied instructions.
3.1.1 Basic Instructions

Classification Description
Instructions such as loading the contact, connecting the contact in series, and
Contact instructions
connecting the contact in parallel
Output instructions Bit device output; pulse output
Master control Instructions Setting and resetting the master control
_3 Rising-edge/Falling-edge Triggering the instructions that load the contact, connect the contacts in series,
detection contact instructions and connect the contacts in parallel
Rising-edge/Falling-edge
Bit device differential output
differential output instructions
Other instructions Other instructions
3.1.2 Applied Instructions

API Classification Description
0000-0083 Comparison instructions Comparisons such as =, <>, >, >=, <, <=
Using binary numbers or binary-coded decimal numbers to add,
0100-0118 Arithmetic instructions
subtract, multiply, or divide
Converting a binary-coded decimal number into a binary number,
0200-0217 Data conversion instructions
and converting a binary number into a binary-coded decimal number
0300-0310 Data transfer instructions Transfer the specified data
0400-0402 Jump instructions Control jumps to a different part of the program
Program execution
0500-0504 Enabling or disabling the interrupt
instructions
0600-0602 I/O refreshing instructions Refreshing the I/O
Instructions such as those that apply to the counters, the teach
0700-0711 Miscellaneous instructions
mode timers, and the special timers
0800-0817 Logic instructions Logical operations such as logical addition and logical multiplication
0900-0904 Rotation instructions Rotating/Shifting the specified data
1000-1015 Basic instructions Timer instructions and counter instructions
1100-1115 Shift instructions Shifting the specified data
1200-1227 Data processing instructions 16-bit data processing such as decoding and encoding
Structure creation
1300-1302 Nested loops
instructions
Reading the data from a specific module and writing the data into a
1400-1427 Module instructions
specific module
Floating-point number
1500-1517 Floating-point number operations
instructions
1600-1608 Real-time clock instructions Reading and writing, adding, subtracting and comparing the time
1700-1704 Peripheral instructions I/O points connected to the peripheral
1806-1821 Communication instructions Controlling the peripheral though communication
Watchdog timer, program delay timer, pulse width, and index
1900-1906 Other instructions
registers
3-2
C ha pt er 3 I ns tr uc t i o n Tab l es
API Classification Description

Conversion between binary or binary-coded decimal numbers and
String processing ASCII codes; conversion between binary numbers and strings;
2100-2119
instructions conversion between floating-point numbers and strings; string
processing
2200-2212 Ethernet instructions Controlling the Ethernet data exchange
Memory card / File register Reading the data from the memory card / file register and writing the
2300-2304
instructions data to the memory card / file register
2400-2401 Task control instructions Controlling tasks in the program
Sequential function charts
2500-2502 Controlling the SFC instructions
(SFC) instructions
High-speed output
2700-2724
instructions
High-speed output and position control instructions
3_
Delta special CANopen
2800-2818 CANopen communication instructions especially for Delta devices
communication instructions
3.2 Understanding Instruction Tables

This section describes the table format that this chapter and the rest of this manual uses to describe each instruction.
The format is different depending on the type of instruction: Basic or Applied.
3.2.1 Basic Instructions

This section describes the table format that this chapter uses to describe basic instructions in Section 3.3.
Description:
: The instruction name
: The symbol for the instruction in the ladder diagram in ISPSoft
: The function of the instruction
: The operands supported by the instruction
3-3
3.2.2 Applied Instructions (Sorted numerically)

This section describes the table format that this chapter uses to describe applied instructions (sorted by API number) in
Section 3.4.1.
_3
Description:
: The applied instruction number
: The instruction name
: If a 16-bit instruction can be used as a 32-bit instruction, add a D in front of the 16-bit instruction to form the 32-bit
instruction.
:  indicates that you can use the instruction as a pulse instruction, whereas ─ indicates that it cannot be used as a
pulse instruction. For pulse instructions, add a P in back of the instruction.
: The symbol for the instruction in the ladder diagram in ISPSoft
: The function of the instruction
: For single-precision floating-point instructions (32-bit), an F appears in the instruction.
3-4
3.2.3 Applied Instructions (Sorted Alphabetically)

This section describes the table format that this chapter uses to describe applied instructions (sorted alphabetically) in
Section 3.4.2.
3_
Description:
: The initial of the instruction name
: The applied instruction number
～：The instruction names
If the 16-bit instruction can be used as the 32-bit instruction, add a D in front of the 16-bit instruction to form the 32-bit
instruction.
： indicates that you can use the instruction as a pulse instruction, whereas ─ indicates that it cannot be used as a
pulse instruction. For the pulse instruction, add a P at the end of the instruction.
: The function of the instruction
3-5
3.2.4 Device Tables

This section describes the table format used in the rest of this manual to describe each instruction.
_3
Description:
: The applied instruction number
: The instruction name
If the 16-bit instruction can be used as the 32-bit instruction, add a D in front of the 16-bit instruction to form the 32-bit
instruction.
: The operand
: The function of the instructions
: The devices that are supported by the operand
1. The decimal forms are indicated by “K”, but you enter them directly in ISPSoft. For example, enter the decimal
number 30 in ISPSoft.
2. The hexadecimal forms are indicated by 16#. For example, the decimal number 30 is represented by 16#1E in
the hexadecimal system.
3. The floating-point numbers are indicated by “F” or ”DF”, but they are represented by decimal points in ISPSoft.
For example, the floating-point number F500 is represented by 500.0 in ISPSoft.
4. The strings are indicated by “$”, but they are represented by quotes (“ ”) in ISPSoft. For example, the string
1234 is represented by “1234” in ISPSoft.
3-6
5. ○: The hollow circle

Indicates that the device cannot be modified by an index register.
6. ●: The solid circle
Indicates that the device can be modified by an index register.
：The unit of the operand
：The format of the instruction
Indicates whether the instruction can be used as a pulse instruction, a 16-bit instruction, or a 32-bit instruction.
：The symbol for the instruction in the ladder diagram in ISPSoft.
3_
3.3 Lists of Basic Instructions
 Contact instructions
Instruction
Symbol Function Operand
code
LD
Loading contact A/Connecting

AND contact A in series/Connecting DX, X, Y, M, SM, S, T, C, HC, D
contact A in parallel
OR
LDI
Loading contact B/Connecting

ANI contact B in series/Connecting DX, X, Y, M, SM, S, T, C, HC, D
contact B in parallel
ORI
 Output instructions
Instruction Execution
code condition
OUT Driving the coil DY, Y, M, SM, S, T, C, HC, D
Keeping the
SET DY, Y, M, SM, S, T, C, HC, D
device on
 Master control instructions
Instruction
code
MC Setting the master control N
3-7
Instruction
code
MCR Resetting the master control N
 Rising-edge/Falling-edge detection contact instructions
Instruction code Symbol Function Operand Instruction code
LDP
_3
ANDP DX, X, Y, M, SM, S, T, C, HC, D
Starting the rising-
edge
ORP detection/Connecti
ng the rising-edge
detection in
PED series/Connecting
the rising-edge
detection in parallel
APED X, Y,M, SM, S, T, C, HC, D
OPED
LDF
ANDF DX, X, Y, M, SM, S, T, C, HC, D

Starting the falling-
edge
ORF detection/Connecti
ng the falling-edge
detection in
NED series/Connecting
the falling-edge
ANED X, Y,M, SM, S, T, C, HC, D
ONED
3-8
 Rising-edge/Falling-edge differential output instructions
Execution
Instruction code Symbol Function Operand
condition
Rising-edge
PLS Y, M, SM, S
differential output
Falling-edge
PLF Y, M, SM, S
differential output
 Other instructions 3_
Instruction code Symbol Function Operand
Inverting the logical
INV ─
operation result
The circuit is rising edge-
NP ─
triggered.
The circuit is falling edge-
PN ─
triggered.
The circuit is rising edge-
FB_NP Y, M, S, D
triggered.
The circuit is falling edge-
FB_PN Y, M, S, D
triggered.
3.4 Lists of Applied Instructions

3.4.1 Applied Instructions (Sorted Numerically by API number)
 Comparison instructions
Instruction code Pulse

API Symbol Function
16-bit 32-bit Instruction
Comparing values
0000 LD= DLD= ─ ON: S1＝S2
OFF: S1≠S2
Comparing values
0001 LD<> DLD<> ─ ON: S1≠S2
OFF: S1＝S2
Comparing values
0002 LD> DLD> ─ ON: S1＞S2
OFF: S1<=S2
Comparing values
0003 LD>= DLD>= ─ ON: S1>=S2
OFF: S1＜S2
Comparing values
0004 LD< DLD< ─ ON: S1＜S2
OFF: S1>=S2
3-9

API Symbol Function
Comparing values
0005 LD<= DLD<= ─ ON: S1<=S2
OFF: S1＞S2
Comparing values
0006 AND= DAND= ─ ON: S1＝S2
OFF: S1≠S2
Comparing values
0007 AND<> DAND<> ─ ON: S1≠S2
_3 OFF: S1＝S2
Comparing values
0008 AND> DAND> ─ ON: S1＞S2
OFF: S1<=S2
Comparing values
0009 AND>= DAND>= ─ ON: S1>=S2
OFF: S1＜S2
Comparing values
0010 AND< DAND< ─ ON: S1＜S2
OFF: S1>=S2
Comparing values
0011 AND<= DAND<= ─ ON: S1<=S2
OFF: S1＞S2
Comparing values
0012 OR= DOR= ─ ON: S1＝S2
OFF: S1≠S2
Comparing values
0013 OR<> DOR<> ─ ON: S1≠S2
OFF: S1＝S2
Comparing values
0014 OR> DOR> ─ ON: S1＞S2
OFF: S1<=S2
Comparing values
0015 OR>= DOR>= ─ ON: S1>=S2
OFF: S1＜S2
Comparing values
0016 OR< DOR< ─ ON: S1＜S2
OFF: S1>=S2
Comparing values
0017 OR<= DOR<= ─ ON: S1<=S2
OFF: S1＞S2
3-10

API Symbol Function
Comparing floating-point numbers
0018 ─ FLD= ─ ON: S1＝S2
OFF: S1≠S2
0019 ─ FLD<> ─ ON: S11≠S2
OFF: S1＝S2
0020 ─ FLD> ─ ON: S1＞S2
OFF: S1<=S2
3_
0021 ─ FLD>= ─ ON: S1>=S2
OFF: S1＜S2
0022 ─ FLD< ─ ON: S1＜S2
OFF: S1>=S2
0023 ─ FLD<= ─ ON: S1<=S2
OFF: S1＞S2
0024 ─ FAND= ─ ON: S1＝S2
OFF: S1≠S2
0025 ─ FAND<> ─ ON: S1≠S2
OFF: S1＝S2
0026 ─ FAND> ─ ON: S1＞S2
OFF: S1<=S2
0027 ─ FAND>= ─ ON: S1>=S2
OFF: S1＜S2
0028 ─ FAND< ─ ON: S1＜S2
OFF: S1>=S2
0029 ─ FAND<= ─ ON: S1<=S2
OFF: S1＞S2
0030 ─ FOR= ─ ON: S1＝S2
OFF: S1≠S2
3 - 11

API Symbol Function
0031 ─ FOR<> ─ ON: S1≠S2
OFF: S1＝S2
0032 ─ FOR> ─ ON: S1＞S2
OFF: S1<=S2
0033 ─ FOR>= ─ ON: S1>=S2
_3 OFF: S1＜S2
0034 ─ FOR< ─ ON: S1＜S2
OFF: S1>=S2
0035 ─ FOR<= ─ ON: S1<=S2
OFF: S1＞S2
Comparing strings
0036 LD$= ─ ─ ON: S1＝S2
ON: S1≠S2
Comparing strings
0037 LD$<> ─ ─ ON: S1≠S2
OFF: S1＝S2
Comparing strings
0042 AND$= ─ ─ ON: S1＝S2
OFF S1≠S2
Comparing strings
0043 AND$<> ─ ─ ON: S1≠S2
OFF: S1＝S2
Comparing strings
0048 OR$= ─ ─ ON: S1＝S2
OFF: S1≠S2
Comparing strings
0049 OR$<> ─ ─ ON: S1≠S2
OFF: S1＝S2
0054 CMP DCMP  Comparing values
3-12

API Symbol Function
0055 ZCP DZCP  Zone comparison
0056 ─ FCMP  Comparing floating-point numbers
3_
0057 ─ FZCP  Floating-point zone comparison
0058 MCMP ─  Matrix comparison
Comparing tables
0059 CMPT= ─ 
ON: =
Comparing tables
0060 CMPT<> ─ 
ON: ≠
Comparing tables
0061 CMPT> ─ 
ON: >
Comparing tables
0062 CMPT>= ─ 
ON: >=
Comparing tables
0063 CMPT< ─ 
ON: <
Comparing tables
0064 CMPT<= ─ 
ON: <=
Checking the address of the contact type of

0065 CHKADR ─ ─
a pointer register
Comparing the absolute result of the contact

type
0066 LDZ= DLDZ= ─
ON: | S1- S2|＝| S3|
OFF: | S1- S2| ≠ | S3|
3-13

API Symbol Function
type
0067 LDZ<> DLDZ<> ─ ON: | S1- S2|≠| S3|
OFF: | S1- S2|＝| S3|
type
0068 LDZ> DLDZ> ─ ON: | S1- S2|＞| S3|
OFF: | S1- S2| <= | S3|
_3 type
0069 LDZ>= DLDZ>= ─ ON: | S1- S2|>=| S3|
OFF: | S1- S2|＜| S3|
type
0070 LDZ< DLDZ< ─ ON: | S1- S2|＜| S3|
OFF: | S1- S2|>= | S3|
type
0071 LDZ<= DLDZ<= ─ ON:| S1- S2|<=| S3|
OFF: | S1- S2|＞| S3|
type
0072 ANDZ= DANDZ= ─
ON: | S1- S2|＝| S3|
OFF: | S1- S2| ≠ | S3|
type
0073 ANDZ<> DANDZ<> ─ ON: | S1- S2|≠| S3|
OFF: | S1- S2|＝| S3|
type
0074 ANDZ> DANDZ> ─ ON: | S1- S2|＞| S3|
OFF: | S1- S2| <= | S3|
type
0075 ANDZ>= DANDZ>= ─ ON: | S1- S2|>=| S3|
OFF: | S1- S2|＜| S3|
type
0076 ANDZ< DANDZ< ─ ON: | S1- S2|＜| S3|
OFF: | S1- S2|>= | S3|
3-14

API Symbol Function
type
0077 ANDZ<= DANDZ<= ─ ON: | S1- S2|<=| S3|
OFF: | S1- S2|＞| S3|
type
0078 ORZ= DORZ= ─
ON: | S1- S2|＝| S3|
OFF: | S1- S2| ≠ | S3|
type 3_
0079 ORZ<> DORZ<> ─ ON: | S1- S2| ≠ | S3|
OFF: | S1- S2|＝| S3|
type
0080 ORZ> DORZ> ─ ON: | S1- S2|＞| S3|
OFF: | S1- S2| <= | S3|
type
0081 ORZ>= DORZ>= ─ ON: | S1- S2| >= | S3|
OFF: | S1- S2|＜| S3|
type
0082 ORZ< DORZ< ─ ON: | S1- S2|＜| S3|
OFF: | S1- S2| >= | S3|
type
0083 ORZ<= DORZ<= ─ ON: | S1- S2| <= | S3|
OFF: | S1- S2|＞| S3|
 Arithmetic instructions

API Symbol Function
16-bit 32-bit instruction
Adding binary numbers

0100 + D+ 
S1+S2=D
Subtracting binary numbers

0101 - D- 
S1-S2=D
3-15

API Symbol Function
Multiplying binary numbers

0102 * D* 
S1*S2=D
Dividing binary numbers

0103 / D/ 
S1/S2=D
_3
Adding floating-point numbers

0104 ─ F+ 
S1+S2=D
Subtracting floating-point numbers

0105 ─ F- 
S1-S2=D
Multiplying floating-point numbers

0106 ─ F* 
S1*S2=D
Dividing floating-point numbers

0107 ─ F/ 
S1/S2=D
0112 BK+ DBK+  Adding binary numbers in blocks
0113 BK- DBK-  Subtracting binary numbers in blocks
0114 $+ ─  Linking strings
0115 INC DINC  Adding one to a binary number
3-16

API Symbol Function
0116 DEC DDEC  Subtracting one from a binary number
Multiplying binary numbers for 16-bit

0117 MUL16 MUL32 
multiplying binary numbers for 32-bit
3_
Dividing binary numbers for 16-bit
0118 DIV16 DIV32 
Dividing binary numbers for 32-bit
 Data conversion instructions

API Symbol Function
Converting a binary number into the binary-

0200 BCD DBCD 
coded decimal number
Converting a binary-coded decimal number

0201 BIN DBIN 
into a binary number
Converting a binary integer into a binary

0202 FLT DFLT 
floating-point number
Converting a 32-bit floating-point number into

0204 INT DINT 
a binary integer
0206 MMOV ─  Converting a 16-bit value into a 32-bit value
0207 RMOV ─  Converting a 32-bit value into a 16-bit value
0208 GRY DGRY  Converting a binary number into a Gray code
3-17

API Symbol Function
0209 GBIN DGBIN  Converting a Gray code into a binary number
0210 NEG DNEG  Two’s complement of a number
_3 0211 ─ FNEG 
Reversing the sign of a 32-bit floating-point
number
Converting a binary floating-point number

0212 ─ FBCD 
into a decimal floating-point number
Converting a decimal floating-point number

0213 ─ FBIN 
into a binary floating-point number
Converting a binary numbers in blocks into a

0214 BKBCD ─ 
binary-coded decimal numbers in blocks
Converting a binary numbers in blocks into a

0215 BKBIN ─ 
0216 SCAL DSCAL  Finding a scaled value (point-slope)
0217 SCLP DSCLP  Finding a scaled value (two points)
0222 SCLM DSCLM  Multi-point area ratio operation
3-18
 Data transfer instructions

API Symbol Function
Transferring data
0300 MOV DMOV  S: Data source
D: Data destination
0302 $MOV ─  Transferring a string
0303 CML DCML  Inverting data

3_
0304 BMOV DBMOV  Transferring all data
0305 NMOV DNMOV  Transferring data to several devices
0306 XCH DXCH  Exchanging the data
0307 BXCH ─  Exchanging all data
0308 SWAP DSWAP  Exchanging the high byte with the low byte
0309 SMOV ─  Transferring the digits
0310 MOVB ─  Transferring several bits
3-19
 Jump instructions

API Symbol Function
0400 CJ ─  Conditional jump
0401 JMP ─ ─ Unconditional jump
0402 GOEND ─ ─ Jump to END
_3  Program execution instructions

API Symbol Function
0500 DI ─ ─ Disabling an interrupt
0501 EI ─ ─ Enabling an interrupt
0503 EIX ─ ─ Disabling a specific interrupt
0504 DIX ─ ─ Enabling a specific interrupt
 I/O refreshing instructions

API Symbol Function
0600 REF ─  Refreshing the I/O
Refreshing the values of high-speed

0601 ─ DHSRF 
comparison
0602 REFF ─  Refreshing the I/O filtering time
 Miscellaneous instructions

API Symbol Function
0700 ALT ─  Alternating between ON and OFF
0701 TTMR ─ ─ Teach mode timer
0702 STMR ─ ─ Special timer
3-20

API Symbol Function
0703 RAMP DRAMP ─ Cyclic ramp signal
0704 MTR ─ ─ Matrix input
0705 ABSD DABSD ─ Absolute drum sequencer

3_
0706 INCD ─ ─ Incremental drum sequencer
0708 ─ DPIDE ─ PID algorithm
Setting up to compare the inputs of

0709 XCMP ─ ─
multiple work stations
Comparing the outputs of multiple work

0710 YOUT ─ ─
stations
0711 ─ DSUNRS  Setting up the sunrise and sunset times
3-21
 Logic instructions

API Symbol Function
0800 WAND DAND  Logical AND operation
0801 MAND ─  Matrix AND operation

_3
0802 WOR DOR  Logical OR operation
0803 MOR ─  Matrix OR operation
0804 WXOR DXOR  Logical exclusive OR operation
0805 MXOR ─  Matrix exclusive OR operation
0808 WINV DINV  Logical reversed INV operation
0809 LD& DLD& ─ S1&S2
0810 LD| DLD| ─ S1|S2
0811 LD^ DLD^ ─ S1^S2
0812 AND& DAND& ─ S1&S2
0813 AND| DAND| ─ S1|S2
3-22

API Symbol Function
0814 AND^ DAND^ ─ S1^S2
0815 OR& DOR& ─ S1&S2
0816 OR| DOR| ─ S1|S2
3_
0817 OR^ DOR^ ─ S1^S2
 Rotation instructions

API Symbol Function
0900 ROR DROR  Rotating bits in a group to the right
Rotating bits in a group to the right with

0901 RCR DRCR 
the carry flag
0902 ROL DROL  Rotating bits in a group to the left
Rotating bits in a group to the left with

0903 RCL DRCL 
the carry flag
Rotating bits to the right or the left in a

0904 MBR ─ 
matrix
3-23
 Timer and counter instructions

API Symbol Function
Resetting the contact to OFF or clearing
1000 RST DRST ─
the value in the register
1001 TMR ─ ─ 16-bit timer (Unit: 100ms)
1002 TMRH ─ ─ 16-bit timer (Unit: 1ms)
_3
1003 CNT ─ ─ 16-bit counter
32-bit counter (Including the use of high-

1004 ─ DCNT ─
speed counters)
1005 ─ DHSCS ─ Setting high-speed comparison
1006 ─ DHSCR ─ Resetting high-speed comparison
1007 ─ DHSZ ─ High-speed input zone comparison
1008 ─ DSPD ─ Speed detection
1009 PWD ─ ─ Pulse width detection
Capturing the high-speed count value in

1010 ─ DCAP ─
the external input interrupt
1011 TMRM ─ ─ 16-bit timer (Unit: 10ms)
The start of the instruction execution time

1012 IETS ─ 
measurement
The end of the instruction execution time
1013 IETE ─ 
measurement
1014 ─ DHSCY ─ Cyclic counting, comparing and outputting
Detecting the time difference between two

1015 PPDT ─ ─
phases
3-24
 Shift instructions

API Symbol Function
Shifting the states of the devices to the

1100 SFTR ─ 
right
1101 SFTL ─  Shifting the states of the devices to the left
3_
Shifting the data in the word devices to the
1102 WSFR DWSFR 
right
Shifting the data in the word devices to the

1103 WSFL DWSFL 
left
Shifting the data and writing it to the word

1104 SFWR DSFWR 
device
Shifting the data and reading it from the

1105 SFRD DSFRD 
word device
1106 SFPO DSFPO  Reading the latest data from the data list
1107 SFDEL DSFDEL  Deleting the data from the data list
1108 SFINS DSFINS  Inserting the data into the data list
3-25

API Symbol Function
1109 MBS ─  Shifting the matrix bits
Shifting the values of the bits in the

1110 SFR DSFR 
registers by n bits to the right
_3 1111 SFL DSFL 

Shifting the values of the bits in the
registers by n bits to the left
Shifting the states of the n bit devices by

1112 BSFR ─ 
one bit to the right
Shifting the states of the n bit devices by

1113 BSFL ─ 
one bit to the left
1114 NSFR DNSFR  Shifting n registers to the right
1115 NSFL DNSFL  Shifting n registers to the left
 Data processing instructions

API Symbol Function
1200 SER DSER  Searching the data
1201 SUM DSUM  Number of bits whose states are ON
1202 DECO ─  Decoder
3-26

API Symbol Function
1203 ENCO ─  Encoder
1204 SEGD ─  Seven-segment decoding
1205 SORT DSORT  Sorting the data

3_
1206 ZRST ─  Resetting the zone
1207 BON DBON  Checking the state of the bit
1208 MEAN DMEAN  Mean
1209 CCD ─  Sum check
1210 ABS DABS  Absolute value
1211 MINV ─  Inverting the matrix bits
1212 MBRD ─  Reading the matrix bit
1213 MBWR ─  Writing the matrix bit
3-27

API Symbol Function
1214 MBC ─  Counting the bits with the value 0 or 1
1215 DIS ─  Disuniting 16-bit data
1216 UNI ─  Uniting 16-bit data
_3
1217 WSUM DWSUM  Getting the sum
1221 LIMIT DLIMIT  Confining a value within bounds
1222 BAND DBAND  Deadband control
1223 ZONE DZONE  Controlling the zone
1224 ─ FMEAN  Mean of the floating point numbers
1225 ─ FSUM  Sum of the floating point numbers
1226 ─ DTM  Transfer and move data
1227 ─ ZSET  Zone setup
3-28
 Structure creation instructions

API Symbol Function
1300 FOR ─ ─ Start of the nested loop
1301 NEXT ─ ─ End of the nested loop
1302 BREAK ─ ─ Terminating the FOR-NEXT loop
3_
 Module instructions

API Symbol Function
Reading the data from the control register

1400 FROM DFROM 
in the special module
Writing the data to the control register in

1401 TO DTO 
the special module
Setting output control parameters of PU

1402 ─ DPUCONF 
module
1403 PUSTAT ─ ─ Reading PU module output state
3-29

API Symbol Function
1404 ─ DPUPLS ─ PU module pulse output (no acceleration)
_3
Relative position output of PU module
1405 ─ DPUDRI ─ (with acceleration and deceleration)
Absolute addressing output of PU module

1406 ─ DPUDRA ─ (with acceleration and deceleration)
1407 ─ DPUZRN ─ PU module homing
1408 ─ DPUJOG ─ PU module jog output
1409 ─ DPUMPG ─ PU module MPG output
3-30

API Symbol Function
High-speed counter function of PU

1410 ─ DPUCNT ─ module
3_
1415 LCCAL ─ ─ LC module channel calibration
1416 ─ DLCWEI ─ Reading weight value via LC module
1417 ─ DMPID ─ PID algorithm for RTD/TC module
1418 ─ DHCCNT ─ HC module counter value counted
1419 ─ DHCCAP ─ HC module counter value captured
3-31

API Symbol Function
1420 HCDO ─ ─ HC module digital output point
_3
HC module counter value in comparison
1421 ─ DHCCMP ─
for output
HC module counter value in group

1422 ─ DHCCMPT ─
comparison for output
HC module measurements of frequency

1423 ─ DHCMEAS ─
and revolution
Read the parameter from the O-Link

1426 IOLINKR – –
device
3-32

API Symbol Function
Write the parameter into the IO-Link

1427 IOLINKW – –
device
3_
 Floating-point number instructions

API Symbol Function
1500 ─ FSIN  Sine of a floating-point number
1501 ─ FCOS  Cosine of a floating-point number
1502 ─ FTAN  Tangent of a floating-point number
1503 ─ FASIN  Arcsine of a floating-point number
1504 ─ FACOS  Arccosine of a floating-point number
1505 ─ FATAN  Arctangent of a floating-point number
1506 ─ FSINH  Hyperbolic sine of a floating-point number
Hyperbolic cosine of a floating-point

1507 ─ FCOSH 
number
Hyperbolic tangent of a floating-point

1508 ─ FTANH 
number
1509 ─ FRAD  Converting from degrees to radians
1510 ─ FDEG  Converting from radians to degrees
3-33

API Symbol Function
1511 SQR DSQR  Square root of a binary number
1512 ─ FSQR  Square root of a floating-point number
1513 ─ FEXP  Exponent of a floating-point number
_3
1514 ─ FLOG  Logarithm of a floating-point number
Natural logarithm of a binary floating-

1515 ─ FLN 
point number
Raising a floating-point number to a

1516 ─ FPOW 
power
1517 RAND ─  Random number
 Real-time clock instructions

API Symbol Function
1600 TRD ─  Reading the time
1601 TWR ─  Writing the time
1602 T+ ─  Adding the time
1603 T- ─  Subtracting the time
1604 HOUR ─ ─ Running-time meter
1605 TCMP ─  Comparing the time
3-34

API Symbol Function
1606 TZCP ─  Time zone comparison
1607 DST ─  Daylight saving time
1608 WWON ─ ─ Weekly working time setup 3_
 Peripheral instructions

API Symbol Function
1700 TKY DTKY ─ Ten-key keypad
1701 HKY DHKY ─ Sixteen-key keypad
1702 DSW ─ ─ DIP switch
1703 ARWS ─ ─ Arrow keys
1704 SEGL ─ ─ Seven-segment display with latches
 Communication instructions

API Symbol Function
1806 LRC ─ ─ Longitudinal parity check
1807 CRC ─ ─ Cyclic redundancy check
3-35

API Symbol Function
1808 MODRW ─ ─ Reading and Writing MODBUS data
Sending and receiving communication

1812 COMRS ─ ─
data
_3 Setting the communication format for a

1813 COMDF ─ 
serial communication port
Serial communication instruction,

1814 VFDRW ─ ─
exclusively for Delta AC motor drive
Serial communication instruction,

1815 ASDRW ─ ─
exclusively for Delta servo drive
Setting the parameters in the data

1816 CCONF ─ 
exchange table for a communication port
Reading and writing Modbus data without

1817 MODRWE ─ ─
using any flags
Reading and writing DeviceNet

1818 DNETRW ─ ─
communication data
User-defined CAN communication

1819 CANRS ─ ─
sending and receiving
Enabling Delta DMV detection and

1820 DMVSH ─ ─
communication
3-36

API Symbol Function
Execute the appointed communication

1821 DESO ─ ─
number of the data exchange table once
 Other instructions

API Symbol Function
1900 WDT ─  Watchdog timer
1901 DELAY ─  Delaying the execution of a program 3_
1902 GPWM ─ ─ General pulse width modulation
1904 EPUSH ─  Storing the contents of the index registers
1905 EPOP ─  Reading data into the index registers
1906 INFO ─  Reading the system data
 String processing instructions

API Symbol Function
Converting a signed decimal number

2100 BINDA DBINDA 
into ASCII code
Converting a binary hexadecimal

2101 BINHA DBINHA 
number into hexadecimal ASCII code
Converting a binary-coded decimal

2102 BCDDA DBCDDA 
number into ASCII code
Converting a signed decimal ASCII code

2103 DABIN DDABIN 
into a signed decimal binary number
Converting a hexadecimal ASCII code

2104 HABIN DHABIN 
into a hexadecimal binary number
3-37

API Symbol Function
Converting an ASCII code into a binary-

2105 DABCD DDABCD 
2106 $LEN ─  Calculating the length of a string
Converting a floating-point number into

2109 $FSTR ─ 
a string
Converting a string into a floating-point
2110 $FVAL ─ 
_3 number
Retrieving characters from a string

2111 $RIGHT ─ 
begins from the right.

2112 $LEFT ─ 
begins from the left.
2113 $MIDR ─  Retrieving a part of a string
2115 $SER ─  Searching a string
2116 $RPLC ─  Replacing the characters in a string
2117 $DEL ─  Deleting the characters in a string
2118 $CLR ─  Clearing a string
2119 $INS ─  Inserting a string
2122 SPLIT ─  Splitting a string
2123 MERGE ─  Merging a string
 Ethernet instructions

API instruction
Symbol Function
16-bit 32-bit
2200 SOPEN ─  Opening a socket
3-38

API instruction
Symbol Function
16-bit 32-bit
2201 SSEND ─  Sending data through the socket
2203 SCLOSE ─  Closing a socket
2204 MSEND ─  Sending an email
Converting an IP address of the integer

2206 INTOA ─ 
type into an IP address of the string type
Converting an IP address of the string
3_
2207 IATON ─  type into an IP address of the integer
type
2208 EIPRW ─ ─ Reading and writing EtherNet/IP data
2209 SCONF ─  Setting TCP/UDP socket parameters
2210 MCONF ─  Reading/Writing Modbus TCP data
2211 EMCONF1 ─  Setting email server parameter values
3-39

API instruction
Symbol Function
16-bit 32-bit
2212 EMCONF2 ─  Setting email address

_3
Memory card / File register instructions

API Symbol Function
Writing data from the PLC into a

2300 MWRIT ─ 
memory card
Reading data from the memory card

2301 MREAD ─ 
into the PLC
2302 MTWRIT ─  Writing a string into the memory card
2303 MEMW ─  Writing data into the file register
2304 MDEL ─  Deleting files on the memory card
 Task control instructions

API Symbol Function
2400 TKON ─  Enabling a cyclic task
2401 TKOFF ─  Disabling a cyclic task
 Sequential function charts (SFC) instructions

API Symbol Function
2500 SFCRUN – – Enabling SFC
3-40

API Symbol Function
2501 SFCPSE – – Pausing SFC
2502 SFCSTP – – Stopping SFC
 High-speed output instructions

API Symbol Function
High-speed pulse output (without ramp- 3_

2700 – DPLSY –
up/down process)
High-speed pulse output (with ramp-

2701 – DPLSR –
up/down process)
2702 PWM DPWM – Pulse width modulation
2703 JOG DJOG – JOG output
2704 – DZRN – Zero return
2705 – DPLSV – Adjustable pulse output
2706 – DDRVI – Relative position control
2707 – DDRVA – Absolute position control
2708 CSFO – – Catch speed and proportional output
2709 – DDRVM – Mark alignment positioning
2-Axis relative-coordinate point-to-point

2710 – DPPMR –
synchronized motion
2-Axis absolute-coordinate point-to-

2711 – DPPMA –
point synchronized motion
3-41

API Symbol Function
2-Axis relative-position clockwise arc

2712 – DCICR –
interpolation
2-Axis absolute-position clockwise arc

2713 – DCICA –
interpolation
_3 2714 – DCICCR –
2-Axis relative-position
counterclockwise arc interpolation
2-Axis absolute-position
2715 – DCICCA – counterclockwise arc
interpolation
2716 – DCCMR – Relative-position circle drawing
2717 – DCCMA – Absolute-position circle drawing
The position planning table controls the

2718 TPO – –
output
Setting single-axis output parameters in

2719 – DTPWS 
the position planning table
Setting linear interpolation parameters

2720 – DTPWL 
in the position planning table
Setting arc interpolation parameters in

2721 – DPTWC 
the position planning table
2723 – DPPGB – Point to point go back and forth
Zero return 2
2724 – DZRN2 –
(output direction can be set)
3-42
 Delta Special CANopen Communication Instructions

API Symbol Function
Initializing the servo for CANopen
2800 INITC – –
communication
2801 ASDON – – Servo-ON and Servo-OFF
Setting the acceleration time and

2802 CASD – –
deceleration time for a servo
2803 – DDRVIC – Servo relative position control

3_
2804 – DDRVAC – Servo absolute position control
2805 – DPLSVC – Servo speed control
2806 ZRNC DZRNC – Servo homing
Reading and writing CANopen

2807 COPRW – –
communication data
Writing multiple CANopen parameter

2808 COPWL DCOPWL –
values
2809 RSTD ─ ─ Sending Reset or NMT command
2810 ZRNM ─ ─ Setting the homing mode for Delta servo
2811 EMER ─ ─ Reading Emergency message
Controlling the tracking function of a

2812 – DCSFOC –
servo via communication
2813 ECAMD – – Downloading E-CAM chart to the Slave
3-43

API Symbol Function
2814 – DECAMS – E-CAM parameter setting and planning
Activating E-CAM control and displaying

2815 ECAMA – –
the status
_3
Modifying the starting address for E-
2816 ECAMC – – CAM chart and the E-CAM chart length
in the servo
2817 – DTQC – Torque control
2818 – DTQLC – Speed of torque control
3.4.2 Applied Instructions (Sorted Alphabetically)

Classification API Function
0114 $+ –  Linking two strings
2118 $CLR –  Clearing a string
2117 $DEL –  Deleting the characters in a string
2109 $FSTR –  Converting a floating-point number into a string
2110 $FVAL –  Converting a string into a floating-point number
2119 $INS –  Inserting a string
2112 $LEFT –  Retrieving characters in a string begins from the left.
2106 $LEN –  Calculating the length of a string

Symbol
2113 $MIDR –  Retrieving a part of a string
0302 $MOV –  Transferring a string

Retrieving characters in a string begins from the
2111 $RIGHT – 
right.
2116 $RPLC –  Replacing the characters in a string
2115 $SER –  Searching a string
0102 * D*  Multiplication of binary numbers
0103 / D/  Division of binary numbers
3-44

0100 + D+  Addition of binary numbers
1210 ABS DABS  Absolute value
0705 ABSD DABSD – Absolute drum sequencer
0700 ALT –  Alternating between ON and OFF
0043 AND$<> – – S1≠S2
0042 AND$= – – S1＝S2
0812 AND& DAND& – S1&S2
0814 AND^ DAND^ – S1^S2 3_

0813 AND| DAND| – S1|S2
0010 AND< DAND< – S1＜S2
0011 AND<= DAND<= – S1<=S2
0007 AND<> DAND<> – S1≠S2
0006 AND= DAND= – S1＝S2

A
0008 AND> DAND> – S1＞S2
0009 AND>= DAND>= – S1>=S2
0076 ANDZ< DANDZ< – |S1-S2|＜|S3|
0077 ANDZ<= DANDZ<= – |S1-S2|<=|S3|
0073 ANDZ<> DANDZ<> – |S1-S2|≠|S3|
0072 ANDZ= DANDZ= – |S1-S2|=|S3|
0074 ANDZ> DANDZ> – |S1-S2|＞|S3|
0075 ANDZ>= DANDZ>= – |S1-S2|>=|S3|
1703 ARWS – – Arrow key input
2801 ASDON – – Servo-ON and servo-OFF

Serial communication instruction exclusive for Delta
1815 ASDRW – –
servo drive
Converting a binary number into a binary-coded
0200 BCD DBCD 
decimal number
Converting a binary-coded decimal number into
ASCII code
Converting a binary-coded decimal number into a
0201 BIN DBIN 
binary number
B 2100 BINDA DBINDA  Converting a singed decimal number into ASCII code
Converting a binary hexadecimal number into the
hexadecimal ASCII code

Converting binary numbers in blocks into binary-
0214 BKBCD – 
coded decimal numbers in blocks
3-45

Converting binary numbers in blocks into binary-

0215 BKBIN – 
coded decimal numbers in blocks
0304 BMOV DBMOV  Transferring all data
1207 BON DBON  Checking the state of a bit
1302 BREAK – – Terminating the FOR-NEXT loop

Shifting the states of the n bit devices by one bit to
1113 BSFL – 
the left
Shifting the states of the n bit devices by one bit to
1112 BSFR – 
_3 the right
0307 BXCH –  Exchanging all data
User-defined CAN communication sending and
1819 CANRS – –
receiving
Setting the acceleration time and deceleration time
2802 CASD – –
for a servo
1209 CCD –  Checksum
Setting the parameters in the data exchange table of
1816 CCONF – 
a communication port
0065 CHKADR – – Checking the address of the pointer register
0400 CJ –  Conditional jump

Comparing tables
0063 CMPT< – 
ON: <
Comparing tables
0064 CMPT<= – 
ON: <=
C Comparing tables
0060 CMPT<> – 
ON: ≠
Comparing tables
0059 CMPT= – 
ON: =
Comparing tables
0061 CMPT> – 
ON: >
Comparing tables
0062 CMPT>= – 
ON: >=
1003 CNT – – 16-bit counter
Setting the communication format for a serial
1813 COMDF – 
communication port
1812 COMRS – – Sending and receiving communication data
2807 COPRW – – Reading and writing CANopen communication data
2808 COPWL DCOPWL – Writing multiple CANopen parameter values
1807 CRC – – Cyclic redundancy check
2708 CSFO – – Catch speed and proportional output
D 0101 – D-  Subtracting binary numbers
3-46

S1-S2=D
Capturing the high-speed count value in the external

1010 – DCAP –
input interrupt
2717 – DCCMA – Absolute-position circle drawing
2716 – DCCMR – Relative-position circle drawing
2713 – DCICA – 2-Axis absolute-position clockwise arc interpolation

2-Axis absolute-position counterclockwise arc
2715 – DCICCA –
interpolation
–
2-Axis relative-position counterclockwise arc 3_
2714 – DCICCR
interpolation
2712 – DCICR –
interpolation
1004 – DCNT – 32-bit counter
Controlling the tracking function of a servo via
2812 – DCSFOC –
communication
2707 – DDRVA – Absolute position control
2804 – DDRVAC – Servo absolute position control
2706 – DDRVI – Relative position control
2803 – DDRVIC – Servo relative position control
2709 – DDRVM – Mark alignment positioning
2814 – DECAMS – E-CAM parameter setting and planning

1419 – DHCCAP – HC module counter value captured
1421 – DHCCMP – HC module counter value in comparison for output
HC module counter value in group comparison for
1422 – DHCCMPT –
output
1418 – DHCCNT – HC module counter value counted
HC module measurements of frequency and
1423 – DHCMEAS –
revolution
1006 – DHSCR – Resetting high-speed comparison
1005 – DHSCS – Setting high-speed comparison

1014 – DHSCY – Cyclic counting, comparing and outputting
0601 – DHSRF  Refreshing the values of high-speed comparison
1007 – DHSZ – High-speed input zone comparison

1415 – DLCCAL – LC module channel calibration
1417 – DMPID – PID algorithm for RTD/TC module
0708 – DPIDE – PID algorithm

High-speed pulse output (with ramp-up/down
2701 – DPLSR –
process)
2705 – DPLSV – Adjustable pulse output
2805 – DPLSVC – Servo speed control
3-47

High-speed pulse output (without ramp-up/down

2700 – DPLSY –
process)
2723 – DPPGB – Point to point go back and forth
2-Axis absolute-coordinate point-to-point
2711 – DPPMA –
synchronized motion
2-Axis relative-coordinate point-to-point synchronized
2710 – DPPMR –
motion
Setting arc interpolation parameters in the position
2721 – DPTWC 
planning table
_3 1410 – DPUCNT – High-speed counter function of PU module
1402 – DPUCONF  Setting output control parameters of PU module
Absolute addressing output of PU module (with
1406 – DPUDRA –
acceleration and deceleration)
Relative position output of PU module (with
1405 – DPUDRI –
acceleration and deceleration)
1408 – DPUJOG – PU module jog output
1409 – DPUMPG – PU module MPG output
1404 – DPUPLS – PU module pulse output (no acceleration)
1407 – DPUZRN – PU module homing
1008 – DSPD – Detecting speed
0711 – DSUNRS – Setting up the sunrise and sunset times
1226 – DTM  Transfer and move data
Setting linear interpolation parameters in the position
2720 – DTPWL 
planning table
Setting single-axis output parameters in the position
2719 – DTPWS 
planning table
2817 – DTQC – Torque control
2818 – DTQLC – Speed of torque control
2704 – DZRN – Zero return
2724 – DZRN2 – Zero return 2 (output direction can be set)

Converting an ASCII code into a binary-coded
decimal number
Converting a signed decimal ASCII code into a
signed decimal binary number
1202 DECO –  Decoder
1901 DELAY –  Delaying the execution of a program

Execute the appointed communication number of the
1821 DESO – –
data exchange table once
0500 DI – – Disabling the interrupt
1215 DIS –  Disuniting the 16-bit data
3-48

Division of binary numbers for 16-bit

0118 DIV16 DIV32 
Division of binary numbers for 32-bit
0504 DIX – – Enabling a specific interrupt
1820 DMVSH – – Enabling Delta DMV detection and communication
1818 DNETRW – – Reading and writing DeviceNet communication data
1607 DST –  Daylight saving time
1702 DSW – – DIP switch

2815 ECAMA – – Activating E-CAM control and displaying the status
3_
Modifying the starting address for E-CAM chart and
2816 ECAMC – –
the E-CAM chart length in the servo
2813 ECAMD – – Downloading E-CAM chart to the Slave
0501 EI – – Enabling an interrupt

Reading and writing through an EtherNet/IP
2208 EIPRW – –
connection
E 0503 EIX – – Disabling a specific interrupt

2211 EMCONF1 –  Setting email server parameter values
2212 EMCONF2 –  Setting email address
2811 EMER – – Reading Emergency message
1203 ENCO –  Encoder
1905 EPOP –  Reading data into the index registers
1904 EPUSH –  Storing the contents of the index registers

Subtracting floating-point numbers
0105 – F- 
S1-S2=D
Multiplying floating-point numbers
0106 – F* 
S1*S2=D
Dividing floating-point numbers
0107 – F/ 
S1/S2=D
Adding floating-point numbers
0104 – F+ 
S1+S2=D
1504 – FACOS  Arccosine of the floating-point number
0028 – FAND< – S1＜S2

F
0029 – FAND<= – S1<=S2
0025 – FAND<> – S1≠S2
0024 – FAND= – S1＝S2
0026 – FAND> – S1＞S2
0027 – FAND>= – S1>=S2
1503 – FASIN  Arcsine of a floating-point number
1505 – FATAN  Arctangent of a floating-point number

Converting a binary floating-point number into a
0212 – FBCD 
decimal floating-point number
3-49

Converting a decimal floating-point number into a

0213 – FBIN 
binary floating-point number
0056 – FCMP  Comparing floating-point numbers
1501 – FCOS  Cosine of a floating-point number
1507 – FCOSH  Hyperbolic cosine of a floating-point number
1510 – FDEG  Converting radians to degrees
1513 – FEXP  The exponent of a floating-point number
_3 0022 – FLD< – S1＜S2
0023 – FLD<= – S1<=S2
0019 – FLD<> – S1≠S2
0018 – FLD= – S1＝S2
0020 – FLD> – S1＞S2
0021 – FLD>= – S1>=S2
1515 – FLN  Natural logarithm of a binary floating-point number
1514 – FLOG  Logarithm of a floating-point number
1224 – FMEAN  The mean of floating point numbers
0211 – FNEG  Reversing the sign of a floating-point number
0034 – FOR< – S1＜S2
0035 – FOR<= – S1<=S2
0031 – FOR<> – S1≠S2
0030 – FOR= – S1＝S2
0032 – FOR> – S1＞S2
0033 – FOR>= – S1>=S2
1516 – FPOW  Raising a floating-point number to a power
1509 – FRAD  Converting degrees to radians
1500 – FSIN  Sine of a floating-point number
1506 – FSINH  Hyperbolic sine of a floating-point number
1512 – FSQR  Square root of a floating-point number
1225 – FSUM  The sum of floating point numbers
1502 – FTAN  Tangent of a floating-point number
1508 – FTANH  Hyperbolic tangent of a floating-point number
0057 – FZCP  Floating-point zone comparison

Converting a binary integer into a binary floating-
0202 FLT DFLT 
point number
1300 FOR – – Start of a nested loop
Reading data from the control register in the
1400 FROM DFROM 
extension module
3-50

0402 GOEND – – Jumping to END

G
1902 GPWM – – General pulse width modulation

Converting a hexadecimal ASCII code into a
hexadecimal binary number
1420 HCDO – – HC module digital output point
H
1701 HKY DHKY – Hexadecimal key input
3_
1604 HOUR – – Running-time meter
Converting an IP address of the string type into an IP
2207 IATON – 
address of the integer type
1012 IETS – 
measurement
1013 IETE – 
measurement
0706 INCD – – Incremental drum sequencer

I 1906 INFO –  Reading the system data
2800 INITC – – Initializing the servo for CANopen communication

Converting a 32-bit floating-point number into a
0204 INT DINT 
binary integer
Converting an IP address of the integer type into an
2206 INTOA – 
IP address of the string type
1426 IOLINKR – – Read the parameter from the O-Link device
1427 IOLINKW – – Write the parameter into the IO-Link device
0401 JMP – – Unconditional jump

J
2703 JOG DJOG – JOG output
1416 LCWEI – – Reading weight value via LC module
0037 LD$<> – – S1≠S2
0036 LD$= – – S1＝S2
0809 LD& DLD& – S1&S2
0811 LD^ DLD^ – S1^S2
0810 LD| DLD| – S1|S2

L
0004 LD< DLD< – S1＜S2
0005 LD<= DLD<= – S1<=S2
0001 LD<> DLD<> – S1≠S2
0000 LD= DLD= – S1＝S2
0002 LD> DLD> – S1＞S2
0003 LD>= DLD>= – S1>=S2
3-51

0070 LDZ< DLDZ< – |S1-S2|＜|S3|
0071 LDZ<= DLDZ<= – |S1-S2|<=|S3|
0067 LDZ<> DLDZ<> – |S1-S2|≠|S3|
0066 LDZ= DLDZ= – |S1-S2|=|S3|
0068 LDZ> DLDZ> – |S1-S2|＞|S3|
0069 LDZ>= DLDZ>= – |S1-S2|>=|S3|

_3 1806 LRC – – Longitudinal parity check
0801 MAND –  Matrix AND operation
2304 MDEL –  Deleting files on the memory card
2123 MERGE –  Merging a string
1214 MBC –  Counting the bits with the value 0 or 1
0904 MBR –  Rotating the matrix bits
1212 MBRD –  Reading the matrix bit
1109 MBS –  Shifting the matrix bits
1213 MBWR –  Writing the matrix bit
0058 MCMP –  Matrix comparison
2210 MCONF –  Reading/Writing Modbus TCP data
1208 MEAN DMEAN  Mean
2303 MEMW –  Writing data into the file register
1211 MINV –  Inverting matrix bits

M  Converting a 16-bit value into a 32-bit value
0206 MMOV –
1808 MODRW – – Reading/Writing MODBUS data

Reading and writing Modbus data without using any
1817 MODRWE – –
flags
0803 MOR –  Matrix OR operation
0300 MOV DMOV  Transferring data
0310 MOVB –  Transferring several bits
2301 MREAD –  Reading data from the memory card into the PLC
2204 MSEND –  Sending an email
0704 MTR – – Matrix input
2302 MTWRIT –  Writing a string into the memory card
0117 MUL16 MUL32  Multiplying binary numbers for 16-bit/32-bit
2300 MWRIT –  Writing data from the PLC to the memory card
0805 MXOR –  Matrix exclusive OR operation
N 0210 NEG DNEG  Two’s complement
3-52

1301 NEXT – – End of the nested loop
0305 NMOV DNMOV  Transferring data to several devices
0049 OR$<> – – S1≠S2
0048 OR$= – – S1＝S2
0815 OR& DOR& – S1&S2
0817 OR^ DOR^ – S1^S2 3_

0816 OR| DOR| – S1|S2
0016 OR< DOR< – S1＜S2
0017 OR<= DOR<= – S1<=S2
0013 OR<> DOR<> – S1 ≠ S2
O 0012 OR= DOR= – S1＝S2
0014 OR> DOR> – S1＞S2
0015 OR>= DOR>= – S1>=S2
0082 ORZ< DORZ< – |S1-S2|＜|S3|
0083 ORZ<= DORZ<= – |S1-S2|<=|S3|
0079 ORZ<> DORZ<> – |S1-S2|≠|S3|
0078 ORZ= DORZ= – |S1-S2|=|S3|
0080 ORZ> DORZ> – |S1-S2|＞|S3|
0081 ORZ>= DORZ>= – |S1-S2|>=|S3|

1015 PPDT – – Detecting the time difference between two phases
1403 PUSTAT – – Reading PU module output state
P
1009 PWD – – Pulse width detection
2702 PWM DPWM – Pulse width modulation
0703 RAMP DRAMP – Ramp signal
1517 RAND –  Random number
0903 RCL DRCL  Rotating to the left with the carry flag
0901 RCR DRCR  Rotating to the right with the carry flag
0600 REF –  Refreshing the I/O
R 0602 REFF –  Refreshing the I/O filtering time
0207 RMOV –  Converting a 32-bit value into a 16-bit value
0902 ROL DROL  Rotating to the left
0900 ROR DROR  Rotating to the right
1000 RST DRST – Resetting the contact or clearing the register
2809 RSTD – – Sending Reset or NMT command
3-53

0216 SCAL DSCAL  Scale value operation
2203 SCLOSE –  Closing the socket
0217 SCLP DSCLP  Parameter type of scale value operation
2209 SCONF –  Setting TCP/UDP socket parameters
1204 SEGD –  Seven-segment decoding
1704 SEGL – – Seven-segment display with latches

_3 1200 SER DSER  Searching the data
2501 SFCPSE – – Causing SFC to pause
2500 SFCRUN – – Enabling SFC
2502 SFCSTP – – Stopping SFC
1107 SFDEL DSFDEL  Deleting the data from the data list
Shifting the values of the bits in the registers by n bits
1111 SFL DSFL 
to the left
S 1106 SFPO DSFPO  Reading the latest data from the data list
Shifting the values of the bits in the registers by n bits
1110 SFR DSFR 
to the right
1105 SFRD DSFRD  Shifting the data and reading it from the word device
1101 SFTL –  Shifting the states of the devices to the left
1100 SFTR –  Shifting the states of the devices to the right
1104 SFWR DSFWR  Shifting the data and writing it into the word device
0309 SMOV –  Transferring the digits
2122 SPLIT –  Splitting a string
2200 SOPEN –  Opening the socket
1205 SORT DSORT  Sorting the data
2201 SSEND –  Sending the data through the socket
0702 STMR – – Special timer
1201 SUM DSUM  Number of bits whose states are ON
0308 SWAP DSWAP  Exchange the high byte with the low byte
1603 T- –  Subtracting a time
1602 T+ –  Adding a time
1605 TCMP –  Comparing a time

T
2401 TKOFF –  Disabling a cyclic task
2400 TKON –  Enabling a cyclic task
1700 TKY DTKY – Ten key input
3-54

1001 TMR – – 16-bit timer (unit: 100 ms)
1002 TMRH – – 16-bit timer (unit: 1 ms)
1011 TMRM – – 16-bit timer (unit: 10 ms)

Writing the data to the control register in the special
1401 TO DTO 
module
2718 TPO – – The position planning table controls the output
1600 TRD –  Reading the time
0701 TTMR – – Teach mode timer

3_
1601 TWR –  Writing the time
1606 TZCP –  Time zone comparison
U 1216 UNI –  Uniting the 16-bit data

Serial communication instruction exclusively for Delta
V 1814 VFDRW – –
AC motor drive
1608 WWON – – Weekly working time setup
1900 WDT –  Watchdog timer
W 0802 WOR DOR  Logical OR operation
1103 WSFL DWSFL  Shifting data in the word devices to the left
1102 WSFR DWSFR  Shifting data in the word devices to the right
1217 WSUM DWSUM  Getting the sum
0306 XCH DXCH  Exchanging data

X Setup for comparing the inputs of multiple work
0709 XCMP – –
stations
Y 0710 YOUT – – Comparing the outputs of multiple work stations
Z 2806 ZRNC DZRNC – Servo homing
2810 ZRNM – – Setting the homing mode for Delta servo
1206 ZRST –  Resetting the zone
3-55
MEMO
_3
3-56
4
Chapter 4 Instruction Structure
Table of Contents
4.1 Applied Instructions - API Description .............................................. 4-2
4.2 Operand Usage Description ............................................................... 4-4
4.3 Restrictions on the Use of Instructions ............................................. 4-7
4.4 Index Registers ................................................................................. 4-9
4.5 Pointer Registers ............................................................................. 4-12
4.6 Pointer Registers of Timers ............................................................. 4-14
4.9 File Register .................................................................................... 4-20
4-1
4.1 Applied Instructions - API Description

This section describes the way this manual documents each API instruction. Every instruction has its own instruction
code and API number. The instructions are divided into sections based on the related functions of the instructions, so
that all the arithmetic instructions are in one section, and all the comparison instructions are in another section. The
following example uses the MOV instruction. The API number of the instruction in the table is 0300, the instruction code
is MOV, and the function is transferring data.
API Instruction code Operand Function
0300 D MOV P S，D Transferring the data
Device X Y M S T C HC D FR SM SR E K 16# “$” F

S            
D       
_4
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S       
D       
Pulse instruction 16-bit instruction 32-bit instruction

AS AS AS
Symbol:
S ： Data source
D ： Data destination
1. The devices used by the instruction are listed in the operand column. S, D, n, and m are used as the operands
according to their functions. When more than one operand is used, and these operands share the same function,
they are differentiated by subscripts; for example, S1, and S2.
2. If you can use a 16-bit instruction as a 32-bit instruction, the letter D prepended to the 16-bit instruction code to
form the 32-bit instruction form. If you can use the instruction as a pulse instruction, the letter P is appended to the
instruction code. For example, “D***P” in which “***” is the instruction code indicates a 32-bit pulse instruction.
3. F in the operand area indicates a single precision floating point number (32-bit).
4. The solid circle ● indicates that the device can be modified by an index register, and the hollow circle ○ indicates
that the device cannot be modified by an index register. For example, the data register designated by the operand
S can be modified by an index register.
5. The applicable model is indicated in the table. You can check whether you can use the instruction as a pulse
instruction, a 16-bit instruction, a 32-bit instruction, or a 64-bit instruction according to the information in the table.
6. If you want to use an instruction in a function block, and the output, input, and data devices are supported in the
operands, you have to use the pointer registers. AS indicates that to use a timer, a 16-bit counter, and a 32-bit
4-2
Ch a pt er 4 Ins tr uc t i on S tr uc t ur e
counter that are supported in the operands, you have to use the timer pointer register, the 16-bit counter pointer
register, and the 32-bit counter pointer register. Refer to Sections 4.4–4.7 for more information or Section 7.2.4 in
the ISPSoft manual.
7. The symbols representing the MOV instruction in ISPSoft are:
MOV, MOVP, DMOV, and DMOVP are the Instruction codes for this instruction
En: Enable
S: The data source (the applicable format of the operand is a word/double word.)
D: The data destination (the applicable format of the operand is a word/double word.)
Applied instructions composition
Some applied instructions are composed of instruction codes. For example, the EI, DI, and WDT instructions; however,
most applied instructions consist of instruction codes and several operands.
Every applied instruction has its own API number and instruction code. For example, the instruction code API 0300 is the
MOV (transfer data) instruction. You can enter an applied instruction in three ways.
Enter the instruction directly: you can enter the instruction in ISPSoft. For the MOV instruction, enter the instruction
4_
name and the operands to designate “MOV D0
Enter the instruction by dragging: you can drag the MOV instruction from APIs in ISPSoft to the ladder diagram editor.
Enter the instruction from the toolbar: you can click API/FB Selection on the toolbar in ISPSoft, and then click API.
Finally, click the MOV instruction in Data Transfer.
Source operand
S If there is more than one source operand, the source operands are represented by subscript (for
example S1, S2).
Destination operand
D If there is more than one destination operand, the destination operands are represented by
subscript (for example, D1, D2).
If the operand only can be a constant K/H or a register value, it is represented by m, m1, m2, n, n1, or n2.
The length of the operand (6-bit, 32-bit, or floating-point number instructions):
16-bit or 32-bit instructions
Operand values in instructions are divided into 16-bit values and the 32-bit values. In order to process data of difference
lengths, the instructions are divided into 16-bit and 32-bit instructions. To differentiate a 32-bit instruction from the 16-bit
form, a D is added in front of the 16-bit instruction code (16-bit MOV and 32-bit DMOV).
4-3
The floating-point number instruction
16-bit MOV instruction
When M1 is ON, the data in D0 is

transferred to D1.
32-bit DMOV instruction
When M1 is ON, the data in (D1,

D0) is transferred to (D3, D2).
Floating-point number instructions
Floating-point number instructions support 32-bit floating-point number instructions that correspond to the single-
_4 precision floating-point number instructions. Refer to Chapter 2 for more information about floating-point numbers.
32-bit single-precision floating-point number F+ instruction
When X0.0 is ON, the data in

(D11, D10) and (D21, D20) is
transferred to (D31, D30).
Continuous execution and pulse execution of instructions
1. Instruction execution can be divided into continuous and pulse execution. You can reduce the scan cycle with
pulse instructions because when the instruction is not executed, less time is needed to execute the program.
2. The pulse function allows the related instruction to enable the rising edge-triggered control input. The instruction is
ON for one scan cycle.
3. If the control input stays ON, and the related instruction is not executed, the control input must be switched from
OFF to ON again in order to execute the instruction.
4. The following shows the difference between pulse and continuous instruction:
Pulse execution When M1 switches from OFF to ON, the

MOVP instruction is executed once. The
instruction is not executed again in the scan
cycle. Therefore, it is called a pulse
instruction.
Continuous execution
Whenever M1 is ON during the scan cycle,
the MOV instruction is executed once.
Therefore, the instruction is called a
continuous instruction.
When the conditional contact M1 is OFF, neither instruction is executed, and the value in the destination operand D does
not change.
4-4
4.2 Operand Usage Description

There are 2 types of operands in the AS Series: user-defined and system-defined.
User-defined operands
• Input relays: X0.0–X63.15 or X0–X63
• Output relays: Y0.0–Y63.15 or Y0–Y63
• Internal relays: M0–M8191
• Stepping relays: S0–S2047
• Timers: T0–T511
• 16-bit counters: C0–C511
• 32-bit counters: HC0–HC255
• Data registers: D0–D29999 or D0.0–D29999.15
• File registers: FR0–FR65535

4_
• Special auxiliary flags: SM0–SM2047
• Special data registers: SR0–SR2047
• Index registers: E0–E9
• Constants: The decimal constants are indicated by K, and the hexadecimal constants are indicated by 16#.
• Strings: “$”
• Floating-point numbers: The single-precision floating-point numbers are indicated by F.
• The length of the data in one register is generally 16 bits. If you want to store 32-bit data in the register, designate
two consecutive registers for the data.
• If the operand in a 32-bit instruction uses D0, it occupies the 32-bit data register composed of (D1, D0). D1
represents the higher 16 bits, and D0 represents the lower 16 bits. The same rule applies to the timer and the 16-
bit counter.
• When you use the 32-bit counter HC as the data register, it can only be used by the operand in a 32-bit instruction.
• You can only use index registers in 16-bit instructions.
Refer to Chapter 2 Devices for more information.
4-5
System-defined operands
• The system assigns the variables to declare such as BOOL, WORD, INT and so on: U0–U16387 and W0–
W29999.
• To start or stop a task use the TK0–TK31 instructions.
The following table lists the pointer type variable symbols, the supporting devices and usage.
Pointer type Usage
Device range PR0–PR15，PR0.0–PR15.15
General pointer Maximum quantity Use up to 16 pointers in each function block

(Pointer) Variable symbols of WORD/DWORD/LWORD/INT/DINT/LINT
Can be assigned to types or data register, input relay or output relay devices
(e.g. X0, Y0, etc.)
Device range TR0–TR7
_4 Pointer for a timer

Maximum quantity Use up to 8 pointers in each function block
(T_POINTER)
Can be assigned to Variable symbols of timer type or timer type devices
Device range CR0–CR7

Pointer for a counter
Maximum quantity Use up to 8 pointers in each function block
(C_POINTER)
Can be assigned to Variable symbols of counter type or counter type devices
Device range HCR0–HCR7

Pointer for a high-
speed counter Maximum quantity Use up to 8 pointers in each function block
(HC_POINTER) Variable symbols of 32-bit counter type or 32-bit counter type
Can be assigned to
devices
4-6
4.3 Restrictions on the Use of Instructions

 You can use the following instructions only in function blocks: API0065 CHKADR, FB_NP, FB_PN, NED, ANED,
ONED, PED, APED, OPED
 You cannot use the following instruction in interrupt tasks: GOEND
 You cannot use the in function blocks: LDP, ANDP, ORP, LDF, ANDF, ORF, PLS, PLF, NP, PN, MC/MCR, GOEND
and all pulse instructions in applied instructions.
If you want to use some of the instructions mentioned above, you can use the substitute instructions in the
following table.
Instruction which cannot be used in the function block Substitute instruction in the function block
LDP/ANDP/ORP PED/APED/OPED
LDF/ANDF/ORF NED/ANED/ONED
PLS -
PLF - 4_
NP FB_NP
PN FB_PN
MC -
MCR -
All pulse instructions in applied commands *1
*1: Pulse instructions cannot be used in function blocks. If you want to get the function of the pulse instruction in a
function block, refer to the following example.
Example:
1. First, declare 10 bit variables tempBit[10] to be used in the system.
2. When StartBit1 switches from OFF to ON, method 1 (network 1) and method 2 (network 2) can only execute the
MOV instruction once; you can choose which one to use.
3. You cannot use the variable tempBit in the system more than once.
4-7
 Use the following instructions with the Ladder Programming Language

For the following instructions, you need to start the instruction execution while the PLC switch from STOP to RUN.
And when the following instructions stop executing, the PLC should stop programming too. It is suggested to use
the following instructions with the Ladder Programming Language. Do NOT use the programming language that
only does one time execution, for example, function blocks that only can be called once. Or do not use the
programming language that stops scanning once the executing the instruction stops, for example ST and SFC
programming languages. If the function block can be called several times by different programs, it is not suitable
for the following instructions either.
Type of Instruction Instructions

Timer and Counter
CNT, DCNT, DHSCS, DHSCR, DHSZ, DHSCY
Instructions
Peripheral
TKY, DTKY, HKY, DHKY, DSW, ARWS
Instructions
Miscellaneous
RAMP, DRAMP, MTR, INCD
Instruction
Module Instructions DPUCONF, PUSTAT
_4
CANopen
Communication COPRW, COPWL, DCOPWL, ZRNM, ECAMD, ECAMS, ECAMA, ECAMC
Instructions
Memory Card / File
MEMW
Register Instructions
Communication
DNETRW
Instructions
Other Instructions INFO
4-8
4.4 Index Registers

Index registers are 16-bit data registers. They are similar to the general register in that you can read data from them and
write data into them. However, they are mainly used as index registers. The range of index registers is E0–E9. It is not
recommended to use the index registers for global variables; they can only be used for partial variables and for
temporary.
Index registers are used as follows.
1. Using the register name to modify the device:
4_
When M0 is ON, E0=10, E1=17, D1@E0=D (1+10)=D11, D11 is ON.
NOTE 1: AS Series support using the register name to modify the device; for example, D0.1@E0 but does not
support 2-layered modification for example, [email protected]@E0.
NOTE 2: When E0=17, D0.1@E0=D0.(1+17)=D1.2, and D1.2 is ON. The bit part 1@E0=(1+17)=18. However, the
maximum bit number is 15. Since m=18/16=1 and the remainder is 2, the last modification result is D
(0+1).2=D1.2. D1.2 is ON.
When M0 is ON, E0=10, and M1@E0=M (1+10)=M11. M11 is ON.
4-9
2. Declaring the variables first, and then modifying the device:
 Declare the three variables StartBit, Var1, and Var2 in ISPSoft.
The type of StartBit is a Boolean array, and its size is 2 bits. The range is from StartBit[0] to StartBit[1].
The type of Var1 is a word array, and its size is 11 words. The range is from Var1[0] to Var1[10].
The type of Var2 is a word, and its size is one word.
 When StartBit[0] is ON, E0=10, E1=1, Var1[0]@E0=Var1[10], Var2=Var1[10], and

StarrtBit[0]@E1=StartBit[1]. StartBit[1] is ON.
_4
Additional remark: When you declare the variables in ISPSoft, and the variables are added to the contents of the
registers to form the addresses to the actual data, you must note the addresses to prevent the
program from being executed incorrectly.
3. Using index registers in an interrupt instruction:
 The index registers E0~E9 in the main program (e.g. POU, SFC, and FB) are different from the ones
(index registers E0~E9) in the interrupt program. They are independent groups of index registers and
they work separately.
 You can use ISPSoft to monitor the values of index registers in the main program.
 Application: If you use E0 in the main program and in the interrupt program. When an interrupt occurs,
before executing the interrupt program, the system stores the value of E0 in the main program. After
the interrupt program is executed, the value of E0 in the main program will be retained. So that the
interrupt program will not affect the value of E0 in the main program and the result of the main program
execution can stay unaffected.
 Refer to the following example, if you need to monitor the values of index registers E0-E9 in the
interrupt program, or if the main program is also using the values of index registers E0-E9 in the
interrupt program. (Note: It is NOT recommended to use index registers as global variables. If you
need to use it as a global variable, you need to declare or define other devices to use it as a global
variable.)
4-10
 Example: Declare D100 as the variable of the index register E0. And this example use MOVE
instruction to demonstrate. Whenever an external interrupt occurs at X0.0, the value in D200
accumulates the occurrences in the values in D1000 ~ D1199.
4_
4 - 11
4.5 Pointer Registers

 ISPSoft supports function blocks. When the variable declaration type is VAR_IN_OUT, and the data type is
POINTER, the variable is a pointer register. The value in the pointer register can refer directly to the value stored in
a device X, Y, or D; and the pointer register can point to the address associated with the variable set automatically
in ISPSoft.
 You can declare 16 pointer registers in every function block. The range is PR0–PR15, or PR0.0–PR15.15.
Example:
1. Create a program organization unit (POU) in ISPSoft.
2. Create a function block called FB0.
3. Create the program in the function block FB0.

_4
4. Declare the variable in the function block FB0.
Choose VAR_IN_OUT as the declaration type, Point1 as the identifier, POINTER as the data type. The variable is
the pointer register.
5. Declare the variable in the program organization unit (POU).
6. Call the function block FB0 in the program organization unit (POU).
7. The program in the program organization unit (POU) operates as shown below.
4-12
Network 1: When StartBit[0] is ON, the address of D0 is transmitted to Point 1 in FB0.
When VarBit1 in FB0 is ON, E0=1, Var1=D0, Point1@E0=D (0+1)=D1, and Var2=D1.
Network 2: When StartBit[1] is ON, the address of CVar1[0] is transmitted to Point1 in FB0.
4_
Var2=CVar1[1]。When VarBit1 in FB0 is ON, E0=1, Var1=CVar1[0], Point1@E0=CVar1
(0+1)=Cvar1[1], and Var2=CVar1[1].
4-13
4.6 Pointer Registers of Timers

 ISPSoft supports function blocks. If you want to use a timer in a function block, you must declare a timer pointer
register in the function block. The address of the timer is transmitted to the timer pointer register when the function
block is called.
 When the variable declaration type is VAR_IN_OUT, and the data type is T_POINTER, the variable is the timer
pointer register. The value in the timer pointer register can refer directly to the value stored in the device T, or in the
variable which is the timer in ISPSoft.
 You can declare up to 8 timer pointer registers in every function block. The range is TR0–TR7.
 If you want to use an instruction in the function block, and the timer is supported by the operands, you must use a
timer pointer register.
Example: using a timer in a function block.
2. Create a function block which is called FB0.

_4
Choose VAR_IN_OUT as the declaration type, TPoint1 as the identifier, and T_POINTER as the data type. The
variable is the timer pointer register.
4-14
4. The program in the function block FB0 appears as shown below.

4_
The data type of CVar1 should be TIMER.
Network 1: When StartBit[0] is ON, the address of T511 is transmitted to TPoint1 in FB0.
When VarBit1 in the FB0 is ON, the TMR instruction is executed, and TPoint1 (T511) starts counting.
When the value of TPoint1 matches the TPoint1 setting, VarOut is ON.
Network 2: When StartBit[1] is ON, the address of CVar1[0] is transmitted to TPoint1 in FB0.
When VarBit1 in FB0 is ON, the TMR instruction is executed, and TPoint (CVar1) starts counting.
When the value of TPoint1 matches the TPoint1 setting, VarOut is ON.
4-15
4.7 Pointer Registers for 16-bit Counters

 ISPSoft supports function blocks. If you want to use a 16-bit counter in a function block, you must declare a 16-bit
counter pointer register in the function block. The address of the 16-bit counter is transmitted to the 16-bit counter
pointer register when the function block is called.
 When the variable declaration type is VAR_IN_OUT, and the data type is C_POINTE, the variable is the 16-bit
counter pointer register. The value in the 16-bit counter pointer register can refer directly to the value stored in the
device T, or in the variable which is the counter in ISPSoft.
 You can declare up to eight 16-bit counter pointer registers in every function block. The range is CR0–CR7.
 If you want to use an instruction in the function block, and the counter is supported by the operands, you have to
use a 16-bit counter pointer register.
Example: using a 16-bit counter in a function block.

_4 2. Create a function block which is called FB0.
Choose VAR_IN_OUT as the declaration type, CPoint1 as the identifier, C_POINTER as the data type. The
variable is a 16-bit counter pointer register.
4. The program in the function block FB0 appears as shown below:
The data type of CVar1 should be COUNTER.
4-16
Network 1: When StartBit[0] is ON, the address of C0 is transmitted to CPoint1 in FB0.
When VarBit1 in FB0 is ON, CPoint1 (C0) is ON.
Network 2: When StartBit[1] is ON, the address of CVar1 is transmitted to CPoint1 in FB0.
4_
When VarBit1 in FB0 is ON, CPoint1 (CVar1) is ON.
4-17
4.8 Pointer Registers for 32-bit Counters

 ISPSoft supports function blocks. If you want to use a 32-bit counter in the function block, you must declare a 32-
bit counter pointer register in the function block. The address of the 32-bit counter is transmitted to the 32-bit
counter pointer register when the function block is called.
 When the variable declaration type is VAR_IN_OUT, and the data type is HC_POINTER, the variable is a 32-bit
counter pointer register. The value in a 32-bit counter pointer register can refer directly to the value stored in the
device HC or in the variable which is the counter in ISPSoft.
 You can declare up to eight 32-bit counter pointer registers in every function block. The range is HCR0–HCR7.
 If you want to use an instruction in the function block, and the 32-bit counter is supported by the operands, you
must use the 32-bit counter pointer register.
Example: using a 32-bit counter in a function block.
1. Create a function block called FB0.
_4
Choose VAR_IN_OUT as the declaration type, HCPoint1 as the identifier, HC_POINTER as the data type. The
variable is a 32-bit counter pointer register.
3. The program in the function block FB0 appears as follows:
The data type of CVar1 should be COUNTER, and you must fill in the address column with a valid address of the
32-bit counter.
6. The program in the program organization unit (POU) operates as follows:
Network 1: When StartBit[0] is ON, the address of HC0 is transmitted to HCPoint1 in FB0.
4-18
When VarBit1 in FB0 is ON, HCPoint1 (HC0) is ON.
Network: When StartBit[1] is ON, the address of CVar1 is transmitted to HCPoint1 in FB0.
When VarBit1 in FB0 is ON, HCPoint1 (CVar1) is ON.

4_
4-19
4.9 File Register

 AS Series PLC provides File registers (FR) for storing larger numbers of parameters.
 You can edit, upload, and download the parameters in the file registers with ISPSoft.
 The values in file registers can be read while the PLC is running. Refer to the MEMW instruction (API 2303) in the
AS300 Series Programming Manual for more information about how to read and write parameters to file registers.
_4
4-20
5
Chapter 5 Basic Instructions
Table of Contents
5.1 List of Basic Instructions ................................................................... 5-2
5.2 Basic Instructions.............................................................................. 5-3
5-1
A S S er i es Pr o gr am m ing Ma n ua l
5.1 List of Basic Instructions

The following table lists the Basic instructions covered in this chapter.
Operation
Instruction code Function Operand time
(µs)
Loading contact A/Connecting contact DX, X, Y, M, SM, S, T, C, HC, D
LD/AND/OR A in series/Connecting contact A in 0.025
parallel
Loading contact B/Connecting contact DX, X, Y, M, SM, S, T, C, HC, D
LDI/ANI/ORI B in series/Connecting contact B in 0.03
parallel
OUT Driving the coil DY, Y, M, SM, S, T, C, HC, D 0.04
SET Keeping the device on DY, Y, M, SM, S, T, C, HC, D 0.04
MC/MCR Setting/Resetting the master control N 0.24
Starting the rising-edge DX, X, Y, M, SM, S, T, C, HC, D
detection/Connecting the rising-edge
LDP/ANDP/ORP 0.22
detection in series/Connecting the
rising-edge detection in parallel
Starting the falling-edge DX, X, Y, M, SM, S, T, C, HC, D
detection/Connecting the falling-edge
LDF/ANDF/ORF 0.22
_5 falling-edge detection in parallel
Starting the rising-edge X, Y, M, SM, S, T, C, HC, D
detection/Connecting the rising
PED/APED/OPED 0.22
edge-detection in series/Connecting
the rising-edge detection in parallel
Starting the falling-edge X, Y, M, SM, S, T, C, HC, D
detection/Connecting the falling-edge
NED/ANED/ONED 0.22
falling-edge detection in parallel
PLS Rising-edge output Y, M, SM, S, D 0.22
PLF Falling-edge output Y, M, SM, S, D 0.22
INV Inverting the logical operation result – 0.22
NP The circuit is rising edge-triggered. – 0.24
PN The circuit is falling edge-triggered. – 0.24
FB_NP The circuit is rising edge-triggered. Y, M, S, D 0.24
FB_PN The circuit is falling edge-triggered. Y, M, S, D 0.24
5-2
C ha pt er 5 Bas ic I ns t r uc t i ons
5.2 Basic Instructions

Instruction code Operand Function
Loading contact A/Connecting contact A in
LD/AND/OR S
series/Connecting contact A in parallel
Device DX DY X Y M SM S T C HC D
S          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
LD S ： Specified device
AND
OR
5_
Explanation
1. LD applies to contact A that starts from the main line or contact A which is the start of a contact circuit. Use it to save
the current contents, and store the contact state in the accumulative register.
2. AND connects contact A in series. It reads the state of the contact that is specified as connected in series, and
performs the AND operation with the previous logical operation result. It stores the final result in the accumulative
register.
3. OR connects contact A in parallel. It reads the state of the contact that is specified as connected in parallel, and
performs the OR operation with the previous logical operation result. It stores the final result in the accumulative
register.
Example
1. Contact A of X0.0 is loaded, contact A of X0.1 is connected in series, contact A of X0.2 is connected in parallel, and
the coil Y0.0 is driven.
2. When both X0.0 and X0.1 are ON, or when X0.2 is ON, Y0.0 is ON.
5-3

Loading contact B/Connecting contact B in
LDI/ANI/ORI S
series/Connecting contact B in parallel
S          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
LDI S ： Specified device
ANI
ORI
Explanation
_5 1. LDI applies to contact B that starts from the main line or contact B that is the start of a contact circuit. Use it to save
the current contents, and store the contact state in the accumulative register.
2. ANI connects contact B in series. It reads the state of the contact that is specified as connected in series, and
performs the AND operation with the previous logical operation result. It stores the final result in the accumulative
register.
3. ORI connects contact B in parallel. It reads the state of the contact that is specified as connected in parallel, and
performs the OR operation with the previous logical operation result. It stores the final result in the accumulative
register.
Example
1. Contact B of X0.0 is loaded, contact B of X0.1 is connected in series, contact B of X0.2 is connected in parallel, and
the coil Y0.0 is driven.
2. When both X0.0 and X0.1 are ON, or when X0.2 is ON, Y0.0 is ON.
5-4
OUT D Driving the coil
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
D 
Symbol
D ： Specified device
Explanation
1. The logical operation result prior to the application of the OUT instruction is output to the specified device.
2. The following table describes the action of the coil contact.
OUT
Operation Contact
result Coil Contact A Contact B
5_
(normally open) (normally closed)
False OFF OFF ON
True ON ON OFF
Example
1. Contact B of X0.0 is loaded, contact A of X0.1 is connected in series, and the coil Y0.0 is driven.
2. When X0.0 is OFF, and X0.1 is ON, Y0.0 is ON.
5-5
SET D Keeping the device on
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
D 
Symbol
D ： Specified device
Explanation
When the instruction SET is driven, the specified device is set to ON. It does not matter if the SET instruction is still driven,
the specified device stays ON. You can set the specified device to OFF with the RST instruction.
Example
_5 1. Contact B of X0.0 is loaded, contact A of Y0.0 is connected in series, and Y0.1 stays ON.
2. When X0.0 is OFF, and Y0.0 is ON, Y0.1 is ON. Even if the operation result changes, Y0.1 still stays ON.
5-6
MC/MCR N Setting/Resetting the master control
Symbol
Level of the nested

MC N ： N0~N31
program structure
MCR
Explanation
1. MC sets the master control. When the MC instruction is executed, the instructions between MC and MCR are
executed as usual. When the MC instruction is OFF, the actions of the instructions between MC and MCR are as
described in the following table.
Instruction type Description
The timer value is reset to zero. The coil and the contact
General-purpose timer
are OFF.
The timer value is reset to zero. The coil and the contact
Timer in the function block
are OFF.
Accumulative timer
The coil is OFF. The timer value and the state of the 5_
contact remain the same.
The coil is OFF. The timer value and the state of the
Counter
contact remain the same.
Coils driven by OUT All coils are OFF.
Devices driven by SET and RST The states of the devices remain the same.
All applied instructions are not executed. The FOR/NEXT
loop is still repeated N times, but the actions of the
Applied instruction
instructions inside the FOR/NEXT loop follow those of the
instructions between MC and MR.
2. MCR resets the master control, and is placed at the end of the master control program. There should not be any
contact instruction before MCR.
3. MC/MCR supports the nested program structure. There are at most 32 levels of nested program structures
(N0–N31). Refer to the example below.
5-7
Example
_5
5-8

Starting the rising-edge detection/Connecting the
LDP/ANDP/ORP S rising-edge detection in series/Connecting the
rising-edge detection in parallel
S          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
LDP
ANDP S ： Specified device
ORP
Explanation
5_
1. LDP stores the current contents, and stores the rising-edge detection of the contact in the accumulative register.
2. ANDP connects the rising-edge detection of the contact in series.
3. ORP connects the rising-edge detection of the contact in parallel.
4. The system must scan LDP/ANDP/ORP to get the state of the device. Changes to the device state are not detected
until LDP/ANDP/ORP is scanned the next time.
5. Use the corresponding PED, APED, and OPED instructions in subroutines.
Example
1. The rising-edge detection of X0.0 starts, the rising-edge detection of X0.1 is connected in series, the rising-edge
detection of X0.2 is connected in parallel, and the coil Y0.0 is driven.
2. When both X0.0 and X0.1 are switched from OFF to ON, or when X0.2 is switched from OFF to ON, Y0.0 is ON for a
scan cycle.
5-9

Starting the falling-edge detection/Connecting the
LDF/ANDF/ORF S falling-edge detection in series/Connecting the
S          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
LDF
ANDF S ： Specified device
ORF
_5 Explanation
1. LDF saves the current contents, and stores the contact falling-edge detection in the accumulative register.
2. ANDF connects the falling-edge detection of the contact in series.
3. ORP connects the falling-edge detection of the contact in parallel.
4. The system must scan LDF/ANDF/ORF to get the state of the device. Changes to the device state are not detected
until LDF/ANDF/ORF is scanned the next time.
5. Use the corresponding NED, ANED, and ONED instructions in subroutines.
Example
1. The falling-edge detection of X0.0 starts, the falling-edge detection of X0.1 is connected in series, the falling-edge
2. When both X0.0 and X0.1 switches from OFF to ON, or when X0.2 switches from OFF to ON, Y0.0 is ON for a scan
cycle.
5-10

Starting the rising-edge detection/Connecting the rising
PED/APED/OPED S1，S2 edge-detection in series/Connecting the rising-edge
S1         
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S1 
S2 
Symbol
PED S1 ： Specified device
APED S2 ： For internal use

5_
Output the state of the

OPED Q ：
operation result
Explanation
1. PED/APED/OPED correspond to LDP/ANDP/ORP. The only difference between PED/APED/OPED and

LDP/ANDP/ORP is that you must specify the bit device S2 in which to store the previous state of the contact when
PED/APED/OPED is executed. Do not use the device S2 repeatedly in the program. Otherwise, the wrong execution
result appears.
2. APED connects the rising-edge detection of the contact in series.
3. OPED connects the rising-edge detection of the contact in parallel.
4. The system must scan PED/APED/OPED to get the state of the device. Changes to the device state are not
detected until PED/APED/OPED is scanned the next time
5. You can use PED/APED/OPED only in function blocks.
6. The state of the operation result is automatically output after the instruction is executed. You do not need to use an
input device for this.
5 - 11
Example
1. The rising-edge detection of X0.0 starts, the rising-edge detection of X0.1 is connected in series, the rising-edge
2. When both X0.0 and X0.1 switch from OFF to ON, or when X0.2 switches from OFF to ON, Y0.0 is ON for a scan
cycle.
_5
5-12

Starting the falling-edge detection/Connecting the
NED/ANED/ONED S1，S2 falling-edge detection in series/Connecting the
S1         
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S1 
S2 
Symbol
NED S1 ： Specified device
ANED S2 ： For internal use
5_
Output the state of

ONED Q ：
the operation result
Explanation
1. NED/ANED/ONED correspond to LDF/ANDF/ORF. The only difference between NED/ANED/ONED and

LDF/ANDF/ORF is that you must specify the bit device S2 in which to store the previous state of the contact when
NED/ANED/ONED is executed. Do not use the device S2 repeatedly in the program. Otherwise, the wrong
execution result appears.
2. ANED connects the falling-edge detection of the contact in series.
3. ONED connects the falling-edge detection of the contact in parallel.
4. The system must scan NED/ANED/ONED to get the state of the device. Changes to the device state are not
detected until NED/ANED/ONED is scanned the next time
5. You can use NED/ANED/ONED only in function blocks.
6. The state of the operation result is automatically output after the instruction is executed. You do not need to use
input device for this.
5-13
Example
1. The falling -edge detection of X0.0 starts, the falling -edge detection of X0.1 is connected in series, the falling -edge
2. When both X0.0 and X0.1 switch from OFF to ON, or when X0.2 switches from OFF to ON, Y0.0 is ON for a scan
cycle.
_5
5-14
PLS D Rising-edge output
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
D 
Symbol
PLS D ： Specified device
Explanation
1. When the conditional contact switches from OFF to ON, the PLS instruction is executed, and the device D sends out
a pulse for a scan cycle.
2. Do not use the PLS instruction in function blocks.
3. ISPSoft V3.06.01 supports data type D and the BOOL type variable for declaration. 5_
Example
When X0.0 is ON, M0 is ON for a pulse time. When M0 is ON, Y0.0 is set to ON.
Timing diagram
X0.0
On e sc an c y c le
M0.0
Y0.0
5-15
PLF D Falling-edge output
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
D 
Symbol
PLF D ：Specified device
Explanation
1. When the conditional contact switches from ON to OFF, the instruction PLF is executed, and the device D sends out
a pulse for a scan cycle.
2. Do not use the instruction PLS in function blocks.

_5
3. ISPSoft V3.06.01 supports data type D and the BOOL type variable for declaration.
Example
When X0.0 is ON, M0 is ON for a pulse time. When M0 is ON, Y0.0 is set to ON.
Timing chart
X0 .0
One scan c ycle
M0
Y0 .0
5-16
INV - Inverting the logical operation result
Symbol
Explanation
The logical operation result preceding the INV instruction is inverted, and the inversion result stored in the accumulative
register.
Example
When X0.0 is ON, Y0.0 is OFF. When X0.0 is OFF, Y0.0 is ON.
5_
5-17
NP - Triggering the circuit on the rising edge.
Symbol
Explanation
1. When the value in the accumulative register switches from 0 to 1, the NP instruction keeps the value 1 in the
accumulative register for a scan cycle. After the second scan cycle is finished, the value in the accumulative register
changes to 0.
2. Use the FB_NP instruction in function blocks.
Example
Instruction Operation
_5
LD M0 Contact A of M0 is loaded.
AND M1 Contact A of M1 is connected in series.
NP The circuit is rising edge-triggered.
OUT Y0.0 The coil Y0.0 is driven.
Timing diagram
M0
M1
One scan c ycle One scan c ycle
Y0 .0
5-18
PN - Triggering the circuit on the falling edge.
Symbol
Explanation
1. When the value in the accumulative register switches from 1 to 0, the PN instruction keeps the value 1 in the
changes to 0.
2. Use the FB_ PN instruction in function blocks.
Example
5_
PN The circuit is falling edge-triggered.
Timing diagram
M0
M1
One scan cycle One scan cycle
Y0 .0
5-19
FB_NP S Triggering the circuit on the rising edge.
S    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
S ： For internal use
Explanation
1. When the value in the accumulative register turns from 0 to 1, the FB_NP instruction keeps the value 1 in the
changes to 0.
_5 2. The previous state of the contact is stored in the bit device S. Do not use S repeatedly in the program. Otherwise,
the wrong execution result appears.
3. Use FB_NP only in function blocks.
Example
FB_NP D0.0 The circuit is rising edge-triggered.
Timing diagram
M0
M1
One scan cycl e One scan cycl e
Y0 .0
5-20
FB_PN S Triggering the circuit on the falling edge.
S    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
S 
Symbol
S ： For internal use
Explanation
1. When the value in the accumulative register switches from 1 to 0, the FB_PN instruction keeps the value 1 in the
changes to 0.
2. The previous state of the contact is stored in the bit device S. Do not use S repeatedly in the program. Otherwise,
5_
the wrong execution result appears.
3. Use FB_PN only in function blocks.
Example
FB_PN D0.0 The circuit is falling edge-triggered.
Timing diagram
M0
M1
One scan cycle One scan cycle
Y0 .0
5-21
MEMO
_5
5-22
6
Table of Contents
6.1 Comparison Instructions ....................................................................... 6-4
6.1.1 List of Comparison Instructions ............................................................. 6-4
6.1.2 Explanation of Comparison Instructions ................................................. 6-7
6.2 Arithmetic Instructions ....................................................................... 6-46

6.2.1 List of Arithmetic Instructions ..............................................................6-46
6.2.2 Explanation of Arithmetic Instructions ..................................................6-47
6.3 Data Conversion Instructions .............................................................. 6-78

6.3.1 List of Data Conversion Instructions .....................................................6-78
6.3.2 Explanation of Data Conversion Instructions ..........................................6-79
6.4 Data Transfer Instructions ................................................................ 6-121

6.4.1 List of Data Transfer Instructions ....................................................... 6-121
6.4.2 Explanation of Data Transfer Instructions ............................................ 6-122
6.5 Jump Instructions ............................................................................. 6-149

6.5.1 List of Jump Instructions ................................................................... 6-149
6.5.2 Explanation of Jump Instructions ....................................................... 6-150
6.6 Program Execution Instructions ........................................................ 6-158

6.6.1 List of Program Execution Instructions ................................................ 6-158
6.6.2 Explanation of Program Execution Instructions .................................... 6-159
6.7 IO Refreshing Instructions ................................................................ 6-171

6.7.1 List of IO Refreshing Instructions ....................................................... 6-171
6.7.2 Explanation of IO Refreshing Instructions ............................................ 6-172
6.8 Miscellaneous Instructions ................................................................ 6-179

6.8.1 List of Convenience Instructions......................................................... 6-179
6.8.2 Explanation of Convenience Instructions ............................................. 6-180
6.9 Logic Instructions .............................................................................. 6-233

6.9.1 List of Logic Instructions ................................................................... 6-233
6.9.2 Explanation of Logic Instructions........................................................ 6-234
6.10 Rotation Instructions....................................................................... 6-255

6.10.1 List of Rotation Instructions ............................................................. 6-255
6.10.2 Explanation of Rotation Instructions ................................................. 6-256
6-1
6.11 Timer and Counter Instructions ....................................................... 6-267

6.11.1 List of Timer and Counter Instructions .............................................. 6-267
6.11.2 Explanation of Timer and Counter Instructions ................................... 6-268
6.12 Shift Instructions ............................................................................ 6-310

6.12.1 List of Shift Instructions .................................................................. 6-310
6.12.2 Explanation of Shift Instructions ...................................................... 6-311
6.13 Data Processing Instructions .......................................................... 6-352

6.13.1 List of Data Processing Instructions .................................................. 6-352
6.13.2 Explanation of Data Processing Instructions ...................................... 6-353
6.14 Structure Creation Instructions ....................................................... 6-414

6.14.1 List of Structure Creation Instructions .............................................. 6-414
6.14.2 Explanation of Structure Creation Instructions ................................... 6-415
6.15 Module Instructions ........................................................................ 6-423

6.15.1 List of Module Instructions .............................................................. 6-423
6.15.2 Explanation of Module Instructions ................................................... 6-424
6.16 Floating-point Number Instructions ................................................ 6-526

6.16.1 List of Floating-point Number Instructions ......................................... 6-526
6.16.2 Explanation of Floating-point Number Instructions ............................. 6-527
6.17 Real-time Clock Instructions ........................................................... 6-562

6.17.1 List of Real-time Clock Instructions .................................................. 6-562
6.17.2 Explanation of Real-time Clock Instructions ....................................... 6-563
_6
6.18 Peripheral Instructions.................................................................... 6-594
6.18.1 List of Peripheral Instructions .......................................................... 6-594
6.18.2 Explanation of Peripheral Instructions ............................................... 6-595
6.19 Communication Instructions ........................................................... 6-611

6.19.1 List of Communication Instructions................................................... 6-611
6.19.2 Explanation of Communication Instructions ....................................... 6-612
6.19.3 Descriptions on the Communication-related Flags and Registers .......... 6-699
6.20 Other Instructions ........................................................................... 6-703

6.20.1 List of Other Instructions ................................................................ 6-703
6.20.2 Explanation of Other Instructions ..................................................... 6-704
6.21 String Processing Instructions ........................................................ 6-716

6.21.1 List of String Processing Instructions ................................................ 6-716
6.21.2 Explanation of String Processing Instructions ..................................... 6-717
6.22 Ethernet Instructions ...................................................................... 6-780

6.22.1 List of Ethernet Instructions ............................................................ 6-780
6.22.2 Explanation of Ethernet Instructions ................................................. 6-781
6-2
6.23 Memory Card Instructions ............................................................... 6-822

6.23.1 List of Memory Card Instructions ...................................................... 6-822
6.23.2 Explanation of Memory Card Instructions .......................................... 6-823
6.24 Task Control Instructions ................................................................ 6-843

6.24.1 List of Task Control Instructions ....................................................... 6-843
6.24.2 Explanation of Task Control Instructions ............................................ 6-844
6.25 SFC Instructions .............................................................................. 6-848

6.25.1 List of SFC Instructions ................................................................... 6-848
6.25.2 Explanation of SFC Instructions........................................................ 6-849
6.26 High-speed Output Instructions ...................................................... 6-856

6.26.1 List of High-speed Output Instructions .............................................. 6-856
6.26.2 Explanation of High-speed Output Instructions................................... 6-857
6.27 Delta CANopen Communication Instructions ................................... 6-970

6.27.1 List of Delta CANopen Communication Instructions ............................. 6-970
6.27.2 Explanation of Delta CANopen Communication Instructions ................. 6-971
6.27.3 Frequently asked questions in Delta special CANopen communication and
Troubleshooting ........................................................................... 6-1040
6_
6-3
6.1 Comparison Instructions

6.1.1 List of Comparison Instructions
The following table lists the Comparison instructions covered in this section.

API Function
0000 LD= DLD= – S1＝S2
0001 LD<> DLD<> – S1≠S2

0002 LD> DLD> – S1＞S2
0003 LD>= DLD>= – S1≧S2
0004 LD< DLD< – S1＜S2
0005 LD<= DLD<= – S1≦S2
0006 AND= DAND= – S1＝S2
0007 AND<> DAND<> – S1≠S2

0008 AND> DAND> – S1＞S2
0009 AND>= DAND>= – S1≧S2
0010 AND< DAND< – S1＜S2
0011 AND<= DAND<= – S1≦S2
0012 OR= DOR= – S1＝S2
0013 OR<> DOR<> – S1 ≠ S2

0014 OR> DOR> – S1＞S2
_6 S1≧S2
0015 OR>= DOR>= –
0016 OR< DOR< – S1＜S2
0017 OR<= DOR<= – S1≦S2
0018 – FLD= – S1＝S2
0019 – FLD<> – S1≠S2

0020 – FLD> – S1＞S2
0021 – FLD>= – S1≧S2
0022 – FLD< – S1＜S2
0023 – FLD<= – S1≦S2
0024 – FAND= – S1＝S2
0025 – FAND<> – S1≠S2

0026 – FAND> – S1＞S2
0027 – FAND>= – S1≧S2
0028 – FAND< – S1＜S2
0029 – FAND<= – S1≦S2
0030 – FOR= – S1＝S2
0031 – FOR<> – S1≠S2
6-4

API Function
0032 – FOR> – S1＞S2
0033 – FOR>= – S1≧S2
0034 – FOR< – S1＜S2
0035 – FOR<= – S1≦S2
0036 LD$= – – S1＝S2
0037 LD$<> – – S1≠S2

0042 AND$= – – S1＝S2
0043 AND$<> – – S1≠S2

0048 OR$= – – S1＝S2
0049 OR$<> – – S1≠S2

0056 – FCMP  Comparing the floating-point numbers
0057 – FZCP  Floating-point zone comparison
0058 MCMP –  Matrix comparison
Comparing tables
0059 CMPT= – 
ON: =
Comparing tables
0060 CMPT<> – 
ON: <>
Comparing tables
0061 CMPT> – 
ON: > 6_
Comparing tables
0062 CMPT>= – 
ON: ≧
Comparing tables
0063 CMPT< – 
ON: <
Comparing tables
0064 CMPT<= – 
ON: ≦
0065 CHKADR – – Checking the address in a pointer register

0066 LDZ= DLDZ= – |S1-S2|=|S3|
0067 LDZ<> DLDZ<> – |S1-S2|≠|S3|
0068 LDZ> DLDZ> – |S1-S2|＞|S3|
0069 LDZ>= DLDZ>= – |S1-S2|≧|S3|
0070 LDZ< DLDZ< – |S1-S2|＜|S3|
0071 LDZ<= DLDZ<= – |S1-S2|≦|S3|
0072 ANDZ= DANDZ= – |S1-S2|=|S3|

0073 ANDZ<> DANDZ<> – |S1-S2|≠|S3|
0074 ANDZ> DANDZ> – |S1-S2|＞|S3|
0075 ANDZ>= DANDZ>= – |S1-S2|≧|S3|
6-5

API Function
0076 ANDZ< DANDZ< – |S1-S2|＜|S3|
0077 ANDZ<= DANDZ<= – |S1-S2|≦|S3|
0078 ORZ= DORZ= – |S1-S2|=|S3|

0079 ORZ<> DORZ<> – |S1-S2|≠|S3|
0080 ORZ> DORZ> – |S1-S2|＞|S3|
0081 ORZ>= DORZ>= – |S1-S2|≧|S3|
0082 ORZ< DORZ< – |S1-S2|＜|S3|
0083 ORZ<= DORZ<= – |S1-S2|≦|S3|
_6
6-6
6.1.2 Explanation of Comparison Instructions
0000-0005 D LD※ S1，S2 Comparing values LD※

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      

－ AS AS
Symbol
S1 ： Data source 1
Taking LD= and DLD= for example

Explanation
1. These instructions compare the values in S1 and S2. Take the LD= instruction for example. When the comparison 6_
result is that the value in S1 is equal to that in S2, the continuity condition of the instruction is met. When the
comparison result is that the value in S1 is not equal to that in S2, the discontinuity condition of the instruction is
met.
2. Only the 32-bit instruction can use the 32-bit counter, but not the device E.
16-bit 32-bit Continuity Discontinuity

API number
instruction instruction condition condition
0000 LD＝ DLD＝ S1＝S2 S1≠S2
0001 LD＜＞ DLD＜＞ S1≠S2 S1＝S2
0002 LD＞ DLD＞ S1＞S2 S1≦S2
0003 LD＞＝ DLD＞＝ S1≧S2 S1＜S2
0004 LD＜ DLD＜ S1＜S2 S1≧S2
0005 LD＜＝ DLD＜＝ S1≦S2 S1＞S2
Example
1. When the value in C10 is equal to 200, Y0.10 is ON.
2. When the value in D200 is greater than -30, Y0.11 stays ON.
3. When the value in (C201, C200) is less than 678,493, or when M3 is ON, M50 is ON.
6-7
_6
6-8
0006-0011 D AND※ S1，S2 Comparing values AND※

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      

－ AS AS
Symbol
Taking AND= and DAND=

for example
Explanation
1. These instructions compare the values in S1 and S2. Take the AND= instruction for example. When the comparison
6_
result is that the value in S1 is equal to that in S2, the continuity condition of the instruction is met. When the
met.
16-bit Continuity Discontinuity

API number 32-bit instruction
instruction condition condition
0006 AND＝ DAND＝ S1＝S2 S1≠S2
0007 AND＜＞ DAND＜＞ S1≠S2 S1＝S2
0008 AND＞ DAND＞ S1＞S2 S1≦S2
0009 AND＞＝ DAND＞＝ S1≧S2 S1＜S2

0010 AND＜ DAND＜ S1＜S2 S1≧S2
0011 AND＜＝ DAND＜＝ S1≦S2 S1＞S2
Example
1. When X0.0 is ON and the current value in C10 is equal to 100, Y0.10 is ON.
2. When X0.1 is OFF and the value in D0 is not equal to -10, Y0.11 stays ON.
3. When X0.2 is ON and the value in (D11, D10) is less than 678,493, or when M3 is ON, M50 is ON.
6-9
_6
6-10
0012-0017 D OR※ S1，S2 Comparing values OR※

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
Pulse Instruction 16-bit instruction 32-bit instruction

－ AS AS
Symbol
Taking OR= and DOR= for example
Explanation
1. These instructions compare the values in S1 and S2. Take the OR= instruction for example. When the comparison
result is that the value in S1 is equal to that in S2, the continuity condition of the instruction is met. When the 6_
met.

API number
0012 OR＝ DOR＝ S1＝S2 S1≠S2
0013 OR＜＞ DOR＜＞ S1≠S2 S1＝S2
0014 OR＞ DOR＞ S1＞S2 S1≦S2
0015 OR＞＝ DOR＞＝ S1≧S2 S1＜S2
0016 OR＜ DOR＜ S1＜S2 S1≧S2
0017 OR＜＝ DOR＜＝ S1≦S2 S1＞S2
Example
1. When X0.1 is ON, or when the current value in C10 is equal to 100, Y0.10 is ON.
2. When both X0.2 and M30 are ON, or when the value in (D101, D100) is greater than or equal to 1000,000, M60 is
ON.
6 - 11
_6
6-12

Comparing floating-point numbers LD
0018-0023 FLD※ S1，S2
※

S1         
S2         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

－－ AS
Symbol
Taking FLD= for example
Explanation
1. These instructions compare the 32-bit single precision floating point number
6_
2. Compare values in S1 and S2. Take the FLD= instruction for example. When the comparison result is that the value
in S1 is equal to that in S2, the continuity condition of the instruction is met. When the comparison result is that the
value in S1 is not equal to that in S2, the discontinuity condition of the instruction is met. Refer to Additional
Remarks point 2 below for more information on the instruction of FLD=.

API number
0018 FLD＝ S1＝S2 S1≠S2
0019 FLD＜＞ S1≠S2 S1＝S2
0020 FLD＞ S1＞S2 S1≦S2
0021 FLD＞＝ S1≧S2 S1＜S2
0022 FLD＜ S1＜S2 S1≧S2
0023 FLD＜＝ S1≦S2 S1＞S2
6-13
Example
Take the FLD＝ instruction for example. When the value in D0 is equal to that in D2, Y0.0 is ON.
Additional remarks
1. If the value in S1 or S2 exceeds the range of values that can be represented by floating-point numbers, the contact
is OFF, SM is ON, and the error code in SR0 is 16#2013.
2. If the floating-point value in S1 or S2 is from external input, or from ISPSoft, chances are a minor value difference
may occur and the result of the “FLD=“ instruciton may not be dependable. Use instructions “FLD<” and” FAND>”
or “FLD>” and “FAND<” instead when the floating-point value in S1 or S2 is from external input, or from ISPSoft.
_6
6-14

0024-0029 FAND※ S1，S2
AND※

S1         
S2         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

－－ AS
Symbol
Taking FAND= and DFAND= for example
Explanation
1. These instructions compare the 32-bit single precision floating point numbers
6_
2. Compare values in S1 and S2. Take the FAND= instruction for example. When the comparison result is that the
value in S1 is equal to that in S2, the continuity condition of the instruction is met. When the comparison result is
that the value in S1 is not equal to that in S2, the discontinuity condition of the instruction is met.

API number
0024 FAND＝ S1＝S2 S1≠S2
0025 FAND＜＞ S1≠S2 S1＝S2
0026 FAND＞ S1＞S2 S1≦S2
0027 FAND＞＝ S1≧S2 S1＜S2

0028 FAND＜ S1＜S2 S1≧S2
0029 FAND＜＝ S1≦S2 S1＞S2
6-15
Example
Take the instruction FAND＝ for example. When X1.0 is ON and the value in D1 is equal to that in D2, Y1.0 is ON.
Additional remarks
_6
6-16

0030-0035 FOR※ S1，S2
OR※

S1         
S2         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

－－ AS
Symbol
S1 ： Data source1
S2 ： Data source2
Taking FOR= and DFOR= for

example
Explanation
1. These instructions compare the 32-bit single precision floating point numbers. 6_
2. Compare values in S1 and S2. Take the FOR= instruction for example. When the comparison result is that the value
in S1 is equal to that in S2, the continuity condition of the instruction is met. When the comparison result is that the
value in S1 is not equal to that in S2, the discontinuity condition of the instruction is met.

API number
0030 FOR＝ S1＝S2 S1≠S2
0031 FOR＜＞ S1≠S2 S1＝S2
0032 FOR＞ S1＞S2 S1≦S2
0033 FOR＞＝ S1≧S2 S1＜S2
0034 FOR＜ S1＜S2 S1≧S2
0035 FOR＜＝ S1≦S2 S1＞S2
6-17
Example
When X1.0 is ON, or when the value in D1 is equal to that in D2, Y1.0 is ON.
Additional remarks
_6
6-18

0036-
LD$※ S1，S2 Comparing strings LD$※
0037

S1       
S2       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

- AS -
Symbol
S1 ： Data source1
S2 ： Data source2
Taking LD$= for example
Explanation
1. These instructions compare the strings in S1 and S2.
2. S1 and S2 can contain strings up to 256 characters(16#00 the end symbol is included).
6_
3. Take the instruction LD$= for example. When the comparison result is that the value in S1 is equal to that in S2, the
continuity condition of the instruction is met. When the comparison result is that the value in S1 is not equal to that
in S2, the discontinuity condition of the instruction is met.

API number
0036 LD$＝ S1＝S2 S1≠S2
0037 LD$＜＞ S1≠S2 S1＝S2

4. Only when the data in S–S+n (n indicates the nth device, up to 256 characters in each string) includes 16#00 can
the data be compared complete strings. For example:
b 15 b8 b7 b0
S 16#32( 2) 16#31( 1)
S+1 16#34( 4) 16#33( 3)
S+2 16#00 16#35( 5)
" 12345 "
6-19
5. When the two strings are the same, the corresponding comparison results of the instructions are listed below. For
example:
b 15 b8 b7 b0 b 15 b8 b7 b0
S1 16#42(B) 16#41(A) Comparison sign S2 16#42(B) 16#41(A)

S 1 +1 16#44(D) 16#43(C) S 2 +1 16#44(D) 16#43(C)
S 1 +2 16#00 16#45(E) S 2 +2 16#00 16#45(E)
" ABCDE " " ABCDE "
Comparison symbol Comparison operation result

$＝ Continuity
$＜＞ Discontinuity
Example
When the string starting with the data in D0-16#00 is equal to the string staring with D2-16#00, Y0.0 is ON.
Additional remarks
_6 1. If the string contains more than 256 characters or the string does not end with 16#00, the instruction is not
executed, SM is ON, and the error code in SR0 is 16#200E.
2. During the string comparison, the string ends when the end symbol 16#00 is found. The symbol 16#00 determines
the length of the string.
6-20

0042-
AND$※ S1，S2 Comparing strings AND$※
0043

S1       
S2       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

- AS -
Symbol
S1 ： Data source1
S2 ： Data source2
Taking AND$= for example
Explanation
2. S1 and S2 can contain string up to 256 characters (16#00 the end symbol is included).
6_
3. Take the AND$= instruction for example. When the comparison result is that the value in S1 is equal to that in S2,
the continuity condition of the instruction is met. When the comparison result is that the value in S1 is not equal to
that in S2, the discontinuity condition of the instruction is met.
API number
0042 AND$＝ S1＝S2 S1≠S2
0043 AND$＜＞ S1≠S2 S1＝S2
Only when the data in S–S+n (n indicates the nth device, up to 256 characters in each string) includes 16#00 can
the instruction compare the data as complete strings. For example:
b 15 b8 b7 b0
S 16#32( 2) 16#31( 1)
S+1 16#34( 4) 16#33( 3)
S+2 16#00 16#35( 5)
" 12345 "
6-21
4. When two strings are the same, the corresponding comparison operation results of the instructions are listed
below. For example:
b 15 b8 b7 b0 b 15 b8 b7 b0
S1 16#42( B) 16#41( A) S2 16#42( B) 16#41( A)

Compar ison sign
S 1 +1 16#44( D) 16#43( C) S 2 +1 16#44( D) 16#43( C)
S 1 +2 16#00 16#45( E) S 2 +2 16#00 16#45( E)
" ABCDE " " ABCDE "

$＝ Continuity
Example
_6
Additional remarks
1. If the string contains more than 256 characters or the string does not end with 16#00, the instruction is not
6-22
0048-0049 OR$※ S1，S2 Comparing strings OR$※

S1       
S2       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 

- AS -
Symbol
S1 ： Data source1
S2 ： Data source2
Taking OR$= for example
Explanation
2. S1 and S2 can contain up to 256 characters (16#00 the end symbol is included). 6_
3. Take the instruction OR$= for example. When the comparison result is that the value in S1 is equal to that in S2, the
continuity condition of the instruction is met. When the comparison result is that the value in S1 is not equal to that
in S2, the discontinuity condition of the instruction is met.

API number
0048 OR$＝ S1＝S2 S1≠S2
0049 OR$＜＞ S1≠S2 S1＝S2
Only when the data in S–S+n (n indicates the nth device, up to 256 characters in each string) includes 16#00 can
the instruction compare the data as complete strings. For example:
b 15 b8 b7 b0
S 16#32( 2) 16#31( 1)
S+1 16#34( 4) 16#33( 3)
S+2 16#00 16#35( 5)
" 12345 "
6-23
4. When two strings are the same, the corresponding comparison operation results of the instructions are listed
below. For example:
b 15 b8 b7 b0 b 15 b8 b7 b0
S1 16#42( B) 16#41( A) S2 16#42( B) 16#41( A)

Compar ison sign
S 1 +1 16#44( D) 16#43( C) S 2 +1 16#44( D) 16#43( C)
S 1 +2 16#00 16#45( E) S 2 +2 16#00 16#45( E)
" ABCDE " " ABCDE "

$＝ Continuity
Example
_6
Additional remarks
1. If the string contains more than 256 characters or the string does not end with 16#00, the instruction is not
6-24
0054 D CMP P S1，S2，D Comparing values

S1           
S2           
D   DWORD  
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D 

AS AS AS
Symbol
S1 ： Comparison value1
S2 ： Comparison value2
D ： Comparison result
6_
Explanation
1. These instructions compare the single decimal numbers in S1 and S2 and store the comparison results in D.
2. The operand D occupies 3 consecutive devices. The comparison results are stored in D, D+1, and D+2. If the
value in S1 is greater than the value in S2, D is ON. If the value in S1 is equal to the value in S2, D+1 is ON. If the
value in S1 is less than the value in S2, D+2 is ON.
3. Only the DCMP and DCMPP instructions can use the 32-bit counter, but not the device E.
Example
1. If the operand D is M0, the comparison results are stored in M0, M1 and M2, as shown below.
2. When X0.0 is ON, the CMP instruction is executed. M0, M1, or M2 is ON. When X0.0 is OFF, the execution of the
CMP instruction stops and the state of M0, the state of M1, and the state of M2 remain unchanged.
6-25
3. If you need to clear the comparison result, use the RST or ZRST instruction.
Additional remarks
_6 1. If you declare the operand D in ISPSoft, the data type is ARRAY [3] of BOOL.
2. If D+2 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
6-26
0055 D ZCP P S1，S2，S，D Zone comparison

S1           
S2           
S           
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
S      
D 

AS AS AS
Symbol
Minimum value of the zone
S1 ：
comparison
Maximum value of the zone
S2 ：
comparison
S ： Comparison value
D ： Comparison result 6_
Explanation
1. These instructions compare signed decimal numbers in S and S1, and compare the signed decimal numbers in S
and S2, and stores the comparison results in D.
2. The value in S1 must be less than that in S2. If the value in S1 is larger than that in S2, S1 is the maximum/minimum
value during the execution of the ZCP instruction.
3. The operand D occupies three consecutive devices. The comparison results are stored in D, D+1, and D+2.
If the value in S1 is less than the value in S, D is ON.
If the value in S is between the values in S1 and S2, D+1 is ON.
If the value in S is greater than the value in S2, D+2 is ON.
4. Only the DZCP and DZCPP instructions can use the 32-bit counter, but not the device E.
6-27
Example
1. If the operand D is M0, the comparison results are stored in M0, M1 and M2, as shown below.
2. When X0.0 is ON, the ZCP instruction is executed. M0, M1, or M2 is ON. When X0.0 is OFF, the ZCP instruction is
not executed, and the state of M0, the state of M1, and the state of M2 remain unchanged.
3. If you need to clear the comparison result, use the RST or ZRST instruction.
_6
Additional remarks
1. If you declare the operand D in ISPSoft, the data type is ARRAY [3] of BOOL.
16#2003.
6-28
0056 FCMP P S1，S2，D Comparing floating-point numbers

S1         
S2         
D   DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS － AS
Symbol
S1 ： Floating-point comparison value1
S2 ： Floating-point comparison value2
Explanation 6_
1. This instruction compares the floating-point numbers in S1 and S2, and stores the comparison results (＞，＝，＜)
in D.
2. The operand D occupies three consecutive devices. The comparison results are stored in D, D+1, and D+2. If the
value in S1 is greater than the value in S1, D is ON. If the value in S1 is equal to the value in S2, D+1 is ON. If the
value in S1 is less than the value in S2, D+2 is ON.
Example
1. If the operand D is M10, the comparison results is stored in M10, M11 and M12, as shown below.
2. When X0.0 is ON, the FCMP instruction is executed. M10, M11, or M12 is ON. When X0.0 is OFF, the FCMP
instruction is not executed and the state of M10, the state of M11, and the state of M12 remain unchanged.
3. If you want to get the comparison result ≧, ≦, or ≠, connect M10–M12 is series or in parallel.
4. If you want to clear the comparison result, use the RST or ZRST instruction.
6-29
Additional remarks
1. If the value in S1 or S2 exceeds the range of values that can be represented by the floating-point numbers, the
contact is OFF, SM is ON, and the error code in SR0 is 16#2013.
16#2003.
_6
6-30
0057 FZCP P S1，S2，S，D Floating-point zone comparison

S1         
S2         
S         
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
S 
D 

AS － AS
Symbol
Minimum value of the zone
S1 ：
comparison
Maximum value of the zone
S2 ：
comparison
S ： Comparison value
Explanation
1. This instruction compares the floating-point numbers in S and S1, and compare the floating-point numbers in S with
that in S2, and then stores the results in D.
2. The value in S1 must be less than that in S2. If the value in S1 is larger than that in S2, S1 is the maximum/minimum
value during the execution of the FZCP instruction.
3. The operand D occupies three consecutive devices. The comparison results are stored in D, D+1, and D+2. If the
value in S1 is greater than the value in S, D is ON. If the value in S is between the value in S1 and the value in S2,
D+1 is ON. If the compared value in S2 is less than the value in S, D+2 is ON.
Example
1. If the operand D is M0, the comparison results are stored in M0, M1 and M2.
2. When X0.0 is ON, the FZCP instruction is executed. M0, M1, or M2 is ON. When X0.0 is OFF, the FZCP instruction
is not executed, and the state of M0, the state of M1, and the state of M2 remain unchanged.
3. If you want to clear the comparison result, use the RST or ZRST instruction.
6-31
Additional remarks
1. If the value in S1 or S2 or S exceeds the range of values that can be represented by the floating-point numbers, the
contact is OFF, SM is ON, and the error code in SR0 is 16#2013.
16#2003.
_6
6-32
0058 MCMP P S1，S2，n，D Matrix comparison

S1       
S2       
n         
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
n  
D  

AS AS －
Symbol
S1 ： Matrix source device 1
S2 ： Matrix source device 2
n ： Length of the array
： Pointer
D
6_
Explanation
1. This instruction searches for the bits with different states, starting from the bits specified by adding one to the
current value in D. After finding the bits with different states, the instruction stores the bit number in D, and the
comparison is finished.
2. The operand n must be between 1–256.
3. When SM607 is ON, the equivalent values are compared. When SM607 is OFF, the different values are compared.
When the matching bits are found, the comparison stops immediately, and SM610 is ON. When the last bits are
compared, SM608 is ON, and the bit number is stored in D. The comparison starts from the 0th bits in the next scan
cycle, and SM609 is ON. When the value in D exceeds the range, SM611 is ON.
4. When the MCMP instruction is executed, you need a 16-bit register to specify a certain bit among the 16n bits in
the matrix for the operation. The register is called the pointer, and is specified by you. The value in the register is
between 0–16n-1, and corresponds to the bit between b0 to b16n-1. During the operation, you are prevented from
altering the value of the pointer in case the search for the matching bits is affected. If the value of the pointer
exceeds the range, SM611 is ON, and the MCMP instruction is not executed.
5. If SM608 and SM610 occur simultaneously, they are ON simultaneously.
6-33
Example
1. When X0.0 is switched from OFF to ON, SM609 is OFF. The search for the bits with different states (SM607 is
OFF) starts from the bits specified by the adding one to the current value of the pointer.
2. Suppose the current value in D20 is 2. When X0.0 is switched from OFF to ON four times, you get the following
execution results.
 The value in D20 is 5, SM610 is ON, and SM608 is OFF.
 The value in D20 is 47, SM610 is OFF, and SM608 is ON.
2 Pointer
b0 D20
S1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
b47
MCMP
b0
_6
S2 0 1 0 1 0 1 0 1 0 1 1 1 0 1 0 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1
b47
Additional remarks
1. Operation error codes: If the devices S1+n-1 and S2+n-1 exceed the range, the MCMP instruction is not executed,
SM is ON, and the error code in SR0 is 16#2003. If the value in the operand n is not between 1 and 256, the
MCMP instruction is not executed, SM is ON, and the error code in SR0 is 16#200B.
2. Operation flags:
Matrix comparison flag.
SM607: ON: comparing equivalent values
OFF: comparing different values
SM608: The matrix comparison ends. When the last bits are compared, SM608 is ON.
SM609: ON: the comparison starts from bit 0.
Matrix bit search flag. When the matching bits are found, the comparison stops immediately, and
SM610:
SM610 is ON.
Matrix pointer error flag. When the value of the pointer exceeds the comparison range, SM611 is
SM611:
ON.
6-34
0059-0064 CMPT※ P S1，S2，n，D Comparing tables

S1         
S2       
n          
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
n  
D 

AS AS －
Symbol
S1 ： Source device 1
n ： Data length
Explanation
1. This instruction compares n signed decimal numbers in devices starting at S1 with those in devices starting at S2,
and then stores the comparison results in D.
3. The value that is written into the operand D is a one-bit value.
4. When the results of the comparison using the CMPT# instruction are that all devices are ON, SM620 is ON.
Otherwise, SM620 is OFF.
5. If the operand S1 is a device, the comparison is as shown below.

Compar ison result
S1 1234(BIN) S2 1111(B IN) D 1
S 1 +1 5678(BIN) S 2 +1 2222(BIN) D +1 1
S 1 +2 5000(BIN) Compar ison sign S 2 +2 3333(BIN) D +2 1
S 1 +3 1000(BIN) n > S 2 +3 4444(BIN) n D +3 0
~
S 1 +( N- 2) 10(BIN) S 2 +( N- 2) 8888(BIN) D +( N- 2) 0
S 1 +( N- 1) 90(BIN) S 2 +( N- 1) 9999(BIN) D +( N- 1) 0
6-35
6. If the operand S1 is a constant between -32768 to 32767, the comparison is as shown below.
Compar ison result
S2 1111(B IN) D 0
S 2 +1 2222(BIN) D +1 0
Compar iosn sign S 2 +2 3333(BIN) D +2 1
S1 3333(BIN) = S 2 +3 4444(BIN) n D +3 0
~
S 2 +( N- 2) 8888(BIN) D +( N- 2) 0
S 2 +( N- 1) 9999(BIN) D +( N- 1) 0
7. The corresponding comparison operation results of the instructions are listed in the following table.
Comparison operation result

API number 16-bit instruction
ON OFF
0059 CMPT＝ S1＝S2 S1≠S2
0060 CMPT＜＞ S1≠S2 S1＝S2
0061 CMPT＞ S1＞S2 S1≦S2
0062 CMPT＞＝ S1≧S2 S1＜S2
0063 CMPT＜ S1＜S2 S1≧S2
0064 CMPT＜＝ S1≦S2 S1＞S2
Example
The data in D0–D3 are compared with that in D10–D13. If the comparison result is that the data in D0–D3 are the same
as that in D10–D13, Y0.1–Y0.4 are ON.
_6
Comparison result
D0 1000 D10 1000 Y0.1 1

Comparison sign
D1 2000 = D11 1000 Y0.2 0
D2 3000 D12 1000 Y0.3 0

D3 4000 D13 1000 Y0.4 0
Additional remarks
1. If the value in the operand n is not between 1–256, the instruction is not executed, SM is ON, and the error code in
SR0 is 16#200B.
2. If the number of devices specified by S1–S1+n, S2–S2+n, or D is insufficient, the instruction is not executed, SM0 is
ON, and the error code in SR0 is 16#2003.
6-36

Checking the addresses in a pointer
0065 CHKADR S，n，D
register

S
n          
D   DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S
n  
D 

－ AS －
Symbol
S ： Pointer register
n ： Number of devices
D ： Check result
Explanation 6_
1. This instruction checks whether the value in S and (the value in S)+n-1 exceed the device range. If the result is
that the value in S and (the value in S)+n-1 do not exceed the device range, the device D is ON. Otherwise, it is
OFF.
2. S supports the pointer registers D, T, C, HC (POINTER/T_POINTER/C_POINTER/HC_POINTER).
4. You can use the CHKADR instruction only in a function block. Use CHKADR during the initial program
development phase or when you are not sure if the device range will be exceeded. After the program is written and
debugged, you can delete this instruction.
6-37
Example
1. Create a program (Prog0) and a function block (FB0) in ISPSoft.
Declare two variables in the program.
2. Declare VarPR1, VarTR1, VarCR1, and VarHCR1 in the function block, and assign the data types POINTER,
T_POINTER, C_POINTER, and HC_POINTER to them respectively.
_6
3. Call the function block FB0 in the program, and assign D29999, T0, C511, and HC50 to VarPR1, VarTR1, VarCR1,
and VarHCR1 in FB0 respectively.
4. Use the CHKADR instruction to check whether VarPR1, VarTR1, VarCR1, and VarHCR1 exceed the range.
5. When chkPR is ON, the actual device represented by VarPR1 is D29999. Since the legal range of devices is from
D0 to D29999, and D29999+10-1=D30008 which exceeds the range, PR_ChkBit is OFF.
6-38
6. When chkTR is ON, the actual device represented by VarTR1 is T0. Since the legal range of devices is from T0 to
T511, and T0+10-1=T9 which does not exceed the range, TR_ChkBit is ON.
7. When chkCR is ON, the actual device represented by C511. Since the legal range of devices is from C0 to C511,
and C511+10-1=C520 which exceeds the range, CR_ChkBit is OFF.
8. When chkHCR is ON, the actual device represented by HC50 is VarHCR1. Since the legal range of deices is from
HC0 to HC255, and HC50+10-1=HC59 which does not exceed the range, HCR_ChkBit is ON.
6_
Additional remarks
1. If the value (the actual device address) in S exceeds the device range, the CHKADR instruction is not executed,
SM is ON, and the error code in SR0 is 16#2003.
2. If the value in the operand n is not between 1–1024, the CHKADR instruction is not executed, SM is ON, and the
error code in SR0 is 16#200B.
6-39
0066- Comparing contact type

D LDZ※ S1，S2，S3
0071 absolute values LDZ※

S1           
S2           
S3           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
S3      

－ AS AS
Symbol
S1 ： Data source1
S2 ： Data source2
S3 ： Comparison result
_6
Taking LDZ= and DLDZ= for example
Explanation
1. These instructions compare the absolute value of the difference between S1 and S2 with the absolute value of S3.
Take the LDZ= instruction for example. If the comparison result is that the absolute value of the difference between
S1 and S2 is equal to the absolute value of S3, the continuity condition of the instruction is met. If the comparison
result is that the absolute value of the difference between S1 and S2 is not equal to the absolute value of S3, the
discontinuity condition of the instruction is met.
6-40
2. Only the 32-bit instruction can use the 32-bit HC device, but not the device E.

API number
0066 LDZ＝ DLDZ＝ | S1- S2|＝| S3| | S1- S2| ≠ | S3|
0067 LDZ＜＞ DLDZ＜＞ | S1- S2|≠| S3| | S1- S2|＝| S3|
0068 LDZ＞ DLDZ＞ | S1- S2|＞| S3| | S1- S2| ≦ | S3|
0069 LDZ＞＝ DLDZ＞＝ | S1- S2|≧| S3| | S1- S2|＜| S3|
0070 LDZ＜ DLDZ＜ | S1- S2|＜| S3| | S1- S2|≧ | S3|
0071 LDZ＜＝ DLDZ＜＝ | S1- S2|≦| S3| | S1- S2|＞| S3|
Example
1. When the absolute difference of D10 and D11 is greater than 200, Y0.0 is ON. While the absolute difference is less
than 200, Y0.0 is OFF.
6_
6-41

Comparing contact type
0072-0077 D ANDZ※ S1，S2，S3
absolute values ANDZ※

S1           
S2           
S3           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
S3      

－ AS AS
Symbol
S1 ： Data source1
S2 ： Data source2
_6
Taking ANDZ= and DANDZ= for

example
Explanation
Take the ANDZ= instruction for example. If the comparison result is that the absolute value of the difference
between S1 and S2 is equal to the absolute value of S3, the continuity condition of the instruction is met. If the
comparison result is that the absolute value of the difference between S1 and S2 is not equal to the absolute value
of S3, the discontinuity condition of the instruction is met.
6-42
Continuity Discontinuity
API number 16-bit instruction 32-bit instruction
condition condition
0072 ANDZ＝ DANDZ＝ | S1- S2|＝| S3| | S1- S2| ≠ | S3|
0073 ANDZ＜＞ DANDZ＜＞ | S1- S2|≠| S3| | S1- S2|＝| S3|
0074 ANDZ＞ DANDZ＞ | S1- S2|＞| S3| | S1- S2| ≦ | S3|
0075 ANDZ＞＝ DANDZ＞＝ | S1- S2|≧| S3| | S1- S2|＜| S3|

0076 ANDZ＜ DANDZ＜ | S1- S2|＜| S3| | S1- S2|≧ | S3|
0077 ANDZ＜＝ DANDZ＜＝ | S1- S2|≦| S3| | S1- S2|＞| S3|
Example
1. When M0 is ON and the absolute difference of D10 and D11 is greater than 200, Y0.0 is ON. While the absolute
difference is less than 200, Y0.0 is OFF.
6_
6-43

Comparing contact type
0078-0083 D ORZ※ S1，S2，S3
absolute values ORZ※

S1           
S2           
S3           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
S3      

－ AS AS
Symbol
S1 ： Data source1
S2 ： Data source2
_6
Taking ORZ= and DORZ= for example
Explanation
Take the ORZ= instruction for example. If the comparison result is that the absolute value of the difference between
S1 and S2 is equal to the absolute value of S3, the continuity condition of the instruction is met. If the comparison
result is that the absolute value of the difference between S1 and S2 is not equal to the absolute value of S3, the
discontinuity condition of the instruction is met.
6-44
Continuity Discontinuity
API number 16-bit instruction 32-bit instruction
condition condition
0078 ORZ＝ DORZ＝ | S1- S2|＝| S3| | S1- S2| ≠ | S3|
0079 ORZ＜＞ DORZ＜＞ | S1- S2|≠| S3| | S1- S2|＝| S3|
0080 ORZ＞ DORZ＞ | S1- S2|＞| S3| | S1- S2| ≦ | S3|
0081 ORZ＞＝ DORZ＞＝ | S1- S2|≧| S3| | S1- S2|＜| S3|

0082 ORZ＜ DORZ＜ | S1- S2|＜| S3| | S1- S2|≧ | S3|
0083 ORZ＜＝ DORZ＜＝ | S1- S2|≦| S3| | S1- S2|＞| S3|
Example
1. When M0 is ON and the absolute difference of D10 and D11 is greater than 200, Y0.0 is ON. While the absolute
difference is less than 200, Y0.0 is OFF.
6_
6-45
6.2 Arithmetic Instructions

6.2.1 List of Arithmetic Instructions
The following table lists the Arithmetic instructions covered in this section.

API Function
0100 + D+  Adding binary numbers
0101 - D-  Subtracting binary numbers
0102 * D*  Multiplying binary numbers
0103 / D/  Dividing binary numbers
0104 – F+  Adding floating-point numbers
0105 – F-  Subtracting floating-point numbers
0106 – F*  Multiplying floating-point numbers
0107 – F/  Dividing floating-point numbers
0114 $+ –  Linking strings

_6
MUL16: Multiplying binary numbers for 16-bit instructions

0117 MUL16 MUL32 
MUL32: Multiplying binary numbers for 32-bit instructions
DIV16: Dividing binary numbers for 16-bit instructions

0118 DIV16 DIV32 
DIV32: Dividing binary numbers for 32-bit instructions
6-46
Ch a pt er 6 A pp l i e d I n s tr uc t io ns
6.2.2 Explanation of Arithmetic Instructions
0100 D + P S1，S2，D Adding binary numbers

S1           
S2           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
Data
REAL
UINT
DINT
LINT
TMR
CNT
INT
type
S1      
S2      
D      

AS AS AS
Symbol
S1 ： Augend
S2 ： Addend
D ： Sum
6_
Explanation
1. This instruction adds the binary value in S2 to the binary value in S1, and stores the sum in D.
2. Only the 32-bit instructions can use the 32-bit counter, but not the device E.
3. Instruction flags: SM600 (zero flag), SM601 (borrow flag), and SM602 (carry flag)
4. When the operation result is zero, SM600 is ON. Otherwise, it is OFF.
5. For 16-bit binary values, when the operation result exceeds the range of 16-bit binary values, SM602 is ON.
Otherwise, it is OFF.
6. For 32-bit binary values, when the operation result exceeds the range of 32-bit binary values, SM602 is ON.
Otherwise, it is OFF.
6-47
Example 1
Adding 16-bit binary values: when X0.0 is ON, the instruction adds the addend in D10 to the augend in D0, and stores
the sum in D20.
 When the values in D0 and D10 are 100 and 10 respectively, D0 plus D10 equals 110, and 110 is stored in D20.
 When the values in D0 and D10 are 16#7FFF and 16#1 respectively, D0 plus D10 equals 16#8000, and 16#8000
is stored in D20.
 When the values in D0 and D10 are 16#FFFF and 16#1 respectively, D0 plus D10 equals 16#10000. Since the
operation result exceeds the range of 16-bit binary values, SM602 is ON, and the value stored in D20 is 16#0.
Since the operation result is 16#0, SM600 is ON.
Example 2
_6
Adding 32-bit binary values: when X0.0 is ON, the instruction adds the addend in (D41, D40) to the augend in (D31,
D30), and stores the sum in (D51, D50). The data in D30, D40, and D50 is the lower 16-bit data, whereas the data in
D31, D41, and D51 is the higher 16-bit data.
 When the values in (D31, D30) and (D41, D40) are 11111111 and 44444444 respectively, (D31, D30) plus (D41,
D40) equals 55555555, and 55555555 is stored in (D51, D50).
 When the values in (D31, D30) and (D41, D40) are 16#80000000 and 16#FFFFFFFF respectively, (D31, D30) plus
(D41, D40) equals 16#17FFFFFFF. Since the operation result exceeds the range of 32-bit binary values, SM602 is
ON, and the value stored in (D51, D50) is 16#7FFFFFFF.
6-48
Flags
For 16-bit binary values:
1. If the operation result is zero, SM600 is ON.
2. If the operation result exceeds 65,535, SM602 is ON.
For 32-bit values:
1. If the operation result is zero, SM600 is set to ON.
2. If the operation result exceeds 4,294,967,295, SM602 is set to ON.
The 16-bit instruction: Zero flag Zero flag Zero flag
65,535、0、1 65,535、0、1 65,535、0、1 、2
Borrow flag Carry flag
The 32-bit instruction: Zero flag Zero flag Zero flag
4,294,967,295 、0、1
6_
4,294,967,295 、0、1 4,294,967,295 、0、1、2
Borrow flag Carry flag
6-49
0101 D - P S1，S2，D Subtracting binary numbers

S1           
S2           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D      

AS AS AS
Symbol
S1 ： Minuend
S2 ： Subtrahend
D ： Difference
_6
Explanation
1. This instruction subtracts the binary value in S2 from the binary value in S1, and stores the difference in D.
4. When the operation result is zero, SM600 is ON. Otherwise, it is OFF.
5. When borrowing occurs during the arithmetic, SM601 is ON. Otherwise, it is OFF.
6-50
Example 1
Subtracting 16-bit binary values: when X0.0 is ON, the instruction subtracts the subtrahend in D10 from the minuend in
D0, and stores the difference in D20.
 When the values in D0 and D10 are 100 and 10 respectively, D0 minus D10 leaves 90, and 90 is stored in D20.
 When the values in D0 and D10 are 16#8000 and 16#1 respectively, D0 minus D10 leaves 16#7FFF, and
16#7FFF is stored in D20.
 When the values in D0 and D10 are 16#1 and 16#2 respectively, D0 minus D10 leaves 16#FFFF. Since borrowing
occurs during the operation, SM601 is ON, and the value stored in D20 is 16#FFFF.
 When the values in D0 and D10 are 16#0 and 16#FFFF respectively, D0 minus D10 leaves 16#F0001. Since
borrowing occurs during the operation, SM601 is ON, and the value stored in D20 is 16#1.
6_
Example 2
Adding 32-bit binary values: when X0.0 is ON, the instruction subtracts the subtrahend in (D41, D40) from the minuend in
(D31, D30), and stores the sum in (D51, D50). The data in D30, D40, and D50 is the lower 16-bit data, whereas the data
in D31, D41, and D51 is the higher 16-bit data.
 When the values in (D31, D30) and (D41, D40) are 55555555 and 11111111 respectively, (D31, D30) minus (D41,
D40) D10 leaves 44444444, and 44444444 is stored in (D51, D50).
 When the values in (D31, D30) and (D41, D40) are 16#80000000 and 16#FFFFFFFF respectively, (D31, D30)
minus (D41, D40) leaves 16#F80000001. Since borrowing occurs during the operation, SM601 is ON, and the
value stored in (D51, D50) is 16#80000001.
6-51
0102 D * P S1，S2，D Multiplying binary numbers

S1           
S2           
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D      

AS AS AS
Symbol:
S1 ： Multiplicand
S2 ： Multiplier
D ： Product
_6
Explanation
1. This instruction multiplies the signed binary value in S1 by the signed binary value in S2, and stores the product in
D.
2. Only the instruction D* can use the 32-bit counter.
3. Multiplying 16-bit binary values:
S1 S2 D +1 D
b15..............b0 b15..............b0 b31.........b16 b15...........b0
b15 is the si gn bit.

* b15 is the si gn bit.= b31, i.e. b15 in D+ 1, is the sign bit.
The product is a 32-bit value, and is stored in the register (D+1, D), which is composed of 32 bits. When the sign
bit b31 is 0, the product is a positive value. When the sign bit b31 is 1, the product is a negative value.
6-52
4. Multiplying 32-bit binary values:
S 1 +1 S1 S 2 +1 S2 D +3 D +2 D +1 D
b31...b16 b15...b0 b31...b16 b15...b0 b63...b48 b47...b32 b31...b16 b15...b0
* =
b31 is the si gn bit. b31 is the si gn bit. b63, i.e. b15 in D+3, is the sign bit.
The product is a 64-bit value, and is stored in the register (D+3, D+2, D+1, D0), which is composed of 64 bits.
When the sign bit b63 is 0, the product is a positive value. When the sign bit b63 is 1, the product is a negative
value.
Example
The instruction multiplies the 16-bit value in D0 by the 16-bit value in D10, and stores the 32-bit product in (D21, D20).
The data in D21 is the higher 16-bit data, whereas the data in D20 is the lower 16-bit data. Whether the result is a
positive value or a negative value depends on the state of the highest bit b31. When b31 is OFF, the result is a positive
value. When b31 is ON, the result is a negative value.
6_
D0×D10=(D21, D20)
16-bit value×16-bit value=32-bit value
6-53
0103 D / P S1，S2，D Dividing binary numbers

S1           
S2           
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D      

AS AS AS
Symbol
S1 ： Dividend
S2 ： Divisor
D ： Quotient; remainder
_6
Explanation
1. This instruction divides the signed binary value in S1 by the signed binary value in S2, and stores the quotient and
the remainder in D.
2. Only the 32-bit instructions can use the 32-bit counter.
3. When the sign bit is 0, the value is a positive one. When the sign bit is 1, the value is a negative one.
4. Dividing 16-bit values:
Quotient Remainder
S1 S2 D D+1
b15..............b0 b15..............b0 b15..............b0 b15..............b0

/ =
The operand D occupies two consecutive devices. The quotient is stored in D, and the remainder is stored in D+1.
6-54
5. Dividing 32-bit values:
Quotient Remainder
S 1 +1 S1 S 2 +1 S2 D+1 D D+3 D+2
b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0

/ =
The operand D occupies two devices. The quotient is stored in (D+1, D), and the remainder is stored in (D+3,
D+2).
Example
When X0.0 is ON, the instruction divides the dividend in D0 by the divisor in D10, and stores the quotient in D20, and
stores the remainder in D21. Whether the result is a positive value or a negative value depends on the state of the
highest bit.
6_
Additional remarks
1. If the device exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
2. If the divisor is 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2012.
3. If you declare the operand D used during the execution of the 16-bit instruction in ISPSoft, the data type is ARRAY
[2] of WORD/INT.
4. If you declare the operand D used during the execution of the 32-bit instruction in ISPSoft, the data type is ARRAY
[2] of DWORD/DINT.
6-55
0104 F+ P S1，S2，D Adding floating-point numbers

S1        
S2        
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS － AS
Symbol
S1 ： Augend
S2 ： Addend
D ： Sum
_6
Explanation
1. This instruction adds the 32-bit single-precision floating-point numbers in S2 and S1, and stores the sum in D.
 When the operation result is zero, SM600 is ON. Otherwise, it is OFF.
 When the absolute value of the operation result is less than the value that can be represented by the minimum
floating-point number, the value in D is 16#FF800000 and SM601 is ON.
 When the absolute value of the operation result is larger than the value that can be represented by the
maximum floating-point number, the value in D is 16#7F800000 and SM602 is ON.
Example
Adding single-precision floating-point numbers: when X0.0 is ON, the instruction adds the addend 16#4046B852 in (D21,
D20) to the augend 16#3FB9999A in (D11, D10), and stores the sum 16#4091C28F in (D31, D30). 16#4046B852,
16#3FB9999A, and 16#4091C28F represent the floating point numbers 3.105, 1.450, and 4.555 respectively.
6-56
Additional remark
If the value in S1 or the value in S2 exceeds the range of values that can be represented by the floating-point numbers,
the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2013.
6_
6-57
0105 F- P S1，S2，D Subtracting floating-point numbers

S1        
S2        
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS － AS
Symbol
S1 ： Minuend
S2 ： Subtrahend
D ： Difference
_6
Explanation
1. This instruction subtracts the 32-bit single-precision floating-point number in S2 from the 32-bit single-precision
floating-point numbers number in S1, and stores the difference in D.
 When the operation result is zero, SM600 is ON.
S 1 +1 S1 S 2 +1 S2 D+1 D
b31.........b16 b15...........b0 b31.........b16 b15...........b0 b31.........b16 b15...........b0

- =
6-58
Example
Subtracting 32-bit single-precision floating-point numbers: when X0.0 is ON, the instruction subtracts the subtrahend in
(D21, D20) from the minuend in (D21, D20), and stores the difference in (D31, D30).
Additional remarks
6_
6-59
0106 F* P S1，S2，D Multiplying floating-point numbers

S1        
S2        
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS － AS
Symbol
S1 ： Multiplicand
S2 ： Multiplier
D ： Product
_6
Explanation
1. This instruction multiplies the 32-bit single-precision floating-point number in S1 by the 32-bit single-precision floating-
point number in S2, and stores the product in D.
S 1 +1 S1 S 2 +1 S2 D+1 D
b31.........b16 b15...........b0 b31.........b16 b15...........b0 b31.........b16 b15...........b0

* =
6-60
Example
Multiplying 32-bit single-precision floating-point numbers: when X0.0 is ON, the instruction multiplies the multiplicand
32.5 by the multiplier in (D1, D0), and stores the product in (D11, D10).
Additional remarks
6_
6-61
0107 F/ P S1，S2，D Dividing floating-point numbers

S1        
S2        
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS - AS
Symbol
S1 ： Dividend
S2 ： Divisor
D ： Quotient
_6
Explanation
1. This instruction is divides the 32-bit single-precision floating-point number in S1 by the 32-bit single-precision
floating-point number in S2, and stores the quotient in D.
S 1 +1 S1 S 2 +1 S2 D +1 D
b31.........b16 b15...........b0 b31.........b16 b15...........b0 b31.........b16 b15...........b0

/ =
6-62
Example
Dividing 32-bit single-precision floating-point numbers: when X0.0 is ON, the instruction divides the dividend in (D1, D0)
by the divisor 100.7, and stores the quotient in (D11, D10).
Additional remarks
1. If the divisor is 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2012.
2. If the value in S1 or the value in S2 exceeds the range of values that can be represented by the floating-point
numbers, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2013.
6_
6-63
0112 D BK+ P S1，S2，n，D Adding binary values in blocks

S1       
S2         
n         
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
n    
D    

AS AS AS
Symbol
S1 ： Augend
S2 ： Addend
n ： Data length
_6 D ： Sum
Explanation
1. This instruction adds n pieces of data in devices starting from S2 to those in devices starting from S1. The augends
and the addends are binary values, and the instruction stores the sums in D.
4. When the operation result is zero, SM600 is ON.
5. For the 16-bit instructions, when the operation result is less than –32,768, SM601 is ON.
6. For the 16-bit instructions, when the operation result is larger than 32,767, SM602 is ON.
7. For the 32-bit instructions, when the operation result is less than–21,474,836,488, SM601 is ON.
8. For the 32-bit instructions, when the operation result is larger than 2,147,483,647, SM602 is ON.
6-64
9. 16-bit instruction example: when the operand S2 is a device (not a constant or a hexadecimal value)
} } }
S1 1 S2 1 D 1+1=2
S1 +1 2 + S2 +1 2 = D +1 2+2=4
.
.
.
.
n .
.
.
.
n .
.
.
. n
. . .
. . . . . .
. .
. .
. .
S1 +n-1 5 S2 +n-1 5 D +n-1 5+5=10
10. 16-bit instruction example: when the operand S2 is a constant or a hexadecimal value
} } }
S1 1 S2 10 D 1+10=11
S1 +1 2 + S2 10 = D +1 2+10=12
.
.
.
.
n .
.
.
.
n .
.
.
. n
. . .
. . . . . .
. .
. .
. .
S1 +n-1 5 S2 10 D +n-1 5+10=15
Example 1
When X0.0 is ON, the instruction adds the binary values in D10–D14 to the binary values in D0–D4, and stores the
sums.
6_
Ex ec ution res ult
D0 1 D10 10 D100 11
D1 2 D11 11 D101 13
D2 3 + D12 12 D102 15
D3 4 D13 13 D103 17
D4 5 D14 14 D104 19
6-65
Example 2
When X0.0 is ON, the instruction adds the addend 10 to the binary values in D0–D4, and stores the sums in D100–D104.
Ex ec ution res ult
D0 1 10 D100 11
D1 2 10 D101 12
D2 3 + 10 D102 13
D3 4 10 D103 14
D4 5 10 D104 15
Additional remarks
1. For 16-bit instructions, if the devices S1–S1+n-1, S2–S2+n-1, or D–D+n-1 exceed the device range, the instruction is
_6
not executed, SM is ON, and the error code in SR0 is 16#2003.
2. For 32-bit instructions, if the devices S1–S1+2*n-1, S2–S2+2*n-1, or D–D+2*n-1 exceed the device range, the
instruction is not executed, SM is ON, and the error code in SR0 is 16#2003.
3. If n is not between 1–256, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
4. For 16-bit instructions, if S1–S1+n-1 overlap D–D+n-1, the instruction is not executed, SM0 is ON, and the error code
in SR0 is 16#200C.
5. For 32-bit instructions, if S1–S1+2*n-1 overlap D–D+2*n-1, the instruction is not executed, SM0 is ON, and the error
code in SR0 is 16#200C.
in SR0 is 16#200C.
6-66
0113 D BK- P S1，S2，n，D Subtracting binary values in blocks

S1       
S2         
n         
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
n    
D    

AS AS AS
Symbol
S1 ： Minuend
S2 ： Subtrahend
n ： Data length
D ： Difference
6_
Explanation
1. This instruction subtracts n pieces of data in devices starting from S2 from those in devices starting from S1. The
minuends and the subtrahends are binary values, and the instruction stores the differences in D.
4. When the operation result is zero, SM600 is ON.
5. For 16-bit instructions, when the operation result is less than –32,768, SM601 is ON.
6. For 16-bit instructions, when the operation result is larger than 32,767, SM602 is ON.
7. For 32-bit instructions, when the operation result is less than –2,147,483,648, SM601 is ON.
6-67
8. For 32-bit instructions, when the operation result is larger than 2,147,483,647, SM602 is ON.
9. 16-bit instruction example: when the operand S2 is a device (not a constant or a hexadecimal value)
} } }
S1 5 S2 1 D 5-1=4
S1 +1 4 - S2 1 = D +1 4-1=3
.
.
.
.
n .
.
.
.
n .
.
.
. n
. . .
. . . . . .
. .
. .
. .
S1 +n-1 1 S2 1 D +n-1 1-1=0
10. 16-bit instruction example: when the operand S2 is a constant or a hexadecimal value
} } }
S1 5 S2 1 D 5-1=4
S1 +1 4 - S2 1 = D +1 4-1=3
.
.
.
.
n .
.
.
.
n .
.
.
. n
. . .
. . . . . .
. .
. .
. .
S1 +n-1 1 S2 1 D +n-1 1-1=0
Example 1
When X0.0 is ON, the instruction subtracts the binary values in D10–D14 from the binary values in D0–D4, and
stores the differences in D100–D104.

_6
Ex ec ution res ult
D0 5 D10 1 D100 4 1
D1 4 D11 2 D101 2 SM6 00
D2 3 - D12 3 D102 0
D3 2 D13 4 D103 -2
D4 1 D14 5 D104 -4
6-68
Example 2
When X0.0 is ON, the instruction subtracts the subtrahend 1 from the binary values in D0–D4, and stores the
differences in D100–D104.
Ex ec ution res ult
D0 10 1 D100 9
D1 9 1 D101 8
D2 8 - 1 D102 7
D3 7 1 D103 6
D4 6 1 D104 5
Additional remarks
1. For 16-bit instructions, if the devices S1–S1+n-1, S2–S2+n-1, or D–D+n-1 exceed the device range, the instruction is
not executed, SM is ON, and the error code in SR0 is 16#2003. 6_
2. For 32-bit instructions, if the devices S1–S1+2*n-1, S2–S2+2*n-1, or D–D+2*n-1 exceed the device range, the
instruction is not executed, SM is ON, and the error code in SR0 is 16#2003.
3. If n Is not between 1–256, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
in SR0 is 16#200C.
in SR0 is 16#200C.
6-69
0114 $+ P S1，S2，D Linking strings

S1       
S2       
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS AS －
Symbol
S1 ： String 1
S2 ： String 2
D ： Device in which the string is stored
Explanation
_6 1. This instruction links the string starting with the data in the device specified by S1 (exclusive of 16#00), and the string
starting with the data in the device specified by S2 (exclusive of 16#00) and stores the result in D. In addition, the
instruction adds the code 16#00 to the end of the linked string in D. When the instruction is not executed, the data
in D is unchanged.
2. When S1, S2 or D is not a string ($), the content of the data source can be up to 256 characters (including the ending
code 16#00).
3. If successful, the string in S1 and the string in S2 are linked and stored in D, as shown below.
S1 B (1 6# 62 ) A (1 6# 61 ) S2 B (1 6# 42 ) A (1 6# 41 ) D B (1 6# 62 ) A (1 6# 61 )
D( 16 #6 4) C( 16 #6 3) S2 +1 D( 16 #4 4) C( 16 #4 3) D( 16 #6 4) C( 16 #6 3)
S 1 +1 = D +1
S 1 +2 ( 16 #0 0) E (1 6# 65 ) 1 2 (1 6# 00 )
S2 + (1 6# 00 ) D +2 A (1 6# 41 ) E (1 6# 65 )
D +3 C( 16 #4 3) B (1 6# 42 )
D +
14 (1 6# 00 ) D( 16 #4 4)
T ur ning into 16#00 automati cally
6-70
S1 B (1 6# 62 ) A (1 6# 61 ) S2 B (1 6# 42 ) A (1 6# 41 ) D d (1 6# 62 ) a (1 6# 61 )
D( 16 #6 4) C( 16 #6 3) S2 +1 D( 16 #4 4) C( 16 #4 3) d (1 6# 64 ) c( 16 #6 3)
S 1 +1 = D +1
S 1 +2 E (1 6# 65 ) ( 16 #0 0) S2 +
12 (1 6# 00 ) (1 6# 00 ) D +2 B (1 6# 42 ) A (1 6# 41 )
D +3 D( 16 #4 4) C( 16 #4 3)
D +
14 (1 6# 00 ) ( 16 #0 0)
T ur ning into 16#00 automatic ally
4. When S1, S2 or D is not a string ($),the ending code 16#00 is added to the end of the data that is moved.
5. If S1 or S2 is not a string, then when the instruction is executed and the first character is the code 16#00, 16#00 is
still linked and moved.
6. The string “abcde” in S1 is shown as below.
S1 b(16#62) a(16#61)
S 1 +1 d(16#64) c(16#63)
S 1 +2 (16#00) e(16#65)
Example
Suppose S1 is the string “ab” and S2 is the string “c”. After the conditional contact M0 is enabled, the data in D65534 is
16#6261 and the data in D65535 is16#0063.
6_
Additional remarks
1. If S1 or S2 is a string, at most 31 characters can be moved.
2. If D is not sufficient to contain the string composed of the strings in S1 and S2, the instruction is not executed, SM0
is ON, and the error code in SR0 is 16#2003.
3. If the string of S1+S2 is more than 256 characters (the ending code 16#00 included), the instruction is not executed,
SM0 is ON, and the error code in SR0 is 16#2003.
4. If S1 or S2 overlaps D, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200C.
5. If the string in S1 or S2 does not end with 16#00, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200E.
6-71
0115 D INC P D Adding one to a binary number

D  DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D      

AS AS AS
Symbol
D ： Destination device
Explanation
_6 1. This instruction adds 1 to the value in D.
2. Only the DINC instruction can use the 32-bit counter.
3. For the 16-bit operation, 32,767 plus 1 equals -32,768. For the 32-bit operation, 2,147,483,647 plus 1 equals -
2,147,483,648.
Example
When X0.0 switches from OFF to ON, the value in D0 increases by one.
6-72
0116 D DEC P D Subtracting one from a binary number

D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D      

AS AS AS
Symbol
Explanation
1. This instruction subtracts 1 from the value in D.

6_
2. Only the DDEC instruction can use the 32-bit counter.
3. For the 16-bit operation, -32,768 minus 1 leaves 32,767. For the 32-bit operation, -2,147,483,648 minus 1 leaves
2,147,483,647.
Example
When X0.0 switches from OFF to ON, the value in D0 decreases by one.
6-73

MUL16 Multiplying 16-bit binary numbers
0117 P S1，S2，D
MUL32 Multiplying 32-bit binary numbers

S1           
S2           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D      

AS AS AS
Symbol
S1 ： Multiplicand
S2 ： Multiplier
D ： Product
_6
Explanation
1. This instruction multiplies the signed binary value in S1 by the signed binary value in S2, and stores the product in D.
2. Only the MUL32 instruction can use an HC device.
3. 16-bit binary multiplication:
S1 S2 D
b15..............b0 b15..............b0 b15..............b0
* =
Bit 15 is a sign bit. Bit 15 is a sign bit. Bit 15 is a sign bit.
The product is a 16-bit value stored in D which is a 16-bit register. If b15 in D is 0, the product stored in D is a positive
value. If b15 in D is 1, the product stored in D is a negative value.
6-74
4. 32-bit binary multiplication:
S 1 +1 S1 S 2 +1 S2 D +1 D
b31...b16 b15...b0 b31...b16 b15...b0 b31...b16 b15...b0
* Bit 31 is a si gn bit.= Bit 31 is a si gn bit.

Bit 31 is a si gn bit.
The product is a 32-bit value stored in (D, D+1) which is a 32-bit register. If b31 in D is 0, the product stored in (D, D+1) is
a positive value. If b31 in D is 1, the product stored in (D, D+1) is a negative value.
Example
The instruction multiplies the 16-bit value in D0 by the 16-bit value in D10, and stores the product in D20. The sign of the
product (positive or negative) depends on the leftmost bit (bit 15) in D20. If bit 15 in D20 is 0, the product stored in D20 is
a positive value. If bit 15 in D20 is 1, the product stored in D20 is a negative value.
6_
D0×D10=D20
16-bit value×16-bit value=16-bit value
Additional remarks
1. If the product of a 16-bit multiplication is not a 16-bit signed value available, and is greater than the maximum 16-bit
positive number K32767, or less than the minimum negative number K-32768, the carry flag SM602 is ON, and only
the low 16 bits are written.
2. If you need the complete result of a 16-bit multiplication (a 32-bit value), use the */*P instruction (API 0102). Refer to
the explanation for the * instruction (API 0102) for more information.
3. If the product of a 32-bit multiplication is not a 32-bit signed value available, and is greater than the maximum 32-bit
positive number K2147483647, or less than the minimum negative number K-2147483648, the carry flag SM602 is
ON, and only the low 32 bits are written.
4. If you need the complete result of a 32-bit multiplication (a 64-bit value), use API 0102 D*/D*P. Refer to the
explanation for the * instruction (API 0102) for more information.
6-75

DIV16 Dividing 16-bit binary numbers
0118 P S1，S2，D
DIV32 Dividing 32-bit binary numbers

S1           
S2           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      
D      

AS AS AS
Symbol
S1 ： Dividend
S2 ： Divisor
D ： Quotient; remainder
_6
Explanation
1. This instruction divides the signed binary value in S1 by the signed binary value in S2, and stores the quotient in D.
2. Only the 32-bit instruction can use an HC device.
3. Sign bit=0 (Positive number); sign bit =1 (Negative number)
4. 16-bit binary division:
Quotient
S1 S2 D
b15..............b0 b15..............b0 b15..............b0

/ =
The quotient is stored in D.
6-76
5. 32-bit binary division:
Quotient
S 1 +1 S1 S 2 +1 S2 D+1 D
b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0 b15.....b0

/ =
D occupies two consecutive devices. The quotient is stored in (D+1, D).
Example
When X0.0 is ON, the instruction divides the dividend in D0 by the divisor in D10, and stores the quotient D20.
Whether the quotient is a positive value or a negative value depends on the leftmost bit in D20.
Additional remarks
6_
1. If the device is not available, the instruction is not executed, SM0 will be ON, and the error code stored in SR0 is
16#2003.
2. If the divisor is 0, the instruction is not executed, SM0 will be ON, and the error code stored in SR0 is 16#2012.
3. If you want to store the remainder, use the “/” instruction (Dividing binary values). Refer to the explanation for the “/”
instruction (API 0103) for more information.
6-77
6.3 Data Conversion Instructions

6.3.1 List of Data Conversion Instructions
The following table lists the Data Conversion instructions covered in this section.

API Function
0200 BCD DBCD  Converting a binary number into a binary-coded decimal number
0201 BIN DBIN  Converting a binary-coded decimal number into a binary number
0202 FLT DFLT  Converting a binary integer into a binary floating-point number
0204 INT DINT  Converting a 32-bit floating-point number into a binary integer
0206 MMOV –  Converting a 16-bit value into a 32-bit value
0207 RMOV –  Converting a 32-bit value into a 16-bit value
0210 NEG DNEG  Two’s complement
0211 – FNEG  Reversing the sign of a 32-bit floating-point number
Converting a binary floating-point number into a decimal

0212 – FBCD 
_6 Converting a decimal floating-point number into a binary

0213 – FBIN 
– Converting a binary numbers in blocks into a binary-coded

0214 BKBCD 
decimal numbers in blocks
– Converting a binary numbers in blocks into a binary-coded

0215 BKBIN 
decimal numbers in blocks
0216 SCAL DSCAL  Finding a scaled value (point-slope)
0217 SCLP DSCLP  Finding a scaled value (two points)
6-78
6.3.2 Explanation of Data Conversion Instructions
Converting a binary number into a

0200 D BCD P S, D
binary-coded decimal number

S         
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
D      

AS AS AS
Symbol
S ： Source device
D ： Conversion result
6_
Explanation
1. This instruction converts a binary value in S into a binary-coded decimal value, and stores the conversion result in
D.
2. Only the DBCD instruction can use the 32-bit counter, but not the device E.
3. The four fundamental arithmetic operations in the PLC, the INC instruction, and the DEC instruction all operate on
binary numbers. To show the decimal value on the display, use the BCD instruction to convert a binary value into a
binary-coded decimal value
6-79
Example
1. When X0.0 is ON, the instruction converts a binary value in D10 into a binary-code decimal value, and stores the
conversion result in D100.
2. If D10=16#04D2=1234, the conversion result is D100=16#1234.
Additional remarks
1. If the conversion result exceeds the range 0–9,999, the instruction BCD is not executed, SM0 is ON, and the error
code in SR0 is 16#200D. The binary-coded decimal value is represented by the hexadecimal value, but one of
digits is not between 0–9.
2. If the conversion result exceeds the range 0–99,999,999, the instruction DBCD is not executed, SM0 is ON, and
the error code in SR0 is 16#200D. The binary-coded decimal value is represented by the hexadecimal value, but
one of digits is not between 0–9.
_6
6-80

0201 D BIN P S, D
number into a binary number

S         
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
D      

AS AS AS
Symbol
S ： Source device
Explanation
1. This instruction converts a binary-coded decimal value in S into a binary value, and stores the conversion result in 6_
D.
2. The 16-bit binary-coded decimal value in S must be between 0–9,999, and the 32-bit binary-coded decimal value
in S must be between 0–99,999,999.
4. The system converts constants and hexadecimal values into binary values automatically. Therefore, you do not
need to use the instruction for that conversion.
Example
When X0.0 is ON, the instruction converts the binary-coded decimal value in D0 into the binary value, and stores the
conversion result in D10.
6-81
Additional remarks
1. If the value in S is not the binary-coded decimal value, an operation error occurs, SM0 is ON, and the error code in
SR0 is 16#200D. The binary-coded decimal value is represented by the hexadecimal value, but one of digits is not
between 0–9.
2. Application of the BCD and BIN instructions:
 Before the value of the binary-coded decimal type of DIP switch is read into the PLC, use the BIN instruction
to convert the data into the binary value and store the conversion result in the PLC.
 If you want to display the data stored inside the PLC in a seven-segment display of the binary-coded decimal
type, use the BCD instruction to convert the data into the binary-coded decimal value before the data is sent
to the seven-segment display.
 When X1.0 is ON, the BIN instruction converts the binary-coded decimal value in X0.0–X0.15 into the binary
value, and stores the conversion result in D100. Subsequently, the BCD instruction converts the binary value
in D100 into the binary-coded decimal value, and stores the conversion result in Y0.0–Y0.15.
_6
3 2 1 0
10 10 10 10
F our -digit binary -coded
6 6 4 2 decimal ty pe of DIP s witch
8 1 8 1 8 1 8 1
X0.15 X0.0
F our -digit binary -coded deci mal value
T he instruction B IN is us ed to store
the binary value in D100.
T he instruction B CD is us ed to conver t
the value in D100 into the four- di gi t
binary- coded decimal value.
Y0.15 Y0.0
F our -digit binary -coded deci mal type

of sev en- segment display
6-82

Converting a binary integer into a binary
0202 D FLT P S, D

S         
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
D 

AS AS AS
Symbol
S ： Source device
Explanation 6_
1. This instruction converts the binary integer in S into the single-precision floating-point number and stores the
conversion result in D.
2. The operand S used in the instruction FLT cannot be the 32-bit counter, and not the device E.
3. The source device S used in the instruction FLT occupies one register, and D used in FLT occupies two registers.
4. The source device S used in the instruction DFLT occupies two registers, and D used in DFLT also occupies two
registers.
 When the absolute value of the conversion result is larger than the value that can be represented by the
maximum floating-point number, SM602 is ON, and the maximum floating-point number is stored in D.
 When the absolute value of the conversion result is less than the value that can be represented by the
minimum floating-point number, SM601 is ON, and the minimum floating-point number is stored in D.
 When the conversion result is zero, SM600 is ON.
6-83
Example 1
1. When X0.0 is ON, the instruction converts the binary integer in D0 into a single-precision floating-point number,
and stores the conversion result in (D13, D12).
2. When X0.1 is ON, the instruction converts the binary integer in (D1, D0) into a single-precision floating-point
number, and stores the conversion result in (D21, D20).
3. Suppose the value in D0 is 10. When X0.0 is ON, the instruction converts 10 into the single-precision floating-point
number 16#41200000, and then stores 16#41200000 in the 32-bit register (D13, D12).
4. Suppose the value in the 32-bit register (D1, D0) is 100,000. When X0.1 is ON, the instruction converts 100,000
into the single-precision floating-point number 16#47C35000, and stores 16#47C35000 in the 32-bit register (D21,
D20).
_6
Example 2
You can use the applied instructions to perform the following calculation.
 Convert the binary integer in D10 into the single-precision floating-point number, and store the conversion
result in (D101, D100).
 Convert the binary-coded decimal value in X0.0–X0.15 into the binary value, and store the conversion result
in D200.
 Convert the binary integer in D200 into the single-precision floating-point number, and store the conversion
result in (D203, D202).
 Divide the constant 615 by the constant 10, and store the quotient which is the single-precision floating-point
number in (D301, D300).
 Divide the single-precision floating-point number in (D101, D100) by the single-precision floating-point
number in (D203, D202), and store the quotient which is the single-precision floating-point number in (D401,
D400).
6-84
 Multiply the single-precision floating-point number in (D401, D400) by the single-precision floating-point
number in (D301, D300), and store the product which is the single-precision floating-point number in (D21,
D20).
 Convert the single-precision floating-point number in (D21, D20) into the decimal floating-point number, and
store the conversion result in (D31, D30).
 Convert the single-precision floating-point number in (D21, D20) into the binary integer, and store the
conversion result in (D41, D40).
(D10) (X0. 0~ X0.15) F61.5 Single-precis ion

(D21, D20) floating-point number
16-bit f our-digit
b inary b inary -coded
6
number dec imal number
1 2 5 4 7
(D31, D30)
Decimal float ing-point number
(D101,D100) (D200) B IN (D301,D300)
8
Single-precis ion S ingle-prec is ion (D41, D40)
floating-point numbe r 3 floating-point number 32-bit int eger
(D203, D202)
Single-pre cision
(D401,D400)
Single-precis ion
floating-point nu mber
6_
6-85
_6
6-86

Converting a 32-bit floating-point number
0204 D INT P S, D
into a binary integer

S        
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D      

AS AS AS
Symbol
S ： Source device
Explanation
1. This instruction converts a single-precision floating-point number in S into a binary integer, then rounds the binary
6_
floating-point number down to the nearest whole digit to becomes a binary integer, and then the instruction stores
the binary integer in D.
2. The source device S used in the INT instruction occupies two registers, and D used in INT occupies one register.
3. The source device S used in the DINT instruction occupies two registers, and D used in DINT also occupies two
registers.
4. The operand D used in the INT instruction cannot be the 32-bit counter, but not the device E.
5. The INT instruction is the opposite of the FLT instruction .
6. When the conversion result is zero, SM600 is ON.
7. During the conversion, if the floating-point number is rounded down to the nearest whole digit, SM601 is ON.
8. When the conversion result exceeds the range, SM602 is ON.
9. For the INT/IINTP instructions, the range of conversion result is between -32,768 and 32,767.
10. For the DINT/DINTP instructions, the range of conversion result is between -2,147,483,648 and 2,147,483,647.
6-87
Example
1. When X0.0 is ON, the instruction converts the single-precision floating-point number in (D1, D0) into a binary
integer, and stores the conversion result in D10. The instruction rounds the binary floating-point number down to
the nearest whole digit.
2. When X0.1 is ON, the instruction converts the single-precision floating-point number in (D21, D20) into a binary
integer, and stores the conversion result in (D31, D30). The instruction rounds the binary floating-point number
down to the nearest whole digit.
Additional remarks
_6
If the value in S exceeds the range of values that can be represented by the floating-point numbers, the instruction is not
executed, SM0 is ON, and the error code in SR0 is 16#2013.
6-88

Converting a 16-bit value into a 32-bit
0206 MMOV P S, D
value

S          
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S     
D  

AS AS －
Symbol
S ： Source device
Explanation
This instruction copies the data in the 16-bit device S to the 32-bit device D, and copies the sign bit from S to D.
Example 6_
When X0.0 is ON, the instruction copies the value of b15 in D4 to b15–b31 in (D7, D6), copies the values of b0–b14 to
the corresponding bits in (D7, D6), and ignores the bits b15–b30. The data in (D7, D6) is a negative value (same as the
source).
b 15 b0
0 Plus sign
1 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1 D4
1 Minus sign
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1 D7, D6
b 31 b 16 b 15 b0
6-89

Converting a 32-bit value into a 16-bit
0207 RMOV P S, D
value

S          
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D     

AS AS －
Symbol
S ： Source device
Explanation
This instruction copies the data in the 32-bit device S to the 16-bit device D, and copies the sign bit from b31 to b15 so
that the value in D4 is negative (same as b31).

_6
Example
When X0.0 is ON, the instruction copies the value of b31 in D7 to b15 in D4, copies the values of b0–b14 to the
corresponding bits in D4, and ignores bits b15–b30. The data in (D7, D6) is a negative value (same as the source).
b31 b16 b15 b0

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1 D7, D6
1 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1 D4
b15 b0
6-90

Converting a binary number into a Gray
0208 D GRY P S, D
code

S           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
D      

AS AS AS
Symbol
S ： Source device
Explanation
1. This instruction converts the binary value in the device specified by S into a Gray code, and stores the conversion 6_
result in the device specified by D.
2. Only the DGRY instruction can use the 32-counter, but not the device E.
3. The value in S should be within the available range.
The value in S in the 16-bit instruction must be between 0–32,767.
The value in S in the 32-bit instruction must be between 0–2,147,483,647.
Example
When X0.0 is ON, the instruction converts the constant 6513 into a Gray code, and stores the conversion result in Y1.0–
Y1.15.
6-91
b15 b0
K6513=H1971 0 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1
Y1.15 Y1.0
GRAY 6513 0 0 0 1 0 1 0 1 1 1 0 0 1 0 0 1
Y1
Additional remarks
If the value in S is less than 0, the operation error occurs, the instruction is not executed, SM0 is ON, and the error code
in SR0 is 16#2003.
_6
6-92

Converting a Gray code into a binary
0209 D GBIN P S, D
number

S           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
D      

AS AS AS
Symbol
S ： Source device
Explanation
1. This instruction converts the Gray code in the device specified by S into the binary value, and stores the 6_
conversion result in the device specified by D.
2. Use this instruction to convert the Gray code in the absolute position encoder which is connected to the input
terminal of the PLC to the binary value. The conversion result is stored in the specified register.
3. Only the DGBIN instruction can use the 32-counter, but not the device E.
4. The value in the device D must be within the available range.
The value in the device D in the 16-bit instruction must be between 0–32,767.
The value in the device D in the 32-bit instruction must be between 0–2,147,483,647.
6-93
Example
When X0.0 is ON, the instruction converts the Gray code in the absolute position encoder which is connected to the
inputs X0.0–X0.15 into the binary value, and stores the conversion result in D10.
X0
X0.15 X0.0
GRAY CODE 6513 0 0 0 1 0 1 0 1 1 1 0 0 1 0 0 1
b15 b0
H1971=K6513 0 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1
Additional remarks
If the value in S is less than 0, the operation error occurs, the instruction is not executed, SM0 is ON, and the error code
in SR0 is 16#2003.
_6
6-94
0210 D NEG P D Finding the two’s complement

D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D      

AS AS AS
Symbol
D ： Device in which the two’s

complement is stored
Explanation
1. This instruction converts a negative binary value into the two’s compliment.
2. Only the DNEG instruction can use the 32-bit counter. 6_

3. Generally, you use the NEGP and DNEGP pulse instructions.
Example 1
When X0.0 is switched from OFF to ON, this instruction inverts all bits in D0 (0 becomes 1, and 1 becomes 0), and 1 is
added to the result, and then stores the final value in the original register D10.
6-95
Example 2
Finding the two’s compliment of the negative value:
1. When the value of the 15th bit in D0 is 1, M0 is ON, and the value in D0 is a negative value.
2. When M0 is ON, the NEG instruction finds the two’s complement of the negative value in D0 (the corresponding
positive value).
Example 3
Finding the two’s compliment of the difference between two values:
_6
When X0.0 is ON,
1. If the value in D0 is greater than that in D2, M0 is ON.
2. If the value in D0 is equal to that in D2, M1 is ON.
3. If the value in D0 is less than that in D2, M2 is ON.
4. The value in D4 is a positive value.
6-96
Additional remarks
Binary representation of the value and its absolute value:
6_
1. Whether the data is a positive value or a negative value depends on the value of the highest bit in the register. If
the highest bit in the register is 0, the data is a positive value. If the highest bit is 1, the data is a negative value.
2. You can convert the negative value into its absolute value with the instruction NEG.
(D0)=2
0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
(D0)=1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
(D0)=0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
6-97

Reversing the sign of a 32-bit floating-
0211 FNEG P D
point number

D  DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D 

AS - AS
Symbol
D ： Device in which the sign of the value

is reversed
Explanation
This instruction reverses the sign of a single-precision floating-point number in D.
Example
Before the instruction is executed, the value in (D1, D0) is the negative value 16#AE0F9000. When X0.0 switches from
_6 OFF to ON, the instruction reverses the sign of the single-precision floating-point number in (D1, D0). In other words,
after the instruction is executed, the value in (D1, D0) is the positive value 16#2E0F9000.
Before the instruction is executed, the value in (D1, D0) is the positive value 16#2E0F9000. When X0.0 switches from
OFF to ON, the instruction reverses the sign of the single-precision floating-point number in (D1, D0). In other words,
after the instruction is executed, the value in (D1, D0) is the negative value 16#AE0F9000.
6-98

Converting a binary floating-point number
0212 FBCD P S, D
into a decimal floating-point number

S         
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Data source
Explanation
1. This instruction converts thee single-precision floating-point number in the register specified by S into the decimal
floating-point number, and stores the conversion result in the register specified by D.
6_
2. The floating-point operation in the PLC is based on single-precision floating-point numbers. Use the FBCD
instruction to convert a single-precision floating-point number into a decimal floating-point number.
When the absolute value of the conversion result is larger than the value that can be represented by the maximum
floating-point number, SM602 is ON.
When the absolute value of the conversion result is less than the value that can be represented by the minimum
When the conversion result is zero, SM600 is ON.
6-99
Example
When X0.0 is ON, the instruction converts the single-precision floating-point number in (D1, D0) into the decimal floating-
point number, and stores the conversion result in (D3, D2).
Binary floating-point number D1 D0 Real number: 23 bits; Ex ponent: 8 bi ts ; sign: 1 bit
Exponent Real number

[D 3]
Decimal fl oating-point number D3 D2 Mathem atic al form [D2] X 10
Additional remarks
If the value in S exceeds the range of values that can be represented by the floating-point numbers, the instruction is not
_6
6-100

Converting a decimal floating-point
0213 FBIN P S, D
number into a binary floating-point number

S       
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Data source
Explanation
1. This instruction converts the decimal floating-point number in the register specified by S into the single-precision
floating-point number, and stores the conversion result in the register specified by D.
6_
6.
2. Suppose the value in S is 1234, and the value in S+1 is 3. The instruction converts the value in S into 1.234x10
3. The value in D should be a single-precision floating-point number, and the values in S and S+1 represent the
decimal real number and the decimal exponent respectively.
4. Use the FBIN instruction to convert a decimal floating-point number into a single-precision floating-point number.
5. The real number of decimal floating-point numbers are from -9,999 to +9,999, the exponents of decimal floating-
point numbers are from -41 to +35. The practical range of decimal floating-point numbers in the PLC is between
±1175×10-41 and ±3402×10+35. When the operation result is zero, SM600 is ON.
6-101
Example 1
1. When X0.0 is ON, the instruction converts the decimal floating-point number in the register in (D1, D0) into the
single-precision floating-point number, and stores the conversion result is stored in (D3, D2).
Exponent Real number

[D 1]
Decimal fl oating-point number D1 D0 Mathematic al form [D0] X 10
Binary floating-point number D3 D2 Real number: 23 bits; Ex ponent: 8 bits ; sign: 1 bit
Example 2
1. Before the floating-point operation is performed, use the FLT instruction to convert the binary integer into a single-
precision floating-point number. Make sure the value to be converted is a binary integer before conversion. You
can use the FBIN instruction to convert the floating-point number into the single-precision floating-point number.
_6 2. When X0.0 is ON, K314 and K-2 are moved to D0 and D1 respectively, and then FBIN combines them into the
decimal floating-point number (3.14=314×10-2).
Additional remarks
If the real number part of the decimal floating-point number in S is not between -9,999 to +9,999, or if the exponent of the
decimal floating-point number in S is not between -41 to +35, the instruction is not executed, SM0 is ON, and the error
code in SR0 is 16#2013.
6-102

Converting binary numbers in blocks into
0214 BKBCD P S, n, D

S      
n        
D  DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS －
Symbol
S ： Data source
n ： Data length
Explanation
1. The instruction converts n pieces of data (the binary values) starting from S into the binary-coded decimal values, 6_
and stores the conversion results in D.
Example
When M1 is ON, the instruction converts the binary values in D0 and D1 into the binary-coded decimal values, and
stores the conversion results in D4 and D5.
6-103
Additional remarks
1. If n is less than 1, or larger than 256, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
2. If the devices specified by S+n-1 and D+n-1 exceed the range of possible devices, the instruction is not executed,
3. If the conversion result is not between 0–9,999, the instruction is not executed, and the error code in SR0 is
16#200D. The binary-coded decimal value is represented by the hexadecimal number, but one of digits is not in
between 0–9.
4. If S–S+n-1 overlaps D–D+n-1, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200C.
_6
6-104

Converting binary numbers in blocks into
0215 BKBIN P S, n, D

S      
n        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS －
Symbol
S ： Data source
n ： Data length
6_
Explanation
1. The instruction converts n pieces of data (the binary-coded decimal values) starting from S into the binary values,
and stores the conversion results in D.
2. The binary-coded decimal value in S must be between 0–9,999.
3. The operand n must be between 1 and 256.
Example
When M1 is ON, the instruction converts the binary-code decimal values in D0 and D1 into the binary values, and stores
the conversion results in D4 and D5.
6-105
Additional remarks
2. If the devices specified by S+n-1 and D+n-1 exceed the range of possible devices, the instruction is not executed,
3. If the data in S is not a binary-coded decimal, the instruction is not executed, and the error code in SR0 is
16#200D. The binary-coded decimal value is represented by the hexadecimal number, but one of digits is not
between 0–9.
4. If S–S+n-1 overlap D–D+n-1, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200C.
_6
6-106
0216 SCAL P S1, S2, S3, D Finding a scaled value (point-slope)

S1          
S2          
S3          
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
S3    
D    

AS AS AS
Symbol
S1 ： Data source
S2 ： Slope
S3 ： Offset
D ： Destination device 6_
Explanation
1. This instruction finds a scaled linear value for the number in S1 using the slope of the line in S2 and the offset in S3
to define the scaling factor, and stores the result in D.
2. The operation equation in the instruction is D=(S1×S2)÷1,000+S3
3. To get the values in S2 and S3, use the slope equation and the offset equation below first, and then round off the
results to the nearest whole digit. Enter the final 16-bit values into S2 and S3.
The slope equation: S2=[(Maximum destination value–Minimum destination value)÷(Maximum source value–
Minimum source value)]×1,000
The offset equation: S3=Minimum destination value–Minimum source value×S2÷1,000
6-107
The output curve is shown below:
Example 1
1. Suppose the values in S1, S2, and S3 are 500, 168, and -4 respectively. When X0.0 is ON, the SCAL instruction
calculates the scaled value, and stores the scaled value in D0.
2. For equation: D0=(500×168)÷1,000+(-4)=80
_6
Destination value
D
Slope=168
Offset=-4
Sourc e value
0 S 1=500
6-108
Example 2
1. Suppose the values in S1, S2, and S3 are 500, -168, and 534 respectively. When X0.0 is ON, the SCAL instruction
calculates the scaled value, and stores the scaled value in D10.
2. For the equation: D10=(500×-168)÷1,000+534=450
6_
Additional remarks
1. You must know the slope and the offset to use SCAL. If the slope and the offset are unknown, you can use the
SCLP instruction.
2. When the 16-bit instruction is performed, the value entered into S2 must be between –32,768 to 32,767. If the
value in S2 exceeds the range, use the SCLP instruction.
3. When the 32-bit instruction is performed, the value entered into S2 must be between -2,147,483,648 to
2,147,483,647. If the value in S2 exceeds the range, use the SCLP instruction.
4. When you use the slope equation, note that the maximum source value should be larger than the minimum source
value. However, the maximum destination value is not necessarily larger than the minimum destination value.
5. For the 16-bit instruction, if the value in D is larger than 32,767, the value stored in D is 32,767. If the value in D is
less than -32,768, the value stored in D is -32,768.
6. When the 32-bit instruction is performed, if the value in D is larger than 2,147,483,647, the value stored in D will be
2,147,483,6477. If the value in D is less than -2,147,483,648, the value stored in D will be -2,147,483,648.
6-109
0217 D SCLP P S1，S2，S3，D Finding a scaled value (two points)

S1            
S2       
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1     
S2     
D     

AS AS AS
Symbol
S1 ： Data source
S2 ： Parameter
_6
Explanation
1. This instruction finds a scaled linear value for the value in S1 using two points in S2 to define the scaling factor, and
stores the result in D.
3. The following table list the constant usage for the operand S1
32-bit instruction
Constant 16-bit instruction
SM685 ON SM685 OFF
Constant  X 
Hexadecimal  X 
Floating number X  X
The flag SM685 (whether to use floating point operation or not) can only be used for 32-bit instructions.
6 - 11 0
4. The operand S2 used in the 16-bit instruction is set as shown in the following table.
Device number Parameter Setting range
S2 Maximum source value -32,768 to 32,767
S2+1 Minimum source value -32,768 to 32,767
S2+2 Maximum destination value -32,768 to 32,767
S2+3 Minimum destination value -32,768 to 32,767
5. The operand S2 used in the 16-bit instruction occupies four devices.
6. The operand S2 used in the 32-bit instruction is set as shown in the following table.
Setting range
Device number Parameter
Integer Floating-point number
S2、S2+1 Maximum source value
S2+2、3 Minimum source value

-2,147,483,648 to The range of 32-bit
2,147,483,647 floating-point numbers

S2+4、5 Maximum destination value
S2+6、7 Minimum destination value
7. The operand S2 used in the 32-bit instruction occupies eight devices. 6_

8. If the values in the 32-bit instruction are floating-point numbers, set SM658 to ON. If the values are decimal
integers, set SM685 to OFF.
9. The operation equation in the instruction is:

D = [(S1–Minimum source value)×(Maximum destination value–Minimum destination value)]÷(Maximum source
value)+Minimum destination value
10. The operational relation between the source value and the destination value is:
y = kx+b
y=Destination value (D)
k=Slope=(Maximum destination value–Minimum destination value)÷(Maximum source value–Minimum source
value)
x=Source value (S1)
b=Offset =Minimum destination value–Minimum source value×Slope
6 - 111
The parameters above are substituted for y, k, x, and b in the equation y = kx+b to get the operation equation as
follows:
y=kx+b=D=kS1+b=Slope×S1＋Offset＝Slope×S1＋Minimum destination value–Minimum source
value×Slope=Slope×(S1–Minimum source value)＋Minimum destination value =(S1–Minimum source

value)×(Maximum destination value–Minimum destination value)÷(Maximum source value–Minimum source value)
＋Minimum destination value
11. If S1 is larger than the maximum source value, the maximum source value is the value in S1. If S1 is less than the
minimum source value, the minimum source value is the value in S1. The output curve is shown below.
_6
Example 1
1. Suppose the value in S1 is 500, the maximum source value in D0 is 3,000, the minimum source value in D1 is 200,
the maximum destination value in D2 is 500, and the minimum destination value in D3 is 30. When X0.0 is ON, the
SCLP instruction calculates the scale value and stores it in D10.
2. The operation equation: D10=[(500–200)×(500–30)]÷(3,000–200)+30=80.35
80.35 is rounded off to the nearest whole digit, and becomes 80. 80 is stored in D10.
6 - 11 2
Destinati on value
Maximum destination
value =500
6_
D
Minimum des ti nation
value =30 S 1=500
Sourc e value
0 Minimum Maximum
sourc e value =200 sourc e value =3000
Example 2
1. Suppose the value in S1 is 500, the maximum source value in D0 is 3,000, the minimum source value in D1 is 200,
the maximum destination value in D2 is 30, and the minimum destination value in D3 is 500. When X0.0 is ON, the
SCLP instruction calculates the scales value, and stores it in D10.
2. The operation equation: D10=[(500–200)×(30–500)]÷(3,000–200)+500=449.64
449.64 is rounded off to the nearest whole digit, and becomes 450. 450 is stored in D10.
6 - 11 3
_6
Example 3
1. Suppose the value in S1 is 500.0, the maximum source value in D0 is 3000.0, the minimum source value in D2 is
200.0, the maximum destination value in D4 is 500.0, and the minimum destination value in D6 is 30.0. When X0.0
is ON, SM685 is set to ON, the instruction DSCLP calculates the scale value and stores it in D10.
2. The operation equation: D10=[(500.0–200.0)×(500.0–30.0)]÷(3000.0–200.0)+30.0=80.35
80.35 is rounded off to the nearest whole digit, and becomes 80.0. 80.0 is stored in D10.
6 - 11 4
6_
Additional remarks
1. The value in S1 for 16-bit instructions must be between the minimum source value and the maximum source value;
that is, between -32,768 to 32,767. If the value exceeds the boundary value, the calculation uses the boundary
value.
2. The integer in S1 for 32-bit instructions must be between the minimum source value and the maximum source
value; that is, between -2,147,483,648 to 2,147,483,647. If the integer exceeds the boundary value, the calculation
uses the boundary value.
6 - 11 5
3. The floating-point number in S1 for 32-bit instructions must be between the minimum source value and the
maximum source value; that is, within the range of floating-point numbers. If the floating-point number exceeds the
boundary value, the calculation uses the boundary value.
4. Note that the maximum source value must be larger than the minimum source value. However, the maximum
destination value is not necessarily larger than the minimum destination value.
5. When the maximum source value is the same as the minimum source value, the instruction is be executed, SM0 is
ON and the error code in SR0 is 16#2012.
6. If you declare S2 for a 16-bit instruction in ISPSoft, the data type is ARRAY [4] of WORD.
7. If you declare S2 for a 32-bit instruction in ISPSoft, the data type is ARRAY [4] of DWORD.
_6
6 - 11 6
API Instruction Operand Description
0222 D SCLM P S1，S2，S3，S4，D Multi-point area ratio operation

S1    
S2      
S3     
S4     
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1     
S2    
S3    
S4    
D     

AS AS AS
Symbol
S1 : Data source
S2 : Number of multi-point areas
S3 : Comparison value in a multi-point area

6_
S4 : Conversion reference value
D : Operation result
6 - 11 7
Explanation
1. Only the 32-bit instruction can use HC devices but not E devices. The firmware of V1.04.00 and later for AS300 PLC
supports the instruction.
2. See the following table about data types that the operands S1, S3 and S4 correspond to. ( represents ‘Usable’. X
_6 represents ‘Unusable’.)
32-bit instruction
16-bit
Constant
instruction SM685 ON SM685 OFF
K  X 
16#  X 
F X  X
Note: SM685=ON (the floating point number operation) works for the 32-bit instruction only.
3. S1 is the data source. S2 is the number of multi-point areas and the value should be between 2 and 50. If the value
exceeds the range, the instruction will be executed automatically at the minimum value or maximum value. S3 is a
setting value for comparison in a multi-point area. S4 is a conversion reference value that a multi-point area
comparison value corresponds to, e.g. the number of areas, S2 is 10. Then S3 ~ S3+9 are comparison values in 10
areas. S4 ~ S4+9 are 10 corresponding conversion reference values.
4. The comparison order for multi-point areas is 0, 1, 2 …S2 –1. The comparison rule is S1 >= S3+0 and S1 < S3+1. If S1
value does not belong to an area, the comparison will move on to the next area. For example, S1 >= S3+1 and S1 <
S3+2, the comparison keeps going until the number of comparison times reaches S2 – 1.
6 - 11 8
5. The instruction compares areas in the order from small to large. Please design the value comparison of S3 area in
the order from small to large as well.
6. See the figure below for the conversion of multi-point area values. (Set the number of areas, S2 to 4.)
S4
S4+0
D
S4+1
S4+3
S4+2
S3
S3+0 S3+1 S3+2 S3+3
S1
7. If S1 value is between S3+0 and S3+1, the conversion formula: D =﹝ ( S1 – S3+0) x ( S4+1 – S4+0 ) / ( S3+1 –
S3+0 ) ﹞+ S4+0.
8. If S1 value does not belong to any specified area, the execution result in D is explained as below.
If S1 value > the last specified area, D will store the last conversion reference value of S4, e.g. if S1 value > S3+3 6_
value in the figure above, D=S4+3.
If S1 value < the first specified area, D will store the first conversion reference value of S4, e.g. if S1 value < S3+0
value in the figure above, D=S4+0.
9. If S3 and S4 of the16-bit instruction are declared on ISPSoft, the data type is ARRAY [S2] of WORD.
10. If S3 and S4 of the 32-bit instruction are declared on ISPSoft, the data type is ARRAY [S2] of DWORD (SM685=OFF)
or ARRAY [S2] of REAL (SM685=ON).
6 - 11 9
Example
The comparison values of S3 for multi-point areas are given as follows.

Device D100 D101 D102 D103
Content 100 200 300 400
The corresponding conversion reference values of S4 are given as follows.
Device D200 D201 D202 D203
Content 4000 3000 1500 2000
Here is the explanation about the value in D2 obtained through a conversion based on the data resource D0.
Set D0=10,
Since D0<D100 (in the first area), D2=D200=4000 (the first conversion reference value)
Set D0=K150,
D0 value is in between (D100, D101) = (100, 200) and the corresponding reference value is (D200, D201) =
(4000, 3000)
Therefore,
D2= (150-100)* (3000-4000) / (200-100) +4000=3500
Set D0=450
Since D0>D103 (in the last area), D2=D203=2000 (the last conversion reference value)
_6 Set D0=K250
D0 value is between (D101, D102) = (200, 300) and the corresponding reference value is (D201, D202) =
(3000, 1500).
Therefore,
D2= (250-200) *(1500-3000) / (300-200) +3000=2250
Set D0=K350
D0 is between (D102, D103) = (300, 400) and the corresponding reference value is (D202, D203) = (1500,
2000)
Therefore,
D2= (350-300) * (2000-1500) / (400-300) +1500=1750
6-120
Ch a pt er 6 Ap p l i ed I ns t r uc t i ons
6.4 Data Transfer Instructions

6.4.1 List of Data Transfer Instructions
The following table lists the Data Transfer instructions covered in this section.
Instruction code
API Pulse instruction Function
16-bit 32-bit
0300 MOV DMOV  Transferring data
0302 $MOV –  Transferring a string
0304 BMOV DBMOV  Transferring data in blocks
0305 NMOV DNMOV  Transferring data to multiple devices
0306 XCH DXCH  Exchanging data
0307 BXCH –  Exchanging data in blocks
0308 SWAP DSWAP  Exchanging the high byte with the low byte
0309 SMOV –  Transferring digits in blocks
0310 MOVB –  Transferring bits in blocks
6_
6-121
6.4.2 Explanation of Data Transfer Instructions
0300 D MOV P S, D Transferring data

S            
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S       
D       

AS AS AS
Symbol
S ： Data source
_6
Explanation
1. This instruction transfers the data in S to D.
2. You must use a 32-bit instruction when the data in S is a floating-point number.
Example
1. To transfer 16-bit data, use MOV.
 When X0.0 is OFF, the data in D0 is unchanged. When X0.0 is ON, the instruction transfers 10 to the data
register D0.
 When X0.1 is OFF, the data in D10 is unchanged. When X0.1 is ON, the instruction transfers the current
value of T0 to the data register D10.
6-122
2. For 32-bit data, use DMOV.
 When X0.2 is OFF, the data in (D31, D30) and (D41, D40) is unchanged. When X0.2 is ON, the instruction
transfers the current value in (D21, D20) to (D31, D30), and transfers the current value of HC0 to (D41,
D40).
3. For floating-point numbers, use DMOV.
 When X0.3 is OFF, the data in (D51, D50) is unchanged. When X0.3 is ON, the instruction converts the
floating-point number 3.450 into a binary floating-point number, and transfers the conversion result is to
(D51, D50).
6_
6-123
0302 $MOV P S, D Transferring a string

S       
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS AS －
Symbol
S ： Data source
Explanation
1. This instruction transfers the string in S to D, and adds the code 16#00 to the end of the string.
_6 2. When the operand S is not a string, the instruction adds the code 16#00 to the end of the data transferred.
3. When the ending code16#00 cannot be found in S for 256 characters in a row or even beyond the device range,
the instruction is not executed; SM0 is ON and the error code in SR0 is 16#200E.
4. When the operand S is not a string and the instruction is executed, the string starting with the data in the device
specified by S (including 16#00) is transferred to D. When the instruction is not executed, the data in D is
unchanged.
5. If D is not sufficient to contain the string composed of the values in S, the instruction is not executed, SM0 is ON,
and the error code in SR0 is 16#2003.
6. Suppose the operand S is not a string. When the instruction is executed and the first character in S is the code
16#00, 16#00 is still transferred to D.
6-124
7. When 16#00 appears in the low byte, the execution of the instruction is as follows.
Before the instr uction is executed:

b15~b8 b7~b0 B15~b8 b7~b0
S 16#31 16#30 D 16#38 16#39
S+1 16#33 16#32 D+1 16#36 16#37
S+2 16#35 16#34 D+2 16#34 16#35
S+3 16#30 16#00 D+3 16#32 16#33
After the instruction is executed:

b15~b8 b7~b0 b15~b8 b7~b0
S 16#31 16#30 D 16#31 16#30
S+1 16#33 16#32 D+1 16#33 16#32
S+2 16#35 16#34 D+2 16#35 16#34
S+3 16#30 16#00 D+3 16#00 16#00
16#30 in the high byte 16#32 in the high byte

is not tr ansfer red. turns into 16#00.
8. When 16#00 appears in the high byte, the execution of the instruction is as follows. The transfer stops when the
code 16#00, leaving the remainder of D unchanged.
Before the instr uction is executed:

b15~b8 b7~b0 b15~b8 b7~b0
S 16#31 16#30 D 16#38 16#39
6_
S+ 1 16#33 16#32 D+1 16#36 16#37
S+ 2 16#00 16#34 D+2 16#34 16#35
S+ 3 16#37 16#36 D+3 16#32 16#33
After the instr uction is executed:

b15~b8 b7~b0 b15~b8 b7~b0
S 16#31 16#30 D 16#31 16#30
S+ 1 16#33 16#32 D+1 16#33 16#32
S+ 2 16#00 16#34 D+2 16#00 16#34
S+ 3 16#37 16#36 D+3 16#32 16#33
6-125
9. When S overlaps D and the device number of S is less than the device number of D, the transfer of the data to D
starts form the ending code 16#00.
Before the instruction is executed:

b15~b8 b7~b0 b15~b8 b7~b0
D0 16#31 16#30 D1 16#33 16#32
D1 16#33 16#32 D2 16#35 16#34
D2 16#35 16#34 D3 16#30 16#00
D3 16#30 16#00 D4 16#38 16#37
After the instruction is executed:

b15~b8 b7~b0 b15~b8 b7~b0
D0 16#31 16#30 D1 16#31 16#30
D1 16#33 16#32 D2 16#33 16#32
D2 16#35 16#34 D3 16#35 16#34
D3 16#30 16#00 D4 16#00 16#00
Example 1
Suppose the data in S is the string “1234” (even number of bytes). When X0.0 is enabled, the data 1234 and the ending
code 16#00 is transferred to D0–D3 and 16#00 is added to the high byte in D, as follows.
_6
The operand S:
String ‘1’ ‘2’ ‘3’ ‘4’
Hexadecimal
16#31 16#32 16#33 16#34
value
After the instruction is executed, the data in D is as follows.
Device High byte Low byte Note
D0 16#32 16#31 ‘1’=16#31; ‘2’=16#32
D1 16#34 16#33 ‘3’=16#33; ‘4’=16#34
The ending code 16#00 is in the low byte.

D2 16#00 16#00
16#00 is automatically added in the high byte.
D3 Unchanged Unchanged
6-126
Example 2
Suppose the data in S is the string “12345” (odd number of bytes). When X0.0 is enabled, the data 12345 is transferred
to D0–D3 as follows.
The operand S:
String ‘1’ ‘2’ ‘3’ ‘4’ ‘5’
Hexadecimal
16#31 16#32 16#33 16#34 16#35
value
After the instruction is executed, the data in the operand D is as follows.
D0 16#32 16#31 ‘1’=16#31; ‘2’=16#32
D1 16#34 16#33 ‘3’=16#33; ‘4’=16#34
D2 16#00 16#35 The ending code 16#00 is in the high byte.
D3 Unchanged Unchanged 6_
Example 3
When the data in S is not a string and the ending code 16#00 appears in the low byte, the execution of the instruction is
as follows.
The operand S:
D100 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D101 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D102 16#35 16#34 ‘5’=16#35; ‘4’=16#34
D103 16#30 16#00 ‘0’=16#30; 16#00 is the ending code.
6-127
D0 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D1 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D2 16#35 16#34 ‘5’=16#35; ‘4’=16#34

D3 16#00 16#00
Example 4
When the data in S is not a string and the ending code 16#00 appears in the high byte, the execution of the instruction is
as follows.
The operand S:
_6 D100 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D101 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D102 16#00 16#34 16#00 is the ending code. ‘4’=16#34
D103 16#37 16#36 ‘7’=16#37; ‘6’=16#36
D0 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D1 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D2 16#00 16#34 16#00 is the ending code. ‘4’=16#34
6-128
Example 5
When S overlaps D, and the device number of S is less than the device number of D, the transfer of the data to D starts
from the ending code 16#00.
The operand S:
D0 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D1 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D2 16#35 16#34 ‘5’=16#35; ‘4’=16#34
D3 16#30 16#00 ‘0’=16#30; 16#00 is the ending code.
D4 16#38 16#37 ‘8’=16#38; ‘7’=16#37
After the instruction is executed, the data in D is as follows. 6_
D1 16#31 16#30 ‘1’=16#31; ‘0’=16#30
D2 16#33 16#32 ‘3’=16#33; ‘2’=16#32
D3 16#35 16#34 ‘5’=16#35; ‘4’=16#34

D4 16#00 16#00
6-129
0303 D CML P S, D Inverting data

S           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    

AS AS AS
Symbol
S ： Data source
Explanation
_6 1. This instruction inverts all bits in S; that is, 0 becomes 1, and 1 becomes 0, and stores the inversion result in D. If
the data in S is a constant, the instruction converts it into a binary value.
Example 1
When X0.0 is ON, the instruction inverts all bit in D1, and stores the conversion result in Y0.0–Y0.15.
b 15 b3 b2 b1 b0
D1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
Sign bi t (0: P os itive s ign; 1: Negativ e si gn)
Y0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Inversi on resul t
6-130
Example 2
The circuits below can be represented with the CML instruction.
6_
6-131
0304 D BMOV P S, D, n Transferring data in blocks

S       
D     
n         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： Data source
n ： Data length
_6
Explanation
1. This instruction transfers n pieces of data in a block starting from the device specified by S to the devices starting
from the device specified by D.
2. The value in n must be between 1–256.
4. To prevent overlapping the source and the destination, the instruction transfers the data in the following way (using
the 16-bit instruction as an example).
When the device number of S is larger than the device number of D, the data is transferred in the order from  to
.
6-132
1
D 20 D 19
2
D 21 D 20
3
D 22 D 21
When the device number of S is less than the device number of D, the data is transferred in the order from  to .
1
D 19 D 20
2
D 20 D 21
3
D 21 D 22
Example 1
When X0.0 is ON, the instruction transfers the data in D0–D3 to D20–D23.
D0 D20
D1 D21
N=4
D2 D22
D3 D23
6_
Example 2
To prevent overlapping the source and the destination, the data is transferred in the following way.
1. When the device number of S is larger than the device number of D, the data is transferred in the order from  to
.
1
D20 D19
2
D21 D20
3
D22 D21
6-133
2. When the device number of S is less than the device number of D, the data is transferred in the order from  to .
1
D10 D11
2
D11 D12
3
D12 D13
Additional remarks
1. If D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
2. If S+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
_6
6-134
0305 D NMOV P S, D, n Transferring data to multiple devices

S         
D     
n   DWORD       
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： Data source
n ： Data length
6_
Explanation
1. This instruction transfers the data in S to the n devices starting from the device specified by D. When the
instruction is not executed, the data in D is unchanged.
3. The value in n in the NMOV instruction must be between 1–256.
S S D
S D+1
S D+2 N=5
S D+3
S D+4
6-135
Example
When M0 is ON, 100 is transferred to D0-D9.
Additional remarks
1. If D-D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
2. If the value in n in the 16-bit instruction is not between 1–256, the instruction is not executed, SM0 is ON, and the
_6
6-136
0306 D XCH P S1, S2 Exchanging data

S1      
S2      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    

AS AS AS
Symbol
S1 ： Data to exchange
Explanation 6_
1. This instruction exchanges the data in the device specified by S1 with the data in the device specified by S2.
Example 1
When X0.0 is switched from OFF to ON, the instruction exchanges the data in D20 with the data in D40.
Before the instruction After the instruction

is executed: is executed:
D 20 1 20 40 D 20
D 40 40 1 20 D 40
Example 2
When X0.0 switches from OFF to ON, the instruction exchanges the data in D100 with the data in D200.
Before the instruction After the instruction
is executed: is executed:
D 10 0 9 8 D 10 0
D 10 1 20 40 D 10 1
D 20 0 8 9 D 20 0
D 20 1 40 20 D 20 1
6-137
0307 BXCH P S1，S2，n Exchanging data in blocks

S1    
S2    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
n  

AS AS －
Symbol
n ： Data length
_6
Explanation
1. This instruction exchanges the data in S1–S1+n-1 with the data in S2–S2+n-1.
S1 S1 +1 S1 +2 .... S1 +n- 1 S2 S2 +1 S2 +2 .... S2 +n- 1
S1 S1 +1 S1 +2 .... S1 +n- 1 S2 S2 +1 S2 +2 .... S2 +n- 1
6-138
Example
When X0.0 is ON, the instruction exchanges the data in D10–D14 with the data in D100–D104.
D10 D11 D12 D13 D14 D100 D101 D102 D103 D104
1 2 3 4 5 16 17 18 19 20
After the i nstruction is executed
D10 D11 D12 D13 D14 D100 D101 D102 D103 D104
16 17 18 19 20 1 2 3 4 5
Additional remarks
1. If S1+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
2.
6_
If S2+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in n is not between 1–256, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
6-139

Exchanging the high byte with the low
0308 D SWAP P S
byte

S  DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    

AS AS AS
Symbol
S ： Data source
Explanation
1. The 16-bit instruction exchanges the data in the low byte in S with the data in the high byte in S.
_6 2. The 32-bit instruction exchanges the data in the low byte of the high word in S with the data in the high byte of the
high word in S, and exchanges the data in the low byte of the low word in S with the data in the high byte of the low
word in S.
Example 1
When X0.0 is ON, the instruction exchanges the data in the low byte in D0 with the data in the high byte in D0.
D0
High byte Low byte
6-140
Example 2
When X0.0 is ON, the instruction exchanges the data in the low byte in D11 with the data in the high byte in D11, and
exchanges the data in the low byte in D10 with the data in the high byte in D10.
D11 D10
High byte Low byte High byte Low byte
6_
6-141
0309 SMOV P S, m1, m2, D, n Transferring digits in blocks

S        
m1        
m2        
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S  
m1  
m2  
D  
n  

AS AS －
Symbol
S ： Data source
m1 ： Start digit to transfer from the source device

_6 m2 ： Number of digits to transfer
Start digit where the source data is stored in
n ：
the destination device
Explanation
1. This instruction allocates and combines data. The instruction transfers m2 digits of the number starting from the
m1th digit of the number in S to the m2 digits of the number starting from the nth digit of the number in D.
2. The value in m1 must be between 1–4. The value in m2 must be between 1–m1. The value in n must be between
m2–4 (the instruction treats four bits as a unit.)
3. When SM605 is OFF, the data in S are binary-coded decimal numbers.
6-142
D10 (16- bit binary number)

Conversi on
3 2 1 0
10 10 10 10 D10 (4- digit binary -coded deci mal)
Unchanged Unchanged T ransferri ng the digits

3 2 1 0
10 10 10 10 D20 ( 4- digit binary -coded deci mal )
Conversi on
D20 ( 16- bit binary number )
Suppose the number in S is K1234, and the number in D is K5678. After the instruction is executed, the number in
S is 1234, and the number in D is 5128.
4. When SM605 is ON, the data involved in the instruction is binary numbers.
th rd nd st
4 digit 3 digit 2 digit 1 digit
T ransferring the digits

th rd nd st
Unchanged Unchanged
Suppose the number in S is 16#1234, and the number in D is 16#5678. After the instruction is executed, the
number in S is 16#1234, and the number in D is 16#5128.
Example 1 6_
1. When SM605 is OFF, the data in S are binary-coded decimal numbers. When X0.0 is ON, the instruction transfers
two digits of the decimal number starting from the fourth digit of the decimal number (the digit in the thousands
place of the decimal number) in D10 to the two digits of the decimal number starting from the third digit of the
decimal number (the digit in the hundreds place of the decimal number) in D20. After the instruction is executed,
the digits in the thousands place of the decimal number (103) and the ones place of the decimal number (100) in
D20 are unchanged.
2. When the binary-code decimal number is not between 0–9,999, the instruction is not executed, SM0 is ON, and the
error code in SR0 is 16#200D.
6-143
D10 (16- bit binary number)

Conversi on
3 2 1 0
10 10 10 10 D10 (4- digit binary -coded deci mal)
Unchanged Unchanged T ransferri ng the digits

3 2 1 0
10 10 10 10 D20 ( 4- digit binary -coded deci mal )
Conversi on
Suppose the number in D10 is 1234, and the number in D20 is 5678. After the instruction is executed, the number
in D10 is unchanged, and the number in D20 is 5128.
_6 Example 2
When SM605 is ON, the data are binary numbers. The SMOV instruction transfers the digit composed of four bits. The
instruction does not transform the data into binary-coded decimal numbers.
6-144
th rd nd st
T ransferring the digits

th rd nd st
Unchanged Unchanged
Suppose the number in D10 is 16#1234, and the number in D20 is 16#5678. After the instruction is executed, the
number in D10 is unchanged, and the number in D20 is 16#5128.
Example 3
1. You can use the instruction to combine the values of the DIP switches that are connected to the input terminals
whose numbers are not consecutive.
2. The two digits of the value of the DIP switch at the right are transferred to the two digits of the number which start
from the second digit of the number in D2, and the one digit of the value of the DIP switch at the left is transferred
to the first digit of the number in D1.
3. You can use the SMOV instruction to transfer the first digit of the number in D1 to the third digit of the number in
D2. In other words, the two DIP switches can be combined into one DIP switch by means of the SMOV instruction.
2 1 0
10 10 10
6_
6 4 2
8 1 8 1
8 1
X0.3~X0.0 X1.15~X1.0
PLC
6-145
Additional remarks
1. Suppose the data are binary-coded decimal numbers. If the number in S is not between 0–9999, or if the number
in D is not between 0–9999, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200D.
_6 2. If m1 is less than 1, or if m1 is larger than 4, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#200B.
3. If m2 is less than 1, or if m2 is larger than m1, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#200B.
4. If n is less than m2, or if n is larger than 4, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
6-146

0310 MOVB P S, n, D Transferring bits in blocks

S         
n          
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
n  
D 

AS AS －
Symbol
S ： Data source
n ： Data length
Explanation
1. This instruction transfers n pieces of data in devices starting from the device specified by S to the devices starting
from the device specified by D. 6_
2. When S is T, C or HC, the instruction transfers only the state of the device, but does not transfer the current value
of the device.
3. The value in n must be between 1–256. When n not between 1–256, the instruction is not executed, SM0 is ON,
and the error code in SR0 is 16#200B.
Example
When X0.0 is ON, the instruction transfers the data in D0.8–D0.13 to D1.2–D1.7.
6-147
Additional remarks
16#2003.
16#2003.
_6
6-148
6.5 Jump Instructions

6.5.1 List of Jump Instructions
The following table lists the Jump instructions covered in this section.

API Function
0400 CJ –  Conditional jump
0401 JMP – – Unconditional jump
0402 GOEND – – Jumping to the end of the program
6_
6-149
6.5.2 Explanation of Jump Instructions
0400 CJ P S Conditional jump

S
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type

AS AS －
Symbol
S ： Jump destination
Explanation
1. This instruction jumps from the current program execution to a label (destination) in a different part of the program
in the PLC. You specify the label (pointer) in S. You can use the CJ or CJP instruction to shorten the scan time. You
_6
can also use the CJ or CJP instruction when using a dual output.
2. If the program specified by the jump destination (label) is prior to the CJ instruction, the watchdog timer error
occurs, and the PLC stops running the program. Use this instruction carefully.
3. You can specify the same label repeatedly with the multiple different CJ instructions.
4. When the instruction is executed, the actions of the devices are as described below.
 The state of Y, the state of M, and the state of S remain the same as before the execution of the jump.
 The timer keeps counting and when it reaches the time setting value, the program drives the output T-coil.
 For more information on the MC and MCR instructions, refer to Example 2 below.
 The general applied instructions are not executed.
Example 1
1. When X0.0 is ON, the program execution jumps from NETWORK 1 to LABEL1 (NETWORK 3) and skips
NETWORK 2.
6-150
2. When X0.0 is OFF, the execution of the program goes from NETWORK 1 to NETWORK 2 to NETWORK 3 in
sequence, and the CJ instruction is not executed.
Example 2
1. You can use the CJ instruction between the MC and the MCR instructions in the five conditions below.
(a) The execution of the program jumps from the part of the program outside one MC/MCR loop to the part of
the program outside another MC/MCR loop.
(b) The execution of the program jumps from the part of the program outside the MC/MCR loop to the part of the
program inside the MC/MCR loop.

6_
(c) The execution of the program jumps from the part of the program inside the MC/MCR loop to the part of the
program inside the MC/MCR loop.
(d) The execution of the program jumps from the part of the program inside the MC/MCR loop to the part of the
program outside the MC/MCR loop.
(e) The execution of the program jumps from the part of the program inside one the MC/MCR loop to the part of
the program inside another the MC/MCR loop.
2. When the PLC executes an MC instruction, it puts the previous state of the switch contact onto the top of the stack
inside the PLC. The stack is controlled by the PLC, and cannot be changed. When the PLC executes the MCR
instruction, the PLC pops the previous state of the switch contact from the top of the stack. Under the conditions
listed in (b), (d), and (e) above, the number of times the items are pushed onto the stack may be different from the
number of times the items are popped from the stack. When this situation occurs, at most 32 items can be pushed
onto the stack; items can be popped from the stack until the stack is empty. Therefore, when you use CJ or CJP
with MC and MCR, be careful of how the program pushes items onto the stack and pops items from the stack.
6-151
_6
6-152
Example 3
The states of the devices are listed below.
State of the contact State of the contact during the State of the output coil during the
Device before the execution execution of CJ execution of CJ
of CJ M0=OFF M0=ON M0=ON
M1, M2, and M3 are M1, M2, and M3 switch from OFF
Y0.1*1, M20, and S1 are OFF.
OFF. to ON.
Y, M, and S
M1, M2, and M3 M1, M2, and M3 switch from ON
Y0.1*1, M20, and S1 are ON.
are ON. to OFF.
M4 is OFF. M4 switches from OFF to ON. The timer is not enabled.
The timer keeps counting and when

Timer
M4 is ON. M4 switches from ON to OFF the timer setting value is reached, it
drives the output T-coil.
M6 is OFF. M6 switches from OFF to ON. ST1 is not enabled.
The accumulative timer keeps

Accumulative
counting and when the timer setting
timer M6 is ON. M6 switches from ON to OFF.
value is reached, it drives the output
T-coil.
M7 and M10 are

6_
M10 is ON/OFF. The counter is not enabled.
OFF.
Counter
M7 is OFF. M10 is C0 stops counting. When M0 switches
M10 is ON/OFF.
ON/OFF. OFF, C0 keeps counting.
The applied instruction is not

M11 is OFF. M11 switches from OFF to ON
executed.
Applied
instruction The applied instruction is skipped (not
M11 is ON. M11 switches from ON to OFF
executed).
*1:Y0.1 is a dual output. When M0 is OFF, Y0.1 is controlled by M1. When M0 is ON, Y0.1 is controlled by M12.
6-153
_6
6-154
Additional remarks
6_
Refer to the ISPSoft User Manual for more information on the use of labels (pointers) with Jump instructions.
6-155
0401 JMP S Unconditional jump

S DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type

－ AS －
Symbol
S ： Jump destination
Explanation
1. This instruction causes the execution of the program to jump to the part of the program specified by the label in S
(pointer) without any condition.
_6 2. If the program specified by the label is prior to the instruction JMP, the watchdog timer error occurs, and the PLC
stops running the program. Use this instruction carefully.
3. Refer to the CJ instruction (API 400) for more information on the states of devices while executing this instruction.
4. Refer to the ISPSoft User Manual for more information on the use of labels (pointers) with Jump instructions.
6-156
0402 GOEND ─ Jumping to END

－ AS －
Symbol
Explanation
1. This instruction causes program execution to jump to END in the program.
2. Function blocks and interrupt tasks do not support the GOEND instruction. You cannot use the instruction between
the FOR instruction and the NEXT instruction.
3. When the PLC executes the GOEND instruction, the instructions skipped are not executed, the data in all devices
is unchanged, and the states of all devices are also unchanged.
6_
6-157
6.6 Program Execution Instructions

6.6.1 List of Program Execution Instructions
The following table lists the Program Execution instructions covered in this section.

API Function
0500 DI – – Disabling the interrupt function
0501 EI – – Enabling the interrupt function
0503 EIX – – Disabling a specific interrupt
0504 DIX – – Enabling a specific interrupt
_6
6-158
6.6.2 Explanation of Program Execution Instructions
0500 DI － Disabling the interrupt function

－ AS －
Symbol
Explanation
Refer to the EI instruction (API 0501) for more information.
6_
6-159
0501 EI － Enabling the interrupt function

－ AS －
Symbol
Explanation
1. Use the EI instruction to enable interrupt tasks in a program (refer to next page for more information on tasks).
2. You can use the interrupt task between the EI instruction and the DI instruction in a program. You can choose not
to use the DI instruction when there is no part of the program in which the interrupt is disabled.
3. During the execution of one interrupt task, a new interrupt generated is not executed, but is stored. After the
execution of the present interrupt task is complete, the next interrupt task is executed. For example, during the
execution of I0 (by trigged order #1), 2 new I0s (by trigged order #2, by trigged order #3) are generated, only by
trigged order #2 I0 will be stored for later execution. by trigged order #3 IO is not stored for execution.
4. When several interrupts occur, the interrupt task with the highest priority is executed first. When several interrupts
_6 occur simultaneously, the interrupt task with the smallest pointer number is executed first.
5. When the interrupt task occurs between DI and EI, it cannot be executed, and the interrupt request is ignored. It is
suggested that you not use the instruction DI to disable interrupts while PLC is running.
6. When the immediate I/O signal is required in the execution of the interrupt task, you can use the REF instruction or
the device DX/DY in the program to refresh the state of the I/O.
7. Every interrupt number has a temporary function that can be masked. See below for the list of interrupt numbers.
Example:
 Set up the timed I601 interrupt task to 500ms in HWCONFIG in ISPSoft.
 When the PLC runs the program Cyclic_0, it scans the EI instruction, enables interrupt tasks, and then executes
the I601 interrupt task. When the interrupt task execution is complete, the main program is executed.
 When M0 is ON, the I601 timer interrupt task is disabled.
 When M1 is ON, the I601 timer interrupt task is enabled.
6-160
 When M2 is ON, the SR632 is 0 and the I601 timer interrupt task is disabled.
 When M3 is ON, the SR632 is 1 and the I601 timer interrupt task is enabled.
The program Cyclic_0:
6_
The interrupt task:
6-161
Timer interrupts in a diagram:

Execute the i ns truction D IX
to dis able i nterrupt
M0 =O N
Ex ecute the ins truc ti on E IX
to e nable i nterrupt
M1 =O N
SR 632=0
interr upt d isabled
M2 =O N
SR632=1
interrupt enabled
M3 =O N
0 .5
Y 0.0 0 .5 s ec
se c
Additional remarks
There are 7 types of interrupt tasks:
1. External interrupts (I000–I115)
I000 specifies that the input X0.0 is falling edge triggered.
I100 specifies that the input X0.0 is rising edge triggered.

_6
The rest can be done in the same manner.
2. Hardware high-speed comparison interrupts (I200–I253)
This type of interrupts can be further divided into 6 groups. Each group corresponds to a hardware high-speed
counter (refer to the DCNT instruction API 1003 for more information). Each group has with 4 interrupt numbers (refer
to the DHSCS instruction API 1005 for more information). For example, the interrupt numbers for the first group are
I200–I203, and for the second group are I210–I213.
3. Software high-speed comparison interrupts (I260–I267)
There are 8 interrupts for software high-speed comparisons and these 8 interrupts are shared with 8 high-speed
counters.
4. Communication interrupts
You can use the communication interrupt as the RS instruction; that is, receiving a specific character triggers the
interrupt, or you can use it as a general interrupt. Refer to the COMRS instruction (API1812) for more information.
6-162
COM1: I300
COM2: I302
Card 1: I304
Card 2: I306
5. Extension module interrupts (I400–I431)
Each module has one interrupt. You can set up 1 interrupt service for each extension module.
6. High-speed output interrupts (I500–I519)
When the pulse output is complete, the interrupt request is sent. The interrupts (I500–I505) for the completing the
execution of the positioning instruction work with special devices (SM) to activate the interrupt service. For example,
when the DDRVI instruction completes the execution of the first axis, the interrupt request I500 is sent; you can set
SM471 to ON to activate the interrupt service. The interrupts (I510–I519) for the completing the execution of the
position planning table instruction work with the TPO instruction. When the pulse output is complete, the interrupt
request is sent.
7. Timer interrupts (I601–I604)
Set the timer interrupts set in HWCONFIG.
6_
For the timer interrupts I601–I603: The default value is 10 milliseconds (unit: 1ms) (1–2000 milliseconds).
For the timer interrupts I604: The default value is 1 milliseconds (unit: 0.1ms) (0.1–200 milliseconds).
The complete list of interrupt numbers, descriptions and the maskable interrupts (SR) are listed in the following table.
Interrupt Maskable interrupts

Description Bit No.
number SR
I000 External interrupt: input X0.0 is falling edge triggered. 0
I004 External interrupt: input X0.4 is falling edge triggered. SR623 4
6-163

Description Bit No.
number SR
I100 External interrupt: input X0.0 is rising-edge triggered. 0

SR624
_6
High-speed comparison interrupt 1 for the hardware high-

0
I200 speed counter 1

1
SR625
2

3
6-164

Description Bit No.
number SR

4

5

6

7

8

9

10

11

12
6_
13

14

15

0

1
SR626
2

3
6-165

Description Bit No.
number SR

4

5

6

7
High-speed comparison interrupt 1 for the software high-

0
I260 speed counter

1
I261 speed counter

2
I262 speed counter

3
I263 speed counter
SR627
_6 I264 speed counter
4

5
I265 speed counter

6
I266 speed counter

7
I267 speed counter
Receiving a specific word triggers communication interruption

0
I300 in COM1
I301 Reserved 1

2
I302 in COM1 SR628
I303 Reserved 3

4
I304 in function card 1
I305 Reserved 5
6-166

Description Bit No.
number SR

6
I306 in function card 2
I307 Reserved 7
High-speed output interrupt: the 1st axis positioning

0
I500 instruction completes
High-speed output interrupt: the 2nd axis positioning

1
High-speed output interrupt: the 3rd axis positioning

2
SR629
High-speed output interrupt: the 4th axis positioning
3

4

5
High-speed output interrupt 1: the position planning table

0

6_
1

2

3

SR630 4

5

6

7

8
6-167

Description Bit No.
number SR

9
I601 Timer interrupts 1 (unit 1ms) 0

SR632
I604 Timer interrupts 1 (unit 0.1ms) 3
Note: When several interrupts occur simultaneously, the interrupt task whose pointer number is smallest is executed
first. The PLC completes the on-going interrupt, and then execute other interrupts according to their pointer numbers.
For example, during the execution of I400 interrupt, if I500 and I300 occur simultaneously, the PLC executes the I300
interrupt (smaller pointer number) after executing the I400 interrupt.
_6
6-168
0503 EIX S Enabling a specific interrupt

S 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type

－ AS －
Symbol
S ： Data source
Explanation
1. The data source S can only contain a decimal number, and the number must be an interrupt number. If the number
is not an interrupt number, the instruction is not executed and no warning is shown. For example, use EIX500 in S
when you want to enable the I500 interrupt. Refer to the interrupt number list in the explanation of the EI
instruction.
6_
2. The default for interrupt tasks in the AS Series is enabled. If you use the DIX instruction to disable the interrupts,
you must use the EIX instruction to enable the interrupts.
3. You can use this instruction to enable the interrupt tasks in SR623–SR634.
4. If this instruction is not executed, then the contents of SR623–SR634 determine whether an interrupt task is
performed or not.
5. Refer to the examples for the EI instruction (API 0501) for more information.
6-169
0504 DIX S Disabling a specific interrupt

S DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type

－ AS －
Symbol
S ： Data source
Explanation
1. The data source S can contain only decimal numbers, and the number must be an interrupt number. If the number
in S is not an interrupt number, the instruction is not executed and no warning is shown. For example, use DIX500
when you want to disable the I500 interrupt. Refer to the interrupt number list in the explanation of the EI
instruction.
_6 2. The default for interrupt tasks in the AS Series is enabled. Use the DIX instruction to disable the interrupts.
3. You can use this instruction to disable the interrupt tasks in SR623–SR634.
4. If this instruction is not executed, then the contents of SR623–SR634 determine whether an interrupt task is
performed or not.
5. Refer to the examples for the EI instruction (API 0501) for more information.
6-170
6.7 I/O Refreshing Instructions

6.7.1 I/O List of I/O Refreshing Instructions
The following table lists the I/O Refreshing instructions covered in this section.
API Function
0600 REF –  Refreshing the I/O

0601 – DHSRF  Immediate refresh of a high-speed comparative value
0602 REFF –  Refreshing the I/O filtering time
6_
6-171
6.7.2 Explanation of I/O Refreshing Instructions
0600 REF P D, n Refreshing the I/O

D  
n      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D 
n  

AS AS －
Symbol
D ： I/O point state to refresh
n ： Number of I/O points states to refresh
_6 Explanation
1. The I/O states are normally not refreshed until the PLC executes the END instruction. When the PLC starts
scanning the program, it reads and stores the states of the external inputs in memory. After executing the END
instruction, the PLC sends the states of the outputs in the memory to the output terminals. Therefore, when you
need the latest I/O data during the operation process, you can use this instruction, or use the device DX/DY to
refresh the input/output.
2. The operand n must be multiples of eight, such as 8, 16, 24 and up to 256. If the value here is less than a multiple
of eight, it will be seen as the next multiple of eight. For example, the value 20 will be seen as its next multiple of
eight, 24.
3. The number of the high-speed output point is stored in D device for firmware version 1.04.00 and later. If n is 1, it
indicates to refresh the high-speed output value of the corresponding SR immediately. If n is 0, it indicates to stop
high-speed output and refresh the SR current value. For example, during the execution of this instruction, if n is 0
and the external interrupt input is received through X0.0, it indicates an external interrupt occurs in X0.0 and high-
speed outputting through Y0.0 should be stopped immediately. The PLC sets the stop flag SM463 to ON and
refresh the current corresponding output position in SR. Note: if the output completion auto-reset flag is set to ON,
6-172
the PLC sets the output completion auto-rest flag to OFF and refresh the current corresponding output position in
SR. But the PLC does not set the stop flag SM463 to ON.
Value in n D device Action Descriptions

Refresh I/O immediately
n = multiples of eight Y0.0 or X0.0
See Example 1 and 2
Refresh new pulse positon
n = 1*1 High-speed output point
See Example 3
Stop high-speed outputting, set the
High-speed output point stop flag SM463 to ON and refresh
n = 0*1
Without output completion auto-reset flag the current corresponding output
position. See Example 3
Set the output completion auto-reset
High-speed output point flag to OFF and refresh the current
n = 0*1
With output completion auto-reset flag corresponding output position. See
Example 3.
Update the mapped area DS301
n = -1*2 Any input points (X points)
TxPDO (Master <= Slave)
Update the mapped area DS301
n = -1*2 Any output points (Y points)
RxPDO (Master => Slave)
*1: This function is only available for FW V1.04.00 or later.
*2: This function is only available for FW V1.06.40 or later. It is not intended to speed up the PDO data mapping time and
it is suggested to use this function when the PLC scan time is larger than the PDO refreshing time of DS301.
Example 1
1. When X0.0 is ON, the PLC reads the states of the inputs X0.0–X0.15 immediately, and refreshes the input signals
without any delay.
6_
Example 2
When X0.0 is ON, the output signals from Y0.0–Y0.7 are sent to the output terminals. The output signals are refreshed
immediately without waiting for the END instruction to be executed.
6-173
Additional remarks
16#2003.
Example 3
1. During the execution of this instruction, if the external interrupt input is received through X0.0
Value in n D device Action Descriptions
n=1 High-speed output point Y0.0 Refresh new pulse positon Y0.0
immediately (SR460)
n=0 High-speed output point Y0.2 1. Stop high-speed outputting
Without output completion auto-reset flag 2. Set the stop flag SM483 to ON
3. Refresh the current

corresponding output position
SR480
n=0 High-speed output point Y0.4 1. Set the output completion auto-
reset flag SM510 to OFF
With output completion auto-reset flag SM510
2. Refresh the current
_6 corresponding output position.

SR500
X0.0 external interrupt program:
6-174

Immediate refresh of a high-speed
0601 D HSRF P S，S1
comparative value

S 
S1 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S 
S1  

AS － AS
Symbol
S : High-speed counter to be refreshed
S1 : Quantity of I/O to be updated
Explanation
1. The timing for the PLC to update the comparative value in its comparator is when the DHSCS or DHSCR
instruction is scanned by a program successfully. However, the refresh may fail if the scan time is too long or the
6_
input signal comes too fast. In this event, users can use the instruction to assign the new comparative value to the
hardware comparator in the PLC and achieve the real-time comparison.
2. S is the No of the specified high-speed counter to be refreshed. S1 has the same component or variable name as
that in the DHSCS or DHSCR instruction and the immediate value can not be set for S1. If S1 does not have the
same operand as that in the high-speed comparison instruction which has been enabled, the instruction execution
will not take effect.
3. Only the firmware of V1.04.00 and later supports the instruction.
6-175
Example
1. As PLC runs, the comparative value in DHSCS instruction is 5000.
2. When the X0.0 external interrupt occurs, the comparative value in DHSCS is set to 8000 immediately.
Main program:
X0.0 external interrupt program:
Assign the new comparative value to the same variable (E.g. D10 in the example) first and then execute DHSRF
_6 instruction for the update.
6-176
0602 REFF P Xno, Length, Filter Refreshing the I/O filtering time

Xno 
Length      
Filter DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Xno 
Length  
Filter  

AS AS －
Symbol
The starting device number of X to

Xno ：
refresh
n ： Number of I/O points states to refresh
6_
Filter ： Filtering time to refresh (unit: µs)
Explanation
1. This instruction works only with AS series (FWV1.06.00) and ISPSoft V3.06 or later versions.
2. Xno is the starting input number to refresh. Length is the length to refresh. If the X point is the built-in input point of
a CPU, when Xno is X0.3, the value of Length is 3, after executing the REFF instruction, the input filtering time of
X0.3 ~ X0.5 are refreshed.
Since X input point of the extension module is grouping in 8 for a unit, when Xno is X1.9 and the value of Length
is 3, after executing the REFF instruction, the input filtering time of X1.8 ~ X1.15 are refreshed. When Xno is 1.3,
and the value of Length is 3, after executing the REFF instruction, the input filtering time of X1.0 ~ X1.7 are
refreshed. When Xno is X1.3 and the value of Length is 9, the input filtering time of X1.0 ~ X1.15 are refreshed.
3. Xno and Length should be set in the input of PLC input system. If the setting exceeds the range, even if you have
executed REFF instruction, the I/O will NOT be refreshed and error message will NOT be shown.
4. If the X point is the built-in input point of a CPU, the filtering time unit is µs. While if the X point is the input point of
6-177
the extension module, the filtering time unit is ms. This instruction is for refreshing the current filtering time; filtering
time set in HWCONFIG will NOT be affected. But when the value of Filter in the instruction exceeds the setting
range in HWCONFIG, PLC treats the value of Filter as the maximum or the minimum value set in HWCONFIG.
5. When power-on, the filtering time of the CPU and the extension module is refreshed according to the filtering time
set in HWCONFIG.
6. The REFF instruction refreshes the filtering time only at its first execution.
_6
6-178
6.8 Miscellaneous Instructions

6.8.1 List of Miscellaneous Instructions
The following table lists the miscellaneous instructions covered in this section.
API Function
16-Bit 32-Bit instruction
0700 ALT –  Alternating between ON and OFF

0701 TTMR – – Teach mode timer
0702 STMR – – Special timer
0703 RAMP DRAMP – Cyclic ramp signal
0704 MTR – – Matrix input
0705 ABSD DABSD – Absolute drum sequencer
0706 INCD – – Incremental drum sequencer
0708 – DPIDE – PID algorithm
0709 XCMP – – Setting up to compare the inputs of multiple work stations
0710 YOUT – – Comparing the outputs of multiple work stations
0711 – DSUNRS  Sunrise and sunset times
6_
6-179
6.8.2 Explanation of Miscellaneous Instructions
0700 ALT P D Alternating between ON and OFF

D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D 
Pulse instruction 16-Bit instruction 32-Bit instruction

AS AS －
Symbol
Explanation
_6 1. This instruction alternates the state of the device specified by D between ON and OFF.
2. In general, use the ALTP pulse instruction.
Example 1
When X0.0 switches from OFF to ON for the first time, Y0.0 is ON. When X0.0 switches from OFF to ON for the second
time, Y0.0 is OFF.
6-180
Example 2
In the beginning, M0 is OFF; therefore, Y0.0 is ON, and Y0.1 is OFF. When X0.0 switches from OFF to ON for the first
time, M0 is ON; therefore, Y0.0 is OFF, and Y0.1 is ON. When X0.0 switches from OFF to ON for the second time, M0 is
OFF; therefore, Y0.0 is ON, and Y0.1 is OFF.
Example 3
When X0.0 is ON, T0 generates a pulse every two seconds. The output Y0.0 alternates between ON and OFF according
to the pulses generated by T0. 6_
6-181
0701 TTMR D, n Teach mode timer

D   
n       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  
n  

－ AS －
Symbol
D ：Recorded time
n ：Multiplier
Explanation
1. This instruction uses seconds as the unit of time. The time for which a button switch has been turned ON is
multiplied by n, and the product is stored in D. D+1 is for system use only. When the instruction is executed, the
value in D+1 cannot be altered. Otherwise, the time is counted incorrectly.

_6
2. When the conditional contact is ON, D is reset to 0.
3. Setting the multiplier: when n is 0, D uses a second as the timing unit. When n is 1, the time for which the button
switch has been turned ON is multiplied by 10, and D uses 100 milliseconds as the timing unit. When n is 2, the
time for which the button switch has been turned ON is multiplied by 100, and D uses 10 milliseconds as the timing
unit. The greater the value in n, the higher the timing resolution.
n D
K0 (unit: 1 second) 1×T
K1 (unit: 100 milliseconds) 10×T
K2 (unit: 10 milliseconds) 100×T
4. When you use on-line editing, reset the conditional contact to initialize the instruction.
6-182
Example 1
1. The instruction multiplies the time for which the button switch X0.0 has been turned ON by n, and stores the
product in D0. You can use the button switch (ON) to record the time.
2. When X0.0 is switched OFF, the value in D0 is unchanged.
X0.0
D0
D0
T T
The time for whic h The time for whic h
the button switc h is the button switc h is
turned on. turned on.
(Unit: Second) (Unit: Second)
6_
Additional remarks
16#2003.
16#200B.
3. If you declare the operand D in ISPSoft, the data type is ARRAY [2] of WORD/INT.
6-183
0702 STMR S, m, D Special timer

S 
m       
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
m  
D 

－ AS －
Symbol
S ： Timer number (T0-T511)
m ： Setting value of the timer
D ： Output device
Explanation
_6 1. This instruction generates timing for the off-delay relay, the one-shot circuit, and the flashing circuit.
2. This instruction uses 100 milliseconds as the timing unit. If the setting value for m is 50, the time value is 5
seconds.
3. You cannot use this timer repeatedly.
4. D occupies four consecutive devices.
5. Before the instruction is executed, reset D-D+3.
6. When the conditional contact is not enabled and the value of the device meets one of the two conditions mentioned
below, D, D+1, and D+3 are ON for m seconds before they are switched OFF. When the conditional contact is not
enabled and the value of the device does not meet either of the two conditions mentioned below, D-D+3 keep OFF.
 The value of the timer is less than or equal to m, D is ON, and D+1 is OFF.
 The value of the timer is less than m, D +2 is OFF, and D, D+1, and D+3 are ON.
7. When the on-line editing is used, Reset the conditional contact to initialize the instruction.
8. The value in m must be between 1–32767.
6-184
Example
1. When X0.0 is ON, the instruction specifies the timer T0, and the setting value of T0 is five seconds.
2. Y0.0 is the off-delay contact. When X0.0 switches to ON, Y0.0 is ON. Five seconds after X0.0 switches to OFF,
Y0.0 is OFF.
3. When X0.0 switches to OFF, Y0.0 is ON for five seconds.
4. When X0.0 switches ON, Y0.2 is ON for five seconds.
5. Five seconds after X0.0 switches to ON, Y0.3 is ON. Five seconds after X0.0 switches to OFF, Y0.3 is OFF.
X0.0
Y0.0
5 s econds 5 s econds
Y0.1
5 s econds 5 s econds
Y0.2
6_
5 s econds
Y0.3
5 s econds 5 s econds 5 s econds
6. When the conditional contact X0.0 is followed by the b contact Y0.3, the flasher circuit passes through Y0.1 and
Y0.2. When X0.0 is switched OFF, Y0.0, Y0.1, and Y0.3 are switched OFF, and T0 is reset to 0.
X 0.0
Y 0.1
5 s econds
Y 0.2
5 s econds
6-185
Additional remarks
16#2003.
2. If the value in m is less than 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
_6
6-186
0703 D RAMP S1, S2, D, n Cyclic ramp signal

S1         
S2         
D   
n         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
D    
n    

－ AS AS
Symbol
S1 ： Initial value of the ramp signal
S2 ： Final value of the ramp signal
D ： Duration of the ramp signal 6_

n ： Number of scan cycles
Explanation
1. This instruction gets the linear slope, which has an absolute relationship with the scan time. Therefore it is
suggested that you set a fixed scan time or write this instruction in a timer interrupt task.
2. You write the initial value and final value of the ramp signal into S1 and S2 respectively in advance. When X0.0 is
ON, D increases from the setting value in S1 to the setting value in S2. The number of scan cycles is stored in D+1.
When the value in D is equal to that in S2, or when the value in D+1 is equal to n (to the number of scan cycles),
then SM687 is ON.
3. When the conditional contact is not enabled, the value in D, and D+1 are both 0, and SM687 is OFF.
4. When using on-line editing, Reset the conditional contact to initialize the instruction.
5. Refer to the ISPSoft User Manual for more information on setting a fixed scan time.
6. The value of n must be between 1–32767. When n is out of range, this instruction is not executed.
6-187
8. Use the SM686 flag to reset the value in D to 0. Refer to the examples below for details.
Example
When you use the instruction with an analog signal output, it acts to cushion the starting and stopping of the machinery.
1. During execution, when X0.0 switches to OFF, the execution of the instruction stops. When X0.0 switches to ON
again, SM687 is OFF, D12 is reset to the setting value in D10, D13 is reset to 0, and the ramp calculation is
restarted.
2. During execution, SM686 is OFF, and when D12 reaches the setting value in D11, SM687 switches to ON as a
scan cycle. When D12 resets to the setting value in D10, D13 resets to 0.
D11
_6 D10
D12
D12
D11
D10
The number of scan cycl e i s n. The number of scan cycl e i s n.

D10<D11 D10>D11
The number of scan cycl e i s stored i n D13.
3. When SM686 is ON, and D12 reaches the setting value in D11, the value in D12 is not reset to 0, and SM687 is
ON. As long as the conditional contact is closed (ON), the value in D12 resets to 0 and SM687 is OFF. When
SM686 is ON or OFF, the value in D12 changes as shown below.
6-188
SM686=O N SM686=O FF
X0.0 X0.0
T he signal is enabled. T he signal is enabled.
D11
D11
D12 D12
D10 D10
SM687 SM687
Additional remarks
16#2003.
2. If n is less than 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
3. For the 16-bit instruction, if you declare the operand D in ISPSoft, the data type is ARRAY [2] of WORD/INT.
4. For the 32-Bit instruction, if you declare the operand D in ISPSoft, the data type is ARRAY [2] of DWORD/DINT.
6_
6-189
0704 MTR S, D1, D2, n Matrix input

S 
D1 
D2    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S 
D1 
D2 
n  

－ AS －
Symbol
S ： First input device in the matrix scan
First output device in the matrix

D1 ：
scan
First corresponding device in the
D2 ：
_6
matrix scan
n ： Number of rows to scan
Explanation
1. This instruction scans and stores the states of eight sequential input devices. S specifies the first input device in
the matrix scan.
2. D1 specifies the transistor output device Y as the first device in the matrix scan. When the conditional contact is
OFF, the states of the n devices starting from D1 are OFF.
3. One row of inputs is refreshed every scan cycle. There are 16 inputs in a row, and the scan starts from the first row
and goes to the nth row.
4. The eight input devices starting from the device specified by S are connected to the n output devices starting from
the device specified by D1 to form the n rows of switches. The matrix scan reads the states of the n rows of
switches, and stores the states in the devices starting from the device specified by D2.
5. You can connect up to 8 rows of input switches in parallel to get 64 inputs (8×8=64).
6. The interval between executions of this instruction should be longer than the time it takes for the states of the I/O
points on the module to be refreshed. Otherwise, the instruction cannot read the correct states of the inputs. See
6-190
Additional remarks, below.
7. In general, the conditional contact used in the instruction is SM400: the flag is always ON when CPU runs.
Example 1
1. When M0 is ON, the MTR instruction is executed. The instruction reads the states of the two rows of switches in
order, and stores them in the internal relays M10–M17 and M20–M27 respectively.
2. The diagram below is the external wiring diagram of the 2-by-8 matrix input circuit for X0.0–X0.7 and Y0.0–Y0.1.
The corresponding internal relays of the 16 switches are M10–M17 and M20–M27.
M20 M21 M22 M23 M24 M25 M26 M27 6_

Y0.1
Y0.0
X0.1 X0.2 X0.3 X0.4 X0.5 X0.6 X0.7
M10 M11 M12 M13 M14 M15 M16 M17
X0.0 X0.1 X0.2 X0.3 X0.4 X0.5 X0.6 X0.7
3. The instruction connects eight input devices starting from X0.0 to the two output devices starting from Y0.0 to form
the two rows of switches. The matrix scan reads the states of the two rows of switches, and stores the states in the
devices starting from M10 (specified by D2). That is, it stores the states of the first row of switches in M10–M17,
and stores the states of the second row of switches in M20–M27.
6-191
T he first row of i nput s ignals ar e r ead.
Y0.0 1 3
T he second r ow of input s ignal s ar e read.
Y0.1 2 4
Additional remarks
1. When this instruction is executed, a cycle time that is too long or a too short causes the state of the switches to be
read incorrectly. Use the following tips to solve this issue.
 When the scan cycle is too short, the I/O may not be able to respond in time and the correct states of the
inputs cannot be read. You can set a fixed scan time to solve this issue.
 When the scan cycle is too long, the switch may be slow to react. You can write this instruction in a timer
interrupt task to set a fixed time to execute this instruction.
2. If S+7, D1+n-1, or D2+(n*8)-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error
4. If you declare the operand S in ISPSoft, the data type is ARRAY [8] of BOOL.
_6
6-192
0705 D ABSD S1, S2, D, n Absolute drum sequencer

S1       
S2       
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
D 
n    

－ AS AS
Symbol
Initial device for the

S1 ：
comparison
S2 ： Comparison value
： Comparison result
6_
D
n ： Number of comparison groups
Explanation
1. Use this instruction to generate multiple pulses corresponding to the current values of the counter.
2. Only the DABSD instruction can use the 32-Bit counter, but not the device E.
3. When using the ABSD instruction, n must be between 1–256.
Example 1
1. Before the ABSD instruction is executed, the MOV instruction writes the setting values in D100–D107. The values
in the even devices are minimum values, and the values in the odd devices are maximum values.
2. When X0.0 is ON, the instruction compares the current value of the counter C10 with the maximum values and the
minimum values in D100–D107, and stores the comparison results in M10–M13.
3. When X0.0 is OFF, the original states of M10–M13 are unchanged.
6-193
4. When the current value of C10 is between the minimum value and the maximum value, M10–M13 are ON.
Otherwise, M10–M13 are OFF.
Minimum value Maximum value Current value of C10 Output
D100=40 D101=100 40≦C10≦100 M10=ON
D102=120 D103=210 120≦C10≦210 M11=ON
_6 D104=140 D105=170 140≦C10≦170 M12=ON
D106=150 D107=390 150≦C10≦390 M13=ON
5. Suppose the minimum value is larger than the maximum value. When the current value of C10 is less than the
maximum value (C10＜60), or when the current value of C10 is larger than the minimum value (C10＞140), M12 is
ON. Otherwise, M12 is OFF.
Minimum value Maximum value Current value of C10 Output
D100=40 D101=100 40≦C10≦100 M10=ON
D102=120 D103=210 120≦C10≦210 M11=ON
D104=140 D105=60 60≦C10≦140 M12=OFF
D106=150 D107=390 150≦C10≦390 M13=ON
6-194
40 100
M10
120 210
M11
60 140
M12
150 390
M13
0 200 400
Additional remarks
1. For the 16-bit instruction, if S+2*n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
error code in SR0 is 16#2003.
2. For the 32-bit instruction, if S+4*n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
3. For the 16-bit instruction, if D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
4. For the 32-bit instruction, if D+2*n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
5. For both the 16-bit instruction and the 32-bit instruction, if n is not between 1–256, the instruction is not executed, 6_
SM0 is ON, and the error code in SR0 is 16#200B.
6-195
0706 INCD S1, S2, n, D Incremental drum sequencer

S1      
S2      
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D 
n  

－ AS －
Symbol
S1 ： Initial device for comparison
S2 ： Counter number
_6 n ： Number of comparison groups
Explanation
1. This instruction generates multiple pulses for a pair of counters.
2. The instruction compares the current value of S2 with the setting value in S1. When the current value matches the
setting value, the instruction resets the current value of S2 to 0, and the stores the current comparison group
number in S2+1.
3. After the comparison between the current values of S2 and the n groups of values is complete, SM688 is ON for a
scan cycle.
4. When the conditional contact is not enabled, the value in S2 is 0, the value in S2+1 is 0, D-D+n-1 are OFF, and
SM688 is OFF.
5. When using on-line editing, Reset the conditional contact to initialize the instruction.
6-196
Example
1. Before the INCD instruction is executed, the MOV instruction writes the setting values in D100–D104. The values
in D100–D104 are 15, 30, 10, 40, and 25 respectively.
2. The instruction compares the current values in C10 with the setting values in D100–D104. When the current value
matches the setting value, the instruction resets C10 to 0, and counts again.
3. The instruction stores the current comparison group number in C11.
4. When the value in C11 changes by one, M10–M14 act correspondingly. Referto the following timing diagram.
5. When the comparison between the current values in C10 and the values in D100–D104 is complete, SM688 is ON
for a scan cycle.
6. When X0.0 is switched from ON to OFF, C10 and C11 are reset to 0, and M10–M14 are switched OFF. When X0.0
switches to ON again, the instruction execution starts from the beginning.
6_
6-197
X0.0
40
30 30
25
C10 15 15 15
10
Current v alue
4
C11 3
2
Current v alue 0 1 1 1
0 0
M10
M11
M12
M13
M14
SM688
Additional remarks
1. If S2+1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
_6 2. If S1+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
16#2003.
5. If you declare the operand S2 in ISPSoft, the data type is ARRAY [2] of WORD/INT.
6-198
0708 D PIDE As shown in the following table PID algorithm

PID_RUN     
SV  
PV  
PID_MODE   
PID_MAN     
MOUT_AUTO     
CYCLE   
KC_Kp 
Ti_Ki 
Td_Kd 
Tf  
PID_EQ     
PID_DE     
PID_DIR     
ERR_DBW   
MV_MAX   
MV_MIN   
MOUT 
BIAS   
I_MV 
MV  6_
DWORD
STRING
LWORD
LREAL
WORD
BOOL
Data
REAL
UINT
DINT
LINT
TMR
CNT
INT
type

－－ AS
6-199
Symbol
EN ： Enable/Disable the instruction
PID_RUN ： Enable the PID algorithm
SV ： Target value (SV)
PV ： Process value (PV)
PID_MODE ： PID control mode
PID_MAN ： PID Auto/Manual mode
MOUT_AUTO ： Manual/Auto output value
CYCLE ： Sampling time (CYCLE)
Kc_Kp ： Proportional gain
Ti_Ki ： Integral coefficient (sec. or 1/sec)
Td_Kd ： Derivative coefficient (sec)
Tf ： Derivate-action time constant (sec)
PID_EQ ： PID formula types
PID_DE ： Calculation of the PID derivative error
PID_DIR ： PID forward/reverse direction (PID_DIR)
Range within which the error value is

ERR_DBW ：
_6 counted as 0
MV_MAX ： Maximum output value (MV_MAX)
MV_MIN ： Minimum output value (MV_MIN)
MOUT ： Manual output value (MOUT)
BIAS ： Feed forward output value
I_MV ： Accumulated integral value
MV ： Output value (MV)
Explanation
1. This instruction implements the PID algorithm. After the sampling time is reached, the instruction applies PID
algorithm. PID stands for Proportional, Integral, Derivative. The PID control is widely applied to mechanical,
pneumatic, and electronic equipment.
2. The parameter settings are listed in the following table.
6-200
Operand Data type Function Setting range Description
True: use the PID algorithm.
PID_RUN BOOL Enabling the PID algorithm False: reset the output value (MV) to 0,
and stop using the PID algorithm.
Range of
single-
precision
SV REAL SV Target value
floating-
point
numbers
Range of
single-
precision
PV REAL PV Process value
floating-
point
numbers
0: Automatic control
When PID_MAN switches from True
to False, invoke the output value 6_

(MV) in the automatic algorithm. If
the MV exceeds the limits of
MV_MAX or MV_MIN, I_MV value
stays the same and without
updating.
1: Auto tuning the parameters for the

PID_MODE DWORD/DINT PID control mode temperature control. After tuning is
done, the system is in auto control
mode (PID_MODE is set to 0) and fill
in the appropriate parameters
(Kc_Kp, Ti_Ki, Td_Kd, and Tf)
2: Automatic control (including
I_MV): When PID_MAN switches
from TRUE to FALSE, the MV value
is invoke the output value (MV) in the
6-201
automatic algorithm. If the MV
exceeds the limits of MV_MAX or
MV_MIN, I_MV use the formula to
calculate the correct value and
adjust its value accordingly. This can
reduce the response time of the
reverse action.
Note: when the mode is set to 1, auto
tuning the parameter, you cannot
use numerical value to set up.
True: Manual
Output the MV according to
MOUT, but it is still between
MV_MIN and the MV_MAX. This
setting has no effect when
PID_MAN BOOL PID A/M mode PID_MODE is set to 1.
False: Automatic
Output the MV according to the
PID algorithm, and the output

_6
value is between MV_MIN and
MV_MAX.
True: Automatic
MOUT varies with the MV.
MOUT_AUTO BOOL MOUT automatic change mode False: Normal
MOUT does not vary with the
MV.
When the instruction
is scanned, use the
PID algorithm
according to the
1–40,000
CYCLE DWORD/DINT Sampling time (TS) sampling time, and
(unit: ms)
refresh MV. The PLC
requires that the
instruction execute; it
will not run the
6-202
sampling time
automatically. If TS is
less than 1, it is
counted as 1. If TS is
larger than 40,000, it
is counted as 40,000.
When using the PID
instruction in an
interval interrupt task,
the sampling time is
the same as the
interval between the
timed interrupt tasks.
The sampling cycle
setting of the sampling
cycle is ignored here.
Calculated
Range of
proportional
positive
coefficient (Kc or Kp)
Calculated proportional single-
If the P coefficient is
6_
Kc_Kp REAL coefficient (Kc or Kp, according precision
less than 0, the Kc_Kp
to the settings in PID_EQ) floating-
is 0. Independently, if
point
Kc_Kp is 0, it is not
numbers
controlled by P.
Range of If the calculated
positive coefficient I is less
single- than 0, Ti_Ki is 0. If
precision Ti_Ki is 0, it is not

Integral coefficient (Ti or Ki,
floating- controlled by I.
Ti_Ki REAL according to the settings in
point
PID_EQ)
numbers
(unit: Ti =
sec; Ki =
1/sec)
6-203
positive coefficient D is less
single- than 0, Td_Kd is 0. If

Derivative coefficient (Td or Kd,
precision Ti_Ki is 0, it is not
Td_Kd REAL according to the settings in
floating- controlled by D.
PID_EQ)
point
numbers
(unit: sec)
Range of If the derivate-action
positive time constant is less
single- than 0, Tf is 0 and it is
precision not controlled by the

Tf REAL Derivate-action time constant
floating- derivate-action time
point constant (derivative
numbers smoothing).
(unit: sec)
TRUE: dependent formula

PID_EQ BOOL PID formula types
FALSE: independent formula
_6 TRUE: use the variations in the PV to
calculate the control value of the
derivative (Derivative of the PV).

The calculation of the PID
PID_DE BOOL FALSE: use the variations in the error
derivative error
(E) to calculate the control value
of the derivative (derivative of
the error).
True: forward action (E=SV-PV)

PID_DIR BOOL PID forward/reverse direction
False: reverse action (E=PV-SV)
The error value (E) is

Range of
the difference
single-
between the SV and
Range within which the error precision
ERR_DBW REAL the PV. When the
value is counted as 0. floating-
setting value is 0, the
point
function disabled;
numbers
otherwise the CPU
6-204
module checks
whether the present
error is less than the
absolute value of
ERR_DBW, and
checks whether the
present error meets
the cross status
condition. If the
present error is less
than the absolute
value of ERR_DBW,
and meets the cross
status condition, the
present error is
counted as 0, and the
PLC applies the PID
algorithm ; otherwise
the present error is
brought into the PID 6_

algorithm according to
the normal
processing.
Suppose MV_MAX is
set to 1,000. When
MV is larger than
Range of
1,000, 1,000 is the
single-
output. The value in
precision
MV_MAX REAL Maximum output value MV_MAX should be
floating-
larger than that in
point
MV_MIN. Otherwise,
numbers
the maximum MV and
the minimum MV are
reversed.
MV_MIN REAL Minimum output value Range of Suppose MV_MIN is
6-205
single- set to -1,000. When
precision the MV is less than -
floating- 1,000, -1,000 is the
point output.
numbers
Range of When set to PID

single- Manual, the MV value
precision is output as the setting

MOUT REAL MV
floating- value for MOUNT,
point between MV_MAX
numbers and MV_MIN.
Range of
single-
Feed forward output
precision
BIAS REAL Feed forward output value value, used for the
floating-
PID feed forward.
point
numbers
Accumulated integral
_6 value temporarily
stored, and usually for
reference. You can
still clear or modify it
according to your
Range of needs.
I_MV
single- PID mode in 0
(occupies 15 Accumulated
precision (Automatic control):
consecutive REAL I_MV integral
floating- When the MV is
DWord value
point greater than the
devices）
numbers MV_MAX, or when the
MV is less than
MV_MIN, the
accumulated integral
value in I_MV is
unchanged.
PID mode in 2
6-206
(Automatic control,
including I_MV):
When PID_MAN
switches from TRUE
to FALSE, the MV
value is invoke the
output value (MV) in
the automatic
algorithm. If the MV
exceeds the limits of
MV_MAX or MV_MIN,
I_MV use the formula
to calculate the
correct accumulated
integral value and
adjust its value
accordingly. This can
reduce the response
time of the reverse
action. 6_
I_MV+1 The previous error value is temporarily stored here.
I_MV+2–
For system use only
I_MV+5
I_MV+6 The previous PV is temporarily stored here.
I_MV+7–
For system use only
I_MV+14
MV REAL MV The MV is between the MV_MIN and the MV_MAX.
6-207
The diagram of switching to PID_MAN / MOUT_AUTO:

PID_MAN
PID
Calculation FALSE
MV
Manual input TRUE

MOUT
TRUE
FALSE
MOUT_AUTO
1. When switching the control mode (PID_MAN=0) from automatic to manual, you can set the flag MOUT_AUTO
to 1 and the output value of MOUT goes along with the output value of MV. After switching to the manual mode
(PID_MAN=1), you can set the MOUT_AUTO to 0.
2. When PID_RUN changes from TRUE to FALSE, the PLC resets the value in MV to 0. When the value in MV is
to be retained, you can set EN to FALSE to dismiss the instruction and to keep the output value in MV.
Example 1
1. Set all parameters before executing this instruction.
2. When M0 is ON, the instruction is executed. When PID_RUN is ON, the instruction applies the DPID algorithm.
When PIC_RUN is OFF, MV is 0, and store the value in MV. When M0 switches to OFF, the instruction is not
executed, and the previous data is unchanged.
_6
Additional remarks
1. The instruction can be used several times, but the registers specified by I_MV–I_MV+14 cannot be the same.
2. I_MV occupies 30 registers.
3. You can only use the 32-bit instruction in cyclic tasks and interval interrupt tasks. When using the 32-bit instruction
in an interval interrupt task, the sampling time (Cycle) is the same as the interval between the timed interrupt tasks.
4. When the instruction is scanned, the 32-bit PID algorithm is applied according to the sampling time (Cycle), and it
refreshes MV. When you use the instruction in an interrupt task, the sampling time (Cycle) is the same as the
6-208
interval between the timed interrupt tasks. The PID algorithm is applied according to the interval between the timed
interrupt tasks.
5. Before the 32-bit PID algorithm is applied, the process value used in the PID instruction has to be a stable value.
When you need the input value in the module to implement the DPID algorithm, must note the time it takes for the
analog input to be converted into the digital input.
6. When the PV (process value) is in the range of ERR_DBW, at the beginning, the present error is brought into the
PID algorithm according to the normal processing, and then the CPU module checks whether the present error
meets the cross status condition: PV (process value) goes beyond the SV (target value). Once the condition is met,
the present error is counted as 0 when applying the PID algorithm. After the PV (process value) is out of the
ERR_DBW range, the present error is brought into the PID algorithm again. If PID_DE is true, that means it uses
the variations in the PV to calculate the control value of the derivative, and after the cross status condition is met,
the PLC treats Δ PV as 0 to apply the PID algorithm. (Δ PV= current PV – previous PV). In the following example,
the present error is brought into the PID algorithm according to the normal processing in section A ,and the present
error or Δ PV is counted as 0 to apply the PID algorithm in the section B.
6_
The PID algorithm:

1. When you set PID_MODE to 0, the PID control mode is the automatic control mode.
 Independent Formula & Derivative of E（PID_EQ=False & PID_DE=False）

t
dE
MV = K P E + Ki ∫ Edt + K d * + BIAS E = SV – PV or E = PV – SV
0
dt
 Independent Formula & Derivative of PV（PID_EQ=False & PID_DE=True）
t
dPV
MV = K P E + Ki ∫ Edt − K d * + BIAS E = SV – PV
0
dt
Or
t
dPV
MV = K P E + Ki ∫ Edt + K d * + BIAS E =PV – SV
0
dt
 Dependent Formula & Derivative of E（PID_EQ=True & PID_DE=False）
 1
t
dE 
MV = K c  E + ∫ Edt + Td *  + BIAS E = SV – PV or E = PV – SV
 Ti 0 dt 
 Dependent Formula & Derivative of PV（PID_EQ=True & PID_DE=True）
6-209
 1
t
dE 
MV = K c  E + ∫ Edt − Td *  + BIAS E = SV – PV
 Ti 0 dt 
Or
 1
t
dE 
MV = K c  E + ∫ Edt + Td *  + BIAS E = PV – SV
 Ti 0 dt 
2. When you set PID_MODE to 1, the PID control mode is the automatic tuning mode. After the tuning of the
parameter is complete, PID_MODE is set to 0. The PID control mode then becomes the automatic control mode.
PID Block Diagram:

PID Block Diagram (Independent)
PID_D IR
E
+ 1
SV + DEAD BAND
-
REVERSE
PV 0
X(-1)
ERR_DBW
Kc_Kp
PID-P
>0 PID_MAN
BIAS
+ 0
<=0 +
0 +
Kc_Kp MV_LIMIT
1
MV
Ti_Ki
PID-I
>0
MV_MAX, MV_MIN
+
<=0 +
0 +
Ti_Ki
_6
MOUT_AUTO
+ MOUT
0
Td_Kd MOUT
PID-D PID_MAN
>0 1
0
<=0
0 1
Td_Kd, Tf MOUT
6-210
PID Block Diagram (Dependent)

PID_D IR
E
+ 1
SV + DEAD BAND PID-P
-
REVERSE
PV 0
X(-1)
Kc_Kp
ERR_DBW Kc_Kp
>0
<=0
0
PID_MAN
BIAS
+ 0
+
+
MV_LIMIT
1
Ti_Ki MV
PID-I
>0
MV_MAX, M V_MIN
<=0
0
Ti_Ki MOUT_AUTO
MOUT
0
Td_Kd MOUT PID_MAN
PID-D
>0 1
0
<=0
0 1
Td_Kd, Tf MOUT
Suggestions
1. Since you can use the 32-bit instruction in a lot of controlled environments, you must choose the appropriate control
function. For example, to prevent improper control, do not use PID_MODE in the motor controlled environment when
it is set to 1.
2. When you tune the parameters Kc_Kp, Ti_Ki, and Td_Kd (PID_MODE is set to 0), you must tune KP first (based on 6_
experience), and then set Ti_Ki and Td_Kd to 0. When you can handle the control, you can increase Ti_Ki and
Td_Kd. When Kc_Kp is 1, it means that the proportional gain is 100%. That is, the error value is increased by a
factor of one. When the proportional gain is less than 100%, the error value is decreased. When the proportional
gain is larger than 100%, the error value is increased.
3. To prevent the parameters that have been tuned automatically from disappearing after a loss of power, you must
store the parameters in the latched data registers when PID_MODE is set to 1. The parameters that have been
automatically tuned are not necessarily suitable for every controlled environment. Therefore, you can modify the
automatically tuned parameters; however, it is suggested that you only modify the Ti_Ki and the Td_Kd.
4. You can use this instruction with many parameters, but to prevent improper control, do not set the parameters
randomly.
6 - 2 11
Example 2: Tuning the parameters used with the PID instruction

b
Suppose that the transfer function of the plant is the first-order function G(s) = , the SV is 1, the sampling time Ts is
s+a
10 milliseconds. It is suggested that you follow these steps when tuning the parameters.
Step 1: First, set the KI and the KD to 0. Next, set the KP to 5, 10, 20 and 40 successively, and record the target values
and the process values. The results are shown in the following diagram.
1.5
K P =40 SV= 1
K P =20 K P =10
1
K P =5
0.5
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 T ime (s ec)
Step 2: When the KP is 40, there is overreaction. When the KP is 20, the reaction curve of PV is close to SV, and there is
no overreaction. However, due to the fast start-up, the transient output value (MV) is big. Neither 40 nor 20 is a
suitable value. When the KP is 10, the reaction curve of PV approaches SV smoothly. When KP is 5, the reaction
is too slow. Therefore, KP = 10 is the best choice.
Step 3: After setting KP to 10, increase KI. For example, KI is successively set to 1, 2, 4, and 8. KI should not be larger
than KP. Then, increase KD. For example, successively set KD to 0.01, 0.05, 0.1, and 0.2. KD should not be larger
than ten percent of KP. Finally, the relation between PV and SV is shown in the following diagram.
1 .5
_6
PV= SV
0 .5
K P =10,KI = 8,K D=0.2
0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 T ime (s ec)
Note: This example is only for reference. You must tune the parameters properly according to the actual condition of the
control system.
6-212
Example 3: Using the automatic tuning function to control the temperature

Because you may not be familiar with the characteristics of the temperature environment to be controlled, you can use
the automatic tuning function to make an initial adjustment (PID_MODE is set to 1). After the automatic tuning of the
parameter is complete, PID_MODE is set to 0. The controlled environment in this sample is an oven. The following
example program shows the setting values for the instruction.
The experimental result of the automatic tuning function is shown in the following graph. 6_
6-213
The following graph shows the result of using the automatically tuned parameters to control the temperature.
This graph shows that using automatically tuned parameters can result in a good temperature control result. It only takes
about twenty minutes to control the temperature. The following graph shows the result of changing the target
temperature from 80°C to 100°C.
_6
This graph shows that when the target temperature changes from 80°C to 100°C, the automatically tuned parameters still
work to control the temperature in a reasonable amount of time.
6-214
Example 4: Creating a DPIDE instruction in a function block and setting to the cyclic task mode to read the function
block written with a DPIDE instruction to control the temperature.
1. Set the value in DPIDE_CYCLE to 1000 ms, and execute the DPIDE instruction by reading the function block written
with a DPIDE instruction. Whenever the function block is scanned, the PID algorithm is applied according to the sampling
time (Cycle), and it refreshes the output value (DPIDE_MV).
2. Set the DPIDE_MODE =1 for auto tuning the parameters for the temperature control. After tuning is done, the
system is in auto control mode (PID_MODE is set to 0) and fill in the appropriate parameters (Kc_Kp, Ti_Ki, Td_Kd, and
Tf).
3. Main program (cyclic task): Since PLC only executes the DPIDE instruction when it is scanned. If we use TMRH to
work with the DPIDE instruction, for example, set the TMRH to 1000 ms, the system calls the function block written with
a DPIDE instruction (AS_DPIDE) every 1000 ms. See the example program below.
6_
4. Function block (AS_DPIDE): Execute the DPIDE instruction by reading the function block written with a DPIDE
instruction. Whenever the function block is scanned, the PID algorithm is applied according to the sampling time (Cycle),
and it refreshes the output value (DPIDE_MV). (Refer to ISPSoft Manual for more details on how to create a function
block.)
6-215
NOTE: The parameters PID_MODE, Kc_Kp, Ti_Ki, Td_Kd, and Tf in the function block written with a DPIDE instruction
should be declared as VAR_IN_OUT.
_6
Example 5: Creating a DPIDE instruction in a time interrupt program to control the temperature. (Note: use the time
interrupt as the cycle time of DPIDE.)
1. Set the time interrupt to 1000 ms in HWCONFIG.

2. Create a DPIDE instruction in a time interrupt program. Whenever a time interrupt occurs, the PID
algorithm is applied. The setting in DPIDE_CYCLE is invalid here.
3. Set the DPIDE_MODE =1 for auto tuning the parameters for the temperature control. After tuning is done,
the system is in auto control mode (PID_MODE is set to 0) and fill in the appropriate parameters (Kc_Kp, Ti_Ki,
Td_Kd, and Tf).
Main program (cyclic task)
6-216
Time interrupt program I601 and the setting parameters
6_
6-217

Setting up to compare the inputs of
0709 XCMP S1, S2, S3, S4, D,
multiple work stations

S1 
S2 
S3 
S4 
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data INT
type
S1 
S2 
S3  
S4  
D  

－ AS －
Symbol
S1 ： Trigger input point
S2 ： High-speed counter number

_6 Setting for the numbers for work
S3 ：
station and objects
Reference value for comparison and
S4 ：
the observational error
First corresponding device for the
D ：
comparison result in the stack area
Explanation
1. This instruction is only available for AS Series PLCs with firmware version 1.04.00 or higher. The instruction cannot
be used in the ST programming language, interrupt tasks or function block which is called only once.
2. Use this instruction along with API 0710 YOUT. It is very useful for the applications of assembly and processing
with multiple work stations, including painting, carpentry, metalwork sectors and many more.
3. Use S1 for setting the trigger input points; the high-speed inputs are X0.0–X0.15 and the other inputs are general
type. Executing the instruction enables the external interrupts for the inputs (X0.0–X0.15). Therefore do NOT use
the inputs with interrupt tasks; otherwise, when the instruction is executed, the interrupts are disabled and resumed
only after the instruction completes. The general type inputs are affected by the scan time though they are suitable
for the environments where the inputs are not as stable.
6-218
4. S2 works with 32-bit counters (HC0–HC255). When the inputs are the high-speed trigger input type, implement the
hardware high-speed counter and use the DCNT instruction to enable the counter. When you need high-speed output,
use the DMOV instruction to copy the output current position; for example copying the axis of SR460 to HC0, (DMOV
SR460 HC0).
5. For PLC with FW V1.04.00 (V1.04.00 included) or previous versions:

S3 occupies three consecutive 16-bit devices. S3+0 is n (the work station number) and S3+1 is m (the maximum
object number). S3+2 is the result of the object being filtered. The range for n and m is between 1–32. When this
value is out of range, the value used is the maximum (32) or the minimum (1). The range for S3+2 (the number of
filter) is between 0–32767. Zero is used for any value less than 0, and a value of 0 disables the filtering function. Be
sure to declare an array of 3 words or 3 consecutive word type variables.
6. For PLC with FW V1.06.00 (V1.06.00 included) or higher versions:

S3 occupies seven consecutive 16-bit devices. S3+0 is n (the work station number) and S3+1 is m (the maximum
object number). S3+2 is the result of the object being filtered. The range for n and m is between 1–64. When this
value is out of range, the value used is treated as the maximum (32) or the minimum (1). The range for S3+2 (the
number of filter) is between 0–32767. Zero is used for any value less than 0 ; and a value of 0 disables the filtering
function. S3+3 (Low Word) and S3+4 (High Word) are for rising-edge values. S3+5 (Low Word) and S3+6 (High Word)
are for falling-edge values (32-bit). Be sure to declare an array of 7 words or 7 consecutive word type variables.
7. Set the maximum number for S3+1 (m). If m < n, note the objects and make sure they are sufficient on the production
line.
8. S4 occupies 3xn consecutive 32-bit devices (6xn 16-bit devices). If the required space exceeds the range of device
D, the instruction is not executed. The value of n is the work station number set in the operand S3. The following table
lists the functions for each device and the corresponding number for S4. Be sure to declare an array of 3n double
words or 3 consecutive double word type variables for S.
Function Work station 1 Work station 2 ‧‧‧ Work station n 6_

Reference value for comparison (32-bit) S4+0 S4+2 ‧‧‧ S4+(n-1)x2
Observational error of the compared S4+2xn S4+2xn+2 ‧‧‧ S4+(2xn-1)x2

stack area for the entering-work-station
ones (32-bit)
Observational error of the compared S4+4xn S4+4xn+2 ‧‧‧ S4+(4xn-1)x2
stack area for the leaving-work-station
ones (32-bit)
When you set the reference value to 0 for a specific work station, the specific work station stops working. You can
use this technique to manage work stations.
9. D is the first corresponding device for the comparison result in the stack area. D occupies 2xn consecutive 16-bit
devices and 2xmxn consecutive 32-bit devices (or 4xmxn consecutive 16-bit devices). If the required space exceeds
the range of device D, the instruction is not executed. The following table lists the functions for each device and the
corresponding number for D.
6-219
Function Work station 1 Work station 2 ‧‧‧ Work station n
Value of the head index (16-bit) D+0 D+1 ‧‧‧ D+(n-1)
Value of the tail index (16-bit) D+n D+(n+1) ‧‧‧ D+(2xn-1)
Compared stack area 1 for the D+2xn D+2xn+2 ‧‧‧ D+2xn+2(n-1)
entering -work-station ones (32-bit)
Compared stack area 1 for the D+4xn D+4xn+2 ‧‧‧ D+4xn+2(n-1)
leaving-work-station ones (32-bit)
：：：：：
Compared stack area m for the D+4xmxn-2xn ‧‧‧ D+4xmxn-2
entering -work-station ones (32-bit)
Compared stack area m for the D+4xmxn ‧‧‧ D+4xmxn+2 (n-1)
leaving-work-station ones (32-bit)
D tends to occupy more space in the stack area. If the required space exceeds the range of device D, the PLC only
executes what is valid in the storage and does not show a no warning. It is suggested that you declare an array of
2xn+4xmxn words for D.
10. There is no limit on the number of times you can execute the instruction but only one execution can be done at a
time.
11. It is suggested to use this instruction with the YOUT instruction (API 0710), and use the same first corresponding
_6 device for the comparison result in the stack area (D).
The following timing diagram shows executing the high-speed counter and filter (reading from right to left).
3 1 1 2
5 1 4 5 4 1 1
① PLC reads the current counter value and stores the value in a register.
② Drop the shifting counter value: when the signal is unstable (the number of filters is not sufficient).
③ Drop the shifting counter value: when the signal is unstable (the number of filters is not sufficient).
④ Record the counter value to the compared stack area for the entering-work-station ones, when the signal is
stable.
6-220
⑤ Record the counter value to the compared stack area for the leaving-work-station ones, when the signal is
stable.
13. For PLC with FW V1.06.00 (V1.06.00 included) or higher versions:
The following timing diagram shows executing the high-speed counter and filter (reading from right to left).
① PLC reads the current counter value and stores the value in a register.
② Drop the counter value: the number of filters read is less than the number of filters set.
③ Record the counter value to the compared stack area for the entering-work-station ones, when the signal is
stable.
④ Record the counter value to the compared stack area for the leaving-work-station ones, when the signal is
stable.
⑤ The number of filters

6_
14. When the signal is rising- or falling-edge triggered, and the PLC completes processing the filters, the PLC reads the
high-speed counter value and adds one in the value of the head index. The PLC then records the entering and
leaving counter results for each work station. The compared counter result is the current counter value + reference
value + observational error. For either rising- or falling-edge triggered, the value of the head index is incremented.
The maximum value for the head index mx2 (the maximum number of objects).
15. The value of the head index is cyclically incremented, when the signal is rising- or falling-edge triggered and
completes processing the number of filters (the default for trigger input is OFF). The maximum value for the head
index is mx2 (the maximum number of objects). For example, if you set the number of objects to 10, the value of the
head index (default: 0) is incremented to 1, 2, 3 to 20 and then 1, 2, 3 to 20 repeatedly. When the value of the head
index is 0, it means no object has entered after executing the instruction. The PLC adds one to the value of the head
index, and then checks the value of the tail index. If the value (after adding one) in the value of the head index equals
the value of the tail index, the PLC cancels the addition and records the counter result.
16. When the instruction is executed and the state of the initial input is OFF, the rising-edge trigger corresponds to the
odd numbers of the head index value, and the falling-edge trigger corresponds to the even numbers of the head
index value.
6-221
17. When the PLC executes the instruction and the state of the initial input is ON, the falling-edge trigger corresponds
to the odd numbers of the head index value, and the rising-edge trigger corresponds to the even numbers of the
head index value.
18. When the PLC executes the instruction, it does not clear the values in the accumulated area and the index areas. If
the data is in a latched area and needs to be enabled again, use the ZRST instruction to clear the values in the head
and tail indexes.
Example
Refer to the example in the YOUT instruction (API 0710) for more information.
_6
6-222

Comparing the outputs of multiple work
0710 YOUT S1，S2，S3，D
stations

S1 
S2 
S3 
D  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
S3  
D 

－ AS －
Symbol
Setting for the number for work

S2 ：
stations and objects
First corresponding device for the
S3 ：
comparison result in the stack area
D ：
First corresponding device for the 6_
output work station
Explanation
1. This instruction is only available for AS Series PLCs with firmware version 1.04.00 or higher. The instruction cannot
be used in the ST programming language, interrupt tasks or function block which is called only once.
2. S1 is for the setting of the high-speed counter. Use the same settings for the high-speed counter as for the high-
speed counter for the XCMP instruction.
3. S2 occupies two consecutive 16-bit devices. S2+0 is n (the work station number) and S2+1 is m (the maximum number
of objects). The range for n and m is between 1–32 for PLC with FW V1.04.00 (V1.04.00 included) or previous
versions. And the range for n and m is between 1–64 for PLC with FW V1.06.00 (V1.06.00 included) or higher
versions. When the value is out of range, the value used is the maximum (32) or the minimum (1). The settings for
the operands should be the same as for the XCMP instruction.
4. S3 is first corresponding device for the comparison result in the stack area. S3 occupies 2xn consecutive 16-bit
devices and 2xmxn consecutive 32-bit devices (or 4xmxn consecutive 16-bit devices). For information on the
functions of each device and the corresponding number for D, refer to the XCMP instruction (API 0709). It is
suggested that you use the same variable as you use for the XCMP instruction.
6-223
5. There is no limit on the number of times you can execute the instruction but only one execution can be done at a
time.
6. It is suggested that you use with the XCMP instruction, and use the same first corresponding device for the
comparison result in the stack area (S3).
7. D is only for the outputs of Y and M devices; Y and M should be the BOOL data type. It occupies a consecutive
number of work stations Xn. When used as the output point of Y or the M device, the instruction refreshes the output
states.
8. The odd numbered head index values (for example 1, 3, 5,…) are the compared counter results for the object when
entering (Compared stack areas for the entering -work-station ones). The even numbered head index values (for
example 2, 4, 6,…) are the compared counter result of the object when leaving (Compared stack areas for the
entering -work-station ones).
9. When the compared counter result for entering and leaving in the stack area are 0, the actions in this area are not
executed and the state of the corresponding output work station is OFF. Add 2 to the value of the tail index and the
added value in the tail index should not exceed the value of the head index.
10. When the YOUT instruction is executed, each work station checks the compared value for entering and leaving in
the tail index. When the counter value is larger or the same as the compared value for entering, the corresponding
output point is ON and adds 1 to the value of the tail index. When the counter value is larger or the same as the
compared value for leaving, the corresponding output is OFF and adds 1 to the value of the tail index; but the value
of the tail index (after adding 1) does not exceed the value of the head index.
_6
Example: three work stations and up to four objects
Wo rk Work Work
station station station
Object 1 2 3
detection
Obj ect
En co der
Step 1: use the input point X0.4 as the object detection interrupt, HC202 as the high-speed counter for the encoder and
output point Y0.0 as the first output point for the work station.
6-224
Step 2: edit the register to set up the reference values, and the observational error when entering and leaving.
Device D D500 D502 D504
Reference value for comparison (32-bit) K2000 K3000 K4000
Observational error when entering (32-bit) K100 K120 K130
Observational error when leaving (32-bit) K50 K-20 K20
Device D D2000 D2001 D2002
Value of the head index (16-bit) K0 K0 K0
Device D D2003 D2004 D2005
Value of the tail index (16-bit) K0 K0 K0
Step 3: set up the initial values and write the programs.
6_
6-225
Set up three work stations for D0, 4 objects for D1 and 50 filters for D2. After the contact M0 is activated, the system sets
the object detection, the compared values, the compared counter result of the object entering and leaving, and the output
controls for each work station. For example, the system detects two objects have entered and then four triggers to read
the compared counter results: 3000, 3500, 4500, and 5000 in HC202 (HC202=K5060). The following table shows the
compared value and the head/tail index in the stack area.
Device D D2000 D2001 D2002
Value of the head index (16-bit) K4 K4 K4
_6 Device D number D2003 D2004 D2005
Value of the tail index (16-bit) K1 K1 K1
Device D number D2006 D2008 D2010
Compared stack area 1 for the entering -work-

K5100 K6120 K7130
station ones (32-bit)
Compared stack area 1 for the leaving-work-

K5550 K6480 K7520

K6600 K7620 K8630

K7050 K7980 K9020
6-226

K0 K0 K0

K0 K0 K0
The following table shows the state of the output point Y when the high-speed counter HC202 reaches 5200.
Output point Y number Y0.0 Y0.1 Y0.2
16-bit value ON OFF OFF
Value of the head index

K4 K4 K4
(16-bit)
Value of the tail index

K2 K1 K1
(16-bit)
The following table shows the state of the output point Y when the high-speed counter HC202 reaching 6200.
6_
16-bit value OFF ON OFF

K4 K4 K4
(16-bit)
D2003 D2004 D2005

Device D number

K3 K2 K1
(16-bit)
6-227
16-bit value ON OFF OFF

K4 K4 K4
(16-bit)

K4 K3 K1
(16-bit)
16-bit value OFF OFF ON
D2002
Device D number D2000 D2001

K4 K4 K4
_6 (16-bit)

K4 K3 K2
(16-bit)
16-bit value OFF ON OFF

K4 K4 K4
(16-bit)

K4 K4 K3
(16-bit)
6-228
Output state OFF OFF OFF

K4 K4 K4
(16-bit)

K4 K4 K3
(16-bit)
Output state OFF OFF ON

K4 K4 K4
(16-bit)
6_

K4 K4 K4
(16-bit)
6-229
0711 D SUNRS P Longi ~ SSec Sunrise and sunset times

Longi  
Lati  
TimeZ  
DST    
Year  
Month  
Date  
RHour 
RMin 
RSec 
SHour 
SMin 
SSec 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Longi 
Lati 
TimeZ  
DST 
_6 Year  
Month  
Date  
RHour  
RMin  
RSec  
SHour  
SMin  
SSec  

AS AS
Symbol
Longi ： Longitude (REAL type)
Lati ： Latitude (REAL type)
TimeZ ： Time zone(integer) (-12 ~ +14)
DST ： Daylight saving time
Year Year
Month Month
6-230
SUNRS Date Date

EN
Longi RHour
Lati RMin
RSec
TimeZ
SHour The hour to sunrise on the set date
DST RHour
SMin (24 hour time format)
Year
SSec
Month
Date
RMin The minute to sunrise on the set date
RSec The second to sunrise on the set date

The hour to sunset on the set date
SHour
(24 hour time format)
SMin The minute to sunset on the set date
SSec The second to sunset on the set date
Explanation
1. The instruction works with the AS series PLC firmware V1.04.50 or later. The sunrise and sunset times may not be
as accurate as the local weather report publishes because the values that you have entered may be incorrect or the
altitude of where the device is installed may interfere with the accuracy. When the result is not as accurate, you can
adjust the values manually. After self-evaluation, the error range of this instruction is less than 5 minutes.
2. Enter values for the local longitude and latitude in numbers. For example, the longitude and latitude of Taoyuan,
Taiwan is 121.30098 and 24.99363. Latitudes north of the Equator are denoted by a positive sign. Latitudes south
6_
of the Equator are given negative values.
3. Enter values for the local time zone, ranging from -12 to +14. The time zone cannot be calculated through the set
longitude and latitude; if the setting is out of range or the value is incorrect, no error message will be shown.
4. When the daylight saving time is enabled (ON), the instruction checks if the daylight saving time on the PLC is
enabled. When the daylight saving time is enabled on the PLC, DST time will be added on the sunrise and sunset
times.
5. Enter values for the local date, month, and year in decimal format. Make sure you have entered correct values. The
instruction does not check if the values are correctly entered.
6. After calculation, the instruction output the hour, minute and second to sunrise and sunset in integer, in decimal
format and 24 hour time format.
Example
Calculate the time to sunrise and sunset in Taoyuan, Taiwan on January 1st, 2018. The official time zone in Taiwan is
defined by an UTC offset of +08:00. And daily saving time is NOT implemented in Taiwan.
After calculation, the time to sunrise is at 06:39:47 and the time to sunset is at 17:16:42. See the example program below.
6-231
Checked with the official weather website, the actual sunrise occurred at 06:39:44 and the actual sunset occurred at
17:16:45. The difference between the PLC calculation and the actual occurrence is ±3 seconds.
_6
6-232
6.9 Logic Instructions

6.9.1 List of Logic Instructions
The following table lists the Logic instructions covered in this section.

API Function
0801 MAND –  Matrix AND operation
0802 WOR DOR  Logical OR operation
0803 MOR –  Matrix OR operation
0805 MXOR –  Matrix exclusive OR operation
0809 LD& DLD& – S1&S2
0810 LD| DLD| – S1|S2
0811 LD^ DLD^ – S1^S2
0812 AND& DAND& – S1&S2
0813 AND| DAND| – S1|S2

6_
0814 AND^ DAND^ – S1^S2
0815 OR& DOR& – S1&S2
0816 OR| DOR| – S1|S2
0817 OR^ DOR^ – S1^S2
6-233
6.9.2 Explanation of Logic Instructions
0800 D WAND P S1, S2, D Logical AND operation

S1           
S2           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1    
S2    
D    

AS AS AS
Symbol
D ： Operation result
_6
Explanation
1. This instruction applies the logical operator AND to the binary representations in S1 and S2 It performs the logical
AND operation on each pair of corresponding bits and stores the result in D.
2. Only the DAND instruction can use the 32-bit counter.
3. The result in each position is 1 if the first bit is 1 and the second bit is 1; otherwise, the result is 0.
Example 1
When X0.0 is ON, the instruction performs the logical operation AND on each pair of corresponding bits in the 16-bit
device Y0 and the 16-bit device Y2. It stores the result in Y4.
6-234
Example 2
When X0.0 is ON, the instruction performs the logical operation AND on each pair of corresponding bits in the 32-bit
device (Y11, Y10) and the 32-bit device (Y21, Y20). It stores the result in (Y41, Y40).
6_
S1
b31 b15 b0
Before the instruction Y11 Y1 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1
is executed S2 DA ND
Y2 1 Y2 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
After the instruction D
is executed
Y4 1 Y4 0 0 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0
6-235
0801 MAND P S1, S2, D, n Matrix AND operation

S1      
S2      
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  
n  

AS AS －
Symbol
S1 ： Matrix source 1
_6 n ： Length of the array
Explanation
1. This instruction applies the logical operator MAND to the n rows of binary representations in S1 and the n rows of
binary representations in S2. It performs the matrix operation AND on each pair of corresponding bits, and stores
the operation result in D.
2. The result in each position is 1 if the first bit is 1 and the second bit is 1; otherwise, the result is 0.
Example
When X0.0 is ON, this instruction performs the matrix operation AND on each pair of corresponding bits on the data in
the 16-bit devices Y0–Y2 and the data in 16-bit devices Y10–Y12. It stores the result in the 16-bit devices Y20–Y22.
6-236
S1 b15 b0
Y0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1
Y1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1
Y2 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1
Before the instruction
is executed S2 b15 b0
Y10 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
Y11 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
Y12 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
D b15 b0
Y20 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
After the instruction
Y21 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
is executed
Y22 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 0
Additional remarks
1. If S1+n-1, S2+n-1, or D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error
code in SR0 is 16#2003. 6_

3. Explanation of matrix instructions:
 A matrix is composed of more than one 16-bit register. The number of registers in a matrix is the length of the
array n. There are 16×n bits in a matrix, and the matrix operation is performed on one bit at a time.
 The matrix instruction takes the 16×n bits in a matrix as a string of bits, rather than as values. The matrix
operation is performed on each bit.
 Matrix instructions mainly process the one-to-many or many-to-many status, such as moving, copying,
comparing, and searching by bit.
 You must specify a 16-bit register for the matrix instruction. The 16-bit register specifies a certain bit among
the 16n bits in the matrix for the operation, and the 16-bit register is called the pointer. The value in the
register is between 0–16n-1, and corresponds to the bit between b0–b16n-1.
 Shifting or rotating of the specified data can be involved in the matrix operation. Note that the bit number
decreases from the left to the right, as illustrated below.
6-237
Left Width: 16 bits Right
Y0 b15 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 b0
Y1 b31 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 b16
Length: n
Y2 b47 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 b32
0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
Mn-1 b16n- 1 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
 The width of the matrix (C) is 16 bits.
 Pr represents the pointer. When the value in Pr is 15, it specifies b15.
Example: The following matrix is composed of the three 16-bit devices Y0, Y1, and Y2. The data in Y0 is
16#AAAA, the data in Y1 is 16#5555, and the data in Y2 is 16#AAFF.
1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Y0
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Y1
1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 Y2
Example: The following matrix is composed of the three 16-bit devices X 0, X 1, and X 2. The data in X 0 is
_6 16#37, the data in X 1 is 16#68, and the data in X 2 is 16#45.
0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 X0
0 0 0 0 0 0 0 0 0 1 1 0 1 0 0 0 X1
0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 X2
6-238
0802 D WOR P S1, S2, D Logical OR operation

S1           
S2           
D  DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
D    

AS AS AS
Symbol
6_
Explanation
1. This instruction applies the logical operator OR to the binary representations in S1 and S2. It performs the logical
inclusive operation OR on each pair of corresponding bits, and stores the operation result in D.
2. Only the DOR instruction can use the 32-bit counter but not the device E.
3. The result in each position is 1 if the first bit is 1, the second bit is 1, or both bits are 1; otherwise, the result is 0.
6-239
Example 1
When X0.0 is ON, This instruction performs the logical inclusive operation OR on each pair of corresponding bits in the
16-bit device Y0 and the 16-bit device Y2. It stores the operation result in Y4.
b15 b0
S1 Y0 011 0 1 0 1 0 1 0 1 0 1 0 1 0 1
is executed
S2 Y2 0 0 0 0 1 1 1 1 1 0 1 0 0 1 0 1
b15 b0
Y4 0 1 0 1 1 1 1 1 1 1 1 1 0 1 0 1
is executed D
Example 2
When X0.1 is ON, the instruction performs the logical inclusive operation OR on each pair of corresponding bits in the
_6
32-bit device (Y11, Y10) and the 32-bit device (Y21, Y20). It stores the operation result in (Y41, Y40).
S1 b31 b15 b0
Before the instruction Y11 Y1 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1
is executed DO R
S2
Y2 1 Y2 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0
After the instruction D

is executed Y4 1 Y4 0 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1
6-240
0803 MOR P S1, S2, D, n Matrix OR operation

S1      
S2      
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  
n  

AS AS －
Symbol
n ： Length of the array 6_

Explanation
1. This instruction applies the logical operator OR to the n rows of binary representations in S1 and the n rows of
binary representations in S2. It performs the matrix operation OR on each pair of corresponding bits and stores the
operation result in D.
2. The result in each position is 1 if the first bit is 1, the second bit is 1, or both bits are 1; otherwise, the result is 0.
6-241
Example
When X0.0 is ON, the instruction performs the matrix operation OR on each pair of corresponding bits in the 16-bit
devices Y0–Y2 and the data in 16-bit devices Y10–Y12. It stores the operation result in the 16-bit devices Y20–Y22.
S1 b15 b0
Y0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
After the
Y1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 instruc tion
Y2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 is executed D b15 b0
Before the Y20 0 1 0 1 1 1 1 1 1 1 1 1 0 1 0 1
instruc tion S2 b15 MOR b0
is executed Y10 0 0 0 1 0 1 1 1 1 0 1 0 0 1 0 1 Y21 0 1 0 1 1 1 1 1 1 1 1 1 0 1 0 1
Y11 0 0 0 1 0 1 1 1 1 0 1 0 0 1 0 1 Y22 0 1 0 1 1 1 1 1 1 1 1 1 0 1 0 1
Y12 0 0 0 1 0 0 1 1 1 0 1 0 0 1 0 1
_6
Additional remarks
6-242
0804 D WXOR P S1, S2, D Logical exclusive OR operation

S1           
S2           
D  DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
D    

AS AS AS
Symbol
6_
Explanation
1. This instruction applies the logical operator XOR to the binary representations in S1 and S2. It performs the logical
exclusive operation OR on each pair of corresponding bits, and stores the operation result in D.
2. Only the DXOR instruction can use the 32-bit counter, but not the device E.
3. The result in each position is 1 if the two bits are different, and 0 if they are the same.
6-243
Example 1
When X0.0 is ON, the instruction performs the exclusive operation OR on each pair of corresponding bits in the 16-bit
device Y0 and the 16-bit device Y2. It stores the operation result in Y4.
b15 b0
S1 Y0 011 0 1 0 1 0 1 0 1 0 1 0 1 0 1
is executed
S2 Y2 0 0 0 0 1 1 1 1 1 0 1 0 0 1 0 1
b15 b0
After the i nstruction
Y4 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0
is executed D
Example 2
When X0.1 is ON, the instruction performs the logical exclusive operation OR on each pair of corresponding bits in the
_6
32-bit device (Y11, Y10) and the 32-bit device (Y21, Y20). It stores the operation result in (Y41, Y40).
6-244
0805 MXOR P S1, S2, D, n Matrix exclusive OR operation

S1      
S2      
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  
n  

AS AS －
Symbol
n ： Length of the array 6_

Explanation
1. This instruction applies the logical operator XOR to the n rows of binary representations in S1 and the n rows of
binary representations in of S2. It performs the matrix exclusive operation OR on each pair of corresponding bits and
stores the operation result in D.
2. The result in each position is 1 if the two bits are different, and 0 if they are the same.
6-245
Example
When X0.0 is ON, the instruction performs the matrix exclusive operation OR on each pair of corresponding bits in the
16-bit devices Y0–Y2 and the data in 16-bit devices Y10–Y12. It stores the operation result in the 16-bit devices Y20–
Y22.
S1 b15 b0
Y0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
After the
Y1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
instruc tion D
Before the Y2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 is executed b15 b0

instruc tion S2 b15 MXO R b0 Y20 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0
is executed Y10 0 0 0 1 0 1 1 1 1 0 1 0 0 1 0 1 Y21 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0
Y11 0 0 0 1 0 1 1 1 1 0 1 0 0 1 0 1 Y22 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0
Y12 0 0 0 1 0 0 1 1 1 0 1 0 0 1 0 1
Additional remarks
_6
6-246
0808 D WINV P S, D Logical reversed INV operation

S           
D        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    

AS AS AS
Symbol
S ： Data source
Explanation
1. This instruction applies the INV instruction to the data in S , and stores the operation result in D. 6_
2. Only the DINV instruction can use the 32-bit counter but not the device E.
3. This instruction performs reverse processing on the data in S. If the state of S is 0 before executing the INV
instruction, the state changes to 1 as a result of the INV instruction.
Example 1
When X0.0 is ON, the instruction performs the INV operation on the corresponding bits in the 16-bit device Y0. It stores
the operation result in the 16-bit device Y4.
6-247
Example 2
When X0.0 is ON, the instruction performs the INV operation on each pair of corresponding bits in the 32-bit devices
Y11–Y10. It stores the operation result in the 32-bit device Y41–Y40.
_6
6-248
0809- 0811 D LD＃ S1, S2 Contact type of logical operation LD＃

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      

－ AS AS
Symbol
Taking LD& and DLD& for example
Explanation
1. The instruction is used to compare the data in S1 with that in S2. When the comparison result is not 0, the condition 6_
of the instruction is met. When the comparison result is 0, the condition of the instruction is not met.
2. Only the instruction DLD＃can use the 32-bit counter but not the device E.
3. The instruction LD＃can be connected to the mother line directly.

API No. 16-bit instruction 32-bit instruction
ON OFF
0809 LD& DLD& S1&S2 ≠ 0 S1&S2 = 0
0810 LD| DLD| S1|S2 ≠ 0 S1|S2 = 0
0811 LD^ DLD^ S1^S2 ≠ 0 S1^S2 = 0
4. &: Logical AND operation
5. |: Logical OR operation
6. ^: Logical exclusive OR operation
6-249
Example
1. The logical operator AND takes the data in C0 and C1, and performs the logical AND operation on each pair of
corresponding bits. When the operation result is not 0, Y1.0 is ON.
2. The instruction performs the logical operation OR on each pair of corresponding bits in D200 and D300, when the
operation result is not 0 and X1.0 is ON, Y1.1 is ON.
3. The instruction performs logical exclusive operation XOR on each pair of corresponding bits in C201 and C200,
when the operation result is not 0, or when X1.1 is ON, Y1.2 is ON.
_6
Additional remarks
If S1 or S2 is illegal, the condition of the instruction is not met, SM0 is ON, and the error in SR0 is 16#2003.
6-250
0812- 0814 D AND＃ S1, S2 Contact type of logical operation AND＃

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      

－ AS AS
Symbol
Taking AND& and DAND& for example
Explanation
1. This instruction compares the data in S1 with that in S2. When the comparison result is not 0, the condition of the 6_
instruction is met. When the comparison result is 0, the condition of the instruction is not met.
2. Only the DAND＃instruction can use the 32-bit counter, but not the device E.
3. Connect the AND＃instruction and the contact in series.

ON OFF
0812 AND& DAND& S1&S2 ≠ 0 S1&S2 = 0
0813 AND| DAND| S1|S ≠ 0 S1|S2 = 0
0814 AND^ DAND^ S1^S2 ≠ 0 S1^S = 0
6-251
Example
1. When X0.0 is ON, the instruction performs the logical operation AND on each pair of corresponding bits in C0 and
C10. When the operation result is not 0, Y1.0 is ON.
2. When X0.1 is OFF, the instruction performs the logical operation OR on each pair of corresponding bits in D10 and
D0. When the operation result is not 0, Y1.1 is ON.
3. When X0.2 is ON, the instruction performs the logical exclusive operation OR on each pair of corresponding bits in
the 32-bit register (D200, D201) and the data in the 32-bit register (D100, D101). When the operation result is not 0,
or when X0.3 is ON, Y1.2 is ON.
_6
Additional remarks
If the value in S1 or S2 is not valid, the condition of the instruction is not met, SM0 is ON, and the error in SR0 is
16#2003.
6-252
0815- 0817 D OR＃ S1, S2 Contact type of logical operation OR＃

S1           
S2           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1      
S2      

－ AS AS
Symbol
Taking OR& and DOR& for example
Explanation
1. This instruction compares the data in S1 with that in S2. When the comparison result is not 0, the condition of the 6_
instruction is met. When the comparison result is 0, the condition of the instruction is not met.
2. Only the DOR＃ instruction can use the 32-bit counter.
3. Connect the OR＃instruction and the contact in parallel.

ON OFF
0815 OR& DOR& S1&S2 ≠ 0 S1&S2 = 0
0816 OR| DOR| S1|S2 ≠ 0 S1|S2 = 0
0817 OR^ DOR^ S1^S2 ≠ 0 S1^S2 = 0
6-253
Example
1. When X0.1 is ON, Y0.0 is ON. The instruction performs the logical operation AND on each pair of corresponding bits
in C0 and C10. When the operation result is not 0, Y0.0 is ON.
2. When X0.2 and X0.3 are ON, Y0.1 is ON. The instruction performs the logical operation OR on each pair of
corresponding bits in the 32-bit register (D10, D11) and the 32-bit register (D20, D21). When the operation result is
not 0, Y0.1 is ON. The instruction performs the logical exclusive operation OR on each pair of corresponding bits in
the 32-bit counter HC0. and the 32-bit register (D200, D201). When the operation result is not 0, Y0.1 is ON.
_6
Additional remarks
If the value in S1 or S2 is not valid, the condition of the instruction is not met, SM0 is ON, and the error in SR0 is
16#2003.
6-254
6.10 Rotation Instructions

6.10.1 List of Rotation Instructions
The following table lists the Rotation instructions covered in this section.

API Function
0900 ROR DROR  Rotating bits in a group to the right
0901 RCR DRCR  Rotating bits in a group to the right with the carry flag
0902 ROL DROL  Rotating bits in a group to the left
0903 RCL DRCL  Rotating bits in a group to the left with the carry flag
0904 MBR –  Rotating bits to the right or left in a matrix
6_
6-255
6.10.2 Explanation of Rotation Instructions
0900 D ROR P D, n Rotating bits in a group to the right

D       
n           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n    

AS AS AS
Symbol
D ： Device to rotate
n ： Number of bits in a group
_6
Explanation
1. This instruction divides the bits in the device specified by D into groups (n bits in a group), and then rotates these
groups to the right without the carry flag.
2. Only the DROR instruction can use the 32-bit counter, but not the device E.
3. For the 16-bit instruction, the value of n used must be between 1–6. For the 32-bit instruction, the value of n must
be between 1–32. When n is less than 0, the instruction is not executed. When n exceeds the range, the
instruction is executed with n at the maximum value (32) of the range.
4. In general, the RORP and DRORP pulse instructions are used.
6-256
Example
When X0.0 switches from OFF to ON, the instruction divides the values of the bits in D10 into groups (four bits in a
group), and rotates these groups to the right. The value of the bit marked ※ is transmitted to the carry flag SM602.
b 15 ※ b0
Carry flag
0 1 1 1 1 0 1 1 0 1 0 0 0 1 0 1
After the rotation is ex ecuted
b 15 b0 Carry flag
0 1 0 1 0 1 1 1 1 0 1 1 0 1 0 0 0
Additional remarks
6_
6-257

Rotating bits in a group to the right with
0901 D RCR P D, n
the carry flag

D       
n           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n    

AS AS AS
Symbol
_6
Explanation
groups to the right with the carry flag SM602.
2. Only the DRCR instruction can use the 32-bit counter, but not the device E.
3. For 16-bit instructions, the value of n used must be between 1–16. For 32-bit instructions, the value of n must be
between 1–32. When n is less than 0, the instruction is not executed. When n exceeds the range, the instruction is
executed with n at the maximum value (32) of the range.
4. In general, the RCRP and DRCRP pulse instructions are used.
6-258
Example
When X0.0 switches from OFF to ON, the instruction divides the values of the bits in D10 into groups (four bits as a
group), and then rotates these groups to the right with the carry flag SM602. The value of the bit marked ※ is
transmitted to the carry flag SM602.
Carry flag
b 15 ※ b0
0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 1
After the rotation is executed
Carry flag b 15 b0
0 1 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0
Additional remarks
6_
6-259
0902 D ROL P D, n Rotating bits in a group to the left

D       
n           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n    

AS AS AS
Symbol
_6
Explanation
groups to the left.
2. Only the DROL instruction can use the 32-bit counter, but not the device E.
3. For 16-bit instructions, the value of n must be between 1–16. For 32-bit instructions, the value of n must be
4. In general, the ROLP and DROLP pulse instructions are used.
6-260
Example
group), and then rotates these groups to the left. The value of the bit marked ※ is transmitted to the carry flag SM602.
Carry flag b 15 ※ b0
1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
After the rotation is executed
Carry flag b 15 b0
1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1
Additional remarks
6_
6-261

Rotating bits in a group to the left with the
0903 D RCL P D, n
carry flag

D       
n           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n    

AS AS AS
Symbol
_6
Explanation
1. This instruction divides the bits in the device specified by D into groups (n bits in a group) , and then rotates these
groups to the left with the carry flag SM602.
2. Only the DRCL instruction can use the 32-bit counter, but not the device E.
3. For 16-bit instructions, the value in n must be between 1–16. For 32-bit instructions, the value of n must be
4. In general, the RCLP and DRCLP pulse instructions are used.
6-262
Example
group), and then rotates these groups to the left with the carry flag SM602. The value of the bit marked ※ is transmitted
to the carry flag SM602.
Carry flag ※
b 15 b0
0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
After the r otation is ex ec uted
Carry flag
b 15 b0
1 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 1
Additional remarks
6_
6-263

Rotating bits in a group to the right or the
0904 MBR P S, D, n
left in a matrix

S      
D    
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D  
n  

AS AS －
Symbol
S ： Matrix source
Explanation
_6 1. This instruction rotates the values of n rows of bits in S to the right or to the left. When SM616 is OFF, the
instruction rotates the values of the bits to the left. When SM616 is ON, the instruction rotates the values of the bits
to the right. The instruction fills the vacancy resulting from the rotation with the value of the bit rotated last, and
stores the operation result in D. The value of the bit rotated last not only fills the vacancy, but also is transmitted to
the carry flag SM614.
2. For 16-bit instructions, the value of n must be between 1–16. For 32-bit instructions, the value of n must be
3. In general, the MBRP pulse instruction is used.
6-264
Example 1:
When X0.0 is ON and SM616 is OFF, the instruction rotates the values of the bits in the 16-bit registers D0–D2 to the left,
and stores the operation result in the 16-bit registers D20–D22. The value of the bit marked ※ is transmitted to the carry
flag SM614.
Before the rotation

S
is executed b15 b0
1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D0
Carry flag
1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D1
S M614 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D2
※
After MB R is executed
D
SM616=0 b15 b0
After the rotation 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D20
to the left is executedCarry flag 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D21
S M614 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 D22
6_
Example 2:
When X0.0 is ON and SM616 is ON, the instruction rotates the values of the bits in the 16-bit registers D0–D2 to the
right, and stores the operation result in the 16-bit registers D20–D22. The value of the bit marked ※ is transmitted to the
carry flag SM614.
6-265
Before the rotation S Carry flag

is executed b15 ※ b0
D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 SM614
D1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
D2 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
MBR
SM616=0 D
b15 b0 Carry flag
After the rotation D20 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
to the left is exec uted 0
D21 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D22 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
SM614
Additional remarks
1. If S+n-1 or D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
2. Instruction flags:
SM614: The carry flag for the matrix rotation/shift/output
SM616: The direction flag for the matrix rotation/shift
_6
6-266
6.11 Timer and Counter Instructions

6.11.1 List of Timer and Counter Instructions
The following table lists the Timer and Counter instructions covered in this section.

API Function
1000 RST DRST – Resetting a contact to OFF or clearing the value in a register.
1001 TMR – – 16-bit timer (Unit: 100ms)
1002 TMRH – – 16-bit timer (Unit: 1ms)
1003 CNT – – 16-bit counter
1004 – DCNT – 32-bit counter (including the use of high-speed counters)
1005 – DHSCS – Setting high-speed comparison
1006 – DHSCR – Resetting high-speed comparison
1007 – DHSZ – High-speed input zone comparison
1008 – DSPD – Detecting speed
1009 PWD – – Detecting pulse width
– Capturing the high-speed count value in an external input

1010 – DCAP
interrupt
6_
1011 TMRM – – 16-bit timer (Unit: 10ms)
1012 IETS –  The start of the instruction execution time measurement
1013 IETE –  The end of the instruction execution time measurement
1014 – DHSCY – Cyclic counting, comparing and outputting
1015 PPDT – – Detecting the time difference between two phases
6-267
6.11.2 Explanation of Timer and Counter Instructions
Resetting a contact or clearing a

1000 D RST D
register

D          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S        

－ AS AS
Symbol
D ：Device to reset
_6 Explanation
1. This instruction clears the values in a 32-bit HC device or two consecutive 16-bit D devices. For other devices, use
the RST instruction to clear the values.
2. The following table shows the actions of the RST instruction.
Device State
Bit Sets the coil and contact to OFF.
T，C Set the current timer value and counter value to 0, and sets the coil and contact to OFF.
Word Clears the 16-bit content value to 0.
DWord，HC，Real Clears the 32-bit content value, including floating point numbers, to 0.
3. If the RST instruction is not executed, the state of the device specified by D is unchanged.
4. The instruction supports direct output.
6-268
Example
When X0.0 is ON, the instruction sets Y0.5 to OFF.
The instruction clears the 32-bit D1 and D0 to zero when X0.0 is ON.
6_
6-269
1001 TMR S1, S2 16-bit timer (100ms)

S1 
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  

－ AS －
Symbol
S1 ： Timer number
S2 ： Setting value of the timer
Explanation
_6 Refer to the explanation of the TMRH instruction (API 1002) for details.
6-270
1002 TMRH S1, S2 16-bit timer (1ms)

S1 
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  

－ AS －
Symbol
S1 ： Timer number
S2 ： Setting value for the timer
Explanation
1. The TMR instruction uses 100ms as the timing unit in the timer, while, the TMRH instruction uses 1ms as the timing 6_
unit in the timer.
2. The value of S2 for both the TMR and TMRH instructions is between 0–32767.
3. If you use the same timer repeatedly in the program, including using it in different TMR and TMRH instructions, the
timer that completes the measurement first will be the only one that counts.
4. The T timer resets to zero automatically when the conditional contact changes from ON to OFF.
5. When you add the letter S in front of the device T, the timer in the instruction TMR is an accumulative timer. When
the conditional contact is OFF, the value of the accumulative timer is not cleared. When the conditional contact is
ON, the timer counts from the current value. Use the RST instruction with the ST accumulative timer when you want
to clear the value of the timer.
6. If you use the same T timer in the program, it is OFF when one of the conditional contacts is OFF.
7. If you use the same T timer for T and ST in the program, T is OFF when one of the conditional contacts is OFF.
8. When the instruction TMR is executed, the specified timer coil is ON and the timer begins to count. As the value of
the timer matches the setting value, the contact is ON.
6-271
9. The timers T0–T411 are defined as general timers, and T412–T511 are subroutine timers by default. Use the
hardware configuration software HWCONFIG if you need to change the ranges of the two types of timers.
10. The general timers compare the timing values when the TMR instruction is scanned. The system applies the timer
to the condition every time the TMR instruction status is scanned.
For the subroutine timers, the system counts the time and compares the timing values after the END instruction is
executed. Use subroutine timers when the TMR instruction is executed not in every scan, but you need longer lasting
timing and comparing.
Example 1 (using general type of counter; counts for 100 ms time window)
When X0.0 is ON, the instruction loads the setting value 50 to the timer T0, and T0 counts from 0 to 50. When the value
of T0 matches 50, the contact of T0 is ON.
Example 2 (using accumulative type of counter; counts for 100 ms time window)
When X0.0 is ON, the instruction loads the setting value 50 to the timer ST0. When the value of T0 is 25 and X0.0
_6 switches from OFF to ON, then T0 counts up from 25 to 50, and the contact of T0 is ON (accumulative).
Example 3 (using general type of counter; counts for 1 ms time window)
When X0.0 is ON, the instruction loads the setting value 1000 to the timer T5, and T5 counts up from 0 to 1000, and the
contact of T5 is ON.
6-272
Example 4 (using accumulative type of counter; counts for 1 ms time window)
When X0.0 is ON, the instruction loads the setting value 1000 to the timer T5. When the value of T5 is 500 and
X0.0 switches from OFF to ON, T5 counts up from 500 to 1000, and the contact of T5 is ON (accumulative).
Example 5 (using a function block in TMRH instruction)
Step 1: Declare the function block as T_Pointer.
This function block clears the value in D0 every 5 seconds.
6_
Step 2: Appoint T_Pointer as T0 in the program of unit (POU).
Additional remarks
When you declare the operand S1 in ISPSoft, select the data type TIMER for the general T timer. For an accumulative
ST timer, specify the ST device.
6-273
1003 CNT S1, S2 16-bit counter

S1 
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  

－ AS －
Symbol
S2 ： Setting value for the counter
Explanation
_6 1. This instruction changes a specified counter coil from OFF to ON, and then increments the value of the counter by
1. When the value of the counter matches the setting value, the contact of the counter is ON.
2. When the value of the counter matches the setting value, the instruction does not change the state of the contact
and value of the counter if any more counting pulses are input. Use the RST instruction (API 1000) to reset the
counter and enable counting again.
3. Refer to Example 1 below for a demonstration of using CNT instruction in a program of unit (POU). Refer to Example
2 below for a demonstration of using CNT instruction in a function block (FB).
4. You can use the same device C number of CNT instruction that used in a POU for more than once. The system will
count according to different contact status, OFF or ON separately.
5. You can NOT use the same device C number of CNT instruction that used in a FB for more than once. It is suggested
to use only 1 device C number for FW V1.07.00 (excluded) or prevision versions. For FW V1.07 or later version, you
can us up to 8 identical device C number of CNT instruction that used in a FB.
6-274
Example 1 (using CNT instruction in a POU)
When SM408 is ON for the first time, the instruction loads the setting value 10 to the counter C0 and the counter begins
counting. After SM408 switches from OFF to ON ten times, the value in C0 is 10 and the contact of C0 is ON. After C0 is
ON, if SM408 continues to switch from OFF to ON, the instruction does not increase the value in C0 after it reaches the
setting value for C0.
Example 2 (using a function block in CNT instruction)
Step 1: Declare the function block as C_Pointer.
This function block
6_
Step 2: Appoint C_Pointer as C0 and C1 in a program of unit (POU).
Additional remarks
When you declare the operand S1 in ISPSoft, select the data type COUNTER.
6-275
1004 DCNT S1, S2 32-bit counter

S1 
S2   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1
S2  

－ - AS
Symbol
S1 ： Counter value
S2 ： Setting value for the counter
Explanation
_6 1. This instruction enables the 32-bit counter between HC0–HC255.
2. If you declare the operand S1 in ISPSoft, you cannot select the CNT data type; instead, specify an HC device number.
3. For the count-up/count-down counters HC0–HC63, when the conditional contact of this instruction switches from
OFF to ON, the counters count up by incrementing the values by 1 when SM621–SM684 are OFF or count down by
decrementing the values by 1 when SM621–SM684 are ON.
4. Count-up counters HC64–HC199 count up by increasing the values by 1 when the conditional contact of the DCNT
instruction switches from OFF to ON.
5. The counter stops counting when the DCNT instruction is OFF, but the instruction does not clear the original count
value. Use the RST instruction to clear the count value and reset the contact to OFF.
6. Refer to Example 2 of CNT instruction for a demonstration of using DCNT instruction in a function block (FB).
7. Refer to the following pages for details on the high-speed counter HC200–HC255. Whenever PLC scans this
instruction, it refreshes the appointed counter for its updated values. Thus it is suggested to use this instruction in a
POU. NOTE: The number of the high-speed can NOT be duplicated.
6-276
8. Since AS Series PLC is with various built-in input types, different maximum input frequency are suggested. See the
table below for reference. It is possible that the maximum input frequency cannot be reached for the sinking and
souring type. If the output type is normally open (NO) and the drive current is insufficient. Refer to Chapter 5 from
AS Series Hardware Manual for more information on wiring.
Maximum Input
Model Name Input Type Input Number
Frequency
Differential X0.0 ~ X0.3 4M Hz

AS324MT-A
Sinking / Sourcing X0.4 ~ X0.11 200K Hz
AS332T-A X0.0 ~ X0.11 200K Hz

Sinking / Sourcing
AS332P-A X0.12 ~ X0.15 10K Hz
AS320T-B
Sinking / Sourcing X0.0 ~ X0.7 200K Hz
AS320P-B
AS300N-A No built-in inputs
AS228T-A X0.0 ~ X0.7 200K Hz
AS228P-A Sinking / Sourcing

X0.8 ~ X0.15 10K Hz
AS228R-A
AS218TX-A
AS218PX-A Sinking / Sourcing X0.0 ~ X0.7 200K Hz 6_

AS218RX-A
Example 1
NETWORK1:
When PLC runs, the value of the counter HC0 is cleared and the counter counts because SM621 is OFF. At this time,
SM408 is ON for the first time. So the instruction loads the setting value 10 to the counter HC0 and the counter begins
counting.
NETWORK2:
After SM408 switches from OFF to ON ten times, the value of the counter HC0 matches the setting value 10, and the
contact of HC0 is ON. After HC0 is ON, the value of the counter keeps increasing because SM408 continues to change
from OFF to ON even though the value of HC0 has reached the setting value.
NETWORK3:
When HC0 continues to count up and the value reaches the setting value 20, the counter counts down because SM621
is ON in the program. After SM408 switches from OFF to ON ten times and the value of HC0 decreases from 10 to 9, the
contact of HC0 is OFF.
After the contact of HC0 is OFF, the value of HC0 still continues to decrease because SM408 continues to change from
OFF to ON.
6-277
Additional remarks
For setting the mode of SM621–SM684, refer to the explanation of the 32-bit counter HC in Chapter 2.
Example 2
NETWORK1:
_6 When PLC runs, set the value of the counter HC202 to four time frequency (mode setting should be set before executing
the DCNT instruction). And then the value of the counter HC202 is cleared.
NETWORK2:
After the value of the counter HC202 reached the setting value 1000, the contact of HC202 is ON.
6-278
Explanation of the high-speed counter:

AS Series high-speed counters can be divided into hardware counters (up to a maximum of 200KHz input, and for
differential input points up to 4MHz) and software counters (up to a maximum of 10KHz). Refer to hardware specification
for more details on the input limit.
Hardware counter
Input X0.
HC No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
HC200 P#1 R#4
HC201 P D#1 R
HC202 A#1 B#1 R
HC203 --#2 -- --
HC204 P R
HC205 P D R
HC206 A B R
HC207 -- -- --
HC208 P R
HC209 P D R
HC210 A B R 6_
HC211 -- -- --
HC212 P R
HC213 P D R
HC214 A B R
HC215 -- -- --
HC216 P
HC217 P D
HC218 A B
HC219 -- --
HC220 P
HC221 P D
HC222 A B
HC223 -- --
6-279
Note 1: P: single-phase pulse input, D: Direction signal input, A and B: two phase two input, R: Reset signal input. Only
one out of four input modes can be used in PLC programing. For example, if HC200 is edited, the HC20-HC203 can no
longer be edited.
Note 2: -- indicates that the counting mode is reserved and not available now. An empty box indicates no function.
Note3: refer to the SM/SR table for count up/down state selection and the number of times for frequency input.
Note 4: the R function (reset input) is disabled by default. Refer to the SM/SR comparison table for how to use R.
Take HC200 for example. SM291 switches to ON to start the R function and then the rising edge of X0.12 triggers
clearing the value of HC200. If there is no built-in input points, including X0.12 ~ X0.15, in the PLC you are using, you
can use external interrupts or use counter eraser instructions to clear the counters.
Software counter:
Input X0.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
HC No.
HC232 P
HC233 P D
HC234 A B
_6 HC235 UP#5 DN#5
HC236 P
HC237 P D
HC238 A B
HC239 UP DN
HC240 P
HC241 UP DN
HC242 P
HC243 UP DN
HC244 P
HC245 UP DN
HC246 P
HC247 UP DN
HC248 P
6-280
HC249 UP DN
HC250 P
HC251 UP DN
HC252 P
HC253 P
Note 5: UP: single phase count-up input (same as CW), DN: single phase count-down input (same as CCW)
The high-speed counters between HC200–HC255, are reserved devices inside PLC and are not listed in this table. It is
not recommended to use these counters in a program. If there is no built-in input points, including X0.12 ~ X0.15, in the
PLC you are using, do NOT use their corresponding counters.
The following table lists the high-speed counter, function, reset, reversing, and counting mode.
Starting the Reversing the Counting

Count-up/count-down function
Reset function direction mode
HC No. SM No. Attribute Explanation SM No. SM No. SR No.
HC200 SM300 R/W Show/ set SM281
HC201 SM301 R Show SM291 (Applicable for HC201, SR190
HC202 SM302 R Show HC202#7)


6_


HC217 SM317 R Show -- (Applicable for HC217, SR194

HC232 SM332 R/W Show/ set

SM287
HC235 SM335 R Show
SM288
HC239 SM339 R Show
HC240 SM340 R/W Show/ set Supports one
HC241 SM341 R Show time
-- --
HC242 SM342 R/W Show/ set frequency
HC243 SM343 R Show and rising
6-281
Starting the Reversing the Counting

Count-up/count-down function
Reset function direction mode
HC No. SM No. Attribute Explanation SM No. SM No. SR No.
HC244 SM344 R/W Show/ set edge –
triggered
HC245 SM345 R Show
counting only
Supports one
time
frequency
HC246 SM346 R/W Show/ set -- -- and rising
edge –
triggered
counting only
HC247 SM347 R Show
HC248 SM348 R/W Show/ set Supports one
HC249 SM349 R Show time
HC250 SM350 R/W Show/ set frequency
-- -- and rising
HC251 SM351 R Show
edge –
triggered
HC253 SM353 R Show counting only
Note 1: All SM special flags in the above table are OFF by default.
Note 2: When SM under “Count-up/count-down function” is OFF, it indicates that the corresponding counter counts up or
displays that it is counting up. If SM is ON, it indicates that the corresponding counter counts down or displays that
it is counting down.
Note 3: The “ under Attribute indicates “Read only” and R/W indicates “Read/Write”.
_6
Note 4: The SR special registers under “Counting mode” are 1 time frequency input by default. Use 2 for the input value
for double frequency and 4 for four times frequency. Four times frequency is only applicable to the A/B 2-phase
input counter. If the input value is not 1, 2 or 4 in SR, this indicates that the PLC uses one times frequency.
Note 5: All single-phase counters in the table count using one times frequency, and the rising-edge counting mode
changes the input point from OFF to ON.
Note 6: P (Pulse input) and D (Direction) counters can reverse direction. When SM is ON, the counting direction
(up/down) is reversed. For example, when the preset direction input is OFF, the counter counts up. When SM
switches to ON, the counter changes to count down.
Note 7: Available for FW V1.08 or later.
6-282
1005 D HSCS S1, S2, D Setting high-speed comparison

S1 
S2   
D   
DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D 

－ - AS
Symbol
S2 ： Comparative value
Explanation 6_
1. Use this instruction with high-speed counters with numbers HC200 and above. If the value in the high-speed counter
specified by S1 changes by increasing or decreasing by 1, the DHSCS instruction makes the comparison
immediately. When the current value of the high-speed counter is equal to the comparative value specified in S2, the
device specified by D changes to ON. After that, the device specified by D remains ON even if the comparison result
is that the current value and the comparative value are not equal.
2. If the device specified by D is Y0.0–Y0.15, and the value of S2 is equal to the current value , the comparison result of
the high-speed counter is output to the output terminals Y0.0–Y0.15. Other Y devices are affected by the scan cycle,
but this instruction updates all devices immediately and is not affected by the scan cycle. For PLC with FW V1.06.00
(V1.06.00 included) or later versions, devices Y0.12 ~ Y0.15 are affected by the scan cycle.
3. The D operand can also specify an I interrupt device between 1200–1267.
4. The high-speed counters are divided into software counters and hardware counters. The available high-speed
comparators and interrupt device numbers are listed in the following table.
6-283
Type Range of counter High-speed comparator High-speed interrupt
numbers number device number
HC200 - HC203 Comparator: I200-I203
HCC00-HCC03
HCC04-HCC07
HCC08-HCC11
Hardware counter
HCC12-HCC15
HCC16-HCC19
HCC20-HC223
Software counter HC232 - HC253 - I260-I267
5. Explanation of the hardware comparators for DHSCS, DHSCR, DHSCY and DHSZ instructions:
 Every one group of hardware counters shares 4 high-speed comparators. One DHSCS, or DHSCR
instruction occupies 1 high-speed comparator. One DHSZ, DHSCY instruction uses 2 high-speed
_6 comparators.
 During program editing, every group of hardware counters can use 4 high-speed comparators at most for
DHSCS, DHSCR, DHSCY or DHSZ instructions; otherwise, a syntax error occurs.
6. Explanation of the software comparators for DHSCS, DHSCR and DHSCY instructions:
 There are 8 software comparators to compare the Set or Reset function. Each DHSCS, DHSCR or DHSCY
instruction uses one high-speed comparator.
 The software comparators compare the interrupt by assigning a corresponding software comparator
according to the interrupt numbers. Note that the same interrupt number cannot be used repeatedly.
 For DHSCS, DHSCR or DHSCY instructions, the number of Set or Reset comparators cannot exceed eight
occurrences in the program; otherwise, a syntax error occurs.
7. Explanation of the software comparators for DHSZ instruction:
 There are eight software comparators for the zone comparison. One DHSZ instruction uses one comparator.
 DHSZ instruction can use a maximum of eight software comparators; otherwise, a syntax error occurs if
more than eight comparators are used.
8. The instructions DHSCS, DHSCR, DHSCY and DHSZ cannot be used in the ST programming language, interrupt
tasks or function block which is called only once.
6-284
Example 1
When M0 is ON, the DHSCS instruction is executed.
When the current value of HC200 changes from 99 to 100 or from 101 to 100, Y0.10 is ON, which outputs to the external
output terminal Y0.10 in real time, and remains ON.
Example 2
The Y output of DHSCS instruction is different from the general Y output.
1. When M0 is ON, the DHSCS instruction is executed. When the current value of HC200 changes from 99 to 100 or
from 101 to 100, Y0.10 outputs its state to the external output terminal immediately, and is not affected by the
program scan time.
6_
2. When the current value of HC200 changes from 99 to100, the contact of HC200 is ON immediately. When SET
Y0.11 is executed, Y0.11 is still affected by the scan time, and outputs its state only after END is passed.
6-285
Example 3
Using an interrupt in hardware high-speed comparison.
When the current value of HC200 changes from 99 to100 or 101 to100, the program jumps to the interrupt pointer to
execute the interrupt program, and Y0.10 is ON.
Main program:
I200 interrupt program:
_6
6-286
1006 D HSCR S1, S2, D Resetting high-speed input comparison

S1 
S2   
D   
DWORD  
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D 

－ - AS
Symbol
S2 ： Comparative value
Explanation 6_
1. Use this instruction with the high-speed counter numbered HC200 and above. If the value in the high-speed counter
specified by S1 changes by increasing or decreasing, the DHSCR instruction makes the comparison immediately.
When the current value of the high-speed counter is equal to the comparative value specified in S2, the device specified
by D changes to OFF. After that, the device specified by D remains OFF even if the comparison result is that the
current value and the comparative value are not equal.
2. If the device specified by D is Y0.0–Y0.15, and the comparative value of S2 is equal to the current value of the counter,
the comparison result is output to the external output terminals Y0.0–Y0.15. Other Y devices are affected by the scan
cycle, but this instruction updates all devices immediately and is not affected by the scan cycle.
3. The D operand can also specify the HC device to reset, and is limited to the condition in which the high-speed counter
number is the same as that of S1.
4. Refer to the DHSCS instruction (API 1005) for more information.
6-287
Example 1
1. When M0 is ON and HC200 changes its current value from 99 to 100 or from 101 to 100, Y0.10 is reset to OFF.
2. When HC200 changes its current value from 199 to 200, the contact of HC200 is ON and Y0.11 is ON, but the
output is delayed by the program scan time.
Example 2
If you specify HC200 as the hardware high-speed counter of the same number, the contact of HC200 is reset to OFF
when HC200 changes its current value from 999 to 1000 or from 1001 to 1000.
_6
1 00 0
2 00
not affec ted b y the s can ti me

HC2 00
affected by the s can ti me
6-288
1007 D HSZ S1, S2, S3, D High-speed input zone comparison

S1 
S2   
S3   
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
S3  
D 

－ - AS
Symbol
Lower bound of the comparison
S2 ：
zone
Upper bound of the comparison
S3 ：
zone
D ：
Comparison result (3 consecutive
devices)
6_
Explanation
1. Use this instruction with the high-speed counter numbers HC200 and above. The lower bound of S2 must be less
than the upper bound of S3. If you do not set the zone limit values properly, the PLC automatically adjusts them.
2. If S1 specifies a software counter and the specified counter changes by increasing or decreasing by 1 in value, the
DHSZ instruction makes the comparison immediately. The comparison condition and output state are shown in the
following table.
Comparison condition D+0 state D+1 state D+2 state
The count value of S1 < the lower bound (S2) ON OFF OFF
The lower bound (S2) <= the count value of

OFF ON OFF
S1 < the upper bound (S3)
The count value of S1 >= the upper bound

OFF OFF ON
(S3)
Note: You must set the lower bound (S2) to be less than the upper bound (S3). If you set the zone boundaries
incorrectly, the PLC automatically makes the adjustment.
6-289
3. If S1 specifies a hardware counter and the value of the specified counter reaches the lower bound (S2) or the upper
bound (S3), the DHSZ instruction makes the comparison immediately according to the count direction (up/down).
The comparison condition and output state are shown in the following table.
Count direction Comparison condition D+0 state D+1 state D+2 state
The count value of S1 == the

OFF ON OFF
lower bound (S2)
Count up
OFF OFF ON
upper bound (S3)

ON OFF OFF
lower bound (S2)
Count down
OFF ON OFF
upper bound (S3)
4. If the device specified by D is Y0.0–Y0.15, the comparison result is output to the external output terminals Y0.0–
Y0.15. Other Y devices are affected by the scan cycle, but this instruction updates all devices immediately and is not
affected by the scan cycle. For PLC with FW V1.06.00 (V1.06.00 included) or later versions, devices Y0.12 ~ Y0.15
are affected by the scan cycle.
5. Refer to the DHSCS instruction (API 1005) for more information on the high-speed zone comparison.
_6
Example
1. When D is specified as Y0.10, Y0.11–Y0.12 are also specified automatically.
2. The instruction compares the current value in HC200 with the upper/lower bound (1500/2000) of the comparison
zone, and one of Y0.10–Y0.12 is ON according to the comparison result.
3. When the current value in HC200 <1500, Y0.10 is ON. When 1500<= the current value in HC200<2000, Y0.11 is
ON.
When the current value in HC200>=2000, Y0.12 is ON.
6-290
1008 D SPD S1, S2, D Detecting speed

S1 
S2    
D DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D  

－ - AS
Symbol
S1 ： Counter value
S2 ： Setting value for the cycle time
D ： Number of pulses from the previous scan cycle
Explanation
1. This instruction requires that you use S1 with the DCNT instruction (API 1004) to enable the high speed counter with 6_
counter numbers above HC200 (including HC200).
2. The time units for S2 (the setting value for the cycle time) are millisecond (ms). The setting must be between 10–
1000. When the value is out of range, the PLC executes the instruction with S2 at the minimum value or the
maximum value and there are no error messages.
3. When the count reaches the setting value in S2 , this instruction stores the number of pulses in the device specified
by D, and is not affected by the PLC scan cycle.
4. This instruction has no limitation when editing, but it only allows eight sets of speed detection instructions to run
simultaneously. The system ignores the ninth set of the speed detection instruction and there are no error
messages. When executing this instruction, the setting values for the operand are recorded, and during the
execution of this instruction, you cannot edit the parameters.
6-291
Example
You can use the DSPD instruction for speed detection where there is an input pulse signal at X0.0. When M0 is ON,
the instruction updates the number of pulses counted by HC200 in D0 every 500ms.
In the following example, the value in D0 is 7500 and the actual pulse input frequency of X0.0 is 15kHz
(7500/500ms).
_6
6-292
1009 PWD S1, S2, D Detecting pulse width

S1 
S2    
D1 
D2   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D1  
D2 

－ AS －
Symbol
S1 ： Number of the input point
S2 ： Unit of measurement
Pulse width detection time (32-
D1 ：
bit value)
D2 ： Update flag 6_
Explanation
1. S1 supports the following 12 inputs, X0.0~X011, but S1 cannot share the same inputs with the high speed counter.
2. S2 is the unit of measurement. The instruction is not executed if the setting value of S2 is not a valid S2 code from the
following table.
S2 code Measurement Unit Detection range Frequency range Remark
0 1us 1Hz - 10kHz

Duty-on
1 1ms 0.02Hz - 100Hz
Odd-numbered inputs are NOT

2 10ns 10Hz - 1MHz
supported.
4 1us Cycle time 1Hz - 10kHz
5 1ms 0.02Hz - 100Hz
Other values The instruction is not executed.
6-293
3. The instruction stores the pulse width detection time (32-bit value) in D1 and the detection range is 0–100,000,000. If
the value is over the maximum value, it is processed as the maximum value. If the value is 0, that means is no input
switched from ON to OFF during the execution of this instruction.
4. D2 is the update flag. Whenever the detection of the S1 input is completed and the instruction is scanned,, the
updated flag switches to ON for one scan cycle time. You can check if the detection value has been updated with
the update flag. When the system executes the instruction for the first time, the update flag resets to OFF.
5. When the value in S2 is 0, 1 or 2, refer to the timing diagram below for the procedures performed, such as storing
detection values and updating flags during the execution of the instruction. The timer starts when the S1 input
switches from OFF to ON as it is shown in the position  of the following diagram. The instruction stores the
detection time when the S1 input switches from ON to OFF as shown in the position  of the following diagram.
enable
PWD disable    disable
S1
  
D1 0 100 101 100
D2
_6 Figure 1 Detection mode when the value in S2 is 0, 1 or 2
6. When the value in S2 is 4 or 5, refer to the timing diagram below for the procedures performed, such as storing
detection values and updating flags during the execution of the instruction. The timer starts when the S1 input
switches from OFF to ON as it is shown in the position  of the following diagram. The instruction stores the
detection time when the S1 input switches from OFF to ON as shown in the position  of the following diagram.
enable
PWD disable    disable
S1
 
D1 0 100 101
D2
Figure 2 Detection mode when the value in S2 is 4 or 5
6-294
7. This instruction has no limitation during editing, but it only allows eight sets of pulse width detection instructions to
run simultaneously. The system ignores the ninth or later sets of the pulse width detection instruction and there are
no error messages. When executing this instruction, the setting values for the operands are recorded, and you
cannot edit the parameters during execution.
8. Before executing this instruction, check the input hardware response time and the pulse time set in HWCONFIG. For
example, when the value in S2 is set to 0 or 2, that means the unit of time measurement is microseconds (μs). Set
the S1 input value to 0 to disable the Input Point Filter Time in HWCONFIG.
Example
Suppose there is a pulse signal of 10kHz in the input X0.0. When M0 is ON, the PWD instruction detects the input
signal on X0.0 with the pulse width stored in D10/D11 (32-bit data), the time unit is set to 0, and the detected pulse
width from D10 is 50µs.
6_
6-295

Capturing the high-speed count value in the
1010 D CAP S1, S2, D
external input interrupt

S1 
S2 
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D  

－ - AS
Symbol
External interrupt input point
S1 ：
number
Register for storing the captured
D ：
value
Explanation
_6 1. You can use only the 16 input points X0.0–X0.15 of the PLC in S1. Use one of these input points with the external
interrupt service program to start the function. Note that S1 cannot share the same input point with the high-speed
counter.
2. Select the high-speed counter HC device in S2. You must use the HC device with the DCNT instruction (API 1004) to
start the counting function.
3. The instruction stores the captured value from the high-speed counter (32-bit) in D when the interrupt occurs. The
instruction stores data when the interrupt occurs, and is not affected by the PLC program scanning.
4. The instruction operation is shown below. The input interrupt is triggered by the falling edge.
  When the execution of the instruction starts, the value in D does not change and you can enter the default
setting value.
  When the interrupt in S1 occurs, the instruction captures the value of the counter specified by S2 immediately
and stores it in D.
6-296
enable
DCAP disable disable
S2

S1
  
D -- 1000 2000 500
5. The instruction can start DCAP instructions for four different input points at most. If you set one input point as the
external interrupt triggered by the rising edge and falling edge, the instruction captures the value when the input is
triggered by the rising edge and by falling edge respectively, and stores the count value in the device specified by D.
When two instructions specify the same interrupt input point, the one that starts first uses the interrupt input point
first.
6. Set the HC device number in S2. It is recommended that you use the high-speed counters between HC200–HC255.
For details on the counters, refer to the explanation of the DCNT instruction (API 1004).
Example
6_
6-297
External interrupt is triggered by the rising edge at X0.7.
External interrupt is triggered by the falling edge at X0.7.
_6
6-298
Additional remarks
1. When M0 is ON, the DCAP instruction is enabled. When an external interrupt occurs at X0.7, the instruction
captures the value in HC200 and stores it in (32-bit) D0.
2. When the external input interrupt is triggered by the rising edge once, the instruction modifies E0 to 0 by setting
D100, stores the count value in D0 in D10 by modifying E0, and the value in D100 is 0+2.
3. When the external input interrupt is triggered by the falling edge one time, the instruction modifies E0 to 2 by
setting D100, stores the count value (10+E0=12) in D0 in D12 by modifying E0, and the value in D100 is 0+2.
When the value in D100 is 20, D100 is cleared to 0.
4. If the external interrupt is triggered by the rising edge and falling edge five times respectively, the instruction
captures the value 10 times and stores the captured values in D10, D12…D28.
The 1st captured value= D10
The 2nd captured value= D12
The 10th captured value=D28
The 11th captured value=D10
6_
6-299
1011 TMRM S1, S2 16-bit timer (10ms)

S1 
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  

－ AS －
Symbol
S1 ： Timer number
S2 ： Setting value for the timer
Explanation
This instruction uses 10ms as the unit of time.
_6 Refer to the explanation of the TMRH instruction (API 1002) for details.
6-300

1012 IETS P D
measurement

D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
D  

AS AS －
Symbol
D : The time measurement result
Explanation
1. The IETS instruction need be used with the API1013 IETE instruction together in order to measure the time for the
execution of the instruction in a PLC program which is specified to execute. The unit for the measured time is 1us. 6_
2. When the IETS instruction is enabled, the timing starts immediately until the IETE instruction is also executed. The
measurement result is stored in D device.
3. Minimum and maximum time measurement results are 0us and 32767us respectively. After the IETS instruction is
enabled, the PLC will automatically finish the time measurement and store the measurement result in D device if
no IETE instruction has been scanned and the PLC program scanning reaches the END instruction.
4. For the instructions IETS and IETE, there is no limit to how many of them are written in the program. But only one
set of IETS and IETE can be enabled every time the scan is executed. If IETS is enabled repeatedly for measuring
time, the timing of enabling the last IETS instruction is taken as the start of the time measurement. On the contrary,
if the execution of multiple IETE instructions is completely finished, the PLC will see the point when the first IETE
instruction is disabled as the end point when the time measurement is finished.
5. The IETS instruction is usually used to measure the running time of a PLC program such as interrupt service
program function blocks and etc. Since PLC’s time-measurement resource will be occupied as the time
measurement function is enabled, we suggest the two instructions should be removed after the measuring is
completed in order to avoid occupying the PLC resource during the normal execution.
6-301
Example
Calculate the instruction execution time based on the formula for the floating point number operation and the operation
result is stored in D100.
_6
6-302

1013 IETE P ─
measurement
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type

AS AS －
Symbol
Explanation
The IETE instruction should be used with the API1012 IETS instruction together. Refer to the explanation of the API 1012
instruction for more information.
6_
6-303
1014 D HSCY HCno ~ CurNo Cyclic counting, comparing and outputting

HCno 
CmpLen   
CmpS   
Action  
Yno  
CurNo 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data INT
type
HCno 
CmpLen  
CmpS  
Action  
Yno  
CurNo  

－－ AS
Symbol
_6 HCno ： 32-bit input counter number
CmpLen ： The length of data to be compared
CmpS ： The source value of data in 32-bit to be compared
Action ： Action to be taken when the comparison is made.
Yno ： The number of Y output point
CurNo ： The current group number that is making the comparison
Explanation
1. This instruction is available for FW V1.06.10 or later.
2. HCno: If the counter is a general one, the comparison will not begin even when the timing to execute comparison is
reached. The comparison begins only when the instruction is scanned. If the counter is a high-speed one, the
comparison begins when the timing to execute comparison is reached, not affected by the PLC scan cycle. Refer to
DHSCS instruction for more details on the usage and the restriction of the high-speed number.
3. CmpLen: To select a set of groups for comparison. The set group compares in a cyclic manner. The setting value of
the group can be between 4 and 32. If the setting value exceeds the acceptable range, this instruction is not
executed. And SM0 will be switched to ON. Error code SR0: 0x200B.
6-304
4. CmpS (supposedly set as D100), Action (supposedly set as D200), Yno (supposedly set as D300), CmpLen
(supposedly set as 6), CurNo (as it is set below).
CurNo CmpS Action Yno
(Current Group (The source value of data in 32- (Action to be taken when (The number of
Number) bit to be compared) the comparison is made.) Y output point)
1 D100 = 1000 D200 = 1 (Set) D300 = 16#04 (Y0.4)
2 D102 = 2000 D201 = 1 (Set) D301 = 16#05 (Y0.5)
3 D104 = 3000 D202 = 1 (Set) D302 = 16#06 (Y0.6)
4 D106 = 4500 D203 = 0 (Reset) D303 = 16#04 (Y0.4)
5 D108 = 5500 D204 = 0 (Reset) D304 = 16#05 (Y0.5)
6 D110 = 6500 D205 = 0 (Reset) D305 = 16#06 (Y0.6)
 CmpS: The source value of data in 32-bit integer. It takes several Dword space in CmLen. Thus it is suggested
to declare the array in the data type of Dword. The compared value is arranged in ascending order when the
source value is positive integers. The compared value is arranged in descending order when the source value is
negative integers. If the compared value is arranged not by the rules as mentioned, the instruction is not executed
and SM0 will be switched to ON. Error code SR0: 0x200B.
 Action: Action to be taken when the comparison is made. The value is in 16-bit integer and it takes one word
space in CmLen. The value “1” here means setting the output point to ON. The value “0” here means setting the
output point to OFF. Use 16#8000 to clear the counter value to 0 and restart the cyclic counting. Only use the
value 1, 0 or 16#8000 in here. It is suggested to declare the array in the data type of Word.
 Yno: The number of the Y output point, this value should be a 16-bit integer. It takes several Word space in
CmLen. The format here is hexadecimal. For example, 16#0004 means the Y0.4 output point, 16#0016 Y1.6
output point, and 16#00AF Y10.15 output point. It is suggested to declare the array in the data type of Word.
 CurNo: The current group number that is making the comparison. From the table above, you can see if the
setting value in CmLen is 1000, the CurNo. Is 1.
6_
5. When the value you use in Yno is not the CPU built-in output points, the outputting is affected by the PLC scan
cycle. If you need the immediate output, use CPU built-in output points and hardware type high-speed counter in
HCno.
6. Since this instruction is for cyclic comparing and outputting, you need to set a way to clear the counter value to 0 to
set a range for cyclic operation. It is suggested to use hardware input to set the counter to 0. Or you can also use a
setting to clear the counter. For example you need 6 groups to perform cyclic comparison. You can set the setting
value in CmpLen as 7 and you will have a 7 groups of CruNo (defined by CmpS). And then use 16#8000 as the
setting value in Action to clear HC. See the table below for reference.
D206 = 16#8000 D306 = 0
7 (CurNo=0) D112 = 8000
(Clear HC) (none)
7. When the instruction is firstly executed, it compares the current counter value to the value set in CmpS and set the
value in CurNo accordingly. See the example table in number 4. If the current counter value is 2000, that
corresponds to the value (D102 = 2000) set in CmpS and the corresponding value of CurNo is 2. From there you
know the Y0.5 is ON.
8. See the example in chronological illustration below.
  The instruction is firstly executed, comparing the current counter value (1500) and the value set in CmpS
(HC202). And set the value in CurNo to 1 and Y0.4 output to ON accordingly.
  When the current counter value reaches 2000, CurNo = 2 and Y0.5 is ON.
  When the current counter value reaches 3000, CurNo = 3 and Y0.6 is ON.
6-305
  When the current counter value reaches 4500, CurNo = 4 and Y0.4 is OFF.
  When the current counter value reaches 5500, CurNo = 5 and Y0.5 is OFF.
  When the current counter value reaches 6500, CurNo = 6 and Y0.6 is OFF.
  The external interrupt is triggered to clear. CurNo = 0 and HC202 = 0.
  When the current counter value reaches 1000, CurNo = 1 and Y0.4 is ON.
EN
Clear flag
HC202 1500 2000 3000 4500 5500 6500 0 1000
CurNo. 1 2 3 4 5 6 0 1
Y0.4
Y0.5
Y0.6
       
Cyclic comparison for illustration purpose only.

Clear Point
HC202=6500 reset Y0.6

No.6
_6
No.1 HC202=1000 set Y0.4
HC202=5500 reset Y0.5 No.5
No.2 HC202=2000 set Y0.5
HC202=4500 reset Y0.4 No.4

No.3 HC202=3000 set Y0.6
6-306
Example:
1. Define the following parameters as below.
1 D100 = 1000 D200 = 1 (Set) D300 = 16#04 (Y0.4)
2 D102 = 2000 D201 = 1 (Set) D301 = 16#05 (Y0.5)
3 D104 = 3000 D202 = 1 (Set) D302 = 16#06 (Y0.6)
4 D106 = 4500 D203 = 0 (Reset) D303 = 16#04 (Y0.4)
5 D108 = 5500 D204 = 0 (Reset) D304 = 16#05 (Y0.5)
6 D110 = 6500 D205 = 0 (Reset) D305 = 16#06 (Y0.6)
2. When M0 is ON, the instruction is executed.

  The instruction is firstly executed, comparing the current counter value and the value set in CmpS (HC202).
And set the value in CurNo to 1 and Y0.4 output to ON accordingly.
  When the current counter value reaches 2000, CurNo = 2 and Y0.5 is ON.
  When the current counter value reaches 3000, CurNo = 3 and Y0.6 is ON.
  When the current counter value reaches 4500, CurNo = 4 and Y0.4 is OFF.
  When the current counter value reaches 5500, CurNo = 5 and Y0.5 is OFF.
  When the current counter value reaches 6500, CurNo = 6 and Y0.6 is OFF.
  The external interrupt is triggered to clear. CurNo = 0 and HC202 = 0.
  When the current counter value reaches 1000, CurNo = 1 and Y0.4 is ON.
6_
External interrupt is triggered at X0.4.
6-307

Detecting the time difference between two
1015 PPDT HCno ~ CurNo
phases

XnoA 
XnoB 
PhaseT 
Exe   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
XnoA 
XnoB 
PhaseT  
Exe 

－ AS －
Symbol
XnoA ： Phase A input
XnoB ： Phase B input
Phase T ： Time differences between two phases (32-bit integer)
_6 Exe ： Timing flag
Explanation
1. This instruction is available for FW V1.06.10 or later.
2. You can only use the CPU built-in input points from X0.0 to X0.11 fro XnoA and XnoB. And the number of the input
points can NOT be duplicated. When the input points used are not from X0.0 to X0.11 or the number of the input
points are duplicated, the instruction is not executed. And SM0 will be switched to ON. Error code SR0: 16#2003.
3. When XnoA is rising-edge triggered, the timer starts timing immediately, not affected by the PLC scan cycle. When
XnoB is rising-edge triggered, the timer stops timing immediately, not affected by the PLC scan cycle. And the time
that is timed (unit: 1 us) will be stored in PhaseT, when this instruction is scanned by the PLC.
4. When the timer starts and this instruction is scanned to execute, the Exe flag will be ON. When the timer stops and
this instruction is scanned to execute, the Exe flag will be OFF.
5. Whenever this instruction is firstly activated, its initial action is to clear the value in PhaseT and set the Exe flag to
OFF.
6. XnoA is always timed before XnoB. Even if XnoB is rising-edge triggered before XnoA is triggered. If you need
XnoB to be timed before XnoA, you need to re-define XnoA, XnoB and the input points in them.
7. There is no limit to the number of times the instruction can be executed. And to use the same number of input points
is also no problem. But since PLC uses the number of input point for XnoA as the number of the internal timer. It is
NOT suggested to use two identical numbers of the input point for XnoA at the same time. Or the system will get
confused. And the timing result from the timer will be messed up.
6-308
8. See the example in chronological illustration below.
EN
XnoA
XnoB
PhaseT 0 3000 2900
Exe
    
  Whenever this instruction is firstly activated, it clears the value in PhaseT and sets the Exe flag to OFF.
  When XnoA is rising-triggered to start timing, the Exe flag will be ON.
  When XnoB is rising-triggered to stop timing, the Exe flag will be OFF and stores the timed result in PhaseT.
Example
When M0 is ON, the instruction is executed. This instruction calculates the phase time difference between X0.1 and X0.0
and stores the timed result in D0. (The timed result here is 13790 us.)
6_
6-309
6.12 Shift Instructions

6.12.1 The List of Shift Instructions
The following table lists the Shift instructions covered in this section.

API Function
1100 SFTR –  Shifting the states of devices to the right
1101 SFTL –  Shifting the states of devices to the left
1102 WSFR DWSFR  Shifting the data in word devices to the right
1103 WSFL DWSFL  Shifting the data in word devices to the left
1104 SFWR DSFWR  Shifting the data and writing it into a word device
1105 SFRD DSFRD  Shifting the data and reading it from a word device
1106 SFPO DSFPO  Reading the latest data from the data list
1107 SFDEL DSFDEL  Deleting data from the data list
1109 MBS –  Shifting matrix bits
1110 SFR DSFR  Shifting the values of the bits in registers by n bits to the right
1111 SFL DSFL  Shifting the values of the bits in registers by n bits to the left
_6
1112 BSFR –  Shifting the states of n bit devices by one bit to the right
1113 BSFL –  Shifting the states of n bit devices by one bit to the left
6-310
C ha pt er 6 A p pl i e d In s tr uc t io ns
6.12.2 Explanation of Shift Instructions
Shifting the states of devices to the

1100 SFTR P S, D, n1, n2
right

S     
D    
n1      
n2      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 
n1  
n2  

AS AS －
Symbol
S ： First device where the value is shifted
D ： First device where the value is shifted
n1 ： Length of the data to be shifted

6_
n2 ： Number of bits in a group
Explanation
1. This instruction divides the states of the n1 bit devices starting from D into groups (n2 bits in a group), and shifts
these groups to the right. This instruction then shifts the states of the n2 bit devices starting from S to the devices
starting from D to fill the vacancy.
2. In general, the SFTRP pulse instruction is used.
3. The operand n1 must be between 1–1024. The operand n2 must be between 1–n1.
Example 1
1. When X0.0 switches from OFF to ON, the instruction divides the states of the sixteen bit devices starting from M0
to M15 into groups (four bits in a group), and shifts these groups to the right.
2. The shift of the states of the bit devices to the right during a scan is shown below.
6 - 3 11
 M3-M0 → Being carried
 M7-M4 → M3-M0
 M11-M8 → M7-M4
 M15-M12 → M11-M8
 X0.3-X0.0 → M15-M12
F our bits as a group ar e shifted to the r ight.

X 0.3 X 0.2 X 0.1 X 0.0
5
M1 5 M1 4 M1 3 M1 2 M11 M1 0 M9 M8 M7 M6 M5 M4 M3 M2 M1 M0
4 3 2 1
_6
Example 2
to M15 into groups (five bits as a group), and shifts these groups to the right.
2. The shift of the states of the bit devices to the right during a scan is shown below.
 M0 → Being carried
 M5 → M0
 M10-M6 → M5-M1
 M15-M11 → M10-M6
 X0.4-X0.0 → M15-M11
6-312
F ive bits as a group is s hifted to the right.

X 0.4 X 0.3 X 0.2 X 0.1 X 0.0
5
M1 5 M1 4 M1 3 M1 2 M11 M1 0 M9 M8 M7 M6 M5 M4 M3 M2 M1 M0
4 3 2 1
Additional remarks
1. If S+n2-1 or D+n1-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
2. If n1 not between 1–1024, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
3. If n2 is not between 1–n1, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
6_
6-313
1101 SFTL P S, D, n1, n2 Shifting the states of devices to the left

S     
D    
n1      
n2      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 
n1  
n2  

AS AS -
Symbol
_6 n2 ： Number of bits in a group
Explanation
1. This instruction divides the states of the n1 bit devices starting from D into groups (n2 bits in a group), and shifts
these groups to the left. This instruction then shifts the states of the n2 bit devices starting from S to the devices
2. In general, the SFTLP pulse instruction is used.
3. The operand n1 must be between 1–1024. The operand n2 must be between 1–n1.
Example 1
to M15 into groups (four bits in a group), and shifts these groups to the left.
2. The shift of the states of the bit devices to the left during a scan is shown below.
6-314
 M15-M12 → Being carried
 M11-M8 → M15-M12
 M7-M4 → M11-M8
 M3-M0 → M7-M4
 X0.3-X0.0 → M3-M0
F our bits as a group ar e shifted to the left

X 0.3 X 0.2 X 0.1 X 0.0
5
Being c arri ed M1 5 M1 4 M1 3 M1 2 M11 M1 0 M9 M8 M7 M6 M5 M4 M3 M2 M1 M0
1 2 3 4
6_
Example 2
to M15 into groups (five bits in a group), and shifts these groups to the left.
2. The shift of the states of the bit devices to the left during a scan is shown below.
 M15 → Being carried
 M10 → M15
 M9-M5 → M14-M10
 M4-M0 → M9-M5
 X0.4-X0.0 → M4-M0
6-315
F ive bits as a group ar e shifted to the left.

X 0.4 X 0.3 X 0.2 X 0.1 X 0.0
5
Being c arri ed M1 5 M1 4 M1 3 M1 2 M11 M1 0 M9 M8 M7 M6 M5 M4 M3 M2 M1 M0
1 2 3 4
Additional remarks
SR0 is 16#2003.
2. If n1 is not between 1–1024, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
3. If n2 is not between 1–n1, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
_6
6-316

Shifting the data in word devices to the
1102 D WSFR P S, D, n1, n2
right

S      
D    
n1      
n2      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n1    
n2    

AS AS AS
Symbol
6_
Explanation
1. This instruction divides the data in the n1 word devices starting from D into groups (n2 words in a group), and shifts
these groups to the right. This instruction then shifts the data in the n2 word devices starting from S to the devices
2. In general, the WSFRP pulse instruction is used.
3. For 16-bit instruction, the operand n1 must be between 1–512. For 32-bit instruction, the operand n1 must be
between 1–256. For the application of 32-bit instruction, you need to use ISPSoft V3.09.07 or later and AS PLC
CPU FW V1.08 or later.
4. The value in the operand n2 must be between 1–n1.
6-317
Example 1
1. When M0 switches from OFF to ON, the instruction divides the data in the sixteen word devices starting from D20
to D35 into groups (four words in a group), and shifts these groups to the right.
2. The shift of the data in the word devices to the right during a scan (M0 switches from OFF to ON) is shown below.
 D23-D20 → Being carried
 D27-D24 → D23-D20
 D31-D28 → D27-D24
 D35-D32 → D31-D28
 D13-D10 → D35-D32 completed
F our r egi ster s as a group are shifted to the r ight.

_6 D1 3 D1 2 D11 D1 0
5
D3 5 D3 4 D3 3 D3 2 D3 1 D3 0 D2 9 D2 8 D2 7 D2 6 D2 5 D2 4 D2 3 D2 2 D2 1 D2 0 Being c arri ed
4 3 2 1
Example 2
to D35 into groups (five words in a group), and shifts these groups to the right.
 D20 → Being carried
 D25 → D20
 D30-D26 → D25-D21
 D35-D31 → D30-D26
6-318
F ive
Fiv re gi ters
e regis stersasas
aga roup
group are
a re shiftertoto
s hifted the
t he ri ght.
r ight.
D14 D1 3 D12 D11 D10
5
D3 5 D34 D33 D3 2 D3 1 D30 D29 D28 D2 7 D26 D25 D2 4 D2 3 D22 D 21 D2 0 Being c arried
3 1
4 2
Example 3
1. When M0 switches from OFF to ON, the instruction divides the data in the eight word devices starting from D20 to
D35 into groups (two words in a group), and shifts these groups to the right.
 D23-D20 →
6_
Being carried
 D27-D24 → D23-D20
 D31-D28 → D27-D24
 D35-D32 → D31-D28
6-319
E
Two 32-bit registers as a group are shifted to the right.
D12 D10
A B C D
Being carried
D34 D32 D30 D28 D 26 D24 D22 D20
Additional remarks
SR0 is 16#2003.
2. The n1 of the 16-bit instruction should be between1–512, and the n1 of the 32-bit instruction should be less than
256, If not, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
3. The n2 should be between 1–n1. If not, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
_6
6-320
1103 D WSFL P S, D, n1, n2 Shifting the data in word devices to the left

S      
D    
n1      
n2      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n1    
n2    

AS AS AS
Symbol
S ： First device in which the value is shifted
D ： First device in which the value is shifted
6_
Explanation
1. This instruction divides the data in the n1 word devices starting from D into groups (n2 words in a group), and shifts
these groups to the left. This instruction then shifts the data in the n2 word devices starting from S to the devices
2. In general, the WSFLP pulse instruction is used.
3. For 16-bit instruction, the value in the operand n1 must be between 1–512. For 32-bit instruction, the value in the
operand n1 must be between 1–256. For the application of 32-bit instruction, you need to use ISPSoft V3.09.07 or
later and AS PLC CPU FW V1.08 or later.
4. The operand n2 must be between 1–n1.
6-321
Example 1
to D35 into groups (four words in a group), and shifts these groups to the left.
2. The shift of the data in the word devices to the left during a scan (M0 switches from OFF to ON) is shown below.
 D35-D32 → Being carried
 D31-D28 → D35-D32
 D27-D24 → D31-D28
 D23-D20 → D27-D24
F our r egi ster s as a group ar e shifted to the l eft.

D1 3 D1 2 D11 D1 0
5
_6 Being carri ed D3 5 D3 4 D3 3 D3 2 D3 1 D3 0 D2 9 D2 8 D2 7 D2 6 D2 5 D2 4 D2 3 D2 2 D2 1 D2 0
1 2 3 4
Example 2
to D35 into groups (five words in a group), and shifts these groups to the left.
2. The shift of the data in the word devices to the left during a scan (M0 switches from OFF to ON) is shown below.
 D35 → Being carried
 D30 → D35
 D29-D25 → D34-D30
 D24-D20 → D29-D25
6-322
F ive r egi sters as a group ar e shifted to the left.

D1 4 D1 3 D1 2 D11 D1 0
5
Being c arri ed D3 5 D3 4 D3 3 D3 2 D3 1 D3 0 D2 9 D2 8 D2 7 D2 6 D2 5 D2 4 D2 3 D2 2 D2 1 D2 0
1 2 3 4
Additional remarks
SR0 is 16#2003.
2. The n1 of the 16-bit instruction should be between1–512, and the n1 of the 32-bit instruction should be less than
256, If not, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
3. The n2 should be between 1–n1. If not, the instruction is not executed, SM0 is ON, and the error code in SR0 is
6_
16#200B.
6-323

Shifting the data and writing it into a word
1104 D SFWR P S, D, n
device

S          
D    
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： Device where the data is shifted
D ： First device
n ： Data length
_6
Explanation
1. This instruction defines the data in the n word devices starting from the device specified by D as a first in-first out
list type, and takes the device specified by D as a pointer. This instruction increments the value of the pointer by
one, and writes the data in the device specified by S into the device specified by the pointer. When the value of the
pointer is larger than or equal to n-1, the instruction stops writing data, and sets the carry flag SM602 is ON.
2. In general, the SFWRP pulse instruction is used.
3. This instruction is highly used as the function of PUSH. If you need to function of POP, refer to the instructions
SFRD and SFPO for more information.
4. For 16-bit instruction, the value in the operand n must be between 2–512. For 32-bit instruction, the value in the
operand n must be between 2–256. For the application of 32-bit instruction, you need to use ISPSoft V3.09.07 or
6-324
Example 1
1. The instruction clears the value of the pointer D0 to 0 first. When M0 switches from OFF to ON, the instruction
writes the data in D20 into D1, and increments the value in D0 to 1. When M0 switches from OFF to ON again, the
instruction writes the data in D20 to D2, and increments the value in D0 to 2.
2. The instruction shifts and writes the data in the word device as shown below.
 The data in D20 is written into D1.
 The value in D0 becomes 1.
n=10
Sourc e
D20 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 6_
Pointer
D0=3 2 1
6-325
Example 2
1. The instruction clears the value of the pointer D0 to 0 first. When M0 switches from OFF to ON, the instruction
writes the data in D20/D21 into D2/D3, and increments the value in D0/D1 to 1. When M0 switches from OFF to
ON again, the instruction writes the data in D20/D21 to D4/D5, and increments the value in D0/D1 to 2.
2. The instruction shifts and writes the data in the word device as shown below.
 The data in D20/21 is written into D2/D3.
 The value in D0/D1 becomes 1.
n=5
_6 Source
D20 D8 D6 D4 D2
Pointer
D0
D0=3 2 1
Additional remarks
1. If the value in D is less than 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
2. If D+n-1 exceeds the device range, the instruction is not executed. SM0 is ON, and the error code in SR0 is
16#2003.
operand n must be between 2–256. If not, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
4. You can use the SFWR instruction with the SFRD (API 1105) instruction to write and read the data in a first in first
out (FIFO) method.
6-326

Shifting the data and reading it from a
1105 D SFRD P S, D, n
word device

S     
D    
n   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： First device
D ： Device where the data is shifted
n ： Data length
6_
Explanation
1. This instruction defines the data in the n word devices starting from the device specified by S as a first in-first out
list type, and takes the device specified by S as a pointer. This instruction decrements the value in the device
specified by S by one, writes the data in the device specified by S+1 into the device specified by D, shifts the data
in the devices specified by S+n-1–S+2 to the right, and leaves the data in the device specified by S+n-1
unchanged. When the value in the device specified by S is equal to 0, the instruction stops reading the data, and
sets the zero flag SM600 is ON.
2. In general, the SFRDP pulse instruction is used.
6-327
Example 1
1. Supposedly the value in D20 is 10, when M0 switches from OFF to ON, the instruction writes the data in D21 into
D0, shifts the data in D29–D22 one place to the right, leaves the data in D29 unchanged, and the decrements the
value in D20 by one.
2. The data in the word device is shifted and read as shown below.
 The data in D21 is read and shifted to D0.
 The data in D29-D22 is shifted one place to the right.
 The value in D20 decreases by one.
n=10
D0 D29 D28 D27 D26 D25 D24 D23 D22 D21 D20
Pointer
T he data is read.
_6
Example 2
1. Supposedly the value in D20/D21 is 5, when M0 switches from OFF to ON, the instruction writes the data in
D22/D23 into D0/D1, shifts the 32-bit data in D29–D22 one place to the right, leaves the data in D28/D29
unchanged, and the decrements the value in D20/D21 by one.
2. The data in the word device is shifted and read as shown below.
 The data in D22/D23 is read and shifted to D0/D1.
 The 32-bit data in D29-D22 is shifted one place to the right.
 The value in D20 decreases by one.
6-328
n=5
Pointer
D0 D 28 D26 D24 D22 D20
The data is read.
Additional remarks
1. If the value in S is less than 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
16#2003.
16#200B.
4. You can use this instruction with SFWR instruction (API 1104) to write and read the data in a first in first out (FIFO)
method.
6_
6-329
1106 D SFPO P S, D Reading the latest data from a data list

S    
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    

AS AS AS
Symbol
S ： First device
D ： Device where the data is stored
_6 Explanation
1. This instruction takes the device specified by S as a pointer. This instruction writes the data in the device specified
by the value of the pointer into the device specified by D and clears it to 0, and decrements the value in the device
specified by S by one. When the value in the device specified by S is equal to 0, the instruction stops reading the
data, and sets the zero flag SM600 is ON.
2. In general, the SFPOP pulse instruction is used.
3. This instruction is highly used as the function of PUSH. If you need to function of POP, refer to the instructions
SFRD and SFPO for more information.
4. For the application of 32-bit instruction, you need to use ISPSoft V3.09.07 or later and AS PLC CPU FW V1.08 or
later.
6-330
Example 1
Supposedly the value in D0 is 7, when M0 is ON, the instruction writes the data in the device specified by D0 into D10.
After the instruction shifts the data, the instruction clears the data in the device specified by D0 to 0, and decrements the
value in D0 by 1.
D S
D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
1000 7
Pointer
T he data is read.
D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
1000 0 6
Pointer
Example 2
Supposedly the value in D0/D1 is 4, when M0 is ON, the instruction writes the data in the device specified by D0/D1 into
D10/D11. After the instruction shifts the data, the instruction clears the data in the device specified by D0/D1 to 0, and
decrements the value in D0/D1 by 1. 6_
D10/D11 D8/D9 D6/D7 D4/D5 D2/D3 D0/D1

1000 4
Pointer
D10/D11 D8/D9 D6/D7 D4/D5 D2/D3 D0/D1

1000 0 3
Pointer
Additional remarks
2. If S+(the value in S) exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
6-331
1107 D SFDEL P S, D, n Deleting data from a data list

S    
D      
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： First device
D ： Device where the data is stored
n ： Device where the data is deleted
_6
Explanation
1. For this instruction, the length of the data is the value in the device specified by S, and the data itself is in the
devices specified by S+1–S+(the value in S). This instruction stores the data in the device specified by S+n in D
and deletes it, shifts the data in the devices specified by S+n+1–S+(The value in S) to the right, clears the data in
the device specified by S+(the value in S) to 0, and decrements the value in the device specified by S by one.
When the value in the device specified by S is equal to 0, the instruction stops deleting the data, and sets the zero
flag SM600 is ON.
2. In general, the SFDELP pulse instruction is used.
6-332
Example 1
Supposedly the value in D0 is 9, and n is 4. When M0 is ON, the instruction stores the data in D4 to D20. And then the
instruction deletes the data in D4. After that it shifts the data in D5–D9 to the right, and decrements the value in D0 by
one.
S
D n=4
D20 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
4712 857 123 100 111 22 48 5 799 9
T he length of the data
T he data is deleted.
D20 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
22 0 4712 857 123 100 111 48 5 799 8
Example 2
Supposedly the value in D0/D1 is 4, and n is 3. When M0 is ON, the instruction stores the data in D6/D7 to D20. And
then the instruction deletes the data in D6/D7. After that it shifts the data in D8/D9 to the right, and decrements the value 6_
in D0/D1 by one.
n=3
D20/D21 D8/D9 D6/D7 D4/D5 D2/D3 D0/D1
20000 50000 45000 40000 4
The length of the data
D20/D21 D8/D9 D6/D7 D4/D5 D2/D3 D0/D1

50000 0 20000 45000 40000 3
6-333
Additional remarks
2. If S+n exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
3. If S+(the value in S) exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
4. If n is not between 0–S, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
_6
6-334
1108 D SFINS P S, D, n Inserting data into a data list

S    
D          
n   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： First device
D ： Data to be inserted
n ： Device where the data is inserted
6_
Explanation
1. For this instruction, the length of the data is the value in the device specified by S, and the data itself is in the
devices specified by S+1–S+(the value in S). This instruction inserts the data in D into S+n, shifts the original
data in the devices specified by S+n–S+(the value in S) to the left, and increments the value in the device specified
by S by one. When the value in the device specified by S is equal to 32767, the instruction stops writing the data,
stops incrementing the value in the device specified by S, and sets the carry flag SM602 is ON.
2. In general, the SFINSP pulse instruction is used.
operand n must be between 1–16383.
4. For the application of 32-bit instruction, you need to use ISPSoft V3.09.07 or later and AS PLC CPU FW V1.08 or
later.
6-335
Example 1
Supposedly the value in D0 is 8, and n is 4. When M0 is ON, the instruction inserts the data in D200 into D4, shifts the
original data in D4–D8 to D5–D9, and increments the value in D0 by one.
D n=4 S
D200 D8 D7 D6 D5 D4 D3 D2 D1 D0
22 4712 857 123 100 111 48 5 799 8
T he data is inserted.
D200 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
22 4712 857 123 100 111 22 48 5 799 9
Example 2
Supposedly the value in D0/D1 is 4, and n is 3. When M0 is ON, the instruction inserts the data in D200 into D6/D7,
shifts the original data in D6–D9 to D8–D11, and increments the value in D0/D1 by one.
_6
n=3
D8/D9 D6/D7 D 4/D5 D2/D3 D0/D1
22000 20000 50000 45000 40000 4
D200/D201 D 10/D11 D8/D9 D6/D7 D 4/D5 D2/D3 D0/D1

22000 20000 50000 22000 45000 40000 5
Additional remarks
2. If S+n exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003
3. If S+(the value in S)+1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
4. If n is not between 0–S, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
6-336
1109 MBS P S, D, n Shifting matrix bits

S      
D    
n   DWORD       
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D  
n  

AS AS -
Symbol
S ： Matrix source
Explanation
1. This instruction shifts the values of the n rows of bits in S to the right or to the left. When SM616 is OFF, the 6_
instruction shifts the values of the bits to the left. When SM616 is ON, the instruction shifts the values of the bits to
the right. The instruction fills the vacancy (b0 when shifting to the left, and b16n-1 when shifting to the right)
resulting from the shift with the state of the borrow flag SM615.The instruction transmits the value of the bit shifted
last (from shifting to the left is b16n-1 and from shifting to the right is b0) to the carry flag SM614, and stores the
operation result in D.
3. In general, the MBSP pulse instruction is used.
Example 1
When X0.0 is ON, SM616 is OFF. The instructions shifts the values of the bits to the left. Suppose SM615 is OFF. After
the instruction shifts the values of the bits in the 16-bit registers D0–D2 to the left, it stores the operation result in the 16-
bit registers D20–D22, and SM614 is ON.
6-337
b 15 b0 Borr ow flag
D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0
Carry flag 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
D1
D2 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
After the s hift
b 15 b0
Borr ow flag
D20 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0
Carry flag D21 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
1 D22 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Example 2
When X0.0 is ON, SM616 is ON. The instruction shifts the values of the bits to the right. Suppose SM615 is ON. After the
instruction shifts the values of the bits in the 16-bit registers D0–D2 to the right, it stores the operation result in the 16-bit
registers D20–D22, and SM614 is OFF.

_6
b 15 b0 Carry flag
D0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
Borr ow flag D1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
D2 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
After the s hift
b 15 b0 Carry flag
D20 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
Borr ow flag D21 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
1 D22 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
6-338
Additional remarks
1. If S+n-1 or D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
3. Instruction flags
SM614: Carry flag for the matrix rotation/shift/output.
SM615: Borrow flag for the matrix shift/output.
SM616: Direction flag for the matrix rotation/shift.
6_
6-339

Shifting the values of the bits in registers
1110 D SFR P D, n
by n bits to the right

D       
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  
n  

AS AS AS
Symbol
D ： Device for the shift
n ： Number of bits
Explanation
1. This instructions shift the values of the bits in D by n bits to the right. The 16-bit instruction fills the vacancies (b15–
b15-n+1) resulting from the shift with 0 and the 32-bit instruction fills the vacancies (b31–b31-n+1) resulting from the
shift with 0. The value of bn-1 is transmitted to SM602.

_6
2. The operand n must be between 1–16 for 16-bit instructions and the operand n must be between 1–32 for 32-bit
instructions.
3. In general, the SFRP/DSFRP pulse instruction is used more commonly.
4. Only the DSFR/DSFRP instruction (32-bit instructions) can use the 32-bit counter (high counter) but not the device
E.
Example
When X0.0 is ON, the instruction shifts the values of b0–b15 in D0 by 6 bits to the right, and transmits the value of b5 to
SM602. The instruction clears the values of b10–b15 to zero after the shift.
The shift of the values of the bits to the right during a scan is shown below.
 b5-b0 → Being carried (The value of b5 is transmitted to SM602.)
 b15-b6 → b9-b0
0 → b15-b10
6-340
b 15 ※ b0 Carry flag
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
After the shift
b 15 b0 Carry flag
0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0
Being fil led by 0
Additional remarks
If n is not between 0–16 (for 16-bit instructions) or between 0-32 (for 32-bit instructions), the instruction is not executed,
6_
6-341

Shifting the values of the bits in registers
1111 D SFL P D, n
by n bits to the left

D       
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  
n  

AS AS AS
Symbol
D ： Device for the shift
n ： Number of bits
Explanation
1. This instructions shift the values of the bits in D by n bits to the left. The instructions fill the vacancies (b0–bn-1)
resulting from the shift with 0 and transmit the value of b16-n (for 16-bit instruction) or b32-n (for 32-bit instruction) to
SM602.
_6
2. The operand n must be between 1–16 for 16-bit instructions and the operand n must be between 1–32 for 32-bit
instructions.
3. In general, the SFRP/DSFRP pulse instruction is used more commonly.
4. Only the DSFR/DSFRP instruction (32-bit instructions) can use the 32-bit counter (high counter) but not the device
E.
Example
When X0.0 is ON, the instruction shifts the values of b0–b15 in D0 by 6 bits to the right, and transmits the value of b10 to
SM602. The instruction fills the values of b0–b5 with zeros after the shift.
The shift of the values of the bits to the left during a scan shown below.
 b15-b10 → Being carried (The value of b10 is transmitted to SM602.
 b9-b0 → b15-b6
0 → b5-b0
6-342
b 15 ※ b0
Carry flag
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
After the s hift
Carry flag
b 15 b0
1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 1
Being fill ed by 0
Additional remarks
If n is not between 0–16 (for 16-bit instructions) or between 0-32 (for 32-bit instructions), the instruction is not executed,
6_
6-343

Shifting the states of n bit devices by one bit to the
1112 BSFR P D, n
right

D    
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D 
n  

AS AS -
Symbol
D ： First device for the shift
n ： Data length
Explanation
1. This instruction shifts the states of the n bit devices starting from D by one bit to the right. The instruction clears
_6 state of D+n-1 to 0, and transmits the state of D to the carry flag SM602.
2. In general, the BSFRP pulse instruction is used.
Example
When X0.0 is ON, the instruction shifts the states of M0–M5 by one bit to the right, clears the state of M5 to zero, and
transmits the state of M0 to the carry flag SM602.
6-344
M5 M4 M3 M2 M1 M0 Carry flag
0 0 0 1 0 1
After the shift
0 0 0 0 1 0 1
Being c leared to 0
Additional remarks
16#2003.
2. If n not between 1–1024, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
6_
6-345

Shifting the states of n bit devices by one
1113 BSFL P D, n
bit to the left

D    
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D 
n  

AS AS -
Symbol
n ： Data length
Explanation
1. This instruction shifts the states of the n bit devices starting from D by one bit to the left. The instruction clears the
_6 state of D to 0, and transmits the state of D+n-1 to the carry flag SM602.
2. In general, the BSFLP pulse instruction is used.
Example
When X0.0 is ON, the instruction shifts the states of M0–M5 by one bit to the left, clears the state of M0 to 0, and
transmits the state of M5 to the carry flag SM602.
6-346
0 0 0 1 0 1
After the s hift
0 0 1 0 1 0 0
Being c leared to 0
Additional remarks
16#2003.
6_
6-347
1114 D NSFR P D, n Shifting n registers to the right

D    
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n    

AS AS AS
Symbol
n ： Data length
_6 Explanation
1. This instruction shifts the data in the n registers starting from D to the right, and clears the data in D+n-1 to 0.
2. In general, the NSFRP pulse instruction is used.
Example 1
When M0 switches from OFF to ON, the instruction shifts the data in D1–D6 to the right, and clears the data in D6 to 0.
6-348
D6 D5 D4 D3 D2 D1 D0
30 2235 9578 754 28 423 11
After the shift
D6 D5 D4 D3 D2 D1 D0
0 30 2235 9578 754 28 423
Being cleared to 0
Example 2
When M0 is ON, When M0 switches from OFF to ON, the instruction shifts the 7 pieces of 32-bit data in D0–D13 one
place to the right, and clears the data in D12 to 0.
D12 D10 D8 D6 D4 D2 D0
90000 80000 70000 60000 50000 30000 40000
After the shift
D12 D10 D8 D6 D4 D2 D0
6_
0 90000 80000 70000 60000 50000 30000
Additional remarks
16#2003.
16#200B.
6-349
1115 D NSFL P D, n Shifting n registers to the left

D    
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    
n  

AS AS AS
Symbol
n ： Data length
_6 Explanation
1. This instruction shifts the data in the n registers starting from D to the left, and clears the data in D to 0.
2. In general, the NSFLP pulse instruction is used.
Example
When M0 switches from OFF to ON, the instruction shifts the data in D0–D5 to the left, and clears the data in D0 to 0.
6-350
D6 D5 D4 D3 D2 D1 D0
30 2235 9578 754 28 423 11
After the shift
D6 D5 D4 D3 D2 D1 D0
2235 9578 754 28 423 11 0
Being c leared to 0
Additional remarks
16#2003.
16#200B.
6_
6-351
6.13 Data Processing Instructions

6.13.1 List of Data Processing Instructions
The following table lists the Data Processing instructions covered in this section.

API Function
1200 SER DSER  Searching the data
1201 SUM DSUM  Finding the number of bits whose states are ON
1202 DECO –  Decoding bits
1203 ENCO –  Encoding bits
1204 SEGD –  Seven-segment decoding
1205 SORT DSORT  Sorting data
1206 ZRST –  Resetting a zone
1207 BON DBON  Checking the state of a bit
1208 MEAN DMEAN  Finding the mean
1209 CCD –  Finding the sum check
1210 ABS DABS  Finding the absolute value
1211 MINV –  Inverting matrix bits

_6
1212 MBRD –  Reading a matrix bit
1213 MBWR –  Writing a matrix bit
1214 MBC –  Counting the bits with the value zero or one
1215 DIS –  Disuniting 16-bit data
1216 UNI –  Uniting 16-bit data
1217 WSUM DWSUM  Finding the sum
1224 – FMEAN  Finding the mean of floating point numbers
1225 – FSUM  Finding the sum of floating point numbers
1226 – DTM  Data conversion and move
1227 – ZSET  Zone setup
6-352
6.13.2 Explanation of Data Processing Instructions
1200 D SER P S1, S2, D, n Searching the data

S1       
S2           
D     
n           
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
D    
n    

AS AS AS
Symbol
S1 ： First device for the comparison
S2 ： Compared data
6_
D ： First device where the comparison result is stored
n ： Data length
Explanation
1. This instruction compares n signed decimal values in the registers starting from the register specified by S1 with
the signed decimal value in the register specified by S2, and stores the comparison results in the registers D–D+4.
6-353
Device Description
D Number of equal values
Data number of the first equal

D+1
value
Data number of the last equal

D+2
value
Data number of the minimum

D+3
value
Data number of the maximum

D+4
value
Example
1. When X0.0 is ON, the instruction compares the values in D10–D19 with the value in D0, and stores the
comparison results in D50–D54. When the equal value does not exist in D10–D19, the values in D50–D52 are 0.
2. The instruction stores the data number of the minimum value in D53, and stores the data number of the maximum
value in D54. If there is more than one minimum value or maximum value, the instruction stores the data number
_6 that is bigger.
6-354
Compared Data
S1 Value Result D Value Description
data number
D10 88 0 D50 4 Number of equal values
Data number of the first

D11 100 1 Equal D51 1
equal value
Data number of the last

D12 110 2 D52 8
equal value
Data number of the

D13 150 3 D53 7
minimum value
n S2
D0=100 Data number of the

D14 100 4 Equal D54 9
maximum value
D15 300 5
D16 100 6 Equal
D17 5 7 Minimum
D18 100 8 Equal
D19 500 9 Maximum
6_
Additional remarks
1. If S1+n-1 or D+4 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
2. For 16-bit instructions, if the value in n is not between 1–256, the instruction is not executed, SM0 is ON, and the
3. For 32-bit instructions, if the value in n is not between 1–128, the instruction is not executed, SM0 is ON, and the
4. For 16-bit instructions, if you declare the operand D in ISPSoft, the data type is ARRAY [5] of WORD/INT.
5. For 32-bit instructions, if you declare the operand D in ISPSoft, the data type is ARRAY [5] of DWORD/DINT.
6-355

Finding the number of bits whose states
1201 D SUM P S, D
are ON

S           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    

AS AS AS
Symbol
S ： Source device
Explanation
_6 1. This instruction finds the number of bits in S whose values are ON and stores the number of ON bits in D.
2. When the values of all the bits in the source device specified by S are 0, the zero flag SM600 is ON.
Example
When X0.0 is ON, the instruction stores the number of bits whose values are one in D0 in D2.
b15 b0
0 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0 3
D0 D2
Additional remarks
If the device exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6-356
1202 DECO P S, D, n Decoding bits

S           
D       
n   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D   
n  

AS AS -
Symbol
S ： Source device
D ： Device where the decoded values are stored
n ： Number of bits whose values are decoded

6_
Explanation
1. This instruction decodes the values of the lower n bits in the source device specified by S as the values of the
lower 2n bits in D.
2. The instruction decodes the values of the consecutive n bits in the source device specified by S as the values of
the lower 2n bits in D.
3. When the source device specified by S is a timer or counter, the instruction treats the device as a word device.
4. When D is a bit device, n between1–8. When n is 8, the instruction decodes the values of the eight bits as the
values of the 256 bits. Please note that the devices in which the decoded values are stored cannot be used
repeatedly.
5. When D is a word device, n between 1–4. When n is 4, the instruction decodes the values of the four bits as the
values of the 16 bits.
6. In general, the DECOP pulse instruction is used.
6-357
Example 1
1. When Y0.0 switches from OFF to ON, the DECO instruction decodes the values of the 3 bits in X0.0–X0.2 as the
values of the 8 bits in M100–M107.
2. The instruction adds the values of the 3 bits in X0.0–X0.2 to get the value 3. The instruction sets the third bit in
M10–M1007, that is, the bit in M103 to 1.
3. After the DECO instruction is executed and Y0.0 switches to OFF, the values of the eight bits in M100–M107 are
unchanged.
X0.2 X0.1
0 1 1
4 2 1
_6 3
7 6 5 4 3 2 1 0
0 0 0 0 1 0 0 0
M107 M106 M105 M104 M103 M102 M101 M100
Example 2
1. When X0.0 switches from OFF to ON, the DECO instruction decodes the values of b2–b0 in D10 as the values of
b7–b0 in D20, and sets the values of b15–b8 in D10 to 0.
2. The instruction decodes the values of the lower three bits in D10 as the values of the lower eight bits in D20. The
instruction sets the values of the higher eight bits to 0.
3. After the DECO instruction is executed and X0.0 switches to OFF, the data in D20 is unchanged.
6-358
b15 D10 b0
0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1
4 2 1
T he values of b15~b8
in D10 bec ome 0.
7 6 5 4 3 2 1 0
0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
b15 D20 b0
Additional remarks
1. If D is a bit device and if n not between 1–8, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#200B.
2. If D is a word device and if n is not between 1–4, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
3. If S is a bit device and if S+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error
4. If D is a bit device and if D+(2^n)-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
6_
6-359
1203 ENCO P S, D, n Encoding bits

S           
D      
n          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S   
D  
n  

AS AS -
Symbol
S ： Source device
D ： Device where the encoded values are stored
n ： Number of bits whose values are encoded
_6 Explanation
1. When S is a word device, this instruction encodes the values of the lower 2n bits in the source device specified by
S as the values of the lower n bits in D.
2. When S is a bit device, the instruction processes the higher bit with the value S+(n-1) from the lower 2n bits and
3. When the source device specified by S is a timer or counter, the instruction treats the device as a word device.
4. When S is a bit device, n is between 1–8. When n is 8, the instruction encodes the values of the 256 bits as the
values of the eight bits.
5. When S is a word device, n is between 1–4. When n is 4, the instruction encodes the values of the 16 bits as the
values of the four bits.
6. In general, the ENCOP pulse instruction is used.
Example 1
1. When X0.0 switches from OFF to ON, the ENCO instruction encodes the values of the 8 bits in M0–M7 as the
6-360
values of the lower 3 bits in D0, and sets the values of b15–b3 in D0 to 0.
2. After the ENCO instruction is executed and X0.0 switches to OFF, the data in D is unchanged.
M7 M6 M5 M4 M3 M2 M1 M0
0 0 0 0 1 0 0 0
7 6 5 4 3 2 1 0
b15 D0 4 2 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
b0
T he values of b15~b3 in D0 become 0.
Example 2
1. When X0.0 switches from OFF to ON, the ENCO instruction encodes the values of b0–b7 in D10 as the values of
b2–b0 in D20, and sets the values of b15–b3 in D20 to zero. The values of b8–b18 in D10 are invalid data.
6_
2. After the ENCO instruction is executed and X0.0 switches OFF, the data in D is unchanged.
b15 D10 b0
0 1 0 1 0 1 0 1 0 0 0 0 1 0 0 0
7 6 5 4 3 2 1 0
T he values of b8~b18 in D10 are invalid data.
b15 D20
0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
b0
T he values of b15~b3 in D20 become 0.
Additional remarks
1. If there is no bit whose value is one in the source device specified by S, the instruction is not executed, SM0 is ON,
6-361
2. If S is a bit device and if n is not between 1–8, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
3. If S is a word device and if n is not between 1–4, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
4. If S is a bit device and if S+(2^n)-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
5. If D is a bit device and if D+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error
_6
6-362
1204 SEGD P S, D Seven-segment decoding

S          
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D  

AS AS -
Symbol
S ： Source device
D ： Device where the seven-segment data is stored
Explanation
6_
The instruction decodes the values of the lower four bits (b0–b3) in the source device specified by S as the seven-
segment data stored in D.
Example
When X0.0 is ON, the instruction decodes the values of b0–b3 in D0 as the seven-segment data stored in Y0.0–Y0.15. If
the data in the source device exceeds four bits, the instruction decodes the values of the lower four bits.
6-363
The following table shows the relation between the seven-segment data and the bit pattern of source data.
Segment s tate
Bi t Assi gnment
Hex Dis play
pattern of s egments B0(a) B1(b) B2(c) B3(d) B4(e) B5(f) B6(g)
0 0000 ON ON ON ON ON ON OFF
1 0001 OFF ON ON OFF OFF OFF OFF

2 0010 ON ON OFF ON ON OFF ON
3 0011 ON ON ON ON OFF OFF ON
4 0100 OFF ON ON OFF OFF ON ON
5 0101 ON OFF ON ON OFF ON ON
6 0110 a ON OFF ON ON ON ON ON
7 0111 f g b ON ON ON OFF OFF ON OFF
8 1000 e c ON ON ON ON ON ON ON
d
9 1001 ON ON ON ON OFF ON ON
A 1010 ON ON ON OFF ON ON ON
B 1011 OFF OFF ON ON ON ON ON
C 1100 ON OFF OFF ON ON ON OFF
D 1101 OFF ON ON ON ON OFF ON
E 1110 ON OFF OFF ON ON ON ON
F 1111 ON OFF OFF OFF ON ON ON
_6
6-364
1205 D SORT P S, m1, m2, D, n Sorting data

S 
m1   
m2   
D 
n   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
m1    
m2    
D    
n    

AS AS AS
Symbol
S ： First device where the original data is stored
m1 ： Number of rows of data
m2 ： Number of columns of data 6_

D ： First device where the sorted data is stored
n ： Reference value for sorting the data
Explanation
1. This instruction stores the data to be sorted in the m1×m2 registers starting from the register specified by D. If S
and D specify the same register, the sorted data is the same as the original data in the register specified by S.
2. The operand m1 must be between 1–32. The operand m2 must be between 1–6. The operand n must be between
1–m2.
3. When SM604 is OFF, the instruction sorts the data in ascending order. When SM604 is ON, the instruction sorts
the data in descending order.
4. It is suggested that you use the SORTP or DSORTP pulse type instruction instead of sorting repeatedly.
6-365
Example
1. Suppose SM604 is OFF. When X0.0 switches from OFF to ON, the instruction sorts the data in ascending order.
2. The data which to be sorted is as in the following table.
m2 columns of data
Column
Column 1 2 3 4 5
Student
Chinese English Math Physics
Row number
1 (D0) 1 (D5) 90 (D10) 75 (D15) 66 (D20) 79
_6 2 (D1) 2 (D6) 55 (D11) 65 (D16) 54 (D21) 63

m1 rows of data
3 (D2) 3 (D7) 80 (D12) 98 (D17) 89 (D22) 90
4 (D3) 4 (D8) 70 (D13) 60 (D18) 99 (D23) 50
5 (D4) 5 (D9) 95 (D14) 79 (D19) 75 (D24) 69
6-366
3. When the value in D100 is 3, the data is sorted as in the following table.
m2 columns of data
Column
Column 1 2 3 4 5
Student
Row number
1 (D50) 4 (D55) 70 (D60) 60 (D65) 99 (D70) 50
2 (D51) 2 (D56) 55 (D61) 65 (D66) 54 (D71) 63

m1 rows of data
3 (D52) 1 (D57) 90 (D62) 75 (D67) 66 (D72) 79
4 (D53) 5 (D58) 95 (D63) 79 (D68) 75 (D73) 69
5 (D54) 3 (D59) 80 (D64) 98 (D69) 89 (D74) 90
4. When the value in D100 is 5, the data is as in the following table.
6_
m2 columns of data
Column
Column 1 2 3 4 5
Student
Row number
1 (D50) 4 (D55) 70 (D60) 60 (D65) 99 (D70) 50
2 (D51) 2 (D56) 55 (D61) 65 (D66) 54 (D71) 63

m1 rows of data
3 (D52) 5 (D57) 95 (D62) 79 (D67) 75 (D72) 69
4 (D53) 1 (D58) 90 (D63) 75 (D68) 66 (D73) 79
5 (D54) 3 (D59) 80 (D64) 98 (D69) 89 (D74) 90
6-367
Additional remarks
2. If m1, m2, or n exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
_6
6-368
1206 ZRST P D1, D2 Resetting a zone

D1          
D2          
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D1   
D2   

AS AS -
Symbol
D1 ： First device to be reset
D2 ： Last device to be reset
Explanation
1. This instruction clears the values in D1–D2. The device type for D1–D2 should be the same for this instruction.
2. When the device number of D1 is larger than the device number of D2, the instruction resets only D2. 6_
3. The ZRST instruction can use the 32-bit counter.
Example
1. When X0.0 is ON, the instruction resets the auxiliary relays M300–M399 to OFF.
2. When X1.0 is ON, the instruction resets the 16-bit counters C0–C127. The values of C0–C127 are cleared to zero,
and the contact and the coil are reset to OFF.
3. When X2.0 is ON, the instruction resets the stepping relays S0–S127 to OFF.
4. When X3.0 is ON, the instruction resets the output relays Y0.0–Y1.15 to OFF.
5. When X4.0 is ON, the instruction resets the 32-bit counters HC0–HC63. The values of HC0–HC63 are cleared to
zero, and the contact and the coil are reset to OFF.
6. When X5.0 is ON, the instruction resets the timers T0–T127. The values of T0–T127 are cleared to 0. and the
contact and the coil are reset to OFF.
6-369
_6
Additional remarks
1. If D1 and D2 are different types of devices, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2007.
2. If D1 and D2 contain different data formats, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2007.
6-370
1207 D BON P S, D, n Checking the state of a bit

S           
D     
n   DWORD         
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D 
n    

AS AS AS
Symbol
S ： Source device
D ： Device where the check result is stored
n ： Bit whose state is checked
6_
Explanation
1. This instruction checks the state of the nth bit in S, and stores the result in D.
2. The operand n used in the 16-bit instruction must be between 0–15. For 32-bit instructions, n must be between 0–
31.
Example
1. When X0.0 is ON, Y0.1 is ON if the value of the 15th bit in D0 is one. When X0.0 is ON, Y0.1 is OFF if the value of
the 15th bit in D0 is 0.
2. When X0.0 switches to OFF, the state of Y0.1 remains the same as before X0.0 switches to OFF.
6-371
b15 b0
0 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0 Y0.1=OFF
D0
b15 b0
1 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0 Y0.1=ON
D0
Additional remarks
If n exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
_6
6-372
1208 D MEAN P S, D, n Finding the mean

S       
D       
n   DWORD         
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D    
n    

AS AS AS
Symbol
S ： First device
D ： Device where the mean is stored
6_
Explanation
1. This instruction adds up the values in the n devices starting from the device specified by S, and the stores the
mean of the sum in D.
2. If a remainder appears in the calculation, the instruction discards it.
3. For 16-bit instructions, n must be between 1–256.
4. For 32-bit instructions, n must be between 1–128.
Example
When X0.0 is ON, the instruction adds up the values in the three registers starting from D0. The instruction divides the
sum by 3. The instruction stores the quotient in D10, and leaves out the remainder.
6-373
(D0+D1+D2)/3 D10
D0 100

D1 113 D10 112
is executed
D2 125 T he quotient 2 is left out.
Additional remarks
1. For 16-bit instructions, if n not between 1–256, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
2. For 32-bit instruction, if n is not between1–128, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
16#2003.
_6
6-374
1209 CCD P S, D, n Finding the sum check

S      
D    
n   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D  
n  

AS AS -
Symbol
S ： First device
D ： Device where the sum is stored
n ： Number of pieces of data
Explanation 6_
1. Communication protocols use the sum check function to compare checksums on the same data on different
occasions or on different representations of the data to verify data integrity.
2. When SM606 is OFF, the instruction uses the 16-bit conversion mode. The instruction adds up n pieces of data in
the registers starting from the register specified by S (eight bits as a group). The instruction stores the sum in the
register specified by D, and stores the values of the parity bits in D+1.
3. When SM606 is ON, the instruction uses the 8-bit conversion mode. The instruction adds up the n pieces of data in
the registers starting from the register specified by S (eight bits in a group, and only low eight bits are valid). The
instruction stores the sum in the register specified by D, and stores the values of the parity bits in D+1.
6-375
Example 1
1. When SM606 is OFF, the instruction uses the 16-bit conversion mode.
2. When X0.0 is ON, the instruction adds up the six pieces of data in D0–D2 (eight bits in a group). The instruction
stores the sum in D100, and stores the values of the parity bits in D101.
S Data
D0 Low 100 = 0 1 1 0 0 1 0 0
D0 High 111 = 0 1 1 0 1 1 1 1
D1 Low 120 = 0 1 1 1 1 0 0 0
D1 High 202 = 1 1 0 0 1 0 1 0
D2 Low 123 = 0 1 1 1 1 0 1 1
D2 High 211 = 1 1 0 1 0 0 1 1
D100 867 Sum
D101 00 01 000 1
_6 T he parity bit is set to 1 if the number of ones i s odd.
T he parity bit is set to 0 if the number of ones i s even.
D100 0 0 0 0 0 0 1 1 0 1 1 0 0 0 1 1
D101 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 Pari ty bits
Example 2
1. When SM606 is ON, the instruction uses the 8-bit conversion mode.
2. When X0.0 is ON, the instruction adds up the six pieces of data in D0–D5 (eight bits in a group). The instruction
stores the sum in D100, and stores the values of the parity bits in D101.
6-376
S Data
D0 Low 100 = 0 1 1 0 0 1 0 0
D1 Low 111 = 0 1 1 0 1 1 1 1
D2 Low 120 = 0 1 1 1 1 0 0 0
D3 Low 202 = 1 1 0 0 1 0 1 0
D4 Low 123 = 0 1 1 1 1 0 1 1
D5 Low 211 = 1 1 0 1 0 0 1 1
D100 867 Sum
D101 00 01 000 1
T he parity bit is set to 1 if the number of ones is odd.
T he parity bit is set to 0 if the number of ones is even.
D100 0 0 0 0 0 0 1 1 0 1 1 0 0 0 1 1
D101 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 Pari ty bits
6_
Additional remarks
1. Suppose SM606 is ON. If S+n-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
2. Suppose SM606 is OFF. If S+n/2-1 exceeds the device range, the instruction is not executed, SM0 is ON, and the
6-377
1210 D ABS P D Finding the absolute value

D  DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D    

AS AS AS
Symbol
D ： Device holding the original value
Explanation
1. This instruction finds the absolute value of the value in the device specified by D.
_6 2. In general, the ABSP pulse instruction is used.
4. If the value used here is a smallest negative number for the 16-bit number or 32-bit number, this instruction is not
executed.
Example
Supposedly the value in D0 is originally -1234. When X0.0 switches from OFF to ON, the instruction finds the absolute
value of -1234 in D0. That is, the value in D0 becomes 1234 after the instruction is executed.
6-378
1211 MINV P S, D, n Inverting matrix bits

S      
D    
n   DWORD       
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D  
n  

AS AS -
Symbol
S ： Matrix source
Explanation
1. This instruction inverts the bits in the n devices starting from the device specified by S, and stores the inversion 6_
result in D.
Example
When X0.0 is ON, the instruction inverts the bits in the three 16-bit registers D0–D2, and stores the inversion result in the
16-bit registers D20–D22.
6-379
b15 b0
D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
After the i nstruction is executed

b15 b0
D20 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
D21 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
D22 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
Additional remarks
1. If S+n-1 or D+n-1 exceeds the device range, the instruction is not execute, SM0 is ON, and the error code in SR0
is 16#2003.
_6
6-380
1212 MBRD P S, n, D Reading a matrix bit

S      
n         
D  DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS -
Symbol
S ： Matrix source
D ： Pointer
Explanation 6_
1. This instruction checks the state of SM613. If SM613 is ON, the instruction clears the value of the pointer D to
zero. The instruction reads the value of the bit specified by the value of the pointer D into SM614, and then checks
the state of SM612. If SM612 is ON, the instruction increments the value of the pointer D by adding one.
2. When the instruction reads the value of the last bit, SM608 is ON, and the instruction stores the bit number in the
pointer D.
4. You specify the value of the pointer. The values are between 0–16n−1, and correspond to the range between b0–
b16n−1. If the value of the pointer exceeds the range, SM611 is set to one, and the instruction is not executed.
Example
1. Suppose SM613 is OFF and SM612 is ON when X0.0 switches from OFF to ON.
2. Suppose the current value in D20 is 45. When X0.0 is switched from OFF to ON three times, the instruction gives
the following execution results.
6-381
 The value in D20 is 46, SM614 is OFF, and SM608 is OFF.
 The value in D20 is 47, SM614 is ON, and SM608 is OFF.
 The value in D20 is 47, SM614 is OFF, and SM608 is ON.
b15 b0
D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
45 Pr
D20
Additional remarks
_6 16#2003.
SM608: The matrix comparison comes to an end. When the last bits are compared, SM608 is
ON.
SM611: Matrix pointer error flag. When the value of the pointer exceeds the comparison range,
SM611 is ON.
SM612: Matrix pointer increasing flag. The current value of the pointer increases by one.
SM613: Matrix pointer clearing flag. The current value of the pointer is cleared to zero.
SM614: Carry flag for the matrix rotation/shift/output.
6-382
1213 MBWR P S, n, D Writing a matrix bit

S    
n         
D  DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS -
Symbol
S ： Matrix source
D ： Pointer
Explanation
1. This instruction checks the state of SM613. If SM613 is ON, the instruction clears the value of the pointer D to 0. 6_
The instruction writes the state of SM615 into the bit specified by the value of the pointer D and then checks the
state of SM612. If SM612 is ON, the instruction increments the value in the pointer D by one.
2. When the instruction writes the state of SM615 into the last bit, sets SM608 is ON, and records the bit number in
the pointer D. If value of the pointer D exceeds the range, SM611 is ON.
4. You specify the value of the pointer. The values are between 0–16n−1, and correspond to the range between b0–
b16n−1. If the value of the pointer exceeds the range, SM611 is set to one, and the instruction is not executed.
Example
1. Suppose SM613 is OFF and SM612 is ON when X0.0 switches from OFF to ON.
2. Suppose the current value in D20 is 45. When X0.0 switches from OFF to ON one time, the instruction gives the
execution result shown below. When the value in D20 is 45, SM615 is OFF, and SM608 is OFF.
6-383
b1 5 b0
D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 SM 6 15
D1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
45 Pr
P
Afte r the i nstru cti on is e xecute d D 20
b 15 b0
D0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 SM 6 15
D1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
D2 0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1
46 Pr
D20
Additional remarks
16#2003.
_6
SM608: The matrix comparison comes to an end. When the last bits are compared, SM608 is ON.
SM611: Matrix pointer error flag. When the value of the pointer exceeds the comparison range, SM611 is ON.
SM612: Matrix pointer increasing flag. The current value of the pointer increases by one.
SM613: Matrix pointer clearing flag. The current value of the pointer is cleared to zero.
SM615: Borrow flag for the matrix shift/output.
6-384

Counting the bits with the value zero or
1214 MBC P S, n, D
one

S    
n         
D  DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS -
Symbol
S ： Matrix source
Explanation
1. This instruction counts the bits with the value one or zero in the n devices starting from the device specified by S. 6_
The instruction stores the operation result in D.
2. When SM617 is ON, the instruction counts the bits with the value one. When SM617 is OFF, the instruction counts
the bits with the value 0. When the operation result is 0, SM618 is ON.
Example
Suppose SM617 is ON. When X0.0 is ON, the instruction counts the bits with the value one, and stores the operation
result in D20. Suppose SM617 is OFF. When X0.0 is ON, the instruction counts the bits with the value zero, and stores
the operation result in D20.
6-385
b15 b0
D0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 0 12
D1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 SM 617 D20
D2 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1
1 36
SM 617 D20
Additional remarks
16#2003.
SM617: The bits with the value zero or one are counted.
SM618: ON when the matrix counting result is 0.
_6
6-386
1215 DIS P S, n, D Disuniting 16-bit data

S        
n          
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS -
Symbol
S ： Data source
6_
Explanation
1. This instruction divides the 16-bit value in the register specified by S into four groups (four bits in a group), and
stores these groups in the low four bits in every register (the registers range from D to D+(n-1)).
b15 b12 b11 b8 b7 b4 b3 b0 b15 b4 b3 b0
S D
D +1 n
D +2
D +3
All becomes 0. T he positions i n whcih

the data is stored.
Example
Suppose the value in D0 is 16#1234. When M0 is enabled, the instruction divides the value in D0 into four groups (four
bits in a group), and stores these groups in the low four bits in every register (the registers range from D10 to D13.).
6-387
b15 b12 b11 b8 b7 b4 b3 b0 b15 b4 b3 b0

D0 1 2 3 4 4 D1 0
3 D11
4
2 D1 2
1 D1 3
All becomes 0. T he positions in whcih

the data is stored.
Additional remarks
1. If D–D+(n-1) exceed the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
_6 2. If n is not between 1–4, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
6-388
1216 UNI P S, n, D Uniting 16-bit data

S      
n          
D  DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

AS AS -
Symbol
S ： Data source
n ： Data length
6_
Explanation
1. This instruction divides the 16-bit values in the registers specified by S–S+(n-1) into groups (four bits in a group),
and stores every group that is in b0–b3 in the register specified by D (b0–b15).
b15 b4 b3 b0
S
S +1
S +2
S +3 D
b15 b12 b11 b8 b7 b4 b3 b0
Being i gnor ed T he data whic h

is stored
Example
Suppose the values in D0–D3 are 16#1234, 16#5678, 16#8765, and 16#4321 respectively. When M0 is enabled, the UNI
instruction divides the values in D0–D3 into groups (four bits in a group), and stores every group in b0–b3 in D10(b0–
b15).
6-389
b15 b4 b3 b0
D0 1 2 3 4
D1 5 6 7 8
D2 8 7 6 5
D3 4 3 2 1 1 5 8 4 D1 0
b15 b12 b11 b8 b7 b4 b3 b0
Additional remarks
1. If S to S+(n-1) exceed the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
_6
6-390
1217 D WSUM P S, n, D Getting the sum

S       
n           
D  DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
n    
D    

AS AS AS
Symbol
S ： Data source
n ： Data length
6_
Explanation
1. The instruction adds up the signed decimal values in S to S+n-1, and stores the sum in the register specified by D.
S
S +1
D +1 D
S +2
B in ar y val ue s n
S +3
S +4 B in ar y val ue
S +5
S S +1
S +3 S +2
D +1 D
S +5 S +4
B in ar y val ue s n D +3 D +2
S +7 S +6
B in ar y val ue
S +9 S +8
6-391
2. For 16-bit instructions, the value in n must be between 1–256.
3. For 32-bit instructions, the value in n must be between 1–128.
Example
The WSUM instruction adds up the values in D0–D2, and stores the sum (32-bit) in D10.
(D0+D1+D2) D10
D0 100

D1 113 D10 338
is executed
D2 125
_6
Additional remarks
1. For 16-bit instructions, the value in n is not between 1–256, the instruction is not executed, SM0 is ON, and the
2. For 32-bit instructions, the value in n is not between 1–128, the instruction is not executed, SM0 is ON, and the
3. If S+n-1 or D exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
4. For 16-bit instructions, ff you declare the operand D in ISPSoft, the data type is DWORD or ARRAY [2] of WORD.
5. For 32-bit instructions, if you declare the operand D in ISPSoft, the data type is ARRAY [2] of DWORD.
6-392
1221 D LIMIT P S1, S2, S3, D Confining a value within bounds

S1           
S2           
S3           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
S3    
D    

AS AS AS
Symbol
S1 ： Minimum output value
S2 ： Maximum output value
S3 ： Input value
D ： Output value 6_
Explanation
1. The instruction compares the input value in S3 with the minimum output value in S1 and the maximum output value
in S2, and stores the comparison result in D.
If the input value in S3 is smaller than the minimum output value in S1, the instructions stores minimum
output value S1 in D.
If the input value in S3 is larger than the maximum output value in S2, the instruction stores the
maximum output value S2 in D.
If the input value in S3 is between the minimum output value S1 and the maximum output value S2, the
instruction stores the input value S3 in D.
6-393
If the minimum output value in S1 is larger than the maximum output value in S2, the instruction is not
executed.
Example
 When X0.0 is ON, the instruction converts the state of X1 into a binary value, and stores the conversion result in
D0. Then the instruction compares the value in D0 with 500 and 5000, and stores the comparison result in D1.
Minimum output Maximum output

Output value in D0 Function Output value in D1
value value
_6 499 D0<500 500
500 5000 5001 D0>5000 5000
600 500≦D0≦5000 600
Additional remarks
If the minimum output value in S1 is larger than the maximum output value in S2, the instruction is not executed, SM0 is
6-394
1222 D BAND P S1, S2, S3, D Deadband control

S1           
S2           
S3           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
S3    
D    

AS AS AS
Symbol
S1 ： Minimum value of the deadband
S2 ： Maximum value of the deadband
S3 ： Input value
Explanation
1. This instruction subtracts the minimum value of the deadband in S1 or the maximum value of the deadband in S2
from the input value in S3, and stores the difference in D.
If the input value in S3 is smaller than the minimum value of the deadband in S1, the instruction subtracts S1 from
S3, and stores the difference in D.
If the input value in S3 is greater than the maximum value of the deadband in S2, the instruction subtracts S2 from
S3, and stores the difference in D.
If the input value in S3 is between the minimum of the deadband in S1 and the maximum value of the deadband in
S2, the instruction stores zero in D.
6-395
If the minimum value of the deadband in S1 is larger than the maximum value of the deadband in S2, the
instruction is not executed.
3. The following graphs show how this instruction uses the deadband.
BAND is not exec uted. BAND is exec uted.
Output value Output value
T he lower l imit value

of the deadband
Input value Input value
T he upper li mit value

of the deadband
4. The minimum value of the deadband in S1, the maximum value of the deadband in S2, the input value in S3, and
the output value in D must be within the range described below.
5. For the BAND instruction, the minimum value of the deadband in S1, the maximum value of the deadband in S2,
the input value in S3, and the output value in D must be between -32768 to 32767. Suppose the minimum value of
_6 the deadband in S1 is 10 and the maximum value of the deadband in S3 is -32768. The instruction calculates the
output value in D as follows.
Output value in D = -32768-10=16#8000-16#000A=16#7FF6=32758
6. For the DBAND instruction, the minimum value of the deadband in S1, the maximum value of the deadband in S2,
the input value in S3, and the output value in D must be between -2147483648 to 2147483647. Suppose the
minimum value of the deadband in (S1+1, S1) is 1000 and the maximum value of the deadband in (S3+1, S3) is -
2147483648. The instruction calculates the output value in (D+1, D) as follows.
Output value in (D+1, D)
=-2147483648-1000=16#80000000-16#000003E8=16#7FFFFC18
=2147482648
6-396
Example 1
When X0.0 is ON, the instruction subtracts -1000 or 1000 from the binary-coded decimal value in X1, and stores the
difference in D1.
The following table shows the execution results.
Minimum value Maximum

Input value in
of the value of the Function Output value in D1
D0
deadband deadband
-1200 D0<-1000=>D1=D0-（-1000） -200
-1000 1000 1200 D0>1000=>D1=D0-1000 200
500 -1000≦D0≦1000=>D0=0 0
6_
Example 2
When X0.0 is ON, the instruction subtracts -10000 or 10000 from the binary-coded decimal value in (X2, X1), and stores
the difference in (D11, D10).
6-397
Minimum value Maximum

Input value in Output value in
of the value of the Function
(D1, D0) (D11, D10)
deadband deadband
（D1，D0）<-10000
-12000 =>（D11，D10） -2000
=（D1，D0）-（-10000）
（D1，D0）>10000
-10000 10000
12000 =>（D11，D10） 2000
=（D1，D0）-10000
-10000≦（D1，D0）≦10000
5000 0
=>（D1，D0）=0
Additional remarks
If the minimum value of the deadband in S1 is larger than the maximum value of the deadband in S2, the instruction is not
_6
6-398
1223 D ZONE P S1, S2, S3, D Controlling the zone

S1           
S2           
S3           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1    
S2    
S3    
D    

AS AS AS
Symbol
S1 ： Negative deviation
S2 ： Positive deviation
S3 ： Input value
Explanation
1. This instruction adds the negative deviation in S1 or the positive deviation in S2 to the input value in S3, and stores
the sum in D.
If the input value in S3 is less than 0, the instruction adds the negative deviation in S1 to the input value in S3, and
stores the sum in D.
If the input value in S3 is larger than 0, the instruction adds the positive deviation in S2 to the input value in S3, and
stores the sum in D.
If the input value in S3 is equal to zero, the instruction stores zero in D.
6-399
2. The following graphs show how this instruction uses the zone:
Z ONE is not ex ec uted. Z ONE is exec uted.
Output value Output value
Positiv e deviation
Input value Input value
Negativ e deviation
3. Only the 32-bit instructions can use the 32-bit counter but not the device E.
4. The negative deviation in S1, the positive deviation in S2, the input value in S3, and the output value in D must be
within the range described below.
 For the ZONE instruction, the negative deviation in S1, the positive deviation in S2, the input value in S3, and
the output value in D must be between -32768 to 32767. Suppose the negative deviation in S1 is -100 and
the input value in S3 is -32768. The instruction calculates the output value in D as follows.
Output value in D=(-32768)+(-100)=16#8000+16#FF9C=16#7F9C=32668

_6
For the DZONE instruction, the negative deviation in S1, the positive deviation in S2, the input value in S3,
and the output value in D must be between -2147483648 to 2147483647. Suppose the negative deviation in
(S1+1, S1) is -1000 and the input value in (S3+1, S3) is -2147483648. The instruction calculates the output
value in (D+1, D) as follows.
Output value in (D+1, D)
=-2147483648+(-1000)=16#80000000+16#FFFFFC18=16#7FFFFC18=2147482648
Example 1
When X0.0 is ON, the instruction adds -100 or 100 to the binary-coded decimal value in X1, and stores the sum in D10.
6-400
Negative Positive Input value in Output value in D10

Function
deviation deviation D0
-10 D0<0=>D10=（-10）+（-100） -110
-100 100 0 D0=0=>D10=0 0
50 D0>0=>D10=50+100 150
Example 2
When X0.0 is ON, the instruction adds -10000 or 10000 to the binary-coded decimal value in (X2, X1), and stores the
sum in (D11, D10).
6_

Negative Positive Input value in (D1, Output value in (D11,
Function
deviation deviation D0) D10)
（D1，D0）<0
-10 =>（D11，D10） -10010
=（-10）+（-10000）
-10000 10000 （D1，D0）=0
0 0
=>（D11，D10）=0
（D1，D0）>0
50 10050
=>（D11，D10）=50+10000
6-401
1224 FMEAN P S, D, n Finding the mean of floating point numbers

S  
n    
D   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
n  
D 

AS - AS
Symbol
S ： First device
D ： Device where the mean is stored
_6
Explanation
1. This instruction adds up the single precision floating points in the n devices starting from the device specified by S,
divides the sum by the value in n, then stores the mean of the sum in D.
2. For 16-bit instructions, the value in n must be between 1–256,
3. Instruction flags: SM600 (zero flag), SM601 (borrow flag), SM602 (carry flag):
 If the value while adding or the absolute result of the operation is less than the floating point number that can
be shown, the D=16#FF800000 and the borrow flag SM601 is ON.
 If the value while adding or the absolute result of the operation is larger than the floating point number that can
be shown, the D=16#7F800000 and the carry flag SM602 is ON.
Example
When X0.0 is ON, the instruction adds the values of the 3 single precision floating points in (D1, D0), (D3, D2), (D5, D4)
and then divides the addition result by 3, then stores the result in (D11, D10).
6-402
[(D1, D0) +( D3, D 2)+(D5, D4 )]/3 ( D11, D 10)
(D1, D 0) 10 0.1 Aft er the inst ruc ti on is execu ted.
( D11, D1 0) 11 2.2
(D3, D 2) 113.2
(D5, D 4) 123.3
Additional remarks
16#200B.
2. If S+2*n-1exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in S exceeds the range of floating point numbers that can be shown, the instruction is not executed,
6_
6-403
1225 FSUM P S, n, D Finding the sum of floating point numbers

S  
n    
D   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
n  
D 

AS - AS
Symbol
S ： Data source
n ： Data length
_6
Explanation
1. This instruction adds up the single precision floating points in the n devices starting from the device specified by S,
then stores the sum in D.
2. For 16-bit instructions, the value in n must be between 1–256,
3. Instruction flags: SM600 (zero flag), SM601 (borrow flag), SM602 (carry flag):
 If the value while adding or the absolute result of the operation is less than the floating point number that can
be shown, the D=16#FF800000 and the borrow flag SM601 is ON.
 If the value while adding or the absolute result of the operation is larger than the floating point number that can
be shown, the D=16#7F800000 and the carry flag SM602 is ON.
6-404
S +1 S
S +3 S +2
S +5 S +4 D +1 D
F lo at ing p oi nt nu mb ers n=5
S +7 S +6
F l oatin g po int n umbers
S +9 S +8
Example
The FSUM instruction adds up the values of the 3 single precision floating points in (D1, D0), (D3, D2), (D5, D4) and
stores the result in (D11, D10).
[( D1, D 0)+( D3, D 2)+(D5 , D4)] ( D11, D10 )
(D1, D0) 10 0.1

Aft er t he inst ruc tio n is execu ted.
(D3, D2) 113.2 (D11, D10) 33 8.6
(D5, D4) 125.3 6_
Additional remarks
16#200B.
2. If S+2*n-1exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in S exceeds the range of the floating point numbers that can be shown, the instruction is not executed,
6-405
1226 DTM P S，D，m，n Data conversion and move

S     
D    
m   
n   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S  
D  
m  
n  

AS AS -
Symbol
S : Source data device
D : Device where the conversion result is stored
m : Conversion mode selection
_6 n : The length of the data to be executed
Explanation
1. The parameter m is for you to select a conversion mode from the following table. See the details on modes in the
following sections. If the parameter value is not one of the values in the following table, there will be no data
conversion or move and no error message.
6-406
Parameter Description
0 8-bit data converted into 16-bit data (high 8 bits, low 8 bits)
1 8-bit data converted into 16-bit data (low 8 bits, high 8 bits)
2 16-bit data (high 8 bits, low 8 bits) converted into 8-bit data
3 16-bit data (low 8 bits, high 8 bits) converted into 8-bit data
4 8-bit hex data (high 4 bits, low 4 bits) converted into ASCII data
5 8-bit hex data (low 4 bits, high 4 bits) converted into ASCII data.
6 8-bit ASCII data converted into hex data (high 4 bits, low 4 bits).）
7 8-bit ASCII data converted into hex data (low 4 bits, high 4 bits).
String-type data converted into floating-point data (available for FW V1.08 or later)
18
Floating-point data converted into string-type data (available for FW V1.08 or later)
19
42 Caculate the duration of 2-Axis relative-position clockwise arc interpolation
43 Caculate the duration of 2-Axis relative-position counterclockwise arc interpolation
44 Set up the built-in input points filtering time for the PLC
Caculate the relative -position pulse output time in acceleraton and deceleration (available for FW
46
V1.08 or later)
6_
2. n is the setting value of data length. The range of the setting value is 1~256. If the input value exceeds the range,
the PLC will execute the instruction at the minimum or maximum value.
3. The conversion modes and move modes are explained as below.
 When m=0:
If n=4, the 8-bit data is converted into the 16-bit data (high 8-bits, low 8-bits), the conversion is as the
following figure shows.
Hi-byte Lo-byte
 Hi-byte Lo-byte
  
  

6-407
 When m=1:
If n=4, the 8-bit data is converted into the 16-bit data (low 8-bits, high 8-bits), the conversion is as the
Hi-byte Lo-byte
 Hi-byte Lo-byte
  
  

 When m=2:
If n=4, the 16-bit data (high 8-bits, low 8-bits) is converted into the 8-bit data, the conversion is as the
Hi-byte Lo-byte
Hi-byte Lo-byte 
  
  

_6  When m=3:
If n=2, the 16-bit data (low 8-bits, high 8-bits) is converted into the 8-bit data, the conversion is as the
Hi-byte Lo-byte
Hi-byte Lo-byte 
  
  

6-408
 When m=4:
If n=3, the 8-bit hex data (high 4-bits, low 4-bits) is converted into the ASCII data and the conversion is as
the following figure shows.
Hi-byte Lo-byte
Hi-byte Lo-byte H
 L
 H
 L
H
L
 When m=5:
If n=3, the 8-bit hex data (low 4-bits, high 4-bits) is converted into the ASCII data, the conversion is as the
Hi-byte Lo-byte
Hi-byte Lo-byte L
 H
 L
 H
L
H
6_
 When m=6:
If n=4, the 8-bit ASCII data is converted into the hex data (high 4-bits, low 4-bits), the conversion is as the
following figure shows. ASCII conversion values can be: 0 ~ 9 (0x30~0x39), A ~ F (0x41~0x46), a ~ f
(0x61~0x66).
Hi-byte Lo-byte
 Hi-byte Lo-byte
  
  

6-409
 When m=7:
If n=4, the 8-bit ASCII data is converted into the hex data (low 4-bits, high 4-bits), the conversion is as the
Hi-byte Lo-byte
 Hi-byte Lo-byte
  
  

 When m=18:
Convert the string value in source device S (Lo-byte) into a floating-point value (operand n; decimal point
excluded) and store this value in device D.
Note:
1. The setting value in operand n should be less than 8. If the value you set is exceeding the maximum
value 8, it will be treated as the maximumum value 8. For example if n = k6, when you convert the string
123.45678 into a floating-point value, the result is 123.456.
2. If the source value includes not just numeral characters, the non-numeral characters will be treated as 0
_6
when it is shown before the decimal point and it will be treated as the ending character when it is shown
after the decimal point. For example if n = k6, when you convert the string BC12.4K59 into a floating-
point value, the result is 0012.4.
3. If there is no decimal point in the string, the string is converted directly into a floating-point value. See
the illustration below for reference.
Hi-byte Lo-byte
S+0 ‘1’
S+1 ‘2’
S+2 ‘3’
32-bit Floating value
S+3 ‘.’ D+0
123.456
S+4 ‘4’ D+1
S+5 ‘5’
S+6 ‘6’
S+7 0x00
6-410
 When m=19:
Convert the floating-point value in source device S (Lo-byte) into a string value (operand n; decimal point
excluded) and store this value in device D.
Note:
1. The setting value in operand n should be less than 8. If the value you set is exceeding the maximum
value 8, it will be treated as the maximumum value 8. For example if n = k6, when you convert the
floating-point value F123.45678 into a string value, the result is 123.456.
2. If the source value is bigger than the setting value in the operand n, only the value before the decimal
point will be converted. For example, if the floating point value is F123456.78 and n is k4, the conversion
result is 1234. See the illustration below for reference.
Hi-byte Lo-byte
D+0 ‘1’
D+1 ‘2’
D+2 ‘3’
32-bit Floating value n = k6
S+0 D+3 ‘.’
123.45678
S+1 D+4 ‘4’
D+5 ‘5’
D+6 ‘6’
D+7 0x00
 When m=42: 6_
Operand S1:
S1+0, S1+1: X axis target coordinate (relative positioning)
S1+2, S1+3: Y axis target coordinate (relative positioning)
S1+4, S1+5: Shift of the center (integer type) or central angle (floating point type)
S1+6, S1+7: Target reference frequency (1~200000Hz; if exceeding the allowable range, the system uses the
maximum or minimum value instead)
S1+8: Function selections

(K0, K1, K2: Shift of the center mode; shifts at 10 degree, 5 degree or 1 degree)
(K10, K11, K12: Central angle; shifts at 10 degree, 5 degree or 1 degree)
Operand D: D+0, D+1: Calculation of the duration of 2-Axis relative-position clockwise arc interpolation; unit:ms
Operand m: Function code K42
Operand n: Reserved
6 - 4 11
 When m=43：
Operand S1:
S1+0, S1+1: X axis target coordinate (relative positioning)
S1+2, S1+3: Y axis target coordinate (relative positioning)
S1+4, S1+5: Shift of the center (integer type) or central angle (floating point type)
S1+6, S1+7: Target reference frequency (1~200000Hz; if exceeding the allowable range, the system uses the
maximum or minimum value instead)
S1+8: Function selections
(K0, K1, K2: Shift of the center mode; shifts at 10 degree, 5 degree or 1 degree)
(K10, K11, K12: Central angle; shifts at 10 degree, 5 degree or 1 degree)
Operand D: D+0, D+1: Calculation of the duration of 2-Axis relative-position anti-clockwise arc interpolation;
unit: ms
Operand n: Reserved
 When m=44:
Operand S1: the starting point of PLC input points (K0~K15  X0.0~X0.15)
Operand D: filtering time; unit: µs (0~20000)
Operand m: function code K44
Operand n: total number of input points to be updated

_6
 m=46:
Operand S1: S1+0, S1+1: number of pulse output (relative –position)
S1+2, S1+3: frequency of pulse output (AS324MT Y0.0/Y0.2: 1~4MHz; others: 1~200KHz)
S1+4: device of pulse output (K0~K11：Y0.0~Y0.11)
Operand D: D+0, D+1: Caculate the relative -position pulse output time in acceleraton and deceleration;
unit: ms
Operand n: Reserved
Additional remarks
1. Using the matrix variables of Word data type for S and D is recommended.
6-412
1227 ZSET P SBit, EBit Zone setup

SBit     
EBit     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
SBit 
EBit 

AS AS -
Symbol
SBit : Starting device of the zone
EBit : Ending device of the zone
Explanation
1. Set the bit in the zone between SBit and EBit to ON. The type of starting and ending devices should be the same
before setting up.

6_
2. If the number of SBit is larger than the number of EBit, only EBit can be set. Set the number SBit to a smaller one.
3. Eexcept T, C and HC devices, this instruction is available for bit-type devices and BOOL type data.
Example
1. When M0 is ON, the auxiliary relays M300~M399 are ON.
6-413
6.14 Structure Creation Instructions

6.14.1 List of Structure Creation Instructions
The following table lists the Data Processing instructions covered in this section.

API Function
1300 FOR – – Starting a nested loop
1301 NEXT – – Ending a nested loop
1302 BREAK – – Terminating a FOR-NEXT loop
_6
6-414
6.14.2 Explanation of Structure Creation Instructions
1300 FOR S Starting a nested loop

S   DWORD       
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

－ AS －
Symbol
S ： Number of times the loop is executed
Explanation
Refer to the NEXT instruction (API 1301) for more details.
6_
6-415
1301 NEXT － Ending a nested loop

－ AS －
Symbol
Explanation
1. This instruction executes the program between the FOR and NEXT instructions N times, where N is the value in S
specified for the FOR instruction (API 1300). After the program between the FOR and NEXT instructions is
executed N times, the program following the NEXT instruction is executed. The instruction FOR specifies the
number of times the program between the FOR and NEXT instructions is executed.
2. N must be between 1–32,767. If N is less than 1, the instruction processes it as 1.
3. If you do not want to execute the program between the FOR and NEXT instructions, you can skip it with the CJ
4. The following conditions result in errors.
 The NEXT instruction is prior to the FOR instruction.

_6
 The FOR instruction exists, but the NEXT instruction does not exist.
 The NEXT instruction follows the FEND or END instruction.
 The number of times the FOR instruction is used in the program is different from the number of times the
NEXT instruction is used in the program.
5. The FOR and NEXT instructions support the nested program structure. There can be at most 32 levels of nested
program structures. If a loop is executed many times, it takes more time for the PLC to scan the program, and the
watchdog timer error may occur. You can use the WDT instruction (API 1900) to resolve the problem.
6-416
Example 1
After program A is executed three times, the program following the instruction NEXT is executed. Program B is executed
four times every time program A is executed. Therefore, program B is executed twelve times in total.
Example 2
When X0.0 is OFF, the program between FOR and NEXT is executed. When X0.0 is ON, the CJ instruction is executed.
The execution of the program jumps to LABEL 1:, i.e. network 6, and network 4–5 are not executed. 6_
6-417
Example 3
If the program between FOR and NEXT is not to be executed, you can skip it with the CJ instruction. When X0.1 in
network 8 is ON, the instruction CJ is executed. The execution of the program jumps to LABEL 1:, i.e. network 12, and
network 9–11 are not executed.
_6
6-418
6_
6-419
Additional remarks
Refer to the ISPSoft User Manual for more information on using labels.
_6
6-420
1302 BREAK D Terminating the FOR-NEXT loop

D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  

－ AS －
Symbol
Device where the remaining number
D ： of times the loop can be executed is
stored
Explanation
1. This instruction terminates the FOR/NEXT loop. The remaining number of times the FOR/NEXT loop can be
repeated is stored in D. After the loop has executed D times, the program jumps to the NEXT instruction and
executes the instruction after the NEXT instruction.
6_
2. When the instruction is executed, the remaining number of times the FOR/NEXT loop can be repeated is stored in
D, including this time the instruction BREAK is executed.
3. When the BREAK instruction is executed for the first time to terminate the FOR/NEXT loop, the program does not
jump out of the FOR/NEXT loop to execute the next instruction. If the BREAK instruction is executed more than one
time to terminate the FOR/NEXT loop, the program jumps to the NEXT instruction and executes the instruction
following the NEXT instruction.
Example
When the FOR/NEXT loop is executed, 1 is added to the value in D0. When the value in D0 is equal to 30, the
FOR/NEXT loop is terminated, and the remaining number of times the FOR/NEXT loop can be repeated, i.e. 71, is stored
in D10. The execution of the program jumps to LABEL 1:, i.e. network 6, and 1 is added to the value in D2.
6-421
_6
Additional remarks
1. If the instruction BREAK is outside the FOR/NEXT loop, it causes an operation error, the instruction is not
2. Refer to the ISPSoft User Manual for more information on using labels.
6-422
6.15 Module Instructions

6.15.1 List of Module Instructions
The following table lists the Module instructions covered in this section.

API Function
1400 FROM DFROM  Reading data from the control register in an extension module
1401 TO DTO  Writing data into the control register in an extension module
1402 PUCONF DPUCONF  Setting output control parameters of PU module

1403 PUSTAT – – Reading PU module output state
1404 – DPUPLS – PU module pulse output (no acceleration)
1405 – DPUDRI –
(with acceleration and deceleration)
Absolute addressing output of PU module
1406 – DPUDRA –
1407 – DPUZRN – PU module homing
1408 – DPUJOG – PU module jog output
1409 – DPUMPG – PU module MPG output
1410 – DPUCNT – High-speed counter function of PU module
1415 – DLCCAL – LC module channel calibration
1416 – DLCWEI – Reading weight value via LC module
1417 – DMPID – PID algorithm for RTD/TC module
1418 – DHCCNT – HC module counter value counted 6_
1419 – DHCCAP – HC module counter value captured
1420 HCDO – – HC module digital output point
1421 – DHCCMP – HC module counter value in comparison for output
1422 – DHCCMPT – HC module counter value in group comparison for output
1423 – DHCMEAS – HC module measurements of frequency and revolution
1426 IOLINKR – – Read the parameter from the O-Link device
1427 IOLINKW – – Write the parameter into the IO-Link device
6-423
6.15.2 Explanation of Module Instructions
Reading data from the control

1400 D FROM P m1, m2, m3, D1, D2, n
register in an extension module

m1         
m2         
m3         
D1    
D2    
n         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
m1    
m2    
m3    
D1    
D2    
n    

AS AS AS
_6 Symbol
CPU module number or the remote

m1 ：
extension module number
Order numbers of the extension
m2 ：
number
m3 ： Control register number
D1 ： Device where the data is stored
D2 ： Device where the error code is stored
n ： Data length
6-424
Explanation
1. This instruction reads data from the control register in an extension module.
2. The value in m1 must be between 0–16. Zero represents the CPU module, and 1–16 represent the extension
modules.
3. The operand m2 represents the number of the right-side extension modules that are connected to the CPU module
or to the remote modules. The first device is number 1, the second device is number 2 and so on. Any types of
connected modules are counted and up to 32 devices can be connected.
4. The operand m3 specifies the control register number.
5. The FROM instruction sets D2 to 0. When an error occurs, the instruction does not set D2 to 0. Please refer to the
Additional remarks below for more information about the error codes. When the instruction is not executed, D2
does not contain an error code.
Example
6_
When X0.0 is switched from OFF to ON, the instruction reads the data stored in CR#2 from the right side of the first
module and stores the data in D100. If no error occurs, the code in D110 is 16#0000.
Additional remarks
1. If the values in m1 and m2 exceed their range, an operation error occurs, the instruction is not executed, SM0 is
2. If D1 to D1+n-1 exceed the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in n exceeds the range, the operation error occurs, the instruction is not executed, SM0 is ON, and the
6-425
4. Due to the fact that the FROM instruction decreases the execution efficiency of both the CPU module and the I/O
module, it is suggested that you use the pulse type instruction to perform a single trigger as in the example shown
above.
5. If there is any error response from the modules, the instruction stores the error code in D2. The error code
descriptions shown in the following table.
Attempted to read the data from the control register (CR) in the module but no such CR
16#1400
number exists.
16#1401 The value is not valid for the module.
16#1402 The module is not responding, communication timeout.
_6
6-426

Writing data into the control register in an
1401 D TO P m1, m2, m3, S, D, n
extension module
m1         
m2         
m3         
S       
D    
n         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data INT
type
m1    
m2    
m3    
S    
D    
n    

AS AS AS
Symbol 6_
CPU module number or the remote
m1 ：
extension module number
Order numbers of the extension
m2 ：
number
m3 ： Control register number
S ： Device where the data is stored
D ： Device where the error code is stored
n ： Length of the data to be written
6-427
Explanation
1. This instruction writes data to the control register in an extension module.
2. The value in m1 must be between 0–16. Zero represents the CPU module, and 1–16 represent the extension
modules.
3. The operand m2 represents the number of the right-side extension modules that are connected to the CPU module
or to the remote modules. The first device is number 1, the second device is number 2 and so on. Any types of
connected modules are counted and up to 32 devices can be connected.
4. The operand m3 specifies the control register number.
5. The TO instruction sets D to 0. When an error occurs, the instruction does not set D2 to 0. Please refer to the
Additional remarks below for more information about the error codes. When the instruction is not executed, D does
not contain an error code.
6. The operand m1 must be between 1–8.
8. When S is a hexadecimal value, the instruction transmits n hexadecimal values to the I/O module. Supposing S is
16#0001 and n is 3. The instruction transmits three 16#0001s to the I/O module.
_6 Example
When X0.0 switches from OFF to ON, the TO instruction writes the data stored in D100 to CR#2 in the right side of the
first module. If no error occurs, the code in D110 is 16#0000.
6-428
Additional remarks
1. If the values in m1 and m2 exceed their range, an operation error occurs, the instruction is not executed, SM0 is
2. If D1-D1+n-1 exceed the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in n exceeds the range, the operation error occurs, the instruction is not executed, SM0 is ON, and the
4. Due to the fact that the TO instruction decreases the execution efficiency of both the CPU module and the I/O
module, it is suggested that you use the pulse type instruction to perform a single trigger as in the example shown
above.
5. If there is any error response from the modules, the instruction stores the error code in D2. The error code
descriptions are shown in the following table.
Attempted to read the data from the control register (CR) in the module but no such CR
16#1400
number exists.
16#1401 The value is not valid for the module.
16#1402 The module is not responding, communication timeout. 6_
6-429

Setting output control parameters of
1402 D PUCONF P Module ~ Error, ErrCode
PU module
Module   
Axis   
Mode   
SSpeed   
Atime   
Dtime   
MSpeed   
Z_no   
Offset   
Done    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Module  
_6 Axis  
Mode  
SSpeed  
Atime  
Dtime  
Mspeed  
Z_no  
Offset  
Done 
Error 
ErrCode  

AS － AS
6-430
Symbol
Module : Module number
Axis : Output axis number
Mode : Output mode

SSpeed : Speed for starting/ ending frequency
Atime : Acceleration time
Dtime : Deceleration time
MSpeed : Maximum output frequency
Number of Z phases to look for after returning to the
Z_no :
home position
Specify the number of outputs after returning to the
Offset :
home position
Done : Completion flag
Error : Error flag
ErrCode : Error code
Explanation
1. This instruction is available for PLC with FW V1.08.00 or later.
2. Module sets the serial number of modules at the right of the PLC. The first one is number 1, the second one is
number 2 and so on. Whatever modules at the right of the PLC must be numbered. The maximum number is 32.
The instruction is exclusive to the PU modules at the right of the PLC and is not applicable to the PU modules at the
right of the remote module. If the specified module is not a PU module, the error flag Error will change to ON.
3. Axis sets the output axis number for the specified PU module. The setting values 1~4 represent the axis1~axis4 6_
output of the specified PU module respectively. If the PU module has no corresponding axis number for output, the
error flag Error will change to ON.
See the following combination of axis numbers and corresponding output points of PU modules.
PU module name Axis 1 Axis 2 Axis 3 Axis 4
AS02PU Y0.0 / Y0.1 Y0.2 / Y0.3 NA NA
AS04PU Y0.0 / Y0.1 Y0.2 / Y0.3 Y0.4 / Y0.5 Y0.6 / Y0.7
4. Mode sets the output mode of an output axis and the setting values are explained in the following table.
Output mode
Description Remark
value
Single-point pulse output (An even-number

0 E.g. Y0.0 or Y0.2 for output
point for output only)
Pulse (An even-number point) + direction E.g. Y0.0 is for the pulse and Y0.1 is for the
1
(An odd-number point) direction. Y0.1: ON, negative direction;
6-431
Y0.1: OFF, positive direction
CW (An even-number point) + CCW (An E.g. Y0.0 is for CW (positive direction) and
2
odd-number point) Y0.1 is for CCW (negative direction)
E.g. Y0.0 is for phase A and Y0.1 is for
Phase A (An even-number point) + Phase B phase B. When phase A is leading phase B:
3
(An odd-number point) positive direction; when phase B is leading
phase A: negative direction
Automatically switch to mode 1 (default

Other value
value)
5. SSpeed~ Offset
See the explanation of the following non-latched parameters and setting values. If the setting values exceed the
range, the instruction will automatically be executed at the minimum or maximum value.
Parameter Function Range Default Remark
SSpeed Starting/ending frequency 0 ~ 10,000 (Unit: Hz) 100
Atime Acceleration time 0 ~ 10,000 (Unit: ms) 100
Dtime Deceleration time 0 ~ 10,000 (Unit: ms) 100
AS02PU: 100 ~ 200,000

200K
(Unit: Hz)
_6
MSpeed Maximum output frequency A 32-bit value
AS04PU: 100 ~ 100,000
100K
(Unit: Hz)
Number of Z phase signals to seek

Z_no -100 ~ 100 (Unit: times) 0 0: disabled
after returing to the origin.
Outputs the offset position after the

-10,000 ~ 10,000 (Unit:
Offset homing is finished and Z phase 0 0: disabled
pulses)
seeking is done.
6. Done, an output of the specified PU module has been set as the completion flag. When Done is On, it indicates
that the parameter setting is successful. You can continue to perform positioning output based on the state of the
completion flag (ON). The clearing of the Done flag need be conducted by manual. The Done flag changes to ON
only when the setting is completed.
7. Error, an output of the specified PU module is a parameter error flag. Most parameter ranges are filtered
automatically by the PLC. Thus if the error flag is ON, it means that there is no specified PU module or the PU
module number is wrong or the output axis number is incorrect.
6-432
8. The instruction is a pulse instruction. Even if the A contact is adopted as the condition contact, PU module
parameters are also set only when the instruction is started. Therefore, if a parameter value is to be updated,
restart the instruction to make the parameter set again.
9. Since the set parameters are delivered through the module communication command, confirm the state of the
output Done or Error before a parameter value is modified and then proceed with relevant operations.
10. ErrCode shows error codes. See the description as follows.
16#1400 The module does not support the function.
16#1401 The data stored in the module is illegal or exceeds the allowed range.
16#1402 There is no response from the module; communication timeout occurs.
6_
6-433
1403 PUSTAT Module ~ ErrCode Reading PU module output state
Module   
Axis   
ZeroS     
C_Posi 
Execute    
Pause    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Module  
Axis  
ZeroS 
C_Posi  
Execute 
Pause 
_6 Error 
ErrCode  

－ AS －
Symbol
ZeroS : Clear present output position to 0

C_Posi : Current output position
Execute : Execution flag
Pause : Pause flag
Error : Error flag
6-434
Explanation
3. Axis sets the output axis number for the specified PU module. The setting values 1~4 represent the axis1~axis4
4. C_Posi sets the present position of the output axis for the specified PU module. The parameter value is a latched
value and stored in the PU module. If the value is to be cleared to 0, set ZeroS from OFF to ON when the instruction
is started.
5. Execute is an only-read flag which means the output axis of the specified PU module is outputting or not. When
Execute is On, it means the output is being conducted. When Execute is Off, it means the output axis is unused
and can accept the next output command.
6. Pause is an only-read flag to control the output axis of the specified PU module to pause its output. When Pause is
On, it means the output is paused, the present velocity is 0 and the present output has not reached the specified
target output position. If you restore the output, the flag will be cleared automatically.
Note: While Pause is On, Execute is constantly On as well.
7. Error is an only-read error flag which means an error occurs during the reading of the specified PU module. Refer 6_
to the explanation of error codes in ErrCode.
8. After the PUSTAT instruction gives the pause command, the flags Execute, Pause and Error become read-only
flags and at the moment, their states cannot be modified. The Execute, Pause and Error flags can be set or cleared
only when the PUSTAT instruction is turned off.
9. ErrCode shows error codes and the explanations are seen in the following table.
16#1403 There is no such output axis number in the PU module.
16#1404 The output frequency of the PU module is illegal.
The output axis specified by the PU module is outputting data. It is not allowed to specify
16#1405
the output repeatedly.
6-435

PU module pulse output
1404 D PUPLS Module ~ ErrCode
(no acceleration)
Module   
Axis   
TarPulse   
TarSpeed   
Done    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Axis  
TarPulse  
TarSpeed  
Done 
Error 
ErrCode  
_6 Pulse Instruction 16-bit instruction 32-bit instruction

－－ AS
Symbol
TarPulse : Target number of output pulses

TarSpeed : Target output frequency
Error : Error flag
Explanation
6-436
4. TarPulse sets the number of output pulses. The pulse number is a positive signed 32-bit value. When the value is
0, it means the output is always being performed, the number of output pulses is not limited and the output is not
stopped until the instruction is disabled. When the value is less than 0, the PLC automatically uses 2s complement
to transform the value into a positive integer as the number of output pulses.
5. TarSpeed sets the target output speed (Unit: Hz). The input value is a signed 32-bit. You can modify the target
frequency any time after the instruction is enabled and the PU module will automatically switch to the newly set target
frequency after outputting a full pulse.
Note: Before the target frequency is changed, please take into consideration whether the modified speed and PLC
scan time match or not.
Module Name TarSpeed Setting Range
AS02PU -200,000 (-200K) ~ 200,000 (200K)
AS04PU -100,000 (-100K) ~ 100,000 (100K)
6. When TarSpeed is a positive number (>0), it means that the “positive direction” output point is Off. When TarSpeed
is a negative number (<0), it means that the “negative direction” output point is On. When TarSpeed is 0, it means
that the output will be paused after the being executed pulse is output fully.
7. The instruction does not support the function of acceleration and deceleration. Use the DPUDRI instruction instead
if you need the function of acceleration and deceleration.
8. The instruction can be used for the speed change. While the instruction is being executed, you can change the value 6_
of TarSpeed so as to change the output speed.
9. When the outputs have reached the pulse number specified by TarPulse, the Done flag changes to ON. The Done
flag need be cleared by manual. The instruction sets the completion flag to ON only when the output is completed.
10. If any error occurs as the instruction is in process of the output, the Error flag changes to ON. Refer to the error
codes ErrCode shows for the trouble shooting.
The error codes that ErrCode shows are listed in the following table.
16#1401 The value stored in the module is illegal or exceeds the allowed range.
The output axis specified by the PU module is outputting data. It is not allowed to
16#1405
specify the output repeatedly.
6-437

1405 D PUDRI Module ~ ErrCode
Module   
Axis   
RTarPosi   
Done    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Axis  
RTarPosi  
TarSpeed  
Done 
Error 
ErrCode  
_6 Pulse Instruction 16-bit instruction 32-bit instruction

－－ AS
Symbol
RTarPosi : Number of output pulses for relative positioning

Error : Error flag
Explanation
6-438
4. RTarPosi sets the position for relative positioning. The pulse number is a signed 32-bit value. When the value is
greater than 0, the output will go in the positive direction (and the direction output point is off). When the value is less
than 0, the output will go in the negative direction (and the direction output point is on). When the value is 0, the
output completion flag Done changes to ON.
5. TarSpeed sets the target output frequency (Unit: Hz). The frequency value is a positive signed 32-bit integer. When
the value is less than 0, the instruction will automatically use 2’s complement to transform the value into a positive
integer. When the value is 0, the instruction will notify the module to enter the pause mode. The actual output is
decelerated at the deceleration rate till the output speed is equal to 0 and the pause flag changes to ON. Refer to
PUSTAT instruction for more details.
Module Name TarSpeed Setting Range
AS02PU -200,000 (-200K) ~ 200,000 (200K)
AS04PU -100,000 (-100K) ~ 100,000 (100K)
6. After the output is started, the target frequency is allowed to change any time. In the actual frequency change, the
PLC will automatically change the frequency based on the set acceleration and deceleration rate in the DPUCONF
instruction.
7. When the outputs have reached the pulse number for relative positioning specified by RTarPosi, the Done flag
changes to ON. The Done flag need be cleared by manual. The instruction sets the completion flag to ON only when 6_
the output is completed.
codes that ErrCode shows for the trouble shooting.
9. The error codes that ErrCode shows are listed in the following table.
16#1405
6-439
10. Illustration of the acceleration and deceleration curve of the DPUDRI instruction
Freq.
 
Time
Pulse No.
 
 : Maximum output frequency value. Refer to the setting in the DPUCONF instruction for the parameter setting.
Alternatively, set the parameter value through HWCONFIG.
: The target frequency specified by the PU module output instruction. The target frequency output must not exceed
the maximum output frequency. If the maximum output frequency is exceeded, the maximum output frequency is
regarded as the output frequency.
: Starting/ending output frequency value. Refer to the setting in the DPUCONF instruction for the parameter setting.
: The acceleration time value. Refer to the setting in the DPUCONF instruction for the parameter setting.
_6 Alternatively, set the parameter value through HWCONFIG.
: The deceleration time value. Refer to the setting in the DPUCONF instruction for the parameter setting.
The acceleration and deceleration that the PU module controls is performed according to the fixed slope. So the
actual acceleration time and deceleration time change based on the output target frequency. The formula for
calculation of acceleration rate and deceleration rate are respectively shown as follows.
(Max. output frequency - starting frequency)/acceleration time;
(Max. output frequency - ending frequency)/deceleration time.
6-440

Absolute addressing output of PU
1406 D PUDRA Module ~ ErrCode module
Module   
Axis   
ATarPosi   
Done   
Error   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Axis  
ATarPosi  
TarSpeed  
Done 
Error 
ErrCode  

6_
－－ AS
Symbol
ATarPosi : Number of output pulses for absolute addressing

Done : Completion/pause flag
Error : Error flag
6-441
Explanation
2. ATarPosi is the position for absolute addressing. The input pulse number is a signed 32 bit value. The PU module
will automatically compare it with the present position. If the comparison result is greater than 0, the output will be
conducted in the positive direction (and the direction output point is off). If the comparison result is less than 0, the
output will be conducted in the negative direction and the direction output point is on). When the value is 0, the
instruction sets the Done flag to ON.
3. Refer to the DPUDRI instruction for the explanation of other parameters.
_6
6-442
1407 D PUZRN Module ~ ErrCode PU module homing
Module   
Axis   
Mode   
JogSpeed   
Done   
Error   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Axis  
Mode  
TarSpeed  
JogSpeed  
Done 
Error 
6_
ErrCode  

－ AS AS
Symbol
Mode : Homing mode selection

TarSpeed : Maximum output frequency for the homing
JogSpeed : The jog frequency for the homing

Error : Error flag
6-443
Explanation
4. Mode sets a homing mode. The explanation of modes is shown in the following table.
Use matching
Mode input points

Function description Remark
value (set up in
HWCONFIG)
0 Directly clear current position to 0. None
Specify the point where DOG point is touched as
the home position; the axis starts to go toward

1 DOG
the negative direction and then stops after
leaving the DOG point position.

_6
Specify the point where DOG point is touched as
the home position; the axis starts to go toward

2 DOG
the positive direction and then stops after leaving
the DOG point position.
After the execution of Mode 1 completes, seek DOG and Z

3
the number of Z phases. phase input Use DPUCONF instruction to
After the execution of Mode 2 completes, seek DOG and Z set up the number of Z phases.
4
the number of Z phases. phase input
After the execution of Mode 1 completes, output

5 DOG
the offset positon. Use DPUCONF instruction to
After the execution of Mode 2 completes, output output the offset position.
6 DOG
the offset positon.
After the execution of Mode 1 completes, seek Use DPUCONF instruction to

DOG and Z
7 the number of Z phases and then output the set up the number of Z phases
phase input
offset positon. and then to output the offset
6-444
After the execution of Mode 1 completes, seek position.
8 the number of Z phases and then output the
offset positon.
Use the setting value of

255 Modify the current output position for the axis. None
TarSpeed
Other Reserved
Note 1: The specified homing behavior may not be realized if the input points for the selected mode are not used
together with the settings in HWCONFIG.
Note 2: Mode 1~4
FW V1.02.00: after the execution of this instruction, the current output position of the axis will not be cleared to zero.
You need to use the instruction PUSTAT to clear it.
FW V1.02.10 or later: after the execution of this instruction, the current output position of the axis will be cleared to
zero automatically.
Note 3: Mode 5~8
V1.02.00: after the execution of this instruction, the current output position of the axis will not be cleared to zero. You
need to use Mode 255 to modify the current output position to clear it.
V1.02.10 or later: after the execution of this instruction, the current output position of the axis will be cleared to zero
automatically.
6_
5. TarSpeed sets the maximum output frequency for the homing when the mode value is between 1 to 8. The setting
value is a signed 32-bit value. When the value is a positive one, the direction of homing is positive. When the value
is a negative one, the direction of homing is negative.
Module Name TarSpeed Setting Range when the mode is between 1 to 8.
AS02PU -200,000 (-200K) ~ 200,000 (200K)
AS04PU -100,000 (-100K) ~ 100,000 (100K)
If the mode is 255, the value in TarSpeed is updated as the current output position of the PU module.
6. JogSpeed is the jog frequency for reaching the home position. The setting value is a signed 16 bit value within the
range of 1~10,000 (Hz).
7. When the specified operation is complete during the execution of the instruction, the Done flag changes to ON. The
Done flag need to be cleared manually. The instruction sets the completion flag to ON only when the output is
completed.
6-445
16#1405
_6
6-446
1408 D PUJOG Module - ErrCode PU module jog output
Module   
Axis   
JogSpeed   
Busy    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Axis  
JogSpeed  
Busy 
Error 
ErrCode  

－－ AS
Symbol 6_
JogSpeed : Jog output frequency

Busy : Output in execution
Error : Error flag
Explanation
6-447
4. JogSpeed sets the jog output frequency. The setting value is a signed 32 bit value. When the value is greater than
0, the output will go in the positive direction (and the direction output point is off). When the value is less than 0, the
output will go in the negative direction (and the direction output point is on). When the value is 0, the output will stop.
Module Name JogSpeed Setting Range
AS02PU -200,000 (-200K) ~ 200,000 (200K)
AS04PU -100,000 (-100K) ~ 100,000 (100K)
16#1405
7.
_6
See the output timing diagram as below. (Jog_in is the switch to start the instruction and the Busy flag is the Busy
flag.)
Jog _in
Bu sy fl ag
JogSpeed > 0 I ncrease Decrease
0 Time
I ncrease Dec rease

JogSpeed < 0
8. After the PUJOG instruction is disabled and the Busy flag is off, other output control can be carried out.
6-448
1409 D PUMPG Module ~ ErrCode PU module MPG output
Module   
Axis   
InMode   
InPulse 
InSpeed 
Rate  
OPulse 
OSpeed 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Module  
Axis  
InMode  
InPulse  
InSpeed  
6_
Rate 
OPulse  
OSpeed  
Error 
ErrCode  

－－ AS
Symbol

Encoder input mode and frequency multiplication for
InMode :
counting
InPulse : Number of pulses which have been input
InSpeed : Detected input frequency
Rate : Input/output rate (floating point number)
OPulse : Number of pulses which have been output

OSpeed : Frequency at which pulses are being output
6-449
Error : Error flag

Explanation
2. The PUMPG instruction is only applicable to AS02PU module and the firmware for the module must be V1.04.00 or
above.
5. InMode sets the input mode of the encoder source and the frequency multiplication for counting.
See the explanation of InMode value in the following table.
Note: Phase A leads phase B, indicating counting in the positive direction.
Phase B leads phase A, indicating counting in the negative direction
Value Input Modes
16#0000 Reset to defaults

_6 16#0001 Onefold frequency A/B phase input
16#0002 Twofold frequency A/B phase input
16#0004 Fourfold frequency A/B phase input
Pulse + directional input (A+/A-: pulse input; B+/B-: directional input)
Phase B OFF: counting in the positive direction;

16#0005
Phase B ON: counting in the negative direction
Phase A is counted by rising-edge triggered.
Phase B ON: counting in the positive direction

16#0006
Phase B OFF: counting tin the negative direction
Single phase pulse input (A+/A-: pulse input)

16#0007
others Reset to defaults
6-450
6. InPulse displays the number of already input pulses, which is a signed 32-bit value. Every time the instruction is
started, the PU module will automatically clear the value to 0 and then starts counting.
7. InSpeed displays the already detected input frequency which is a 32-bit value. The basic time for the frequency
detection is 20ms. Therefore, the detected input frequency is 0 if there is no counting value within 20ms. If there is
a counting value within 20ms, the output starts at the minimum frequency of 50Hz. Even if OSpeed value is lower
than 50Hz through the Rate-value-based conversion, the output is still conducted at 50Hz.
8. Rate is the input / output rate and the value is a floating point number. The number of actual output pulses and
frequency are respectively equal to the input pulse number and frequency multiplied by the rate value.
For example: The input frequency is 100Hz and rate is 0.5. So the output frequency is 100x0.5=50Hz. If the
maximum output frequency after conversion exceeds 100KHz, the output frequency is limited to 100KHz.
Note: The long-time maximum frequency output may lead to the fact that as the MPG has stopped running, the
number of outputs is still increased and the output need keep going until it is complete.
9. OPulse shows the number of pulses which have been output. OSpeed displays the frequency at which the output
is being conducted. They are signed 32-bit values.
10. When the DPUMPG instruction is disabled, check the frequency at which the output is being conducted and see if it
has reached 0. If the instruction is disabled before the frequency reaches 0, the PU module will stop the output
immediately and the output of the pulses which are counted based on the conversion rate will not continue any more.
11. The error codes that ErrCode shows are listed in the following table. 6_
16#1405
12. When the DPUMPG instruction is enabled or disabled, the PLC will have to notify the module to enable or disable
the high-speed counter function. Thus the instruction can not be used with API1410 DPUCNT together. Otherwise it
may occur that the two instructions enable or disable the counting of the module with each other.
6-451

High-speed counter function of PU
1410 D PUCNT Module ~ ErrCode
module
Module   
InMode   
Period   
ZeroS     
InPulse 
InSpeed 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Module  
InMode  
Period  
ZeroS 
InPulse  
InSpeed  
_6 Error 
ErrCode  

－－ AS
Symbol

Encoder input mode and frequency multiplication for
InMode :
counting
Period : Period time for capturing the frequency
ZeroS : Clear the counter to 0

InPulse : Number of pulses which have been input
InSpeed : Number of pulses per cycle
Error : Error flag

Explanation
2. The DPUCNT instruction supports AS02PU module only.
6-452
4. InMode sets the input mode of the encoder source and the frequency multiplication for counting.
See the explanation of InMode value in the following table.

Note: Phase A leads phase B, indicating counting in the positive direction.
Phase B leads phase A, indicating counting in the negative direction
Value Input Modes
16#0001 Onefold frequency A/B phase input
16#0002 Twofold frequency A/B phase input
16#0004 Fourfold frequency A/B phase input
Phase B OFF: counting in the positive direction;

16#0005
Phase B ON: counting in the negative direction
Phase B ON: counting in the positive direction 6_

16#0006
Phase B OFF: counting tin the negative direction
Single phase pulse input (A+/A-: pulse input)

16#0007
others Reset to defaults
5. Period is the setting value of a cycle time for capturing the frequency within the range of 10ms ~ 1000ms. If the
setting value exceeds the range, the maximum value or minimum value will be automatically taken as the setting
value by the PLC.
6. InPulse is the number of already input pulses, which is a signed 32-bit value. The counting value is a latched value.
If the value need be cleared to 0, just set ZeroS from OFF to ON while the instruction is running.
7. InSpeed displays the counting value for every Period time, which is a signed 32-bit value. If you need convert it into
the value with the unit of Hz, use the calculation formula for conversion by yourself.
6-453
16#1406 The PU module does not support the counting function.
9. When the DPUCNT instruction is enabled or disabled, the PLC will have to notify the module to enable or disable
the high-speed counter function. Thus the instruction can not be used with API1409 DPUMPG together. Otherwise
it may occur that the two instructions enable or disable the counting of the module with each other.
_6
6-454
1415 D LCCAL Group, Module ~ ErrCode LC module channel calibration
Group   
Module   
ChNo   
Trigger     
TPoint   
TWeight 
CPoint 
Done    
ADone    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Group  
Module  
ChNo   6_
Trigger 
TPoint  
TWeight 
CPoint  
Done 
ADone 
Error 
ErrCode  

－－ AS
Symbol
Group : Group number
ChNo : Channel number

Trigger : Trigger the calibration
TPoint : Number of all calibration points
TWeight : Calibration weight value
6-455
Number of the point for which the calibration has

CPoint :
been completed.
Done : Single-calibration-completed flag
ADone : All-calibration-completed flag
Error : Error flag

Explanation
1. This instruction is available for PLC with FW V1.08.00 or later and ISPSoft V3.09 or later.
2. The LCCAL instruction supports AS02LC module only. Before the instruction is used, you should get to know the
configuration position of current module from HWCONFIG.
3. Group is the group number of the specified LC module connected to the right of the PLC or the remote module. The
number of the PLC is 0, the number of the first remote module is 1 and so on. The maximum group number is 15.
If the specified module is not a LC module, the Error flag will change to ON.
number 2 and so on. Whatever modules at the right of the PLC must be numbered. The maximum number is 32. If
the specified module is not a LC module, the error flag Error will change to ON.
5. ChNo is a channel number of the specified LC module. If the input value is not a channel number of the LC module,
the error flag Error will change to ON.
6. Trigger is the command of triggering the single-point calibration. As Trigger changes from OFF to ON, the LC module
will be notified for calibration. Done changes to ON when the calibration is done. If all-point calibration has been
_6 done, ADone will changes to ON as well. Before the next calibration point is calibrated, you need observe that Done
has changed to ON and then set Trigger to OFF. Then the instruction will clear the Done flag as Trigger changes
from ON to OFF.
7. TPoint is the number of total points for calibration. After the instruction is started, the value can not be changed again
since the TPoint value has been transmitted to the LC module for calibration as the instruction is started initially.
8. TWeight is the calibration weight value and it occupies two devices. If the TPoint is 3 and the starting device for
TWeight is D200, here TWeight occupies 6 devices, D200~D205. The calibration weight value for the first TPoint
is in D200 (Low Word) and D201 (High Word). The calibration weight value for the second TPoint is in D202 (Low
Word) and D203 (High Word). The calibration weight value for the third TPoint is in D204 (Low Word) and D205
(High Word). Once the execution of this instruction started, the value of TWeight is sent to the LC module for
calibration. You cannot change the value of TWeight after the instruction is executed. the value of the first point for
calibration weight should be 0 (zero correction). If not, the Error flag will be ON.
9. Once ADone changes from OFF to ON, the entire calibration will be stopped. The calibration can be performed again
if the LCCAL instruction is enabled again after disabled.
10. CPoint is the number of points which have been calibrated and can not be modified by users. When CPoint value >=
TPoint value, the calibration is considered to be completed and the ADone flag changes to ON.
11. When the LCCAL instruction is enabled initially, the CPoint value is automatically cleared to 0 and Trigger, Done
6-456
and ADone change to OFF and the calibration is prepared. After Trigger is set from OFF to ON and the LC module
completes the calibration, the value of CPoint will be automatically added by 1 and the Done flag changes to ON.
You can observe current points for which the calibration has been completed via the value. For example, as the
CPoint value is 2, it means that Trigger is triggered twice and the module has completed the 2-point calibration.
16#1410 Error in the LC group number or module number
16#1411 The LC module has no such channel number
16#1412 LC module writing error or communication timeout
16#1413 The LC module has completed the calibration. Disable the instruction and retrigger it.
16#1414 The first value for calibration weight is not 0.
16#1415 The calibration weight value is not a floating-point value.
16#1416 The value exceeds the measuring range.
16#1417 The value exceeds the weight limit.
16#1418 Calibration error
13. See the sequence diagram in a calibration example.
6_
Explanation of the timing points in the above sequence diagram:
  The LCCAL instruction is enabled and the CPoint value and the flags Trigger, Done, ADone and Error are all
cleared automatically.
  Trigger the calibration flag.
  The instruction finds a module number error and displays the error code of LC module number error
6-457
  Disable the LCCAL instruction.
  After a trigger, the LC module completes the single-point calibration and the CPoint value is added by 1 and the
Done flag changes to ON.
  Clear the trigger signal flag Trigger.
  Subsequently, the Done flag is cleared by the instruction.
  After a trigger, the LC module completes the entire calibration and the CPoint value is added by 1 and both of
the flags Done and ADone change to ON.
Example
When PLC runs, the value of the first point for calibration weight is 0 written in D0 and D1. The value of the second point
for calibration weight is 500.0 written in D2 and D3.
  When M0 switches to ON, you can use DLCCAL instruction to calibrate.
  Make sure there is no load on the weighing platform. Set M50 to ON and then start zero correction (set the value of
the first point to zero). When D100 = 1 and M100 is ON, you have the first point calibrated. M50 switches to OFF.
  Put a 500 g weight on the weighing platform, set M50 to ON and then start a 500 g calibration for the second point.
When D100 = 2 and M101 is ON, you have the second point calibrated. M50 switches to OFF and MO to OFF.
_6
6-458
1416 D LCWEI Group, Module ~ ErrCode Reading weight value via LC module
Group   
Module   
ChNo   
Stable   
ZeroS     
TareS     
TareW 
Weight 
Status 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Group  
Module  
ChNo   6_
Stable  
ZeroS 
TareS 
TareW 
Weight 
Status  
Error 
ErrCode  

－－ AS
Symbol
Stable : Specify stable-weight range (0.0~100000.0)

ZeroS : Clear the weight to 0
TareS : Flag to set the tare weight
6-459
TareW : Tare weight value
Weight : Present weight value

Status : Status code of LC module
Error : Error flag
Explanation
2. The LCWEI instruction supports AS series LC module only. Before the instruction is used, you should get to know
the configuration position of current module from HWCONFIG.
3. Group is the group number of the specified LC module connected to the right of the PLC or the remote module. The
number of the PLC is 0, the number of the first remote module is 1 and so on. The maximum group number is 15.
If the specified module is not a LC module, the Error flag will change to ON.
number 2 and so on. Whatever modules at the right of the PLC must be numbered. The maximum number is 32. If
the specified module is not a LC module, the error flag Error will change to ON.
5. ChNo is a channel number of the specified LC module. If the input value is not a channel number of the LC module,
the error flag Error will change to ON.

_6
6. Stable sets a value within the stable-weight range. It is a raw data. The value can be set to a floating-point value
within the range of 0.0~100000.0 and the maximum value or minimum value will be automatically taken as the setting
if the setting value exceeds the range. The timing of making the parameter value valid is when the instruction is
enabled for the first time. If the value in the LC module need be modified, disable the instruction first, set a new range
value and then enable the instruction for a new setting.
7. After the LCWEI instruction is enabled, the specified channel will be automatically changed into the display mode of
“net weight”. If you need to know the gross weight (total weight), add TareW value and Weight value by yourself.
8. ZeroS is the flag to set the present weight to 0. When the ZeroS flag changes from OFF to ON, the values of TareW
and Weight are cleared to 0.
9. TareS is the flag to set the tare weight. When TareS changes from OFF to ON, present Weight value is moved to
TareW and the Weight value will be cleared to 0. When TareS changes from ON to OFF, TareW value will be moved
back to the present Weight value and the TareW value will be cleared to 0.
10. Weight is the weight value measured by deducting the tare weight. You can observe if the TareW value exists or not
in order to know whether the tare weight function has been enabled. When the TareW value is 0, it indicates that the
tare weight has not been set.
6-460
11. Status is a commonly used status code for the instruction to integrate LC module. See the explanation of status
values in the following table.
Value 0 1 2 3 4 5
Module
Hardware
Weight Weight number error
Weight is fault/
Description measuring or In calibration exceeds the /channel
stable calibration
no load range number
fault
error
12. During the weight reading, Status will display corresponding error code and the Error flag changes to ON as an
error occurs in the LC module. When the status returns to normal, the Error flag will be cleared automatically. For
details on error status, refer to the explanation of status control buffers in the LC module manual.
13. See the sequence diagram of the weight-reading example.
En
ZeroS
TareS
TareW 0 10 0 20 0
Weight 0 10 0 10 20 0 100 120
Status 0 1 0 1 0 1
6_
           
Explanation of the timing points in the above sequence diagram:
  Enable the LCWEI instruction.
  After getting the command of clearing data to 0, the instruction will clear the values of TareW, Weight and Status.
  Put the measured stuff on the weighing platform. When the stable weight value is measured, the Status value
becomes 1 and Weight displays the weight value.
  Setting TareS to ON, the Weight value moves to TareW and then the value of Weight is cleared.
  Setting TareS to OFF, the TareW value moves back to Weight and then the TareW value is cleared.
  Put another measured stuff on the weighing platform. At the moment, Status enters the status of weight
measuring.
  Disable the LCWEI instruction. TareW, Weight and Status hold the last status values.
6-461
16#1410 Error in the LC group number or module number
16#1411 The LC module has no such channel number
16#1414 Error in data-writing or communication timeout on LC module
Example
After calibration is done, you can use DLCWEI instruction to weigh.
1. Weighing: Leave a weight of 500 g on the weighing platform. When M1 switches to ON, the value in D204 shows
500.0.
2. Set up the tare weight
  Leave a packaging (100 g) on the weighing platform. The value in D204 shows 100.0.
  When M151 switches to ON, Weight value (D204) is moved to TareW value (D202). After moving, clear the
weight value in D204.
  D204 = 0.0 and D202 = 100.0. The setup of tare weight is complete.
3. Clear the tare weight
  When M151 switches to OFF, the TareW value (D202) is moved back to Weight value (D204). After moving,
clear the TareW value in D202.
_6   D202 = 0.0 and D204 = 100.0. The setup of clearing the tare weight is complete.
4. Specify a stable-weight range (checking the stability)
  Before executing this instruction, you need to specify the stable-weight range. Here we set D200 = 10.0.
  Leave a 500 g weight on the weighing platform. When the measurement result is between 490 ~ 510 g,
D210 =1 (the weight is stable).
6-462
1417 D MPID Group, Module ~ Error PID algorithm for RTD/TC module
GROUP   
MODULE   
CH   
UPDATE     
PID_RUN     
SV   
PID_MODE   
PID_MAN     
MOUT_AUTO     
AUTO_DBW   
Kc_Kp  
Ti_Ki  
Td_Kd  
Tf  
PID_EQ     
PID_DE     
6_
PID_DIR     
ERR_DBW 
ALPHA   
BETA   
MOUT 
BIAS   
CYCLE   
MV 
PV 
I_MV 
ERROR 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Refer to the following data type Pulse Instruction 16-bit instruction 32-bit instruction
descriptions －－ AS
6-463
Symbol
GROUP : Group number
MODULE : Module number
CH : Channel number
UPDATE : Update PID parameters
PID_RUN : Enable the PID algorithm
SV : Target value (SV)
PID_MODE : PID control mode
PID_MAN : PID Auto/Manual mode
MOUT_AUTO : Manual/Auto output value
Range within which the auto tuning is not

AUTO_DBW :
working
Kc_Kp : Proportional gain
Ti_Ki : Integral coefficient (sec. or 1/sec)
Td_Kd : Derivative coefficient (sec)
Tf : Derivate-action time constant (sec)
PID_EQ : PID formula types
_6 PID_DE : Calculation of the PID derivative error
PID_DIR : PID forward/reverse direction (PID_DIR)
ERR_DBW : Range within which the error value is counted as 0
Initial value compensation of integral

ALPHA :
calculus (for heating up)
Initial value compensation of integral

BETA :
calculus (for cooling down)
MOUT : Manual output value (MOUT)
BIAS Feed forward output value
CYCLE Sampling time (CYCLE)
MV Output value (MV)
PV Process value (PV)
I_MV Accumulated integral value
ERROR : Error code
6-464
Explanation
1. This instruction is available for PLC with FW V1.06.00 or later and can only support the right-side modules. For PLC
with FW V1.08.00 or later, it can support remote right-side modules (AS00SCM-A with FW V2.06 or later) as well.
2. This instruction is available for AS04RTD-A (V1.04 or later), AS06RTD-A (V1.00 or later), AS04TC-A (V1.04 or later),
and AS08TC-A (V1.00 or later).
3. The parameter settings are listed in the following table.
The RTD/TC module group number
that is connected to the right side of
PLC directly or connected to the
remote module that acts as PLC, e.g.
GROUP DWORD/DINT Group number the first connected module group is
group number 1, the second
connected module group is group
number 2. Up to 15 module group can
be connected and counted.
The module number that is connected
to the right side of PLC directly or
connected to the remote module that

6_
acts as PLC, e.g. the first connected
module is module number 1, the
MODULE DWORD/DINT Module number
second connected module is module
number 2. Up to 32 modules can be
connected and counted and each type
of modules should be included in the
count.
Channel number for PID algorithm,
e.g. channel 1 is number 1 for PID

CH DWORD/DINT Channel number
algorithm and channel 2 is number 2
for PID algorithm and so forth.
After enabling this instruction, you can
input a new parameter and set the

Flags for updates of the PID-
UPDATE BOOL UPDATE flag to TRUE to update the
related parameters
new setting and after updating, the flag
is switched to OFF automatically.
6-465
True: use the PID algorithm.
PID_RUN BOOL Enabling the PID algorithm False: reset the output value (MV) to
0, and stop using the PID algorithm.
SV DWORD/DINT Target value -32768~32767 Target value
0: Automatic control
When PID_MAN switches from True
to False, invoke the output value
(MV) in the automatic algorithm.
1: Auto tuning the parameters for the
temperature control. After tuning is
done, the system is in auto control

PID_MODE DWORD/DINT PID control mode
mode (PID_MODE is set to 0) and
fill in the appropriate parameters
(Kc_Kp, Ti_Ki, Td_Kd, Tf, APPHA
and BETA)
Note: when the mode is set to 1, auto
tuning the parameter, you
_6 cannot set up the value.
True: Manual
Output the MV according to
MOUT. This setting has no
effect when PID_MODE is set to

PID_MAN BOOL PID A/M mode
1.
False: Automatic
Output the MV according to the
PID algorithm.
True: Automatic
MOUT value varies with the MV.
MOUT_AUTO BOOL MOUT automatic change mode False: Normal
MOUT value does not vary with
the MV.
Range within which the auto Auto tuning NOT

AUTO_DBW DWORD/DINT 0~32000
tuning is not working activated when
6-466
SV is in the range
of± dead band
width
If the P coefficient
Range of is less than 0, the
Calculated proportional
positive single- Kc_Kp is 0.
coefficient (Kc or Kp,
Kc_Kp REAL precision Independently, if
according to the settings in
floating- Kc_Kp is 0, it is
PID_EQ)
point numbers not controlled by
P.
positive single- coefficient I is
Integral coefficient (Ti or Ki, precision less than 0, Ti_Ki
Ti_Ki REAL according to the settings in floating- is 0. If Ti_Ki is 0,
PID_EQ) point numbers it is not controlled
(unit: Ti = sec; Ki by I.
= 1/sec)
positive single- coefficient D is 6_

Derivative coefficient (Td or
precision less than 0,
Td_Kd REAL Kd, according to the settings
floating- Td_Kd is 0. If
in PID_EQ)
point numbers Ti_Ki is 0, it is not
(unit: sec) controlled by D.
If the derivate-
action time
Range of constant is less
positive single- than 0, Tf is 0 and
precision it is not controlled

Tf REAL Derivate-action time constant
floating- by the derivate-
point numbers action time
(unit: sec) constant
(derivative
smoothing).
PID_EQ BOOL PID formula types TRUE: dependent formula
6-467
FALSE: independent formula
TRUE: use the variations in the PV to
calculate the control value of
the derivative (Derivative of the
The calculation of the PID PV).

PID_DE BOOL
derivative error FALSE: use the variations in the error
(E) to calculate the control
value of the derivative
(derivative of the error).
TRUE: forward action; cooling down
(E=PV-SV)
PID_DIR BOOL PID forward/reverse direction
FALSE: reverse action; heating up
(E=SV-PV)
The error value
(E) is the
difference
between the SV
and the PV.
_6 When the
ERR_DBW
setting value is 0,
the function is
disabled;
Range within which the error otherwise the

ERR_DBW DWORD/DINT -32768~32767
value is counted as 0. CPU PLC checks
whether the
present error is
less than the
absolute value of
ERR_DBW, and
checks whether
the present error
meets the cross
status condition.
If the present
6-468
error is less than
the absolute
value of
ERR_DBW,
and meets the
cross status
condition, the
present error is
counted as 0, and
the PLC applies
the PID
algorithm ;
otherwise the
present error is
brought into the

PID algorithm.
Initial value
Integral gain of the 0~100 compensation of

ALPHA DWORD/DINT
initialization value (heating up) Unit: 1% integral calculus
(for heating up)

6_
Initial value
Integral gain of the
0~100 compensation of
BETA DWORD/DINT initialization value (cooling
Unit: 1% integral calculus
down)
(for cooling down)
When set to PID
Manual
(PID_MAN=True),
0~1000 the MV value is
MOUT REAL MV
(unit: 0.1%) outputted as the
value set
manually for
MOUNT.
Feed forward
BIAS REAL Feed forward output value -32768~32767 output value,
used for the PID
6-469
feed forward.
When the
instruction is
scanned, use the

1~1000
CYCLE DWORD/DINT Sampling time (TS) PID algorithm
(unit: 100 ms)
according to the
sampling time,
and refresh MV.
0.0~100.0
MV REAL MV output value MV output value
(unit: 1%)
DWORD/DINT/
PV Present value Format is defined in HWCONFIG.
REAL
Accumulated integral value is for
reference. When the MV is out of the

I_MV REAL Accumulated integral value
range of 0-100%, the accumulated
integral value in I_MV stops changing.
16#0000：instruction is being
_6
executed and is working normally
16#1400：the module you are using

does not support this instruction.
16#1401：group number or module

number setting error
ERROR DWORD/DINT Error codes 16#1402：the module you are using

does not respond and communication
time out
16#1403：channel setting error
16#1404: communication with PID
function is under way, no repeatedly
set ups.
Note:
1. If the PID parameter exceeds the upper limit, only the maximum value can be written in the module, if the PID
parameter is below the lower limit, only the minimum value can be written in the module.
2. When PID_RUN switches from True to False, it clears the MV output value to 0. If you need to keep the last MV
output value, you can switch the operand EN to False to close this instruction and the MV output value can be kept.
6-470
Example
1. You need to set up the parameters before executing DMPID. Switch the operand EN from False to True to execute
this instruction and once the instruction is enabled, the parameters are applied to the modules. If you need to
change parameters during execution, you can use the UPDATE flag to update the parameters (including PID_RUN ~
CYCLE). After the parameters are updated, the system clears the flag UPDATE.
2. When M0 is ON, the instruction is executed. When M2 is ON, the DMPID starts to process. When M2 is OFF, MV
value is 0. And the value in MV is stored in D26. When M0 is OFF, the instruction is not executed. And the values in
the instruction is not changed.
3. When the mode is set to 1, the system starts to auto tuning the parameters for the temperature control. After tuning
is done, the system switches to auto control mode (PID_MODE is set to 0) and fill in the appropriate parameters
(Kc_Kp, Ti_Ki, Td_Kd, Tf, ALPHA and BETA) to data devices. You can also use retentive devices to retain PID
parameters.
6_
6-471
PID formula:
1. When the PID_MODE is set to 0, the mode is set to auto:
 Independent Formula & Derivative of E(PID_EQ=False & PID_DE=False)

t
dE
MV = K P E + Ki ∫ Edt + K d * + BIAS (E = SV – PV or E = PV – SV)
0
dt
 Independent Formula & Derivative of PV(PID_EQ=False & PID_DE=True)
t
dPV
MV = K P E + Ki ∫ Edt − K d * + BIAS (E = SV – PV)
0
dt
Or
t
dPV
MV = K P E + Ki ∫ Edt + K d * + BIAS (E =PV – SV)
0
dt
 Dependent Formula & Derivative of E(PID_EQ=True & PID_DE=False)
 1
t
dE 
MV = K c  E + ∫ Edt + Td *  + BIAS (E = SV – PV or E = PV – SV)
 Ti 0 dt 
 Dependent Formula & Derivative of PV(PID_EQ=True & PID_DE=True)
 1
t
dE 
MV = K c  E + ∫ Edt − Td *  + BIAS (E = SV – PV)
 Ti 0 dt 
Or
 1 dE 
t
MV = K c  E + ∫ Edt + Td *  + BIAS (E = PV – SV)
 Ti 0 dt 
2. When you set the PID_MODE to 1, auto tuning mode is enabled. When auto tuning is complete, the value
_6 becomes 0 and switches off the auto tuning mode automatically.
PID Control Block Diagram:
PID Block Diagram (Independent)

PID_D IR
E
+ 1
SV + DEAD BAND
-
REVERSE
PV 0
X(-1)
ERR_DBW
Kc_Kp
PID-P
>0 PID_MAN
BIAS
+ 0
<=0 +
0 +
Kc_Kp MV_LIMIT
1
MV
Ti_Ki
PID-I
>0
MV_MAX, MV_MIN
+
<=0 +
0 +
Ti_Ki MOUT_AUTO
+ MOUT
0
Td_Kd MOUT
PID-D PID_MAN
>0 1
0
<=0
0 1
Td_Kd, Tf MOUT
6-472
PID Block Diagram (Dependent)

PID_D IR
E
+ 1
SV + DEAD BAND PID-P
-
REVERSE
PV 0
X(-1)
Kc_Kp
ERR_DBW Kc_Kp
>0
<=0
0
PID_MAN
BIAS
+ 0
+
+
MV_LIMIT
1
Ti_Ki MV
PID-I
>0
MV_MAX, M V_MIN
<=0
0
Ti_Ki MOUT_AUTO
MOUT
0
Td_Kd MOUT PID_MAN
PID-D
>0 1
0
<=0
0 1
Td_Kd, Tf MOUT
ERR_DBW
When the PV (present value) is in the range of ERR_DBW, at the beginning, the present error is brought into the
PID algorithm according to the normal processing, and then the CPU module checks whether the present error
meets the cross status condition: PV (present value) goes beyond the SV (target value). Once the condition is met,
the present error is counted as 0 when applying the PID algorithm. After the PV (present value) is out of the
ERR_DBW range, the present error is brought into the PID algorithm again. If PID_DE is true, that means it uses the 6_
variations in the PV to calculate the control value of the derivative, and after the cross status condition is met, the
PLC treats Δ PV as 0 to apply the PID algorithm. (Δ PV= current PV – previous PV). In the following example, the
present error is brought into the PID algorithm according to the normal processing in section A ,and the present error
or Δ PV is counted as 0 to apply the PID algorithm in the section B.
6-473
α, β Value
To reduce overshoot, you can use parameters of ALPHA or BETA in the beginning of the PID operation or while SV
(target value) varies to compensate initial value of integral calculus (for heating up or cooling down). See the images
below. Use ALPHA parameter to reduce overshoot while the temperature is climbing up. Use BETA parameter to
reduce overshoot while the temperature is dropping.
0
Tem perature ( C)
Tim e
_6
0
Temperature ( C)
Time
6-474
Formula of the output cycle:
Set the output cycle width according to the environment. If the environmental temperature changes not so aggressively,
you can set a bigger output cycle width.
 Output cycle width = MV (%) x output cycle
Execute the general pulse with modulation instruction (GPWM) to set output cycle width and output cycle sampling time
to manage the cycle.
Example
If the output cycle is 2000 ms, then the output value is 50% after the PID algorithm is implemented.
 Output cycle width = 50% × 2000 ms = 1000 ms
In other words, the GWPM instruction can be set to output cycle width = 1000 and output cycle = 2000.
t =10 0 0 ms
Ou tp u t Y 1 0
T =2 00 0 ms
Note: 6_
1. When tuning the parameters Kc_Kp, Ti_Ki, and Td_Kd (PID_MODE=0), set the Kc_Kp value first, and then set
the Ti_Ki and Td_Kd values to 0. In a controlled environment, you can increase the values of Ti_Ki (from
smaller to bigger) and Td_Kd (from bigger to smaller). When the value of Kc_Kp is 1, the proportional gain is
100%. That is, the error values increase by a factor of one. When the proportional gain is less than 100%, the
error values decrease. When the proportional gain is greater than 100%, the error values increase.
2. The parameters which have been automatically tuned are not necessarily suitable for every controlled
environment. You can, therefore, further modify the automatically-tuned parameters, but it is recommended
that you only modify the values of Ti_Ki or Td_Kd.
3. The operand CYCLE is to set the sampling time to use the PID algorithm and refresh MV.
4. When the number of the channel for measurement is changed, the time to refresh the measured value also
changes. For example, the measured value is refreshed every 200 ms when there is only 1 channel for
measurement. The measured value is refreshed every 800 ms when there are 4 channels for measurement.
The Kc_Kp, Ti_Ki, Td_Kd parameters may differ when the number of channel for measure is different.
6-475
1418 D HCCNT Module ~ ErrCode HC module counter
Module   
ChNo   
Update    
Action   
Value    
CurCnt  
ST 
MT 
AStat 
RefCnt 
Dir    
CntStat 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
_6 Data type
Module  
ChNo  
Update 
Action  
Value  
CurCnt  
ST  
MT  
AStat  
RefCnt  
Dir 
CntStat  
Error 
ErrCode  

－－ AS
6-476
Symbol
Update ： Parameter updating flag
Action ： Actions for the counter to act
Value ： New counting value / offset value
CurCnt ： Current counter value
ST ： Single-Turn data of an absolute type SSI encoder
MT ： Multi-Turn data of an absolute type SSI encoder
AStat ： Status data of an absolute type SSI encoder
RefCnt ： Refreshing counter of an absolute type SSI encoder
Dir ： Counting direction

CntStat ： Counting status
Error : Error flag

Explanation
1. This instruction is for AS02HC-A only. You can start, stop the counter as well as set up and edit the counter value.
This instruction is available for PLC with FW V1.08.or later and ISPSoft V3.10 or later.
2. Before executing this instruction, you need to set up Action and Value. Once En is triggered, the PLC scans the 6_
values in Action and Value immediately. If you need to edit the values in Action and Value, set new values in Action
and Value and set the Update to ON. Once the values in Action and Value are updated, the Update switches to OFF.
3. Module: The module number that is connected to the right side of PLC directly or connected to the remote module
that acts as PLC, e.g. the first connected module is module number 1, the second connected module is module number
2. Up to 32 modules can be connected and counted and each type of modules should be included in the count.
4. ChNo: Channel number for counter, channel 1 is number 1; channel 2 is number 2.
5. Counter action modes and functions

Action
Function Description
Mode
0 Remain unchanged
Set up a new counter value in Value

Set up / change current counter Note: If you are using SSI (serial synchronous interface) encoder
1 and the setting of counter mode is in Absolute Position, the Action
value (CurCnt)
mode here is invalid.
When the setting of counter mode is in Absolute Position, you can

Set the offset value in SSI set the counter offset value of the SSI encoder. If you set the offset
2
encoder as the value in Value value in Value, the current counter value (CurCnt) is the sum of
the encoder counter value + the value in Value.
6-477
Action
Mode
Note:
1. Range of the value in Value: -2(MT+ST Length-1) ≦ Value<2(MT+ST
Length-1)
. If the value is set out of the range, it is invalid.
2. If you are using SSI (serial synchronous interface) encoder
and the setting of counter type is Ring Counter, the Action
mode here is invalid.
3. After downloading the HWCONFIG settings, the offset value
is cleared to 0.
When the setting of counter mode is in Absolute Position, the
counter value of the SSI encoder will be offset and stored in Value.
If you set the offset value in Value, the current counter value
(CurCnt) is the value in Value. (CurCnt＝Value)
Note:
1. Range of the value in Value: 0 ≦ Value<2 (MT+ST Length). If the
Set / change the absolute
3 value is set out of the range, it is invalid.
position value of the SSI encoder
2. If you are using SSI (serial synchronous interface) encoder
and the setting of counter type is Ring Counter, the Action
mode here is invalid. You can use Action=1 to change the
setting value.
3. After downloading the HWCONFIG settings, the offset value
is cleared to 0.
1. Clear the value in CurCnt to 0.
2. Clear the value in CurNo from DHCCMPT instruction.
3. Clear the flags of Match1 and Match2 from DHCCMPT
Reset the current counter value instruction.
4
(CurCnt) Note: If you are using SSI (serial synchronous interface) encoder
and the setting of counter mode is in Absolute Position, the value
_6
in CurCnt can NOT be cleared to 0 but the value in CurNo, flags
of Match1 and Match2 from DHCCMP instruction can be cleared.
1. Clear the value in CurCnt to 0.
Reset the current counter value 2. Clear the value in CurNo from DHCCMPT instruction.
and the assigned Y output points 3. Clear the flags of Match1 and Match2 from DHCCMPT
5
from DHCCMP and DHCCMPT instruction.
instructions. 4. Clear the assigned Y output points (ONOFF) from
DHCCMP and DHCCMPT instructions.
1. Set the value in CurCnt as the value in Value.
After preset, the DHCCMPT instruction performs the
comparison from the top. If the first value is bigger than the
first value to be compared in the table, the comparison stops.
If this happens, you can use the Update flag (ON) from the
Preset the current counter value
6 DHCCMPT instruction to perform comparison again.
(CurCnt)
instruction.
Note: If you are using SSI (serial synchronous interface) encoder
and the setting of counter mode is in Absolute Position, the value
in CurCnt can NOT be changed but the value in CurNo, flags of
Match1 and Match2 from DHCCMP instruction can be cleared.
1. Set the value in CurCnt as the value in Value.
Preset the current counter value
and clear the assigned Y output
7 After preset, the DHCCMPT instruction performs the
points from DHCCMP and
comparison from the top. If the first value is bigger than the
DHCCMPT instructions.
first value to be compared in the table, the comparison stops.
6-478
Action
Mode
If this happens, you can use the Update flag (ON) from the
DHCCMPT instruction to perform comparison again.
instruction.
4. Clear the assigned Y output points (ONOFF) from
DHCCMP and DHCCMPT instructions.
6. CurCnt: The current counter value of the appointed module channel.
7. ST: Single-Turn data of an absolute type SSI encoder. If the counter mode is in absolute position, the value of ST is
an offset value. For the Ring counter, the value of ST is an original SSI figure. For an incremental encoder, the value
of ST is 0.
8. MT: Multi-turn data of an absolute type SSI encoder. If the counter mode is in absolute position, the value of MT is an
offset value. For the Ring counter, the value of MT is an original SSI figure. For an incremental encoder, the value of
MT is 0.
9. AStat: Status data of an absolute type SSI encoder. For an incremental encoder, the value of AStat is 0.
10. RefCnt: Refreshing counter of an absolute type SSI encoder, within a maximum range of 16-bit. When one SSI data
is captured, add one to the value of RefCnt. Once an overflow occurs, the refreshing counter starts counting from 0.
For an incremental encoder, the value of RefCnt is 0.
11. Dir: Counting direction, when the value is ON, it goes in the positive direction; when the value is OFF, it goes in the
negative direction.
12. CntStat: Counting status

Bit number Status Description Remarks
15 ~ 11 Reserved Reserved 6_
In HWCONFIG you can set the option to detect or not to
detect if the absolute position crossing zero point. (default:
detection disabled)
SSI absolute If the counter mode is in Absolute Position and you have set
positon the offset, the detection starts after the value is offset.
0: normal
10 encoder If the counter type is Ring Counter, the offset value will be
1: abnormal
experiencing reset to zero. The detection starts at the initial position of the
zero crossing SSI.
Cause of the error: zero crossing
Ways to clear the error: use the DHCCNT instruction to
reset/preset or execute RESET by the external input point
Cause of the error: abnormal communication for 5 times in a
SSI
0: normal row
9 communication
1: abnormal Ways to clear the error: the communication comes back to
check
normal
SSI parity 0: normal Cause of the error: parity check failed

8
check 1: abnormal Ways to clear the error: the next parity check pass
SSI data Cause of the error: SSI data exceeding the set acceptable
exceeding the 0: normal range
7
set acceptable 1: abnormal Ways to clear the error: when the SSI data stops exceeding
range the set acceptable range
6-479
Bit number Status Description Remarks
6 Reserved Reserved
Ring counter - 0: normal In HWCONFIG you can set the option to detect or not to
5 detect. (default: detection disabled)
Overflow 1: abnormal
Cause of the error: when either overflow (>231 − 1) or
underflow (<-231 )
Ring counter - 0: normal
4
Underflow 1: abnormal Ways to clear the error: use the DHCCNT instruction to
Linear counter Cause of the error: the value of the linear counter exceeds
– the value 0: normal the user-defined range
3
exceeds the 1: abnormal Ways to clear the error: when the value of the linear counter
upper limit is within the user-defined range
Linear counter
Note: when the counting value exceeds the upper or lower
– the value 0: normal
2 limit, the value will keep as the value in upper/lower limit.
exceeds the 1: abnormal
After the values return to the acceptable range, the counting
lower limit
continues.
Cause of the error: even if the value of the linear counter
Linear counter 0: normal exceeds the user-defined range, the hardware counter
1
- Overflow 1: abnormal continues counting. But if the hardware counter counting is
either overflow (>231 − 1) or underflow (<-231 ), the counting
stops. After clearing the error, the counting resumes.
Linear counter 0: normal
0
- Underflow 1: abnormal Ways to clear the error: use the DHCCNT instruction to
13. If you stopped executing the instruction, the channel values will stop updating.
14. Refer to the following table for more details when any of the Error flag is ON.
_6
ErrCode Description
16#1400 This function is NOT available for this module.
16#1401 The value is invalid or out of range.
16#1402 No response from the module. Communication timeout.
16#1403 HWCONFIG configuration error. Instruction stops.
16#1404 There is no such counting channel for the HC module.
16#1405 Input interface not selected. Instruction stops.
16#1406 Invalid value in Action
One of the counting channel of the HC module is executing counting. Other channels cannot
16#1410
perform the same task at the same time.
6-480
Example 1: Setting / changing the current setting (Action = 1)
1. Set M0=ON, the counter starts counting.
2. In DHCCNT instruction, set the value in Action to 1 and the value in Value to 10000. When the update flag M1 is
ON, the value in CurNo is updated to 10000.
3. After execution, the update flag M1 clears to OFF automatically.
Counter value
10000
Action 1
Value 10000
6_
Update flag
6-481
Example 2: Set the offset value in SSI encoder as the value in Value (Action = 2)
1. In HWCONFIG, set the channel 1 as SSI input and set the counter mode to absolute position.
3. In DHCCNT instruction, set the value in Action to 2 and the value in Value to 500. Supposing the current counting
value (CurNo) is 2500, and when the update flag M1 is ON, the value in CurNo is updated to 3000.
Original positon of the

SSI encoder
(ST+M T Len gth)
2
Counter value N
Action 2
_6 Value N
Update flag
6-482
Example 3: Set / change the absolute position value of the SSI encoder (Action = 3)
1. In HWCONFIG, set the channel 1 as SSI input and set the counter mode to absolute position.
3. In DHCCNT instruction, set the value in Action to 3 and the value in Value to 0. When the update flag M1 is ON, the
HC module counters the offset value automatically and the value in CurNo is offset to 0.
original position of the

SSI encoder
(ST+M T Len gth)
2
Counter value
Action 3
6_
Value 0
Update flag
6-483
Example 4: Reset / preset the current counter value (Action = 4, 6)
2. In DHCCNT instruction, set the value in Action to 4. When the update flag M1 is ON, the value in CurNo is reset to
3. In DHCCNT instruction, set the value in Action to 6 and the value in Value to 10000. When the update flag M1 is
ON, the value in CurNo is preset to 10000. After execution, the update flag M1 clears to OFF automatically.
Counter value
10000
Preset
0 Reset
Action 4 6
_6 Value 10000
Match1, Match2,
CurNo
Update flag
6-484
1419 D HCCAP Module ~ ErrCode HC module counter value captured
Module   
ChNo   
TrgSel   
Capt1  
Cmplt1    
Capt2  
Cmplt2    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
ChNo  
TrgSel  
Capt1  
Cmplt1 
Capt2   6_
Cmplt2 
Error 
ErrCode  

－－ AS
Symbol
Module ： Module number
ChNo ： Channel number
TrgSel ： Trigger selection
Capt1 ： Capture value 1
Cmplt1 ： Capture value 1 compete
Capt2 ： Capture value 2
Cmplt2 ： Capture value 2 compete
Error ： Error flag
ErrCode ： Error code
6-485
Explanation
2. Use this instruction with DHCCNT instruction. When executing DHCCNT instruction, the counting starts. And you can
use DHCCAP to capture the counter value. When DHCCNT stopped, the counter value stops updating. And the
captured value stays the same.
3. Before executing this instruction, you need to set up TrgSel. Once En is activated, the PLC scans the values in TrgSel
immediately. If you need to edit the values in TrgSel, set new values in TrgSel and stop the instruction and then
execute the instruction again.
6. TrgSel: Trigger modes and functions
TrgSel Function Description
Triggered by the digital input You need to set the setting value in Z-Phase function of the appointed
0 points of the appointed channel to Capture in HWCONFIG to work with this trigger mode.
_6 channel
Supposing you execute DHCCAP instruction on channel 2 and set
TrgSel = 1, and use channel 1 for the execution of DHCCMP. When

Triggered by the other Match 1/ Match 2 is OFF  ON on channel 1, the channel 2 is
channel’s comparing output triggered to capture the current value and stores it in Capt 1 or Capt 2.
1
instruction (Match1 / Match 2
Note: Even if you have set the setting value in Z-Phase function of the
of DHCCMP instruction)
appointed channel to Capture in HWCONFIG, when TrgSel = 1, this
capture function of external input point is invalid.
7. Capture the current counter value and store it in Capt 1 or Capt 2. When TrgSel = 0, it captures the counter value
when the external input point is rising-edge triggered and stores the value in Capt1 and it captures the counter value
when the external input point is falling-edge triggered and stores the value in Capt2. When TrgSel = 1, it captures the
counter value when Match 1 is OFF  ON in the other channel and store the captured value in Capt1 it captures the
counter value when Match 2 is OFF  ON in the other channel and store the captured value in Capt2.
8. Flags of Cmplt1 and Cmplt2 are indicators to see if the captures in Capt1 and Capt2 are complete. When
Cmplt1/Cmplt2 is OFF  ON , it indicates the values in Cmplt1/Cmplt2 are updated. You can clear the flag to OFF.
Even if you did not clear the Cmplt flags to OFF, the captured values can still be updated.
6-486
9. If En ON  OFF, it indicates the capture function is disabled. The values in Capt1 and Capt2 will not be updated. The
flags of Cmplt1 and Cmplt2 will be cleared off.
ErrCode Description
16#1407 Invalid value in TrgSel
One of the counting channel of the HC module is executing capturing. Other channels cannot
16#1411
Example 1: Capture the counter value when the external input point is triggered.
1. You need to set the setting value in Z-Phase function of the Channel 1 to Capture in HWCONFIG to work with this
trigger mode. 6_
2. Set the value in TrgSel to 0 for DHCCAP instruction. When M0 = ON, DHCCAP instruction starts to wait for the
external input point to be rising-edge or falling-edge triggered.
3. When the external input point of channel 1 is rising-edge triggered, it captures the counter value 1800 and stores the
value in Capt1. And the flag of Cmplt1 is OFF  ON.
4. When the external input point of channel 1 is falling-edge triggered, it captures the counter value 6000 and stores
the value in Capt2. And the flag of Cmplt2 is OFF  ON.
5. The Cmplt flag is not cleared to OFF. New captured value is still updated in Capt1 and Capt2. Here you can see the
new captured value 8500 is updated in Capt1.
6. The external input point of channel 1 is falling-edge triggered again, it captures the counter value 11000 and stores
6-487
TrgSel = 0
11000
Channel 1 8500
Counter
Value 6000
_6 1800
CH1 Z-Phase
Input
Capt1 1800 8500
Cmplt1
*1
CH1
Capt2 6000 11000
Cmplt2
*2
* 1: Cmplt 1 is not cleared to OFF, the captured value still updates in Capt 1.
*2: Cmplt 2 is cleared to OFF, the captured value still updates in Capt 2.
6-488
Example 2: Capture the counter value by executing DHCCMP instruction and when Match 1/ Match 2 is OFF  ON in
the other channel.
1. Supposing you execute DHCCAP instruction on channel 2 and set TrgSel = 1, and use channel 1 for the execution of
DHCCMP. When Match 1/ Match 2 is OFF  ON on channel 1, the channel 2 is triggered to capture the current value
and stores it in Capt 1 or Capt 2. Even if you have set the setting value in Z-Phase function of the appointed channel
to Capture in HWCONFIG, when TrgSel = 1, this capture function of external input point is invalid.
2. The Comp 1 (Match 1) is OFF  ON on channel 2, new captured value 2000 on channel 1 is updated in Capt1 and
Cmplt 1 is OFF  ON.
3. The Comp 2 (Match 2) is OFF  ON on channel 2, new captured value 8000 on channel 1 is updated in Capt2 and
Cmplt 2 is OFF  ON.
4. The Cmplt flag is not cleared to OFF. New captured value is still updated in Capt1 and Capt2.
5. The external input point of channel 1 is falling-edge triggered again, it captures the counter value 11000 and stores
6_
6-489
TrgSel = 1
Channel 1 8000
Counter
_6 Value
2000
MATCH 2 is OFF to ON
CH2 Comp2 on channel 2.
Channel 2
Counter CH2 Comp1
Value MATCH 1 is OFF to ON
on channel 2.
0
Capt1 2000
Cmplt1
CH1
Capt2 8000
Cmplt2
6-490
1420 HCDO Module ~ ErrCode HC module digital output point
Module   
DOdata   
DOstat 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
Update 
DOdata  
DOstat  
Error 
ErrCode  

－ AS －
Symbol 6_
Update ： Channel number
DOdata ： Digital output data
DOstat ： Digital output state
Explanation
2. Before executing this instruction, you need to set up DOdata. Once En is activated, the PLC scans the values in
DOdata immediately. DOdata is the initial status of the output points Y0.0 ~ Y0.3. If you need to change the status of
the output point, you need to set new values in DOdata and set the Update to ON. Once the values in DOdata is
updated, the Update switches to OFF.
6-491
4. DOdata: setting for the action of the output points
b15~b4 b3 b2 b1 b0
NA Action of Y0.3 Action of Y0.2 Action of Y0.1 Action of Y0.0
0：OFF
NA
1：ON
5. DOstat: setting for the state of the output points
b15~b4 b3 b2 b1 b0
NA State of Y0.3 State of Y0.2 State of Y0.1 State of Y0.0
0：OFF
NA
1：ON
6. DOstat: If you stopped executing the instruction, DOstat will stop updating.
ErrCode Description
_6 16#1403 HWCONFIG configuration error. Instruction stops.
One of the output point of the HC module is executing output. Other channels cannot perform
16#1411
the same task at the same time. (DOstat can still be updated.)
8. When the instructions DHCCMP or DHCCMPT are being executed, you cannot change the output points via DOdata
but DOstat can keep updating.
9. To set up the initial values for the output points of DHCCMP, you can start HCDO instruction first and then DHCCMP
or DHCCMPT instruction. If you need to change the output points, you can stop DHCCMP or DHCCMPT instruction
and then use DOdata of HCDO to update the actions of the output points.
6-492

HC module counter value in comparison
1421 D HCCMP Module ~ ErrCode
for output
Device X Y M S T C HC D FR SM SR E K 16# “$” F I
Module   
ChNo   
Comp1    
Action1   
Yno1   
Comp2    
Action2   
Yno2   
Match1     
Match2     
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Module  
6_
ChNo  
Update 
Comp1  
Action1  
Yno1  
Comp2  
Action2  
Yno2  
Match1 
Match2 
Error 
ErrCode  

－－ AS
6-493
Symbol

Comp1 ： Compared value 1
Action1 ： Actions to take when the Comp1 is ON
Yno1 ： Number of output point to output when the Comp1 is ON
Comp2 ： Compared value 2

Action2 ： Actions to take when the Comp2 is ON
Yno2 ： Number of output point to output when the Comp2 is ON
Match1 ： When the value reaches the set value 1, this flag is ON.
Match2 ： When the value reaches the set value 2, this flag is ON.
Explanation
1. This instruction is for AS02HC-A only. The counter value either by counting up or counting down met the set value is
a MATCH. Once you have a MATCH, the system reacts accordingly to what you have set, including counter actions
and which output point to output. This instruction is available for PLC with FW V1.08.or later and ISPSoft V3.10 or
later.
_6
2. Use this instruction with DHCCNT instruction. When executing DHCCNT instruction, the counting starts. And then you
can use DHCCMP instruction to do the comparison.
3. Before executing this instruction, you need to set up Comp1, Comp2, Action1, Action2, Yno1, and Yno2. Once En
is activated, the PLC scans the values in Comp1, Comp2, Action1, Action2, Yno1, and Yno2 immediately.
4. You can edit the values in Comp1, Comp2, Action1, Action2, Yno1, and Yno2 during operation. Set new values and
set the Update to ON. Once the values are updated, the Update, Match1 and Match2 switch to OFF.
7. Comp 1and Comp 2 are the values for comparison (The value in Comp 1 and Comp 2 should be different.). If the
counter value of ChNo met the set value, its corresponding flag Match 1 / Match2 will be ON. The appointed output
point by Yno1 and Yno2 reacts according to the settings for Action.
6-494
8. When the counter type is linear, the value in Comp 1 and Comp 2 should satisfy the following condition: the smallest
counter value < Comp < the largest counter value. If you are using SSI (serial synchronous interface) encoder and
the setting of counter mode is in Absolute Position. The value in Comp 1 and Comp 2 should satisfy the following
condition: 0< Comp<2 (MT+ST Length).
9. The timing to be considered reaching the set value varies according to different settings on input interfaces in
HWCONFIG, for example pulse input and SSI input.
Ex. Comp = 5
8
7 7
Counting up 6 Counting down
6
Comp
5 5
4 4
3 3
2 2
1 1
0 0
Counted Value
0 1 2 3 4 5 6 7 8 9 7 6 5 4 3 2 1 0
Pulse Input -
Timing to consider as reaching the target
SSI Input -
If the input interface is pulse input, the timing to be considered to meet the set value is before the counting leaving
the set value. Take Comp = 5 as an example, when the counting goes from 5 to 6 or from 5 to 4, the timing here is
considered the set value reached. 6_

If the input interface is SSI input, the timing to be considered reaching the set value is right before the counting
touching the set value. Take Comp = 5 as an example, when the counting goes from 4 to 5 or from 6 to 5, the timing
here is considered the set value reached.
10. If the counter value of ChNo met the set value, its corresponding flag Match 1 / Match2 will be ON. The appointed
output point by Yno1 and Yno2 reacts according to the settings for Actions: Action 1 (for the appointed output point
by Yno1) and Action 2 (for the appointed output point by Yno2).
Action 1 Description Action 2 Description Remarks
0 No action 0 No action
1 OFF 1 OFF
2 ON 2 ON
3 Toggle between ON /OFF 3 Toggle between ON /OFF
OFF + clear the counter value of OFF + clear the counter value When the counter
4 4
its channel of its channel value is cleared,
ON + clear the counter value of ON + clear the counter value of the flags of Match
5 5
its channel its channel 1 and Match 2
6-495
Toggle between ON /OFF + Toggle between ON /OFF + will also be
6 clear the counter value of its 6 clear the counter value of its cleared.
channel channel
Clear the counter value of its Clear the counter value of its
7 7
channel channel
Clear the counter value of its Clear the counter value of its
channel + OFF (appointed channel + OFF (appointed

8 8
output points by both Yno1 & output points by both Yno1 &
Yno2) Yno2)
Note: there is a time difference between meeting the set value and for the action to take place. Up to 100 us of time
difference can be expected.
11. Set the value in Yno1 and Yno2 to assign the output points Y0.0, Y0.1, Y0.2, and Y0.3. You can have two sets of
values (Yno1 and Yno2) to achieve two sets of comparisons. After this instruction starts to execute, you cannot use
HCDO instruction to control the output points.
Yno1/Yno2 Appointed output points
0 Y0.0
1 Y0.1
2 Y0.2
3 Y0.3
_6
12. The counter value either by counting up or counting down met the set value is a MATCH. The flags of Match 1 and
Match 2 are the indicators. When the counter value met the set value, its corresponding Match 1 or Match 2 flag will
be ON. Either one of the followings occurs, the flags of Match 1 and Match 2 will be cleared to OFF, when the PLC
CPU stops, clears the counters, DHCCMP instruction switches from OFF to ON, or Update flag is set to ON.
13. The flags of Match 1 and Match 2 can be used for interrupt devices I, ranging from I400 to I431.
Note: The frequency of the interrupt device I with the same numbering should not be higher than 800Hz.
14. If you stopped executing the instruction, its relative compared values and its output function will stop updating.
ErrCode Description
6-496
ErrCode Description
16#1409 Invalid value in Yno
One of the counting channel of the HC module is executing output. Other channels cannot
16#1413
Example 1: Output from the output point Y when the counter value reached the set value.
1. In HWCONFIG set the input interface of the channel 1 to pulse input or SSI input. And set the counter type to ring
counter.
2. Set the value in Comp 1 to 16#5000000, the value in Action1 to 3, and the value in Yno1 to 0; set the value in
Comp 2 to 16#D000000, the value in Action2 to 3, and the value in Yno2 to 1.
3. When M0 = ON, the counter starts counting and sets parameters for DHCCMP instruction and then waits for the
6_
counter value to meet the set value.
4. When the counter value reached Comp 1, the Match 1 flag is ON. Y0.0 is OFFON.
6. When the counter value reached Comp 1 once again, the Match 1 flag is ON. Y0.0 is OFFON.
6-497
H’7FFFFFFF
Comp1
Channel 1
Counter 0
Value
_6 Comp2
H’80000000
MATCH1
Y0.0
MATCH2
Y0.1
6-498
Example 2: Clear the counter value of its channel when the counter value reached the set value.
1. Set the value in Comp 1 to 2500, the value in Action1 to 2, and the value in Yno1 to 0; set the value in Comp 2 to
5000, the value in Action2 to 8, and the value in Yno2 to 1.
4. When the counter value reached Comp 2, start the Action 2 = 8: clear the counter value of its channel, clear the
flags of Match 1 / Match 2 and Y0.0 / Y0.1 to OFF.
6_
Comp2
Comp1
Channel One
Counter 0
Value
MATCH1
Y0.0
MATCH2
Y0.1
6-499
Example 3: Update the counter value of its channel when the counter value reached the set value.
4. When the counter value reached Comp 2, the Match 2 flag is ON. Y0.1 is ONOFF.
5. Set a new value for comparison. Set the value in Comp 1 to 15000, the value in Action1 to 3, and the value in Yno1
to 0; set the value in Comp 2 to 20000, the value in Action2 to 6, and the value in Yno2 to 1.
6. Set the Update flag to ON. Once the update is done, the flag is cleared to OFF automatically and the flags of Match
1 / Match 2 will also be cleared.
7. When the counter value reached Comp 1 once again. Y0.0 is ONOFF.
8. When the counter value reached Comp 2 once again. Y0.1 is ONOFF and start the Action 2 = 6: Toggle between
ON /OFF, clear the counter value of its channel, and the flags of Match 1 / Match 2 will also be cleared.
New Comp2
New Comp1
Comp2
_6 Channel 1 Comp1
Counter 0
Value
Update Flag
MATCH1
Y0.0
MATCH2
Y0.1
6-500
Example 4: Execute interrupts when the counter value reached the set value.
1. DHCCMP instruction can be used for interrupt. Set the flags of Match 1 and Match 2 as interrupts of I400 and I401
respectively.
4. When the counter value reached Comp 1, I400 interrupt is executed and start the Action 1 = 3: Y0.0 toggles
between ON /OFF.
5. When the counter value reached Comp 2, I401 interrupt is executed and start the Action 2 = 3: Y0.1 toggles
between ON /OFF.
6_
6-501

HC module counter value in group
1422 D HCCMPT Module ~ ErrCode
comparison for output
Module   
ChNo   
CmpLen   
CompS  
ActionS 
YnoS 
InoS 
CurNo 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Device
Module  
ChNo  
_6 Update 
CmpLen  
CompS  
ActionS  
YnoS  
InoS  
CurNo  
Error 
ErrCode  

－－ AS
6-502
Symbol


CmpLen ： Data length for comparison
CmpS ： Compared value (32-bit)
ActionS ： Actions to take when the CmpS is ON
YnoS ： Number of output point to output when the CmpS is ON
InoS ： Number of interrupt to be executed when the CmpS is ON
CurNo ： Current group number for comparison

Explanation
1. This instruction is for AS02HC-A only. It is used for comparing the counter value in a cyclic manner and once the value
is matched, the set action is taken. When the last group is done for comparison, set the counter value as the first
compared value and the comparison goes back to the first group.
2. This instruction can only work for one direction. If you change the direction in the middle of instruction execution, the
result may be incorrect. Up to 10 compared values can be set. You need to arrange the values (should be non-identical)
in order, either ascending or descending. When in ascending order, the counting method is count-up and the values 6_
used should be positive integer numbers. When in descending order, the counting method is count-down and the
values used should be negative integer numbers. When the counter value matched the compared value, the output
points or the counter react according to your settings.
3. This instruction is available for PLC with FW V1.08.or later and ISPSoft V3.10 or later.
can use DHCCMPT instruction to do the comparison.
5. Before executing this instruction, you need to set up CmpLen, CompS, ActionS, YnoS and InoS. Once En is
activated, the PLC scans the values in CmpLen, CompS, ActionS, YnoS and InoS immediately.
6. You can edit the values in CmpLen, CompS, ActionS, YnoS and InoS during operation. Set new values and set the
Update to ON. Once the values are updated, the flag of Update switches to OFF automatically.
9. CmpLen: the data length for comparison in a cycle; the setting range is 2~10. When the setting value is out of the
6-503
range, the system cannot execute the instruction and an error code appears.
10. CmpS is where you store the values (in 32-bit integer format) for comparison. It takes several space of Dword in
CmpLen consecutively. You need to arrange the values (should be non-identical) in order, either ascending or
descending. When in ascending order, the counting method is count-up and the values used should be positive integer
numbers. When in descending order, the counting method is count-down and the values used should be negative
integer numbers. It is suggested to use array of Dword to declare.
When the counter type is linear, the value in CmpS should satisfy the following condition: the smallest counter value
< CmpS < the largest counter value.
If you are using SSI (serial synchronous interface) encoder and the setting of counter mode is in Absolute Position.
The value in CmpS should satisfy the following condition: 0< CmpS<2 (MT+ST Length).
11. The timing to be considered reaching the set value varies according to different settings on input interfaces in
HWCONFIG, for example pulse input and SSI input.
Ex. Comp = 5
8
7 7
Counting up 6 Counting down
6
Comp
5 5
4 4
3 3
2 2
1 1
0 0
_6 Counted Value
0 1 2 3 4 5 6 7 8 9 7 6 5 4 3 2 1 0
Pulse Input -
SSI Input -
If the input interface is pulse input, the timing to be considered to meet the set value is before the counting leaving the
set value. Take Comp = 5 as an example, when the counting goes from 5 to 6 or from 5 to 4, the timing here is
considered the set value reached.
If the input interface is SSI input, the timing to be considered reaching the set value is right before the counting touching
the set value. Take Comp = 5 as an example, when the counting goes from 4 to 5 or from 6 to 5, the timing here is
considered the set value reached.
12. If the counter value of ChNo met the set value, the appointed output point by YnoS reacts according to the settings
for ActionS. The value in ActionS should be a 16-bit integer and takes several space of Word in CmpLen
consecutively.
6-504
Action Description Remarks
0 No action
1 OFF
2 ON
3 Toggle between ON /OFF
4 OFF + clear the counter value of its channel
5 ON + clear the counter value of its channel

When the counter value is cleared, the value
Toggle between ON /OFF + clear the counter value
6 in CurNo is also cleared to zero.
of its channel
7 Clear the counter value of its channel
Clear the counter value of its channel + OFF

8
(appointed all output points by both YnoS)
Note: there is a time difference between meeting the set value and for the action to take place. Up to 100 us of time
difference can be expected.
13. The value in YnoS should be a 16-bit integer and takes several space of Word in CmpLen consecutively.
YnoS Appointed output points
0 Y0.0
1 Y0.1
2 Y0.2
6_
3 Y0.3
14. The value in InoS is the interrupt numbers. You can send specific interrupts to the PLC CPU. The allowable interrupt
is ranging from I400 to I431. The value in InoS should be a 16-bit integer and would take several space of Word in
CmpLen consecutively.
InoS Action
0 No interrupt
 = 00~31; corresponding to I400~I431

4
(When the set value is met, the specific interrupt is requested by a PLC CPU.)
Note: The frequency of the interrupt device I with the same numbering should not be higher than 800Hz.
15. CurNo is the current group number. See the table below for reference. If the counter value is 200, the counted number
is less than the value in D100, and the matched CurNo is 0. If the counter value is 1000, check the table below to find
the value in D100 is also 1000 and the matched CurNo is 1.
6-505
16. CmpS (supposing D100), ActionS (supposing D200), YnoS (supposing D300), and the value in CmpLen is 6.
CmpS ActionS YnoS

InoS
CurNo Source value for To take when the (output point
(interrupt number)
comparison (32-bit) value is met number)
1 D100 = 1000 D200 = 2 (On) D300 = 0 (Y0.0) D400 = 400 (I400)
2 D102 = 2000 D201 = 2 (On) D301 = 1 (Y0.1) D401 = 401 (I401)
3 D104 = 3000 D202 = 3 (Toggle) D302 = 0 (Y0.0) D402 = 402 (I402)
4 D106 = 4500 D203 = 2 (On) D303 = 2 (Y0.2) D403 = 403 (I403)
5 D108 = 5500 D204 = 1 (Off) D304 = 3 (Y0.3) D404 = 404 (I404)
6 D110 = 6500 D205 = 1 (Off) D305 = 1 (Y0.1) D405 = 405 (I405)
17. Executing the instruction (En OFF  ON) and set the Update to ON. Once the values are updated, the instruction
uses the updated values for comparison. The current number less than the corresponding value in CmpS is set for
comparison. For instance, if the current value is 3500 when the instruction is executed, the corresponding CurNo is 3
and the number 1~3 (counter value 3000 < current value 3500) are set for comparison. The action set is Y0.0 = ON +
interrupt I400 request, Y0.1 = ON + interrupt I401 request, Y0.0 = toggle between ON and OFF) + interrupt I402
request, and the value in CurNo is 3.
18. If En ON  OFF, it indicates the comparison output function is disabled. The states of CurNo and Output stop
updating. The counter continues to count but no comparison is made.
_6
ErrCode Description
16#1408 Incorrect order in the value of CmpS
16#1409 Invalid value in Yno
6-506
ErrCode Description
16#140C Invalid value in CmpLen
One of the counting channel of the HC module is executing output. Other channels cannot perform
16#1413
the same task at the same time.
16#1416 Invalid value in InoS
Example 1
1. Set up the following parameters.
CmpS ActionS YnoS

InoS
CurNo Source value for To take when the (output point
(interrupt number)
comparison (32-bit) value is met number)
1 D50 = 1000 D70 = 3 (Toggle) D80 = 0 (Y0.0) D90 = 400
2 D52 = 2000 D71 = 3 (Toggle) D81 = 1 (Y0.1) D91 = 401
3 D54 = 3000 D72 = 3 (Toggle) D82 = 2 (Y0.2) D92 = 402
4 D56 = 4000 D73 = 3 (Toggle) D83 = 3 (Y0.3) D93 = 403
5 D58 = 5000 D74 = 3 (Toggle) D84 = 0 (Y0.0) D94 = 404
6 D60 = 6000 D75 = 3 (Toggle) D85 = 1 (Y0.1) D95 = 405
7 D62 = 7000 D76 = 3 (Toggle) D86 = 2 (Y0.2) D96 = 406 6_

8 D64 = 8000 D77 = 3 (Toggle) D87 = 3 (Y0.3) D97 = 407
9 D66 = 9000 D78 = 3 (Toggle) D88 = 0 (Y0.0) D98 = 408
10 D68 = 10000 D79 = 3 (Toggle) D89 = 1 (Y0.1) D99 = 409
2. Executing the instruction (En OFF  ON) and set the Update to ON. Once the values are updated, the instruction
uses the updated values for comparison. The current counted number less than the corresponding value in CmpS is
set for comparison. The starting current value is less than 1000, its corresponding CurNo is 0 and no action is taken.
3. When the counter value met 1000 (999→1000), its corresponding CurNo switches from 0 to 1 and Y0.0 switches
from OFF to ON, and I400 interrupt is executed. If the input interface is pulse, the comparison begins when the
counter value is reaching 1001 (1000→1001).
6-507
6. Follow the same rule to do the comparison, until the CurNo is 10. After the last comparison is done, set the counter
value to 1000 so that the CurNo can go back to 1.
7. If you are using the ring counter, when the counter value met 10000 again, the comparison starts again. The CurNo
is 1, Y0.0 switches from OFF to ON, and I400 interrupt is executed. And follow the same rule to do the comparison.
_6
6-508
10000
9000
8000
7000
6000
5000
4000
3000
2000
1000
Channel 1
Counter 0
Value
EN
CurNo 0 1 2 3 4 5 6 7 8 9 10 10 1 2
Y0.0
Y0.1
Y0.2
Y0.3
6_
6-509

HC module measurements of frequency
1423 D HCMEAS Module ~ ErrCode
and revolution
Module   
ChNo   
Cnt/Rev   
Smpl   
Avg   
Freq 
RPM 
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Device
Module  
ChNo  
Update 
Cnt/Rev  
_6 Smpl  
Avg  
Freq  
RPM  
Error 
ErrCode  

－－ AS
Symbol

Cnt/Rev ： Counted value of the encoder revolution for one time
Smpl ： Sampling cycle
Avg ： Average times
Freq ： Measured frequency
RPM ： Measured revolutions per minute (rpm)
6-510
Explanation
1. This instruction is for AS02HC-A only. This instruction is available for PLC with FW V1.08.or later and ISPSoft V3.10
or later.
can use DHCCMP instruction to do the comparison.
3. Before executing this instruction, you need to set up Cnt/Rev, Smpl and Avg. Once En is activated, the PLC scans
the values in Cnt/Rev, Smpl and Avg immediately.
4. You can edit the values in Cnt/Rev, Smpl and Avg during operation. Set new values and set the Update to ON. Once
the values are updated, the Update flag switches to OFF.
7. Cnt/Rev: Counted value of the encoder revolution for one time, ranging from 1 to 4294967295
(H’00000001~H’FFFFFFFF).
8. Smpl: Sampling cycle, ranging from 1 to 1000, unit: ms. Different values set in Smpl and Freq for output and RPM
for output may cause different resolutions. 6_

Resolution of Frequency = 1000 ÷ Smpl (unit: Hz)
Cnt
Resolution of RPM = 60000 ÷ �Smpl × � (unit: rev/min)
Rev
The start of sampling cycle and the current counted number (CurCnt) are two basic components for the calculation of
revolution. Therefore you need to take the following factors that may affect the measurement results into account.
Encoder Type Counter Type Factors that affect the measurement results
The difference between the counted values in the same sampling

Ring counter
cycle exceeds the limit of 231.
Incremental Encoder The difference between the counted values in the same sampling
Linear counter cycle exceeds the limit of 231 or the counted value exceeds the
upper/lower limit.
Absolute The difference between the counted values in the same sampling
（MT+ST Length）-1
SSI encoder Positon cycle exceeds the limit of 2 .
In Absolute Positon The difference between the counted values in the same sampling
Ring Counter
cycle exceeds the limit of 231.
6-511
9. Avg is the average times and in the moving average of the measurement result, ranging from 1 to 10.
10. Freq is the measurement result of the average frequency; unit: Hz. The format is as below.
CurCnt(t + 𝐒𝐒𝐒𝐒𝐒𝐒𝐒𝐒) − CurCnt(t)

Freqency (Hz) =
𝐒𝐒𝐒𝐒𝐒𝐒𝐒𝐒(ms) × 10−3
11. RPM is the measurement result of the average revolution; unit: rev/min. The format is as below.
( CurCnt(t + 𝐒𝐒𝐒𝐒𝐒𝐒𝐒𝐒) − CurCnt(t) ) × 60

Revolution (rev/min) =
𝐂𝐂𝐂𝐂𝐂𝐂/𝐑𝐑𝐑𝐑𝐑𝐑 × 𝐒𝐒𝐒𝐒𝐒𝐒𝐒𝐒(ms) × 10−3
12. If you stopped executing the instruction, its measuring function will stop. The values in Freq and RPM will not be
updated.
13. Note that if you clear or change the counter value, the sampling measurement result of Freq and RPM in the cycle
will be affected.
ErrCode Description
_6 16#1403 HWCONFIG configuration error. Instruction stops.
16#140A Measured frequency is out of range.
16#140B Measured revolutions per minute (rpm) is out of range.
16#140D Invalid value in Smpl
16#140E Invalid value in Avg
16#140F Invalid value in Cnt/Rev
One of the counting channel of the HC module is executing frequency measuring. Other
16#1415
channels cannot perform the same task at the same time.
6-512

Read the parameter from the O-Link
1426 IOLINKR Execute ~ DataRead
device
Group   
Module   
Port   
Index   
SubIndex   
DataType   
Done    
Error    
ErrCode 
ReadLen 
DataRead 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
DINT
LINT
TMR
CNT
INT
Device
Group  
Module  
Port   6_
Index  
SubIndex  
DataType  
Busy 
Done 
Error 
ErrCode  
ReadLen  
DataRead  

－ AS －
6-513
Symbol
Port ： Communication port number
Index ： Index number of the parameter
SubIndex ： Subindex number of the parameter
DataType ： Data type
ReadLen ： The length of the read data
DataRead ： Data that is read
Done ： Communication complete
Explanation
2. You can refer to the IODD file of the IO-Link device to learn more about the device parameters. You can also use this
instruction to read the IO-Link device parameters.
3. There is no limit on the number of times you execute the instruction but only one instruction (IOLINKR or IOLINKW)
can be executed at a time.

_6 4. During communication, it takes at least 5 seconds for the IO-Link device to response. Do NOT stop or start another
instruction during this time. After the communication with IO-Link is done, it is suggested to use the flags DONE or
ERROR to stop or start the instruction.
5. Group: The group number of AS04SIL that is connected to the right side of PLC directly or connected to the remote
module that acts as PLC, e.g. the first connected module is module number 1, the second connected module is number
2. Up to 15 modules can be connected. If the connected module is not AS04SIL, the Error flag switches to ON.
2. Up to 32 modules can be connected and counted and each type of modules should be included in the count. If the
module is not AS04SIL, the Error flag switches to ON.
7. Port: The communication port number, ranging from 1 to 4. If the port number used is not the port for AS04SIL, the
Error flag switches to ON.
8. Index is the index number that is read from the parameter of the IO-Link device.
9. SubIndex is the sub-index number that is read from the parameter of the IO-Link device. The sub-index number can
be set from 0 to 255. If the value exceeds the setting range, the Error flag switches to ON.
10. DateType is the parameter data type of the IO-Link device. You need to set the correct datatype before executing this
instruction.
6-514
If the setting value exceeds the setting range, the Error flag switches to ON.
Error Code Data Type Description
0x0000 BooleanT Boolean; data length: 1 byte
0x0001 UIntegerT Unsigned integer; data length: 1, 2, 4, 8 byte
0x0002 IntegerT Signed integer; data length: 1, 2, 4, 8 byte
0x0003 Float32T Floating-point; data length: 4 byte
String; data length: 1~232 byte; Null (0x00) is seen as the ending character for
0x0004 StringT
the string.
0x0005 OctetStringT Fixed length string, defined by the IODD fixed length; data length: 1~232 byte
Time; data length: 4 byte (Resolution: 1 second) + 4 Byte (Resolution: 2^-32

0x0006 TimeT
second)
0x0007 TimeSpanT Time; data length: 8 byte (Resolution: 2^-32 second)
0x0008 ArrayT A whole array that is read from the sub-index number 0
0x0009 RecordT A whole record that is read from the sub-index number 0
Others Reserved Reserved
11. DataRead is the data read from the IO-Link device; unit: byte, arranged by high byte and low byte.
12. ReadLen is the data length of the data read from the IO-Link device; unit: byte.
13. Done is a communication complete flag. When this flag is ON, it indicates the parameter of the IO-Link device is read
completely. The range of the read data (ReadData) will be used according to the data length (READLen).
6_
14. Error is a communication error flag. When this flag is ON, it indicates an error occurs during the communication among
the PLC CPU, AS04SIL and the IO-Link device. Refer to the following Error Codes for troubleshooting.
Error Code Description
0x8000 IO-Link device application error
0x8011 The main index does NOT exist.
0x8012 The sub-index does NOT exist.
0x8020 The function is currently NOT available.
0x8021 The function is currently NOT available – Local Control.
0x8022 The function is currently NOT available – Device Control.
0x8023 Access denied.
0x8030 The parameter exceeds the setting range.
0x8031 The parameter exceeds the upper limit.
0x8032 The parameter exceeds the lower limit.
0x8033 The parameter length overrun
6-515
0x8034 The parameter length underrun
0x8035 The function is NOT available.
0x8036 The function is currently NOT available.
0x8040 Invalid parameters set
0x8041 Inconsistent parameters set
0x8082 Application is NOT ready for use.
0x8101 The IO-Link device is NOT in IO-Link mode.
0x8102 The communication port is NOT connected to any IO-Link device.
0x8103 The connection to IO-Link device is establishing.
0x8104 Communication port number exceeds the setting range 1~4.
0x8105 The sub-index number of the parameter exceeds the setting range 0~255.
0x8106 The data to be read and written exceeds the setting range 1~232.
0x8107 Reserved
0x8108 Communication timeout; no response from IO-Link device for over 5000 ms.
0x8109 Incorrect AS04SIL module number or group number
0x810A Internal communication error
0x810B Execute more than two IO-Link read/write instructions on the same AS04SIL module.
The starting address of the read/write device + the data length to read/write exceed the device
0x810C
setting range.
0x810D The value of the parameter data type exceeds the setting range.
_6 0x810E The parameter data type and the read/write data length are inconsistent.
16. The communication process among the PLC CPU, AS04SIL and IO-Link device:
A: The PLC CPU sends data to AS04SIL.

B: AS04SIL sends data to the IO-Link device.
C: the IO-Lind Device is processing the request and send
data to AS04SIL.
D: The PLC CPU updates the status (DONE / ERROR) and
receives the data.
6-516
17. Sequences of the EN, Done, and Error flags: when an error occurs during communication (scenario 1) and when the
communication is compete (scenario 1).
Example 1: Read the parameter of Application Specific Tag on the first device of the first communication port.
1. Check HWCONFIG to learn the setting value in Application Specific Tag is “ABCDEFGH”.
2. AS04SIL is the first module that installed on the right side of the PLC CPU. The setting value in Group is 0, and 1 in
both Module and Port. 6_

3. We learnt that its index is 24, its Sub-index is 0, and the data type is StringT from its IODD file or the IO-Link device
manual. Set the setting values in Index to 24, in Sub-index to 0, in data type to 4 (StringT).
4. Start sending “to read” request when M0 is ON. When M10 (DONE) is ON, it indicates the device has responded
and has complete reading. ReadLen (D40) is 32, and the data string is stored in DataRead (D50~D65). IO-Link
device reads the data and stores it in accordance with the order of high byte and low byte.
6-517
Example 2: Read the parameter of gain trim green channel on the first device of the second communication port.
1. Check HWCONFIG to learn the setting value in gain trim green channel is “-63”.
2. AS04SIL is the first module that installed on the right side of the PLC CPU. The setting value in Group is 0, 1 in
Module and 2 in Port.
_6
3. We learnt that its index is 72, its Sub-index is 0, and the data type is IntegerT from its IODD file or the IO-Link device
manual. Set the setting values in Index to 72, in Sub-index to 0, in data type to 2 (IntegerT).
and has complete reading. ReadLen (D40) is 1, and the data is stored in DataRead (D50 Low Byte). IO-Link device
reads the data and stores it in accordance with the order of high byte and low byte.
6-518
Example 3: Read the parameter of gain trim green channel on the first device of the second communication port.
1. Check HWCONFIG to learn the setting value in Ambient temperature is 28.60551.
2. AS04SIL is the first module that installed on the right side of the PLC CPU. The setting value in Group is 0, 1
3. We learnt that its index is 268, its Sub-index is 0, and the data type is Float32T from its IODD file or the IO-Link
device manual. Set the setting values in Index to 268, in Sub-index to 0, in data type to 3 (Float32T).
and has complete reading. ReadLen (D40) is 4, and the data is stored in DataRead (D50~D51). IO-Link device
reads the data and stores it in accordance with the order of high byte and low byte.
6_
6-519

Write the parameter into the IO-Link
1427 IOLINKW Execute ~ ErrCode
device
Group   
Module   
Port   
Index   
SubIndex   
DataType   
WriteLen   
DataWrite 
Done    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
DINT
LINT
TMR
CNT
INT
Device
Group  
Module  
_6 Port  
Index  
SubIndex  
DataType  
WriteLen  
DataWrite  
Done 
Error 
ErrCode  

－ AS －
6-520
Symbol
Port ： Communication port number
Index ： Index number of the parameter
SubIndex ： Subindex number of the parameter
DataType ： Data type
WriteLen ： The length of the written data
DataWrite ： Data that is written
Done ： Communication complete
Explanation
2. You can refer to the IODD file of the IO-Link device to learn more about the device parameters. You can also use this 6_
instruction to write the parameters into the IO-Link device.
3. There is no limit on the number of times you execute the instruction but only one instruction (IOLINKR or IOLINKW)
can be executed at a time.
4. During communication, it takes at least 5 seconds for the IO-Link device to response. Do NOT stop or start another
instruction during this time. After the communication with IO-Link is done, it is suggested to use the flags DONE or
ERROR to stop or start the instruction.
5. Group: The group number of AS04SIL that is connected to the right side of PLC directly or connected to the remote
module that acts as PLC, e.g. the first connected module is module number 1, the second connected module is number
2. Up to 15 modules can be connected. If the connected module is not AS04SIL, the Error flag switches to ON.
2. Up to 32 modules can be connected and counted and each type of modules should be included in the count. If the
module is not AS04SIL, the Error flag switches to ON.
7. Port: The communication port number, ranging from 1 to 4. If the port number used is not the port for AS04SIL, the
Error flag switches to ON.
8. Index is the parameter index number that is intended to write into the IO-Link device.
6-521
9. SubIndex is the parameter sub-index number that is intended to write into the IO-Link device. The sub-index number
can be set from 0 to 255. If the value exceeds the setting range, the Error flag switches to ON.
10. DateType is the parameter data type of the IO-Link device. You need to set the correct datatype before executing this
instruction. Refer to API1426 IOLINKR instruction for more information.
11. DataWrite is the data written into the IO-Link device; unit: byte, arranged by high byte and low byte.
12. WriteLen is the data length of the data to be written into the IO-Link device; unit: byte.
13. Done is a communication complete flag. When this flag is ON, it indicates the parameters have written into the IO-
Link device completely.
14. Error is a communication error flag. When this flag is ON, it indicates an error occurs during the communication among
the PLC CPU, AS04SIL and the IO-Link device. Refer to the Error Codes from API1426 IOLINKR instruction for
troubleshooting.
18. The communication process among the PLC CPU, AS04SIL and IO-Link device:
A: The PLC CPU sends data to AS04SIL.

B: AS04SIL sends data to the IO-Link device.
_6
C: the IO-Lind Device is processing the request
and send data to AS04SIL.
D: The PLC CPU updates the status (DONE /
ERROR) and receives the data.
19. Sequences of the EN, Done, and Error flags: when an error occurs during communication (scenario 1) and when the
communication is compete (scenario 1).
6-522
Example 1: Write the parameter of Application Specific Tag into the first device of the first communication port.
1. Check HWCONFIG to learn the setting value in Application Specific Tag is “ABCDEFGH”.
3. We learnt that its index is 24, its Sub-index is 0, and the data type is StringT from its IODD file or the IO-Link device
manual. Set the setting values in Index to 24, in Sub-index to 0, in data type to 4 (StringT).
4. Use the instruction $MOV to write the string “IO-Link” into the data device, starting from D60.
5. Start sending “to write” request when M1 is ON. When M10 (DONE) is ON, it indicates the device has received the
response and has complete writing. WriteLen is 32, and the data string is saved in DataWrite (D60~D75). IO-Link
device writes the data into the data devices in accordance with the order of high byte and low byte.
6_
6-523
6. Check HWCONFIG to learn the setting value in Application Specific Tag is updated to “IO-Link”.
Example 2: Write the parameter of gain trim green channel into the first device of the second communication
port.
1. Check HWCONFIG to learn the setting value in gain trim green channel is “-63”.
_6
3. We learnt that its index is 72, its Sub-index is 0, and the data type is IntegerT from its IODD file or the IO-Link device
manual. Set the setting values in Index to 72, in Sub-index to 0, in data type to 2 (IntegerT).
4. Use the instruction $MOV to write 0xE2 (-30) into the data device, starting from D60.
5. Start sending “to write” request when M1 is ON. When M10 (DONE) is ON, it indicates the device has received the
response and has complete writing. WriteLen is 1, and the data is saved in DataWrite (D60 Low byte). IO-Link
device writes the data into the data devices in accordance with the order of high byte and low byte.
6-524
6_
7. Check HWCONFIG to learn the setting value in gain trim green channel is updated to “-30”.
6-525
6.16 Floating-point Number Instructions

6.16.1 List of Floating-point Number Instructions
The following table lists the Module instructions covered in this section.

API Function
1500 – FSIN  Sine of a floating-point number
1501 – FCOS  Cosine of a floating-point number
1502 – FTAN  Tangent of a floating-point number
1503 – FASIN  Arcsine of a floating-point number
1504 – FACOS  Arccosine of a floating-point number
1505 – FATAN  Arctangent of a floating-point number
1506 – FSINH  Hyperbolic sine of a floating-point number
1507 – FCOSH  Hyperbolic cosine of a floating-point number
1508 – FTANH  Hyperbolic tangent of a floating-point number
1509 – FRAD  Converting degrees to radians
1510 – FDEG  Converting radians to the degrees

_6
1512 – FSQR  Square root of a floating-point number
1513 – FEXP  Exponentiation of a floating-point number
1514 – FLOG  Logarithm of a floating-point number
1515 – FLN  Natural logarithm of a binary floating-point number
1516 – FPOW  Power of a floating-point number
1517 RAND –  Generating a random number
6-526
6.16.2 Explanation of Floating-point Number Instructions
1500 FSIN P S, D Sine of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Sine value
Explanation
1. This instruction finds the sine of the value in S and stores it in D. The state of SM695 determines whether the
source value in S is in radians or degrees. 6_
2. If SM695 is OFF, the source value is S in radians

Radian=Degree×π/180.
3. If SM695 is ON, the source value in S is in degrees.
Degree=Radian×180/π. (0o≦Degree≦3600)
4. If the conversion result is zero, SM600 is ON.
5. The following graph shows the relation between radian and sine values.
6-527
Example
When X0.0 is ON, the BIN instruction converts the binary-coded decimal value in X1.15–X1.0 into the binary value, and
stores the conversion result in D0. The FLT instruction converts the binary value in D0 into a floating-point number, and
stores the conversion result in (D11, D10). The FRAD instruction converts a floating-point number in (D11, D10) into
radians, and stores the conversion result in (D21, D20). The FSIN instruction finds the sine of the radian value in (D21,
D20), and stores it in (D31, D30). The sine value is a floating-point number.
X1.15~X1.0 BIN D0 F LT D11~D10

0 0 9 0 90 R90
_6 Binary -coded Binary val ue F loating- point
decimal value number
F RAD D21~D20 F SIN D31~D30

R1.570796 R1
F loating- point F loating- point
number number
Additional remarks
1. If the value in S exceeds the range of values that can be represented by floating-point numbers, the instruction is
not executed, SM0 is ON, and the error code in SR0 is 16#2013.
2. If SM695 is ON, and the value in S is not between 0–360, the instruction is not executed, SM0 is ON, and the error
code is 16#2003.
6-528
1501 FCOS P S, D Cosine of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Cosine value
Explanation
1. This instruction finds the cosine of the value in S and stores it in D. The state of SM695 determines whether the
source value in S is in radians or degrees. 6_

2. If SM695 is OFF, the source value in S is in radians.
5. The following graph shows the relation between radians and cosine values.
6-529
Example
stores the conversion result in D0. The FLT instruction converts the binary value in D0 into a floating-point number, and
stores the conversion result in (D11, D10). The FRAD instruction converts a floating-point number in (D11, D10) into
radians, and stores the conversion result in (D21, D20). The FCOS instruction finds the cosine of the radian value in
(D21, D20) and stores it in (D31, D30). The cosine value is a floating-point number.
_6 X1.15~X1.0 BIN D0 F LT D11~D10

0 3 6 0 360 R360
Binary -coded Binary value F loating-point
F RAD D21~D20 F CO S D31~D30

R6.283185 R1
F loating-point F loating-point
number number
Additional remarks
code is 16#2003.
6-530
1502 FTAN P S, D Tangent of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Tangent value
Explanation
1. This instruction finds the tangent of the value in S and stores it in D. The state of SM695 determines whether the
source value in S is in radians or in degrees.

6_
2. If SM695 is OFF, the source value in S is in radians.
5. The following graph shows the relation between radians and tangent values.
6-531
Example
stores the conversion result in D0. The FLT instruction converts the binary value in D0 into the floating-point number, and
stores the conversion result in (D11, D10). The FRAD instruction converts the floating-point number in (D11, D10) into
radians, and stores the conversion result in (D21, D20). The FTAN instruction finds the tangent of the radian value in
(D21, D20) and stores it in (D31, D30). The tangent value is a floating-point number.
_6
X1.15~X1.0 BIN D0 F LT D11~D10

0 0 4 5 45 R56
Binary -coded Binary val ue F loating- point
F RAD D21~D20 F TAN D31~D30

R0.785398 R1
F loating- point F loating- point
number number
6-532
Additional remarks
code is 16#2003.
6_
6-533
1503 FASIN P S, D Arcsine of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Arcsine value
_6 Explanation
1. This instruction finds the arcsine of the value in S and stores it in D. Arcsine value=sin-1
The following graph shows the relation between sine and arcsine values.
6-534
Example
When X0.0 is ON, the instruction finds the arcsine of the floating-point number in (D1, D0) and stores it in (D11, D10).
The FDEG instruction converts the arcsine value in (D11, D10) into degrees, and stores the conversion result in (D21,
D20). The DINT instruction converts the degree value in (D21, D20) into the integer, and stores the conversion result in
(D31, D30). The BCD instruction converts the integer in (D31, D30) into the binary-coded decimal value, and stores the
conversion result in Y0.15–Y0.0.
D0 FAS IN D11~D10 FDEG D21~D20

R1 R1.570796 R90
Floating-point number Float ing-point number Floating-point number 6_
DINT D31~D30 B CD Y0.15~Y0.0
90 0 0 9 0
Binary value Binary-coded decimal value
Additional remarks
1. The floating-point number specified by the operand S must be between –1.0 to 1.0. If the floating-point number is
not in that range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6-535
1504 FACOS P S, D Arccosine of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Arccosine value
Explanation
1. This instruction finds the arccosine of the value in S and stores it in D. Arccosine value=cos-1
The following graph shows the relation between cosine and arccosine values.
_6
2. If the absolute value of the conversion result is larger than the value that can be represented by the maximum
3. If the absolute value of the conversion result is less than the value that can be represented by the minimum
6-536
Example
When X0.0 is ON, the FACOS instruction finds the arccosine of the floating-point number in (D1, D0) and stores it in
(D11, D10). The FDEG instruction converts the arccosine value in (D11, D10) into degrees, and stores the conversion
result in (D21, D20). The DINT instruction converts the degrees value in (D21, D20) into an integer, and stores the
conversion result in (D31, D30). The BCD instruction converts the integer in (D31, D30) into a binary-coded decimal
value, and stores the conversion result in Y0.15–Y0.0.
D0 FACOS D11~D10 FD EG D2 1~D20

R1 80
6_
R1 R3 .14 159 2
Floating-point number Floating-point number Floating-point number
D INT D31 ~D30 BCD Y0.15 ~Y0.0
18 0 0 1 8 0
Binary value Binary-coded decimal value
Additional remarks
1. The floating-point number specified by the operand S must be between –1.0 to 1.0. If the floating-point number is
not in the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6-537
1505 FATAN P S, D Arctangent of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Arctangent value
Explanation
_6
1. This instruction finds the arctangent of the value in S and stores it in D. Arctangent value=tan-1
2. The following graph shows the relation between tangent and arctangent values.
6-538
Example
When X0.0 is ON, the FATAN instruction finds the arctangent of the floating-point number in (D1, D0) and stores it in
(D11, D10). The FDEG instruction converts the arctangent value in (D11, D10) is converted into degrees, and stores the
conversion result in (D21, D20). The DINT instruction converts the degree in (D21, D20) into the integer, and stores the
conversion result in (D31, D30). The BCD instruction converts the integer in (D31, D30) into the binary-coded decimal
value, and stores the conversion result in Y0.15–Y0.0.
D0 F ATAN D11~D10 F DEG D21~D20

R1 R0.785398 R45
6_
F loating- point F loating- point F loating- point
number number number
DINT D31~D30 BCD Y1.15~Y1.0

45 0 0 4 5
Binary v al ue Binary -coded
decimal value
Additional remarks
If the value in S exceeds the range of values that can be represented by floating-point numbers, the instruction is not
6-539
1506 FSINH P S, D Hyperbolic sine of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ：
D ：
Explanation
_6 1. This instruction finds the hyperbolic sine of the value in S and stores it in D. Hyperbolic sine value=(es-e-s)/2.
2. If the absolute value of the conversion result is larger than the value that can be represented by floating-point
numbers, the value in D is 16#7F800000, and SM602 is ON.
3. If the absolute value of the conversion result is less than the value that can be represented by floating-point
numbers, the value in D is 16#FF800000, and SM601 is ON.
Example
1. When X0.0 is ON, the instruction finds the hyperbolic sine of the floating-point number in (D1, D0) and stores it in
(D11, D10). The hyperbolic sine value in (D11, D10) is a floating-point number.
6-540
S Single-pr ecision
D1 D0
floati ng- poi nt number
D D11 D10 Hyperbolic sine value
numbers, SM602 is ON.
Additional remarks
6_
6-541

Hyperbolic cosine of a floating-point
1507 FCOSH P S, D
number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Hyperbolic cosine value
Explanation
_6 1. This instruction finds the hyperbolic cosine of the value in S and stores it in D. Hyperbolic cosine value=(es+e-s)/2.
numbers, the value in D is 16#7F800000, and SM602 is ON.
Example
1. When X0.0 is ON, the instruction finds the hyperbolic cosine of the floating-point number in (D1, D0) and stores it
in (D11, D10). The hyperbolic cosine value in (D11, D10) is a floating-point number.
6-542
S D1 D0 Single-pr ecision
floati ng- point number
D D11 D10 Hyperbolic cosi ne value
Additional remarks
6_
6-543

Hyperbolic tangent of a floating-point
1508 FTANH P S, D
number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
D ： Hyperbolic tangent value
Explanation
1. This instruction finds the hyperbolic tangent of the value in S and stores it in D.
Hyperbolic tangent value=(es-e-s)/(es+e-s).
_6 2. If the conversion result is 0, SM600 is ON.
Example
1. When X0.0 is ON, the instruction finds the hyperbolic tangent of the floating-point number in (D1, D0) and stores it
in (D11, D10). The hyperbolic tangent value in (D11, D10) is a floating-point number.
Single- pr ecision
S D1 D0
floati ng- point number
D D11 D10 Hyperbolic tangent value
6-544
Additional remarks
6_
6-545
1509 FRAD P S, D Converting degrees to radians

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value (in degrees)
D ： Conversion result (in radians)
Explanation
1. This instruction converts the degrees value in S into radians, and stores it in D.
_6
2. Radian＝Degree×(π/180).
Example
When X0.0 is ON, the instruction converts the degree value in (D1, D0) to the radians value, and stores the conversion
result in (D11, D10). The radian in (D11, D10) is a floating-point number.
Degree
S D1 D0
F loating- point number
D D11 D10 Radian (Degree ×π/180 )

F loating- point number
6-546
Additional remarks
6_
6-547
1510 FDEG P S, D Converting radians to degrees

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value (in radians)
D ： Conversion result (in degrees)
Explanation
1. This instruction converts the radians value in S to degrees, and stores it in D.
2. Degree＝Radian×(180/π).
_6
numbers, the value in D is 16#7F7FFFFF.
numbers, the value in D is 16#7F7FFFFF.
Example
When X0.0 is ON, the instruction converts the radians values in (D1, D0) to the degree value, and stores the conversion
result in (D11, D10). The degree in (D11, D10) is a floating-point number.
6-548
Radian
S D1 D0 Fl oating-point number
D D11 D10 Degree ( Radian×180 /π )

Fl oating-point number
Additional remarks
6_
6-549
1511 D SQR P S, D Square root of a binary number

S           
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S      
     

AS AS AS
Symbol
S ： Source value
D ： Device where the result is stored
Explanation
_6 1. This instruction calculates the square root of the value in S, and stores the result in the device specified by D.
2. The operation result stored in D is an integer. If a floating-point number is rounded down to the nearest whole digit,
SM601 is ON.
3. If the operation result stored in D is 0, SM600 is ON.
Example
When X0.0 is ON, the instruction calculates the square root of the value in D0, and stores the result in D10.
6-550
Additional remarks
The value in S only can be a positive value. If the value in S is a negative value, an operation error occurs, the instruction
is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6_
6-551
1512 FSQR P S, D Square root of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value
Explanation
1. This instruction calculates the square root of the floating-point number in S, and stores the result in the device
specified by D.
_6 2. If the operation result stored in D is 0, SM600 is ON.
Example 1
When X0.0 is ON, the instruction calculates the square root of the floating-point number in (D1, D0), and stores the result
in (D11, D10).
Additional remarks
The value in S only can be a positive value. If the value in S is a negative value, an operation error occurs, the instruction
is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6-552
1513 FEXP P S, D Exponentiation of a floating-point number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value (exponent)
Device where the operation result is

D ：
stored
Explanation
1. This function calculates the value of the number e raised to the power in S. Exponentiation involves two numbers,
the base e which represents 2.71828, and the exponent in S.
2. EXP[D+1, D]=[S+1, S]. 6_

3. The number in S can be a positive number or a negative number. The device specified by D should be a 32-bit
register, and the number in the device specified by S should be a floating-point number.
4. The value in the register specified by D is eS (e is 2.71828, and S represents the source value).
numbers, the value in the register specified by D is 16#7F800000, and SM602 is ON.
Example
1. When X0.0 is ON, the DFLT instruction converts the value in (D1, D0) into a floating-point number, and stores the
2. When X0.1 is ON, the FEXP instruction performs the exponentiation with the value in (D11, D10), and stores the
floating-point number result in (D21, D20).
6-553
_6
6-554
1514 FLOG P S1, S2, D Logarithm of a floating-point number

S1         
S2         
D  DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS - AS
Symbol
S1 ： Base for the logarithm
S2 ： Source value
D ：
stored
Explanation
1. This instruction calculates the logarithm of the value in S2 with respect to the value in S1, and stores the single- 6_
precision floating-point operation result in D.
2. The values in S1 and S2 only can be positive values.
3. S1D=S2.→D=LogS1S2.
4. Example: suppose the values in S1 and S2 are 5 and 125 respectively. Find log5125 (log base 5 of the number
125).
5. S1D=S2.→5D=125.→D=log5125=3.
Example
1. When X0.0 is ON, the DFLT instruction converts the values in (D1, D0) and (D3, D2) into the floating-point
numbers, and stores the conversion results in (D11, D10) and (D13, D12) respectively.
2. When X0.1 is ON, the FLOG instruction calculates the logarithm of the floating-point number in (D13, D12) with
6-555
respect to the floating-point number in (D11, D10), and stores the operation result in (D21, D20).
Additional remarks
If the value in S1 is less than or equal to 1, or if the value in S2 is less or equal to 0, the instruction is not executed, SM0
_6
6-556

Natural logarithm of a binary floating-point
1515 FLN P S, D
number

S         
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 

AS - AS
Symbol
S ： Source value

D：
stored
Explanation
1. This instruction calculates the natural logarithm of the operand S in a single-precision floating-point operation.
2. The value in S only can be a positive value.
6_
3. eD=S.→The value in D=lnS.
Example
1. When X0.0 is ON, the DFLT instruction converts the value in (D1, D0) into the floating-point number, and stores the
2. When X0.1 is ON, the FLN instruction calculates the natural logarithm of the floating-point number in (D11, D10),
and stores the operation result in (D21, D20).
6-557
Additional remarks
If the value in S is less than or equal to 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
_6
6-558
1516 FPOW P S1, S2, D Power of a floating-point number

S1        
S2        
D  DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2 
D 

AS - AS
Symbol
S1 ： Source value
S2 ： Exponent value
D ：
stored
Explanation
1. This instruction raises the single-precision floating-point number in S1 to the power of the value in S2, and stores 6_
the single-precision floating-point operation result in D.
2. D=POW[S1+1，S1]^[S2+1，S2]
3. The value in S1 only can be a positive value, but the value in S2 can be a positive value or a negative value.
4. Suppose the values in S1 and S2 are 5 and 3 respectively: D=53=125.
5. If the absolute value of the operation result is larger than the value that can be represented by floating-point
numbers, the value in D is 16#7F7FFFFF, and SM602 is ON.
6. If the absolute value of the operation result is less than the value that can be represented by floating-point
Example
1. When X0.0 is ON, the DFLT instruction converts the values in (D1, D0) and (D3, D2) into floating-point numbers,
and stores the conversion results in (D11, D10) and (D13, D12) respectively.
6-559
2. When X0.1 is ON, the FPOW instruction raises the floating-point number in (D11, D10) to the power of the floating-
point number in (D13, D12), and stores the operation result in (D21, D20).
3. When X0.2 is ON, the FBCD instruction converts the binary floating-point number in (D21, D20) into the binary-
coded decimal floating-point number, and stores the conversion result in (D31, D30).
_6
Additional remarks
If the value in S1 is less than 0, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
6-560
1517 RAND P S1, S2, D Generating a random number

S1          
S2          
D  DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  

AS AS -
Symbol
S1 ： Minimum value
S2 ： Maximum value
Explanation
1. This instruction generates a random number between the minimum value in S1 and the maximum value in S2, and 6_
then stores the result in D.
2. If the value in S1 is larger than the value in S2, the instruction takes the values in S1 and S2 as the maximum value
and the minimum value respectively.
Example
When X0.0 is ON, the instruction generates a random number between the minimum value in D0 and the maximum
value in D10, and stores the result in D20.
Additional remarks
The values in S1 and S2 must be between 0–32767. If the value in S1 or S2 exceeds the range, the instruction is not
6-561
6.17 Real-time Clock Instructions

6.17.1 List of Real-time Clock Instructions
The following table lists the Real-time Clock instructions covered in this section.

API Function
1600 TRD –  Reading the time
1601 TWR –  Writing the time
1602 T+ –  Adding the time
1603 T- –  Subtracting the time
1604 HOUR – – Running-time meter
1605 TCMP –  Comparing the time
1606 TZCP –  Time zone comparison
1607 DST –  Daylight saving time
1608 WWON – – Setting up weekly working time setup
_6
6-562
6.17.2 Explanation of Real-time Clock Instructions
1600 TRD P D Reading the time

D DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  

AS AS -
Symbol
Explanation
1. This instruction reads the current time from the built-in real time clock in the CPU module, and stores the current
6_
time in D.
2. The operand D occupies seven consecutive devices.
3. The built-in real-time clock provides the year, the week, the moth, the day, the minute, and the second. The data is
stored in SR391–SR397.
4. The last two digits of the year number for A.D. are stored in SR391.
Example
When M0 is ON, the instruction reads the current time from the real-time clock into D0–D6. The value 1 in SR397
represents Monday, the value 2 represents Tuesday, and this continues to the value 7 represents Sunday.
6-563
Special data General data

Item Value Item
register register
SR391 Year (A.D.) 00-99 D0 Year (A.D.)
SR392 Month 1-12 D1 Month
SR393 Day 1-31 D2 Day
SR394 Hour 0-23 D3 Hour
SR395 Minute 0-59 D4 Minute
SR396 Second 0-59 D5 Second
SR397 Week 1-7 D6 Week
Additional remarks
16#2003.
2. When SM220 is ON, the real-time clock is calibrated within ±30 seconds. If the value of the seconds read from the
real-time clock is between 0–29, the instruction clears the seconds value to zero. If the value of the seconds read
from the real-time clock is between 30–59, the instruction increments the value of the minute by one, and clears
the seconds value to zero.

_6
6-564
1601 TWR P S Writing the time

S    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

AS AS -
Symbol
S ： Data source
Explanation
1. This instruction adjusts the built-in real-time clock in the CPU module by writing the correct current time in S into
the built-in real-time clock.
2. The operand S occupies seven consecutive devices. (Use 24 hour time format)
3. The instruction instantly writes the new setting time into the real-time clock in the PLC. 6_
4. Make sure that when the instruction executes, the new setting time in S is consistent with the actual time.
5. It is suggested to use it as a pulse instruction. If the contact is normally open, the instruction is executed to write
the time constantly. But the PLC only writes the time at the first scan. If the built-in real-time clock needs to be
updated, you can close the contact for a scan time and then execute this instruction again to update the clock.
Example
When M0 is ON, the instruction writes the correct current time into the built-in real-time clock in the PLC.
6-565
General data Special data

Item Value Item
register register
D20 Year (A.D.) 00-99 SR391 Year (A.D.)
D21 Month 1-12 SR392 Month

New setting time
Real time clock

D22 Day 1-31 SR393 Day
D23 Hour 0-23 SR394 Hour
D24 Minute 0-59 SR395 Minute
D25 Second 0-59 SR396 Second
D26 Week 1-7 SR397 Week
Additional remarks
1. If the value in S exceeds the range, an operation error occurs, the instruction is not executed, SM is ON, and the
error code in SR is 16#2003.
2. If S+6 exceeds the device range, an operation error occurs, the instruction is not executed, SM is ON, and the
error code in SR is 16#2003.
3. If you declare the operand S in ISPSoft, the data type is ARRAY [7] of WORD/INT.
_6
6-566
1602 T+ P S1, S2, D Adding the time

S1     
S2     
D DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  

AS AS -
Symbol
Explanation 6_
1. This instruction adds the value of the hour, the minute, and the second in the real-time clock specified by S2 to the
value of the hour, the minute, and the second in the real-time clock specified by S1, and then stores the sum in the
register specified by D.
2. The operands S1, S2, and D each occupy three consecutive devices.
3. If the sum is larger than or equal to 24 hours, SM602 is ON, and the instruction subtracts 24 hours from the sum
before storing the result in D.
4. If the sum is zero (zero hour zero minute zero second), SM600 is ON.
Example
When M0 is ON, the instruction adds the value of the hour, the minute, and the second in D10–D12 to the value of the
hour, the minute, and the second in D0–D2, and stores the sum in D20–D22.
6-567
D0 8 ( Hour ) D10 6 ( Hour ) D20 14 ( Hour )

D1 10 ( Minute) + D11 40 ( Minute ) D21 50 ( Minute )
D2 20 ( Second) D12 6 ( Second ) D22 26 ( Second )
8 hour 10 minute 20 second 6 hour 40 minute 6 second 14 hour 50 minute 26 second
Additional remarks
1. If the value in S1 or S2 exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON,
2. If S1+2, S2+2, or D+2 exceeds the device range, an operation error occurs, the instruction is not executed, SM0 is
4. If you declare the operand S2 in ISPSoft, the data type is ARRAY [3] of WORD/IN.
_6
6-568
1603 T- P S1, S2, D Subtracting the time

S1     
S2     
D DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D  

AS AS -
Symbol
Explanation
1. This instruction subtracts the value of the hour, the minute, and the second in the real-time clock specified by S2 6_
from the value of the hour, the minute, and the second in the real-time clock specified by S1, and stores the
difference in the register specified by D.
2. The operands S1, S2, and D all occupy three consecutive devices.
3. If the difference is a negative, SM601 is ON, and the instruction adds 24 hours to the difference and then stores
the result in D.
4. If the difference is zero (zero hour zero minute zero second), SM600 is ON.
Example
1. When M0 is ON, the instruction subtracts the value of the hour, the minute, and the second in D10–D12 from the
value of the hour, the minute, and the second in D0–D2, and stores the difference in D20–D22.
D0 20 ( Hour ) D10 14 ( Hour ) D20 5 ( Hour )

D1 20 ( Minute) - D11 30 ( Minute ) D21 49 ( Minute )
D2 5 ( Second) D12 8 ( Second ) D22 57 ( Second )
20 hour 20 minute 50 second 14 hour 30 minute 8 second 5 hour 49 minute 57 second
6-569
2. If the difference is a negative, SM601 is ON.
5 ( Hour ) 19 ( Hour ) 10 ( Hour )

20 ( Minute) - 11 ( Minute) 9 ( Minute)
30 ( Second) 15 ( Second ) 15 ( Second )
5 hour 20 minute 30 second 19 hour 11 mi nute 15 second 10 hour 9 minute 15 second
Additional remarks
2. If S1+2, S2+2, or D+2 exceeds the device range, an operation error occurs, the instruction is not executed, SM0 is
_6
6-570
1604 HOUR S, D1, D2 Running-time meter

S        
D1 
D2   
DWORD  
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
D1  
D2 

- AS
Symbol
Time after which the output

S ：
device is ON
D1 ： Current time
D2 ： Output device
Explanation
1. This instruction switches the output device specified by D2 to ON after the amount of time in S. 6_
2. S: The time after which the output device is ON (Unit: Hour)
The operand S used in the 16-bit instruction must be between 1–32,767.
3. D1: The current time (Unit: Hour). The value in D1 must be between 0–32,767.
D1+1: The current time which is less than one hour (Unit: Second). The value in D1+1 should be between 0–3,599.
D1+2 is for system use only. The value in it cannot be altered when the instruction is executed; otherwise, an error
occurs.
When the current time is 32,767 hour 3,599 second, the timer stops counting. After the values in D1 and D1+1 are
cleared to 0, the timer starts to count again.
4. When the time for which the input contact has been ON reaches the setting time in S, the output device is ON.
Before that the output device is not ON. This function allows you to manage the running time of the machine and
maintenance.
5. After the output device is ON, the timer continues to count.
6-571
6. When using on-line editing, reset the conditional contact to initialize the instruction.
Example 1
When X0.0 is ON, the instruction timer starts to count. When the time for which X0.0 has been ON reaches 100 hours,
Y0.0 is ON. The current time is recorded in D0, and the current time which is less than one hour is recorded in D1. D2 is
for system use. The value in it cannot be altered; otherwise, an error occurs.
Additional remarks
1. When S is less than or equal to 0, the instruction is not executed, and the state of the output device is unchanged.
2. If the value in D1 is less than 0, the state of the output device is unchanged.
3. If D1+2 exceeds the device range, an operation error occurs, the instruction is not executed, SM0 is ON, and the
_6 error code in SR0 is 16#2003.
4. If you declare the operand D1 in ISPSoft, the data type is ARRAY [3] of WORD/INT.
6-572
1605 TCMP P S1, S2, S3, S, D Comparing the time
Device
X Y M S T C HC D FR SM SR E K 16# “$” F
S1          
S2          
S3          
S   
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
S  
D 

AS AS -
Symbol
S1 ： Hour for the setting time
S2 ： Minute for the setting time

6_
S3 ： Second for the setting time
S ： Current time
Explanation
1. This instruction compares the value of the hour, the minute, and the second specified by S1–S3 with the value of
the hour, the minute, and the second in the devices starting from the device specified by S, and stores the
comparison result in D.
2. The hour of the current time is in the device specified by S, and the value of the hour between 0–23. The minute of
the current time is in the device specified by S+1, and the value of the minute must be between 0–59. The second
of the current time is in the device specified by S+2, and the value of the second must be between 0–59.
3. The operand D occupies three consecutive devices. The comparison result is stored in D, D+1, and D+2.
4. In general, use the TRD instruction (API 1600) to read the current time from the real-time clock first, and then use
the TCMP instruction to compare the time.
5. If the setting time in S1-S3 is larger than the current time in S, D is ON, D+1 is OFF, and D+2 is OFF.
6-573
6. If the setting time in S1-S3 is equal to the current time in S, D is OFF, D+1 is ON, and D+2 is OFF.
7. If the setting time in S1-S3 is less than the current time in S, D is OFF, D+1 is OFF, and D+2 is ON.
Example
1. When X0.0 is ON, the instruction compares the setting time 12 hour 20 minute 45 second with the current time in
D20–D22, and stores the comparison result in M10–M12. When X0.0 switches from ON to OFF, the instruction is
not executed, and the states of M10, M11, and M12 remain the same as they were before X0.0 switched to ON.
2. If you want to get the comparison result ≧, ≦, or ≠, you can connect M10–M12 in series or in parallel.
_6
Additional remarks
1. If S+2 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
16#2003.
3. If the value in S exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and the
4. If the values in S1–S3 exceed the range, an operation error occurs, the instruction is not executed, SM0 is ON, and
the error code in SR0 is 16#2003.
6-574
5. If you declare the operand S in ISPSoft, the data type is ARRAY [3] of WORD.
6_
6-575
1606 TZCP P S1，S2，S，D Time zone comparison
Device
S1    
S2    
S   
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S  
D 

AS AS -
Symbol
S1 ： Lower limit time
S2 ： Upper limit time
S ： Current time
_6 D ： Comparison result
Explanation
1. This instruction compares the current time specified by S with the lower limit time specified by S1, and with the
upper limit time specified by S2, and stores the comparison result in D.
2. The hour of the lower limit time is in the device specified by S1, the minute of the lower limit time is in the device
specified by S1+1, and the second of the lower limit time is in the device specified by S1+2.
3. The hour of the upper limit time is in the device specified by S2, the minute of the upper limit time is in the device
specified by S2+1, and the second of the upper limit time is in the device specified by S2+2.
4. The hour of the current time is in the device specified by S, the minute of the current time is in the device specified
by S+1, and the second of the current time is in the device specified by S+2.
5. The time in the device specified by S1 must be less than the time in the device specified by S2. If the time in the
device specified by S1 is larger than the time in the device specified by S2, the instruction takes the time in the
device specified by S1 as the upper limit time during the execution of the instruction.
6. In general, use the TRD instruction (API 1600) to read the current time from the real-time clock first, and then use
6-576
the TZCP instruction to compare the time.
7. If the current time in the device specified by S is less than the lower limit time in the device specified by S1, and is
less than the upper limit time in the device specified by S2, D is ON. If the current time in the device specified by S
is larger than the lower limit time in the device specified by S1, and is larger than the upper limit time in the device
specified by S2, D+2 is ON; otherwise D+1 is ON.
Example
When X0.0 is ON, the TZCP instruction is executed. M10, M11, or M12 is ON. When X0.0 is OFF, the instruction is not
executed, the state of M10, the state of M11, and the state of M12 remain the same as before X0.0 switched to ON.
6_
Additional remarks
1. If S1+2, S2+2, S+2, or D+2 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code
in SR0 is 16#2003.
2. If the values in S1, S2, and S exceed the range, an operation error occurs, the instruction is not executed, SM0 is
ON, and the error code in SR0 is 16#2003
6-577
1607 DST P S, S1, S2, S3, S4, S5, D Daylight saving time
Device
S     
S1     
S2     
S3     
S4     
S5     
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
S1  
S2  
S3  
S4  
S5  
D 

AS AS -
_6 Symbol
S ： Daylight saving time function codes
S1 ： Month of the daylight saving start time
S2 ： Date of the daylight saving start time
S3 ： Month of the daylight saving end time
S4 ： Date of the daylight saving end time

Change due to daylight saving time
S5 ：
(minutes)
D ： The state of the daylight saving function
6-578
Explanation
1. Operands used in this instruction are described below:
S: Daylight saving time function codes
Firmware version before V1.04 (V1.04 excluded) supports the following function codes:
Function codes Description

0 Disable daylight saving time
1 Enable daylight saving time mode 1
2 Read daylight saving time
3~ Reserved or viewed as reading daylight saving time
Firmware version after V1.04 (V1.04 included) supports the following function codes:
Function codes Description

0 Disable daylight saving time
2 Read daylight saving time
4 Disable daylight saving time (set by the system)
5 Daylight saving time mode 1 enabled (set by the system) 6_
7 Daylight saving time mode 2 enabled (set by the system)
6, 8~ Reserved or viewed as reading daylight saving time
Note 1: When the code in S is 4, 5 or 7, the execution of instruction is of no use.
Note 2: Read more for information on the various modes in the following sections.
S1: setting for the month to start daylight saving time
S2: setting for the date to start daylight saving time
S=1 (daylight saving time mode 1 enabled), S2: settings for the date to start daylight saving time
S=3 (daylight saving time mode 2 enabled), S2: settings for the week to start daylight saving time, S2+1: on which
weekday of S2
S3: setting for the month to end daylight saving time
S4: settings for the date to end daylight saving time
S=1 (daylight saving time mode 1 enabled), S4: settings for the date to end daylight saving time
6-579
S=3 (daylight saving time mode 2 enabled), S4: settings for the week to end daylight saving time, S2+1: on which
weekday of S4
S5: settings for the change due to daylight saving time; unit: minute
D: stores the state of the daylight saving time; when the value in D is OFF, daylight saving time is disabled. When the
value in D is ON, daylight saving time is enabled.
2. Descriptions on the value in function code S for daylight saving time functions
D.S.T State S Function Code Description
Disabled 0 Disabled daylight saving time function
Enabled 1, 3 Enabled daylight saving time function
Read 2 Read the daylight saving time setting
• Disabled daylight saving time function (refer to example 1 below)

When the operand S is 0, the function of daylight saving time is disabled. When S is set to disable the daylight
saving time, the values in S1–S5 are irrelevant and the operand D shows the daylight saving time state as OFF.
• Enabled daylight saving time function (refer to example 2 and 3)

When the value in S is 1 or 3, daylight saving time function is enabled: S1 and S2: setting for the month to start
daylight saving time; S3 and S4: setting for the month to end daylight saving time; S5: settings for the change
due to daylight saving time; unit: minute; the operand D shows the daylight saving time state. When the
function of daylight saving time is enabled and the system runs for the first time during the start time (S1, S2),
_6 the system time adds the value set in S5 once. When the function of daylight saving time is disabled and the
system runs for the first time during the end time (S1, S2), the system time subtracts the value set in S5 once.
Modes for daylight saving
Mode S Function Code Rules Available for
Mode 1 1 By month and date V1.00 or later
Mode 2 3 By month and week V1.04 or later
6-580
Mode 1 (S=1): enabled by month and date (refer to example 2)
Operand Description
The month to start daylight saving time

S1
Range: 1-12
The date to start daylight saving time

S2
Range: 1-31
The month to end daylight saving time

S3
Range: 1-12
The date to end daylight saving time

S4
Range: 1-31
Time that changed due to daylight saving time; unit: minute

S5
Range: 1-1439 (within 1 day)
Note 1: If this function is enabled, the value in D is ON.
Note 2: If the date is set incorrectly, the daylight saving function cannot be enabled. The SM0 is ON, and the
error code in SR0 is 16#200B. For example if a non-existed date is set, such as April 31, or the
starting date is set smaller than the ending date in a calendar year, for example starting date is
October 1 and ending date is April 01.
Note 3: If S5 is set out of range, the daylight saving function cannot be enabled. The SM0 is ON, and the error
6_
code in SR0 is 16#200B.
Mode 2 (S=3): enabled by week and weekday (refer to example 3)
Operand Description
The month to start daylight saving time

S1
Range: 1-12
S2 S2: settings for the week to start daylight saving time; range: 1-4
S2+1 S2+1: on which weekday of the S2; range: 1-7 (Monday: 1, Tuesday: 2…, Sunday: 7)
The month to end daylight saving time

S3
Range: 1-12
S4 S4: settings for the week to end daylight saving time; range: 1-4
S4+1 S4+1: on which weekday of the S4; range: 1-7 (Monday: 1, Tuesday: 2…, Sunday: 7)
Time that changed due to daylight saving time; unit: minute

S5
Range: 1-1439 (within 1 day)
6-581
Note 1: If this function is enabled, the value in D is ON.
Note 2: The setting range for S2 and S4 is 1— 4 or -1— -4. The value -1 indicates the last week of the month
and -2 indicates the last 2nd week. If the value in S2 is -2 and S2+1 is 7, it indicates the last 2 Sunday
of the month. If the date is set incorrectly, the daylight saving function cannot be enabled. The SM0 is
ON, and the error code in SR0 is 16#200B.
Note 3: If the value in S2+1 / S4+1 is out of range, the default setting value is 7, indicating Sunday.
Note 4: If S5 is set out of range, the daylight saving function cannot be enabled. The SM0 is ON, and the error
code in SR0 is 16#200B.
Note 5: If the device for operand S2 and S4 is K or 16#, the values are not saved, the SM0 is ON, and the error
• Read the daylight saving time function (refer to example 1-3)
When the operand S is 2, the function of daylight saving time is being read. S1 and S2: setting for the month to start
daylight saving time; S3 and S4: setting for the month to end daylight saving time; S5: settings for the change due to
daylight saving time; unit: minute. When S is set to read the state of the daylight saving function and the output state
of D is ON, the PLC saves the setting values in the operands S1–S5. The device is set to D while S is set to read. If
the device is set to K or 16#, the values are not saved, the SM0 is ON, and the error code in SR0 is 16#2003.
Devices with firmware version after V1.04 (V1.04 included) adds 4 to the function codes in S, after the daylight saving
state is read. For example, after the daylight saving state is read, the function codes 0, 1, 3 become 4, 5 and 7.
_6 When the DST state is OFF, the operand and descriptions are shown below.
Operand Description
Before firmware V1.04 (V1.04 excluded), function code is fixed to 2.

S
After firmware V1.04 (V1.04 included), function code is 4, indicating the DST state is OFF.
S1- S5 Invalid operand
D DST state is OFF.
When the DST state is ON and in mode 1, the operand and descriptions are shown below.
Operand Description
Before firmware V1.04 (V1.04 excluded), function code is fixed to 2.
S After firmware V1.04 (V1.04 included), function code is 5, indicating the DST state is ON
and in mode 1.
S1 The month to start daylight saving time
S2 The date to start daylight saving time
S3 The month to end daylight saving time
S4 The date to end daylight saving time
S5 Time that changed due to daylight saving time; unit: minute
6-582
Operand Description
D The DST state is ON (enabled).
When the DST state is ON and in mode 2, the operand and descriptions are shown below.
Operand Description
S Function code is 7, indicating the DST state is ON and in mode 2.
S1 The month to start daylight saving time
S2 S2: settings for the week to start daylight saving time
S2+1 S2+1: on which weekday of the S2
S3 The month to end daylight saving time
S4 S4: settings for the week to end daylight saving time
S4+1 S4+1: on which weekday of the S4
S5 Time that changed due to daylight saving time; unit: minute
Operand The DST state is ON (enabled).
3. This instruction is to enable / disable the daylight saving time function. Whether the contact is normally open or close
will not affect the daylight saving time setting. (refer to example 2 for more details on how to switch the contact M0
OFF=>ON) You can reset the daylight saving time by executing the instruction again. There is no need to disable
and then enable this function to reset the daylight saving time.
4. When setting the daylight saving time to start on April 1st and to end on September 1st, and the duration is 60 minutes;
the real-time clock goes like below.
6_
Daylight saving time function disabled Daylight saving time function enabled
1st March, 3 o’clock 1st March, 3 o’clock
31st March, 3 o’clock 31st March, 3 o’clock
1st April, 3 o’clock 1st April, 4 o’clock
1st May, 3 o’clock 1st May, 4 o’clock
1st June, 3 o’clock 1st June, 4 o’clock
1st July, 3 o’clock, 1st July, 4 o’clock
1st August, 3 o’clock 1st August, 4 o’clock,
31st August, 3 o’clock 31st August, 4 o’clock
1st September, 3 o’clock 1st September, 3 o’clock
6-583
Example 1
Disable DST function and read the DST state.
Setting values and descriptions:
Device Setting Value Description
D0 0 Disable DST function
D1 X Invalid operand

_6
Enable contact M0
Y0.0=OFF, indicating DST function is disabled.
D100=K2, indicating DST state is being read.
Enable contact M1
Before firmware V1.04 (V1.04 excluded), function code is fixed to 2,

2
indicating the DST state is being read.
D100
After firmware V1.04 (V1.04 included), function code is 4, indicating
4
the DST state is OFF.
6-584
Y0.1 OFF Node state is OFF.
Example 2
Enable DST function and read the DST state.
Set the DST to start on 1st April and to end on 3rd September and the duration is 60 minutes.
6_
D0 1 The DST state is ON and in mode 1.
D1 4 Starting month: April
D2 1 Starting date: the 1st
D11 9 Ending month: September
D12 3 Ending date: the 3rd
D20 60 Duration: 60 minutes
Enable contact M0
Y0.0=ON, indicating DST function is enabled.
The PLC system time adds 60 minutes when the date April 1st arrives, and subtracts 60 minutes when the date
September 3rd arrives to end daylight saving time.
6-585
Enable contact M1
Setting
Device Description
Value

2
D100
After firmware V1.04 (V1.04 included), function code is 5, indicating the DST
5
state is ON and in mode 1.
Y0.1 ON Node state is ON.
Use the instruction DST or HWCONFIG in ISPSoft to read the daylight saving state. The HWCONFIG converts the result
from week number to the corresponding dates and months automatically.
Enable the contact M0 OFF=>ON again; this act has no impact on the DST. The DST does not reset.
_6 Device
Setting
Description
Value

2
D100
5
If the daylight saving time starts from 3 o’clock of 1st April, 60 minutes is added; the real-time clock shows 4 o’clock of 1st
April. No matter how many times the contact M0 is disabled or enabled, the real-time clock keeps the same daylight
saving time.
6-586
Example 3
Enable DST function and in mode 2.
Set the DST to start from the 2nd Wednesday of May and to end on 3rd Friday of September and the duration is 60
minutes.
D0 3 The DST state is ON and in mode 2.

6_
D1 5 Starting month: May
D2 2 Starting week number: the 2nd week
D3 3 Starting day: Wednesday
D12 3 Ending week number: the 3rd week
D13 5 Ending day: Friday
Enable contact M0
Y0.0=ON, indicating DST function is enabled.
For the year 2017, the 2nd Wednesday of May is 10th May and the 3rd Friday of September is 15th September. The PLC
system time adds 60 minutes when the date May 10th arrives and subtracts 60 minutes when the date September 15th
arrives to end daylight saving time.
6-587
Enable contact M1
Setting
Device Description
Value

2
D100
7
D101 5 Starting month: May
D102 2 Starting week number: the 2nd week
D103 3 Starting day: Wednesday
D112 3 Ending week number: the 3rd week
D113 5 Ending day: Friday
Use the instruction DST or HWCONFIG in ISPSoft to read the daylight saving state. The HWCONFIG converts the result
from week number to the corresponding dates and months automatically.
_6
6-588
1608 WWON S1, S2, D Setting up weekly working time
Device
S1 
S2 
S3 
S4 
D   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
S4  
D 

- AS -
Symbol
The hour to start working (occupies 7 consecutive
S1 ：
devices)
The minute to start working (occupies 7 consecutive
S2 ：
devices)
The hour to stop working (occupies 7 consecutive
6_
S3 ：
devices)
The minute to stop working (occupies 7 consecutive
S4 ：
devices)
D ： Output control
Explanation
1. This instruction allows you to set the time to start working for the week. S1–S1+6 allows you to set the time on Sunday
/ Monday / Tuesday / Wednesday / Thursday / Friday / Saturday respectively. This operand occupies 7 consecutive
devices. You can use the variables in an ARRAY to declare the operands.
2. S2–S2+6 S1–S1+6 allows you to set the minutes to start working on Sunday / Monday / Tuesday / Wednesday /
Thursday / Friday / Saturday respectively. This operand occupies 7 consecutive devices. You can use the variables
in an ARRAY to declare the operands.
3. S3–S3+6 allows you to set the hour to stop working on Sunday / Monday / Tuesday / Wednesday / Thursday / Friday /
Saturday respectively. This operand occupies 7 consecutive devices. You can use the variables in an ARRAY to
declare the operands.
4. S4–S4+6 allows you to set the minutes to stop working on Sunday / Monday / Tuesday / Wednesday / Thursday /
6-589
Friday / Saturday respectively. This operand occupies 7 consecutive devices. You can use the variables in an ARRAY
to declare the operands.
5. When the hour value in S1 is larger than the value set in S3, it means the time to stop working is the next day. For
example, when you set the time to start working at 18:00 on Monday and the time to stop working at 6:00, it means
the time to stop working is at 6:00 Tuesday.
Start working time Stop working time
Day Start Hour Start Minute Stop Hour Stop Minute
Sunday S1 24 S2 00 S3 24 S4 00
Monday S1+1 18 S2+1 00 S3+1 06 S4+1 00
6. The setting value for the hour is between 0–23. When the setting value is out of range, this function is not enabled.
The setting value for the minute is between 0–59. When the setting value is out of range, this function is enabled but
uses 0 as the setting value.
7. When it is required to set the work time to be more than 1 day, you can set the hour as 24, which means the system
does not check the start working time and the stop working time. For example, to set the start working time to 8 am
Monday and the stop working time to 8pm Tuesday, use S1+1=8, S3+1=24, S1+2 =24 and S3+2=20. See the formula
in the following table.
_6 Day Start Hour Start Minute Stop Hour Stop Minute
Sunday S1 24 S2 00 S3 24 S4 00
Monday S1+1 08 S2+1 00 S3+1 24 S4+1 00
Tuesday S1+2 24 S2+2 00 S3+2 20 S4+2 00
8. This instruction should work with the real-time clock in the PLC. Before operating, make sure the PLC battery is
securely installed and working correctly.
9. There is no limit on the number of times you can execute the instruction but the output control device D cannot be
used repeatedly. If you use the device D repeatedly, only the last output result from the WWON instruction is executed.
10. If more than 1 set of work hours are needed, use the WWON instruction repeatedly as required. Note that you cannot
use the output control device D repeatedly.
6-590
Example 1
Set a working time from 8:00 to 18:00 from Monday to Friday and no work on Saturday and Sunday.
The following table lists the settings for the device D.
Sunday D0 24 D10 00 D20 24 D30 00
Monday D1 08 D11 00 D21 18 D31 00
Tuesday D2 08 D12 00 D22 18 D32 00
Wednesday D3 08 D13 00 D23 18 D33 00
Thursday D4 08 D14 00 D24 18 D34 00
Friday D5 08 D15 00 D25 18 D35 00
Saturday D6 24 D16 00 D26 24 D36 00

6_
When M0 is ON, Y0.0 is ON from 8:00 to 18:00 from Monday to Friday; for other times the Y0.0 is OFF.
Example 2
Set a working time from 18:00 Monday to 08:00 Tuesday and from 18:00 Tuesday to 08: 00 Wednesday. Follow this pattern
to 08:00 Saturday and no work on Sunday.
6-591
The following table lists the settings for the device D.
Sunday D0 24 D10 00 D20 24 D30 00
Monday D1 18 D11 00 D21 08 D31 00
Tuesday D2 18 D12 00 D22 08 D32 00
Wednesday D3 18 D13 00 D23 08 D33 00
Thursday D4 18 D14 00 D24 08 D34 00
Friday D5 18 D15 00 D25 08 D35 00
Saturday D6 24 D16 00 D26 24 D36 00
When M0 is ON, Y0.0 is ON from 18:00 to 8:00 the next day from Monday to Friday and for other times the Y0.0 is OFF.
Example 3
Set a working time from 08:00 to 12:00 and from 14:00 to 17:30 from Monday to Friday. No work on Saturday and Sunday.
_6
6-592
The following table lists the settings in the morning for the device D.
Sunday D0 24 D10 00 D20 24 D30 00
Monday D1 08 D11 00 D21 12 D31 00
Tuesday D2 08 D12 00 D22 12 D32 00
Wednesday D3 08 D13 00 D23 12 D33 00
Thursday D4 08 D14 00 D24 12 D34 00
Friday D5 08 D15 00 D25 12 D35 00
Saturday D6 24 D16 00 D26 24 D36 00
The following table lists the settings in the afternoon for the device D.
Sunday D40 24 D50 00 D60 24 D70 00
Monday D41 14 D51 00 D61 17 D71 30
Tuesday D42 14 D52 00 D62 17 D72 30

6_
Wednesday D43 14 D53 00 D63 17 D73 30
Thursday D44 14 D54 00 D64 17 D74 30
Friday D45 14 D55 00 D65 17 D75 30
Saturday D46 24 D56 00 D66 24 D76 00
When M0 is ON, Y0.0 is ON from 08:00 to 12:00 and 14:00 to 17:30 from Monday to Friday and for other times the Y0.0 is
OFF.
6-593
6.18 Peripheral Instructions

6.18.1 List of Peripheral Instructions
The following table lists the Peripheral instructions covered in this section.

API Function
1700 TKY DTKY – Ten-key keypad
1701 HKY DHKY – Sixteen-key keypad
1702 DSW – – DIP switch
1703 ARWS – – Arrow keys
1704 SEGL – – Seven-segment display with latches
_6
6-594
6.18.2 Explanation of Peripheral Instructions
1700 D TKY S, D1, D2 Ten-key keypad

S 
D1    
D2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D1    
D2 

- AS AS
Symbol
S ： First input device

Device where the value is
D1 ：
stored
D2 ： Output signal
Explanation 6_
1. The ten external inputs starting from the input specified by S represents 0–9 in the decimal system. They are
connected to ten keys. You can enter a four-digit decimal value 0–9,999 (16-bit instruction) or an eight-digit
decimal value 0–99,999,999 (32-bit instruction) by pressing the keys in order. The instruction stores the decimal
value in D1, and stores the output signals in D2.
2. The operand S occupies ten bits.
3. The operand D2 occupies eleven bits. Please do not change the states of the bits during the execution of the
instruction.
4. When the conditional contact is not enabled, the eleven bits starting from the bit specified by D2 are OFF.
5. When using on-line editing, please reset the conditional contact to initialize the instruction.
6. You can use the 32-bit counter only when D1 uses 32-bit instructions.
6-595
Example
1. The ten external inputs starting from X0.0 are connected to ten keys that represent 0–9 in the decimal system.
When M0 is ON, the instruction stores the value that you enter as a binary value in D0, and stores the output
signals in M10–M19.
0 1 2 3 4 5 6 7 8 9
24VDC
X0.0 X0.1 X0.2 X0.3 X0.4 X0.5 X0.6 X0.7 X0.8 X0.9 S/S
Note: The digital input module AH16AM10N-5A is used in this example.
_6 0 1 2 3 4 5 6 7 8 9 Numeric keys
Binary -coded One- di gi t binary- coded

decimal value decimal code
Ov erflowi ng 10
3 2
10 10
1
10
0
Binary -coded
decimal value
Binary
value D0
2. If the keys connected to X0.5, X0.3, X0.0, and X0.1 are pressed in the order shown in the timing chart, the
instruction stores the result 5,301 in D0. The maximum value that can be stored in D0 is 9,999. If the value
exceeds four digits, the first digit from the left overflows.
3. After the key connected to the X0.2 is pressed and before other keys are pressed, M12 is ON. The same applies to
the other keys.
6-596
4. When a key connected to the input within the range between X0.0 and X0.9 is pressed, the corresponding output
within the range between M10 and M19 is ON.
5. When one of the keys is pressed, M20 is ON.
6. When the conditional contact M0 is switched OFF, the value stored in D0 is unchanged; however, M10–M20 are
switched OFF.
X0.0 3
X0.1 4
X0.3 2
X0.5 1
M10
M11
M13
M15
Output si gnal
M20 1 2 3 4 6_
Additional remarks
2. If you declare the operand D2 in ISPSoft, the data type is ARRAY [11] of BOOL.
6-597
1701 D HKY S1, S2, D1, D2, D3 Sixteen-key keypad

S1 
S2 
D1 
D2    
D3    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1 
S2  
D1 
D2    
D3 

- AS AS
Symbol
S1 ： First input device
S2 ： For system use only

_6 D1 ： First output device
D2 ： Device where the value is stored
D3 ： Output signal
Explanation
1. The four external inputs starting from the input specified by S are connected to the four external outputs starting
from the output specified by D1 to form a 16-key keypad. The instruction stores the value that you enter by
pressing the keys in D2, and stores the output signals in D3. If you press several keys simultaneously, the value
that is smaller is stored.
2. The value that you enter by pressing the keys is temporarily stored in D2. For the 16-bit HKY instruction, the
maximum value that can be stored in D2 is 9,999. If the value exceeds four digits, the first digit from the left
overflows. For the 32-bit DHKY instruction, the maximum value that can be stored in D2 is 9,999. If the value
exceeds eight digits, the first digit from the left overflows.
3. After the instruction completes, SM692 is ON. That is, SM692 is ON for a scan cycle after the execution of the
matrix scan is complete.
6-598
4. You can use the 32-bit counter only when D2 uses 32-bit instructions.
Example
1. The four external inputs X0.0–X0.3 are connected to the four external outputs Y0.0–Y0.3 to form a 16-key keypad.
When X1.0 is ON, the instruction stores the value that you enter as a binary value in D0, and stores the output
signals in M0–M7.
The function of SM691:
 If SM691 is ON, the 16-bit instruction takes 0–F as hexadecimal values.
 Numeric keys:
0 1 2 3 4 5 6 7 8 9 A B C D E F Kyes
Ov erflowi ng 16
3
16
2 1
16 16
0
6_
D0
 If SM691 is OFF, the 16-bit instruction takes A–F as function keys.
 Numeric keys:
0 1 2 3 4 5 6 7 8 9 Numeric keys
Bina ry -c oded One- di gi t binary- coded

dec imal v alue
decimal code
Ov erflowi ng 10
3
10
2
10
1
10
0
Bina ry -c oded
dec imal v alue
Binary
D0
value
6-599
 Function keys:
 When A is pressed, M0 stays ON. When D is pressed, M0 switches OFF, and M3 stays ON.
 If several function keys are pressed, the key which is pressed first has priority.
F E D C B A
M5 M4 M3 M2 M1 M0
2. Output signals:
 When a key within the range between A and F is pressed, M6 is ON.
 When a key within the range between 0 and 9 is pressed, M7 is ON.
3. When the conditional contact X1.0 switches to OFF, the value that was stored in D0 is unchanged. However, M0–
M7 are switched OFF.
4. The external wiring:
C D E F
8 9 A B
_6
4 5 6 7
0 1 2 3
24VDC
+
X0.0 X0.1 X0.2 X0.3 S/S Y0.0 Y0.1 Y0.2 Y0.3 UP ZP
Note: The transistor output module AH16AP11T-5A is used in this example.
Additional remarks
1. When this instruction is executed, a too long or a too short scan cycle time will cause the state of the switches to
be read incorrectly. Use the following tips to solve the issue.
 When the scan cycle is too short, the I/O may not be able to respond in time and cannot read the correct
states of the inputs. You can set a fixed scan time to solve this issue.
 When the scan cycle is too long, the switch may become slow to react. You can write this instruction to a
timer interrupt task to set a fixed time to execute this instruction.
6-600
1702 DSW S1, S2, D1, D2, n DIP switch

S1 
S2 
D1 
D2   
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D1 
D2  
n  

- AS -
Symbol
D1 ： First output device 6_

D2 ： Device where the value is stored
n ： Number of DIP switches
Explanation
1. The four or eight external inputs starting from the input specified by S1 are connected to the four external outputs
starting from the output specified by D1 to form a four-digit DIP switch or two four-digit DIP switches. The
instruction stores the value from the DIP switch in D2. Whether there is one four-digit DIP switch or two four-digit
DIP switches depends on n.
2. If n is 1, the operand D2 occupies one register. If n is 2, the operand D2 occupies two registers.
3. S2 and S2+1, are for system use only, and occupy two devices. Please do not alter the values in these devices.
4. After the instruction completes, SM694 is ON for a scan cycle.
5. When the conditional contact is not enabled, the four external outputs starting from the output specified by D1 stay
OFF.
6-601
Example
1. X0.0–X0.3 are connected to Y0.0–Y0.3 to form the first DIP switch, and X0.4–X0.7 are connected to Y0.0–Y0.3 to
form the second DIP switch. When X1.0 is ON, the instruction converts the value that you enter with the first DIP
switch into the binary value, and stores the conversion result in D20. The instruction converts the value that you
enter with the second DIP switch into the binary value, and stores the conversion result in D21.
2. When X1.0 is ON, Y0.0–Y0.3 are ON cyclically. After the instruction completes, SM694 is ON for a scan cycle.
3. The following graphic shows the outputs. Y0.0–Y0.3 must be transistors.
X1.0
Cycli c ac tion
Y0.0 0.1s 0.1s 0.1s
Y0.1 0.1s
Inter ruption
Y0.2 0.1s
_6 Y0.3 0.1s
T he execution of the
SM694 insturc iton is complete.
4. The following graphic shows the DIP switches.
0 1 2 3
10 10 10 10
Bina ry - cod ed d ecim al

wirin g of D IP sw itch es
A dio de (1 N4 14 8) m u st
b e con ne cted i n series .
+
3 2 1 0
1 2 4 8 1 2 4 8 10 10 10 10
X 0 .0 X 0.1 X 0 .2 X 0 .3 X 0. 4 X 0.5 X 0.6 X0 .7 S /S Y 0.3 Y 0.2 Y 0.1 Y0 .0 UP ZP
F irst D IP sw itch S eco nd D IP sw tich
N o te : Th e tra nsist or o ut pu t mo du le AH 16 AP11 T-5 A is use d in th is exam ple .
6-602
Additional remarks
1. If n exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
6_
6-603
1703 ARWS S1, S2, D1, D2, n Arrow keys

S1 
S2 
D1   
D2 
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1 
S2  
D1  
D2 
n  

- AS -
Symbol

_6 D1 ： Device where the setting value is stored
D2 ： First output device
n ： Positive/Negative logic
Explanation
1. This instruction defines S1 as the down arrow, S1+1 as the up arrow, S1+2 as the right arrow, and S1+3 as the left
arrow. The instruction stores the setting value in D1, and the value must be between 0–9,999.
2. The operand S1 occupies four consecutive bit devices.
3. S2 is for system use only. Please do not alter the value in it.
4. The operand D2 occupies eight consecutive bit devices.
5. When the conditional contact is disabled, the eight bit devices starting from the bit device specified by D2 stay OFF.
6-604
Example
1. The instruction defines X0.0 as the down arrow, X0.1 as the up arrow, X0.2 as the right arrow, and X0.3 as the left
arrow. The instruction stores the setting value in D20, and the setting value must be between 0–9,999.
2. When X1.0 is ON, the digit in the place 103 is selected. If the left arrow is pressed, the places are selected in
sequence (103→100→101→102→103→100).
3. If you press right arrow, the places are selected in sequence (103→102→101→100→103→102). The LED indicators
for the corresponding places are connected to Y0.4–Y0.7. When the digits in the places are selected in sequence,
the LED indicators are ON in sequence.
4. If you press the up arrow, the digit in the place selected changes (0→1→2→…8→9→0→1). If you press the down
arrow, the digit in the place selected changes (0→9→8→…1→0→9). The new digit is shown on seven-segment
display.
Up arr ow
Y 0.4
Y0 .5
Y 0.6
X 0.1 6_
Y 0.7 LED indic ators
Left arrow X 0.3 X 0.2 Right arr ow
3 2 1 0
10 10 10 10
1 X 0.0
Y 0.0
2
Y 0.1
4
Y 0.2
Y 0.3
8 Down arrow
T he four key s ar e used to select

Four -digit sev en- segment display the place and change the digit
Additional remarks
1. If n exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
2. If you declare the operand S1 in ISPSoft, the data type is ARRAY [4] of BOOL.
3. If you declare the operand D2 in ISPSoft, the data type is ARRAY [8] of BOOLL.
6-605
1704 SEGL S1, S2, D, n Seven-segment display with latches

S1        
S2 
D 
n        
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D 
n  

- AS -
Symbol
S1 ： Source device
D ： First output device
_6 n ： Positive/Negative logic
Explanation
1. The eight external outputs starting from the output specified by D are connected to a four-digit seven-segment
display; or the twelve external outputs starting from the output specified by D are connected to two four-digit seven-
segment displays. Every place is equipped with a driver that converts a binary-coded decimal value into seven-
segment data, and every driver is equipped with a latch that can be used to store state information.
2. The value in S1 is the value to show on first seven-segment display, and the value in S1+1 is the value to show on
second seven-segment display.
3. S2 is for system use only. Please do not alter the value in it.
4. The operand n must be between 0–7. Please refer to the Additional remark for more information.
5. Whether there is one four-digit seven-segment display or two four-digit seven-segment displays, and whether an
output is a positive logic output or a negative logic output depends on n.
6. If there is one four-digit seven-segment display, eight outputs are occupied. If there are two four-digit seven-
segment displays, twelve outputs are occupied.
6-606
7. When the instruction is executed, the outputs are ON cyclically. If the conditional contact switches from OFF to ON
during the execution of the instruction, the outputs are ON cyclically again.
8. After the execution of the instruction is complete, SM693 is ON for a scan cycle.
Example
1. When X1.0 is ON, the instruction is executed. Y0.0–Y0.4 form a circuit. The instruction converts the value in D10
into the binary-coded decimal value, and shows the conversion result on first seven-segment display. The
instruction converts the value in D11 into the binary-coded decimal value, and shows the conversion result on
second seven-segment display. If the value in D10 or D11 exceeds 9,999, an operation error occurs.
2. When X1.0 is ON, Y0.4–Y0.7 are ON cyclically. It takes twelve scan cycles for Y0.4–Y0.7 to be ON. After the
instruction completes, SM693 is ON for a scan cycle.
3. If there is one four-digit seven-segment display, n is between 0–3.
 Connect the pins 1, 2, 4, and 8 in parallel, then connect them to Y0.0–Y0.3 on the PLC, and connect the 6_
latches to Y0.4–Y0.7 on the PLC.
 When X1.0 is ON, the instruction is executed. Y0.4–Y0.7 are ON cyclically, and the value in D10 is shown on
seven-segment display.
4. If there are two four-digit seven-segment displays, n is between 4–7.
 Connect the pins 1, 2, 4, and 8 in parallel, then connect them to Y0.8–Y0.11 on the PLC, and connect the
latches to Y0.4–Y0.7 on the PLC.
 The value in D10 is shown on first seven-segment display, and the value in D11 is shown on second seven-
segment display. If the values in D10 and D11 are 1234 and 4321 respectively, 1234 is shown on second
seven-segment display.
6-607
5. The wiring:
Y0.0 Y0.1 Y0.2 Y0.3 Y0.4 Y0.5 Y0.6 Y0.7 Y0.8 Y0.9 Y0.10 Y0.11 UP ZP
0 1 2 3
1 2 4 8 +
10 10 10 10
24VDC
3 2 1 0 3 2 1 0
10 10 10 10 10 10 10 10
1
2 V+ 1
2 V+
4 4
8 8
First 7-segment display Second 7-segment display
Note: The transistor output module AH16AN01T-5A is used in this example.
Additional remarks
 Whether an output is a positive output or a negative output, and whether there is one four-digit seven-
segment display or two four-digit seven-segment displays depend on n.
 The outputs on the PLC should be NPN transistors whose collectors are open collectors. In addition, an
output has to connect a pull-up resistor to the DC power supply (less than 30 VDC). Therefore, when an
output is ON, a signal of low potential is output.
 The following table shows the negative logic.
_6 Output
Binary-coded
(Binary-coded Signal
decimal value
decimal code)
b3 b2 b1 b0 8 4 2 1 A B C D
0 0 0 0 0 0 0 0 1 1 1 1
0 0 0 1 0 0 0 1 1 1 1 0
0 0 1 0 0 0 1 0 1 1 0 1
0 0 1 1 0 0 1 1 1 1 0 0
0 1 0 0 0 1 0 0 1 0 1 1
0 1 0 1 0 1 0 1 1 0 1 0
0 1 1 0 0 1 1 0 1 0 0 1
0 1 1 1 0 1 1 1 1 0 0 0
1 0 0 0 1 0 0 0 0 1 1 1
1 0 0 1 1 0 0 1 0 1 1 0
6-608
 The following table shows the positive logic.
Output
Binary-coded
(Binary-coded Signal
decimal value
decimal code)
b3 b2 b1 b0 8 4 2 1 A B C D
0 0 0 0 1 1 1 1 0 0 0 0
0 0 0 1 1 1 1 0 0 0 0 1
0 0 1 0 1 1 0 1 0 0 1 0
0 0 1 1 1 1 0 0 0 0 1 1
0 1 0 0 1 0 1 1 0 1 0 0
0 1 0 1 1 0 1 0 0 1 0 1
0 1 1 0 1 0 0 1 0 1 1 0
0 1 1 1 1 0 0 0 0 1 1 1
1 0 0 0 0 1 1 1 1 0 0 0
1 0 0 1 0 1 1 0 1 0 0 1
 The following table shows the latch.
Positive logic Negative logic

Latch Signal Latch Signal
1 0 0 1
6_
 The following table shows the setting value of the parameter n.
Number of seven-
One Two
segment displays
Output
(Binary-coded ＋－＋－
decimal code)
Latch ＋－＋－＋－＋－
n 0 1 2 3 4 5 6 7
‘＋’: Positive logic
‘－’: Negative logic
 You can edit the parameters in n to modify the logics for the output transistor and the input of the seven-
segment display.
6-609
 The following graphic shows the connection of the common-anode four-digit seven-segment display with IC
7447.
3 2 1 0
8 4 2 1 10 10 10 10
1K 120
B Vcc
C f
LT g 3 a f 2 1 b
+
5VDC RBO a
RBI b e d c h g 0
D c
A d
GND e
IC7447
C0
_6
6-610
6.19 Communication Instructions

6.19.1 List of Communication Instructions
The following table lists the Communication instructions covered in this section.

API Function
1806 LRC – – Longitudinal parity check
1807 CRC – – Cyclic Redundancy Check
1808 MODRW – – Reading and Writing Modbus data
1812 COMRS – – Sending and receiving communication data
Setting the communication format for a serial communication

1813 COMDF – 
port
Serial communication instruction exclusively for Delta AC

1814 VFDRW – –
motor drives
Serial communication instruction exclusively for Delta servo

1815 ASDRW – –
drives
Setting the parameters in the data exchange table for a

1816 CCONF – 
communication port
1817 MODRWE – – Reading and writing Modbus data without using any flags 6_
1818 DNETRW – – Reading and writing DeviceNet communication data
1819 CANRS – – User-defined CAN communication sending and receiving
1820 DMVSH – – Enabling Delta DMV detection and communication
Execute the appointed communication number of the data

1821 DESO – –
exchange table once
6 - 6 11
6.19.2 Explanation of Communication Instructions

1806 LRC S, n, D Longitudinal parity check

S  
n    
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

- AS -
Symbol
S ： First device to which the LRC is applied
n ： Number of bytes
First device where the operation result is
D ：
stored
_6 Explanation
1. This instruction performs a longitudinal parity check on n bytes in the device specified by S. Please refer to the
Additional remark for this instruction (below) for more information about the LRC check code.
2. The operand n must be an even number, and must be between 1–1000. If n is not in the range, an operation error
occurs, the instruction is not executed, SM0 and SM1 are ON, and the error code in SR0 is 16#200B.
3. The 16-bit conversion mode: When SM606 is OFF, the instruction divides the hexadecimal data in the device
specified by S into the high 8-bit data and the low 8-bit data. The instruction applies the LRC to every byte, and
stores the operation result in the high 8-bit and the low 8-bit in the device specified by D. The number of bytes
depends on n.
4. The 8-bit conversion mode: When SM606 is ON, the instruction divides the hexadecimal data in the device
specified by S into the high 8-bit data (invalid data) and the low 8-bit data. The instruction applies the LRC to every
byte, and stores the operation result in the low 8-bit in the two registers. The number of bytes depends on n. The
values of the high 8 bits in the two registers are 0.
6-612
Example
1. The PLC is connected to the VFD-S series AC motor drive (ASCII modeSM210 is OFF; 8-bit mode: SM606 is ON.).
The PLC sends the command, and reads the data in the six devices at the addresses starting from 16#2101 in the
VFD-S series AC motor drive.
PLCVFD-S
The PLC sends “：01 03 2101 0006 D4 CR LF”.
The PLC sends the data in the following table.
Register Data Description

D100
Low 8 bits ‘：’ 16#3A STX
D101
‘0’ 16#30 ADR 1 AD (1, 0) is the station address of the AC motor
Low 8 bits
D102 drive.
‘1’ 16#31 ADR 0
Low 8 bits
D103
Low 8 bits ‘0’ 16#30 CMD 1
CMD (10) is the command code.
D104
‘3’ 16#33 CMD 0
Low 8 bits
D105
‘2’ 16#32
Low 8 bits
D106
Low 8 bits ‘1’ 16#31
Initial data address
D107
‘0’ 16#30 6_
Low 8 bits
D108
‘1’ 16#31
Low 8 bits
D109
Low 8 bits ‘0’ 16#30
D110
‘0’ 16#30
Low 8 bits
Number of data (counted by the word)
D111
‘0’ 16#30
Low 8 bits
D112
Low 8 bits ‘6’ 16#36
D113
‘D’ 16#44 LRC CHK 0
Low 8 bits
LRC CHK (01) is the error checking code.
D114
Low 8 bits ‘4’ 16#34 LRC CHK 1
D115
Low 8 bits CR 16#0D
END
D116
LF 16#0A
Low 8 bits
LRC CHK (01) above is the error checking code. You can use the LRC instruction to calculate it (8-bit mode:
SM606 is ON).
6-613
LRC check code: 16#01+16#03+16#21+16#01+16#00+16#06=16#2C
The two’s complement of 16#2C is 16#D4. ‘D’ (16#44) is stored in the low 8-bit in D113, and ‘4’
(16#34) is stored in the low 8-bit in D114.
Additional remarks
1. The following table lists the format of the communication data in the ASCII mode.
STX ‘：’ The start-of-text character is ‘：’ (16#3A).
Address Hi ‘0’ Communication address:
Address Lo ‘1’ The 8-bit address is composed of two ASCII codes.
Function Hi ‘0’ Function code:
Function Lo ‘3’ The 8-bit function code is composed of two ASCII codes.
‘2’ Data: The n×8-bit data is composed of 2n ASCII codes.
‘1’
_6 ‘0’
DATA（n-1）
‘2’
…….
‘0’
DATA 0
‘0’
‘0’
‘2’
LRC CHK Hi ‘D’ LRC check code:
LRC CHK Lo ‘7’ The 8-bit check code is composed of two ASCII codes.
END Hi CR End-of-text character:
END Lo LF END Hi=CR (16#0D), END Lo=LF (16#0A)
2. LRC check code: The instruction adds up the values starting from the communication address to the data, then the
instruction calculates the two’s complement of the sum that is the LRC check code.
Example 16#01+16#03+16#21+16#02+16#00+16#02=16#29
The two’s complement of 16#29 is 16#D7.
6-614
1807 CRC S, n, D Cyclic Redundancy Check

S  
n    
D DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  
n  
D  

- AS -
Symbol
S ： First device to which the CRC is applied
n ： Number of bytes
First device in which the operation result is
D：
stored
Explanation
1. This instruction performs a cyclic redundancy check on n bytes starting with the device specified by S. Please refer 6_
to the Additional remark for this instruction (below) for more information about the CRC check code.
2. The operand n must be between 1–1000. If n is not in the range, an operation error occurs, the instruction is not
executed, SM0 and SM1 are ON, and the error code in SR0 is 16#200B.
3. The 16-bit conversion mode: When SM606 is OFF, the instruction divides the hexadecimal data in the device
specified by S into the high 8-bit data and the low 8-bit data. The instruction applies the CRC to every byte, and the
stores the operation result in the high 8-bit and the low 8-bit in the device specified by D. The number of bytes
depends on n.
4. The 8-bit conversion mode: When SM606 is ON, the instruction divides the hexadecimal data in the device
specified by S into the high 8-bit data (invalid data) and the low 8-bit data. The instruction applies the CRC to every
byte, and stores the operation result in the low 8-bit in the two registers. The number of bytes depends on n.
6-615
Example
1. The PLC is connected to the VFD-S series AC motor drive (RTU modeSM210 is ON; 16-bit mode: SM606 is ON.).
The value 16#12, to be written into the device at 16#2000 in the VFD-S series AC motor drive, is written into the
device in the PLC first.
PLCVFD-S
The PLC sends 01 06 2000 0012 02 07.
The PLC sends the data in the following table.
Register Data Description
D100
16#01 Address
Low 8 bits
D101
16#06 Function
Low 8 bits
D102
16#20
Low 8 bits
Data address
D103
16#00
Low 8 bits
_6 D104
16#00
Low 8 bits
Data
D105
16#12
Low 8 bits
D106
16#02 CRC CHK 0
Low 8 bits
D107
16#07 CRC CHK 1
Low 8 bits
CRC CHK (01) above is the error checking code. You can calculate it with the CRC instruction (8-bit mode: SM606
is ON).
CRC check code: 16#02 is stored in the low 8-bit in D106, and 16#07 is stored in the low 8-bit in D107.
6-616
Additional remarks
1. The following table shows the format of the communication data in RTU mode.
START Time interval
Address Communication address: 8-bit binary address
Function Function code: 8-bit binary code
DATA（n-1） Data: n×8-bit data
…….
DATA 0
CRC check code:

CRC CHK Low
The 16-bit check code is composed of two 8-bit binary codes.
CRC CHK High
END Time interval
2. CRC check code: The check code starts from the address to the data. The operation rule is shown in the following
table.
Step 1: Suppose the data in the 16-bit register (the register where the CRC check code is stored) is 16#FFFF.
Step 2: The logical operator XOR takes the first 8-bit message and the low 8-bit data in the 16-bit register, and
6_
performs the logical exclusive OR operation on each pair of corresponding bits. The operation result is
stored in the 16-bit register.
Step 3: The values of the bits in the 16-bit registers are shifted by one bit to the right. The value of the highest
bit becomes 0.
Step 4: If the value of the right-most bit that is shifted to the right is 0, the data from step 3 is stored in the 16-bit
register. Otherwise, the logical operator XOR takes 16#A001 and the data in the 16-bit register, and
performs the logical exclusive OR operation on each pair of corresponding bits. The operation result is
stored in the 16-bit register.
Step 5: Repeat step 3 and step 4, and perform the operation on the 8-bit message.
Step 6: Repeat step 2–5, and then get the next 8-bit message. Perform the operations on all messages. The
final result in the 16-bit register is the CRC check code. Notice that the low 8-bit data in the 16-bit
register is interchanged with the high 8-bit data in the 16-bit register before the CRC check code is put
into the check code of the message.
6-617
1808 MODRW S1, S2, S3, S, n Reading and Writing Modbus data

S1    
S2    
S3    
S 
n    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1  
S2  
S3  
S   
n  

- AS -
Symbol
S1 ： Unit address
S2 ： Function code
_6
S3 ： Device address
S ： Register for reading/writing the data
n ： Data length
Explanation
1. The operand S1 must be between 0–254; 0 is the broadcasting mode.
2. S2 is the function code.
The following table shows an example.
Function Data
Description Devices that support devices for slaves
code length
16#01 PLC reads the data from several bit devices. 1-1600 X, Y, M, SM, S, T, C, HC
16#02 PLC reads the data from several bit devices. 1-1600 X, Y, M, SM, S, T, C, HC
PLC reads the data from several word

16#03 1-100 X, Y, SR, D, T, C, HC, E
devices.
6-618
Function Data
Description Devices that support devices for slaves
code length
PLC reads the data from several word

16#04 1-100 X
devices.
16#05 PLC writes the state into a bit device. 1 Y, M, SM, S, T, C, HC
16#06 PLC writes the data into a word device. 1 Y, SR, D, T, C, HC, E
16#0F PLC writes the states into several bit devices. 1-1600 Y, M, SM, S, T, C, HC
PLC writes the data into several word

16#10 1-100 Y, SR, D, T, C, HC, E
devices.
The instruction supports only the function codes mentioned above, and cannot execute other function codes.
Please refer to the examples below.
3. S3 is the device address. If the address is invalid for the designated communication device, the communication
device responds with an error message. For example, the device address 16#8000 is invalid in the DVP-ES2.
4. S is the register involved in the reading/writing the data.
The data to be written into the external equipment is stored in the register in advance.
The data to be read from the external equipment is stored in the register.
5. N is the length of the data
For word-type communication function codes, the data length cannot exceed 100 words.
6_
For bit-type (BOOL) communication function codes, the data length is between 1–1600 bits.
6. The following table shows how the functions of S3, S, and n vary with the function code used.
Function
S3 S n
code
Address from where the Register where the

16#01 Length of data read
data is read data read is stored



16#05 Address into where the Status value written No meaning
6-619
Function
S3 S n
code
data is written
Address into where the Register where the

16#06 No meaning
data is written data written is stored

16#0F Length of data written

16#10 Length of data written
7. There is no limitation on the number of times you can use this instruction; however only one instruction can be
executed on the same COM port at a time. You need to decide and use the sending flag for the COM to be used
before executing this instruction. Otherwise, the data from 2 different communication COMs may be mixed up.
8. If a communication timeout occurs, the timeout flags are ON. After you solve the problem, you must reset timeout
flags to OFF. When using this instruction, the timeout value cannot 0. Set the value between 100–32767ms; when
the value is set to 0, it is processed as 200 ms.
9. In Modbus ASCII mode, you need to set up only the data (non-ASCII mode) for transmission. The instruction converts
the non-ASCII mode to the ASCII mode, consisting of the head code (:), the converted ASCII code, checksum (LRC)
and tail code (CRLF). The instruction stores the data received in ASCII character in the internal register. The PLC
_6 automatically converts the data into the hexadecimal value, and if the communication data is correct, stores the
conversion result in S. and sets the completion flag SM to ON.
10. In Modbus RTU mode, you need to set up only the data for transmission. The instruction adds the checksum (CRC)
and the stores the data received in ASCII character in the internal register. The PLC automatically converts the data
into the hexadecimal value, and if the communication data is correct, stores the conversion result stored in S.
11. The instruction cannot be used in the ST programming language, interrupt tasks or function block which is called
only once.
Communication protocol setup example
1. The following examples use PLC communication port 1 and special registers to demonstrate how to setup a
communication protocol.
2. You can set up the PLC communication port with HWCONFIG in ISPSoft, or with the relative special registers, or
you can use the COMDF instruction (API 1813) to set up the communication. Please refer to the ISPSoft manual for
setting it up in HWCONFIG. For communication register setups (SM, SR), please refer to section 6.19.3 for more
details.
6-620
3. The communication setup for this example is RS485 ASCII, 9600, 8, E, 1 (SR209=16#0025).
4. Set the communication timeout to 3000ms (SR210=3000).
5. Set the communication mode to ASCII mode (SM210=OFF).
6. Enable the communication protocol (SM209=ON).
If you set up the communication port with the COMDF instruction (API 1813), you can ignore this step.
6_
If you set up the communication port in ISPSoft－＞HWCONFIG－＞COM Port, you can ignore this step.
6-621
Example 1
1. Function code 01 (16#01): the PLC reads the data from several bit devices that are not discrete input devices (16
pieces of data is read in this example). For function code 02, the operation is the same as for function code 01.
AS Series CPU module is connected to the DVP-ES2 Series PLC.
When SM96 and X0.0 are on, the AS Series CPU sends and receives the Y0–Y17 commands from the DVP-ES2.
When the address of Y0 is 16#0500, the states of Y0–Y17 in DVP-ES2 are listed in the following table.
_6 Device Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
State ON ON OFF ON OFF OFF ON OFF
Value D 2
Device Y17 Y16 Y15 Y14 Y13 Y12 Y11 Y10
State OFF OFF OFF OFF OFF ON OFF OFF
Value 0 4
The following table lists the operands for the MODRW instruction.
Operand Description Device
S1 Unit address 16#0001
S2 Function code 16#0001
S3 Device address 16#0500
S Register for reading and writing the data D10.0
n Data length 16
6-622
ASCII mode
You do not need to convert the ASCII codes and they are all expressed in 16# values.
 AS sends the communication command: “：01 01 05 00 00 10 E9 CR LF”.
 AS receives the communication command: “：01 01 02 D2 04 26 CR LF”.
RTU mode
 AS sends the communication command: “01 01 05 00 00 10 3D 0A”.
 AS receives the communication command: “01 01 02 D2 04 E4 9F”.
If the format is correct, SM100 is ON.
2. The response messages from the DVP-ES2 are stored in registers D10.0 to 10.15 (the data read is D10.15–
D10.0=16#04D2).
Device D10.7 D10.6 D10.5 D10.4 D10.3 D10.2 D10.1 D10.0
Value D 2
Device D10.15 D10.14 D10.13 D10.12 D10.11 D10.10 D10.9 D10.8
Value 0 4 6_
3. After the receiving the data sent back from the DVP-ES2, the PLC confirms the data format sent back from DVP-
ES2 and determines if it is correct. If no error occurs in the format, the corresponding special flags SM100 are ON;
if not SM102 is ON.
6-623
Example 2
1. Function code 03 (16#03): the PLC reads the data from several bit devices that are not discrete input devices
(eight pieces of data is read in this example). For function code 04, the operation is the same as for function code
03.
2. AS Series CPU module is connected to the DVP-ES2 Series PLC.
When SM96 and X0.0 are on, the AS Series CPU module sends and receives D32–D39 from the DVP-ES2.
_6 3. When the address of D32 is 16#1020, the values of D32–D39 in DVP-ES2 are listed in the following table.
Device D32 D33 D34 D35 D36 D37 D38 D39
Value (16#) 1234 5678 1122 3344 5566 7788 99AA BBCC
The following table lists the operands of the MODRW instruction.
S3 Device address (D32) 16#1020
S Register involved for reading and writing the data D10
n Data length 8
6-624
ASCII mode
You do not need to convert the ASCII codes, and they are all expressed in 16# values.
 AS sends the communication command: “：01 03 10 20 00 08 C4 CR LF”.
 AS receives the communication command: “：01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC AA

CR LF”.
RTU mode
 AS sends the communication command: “01 03 10 20 00 08 41 06”.
 AS receives the communication command: “01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC 90 FE”.
 The response messages from the DVP-ES2 is stored in registers D10 to D17.
 The following table lists the values in D10–D17.
Device D10 D11 D12 D13 D14 D15 D16 D17
Value
1234 5678 1122 3344 5566 7788 99AA BBCC
(16#)
4. After the receiving the data sent back from the DVP-ES2, the PLC confirms the data format sent back from DVP-
if not SM102 is ON. 6_
6-625
Example 3
1. Function code 05 (16#05): the PLC writes the state into a bit device. The device is set to ON in this example.
_6
2. The AS Series CPU module is connected to the DVP-ES2 series PLC. D10.0 is ON and Y0 in the DVP-ES2 Series
PLC is also ON. When SM96 and X0.0 are ON, the PLC can set the state of Y0.
S1 Unit address 1
S3 Device address 16#0500
S Register for reading and writing the data D10.0
n Data length (not used with this function code) 1
ASCII mode
The numbers below are only for reference. Instead of showing the values in the ASCII codes, here the expressions
are shown in 16# values.
 AS sends the communication command: “：01 05 05 00 FF 00 F6 CR LF”
 AS receives the communication command: “：01 05 05 00 FF 00 F6 CR LF”
6-626
RTU mode
 AS sends the communication command: “01 05 05 00 FF 00 8C F6”
 AS receives the communication command: “01 05 05 00 FF 00 8C F6”
3. After receiving the data from the DVP-ES2, the PLC confirms the data format sent back from the DVP-ES2 and
determines if it is correct. If no error occurs in the format, the corresponding special flags SM100 are ON; if not
SM102 is ON.
4. When the DVP-ES2 receives this instruction, the Y0 is ON.
5. Since this function code writes data, the operand n is ignored.
6_
6-627
Example 4
1. Function code 06 (16#06): the PLC writes the state into a word device.
_6
2. AS Series CPU module is connected to the DVP-ES2 series PLC.
3. Suppose D10 is 16#55AA (waiting to write data to the device T0 of the DVP-ES2).
When SM96 and X0.0 are ON, the PLC can write data to the T0 of the DVP-ES2 series PLC. The address of T0 is
16#0600.
S1 Unit address 1
S3 Device address of T0 16#0600
S Register T0 for reading and writing the data D10
6-628
ASCII mode
 AS sends the communication command: “：01 06 06 00 55 AA F4 CR LF”
 AS receives the communication command: “：01 06 06 00 55 AA F4 CR LF”
RTU mode
 AS sends the communication command: “01 06 06 00 55 AA 36 6D”
 AS receives the communication command: “01 06 06 00 55 AA 36 6D”
4. After receiving the data from the DVP-ES2, the PLC confirms the data format sent back from the DVP-ES2 and
determines if it is correct. If no error occurs in the format, the corresponding special flags SM100 are ON; if not
SM102 is ON.
5. When the DVP-ES2 receives this instruction, it writes the data stored in the device D10 to the device T0 in the
DVP-ES2.
6_
6-629
Example 5
1. Function code 0F (16#0F): the PLC writes the states into several bit devices.
_6 2. AS Series CPU module is connected to the DVP-ES2 series PLC.
 Suppose D10.15-D10.0=16#04D2 (waiting to write the state of Y0-Y17 of the DVP-ES2)
Device D10.7 D10.6 D10.5 D10.4 D10.3 D10.2 D10.1 D10.0
Value D 2
Device D10.15 D10.14 D10.13 D10.12 D10.11 D10.10 D10.9 D10.8
Value 0 4
When SM96 and X0.0 are ON, the PLC can set the state of Y0-Y17 in the DVP-ES2. The address of Y0 is
16#0500.
6-630
S1 Unit address 1
S2 Function code 16#000F
S3 Device address of Y0 16#0500
S Registers Y0–Y17 for reading and writing the data D10.0
n Data length 16
ASCII mode
 AS sends the communication command: “：01 0F 0500 0010 02 D2 04 03 CR LF”
 AS receives the communication command: “：01 0F A0 00 00 10 40 CR LF”
RTU mode
 AS sends the communication command: “01 0F 05 00 00 10 02 D2 04 EA 43”
 AS receives the communication command: “01 0F A0 00 00 10 76 07”

6_
3. After receiving the data sent back from the DVP-ES2, the PLC confirms the data format sent back from the DVP-
if not SM102 is ON.
Device Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
Value D 2
Device Y17 Y16 Y15 Y14 Y13 Y12 Y11 Y10
Value 0 4
6-631
Example 6
1. Function code 10 (16#10): the PLC writes the states into several word devices.
2. AS Series CPU module is connected to the DVP-ES2 series PLC.
3. Suppose the values for D20–27 are listed in the following table (waiting to write data to the devices T0–7 of the
DVP-ES2).
_6 Device D20 D21 D22 D23 D24 D25 D26 D27
Value (16#) 1234 5678 1122 3344 5566 7788 99AA BBCC
When SM96 and X0.0 are ON, the PLC can write data to the T0–7 in the DVP-ES2 series PLC. The address of T0
is 16#0600.
The following table lists the operands of the MODRW instruction.
S1 Unit address 1
S3 Device address of T0 16#0600
S Register T0–7 for reading and writing the data D20
6-632
ASCII mode
 AS sends the communication command: “：01 10 0600 00 08 10 1234 5678 1122 3344 5566 7788 99AA BBCC
8F CR LF”
 AS receives the communication command: “：01 10 06 00 00 08 E1 CR LF”
RTU mode
 AS sends the communication command: “01 10 06 00 00 08 10 1234 5678 1122 3344 5566 7788 99AA BBCC 0B
0C”
 AS receives the communication command: “01 10 06 00 00 08 C1 47”
5. After receiving the data sent back from the DVP-ES2, the PLC confirms the data format sent back from the DVP-
ES2, and determines if it is correct. If no error occurs in the format, the corresponding special flags SM100 are ON;
if not SM102 is ON. When the DVP-ES2 receives this instruction, it writes data stored in the devices D20–27 to the
device T0–7 in the DVP-ES2.
Device T0 T1 T2 T3 T4 T5 T6 T7
Value (16#) 1234 5678 1122 3344 5566 7788 99AA BBCC
6_
Additional remarks
2. If the device specified by S is not sufficient to contain the n pieces of data, the instruction is not executed, SM0 is
3. If n exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
4. If the function code specified by S2 is related to bit devices, the device specified by S must be a bit device;
otherwise, an operation error occurs, the instruction is not executed, and the error code in SR0 is 16#2003.
5. If the function code specified by S2 is related to word devices, the device specified by S must be a word device;
otherwise, an operation error occurs, the instruction is not executed, and the error code in SR0 is 16#2003.
6-633
6. If the communication command is 0x05 or 0x06, the value in n can be ignored. The length of the data is only one
bit or one word.
7. The MODRW instruction is not executed if the sending flags SM96 and SM97 are not ON.
8. If a communication timeout occurs, the timeout flags SM104 and SM105 are ON, and the receiving flags SM98 and
SM99 are OFF.
9. If an error occurs while receiving data, the error flags SM102 and SM103 are ON, and the receiving flags SM98
and SM99 are OFF.
10. If the function code specified by S2 is related to word devices, the device in the external equipment with which the
PLC communicates must be a word device. If the function code specified by S2 is related to bit devices, the device
in the external equipment with which the PLC communicates must be a bit device.
11. Please refer to section 6.19.3 for more details on communication register setups (SM, SR).
_6
6-634
1812 COMRS S1, S2, S3, D1, D2 Sending and receiving communication data
S1    
S2  
S3    
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
D1  
D2  

- AS -
Symbol
S1 ：Communication port number (1–2, 11–12)

6_
S2 ：Source of the data to be sent
S3 ：Length of the data to be sent
D1 ：First device where communication data received is stored
D2 Condition for ending receiving data
Explanation
1. S1 is a communication port number: COM1 is number 1, COM 2 is number 2, Card 1 is number 11 and Card 2 is
number 12. If the data is out of the communication port range, the instruction does not execute any sending or
receiving.
2. If you use a specific character or characters to end receiving data, it is suggested that you apply the instruction to
ASCII data. If you do not apply the instruction to ASCII data, it is suggested that you use a timeout period to end
receiving data.
3. S2 is the source of the data to be sent.
S3 is the length of the data to be sent.
6-635
If S2 is D100 and S3 is 10, the instruction sends the values in the low bytes in D100–D109 through the
communication port specified by S1.
4. No strings are sent if the setting value in S3 is 0. The maximum number of characters that can be sent is 256
words.
5. D1 is the length of the data that is received.
D1+1–D1+n are the devices to store the data that is received
If D1 is D200, the value in D2 is 3, and the value in D2+1 is 16#0D0A, the instruction stores data received in the low
bytes in the devices starting from D201 (the high bytes is unchanged) The instruction continues to receive data
until it receives the consecutive stop characters 16#0D and 16#0A. The instruction writes the length of the data
received to D200 after receiving 16#0D and 16#0A, and sets a completion flag to ON after the receiving data
stops.
6. D2 is the mode for receiving data
D2+1 is the condition that ends receiving of data
D2 and D2+1 are described in the following table.
D2 Mode for receiving data Setting value in D2+1 Remark
After the sending of data is

Not receiving communication
_6 0 Unused complete, set a completion flag
data
to ON.
If the time that you set is

The setting value in D2+1 is
When the time after the last greater than 3000 milliseconds,
time. The unit of measurement
piece of data received exceeds the value in D2+1 is 3000. If the
1 is 1 millisecond. The setting
the time set in D2+1, the time that you set is less than 5
value in D2+1 is between 5–
receiving of data is complete. milliseconds, the value in D2+1
3000.
is 5.
The data received ends with a The setting value in D2+1 is a If a specific character is 16#0A,
2
specific character. specific character. the value in D2+1 is 16#000A.
The data received ends with If two specific characters are

The setting value in D2+1 is two
3 two consecutive specific 16#0D and 16#0A, the value in
specific characters.
characters. D2+1 is 16#0D0A.
The data received starts with a A specific character is stored in If a start character is 16#3A,
4 specific character. When the the high byte in D2+1, and the and time is 15 milliseconds, the
time after the last piece of data time is stored in the low byte in value in D2+1 is 16#3A0F.
6-636
is received exceeds the time D2+1. The time set in the low
set in D2+1, the receiving of byte in D2+1 is in the range of
data is complete. 5–255 milliseconds.
The data received starts with a The setting value in D2+1 is a If a start character is 16#3A,
5 specific character, and ends specific start character, and a and a stop character is 16#0A,
with a specific character. specific end character. the value in D2+1 is 16#3A0A.
The setting value in D2+1 is the

If you want to receive 10
A specific quantity of data is length of the data to receive.
6 characters, set the value in
received. The setting value is between 1–
D2+1 to 10.
256.
The data received ends with a
specific character and The setting value in D2+1 is a If an end character is 16#0A,
7
generates communication specific end character. the value in D2+1 is 16#000A.
interrupts.
Set the quantity of data The setting value in D2+1 is the If you want to receive 10
8 received and then generate length of the data received. The characters, set the value in
communication interrupts. setting value is between 1–256. D2+1 to 10.
A specific end character is

The data received ends with a
stored in the high byte in D2+1, If an end character is 16#0A,
specific character or a specific
6_
and the time is stored in the low and time is 15 milliseconds, the
9 quantity of data received; when
byte in D2+1. The time set in data length is 15 words, the
either condition is met, the
the low byte in D2+1 must be value in D2+1 is 16#0A0F.
transmission is complete.
between 1–255 milliseconds.
If the mode used is not
Others supported, the instruction is not
executed.
7. Except for mode 6 and 8, when data received in D2 exceeds the maximum range of the received data length (256
words) and no ending character is received, the instruction stops executing and treats this operation as a receiving
error. D1+0 is 0 and D1+1–D1+n do not store the received data.
8. The interactions among the communication port, the related special auxiliary relays, and the related special data
register are described in Section 6.19.3.
6-637
9. Timing diagrams
 Mode for receiving data: 0
When data is sent, you cannot cancel the sending of data. If the conditional contact preceding the instruction
is not enabled, the data will still be sent, but the completion flag will not be set to ON after sending of the data
is complete.
 Mode for receiving data: 1 or 4
Starting the ex ecution

of the ins truc ti on
Sending d ata
Reception fl ag
Rec eiving d ata
Completion fl ag
Comm uni cation

timeout fl ag
2 3 2 5
1 4 4 1
_6
Description:
① Start/stop the execution of the instruction.
② Time during which data is sent. The period of time in which data is sent is not measured.
③ After the first character is received, the time that passes before the next character is received is
measured. Whenever a character is received, the instruction clears the time measured. The completion
flag is not be set to ON until the time measured is greater than the setting value in D2+1.
④ If the instruction is still enabled after you reset the completion flag or the communication flag, the next
communication data is sent automatically when the instruction is scanned in the next cycle.
⑤ When the PLC begins to receive data, it begins to measure the time that passes. It does not set the
communication timeout to ON until the time measured exceeds the timeout period. It is suggested that
you set the timeout period to be longer than the time set in D2+1.
6-638
 Mode for receiving data: 2, 3, 5, 6, or 9.
Starting the ex ecution

of the ins truc ti on
Sending d ata
Reception fl ag
Rec eiving d ata
Completion fl ag
Comm uni cation

timeout fl ag
2 3 2 2
1 4 4 1
Description:
①  Start/stop the execution of the instruction.
②  Time during which data is sent. The period of time in which data is sent is not measured.
③  After the first character is received, the time that passes before the next character is
received is measured. Whenever a character is received, the instruction clears the time measured.
6_
The communication timeout flag is not set to ON until the time measured exceeds the
timeout period.
④  If the instruction is still enabled after you reset a completion flag or a communication flag,
the next communication data is sent automatically when the instruction is scanned in the
next cycle.
10. Mode for sending data / Mode for receiving data
8-bit mode: The command that is edited is stored in the initial transmission device, and the command to be sent
includes the head code and the tail code. The instruction divides the 16-bit data into the high 8-bit data and the low
8-bit data. The instruction ignores the high 8-bit data, and can send or receive the low 8-bit data can be sent or
received. Take standard Modbus for example.
Sending the data: (PLC→external equipment)
6-639
Receiving the data: (External equipment→PLC)
16-bit mode: The command that is edited is stored in the initial transmission device, and the command to be sent
includes the head code and the tail code. When SM106/SM107 is OFF, the instruction divides the 16-bit data into
the high 8-bit data and the low 8-bit data.
Sending the data: (PLC→external equipment)
Receiving the data: (External equipment→PLC)
_6
The data that the PLC receives from the external equipment includes the head and the tail code; therefore, you
have to be aware of the setting for the length.
11. When the mode is 7 or 8, the corresponding communication port and the interrupt number are listed in the
following table.
Communication
COM1 COM2 Card1 Card2
port number
Interruption number I300 I302 I304 I306
only once.
6-640
The following examples use COM1 (RS485).
Example 1
The mode in D2 is 0 (not receiving communication data) and you set the mode for sending and receiving data to 8-bit
mode (SM106=ON).
1. The length for the data to be sent: D20=4.
2. The contents for the data to be sent: D100=16#0031, D101=16#0032, D102=16#0033, D103=16#0034.
3. Set D10=16#0000 (sending data only, not receiving data).
4. Enable the contact X0.0.
5. The PLC sends 4 pieces of data.
6. Sending data: PLC→external equipment 31 32 33 34.
7. Since receiving data is not required, after the PLC sends out the data, the operation ends, and SM100=0.
6_
8. To send more data, set the flag SM100 to OFF to start the operation again.
6-641
Example 2
The mode in D2 is 1 (setting the timeout value to 5–3000 ms) and you set the mode for sending and receiving data to 16-
bit mode (SM106=OFF).
2. The contents for the data to be sent: D100=16#3231, D101=16#3433.
3. Set D10=16#0001 (mode: 1), D11=300 (set the timeout value to 300 ms).
5. PLC sends 4 pieces of data.
6. Sending data: PLC→external equipment 31 32 33 34.
7. After the external equipment receives the data from the PLC, it sends 5 consecutive data to the PLC, each sent in
less than 20 ms. External equipment→PLC 35 36 37 38 39.
_6 8. D200=5 (number of data received), and the content of data received: D201=16#3635, D202=16#3837,
D203=16#0039.
9. SM100=ON: reception of data is complete.
NOTE: When the sending of data is complete, the receiving flag SM98 is ON, and then the PLC starts to receive data.
You set the timeout between each data reception in D11. When the interval time exceeds the set timeout and no
data is received, SM100 is ON.
6-642
Example 3
The mode in D2 is 2 (the data received ends with a specific character.) and you set the mode of sending and receiving
data to 8-bit mode (SM106=ON).
1. Set the length of the data to be sent: D20=0, meaning the PLC will not send data but only receives data.
2. Set D10=16#0002 (mode: 2), D11=16#000A (the ending character is 16#0A).
4. The PLC waits to receive data from the external equipment. D20=0 means that the PLC does not send data to the
external equipment.
5. The external equipment sends data to the PLC.
External equipment → PLC 31 32 33 34 35 0A.
6. D200=6 (number the data received), the content of data received: D201=16#0031, D202=16#0032,
D203=16#0033, D201=16#0034, D202=16#0035, D203=16#000A

6_
NOTE: When the sending of data is complete, the receiving flag SM98 is ON and then the PLC starts receiving data until
receiving the ending character (16#0A). When the reception of data is complete, SM100 is ON. If the
communication timeout occurs but the ending character (16#0A) is still not received, the communication timeout
flag SM104 is ON.
6-643
Example 4
The mode in D2 is 3 (the data received ends with two specific characters.) and you set the mode for sending and
receiving data to 16-bit mode (SM106=OFF).
This example uses a DVP-ES2 as the external equipment and writes H1234 to D100 in the DVP-ES2.
2. The contents for the data to be sent: D100=16#303A, D101=16#3031, D102=16#3136, D103=16#3630,
D104=16#3134, D105=16#3332, D106=16#3334, D107=16#0D46, D108=16#000A.
3. Set D10=16#0003 (mode: 3), D11=16#0D0A (the ending characters are 16#0D and 16#0A).
Sending data: PLC→external equipment 3A 30 31 30 36 31 30 36 34 31 32 33 34 33 46 0D 0A
_6 (ASCII code: 0106106412343FCRLF)
6. The external equipment receives the data from the PLC and the last 2 data are 16#0D and 16#0A.
External equipment → PLC 3A 30 31 30 36 31 30 36 34 31 32 33 34 33 46 0D 0A
(ASCII code: 0106106412343FCRLF)
7. D200=17 (number of the data received), and the content of the received data: D201=16#303A, D202=16#3031,
D203=16#3136, D204=16#3630, D205=16#3134, D206=16#3332, D207=16#3334, D208=16#0D46,
D209=16#000A.
NOTE: When sending of data is complete, the receiving flag SM98 is ON and then the PLC starts receiving data until it
receives the ending character (16#0D0A). When the reception of data is complete, SM100 is ON. If the
communication timeout occurs but the ending character (16#0D0A) is still not received, the communication
timeout flag SM104 is ON.
6-644
Example 5
The mode in D2 is 4 (the data received starts with a specific character and you set the timeout value to 5–255 ms.) and
you set the mode of sending and receiving data to 8-bit mode (SM106=ON).
3. Set D10=16#0004 (mode: 4), D11=16#3A0F (the starting character is 16#3A and set the time value to 16#0F,
meaning 15ms).
Sending data: PLC→external equipment 31 32 33 34
6. The external equipment receives data from the PLC and then sends 7 consecutive words to the PLC with an
interval of 1 ms between each sending.
External equipment → PLC 30 3A 35 36 37 38 39

6_
D203=16#0036, D204=16#0037, D205=16#0038, D206=16#0039.
NOTE: When the sending of data is complete, the receiving flag SM98 is ON and then the PLC is ready to receive data.
When the PLC receives the starting character 16#3A, it starts receiving data. The interval timeout between
receiving each piece of data is set in D11. When the interval time exceeds the set timeout 16#0F (15 ms) and no
data is coming in, SM100 is ON.
6-645
Example 6
The mode in D2 is 5 (the data received starts and ends with a specific character) and you set the mode of sending and
receiving data to 16-bit mode (SM106=OFF).
The example uses a DVP-ES2 as the external equipment and reads data from D100 in the DVP-ES2.
2. The contents for the data to be sent: D100=16#303A, D101=16#3031, D102=16#3133, D103=16#3630,
D104=16#3034, D105=16#3030, D106=16#3831, D107=16#0D37, D108=16#000A
3. Set D10=16#0005 (mode: 5), D11=16#3A0A (the starting character is 16#3A and the ending character is 16#0A).
Sending data: PLC→external equipment 3A 30 31 30 36 31 30 36 34 31 32 33 34 33 46 0D 0A

_6
6. The external equipment receives data from the PLC and the last 2 data are 16#0D and 16#0A.
External equipment → PLC 3A 30 31 30 36 31 30 36 34 31 32 33 34 33 46 0D 0A
D203=16#3033, D204=16#3132, D205=16#3332, D206=16#4234, D207=16#0D34, D208=16#000A.
NOTE: When the data sending is complete, the receiving flag SM98 is ON and then the PLC is ready to receive data.
When the PLC receives the starting character 16#3A, it starts receiving data until receiving the ending character
16#0A, and SM100 is ON. If the communication timeout occurs but the starting character 16#3A or the ending
character 16#0A is still not received, the communication timeout flag SM104 is ON.
6-646
Example 7
The mode in D2 is 6 (the received data length) and you set the mode of sending and receiving data to 8-bit mode
(SM106=ON).
3. Set D10=16#0006 (mode: 6), D11=16#0008 (8 pieces of data to be received).
5. The PLC sends out 4 pieces of data.
6. The external equipment receives data from the PLC and then sends 8 consecutive data to the PLC.
External equipment → PLC 32 33 34 35 36 37 38 39

6_
7. D200=8 (number of the data received), and the content of the received data: D201=16#0032, D202=16#0033,
D203=16#0034, D204=16#0035, D205=16#0036, D206=16#0037, D207=16#0038, D208=16#0039.
When receiving a set quantity of data, the SM100 is ON. If the communication timeout occurs but the set quantity
of data is still not received, the communication timeout flag SM104 is ON.
6-647
Example 8
The mode in D2 is 7 (the data received ends with a specific character and generates communication interrupts) and you
set the mode of sending and receiving data to 8-bit mode (SM106=ON).
Communication interrupt programs:
1. Clear the interrupt: D30=0.
4. Set D10=16#0007 (mode: 7), D11=16#000A (16#0A is the ending character).

_6
7. D30=0 (the programs in the interrupt are not executed).
8. The external equipment sends data to the PLC.
External equipment → PLC 31 32 33 34 35 0A
D203=16#0033, D201=16#0034, D202=16#0035, D203=16#000A.
11. D30=1 (the interrupt is triggered and then INC D30 is executed).
When receiving the set ending character (16#06), SM100 is ON. If the communication timeout occurs but the set
ending character is still not received, the communication timeout flag SM104 is ON.
6-648
Example 9
The mode in D2 is 8 (the set quantity of data is received and generates communication interrupts) and you set the mode
of sending and receiving data to 8-bit mode (SM106=ON).
Communication interrupt programs:
1. Clear the interrupt: D30=0
4. Set D10=16#0008 (mode: 8), D11=16#0008 (8 pieces of data to be received).

6_
7. D30=0 (the programs in the interrupt are not executed).
8. The external equipment receives data from the PLC and then sends 8 consecutive data to the PLC.
9. External equipment → PLC 32 33 34 35 36 37 38 39
D203=16#0034, D204=16#0035, D205=16#0036, D206=16#0037, D207=16#0038, D208=16#0039.
12. D30=1 (the interrupt is triggered and then the INC D30 is executed).
When receiving the set quantity of data, SM100 is ON. If the communication timeout occurs but the set quantity of
data is still not received, the communication timeout flag SM104 is ON.
6-649
Example 10
The mode in D2 is 9 (the set ending character or the set quantity of data is received) and set the mode of sending
data/mode of receiving data to 8-bit mode (SM106=ON).
3. Set D10=16#0009 (mode: 9), D11=16#0A0F (the ending character is 16#0A and the set data length is 16#0F).
6. The external equipment receives data from the PLC and then sends 15 pieces of data to the PLC.
External equipment → PLC 31 32 33 34 35 0A 41 42 43 44 45 46 47 48 49
_6 7. D200=6 (number of the data received), and the content of the received data: D201=16#0031, D202=16#0032,
D203=16#0033, D204=16#0034, D205=16#0035, D206=16#000A.
The PLC stops receiving data after the 6th piece of data is received.
When receiving the set ending character or the set quantity of data, the SM100 is ON. If the communication
timeout occurs but the set ending character or the set quantity of data is still not received, the communication
timeout flag SM104 is ON.
6-650
Additional remarks
1. There is no limit on the number of times you can execute the COMRS communication instruction. However, each
communication port can only be enabled by one communication instruction, and the later communication
instructions that follow are not executed.
2. The instruction does not use checksum when you execute this instruction. If you need a checksum, use COMRS
and another available instruction.
3. If the value in D2 is 2, 3, 5, 6 or 9, it is suggested that you set a timeout period. After you set a timeout period, the
instruction tries to send the data again if a stop character is not received.
4. The instruction does not automatically clear the value in D1–D1+n whenever the instruction is executed or the PLC
begins to receive new communication data. You can know whether and how much data the PLC receives only after
a completion flag switches from OFF to ON . If the you want to clear the values in D1–D1+n, use the ZRST
5. If the value in S1 is out of range, the instruction is not executed.
6. If the number of devices starting from S2 is not equal to the value in S3, the instruction is executed, SM0 is ON, and
7. If the value in D2 is not between 0–9, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#200B.
8. If the value in D2 is 6, 8 or 9, and the number of devices starting from D1 is not equal to the value in D2+1, the
instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
9.
6_
If the quantity of data received is greater than the number of devices starting from D1, the data that cannot be stored
is ignored.
10. If a completion flag is ON, the PLC stops receiving data. If a communication port receives data when a completion
flag is ON, the data is not received.
11. If the setting value in S3 is not between 0–256, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
12. When the mode of D2 is 6 or 8, the length of D2+1 not between 1–256, the instruction is not executed. SM0 is ON,
and the error code in SR0 is 16#200B.
6-651
Setting the communication format for a serial

1813 COMDF P S1, S2, S3, S4, S5, D
communication port
S1  
S2  
S3  
S4  
S5  
D  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1
S2
S3
S4
S5
D

AS AS -
_6
Symbol
S1 ： Baud Rate (Unit:100 bps)
S2 ： Number of data bits
S3 ： Parity bit
S4 ： Number of end bits
S5 ： Modbus format selection
D ： Communication port number
Explanation
1. This instruction provides a way to directly set the parameter values, instead of declaring variables.
2. S1 sets the baud rate with the units 100 bps. For example, a value 96 indicates 9600 bps.
3. S2 sets the number of data bits. The value 7 indicates 7 data bits and 8 indicates 8 data bits. If the value is not 7 or
8 in S2, the instruction uses the default value.
6-652
4. S3 sets the parity bit. The value 0 indicates None (no parity bit). The value 1 indicates Odd bit checking. The value 2
corresponds to Even bit checking. If the value in S3 is not 0, 1 or 2, the instruction uses the default value.
5. S4 sets the number of end bits. The value 1 (preset) indicates 1 bit. The value 2 indicates 2 bits. If the value in S4 is
not 1 or 2, the instruction uses the default value.
6. S5 sets the communication mode for Modbus communication. The value 0 indicates ASCII (default value). The value
of 1 indicates RTU. If the value in S5 is not 0 or 1, the instruction uses the default value.
7. D sets communication port number. The number for COM1 is 1, COM2 is 2, Card1 is 11 and Card2 is 12. If the
setting value is out of the valid range, the instruction does not set the communication port format.
8. You can also directly set the communication port in HWCONFIG in ISPSoft (COM Port settings) or with the special
registers. For more on in HWCONFIG, see the ISPSoft user manual. Refer to Section 6.19.3 for setting the
communication-related SR and SM registers.
9. The communication at the actual communication port changes immediately after you change the setting of the
instruction. If some communication is being carried out at the moment, it is forced to cancel. Additionally, the
corresponding setting value in SM/SR changes accordingly. For details on SM/SR, refer to Section 6.19.3.
10. This instruction does not change any setting for the actual communication port when the communication format
setting is the same as the previous setting.
6_
Example
1. This example uses the PLC COM1 port. Other PLC communication ports are similar in the way you set up the
communication.
2. The contact for the start condition is X0.0.
3. Set the (RS485) communication format of PLC COM1 to 115200, 8, E and 1.
4. Set the (RS485) communication mode of PLC COM1 to ASCII.
5. The following table explains the COMDF operands for the example.
Operand Description Content value
S1 Baud Rate 115200 bps 1152
S2 Number of data bits 8 8
S3 Parity bit E 2
S4 Number of end bits 1 1
6-653
S5 Mobdus format selection ASCII 0
D Communication port number PLC COM1 1
_6
6-654
Serial communication instruction exclusive for

1814 VFDRW S1, S2, S3, S
Delta AC motor drive
S1      
S2      
S3      
S 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
S  

- AS -
Symbol
S1 ： Communication port number
S2 ： VFD station address

6_
S ： Source and received data
Explanation
1. S1 sets the communication port number. The number for COM1 is 1, COM2 is 2, Card1 is 11 and Card2 is 12. If the
value exceeds the valid range, the instruction does not receive any communication data.
2. S2 sets the station address for the VFD AC motor drive. 0 indicates that the instruction uses the broadcast mode.
The range is between 0–254, and the instruction is not executed if this value is out of the valid range.
6-655
3. S3 is the communication function code, and S is the source or received data as explained in the following table.
S3
function S3 function name S source and received data Remark
code
0 Reset due to abnormality Unused Any value can be stored in S.
1 Clockwise running command Velocity value Refer to AC motor drive user
Counterclockwise running manual for the setting value and

2 Velocity value
command the unit.
3 Stop Unused Any value can be stored in S.
Jog clockwise running

4 Unused Refer to AC motor drive user
command
manual for setting the jog
Jog counterclockwise running
5 Unused velocity.
command
Refer to AC motor drive user
manual for the meaning of the
state values of the 5 bit

6 Reading the state Received state values
addresses H2100–H2104 for
VFD.
_6
4. The following chart shows the timing for sending and receiving data.
Enable/disable t he exec ution

of the instruction
Sending data
Rec eption fl ag
Receiv ing data
Compl etion fl ag
  
 
6-656
Description:
  Start or stop the execution of the instruction.
  Transmitting data begins. During this time, the communication timeout time is not measured.
  The reception flag is set. From the moment when the first character is received to the moment when the next
character is received, the period of time is measured. Whenever a character is received, the measured time is
cleared to 0. The instruction generates the communication timeout flag if the time measured is greater than the
communication timeout setting value.
  When receiving of data is complete, the instruction sets the completion flag. You must clear the flag before
receiving more data.
  The instruction is stopped for one cycle after the completion flag is set. Then the instruction can be started in
the next cycle.
5. There is no limit to the number of times the instruction can be executed. The instruction can use only one
communication port for the output and execution of one communication instruction each time. If receiving and
sending data is complete, you must disable the instruction to correctly release the communication control.
only once.
Example of setting the communication protocol 6_

1. Set the PLC COM1 (RS485) port with station address 2 and the communication format in HWCONFIG with these
values: ASCII, 115200, 7, N, 2.
2. Set the motor drive parameters using the panel on the Delta C2000 AC motor drive according to the following steps.
A. Set 09-00 to 1: the station address of the AC motor drive is set to 1.
B. Set 09-01 to 115.2: RS485 baud rate of the AC motor drive is 115200.
C. Set 09-04 to 1: RS485 communication format of the AC motor drive is 7, N, 2.
D. Set 09-20 to 1: the frequency instruction is input through RS485.
E. Set 09-21 to 2: the running instruction is input through RS485.
6-657
Example
Use the VFDRW instruction to control the velocity: make the VFD run forward at the frequency of 120Hz, then run in
reverse at the frequency of 180Hz, and then stop running.
_6
1. Connect AS COU to VFD.
Set D202=12000 initially. When M1 is ON, VFD starts to accelerate after receiving the clockwise running command,
and runs clockwise at 120Hz.
2. Set D204=18000 initially. When M2 is ON, VFD starts to decelerate until it stops after receiving the counterclockwise
running command, and runs counterclockwise at 180Hz.
6-658
3. When M3 is ON (at this time, the value in D206 is ignored), VFD decelerates to stop after receiving the stop command.
4. When M4 is ON, the instruction reads the values of H2100–H2104 of VFD and stores them in D220–224.
Device D220 D221 D222 D223 D224
Frequency
Content Error code VFD state Output frequency Output current
command
The state of the VFD:
Bit2=1 causes the VFD to execute the Jog command. Bit4–3=11B causes the VFD to run counterclockwise. The
frequency command is 18000, and causes the VFD to run at 180Hz. For the definitions of the parameter addresses
in the communication protocol, refer to the Delta AC Motor Drive user manual.
5. The reception completion flag SM100 is ON, and the values of M1–M5 are cleared to avoid interfering with the next
communication command.
After receiving the data that the VFD sends back, the instruction checks the format of the data sent back from VFD.
If the data format is correct, SM100 is ON; otherwise, SM102 is ON.
6_
6-659
Serial communication instruction exclusive for

1815 ASDRW S1, S2, S3, S
Delta servo drive
S1      
S2      
S3      
S 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data INT
type
S1  
S2  
S3  
S  

- AS -
Symbol
S2 ： Station address of the servo

_6
S ： Source and received data
Explanation
1. S1 sets the communication port number. The number for COM1 is 1, COM2 is 2, Card1 is 11 and Card2 is 12. If the
value exceeds the valid range, the instruction does not receive any communication data.
2. S2 sets the station address for the servo. 0 indicates that the instruction uses the broadcast mode. The range of the
value is between 0–254. The instruction is not executed if the value is out of the valid range.
3. Refer to Delta Servo Operation manual for details on servo parameters.
4. S3 is the communication function code, and S is the source or received data as explained in the following table.
6-660
S3 and S operands for the A, AB, A+, B Series
S3 function
S3 function name S source or received data Remark
code
Occupies 5 consecutive devices Reading the state value from

0 Reading the servo state value
S–S+4 P0-04–P0-08
Reading the servo register Occupies 8 consecutive devices Reading the value from the
1
value S–S+7 registers P0-09–P0-16
Occupies 8 consecutive devices Writing the data in the registers

2 Writing the servo register value
S–S+7 P0-09–P0-16
The range of velocity: 1–3000;

Jog velocity input, clockwise
4999 (run clockwise) Writing the data into the
3 running, counterclockwise
4998 (run counterclockwise) registers P4-05
running and stop
5000 (stop)
1: Servo On Writing the data into the

4 Servo ON/OFF
Any other value: Servo OFF registers P2-30
Writing the data into the

5 Velocity command Valid range: -5000 to 5000
registers P1-09–P1-11
Writing the data into the

6 Torque command Valid range: -300 to 300
registers P1-12–P1-14
6_
S3 and S operands for the A2, B2 Series
S3 function
S3 function name S source or received data Remark
code
Reading the servo state value Occupies 10 consecutive Reading the state value from
16 devices S–S+9 the registers P0-09–P0-13
(32-bit value)
Writing data into the servo Occupies 8 consecutive devices Writing the data into the
17 register S–S+7 registers P0-17–P0-20
(32-bit value)
Writing the mapping parameter Occupies 8 consecutive devices Writing the data into the
18 value *1 S–S+7 registers P0-25–P0-28
(32-bit value)
Jog velocity input, run Valid range of velocity: Valid Writing data into the registers
19
clockwise, run range 1–5000; P4-05
6-661
counterclockwise, 4999 (run clockwise)
stop 4998 (run counterclockwise)
0 (stop)
Servo ON/OFF 1: Servo On Writing the data into the

20
Any other value: Servo OFF registers P2-30
Velocity command Occupies 6 consecutive devices Writing data into the registers
21 (3 sets) with the valid setting value P1-09–P1-11
range: -60000 to 60000 (32-bit value)
Torque command Occupies 6 consecutive devices Writing the data into the
22 (3 sets) with the valid setting value registers P1-12–P1-14
range: -300 to 300 (32-bit value)
Setting the mapping targets of Occupies 8 consecutive devices Writing the data into the
23 servo parameters S–S+7 registers P0-35–P0-38
(32-bit value)
*1: B2 series does not support function code 18 and 23.
5. The following chart shows the timing for sending and receiving data.
Enable/disable t he exec ution
_6
of the instruction
Sending data
Rec eption fl ag
Receiv ing data
Compl etion fl ag
  
 
Description:
 Start or stop the execution of the instruction.
Transmitting data begins. During this period, the communication timeout time is not measured.
 The reception flag is set. From the moment when the first character is received to the moment when the next
character is received, the period of time is measured. Whenever a character is received, the measured is
cleared to 0. The instruction generates the communication timeout flag if the time measured is greater than the
6-662
communication timeout setting value.
  When receiving of data is complete, the instruction sets the completion flag. You must clear the flag before
receiving more data.
  The instruction is disabled for one cycle after the completion flag is set. Then the instruction can be started in
the next cycle.
6. There is no limit to the number of times the instruction can be executed. The instruction can use only one
communication port for the output and execution of one communication instruction each time. If receiving and
sending data is complete, you must disable the instruction to correctly release the communication control.
only once.
Example of setting the communication protocol:
1. Set the PLC COM1 (RS485) port in HWCONFIG with these values: ASCII, 115200, 8, E, 1
2. Set the servo parameters using the panel on the Delta ASDA-A2 servo according to the following steps.
A. Set P2-08 to 10 to restore the factory settings.
B. Cycle the power on the servo off and then back on.
C. Set P1-01 to 0001 (PR mode). 6_

D. Set P3-00 to 2: the station address of the servo is set to 2.
E. Set P3-01 to 0205: the RS485 baud rate of the servo is set to 115200.
F. Set P3-02 to 0004: the RS485 communication format of the servo is set to 8, E, 1.
G. Cycle the power to the servo again after completing these settings.
6-663
Example
Use the ASDRW instruction to control the velocity: make the servo run to the relative position 5000000 PUU by accelerating
for 400 ms to the speed 3000.0 r/min and then decelerating for 200 ms.
_6
6-664
1. Connect the AS CPU to ASDA-A2.
Set D100=1 initially. When M1 is ON, ASDA-A2 is Servo ON.
2. Set the values in D200–D207 as in the following table, which are written to P0-35–P0-38 in the ASDA-A2. The values
occupies 8 consecutive devices.
Device D200 D201 D202 D203 D204 D205 D206 D207
Setting value (16#) 05140515 06020602 06030603 053C0507
When M2 is ON, the values in D200–D207 are written to P0-35–P0-38 in the ASDA-A2.
The setting values of P0-35–P0-38 are set the mapping target for P0-25–P0-28. You can set the mapping target;
refer to the Delta servo operation manual.
ASDA-A2 P0-35 P0-36 P0-37 P0-38
Setting value (16#) 0514 0515 0602 0602 0603 0603 053C 0507
Setting the value of P0-38 to 053C 0507indicates that the mapping parameter target for P0-28 is P5-60 (16 bits) and
P5-07 (16 bits). 6_
ASDA-A2 P0-25 P0-26 P0-27 P0-28
Mapping parameter
P5-20, P5-21 P6-02 P6-03 P5-60, P5-07
target
Acceleration/deceleration
Target velocity and
time1
Parameter name Path type1 Path1 data PR command trigger
Acceleration/deceleration
time2
3. The following table shows the setting values in D220–D227.
Device D220 D221 D222 D223 D224 D225 D226 D227
Setting value (16#) 0190 00C8 0000 1083 4C4B40 7530 0001
When M3 is ON, the values in D220-D227 are written into P0-25–28 in the ASDA-A2.
ASDA-A2 P0-25 P0-26 P0-27 P0-28
Setting value (16#) 0190 00C8 0000 1083 4C4B40 7530 0001
6-665
The servo starts running with the parameters: acceleration time=0190 (400 ms), deceleration time=00C8 (200 ms),
path type=1083, position command=4C4B40 (5000000 PUU), target velocity=7530 (3000.0 rpm) and PR command
trigger =1.
4. Set the values in D240-D247 as shown in the following table, to be written into P0-17–P0-20 in the ASDA-A2. The
values occupy 8 consecutive devices.
Device D240 D241 D242 D243 D244 D245 D246 D247
Setting value (10#) 41 0 0 0
When M4 is ON, the values in D240–D247 are written into P0-17–20 in the ASDA-A2.
The setting values of P0-17–20 set the contents of P0-09–12.
You can set the contents to be displayed; refer to the Delta Servo Operation manual.
ASDA-A2 P0-17 P0-18 P0-19 P0-20
Setting value (10#) 41 0 0 0
Setting P0-17 to 41 indicates that the contents of P0-09 is the drive state.
ASDA-A2 P0-09 P0-10 P0-11 P0-12
Number of motor Number of motor Number of motor

Content Drive state
feedback pulses feedback pulses feedback pulses
_6
5. When M5 is set to ON, the values of P0-17- P0-20 of ASDA-A2 are read to D260-D267.
Device D260 D262 D264 D266
Number of motor Number of motor Number of motor

Content Drive state
feedback pulses feedback pulses feedback pulses
When the drive state bit (Bit 4) is one, it indicates that the target position is reached.
Refer to Delta servo operation manual for the explanation for P0-46.
6. When the reception completion flag SM100 is set to ON, the instruction clears the values of M1–M5 to avoid
interfering with the next communication command.
After receiving the data that the ASDA-A2 sends back, the PLC checks the format of the data sent back from the
ASDA-A2. If the data format is correct, SM100 is ON; otherwise, SM102 is ON if the data format is incorrect.
6-666

Setting the parameters in the data
1816 CCONF P S1-S11
exchange table for a communication port

S1    
S2    
S3    
S4    
S5    
S6    
S7  
S8    
S9    
S10    
S11  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1-S11 Refer to the explanation for the instruction.

AS AS -
Symbol
S1-S11 ： Refer to the explanation for the instruction.
6_
6-667
Explanation
1. The following table lists the names and descriptions of S1–S11.
Device Name Description Data type Remark
1=COM1, 2=COM2. 11=Function card 1,
12=Function card 2. PLC with FW V1.06.00

Communication port
S1 or later supports function card 1 and 2. WORD
number
Any other value, the instruction does not
modify the operand.
Valid range: 1–32.

Item number in the data
S2 If the value is out the range, the instruction WORD
exchange table
does not modify the operand.
Valid range: 0 and 1–240. A
If the value is greater than 240, the negative

The station address of the
S3 instruction uses 240 as the value. If the WORD number is
remote equipment
value is less than or equal to 0, the original processed
station address is not changed. as 0.
Supports 16#01, 02, 03, 04 and 17.
Function code for reading If the value exceeds the valid range, the
S4 WORD
_6 data instruction does not modify the operand. If
S4=16#17, it is processed as 16#17.
Reading the remote

S5 16#0000–16#FFFF WORD
communication address
Bit function code, 16#01, 02: Supports 1–
256 bits;
Word function code, 16#03, 04, 17:
Supports 1–100 words.

S6 Reading data length WORD
If the value is 0 or smaller than 0, it indicates
do not read data.
If the value is greater than the maximum, the
instruction uses the maximum value.
Bit function code: only M device can be
The local register for selected. BOOL

S7
storing the data received Word function code: only D device can be WORD
selected.
6-668
Device Name Description Data type Remark
Supports 16#05, 06, 0F, 10.

Function code for writing
S8 If the value is out of the range, the instruction WORD
data
does not modify the operand.
Writing the remote

S9 16#0000–16#FFFF WORD
Bit function code, 16#0F: Supports 1–256
bits;
Word function code, 16#10: Supports 1–100
words. For function code 16#06, the value
S10 Writing data length can only be 1. WORD
If the value is 0 or smaller than 0, it indicates
do not read data.
If the value is greater than the maximum, the
instruction uses the maximum value.
The local register into

Bit function code: only M can be selected. BOOL
S11 which the remote data are
Word function code: only D can be selected. WORD
written
6_
2. It is suggested that you use the pulse instruction.
3. See the details about the Modbus function codes in S4 and S8 below.
The command for the AS reads the data from several bit devices (which are not discrete input devices) is 1 (16#01).
The command for the AS reads the data from several bit devices (which are only discrete input devices) is 2 (16#02).
The command for the AS to read the data from several word devices (which are not input registers) is 3 (16#03).
The command for the AS to read the data from several word devices (which are only input registers) is 4 (16#04).
The command for the AS to write the state into a bit device is 5 (16#05).
The command for the AS to write the state into a word device is 6 (16#06).
The command for the AS to write the state into several bit devices is 15 (16#0F).
The command for the AS to write the data into several word devices is 16 (16#10).
The command for the AS to synchronously read from and to write the data into several word devices is 23 (16#17).
Only the function codes listed above are supported. Other function code setting values, such as 0, are invalid
6-669
(including communication address, length and the start register), and the instruction executes the data exchange
function based on the original communication parameter settings.
4. When you select 16#17 (for reading and writing synchronously) in S4 (the function code for reading), the operand
S8 (the function code for writing) is processed as invalid and 16#17 is automatically processed for writing data.
5. For PLC with FW V1.04.00 or previous versions: if you select16#05 or 16#06 in S8 (the function code for writing),
the operand S10 (the data length) is invalid and 16#05 or 16#06 indicates writing a piece of data.
6. The parameter values specified by the instruction are valid only while PLC is running. If you cycle the power on the
PLC, the data in the data exchange table set in HWCONFIG are taken as default values. If you want to modify the
values for parameters, use this instruction.
7. You can use the instruction to immediately set the parameters for the communication connection when the data
exchange function is not running. The new communication parameters are not used until the next cycle if the data
exchange function is running; however, the instruction changes the communication parameters for the connection
number.
For example, while the data exchange function is running with the parameters set for connection 3, you can specify
new the parameters for connection 3. The new parameters are not used until the next cycle when connection 3
starts.
8. The instruction only allows you to change the communication parameters. Refer to the following table for the flags
_6
to start and close the communication connection function if you use the PLC program to perform those functions.
When you set the automatic scan function through ISPSoft, the start/stop flag of the connection number
automatically updates the start/stop state once after the data exchange function finishes executing the scan.
The following table describes the SM flags.
SM No. Attribute Explanation for COM1 data exchange parameters
SM750 R/W Enables data exchange
SM752–SM783 R/W Enables data exchange connections 1–32
SM784–SM815 R Reading success for data exchange connections 1–32
SM816–SM847 R Error flags for data exchange connections 1–32
SM No. Attribute Explanation for COM2 data exchange parameters
SM864–SM895 R/W Enables data exchange connections 1–32
SM896–SM927 R Reading success for data exchange connections 1–32
SM928–SM959 R Error flags for data exchange connections 1–32
6-670
SM No. Attribute Explanation for Function Card 1 data exchange parameters
SM1712 ~ SM1743 R/W Enables data exchange connections 1–32
SM1744 ~ SM1775 R Reading success for data exchange connections 1–32
SM1776 ~ SM1807 R Error flags for data exchange connections 1–32
SM No. Attribute Explanation for Function Card 2 data exchange parameters
SM1824 ~ SM1855 R/W Enables data exchange connections 1–32
SM1856 ~ SM1887 R Reading success for data exchange connections 1–32
SM1888 ~ SM1919 R Error flags for data exchange connections 1–32
The PLC sets the flag to ON when the reading success flag indicates that receiving data is complete and the data
checked are correct. If an error occurs in receiving data or a communication timeout occurs, the error flag is set to
ON refer to the error codes). The PLC does not reset any of the reading success or error flags to OFF in the data
exchange since the reading success flag and error flag of every connection number are not ON simultaneously.
9. The following table describes the SR (only-read registers) in the data exchange function.
SR No. Description
SR1335 Cycle of the actual connections 1–32 in the COM1 data exchange 6_
SR1336 Cyclic connection number in the current COM1 data exchange
SR1340–SR1371 Error codes of the connections 1–32 in the COM1 data exchange
SR1375 Cycle of the actual connections 1–32 in the COM2 data exchange
SR1376 Cyclic connection number in the current COM2 data exchange
SR1380–SR1411 Error codes for connections 1–32 in the COM2 data exchange
SR1435 Cycle of the actual connections 1–32 in the Function Card 1 data exchange
SR1436 Cyclic connection number in the current Function Card 1 data exchange
SR1440 ~ SR1471 Error codes of the connections 1–32 in the Function Card 1 data exchange
SR1475 Cycle of the actual connections 1–32 in the Function Card 2 data exchange
SR1476 Cyclic connection number in the current Function Card 2 data exchange
SR1480 ~ SR1511 Error codes of the connections 1–32 in the Function Card 2 data exchange
10. The data exchange function does not provide a writing success flag. It is suggested that you refer to the connection
number in the execution to judge whether the writing of data succeeds or not.
6-671
For example, when the executed connection number is 3 in SR1336, the successive communication actions are to
read the communication data first, and then to write the communication data after reading is completed. The
connection number is incremented to 4 after writing is completed.
11. If the reading data length value in S6 and the initial device in S7 are out of the range of the D or M device, the length
value in S6 is automatically set to be in the valid range. For example, if the length value in S6 is100 and the initial
device of S7 is M8182, the value in S6 is set to 10 automatically.
12. In the following cases, the instruction is not executed and the parameter settings in HWCONFIG are not changed
for the communication port, and SM0 is set to ON, and the error code in SR0 is 16#200B.
 An input error occurs when the setting values in S1, S2, S4 and S8 are out of the specified range.
 When S4 or S8 function code selects the bit type for reading or writing data, the local device for storing data
S7 or S11 must select the M device. An input error occurs if the selection is not M.
 When the S4 or S8 function code selects the word type for reading or writing data, the local device for storing
data S7 or S11 must select the D device. An input error occurs if the selection is not D.
Example: AS COM1 (RS485)
1. For the data exchange between the AS Series CPU and the DVP-ES2 CPU, the following table shows the COM1
data exchange table in HWConfig in ISPSoft.
_6 Detection
Remote
Local Remote Function
Item No. station Length How to start
method device device code
address
Specified D50  D50 50 H03 Program

1 2
connection D100  D100 50 H10 control

2 2
2. Before starting data exchange, suppose that the corresponding data between the AS Series CPU and the DVP-ES2
CPU are listed in the following table.
AS PLC (Master) Content value ES2 PLC (Slave) Content value
D50-D99 0 D50-D99 1-50
D100-D149 100-149 D100-D149 0
D150-D199 0 D150-D199 150-199
D200-D249 200-249 D200-D249 0
6-672
3. The data exchange between the AS Series CPU and the DVP-ES2 CPU starts when X0.1 is ON.
6_
4. After data exchange starts, the corresponding data between the AS Series CPU and the DVP-ES2 CPU change as
shown in the following table.
D50-D99 1-50 D50-D99 1-50
D100-D149 100-149 D100-D149 100-149
D150-D199 150-199 D150-D199 150-199
D200-D249 200-249 D200-D249 200-249
6-673
5. When X0.0 is ON, the COM1 data exchange table parameters in the AS Series CPU are modified as shown in the
following table.
Item Remote station Remote Function How to

Detection method Local device Length
No. address device code start

1 3
M100  M0 10 H01
Specified Program
2 3
connection M110  M50 10 H0F control
6. Due to the change of COM1 data exchange table parameters, the corresponding data between the AS Series CPU
and the DVP-ES2 CPU are modified as shown in the following table.
D5000 3000 D500 3000
D6000 4000 D600 4000
M100-M109 ON M0-M9 ON
M110-M119 OFF M50-M59 OFF
_6
6-674

Reading and writing Modbus data without using any
1817 MODRWE S1, S2, S3, S4, S, n, D
flags

S1    
S2    
S3    
S4    
S 
n    
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1  
S2  
S3  
S4  
S   
n  
D 

- AS -
Symbol 6_
S2 ： Unit address
S ： Register for reading and writing the data
n ： Data length
D ： Flag for completion of the reading and writing data
Explanation
1. S1 sets the serial number of a communication port. The number of COM1 is 1, COM2 is 2, Card1 is 11 and Card2 is
12. If the value exceeds the valid range, the instruction does not receive any communication data.
2. Refer to the explanation of the MODRW instruction (API 1808) for the meaning of the operands S2, S3, S4, S and n.
3. D sets the communication state flags when the instruction completes the communication, and the flags occupy 3
consecutive devices. You must reset the flags to OFF. The following table gives explanations of the flag states.
6-675
Operand Description
D Receiving data successful.
D +1 Error occurs in receiving data.
D +2 Reception timeout flag
NOTE: Only one flag is set to ON among the three state flags, and the corresponding special flags (SM) are also set
to ON every time the communication is completed. Refer to Section 6.19.3 for the use of the special flags.
4. The timing for sending the instruction begins when the instruction starts. You must disable the instruction for a scan
cycle after communication is completed. The next communication instruction can be sent as soon as the instruction
is restarted.
5. The communication action and control sequence of the instruction are similar to MODRW instruction (API 1808). The
only difference between the two instructions is that you can send the communication command without control over
the flag for sending data.
only once.
Example
_6 You can compare the MODRW program and MODRWE program, for example, by using the PLC COM1 and function code
03 to read eight pieces of data from D20 in the DVP-ES2. The same is true for other PLC communication ports. Refer to
the MODRW instruction (API 1808) and the following example for the use of other function codes.
1. The device address of D20 in the DVP-ES2 CPU (16#1020) and the content values in D20–D27 are shown in the
following table.
Device D20 D21 D22 D23 D24 D25 D26 D27
Value (16#) 1234 5678 1122 3344 5566 7788 99AA BBCC
2. The AS Series PLC reads the content values from D20–D27 in the DVP-ES2 CPU through communication.
6-676
Method 1: Using MODRW instruction
The data in D20-D27 of the DVP-ES2 are read when SM96 is ON and X0.0 is ON.
The following table explains the MODRW operands.

6_
S3 Reading the device address of D20 16#1020
S First register for storing the data read D10
n Reading the data length 8
The communication response between the AS Series CPU and the DVP-ES2 depends on the mode.
ASCII mode: You do not need to convert the ASCII codes, and they are expressed in 16# values.
 AS sends the communication command: “01 03 10 20 00 08 C4 CR LF”
 AS receives the communication command: “01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC AA

CR LF”
6-677
RTU mode
 AS sends the communication command: “ 01 03 10 20 00 08 41 06”
 AS receives the communication command: “01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC 90

FE”
SM100 is ON if there is no error in the data.
After the receiving of the data sent from the DVP-ES2, the PLC confirms the data format sent back from the DVP-
ES2. If there are no errors in the format, SM100 is ON; otherwise, SM102 is ON. SM104 is ON if there is no
response.
Method 2: Using MODRWE instruction
The data in D20-D27 of the DVP-ES2 are read when X0.0 is ON.
_6
The following table explains the MODRWE operands.
S1 Communication port number 16#0001
S4 Reading the device address of D20 16#1020
S First register for storing the data read D10
n Reading the data length 8
D Flag for completion of reading and writing data M0
The communication response between the AS series CPU and the DVP-ES2 depends on the mode.
6-678
ASCII mode: You do not need to convert the ASCII codes, and they are expressed in 16# values.
 AS sends the communication command: “01 03 10 20 00 08 C4 CR LF”
 AS receives the communication command: “01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC AA

CR LF”
RTU mode
 AS sends the communication command: “01 03 10 20 00 08 41 06”
 AS receives the communication command: “01 03 10 12 34 56 78 11 22 33 44 55 66 77 88 99 AA BB CC 90

FE”
M0 is ON when there is no error in the data.
After the receiving of the data sent from the DVP-ES2, the PLC confirms the data format sent from DVP-ES2. If
there is no error in the format, M0 is ON; otherwise, M1 is ON. M2 is ON if there is no response. The
corresponding special flags SM100, SM102 and SM104 are ON as well.
3. The following table lists the content values in D10–D17 of AS CPU.
Device D10 D11 D12 D13 D14 D15 D16 D17
Value (16#) 1234 5678 1122 3344 5566 7788 99AA BBCC
6_
Additional remarks
1. If you declare the operand in IPSSoft, the data type is ARRAY [3] of BOOL.
2. If D+2 exceeds the device range, the instruction is not executed, SM0 is ON and the error code in SR0is 16#2003.
6-679
S1，S2，S3，S4，S5，S6，S7，S8，S9， Reading and writing DeviceNet

1818 DNETRW
S10，D1，D2，D3，D4，D5 communication data

S1    
S2    
S3    
S4    
S5    
S6    
S7    
S8 
S9    
S10    
D1   
D2   
D3 
D4 
D5 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
_6 S2  
S3  
S4  
S5  
S6  
S7  
S8  
S9  
S10  
D1 
D2 
D3  
D4  
D5  

－ AS －
6-680
Symbol
Number of the module sending the DeviceNet
S1 :
communication
S2 : DeviceNet MAC ID
S3 : Service Code
S4 : Class ID
S5 : Instance ID
S6 : Attribute ID
S7 : Written-data length
S8 : Device for storing written data
S9 : Communication timeout time
S10 : Number of times of retransmission
D1 : Completion flag
D2 : Error flag
D3 : Error code
D4 : Read-data length
D5 : Device for storing read data
Explanation 6_
1. S1 is the serial number of the module at the right of the PLC. The first one is number 1, the second one is number 2
and so on. Whatever modules at the right of the PLC must be numbered. The setting range is 1~32. If the setting
value (<1 or >32) exceeds the range, the instruction will run at the minimum value or maximum value.
2. S2 is the DeviceNet Mac ID within the range: 0~63. It can be the Mac ID of the slave which the master is to read and
write as well as the Mac ID of the master which means to read and write the data in the master.
3. S3 is the DeviceNet service code.
Service code Description
0x01 Read all attributes (Get_Attribute_All)
0x02 Set all attributes (Set_Attribute_All)
0x0E Read one single attribute
(Get_Attribute_Single)
0x10 Set one single attribute (Set_Attribute_Single)
4. S4, S5 and S6 are respectively class ID, instance ID and attribute ID for specifying the parameter path in the EPATH
of the DeviceNet protocol.
6-681
5. S7 is the length of written data with the unit of byte.
6. S8 is the starting address of the devices where written data are stored in the order from low bit to high bit.
7. S9 is the communication timeout time. The range of the setting value is 1~100 and the unit is 0.1s (second).
8. S10 is the number of retransmission times and the range is 0~3. When the communication timeout occurs, the
communication will be transmitted again.
9. D3 displays the read or write error code.
Error code
Description
Code 1 (High Byte) Code 2 (Low Byte)
XX FF Not conform with DeviceNet standard
20 01 The target slave does not exist.
20 02 Making the connection with the slave failed.
20 03 Sending the explicit message failed.
16 00 Communication timeout
10. D4 is the read data length with the unit of byte.
11. D5 is the starting address of the devices where read data are stored in the order from low bit to high bit.
_6 12. D1 is the communication completion flag and D2 is the error flag. See the detailed communication sending procedure
and sequence diagram.
 The DNETRW instruction is enabled for the first time and the command will be sent out immediately if the
instruction is not be occupied by other DeviceNet communication.
 The command is being sent.
 The data sending is completed and the completion flag or error flag changes to On according to the response.
 The next message is ready to be sent out. The next command is sent out right after the completion flag or error
flag is cleared.
 The command sending is completed and the DNETRW instruction is disabled.
6-682
only once.
6_
6-683

User-defined CAN communication sending and
1819 CANRS S1，S2，S3，S4，D1，D2，D3
receiving

S1    
S2  
S3    
S4  
D1 
D2    
D3    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4  
D1  
D2 
D3 

- AS -
_6 Symbol
S1 : Communication mode setting
S2 : Communication ID (MsgID)
S3 : Sent-data length
S4 : Starting device where sent source data are stored
D1 : Starting device where received data are stored
D2 : Communication completion flag
D3 : Communication error flag
Explanation
1. The CANRS instruction is applicable to AS series PLC with the firmware of V1.04.00 and later.
2. Before the CANRS instruction is executed, please ensure that HWCONFIG for the hardware configuration has
selected CANopen DS301 as the mode of function card 2.
6-684
3. S1 sets the communication mode. See the following modes that the instruction supports. If the setting value is
incorrect, the error flag D3 changes to On and the error code SR659 is set to 1.
Communication
Setting
code Communication
value of Description
High 8 Low 8 format
S1
bits bits
Master mode. The master will wait to receive the
0 16#0000 response message after sending out the communication
data.
Master mode. After sending the broadcast command,
2.0A the master will enter the mode of receiving messages

0 1 16#0001
11-bit ID from multiple slaves until the receiving timeout occurs or
the quantity of messages received is up to 100.
Slave mode. The slave receives a message first and

2 16#0002
then sends back the response message.
3 16#0003 Slave mode. The slave only receives messages.
Master mode. The master will wait to receive the

0 16#0100
response message after sending out a message.
Master mode. After sending the broadcast command, 6_

the master will enter the mode of receiving messages
1 16#0101 2.0B
1 from multiple slaves until the receiving timeout occurs or
29-bit ID
the quantity of messages received is up to 100.
Slave mode. The slave receives a message first and

2 16#0102
then sends back the response message.
3 16#0103 Slave mode. The slave only receives messages.
4. S2 is the ID of the transmitted message. According to 2.0A or 2.0B protocol, the transmitted data automatically
occupies D buffer registers.
When 2.0A is selected, S2 is 11 bits of ID code with the following data transmission format.
S2 No. S2
Description Msg. ID
When 2.0B is selected, S2 (Lo-word) and S2+1 (Hi-word) are both 29 bits of ID code.
S2 No. S2 S2+1
Description Msg. ID（Lo-word） Msg. ID（Hi-word）
6-685
5. S3 is the length of the transmitted message. The setting value should be in the range of 0~8 with the unit of byte
(8bits). If the setting value (<0 or >8) exceeds the range, the instruction will run at the minimum value 0 or the
maximum 8. If the length of the transmitted message is 0, the communication mode will automatically change into
the slave mode to receive messages without sending out any data. The mode can be used to monitor the
communication packet.
6. S4 is the starting device where transmitted data are stored and only the following 8 bits of data are used.
For example, 4 messages are transmitted with D10 as the starting device. See the data transmission sequence as
below.
S4 No. D10 D11 D12 D13
Description Data1 Data2 Data3 Data4
7. If S1 is the master mode in which the master will wait to receive data after sending data or the slave mode, the
received data will be directly stored in the device specified by D1. D100 is specified by D1 Here See the stored
content format.
2.0A mode setting:
D1 No. D100 D101 D102 ~ D109 (Lower 8 bits)
Description Msg. ID Data Length Data1 ~ Data8
2.0B mode setting

_6
D1 No. D100 D101 D102 D103 ~ D110 (Lower 8 bits)
Description Msg. ID（Lo-word） Msg. ID（Hi-word） Data Length Data1 ~ Data8
Note: If the Msg. ID to be received need be specified at the stage of receiving data, set the value of D1/ D1+1
beforehand based on the 2.0A/2.0B mode. If the Msg. ID is not specified, please clear the value of D1/ D1+1 to 0
before receiving data.
8. If S1 is the master broadcast mode, the received data will be stored in the device specified by D1. D100 is specified
by D1 here. See the storage format as below.
Selecting 2.0A mode: (Here is the introduction of receiving data from 2 slaves. For other data, please increase the
Device number specified by D1)
Response Data from the second Data from the

Data from the first slave
sequence slave third slave
D103 ~ D110
D1 No. D100 D101 D102 D111 D112~D120 D121~130
(Lower 8 bits)
Receiving
Data ID, Length,
Description Packet Msg. ID Data1 ~ Data8 Msg. ID Length, Data
Length Data
number
6-686
Selecting 2.0B mode: (Here is the introduction of receiving data from 2 slaves. For other data, increase the number
of D1)
Response Data from the second

Data from the first slave
sequence slave
D104 ~ D111
D1 No. D100 D101 D102 D103 D112~D122
(Lower 8 bits)
Receiving
Msg. ID（Lo- Msg. ID（Hi- Data
Description Packet Data1 ~ Data8 ID, Length, Data
word） word） Length
number
9. D2 and D3 are the receiving-completed flag and error flag respectively. The two flags will judge if the data receiving
is completed or an error occurs based on the current communication state when the instruction is scanned. If the
data receiving is completed or an error occurs, the flags will change to On. The two flags will be cleared and
change to Off automatically every time the instruction is enabled.
10. When the instruction is set to the master mode, using the receiving timeout setting in HWCONFIG is
recommended. So D3 will change to On and the error code 2 will be recorded in SR659 if the communication
packet has not been received fully within the specified period of time.
If the receiving timeout time is set to 0, it indicates that the communication timeout is not limited and the status can
be applied to the slave mode.
Note: The communication control right can not be released until the instruction is disabled by manual when the 6_
method in which there is no limit to the communication timeout is adopted.
11. There is no limit to the number of times of using the instruction. But only one CAN communication command is
allowed to be sent every time. If one command is being sent or received currently, the next CANRS instruction can
not be enabled.
12. Here is the CAN BUS format and every bit of content for Msg. ID is explained as below.
As 2.0A protocol is selected and the value of S2 is 16#0123, the Msg. ID content is shown in the following table.
Bit No. 15 ~ 11 10 ~ 8 7~4 3~0
S2 value (16bits) - 1 2 3
As 2.0B protocol is selected, the value of S2 is set to 16#1234 (Lo-word) and S2+1 is 16#0567 (Hi-word), the Msg.
ID content is shown in the following table.
Bit No. 31 ~ 29 28 27 ~ 24 23 ~ 20 19 ~ 16 15 ~ 0
S2 value (32bits) - 0 5 6 7 1234
13. If the operand D1 is declared in a variable, using the Word-type matrix is recommended.
6-687
14. See CANRS communication sequence diagram and explanation.
：The CANRS instruction is enabled. If no other CANRS instruction occupies the control right, the flags D2 and
D3 are cleared and then the data are sent out right away.
：The data sending is completed and meanwhile the data receiving starts. After the receiving is completed, the
completion flag D2 changes to On.
：The instruction sends data again after you clear the flag D2.
：As the receiving timeout occurs, D3 changes to On.
：If an error is found, you can disable the instruction. Alternatively, you can have the instruction resend data after
clearing the flag D3.
enable
CANRS disable disable



S4
 
D1
 

D2
D3
_6
Example 1
Master Mode
Using the CANRS instruction, the 6-byte data in D10~D15 are transmitted to the slave and the response data from the
slave are stored in the devices starting from D100. M100 changes to On when the sending and receiving are over.
See the explanation of relevant parameters.
Master mode_MsgID=2
0= master mode, waits to receive the response from the slave after sending out
Communication mode
data.
The MsgID of the sent message

Communication ID
D0=1
Sent-data length 6 BYTE
Starting device where sent

D10
data are stored
6-688
D100 for storing MsgID,

Starting device where received
D101 for storing the number of received packets
data are stored
D102…. for storing received data
Communication completion
M100
flag
Communication error flag M101
1. As M1 is on, set the MsgID of the sent message to 1 and MsgID of the received message to 2. Then the data
sending begins.
A. Sending the data in D10~D15 (6 bytes) to the slave is performed.
Device D10~D15
Content H0A (Defined by users)
B. The received response data from the slave are stored in D100~D109. M100 changes to On as the receiving is
done.
Device D100 D101 D102~D109
Content 2 8 H0B
6_
2. Master programming example
6-689
Example 2
Slave Mode
Using the CANRS instruction, the received data from the master are stored in the devices starting from D120 and the 8-
byte data in D20~D27 are sent back. M110 changes to On when the sending and receiving are over.
See the explanation of relevant parameters.
Slave mode_MsgID=1
Communication mode 2= Slave mode, sends data after receiving data.
MsgID of the sent message,

Communication ID
D0=2
Sent-data length 8 BYTE
Starting device where

D20
sent data are stored
D120 for storing MsgID

Starting device where
D121 for storing the number of received packets
received data are stored
D122…. for storing received data
Communication
M110
completion flag
_6
Communication error flag M111
1. As M1 is on, set the MsgID of the sent message to 2 and MsgID of the received message to 1 and then wait to
receive data.
A. The received 6-byte data from the master are placed in D120~D127.
Device D120 D121 D122~D127
Content 1 6 H0A
B. Then the 8-byte data in D20~D27 start to be sent back to the master. M110 changes to On as the data sending is
done.
Device D10~D15
Content H0B (Defined by users)
6-690
2. Slave programming example
6_
6-691
1820 DMVSH Mode ~ ErrCode Enabling Delta DMV detection and communication

Mode   
Start1    
Start2    
Ready 
ComNo   
Id_Ip   
Address   
Length   
Shoot1 
Shoot2 
RdData 
Ok    
Err    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Mode 
Start1 
Start2 
_6 Ready 
ComNo  
Id_Ip  
Address  
Length  
Shoot1 
Shoot2 
RdData  
Ok 
Err 
ErrCode  

- AS -
6-692
Symbol
Mode : The triggering and receiving method
Start1 : Trigger signal for starting set1
Start2 : Trigger signal for starting set2
Completion signal of when receiving response data from DMV is

Ready :
complete
A serial port or network communication port for the PLC to send or

ComNo :
receive data
Id_Ip : Serial communication station address or network IP of DMV
Address : Starting device where DMV data to be read are stored
Length : Length of the data to be read
Output signal when PLC notifies DMV to enable the detection of

Shoot1 :
set1
Output signal when PLC notifies DMV to enable the detection of

Shoot2 :
set2
Starting device where the data that the PLC receives from the DMV
RdData :
are stored
Ok : Communication success flag

6_
Err : Communication error flag
ErrCode : Communication error code
Explanation
1. The DMVSH instruction is applicable to AS series PLC with the firmware of V1.06.00 and later.
2. Mode sets the method through which the PLC triggers DMV including DMV1000 and DMV2000 and the receiving
method. There are 2 modes: 0 and 1 for option. If the setting exceeds the range, PLC will automatically run in mode
0.
3. Please refer to following example explanation for the function of Start1, Start2, Ready, Shoot1, Shoot2, RdData
and Ok and the process of detection triggering.
4. ComNo sets a communication port number of the PLC. The number 1 represents COM1, number 2 represents
COM2, number 11 represents Card1, number 12 represents Card2 and number 4 represents Ethernet port. If the
setting is not one of the numbers mentioned above or represents the communication port that the PLC does not
support, the error flag Err will change to On and the error code 16#0001 will show up.
6-693
5. Id_Ip sets the communication station address (Mac ID) of the slave DMV or network IP. Address is the
communication address where DMV detection result is read. Length is the length of the read detection data.
6. See the explanation of the values of ErrCode in the table below.
Error code Description Correction
16#0001 The specified communication port is incorrect. Specify a new communication port number.
16#0002 DMV response fault Check the communication address
16#0003 No response from DMV Check if the cable is connected properly or
DMV has been enabled.
16#0004 Waiting for the response from DMV; DMV Modify the timing of enabling DMV detection.
detection cannot be enabled repeatedly.
Example 1
Mode=0
Only set1 is used to trigger the DMV detection and receiving of DMV response data.
See the sequence control diagram below.
En
Start1
_6
Shoot1
Ready
Com.
send receive
port
Ok
       
Explanation of the timings:
 The DMVSH instruction is enabled.
 Set Start1 to On to notify the instruction to send the output signal Shoot1 (ON for about 10ms) and notify DMV to enable
the detection function.
 After DMV receives the trigger message, Ready is set from On to Off.
 Shoot1 is cleared to Off automatically by the PLC.
6-694
 After DMV detection is finished, Ready is set from Off to On. The PLC starts to judge if Ready is on after waiting for 1.5
times the input filtering time. The PLC receives the message that Ready changes from Off to On and sends a read
command via Modbus 0x03.
 The Ok flag is set to On after the PLC receives the communication data sent back from DMV. At the moment, the already
received data can be processed.
 The Start1 and Ok flags can be cleared to Off by manual.
 If the detection need be retriggered to execute, directly set Start1 to On to start the next-round DMV detection. (Return
to step 2 to continue.)
Example 2
Mode = 1
Set1 and set2 are used to trigger the DMV detection separately. But the communication data reading command can not
be sent until both Readys change to On. (The example is applicable to the two-camera DMV1000 detection.)
See the sequence control diagram below.
En
Start1 6_
Shoot1
Ready
Start2
Shoot2
Com.
port send receive
Ok
      
6-695
 The DMVSH instruction is enabled.
 Set Start1 to On to notify the instruction to send the output signal Shoot1 (which is on for about 10ms) and notify DMV
to enable the detection function of the first camera.
 After DMV receives the trigger message, Ready is set from On to Off.
 Shoot1 is cleared to Off automatically by the PLC.
 Set Start2 to On to notify the instruction to send the output signal Shoot2 (which is on for about 10ms) and notify DMV
to enable the detection function of the second camera.
 Shoot2 is cleared to Off automatically by the PLC.
 After DMV detection is finished, Ready is set from Off to On and the two detections are complete. Then the PLC sends
a read command via Modbus 0x03.
 The Ok flag is set to On after the PLC receives the communication data sent back from DMV. At the moment, the already
received data can be processed.
 The Start1, Start2 and Ok flags can be cleared to Off by manual. If the detection need be retriggered to execute, return
to step 2 to proceed.
_6
6-696

Execute the appointed communication number of
1821 DESO ComNo ~ ErrCode
the data exchange table once

ComNo   
ListNo   
OK    
Error    
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
ComNo  
ListNo  
OK 
Error 
ErrCode  

- AS -
Symbol
ComNo ： Communication port for data exchange
ListNo ： Communication number of the data exchange table

6_
OK ： Completion flag
Explanation
1. This instruction is available for PLC with FW V1.08.20 or later and ISPSoft V3.09.07 or later.
2. Make sure the data exchange table of the PLC CPU is already created before executing this instruction. If not, the
Error flag switches to ON and ErrCode is recorded as 1.
3. ComNo is the communication port for data exchange.
Communication Port COM1 COM2 Ethernet Card1 Card2
Number in decimal format 1 2 3 11 12
4. ListNo is the communication number of the data exchange table.
6-697
5. When the instruction is enabled, only the appointed communication number of the data exchange table will be
executed. When the communication is done and the slave device reponses with OK, the OK flag will be ON. The
corresponding SM of the communication number will be ON and the Error Code is recorded as 0.
6. Before executing this instruction, the system checks if the communication number to be executed is in cyclic
communication mode. If yes, this instruction will not be executed. The Error flag is ON. Error Code is recorded as 2.
0 No error or the transmission is complete.
1 The data exchange table or the communication number does NOT exist.
2 The connection of the data exchange table is started; do NOT start another connection again.
3 No response from the slaves.
4 Slave responds with a communication error.
5 The same communication port is in use.
The communication port does NOT exist or the communication card (AS-F232/422/485) is
6
NOT installed. .
7 The communication number of the data exchange table exceeds the setting rang (1~32).
8. The communication timeout is set in the data exchange table.
9. This instruction is suggested for applications where the slave device is better not to receive or be sent with
communication requests regularly. Since only one communication will be opened during the instruction execution,
you need to close the instruciton to start another communication if the same communicaitron port is being used.
_6 10. There is no limit on the number of times you execute the instruction but only one communication can be
established for each communication port. If you execute the insturcion again when the same comunicaiton port is
being used, the Error flag will be ON and the Error Code is recorded as 5.
Example:
When M0 is ON, the instruction starts to execute the number four communication of the data exchange table in COM1.
The data exchange table of COM1
6-698
6.19.3 Descriptions of the Communication-related Flags and

Registers
Communication-related flags (SM)
Flag
Description Action
COM1 COM2 Card 1 Card 2
Data sending request flag
If you want to use the instruction to send and
receive data, you must use the pulse instruction to You set the flag to ON, and
SM96 SM97 SM76 SM77 set the flag to ON. When the instruction is the system automatically
executed, the PLC sends and receives the data. resets it to OFF.
After sending the data, the system automatically
resets the flag to OFF.
The system automatically

When the flag is ON, the PLC is waiting to receive
SM98 SM99 SM78 SM79 sets the flag to ON and
the data.
resets it to OFF.
Reception complete flag
After receiving the data, the system automatically The system automatically
SM100 SM101 SM80 SM81 sets the flag to ON. When the flag is ON, the data sets the flag to ON, and
received can be processed. After processing the you reset it to OFF.
data received, you must to reset flags to OFF. 6_

Data receiving error flag The system automatically
SM102 SM103 SM82 SM83 An error occurs during receiving data using the sets the flag to ON, and
data receiving instruction. you reset it to OFF.
Communication timeout error flag
If you set the communication timeout (in SR) and The system automatically
SM104 SM105 SM84 SM85 no data is received after the timeout period, the flag sets the flag to ON, and
is ON. After the problem is solved, you must reset you reset it to OFF.
the flag to OFF.
The choice between the 8-bit processing mode and
the 16-bit processing mode You set the flag to ON and

SM106 SM107 SM86 SM87
ON: 8-bit processing mode reset it to OFF.
6-699
Flag
Description Action
Communication mode
ON: RTU mode

You set the flag to ON and
SM210 SM212 - - OFF: ASCII mode
reset it to OFF.
You can set this value in HWCONFIG in ISPSoft.
Not available for Card1 and Card 2.
Communication protocol changed flag
The communication protocol changes in
accordance with the setting values in SR. If the flag
is set to ON, the communication protocol changes
in accordance with the setting values in SR and
then the system automatically resets the flag to

You set the flag to ON and
SM209 SM211 SM90 SM91 OFF.
reset it to OFF.
NOTE: this change does not affect the parameters
that you set in HWCONFIG. When the PLC
is powered-on again, the PLC operates
according to the communication protocol
set in HWCONFIG.
_6
NOTE: the above flags are non-latching types.
6-700
Communication-related registers (SR)
Special data register

Description
SR201 SR202 SR176 SR178 Communication port address
Communication protocol
SR209 SR212 SR177 SR179 For details, please refer to the following table to set up the communication
format for a serial communication port.
Communication timeout, unit: ms
Suppose the setting value is larger than 0. When the PLC executes the
communication instruction and is in the receiving state, but no data is received

SR210 SR213 SR182 SR183 after the timeout period or the intervening time between two characters exceeds
the setting value, the timeout flag is ON. You can set the register to 0 to disable
communication timeout monitoring. See the MODRW instruction set between
100–32767 (ms).
Setting the communication format for a serial communication port
b0 Data length 7 (value=0) 8 (value=1)
00 ： None
b2-b1 Parity bits 01 ： Odd 6_

10 ： Even
b3 stop bits 1 bit (value=0) 2 bits (value=1)
0001 (16#1) ： 4800
0010 (16#2) ： 9600
0011 (16#3) ： 19200
0100 (16#4) ： 38400
0101 (16#5) ： 57600

b7-b4
0110 (16#6) ： 115200
0111 (16#7) ： 230400 Not available for RS-232
1111 (16#F) ： Self-defined*1
b8-b15 Undefined (reserved)
6-701
*1: You can set the baud rate in HWCONFIG in ISPSoft.
The data transmission speed is listed in the following table.
Baud rate (bps) RTU timeout timer (ms) Baud rate (bps) RTU timeout timer (ms)
4800 9 115200 1
9600 5 230400 1
19200 3 - -
38400 2 - -
57600 1 - -
_6
6-702
6.20 Other Instructions

6.20.1 List of Other Instructions
The following table lists the Other Instructions covered in this section.
API Function
instruction
16-bit 32-bit
1900 WDT –  Watchdog timer
1901 DELAY –  Delaying the execution of the program
1902 GPWM – – General pulse width modulation
1904 EPUSH –  Storing the contents of the index registers
1905 EPOP –  Reading data into the index registers
1906 INFO –  Reading the system data
6_
6-703
6.20.2 Explanation of Other Instructions
1900 WDT P ─ Watchdog timer

AS AS ─
Symbol
Explanation
1. This instruction resets the watchdog timer to monitor the operation of the AS Series PLC system.
2. If the program scanning time in the PLC exceeds 200 milliseconds, the error LED indicator is ON, and the PLC
stops running.
3. The watchdog timer acts in the following cases.
 The system is behaving abnormally.
 Program execution takes too much time, and therefore the scan time is longer than the watchdog timer
setting value. There are two way you can improve the situation.
_6 (a) Use the WDT instruction to reset the watchdog timer.
STEP0 END
WDT
t1 t2
(a) Refer to the ISPSoft User Manual for more information about changing the watchdog timer setting value.
6-704
Example
Suppose the program scanning time is 300 milliseconds. After the program is divided into two parts, and you insert the
instruction WDT between these two parts, the time it takes to scan either the first part of the program or the second part
of the program must be less than 200 milliseconds.
6_
6-705
1901 DELAY P S Delaying the execution of the program

S   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

AS AS ─
Symbol
S ： Delay
Explanation
This instruction delays the execution of the program following the DELAY instruction for a period of time specified in S.
The unit of S is 0.1 milliseconds.
Example
_6
When X0.0 is ON, the instruction delays the execution of the program following the DELAY instruction for two
milliseconds. That is, Y0.0 is ON and the states of Y0.0–Y0.15 are refreshed two milliseconds after the DELAY instruction
is executed.
6-706
Input X0.0
Out put Y0.0
T =2ms
Additional remarks
1. If S I less than 0, there is no delay.
2. If S is larger than 1000, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
3. You can adjust the delay according to the actual conditions of your equipment.
4. The delay can be larger than S due to communication or other influences.
6_
6-707
1902 GPWM S1, S2, D General pulse width modulation

S1       
S2    
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
D 

─ AS ─
Symbol
S1 ： Pulse width
S2 ： Pulse cycle
D ： Output device
Explanation
_6 1. This instruction outputs every pulse with a width specified by S1 and with a cycle specified by S2 from the device
specified by D.
2. The pulse width specified by S1 is t. t must be between 0–3276 milliseconds.
3. The pulse cycle specified by S2 is T. T must be between 1–32767 milliseconds, and S1 should be less than S2.
4. The S2+1 and S2+2 parameters are for system use. Please do not change them.
5. If S1 is less than 0, there is no pulse output. If S1 is larger than S2, the output device stays ON.
6. You can change S1 and S2 during the execution of this instruction.
7. If the conditional contact is not enabled, there is no pulse output.
Example
When the program is executed, the values in D0 and D2 are 1000 and 2000 respectively. When X0.0 is ON, the device
Y0.0 outputs the pulses illustrated below. When X0.0 is OFF, Y0.0 is OFF.
6-708
t =1000ms
Y0.0
T= 2000ms
Additional remarks
1. The instruction counts by the scan cycle. Therefore, the maximum error is one scan cycle. Besides, S1, S2, and
(S2-S1) should be larger than the scan cycle; otherwise, an error occurs when the GPWM instruction is executed.
6_
2. If you use the instruction in a function block or an interrupt task, an inaccurate pulse output occurs.
6-709
1904 EPUSH P D Storing the contents of the index registers

D DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  

AS AS ─
Symbol
D ： Device to store the value in the index registers
Explanation
1. This instruction stores the values in E0–E9 in the devices specified by D. The valid range for D is between 0–99.
The instruction is not executed for values that exceed the range.
2. The instruction uses sixteen devices, and the last six devices are for system use. If you execute the instruction and
the number of times the data is stored is n (the value in D), the instruction stores data in E0–E9 in D+(16*n+1)–
_6
D+(16*n+16), and increments the value in D to n+1.
3. The storage for the device D is 1601 (16x100+1).
4. This instruction uses a pulse instruction to interact with the stack, pushing a value onto the stack. Therefore, you
must reset the contact before the next operation.
5. When you use this instruction with the EPOP instruction (API 1905), the value stored last in the device specified by
D is read first, following the LIFO (last in first out) principle.
The num ber of ti mes

D t he dat a is stored .
D+1 E0
D+2 E1
......
......
D + 10 E9
For system u se
D +16
D +17 E0
D + 18 E1
D + 19 E2
......
......
6-710
Example
Suppose the value in D0 is 0.
When X0.0 is ON for the first time, the instruction transmits the data in E0–E9 to D1–D10 and increments the value in D0
to 1.
When X0.0 switches from OFF to ON for the second time, the instruction transmits the data in E0–E9 to D17–D26, and
increments the value in D0 to 2.
When X0.0 switches from OFF to ON for the nth time, the instruction transmits the data in E0–E9 to (n*16)+1–(n*16)+10.
Additional remarks
1. If the value in D is not between 0–99, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
2. If the range of devices is not sufficient for D+((the value in D)+1)*16-1), the instruction is not executed, SM0 is ON,
and the error code in SR0 is 16#2003. 6_
6 - 7 11
1905 EPOP P D Reading the data into the index registers

D DWORD 
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
D  

AS AS ─
Symbol
D ： Device from which the value is read
Explanation
1. This instruction reads the values in the devices specified by D into E0–E9, and decrements the value in D by one.
The valid value for D is between 1–100. The instruction does not execute values that exceed the range.
2. The instruction involves sixteen devices, and the last six devices are for system use. If you execute the instruction
and the number of times the data is stored is n (the value in D), the instruction stores the data in E0–E9 in
_6 D+16*(n-1)+1–D+16*(n-1)+10, and decrements the value in D to n-1.
3. This instruction uses a pulse instruction to interact with the stack, taking the TOP VALUE from the stack and
assigning it to the specified variable; therefore, you must reset the contact before the next operation.
4. The value that the instruction stores last in the device specified by D is read first, following the LIFO (last in first
out) principle.
The num ber of t im es

D t he data i s st ored .
D+1 E0
D+2 E1
......
......
D + 10 E9
F or syst em u se
D +16
D +17 E0
D + 18 E1
D + 19 E2
......
......
6-712
Example
When X0.0 is ON, the MOV instruction sets the value in D0 is set to 0, and the EPUSH instruction transmits the values in
E0–E9 to D1–D10. After the execution of FB0 is complete, the EPOP instruction reads the values in D1–D9 into E0–E9.
Additional remarks
6_
1. If the value in D is not in the range 0–100, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
2. If the range of device is not sufficient for D+((the value in D) *16-1), the instruction is not executed, SM0 is ON, and
6-713
1906 INFO P S，D Reading the system data

S 
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S  
D  

AS AS ─
Symbol
S: System-data reading code
D: Starting device where the read system data are stored
Explanation
_6
1. S is the system information reading code and the codes are listed in the following table.
Number of
consecutive D
S code No. Description devices Remark Supported version
(Number of
Words)
Reads the serial number 9 V1.04 and later

0 ASCII code
of the product
1 Reads Ethernet Mac ID 3 Hex value V1.04 and later
Reads already-power-on 2 32-bit value, unit: V1.04 and later

2
time minutes
0 The instruction is not

others Reserved
executed.
6-714
2. If the product serial no. is AS332T-AW16360001, the reading code of the instruction is 0 and the read data are
stored in the devices starting from D0, the product serial no. is stored in the order as below.
D0 D1 D2 D3 D4 D5 D6 D7 D8
16#5341 16#3333 16#5432 16#412D 16#3157 16#3336 16#3036 16#3030 16#0031
‘SA’ ‘33’ ‘T2’ ‘A-‘ ‘1W’ ‘36’ ‘06’ ‘00’ ‘1’
3. If Mac ID is 16#123456789ABC, the reading code of the instruction is 1 and the read data are stored in the devices
starting from D10, the Mac ID data are stored in the order as below.
D10 D11 D12
16#1234 16#5678 16#9ABC
4. If the already-power-on time is 70000 minutes (16#00011170), the reading code of the instruction is 2 and the read
data are stored in the devices starting from D20, the already-power-on time data are stored in the order as below.
D20 D21
16#1170 16#0001
5. Only the first-time execution of the INFO instruction is effective when the conditional contact is met. Therefore, it is
recommended to use the pulse instruction INFOP. If the INFO instruction is used with the normally-open contact
together, the instruction will be automatically executed only once.
6_
Additional remark:
If D is declared in a variable and the code is 0, 1 and 2, they can be declared respectively in ARRAY [9], [3], [2] of
WORD.
6-715
6.21 String Processing Instructions

6.21.1 List of String Processing Instructions
The following table lists the String Processing instructions covered in this section.

API Function
2100 BINDA DBINDA  Converting a signed decimal number into an ASCII code
Converting a binary hexadecimal number into an

hexadecimal ASCII code
Converting a binary-coded decimal number into an ASCII

code
Converting a signed decimal ASCII code into a signed

decimal binary number
Converting a hexadecimal ASCII code into a hexadecimal

binary number
Converting an ASCII code into a binary-coded decimal

number
2106 $LEN –  Calculating the length of a string

_6
2109 $FSTR – Converting a floating-point number into a string
2110 $FVAL –  Converting a string into a floating-point number
2111 $RIGHT –  Retrieving characters from a string starting from the right
2112 $LEFT –  Retrieving characters from a string starting from the left
2113 $MIDR –  Retrieving a part of a string
2115 $SER –  Searching a string
2116 $RPLC –  Replacing the characters in a string
2117 $DEL –  Deleting the characters in a string
2118 $CLR –  Clearing a string
2119 $INS –  Inserting a string
2122 SPLIT –  Splitting a string
2123 MERGE –  Merging strings
6-716
6.21.2 Explanation of String Processing Instructions
Converting a signed decimal number

2100 D BINDA P S, D
into an ASCII code

S           
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D  

AS AS AS
Symbol
S ： Source value
D ： Device where the conversion result is stored
6_
Explanation
1. This instruction converts the signed decimal binary number in S into an ASCII code, and stores the conversion
result in D.
2. The instruction supports SM690 to control the ending character.
3. For 16-bit instructions, the value in S must be a binary number and between -32768 to 32767. The operand D
occupies four word devices. The instruction converts the data is converted as follows.
b15 b0 b15 b7
b8 b0
1234  16#32 16#31 D+0
16#34 16#33 D+1
16#00 16#00 D+2
6-717
If SM690 is OFF, the instruction stores the ending character 16#0000 in D+2. If SM690 is ON, the value in D+2 is
unchanged without the ending character.
If the value in S is a positive value, the instruction stores only the value but not the sign character in D. If the value
in S is a negative value, the instruction stores the “-” sign character in D (16#2D). For example, if the value in S is -
12345 and SM690 is OFF, the conversion result is as follows.
b15 b0 b15 b7
b8 b0
-1234  16#31 16#2D（-） D+0
16#33 16#32 D+1
16#00 16#34 D+2
4. For 32-bit instructions, the value in S must be a binary number between -2147483648 to 2147483647. The
operand D occupies six word devices. The data is converted as follows.
b31 b0 b15 b7
b8 b0
12345678  16#32 16#31 D+0
16#34 16#33 D+1
16#36 16#35 D+2
16#38 16#37 D+3
16#00 16#00 D+4

_6
In addition, if the value in S is a positive value, the instruction stores only the value but not the sign character in D.
If the value in S is a negative value, the instruction stores the “-“ sign character in D (16#2D). For example, if the
value in S is -12345678, and SM690 is OFF, the conversion result is as follows.
b31 b0 b15 b7
b8 b0
-12345678  16#31 16#2D D+0
16#33 16#32 D+1
16#35 16#34 D+2
16#37 16#36 D+3
16#00 16#38 D+4
6-718
Example 1
Suppose the value in L0 is 5126 and SM690 is OFF. When the instruction executes, the values are D0=16#3135,
D1=16#3632, D2=16#0000.
D10 b15 b7
b8 b0
5126  16#31 16#35 D0
16#36 16#32 D1
16#00 16#00 D2
Example 2
Suppose the value in D10 is -3842563 and SM690 is OFF. When the instruction is executed, the values are
D0=16#332D, D1=16#3438, D2=16#3532, D3=16#3336, D4=16#0000.
6_
D10 b15 b7
b8 b0
-3842563  16#33 16#2D D0
16#34 16#38 D1
16#35 16#32 D2
16#33 16#36 D3
16#00 16#00 D4
Additional remarks
1. If value in the device D is not sufficient for the conversion, SM0 is ON, and the error code in SR0 is 16#2003.
6-719

Converting a binary hexadecimal number
2101 D BINHA P S, D
into a hexadecimal ASCII code

S           
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D  

AS AS AS
Symbol
S ： Source value
_6 Explanation
1. This instruction converts the hexadecimal binary number in S an ASCII code, and stores the conversion result in D.
3. For 16-bit instructions, the value in S must be between 16#0000–16#FFFF, and should be a four-digit binary
number. The operand D occupies three word devices.
If SM690 is OFF, 16#0000 is stored in D+2. If SM690 is ON, the value in D+2 is unchanged. For example, if the
value in S is 16#02A6 and SM690 is OFF, the conversion result is as follows.
b15 b0 b15 b7
b8 b0
02A6  16#32 16#30 D+0
16#36 16#41 D+1
16#00 16#00 D+2
4. For 32-bit instructions, the value in S must be between 16#00000000–16#FFFFFFFF, and should be an eight-digit
binary number. The operand D occupies five word devices.
If SM690 is OFF, 16#0000 is stored in D+4. If SM690 is ON, the value in D+4 is unchanged. For example, if the
value in S is 16#03AC625E and SM690 is OFF, the conversion result is as follows.
6-720
b31 b0 b15 b7
b8 b0
03AC 6251  16#33 16#30 D+0
16#43 16#41 D+1
16#32 16#36 D+2
16#31 16#35 D+3
16#00 16#00 D+4
Example 1
Suppose the value in D10 is 16#9C06 and SM690 is OFF. When the instruction executes, the values are D0=16#4339,
D1=16#3630, D2=16#0000.
D10 b15 b7
b8 b0
16#9C06  16#43 16#39 D0
16#36 16#30 D1
6_
16#00 16#00 D2
Example 2
Suppose the value in D10 is 16#7B3C581F and SM690 is OFF. When the instruction executes, the values are
D0=16#4237, D1=16#4333, D2=16#3835, D3=16#4631, D4=16#0000.
6-721
D10 b15 b7
b8 b0
16#7B3C 581F  16#42 16#37 D0
16#43 16#33 D1
16#38 16#35 D2
16#46 16#31 D3
16#00 16#00 D4
Additional remarks
1. For 16-bit instructions, if D+2 exceeds the device range, SM0 is ON, and the error code in SR0 is 16#2003.
_6
6-722

2102 D BCDDA P S, D
number into an ASCII code

S           
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S    
D  

AS AS AS
Symbol
S ： Source value
Explanation
1. This instruction converts a binary-coded decimal number in S into an ASCII code, and stores the conversion result 6_
in D.
3. The binary-coded decimal value in S used in the 16-bit instruction must be between 0–9999, and should be a four-
digit binary-coded decimal value. The operand D occupies three word devices. The data is converted as follows.
b15-12 b11-8 b7-4 b3-0 b15 b7

b8 b0
0 8 7 6  16#38 16#30 D+0
Thousands 16#36 16#37 D+1
Hundreds Tens Units
16#00 16#00 D+2
4. For 32-bit instructions, the binary-coded decimal value in S must be between 0–99999999, and should be an eight-
digit binary-coded decimal value. The operand D occupies five word devices. The data is converted as follows.
6-723
b31 b0 b15 b7
b8 b0
0876 5432  16#38 16#30 D+0
16#36 16#37 D+1
16#34 16#35 D+2
16#32 16#33 D+3
16#00 16#00 D+4
5. If SM690 is OFF, the instruction stores the ending character 16#0000 in D+5. If SM690 is ON, the value in D+5 is
6. Even if the first digit of binary-coded decimal value in S is 0, the instruction converts it into an ASCII code 0 (16#30).
Example 1
Suppose the binary-coded decimal value in D10 is 1295 and SM690 is OFF. When the instruction executes, the values
are D0=16#3231, D1=16#3539, D2=16#0000.
D10 b15 b7
b8 b0
_6 1295  16#32 16#31 D0
16#35 16#39 D1
16#00 16#00 D2
Example 2
Suppose the binary-coded decimal value in D10 is 00578352 and SM690 is OFF. When the instruction executes, the
values are D0=16#3030, D1=16#3735, D2=16#3338, D3=16#3235, D4=16#0000.
D10 b15 b7
b8 b0
0057 8352  16#30 16#30 D0
16#37 16#35 D1
16#33 16#38 D2
16#32 16#35 D3
16#00 16#00 D4
6-724
Additional remarks
1. For 16-bit instructions, if the value in S is not between 0–9999, the instruction is not executed, SM0 is ON, and the
error code in SR0 is 16#200D. The binary-coded decimal value is represented by the hexadecimal number, but
one of digits is not within the range between 0 and 9.
2. For 32-bit instructions, if the value in S is not between 0–99999999, the instruction is not executed, SM0 is ON,
and the error code in SR0 is 16#200D. The binary-coded decimal value is represented by the hexadecimal
number, but one of digits is not within the range between 0 and 9.
6_
6-725

Converting a signed decimal ASCII code
2103 D DABIN P S, D
into a signed decimal binary number

S      
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D    

AS AS AS
Symbol
S ： Source value
Explanation
_6 1. This instruction converts the signed decimal ASCII code in S into a signed decimal binary number, and stores the
2. For 16-bit instructions, the operand S occupies three word devices, and the decimal ASCII code in S must be
between -32768 to 32767. If the value in S is a string and does not include the ending character 16#00, the
conversion can be up to 5 digits (excluding the sign).
b15 b7 b15
b8 b0 b0
S+0 “2“ “1“  1234 D
S+1 “4“ “3“
S+2 16#00 16#00
3. If the first character is “ ” (a space), the sign is a positive sign. If the first character is “-”, the sign is a negative sign.
Take the string “2345” for example.
b15 b7 b15
b8 b0 b0
S+0 “2“ “-“  -2345 D
S+1 “4“ “3“
S+2 16#00 “5“
6-726
4. For 32-bit instructions, the operand S occupies six word devices, and the decimal ASCII code in S must be
between -2147483648 to 2147483647. If the value in S is a string and does not include the ending character
16#00, the conversion can be up to 10 digits (sign excluded).
b15 b7 b31
b8 b0 b0
S+0 “2“ “1“  1234567890 D
S+1 “4“ “3“
S+2 “6“ “5“
S+3 “8“ “7“
S+4 “0“ “9“
S+5 16#00 16#00
5. If the first character is “ ” (a space), the sign is a positive sign. If the first character is “-”, the sign is a negative sign.
Take the string “-234567890” for example.
b15 b7 b31
b8 b0 b0
S+0 ‘2‘ ‘-’  -234567890 D
S+1 ‘4‘ ‘3‘
S+2 ‘6’ ‘5‘
S+3 ‘8‘ ‘7‘
S+4 ‘0’ ‘9‘
S+5 16#00 16#00
6. If the first digit of the string in the device S is blank (16#20) + sign (16#2B), the value in S is processed as 0. For
6_
the second digit, if the number is not 0–9, the instruction treats it as the end of a string and no error message will
be shown. For example if the word order is 16#2016#3116#3216#2B, the conversion result is 12.
7. For 16-bit instructions, the string range in the device S is 1–6 (positive or negative signs included) and for 32-bit
instruction the range is 1–11 (positive negative signs included).
Example 1
Suppose the values are D20=16#302D, D21=16#3433, D22=16#0035. When the instruction executes, the value is D0=-
345.
6-727
b15 b7 b15
b8 b0 b0
D20 16#30 16#2D  -345 D0
D21 16#34 16#33
D22 16#00 16#35
Example 2
Suppose the values are D20=16#322D, D21=16#3433, D22=16#3635, D23=16#2037, D24=16#0000, D25=16#0000.
When the instruction executes, the value is D0=-234567.
b15 b7 b31
b8 b0 b0
D20 16#32 16#2D  -234567 D0
D21 16#34 16#33
D22 16#36 16#35
_6 D23 16#20 16#37
D24 16#00 16#00
D25 16#00 16#00
Example 3
Suppose the string value in S is 12. When the instruction executes, the value is D0=12.
6-728
Additional remarks
1. If the value of the first word in S is an ending character (16#00), the value is processed as 0 (16#30).
2. If the value of the first digit in S is 16#20 (blank) or 16#2B (+) or 16#2D (-) and the second digit is 16#00, the value
in S is processed as 0 (16#30).
3. Even if the first digit of binary-coded decimal value in S is 0, it is converted into the ASCII code 0 (16#30).
4. The value of the first digit in S only supports ASCII codes, 16#30–16#39 (0–9), 16#200 (blank), 16#2D (negative
sign), 16#2B (positive sign), 16#00 (ending character). If the value of the first digit in S is not ASCII code, the
5. Except the first digit, if the value of other digits in S are not ASCII codes, 16#30–16#39 or 16#00, the value in S is
processed as 16#00.
6. If the value in S exceeds the device range, SM0 is ON, and the error code in SR0 is 16#2003. The instruction is
not executed.
7. For 16-bit instructions, if you declare the operand S in ISPSoft, the data type is ARRAY [3] of WORD/INT.
6_
6-729

Converting a hexadecimal ASCII code into
2104 D HABIN P S, D
a hexadecimal binary number

S      
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D    

AS AS AS
Symbol
S ： Source value
_6 Explanation
1. This instruction converts a hexadecimal ASCII code in S into a hexadecimal binary number, and stores the
2. For 16-bit instructions, the operand S occupies two word devices. If the value in S is a string and does not include
the ending character 16#00, the conversion can be up to 4 digits (sign excluded). The hexadecimal ASCII code in
S must be between 0000–FFFF. If S is a string, the string must be between “0”–“FFFF”.
b15 b7 b15
b8 b0 b0
S+0 “A“ “5“  16#5A8D D
S+1 “D“ “8“
3. For 32-bit instructions, the operand S occupies four word devices. If the value in S is a string and does not include
the ending character 16#00, the conversion can be up to 8 digits (sign excluded). The hexadecimal ASCII code in
S must be between 00000000–FFFFFFFF. If S is a string, the string must be between “0”–“FFFFFFFF”.
6-730
b15 b7 b31
b8 b0 b0
S+0 “C” “5“  16#5CB8 07E1 D
S+1 “8“ “B“
S+2 “7“ “0“
S+3 “1“ “E“
4. The valid string range in the device S for 16-bit instruction is 1–4 and for 32-bit instruction it is 1–8.
Example 1
Suppose the values are D20=16#3641, D21=16#4633 (ASCII 16#A63F). When the instruction executes, the value is
D0=-22977.
b15 b7 b15
b8 b0 b0
6_
D20 16#36 16#41  16#A63F D0
D21 16#46 16#33
Example 2
Suppose the values are D20=16#4634, D21=16#3244, D22=16#3738, D23=16#3035 (ASCII 16#4FD28750). When the
instruction executes, the value is (D1, D0)=16#4FD28750.
6-731
b15 b7 b31
b8 b0 b0
D20 16#46 16#34  16#4FD2 8750 D0
D21 16#32 16#44
D22 16#37 16#38
D23 16#30 16#35
Example 3
Suppose the string value in S is A. When the instruction executes, the value is D20=16#A=10.
Example 4
_6 Suppose the values are D20=16#3641, D21=16#4600 (ASCII 16#00A6). When the instruction executes, the value is
D0=166.
b15 b7 b15
b8 b0 b0
D20 16#36 16#41  16#00A6 D0
D21 16#46 16#00
6-732
Additional remarks
1. If the ASCII code in S is not between 16#30–16#39 (“0”–”9”), or between 16#41–16#46 (“A”–”F”), the instruction is
6_
6-733

Converting an ASCII code into a binary-
2105 D DABCD P S, D

S      
D       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D    

AS AS AS
Symbol
S ： Source value
Device where the conversion

D：
result is stored
_6
Explanation
1. This instruction converts the ASCII code in S into a binary-coded decimal number, and stores the conversion result
in D.
2. For 16-bit instructions, the operand S occupies two word devices, and the ASCII code in S must be between 0000–
9999. If S is a string, the string must be between “0”–“9999”.
b15 b7 b15-b12 b11-b8 b7-b4 b3-b0
b8 b0
S+0 “8“ “9“  9 8 7 6 D
S+1 “6“ “7“ Thousands Hundreds Tens Units
6-734
3. For 32-bit instructions, the operand S occupies four word devices, and the ASCII code in S must be between
0000000–99999999. If S is a string, the string must be between “0”–“99999999”.
b15 b7 b15-b12 b11-b8 b7-b4 b3-
b8 b0 b0
S+0 “8“ “9“  5 4 3 2 D
S+1 “6“ “7“ 9 8 7 6 D+1
S+2 “4“ “5“
S+3 “2“ “3“
4. If the value in S is 16#20 the value is processed as 16#30. If the value in S is 16#00, the value is processed as an
ending character.
5. For 16-bit instructions, if S is a string, the number of characters contained in the string must be between 1–4. For
32-bit instructions, if S is a string, the number of characters contained in the string must be between 1–8.
Example 1
Suppose the values are D20=16#3820, D21=16#3637 (ASCII 876). When the instruction executes, the instruction
converts the value into Y0=16#876.

6_
b15 b7 b15-b12 b11-b8 b7-b4 b3-
b8 b0 b0
D20 16#38 16#20  0 8 7 6 Y0
D21 16#36 16#37
6-735
Example 2
Suppose the values are D20=16#3738, D21=16#3536, D22=16#3334, D23=16#3132 (ASCII 87654321). When the
instruction executes, the value is (D11, D10)= 16#87654321.
b15 b7 b31
b8 b0 b0
D20 16#37 16#38  8765 4321 D0
D21 16#35 16#36
D22 16#33 16#34
D23 16#31 16#32
Example 3
_6
Suppose the string value in S is 1. When the instruction executes, the value is D20=16#0001.
Example 4
Suppose the string value in S is 1234. When the instruction executes, the value is (D21, D20)= 16#00001234.
6-736
Additional remarks
1. If the ASCII code in S is not ASCII codes 16#30–16#39, 16#20, or 16#00, the instruction is not executed, SM0 is
2. If S is a string and the number of characters contained in the string exceeds the range, the instruction is not
6_
6-737
2106 $LEN P S, D Calculating the length of a string

S     
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D  

AS AS -
Symbol
S ： String
D ： Length of the string
Explanation
_6 1. This instruction calculates the length of the string in S, exclusive of the ending character (16#00), and stores the
length of the string in D.
2. The value stored in D must be between 0–32767. If it exceeds this range, the value in D is processed as 32767.
b15 b8 b 7 b0
S Sec ond char acter Fi rs t c haracter
S+1 F ourth c harac ter Thir d char acter b15 b0
S+2 Six th c harac ter Fifth charac ter n D
1 6#00 Length of the s tring

S+ n (En d ing c ha ract er) n thc harac ter
If the data in S-S+4 is ABCDEFGHI, the calculation result is as follows.
b15 b8 b7 b0
S 16#42( B) 16#41( A)
S+1 16#44( D) 16#43( C) ABCDEF GHI b15 b0
S+2 16#46( F) 16#45( E) 9 D
S+3 16#48( H) 16#47( G)
S+4 16#00 16#49( I)
( En di ng cha ra cter )
6-738
Example 1
1. Declare two symbols Test String and Len.
2. When M0 switches from OFF to ON, the instruction $LEN counts and stores the string length into the value in Len.
Additional remarks
1. If the string does not end with 16#00, the instruction executes to the maximum length of 32767.
2. If the length of the value exceeds the device range, the last character is processed as the ending character.
6_
6-739

Converting a floating-point number into a
2109 $FSTR P S1, S2, D
string

S1       
S2      
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1 
S2  
D  

AS AS -
Symbol
S1 ： Source value
S2 ： First device where the format is stored

First device where the conversion result is
D ：
stored
_6 Explanation
1. This instruction converts the floating-point number in S1 into a string in accordance with the format setting value in
S2, and stores the conversion result in D.
2. This instruction converts the floating-point number in S1 into a string and appends the ending character 16#00 to
the end of the string, and then stores the conversion result in D.
High byte Low byte
D Second ASCII code First ASCII code
（S1+1，S1） D+1 Fourth ASCII code Third ASCII code
 D+2 Sixth ASCII code Fifth ASCII code
Floating-point number …… ……
D +n-1 mth ASCII code m-1th ASCII code
D +n 16#00 ending character
Floating-point string
3. The conversion result varies with the setting of S2.
6-740
4. The value in S2+1 must be between 2≦S2+1≦20; the sign (+,-) and the digits in an integer or decimal number are
included but the decimal point in a decimal number and the exponent number are not included.
Operand Description
0: Decimal format
S2
1: Exponential
S2+1 Number of character
5. If the value in S1 is a positive number, the first ASCII code can be stored in D; if the value in S1 is a negative
number, the sign 16#2D (-) is stored first and then the second ASCII is stored.
6. Decimal format (S2=0)
After con ve rsio n,

the fl oa ting -p oin t string
in th e device D.
Sign Integ er . De ci ma l
 The value in S2+1 must be between 2≦S2+1≦20; the sign (+,-) and the digits in an integer or decimal
number are included but the decimal point in a decimal number and the exponent number are not included.
 Example 1
Suppose the number of characters is eight. Two floating-point numbers examples are -1.2345678 and
123456. The calculation is as follows.
D Floating-point number Floating-point number 6_

number -1.2345678 123456
D 16#31 (1) 16#2D (-) 16#32 (2) 16#31 (1)
D+1 16#32 (2) 16#2E (.) 16#34 (4) 16#33 (3)
D+2 16#34 (4) 16#33 (3) 16#36 (6) 16#35 (5)
16#00
D+3 16#36 (6) 16#35 (5)
ending character
16#00
D+4 16#38 (8)
ending character
After the conversion, if the floating-point number is stored in S2+1 but if the length exceeds the value in S2+1,
the instruction rounds off the digits in the decimal number. The floating-point string does not have to fill all of
S2+1.
6-741
 Example 2
After the conversion, if the floating-point number is stored in S2+1, the instruction uses the exponential
format to convert. For example, the number of characters is five digits and the floating-point number is
1234567, the conversion result is1.2346E+06.
D number
1234567
D 16#2E (.) 16#31 (1)
D+1 16#33 (3) 16#32 (2)
D+2 16#36 (6) 16#34 (4)
D+3 16#2B (+) 16#45 (E)
D+4 16#32 (6) 16#30 (0)
16#0000
D+5
ending character
 Example 3
After the conversion, if the floating-point number is stored in S2+1, the instruction uses the exponential
format to convert. For example, the number of characters is two digits and the floating-point number is
_6 0.00012345, the conversion result is1.2E-04.
D number
0.00012345
D 16#2E (.) 16#31 (1)
D+1 16#45 (E) 16#32 (2)
D+2 16#30 (0) 16#2D (-)
16#00
D+3 16#34 (4)
ending character
 Example 4
After the conversion, if the absolute value of the floating-point number is <=10-5, the instruction uses the
exponential format to convert. For example, the number of characters is four digits and the floating-point
number is 0.00001234, the conversion result is1.234E-05.
6-742
D number
0.00001234
D 16#2E (.) 16#31 (1)
D+1 16#33 (3) 16#32 (2)
D+2 16#45 (E) 16#34 (4)
D+3 16#30 (0) 16#2D (-)
16#00
D+4 16#35 (5)
ending character
7. Exponential format (S2=1)
After con ve rsio n, Si gn In tege r . De ci ma l Exponential

the fl oa ting -p oin t string
in th e device D.
 The value in S2+1 must be between 2≦S2+1≦20; the sign (+,-) and the digits in an integer and decimal
number are included but the decimal point in the decimal number and the exponent number are not included.
After calculation, the length adds the exponents (four digits) and the decimal point of the decimal number.
 The number of character in the area for the integer is one digit.
 The number of character in the area for the exponent is four characters. 6_
If the exponent is a positive number, the instruction adds 16#2B (+) in the area for exponent in D. If the
exponent is a negative number, the instruction adds 16#2D (-) in the area for exponent in D. The number of
character in the area for the exponent is two digits. If there is only one digit in the conversion result, the
instruction adds 16#30 (0) as the first digit of the area for the exponent.
 Example
Suppose the number of characters is eight. Two floating-point numbers examples are -123.456789 and
123456. The calculation is as follows.
Floating-point number Floating-point number

D number
-123.456789 12345
D 16#31 (1) 16#2D (-) 16#2E (.) 16#31 (1)
D+1 16#32 (2) 16#2E (.) 16#33 (3) 16#32 (2)
D+2 16#34 (4) 16#33 (3) 16#35 (5) 16#34 (4)
6-743
D+3 16#36 (6) 16#35 (5) 16#2B (+) 16#45 (E)
D+4 16#45 (E) 16#38 (8) 16#34 (4) 16#30 (0)
16#00
D+5 16#30 (0) 16#2B (+)
ending character
16#00
D+6 16#32 (2)
ending character
After the conversion, if the floating-point number is stored in S2+1, and the instruction rounds off the extra
digits.
The conversion result of the string length for the floating number -123.456789 in eight characters is 13 (the
ending character excluded).
The conversion result of the string length for the floating number 12345 in eight characters is 10 (the ending
character excluded).
The floating-point string does not have to fill all the characters.
Example 1
The floating-point number in (D1, D0= 12.3456) is converted into the decimal format in a string (D4=0, D5=8).
_6
D10 16#32（2） 16#31（1）
D11 16#33（3） 16#2E（.）
D12 16#35（5） 16#34（4）
16#00
D13 16#36（6）
ending character
6-744
Example 2
The floating-point number in (D1, D0 = 0.0012345678) is converted into the exponential format in a string (D4=1, D5=8).
D10 16#2E (.) 16#31 (1)
D11 16#33 (3) 16#30 (2)
D12 16#35 (5) 16#34 (4)
D13 16#37 (7) 16#36 (6)
D14 16#45 (E) 16#38 (8)
D15 16#30 (0) 16#2D (-)
16#00
D16 16#33 (3)
ending character
Additional remarks
1. If the value in S1 exceeds the range of values that can be represented by floating-point numbers, the instruction is 6_
2. If the value in S2 is neither 0 nor 1, the instruction is not executed, SM0 is ON, and the error code in SR0 is
16#2003.
3. If the value in S2+1 is not in between 2≦S2+1≦20, the instruction is not executed, SM0 is ON, and the error code
in SR0 is 16#2003.
6-745

Converting a string into a floating-point
2110 $FVAL P S, D
number

S       
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
D 

AS AS -
Symbol
S ： Source value
Explanation
1. This instruction converts a string in S into a floating-point number, and stores the conversion result in D.
_6
High byte Low byte
S Second ASCII code First ASCII code
S+1 Fourth ASCII code Third ASCII code （D+1，D）
S+2 Sixth ASCII code Fifth ASCII code 
…… …… Floating-point number
S +n-1 mth ASCII code m-1th ASCII code
16#00
S +n
ending character
Floating-point string
 Refer to the following sections for the ASCII code usage.
 For decimal or exponential formats, the maximum length for the floating-point string (m) is 24 characters
(excluding the ending character 16#00) and the maximum length of n is 13 characters.
2. The format of the value in S can be decimal or exponential. The instruction automatically determines the format
according to the value in S.
6-746
 Decimal format: the length for the floating-point string is nine; the ending character 16#00 is not included.
High byte Low byte
S 16#31 (1) 16#32 (2)
S+1 16#32 (2) 16#2E (.) D
S+2 16#34 (4) 16#33 (3)  21.234567
S+3 16#36 (6) 16#35 (5)
16#00
S+4 16#37 (7)
ending character
OR
High byte Low byte
S 16#31 (1) 16#2D (-)
S+1 16#32 (2) 16#2E (.) D
S+2 16#34 (4) 16#33 (3)  -1.234568
S+3 16#36 (6) 16#35 (5)
16#00
S+4 16#38 (8)
ending character
 Exponential format: the length for the floating-point string is 9; the ending character 16#00 is not included.
6_
High byte Low byte
S 16#31 (1) 16#2D (-)
S+1 16#32 (2) 16#2E (.) D
S+2 16#45 (E) 16#33 (3)  -1230
S+3 16#30 (0) 16#2B (+)
16#00
S+4 16#32 (3)
ending character
3. If the sign code in S is 16#20, 16#30, or 16#2B, then the conversion result is a positive value. If the sign code in S1
is 16#2D, then the conversion result is a negative value.
6-747
Example 1
D0 16#31 (1) 16#32 (2)
D1 16#32 (2) 16#2E (.) （D11，D10）
D2 16#34 (4) 16#33 (3)  21.234567
D3 16#36 (6) 16#35 (5)
16#00
D4 16#37 (7)
ending character
Example 2
_6
D0 16#31 (1) 16#2D (-)
D1 16#32 (2) 16#2E (.) （D101，D100）
D2 16#45 (E) 16#33 (3)  -1230
D3 16#30 (0) 16#2B (+)
16#00
D4 16#32 (3)
ending character
6-748
Additional remarks
1. If the length of the string in S exceeds 25 bytes and does not end with 16#00, SM0 is ON, and the error code in
SR0 is 16#2003.
2. There are some rules for the value in S. if the value in S does not follow the rules, the instruction is not executed,
SM0 is ON and the error code in SR0 is 16#2003.
The first ASCII code: signs16#2B(+), 16#2D(-), blank16#20, and numbers 16#30(0)–16#39(9) are allowed.
If the first ASCII code is a sign or a blank, the second ASCII code must be a number.
The second ASCII code can be in either decimal or exponential format.
 Decimal format:
Integ er OR In tege r . D ecimal

The decimal point “,” (16#2E), can only occur once and there must be numbers before and after the decimal point.
 Exponential format:
Inte ger Exp one nt OR In tege r . De ci ma l Exp one nt

The decimal point “,” (16#2E), can only occur once and there must be numbers before and after the decimal point.
There must be a number before the exponent. 6_

Integers: only numbers “0” (16#30)–“9” (16#39) are allowed.
Decimals: only numbers “0” (16#30)–“9” (16#39) are allowed.
Exponents: The format for a four digit ASCII code is as below.
Fi rst Second
E OR e +OR- n umber
nu mb er
There must be an “E” (16#45) or ”e” (16#65) and it can only occur once.
There must be a sign “+”(16#2B) or “-” (16#2D) and it can only occur once.
There must be two digits; numbers “0” (16#30)–“9”(16#39).
6-749
3. If the string in S is out of range, the instruction is not executed, SM is ON, and the error code in SR0 is 16#2003.
 If the first character in the string is a number ”0”–”9” (16#30–16#39), the valid range for a floating-point string
is 1–24. The minimum length for the string is one.
 If the first character in the string is a blank (16#20) or a sign (“+”(16#2B) or “-” (16#2D)), the valid range for a
floating-point string is 2–24. The minimum length for the string is two (“+1”).
4. If the conversion result exceeds the range of values that can be represented by floating-point numbers, the
_6
6-750

2111 $RIGHT P S, n, D
beginning from the right.

S       
n          
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
n  
D  

AS AS -
Symbol
S ： String
n ： Number of characters to be retrieved
D ： Device where the characters retrieved are stored
6_
Explanation
1. This instruction retrieves n characters from the string in S from the right, and stores the retrieved characters in D.
When the data type of S (source value) is string, the maximum length for the value in S is 31 characters. When the
data type of S (source value) is not string, the maximum length for the value in S is 255 characters.
2. If n is 0, the value in D is 0. The maximum length for n is 255 characters. .
6-751
b15 b8 b7 b0
S Second A SCII code F irst ASCII code
S +1 F our th ASCII code T hi rd AS CII c ode
.. ... ... ... ... ... ... .
~
n-1 A SCII c ode from the last
th
n ASCII code fr om the las t
th

th
th
~
Second ASC II code from the last T hi rd AS CII c ode from the l as t
16#00 F irst ASC II code from the last
n-1 A SCII c ode from the last n ASCII code fr om the las t
th th
D
th
th
D +1
.....................
~
Second ASC II code from the last T hi rd AS CII c ode from the l as t
16#00 F irst ASC II code from the last
If the data in S is ABCDEF12345 and n is 5, the instruction retrieves five characters in the string in S from the right.
The conversion result is as follows.
b15 b8 b7 b0 b15 b8 b7 b0
S 16#42(B) 16#41(A) 16# 32(2) 16#31(1) D
S +1 16# 44(D) 16# 43(C) 16# 34(4) 16# 33(3) D +1
ABCDE F12345 S +2 16# 46(F ) 16# 45(E) 16#00 16# 35(5) D +2
S +3 16# 32(2) 16# 31(1)
S +4 16# 34(4) 16# 33(3) T he fifth charac ter from the last
S +5 16# 00 16# 35(5)
_6 Example
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#42(B) 16#41( A) 16# 46(F ) 16#45( E) D10
D1 16# 44(D) 16#43( C) 16# 48(H) 16# 47(G) D11
D2 16# 46(F ) 16# 45(E) 16# 00 D12
D3 16#48( H) 16#47( G) T he fourth char ac ter from the last
D4 16# 00
6-752
Additional remarks
1. If the operand S is not a string ($) but a device with a string, the string in S can be up to 256 characters (16#00
ending character included). If the string in S does not end with 16#00, SM0 is ON, and the error code in SR0 is
16#200E.
2. If n is less than 0, it is processed as 0. If n is greater than the length of the string in S, it is processed as the length
of the string is S.
3. If D is not sufficient to contain n characters, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
6_
6-753

2112 $LEFT P S, n, D
beginning from the left.

S       
n          
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S   
n  
D  

AS AS -
Symbol
S ： String
n ： Number of characters to retrieve
_6
Explanation
1. This instruction retrieves n characters from the string in S starting from the left, and stores the retrieved characters
in D. When S is a string device, the maximum length for the value in S is 31 characters; when the S is not a string
device, the maximum length for the value in S is 255 characters.
2. If n is 0, the value in D is 0.
b15 b8 b7 b0 b15 b8 b7 b0
S Second ASCII code F irst ASCII code Second ASCII code F irst ASCII code D
S +1 F our th ASCII code T hi rd A SCII c ode F our th ASCII code T hi rd A SCII c ode D +1
.....................
...........
~
n-1 A SCII code from the last

th
th
th
th
n+1 AS CII c ode from the last

th
n ASCII c ode from the l as t
th
n ASCII c ode from the l as t
th
16#00
~
16#00 Last A SCII c ode
If the data in S is ABCDEF12345 and n is 7, the instruction retrieves seven characters in the string in S from the
left. The conversion result is as follows.
6-754
b15 b8 b7 b0 b15 b8 b7 b0
S 16#42(B) 16#41( A) 16# 42(B) 16#41( A) D
S +1 16# 44(D) 16# 43(C) 16# 44(D) 16# 43(C) D +1
ABCDEF 12345 S +2 16# 46(F ) 16# 45(E) 16# 46(F ) 16# 45(E) D +2
S +3 16# 32(2) 16# 31(1) 16# 00 16# 31(1) D +3
S +4 16# 34(4) 16# 33(3) Seventh c haracter
S +5 16# 00 16# 35(5)
Example
When M0 is ON, the instruction retrieves the six characters starting from the character in D100, and stores them in D10.
b15 b8 b7 b0 b15 b8 b7 b0
D0 6 D100 16#42(B) 16#41( A) 16# 42(B) 16#41( A) D10
D101 16# 44(D) 16# 43(C) 16# 44(D) 16# 43(C) D11
D102 16# 46(F ) 16# 45(E) 16# 46(F ) 16# 45(E) D12
Six th charac ter D103 16# 48(H) 16#47( G) 16# 00 D13
D104 16# 00
Additional remarks
6_
1. If the operand S is not a string ($) but a device with a string, the string in S can be up to 256 characters(16#00
ending character included). If the string in S does not end with 16#00, SM0 is ON, and the error code in SR0 is
16#200E.
2. If n is less than 0, it is processed as 0. If n is greater than the length of the string in S, it is processed as the length
of the string is S.
3. If D is not sufficient to contain n characters, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
6-755
2113 $MIDR P S1, S2, D Retrieving a part of a string

S1       
S2       
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2  
D  

AS AS -
Symbol
S1 ： String
S2 ： Part of the string to be retrieved
_6 Explanation
1. Suppose the values in S2 and S2+1 are n and m respectively. This instruction retrieves m characters starting from
the nth character in the string in S1, and stores them in D.
b15 b8 b7 b0 b15 b8 b7 b0
S1 Se con d AS CII co de First ASCI I c ode n+ 1

th
AS CII co de f rom th e las t n t h A SCII c ode from t he las t D
n+ 3 AS CII co de f rom th e las t
th
S1+1 Fourt h AS CII cod e Third A SCII co de n+ 2 t h AS CII co de f rom th e las t D +1
. .. .. .. . .. .. .. . .. .. ..
.. .. .. .. ...
~
n+ 1 t h AS CII co de f rom th e las t n t h A SCII c ode from t he las t n+ m-2 t h AS CII co de f rom th e las t n+ m-3 t h AS CII co de f rom t he las t
n+ 2 t h AS CII co de f rom th e las t n+ m-1 AS CII co de f rom th e las t
th
n+ 3 t h AS CII co de f rom th e las t 16#0 0
~
n+ m th ASCI I c ode fro m the las t n+ m-1 AS CII co de f rom th e las t

th
~
16#0 0 Las t ASCI I c ode
6-756
2. If the data in S1 is ABCDEFGHIJK, the value in S2 is 3, and the value in S2+1 is 7, the instruction retrieves the
seven characters starting from the third characters in the string from the left. The conversion result is as follows.
b15 b8 b7 b0 b15 b8 b7 b0
S1 16#42(B) 16#41(A) 16# 44(D) 16# 43(C) D
S1 +1 16# 44(D) 16# 43(C) 16# 46(F ) 16#45(E) D+1
S2
S1 +2 16# 46(F ) 16# 45(E) 16# 48(H) 16# 47(G) D+2
Thi rd cha ra cter D+3
S1+3 16# 48(H) 16# 47(G) 16# 00 16# 49(I)
S1 +4 16# 4A(J ) 16# 49(I)
16# 00 16# 4B(K) Se ven th ch ar acte r
S1+5
3. If the value of S2 is S2<=0, S2+1<-1or S2+1=0, the instruction is not executed.
4. If the value in S2+1 is -1, the instruction retrieves the characters in S1 starting from the character indicated by the
value in S2 to the last character in S1.
5. If the data in S1 is ABCDEFGHIJK, the value in S2 is 5, and the value in S2+1 is -1, the conversion result is as
follows.
b15 b8 b7 b0 b15 b8 b7 b0
S1 16#42(B) 16#41( A) 16# 46(F ) 16#45( E) D
S1 +1 16# 44(D) 16# 43(C) 16# 48(H) 16# 47(G) D +1
S1 +2 16# 46(F ) 16# 45(E) 16# 4A(J ) 16# 49(I) D +2
S1+3 16# 48(H) 16# 47(G) Fifth c harac ter 16# 00 16# 4B(K)
S1 +4 16# 4A(J ) 16# 49(I)
6_
S1+5 16# 00 16# 4B(K)
Example
b15 b8 b7 b0 b15 b8 b7 b0
D10 16#32(2) 16#31( 1) 16# 34(4) 16#33( 3) D0
D11 16# 34(4) 16# 33(3) 16# 36(6) 16# 35(5) D1
D12 16#36( 6) 16# 35(5) 16# 00 D2
D13 16# 00 16# 37(7)
D20 3
D21 4
6-757
Additional remarks
1. If the operand S1 is not a string ($) but a device with a string, the string in S1 can be up to 256 characters (16#00
ending character included). If the string in S1 does not end with 16#00, SM0 is ON, and the error code in SR0 is
16#200E.
2. If the value of S2 is S2<=0 or S2+1<-1, SM0 is ON, and the error code in SR0 is 16#2003.
3. If the value in S2 or S2 + S2+1 is larger than the length of the string in S1, SM0 is ON, and the error code in SR0 is
16#2003.
4. If the value in S2+1 is larger than the number of characters that can be retrieved from the string in S1, SM0 is ON,
5. If D is not sufficient to contain S2+1 characters, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
6. if you declare the operand S2 in ISPSoft, the data type is ARRAY [2] of WORD/INT.
_6
6-758
2115 $SER P S1, S2, n, D Searching a string

S1       
S2       
n          
D      
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2   
n  
D  

AS AS -
Symbol
S1 ： String to be searched
S2 ： String to be searched for
n ： nth character in S2 where the search begins
D ： Search result 6_
Explanation
1. This instruction searches the string in S2 from the nth character for the string in S1, and stores the search result in
D.
2. When the nth character exceeds the length of the string in S2, or S1>S2, D is 0.
3. Suppose the string in S2 is “ABCDEFGHIJK”, the string in S1 is “EFGH”, and n is 3. The search begins from the
third character in S2, and the value in D is 5.
b15 b8 b 7 b0 b15 b8 b 7 b0
S1 1 6#46 (F ) 1 6#45(E) 16#4 2(B) 16#4 1(A) S2
S1 +1 1 6#4 8(H ) 1 6#47 (G) 16#4 4(D ) 16#4 3(C ) S2 +1 Se arch ing t he st ring f rom the th ird chara ct er
S1 +2 忽略
Ig n o r e d 16 #00 16 #46(F) 16# 45(E) S2+2
Matchin g chara ct er
16 #48(H) 16# 47(G) S2 +3
16# 4A(J) 1 6#4 9(I ) S2+4
16 #00 16# 4B(K) S2+5
Afte r the inst ruction is e xecuted
5 D
6-759
Example
b15 b8 b7 b0
16#32(2) 16#31( 1) D0
AB 16# 44(D) 16# 43(C) D1
Searc hing the str ing from the thi rd c har acter
16# 42(B) 16#41( A) D2
Matching c har acter
16# 48(H) 16# 47(G) D3
Ignored 16# 00
After the instruction is ex ecuted
5 D100
Additional remarks
1. If the operand S1 is not a string ($) but a device with a string, the string in S1 can be up to 256 characters(16#00
_6 ending character included). If the string in S1 does not end with 16#00, SM0 is ON, and the error code in SR0 is
16#200E.
2. If the operand S1 is not a string ($) but a device with a string, the string in S2 can be up to 256 characters(16#00
ending character included). If the string in S1 does not end with 16#00, SM0 is ON, and the error code in SR0 is
16#200E.
3. If n is less than or equal to 0, SM0 is ON, and the error code in SR0 is 16#2003.
6-760
2116 $RPLC P S1, S2, S3, S4, D Replacing the characters in a string

S1       
S2       
S3          
S4          
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2   
S3  
S4  
D  

AS AS -
Symbol
String to be searched and matching
S1 ：
characters replaced
S2 ： New string
S3 ： Number of characters in S1 to be replaced 6_

The string S2 replaces the characters in S1 starting from the
S4 ：
character indicated by the value in S4.
Explanation
1. This instruction replaces the characters in S1 with the characters in S2, starting from the character in S1 that
matches the character in S4. The number of characters that are replaced is indicated by the value in S3, and the
instruction stores the result in D.
2. For example, the instruction replaces the four characters starting from the sixth character in the string
“1234567890” with “MN”, and the result is “12345MN0”.
6-761
b15 b8 b7 b0 b15 b8 b7 b0
S1 16#32(2) 16#31( 1) 16# 32(2) 16#31( 1) D
S1+1 16# 34(4) 16#33( 3) 16# 34(4) 16# 33(3) D+1
S1+2 16# 36(6) 16# 35(5) 16# 4D(M) 16# 35(5) D+2
S1+3 16# 38(8) 16# 37(7) After the instruction 16# 30(0) 16# 4E(N) D+3
S1+4 16# 30(0) 16# 39(9) is executed 16# 0000 D+4
S1+5 Ignored 16# 00
S2 16# 4E(N) 16#4D( M)

S2+1 Ignored 16# 00
S3 4 Number of characters which are r eplaced
S4 6 Character which i s r eplaced
3. If the string in S2 is 16#00, the instruction deletes the matching characters.
4. If the value in S3 is larger than the number of characters that the instruction can replace in the string in S1, the
instruction replaces the characters in S1 starting from the character indicated by the value in S4 to the last
character in S1.
5. If the value in S3 is equal to 0, the instruction is not executed.
Example
When M0 is ON, the data in D0–D7 is “1234ABAB1234AB”, and the data in D10–D11 is “CDEF”. When the $RPLC
_6 instruction executes, the instruction replaces the characters in D0–D7 starting from the character indicated by the value
in D51 with the characters in D10–D11. The number of characters to replace is indicated by the value in D50, and the
instruction stores the result in D20–D27.
6-762
If the values in D50 and D51 are 3 and 4 respectively, the execution result is as follows.
b 15 b8 b7 b0
b15 b8 b7 b0
D0 16# 32 (2) 16#31(1)
1 6#32(2) 16#31 (1) D20
D1 16# 34 (4) 1 6#33(3) A f te r t he in s t ruc t io n 1 6#43(C) 16# 33 (3) D21
D2 16# 42(B) 16 #41(A) is ex ec u t ed.
16#45(E) 16#44(D) D 22
D3 16#42(B) 16 #41(A )
執行後 16# 41 (A) 1 6#46(F) D23
D4 1 6#32(2) 1 6#31(1) 16# 31 (1) 16# 42 (B) D 24
D5 1 6#34(4) 1 6#33(3)
16# 33 (3) 16# 32 (2) D 25
D6 1 6#42(B) 16#41(A) 16#41(A) 16# 34 (4 ) D 26
D7 Ig忽略
n o re d 16 #00 1 6#00 16# 42 (B) D 27
D10 16# 44 (D) 1 6#43(C)

D11 16# 45 (F ) 1 6#45(E)
D12 I 忽略
g n or ed 16 #00
D50 3 取代數量
N u m b e r o f c h ar ac t er s w h ic h a r e r e p la c e d
D 51 4 開始取代的位置
C h a r a c t e r w h ic h i s r e p la c e d
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#32(2) 16#31( 1) 16# 32(2) 16#31( 1) D20
D1 16# 34(4) 16# 33(3) 16# 43(C) 16# 33(3) D21
D2 16# 42(B) 16# 41(A) 16# 45(E) 16# 44(D) D22
D3 16# 42(B) 16# 41(A) 16# 42(B) 16# 46(F ) D23
D4 16# 32(2) 16# 31(1) 16#32 (2) 16#31 (1) D24
is executed
D5 16# 34(4) 16# 33(3) 16# 34(4) 16# 33(3) D25
D6 16# 42(B) 16# 41(A) 16# 42(B) 16#41 (A) D26
Ignored
6_
D7 16#00 16# 0000 D27
D10 16# 44(D) 16# 43(C)

D11 16# 45(F ) 16# 45(E)
D12 Ignored 16#00
D50 4 Number of characters which are r eplaced
D51 4 Character which is r epl ac ed
6-763
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#32(2) 16#31(1) 16# 32(2) 16#31(1) D20
D1 16# 34(4) 16# 33(3) 16# 43(C) 16# 33(3) D21
D2 16# 42(B) 16# 41(A) 16# 45(E) 16# 44(D) D22
D3 16# 42(B) 16# 41(A) After the instruction 16# 00 16# 46(F ) D23
D4 16# 32(2) 16# 31(1) is executed
D5 16# 34(4) 16# 33(3)
D6 16# 42(B) 16# 41(A)
D7 Ignored 16# 00
D10 16# 44(D) 16# 43(C)

D11 16# 45(F ) 16# 45(E)
D12 Ignored 16# 00
D50 20 Number of characters which are replaced
D51 4 Character which i s r eplaced
If the values in D50, D51, and D10 are 3, 4, and 16#00 respectively, the execution result is as follows. The three
characters in D0-D7 starting from the fourth character are deleted.
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#32(2) 16#31(1) 16# 32(2) 16#31(1) D20
D1 16# 34(4) 16# 33(3) 16# 41(A) 16# 33(3) D21
D2 16# 42(B) 16# 41(A) 16# 31(1) 16# 42(B) D22
D3 16# 42(B) 16# 41(A) After the instruction 16# 33(3) 16# 32(2) D23
D4 16# 32(2) 16# 31(1) is executed 16# 41(A) 16# 34(4) D24
D5 16# 34(4) 16# 33(3) 16# 00 16#42(B) D25
D6 16# 42(B) 16# 41(A)
D7 16# 00
_6 D10 16# 00
D50 3 Number of character s which are replaced
D51 4 Character which i s r eplaced
Additional remarks
1. If the string in S1 does not end with 16#00, SM0 is ON, and the error code in SR0 is 16#200E.
3. If the value in S3 <0 or S4<=0 or the value in S4 is larger than the length of the string in S1, SM0 is ON, and the error
4. If the value in the string (16#00 the ending character included) in S1 after the replacement is larger than 256, the
6-764
2117 $DEL P S1, S2, S3, D Deleting the characters in a string

S1       
S2          
S3          
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2  
S3  
D  

AS AS -
Symbol
S1 ： String
S2 ： Number of characters to be deleted

Characters in S1 are deleted starting from the character
S3 ：
indicated by the value in S3.
D ： Device where the execution result is stored
6_
Explanation
1. This instruction deletes the characters in S1 starting from the character indicated by the value in S3. The number of
characters that are deleted is indicated by the value in S2, and the instruction stores the result in D.
2. For example, the instruction deletes the four characters starting from the third character in the string “1234567890”
in S1, and stores the result “127890”in D.
b15 b8 b7 b0 b15 b8 b7 b0
S1 16#32(2) 16#31( 1) 16# 32(2) 16#31( 1) D
S1 +1 16# 34(4) 16# 33(3) 16# 38(8) 16# 37(7) D +1
S1 +2 16# 36(6) 16# 35(5) 16# 30(0) 16# 39(9) D +2
S1+3 16# 38(8) 16# 37(7) After the instruction 16# 0000 D +2
S1 +4 16# 30(0) 16# 39(9) is executed
S1 +5 Ignored 16# 00
S2 4
S3 3
6-765
3. If the value in S2 is larger than the number of characters which can be deleted in the string in S1, the instruction
deletes the characters in S1 starting from the character indicated by the value in S3 to the last character in S1, and
stores 16#00 in D.
b15 b8 b7 b0
S1 16#32(2) 16#31(1)
S1 +1 16# 34(4) 16# 33(3) b15 b8 b7 b0
16# 32(2) 16#31(1) D
S1 +2 16# 36(6) 16# 35(5)
D +1
S1+3 16# 38(8) 16# 37(7) After the instruction 16# 0000
S1 +4
is executed
16# 30(0) 16# 39(9)
S1 +5 Ignored 16# 00
Larger than the number of charac ter s

10
S2 which can be deleted i n the str ing in S1
S3 3
4. If the value in S2 is equal to 0, the instruction is not executed.
Example
When M0 is ON, the data in D0–D3 is “1234567”. When the $DEL instruction executes, it deletes the characters in D0–
D3 starting from the character indicated by the value in D11. The number of characters to delete is indicated by the value
in D10, and the instruction stores the result in D20–D23.
_6
b15 b8 b7 b0
D0 16#32(2) 16#31( 1) b15 b8 b7 b0
D1 16# 34(4) 16# 33(3) 16# 32(2) 16#31( 1) D20
D2 16# 36(6) 16# 35(5) 16# 37(7) 16# 33(3) D21
D3 16# 00 16# 37(7) 16# 00 D22
is executed
D10 3
D11 4
If the values in D10 and D11 are 5 and 4 respectively, the execution result is as follows. Note that the number of
characters to delete exceeds the range, the instruction deletes the characters in D0–D3 starting from the fourth character
to the last character.
6-766
b15 b8 b7 b0
D0 16#32(2) 16#31( 1)
b15 b8 b7 b0
D1 16# 34(4) 16# 33(3)
16# 32(2) 16#31( 1) D20
D2 16# 36(6) 16# 35(5) D21
After the instruction 16# 00 16# 33(3)
D3 16# 00 16# 37(7)
is executed
D10 5 Ex ceeding the range
D11 4
b15 b8 b7 b0
D0 16#32(2) 16#31(1)
b15 b8 b7 b0
D1 16# 34(4) 16# 33(3)
16# 37(7) 16#36(6) D20
D2 16# 36(6) 16# 35(5) D21
16# 00
D3 16# 00 16# 37(7) After the instruction
is executed
D10 5
D11 1
Additional remarks
2. If the value in S2 is less than 0, the value in S3 is less than or equal to 0, or the value in S3 is larger than the length
of the string in S1, SM0 is ON, and the error code in SR0 is 16#2003.
6_
6-767
2118 $CLR P S Clearing a string

S  DWORD   
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

AS AS -
Symbol
S ： String to be cleared
Explanation
_6 1. This instruction clears the string in S. If the string in S does not end with 16#00, the instruction clears up to 255
characters.
b15 b8 b7 b0
S 16#31(1) 16# 2D(-) S 16# 0000
S +1 16# 33(3) 16# 32(2) S +1 16# 0000
S +2 16# 34(4) 16# 35(5) S +2 16# 0000
S +3 16# 36(6) 16# 2E(.) S +3 16# 0000
S +4 16# 38(8) 16# 37(7) After the instruction S +4 16# 0000
is executed 16# 0000
S +5 16# 00 S +5
6-768
Example
The instruction clears the string in D0 as illustrated below.
b15 b8 b7 b0
D0 16#32(2) 16#31(1) 16# 0000 D0
D1 16# 34(4) 16# 33(3) 16# 0000 D1
D2 16# 36(6) 16# 35(5) 16# 0000 D2
D3 16# 00 16# 37(7) After the instruction 16# 0000 D3
is executed
6_
6-769
2119 $INS P S1, S2, S3, D Inserting a string

S1       
S2       
S3          
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2   
S3  
D  

AS AS -
Symbol
S1 ： String
S2 ： String to be inserted
S3 ： The string S2 is inserted into S1 after the character indicated by the value in S3.
D ： Device in which the execution result is stored

_6
Explanation
1. This instruction inserts the string in S2 into the string in S1 after the character indicated by the value in S3, and
2. If the string in either S1 or S2 is a null string, the instruction stores the other string (S1 or S2) that is not a null string
in D.
3. If the strings in S1 and S2 are null strings, the instruction stores 16#0000 in D.
b15 b8 b7 b0 b15 b8 b7 b0
S1 16#32(2) 16#31( 1) 16# 32(2) 16#31( 1) D
S1 +1 16# 34(4) 16# 33(3) 16# 34(4) 16# 33(3) D +1
S1 +2 16# 36(6) 16# 35(5) 16# 36(6) 16# 35(5) D +2
S1+3 16# 38(8) 16# 37(7) 16# 4E(N) 16# 4D( M) D +3
S1 +4 16# 30(0) 16# 39(9) 16# 38(8) 16# 37(7) D +4
is executed
S1 +5 16# 00 16# 30(0) 16# 39(9) D +5
16# 00 D +6
S2 16# 4E(N) 16# 4D( M)
S2 +1 16# 00
S3 6
6-770
Example
When M0 is ON, the data in D0–D3 is “1234567”, and the data in D10 is “AB”. When the $INS instruction executes, it
inserts “AB” into the string in D0–D3 after the character indicated by the value in D30, and stores the result in D20–D24.
If the value in D30 is 1, the execution result is as follows.
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#32(2) 16#31( 1) 16# 41(A) 16#31( 1) D20
D1 16# 34(4) 16# 33(3) 16# 32(2) 16# 42(B) D21
D2 16# 36(6) 16# 35(5) 16# 34(4) 16# 33(3)
6_
D22
D3 16# 00 16# 37(7) After the instruction 16# 36(6) 16# 35(5) D23
is executed 16# 00 16# 37(7) D24
D10 16# 42(B) 16# 41(A)
D11 Ignored 16# 00
D30 1
If the value in D30 is 0, the execution result is as follows.
b15 b8 b7 b0 b15 b8 b7 b0
D0 16#32(2) 16#31(1) 16#42(B) 16 #41(A) D20
D1 16#34(4) 16#33(3) 16#32(2 ) 16 #31(1) D21
D2 16#36(6) 16#35(5) Af ter 16#34(4) 16 #33(3) D22
execution 16# 36(6)
D3 16#00 16#37(7) 16 #35(5) D23
16#00 16 #37(7) D24
D10 16#42(B) 16#41(A)
D11 I gnored 16#00
D30 0
6-771
Additional remarks
3. If the value in S3 is less than 0, or if the value in S3 is larger than the length of the string in S1, SM0 is ON, and the
4. If the inserted value in the string (16#00 the ending character included) in S1 is larger than 256, the instruction is
_6
6-772
2122 SPLIT P S1，S2，S3，S4，D1，D2 Splitting a string

S1  
S2    
S3    
S4   
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2   
S3   
S4  
D1  
D2  
Pulse instruction 16-bit instruction 32-bit

i t ti
AS AS -
Symbol
S1 ： String
S2 ： Splitter
6_
S3 ： Designated ending character of a splitter
S4 ： Storing Length for a string after a splitter
D1 ： Device in which the string after a splitter is stored
D2 ： Device in which the quantity of split strings is stored
Explanation
1. This instruction is only available for firmware version 1.04 or later.
2. S1 is the string source. For characters in a string, only the characters before an ending character or the value in S3
will be used as a valid string.
3. S2 is the splitter that separates strings. S3 is a designated ending character of a splitter. Only values in the lower 8-
byte are valid for S2 and S3. However, if you input a value other than the value in the lower 8-byte, PLC does not
send any error message. When S2 and S3 use D devices to store values, only use lower 8-byte for values in ASCII
format. Values in S2 and S3 can be a constant number, an ASCII or a string.
4. S4 is the storing length for a string after a splitter; unit: WORD. The ending characters, such as 16#00 and 16#0000
6-773
should be included in the length. The maximum WORDs a string can contain is S4 and a WORD equals to 2 bytes.
An ending character 16#00 takes a byte. For example, if S4 is 2, the maximum WORDs a string can contain is 2
WORDs and 2 WORDs equals to 4 bytes. And that means a string can contain 3 characters and 1 ending character
(16#00). The setting range for S4 is 1-100. (If the input value is out of the range, the value will be seen as the
minimum or the maximum during operation and PLC does not send any error message.)
5. D2 is the sum of all the split strings.
6. The result of D1~ D1+ S4 *D2 –1 is the D devices that are occupied.
For example, if D2 is 3, that means the 1st string will be stored from D1+0 and the 2nd string will be stored in D1+ S4
and the 3rd string will be stored in D1+ S4 x2.
7. The instruction looks for a string for a length defined in S4 (WORD) till there is an ending character or a splitter. Add
1 to the value in D2. Whenever one string is found,
8. Up to 256 characters can be stored in S1 and up to 20 sets of strings can be stored in D2. When any of the limitation
is reached even when there is no ending character, the splitting stops.
Example
Use “,” as a splitter to split a string “abcd,1234,5.67,8910;ef” and use “;” as an ending character that stored in D0-D11. And
_6
store the results in the register starting from D100 in a unit of 10 WORDs.
Note: the string to be split does not include the characters “”.
6-774
Explanation
1. The results of this example D0~D11=“abcd,1234,5.67,89103;edf”.
Device Value String
D0 16#6261 “ba”
D1 16#6463 “dc”
D2 16#312C “1,”
D3 16#3332 32
D4 16#2C34 “,4”
D5 16#2E35 “.5”
D6 16#3736 “76”
D7 16#382C “8,”
D8 16#3139 “19”
D9 16#3330 “30”
D10 16#453B “e;”
D11 16#4644 “fd”
2. Starting contact is M0
3. The quantity of split strings D200=4
4. The split strings are as below.

6_
1st set: D100~D109 are
occupied; D100- D100 D101 D102 D103 D104 D105 D106 D107 D108 D109
D101=“abcd”
HEX 6261 6463 0000 0000 0000 0000 0000 0000 0000 0000
String “ba” “dc” 16#0000 - - - - - - -
2nd set: D110~D119 are
occupied; D110 D111 D112 D113 D114 D115 D116 D117 D118 D119
D110~D111=“1234”
HEX 3231 3433 0000 0000 0000 0000 0000 0000 0000 0000
String “21” “43” 16#0000 - - - - - - -
6-775
3rd set: D120~D129 are occupied; D120~D121=“5.67”
Device D120 D121 D122 D123 D124 D125 D126 D127 D128 D129
HEX 2E35 3736 0000 0000 0000 0000 0000 0000 0000 0000
String “.5” “76” 16#0000 - - - - - - -
4th set: D130~D139 are occupied, D130~D131=“89103”
Device D130 D131 D132 D133 D134 D135 D136 D137 D138 D139
HEX 3938 3031 0033 0000 0000 0000 0000 0000 0000 0000
Upper:
3”
String “98” “01” - - - - - - -
Lower:
16#00
Additional remarks
1. Up to 256 characters can be stored in S1 if there is no ending character (16#00) or splitter, the instruction will
execute on the 256 characters. SM0 will not be ON.
_6 2. Ending character 16#00 or 16#0000 will be added in a string after it is split (D1). See the example above.
3. Ending character 16#00 or 16#0000 will be added in a string after it is split (D1) even when there is no string behind
the split string.
6-776
2123 MERGE P S1，S2，S3，D1，D2 Merging strings

S1   
S2   
S3    
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1   
S2   
S3   
D1  
D2  
Pulse instruction 16-bit instruction 32-bit

i t ti
AS AS -
Symbol
S1 ： String source 1
S2 ： String source 2
S3 ： Splitter 6_
D1 ： Device in which the merged string is stored
D2 ： Device in which the quantity of merged strings is stored
Explanation
1. This instruction is only available for firmware version 1.04 or later.
2. S1 and S2 are the string source 1 and 2 respectively. S3 is the splitter that separates strings. Only values in the lower
8-byte are valid for S3. S1 merges S2 directly, when S3 is 0 (16#00). S1 adds the splitter and then merges S2, when
S3 is not 0.
3. D1 is where to store a merged string. The merging order is string 1 + splitter + string 2 + ending character 0 (16#00).
You can self-define an ending character. This self-defined ending character will be added before the official one, 0
(16#00).
4. If the values in S1, S2, S3 are all 0, D1 is 16#0000.
5. D2 is the sum of all the merged strings (ending character 16#00 excluded). The accumulated length for the string is
the length of string 1 or the length of string 1 + splitter + the length of string 2.
6-777
6. If the string sources for S1 and S2 are both 0 or when strings are merged, the length for the merged string is up to
255 words (ending character 16#00 excluded). For example, there are 250 words in String 1 and 100 words in
String 2. After they are merged, the length for the merged string is 250 words from String 1 + splitter *1 + first 4
words from String 2.
Example
Use “,” as a splitter to split a string and use “;” as an ending character and then merge 3 strings “abcd”, ”1234” and ”5.67”.
And store the results “abcd,1234,5.67;” D100=15, in the register starting from D0-D7.
_6 Explanation
1. Starting contact is M0
2. The 1st program: merge the 1st string “abcd” and 2nd string “1234” together and put a splitter “,” in between and then
store the result in the registers starting from D0.
The merged result: D0~D4= “abcd,1234”; the quantity of merged strings: D100=9
Device D0 D1 D2 D3 D4
HEX 6261 6463 312C 3332 0034
String “ba” “dc” “1,” “32” Upper 8-byte: 16#00 ; lower 8-byte: 4
3. The 2nd program: merge the 1st string D0=“abcd,1234” and 2nd string ”5.67” together and put a splitter “,” in between
and then store the result in the registers starting from D0.
The merged result: D0~D7= “abcd,1234,5.67”; the quantity of merged strings: D100=14
Device D0 D1 D2 D3 D4 D5 D6 D7
HEX 6261 6463 312C 3332 2C34 2E35 3736 0000
String “ba” “dc” “1,” “32” “,4” “.5” “76” 16#0000
6-778
4. The 3rd program: merge the 1st string D0=“abcd,1234,5.67” and 2nd string ”,” together and put a splitter “0” in between
(merge the string 1 and 2 directly) and then store the result in the registers starting from D0.
The merged result: D0~D7= “abcd,1234,5.67;”; the quantity of merged strings: D100=15.
Device D0 D1 D2 D3 D4 D5 D6 D7
HEX 6261 6463 312C 3332 2C34 2E35 3736 003B
Upper 8-byte: 16#00 ;

String “ba” “dc” “1,” “32” “,4” “.5” “76”
lower 8-byte: “;”
Additional remarks
3. If D1 + (D2+1)/2 – 1 exceeds the device range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#2003.
4. Ending character 16#00 or 16#0000 will be added behind the merged string. See the examples above.
6_
6-779
6.22 Ethernet Instructions

6.22.1 List of Ethernet Instructions
The following table lists the String Processing instructions covered in this section.

API Function
2200 SOPEN –  Opening a socket
2201 SSEND –  Sending data through a socket
2203 SCLOSE –  Closing a socket
2204 MSEND –  Sending an email
2206 INTOA –  Converting an integer IP address into a string IP address
2207 IATON –  Converting a string IP address into an integer IP address
2208 EIPRW – – Reading and writing EtherNet/IP data
2209 SCONF –  Setting the TCP/UDP Socket parameters
2210 MCONF –  Reading and writing Modbus TCP data
2211 EMCONF1 –  Setting email server parameter values
2212 EMCONF2 –  Setting email address
_6
6-780
6.22.2 Explanation of Ethernet Instructions
2200 SOPEN P S1，S2，S3 Opening a socket

S1         
S2         
S3         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  

AS AS -
Symbol
S1 ： Socket mode
S2 ： Socket number
S3 ： Communication mode
Explanation
6_6
1. This instruction opens a socket. Set S1 to 1 to open a TCP socket, and set S1 to 0 to open a UDP socket.
2. S2 is the socket number. It should correspond to the Ethernet socket number set in the advanced settings; up to 4
can be set.
3. The AS Series PLC functions as a client and sends a TCP connection (S1 = 1) request to the server if S3 is 1 or 3
(available for V1.06.30 or later), and the AS Series PLC functions as a sever and waits for a TCP connection (S1 =
1) request from the client if S3 is 0 or 2 (available for V1.06.30 or later).
4. To start a UDP connection (S1 = 0), set S3 to 0~3.
5. The operand S1 must be either 0 or 1 (default: 0); the operand S2 must be between 1–4 (default: 1); the operand S3
must be either 0 or 1 (default: 0). If exceeding the range, error code H’2003 shows on the PLC.
6. Before using the instruction, set the following setting in HWCONFIG in ISPSoft.
 PLC Parameter Setting → Ethernet-Basic → Setting IP address and netmask address
 PLC Parameter Setting → Ethernet-Advanced → Socket → Enable Socket Function
6-781
 PLC Parameter Setting → Ethernet-Advanced → Socket → TCP/UDP Socket Connection and Setting
sockets to be used
7. Refer to the SCONF instructions (API 2209) for more on the TCP and UDP Socket parameters.
8. If you need to send several data separately, you can use this new functionality: S3 = 2 or 3 (available for V1.06.30
or later). The first device in the receiving destination is stored with the length of the data to be received, and the data
to be received is stored from the second device and on. If you need to receive another data, you can clear the value
in the first device and start another data transmission.
9. When the TCP Socket (S1 = 1) is opened, use the following settings for S3, the Socket IP and communication ports.
Local Remote
Start
S3 Remote IP Communicatio Communicatio Description
Mode
n Port n Port
Specific IP Specifies IP address, local and

Not equal to 0 Not equal to 0
address remote communication port
Specific IP Specifies IP address, but not local

Not equal to 0 0
address communication port
Client 1 or 3
Any value 0 Any value Illegal; when PLC CPU is in Client
mode, the Server communication port
_6 0.0.0.0 Any value Any value and IP address should be appointed.
Specific IP Specifies IP address, but not remote

0 Not equal to 0
Specific IP Specifies IP address and local

Not equal to 0 Not equal to 0
Not specify IP address and local

0.0.0.0 0 Not equal to 0
Server 0 or 2 communication port
Not specify IP address, but to specify

0.0.0.0 Not equal to 0 Not equal to 0
remote communication port
Illegal; when PLC CPU is in Server,
Any value Any value 0 the Server communication port should
be appointed.
Note: New modes 2 and 3 are available for V1.06.30 or later. New modes use the first device in the receiving destination
to store the length of the data to be received. You can use the value here to determine if the receiving is complete. For
modes 0 and 1, no length of data will be recorded.
6-782
10. If data is sent through a TCP socket, and no error occurs after the instruction is executed, the socket starts to
establish the connection with the remote device and the flag for starting connection is ON. If the connection is
made successfully, the flag for successful connection is ON, and the flag for starting connection is OFF. If an error
occurs, the error flag is ON.
TCP
Connection Data Connection Connection Data
Socket Data Sent Error Flag
Started Received Starting Closed Sending
Number
1 SM1270 SM1271 SM1272 SM1273 SM1274 SM1275 SM1277
2 SM1278 SM1279 SM1280 SM1281 SM1282 SM1283 SM1285
3 SM1286 SM1287 SM1288 SM1289 SM1290 SM1291 SM1293
4 SM1294 SM1295 SM1296 SM1297 SM1298 SM1299 SM1301
11. If data is transmitted through a UDP socket, and no error occurs after the instruction is executed, the flag for
started connection is ON. If an error occurs, the error flag is ON.
UDP Socket Connection Connection

Data Received Data Sending Error Flag
Number Started Closed
1 SM1334 SM1335 SM1336 SM1337 SM1338
2 SM1339 SM1340 SM1341 SM1342 SM1343
3 SM1344 SM1345 SM1346 SM1347 SM1348

6_6
4 SM1349 SM1350 SM1351 SM1352 SM1353
12. If data is transmitted through a TCP Socket in Server mode or through a UDP Socket, it is not allowed to use the
following communication port number for AS series PLC.
Socket Type Communication Port Number Communication Protocol
TCP 80 HTTP
TCP 502 MODBUS TCP
TCP 44818 EtherNet/IP
UDP 68 DHCP/BOOTP
UDP 2222 EtherNet/IP
UDP 44818 EtherNet/IP
UDP 20006 Self-defined protocol for AS series
13. In general, the pulse SOPENP instruction is used.
6-783
Example 1 (S3 = 1)
1. This example illustrates how to establish a TCP connection between a computer as server and an AS Series PLC
as client.
2. ISPSoft → HWCONFIG (Ethernet-Basic)
Ethernet Configuration
IP Address Mode Static
IP Address 192.168.1.111
Netmask Address 255.255.255.0
Gateway Address 192.168.1.1
_6 3. a) ISPSoft → HWCONFIG (Ethernet-Advanced → Socket → 1st TCP Socket Connection)
b) SCONF instruction
1st TCP Socket Connection
Remote IP 192.168.1.110
Remote Port 3201
Local Port 3200
Send Data Address D1000
The defined length of data to be sent#1 200
Receive Data Address D2000
The defined length of data to be received#1 200
Keep Alive Timer 10

#1: This data length is defined by settings in SCONF instruction; for V1.06.20 or previous versions: 512 bytes are
available and for V1.06.30 or later versions: 4096 bytes are available.
4. First, set the parameters related to TCP Socket1 in HWCONFIG in ISPSoft or in the SCONF instruction.
6-784
5. Establishing a connection (Network 1); When M0 is ON, the system checks whether the socket is closed (SM1274
= ON), NOT connected (SM1270 = OFF), or NOT being connected (SM1273 = OFF). If the socket is not closed,
has not been connected, and is not being connected, the system performs the connection procedure. Once the
socket is connected (SM1270 = ON), M0 is switched to OFF.
6. Sending data (Network 3): When M1 is ON, the system checks whether the socket has been connected (SM1270
= ON), and no data is being sent yet (SM1275 = OFF). If the socket has been connected and no data is being sent,
the system starts to send the data. If the socket has not been connected, the system does not execute the
instruction. After the data has been sent (SM1272 = ON), M1 is switched to OFF.
7. Receiving data (Network 4): When M2 is ON, the system checks whether the socket has been connected and the
flag (SM1271) for data received is ON. If the socket has been connected and the flag for data received is ON, then
the data has already been received. But that does NOT necessary mean it has reached its maximum length of
receiving. After the data has been received (SM1271 = ON), M2 and SM1271 are switched to OFF.
8. Closing a connection (Network 5): When M3 is ON, the system checks whether the socket has been connected. If
the socket has been connected (SM1270 = ON), and the connection is not yet closed (SM1274 = OFF), the system
is going to close the connection. If the socket has not been connected, the system does not execute the
instruction. After the connection is closed (SM1274 = ON), M3 is switched to OFF.
6_6
6-785
Example 2 (S3 = 0)
1. This example illustrates how to establish an UDP connection between a computer and an AS Series PLC.
a) ISPSoft → HWCONFIG (Ethernet-Advanced → Socket → 1st UDP Socket Connection)
b) SCONF instruction
c) Refer to point 3 in Example 1 for setting up the connection.
2. Establishing a connection (Network 1); When M0 is ON, the system checks if the socket is closed (SM1334 = OFF)
and then the system performs the connection procedure. Once the socket is connected (SM1334 = ON), M0 is
switched to OFF.
3. Sending data (Network 3): When M1 is ON, the system checks if the socket has been connected (SM1334 = ON),
and then the system starts to send the data. After the data has been sent, M1 is switched to OFF.
4. Receiving data (Network 4): When M2 is ON, the system checks if the socket has been connected and the flag
(SM1335) for data received is ON. If so, the data has already been received. But that does NOT necessary mean it
has reached its maximum length of receiving. After the data has been received (SM1335 = ON), M2 and SM1335
are switched to OFF.
5. Closing a connection (Network 5): When M3 is ON, the system checks if the socket to be closed has been
connected (SM1334 = ON), and if the connection is not yet closed (SM1337 = OFF). If so, the system is going to
_6
close the connection. If the socket has not been connected, the system does not execute the instruction. After the
connection is closed, M3 is switched to OFF.
6-786
Example 3 (S3 = 2)
1. This example illustrates how a Server receives data of 2K byes from a TCP connection in mode S3 = 2.
2. SCONF instruction
1st TCP Socket Connection
Remote IP 192.168.1.106
Remote Port 0
6_6
Local Port 2020
Send Data Address D10000
The defined length of data to be sent#1 4096
Receive Data Address D15000
The defined length of data to be received#1 4096
Keep Alive Timer 30
#1: This data length is defined by settings in SCONF instruction; for V1.06.20 or previous versions: 512 bytes are
available and for V1.06.30 or later versions: 4096 bytes are available.
3. When PLC CPU is from STOP to RUN, execute SCONF instruction. Refer to API 2209 SCONF for setting up the
socket.
4. Establishing a connection (Network 3); When M0 is ON, the system checks if the socket is closed (SM1274 = ON),
NOT connected (SM1270 = OFF), or NOT being connected (SM1273 = OFF). If the socket is not closed, has not
been connected, and is not being connected, the system performs the connection procedure. Once the socket is
connected (SM1270 = ON), M0 is switched to OFF.
6-787
5. The connection to remote Client (IP = 192.168.1.106) is connected and sending 2K bytes of data.
6. Open the Monitor Table and start monitoring the starting device where the data length of the received data is
stored.
If 2K bytes of data is received, you can see the value in D15000 is 2000. If you need to start another data
transmission, you can set the value in D15000 to 0 to start another data length count.
7. Closing a connection (Network 5): When M3 is ON, the system checks if the socket has been connected. If the
socket has been connected (SM1270 = ON), the system is going to close the connection. If the socket has not
been connected, the system does not execute the instruction. After the connection is closed, M3 is switched to
OFF.
_6
6-788
Additional remarks
1. The following table lists TCP connection errors.
Error Code
Error Flag Description
(SR180)
16#2003 SM0 S1, S2, or S3 exceeds the range
16#600C SM1109 Local socket not used
16#600D SM1100 Ethernet network not connected
16#6200 TCP Socket error flag Illegal IP address
16#6201 TCP Socket error flag Illegal TCP Socket communication mode setting
16#6202 TCP Socket error flag Illegal TCP Socket mode setting
16#6203 TCP Socket error flag Illegal address for sending data
16#6204 TCP Socket error flag Length of sent data exceeds the range
16#6205 TCP Socket error flag Source data device exceeds the range
16#6206 TCP Socket error flag Illegal address for receiving data
16#6207 TCP Socket error flag Length of received data exceeds the range
16#6208 TCP Socket error flag Target data device exceeds the range
16#6212 TCP Socket error flag TCP Socket communication timeout

6_6
16#6213 TCP Socket error flag Size of data received larger than dataset
16#6214 TCP Socket error flag TCP Socket connection rejected by remote equipment
16#6215 TCP Socket error flag TCP Socket not connected
16#6217 TCP Socket error flag TCP Socket connection triggered
16#6218 TCP Socket error flag Sending data through TCP Socket triggered
16#621A TCP Socket error flag Disabling TCP Socket connection triggered
6-789
2. The following table explains UDP connection errors.
Error Code
Error Flag Description
(SR180)
16#2003 SM0 S1, S2, or S3 exceeds the range
16#600C SM1109 Local socket used
16#6209 UDP Socket error flag Illegal IP address
16#620A UDP Socket error flag Illegal communication mode
16#620C UDP Socket error flag Illegal address for sending data
16#620D UDP Socket error flag Length of sent data exceeds the range
16#620E UDP Socket error flag Source data device exceeds the range
16#620F UDP Socket error flag Illegal address for receiving data
16#6210 UDP Socket error flag Length of data received exceeds the range
16#6211 UDP Socket error flag Target data device exceeds the range
16#6213 UDP Socket error flag Size of data received larger than dataset
16#6215 UDP Socket error flag UDP Socket not connected
16#6217 UDP Socket error flag UDP Socket connection triggered

_6
16#6218 UDP Socket error flag Sending of data through UDP Socket triggered
16#621A UDP Socket error flag Disabling UDP Socket connection triggered
3. When the client and server are both AS Series PLC and the communication timeout settings are set the same, the
server automatically cuts the connection if a timeout occurs on the server first. In this case, the error flag on the
client is not ON. On the other hand, if a timeout occurs on the client first, the error flag on the client is ON and the
connection is cut.
6-790
2201 SSEND P S1，S2 Sending data through a socket

S1         
S2         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  

AS AS -
Symbol
S1 ： Socket mode
Explanation
1. This instruction sends data through the socket specified by S1. Set S1 to 1 to open a TCP socket, and set S1 to 0 to
open a UDP socket.

6_6
2. S2 is the socket number. It should correspond to the Ethernet socket number; up to 4 can be set.
3. The operand S1 must be either 0 or 1 (default: 0); the operand S2 must be between 1–4 (default: 1). If exceeding the
range, error code H’2003 shows on the PLC.
4. Before using this instruction, use the SOPEN instruction (API 2200) to open the socket. If the flag for the successful
connection of the TCP socket is ON, or the flag for started connection of the UDP socket is ON, use this instruction.
5. If data is sent through a TCP socket, and no error occurs after the instruction is executed, the data is sent, and the
flag for sending data is ON. If data is sent successfully, the flag for sent data is ON, and the flag for sending data is
OFF. If an error occurs, the error flag is ON.
TCP Socket Number Data Sending Data Sent Error Flag
1 SM1275 SM1272 SM1277
2 SM1283 SM1280 SM1285
3 SM1291 SM1288 SM1293
4 SM1299 SM1296 SM1301
6-791
6. If data is sent through a UDP socket, and no error occurs after the instruction is executed, the flag for sent data is
ON. If an error occurs, the error flag is ON.
UDP Socket Number Data Sending Error Flag
1 SM1336 SM1338
2 SM1341 SM1343
3 SM1346 SM1348
4 SM1351 SM1353
7. In general, the SSENDP pulse instruction is used.
Example
Refer to the example in the SOPEN instructions (API 2200).
Additional remarks
1. The following table explains TCP connection errors.
Error Code Error Flag Description
16#2003 SM0 S1 or S2 exceeds the range
_6 16#600D SM1100 Ethernet network not connected
16#6202 TCP Socket error flag Illegal TCP Socket mode setting
16#6203 TCP Socket error flag Illegal address for sending data
16#6204 TCP Socket error flag Length of sent data exceeds the range
16#6205 TCP Socket error flag Source data device exceeds the range
16#6212 TCP Socket error flag TCP Socket connection timeout
16#6214 TCP Socket error flag TCP Socket connection rejected by remote equipment
16#6215 TCP Socket error flag TCP Socket not connected
16#6218 TCP Socket error flag Sending of data triggered
6-792
16#620A UDP Socket error flag Illegal UDP Socket communication mode setting
16#620C UDP Socket error flag Illegal address for sending data
16#620D UDP Socket error flag Length of sent data exceeds the range
16#620E UDP Socket error flag Source data device exceeds the range
16#6218 UDP Socket error flag Sending of data triggered
6_6
6-793
2203 SCLOSE P S1，S2 Closing a socket

S1         
S2         
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  

AS AS -
Symbol
S1 ： Socket mode
Explanation
1. This instruction closes the socket specified by S1. Set S1 to 0 to close TCP socket, and set S1 to 1 to close UDP socket.
2. S2 is the socket number. It should correspond to the Ethernet socket number; up to 4 can be set.
_6 3. The operand S1 must be either 0 or 1 (default: 0); the operand S2 must be between 1–4 (default: 1). If exceeding the
range, error code H’2003 shows on the PLC.
4. Before closing the socket, make sure that the socket is connected or else the instruction is not executed.
5. If the client closes a TCP socket, the server continues to be connected to the local communication port (the flag for
successful connection is ON). If the server closes a TCP socket, the server is no longer connected to the local
communication port after the instruction is executed. When a TCP socket is closed, the corresponding flags are OFF.
6. After the instruction is executed to close a UDP socket, the corresponding flags are OFF.
7. If a TCP socket is closed, and no error occurs after the instruction is executed, the connection with the remote device
starts to close and the flag for closing connection is ON. If the connection is closed successfully, the flag for closing
connection is OFF. If an error occurs, the error flag is ON.
TCP Socket Number Connection Closed Error Flag
1 SM1274 SM1277
2 SM1282 SM1285
3 SM1290 SM1293
4 SM1298 SM1301
6-794
8. If a UDP socket is closed, and no error occurs after the instruction is executed, the flag for started connection is OFF.
If an error occurs, the error flag is ON.
UDP Socket Number Error Flag
1 SM1338
2 SM1343
3 SM1348
4 SM1353
9. In general, the pulse SCLOSEP instruction is used.
Example
Refer to the example for the SOPEN instruction (API 2200).
Additional remarks
1. The following table lists the TCP connection errors.
6_6
16#6212 TCP Socket error flag TCP Socket communication timeout
16#6214 TCP Socket error flag TCP Socket connection rejected by remote device
16#621A TCP Socket error flag Disabling TCP Socket connection triggered
16#621A UDP Socket error flag Disabling UDP Socket connection triggered
6-795
2204 MSEND P S1，S2，S3，D Sending an email

S1         
S2      
S3      
D     
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
D 

AS AS -
Symbol
S1 ： Remote email number
S2 ： Email subject
S3 ： Email body
D ： Completion of the instruction

_6
Explanation
1. This instruction creates and sends an email by setting S1, S2, and S3.
2. Before using the instruction, set the following values in ISPSoft.
 PLC Parameter Setting → Ethernet-Basic → Setting IP address and netmask address
 PLC Parameter Setting → Ethernet-Advanced → Email → Setting SMTP server, port, local email address,
and SMTP subject
 PLC Parameter Setting → Ethernet-Advanced → Email and Trigger Configuration → Setting email address
 If account identification is required: PLC Parameter Setting → Ethernet-Advanced → Email → Setting user
name and password
6-796
3. The email is set as follows.
Operand Description Setting Range
The value in S1 must be between 1–15.
Set Bit 0–bit 3 in ISPSoft to indicate the remote email addresses. You
Remote email can set up to four email addresses in ISPSoft. Bit 0 corresponds to
S1
number email 1, bit 1 corresponds to email 2, and so on.
If you want to send an email, you must set the corresponding bit in
ISPSoft.
S2 Email subject Size of email subject: up to 16 words
S3 Email body Size of email body: up to 64 words
Completion of the After the execution of the instruction is complete, the bit is ON. If the
D
instruction execution of the instruction is abnormal, the next bit (D+1) is ON.
4. In general, the MSENDP pulse instruction is used.
Example
Suppose the value in D0 is 00000101. When X0.0 is ON, the email is sent to email numbers 1 and 3. After the
communication with the SMTP sever is complete, M20 is ON. If no error occurs during the communication, M21 is OFF
and Y0.0 is ON.
6_6
6-797
Additional remarks
1. For the length of the string in S2 or S3, the system captures the data with the end of 16#00. If the length of the string
is larger than the maximum value (with 16#00 as the end), the length of the string in S2 or S3 is processed as the
maximum value.
3. Reserve one word between S2 and S3 for the interrupt character.
4. The following table explains errors in the execution of the email instruction.
1. D+1 exceeds device range

16#2003 SM0
2. S1<1 or S1>15
16#6100 D+1 Communication conflicts
16#6107 D+1 Email communication timeout
16#6108 D+1 Error in password authentication of SMTP server account
16#6111 D+1 Invalid remote email address
_6
6-798

Converting an integer IP address into a
2206 INTOA P S，D
string IP address

S  
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S  
D  

AS AS -
Symbol
S ： Source value
Explanation
1. This instruction converts the IP address in S and S+1 into a string IP address, and stores the conversion result in
D.
2. The operand D occupies eight consecutive devices.

6_6
Example
D 10 " 9" " 1"

D 11 "." "2 "
D 12 "6 " " 1"
Afte r th e in struction
D0 16 #C0( 192) 16#A8(16 8) D1 3
is exe cu ted "." "8 "
D1 16#00 ( 0) " 192.168.0.1"
16 #01 (1) D 14 " 0" " 0"
D 15 "." " 0"
D 16 "0 " "0 "
D1 7 16 # 00 "1 "
Additional remarks
6-799

Converting a string IP address into an
2207 IATON P S，D
integer IP address

S   
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S   
D  

AS AS -
Symbol
S ： Source value
Explanation
1. This instruction converts the string IP address in S into an integer IP address, and stores the conversion result in D
and D+1.
2. The operand S occupies eight consecutive devices.

_6
"192 .16 8. 0.1 "
S+ 0 " 9" "1 "

S+ 1 ". " "2 "
S+2 "6 " "1 " Af ter t he inst ruct ion
S+ 3 "8 " is e xecut ed D +0 16 #C 0(19 2) 16# A8(168 )
". "
S+ 4 " 0" "0 " D+1 1 6# 00 (0) 1 6#0 1 (0 1)
S+ 5 ". " "0 "
S+6 "0 " " 0"
S+ 7 1 6# 00 " 1"
3. There are 1–3 characters in every section of the string IP address in S. These sections are separated by “.”
(16#2E). For example, you can enter “192.168.0.1” instead of “192.168.000.001”.
4. The value of each section of the string IP address in S must be between 0–255.
6-800
Example 1
" 19 2. 16 8 .0 .1 "
D10 " 9" "1 "

D 11
". " "2 "
D 12 "6 " "1 "
Aft er t he instructio n
D1 3 ". " "8 " is e xe cute d D0 1 6# C 0(1 92 ) 16 #A 8(16 8 )
D1
D14 " 0" "0 " 1 6 #0 0 (0 ) 16 #0 1 (1 )
D15 ". " "0 "
D 16 "0 " " 0"
D1 7 1 6# 00 " 1"
Example 2
6_6
Af ter t he instruct ion

is e xecut ed
D0 1 6 #C0 (1 92 ) 16 #A 8(1 68 )
"1 92 .16 8.0 .1"
D1 16 #0 0( 0) 1 6# 01( 1)
Additional remarks
1. If the string in S does not end with 16#00, SM0 is ON, and the error code in SR0 is 16#200E.
2. In the string in S, except for the code representing the decimal point, the binary codes must be between 16#30–
16#39 or the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#2003.
3. If there are not three decimal points “.” in the string in S, the instruction is not executed, SM0 is ON, and the error
4. If the value of any section of the string IP address in S is not between 0–255, the instruction is not executed, SM0
5. The number of characters in any section of the string IP address in S must be between 1–3 or the instruction is not
6-801
_6
6-802
2208 EIPRW S1-S7，n，S，D1，D2 Reading and writing EtherNet/IP data

S1  
S2    
S3    
S4    
S5    
S6    
S7    
n    
S 
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1-D2 Refer to Explanation in the instruction.

- AS -
Symbol
S1-S7，n，S ： See Explanation below.
D1-D2 ： See Explanation below. 6_6
6-803
Explanation
1. This instruction reads and writes EtherNet/IP data. The following table lists the names and explanations of S1–S7,
n, S and D1–D2.
Operand Name Description Data Type Remarks
The first two sections of the IP address
occupy the first word and the remaining Occupies
two sections of the IP address occupy two

S1 IP address WORD[2]
the second word. For example, if the IP consecutive
address is 192.168.1.5, S1=16#C0A8 words
and S1+1=16#0105.
S2 Connection mode 0: UCMM WORD
Range: 16#0000–00FF. If the function

Function code
S3 code exceeds the range, the instruction WORD
(Service code)
is not executed.
S4 Class ID Refer to EtherNet/IP protocol. WORD
S5 Instance ID Refer to EtherNet/IP protocol. WORD
ON: Enable;
S6 Attribute ID switch BOOL
OFF: Disable
_6
S7 Attribute ID Refer to EtherNet/IP protocol. WORD
Length of read and write Size of the data to be written or read;

n WORD
data unit: byte; maximum: 200 bytes
Register for the Source register for the sent data or

S WORD[n]
read/write data where the received data is stored
0：Communication not triggered
1：Communication in process
2：Communication completed without

D1 Communication status WORD
errors
3：Communication error
4： Error in parameter setting
Occupies
Major error code and extended error two

D2 Error code WORD[2]
code consecutive
words
6-804
2. When you enable this instruction for the first time, it sends the communication command. If the number of
connected slaves reaches the upper limit, the communication status value in D1 is 3, and the communication
command is not sent. The error code shows16#6306 in D2[1] .
3. When the parameter exceeds the range, the instruction is not executed and the communication status value in D1
is 4.
4. This instruction should work with rising-edge trigger. If it is repeatedly triggered, the error code shows16#02 in
D2[0]. Wait till the execution of the instruction is complete before starting another instruction.
Example 1
The instruction reads the vendor code of the device at 192.168.1.5 and stores the value in D100. It sets the EtherNet/IP
Object parameters as shown below.
(1) Class ID = 1
(2) Instance ID = 1
(3) Attribute ID = 1
6_6
6-805
Example 2
The maximum frequency (01-00) of the AC motor drive (at 192.168.1.6) is set to 60.00Hz. The EtherNet/IP Object
parameters are set as shown below.
(1) Class ID = 16#0300
(2) Instance ID = 16#0001
(3) Attribute ID = 16#0000
_6
Additional remarks
1. If you declare the operand S1 in ISPSoft, the data type is ARRAY [2] of WORD.
2. If you declare the operand S in ISPSoft, the data type is ARRAY [n] of WORD, where n is the size of the
read/written data.
3. If you declare the operand D2 in ISPSoft, the data type is ARRAY [2] of WORD.
6-806
4. The following table explains the error codes in D2 [0].
Status
Description What to Do
Code
16#00 Connection successful
16#01 Connection error Ensure the EDS file of the slave is correct.
1. Ensure the number of devices connected to the master does
not exceed the limit.
2. Ensure the number of devices connected to the slave does

Connected devices
16#02 not exceed the limit.
unavailable
3. The instruction is triggered repeatedly. Wait till the execution
of the instruction is complete before starting another
instruction.
16#03 Error in parameter Ensure the read/written data in S is correct.
Ensure the settings are correct for Class ID (S4), Instance ID (S5),
16#04 Path error
and Attribute ID (S7).
Destination path does not Ensure the settings are correct for Class ID (S4), Instance ID (S5),
16#05
exist and Attribute ID (S7).
1. Ensure the Ethernet port of the slave device is connected
properly. 6_6
16#07 Connection broken
2. Ensure the keep alive timer setting is correct for the slave
device.
Service code not

16#08 Ensure the function code (S3) is correct.
supported
Ensure both the registers involved in reading/writing data and their

16#09 Invalid attribute value
contents are correct.
Ensure the slave device object attribute allows PLC to perform the
16#0A Error in attribute list
Get_Attribute_List and Set_Attribute_List functions.
16#0B Transmission conflicts Ensure the service setting is repeated.
16#0C Object status conflicts Ensure the Owner IO connection is established.
Ensure the slave supports the defined object. The service does not
16#0D Object existed
need to execute if the defined object is supported.
16#0E Attribute not writable Ensure the object attribute supports the write function.
6-807
Status
Description What to Do
Code
No privilege to perform
16#0F Ensure the slave device is allowed to perform the service code.
service code
Device cannot currently

16#10 Ensure the Owner IO connection is established.
perform service
Size of response data too Ensure the length of data in the object attribute does not exceed
16#11
large the limit (100 words).
Data access sequence
16#12 error when tag is Ensure the data length and the data type are correct.
accessed
Transmitted data too

16#13 Ensure the length (n) of read/written data is correct.
short
Attribute value Ensure the Attribute ID switch (S6) and Attribute ID (S7) are
16#14
unsupported correct.
Transmitted data are too

16#15 Ensure the read/written data length (n) is correct.
long
16#16 Object does not exist Ensure the Class ID (S4) is correct.
_6 Data access sequence

1. Ensure the Ethernet network connection is correct.
16#17 error when tag is
2. Ensure no packets are lost in the Ethernet communication.
accessed
16#18 Attribute value not stored Ensure no error state on the slave device occurred.
Attribute value storage

16#19 Ensure no hardware error on the slave device occurred.
error
Router error: length of

Ensure the read/written data length (n) does not exceed the limit of
16#1A request packet exceeds
the router.
limit
Router error: length of

Ensure the read/written data length (n) does not exceed the limit of
16#1B response packet exceeds
the router.
limit
User-defined object
16#1F Refer to the definition of the slave device error.
access error
16#20 Illegal parameter value Ensure the read/written value in S is correct.
6-808
5. The following table explains the error codes in D2 [0].
1. Value in S1, S2, S3, or S6 exceeds the range

16#2003 SM0 / D1
2. S+n out of range of the device address
16#200B SM0 Operand n out of range
16#6301 D1 Connection with remote device broken
16#6302 D1 Remote device response timeout
16#6303 D1 Illegal IP address
16#6304 D1 Error in response command service code
16#6305 D1 Error in response command length
16#6306 D1 Communication conflicts
6_6
6-809
2209 SCONF P S1-S10 Setting the TCP/UDP Socket parameters

S1    
S2    
S3    
S4    
S5    
S6    
S7    
S8    
S9    
S10    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1-S10 Refer to Explanation in the instruction.

AS AS -
Symbol
S1-S10 ： See Explanation below
_6
Explanation
1. This instruction sets the TCP/UDP Socket parameters. The following table lists the names and explanations of S1–
S10.
S1 TCP/UDP selection 0: TCP, 1: UDP WORD
S2 Socket number Range: 1–4 WORD
6-810
The first two sections of the IP address occupy

Occupies
the first word and the remaining two sections
two
S3 Remote IP address of the IP address occupy the second word. For WORD[2]
consecutive
example, if the IP address is 192.168.1.5,
words
S3=16#C0A8 and S3+1=16#0105.
S4 Remote port Range: 0–65535; 0 indicates any port WORD
S5 Local port Range: 0–65535; 0 indicates any port WORD
Specifies the number of a D device. Range: 0–
Register where 29999. Example: The setting value 100 means
S6 sent data comes S7 bytes of data are sent from the registers WORD
from starting at D100 (from the low byte to the high
byte).
Maximum: 512 bytes
S7 Size of sent data For PLC with FW V1.06.30 or later; maximum: WORD
4096 bytes
Specifies the number of a D device. Range: 0–
Register where 29999. Example: The setting value 200 means
S8 received data is S9 bytes of data are received and stored in the WORD
stored registers starting at D200 (from the low byte to 6_6

the high byte).
Maximum: 512 bytes

Size of received
S9 For PLC with FW V1.06.30 or later; maximum: WORD
data
4096 bytes
Applicable
S10 Connection time Range: 1–30000, unit: second WORD to TCP
mode only
2. In general, the SCONFP pulse instruction is used.
3. The Socket parameters uses the setting values in HWCONFIG by default. Use the SCONFP instruction when the
parameters need to be changed during communication.
4. If you set the parameters while the socket is communicating, the settings do not take effect until the communication
is complete. The setting should be changed after the socket is no longer in use.
5. If any one of the parameters is out of range, the instruction is not executed, SM0 is ON, and the error code in SR0
is 16#2003.
6 - 8 11
2210 MCONF P S1-S11 Reading/Writing Modbus TCP data

S1    
S2  
S3    
S4    
S5    
S6    
S7  
S8    
S9    
S10    
S11  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1-S11 Refer to Explanation in the instruction.

AS AS -
Symbol
S1-S11 ： See Explanation below
_6
6-812
Explanation
1. This instruction reads and writes Modbus TCP data. The following table lists the names and explanations of S1–
S11.
Data
Operand Name Description Remarks
Type
Modbus TCP data exchange table number,

S1 Data Exchange Table No. WORD
range: 1–32
The first two sections of the IP address
occupy the first word and the remaining Occupies
two sections of the IP address occupy the two

S2 Remote IP address WORD[2]
second word. For example, if the IP consecutive
address is 192.168.1.5, S2=16#C0A8 and words
S2+1=16#0105.
Range: 0–255. If the setting exceeds the

Station address of
S3 range, the value in the low byte is used WORD
remote slave
automatically.
Range: 16#01, 02, 03, 04, and 17.
If the function code is out of range,

S4 Read function code WORD
incoming parameters, including address
6_6
and data length, are not modified.
Read remote
S5 16#0000–16#FFFF WORD
Function code 16#01-02 for reading Bit
device, ranging from 1 to 256
Function code 16#03-04 for reading Word
device, ranging from 1 to 100

S6 Read data length WORD
When the setting value is 0 or less than 0,
this function is not enabled. If the setting
value is bigger than the maximum value, it
will be seen as the maximum value.
Function code for reading data in Bit
Local register where device; M device only BOOL

S7
received data is stored Function code for reading data in Word WORD
device; D device only
6-813
Data
Operand Name Description Remarks
Type
Range: 16#05, 06, 0F, and 10.
If the function code is out of range,

S8 Write function code WORD
outgoing parameters, including address
and data length, are not modified.
Write remote
S9 Range:16#0000–16#FFFF WORD
Function code 16#0F for writing Bit device,
ranging from 1 to 256; the value in function
code 16#05 can only be 1; for PLC with
FW V1.06.20 or later: 0 can be used in
16#05
Function code 16#10 for writing Word
device, ranging from 1 to 100; the value in

S10 Write data length WORD
function code 16#06 can only be 1; for
PLC with FW V1.06.20 or later: 0 can be
used in 16#05
When the setting value is 0 or less than 0,
_6 this function is not enabled. If the setting
value is bigger than the maximum value, it
will be seen as the maximum value.
Function code for writing data in Bit device;
Local register where M device only BOOL

S11
remote data is written Function code for writing data in Word WORD
device; D device only
2. In general, use the MCONFP pulse instruction.
3. The following points explain the Modbus communication function codes in S4 and S8.
When the AS Series PLC reads the data from multiple bit devices (not discrete input devices), the function code
sent is 1 (16#01).
When AS Series PLC reads the data from multiple bit devices (only discrete input devices), the function code sent
is 2 (16#02).
When the AS Series PLC reads the data from multiple word devices (not input registers), the function code sent is
3 (16#03).
6-814
When the AS Series PLC reads the data from multiple word devices (only input registers), the function code sent is
4 (16#04).
When the AS Series PLC writes the status to one bit device, the function code sent is 5 (16#05).
When the AS Series PLC writes the data to one word device, the function code sent is 6 (16#06).
When the AS Series PLC writes the status to multiple bit devices, the function code sent is 15 (16#0F).
When the AS Series PLC writes the data to multiple word devices, the function code sent is 16 (16#10).
When the AS Series PLC writes the data to multiple word devices, the function code sent is 23 (16#17).
At present, the AS Series PLC only supports the function codes listed above.
4. The parameters in the instruction are valid only while PLC is running. When PLC is powered back on after being
powered off, it takes the settings from the data exchange table by default. If you need to change some parameters
during data exchange, this instruction modifies those parameters.
5. If the specified socket is already communicating, the new parameters become effective after the current
communication is complete.
6. When any parameter is not within the valid range, the instruction is not executed, SM0 is ON, and the error code in
SR0 is 16#200B.
6_6
7. The AS Series PLC does not support the Modbus TCP communication instruction or anything similar to the
instruction ETHRW DVP series PLC. If you use the PLC program for Ethernet Modbus TCP communication
control, enable “Program control” mode in the data exchange table first and use the SM numbers from the following
table.
SM Number Attribute Explanation of Ethernet Data Exchange Parameters
SM1167 R/W Flag to enable data exchange
SM1168–SM1199 R/W Flag to enable data exchange connections 1–32
SM1200–SM1231 R Success flag for data exchange connections 1–32
SM1232–SM1263 R Error flag for data exchange connections 1–32
When data is received successfully, the success flag is ON. When there is an error receiving data, the error flag is
ON. The success flag and the error flag of any one connection socket are never switched to ON at the same time.
6-815
8. The following table explains the (read-only) SR numbers used in data exchange.
SR Number Explanation
SR1120–SR1151 Indicates the actual communication times for connections 1–32.
SR1152–SR1183 Indicate the communication error codes for connections 1–32.
The following table defines the error codes in SR1152–SR1183.
Error Code Explanation
16#00XX Remote device response error
16#F000 Ethernet network not connected
16#F001 Remote device response timeout
16#F003 TCP connection timeout
16#F007 Response command error
16#F009 Connection with remote device disconnected
_6
6-816

2211 EMCONF1 P Server ~ Passw Setting email server parameter values

Server   
Port    
LMail   
Sub   
Verify    
User   
Passw   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
Data
LINT
TMR
CNT
type INT
Refer to following instruction explanation

AS AS -
Symbol
Server~Passw : Refer to following explanation
6_6
6-817
Explanation
1. This instruciton is available for PLC with FW V1.06.00.
2. See the operand name, use explanation and data type in the following table.
Operand Name Explanation Data type Remark
Server +0: Data length, unit: bytes (0 or 4;
0: no modification)
Refer to Server
Server +1~ Server +2: data (Data are +0 for address
occupation.
placed from the lower 8 bits.) WORD[N]
3 consecutive
For example: 192.168.0.1,
words at most
Server Email server D0 = 16#0004, D1= 16#0001, D2= can be occupied.
16#C0A8;
Up to 15 words can be used in one string;
every section in one string can contain 1-3

String
words, and use a dot “.” to separate each
string, for example 192.168.0.1
Communication Range: 1~65535,

Port WORD
port 0: no modification
LMail +0: data length, unit: bytes (range:
0~63, 0: no modification.)
LMail +1~ LMail +32: data (Data are

Refer to LMail
placed from the lower 8 bits.)
+0 for address
_6 Local email For example: [email protected] WORD[N] occupation.
LMail 33 consecutive
address D0 = 16#000E, D1 = 16#7865, words at most
can be occupied.
D2 = 16#6440, D3 = 16#6C65,
D4 = 16#6174, D5 = 16#7777,
D6 = 16#2E63, D7 = 16#6D6F
Up to 63 words can be used in one string String
Sub +0: data length, unit: bytes (range:
Refer to Sub +0
Sub +1~ Sub +16: data content (Data are
for address
placed from the lower 8 bits.) WORD[N] occupation.
Sub Email subject 17 consecutive
For example: Sub words at most
can be occupied.
0 = 16#0003, D1 = 16#7553,
D2 = 16#0062
Enable/ disable 0: no modification, 1: Disable verification,

Verify WORD
verification 2: Enable verification
6-818

User +0: data length, unit: bytes (range:
Refer to User +0
User +1~ User +16: data content (Data
for address
are placed from the lower 8 bits.) WORD[N] occupation.
User User name 17 consecutive
For example: User words at most
can be occupied.
D0 = 16#0004, D1 = 16#7355,
D2 = 16#7265
Passw +0: data length, unit: bytes (range:
Refer to Passw
Passw +1~ Passw +10: data content +0 for address
occupation.
(Data are placed from the lower 8 bits.) WORD[N]
Passw Password 11 consecutive
For example: Passw
words at most
D0 = 16#0005，D1 = 16#5061， can be occupied.
D2 = 16#7373，D3 = 16#0077
You can set up the email related settings in ISPSoft > HWCONFIG > Device Setting > Ethernet Port Advance
Setting > Email. And from here you can also check the parameters which are set through instrucitons. But only the
settings that are set in ISPSoft are retainable after power-off.

6_6
6-819

2212 EMCONF2 P Index，Mail Setting email address

Index    
Mail   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
Data
LINT
TMR
CNT
INT
type
Refer to following instruction explanation

AS AS -
Symbol
Index, Mail : Refer to following explanation
Explanation
1. This instruciton is available for PLC with FW V1.06.00.
_6 2. See the operand name, use explanation and data type in the following table.

Index: The mail address number to be
Mail address
Index modified (Range: 0~4, 0: Not modify the WORD
number
mail address.)
Mail +0: the data length of Index value with
the unit of bytes (range: 0~63, 0: Not modify
the mail address.)
Mail +1~ Mail +32: The data content of

Refer to Mail +0
Index (Data are placed from the lower 8
for address
bits.) WORD[N] occupation.
Mail Mail address 33 consecutive
For example: [email protected] words at most
can be occupied.
D0 = 16#000E, D1 = 16#7865,
D2 = 16#6440, D3 = 16#6C65,
D4 = 16#6174, D5 = 16#7777,
D6 = 16#632E, D7 = 16#6D6F
6-820
You can set up the email related settings in ISPSoft > HWCONFIG > Device Setting > Ethernet Port Advance
Setting > Email. And from here you can also check the parameters which are set through instrucitons. But only the
settings that are set in ISPSoft are retainable after power-off.
6_6
6-821
6.23 Memory Card / File Register Instructions

6.23.1 List of Memory Card / File Register Instructions
The following table lists the Memory Card / File Register instructions covered in this section.

API Function
2300 MWRIT –  Writing data from the PLC into the memory card
2301 MREAD –  Reading data from the memory card into the PLC
2302 MTWRIT –  Writing a string into the memory card
2303 MEMW –  Writing data into the file register
2304 MDEL –  Deleting files on the memory card
_6
6-822
6.23.2 Explanation of Memory Card / File Register Instructions
2300 MWRIT P C, S, S1, S2, S3, S4 Writing data from the PLC into the memory card

C    
S  
S1    
S2    
S3   
S4    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data INT
type
C 
S 
S1 
S2 
S3 
S4 

AS AS -
Symbol 6_
C ： Control parameter
S ： Data source
S1 ： Data length
S2 ： Line advance
S3 ： File name
S4 ： Data address in the file
Explanation
1. This instruction writes data from the PLC to the memory card. The operands are described as follows.
 C: The control parameter
6-823
Item Code Description
Binary value
Default value
0
The file name extension is .dmd.
The unit of the value is a word.
The values are separated by a comma.
1 The file name extension is .cvs.
Use ASCII codes..
The value that is stored is a hexadecimal format.
The unit of the value is a double word.
Use ASCII codes.
The values are separated by a tab.

File format
_6
3 The file name extension is .txt.
Use ASCII codes.
Use ASCII codes.
The values are not separated by any mark.
Use ASCII codes.
6 The values are not separated by any mark.
6-824
The file name extension is .txt.
Use ASCII codes.
The values are separated by a comma. (V1.04.00 or later supports )
The unit of the value is a Word.
7 The file name extension is.csv.
Use ASCII codes.
The value that is stored is a decimal format.
Appending
The data that is written into the memory card is appended after the last
0 value in the file.
This is the default value
Function option If the file does not exist, it is created automatically.
Overwriting
The data that is written into the memory card replaces the values in the file
1
starting from the value indicated by the value in S4. 6_
If the file does not exist, it is created automatically.
Reserved - The values of bit 8–bit 15 are 0.
 S: The data source
 S1: The length of the data that the instruction writes into the file
If the value in S1 is 0, the instruction does not write any data into the file.
Item Description
If the file format is 0, 1, 3, 5, or 7, the unit of the value is a word. If the file format
Value unit
is 2, 4, or 6, the unit of the value is a double word.
Parameter unit Double word
The devices where the instruction stores the data cannot exceed the device
Length of the data range, and the size of the data that the instruction writes into the file cannot be
more than four gigabytes. Refer to Chapter 2 for more information about devices.
6-825
 S2: The line advance
The value in S2 must be between 0–256.
 AS series PLC with firmware version 1.04.00 or later supports using string (less than 9 characters) in the file
name S3.
 S3–S3+4: S3 occupies five devices. The file name contains a maximum of nine characters,
including 16#00. If the string does not end with 16#00, an error occurs. When the instruction
reads the ending character, it stops reading, and checks if the file name is legal. The characters in
the file name can be A–Z, a–z, and 0–9. The file name extension depends on the file format. The
file that the instruction creates is in the default folder. If the file name is “Test1”, the instruction
writes the characters into the devices as follows.
ASCII
S 'e' ' T' AS Code
CI I代碼
S 16#6 5 16 #54
S +1 't ' 's ' S +1 16 #74 16 #73
S+ 2 NUL '1' S+ 2 16 #00 16 #31
 The default folder path:
Model name Folder path
_6 AS300 Series PLC CARD\AS300\UserProg
AS200 Series PLC CARD\AS200\UserProg
 S4: The value in the file that the instruction overwrites is indicated by the value in S4.
Item Description
If the file format is 0, 1, 3, 5 or 7, the unit of the value is a word. If the file format is 2, 4,
Value unit
or 6, the unit of the value is a double word. (refer to operand C)
Parameter unit Double word.
If the function option is 0, S4 is not used.
If the function option is 1, the instruction replaces the values in the file with the data to
be written into the memory card starting from the value indicated by the value in S4.
Usage
The value in S4 must indicate a value in the file.
If the value in S4 is 0, the instruction overwrites the data in the file starting at the first
value in the file.
6-826
Flag Description
SM450 ON: the memory card is in the CPU module.
State of the write protection switch on the memory card
SM451 ON: the memory card is write protected.
OFF: the memory card is not write protected.
The data is being written from the PLC to the memory card, or the data is being read
SM452
from the memory card to the PLC.
ON: an error occurs during the operation of the memory card. If the flag is ON, you
SM453
must reset it to OFF. The error code is stored in SR453.
3. Related error codes (SR453):
16#005E An error occurs when the memory card is initialized.
16#005F The path is incorrect, or the file does not exist.
16#0060 The default folder cannot be created.
16#0061 The memory space is insufficient.

6_
16#0062 The memory card is write protected.
16#0063 An error occurs when the data is written into the file.
16#0064 The data cannot be read from the memory card.
16#0065 The file is a read-only file.
4. If the format of the target file on the memory card is 0, the format of the source file in the PLC must also be 0.
Otherwise, the instruction cannot read the data, and SM453 is ON. The same applies to the other file formats.
Example
SM450 is ON when you insert the memory card into the CPU module; SM452 is ON when the MWRIT instruction
executes; SM452 is OFF when the MWRIT instruction completes. You cannot use MWRITP (the pulse instruction)
continuously. Executing this pulse instruction to write data into the memory card continuously may exceed the writing
limitation and may lead to memory card damage.
6-827
Operand Setting value Description
The file into which the data is written
The file format:

D0 16#0011
The file name extension is .cvs.
Use ASCII codes.
D1 - The data that is written into the file
D10, D11 16#00000030 The size of the data that is written into the file is 48 words.
D300 16#000A Ten values are written into every line.
D20=16#6554
D20 D21=16#7473 The file name is “Test1”.

_6
D22=16#0031
The data that is written into the memory card replaces the values in the file
D30, D31 16#00000000
starting from the first value.
Additional remarks
1. If the value in C exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and the
2. If the value in S1 exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and the
6-828

Reading data from the memory card into
2301 MREAD P C, S, S1, S2, S3, D
the PLC

C    
S   
S1    
S2    
S3    
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
C 
S 
S1 
S2 
S3 
D 

AS AS -
Symbol
6_
S ： File name
S1 ： Data address in the file
S2 ： Reserved
S3 ： Data length
Explanation
1. This instruction reads data from the memory card into the PLC. The operands are described as follows.
6-829
Binary value
The default value is 0.

0
The file name extension is .dmd.
Use ASCII codes.
The value that is stored is a hexadecimal value.
Use ASCII codes.
File format The unit of the value is a word.

_6
Use ASCII codes.
Use ASCII codes.
Use ASCII codes.

6
6-830
Use ASCII codes.
The values are separated by a comma. (V1.04.00 or later supports )
The unit of the value is a Word.
7 The file name extension is.csv.
Use ASCII codes.
The value that is stored is a decimal format.
The values in the file starting from the value indicated by the value in S1 are read.
0
The default value is 0.
Function option The number of values is stored in D and D+1.
1 If the file format is 0, 1, 3, or 5, the unit of the value is a word. If the file format is 2, 4,
or 6, the unit of the value is a double word.
name S.
6_
 S–S+4: S occupies five devices. The file name contains a maximum of nine characters, including
16#00. If the string does not end with 16#00, an error occurs. When the instruction reads the
ending character, the instruction stops reading characters, and checks if the file name is legal. The
characters in a file name can be A–Z, a–z, and 0–9. The file name extension depends on the file
format. The file that the instruction creates is in the default folder. If the file name is “Test1”, the
instruction writes the characters into the devices as follows.
ASCII
S 'e' ' T' S 16#6 5 16 #54
AS Code
CI I代碼
S +1 't ' 's ' S +1 16 #74 16 #73
S+ 2 NUL '1' S+ 2 16 #00 16 #31
6-831
 S1: The value in the file that the instruction reads is indicated by the value in S1.
Item Description
Refer to operand C for its file format. If the file format is 0, 1, 3, 5 or 7, the unit of
Value unit the value is a word. If the file format is 2, 4, or 6, the unit of the value is a double
word.
Parameter unit The parameter unit is a double word.
The value in S1 must indicate a value in the file.

Usage
If the value in S1 is 0, the instruction reads from the first value in the file.
 S3: The length of the data that the instruction reads from the file
The devices in which the instruction stores the data cannot exceed the device range. If the value in S3 is
larger than the number of values in the file, the length of the data read from the file is the number of
values in the file. The unit S3 is a double word.
 D: The initial device where the data is stored.
Flag Description
SM450 ON: the memory card is in the CPU module
The write protection switch on the memory card

_6 SM451 ON: the memory card is write protected.
The data is being written from the PLC to the memory card, or the data is being read from the
SM452
memory card into the PLC.
ON: an error occurs during the operation of the memory card. If the flag is ON, you must reset
SM453
it to OFF. The error code is stored in SR453.
6-832
4. If the format of the target file into which the instruction writes data is 0, the format of the file from which the
instruction reads data must also be 0. Otherwise, the instruction cannot read the data, and SM453 is ON. The
same applies to the other file formats.
Example
SM450 is ON when the memory card is inserted into the CPU module; SM452 is ON when the MREAD instruction
executes; SM452 is OFF when the MREAD instruction completes.
6_
The file from which the data is read
The file format:

D0 16#0011
The file name extension is .csv.
Use ASCII codes.
D300=16#6554
D302=16#0031
D10, D11 16#00000000 The values in the file starting from the first value are read.
D1 16#000A Ten values are read from every line.
D30, D31 16#00000020 The size of the data that is read from the file is 32 words.
D20 - The data that is read is stored in D20.
6-833
Additional remarks
4. If the value in D exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and the
_6
6-834
2302 MTWRIT P C, S, S1, S2, S3 Writing a string into the memory card

C    
S  
S1    
S2    
S3   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
C 
S 
S1 
S2 
S3 

AS AS -
Symbol
S ： Data source 6_
S1 ： Data length
S2 ： Separation mark
S3 ： File name
Explanation
1. This instruction writes a string into the memory card. The operands are described as follows.
Parameter
Description
value
If the file exists, the data that is written into the memory card is appended after the last byte
0
in the file.
(Appending)
If the file does not exist, it is created automatically.
If the file exists, the new data that is written to the memory card replaces the old data in the
6-835
1 file. The size of the file is the size of the new data.
(Overwriting) If the file does not exist, it is created automatically.
 S: The data source
If the string that the instruction writes into the file is “12345”, the instruction stores the characters in the
devices as follows. The basic unit is a byte, and so the instruction stores the first character in the low
byte in D300. The instruction stores the second character in the high byte in D300. The same applies to
other characters. The instruction stores “16#00” in the high byte in D300+2, and indicates the end of the
string.
S300 S300+1 S300+2

byte 2 byte 1 byte 4 byte 3 byte 6 byte 5
16#32 16#31 16#34 16#33 16#00 16#35
 S1: The length of the data that is written into the memory card
The basic unit is a byte. The devices where the instruction stores the data cannot exceed the device
range, and the length of the data that the instruction writes into the memory card cannot be more than
255 bytes.
 S2: The separation mark
If the value in S1 is N, the instruction writes the value in S2 into the memory card as follows.
_6 S2Operand
Description
High byte Low byte
16#00 or not
16#00 The N-byte data is written into the file.
16#00
The N+1-byte data is written into the file. The value in the high byte in S2 is the
Not 16#00 16#00
value in the N+1st byte.
The N+2-byte data is written into the file. The value in the high byte in S2 is the
Not 16#00 Not 16#00 value in the seventh byte, and the value in low byte in S2 is the value in the N+2th
byte.
name S3.
 S3–S3+4: S3 occupies five devices. The file name contains a maximum of nine characters,
including 16#00. If the string does not end with 16#00, an error occurs. When the instruction
reads the ending character, the instruction stops reading characters, and checks if the file name is
legal. The characters in the file name can be A–Z, a–z, and 0–9. The file name extension
depends on the file format. The file that the instruction creates is in the default folder. If the file
6-836
name is “Test1”, the instruction writes characters into the devices as follows.
ASCII
S 'e' ' T' S 16#6 5 16 #54
AS Code
CI I代碼
S +1 't ' 's ' S +1 16 #74 16 #73
S+ 2 NUL '1' S+ 2 16 #00 16 #31
2. Instruction flags
Flag Description
The write protection switch on the memory card
SM452
The data is being written from the PLC into the memory card, or the data is being read
6_
from the memory card into the PLC.
ON: an error occurs during the operation of the memory card. If the flag is ON, you must
SM453
reset it to OFF. The error code is stored in SR453.
16#0065 The file is a read-only file.
6-837
Example:
SM450 is ON when the memory card is inserted into the CPU module; SM452 is ON when the MTWRIT instruction
executes; SM452 is OFF when the MTWRIT instruction completes.
The file into which the data is written
The file format:
The unit of the character is a byte.

D0 16#0001
Use ASCII codes.
The data in D300 is written to the file.
D300 - The data that is written to the file
D10 16#000A The size of the string that is written to the file is 10 bytes.
_6
After the data is written to the file, the separation mark is appended after the last
D1 16#0A00
byte in the file.
D30=16#6554
D32=16#0031
Additional remarks
6-838
2303 MEMW P S, D, n Writing data into the file register

S     
D 
n   DWORD      
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 
D 
n 

AS AS -
Symbol
S ： The first address of the data source
D ： The first address where the data is stored
n ： Data length
6_
Explanation
1. This instruction writes data into the file register. The description of the operands is as follows.
• S: The initial address of the data source; it is suggested that you declare an array type variable.
• D: The initial address where the instruction stores data. It is suggested that you assign an address for the file
register and declare an array type variable.
• n: The length of the data that the instruction writes into the file register, between 1–2048. If the value
exceeds the range, the instruction is not executed, SM0 is ON, and the error code in SR0 is 16#200B.
• If the device S or D exceeds the allowed range, SM0 is ON, and the error code in SR0 is 16#2003.
2. Since it takes 60–120 ms for the instruction to write the data, it is suggested that you use this instruction when the
PLC is idle. For example, when there is no external interrupt task, no high-speed output, or any immediate events
for the PLC to process.
3. The instruction writes only when the contact switches from OFF to ON and writes only once.
NOTE: You can write into this file register a maximum of 100,000 times.
6-839
2304 MDEL P ctrl, fname Deleting files on the memory card

ctrl   
fname   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
ctrl  
fname 

AS AS -
Symbol
ctrl ： Control parameter
fname ： Data source
Explanation
1. This instruction writes data from the PLC to the memory card. The operands are described as follows.
_6  ctrl: The control parameter
0 The file name extension is .dmd.
File format 1, 2, 7 The file name extension is .cvs.
3, 4, 5, 6 The file name extension is .txt.
 You can use strings (less than 9 characters) in the in fname (file name).
 fname occupies five devices. The file name contains a maximum of nine characters, including 16#00. If the
string does not end with 16#00, an error occurs. When the instruction reads the ending character, it stops
6-840
reading, and checks if the file name is legal. The characters in the file name can be A–Z, a–z, and 0–9. The
file name extension depends on the file format. The file that the instruction creates is in the default folder. If
the file name is “Test1”, the instruction writes the characters into the devices as follows.
ASCII
S 'e' ' T' S 16#6 5 16 #54
AS Code
CI I代碼
S +1 't ' 's ' S +1 16 #74 16 #73
S+ 2 NUL '1' S+ 2 16 #00 16 #31
Flag Description
State of the write protection switch on the memory card

6_
The data is being written from the PLC to the memory card, or the data is being read
SM452
from the memory card to the PLC.
ON: an error occurs during the operation of the memory card. If the flag is ON, you
SM453
must reset it to OFF. The error code is stored in SR453.
6-841
Example
SM450 is ON when you insert the memory card into the CPU module; SM452 is ON when this instruction executes;
SM452 is OFF when this instruction completes.
D0 16#0001 The file name extension is .cvs.
D20=16#6554
D22=16#0031
Additional remarks
_6
1. If the value in ctrl exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and
2. If the value in fname exceeds the range, an operation error occurs, the instruction is not executed, SM0 is ON, and
6-842
6.24 Task Control Instructions

6.24.1 List of Task Control Instructions
The following table lists the Task Control instructions covered in this section.

API Function
2400 TKON –  Enabling a cyclic task
2401 TKOFF –  Disabling a cyclic task
6_
6-843
6.24.2 Explanation of Task Control Instructions
2400 TKON P S Enabling a cyclic task

S       
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

AS AS -
Symbol
S ： Task number
Explanation
1. This instruction enables the cyclic task specified by S.
2. When the PLC runs, the execution of the cyclic tasks depends on the setting of the cyclic tasks in ISPSoft.
_6
3. The operand S must be between 0-31.
4. Refer to the ISPSoft User Manual for more information about creating and enabling tasks.
Example
When the PLC runs, cyclic task (0) is enabled. When the TKON instruction in cyclic task (0) executes, it enables cyclic
task (1), and Y0.0 is ON.
You create cyclic tasks in ISPSoft, and you define their default enabled/disabled state in ISPSoft. Cyclic task (0) is
enabled when the PLC runs, and cyclic task (1) is not enabled when the PLC runs.
6-844
Cyclic task (1) is enabled by the TKON instruction in cyclic task (0).
Cyclic task (1) is executed.
Additional remarks
Refer to the ISPSoft User Manual for more information on tasks.
6_
6-845
2401 TKOFF P S Disabling a cyclic task
Device
S   DWORD     
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S  

AS AS -
Symbol
S ： Task number
Explanation
1. This instruction disables the cyclic task specified by S.
2. When the PLC runs, the execution of the cyclic tasks depends on the setting of the cyclic tasks in ISPSoft.
3. The operand S must be between 0-31.

_6
4. Refer to the ISPSoft User Manual for more information about creating and enabling tasks.
Example
When the PLC runs, cyclic task (0) and cyclic task (1) are enabled. When the TKOFF instruction in cyclic task (0)
executes, it disables cyclic task (1), and Y0.0 is OFF.
You create cyclic tasks in ISPSoft and you define their default enabled/disabled state in ISPSoft. Cyclic task (0) and
cyclic task (1) are enabled when the PLC runs, and cyclic task (1) is disabled when the TKOFF instruction in cyclic task
(0) executes. Cyclic task (1) is disabled by the execution of the TKOFF instruction in cyclic task (0).
6-846
Cyclic task (1) is not executed.
Additional remarks
Refer to the ISPSoft User Manual for more information on tasks.
6_
6-847
6.25 SFC Instructions

6.25.1 List of SFC Instructions
The following table lists the SFC (Sequential Function chart) instructions covered in this section.

API Function
2500 SFCRUN – – SFC Run
2501 SFCPSE – – SFC Pause
2502 SFCSTP – – SFC Stop
_6
6-848
6.25.2 Explanation of Task Control Instructions
2500 SFCRUN S1, S2, S3 SFC Run

S1
S2   
S3
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1
S2  
S3

- AS －
Symbol
S1 ： Name of the SFC POU
6_
Explanation
1. This instruction runs the SFC (Sequential Function Chart) program specified by S1 according to the function code
in S2.
2. The instruction runs the SFC POU (Program Organization Unit) specified by S1 only when the PLC is scanning the
SFC POU.
3. The operands are described as follows.
 S1 defines the name of the SFC POU.
 When the designated SFC POU of S1 executes, the instruction clears the parameters (such as
SFC/STEP/ACTION/TRANSITION) for the SFC program when S2=0 or 1, and the SFC execution starts
according to the value specified in S2.
 IF S2=0, the system executes the SFC POU from the initial step.
 IF S2=1, the system executes the SFC POU from the designated step in S3.
6-849
 If S2=2, the instruction does NOT clear the status and the parameters (such as
SFC/STEP/ACTION/TRANSITION) for the SFC and the system starts executing from where it paused.
 S3 designates where to start (which step) in the SFC program in S1.
4. The range of S2 is between 0–2. If it is out of range, it is evaluated as 0.
5. When the state of the SFC POU is RUN, executing this instruction is invalid.
Example
Set up one LD (ladder) POU and specify its POU name as “Main”, and then set up two SFC POUs with the names of
“TestSFC1” and “TestSFC2”.
1. When the PLC executes the Main program (RUN), TestSFC1 and TestSFC2 execute the SFCSTP instruction (API
2502), and the two SFC POUs stop executing.
2. When M0 switches from OFF to ON, TestSFC1/ TestSFC2 POU execute the SFCRUN* instruction. See below for
the contents of the TestSFC1 and TestSFC2 for execution details. When S2=0, the SFC status and parameters are
cleared and begin to execute from STEP 1. When S2=1, the SFC status and parameters are cleared and begin to
execute from the designated STEP in S3.
3. When M1 switches from OFF to ON, TestSFC1 POU pauses. When S2=1, all the SFC executing actions and outputs
_6 are cleared, and the system runs the final scan.
4. When M2 switches from OFF to ON, TestSFC1 POU executes. When S2=1, the SFT status and parameters are
cleared, and the system begins to execute from STEP 2.
5. When M3 switches from OFF to ON, TestSFC2 POU pauses. When S2=0, all the SFC executing actions and outputs
are kept, and the system does not run the final scan.
6. When M4 switches from OFF to ON, TestSFC1 POU executes. When S2=2, the SFC status and parameters are
and the SFC begins to execute from where it paused.
*SFCRUN activates the SPC POU at the next scan.
6-850
Main POU
6_
6-851
TestSFC1 POU
_6 TestSFC2 POU
Additional remarks
Refer to the ISPSoft User Manual for more information on Sequential Function Charts.
6-852
2501 SFCPSE S1，S2 SFC Pause

S1
S2   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1
S2  

- AS －
Symbol
S1 ： Name of the SFC POU
Explanation
1. This instruction pauses the SFC POU specified by S1 according to the function code in S2.
6_
2. The instruction can pause the SFC POU specified by S1 only when the PLC is scanning the SFC POU.
3. When paused, the SFC status and parameters (such as SFC/STEP/ACTION/TRANSITION) are stored.
4. The operands are described as follows.
 S1 defines the name of the SFC POU.
 When S2=0, the instruction preserves all the executing actions of the SFC and the outputs, and the system
does not run the final scan.
 When S2=1, the instruction clears all the executing actions and the outputs of the SFC POU, and the system
runs the final scan..
5. The range of S2 is 0–1. When it is out of range, it is processed as 0.
6. When the state of the SFC POU is PAUSE/STOP, executing this instruction is invalid.
6-853
Example
Refer to the SFCRUN (API 2500) programming example for more information.
Additional remarks
Refer to the ISPSoft User Manual for more information on SFCs.
_6
6-854
2502 SFCSTP S SFC Stop

S
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1

- AS －
Symbol
S ： Name of the SFC POU
Explanation
1. This instruction stops the SFC POU specified by S.
2. This instruction stops the SFC POU specified by S1 only when the PLC is scanning the SFC POU.
6_
3. When stopping, the instruction clears the SFC status and parameters, and the system runs the final scan.
4. When the state of the SFC POU is STOP, executing this instruction is invalid.
Example
Refer to the SFCRUN (API 2500) programming example for more information.
Additional remarks
Refer to the ISPSoft User Manual for more information on SFCs.
6-855
6.26 High-speed Output Instructions

6.26.1 List of High-speed Output Instructions
The following table lists the High-speed Output instructions covered in this section.
Instruction Pulse
numbered
numbered
code instruct
Even-
axis*1
axis*2
Odd-
API Function
ion
16-bit 32-bit
2700 – DPLSY – High-speed pulse output (without ramp-up/down process) V V
2701 – DPLSR – High-speed pulse output (with ramp-up/down process) V V
2702 PWM DPWM – Pulse width modulation V V
2703 JOG DJOG – JOG output V V
2704 – DZRN – Zero return V –
2705 – DPLSV – Adjustable pulse output V V
2706 – DDRVI – Relative position control V V
2707 – DDRVA – Absolute position control V V
2708 CSFO – – Catch speed and proportional output V –
2709 – DDRVM – Mark alignment positioning V –

_6
2710 – DPPMR – 2-Axis relative-coordinate point-to-point synchronized motion V –
2711 – DPPMA – 2-Axis absolute-coordinate point-to-point synchronized motion V –
2712 – DCICR – 2-Axis relative-position clockwise arc interpolation V –
2713 – DCICA – 2-Axis absolute-position clockwise arc interpolation V –
2714 – DCICCR – 2-Axis relative-position counterclockwise arc interpolation V –
2715 – DCICCA – 2-Axis absolute-position counterclockwise arc interpolation V –
2716 – DCCMR – Relative-position circle drawing V –
2717 – DCCMA – Absolute-position circle drawing V –
2718 TPO – – Position planning table controls the output V –
 Setting single-axis output parameters in the position planning

2719 – DTPWS V –
table
–  Setting linear interpolation parameters in the position planning

2720 DTPWL V –
table
6-856
Instruction Pulse
numbered
numbered
code instruct
Even-
axis*1
axis*2
Odd-
API Function
ion
16-bit 32-bit
 Setting arc interpolation parameters in the position planning

2721 – DTPWC V –
table
2723 – DPPGB – Point to point go back and forth V –
2724 – DZRN2 – Zero return 2 (directional output can be defined) V V
NOTE:
*1: Even-numbered axes include Y0.0, Y0.2, Y0.4, Y0.6, Y0.8, and Y0.10.
*2: Odd-numbered axes include Y0.1, Y0.3, Y0.5, Y0.7, Y0.9, and Y0.11.
6_
6-857
6.26.2 Explanation of High-speed Output Instructions
High-speed pulse output (without

2700 D PLSY S1，S2，D
ramp-up/down process)

S1      
S2      
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
S1  
S2  
D 

－－ AS
Symbol
S1 : Pulse output frequency
S2 : Number of pulses to output
D : Pulse output device

_6
Explanation
1. This instruction specifies the pulse output (S1, S2) for the device specified in D with no ramp up or ramp down when
the frequency changes. S1 specifies the pulse output frequency range: for line driver output models, the range is
between 0–4MHz; for open collector output models, the range is between 0 Hz–200 kHz. The unit of the output
frequency is 1 Hz. The error rate for 200 kHz is about 0.02% and for 100 kHz it is about 0.01%. The error rate
decreases with decreasing frequency. For example, if the output frequency setting is 199990 Hz, the actual output is
199960 Hz. If the output frequency setting is 99999 Hz, the actual output is 99990 Hz. If the output frequency is out
of the valid range, the PLC automatically processes it as the maximum or minimum pulse output frequency.
2. You can change the output frequency specified by S1 during the execution of the instruction without using the ramp
up/down process. The time to change the frequency is when the PLC is scanning the instruction and the instruction
has completed output of a full pulse.
3. S2 specified the number of output pulses. The range is between 0–2,147,483,647. When you set the number of output
pulses to 0, then the number of pulses is not restricted and pulses are output constantly until the instruction is disabled.
When the number of output pulses is set to less than 0, no pulses are output.
4. After the instruction starts to output pulses, the number of output pulses specified by S2 cannot be changed.
6-858
5. D only allows Y0.0–Y0.11 as the output devices. After the instruction is executed, its output function becomes the
high-speed output, and the basic instruction output point control is invalid. It is suggested that you do not use the
general output function after using the high-speed output function in the program.
6. The ratio of Duty-OFF Time and Duty-ON Time for the pulse output is 1:1.
7. There is no limit to how many times you can use the instruction a program. But only one output instruction that uses
the same output point can be executed in the same scan cycle. When several high-speed pulse output instructions
start the same output point in the program, the PLC first performs the output based on the instruction that is executed
first.
8. After every high-speed output instruction for every output point is executed, other instruction occupying the same
output point can not start until the high-speed output instruction in execution is disabled.
9. When the high-speed output instruction is executed in an interrupt program or is not in the main process, it is
suggested that you use the instruction with the auto-reset function when output is completed and the PLC updates
the output state in the END instruction.
10. After the stop flag is set, the PLC stops the output and clears the busy flag only after executing the start instruction a
second time and outputting a full pulse. The PLC continues to output pulses when the stop flag is reset and the
previously stopped pulse output is not finished. You set and reset the stop flag is set in the program.
11. The high-speed output points and corresponding SM/SR are listed in the following table.
Output point number Attribute#2 Y0.0 Y0.1 Y0.2 Y0.3 Y0.4 Y0.5 6_
Busy flag R SM460 SM472 SM480 SM492 SM500 SM512
Completion flag#3 R/W SM461 SM473 SM481 SM493 SM501 SM513
Stop flag R/W SM463 SM474 SM483 SM494 SM503 SM514
Output completion
R/W SM470 SM475 SM490 SM495 SM510 SM515
auto-reset#4
Present output
SR460 SR474 SR480 SR494 SR500 SR514
position#1 R/W
SR461 SR475 SR481 SR495 SR501 SR515
（32-bit）
Output point number Attribute #2 Y0.6 Y0.7 Y0.8 Y0.9 Y0.10 Y0.11
Busy flag R SM520 SM532 SM540 SM552 SM560 SM572
Completion flag #3 R/W SM521 SM533 SM541 SM553 SM561 SM573
Stop flag R/W SM523 SM534 SM543 SM554 SM563 SM574
6-859
Output point number Attribute#2 Y0.0 Y0.1 Y0.2 Y0.3 Y0.4 Y0.5
Output completion
R/W SM530 SM535 SM550 SM555 SM570 SM575
auto-reset #4
Present output position

SR520 SR534 SR540 SR554 SR560 SR574
#1
R/W
SR521 SR535 SR541 SR555 SR561 SR575
（32-bit）
Notes:
#1: All present output positions are latched when power is off.
#2: R means Read-only registers, and the data in the registers cannot be modified. R/W means the data in the
registers can be read and written.
#3: It is suggested that you clear the completion flag. If the completion flag is not cleared, it is cleared automatically
when the high-speed output instruction is executed the next time.
#4: You set the output completion auto-reset flag. The PLC clears the flag automatically after the output is
completed.
Example 1
_6 1. When X0.0 is ON, Y0.0 outputs 200 pulses at 1kHz. SM461 is ON when the pulse output is completed and then
Y0.12 is ON.
2. When X0.0 is OFF, Y0.0 stops the output. It restarts the pulse output when X0.0 switches to ON again.
0.5ms
輸出 Y0 2 3 200
Output point Y0.0
1ms
6-860
Example 2
External interrupt input X0.0
External interrupt input X0.1
6_
Explanation
1. Y0.0 outputs 1000 pulses when X0.0 receives one external interrupt signal. Y0.2 outputs 1000 pulses when
X0.1 receives one external interrupt signal.
2. When the external interrupt input X triggers the pulse output from Y, the interval time between the Y pulse
output completion and the next external interrupt input X trigger must be one or more PLC scan cycles.
6-861
Example 3 (ST program)
Explanation
1. When M0 is ON, Y0.0 outputs 1000 pulses at 1kHz. When M1 is ON, it indicates Y0.0 is used for high-speed pulse
output.
2. When the pulse output is completed, SM461 is ON. And if M1 is also ON, it triggers SM470 (output completion
auto-reset for Y0.0) to be ON and Y0.0 is free and ready to be used again.
3. When M0 switches from OFF to ON, the pulse output is restarted.
4. When there are more than two high-speed output instructions in a program, do not use the variable name, M1,
repeatedly.
5. It is suggested not to use ST language in a program if there is any chance the outputting needed to be stopped.
_6
6-862
High-speed pulse output

2701 D PLSR S1，S2，S3，D
(with ramp-up/down process)

S1      
S2      
S3      
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
D 

－－ AS
Symbol
S1 ： Target output frequency
S2 ： Number of output pulses
S3 ： Ramp-up/ down time

6_
D ： Pulse output device
Explanation
1. This instruction specifies the pulse output (S1, S2) for the device specified in D with ramp up or ramp down in the
frequency change. S1 specifies the pulse output frequency as 4 MHz for line driver output models and the pulse
output frequency between 0 Hz–200 kHz for the open collector output models. The unit of the output frequency is 1
Hz. The tolerable error rate for 200 kHz is about 0.02% and for 100 kHz it is about 0.01%. The error rate decreases
with decreasing frequency. For example, if the output frequency setting is 199990 Hz, the actual output is 199960
Hz. If the output frequency setting is 99999 Hz, the actual output is 99990 Hz. If the output frequency is out of the
valid range, the PLC automatically processes it as the maximum or minimum pulse output frequency.
2. After the instruction is executed, you can change the target output frequency specified by S1 and the PLC performs
the ramp up or ramp down process according to the ramp up or ramp down time setting S3. The time to change the
frequency is when the PLC is scanning the instruction and the instruction has completed output of a full pulse.
3. S2 is the number of output pulses. The range is between 0–2,147,483,647. When you set the number of pulses to 0,
then the number of pulses is not restricted and pulses are output continuously until the instruction is disabled.
6-863
4. After the instruction starts to output pulses, the number of output pulses that S2 specifies cannot be changed.
5. S3 sets the ramp-up or ramp down time with the unit of 1ms. The value is effective when the instruction is executed
for the first time. If the target frequency specified by S1 is modified in the ramp-up process, the ramp up or ramp down
time is reloaded for execution. But if the target frequency is modified when the output enters the ramp-down process,
the instruction ignores the change.
6. D only allows Y0.0–Y0.11 as the pulse output devices. After the instruction is executed, its output function becomes
the high-speed output, and the general instruction output point control is invalid. It is suggested that you do not use
the general output function after using the high-speed output function in the program.
7. The target output frequency S1, number of output pulses S2 and ramp up/down time S3 are illustrated in the following
graphic.
_6 8. The ratio of Duty-OFF Time and Duty-ON Time for the pulse output is 1:1.
first.
10. After the high-speed output instruction for one output point is enabled, other instructions that occupy the same output
point can not start until the high-speed output instruction in execution is disabled.
11. When the high-speed output instruction is executed in an interrupt program or is not in the main program, it is
suggested that you use the instruction with the auto-reset function when the output is completed and the PLC updates
the output state in the END instruction.
12. After the stop flag is set, PLC performs the ramp-down stop; or it immediately stops the output only after the start
instruction is executed a second time and outputs a full pulse.
13. Refer to the PLSY instruction (API 2700) for an explanation of the high-speed output points and corresponding SM/SR.
14. Refer to Example 3 from the PLSY instruction (API 2700) for programming in ST language.
6-864
15. When the target output frequency is reached, you can change the set target output frequency. The frequencies for
ramp up and ramp down are already set, if you change the set target output frequency during the instruction execution,
the frequency goes either ramping up or ramping down. If more than one target output frequencies are set, it is
suggested to set the last new target frequency the same as the original target frequency to avoid abrupt change when
it needs to come to a stop.
See the example below. The blue line indicates the original target freueency and the red line indicates new target
frequency.
 Situation A: ramping up
Freq. 
 
Time

 
 Number of output pulses

 Ramp up time 6_
 The first target frequency
 Position to change to the new target frequency
 New target frequency
6-865
 Situation B: ramping down
Freq.
  
Time


 


 Ramp up time
 Position to change to the new target frequency
 New target frequency
 Ramp down time
 Suggested design: it is suggested to set the last new target frequency the same as the original target frequency
to avoid abrupt change when it needs to come to a stop.
_6
 
Freq.
 

Time

    

 Ramp up time
 Position to change to the first new target frequency
 Position to change to the second new target frequency
 Ramp down time
 Position to change to the third new target frequency
 Position to change to the original set targe frequency and then start ramping down to stop.
6-866
2702 D PWM S1，S2，D Pulse width modulation

S1          
S2          
D  DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1    
S2    
D 

－ AS AS
Symbol
S1 ： Pulse output width
S2 ： Pulse output cycle

6_
Explanation
1. This instruction specifies the pulse output width. The 16-bit instruction uses 100 us as the output unit, while the 32-
bit instruction uses 1 us as the output unit.
Output instruction PWM DPWM
Range of pulse output width S1 0–30000 0–60000
Range of pulse output cycle S2 0–30000 0–60000
2. S1 (pulse output width--Duty ON) is defined as t, S2 (pulse output cycle time--Cycle time) is T as shown below. It is
recommended that S1≦S2.
6-867
3. D only allows Y0.0–Y0.11 as the pulse output device.
first.
5. If S1≦0 or S2≦0, it is processed as 0 (the pulse output is OFF). If S1＞S2, it is processed as S1＝S2. When S1＝S2
and S2 is not 0, the pulse output is always ON.
6. You can modify the pulse output width S1 and pulse output cycle S2 when the PWM instruction is executed.
7. The relevant special registers SR are listed in the following table.
Output point number Attribute Y0.0 Y0.1 Y0.2 Y0.3 Y0.4 Y0.5
Present output
SR460 SR474 SR480 SR494 SR500 SR514
position#1 R/W
SR461 SR475 SR481 SR495 SR501 SR515
（32-bit）
Output point number Attribute Y0.6 Y0.7 Y0.8 Y0.9 Y0.10 Y0.11

SR520 SR534 SR540 SR554 SR560 SR574
#1
R/W
SR521 SR535 SR541 SR555 SR561 SR575
（32-bit）
_6 #1：All present output positions are latched when power is off.
8. Refer to Example 3 from the DJOG instruction (API 2703) for programming in ST language.
Example
When X0.0 is ON, Y0.1 outputs the following pulses. When X0.0 switches to OFF, Y0.1 output changes to OFF.
t=1000ms
Output Y0.1
Output Y1
T=2000ms
6-868
2703 D JOG S1，S2，S3，D1，D2 JOG output

S1        
S2        
S3        
D1 
D2  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1    
S2    
S3    
D1 
D2 

－ AS AS
Symbol
S1 ： Ramp-up time
6_
S3 ： Ramp-down time
D1 ： Pulse output device
D2 ： Auxiliary output device
Explanation
1. This instruction specifies the JOG output (S1 , S2 , S3) for the devices specified in D1 and D2. S1 is the ramp-up time
with the unit of 10 ms. For Example , the value 10 means the ramp-up time is 100 ms. After the instruction is
executed, the output frequency can be divided by ten, and it speeds up once every 10ms. It reaches the JOG
target frequency specified by S2 at the ramp-up time S1.
2. When the instruction is disabled, its output frequency ramps down once every 10ms based on the ramp-down time
in S3. The output does not stop until reaching the ramp-down time. If you set the ramp-down time to 0, the output
stops immediately.
6-869
3. The range of the ramp-up time S1 and the ramp-down time S3 is between 0–3000 (0–30 seconds). If the setting
value is out of range, the PLC processes it as the minimum or maximum output value. The ramp-up time and
ramp-down time are affected by the scan time. If you require accurate ramp-up or ramp-down time, it is
recommended that you use an output instruction with specified ramp up or ramp down time such as the DDRVI
4. The range of the target output frequency S2 is between -200 kHz to 200 kHz. If the setting value is out of the range,
the PLC processes it as the minimum or maximum output value. A positive number for the output frequency
indicates forward output. A negative number for the output frequency indicates reverse output.
5. D1 allows only Y0.0–Y0.11 for the output point. For the auxiliary output point specified by D2, refer to the output
points in the following table. If you choose other output points or the M device, the value in SR indicating the output
mode is invalid and the Pulse+direction mode is valid by default. D2 is a direction output point.
D1 selects the even output point number.
Output point for D1 Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
Direction output point

Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
for D2
Busy flag SM460 SM480 SM500 SM520 SM540 SM560
Output mode SR462 SR482 SR502 SR522 SR542 SR562
_6 Present output SR460 SR480 SR500 SR520 SR540 SR560
position SR461 SR481 SR501 SR521 SR541 SR561
D1 selects the odd output point number.
Direction output point

Y1.0 or above or any M device (BOOL)
for D2
Present output SR474 SR494 SR514 SR534 SR554 SR574
6. When the value is 0 in SR462, SR482, SR502, SR522, SR542, and SR562, it indicates the Pulse+direction output
mode. When the value is 1 in SR462, SR482, SR502, SR522, SR542, and SR562, it indicates the A/B phase
output mode.
Note: you can select the output mode only when D1 uses an even output point and D2 uses a recommended
direction output point.
6-870
7. When the direction outputs are not using the default outputs to output, you can refer to the table below for setting
up the outputting time that pulse outputting goes first before direction outputting does. So that you can be sure the
outputting only happens when switching to the direction outputs. The unit for SR is millisecond and the range is 0-
20 ms. Default is 0, indicating inactive.
SR number SR640 SR641 SR642 SR643 SR644 SR645
Note: the time source here is from PLC scan time. (available for firmware version 1.02.20 or later)
8. When the output begins, the Busy flag SM is ON. When the output is completed, the Busy flag is automatically
reset to OFF and the Completion flag is not ON.
9. The following graph shows the output timing diagram. For the Busy flag in the following graph, refer to the Busy
flag axis.
Jog_in
Busy flag
S2 > 0 6_
S1 S3
D1
0 Time
S1 S3
S2 < 0
10. You can modify the target output frequency during instruction execution. When the new frequency is greater than
the previous one, the instruction uses the ramp-up slope. When the new frequency is less than the previous one,
the instruction uses the ramp-down slope.
11. The instruction sets the ramp-up/down slope through conversion of the set time and target frequency when the
instruction is executed. The slope does not change with the changing target frequency in the output process. For
example, the original target output frequency is 1 kHz and then it is modified to 2 kHz. The actual ramp-down time
is different from the original time. The dotted line is the ramp-up and ramp down timing diagram after the target
frequency is modified.
6-871
Jog_in
Change S2
S2
D1
Time
S1 S3
Example (ST program):
It is suggested to use ladder diagrams as the programming language in this instruction. If you need to use structured
texts, you need to use the output completion auto-reset flag as well for the PLC to know the output point is free and
ready to be used again when the output completes. Taking Y0.0 as the output point, the program should be written as
below. See the following example.
_6
6-872
2704 D ZRN S1，S2，S3，S4，D Zero return

S1      
S2      
S3      
S4 
D 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4 
D 

－－ AS
Symbol
S1 ： Target frequency for zero return

6_
S2 ： JOG frequency for DOG
S3 ： Zero return mode
S4 ： Input device for DOG
Explanation
1. This instruction causes the machine to return to the zero point. The range of the target frequency for zero return S1
is between 1 Hz–200 kHz. The JOG frequency S2 should be less than the target frequency S1. The JOG frequency
S2 is the start frequency. If S1 is less than S2, S1 is automatically revised processed as equal to S2.
2. The input point for S4 and output point for D must match. Do not change them during instruction execution. The
input point for S4 is suggested to use the 16 high-speed input points X0.0–X0.15. They will not be affected by PLC
instruction scan time. If you use X1.0 successive input points or M devices (firmware V1.02.10 or above is
required), they will be affected by the PLC instruction scan time. Refer to the following table for the selection of D
output point and direction output point. If D is not the preset Pulse+direction output (default: 0), change the mode
to A/B phase output by setting SR to 1.
6-873
Axis number Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6

Can be any one of the input points X0.0–X0.15. But the same input point cannot be
Input point for S4 selected for different axis output. If the DOG point shakes or the switch bounces, set
the input point filter time in HWCONFIG.
Output point for D Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
Direction output point Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
Completion flag SM461 SM481 SM501 SM521 SM541 SM561
SR460 SR480 SR500 SR520 SR540 SR560
SR461 SR481 SR501 SR521 SR541 SR561
3. Use S3 to select the zero return mode. The function code is set by the two high and low16-bit parameters. See the
following table for details.
S3: select the zero return mode

High 16-bit Low 16-bit
b31~b16 b15~b6 b5 b4 b3~b0
Number of pulses for motion Direction setting*1 Setting DOG signal

Mode settig
reserved 0: in the negative direction 0: contact A
Number of Z phases 0~15 (F)
1: in the positive direction 1: contact B
Note 1: This function is only available for firmware version 1.04.30 or later. See the diagram below for
mode setting.
Execute DZRN DOG signal received Move away frm DOG signal
_6
0: stops immediately
2: moves a number of pulses and then stops
Moves in the
3: searches for a number of Z phases and then stop
negative 4: outputs the clear signal
Searches for
direction 6: moves a number of pulses and outputs the
the zero point clear signal
in the 7: searches for a number of Z phases and outputs
the clear signal
direction of
Moves in the
negative or
positive direction
positive 1, 8, 9: stops immediately
10: moves a number of pulses and then stops
11: searches for a number of Z phases and then stop
5, 12, 13: outputs the clear signal
14: moves a number of pulses and outputs the clear
signal
15: searches for a number of Z phases and outputs
the clear signal
6-874
4. Use S3 to select the zero return mode. The function code is set by the two high and low16-bit parameters. See the
following table for details.
Code
Functions High 16- Low Explanation
bit 16-bit
When the instruction is executed, the search for
the zero point is in the negative direction with the
Leaves the zero point in target frequency. When the zero point is ON (the
the negative direction and zero point signal changes from OFF to ON), the
0 0
then stops frequency is decreased to the JOG speed and
(Mode 0) the motion in the negative direction continues,
and does not stop until the zero point signal
changes from ON to OFF.
the positive direction and zero point signal changes from OFF to ON), the
0 1
then stops frequency decreases to 0 immediately, and then
(Mode 1) the motion is in the positive direction at the JOG
speed, and does not stop until the zero point
signal changes from ON to OFF.
Returning to the zero point is the same as that
for the low 16-bit code. After the zero point is
Number ON, the motion continues according to the
Mode 0 Moves again after
of pulses 2 number of specified pulses. When the high 16-
returning to the zero point
for motion bit code is a positive number, the search is in
the positive direction. A negative value means
that the search is in the negative direction. 6_
Returning to the zero point is the same as that
for the low 16-bit code. After returning to the
zero point, the motion continues according to
the number of Z phases. When the high 16-bit
Mode 0 Searches Z phase
code is a positive number, the search is in the
after returning to the zero Number
positive direction. A negative value indicates
point of Z 3
that the search is in the negative direction.
(Z phase input point is set phases
Suppose you specified that the rising-edge
in HWCONFIG )
trigger of X0.1 as the condition for the Z phase
input in HWCONFIG. The counting is
performed once whenever the rising-edge
trigger for X0.1 occurs.
Choosing a value between 4–7 means
4+0=4 selecting the functions codes 0–3 respectively,
Number
Mode 0 Outputs the clear and the specified output point sends an ON
of pulses 4+1=5
signal after returning to the signal that is about 20ms wide when the
for motion 4+2=6
zero point. function execution completes. The range of the
or 4+3=7
(Output clear point is set in output point is Y0.12–Y0.15 and Y1.0–Y1.15.
number of (bit
HWCONFIG ) For example, if you specify Y1.12 as the output
Z phases 2=ON) point in HWCONFIG, it indicates Y1.12 is for
the output of clear signals.
Leaves the zero point in
8+0=8 The operation for zero point return is the same
the positive direction and 0
8+1=9 as that for code 1 (mode 1).
then stops
6-875
(Mode 1) (bit
3=ON)
The operation for zero point return is the same
as that for low 16-bit code 1.
8+2=10 After returning to the zero point, the motion

Mode 1 outputs the Number
continues in accordance with the number of
number of pulses after of pulses (bit
specified pulses. When the value of the high 16-
returning to the zero point for motion 3=ON)
bit code is a positive number, the motion is in the
positive direction. A negative number indicates
that the motion is in the negative direction.
The operation for zero point return is the same
as that for low 16-bit code 1.
After returning to the zero point, the motion
Mode 1 Searches for Z continues in accordance with the number of Z
phase after returning to the Number 8+3=11 phases to seek. When the value of the high 16-
zero point of Z (bit bit code is a positive number, the motion is in the
(Z phase input point is set phases 3=ON) positive direction. A negative number indicates
in HWCONFIG ) that the motion is in the negative direction.
If the rising edge trigger for X0.1 is the condition
for Z phase input, counting is performed once
when the rising-edge trigger for X0.1 occurs.
Mode 1 Outputs the clear 0 or 12–15
signal after returning to the number of
(bit 3=bit After returning to the zero point in mode 1, the
zero point pulses or
2 20ms-width clear signal is output.
(Output clear point is set in number of
Z phases =ON)
HWCONFIG )
When in the low 16-bit code, bit 4 is ON, it
+16
means the zero point is ON as the DOG point
DOG point is B point (bit
changes from ON to OFF and the zero point is
_6 4=ON)
left as the DOG point changes from OFF to ON.
5. The execution sequence is based on the value of the low 16-bit code in the table above, and described below.
The direction of DOG signal is determined by the value of bit 5.
 The DOG signal is determined by the value of bit 4.
 Mode 0 or mode 1 for the zero point return, selected according to the value of bit 3.
 The operation of the zero point return is performed according to the values of bit 1 and bit 0.
 The operation of the clear signal specified by bit 2 is performed.
6. Set the input point and the rising edge trigger condition in HWCONFIG, when the position control system needs
positive and negative limit input points. Note that the limit input points must not be the same as the zero point or Z
phase input points.
7. The Completion flag is set to ON after the instruction finishes performing the specified function. For example, for
function code 6, the PLC sets the Completion flag to ON only when the Z phase seeking completes.
8. After the DZRN instruction is executed, an interrupt service program is not executed till the DZRN instruction is
disabled, if the specified input point for the zero point is the same as that for the external input interrupt in the
program.
6-876
9. When the limit switch is specified in HWCONFIG, and there is an external input interrupt service program, the
interrupt program will be executed at the same time.
only once.
The steps for performing the functions are as below
Function code 0:
 The DZRN function is executed and the search for the zero point is in the negative direction with the target
frequency.
 After the DOG signal is received, the output frequency decreases to the JOG frequency. The output continues in
the negative direction and does not stop until the zero point signal changes from ON to OFF.
 The output stops when the signal changes from ON to OFF and the axis moves away from the DOG signal.
Negative direction
Completion flag ON
DOG signal ON
Frequen cy
Target frequency
JOG frequency 6_
Time
1 2 3
Function code 1:
frequency.
 After the DOG signal is received, the output is in the positive direction with the JOG frequency after the output
frequency decreases, and the motion direction reverses. The output does not stop until the zero point signal
changes from ON to OFF.
 The axis moves away from the DOG signal and PLC stops when the signal changes from ON to OFF.
6-877
P ositive
Negative direction direction
Completion flag ON
DOG signal ON
F requency
Target frequency
JOG frequency
Time
1 2 3 4
Function code 2:
frequency.
 After the DOG signal is received, the output decreases the frequency to the JOG frequency and continues in the
negative direction.
 When the DOG signal is left and the signal changes from ON to OFF, the specified number of pulses are output.
 The first pulse output starts.
 When the 100th pulse output completes, the PLC stops and the Completion flag is ON.
_6
Completion flag ON
DOG signal ON
Output Y
Frequency
Target frequency
JOG frequency
Time
1 2 3 4 5
6-878
Function code 3:
 DZRN function is executed and the search for the zero point is in the negative direction with the target
frequency.
 After the DOG signal is received, the output frequency decreases to the JOG frequency and the motion
continues in the negative direction.
 The motion goes on according to the number of Z phases when the signal changes from ON to OFF after the
axis moves away from the DOG signal.
 The first Z phase pulse
 The motion stops after the 2nd Z phase completes and the Completion flag is ON.
Completion flag ON
DOG signal ON
Z phase pulse
Frequency
Target frequency
JOG frequency
Time
1 2 3 4 5
6_
Function code 4:
frequency.
 After the DOG signal is received, the output frequency decreases to the JOG frequency and continues in the
negative direction. The output does not stop until the zero point signal changes from ON to OFF.
 After the axis moves away from the DOG signal, the output stops when the signal changes from ON to OFF and
the clear signal is be ON for about 20 milliseconds.
6-879
Negative direction
Completion flag ON
Clear signal ON
DOG signal ON
Frequency
Target frequency
JOG frequency
Time
1 2 3
Function code 0+ the negative limit function enabling:
You set the negative limit input point in HWCONFIG, and then download the setting to the PLC. The PLC
automatically calculates the negative limit function when the instruction is executed.
frequency.
 After the negative limit switch is ON, the motion stops and then goes in the positive direction after reversing
direction.
 The motion continues in the positive direction after leaving the negative limit switch.
 The output frequency ramps down after receiving the DOG signal. The reverse output is performed with the
_6
JOG frequency after reversing direction.
 The output stops when the signal changes from ON to OFF after the axis moves away from the DOG signal.
Positive Negative
Negative direction direction direction
Completion flag ON
DOG signal
Negative limit switch ON
Frequency
Target frequency
JOG frequency
Time
1 2 3 4 5
6-880
Example 1
When M0 is ON, outputting the pulse from Y0.0 with a frequency of 20 kHz to search for the zero point in the negative
direction. When the DOG signal is received and X0.4 is ON, it keeps moving in the negative directon with the JOG
frequency of 1 kHz. The output stops immediately after X0.4 changes from ON to OFF.
Explanation
S3 is set to 0.
High 16-bit [0000] is to disable the function to move a number of pulses or to search for Z phases.
Low 16-bit [0000] is Mode 0; when the DOG signal is received, the axis moves in the negative direction; after the axis
moves away from the DOG signal, it stops immediately.
Example 2
6_
direction. When the DOG signal is received and X0.4 is ON, the PLC decreases the frequency to the JOG frequency of 1
kHz and keeps moving in the positive directon with the JOG frequency of 1 kHz. When X0.4 is OFF, the PLC starts to
seek the Z phase pulse in the positive direction. When X0.5 receives two pulses, the PLC stops and Y1.4 outputs a
20ms-width pulse.
6-881
Explanation
1. If you specify the rising-edge trigger at X0.5 as the condition for Z phase input in HWCONFIG, the count is
incremented once whenever the rising-edge trigger at X0.5 occurs.
2. Y1.4 is specified as the output point for outputting the clear signal in HWCONFIG.
3. S3 is set as 16#FE0C000E.
High 16-bit [0002] is to search for the Z phase twice, once the axis moves away from the DOG signal.
Low 16-bit [0007] is Mode 7; when the DOG signal is received, the axis moves in the negative direction; after the
axis moves away from the DOG signal, and found the Z phase, a clear signal is outputted (20ms).
Example 3
direction. When the DOG signal is received and X0.4 is ON, the PLC decreases the frequency to the JOG frequency of 1
kHz and keeps moving in the positive directon with the JOG frequency of 1 kHz. When X0.4 is OFF, the axis starts to
move after 500 pluse output completes in the negative direction. Y1.4 outputs a 20ms-width pulse and then stops
outputting.
_6
Explanation
1. Y1.4 is specified as the output point for outputting the clear signal in HWCONFIG.
2. S3 is set as 16#FE0C000E.
High 16-bit [FE0C=-500] once the axis moves away from the DOG signal. The axis starts to move after 500 pluse
output completes in the negative direction.
Low 16-bit [000E] is Mode 14; when the DOG signal is received, the axis moves in the positive direction; after the
axis moves away from the DOG signal, a clear signal is outputted (20ms).
6-882
2705 D PLSV S，D1，D2 Adjustable pulse output

S      
D1 
D2   DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S  
D1 
D2 

－－ AS
Symbol
S ： Pulse output frequency
D2 ： Pulse direction output device
Explanation
6_
1. This instruction adjusts the pulse output frequency and direction (S) for the devices specified in D and D2. S specifies
the pulse output frequency: for line driver output models, the range is between -4 MHz to +4 MHz; for open collector
output models, the range is between -200 kHz to +200 kHz. The minus sign and plus sign indicate the positive
direction and negative pulse direction. You can change the pulse output frequency during the pulse output; but if the
new frequency is different from the previous frequency in direction, the instruction stops the output, and one cycle
later it outputs the target frequency again in the new direction.
2. Refer to the following table for the selection of pulse output devices for D1 and D2. When the output mode for D1
and D2 is not the default Pulse+direction output (0 is the default value), modify the mode by setting SR to 1, which
changes the mode to A/B phase output.
Direction output point for D2 Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
6-883
SR460 SR480 SR500 SR520 SR540 SR560

Output present register
SR461 SR481 SR501 SR521 SR541 SR561
3. The output point for the pulse direction output device D2 is affected by the scan cycle if it is not the recommended
output point in the table above.
4. The pulse direction output device D2 changes its own state according to the minus or plus sign in S. D2 is OFF if S
is plus (+) and D2 is ON if S is minus (-).
5. There is no ramp-up or ramp-down setting in the instruction. The instruction does not perform a ramp-up
operation at the beginning or ramp-down at stopping. If you want the ramp-up and ramp-down function, use the
DRAMP instruction (API 0703) for increasing and decreasing the pulse output frequency.
6. While the instruction is executing the pulse output, the output immediately stops if the drive condition changes to
OFF.
up the time for directional outputting goes first before pulse outputting. So that you can be sure the outputting only
happens when switching to the direction outputs. The unit for SR is millisecond and the range is 0-20 ms. Default is
0, indicating inactive.
_6 Output point for D1 Y0.6 Y0.7 Y0.8 Y0.9 Y0.10 Y0.11
8. Refer to Example 3 from the DJOG instruction (API 2703) for programming in ST language.
Example
When M10 is ON, Y0.0 outputs the pulse at 20 kHz. Y0.1 = OFF means the positive direction for the pulse output.
6-884
2706 D DRVI S1，S2，D1，D2 Relative Position control

S1      
S2      
D1 
D2  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
D1 
D2 

－－ AS
Symbol
S1 ： Number of output pulses (relative positioning)
S2 ： Pulse output frequency
：
6_
D1 Pulse output device
Explanation
1. This instruction specifies the output pulse setting for relative positioning. S1 is the number of output pulses (relative
positioning). The range is between -2,147,483,648 to +2,147,483,647, and the +/- signs indicate the positive and
negative pulse directions. When the instruction is executed and S1 is 0, it indicates not outputting and output
completion flag not be set to ON. If 0 is a possible output number in your program, it is suggested to add more
conditions in your program to rule out this possibility.
2. S2 is the pulse output frequency, and the range is between 0 Hz–200 kHz for open collector output models and 0–4
MHz for line driver output models. If the value in S2 is less than the Start/end frequency (Hz) set in SR (refer to the
SR table below for more details), PLC operates according to the values set in SR.
3. Refer to the following table for the selection of pulse output devices for D1 and D2. When the output mode for D1
and D2 is not the default Pulse+direction output (0 is the default value), modify the mode by setting SR to 1, which
changes the mode into A/B phase output.
6-885
Direction output point for

Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
D2
DDRVI and DDRVA support the output devices for D1 which can be the odd points as shown in the following table.
Only the Pulse+direction output mode is supported. It is not recommended that you use the input points Y0.0, Y0.2–
Y0.10 as the high-speed output points.
Direction output point for

Y1.0 or above or any M device (BOOL)
D2
4. The output point for the pulse direction output device D2 is affected by the scan cycle if it is not the recommended
output point in the table above.
5. When D2 uses the output mode Pulse+direction and S1 has a minus sign, D2 is ON. When S1 has a plus sign, D2 is
OFF. D2 is not OFF immediately after the pulse output in the negative direction is completed. D2 switches to OFF
_6 when the contact for the execution of the instruction is OFF.
6. For the instruction execution, you must use the parameters such as the start/end frequency and ramp-up/down
time. Refer to the following table for SM/SR corresponding to the axes.
The following table applies when D1 selects the even output points as the output devices.
Reversing the output

SM462 SM482 SM502 SM522 SM542 SM562
direction
Stop flag SM463 SM483 SM503 SM523 SM543 SM563
Enabling S curve
SM468 SM488 SM508 SM528 SM548 SM568
ramp-up/down
Enabling fixed slope

SM469 SM489 SM509 SM529 SM549 SM569
ramp-up/down
6-886
Output completion
SM470 SM490 SM510 SM530 SM550 SM570
auto-reset
Executing an interrupt
program when pulse SM471 SM491 SM511 SM531 SM551 SM571
output ends
Corresponding
I500 I501 I502 I503 I504 I505
interrupt I number
The output
immediately stops
SM476 SM496 SM516 SM536 SM556 SM576
when the instruction is
disabled or stops
Start/end frequency
SR463 SR483 SR503 SR523 SR543 SR563
(Hz）
Ramp-up time (ms) SR464 SR484 SR504 SR524 SR544 SR564
Ramp-down time (ms) SR465 SR485 SR505 SR525 SR545 SR565
Target frequency of SR472 SR492 SR512 SR532 SR552 SR572
the fixed slope SR473 SR493 SR513 SR533 SR553 SR573

6_
S curve mode SR604 SR605 SR606 SR607 SR608 SR609
frequency SR611 SR613 SR615 SR617 SR619 SR621
The following table applies when D1 selects the odd output points as the output devices.
Output stop flag SM474 SM494 SM514 SM534 SM554 SM574
Output completion
SM475 SM495 SM515 SM535 SM555 SM575
auto-reset
The output
immediately stops
SM477 SM497 SM517 SM537 SM557 SM577
disabled or stops
6-887
Start/end
SR476 SR496 SR516 SR536 SR556 SR576
frequency(Hz）
Ramp-up/down time
SR477 SR497 SR517 SR537 SR557 SR577
（ms）
Some flags, such as S curve ramp-up/down, fixed slope ramp-up/down, and executing an interrupt program when
pulse output ends, are not supported by the odd output points.
If the output is ongoing, the preset output is the ramp-down stop when the instruction is disabled or stops
temporarily. If the output must be stopped immediately, set the immediately stop flag to ON.
7. For PLC with FW V1.06.00 or later, added new SR652, SR653 for displaying number of pulse in ramp-up area and
new SR654, SR655 for displaying number of pulse in ramp-down area.
Refer to the following table for Attribute, Factory default and latched values of SM/SR corresponding to the axes.
Factory
Item Attribute StopRun RunStop Power ON Latched
default
Busy flag R OFF OFF OFF OFF N
Completion flag R/W OFF OFF OFF OFF N
_6 Stop flag R/W OFF OFF OFF OFF N
Output completion N
R/W OFF OFF OFF OFF
auto-reset
Enabling S curve N
R/W OFF OFF OFF OFF
ramp-up/down
Enabling fixed slope N

R/W OFF OFF OFF OFF
ramp-up/down
Executing an interrupt N
program when pulse R/W OFF OFF OFF OFF
output ends
The output N
immediately stops
R/W OFF OFF OFF OFF
disabled or stops
6-888
Present output
R / Wd No change No change No change 0 Y
position
Start/end Y
R / Wd No change No change No change 200
frequency(Hz）
Ramp-up time（ms） R / Wd No change No change No change 200 Y
Ramp-down time Y
R / Wd No change No change No change 200
（ms）
Target frequency of R / Wd Y
No change No change No change 0
the fixed slope
S curve mode R / Wd No change No change 0 0 N
Present output
R 0 0 0 0 N
frequency
Note: R mean the device is readable. W means the device is writable. Wd means the device is writable any time
except when performing the high-speed output.
8. After output completion auto-reset is enabled, the flag is automatically reset to OFF when the output completes.
You must set the flag to ON again if the auto-reset function is needed for the next output operation. It is suggested
that you use the rising-edge or falling-edge to trigger the flag every time. The function is usually used when the
output DDRVI instruction cannot be scanned and executed by PLC program after DDRVI is executed. For
example, when the instruction is executed in an interrupt program.

6_
9. If you use the Completion flag to set the I interrupt function, the flag is automatically reset to OFF when the output
completes and the interrupt program starts. You must set the flag to ON again for the next output in which the
interrupt occurs. It is suggested that you use the rising-edge or falling-edge to trigger the flag every time.
up the time for directional outputting goes first before pulse outputting. So that you can be sure the outputting only
happens when switching to the direction outputs. The unit for SR is millisecond and the range is 0-20 ms. Default is
0, indicating inactive.
6-889
Example 1
When M10 is ON, Y0.0 outputs 20,000 pulses at 2 kHz (relative positioning). Y0.1 = OFF means the positive direction.
Additional remarks
1. The following graph explains the relative positioning by specifying the travel distance from the current position with
the +/- signs.
F requency
+ 3, 000 pulse
Target frequency
S tart/end frequency
Current position
-3, 000 pulse
_6 2. Setting the ramp up/down and the items for relative positioning
a) Y0.0 output curve diagram
F requency
Number of
S1:: output pulses
Slope ramp-up
S2
SR463
Time
Ramp-up time Ramp-down time

SR464 SR465
b) You can create several DRVI instructions using the same output point in the program. The PLC can start only
one DRVI instruction when executing the program. For example, when one instruction starts Y0.0 for output,
then other instructions that also use Y0.0 for output are not executed. The instruction that starts the output
point first uses the point first.
c) After the instruction is executed, any modification of the parameters is not accepted until the instruction is
disabled.
6-890
3. Ramp-up and ramp-down for fixed slopes
a) The following graph shows the Y0.0 output curve diagram.
F requency
Fixed slope
Target frequency
Target frequency
Original slope
Time
Ramp-up time Ramp-down time

b) Start the fixed slope flag SM469 and write the target frequency of the fixed slope into SR472.
c) The new slope takes the place of the original slope and the DDRVI instruction performs the positioning as
shown above.
d) The general slope is determined by the start/end frequency, target frequency, and ramp up and down time.
The fixed slope is determined by the start/end frequency, target frequency of the fixed slope, and ramp up
and down time.
e) When the target frequency of the fixed slope is less than the target frequency, the fixed slope function is not
6_
started.
4. Stop flag and immediately stop flag
a) The following graphic shows the output diagram based on example 1.
Ramp-down stop Immediately stop
6-891
b) Ramp-down stop
 When M10 is ON, the DDRVI instruction is executed and starts to output pulses, and SM460, the Busy flag
is ON.
 When the instruction is disabled (M10 is OFF) or the stop flag SM463 is ON, the state of the immediately
stop flag SM476 is confirmed.
 If the immediately stop flag SM476 is OFF, the output ramps down to stop and then the Busy flag SM460
is OFF.
 If M10 is not OFF and the stop flag SM463 is not ON after the instruction is executed, Y0.0 stops the output
after 20,000 pulses.
c) Immediately stop
 When M10 is ON, the DDRVI instruction is executed and starts to output pulses, and SM460, the Busy flag
is ON.
 If the instruction is disabled (M10 is OFF) or the stop flag SM463 is ON, the state of the immediately stop
flag SM476 is confirmed.
 If the immediately stop flag SM476 is ON, the output stops immediately and the Busy flag SM460 is OFF.
5. Hardware limit function
_6 a) The following graphic shows the output curve diagram of axis 1 (Y0.0/Y0.1).
Positive limit function Negative limit function
b) Operation of the positive limit

 Positive limit input point X0.6 is set in HWCONFIG and downloaded to the PLC. When SM464 is set to
ON, the positive limit function starts.
6-892
 DDRVI outputs 20,000 pulses in the positive direction. Note: the instruction does not output in the
positive direction if the positive limit point is ON when the function starts.
 When the limit input point X0.6 is triggered by the external mechanism and is ON, the condition for the
hardware positive limit function is met.
 DDRVI instruction stops the output immediately and the positive limit alarm SM465 is ON.
 If the condition for the hardware limit function is not met, Y0.0 stops the output after 20,000 pulses.
c) Operation of the negative limit

 Negative limit input point X0.7 is set in HWCONFIG and is downloaded to PLC. When SM466 is set to ON,
the negative limit function starts.
 DDRVI outputs 20,000 pulses in the negative direction. Note: the instruction does not output in the negative
direction if the negative limit point is ON when the function starts.
 When the limit input point X0.7 is triggered by the external mechanism and is ON, the condition for the
hardware negative limit function is met.
 DDRVI instruction stops the output immediately and the negative limit alarm SM467 is ON.
 If the condition for the hardware limit function is not met, Y0.0 stops the output after -20,000 pulses.
d) SM flags related to the limit function
Axis number Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6 6_
Enabling the
hardware positive SM464 SM484 SM504 SM524 SM544 SM564
limit
Positive limit alarm

SM465 SM485 SM505 SM525 SM545 SM565
flag
Enabling the
hardware negative SM466 SM486 SM506 SM526 SM546 SM566
limit
Negative limit alarm

SM467 SM487 SM507 SM527 SM547 SM567
flag
Note: The limit point alarm flag is read-only and is set or reset automatically by the PLC according to the state of
the start flag.
6-893
6. Software limit function
a) The following diagram shows the output curve diagram of axis 1 (Y0.0/Y0.1).
Positive limit function Negative limit function
b) Operation of the positive limit

 Positive software limit position is set in HWCONFIG (by setting SR580=11,000 for example). After downloading
the setting to the PLC, it means the positive limit function starts.
 DDRVI starts to output 20,000 pulses in the positive direction. Note: the instruction does not output in the
positive direction if the positive limit is exceeded when the function starts.
 When the current position SR460 > the limit position SR580, it means that the condition for the software limit
_6
function is met.
 DDRVI instruction stops the output immediately and the positive limit alarm SM465 is ON.
 If the condition for the limit function is not met, Y0.0 stops the output after 20,000 pulses.
6-894
c) Operation of the negative limit

 Negative software limit position is set in HWCONFIG (by setting SR582 = –11,000 for example). After
downloading the setting to the PLC, the negative limit function starts.
 DDRVI starts to output 20,000 pulses in the negative direction. Note: the instruction does not output in the
negative direction if the negative limit is exceeded when the function starts.
 When the current position SR460 < the limit position SR582, the condition for the software negative limit function
is met.
 DDRVI instruction stops the output immediately and the negative limit alarm SM467 is ON.
 If the condition for the software limit function is not met, Y0.0 stops the output after -20,000 pulses.
d) Rising-edge trigger
Limit function Contact A Contact B

Types Rising-edge trigger Falling-edgetrigger
Descriptions
When started: from low to When started: from high to
high and maintains at high low and maintains at low
e) SR related to the limit function
Axis number Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6 6_

Positive software limit SR580 SR584 SR588 SR592 SR596 SR600
Negative software SR582 SR586 SR590 SR594 SR598 SR602
limit position SR583 SR587 SR591 SR595 SR599 SR603
Positive output limit: the output stops immediately if the current position is greater than the positive limit position.
Negative output limit: the output stops immediately if the current position is less than the negative limit position.
When the positive and negative limits are both 0, the software limit function cannot start. Since the software limit
function checks the output position when the output instruction is scanned, stopping the output is affected by the
PLC scan. To quickly stop the output in real time, use the external input point as the limit point.
6-895
7. ST Example
Explanation
7.1 When M0 is ON, Y0.0 outputs 1000 pulses at 1 kHz.
7.2 When the pulse output completes, SM461 is ON and SM470=ON is triggered.
7.3 The pulse output restarts when M0 changes from OFF to ON again
7.4 When there are more than two high-speed output instructions in a program, do not use the variable name, M1,
repeatedly.
7.5 It is suggested not to use ST language in a program if there is any chance the outputting needed to be
stopped.
8. Function block example

_6
Main program
Function block 1
6-896
Function block 2
Explanation
When M0 is ON, Y0.0 outputs 10000 pulse at 1kHz. Y0.1 = OFF means the pulse output direction is positive.
9. Refer to PLSR instruciton (API2701) for more details on changing target frequency during outputting.
10. Changing the target position during outputting:
10.1 This function is only available for firmware version 1.02.30 or later. You cannot change outputting direction
even after the target position is changed. For example, if the original output target position is in the positive
direction, after the target positon is changed, it still outputs in the positive positive.
10.2 After you set the change flag, the changing happens when the instruction is being scanned. And after it is
changed, the change flag is cleared off. But if the target position is set incorrectly, the change flag keeps ON.
10.3 Refer to the following table for the corresponding outputs and change flag SM.
Output point Y0.0 Y0.1 Y0.2 Y0.3 Y0.4 Y0.5

SM number SM478 SM479 SM498 SM499 SM518 SM519
Output point Y0.6 Y0.7 Y0.8 Y0.9 Y0.10 Y0.11 6_
SM number SM538 SM539 SM558 SM559 SM578 SM579
10.4 This changing target posiiton funciton is available for DDRVI and DDRVA insturcitos. When the instruction
DDRVI is used and a change flag is set, the change will be executed. Even if the output number is 0, the
operation will be carried out and stop outputting. When the instruction DDRVA is used, if the changed target
position is the same as the previous one, this change will not be performed.
10.5 Three situations may occur, when changing target position during output.
Situation A: changing timing occurs during outputting in the ramp-down area.

 oringinal target position when started (blue)
 new number of output pulse >= remaining number of output pulse, its outputting curve (red).
 new number of output pulse < remaining number of output pulse, its outputting curve (green).
6-897
PLC change & clear

User set
Change SM
Freq.
Pulse no.



Situation B: changing timing occurs during outputting in the target frequency area.
 oringinal target position during initial start (blue)
 new number of output pulse >= number of output pulse in ramp-down area, its outputting curve
(red).
 new number of output pulse < number of output pulse in ramp-down area, its outputting
curve(green)
PLC change & clear
User set
Change SM
Freq.
Pulse no.
_6



Situation C: changing timing occurs during outputting in the ramp-up area.
 oringinal target position during initial start (blue)
 new number of output pulse >= number of output pulse in ramp-down area, its outputting curve
(red).
 new number of output pulse < number of output pulse in ramp-down area, its outputting
curve(green)
User set
PLC change & clear
Change SM
Freq.
Pulse no.



6-898
2707 D DRVA S1，S2，D1，D2 Absolute position control

S1      
S2      
D1 
D2  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
D1 
D2 

－－ AS
Symbol
S1 ： Number of output pulses (absolute positioning)
S2 ： Pulse output frequency
D1 ： Pulse output device 6_

Explanation
1. This instruction specifies the output pulse setting for absolute positioning. S1 is the number of output pulses (absolute
positioning). The range is between -2,147,483,648 to +2,147,483,647, and +/- signs indicate the positive and
negative pulse directions. When the instruction is executed, it checks the current position with S1. If S1 is 0, it indicates
not outputting and output completion flag not be set to ON. If 0 is a possible output number in your program, it is
suggested to add more conditions in your program to rule out this possibility.
2. S2 is the pulse output frequency and the range is between 0 Hz–4 MHz for the line driver output models and 0 Hz–
200 kHz for the open collector output models. If the value in S2 is less than the Start/end frequency (Hz) set in SR
(refer to the SR table of DRVI instruction for more details), PLC operates according to the values set in SR.
3. Absolute positioning means that the instruction outputs pulses to move from current position until the specified target
position is reached. For example, the number of output pulses at current position is 100 and the number of pulses at
the target position S1 is set to 1000. So the number of the actual output pulses is 1000-100=900.
4. Refer to the DDRVI instruction (API 2706) for more explanation.
6-899
Example
If the value of the present output position SR460 (32-bit) is 100 and M10 is ON, then the DDRVA instruction causes Y0.0
to output pulses at 2 kHz until the value in SR460 becomes 20,000 (absolute positioning). Y0.1 = OFF means the positive
direction.
Additional remarks
1. The following graph shows absolute positioning: the way of specifying the distance from the center (zero point).
F requency
+ 3, 000 pulse
Target frequency
_6
Zero point
0 pulse
6-900
2708 CSFO S1，S2，S3，S4，S5，D1，D2 Catch speed and proportional output

S1 
S2 
S3 
S4 
S5 
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
type INT
S1 
S2  
S3  
S4 
S5 
D1 
D2  

－ AS -
6_
Symbol
S1 ： Signal input device
S2 ： Number of input pulses
S3 ： Pulse input frequency

Denominator (output frequency) for the proportion of the input
S4 ：
frequency and output frequency
S5 ： Numerator (input frequency) for the proportion of the input

frequency and output frequency
D2 ： Pulse output frequency
Explanation
1. This instruction specifies the catch speed and proportional output. S1 can only specify X0.0, X0.2, X0.4, X0.6, X0.8
and X0.10 as the input points, and the operand occupies two consecutive input points. You cannot execute the
instruction if the input points are the points specified for S1 above. After you select the input points, the high-speed
counter is automatically specified. If there is a DCNT instruction (API 1004) with the same high-speed counter in
6-901
the program, the PLC first executes the instruction that starts the counter first. The input points and corresponding
high-speed counters are shown in the following table.
Group number 1 2 3 4 5 6
S1+0 input point

X0.0 X0.2 X0.4 X0.6 X0.8 X0.10
(Phase A)
S1+1 input point

X0.1 X0.3 X0.5 X0.7 X0.9 X0.11
(Phase B)
High-speed counter
HC202 HC206 HC210 HC214 HC218 HC222
number
Flag for reversing

SM270 SM271 SM272 SM273 SM274 SM275
input direction
2. If the high-speed counters for the instruction can use only the phase A/B input mode, set the flag for reversing the
input direction to ON when MPG is connected but has not rotated yet, and the PLC input point is ON. Set the
function to detect the state of PLC run cycle to OFF.
3. S2 is the number of input pulses. Use a 32-bit variable to declare the parameter.
4. S3 is the frequency of input pulses. Use a 32-bit variable to declare the parameter with the unit of 1 Hz.
5. S4 is the denominator (output frequency) for the proportion of the input frequency and output frequency. S5 is the
_6 numerator (input frequency) for the proportion of the input frequency and output frequency. The range of S4 and S5
is between 1–255. If the setting value exceeds the range, the instruction is processed as the maximum or minimum
value. For example, if input frequency: output frequency= 5:3, the denominator output frequency is K3 and the
numerator input frequency is K5. If the input frequency: output frequency=1:2, the denominator output frequency is
K2 and the numerator input frequency is K1.
6. D1 can only specify Y0.0, Y0.2, Y0.4, Y0.6, Y0.8 and Y0.10 as the output points and occupies two consecutive
output points.
The output points and corresponding output mode SR are shown in the following table.
Output axis number 1 2 3 4 5 6
D1+0 output point Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
D1+1 output point Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
7. D2 is the frequency of the output pulses. Use a 32-bit variable to declare the parameter with the unit of 1 Hz.
6-902
8. There is no limit to the number of times you can use this instruction; but the high-speed input and output points
cannot be used by other instructions when this instruction is executed. Otherwise, the instruction cannot be
executed.
only once.
Notes
1. The PLC calculates the input pulse frequency based on the input pulse width (ON) in the positive half cycle. If the
proportion of the pulse width for ON:pulse width for OFF is not 1:1, the PLC takes the ON width as the standard for
conversion by default.
2. The input pulse=ON means the input point LED is on. When using the MPG but it has not rotated yet, you can check
if the input point LED is OFF and the flag for reversing the input direction is activated .
3. For PLC with FW V1.04.70 (V1.04.70 included) or later, the minimum pluse frequence for input and output is 50 Hz.
If the actual input pulse is 10 Hz and the value in S3 shows 10 Hz. But since the minimum pulse frequence for output
is 50 Hz, the instruction uses 50 Hz instead of 10 Hz to calculate. For the ratio 1:2, after conversion, the output pulse
is 100 Hz. For the ratio 2:1, after conversion, the output pulse is 50 Hz instead of 25 or 5 Hz.
4. You can modify values in S4 or S5 during the execution of this instruction. But you need to re-execute this instruction
to actualize this modification. Otherwise the value in S2 is not accurate enough to be used for calculating the current
output position of SR. 6_

5. After conversion, if the output pulse frequecne exceeds the maximum limit, the error code is recorded as 16#2030 in
Error Log File in ISPSoft and SM29 is ON. SR29 is the axis number. This function is available for PLC with FW
V1.06.20 (V1.06.20 included) or later.
6. If the input pulse is 0 Hz and lasts for more than 2 seconds, PLC stops outputting automatically and the error code is
recorded as 16#2031 in Error Log File in ISPSoft and SM29 is ON. SR29 is the axis number. This function is
available for PLC with FW V1.06.20 (V1.06.20 included) or later.
Example 1
X0.0/X0.1 input pulses for detecting the MPG. When M0 is ON, the setting values of S4 and S5 are both 1 (D4=1 and
D5=1). When the input frequency is 10 Hz (D2, D3=10) and the number of pulses is 10 (D0, D1=10), the output axis
(Y0.0/Y0.1) outputs 10 pulses (SR460, SR461=10) at 10Hz (D10, D11=10).
6-903
Example 2
When M0 is ON, the setting values of S4 and S5 are 3 and 5 (D4=3, D5=5) respectively. When the input frequency of the
MPG is 500 Hz (D2, D3=500) and the number of pulses is 2500 (D0, D1=2500), the output axis (Y0.0/Y0.1) outputs 1500
pulses (SR460, SR461=1500) at 300 Hz (D10, D11=300).
_6
6-904
2709 D DRVM S1，S2，S3，S4，S5，S6，D1，D2 Mark alignment positioning

S1    
S2    
S3  
S4    
S5    
S6    
D1 
D2  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3 
S4  
S5  
S6  
D1 
D2 
Pulse Instruction 16-bit instruction 32-bit instruction 6_

－－ AS
Symbol
S1 ： Target number of output pulses
S3 ： Input point number for receiving the external interrupt signal
S4 ： The number of output pulses at the end for the fore mask section
S5 ： The number of output pulses at the beginning for the rear mask section
The number of output pulses in the ramp-down process after the
S6 ：
interrupt signal is received
D2 ： Direction pulse output device
6-905
Explanation
1. This instruction performs mark alignment positioning. When the value of S1 is 0, it indicates the output is a
maximum 32-bit value (with a sign) and the output does not perform the ramp-down stop until receiving the mark
signal.
If the value of S1 is not 0 and the external interrupt does not occur, the target number output pulses are output. The
range of S1 is between -2,147,483,648 to +2,147,483,647, and the +/- sign means the positive or negative direction.
2. When the value of S2 is less than or equal to 0, the output is not enabled. If the output frequency is greater than the
maximum frequency, the PLC processes it as the maximum output frequency.
3. S3 can specify the M or X device as the input point. The input source signal is affected by the scan cycle if the
selected input point is not in X0.0–X0.15 in the PLC.
4. You must use the instruction by combining the input point number and the external interrupt program to achieve the
real-time ramp-down output. For the rising-edge or falling-edge trigger for the external interrupt, select the triggers
in the external interrupt program in ISPSoft.
A. Using the external interrupt (e.g. I0xx, I1xx): when the external interrupt occurs, the ramp-down stop is
performed after the mark signal is received. No operation is performed if the external interrupt is not enabled.
B. Without using the external interrupt (I0xx, I1xx): When the instruction is executed, the ramp-down stop is
performed after the mark signal is received if the rising edge occurs at X point or M device. It is affected by the
_6 scan time.
5. The number of output pulses in the fore mask section is between 1–S4. When the setting value for S4 is 0, it means
the fore- mask section function is disabled. When the number of pulses to be masked exceeds the value of S1, the
instruction takes the target number of output pulses S1 as the number to be masked. If the external input trigger
occurs within the number of output pulses to be masked, the external input interrupt is automatically invalid.
6. The number of output pulses in the rear mask section is between S5 and S1. When S5 =0 or S5 >=S1, the rear mask
section function is disabled. When the external input trigger occurs in the masked sections, the external input
interrupt is automatically invalid. When S4 >S5, it indicates the external input interrupt is invalid in the output process.
7. If the fore and rear mask sections are both set and S4 < S5, the valid input interrupt occurs in the section between
S4+1 and S5-1.
S6: the number of output pulses in the ramp-down Description
the ramp-down stop is performed based on the ramp-

If S6 is set to 0 after the mark signal is received
down time
6-906
If S6 =-1 or < 0 after the mark signal is received the output immediately stops
The instruction limits the target frequency and

If the setting value of S6 is not enough to achieve the
performs the ramp-down stop in accordance with the
ramp-down stop within the ramp-down time,
set ramp-down time
The instruction outputs the number of redundant
If S6 is greater than the number of pulses output within pulses with the same output frequency when the
the ramp-down time, interrupt is triggered, and then performs the ramp-
down process
9. For PLC with FW V1.06.00 (V1.06.00 included) or later: If S6 is set to 0 after the mark signal is received, it means
that the ramp-down stop is performed based on the ramp-down time. If S6 is set to -1 after the mark signal is
received, it means that the output immediately stops. If S6 is set to >0 after the mark signal is received and if the
setting value of S6 is not enough to achieve the ramp-down stop within the ramp-down time, the instruction limits
the target frequency and performs the ramp-down stop in accordance with the set ramp-down time. If S6 is greater
than the number of pulses output within the ramp-down time, the instruction outputs the number of redundant
pulses with the same output frequency when the interrupt is triggered, and then performs the ramp-down process.
S6: the number of output pulses in the ramp-down Description
If S6 = > 0 after the mark signal is received The instruction limits the target frequency and
performs the ramp-down stop in accordance with the

If the setting value of S6 is not enough to achieve the
6_
set ramp-down time
ramp-down stop within the ramp-down time,
If S6 = > 0 after the mark signal is received The instruction outputs the number of redundant
pulses with the same output frequency when the
If S6 is greater than the number of pulses output within
interrupt is triggered, and then performs the ramp-
the ramp-down time,
down process
If S6 is set to 0 after the mark signal is received

The ramp-down stop is performed based on the ramp-
down time
If S6 =-1 after the mark signal is received The output immediately stops
If S6 =< -1 after the mark signal is received

The instruction does NOT limit the target frequency
If the setting value of S6 is not enough to achieve the and after outputting the number of output pulses, the
ramp-down stop within the ramp-down time, output stops immediately
If S6 =< -1 after the mark signal is received The instruction outputs the number of redundant
pulses with the same output frequency when the
6-907
If S6 is greater than the number of pulses output within Interrupt is triggered, and then performs the ramp-
the ramp-down time, down process
 Added new SR652, SR653 for displaying number of pulse in ramp-up area and new SR654, SR655 for
displaying number of pulse in ramp-down area.
10. If the output has entered the ramp-down process when the external input interrupt trigger occurs, the instruction
completes the output of the number of pulses specified by S6.
11. See the following timing diagram about the output, interrupt trigger, mask and relevant flags. For the completion
flag, refer to the Completion flag SM for the axes in DDRVI instruction (API 2706).
EN
S4 S5
S3
finish flag
S2
D1
Time
0
Pulse No.
_6 S6
S1
12. The target frequency S2 of the instruction can be modified in the process of the pulse output. Since the number of
output pulses in the ramp-down section has been set when the instruction is executed, the timing diagram for
changing the frequency is shown as the following dashed line.
S3
Change S2
S2
D1
Time
Pulse No.
S6
13. Refer to the DDRVI instruction (API 2706) for the selection of pulse output devices for D1 and D2. The output points
for D1 can only be even-numberd such as Y0.0, Y0.2 or Y0.10. If the output points are not the recommended ones,
the direction output D2 is affected by the scan cycle.
6-908
only once.
Example 1
X0.4 external interrupt program
Notes
6_
1. When M0 changes from OFF to ON, Y0.0 starts to output pulses. After outputting more than 30,000 pulses, the
external interrupt is detected on X0.4. The value in D0 increases by 1 and the pulse output stops after 15,000 pulses
(S6 = 15,000). If the interrupt does not occur, the output does not stop until 100,000 pulses are output.
2. If the number of output pulses is between 1–30,000, they are in the fore mask section. The external interrupt occurs
at X0.4 at the moment and the instruction does not perform the ramp-down stop operation.
3. If the number of output pulses is between 70,000–100,000, they are in the rear mask section. The external interrupt
occurs at X0.4 at the moment and the instruction still does not perform the ramp-down stop operation.
4. When the pulse output completes, SM461 is ON and M0 is reset.
6-909
Additional remarks
1. The alignment mark function and mask function:
 When DDRVM is executed, the pulse output starts.
 When the interrupt occurs for the mark alignment, the ramp-down process starts and the output stops after the
number of the pulses specified by S6.
 When the interrupt for the mark alignment does not occur or has no effect, DDRVM stops outputting the pulses
after the target number of pulses specified by S1.
S4: The number of output pulses in the fore mask section. If the interrupt occurs in this section, the interrupt is
ineffective for the mark alignment.
S5: The number of output pulses in the rear mask section. If the interrupt occurs in this section, the interrupt is
ineffective for the mark alignment.
S2: The target output frequency
_6
6-910
2. The mark alignment function is enabled in the ramp-up and target frequency and ramp-down sections. (Horizontal
coornate (x axis) represents TIME and vertical coornate (y axis) represents PULSE.)
When the mark alignment function is not enabled, set S1 = 100,000; the output stops after 100,000 pulses.
 Green line: signal of mark aligment
 Blue line: the actual output speed
100,000 pulse
Case 1: when the mark alignment occurs in the ramp-up section
The operation of the mark alignment (green line: OFF -> ON) begins when the number of pulses is 3000. The target
frequency of 10 kHz cannot be reached even if S6 is 15,000.

6_
15,000 pulse
6 - 9 11
Case 2: when the mark alignment occurs in the ramp-up section
The operation of the mark alignment (green line: OFF -> ON) begins when the number of pulses is 6000. The target
frequency of 10 kHz can be reached if S6 is 15,000.
15,000 pulse
When the mark alignment occurs in the target frequency section
_6 The operation of the mark alignment (green line: OFF -> ON) begins when the number of pulses is 50,000. Set S6 =
15,000; the output stops after 15,000 pulses.
15,000 pulse
6-912
Case 1: when the mark alignment occurs in the ramp-down section
The operation of the mark alignment (green line: OFF -> ON) begins when the number of pulses is 95,000.
Set S6 = 15,000; the output stops after 15,000 pulses at the current speed.
15,000 pulse
Case 2: when the mark alignment occurs in the ramp-down section
The operation of the mark alignment (green line: OFF -> ON) begins when the number of pulses is 95,000. After the 6_
mark alignment, set S6 to -1, the output stops immediately.
6-913

2-Axis relative-coordinate point-to-
2710 D PPMR S1，S2，S3， D1，D2

S1      
S2      
S3      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
type INT
S1  
S2  
S3  
D1 
D2 

－－ AS
Symbol
S1 ： Number of output pulses for the X axis

_6
S2 ： Number of output pulses for the Y axis
S3 ： Maximum point-to-point output frequency
D1 ： Pulse output device for the X axis
D2 ： Pulse output device for the Y axis
Explanation
1. This instruction performs 2-axis relative-coordinate point-to-point synchronized motion. S1 and S2 specify the
number of output pulses (relative positioning) for the X and Y axes. The range is between: -2,147,483,648 to
+2,147,483,647, and the +/- sign indicates the positive/negative direction.
2. S3 specifies the maximum point to point output frequency. The range is between 1 Hz–200 kHz.
3. D1 and D2 are the output devices for the X and Y axes respectively. You can designate the following six axes for
output but you cannot change the fixed direction output points. The direction signal: OFF means in positive direction
and ON is in negative direction. If you do not use the preset Pulse+direction output mode (default: 0), change the
output mode by setting SR to 1.
6-914
Output points for D1

Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
and D2
Fixed direction
Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
output point
4. The PLC assigns the value of S3 to the X or Y axis depending on which outputs the largest number of pulses. If the
numbers of pulses output for the two axes are excessively different, so that no proper output frequency can be
calculated through the numbers of their output pulses, the PLC automatically decreases the maximum point to point
frequency and without any error message appearing.
5. The instruction uses the parameters such as the start and end frequencies and ramp-up and ramp-down times for
the axes the instruction executes. Instead of the originally configured parameters for the axes, the X axis
parameters are taken as the reference source. For example, when the X axis selects axis 1 and the Y axis selects
axis 3 for the output, axis 1 parameters become the parameter sources for the start frequency and ramp up and
ramp-down time.
6. The following table shows the flags for the axes and the corresponding SM/SR.

6_
Start/end frequency SR463 SR483 SR503 SR523 SR543 SR563
Ramp-up time SR464 SR484 SR504 SR524 SR544 SR564
Ramp-down time SR465 SR485 SR505 SR525 SR545 SR565
7. There is no limit to how many times you can use the instruction in a program. But during the execution of the
instruction, it cannot execute the output (if the Y axis output is being used) until the Y axis completes its output and
is released.
8. When the 2-axis synchronized pulse output completes, the corresponding Completion flags for the two axes is set.
Since the same timing for the completion of the 2-axis synchronized pulse output cannot be ensured every time, the
program should check the Completion flags of both axes before executing the next user program.
6-915
Example (Ladder diagrams)
1. Draw a rhombus as shown below.
Y軸
(0, 0)
X軸
(-2 7000, -270 00) (27 000, -27000 )
(0,-5 5000)
2. Steps:
 Set the coordinates of four points (0, 0), (-27000, -27000), (0, -55000), (27000, -27000) as in the figure
above. Calculate the relative coordinates of the four points and obtain (-27000, -27000),
(27000, -28000), (27000, 28000), and (-27000, 27000). Place them in the 32-bit registers (D200, D202), (D204,
D206), (D208, D210), (D212, D214).
 RUN the program in the PLC. Set M0 to ON to start the 2-axis line drawing.
_6
6-916
6_
3. Operation:
When PLC runs the program and M0 is ON, the PLC starts the first point-to-point motion at 100 kHz. D0 increments by 1
whenever a point-to-point motion is completed and the second point-to-point motion starts to execute automatically. The
operation pattern repeats until the fourth point-to-point motion completes.
Example 2 (ST program)
6-917
Explanation
1. When M0 is ON, Y0.0 and Y0.2 outputs 1000 pulses at 1kHz simultaneously. When M1 is ON, it indicates Y0.0 and
Y0.2 are used for high-speed pulse output.
2. When the Y0.0 pulse output is completed, SM461 is ON. When the Y0.2 pulse output is completed, SM481 is ON.
And if M1 is also ON, it triggers SM470 (output completion auto-reset for Y0.0) and SM490 (output completion
auto-reset for Y0.2) to be ON. Y0.0 and Y0.2 are free and ready to be used again and M1 is cleared to OFF.
3. When M0 switches from OFF to ON, the pulse output is restarted.
4. When there are more than two high-speed output instructions in a program, do not use the variable name, M1,
repeatedly.
5. It is suggested not to use ST language in a program if there is any chance the outputting needed to be stopped.
_6
6-918

2-Axis absolute-coordinate point-to-
2711 D PPMA S1，S2，S3， D1，D2

S1      
S2      
S3      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
D1 
D2 

－－ AS
Symbol
S1 ： Number of output pulses for the X axis
S2 ： Number of output pulses for the Y axis 6_

S3 ： Maximum point-to-point output frequency
Explanation
1. This instruction performs 2-axis absolute-coordinate point-to-point synchronized motion. S1 and S2 specify the
number of output pulses (absolute positioning) for the X and Y axes.
2. For more information, refer to the DPPMR instruction (API 2710).
6-919
Example
1. Draw a rhombus as in the figure below.
A xis Y
(0,0)
Axis X
(-27,000, -27,000) (27,000, -27,000)
(0, -55,000)
2. Steps:
 Set the four coordinates (-27000, -27000), (0, -55000), (27000, -27000) and (0, 0) as in the
figure above. Place them in the 32-bit registers (D200, D202), (D204, D206), (D208, D210),
(D212, D214).
 RUN the program in the PLC. Set M0 to ON to start the 2-axis line drawing.
_6
6-920
3. Operation:
6_
When PLC runs the program and M0 is ON, the PLC starts the first point-to-point motion at 100 kHz. D0 increments by 1
whenever a point-to-point motion completes and the second point-to-point motion starts to execute automatically. The
operation pattern repeats until the fourth point-to-point motion completes.
6-921

2712 D CICR S1，S2，S3，S4，S5，D1，D2
interpolation

S1      
S2      
S3       
S4      
S5      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3   
S4  
S5  
D1 
D2 

－－ AS
_6
Symbol
S1 ： X axis target coordinate (relative positioning)
S2 ： Y axis target coordinate (relative positioning)
S3 ： The shift of the center or the central angle
S4 ： Target reference frequency
S5 ： Function selection
Explanation
1. S1, S2 and S3 respectively designate the X axis target coordinate, Y axis target coordinate (relative position) and the
shift of the center or a central angle of a circle. Refer to the following clockwise arc operation for details.
2. D1 and D2 are the pulse output devices for the X and Y axes respectively. Refer to the DPPMR instruction (API
2710) for the selection of output points and output modes for the axes.
6-922
3. S4 sets the target frequency for the reference. The target reference frequency is used for the prior calculation when
the PLC plans the travel path for the arc after the instruction is executed. But if the estimated calculation process
cannot achieve the arc travel path, the output frequency is automatically decreased to fulfill the synchronized arc
drawing function.
4. S5 is the setting value for function selection. See the descriptions below.
S3 : The shift of the center or central

Setting value in S5 Description
angle
The arc resolution uses a 10° arc as the basic

0 Shift of the center (32-bit integer type)
angle for motion.

angle for motion.

angle for motion. (FW V1.04.60 or later)

10 Shift of central angle (floating point type)

6_
Seen as setting value in S5 is 0
Other Shift of the center (32-bit integer type)

angle for motion.
5. Refer to Example 2 of the DPPMR instruction for more details on ST language programming.
6-923
Drawing a clockwise arc
1. Define the four quadrants (QI, QII, QIII and QIV) of a coordinate system as in the graph below. Point A indicates the
current coordinates on the X and Y axes.
II I
X
A
III IV
2. Point B is the target coordinates specified by S1 and S2. Point O is the center of a circle enclosing both point A and
point B.
3. For PLC with FW V1.04.59 or previous versions, S3 is the distance to shift the center point O. For PLC with FW
V1.04.60 or later, S3 can also be the distance to shift the center point or central angle, if it is defined as the central
angle, it is the included angle of AOB.
4. The point A represents the origin of the axes X and Y in a plane. The target point B can be in Quadrant I, II, III, IV of
the plane. Use the target point B to connect to the point A to draw a line and then use the setting values (shift the
center point or central angle) in S3 to define an arc travel path.
_6 The figures below show 2 arc-travel path examples (solid lines) when the point B is in Quadrant I and IV with
different setting values in S3 (shift the center point). (r: radius)
S3 >= 0
O
S3 < 0 B
A
r O
r
A
S3>= 0 S3< 0
6-924
5. The figures below show 2 arc-travel path examples (solid lines) when the point B is in Quadrant I and IV with
different setting values in S3 (shift the central angle). (r: radius)
S3<= 180.0 S3> 180.0
6. The figures below show 2 arc-travel path examples (solid lines) when the point B is in Quadrant II and III with
S3 < 0
O
S3 >= 0 A B O
r
r
6_
B
S3>= 0 S3< 0
S3<= 180.0 S3> 180.0
6-925
Example
1. Draw a DELTA LOGO as the figure below.
2. Steps: divide the logo into three parts.
 For an ellipse: use the DCICR instruction for the relative-position clockwise arc interpolation.
 The absolute coordinates of the ellipse: P1（39930，-9982）, P2（-9982，39930）, P3（73206，123119） and
P4（123119，73206）.
_6  Taking （39930，-9982）as the starting point, yields these relative coordinates: （-49912，49912）, （83188，
83189）, （49913，-49913） and （-83189，-83188）.
6-926
6_
When the PLC runs the program and M1 is ON, the PLC starts drawing the first segment of the arc. D1
increments by one when a segment of arc is completed and the second segment of the arc starts to
automatically execute. This operation pattern repeats until the fourth segment of arc is completed.
When D1=1, using DCICR, the PLC draws the first-segment arc from P1 to P2 with the shift of the center of the
circle: 18825 and arc resolution: 5.
When D1=2, using DCICR, the PLC draws the second-segment arc from P2 to P3 with the shift of the center of the
When D1=3, using DCICR, the PLC draws the third-segment arc from P3 to P4 with the shift of the center of the
When D1=4, using DCICR, PLC draws the fourth-segment arc from P4 to P1 with the shift of the center of the circle:
110295 and arc resolution: 5.
6-927
 For a circle = use DCCMR instruction (API 2716) for the relative-position circle drawing.
 The absolute coordinates of the circle: P5（86213，15435） and P6（103048，37425）. Taking （86213，
15435） as the starting point, yields the relative coordinates for the center of the circle as （16835，21990）.
When the PLC runs the program and M2 is ON, the PLC starts to draw the relative-position circle with the target
reference frequency of 20 kHz.
 For a delta, use DPPMA (API 2711) for the absolute-position 2-axis synchronized motion.
 Absolute coordinates of the delta= starting point P7 (-80360，23641), P8 (208552，-23641) and P9 (62096，
206884).
_6
6-928
When the PLC runs the program and M0 is ON, the PLC starts drawing the first segment of the 2-axis synchronized
motion at 50 kHz. D1 increments by one when a segment of the 2-axis synchronized motion completes and the
second segment of 2-axis synchronized motion starts to automatically execute. The operation pattern repeats until
the third segment of 2-axis synchronized motion completes.

6_
When D1=1, the PLC starts to draw the line from P7 to P8 with the DPPMA instruction.
6-929

2-Axis absolute-
2713 D CICA S1，S2，S3，S4，S5，D1，D2 position clockwise arc
interpolation

S1      
S2      
S3       
S4      
S5      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3   
S4  
S5  
D1 
D2 

－－ AS
_6
Symbol
S1 ： X axis target coordinate (absolute positioning)
S2 ： Y axis target coordinate (absolute positioning)
S5 ： Function
Explanation
1. This instruction performs 2-axis absolute-position clockwise arc interpolation. S1 and S2 respectively
designate the X- and Y-axis target coordinates. For more explanation, refer to DCICR instruction (API
2712).
2. Refer to Example 2 from the DPPMR instruction (API 2710) for programming in ST language.
6-930

2-Axis relative-
2714 D CICCR S1，S2，S3，S4，S5，D1，D2 position counterclockwise arc
interpolation

S1      
S2      
S3       
S4      
S5      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3   
S4  
S5  
D1 
D2 

－－ AS 6_
Symbol
S1 ： X axis target coordinate (relative positioning)
S2 ： Y axis target coordinate (relative positioning)
S5 ： Function
6-931
Explanation
1. This instruction performs 2-axis relative-position clockwise arc interpolation. S1, S2 and S3 respectively designate
the target coordinate on X axis, target coordinate on Y axis, and the shift of the center of a circle. Refer to the
following operation for drawing the counterclockwise arc for details.
2. D1 and D2 are the output devices for the X and Y axes respectively. Refer to the DPPMR instruction (API 2710) for
the selection of output points and output mode for the axes.
the PLC plans the travel path for the arc, after the instruction is executed. If the estimated calculation process
cannot achieve the planned arc travel path, the output frequency is automatically decreased so as to fulfill the
synchronized arc drawing function.
S3 : The shift of the center or central

Setting value in S5 Description
angle

angle for motion.

angle for motion.
_6



Other Shift of the center (32-bit integer type)

angle for motion.
6-932
Drawing the counterclockwise arc
1. Define the four quadrants (QI, QII, QIII and QIV) of a coordinate system as below. Point A indicates the current
coordinates on X and Y axes.
II I
X
A
III IV
2. Point B is the target coordinates specified by S1 and S2. Point O is the center of a circle containing points A and B.
3. For PLC with FW V1.04.59 or previous versions, S3 is the distance to shift the center point O. For PLC with FW
V1.04.60 or later, S3 can also be the distance to shift the center point or central angle, if it is defined as the central
angle, it is the included angle of AOB.
4. The point A represents the origin of the axes X and Y in a plane. The target point B can be in Quadrant I, II, III, IV of
the plane. Use the target point B to connect to the point A to draw a line and then use the setting values (shift the
center point or the central angle) in S3 to define an arc travel path.
The figures below show 2 arc-travel path examples (solid lines) when the point B is in Quadrant I and IV with
different setting values in S3 (shift the center point). (r: radius) 6_

B
S3 < 0
O
S3 >= 0 B
A
r O
r
A
S3>= 0 S3< 0
6-933
5. The figures below show 2 arc-travel path examples (solid lines) when the point B is in Quadrant I and IV with
S3<= 180.0 S3> 180.0
S3 >= 0
O
S3 < 0 A
B
_6 r O
r
B
S3>= 0 S3< 0
S3<= 180.0 S3> 180.0
6-934
8. When the X axis coordinate = 0 and the Y axis coordinate >= 0 for target point B, then point B is defined as the
point staying in QI of point A. Whereas, if Y axis coordinate < 0 for target point B, then point B is defined as the
point staying in QIII of point A.
Example
1. Draw a DELTA LOGO as the figure below.
6_
2. Steps: divide the logo into three parts.
 For an ellipse: use the DCICR instruction (API 2712) for the relative-position counterclockwise arc interpolation.
 The absolute coordinates of the ellipse: P1(39930，-9982), P4 (123119，73206), P3 (73206，123119) and P2 (-
9982，39930)
 Taking (39930，-9982) as the start point, the obtained relative coordinates: (83189, 83188), (-49913, 49913), (-
83188，-83189) and (49912，-49912).
6-935
_6
6-936
When the PLC runs the program and M1 is ON, the PLC starts drawing the first segment of the clockwise arc at
50kHz. D1 increments by 1 when a segment of arc is completed and the second segment of arc starts to
automatically execute. The operation pattern repeats until the fourth segment of arc is completed.
When D1=1, using DCICCR, the PLC draws the first-segment arc from P1 to P4 with the shift of the center of the
circle: -110295 and arc resolution: 5.
When D1=2, using DCICCR, the PLC draws the second-segment arc from P4 to P3 with the shift of the center of
the circle: -18825 and arc resolution: 5.
When D1=3, using DCICCR, the PLC draws the third-segment arc from P3 to P2 with the shift of the center of the
When D1=4, using DCICCR, the PLC draws the fourth-segment arc from P2 to P1 with the shift of the center of the
 A circle = use DCCMR instruction (API 2716) for the relative-position circle drawing. Refer to the example in API
2712 DCICR for detailed operation.
 A delta = use DPPMA (APIU 2711) for the absolute-position 2-axis synchronized motion. Refer to the example in
DCICR (API 2712 ) for more information.
6_
6-937

2-Axis absolute-
2715 D CICCA S1，S2，S3，S4，S5，D1，D2 position counterclockwise arc
interpolation

S1      
S2      
S3       
S4      
S5      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3   
S4  
S5  
D1 
D2 

_6 －－ AS
Symbol
S1 ： X axis target coordinate (absolute positioning)
S2 ： Y axis target coordinate (absolute positioning)
S5 ： Function
Explanation
1. S1 and S2 respectively designate the target coordinate on the X axis and the target coordinate on the Y axis. For an
explanation of the instruction, refer to DCICCR instruction (API 2714).
6-938
2716 D CCMR S1，S2，S3，S4，D1，D2 Relative-position circle drawing

S1      
S2      
S3      
S4      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4  
D1 
D2 

－－ AS
Symbol
S1 ： X axis coordinate of the center (relative positioning) 6_

S2 ： Y axis coordinate of the center (elative positioning)
6-939
Explanation
1. This instruction draws a circle based on relative positioning. S1 and S2 are respectively the X and Y axis coordinates
of the center of a circle (relative position).
S3 : Function Selection Descriptions
0 The arc resolution uses a 10° arc as the basic angle for clockwise motion.
1 The arc resolution uses a 5° arc as the basic angle for clockwise motion.
2 The arc resolution uses a 10° arc as the basic angle for counterclockwise motion.
3 The arc resolution uses a 5° arc as the basic angle for counterclockwise motion.
The arc resolution uses a 1° arc as the basic angle for clockwise motion.
4
(FW V1.04.60 or later)
The arc resolution uses a 1° arc as the basic angle for counterclockwise motion.
5
(FW V1.04.60 or later)

Other
The arc resolution uses a 1° arc as the basic angle for clockwise motion.
_6
3. D1 and D2 are the pulse output devices for the X and Y axes respectively. Refer to DPPMR instruction (API 2710)
for the selection of output points and output mode for the axes.
the PLC plans the travel path for the arc after the instruction is executed. But if the calculation process which is
estimated cannot achieve the planned arc travel path, the output frequency is automatically decreased to fulfill the
synchronized arc drawing function.
5. When the X axis coordinate of the center point O=0, point O is defined as the point staying in QI of point A if Y axis
target coordinate >= 0. Whereas, if Y axis target coordinate < 0, point B is defined as the point staying in QIII of
point A.
6-940
The clockwise circle drawing:
Point A is the present position and point O is the target center, r is the radius of the circle as the figures below.
O O
r
A
Center O in QI and QIV Center O in QII and QIII
The counterclockwise circle drawing:
O O
r
6_
A
Center O in QI and QIV Center O in QII and QIII
6-941
Example
1. Taking (40000, 50000) as the center O and (10000, 10000) as point A, draw a circle as shown below.
O (4 0000, 50000)
O
A (10000, 10000)
A
2. Steps:
 The calculated relative coordinates of point O: (30000, 40000)
 The coordinates of point A is the present position; SR460=10000 and SR480=10000
 S3=1 and the clockwise circle drawing is performed with a 5° as the basic motion angle.
 When the PLC runs the program and M0 is set to ON, the relative-position circle drawing starts.
_6
3. Operation:
 When the PLC runs the program and M0 is ON, the PLC starts to draw the circle in the clockwise direction at 100
kHz.
 When the circle drawing completes, SM461 and SM481 are ON.
6-942
2717 D CCMA S1，S2，S3，S4，D1，D2 The absolute-position circle drawing

S1      
S2      
S3      
S4      
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4  
D1 
D2 

－－ AS
Symbol
S1 ： X axis coordinate of the center (absolute positioning) 6_

S2 ： Y axis coordinate of the center (absolute positioning)
S4 ： Target frequency
Explanation
1. S1 and S2 are respectively the X and Y axis coordinates of the center of a circle (absolute positioning). For more
information, refer to the DCCMR instruction (API 2716).
6-943
Example
1. Taking (40000, 50000) as the center O and (10000, 10000) as point A, draw a circle as shown below.
O (4 0000, 50000)
O
A (10000, 10000)
A
3. Steps:
 Set the absolute X coordinate and Y coordinate (40000, 50000) in the instruction
 Point A is the present position, SR460=10000 and SR480=10000
 S3 is 1 and the clockwise circle is drawn with 5° as the basic motion angle.
 When the PLC runs the program and M0 is ON, the absolute-position circle drawing starts.
_6
4. Operation:
 When the PLC runs the program and M0 is ON, the PLC starts to draw the circle in the clockwise direction at 100
kHz.
 When the circle drawing completes, SM461 and SM481 are ON.
6-944

Position planning table controls the
2718 TPO S，D1，D2
output

S    
D1 
D2   DWORD  
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S  
D1  
D2 

－ AS -
Symbol
S ： The first output number in the position planning table
D1 ： The output number that is being output
D2 ： Switch flag at the end of the consecutive-number output
6_
Explanation:
1. This instruction uses the position planning table to control the output. S is the number listed in the position planning
table. If the number does not exist in the table, the instruction is not executed, SM0 is ON and the error code is
SR0=16#2027.
2. S is the first output number when PLC runs. Refer to the value in D1 if there are consecutive-number outputs during
the output.
3. When one single number or the first one of consecutive numbers is output, the switch flag D2 is set to OFF. When
the consecutive-number output reaches the output number to be switched to, D2 is ON for a scan cycle and then is
ON again until the last number output is completed.
6-945
The example and timing diagram for the flag state switching are shown below.
M0
TPO
M0 EN D1 D100 D100 1 2 3
1 S D2 M100
M100
4. The switch flag D2 is affected by the PLC scan time. If the time for switching to the next output number is shorter
than the scan time, the flag for switching to the output number may not reset to OFF.
only once.
6. If using the function Single-axis multi-segment motion and the firmware is below V1.07.10, you cannot use the stop
flag during output. If you need to stop outputting, use this instruction instead.
7. For firmware V1.08.00 or later, you can use the stop flag during output to stop the output. If you use the stop flag
and this instruction, it will stop output after this segment is done outputting. For example, supposing the segments
are 1, 2 and 3 for output in a consecutive order and you use the stop flag while outputting segment 2. The system
will complete outputting segment 2 and then after you switch the stop flag to OFF, the execution of this instruction
will resume in the segment 3.
_6
8. If using the funciton Single-axis point-to-pint motion to output, and using the stop flag during the output, this
instruciton will stop execution and resume execution and output the remainings after the stop flag is OFF.
9. If using the fucntion 2-axis arc interpolation, and using the stop flag during the output, this instruciton will stop
execution after one basic unit of arc interpolation (1 degree) and this instruciotn resumes execution after the stop
flag is OFF, and output the remainings.
6-946
Example 1:
1. Enable the mechanical unit conversion function
2. Set the position planning table and download the parameters
The target position is 2000 (Unit:mm). After converting in the position planing table, 400,000 output pulses are
downloaded and saved in the PLC.
When M0 is ON, Y0.0 outputs 400,000 pulses at 100kHz. After the output completes, M100 is ON.
Example 2: Use global symbol or D device in Target Position
1. Use D device in Target Position of the position planning table and download the parameters. 6_
The unit for D60 in PLC is pulse by default. If you need to use D devices in Target position and in the
mechanical unit, you need to convert the mechanical unit to pulse.
2. When M0 is ON, and D60 is 400,000. Y0.0 outputs 400,000 pulses at 100kHz. After the output completes,
M100 is ON.
Note: the unit is pulse, when you use global symbols, D devices, or instructions including DTPWS, DTPWL,
and DTPWC to input values in in Target Postion.
6-947
3. If global symbols are used in Target Position
A. You need to assign an address for the global symbol.
B. Use global symbols in Target Position of the planning table.
Example 3: Use abort symbol and completion flag
1. Set up the positioning planning table as shown below.
2. Abort signal: When No. 3 stops the outputting abruptly, M100 is ON and the system starts to output No. 4
immediately.
The abort symbol is applicable for the following conditionss: external interrupts, high-speed comparision
_6 interrupts and M devices (M0~8191).
3. Completion flag: When No. 4 completes the outputting, M777 is ON. When the execution of this positioning
planning table is complete, the system calls for an interrupt or starts a M device.
You can use the interupt numbers I510~519 and M device (M0~M8191) in the positioning planning table.
Note: If you use interrupts instead of M devices, PLC scan cycle is not affected.
6-948
Example 4: Single-axis multi-segment motion
1. Set up the positioning planning table as shown below.
2. When M0 is ON, Y0.0 outputs No.1 to No. 3 consecutively. After the ouptput is done, M100 is ON.
1. Stop flag and immediately stop flag
a) The following graphic shows the output diagram based on example 4.
Ramp-down stop Immediately stop
6_
b) Ramp-down stop
 When M0 is ON, the TPO instruction is executed and starts to output No. 1 segment.
 When the stop flag SM463 is ON during the output of No.2 segment, the state of the immediately
 If the immediately stop flag SM476 is OFF, the output ramps down to stop, according to the SR465 ramp-
down time in axis 1, till the it drops to the lowest 1000 Hz frequency.
 Output at the lowest 100Hz freuency and till the No. 2 output is complete and stopped. (pulse = 600 K)
⑤ After the stop flag SM463 switches to OFF, the execution of TPO instruciton starts outputting No.3
segment till the output is complete. (pulse = 1200 K)
6-949
c) Immediatelly stop
 When M0 is ON, the TPO instruction is executed and starts to output No. 1 segment.
 When the stop flag SM463 is ON during the output of No.2 segment, the state of the immediately
 If the immediately stop flag SM476 is ON, the output stops after the No. 2 output is complete.
(pulse = 600 K).
 After the stop flag SM463 switches to OFF, the execution of TPO instruciton starts outputting No.3
segment till the output is complete. (pulse = 1200 K)
_6
6-950

Setting single-axis output
2719 D TPWS P S1，S2，S3 parameters in the position planning
table

S1    
S2    
S3    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  

AS - AS
Symbol
S1 ： A number listed in the position planning table
S2 ： Target position
S3 ： Target speed
Explanation 6_
1. This instruction sets the single-axis output parameters in the position planning table. S1 is the number listed in the
position planning table. If the number does not exist in the table, or the number is not under Single-axis point-to-
point motion, or under Single-axis multi-segment motion, the instruction is not executed, SM0 is ON and the error
code is SR0=16#2027.
2. S2 is the target position (must be a 32-bit integer). If you use the mechanical unit conversion when editing the
position planning table in ISPSoft, use the conversion instruction for modification first.
3. S3 is the target speed. The range is between 1–200,000Hz. Note: The maximum speed of the output axis Y0 and Y2
is 4 MHz for AS324MT.
4. When the instruction is executed to modify the parameters for the single axis which is outputting pulses, the modified
parameters are kept in the table and are not effective until the next output starts.
6-951
5. The parameters modified by the instruction can only be modified while the PLC is running. The last written
parameter is not saved when the power turns OFF. The table that you edit in ISPSoft and download to the PLC is
processed as the default position planning table when the power is ON.
6. This instruction does NOT modify the acceleration or deceleration time. If you need to modify the time for
acceleration or deceleration, you can set SM585 flag to ON, and the system refers to the acceleration and
deceleration time set in SR to change the acceleration time in single-axis point-to-point motion and single-axis multi-
segment motion or the deceleration time in single-axis point-to-point motion. Re-execute this instruction to actualize
this modification. This function is available for PLC with FW V1.06.00.
Example 1: Change the parameters of Axis 3 of Number 5 during execution in Single-axis point-to-point motion.
1) Use DMOV instruction to define new target position and target speed.
2) Use MOV instruction to define the start/end frequency in SR503, acceleration time in SR504 and deceleration
time in SR505 for Axis 3. After that the relative parameters in single-axis point-to-point motion are updated.
3) Set the flag SM585 to ON.
4) Re-execute DTPWS instruciton to actualize the modification.
_6 5) After that, SM585 switches to OFF automatically.
Example 2: Change the parameters of Axis 3 of Number 2 during execution in Single-axis multi-segment motion.
1) Use DMOV instruction to define new target position and target speed.
2) Use MOV instruction to define the acceleration time in SR504. After that the relative parameters in single-axis
multi-segment motion are updated.
3) Set the flag SM585 to ON.
4) Re-execute DTPWS instruciton to actualize the modification.
5) After that, SM585 switches to OFF automatically.
6-952

Setting linear interpolation
2720 D TPWL P S1，S2，S3，S4 parameters in the position planning
table

S1    
S2    
S3    
S4    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4  

AS - AS
Symbol
S2 ： Target position of the X axis

6_
S3 ： Target position of the Y axis
S4 ： Target speed
Explanation
1. This instruction sets the 2-axis linear interpolation parameters in the position planning table. S1 is the number listed
in the position planning table. If the number does not exist in the table or the output of the number does not belong
to the 2-axis linear interpolation, the instruction is not executed, SM0 is ON and the error code is SR0=16#2027.
2. S2 and S3 are respectively the target positions of the X and Y axes, which can only be 32-bit integers. If you use the
mechanical unit conversion when editing the position planning table in ISPSoft, use the conversion instruction for
modification first.
6-953
3. S4 is the target speed. The range is between 1–200,000Hz.
4. When the instruction executes the linear interpolation, the target frequency S4 automatically corresponds to the
output of the axis which is farthest from its target position. If X axis and Y axis cannot simultaneous reach the target
positions, the PLC automatically decelerates the frequency to make the two axes reach the target positions
simultaneously.
5. When the instruction is executed to modify parameters for the two axes (either of which is outputting), the modified
parameters of the two axes are kept in the table and are not effective until the next 2-axis output starts.
6. The parameters modified by the instruction can be modified only while the PLC is running. The last written
parameter is not saved when the power turns OFF. The table that you edit in ISPSoft and download to the PLC is
_6
6-954

Setting arc interpolation parameters
2721 D TPWC P S1，S2，S3，S4，S5
in the position planning table

S1    
S2    
S3    
S4    
S5    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4  
S5  

AS - AS
Symbol

6_
S2 ： X axis target position
S3 ： Y axis target position
S4 ： The shift of the center
S5 ： Target speed
Explanation
1. This instruction sets the 2-axis arc interpolation parameters in the position planning table. S1 is the number listed in
the position planning table. If the number does not exist in the table, or the output of the number does not belong to
the 2-axis arc interpolation, the instruction is not executed, SM0 is ON and the error code is SR0=16#2027.
6-955
2. S2 and S3 are respectively the target positon on the X and Y axes. S4 is the distance to shift the center. The three
parameters can only be 32-bit integers. If you use the mechanical unit conversion when editing the position planning
table in ISPSoft, use the conversion instruction for modification first.
3. S5 is the target speed. The range is between 1–200,000 Hz. It is the reference speed for the actual output. The PLC
automatically decelerates the speed if the 2-axis synchronized output cannot be achieved.
4. When the instruction is executed to modify parameters for the two axes (either of which is outputting), the modified
parameters of the two axes are kept in the table and are not effective until the next 2-axis output starts.
5. The parameters modified by the instruction can be modified only while the PLC is running. The last written
parameter is not saved when the power turns OFF. The table that you edit in ISPSoft and downloaded to the PLC is
This instruction does not support changing the clockwise or counterclockwise motion direction. For direction change, add
_6
or modify the output parameters for arc interpolation in the position planning table in ISPSoft.
6-956
2723 D PPGB S1，S2，S3，S4，D1，D2 Point-to-point go back and forth

S1 
S2 
S3 
S4 
D1 
D2 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2  
S3  
S4 
D1 
D2 

－ - AS
6_
Symbol
S1 ： Relative target position A
S2 ： Relative target position B
S3 ： Target speed
Target speed ratio adjusted value
S4 ：
(floating point value)
D2 ： Target speed can change indicator
Explanation
1. This high speed output instruction specifies a movement going back and forth between two target positions that are
converted from the two relative target positions specified by S1 and S2. This instruction is applicable for machines
such as warping machines in the textile industry, and winding & binding machines in the cable industry.
2. When the instruction starts the output, the relative positions S1 and S2 must be specified first so that the instruction
can make the calculation for switching to the next output. After the instruction is executed, you can modify the
target positions to execute, but you cannot change the outputting target positions.
6-957
 DPPGB instruction is executed. When S1 is 30,000 and S2 is -30,000, the motion goes toward the target position
A1=30,000.
 If the pulse position>15,000, the relative positions are modified into S1:20,000 and S2:-20,000, and the target
position is momentarily A1=30,000. The target positions obtained through calculation are B1=10,000(A1+ S2) and
A2=30,000(B1+ S1), since the outputting target positions cannot be modified.
3. S3 is the target speed (must be a 32-bit integer), and S4 is the target speed ratio adjusted value (must be a floating
point number). The actual speed is the result of multiplying the values in S3 and S4 and then rounding down the
calculation result to a 32-bit integer. The acceptable input speed range is 1–200 kHz. When values are out of
_6
range, the PLC automatically processes the value as the minimum or the maximum of the operation range. The
ratio formula for the actual target speed is S3 x S4. For instance, if target speed is 1 kHz, the adjusted floating point
is 1.2345 and the actual value is 1234 Hz.
4. When the instruction is outputting, the target speed and the adjusted ratio can be modified, and the result is
updated to the actual output speed once the instruction is scanned. But it is suggested that you do not change the
target speed too much in case the calculated deceleration is affected.
5. The output points for D1 can only be Y0.0, Y0.2, Y0.4, Y0.6, Y0.8 and Y0.10, and it occupies 2 consecutive output
points. The output sets and the output special register modes are listed in the following table.
Output axis number 1 2 3 4 5 6
D1+0 output points Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10
D1+1 output points Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
Output modes SR462 SR482 SR502 SR522 SR542 SR562
6. D2 is the flag indicating the target speed and the adjusted ratio that you can change. When this flag is ON, the
executing target speed can be modified. When the flag switches from ON to OFF, it is now decelerating and the
current target speed will be processes as the target speed for the next output.
6-958
7. There is no limit on the number of times you can execute this instruction, but during execution, the designated high
speed axis cannot be occupied by any other instruction, and the other instruction is not executed.
The following graphic shows the output timing diagram.
Speed
D2 = OFF
D2 = ON
S3 x S4
D1 +1 = OFF
S1
S2 Position
D1 +1 = ON
S3 x S4
D2 = ON
D2 = OFF
Example
When M0 is ON, the DPPGB instruction starts to move back and forth between the target positions that are calculated
6_
from the two relative target positions specified by S1 and S2, at the actual target speed of 8500 Hz (5000*1.7). Y0.0 is the
output point. Y0.1=OFF means the positive direction.
6-959
_6
6-960
Explanation
1. After the instruction starts the output, modify the relative target positions A for S1 and B for S2.
a) The Y0.0 output graph:
b) Explanation:
 When S1:30,000, S2:-30,000 and M0 enables the DPPGB instruction, the motion goes toward the position
A1=30,000.
 When D0=1 and the position: number of pulses in SR460 >15,000, the relative positions are changed to
S1:26,000 and S2:-28,000.
At the moment, the target position is A1=30,000 since the outputting target position cannot be modified. The
calculated target positions are B1=2,000(A1-28,000), A2=28,000(B1+26,000). 6_
 When D0=2 and the position: number of pulses in SR460 >15,000, the relative positions are changed to
S1:22,000 and S2:-24,000.
At this time, the target position is A2=28,000 since the outputting target position cannot be modified.
The calculated target positions are B2=4,000(A2-24,000), A3=26,000(B2+22,000).
 When D0=3 and the position: number of pulses in SR460 >15,000, the relative positions are changed to
S1:18,000 and S2:-20,000.
The calculated target positions are B3=6,000(A3-20,000)，A4=24,000(B3+18,000).
 When D0=4 and the position: number of pulses in SR460 >15,000, the relative positions are changed to
S1:30,000 and S2:-24,000.
The calculated target positions are B4=0(A4-24,000) and A1=30,000(B4+30,000).
6-961
Step S1: Relative position S2: Relative position Target position B Target position A
 30,000 -30,000 - A1=30,000
 26,000 -28,000 B1=2,000 A2=28,000
 22,000 -24,000 B2=4,000 A3=26,000
 18,000 -20,000 B3=6,000 A4=24,000
 30,000 -24,000 B4=0 A1=30,000
_6
6-962

Zero return 2
2724 D ZRN2 TFreq, JFreq, Mode, DOG, NL, Pulse, Dir
(directional output can be defined)

TFreq      
JFreq      
Mode      
DOG  
NL  
Pulse 
Dir  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
TFreq  
JFreq  
Mode  
DOG 
NL 
Pulse 
Dir 

－－ AS
6_
Symbol
TFreq ： Target frequency for zero return
JFreq ： JOG frequency for DOG
Mode ： Zero return mode
DOG ： Input device for DOG
NL ： Input device for Negative Limit point
Pulse ： Pulse output device
Dir ： Output direction device
6-963
Explanation
1. This instruction is available for PLC with FW V1.04.90 (V1.04.90 included) or later.
2. This instruction causes the machine to return to the zero point. The range of the target frequency (TFreq) for zero
return is between 1 Hz–200 kHz. The JOG frequency (JFreq) should be less than the target frequency (TFreq).
The JOG frequency (JFreq) is the start frequency. If the target frequency (TFreq) is less than (JFreq), the target
frequency (TFreq) is automatically revised processed as equal to (JFreq).
3. Do not change the operands DOG, NL, Pulse, or Dir during instruction execution. The input point for DOG and NL
is suggested to use the 16 high-speed input points X0.0–X0.15. They will not be affected by PLC instruction scan
time. If you use X1.0 successive input points or M devices, they will be affected by the PLC instruction scan time.
4. See the below descriptions for DOG, NL and Dir.
You can use X or M device but do NOT choose the same input point for different axis.
DOG point When the DOG point uses X0.0–X0.15 for inputs, go to HWCONFIG to set up the
filtering time for the inputs if the switch starts to rattle.
NL point You can use X or M device but do NOT choose the same input point for different axis.
Dir contact You can use Y or M device but do NOT choose the same input point for different axis.
5. See the below SR and SM table for pulse outputting.
Pulse output points Y0.0 Y0.2 Y0.4 Y0.6 Y0.8 Y0.10

_6
Setting up the time for
directional outputting
SR640 SR642 SR644 SR646 SR648 SR650
goes first before pulse
outputting (unit: 1 ms)
Pulse output points Y0.1 Y0.3 Y0.5 Y0.7 Y0.9 Y0.11
Setting up the time for
directional outputting
SR641 SR643 SR645 SR647 SR649 SR651
goes first before pulse
outputting (unit: 1 ms)
6-964
SR474 SR494 SR514 SR534 SR554 SR574

SR475 SR495 SR515 SR535 SR555 SR575
6. Select the zero return mode. The function code is set by the two high and low16-bit parameters. See the following
table for details.
Select the zero return mode

High 16-bit Low 16-bit
b31~b16 b15~b6 b5 b4 b3~b0
Setting NL signal Setting DOG signal Mode settig

Number of pulses
reserved 0: contact A 0: contact A 0~2;
for motion
1: contact B 1: contact B 8~10
7. The function code is set by the two high and low 16-bit parameters. See the following table for details.
Code
Functions High Low 16- Description
16-bit bit
When the instruction is executed, the search for the
zero point is in the negative direction with the target
Leaves the zero point in frequency. When the zero point is ON (the zero
the negative direction point signal changes from OFF to ON), the
and then stops
0 0
frequency is decreased to the JOG speed and the 6_
(Mode 0) motion in the negative direction continues, and
does not stop until the zero point signal changes
from ON to OFF.
the positive direction and zero point signal changes from OFF to ON), the
0 1
then stops frequency decreases to 0 immediately, and then
(Mode 1) the motion is in the positive direction at the JOG
speed, and does not stop until the zero point
Returning to the zero point is the same as that for
the low 16-bit code. After the zero point is ON, the
Mode 0 Moves again Number of motion continues according to the number of
after returning to the zero pulses for 2 specified pulses. When the high 16-bit code is a
point motion positive number, the search is in the positive
direction. A negative value means that the search
is in the negative direction.
Leaves the zero point in
8+0=8
the positive direction and Refer to mode 1. The operation for zero point
0 8+1=9
then stops return is the same as that for code 1 (mode 1).
(bit3=ON)
(Mode 1)
Mode 1 outputs the Number of 8+2=10 The operation for zero point return is the same as
6-965
Code
Functions High Low 16- Description
16-bit bit
number of pulses after pulses for (bit3=ON) that for low 16-bit code 1.
returning to the zero motion After returning to the zero point, the motion
point continues in accordance with the number of
specified pulses. When the value of the high 16-bit
code is a positive number, the motion is in the
positive direction. A negative number indicates
that the motion is in the negative direction.
When in the low 16-bit code, bit 4 is ON, it means
+16 the zero point is ON as the DOG point changes
DOG point is B point
(bit4=ON) from ON to OFF and the zero point is left as the
DOG point changes from OFF to ON.
When in the low 16-bit code, bit 5 is ON, it means
+32 the zero point is ON as the NL point changes from
NL point is B point
(bit5=ON) ON to OFF and the zero point is left as the DOG
point changes from OFF to ON.
8. The execution sequence is based on the value of the low 16-bit code in the table above, and described below.
The direction of DOG signal is determined by the value of bit 5.
 The NL negative limit and DOG signal are determined by the value of bit 5 and bit 4.
 Mode 0 or mode 1 for the zero point return, selected according to the value of bit 3.
 The operation of the zero point return is performed according to the values of bit 1 and bit 0.
_6
9. The Completion flag is set to ON after the instruction finishes performing the specified function. For example, for
function code 2, the PLC sets the Completion flag to ON only when the number of specified pulses completes
outputting.
10. After the DZRN2 instruction is executed, an interrupt service program is not executed till the DZRN2 instruction is
disabled, if the specified input point for the zero point is the same as that for the external input interrupt in the
program.
only once.
6-966
The steps for performing the functions are as below
Function code 0:
 The DZRN2 function is executed and the search for the zero point is in the negative direction with the target
frequency (TFreq).
 After the DOG signal is received, the output frequency decreases to the JOG frequency (JFreq). The output
continues in the negative direction and does not stop until the zero point signal changes from ON to OFF.
 The output stops when the signal changes from ON to OFF and the axis moves away from the DOG signal.
Negative direction
Completion flag ON
DOG signal ON
Frequen cy
Target frequency
JOG frequency
Time
1 2 3
Function code 1:
6_
frequency (TFreq).
 After the DOG signal is received, the output is in the positive direction with the JOG frequency (JFreq) after the
output frequency decreases, and the motion direction reverses. The output does not stop until the zero point
 The axis moves away from the DOG signal and PLC stops when the signal changes from ON to OFF.
P ositive
Negative direction direction
Completion flag ON
DOG signal ON
F requency
Target frequency
JOG frequency
Time
1 2 3 4
6-967
Function code 2:
frequency (TFreq).
 After the DOG signal is received, the output decreases the frequency to the JOG frequency (JFreq) and
continues in the negative direction.
 When the DOG signal is left and the signal changes from ON to OFF, the specified number of pulses are output.
 The first pulse output starts.
 When the 100th pulse output completes, the PLC stops and the Completion flag is ON.
Completion flag ON
DOG signal ON
Output Y
Frequency
Target frequency
JOG frequency
Time
_6 1 2 3 4 5
Example
direction. When the DOG signal is received and X0.4 is ON, it keeps moving in the negative directon with the JOG
frequency of 1 kHz. The output stops immediately after X0.4 changes from ON to OFF.
6-968
Explanation
Mode is set to 0.
High 16-bit [0000] is to disable the function to move a number of pulses..
Low 16-bit [0000] is Mode 0; when the DOG signal is received, the axis moves in the negative direction; after the axis
moves away from the DOG signal, it stops immediately.
6_
6-969
6.27 Delta CANopen Communication Instructions
6.27.1 List of CANopen Communication Instructions

The following table lists the High-speed Output instructions covered in this section.
Instruction code Pulse Delta specific

API Function
16-bit 32-bit instruction Servo Inverter
Initializing the servo for CANopen

2800 INITC – – V V
communication
2801 ASDON – – Servo-ON and Servo-OFF V V
Setting the acceleration time and deceleration

2802 CASD – – V V
time for a servo
2803 – DDRVIC – Servo relative position control V –
2804 – DDRVAC – Servo absolute position control V –
2805 – DPLSVC – Servo speed control V V
2806 ZRNC DZRNC – Servo homing V –
Reading and writing CANopen communication

2807 COPRW – – V V
data
2808 COPWL DCOPWL – Writing multiple CANopen parameter values V V
_6 2809 RSTD – – Sending Reset or NMT command V V
2810 ZRNM – – Setting the homing mode for Delta servo V –
2811 EMER – – Reading Emergency message V V
Controlling the tracking function of a servo via

2812 – DCSFOC – V –
communication
2813 ECAMD – – Downloading E-CAM chart to the Slave V –
2814 – DECAMS – E-CAM parameter setting and planning V –
Activating E-CAM control and displaying the

2815 ECAMA – – V –
status
Modifying the starting address for E-CAM chart

2816 ECAMC – – V –
and the E-CAM chart length in the servo
2817 – DTQC – Torque control V V

2818 – DTQLC – Speed of torque control V V
6-970
6.27.2 Explanation of CANopen Communication Instructions
Initializing the servo for

2800 INITC S
CANopen communication

S DWORD  
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S 

－ AS －
Symbol
S: Number of station to be initialized
Explanation
1. Before executing the instruction, if the PLC CPU is AS300, be sure to select Delta Special Driver & AS Remote 6_
Mode as the working mode for function card 2 in the hardware configuration software (HWCONFIG) in ISPSoft. If
the PLC CPU is AS200 or AS100, make sure the working mode for the built-in CAN communication port is selected
to Delta Serve Drives in HWCONFIG.
2. The servo range of S is 1–8. When the input value is greater than 8, PLC will automatically process 8 as the value
of S for the initialization. The station address must start at 1 and the following addresses cannot be skipped or
reserved.
3. When the PLC firmware is V1.02.00 or later, S ranging from 21 to 28 is added for inverters. For the input value that
is not in the range of 21 to 28, this instruction will not be executed. Same rule applies to the servo; the station
address must start at 21 and the following address should be in consecutive order.
4. When setting the number of station to be initialized to 5, this instruction initializes station address from 1 to 5. And
when setting the number of station to be initialized to 23, this instruction initializes station address from 21 to 23.
When there are 5 servo systems and 3 inverters that need to be initialized, you need to execute this instruction
twice. One is INITC 5 for 5 servo systems and the other is INITC 23 for 3 inverters.
5. When you execute this instruction (SM1686 = OFF) on servos (S is 1–8), SM1681 is set to OFF and the states of
6-971
servo 1 to 8 are reset to uninitialized. SM1681 is set to ON when the initializations on servo 1 to 8 are complete.
SM1683 is set to OFF and S is 21–28, the states of servo 21 to 28 are reset to uninitialized. SM1683 is set to ON
when the initializations on servo 21 to 28 are complete.
Note: The initialization flags are used for notifying if the initialization is done or not. After that if you use parameters
in this instruction, these two flags are used as completion flags for the execution of the instruction.
6. SM1682 is set to ON when an error occurs during communication. In addition, SR658 retains the number of the
axis in which the error occurs and SR659 retains the error code. (The flag and code here are especially for Delta
CANOpen Communication Instructions.)
7. For firmware V1.06.40 or later, a new functional SM1686 is added for initializing only one specified slave. For
example if you set SM1686 to OFF and execute INITC 3 indicates the slaves 1, 2 and 3 will be initialized. After that
if you set SM1686 to ON, execute INITC 6 indicates only the slave 6 will be initialized. And then together you will
have slaves 1, 2, 3, and 6 initialized.
Note: if you need to initialize multiple slaves and single slave, you need to set SM1686 to OFF first to have multiple
slaves initialized and then set SM1686 to ON for single initializations, but not the other way around.
8. If a heartbeat error (SR0 = 0x1900~0x191C; last 2 codes are the slave ID) occurs after the initialization is complete
and the SM1684 is OFF (default, indicating when one goes down, all the servos are OFF), the initialization
complete flags SM1681 & SM1683 will be cleared to OFF and related actions on other slaves will also be paused.
After all the troubles are cleared, you need to initialize every slave to restart the operation. PLC will turn the error
LED off after PLC confirms the initialization is complete. This error will be recorded in the error log.
_6
9. If the axes are working independently and the communication is working properly, you can set the SM1684 to ON
(indicating when one goes down, only the defective servo is OFF) to notify PLC to record the specific error on the
error log and other slaves can keep working.
10. You need to set the communication station and speed of the servos manually and then turn the servos off and then
on again to activate the new parameters.
11. This instruction should not be used in the Structured Texts programming language, or interrupt programs or FB
programs that only be called once.
6-972
Initialization and operation process chart
In se r t AS - FCO P M
P ower O n
HW CO NF IG
Sel ect Delta S peci al Dr iver & AS Re mote Mode
FC OP M Mo d e
PLC Run
PL C se nd i n g
in i ti al i za ti on
No
Initi ali zatio n Set up error record
compl ete ex : Servo, V FD dis connected
Set up ini tial ization c omplete P LC Ru n

flags M1681 & M1683
Clear initializ ati on complete Wa i t fo r
flags M1681 & M1683 t he P L C to ru n
PL CS top
De termi ne i f th e he artbe at Abn ormal
works n o rmal ly Stop heartbeat f unc ti on
and s top s ervo & V F D
Nor ma l
S till R un Exec ute the communic ati on PLC S top C lear initi alization complete
ins truc ti ons for positioning fl ags M1681 & M1683
Example of Communication with Delta servo ASD-A2M
1. Before using the Delta CANopen instruction, mount an AS-FCOPM card in the AS Series PLC (slot 2 only) and be
sure to select Delta Special Driver & AS Remote Mode as the working mode for the AS-FCOPM card 2 in the 6_
configuration software (HWCONFIG in ISPSoft). Set the baud rate to 125 kbps, 250 kbps, 500 kbps, or 1000 kbps.
Figure 1 Function card 2 setting
6-973
Figure 2 Working mode selection
2. Connect the AS Series PLC to an ASDA series with a CANopen communication cable as shown in the figure
below. (Switch the 120 Ω terminal resistor ON in the AS-FCOPM card to enable the terminal resistor.)
_6
3. Follow the steps below for the basic settings on the panel of the ASD-A2.
a. Set the servo parameter P2-08 to 10 to restore the factory settings.
b. Power the servo off and back on again.
c. Set P1-01 to 0001 (PR mode).
d. Set P3-01 to 0400 and the baud rate of the servo for CANopen communication to 1.0 Mbps. The baud rate must
be the same as that of the PLC.
e. Set a station address for every servo, based on the number of servos. Set P3-00 of each servo to 1, 2, and 3 in
order. You can set a maximum of eight servos.
f. Power the servo off and back on again.
g. Begin operation after the basic setting is complete.
6-974
4. Download the sample program and set M0 to ON (default: SM1686 = OFF). The instruction initializes the servos at
station addresses 1–3. When SM1681 is ON, the initialization is complete. When the servo enters CANopen mode
successfully, Co-Ld information is displayed.
Ladder diagram:
Structured Texts programming language:
5. The following list shows the settings to initialize a servo drive in the AS Series.
A. Set P2-30 (auxiliary function) to 5 to indicate that the servo does not need to store the settings in EEPROM
permanently. This can prolong the servo life span.

6_
B. Reset P6-02 (PATH#1) to 0 and P6-06 (PATH#3) to 0. This indicates that PATH#1 & #3 in PR mode are both
cleared.
C. Set P3-06 (SDI source) to 16#0100. This indicates that DI1–DI8 are controlled by the hardware, EDI9 is
controlled by the software, and EDI10–EDI14 are controlled by the hardware.
D. Reset P4-07 (SDI status controlled manually) to 0.
E. Set P2-36 (EDI9) to 16#0101. This indicates that the function of EDI9 is set to Servo ON.
F. Set P0-17 (CM1A) to 1. This indicates that the mapping parameter is the pulse command output register
CMD_O.
G. Set P0-18 (CM2A) to 64. This indicates that the mapping parameter is the pulse command register CMD_E.
H. Set P5-20–P5-35 (acceleration time) to 1. This indicates that the acceleration time is 1 ms.
I. Set P5-60–P5-75 (target speed) to 1. This indicates that the target speed is 0.1 rpm.
J. Set PDO1 to correspond to P5-07 (PR command), P0-01 (Fault code), P0-46 (state of DO point) and P4-07
(state of DI point)
6-975
K. Set PDO2 to correspond to P0-09 (CM1 state: CMD_O) and P0-10 (CM2 state: CMD_E).
L. Set PDO3 to correspond to P0-11 (CM3 state: state of current torque)
M. Available for PLC with FW V1.04.00 or later: set time for the heartbeat and the PLC scan overtime to 200ms
(default). When a communication overtime occurs, PLC will send error message (error LED flashing slowly; refer
to error code for more details) and the servo turns off automatically.
N. If SM1685 is ON, PDO3 reads self-defined parameters from servo drive P0-12 and stores the data in SR791-
SR806. You need to set up the P0-20 (CM4A) before executing. 2 SRs are reserved for every servo drive axis
and you can define their data types.
Note: PLC with firmware V1.04.10 or later supports states of current torque (PD03) and DI point (PD01). PLC with
firmware V.104.60 or later supports reading self-defined parameters (PD03)
6. Do not use the COPRW instruction (API 2807) to modify the servo parameters of the eight items A, B, F, G, J, K
and N above after initialization.
7. When you use an absolute-type servo, use the COPRW communication instruction to write 16#0100 to P3-12,
which writes the relevant absolute-type servo parameters to EEPROM at the moment the servo powers off.
8. Set the relevant DI signal configuration parameters manually or with the COPRW instruction to modify the
hardware DI signal setting of ASD-A2. Use COPRW to modify the configuration after execution of the INITC
instruction is complete and before the servo is enabled.

_6
9. When the initialization is complete, the servo is in the PR mode. Do not make any communication control on servo
P5-18.
10. For more details on the servo parameters, refer to the Delta Servo Operation manual.
Example of Communication with Delta Inverter
1. Manually set the inverter parameter P09-36 (ranging from 21 to 28), P09-37 (communication baud rate default is
1MHz) and P09-40 to standard CANopen protocol (default).
2. Manually set the source of frequency command P00-20 to 6 and source of the operation command P00-21 to 3,
and have them controlled by CANopen communication.
3. The following list shows the settings to initialize an inverter in the AS Series.
A. Set PDO mapping area: the operation frequencies, current state, and states of torque and DI point correspond
to PLC SRs.
B. Set time for the heartbeat and the PLC scan overtime to 200ms (default). When a communication overtime
6-976
occurs, PLC will send error message (error LED flashing slowly; refer to error code for more details) and the
servo turns off automatically.
4. For more details on the servo parameters, refer to the Delta Inverter Operation manual.
Example
1. When M0 changes from OFF to ON, the INITC instruction starts to initialize the inverter at station address 21, until
SM1683 is ON. When SM1683 is ON, it indicates the initialization is complete.
Additional Remarks:
The following table shows special flags (SM) and registers (SR) related to initialization.
Flag R/W ID. 1 ID. 2 ID. 3 ID. 4 ID. 5 ID. 6 ID. 7 ID. 8
Enable specific function R/W The flag in HWCONFIG is set to ON when the PLC is from Stop to Run.
6_
Initialization and communication
R SM1681
complete (INITC and CASD)
CANopen communication error R SM1682
Single slave initialization SM1686 = OFF (default; multiple slaves initialization)

R/W
(for firmware V1.06.40 or later) SM1686 = ON (single slave initialization)
Number of the axis with a

R SR658
communication error
Communication error code R SR659
Note1: After the axis starts to output, PLC clears the corresponding completion flag.
The following table shows the Delta special drier CANopen error codes. (error code in SR659)
Error Code Cause
0x0002 The slave does not respond to the SDO message.

An error occurs in the message received by the slave. This error often occurs when the settings of the
0x0003 COPRW instruction are invalid causing the slave not to receive the complete message.
0x0004 The slave PDO message is not received.
0x0005 An error occurs while using the instruction operand.
6-977
0x0006 One of the stations is being used when the INITC instruction is executed.
0x0007 Slave station address exceeds acceptable range of the instruction INITC
A slave cannot be reset; check if the communication cable is connected and if the communication of the
0x0008 slave is working properly.
When you use Delta Special Driver & AS Remote mode / Delta Special Driver & CANopen DS301 and execute INITC
instruction, the refreshing time of PDO data exchange among stations 1 to 15 and 21 to 28 is shown below. For example,
when the baud rate is 1M, PDO data exchange refreshing time is 10 ms X 5 times = 50 ms.
Baud rate (bps) 1M 500K 250K 125K 50K
Preset time to synchronize (ms)#1 10 15 30 60 80
Preset number of synchronization times #2 5 5 5 5 5
#1: If you use Delta Special Driver & CANopen DS301 mode, you can use CANopen Builder software to edit the time to
synchronize for the slaves. But the edited time can only be greater than the time shown in the table above. If you set the
time lesser than the time shown above, the system ignores the editing and runs according to the time shown above.
#2: If you use Delta Special Driver & CANopen DS301 mode, you can use CANopen Builder software to edit the number
of synchronization times for the preset number of synchronization times in the table of DS301. For the preset number of
synchronization times, it is not editable.
When you use Delta Special Driver & AS Remote mode / Delta Special Driver & CANopen DS301 and execute
_6 COPPRW instruction (SDO communication), the communication timeout is shown below.
Communication timeout (ms)#1 100 100 200 400 500
When the mode is CANopen DS301, you can set the time of the COPRW timeout in the CANopen communication setting
option from HWCONFIG; default timeout is 100 ms.
6-978
2801 ASDON S1，S2 Servo-ON and Servo-OFF

S1          
S2  
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  

－ AS －
Symbol
S2 ： Servo ON and Servo OFF
Explanation 6_
1. This instruction changes the state of the servo at the address in S1. The INITC instruction must be complete before
this instruction is executed.
2. The range of S1 is 1–8 (for servo) and 21-28 (for inverter). There will be no execution when the input value is out of
the range.
3. The range of S1 is 1–8 (for servo) and S2 is a non-zero value, the servo is enabled (Servo-ON). If S2 is 0, the servo
is disabled (Servo-OFF).
4. The range of S1 is 21–28 (for inverter). When S2 is 1, it indicates it is in inverter speed mode. When S2 is 2, it
indicates it is in inverter torque mode. When S2 is 0, it indicates it stops operating. Since control modes (speed mode
and torque mode) for inverters can be switched directly, the operation can keep going. Before switching control
modes, make sure all the inverter parameters are set.
6-979
5. Table of the last 2 points:
Drive type Range of S1 Descriptions of S2

1 = SERVO-ON
Servo 1-8
0 = SERVO-OFF
0 = stop operating
Inverter 21-28 1 = Speed mode
2 = Torque mode
6. Every servo (1-8) has a flag (SM1651–M1658) for displaying its state. You can read the actual servo state from the
flag. When the flag is ON, the servo is Servo-ON. When the flag is OFF, the servo is Servo-OFF.
7. Every inverter (21-28) has a flag (SM1621–M1628) for displaying its state. You can read the actual inverter state
from the flag. When the flag is ON, the inverter is ON. When the flag is OFF, the inverter is OFF.
8. SM1682 is ON if an error occurs during communication. In addition, SR658 retains the number of the axis in which
the error occurs and SR659 retains the error code.
Example 1 (Ladder diagram):
1. When M0 changes from OFF to ON, the INITC instruction starts to initialize the servos at station addresses 1–3,
until SM1681 is ON.
2. When M1 changes from OFF to ON, the ASDON instruction starts to enable the servo at station address 2. When
_6 SM1652 is ON, it indicates Servo-ON.
3. When M2 changes from OFF to ON, the ASDON instruction starts to disable the servo at station address 2. When
SM1652 is OFF, it indicates Servo-OFF.
6-980
Example 2 (Structured Texts programming language):
6_
1. When M1 changes from OFF to ON, this instruction starts to enable the servo at station address 2. When SM1652 is
ON, it indicates Servo-ON.
2. Make sure M1 and SM1652 are both ON and then set the auto return communication control right flag SM1582 to
ON for station address 2. This will free the communication control right and the station address 2 can receive and
execute other communication instructions.
3. When M2 changes from OFF to ON, this instruction starts to disable the servo at station address 2. When SM1652
is OFF, it indicates Servo-OFF.
4. Make sure M2 is ON and SM1652 is OFF and then set the auto return communication control right flag SM1582 to
6-981
Example 3 (communication with Delta inverters):
1. When M0 changes from OFF to ON, this instruction starts to initialize the station address 21. When SM1683 is ON, it
indicates the initialization is complete.
2. When M2 changes from OFF to ON, this instruction starts to set the control mode at the station address 21. When
SM1621 is ON, it indicates the inverter is in operation.
_6
6-982
Setting the acceleration time and

2802 CASD S1 , S2 , S3
deceleration time for a servo

S1          
S2          
S3   DWORD        
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  

－ AS －
Symbol
S2 ： Acceleration time (ms)
S3 ： Deceleration time (ms)

6_
Explanation
1. This instruction sets the servo acceleration and deceleration time for the servo at the address in S1. The INITC
instruction must be complete before this instruction is executed.
the range.
3. Table to describe S2 and S3
Drive type Range of S1 Range of S2 and Descriptions of S2 and S3

S3
S2: Acceleration time is the period of time during which
the servo spins up from 0 to 3000.0 rpm.

Servo 1-8 1-32767 (ms) S3: Deceleration time is the period of time during which
the servo spins down from 3000.0 rpm to 0.
Inverter 21-28 100-32700 (ms) S2: Acceleration time is the period of time during which
6-983
The input value the inverter spins up from 0.0Hz to the highest operation
should be multiplied
by 100. frequency.
S3: Deceleration time is the period of time during which
the servo spins down from the highest operation
frequency to 0.
4. When you execute this instruction and the range of S1 is 1–8 (for servo), SM1681 is set to OFF (parameters are
being editing). When the servo responds to the received command, SM1681 is ON (parameters are set
successfully). When you execute this instruction and the range of S1 is 21–28 (for inverter), SM1683 is set to OFF
(parameters are being editing). When the inverter responds to the received command, SM1683 is ON (parameters
are set successfully).
5. SM1682 is set to ON when an error occurs during communication. In addition, SR658 retains the number of the axis
in which the error occurs and SR659 retains the error code.
Example 1 (communication with Delta ASD-A2M)
1. When M0 changes from OFF to ON, the INITC instruction initializes the servos at station addresses 1–3, until
SM1681 is ON.
2. When M1 changes from OFF to ON and the target speed of the servo at station address 2 is 3000 rpm, the CASD
instruction sets the acceleration time of servo 2 to 3000 ms and the deceleration time to 9000 ms.
_6 3. If the target speed of servo 2 is 1000 rpm, the acceleration time and deceleration time are shown below.
Acceleration time: [3000 ms / 3000 rpm] × 1000 rpm = 1000 ms
Deceleration time: [9000 ms / 3000 rpm] × 1000 rpm = 3000 ms
6-984
Example 2 (communication with Delta inverters)
2. When M1 changes from OFF to ON, this instruction starts to set the acceleration time to 2000 ms and deceleration
time to 3000 ms at the station address 21.
6_
6-985
2803 D DRVIC S1, S2, S3 Servo relative position control

S1   
S2    
S3    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  

－－ AS
Symbol
S1 ： Station address of servo
S2 ： Relative target position
S3 ： Target speed
_6
Explanation
1. This instruction executes the servo relative position control for the servo at the address specified in S1. The INITC
and ASDON (servo ON) instructions must be complete before this instruction is executed.
2. The range of S1 is 1–8. There will be no execution when the input value is out of the range.
3. The range of S2 is -2147483648 to +2147483647. The +/- sign indicates the forward / reverse direction. The target
position is a relative position.
4. The unit of the value of S3 is 0.1 rpm. The range is 1–60000, which indicates 0.1–6000.0 rpm.
5. When the target position is reached, the corresponding completion flags of axes SM1631–SM1638 are ON. After the
axis starts to output, PLC clears the corresponding completion flag.
6. Refer to the following table for the corresponding SM and SR of the axes.
7. SM1682 is ON when an error occurs during communication. In addition, SR658 retains the number of the axis in
which the error occurs and SR659 retains the error code.
6-986
8. This instruction uses SDO (Service Data Object) of CANopen protocol to communicate. Since only one SDO
communication can be sent for a time, do NOT use this instruction for outputting positioning in various axis
synchronized motion.
Example 1 (Ladder diagram):
until SM1681 is ON.
SM1652 is ON, it indicates Servo-ON.
3. When M2 changes from OFF to ON, servo 2 moves to the relative position 100000 PUU at 100.0 rpm.
The finish flag SM1632 is ON when the target position is reached.
6_
6-987
Example 2 (Structured Texts programming language):
1. When M2 changes from OFF to ON, servo 2 moves to the relative position 100000 PUU at 100.0 rpm.
2. Make sure M2 and SM1632 are both ON and then set the auto return communication control right flag SM1582 to
Explanation of special flags (SM) and registers (SR) for Delta special CANopen communication instructions
The following table shows special flags (SM) and registers (SR) related to Delta special CANopen communication.
Flag R/W ID. 1 ID. 2 ID. 3 ID. 4 ID. 5 ID. 6 ID. 7 ID. 8
The flag in HWCONFIG is set to ON when the PLC changes from Stop to
Enable specific function R/W
Run.
Initialization and communication

_6 complete (INITC and CASD)
R SM1681
CANopen communication error R SM1682
Single slave initialization SM1686 = OFF (default; multiple slaves initialization)

R/W
(for firmware V1.06.40 or later) SM1686 = ON (single slave initialization)
Positioning complete R/W #1 SM1631 SM1632 SM1633 SM1634 SM1635 SM1636 SM1637 SM1638
Stop R/W SM1641 SM1642 SM1643 SM1644 SM1645 SM1646 SM1647 SM1648
Servo-ON R SM1651 SM1652 SM1653 SM1654 SM1655 SM1656 SM1657 SM1658
Go-back/go-forth enabled
R/W SM1661 SM1662 SM1663 SM1664 SM1665 SM1666 SM1667 SM1668
Only DDRVAC is supported.
Go-back/go-forth direction indicator
R SM1671 SM1672 SM1673 SM1674 SM1675 SM1676 SM1677 SM1678
Only DDRVAC is supported.
Auto return communication control SM1581 SM1582 SM1583 SM1584 SM1585 SM1586 SM1587 SM1588
R/W
right
Heartbeat error code R SM1691 SM1692 SM1693 SM1694 SM1695 SM1696 SM1697 SM1698
SM1684 = OFF (default; when one goes down, all the servos are OFF.)
Heartbeat error handling R/W
SM1684 = ON (when one goes down, only the defective servo is OFF.)
Number of the axis with a
R SR658
communication error
6-988
Communication error code R SR659
Note1: After the axis starts to output, PLC clears the corresponding completion flag.
The following table shows how Delta servo parameters of axes correspond to special flags and registers in the CANopen
communication.
Servo Parameter Name (Number) R/W ID. 1 ID. 2 ID. 3 ID. 4 ID. 5 ID. 6 ID. 7 ID. 8
PR command (P5-07) R SR661 SR662 SR663 SR664 SR665 SR666 SR667 SR668
Alarm code (P0-01) (hexadecimal) R SR671 SR672 SR673 SR674 SR675 SR676 SR677 SR678
DO state (P0-46) R SR681 SR682 SR683 SR684 SR685 SR686 SR687 SR688
SR691 SR693 SR695 SR697 SR699 SR701 SR703 SR705

Servo command positon CMD_O (P0-09) R

Servo target position CMD_E (P0-10) R
DI state (P4-07) R SR731 SR732 SR733 SR734 SR735 SR736 SR737 SR738
Current torque (unit: 0.1%) R SR741 SR742 SR743 SR744 SR745 SR746 SR747 SR748
Self-defined (P0-12) * SR791 SR793 SR795 SR797 SR799 SR801 SR803 SR805
R
Work with SM1685 Enable/Disable SR792 SR794 SR796 SR798 SR800 SR802 SR804 SR806
Positioning completion range setting R/W SR811 SR812 SR813 SR814 SR815 SR816 SR817 SR818
6_
*For example, if a servo real position is requested, set the sero values in P0-20, enable SM1685 and then the servo real
position can be read in SR791-SR806. For more details, refer to Delta High Resolution AC Servo Drive for Network
Communication Applications ASDA-A2 Series User Manual.
The following table shows how Delta inverter parameters of axes correspond to special flags and registers in the
CANopen communication.
Description ID. 21 ID. 22 ID. 23 ID. 24 ID. 25 ID. 26 ID. 27 ID. 28
Initialization complete flag R SM1683
Inverter starting up flag R SM1621 SM1622 SM1623 SM1624 SM1625 SM1626 SM1627 SM1628
Inverter Heartbeat error flag R SM1611 SM1612 SM1613 SM1614 SM1615 SM1616 SM1617 SM1618
Auto return communication

control R/W SM1601 SM1602 SM1603 SM1604 SM1605 SM1606 SM1607 SM1608
right
Inverter status
R SR751 SR752 SR753 SR754 SR755 SR756 SR757 SR758
(Index 6041H-00H)
Inverter current velocity
(Index 6043H-00H)
6-989
Inverter current torque

(unit: 0.1%) R SR771 SR772 SR773 SR774 SR775 SR776 SR777 SR778
(Index 2021H-0CH)
Inverter digital input status
(Index 2022H-11H)
The following table shows the Delta special drier CANopen error codes. (error code in SR659)
Error Code Cause
0x0002 The slave does not respond to the SDO message.

An error occurs in the message received by the slave. This error often occurs when the settings of the
0x0003 COPRW instruction are invalid causing the slave not to receive the complete message.
0x0004 The slave PDO message is not received.
0x0005 An error occurs while using the instruction operand.
0x0006 One of the stations is being used when the INITC instruction is executed.
0x0007 Slave station address exceeds acceptable range of the instruction INITC
A slave cannot be reset; check if the communication cable is connected and if the communication of the
0x0008 slave is working properly.
_6
6-990
2804 D DRVAC S1, S2, S3 Servo absolute position control

S1   
S2    
S3 DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  

－－ AS
Symbol
S2 ： Absolute target position
S3 ： Target speed
6_
Explanation
1. This instruction executes the servo absolute position control for the servo at the address specified in S1. Before you
execute this instruction, the INITC and ASDON (Servo-ON) instructions must be complete.
2. The range of S1 is 1–8. There will be no execution when the input value is out of the range.
3. The range of S2 is -2147483648 to +2147483647. The +/ - sign indicates the forward / reverse direction. The target
position is an absolute position.
4. Refer to the DRVIC instruction (API 2803) for additional information and examples.
6-991
Example 1
until SM1681 is ON.
3. When M2 changes from OFF to ON, servo 2 moves from the current position to the absolute position 100,000 PUU
at 100.0 rpm.
_6
6-992
Example 2
1. Add one line to the program in Example 1. When the PLC runs and SM1662 is ON, the function is enabled for servo
2 to go back and forth.
2. As the figure shows below, the servo moves from its current position (20,000) to the absolute target position
(100,000) after M2 is ON. After that, it goes back and forth between the absolute position 100,000 and 0.
The direction indication flag SM1672 is ON when the servo goes toward the target position for the first time after
Servo-ON. After that, the flag repeats the state, changing from ON to OFF.
3. You can modify the target position at any time in the motion, but the new target position is only valid for the next
back and forth cycle.
6_
6-993
2805 D PLSVC S1, S2 Servo speed control

S1   
S2    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  

－－ AS
Symbol
S1 ： Station address of a servo
S2 Target speed
Explanation
_6 1. This instruction executes the servo speed control for the servo at the address specified in S1. The INITC and
ASDON (Servo ON) instructions must be complete before this instruction is executed.
the range.
3. Table to describe S2
Servo type Range of S1 Range of S2 Descriptions of S2

The +/- sign indicates the forward / reverse direction. For
-60000 - 60000 example, when inputting 6005 in S2, the value is
Servo 1-8
(0.1rpm) 600.5rpm.
-32768 - 32767 The +/- sign indicates the forward / reverse direction. For
Inverter 21-28
(1rpm) example, when inputting 605 in S2, the value is 605rpm.
4. For corresponding SM and SR of the axes, refer to the DRVIC instruction (API 2803).
6-994
Example 1 (communication with Delta servo systems)
until SM1681 is ON.
3. When M2 changes from OFF to ON, servo 2 moves at 100.0 rpm until M2 is OFF.
6_
6-995
2. When M1 changes from OFF to ON, this instruction starts to set the acceleration time and deceleration time at the
station address 21.
3. When M2 changes from OFF to ON, this instruction starts to set the control mode at the station address 21.
4. When M3 changes from OFF to ON, the inverter moves at 2500rpm until M3 goes OFF.
_6
6-996
2806 D ZRNC S1, S2, S3 Servo homing

S1   
S2    
S3 DWORD    
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2   
S3   

－ AS AS
Symbol
S2 ： The 1st – segment speed
S3 ： The 2nd – segment speed
Explanation
6_
1. This instruction executes the servo homing control for the servo at the address specified in S1. The INITC and
ASDON (Servo-ON) instructions must be complete before this instruction is executed. It is recommended to use the
instruction ZRNM (API 2810) to have every servo axis go back to the zero point.
2. The range of S1 is 1–8 (for servo. There will be no execution when the input value is out of the range.
3. The range of S2 is 1–20000. Unit: 0.1 rpm (servo drive parameter P5-05); if you need to use linear motor drive and
the first section exceeds 32767, you need to use DZRNC instruction instead (only available for PLC FW V1.04 or
later).
4. The range of S3 is 1–5000. Unit: 0.1 rpm (servo drive parameter P5-06)
5. When the servo returns to the home position, the corresponding finish flags of the axes are ON. Refer to the DRVIC
instruction (API 2803) for explanations of special flags (SM) and registers (SR).
6-997
Example
1. When M0 changes from OFF to ON, the INITC instruction starts to initialize servo 1, until SM1681 is ON.
2. When M1 changes from OFF to ON, the acceleration time (10000) and deceleration time (20000) of servo 1 are set
by using the CASD instruction (API 2802). When SM1651 is ON, it indicates Servo-ON.
3. When M2 changes from OFF to ON,
2-byte data is written to P5-04 in servo 1. When D100 = 5 and the data is written, M100 is ON.
P5-04 sets the homing mode.
P6-00 and P6-01 are the homing definitions.
4. When M3 changes from OFF to ON, the homing function is enabled for servo 1.
_6
6-998
6_
6-999
Reading and writing CANopen

2807 COPRW S1, S2, S3, S4, S5, D communication data

S1   
S2    
S3    
S4    
S5 
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
S1  
S2  
S3  
S4  
S5  
D 

－ AS －
_6 Symbol
S1 ： Station address of servo or slave
S2 ： Request code
S3 ： Index
S4 ： Sub-index
S5 ： Read/write device
D ： Communication completion flag
Explanation
1. This instruction reads and writes CANopen communication data to the servo at the address specified in S1. The
range of S1 is 1–127. If the value is out of range (<1 or >127), the minimum or maximum value is automatically
processed by the instruction as the value of S1.
2. S2 can only specify four types of request codes, as shown in the following table. If you set the request code wrong, it
does NOT execute; SM1682 is ON and SR659 is 16#0005.
6-1000
S2
(only available for Description
values of lower 8-bit)
16#0023 Writing the 4-byte data; Expedited SDO
16#002B Writing the 2-byte data; Expedited SDO
16#002F Writing the 1-byte data; Expedited SDO
Reading the data. The data length is contained in the SDO response message;
16#0040
Expedited SDO
16#0021 Data and its length are specified by S5; Normal SDO
16#0041 Reading the data and store the read data and its length in S5; Normal SDO
3. For S3 and S4, refer to the object dictionary in the Delta servo / inverter operation manual or the object dictionary
from a third-party device that complies with CANopen DS301.
4. You should execute the COPRW instruction only after the INITC instruction is complete in case the parameters are
overwritten by the INITC instruction. Use the COPRW instruction for CANopen SDO communication. If the station
address of a slave exceeds the range 1–8 or 21-28, you can use the COPRW instruction to set, read, and write
slave-related parameters.
When you use Delta Special Driver & AS Remote mode / Delta Special Driver & CANopen DS301 and execute
COPPRW instruction (SDO communication), the communication timeout is shown below.

6_
Communication timeout (ms)#1 100 100 200 400 500
When the mode is CANopen DS301, you can set the time of the COPRW timeout in the CANopen communication
setting option from HWCONFIG; default timeout is 100 ms.
in which the error occurs and SR659 retains the error code. Refer to DRVIC instruction for details.
Note: When you use the COPRW instruction, you must edit the process for dealing with communication errors in
order to avoid invalid communication occurring as a result of unexpected communication errors.
6. The diagram below shows the timing of the COPRW instruction.
 When you enable the COPRW instruction for the first time, the instruction sends the command code immediately
if no other CANopen communication is using it.
 The instruction sends the command code.
 The code has been sent and the finish flag is set to ON.
6-1001
 You modify the next data to be sent out. The next command code is sent out immediately after the finish flag is
set to OFF.
The code has been sent and the COPRW instruction is disabled.
7. The COPRW instruction only supports the Delta Special Driver & AS Remote Mode and CANopen DS301 in the
hardware configuration setting (HWCONFIG in ISPSoft).
_6
8. Most of the parameters in Delta ASDA-A2 are displayed in the decimal format. You can convert the parameters into
index addresses, see the example below. 0 is a fixed value for the sub index address.
Example: The index address of PX-YY=0x2000 +（X << 8）+ YY
P2-10 = 0x2000 +（0x0002 << 8）+ 0x000A = 0x220A
P5-04 = 0x2000 +（0x0005 << 8）+ 0x0004 = 0x2504
P1-44 = 0x2000 +（0x0001 << 8）+ 0x002C = 0x212C
6-1002
9. Most of the parameters in Delta inverter are also displayed in the decimal format. Use the following formula to
convert the parameters.
Example: The index address of PXX-YY=0x2000 + XX (hexadecimal);
The sub index address is YY+1 (hexadecimal)
The index address of P10-15 = 0x2000 + 0x000A = 0x200A
The sub index address is 0x0F+1= 0x10
10. Since this instruction uses SDO (Service Data Objects) and the communication mode is one transmission (one
sending/one receiving) at a time, and the communication right is shared with the high-speed output instructions.
When writing PLC programs, bear the followings in mind.
 It is suggested NOT to use 2 COPRW instructions or communication at a time in one scan cycle.
 It is suggested NOT to use COPRW in communication keep enabled mode.
 It is suggested NOT to use this instruction in a function block. Because when this instruction is written in a
function block, there will be 2 POUs in the PLC program and when the function block is called, 2 instructions
will be enabled at the same time.
11. The request codes for normal SDO are 16#0021 and 16#0041, available for PLC with firmware V1.04.80 or later.
12. When the request code is 16#0021, S5 is the data length (“n” byte) to write into the slave. S5+1~ S5+((n+1) / 2) is the
data to write into the slave. For example, if S5 is specified as D100 and the value in S5 is 16. This instruction sends
data in D101 ~ D108 to the slave in the following order, lower 8-bit in D101, upper 8-bit in D101, lower 8-bit in D102,
6_
upper 8-bit in D102 and so forth.
13. When the request code is 16#0041, when received responses from the slave, this instruction stores the data length
(“n” byte) in S5 and data in S5+1~ S5+((n+1) / 2). For example, if received 15 bytes of data length, D100 is 15 and
store the data Byte[0], Byte[1].. Byte[14] in the following order, lower 8-bit in D101, upper 8-bit in D101, lower 8-bit in
D102, upper 8-bit in D102 and so forth.
14. The maximum data length is 255 bytes. To prevent too many Normal SDO transmissions, if the data length exceeds
255 bytes, PLC only sends or receives 255 bytes.
6-1003
Example (using Expedited SDO)
until SM1681 is ON.
2. When M1 changes from OFF to ON, the PLC writes the 2-byte data (S2=16#002B) in D100 to P5-04 (S3=16#2504)
of servo 3, using the COPRW instruction. When the writing is complete, M100 is ON.
3. When M2 changes from OFF to ON, the PLC reads the value of P4-07 (S3=16#2407) of servo 3 and stores the
value( S2=16#0040) in D106. When the reading is complete, M106 is ON.
_6
6-1004

Writing multiple CANopen parameter
2808 D COPWL S1，S2，S3，D
values

S1   
S2  
S3   
D    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
S1  
S2    
S3  
D 

－ AS AS
Symbol
S1 : Station address(Mac ID)

Starting source device where written
S2 :
data are stored
Number of messages to
S3 :
consecutively write data
6_
D : Communication completion flag
Explanation
1. S1 sets the station address within the range of 1~127. If the setting value exceeds the range (< 1 or >127), the
instruction will automatically send data at the minimum or maximum value respectively.
2. S2 is the starting source device where written data are stored and S3 is the number of messages to consecutively
write data. E.g., S2 specifies D10 as the starting device and the number of messages to consecutively write data is 3.
Here is the detailed explanation in the following table.
Instruction name Message No. Index address Subindex address Written source data
1 D10 D11 D12
COPWL
2 D13 D14 D15
(Writes 16-bit values)
3 D16 D17 D18
1 D10 D11 D12, D13
DCOPWL
2 D14 D15 D16, D17
(Writes 32-bit values)
3 D18 D19 D20, D21
The value of S3 is in the range of 1~100.
6-1005
3. For the index addresses and subindex addresses of Delta servo and AC motor drive, refer to the explanation of the
COPRW instruction. In principle, the parameter values of Delta servo and AC motor drive are both16-bit or 32-bit
values including floating point numbers. If you need write an 8-bit value, use the COPRW instruction.
4. D is the communication completion flag. D will turn on after the sending of multiple communication messages is
complete.
See the detailed sending process and sequence diagram below.
 The COPWL instruction is enabled and starts to send data.
 After the COPWL instruction sends one piece of message, the next PLC instruction continues to execute.
 As the COPWL instruction is scanned once again and the prior message has been received by the slave, the
COPWL instruction sends the next message.
 When the last written-data sending is done, the instruction will set the completion flag to ON.
 When the completion flag turns on, the COPWL instruction need be disabled by manual so that the subsequent
COPWL or COPRW instruction can continue to work.
Note: When you disable the instruction, the completion flag will be automatically cleared accordingly.
enable enable
disable disable
_6 COPWL
    

S2 1 2 3 1

Note: The sequence diagram above shows the sending of 3 pieces of written data.
5. After the instruction is enabled, wait until the writing is complete and then disable the instruction. If there is a
communication error in the execution, shoot the trouble and then re-enable the instruction to write all data.
6-1006
Example
1. When M1 = OFF → ON, data are written in D device.

Subindex
Instruction name Data No. Index address Written data source
address
D50 = 16#212C
1 (E-gear ratio D51 = 0 D52, D53 = 77777777
DCOPWL numerator)
(Writes 32-bit values) D54 = 16#212D
2 (E-gear ratio D55 = 0 D56, D57 = 88888888
denominator)
2. When M1 = OFF → ON, the instruction writes a 32-bit value for P1-44 of the servo whose station address is 2 and
the written value 77777777 is stored in D52. The instruction writes a 32-bit value for P1-45 and the written value
88888888 is stored in D56. As the writing is complete, M201 turns on.
6_
6-1007
2809 RSTD Node，Para，Ok，Err Sending Reset or NMT command

Node   
Para   
Ok   
Err   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Node 
Para 
Ok 
Err 

－ AS －
Symbol
Node : Station address which is reset
Para : Setting value of the parameter

_6
Ok : The reset completion flag
Err : The reset error flag
Explanation
1. Before the RSTD instruction is used in Delta special instruction mode, make sure that all Delta drives have been
initialized via the INITC instruction and they once worked normally.
2. When used in CANopen DS301 mode, the RSTD instruction works as the NMT communication function and can
switch network states via the Para parameter.
3. Only the PLC firmware of V1.04.10 and later and the ISPSoft software of V3.03.08 and later support the
instruction.
4. When CAN communication port is specified to work in Delta special driver mode, the value of Node can be 0 (for
the broadcast function) and 1~8 which are for servo station addresses only and 21~28 for station addresses of AC
motor drives only. When the station address exceeds the range, the PLC will not perform the reset action and the
Err flag turns on. (Refer to the explanation of SR659 for error codes)
5. When CAN communication port is specified to work in CANopen DS301 mode, the value of Node is in the range of
6-1008
1~64 and 0 (for the broadcast function). When the value exceeds the range, the PLC will not perform the NMT
communication and the Err flag turns on. (Refer to the explanation of SR659 for error codes)
6. The setting value of Para is only applicable to CANopen DS301 mode. The parameter is meaningless if the
instruction is used in Delta special driver mode and AS remote mode. The settings for Para (NMT service code)
are listed in the following table. If the setting value is not one of the values in the table, the Err flag turns on.
NMT
16#01 16#02 16#80 16#81 16#82
service code
Enter the pre- Reset the
Function Reset the
Start the slave Stop the slave operational application
description communication
state layer
7. The RSTD instruction can implement the command action on only one drive or slave every time. If multiple RSTD
instructions are enabled simultaneously, the PLC will automatically take priority to perform the instruction which is
enabled earlier.
8. The RSTD instruction is executed to send the command when it is enabled. If the instruction is disabled before the
Ok flag is on, the PLC will not set the Ok flag to ON.
9. Apart from notifying the specified drive to clear the error state, the instruction would also re-check if relevant
communication parameter values are correct and re-set correct communication parameter values.
For example, due to the disconnection of the slave of station address 2, the entire system stops running. After the
trouble is solved, the slave of station address 2 can return to the state of being controllable by using the RSTD
instruction to reset the slave of station address 2 only. So the time of re-initializing all drives are saved. 6_
10. If the slave responds by sending back any communication command fault to the PLC during the communication,
the RSTD instruction will turn the Err flag on and stop the upcoming actions. (Refer to explanation of SR659 for
error codes.)
6-1009

Setting the homing mode for Delta
2810 ZRNM Node，Mode，Ok，Err
servo

Node   
Mode   
Ok   
Err   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
Data
CNT
INT
type
Node 
Mode 
Ok 
Err 

－ AS －
Symbol
Node : Specified node ID
Mode : Homing mode code
Ok : Completion flag
_6
Err : Error flag
Explanation
1. Make sure that all Delta drives have been initialized before executing the reset instruction.
2. Only the PLC firmware of V1.04.10 and later and the ISPSoft software of V3.03.08 and later support the
instruction.
3. The value of Node is in the range of 1~8 (exclusive to servo node IDs). If the setting value exceeds the range, the
PLC will not perform the action of the homing mode and set the Err flag to ON. (Refer to explanation of SR659 for
error codes.)
4. The ZRNM instruction can set the homing mode of only one drive every time. If multiple instructions are enabled
simultaneously, the PLC will take priority to perform the instruction which is enabled earlier.
5. The ZRNM instruction is executed to send the command when it is enabled. If the instruction is disabled before the
Ok flag is on, the PLC will not set the Ok flag to ON.
6. Mode sets a homing mode. If the setting value exceeds the range, the PLC will still send the command and the
server itself will decide whether to receive the command or not. The setting mode is the homing mode that ASDA
6-1010
servo parameter P5-04 corresponds to.
The setting value of Delta servo homing mode is a hex value. The value is defined as the format of 0xWZYX. See
the explanation of respective codes as below.
Homing
Range Function and code description Remark
mode code
Select the final position where the servo stops.
0 = The servo leaves the home position, decelerates and stops
W 0~1 and then automatically returns to the actual home position.
1 = After leaving the home position, decelerating and stopping,
the servo will not perform any action any more.
Handling mechanism when the limit is encountered.
Z 0~1 0 = Output stops.
1 = Output is conducted in the reverse direction.
Z pulse signal setting (used for X code 0~8 )
0 =Look for Z pulse when coming back. Do not look for Z
phase when going forward.
1 =Go forward to Z pulse. Do not look for Z pulse when coming
back.
6_
Y 0~2
2 =Do not look for Z pulse.
Z pulse signal handling method (applicable to X code: 9~A)
0 =Look for Z pulse when coming back.
1 =Do not look for Z pulse both when coming back and going
forward.
Homing method: 0~8
0 = Homing in the forward direction; PL is the home position.
1 = Homing in the reverse direction; NL is the home position.
2 = Homing in the forward direction; ORGP: OFF > ON, as the
home position.
X 0~A 3 = Homing in the reverse direction; ORGP: OFF > ON, as the
home position.
4 = Homing in the forward direction; look for Z pulse and
regard it as the home position.
5 = Homing in the reverse direction; look for Z pulse and
regard it as the home position.
6 - 1 0 11
6 = Homing in the forward direction; ORGP: ON > OFF, as the
home position.
7 = Homing in the reverse direction; ORGP: ON > OFF, as the
home position.
8 = Current position is the home position.
Homing method: 9~A
9 = Homing in the forward direction; the collision point is the
home position.
A = Homing in the reverse direction; the collision point is the
home position.
_6
6-1012
2811 EMER Node，Dest，Len，Ok，Err Reading Emergency message

Node   
Dest 
Len 
Ok   
Err   
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Node 
Dest 
Len 
Ok 
Err 

－ AS －
Symbol
Node : Specified node ID

6_
Dest : Target device for storing data
Len : Total number of 4 words of data which have been read
Ok : Completion flag
Err : Error flag
Explanation
1. The EMER instruction is applicable to CANOpen DS301 mode and Delta special mode.
2. Only the PLC firmware of V1.04.10 and later can support the instruction.
3. After receiving the Emergency message from the slave Node, the PLC will automatically store the data in the
specified storage device and set the Ok flag to ON.
4. It is recommended that the Node value should be specified from the slave node IDs which have already existed. If
the value is not one existing node ID or the slave has been disconnected, the PLC will not be able to receive any
message, set the Err flag to ON and show error code of communication timeout. (Refer to explanation of SR659
for error codes.)
6-1013
5. The way the EMER instruction reads Emergency messages is the same as Emergency communication method in
AS operation manual. Please just select one communication method from them when reading Emergency
messages.
6. The EMER instruction can read 5 Emergency messages at most. Every time the reading is successful, the Ok flag
turns on and Len displays the total number of messages which are read. You can judge how many consecutive
words are occupied by Dest based on the length. Every message uses 4 words. The data are stored in the order
from lower 8 bits to higher 8 bits. The storage format is shown as below. (E.g. Dest is D10, Len is 2 which is the
number of messages stored in D5.)
D device no. Value

D5 2
D device no. Higher 8 bits Lower 8 bits
D10 The second byte in the first message The first byte in the first message
D11 The forth byte in the first message The third byte in the first message
D12 The sixth byte in the first message The fifth byte in the first message
D13 The eighth byte in the first message The seventh byte in the first message
The second byte in the second

D14 The first byte in the second message
message
D15 The forth byte in the second message The third byte in the second message
_6
D16 The sixth byte in the second message The fifth byte in the second message
The seventh byte in the second

D17 The eighth byte in the second message
message
6-1014
CSFOC Xno ~ OutSpd Controlling the tracking function of a

2812 D
servo via communication

Xno 
InCnt 
InSpd 
Gear  
Axis   
OutCnt 
OutSpd 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Xno 
InCnt  
InSpd  
Gear 
Axis 
OutCnt  
OutSpd  

－－ AS
6_
Symbol
Xno : Signal input device
InCnt : Number of input pulses
InSpd : Pulse input frequency
Gear Proportion of the input frequency and output frequency

:
(floating-point value)
Axis CANopen communication station address of Delta

:
servo
OutCnt Number of output pulses (unit: per user unit (PUU))
OutSpd Pulse output frequency
6-1015
Explanation
1. For execution of this instruction, you need to use PLC FW V1.06 or later and ISPSoft V3.07 or later.
2. The INITC and ASDON (Servo-ON) instructions must be complete before this instruction is executed.
3. Xno can only specify X0.0, X0.2, X0.4, X0.6, X0.8 and X0.10 as the input points, and the operand occupies two
consecutive input points. You cannot execute the instruction if the input points are the points specified for Xno
above. After you select the input points, the high-speed counter is automatically specified. If there is a DCNT
instruction (API 1004) or CSFO instruction (API 2708) with the same high-speed counter in the program, the PLC
first executes the instruction that starts the counter first. The input points and corresponding high-speed counters
are shown in the following table.
Group number 1 2 3 4 5 6
Xno+0 input point

X0.0 X0.2 X0.4 X0.6 X0.8 X0.10
(Phase A)
Xno+1 input point

X0.1 X0.3 X0.5 X0.7 X0.9 X0.11
(Phase B)
High-speed counter
HC202 HC206 HC210 HC214 HC218 HC222
number
Flag for reversing input

SM270 SM271 SM272 SM273 SM274 SM275
direction
_6
4. If the high-speed counters for the instruction can use only the phase A/B input mode, set the flag for reversing the
input direction to ON when MPG is connected but has not rotated yet, and the PLC input point is ON. Set the
function to detect the state of PLC run cycle to OFF.
5. InCnt is the number of input pulses. Use a 32-bit variable to declare the parameter.
6. InSpd is the frequency of input pulses. Use a 32-bit variable to declare the parameter with the unit of 1 Hz.
7. Gear is the proportion of the input frequency and output frequency (floating-point value). The formula is that output
frequency equals to the result of input frequency multiplying Gear. For instance, if Gear is 2.5 and the input
frequency is 50, the output is 125 (50*2.5). Note: the output count and the output frequency are rounded down to
the nearest whole digit when outputting.
8. Axis is the station address of Delta servo for output, ranging from 1 to 8 and it should be within the station address
that is initiated by the INITC instruction.
9. OutCnt is the number of output pulses. Use a 32-bit variable to declare the parameter with the unit of PUU.
10. OutSpd is the frequency of the output pulses. Use a 32-bit variable to declare the parameter with the unit of 1 Hz.
6-1016
11. There is no limit to the number of times you can use this instruction. Several instructions can use one group of
input points as its source of input count. But you need to clear the value in the input counter before execution of
this instruction; especially when you are using one input and several outputs. And this instruction executes
according to the axis number to record information about its input and output. The same axis can be used for
several times but you must not output the same axis at the same time. If you use the same axis to output for
several times, PLC outputs the first starting one and then the second one.
only once.
Note
1. The PLC calculates the input pulse frequency based on the input pulse width (ON) in the positive half cycle. If the
proportion of the pulse width for ON:pulse width for OFF is not 1:1, the PLC takes the ON width as the standard for
conversion by default.
2. The input pulse=ON means the input point LED is on. When using the MPG but it has not rotated yet, you can check
if the input point LED is OFF and the flag for reversing the input direction is activated .
3. There is a 20 ms time difference in CANopen communication when executing this instruction. If this worries you, use
CSFO instruction instead, controlling the servo by the pulse output.
Example
6_
 When M0 switches from OFF to ON, PLC starts to execute this instruction to initialize servo station address 1 and
2 until SM1681 is ON.
 When M1 switches from OFF to ON, PLC starts to execute this instruction to start servo station address 1 and
when the servo is started, SM1651 is ON, meaning Servo-ON.
 When M2 switches from OFF to ON, PLC starts to execute this instruction to start servo station address 1 and
when the servo is started, SM1652 is ON, meaning Servo-ON.
 When M3 switches from OFF to ON, input points X0.0 and X0.1 connect to the MPG to control 2 servos. The
proportions for the 1st servo is 1 and for the 2nd servo is 2.
6-1017
_6
6-1018
ECAMD Downloading E-CAM chart to the

2813 Slave ~ ErrCode
Slave

Slave   
Source    
Len   
CAddr   
Done   
Err   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Slave  
Source  
Len  
CAddr  
Done 
Err 
ErrCode  

－ AS －
6_
Symbol
Slave ： Servo slave station number
Source ： From which E-CAM chart to start downloading
Len ： The length of the E-CAM chart
CAddr ： From which address to start storing E-CAM chart in

the servo
Done ： Downloading complete flag
Explanation
2. Slave is where you store the downloaded E-CAM chart; the supported slave station ranges from 1 to 8. After the
downloading is complete, the DONE flag is ON. If the slave station number you are using is out of the supported
range, the instruction is NOT executed. And the Err (error) flag is ON.
6-1019
3. Source is where you specify from which E-CAM chart to start downloading; the supported E-CAM chart length is
from 1 to 16. If the E-CAM chart number you are using is out of the supported length, the instruction is NOT
executed. And the Err (error) flag is ON. You can also use the PLC data register number to specify from which E-
CAM chart to start downloading to the servo and it takes Len+1 as its downloading length. After the setting is done,
the system starts to read from the specified data register number (device number) to a length of Len +1 (32-bit)
consecutively to the servo. If the Source is D10 and the Len is 10, the system starts to read from D10 to a length of
10+1, starting from D10/D11, D12/D13 to D30/D31 to the servo.
4. Len is the E-CAM chart length for downloading; its setting range is from 1 to 720. If the length you are using is out of
the supported range, the instruction is NOT executed. And the Err (error) flag is ON. The servo supports up to 800; if
the Len+1 exceeds 800, PLC stops downloading and the Err (error) flag is ON.
5. CAddr is the starting address where to store the E-CAM chart in the servo; the supported setting range is from 0 to
798. If the starting address you are using is out of the supported range, the instruction is NOT executed. And the Err
(error) flag is ON.
6. If the supported 16 E-CAM charts are not sufficient, you can choose to download the E-CAM charts to the PLC file
register while editing in the E-CAM Editor.
7. You can make use of the 1st ~ 800th storage in the servo. When creating E-CAM charts with not so many points (less
than 800), you can download the E-CAM charts altogether at one time to save communication time. For example, if
you use points 1-200 in chart A and 201-400 in chart B, the points in chart A plus the points in chart B are 400 (less
_6
than 800), you can download these two charts at one go.
8. Once executing this instruction, it clears the Done flag first and then sends the E-CAM chart. Once the transmission
is complete, the Done flag is ON. If any error occurs from the slaves, the Err (error) flag is ON. If you need to resend
the E-CAM chart, you need to wait for one scan time before executing this instruction again.
9. If the Err (error) flag is ON, refer to the definitions below.
ErrCode Description
0001 This slave station number is NOT in the supported range.
0002 This E-CAM chart number is NOT in the supported range.
0003 This CAddr. Address or length is NOT in the supported range.
0004 No response from the slave.
0005 Error message sent from the slave while downloading or setting up.
The PLC is NOT in the Delta Special Driver & AS Remote Mode nor in the Delta Special
0006
Driver & CANopen DS301 Mode.
6-1020
E-CAM parameter setting and

2814 D ECAMS Slave ~ ErrCode
planning

Slave   
Smode   
CAddr   
CLen   
Rpuu   
Cmode   
WbPuu   
OutT   
CaPuu   
CwPuu   
Orate   
Done   
Err   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Slave  
Smode  
CAddr  
CLen   6_
RPuu  
Cmode  
WbPuu  
OutT  
CaPuu  
CwPuu  
ORate  
Done 
Err 
ErrCode  

－－ AS
6-1021
Symbol
Command source for encoder of the master

Smode ：
axis
From which address to start storing E-CAM

CAddr ：
chart in the servo
CLen ： Specified E-CAM chart length for executing
Number of pulses for the master’s E-CAM to

RPuu ：
rotate a full 360 cycle
Cmode ： Engaging condition
Number of pulses for E-CAM to wait before

WbPuu ：
engaging for the first time (32-bit value)
OutT ： Disengaging condition

CaPuu ：
disengaging (32-bit value)

CwPuu ：
engaging again (32-bit value)
ORate ： Output ratio for E-CAM chart (32-bit value)
_6 Done ： Downloading complete flag
Err ： Error flag
Explanation
2. This instruction is for setting up the E-CAM related parameters for the first time or setting up the E-CAM chart before
the first engagement. If you need to modify the E-CAM chart during engaging, you need to use instruction ECAMC
(API2816) instead.
3. Slave is the servo slave station, ranging from 1 to 8. If the slave station number you are using is out of the supported
range, the instruction is NOT executed. And the Err (error) flag is ON. After modifying and the specified servo slave
station responds correctly, the DONE flag is ON.
4. Smode is where you can set the command source for encoder of the master axis; the options are as shown below.
6-1022
Command Source of Master Description
Axis
０ CAP axis (defined by CAP function)
１ Auxiliary encoder (P5-17)
2 Pulse command (A/B phase pulse) (P5-18)
3 PR command: the value of absolute coordinate from position command
4 Time axis (1ms)
5 Synchronous capture axis (P5-77)
6 Analog channel 1 (virtual axis; unit: 10 V corresponds to 1 M pulse/S)
12 Pulse command (CW/CCW pulse) (P5-18)
22 Pulse command (Pulse/Dir pulse) (P5-18)
Other numbers Treated as option 2: Pulse command (A/B phase pulse) (P5-18)
5. PLC sets up the servo parameter P5-88.Y according to the command source of the master axis. When the
command source is Pulse Command, you need to set up the pulse type via the servo parameter P1-00 while the
servo is OFF.
6_
(error) flag is ON. PLC sets the servo parameter P5-81 (start address of data array).
7. CLen is the specified E-CAM chart length for executing; its setting range is from 5 to 720. E-CAM chart is divided
into CLen and the chart should include CLen +1 data. The servo supports 1st ~ 800th space; if the starting address is
501 and set the CLen to 400, this arrangement takes 902 (501+401) space which exceeds the 800th space, the
instruction is NOT executed and the Err (error) flag is ON. PLC sets the servo parameter P5-82. Write this
parameter when E-CAM stops (P5-88, X=0).
8. RPuu is where you set the number of pulses for the master’s E-CAM to rotate a full 360 cycle; servo unit: PUU (per
user unit). The value in RPuu should be 32-bit and ranges from 10 to 1073741823. When the value exceeds the
upper or lower limit, it will be seen as the maximum vlaue or the minimum value. PLC sets the servo parameter P5-
83 and P5-84. Write the parameters when E-CAM stops (P5-88, X0=0).
9. Cmode is where you can set the engaging condition; the options are as shown below.
Mode Description
0 Engage immediately
1 DI: CAM ON
2 Any one of the Capture
6-1023
Other numbers Treated as Mode 0, to engage immediately
10. PLC sets the servo parameter P5-88.Z (engaging time).
11. WbPuu is where you set the number of pulses for E-CAM to wait before engaging for the first time. The value in
WbPuu should be 32-bit and ranges from -1073741824 to +1073741823. When the value exceeds the upper or
lower limit, it will be seen as the maximum vlaue or the minimum value. When the value is 0, it means no waiting
before the first engagement. PLC sets the servo parameter P5-87.
12. OutT is where you can set the disengaging condition; the options are as shown below. Option 2, 4 and 6 cannot be
selected at the same time.
Mode Description After disengaged
0 Never disengaged -
1 DI: CAM OFF In STOP status
Master axis receives the pulse number

2 In STOP status
which is set by CaPuu (P5-89).
Master axis exceeds the setting value in Back to the pre-engaged status.
4
CaPuu (P5-89). The pre-engaged pulse is CwPuu (P5-92).
Same as 2; master axis receives the pulse
_6
number which is set by CaPuu (P5-89) but
here E-CAM keeps its velocity while
6 disengaging. Master axis exceeds the setting In STOP status
value in CaPuu (P5-89) a little bit. Suitable
for the application of using the PR position
command right after disengaged.
Work with option 1, 2 or 6; disable E-CAM after

Set the servo parameter P5-88.X0 to 0.
it is disengaged.
8
Work with option 4, to avoid jittering when it
-
returns to pre-engaging status
Other
Treated as Mode 0, to engage immediately
numbers
13. PLC sets the servo parameter P5-88.U (disengaging time).
14. CaPuu is where you set the number of pulses for E-CAM to wait before disengaging. The value in CaPuu should be
32-bit and ranges from -1073741824 to +1073741823. When the value exceeds the upper or lower limit, it will be
seen as the maximum vlaue or the minimum value. When the value is 0, it means no waiting before disengaging.
PLC sets the servo parameter P5-89.
6-1024
15. CwPuu is where you set the number of pulses for E-CAM to wait before engaging again. The value in CwPuu
should be 32-bit and ranges from -2147483648 to +2147483647. When the value is 0, it means no waiting before
engaging again. PLC sets the servo parameter P5-92.
16. ORate is where you set the output ratio for the E-CAM chart. The value in ORate should be a 32-bit integer and
ranges from -2147000000 to +2147000000. When the value exceeds the upper or lower limit, it will be seen as the
maximum vlaue or the minimum value. PLC sets the servo parameter P5-19. For example, set ORate to 123000 and
123000 will be divided by 1000000 by the servo. And you will have 0.123 as the output ratio. Set ORate to 1500000
and 1500000 will be divided by 1000000 by the servo. And you will have 1.5 as the output ratio.
17. Once executing this instruction, it clears the Done flag first and then sends a request of setting E-CAM parameters.
If the transmission works correctly, the DONE flag is ON. If any error occurs from the slaves, the Err (error) flag is
ON. If you need to modify the E-CAM parameters, you need to wait for one scan time before executing this
instruction again.
ErrCode Description
0003 This downloading address (CAddr) or length (CLen) is NOT in the supported range.
6_
0006
6-1025
Activating E-CAM control and

2815 ECAMA Slave ~ ErrCode
displaying the status

Slave   
CAMEn    
CAMSt 
MIPuu 
SOPuu 
Err   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
INT
type
Slave  
CAMEn 
CAMSt  
MIPuu  
SOPuu  
Err 
ErrCode  

－ AS －
_6
Symbol
CAMEn ： Activate E-CAM control
CAMSt Display E-CAM status

Number of pulses inputted by the Master (unit:
MIPuu ：
PUU)
Number of pulses outputted by the specified
SOPuu ：
Slave (unit: PUU)
Err ： Error flag
6-1026
Explanation
2. The INITC and ASDON (Servo-ON) instructions must be complete before this instruction is executed.
3. Slave is a servo slave station where you can specify to receive commands; the supported slave station ranges from
1 to 8. If the slave station number you are using is out of the supported range, the instruction is NOT executed. And
the Err (error) flag is ON. If the specified servo slave station cannot communicate, the Err (error) flag is also ON.
4. CAMEn is where you can activate the E-CAM control. When the BOOL value in CAMEn is ON, it indicates E-CAM
control is activated. When the BOOL value in CAMEn is OFF, it indicates E-CAM control is NOT activated. PLC sets
the servo parameter P5-88, X=0 according to the status in CAMEn.
5. CAMSt is where you can find the E-CAM status in the servo according to the servo parameter P5-88.
S: Shows the engage status (Read-only, the setting is invalid)
0: Stop
1: Engage status
2: Pre-engage status
6_
6. Status Description:
 Stop: It is the initial status of the E-CAM. The E-CAM does not operate with the master pulse. When E-CAM
function is disabled (P5-88, X=0), it returns to this status.
 Pre-engage: When the engaged condition (path 1) is established, it enters this status. The E-CAM still does
not operate with the master pulse.
 Engage: When it reaches pre-engaged status (path 3), it enters this status. The E-CAM starts to operate with
the master pulse.
7. Path Description:
 Path 1: When the engaged condition is established (P5-88.Z), the status is Stop → Pre-engaged.
The lead pulse is determined by P5-87.
 Path 2: When the E-CAM function is disabled (P5-88.X=0), it returns to Stop status.
6-1027
 Path 3: When it is in pre-engaged status, the status is Pre-engaged → Engaged.
 Path 4: When the disengaged condition is established (P5-88, U=4), the status is Engaged → Pre-engaged.
The lead pulse is determined by P5-92 (available for FM V1.006sub04 or later).
 Path 5: When the disengaged condition is established (P5-88, U=1, 2, 6) or the E-CAM function is disabled
(P5-88, X=0), the status is Engaged → Stop.。
8. MIPuu is wherer you can find the number of pulses received by the specified Slave from the Master. The unit is per
user unit (PUU) of the servo. This value is shown accoridng to the servo parameter P5-86. When the instruction
stops, this value does NOT refreshed either.
9. SOPuu is wherer you can find the number of pulses outputted by the specified Slave. The unit is per user unit (PUU)
of the servo. This value is shown accoridng to the servo parameter CMD_O. When the instruction stops, this value
does NOT refreshed either.
ErrCode Description
0006
_6 0007 The slave is not initiated.
6-1028

Modifying the starting address for E-
2816 ECAMC Slave ~ ErrCode CAM chart and the E-CAM chart
length in the servo

Slave   
CAddr   
CLen   
Done   
Err   
ErrCode 
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
Data
type INT
Slave  
CAddr  
CLen  
Done 
Err 
ErrCode  

－ AS －
Symbol 6_
From which address to start storing E-CAM chart
CAddr ：
in the servo
CLen ： Specified E-CAM chart length for executing
Done ： Modification complete flag
Err ： Error flag
Explanation
2. This instruction is for modifying E-CAM chart settings. You need to download the E-CAM chart to the specified servo
before using this instruction.
3. Slave is a servo slave station where you can specify to receive commands; the supported slave station ranges from
1 to 8. If the slave station number you are using is out of the supported range, the instruction is NOT executed. And
the Err (error) flag is ON. If the specified servo slave station cannot communicate, the Err (error) flag is also ON.
6-1029
After modifying the E-CAM parameters and the specified servo slave station responds correctly, the DONE flag is
ON.
(error) flag is ON. PLC sets the servo parameter P5-81 (start address of data array).
5. CLen is the specified E-CAM chart length for executing; its setting range is from 5 to 720. E-CAM chart is divided
into CLen and the chart should include CLen +1 data. The servo supports 1st ~ 800th space; if the starting address is
501 and set the CLen to 400, this arrangement takes 902 (501+401) space which exceeds the 800th space, the
instruction is NOT executed and the Err (error) flag is ON. PLC sets the servo parameter P5-82. Write this
parameter when E-CAM stops (P5-88, X=0).
6. Once executing this instruction, it clears the Done flag first and then sends the modification request. After modifying
the E-CAM parameters and the specified servo slave station responds correctly, the DONE flag is ON. If any error
occurs from the slaves, the Err (error) flag is ON. If you need to modify the E-CAM starting address and length, you
need to wait for one scan time before executing this instruction again.
ErrCode Description
_6 0002 This E-CAM chart number is NOT in the supported range.
0003 This downloading address (CAddr) or length (CLen) is NOT in the supported range.
0006
6-1030
2817 D TQC Node, TarTQ, …, Err Torque control

Node   
TarTQ   
LSpeed   
CurTQ 
Reach    
Err    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Node  
TarTQ  
LSpeed  
CurTQ  
Reach 
Err 

－－ AS
Symbol
Node ： Node ID of Delta drives

6_
TarTQ ： Specified target torque
LSpeed ： Maximum speed limit
CurTQ ： Current torque value
Reach ： Target torque is reached
Err ： Communication error flag

Explanation
1. Make sure that all Delta drives have been initialized before executing this instruction.
2. For execution of this instruction, you need to use PLC FW V1.06.20 or later and ISPSoft V3.07 or later.
3. For Delta Servo Drives: set the parameter P1-01 to 3 (T: Torque Control mode) and turn the power off and on
again for the setting to be effective.
For Delta Vector Control Drives: use ASDON instruction to set Torque Control mode and set the parameter P11-33
(Torque command source) to 3 (CANopen) on Delta Motor Drives that supports torque control mode.
4. Node: the Node ID of Delta Servo Drives and Delta AC Motor Drives, ranging from 1 to 8 (Delta Servo Drives) and
21 to 28 (Delta Motor Drives). If the setting is out of the range, Err flag will be ON.
6-1031
5. TarTQ: specified target torque; it is suggested to check the manuals of Delta Servo Drives and AC Motor Drives
before setting up. You can modify the settings during the execution of this instruction.
Drive Node ID
TarTQ
Types Range
Setting the servo parameter P1-12 (internal torque limit 1), valid range: -300~+300,
unit: 1%; value exceeding the upper/lower limit will be treated as the upper/lower limit
value. The +/- sign indicates the forward / reverse direction. The servo runs according
Servo to torque control mode parameter P1-01 (torque output direction); set servo DI to
1~8
Drive TCM0 = ON and TCM1 = OFF in order to select internal torque command to 1; it is
suggested to use COPRW instruction to clear the value in servo parameter P1-12
before Power-On. Since the default value of P1-12 is NOT 0%, it will start running
once it is Servo ON.
Setting the AC motor drive parameter P11-27 (maximum torque command); index
AC
6071-00 (targeting torque) and index 6072-00 (largest output torque); valid range: -
Motor 21~28
500~+500; unit: 1%; value exceeding the upper/lower limit will be treated as the
Drive
upper/lower limit value.
6. LSpeed: maximum speed limit; this is used to prevent exceeding the speed limit, if the drives cannot complete the
specified torque commands. You can modify the settings during the execution of this instruction.
Drive Node ID
LSpeed
Types Range
_6 Servo Setting the servo parameter P1-55 (maximum speed limit); valid range 10 to rated
1~8
Drive speed of each model; unit: 1 r/min (rotary).
Setting the AC motor drive parameters

1. P01-00 = LSpeed (max. output frequency); valid range: 0~59900; unit: 0.01 Hz;
AC value exceeding the upper/lower limit will be treated as the upper/lower limit value
Motor 21~28 2. P11-37=100% (forward speed limit)
Drive 3. P11-38=100% (reverse speed limit)
You need to set parameter P11-36 (speed limit selection) to 0 and when parameter
P11-36 is set to 0, the speed limit is determined by the settings in P11-37 and P11-38.
7. CurTQ: current torque value; unit: 0.1%; the value here is the same as the value shown in its corresponding SR.
Refer to API 2803 DRVIC instruction for more details on the corresponding SR.
8. Reach is the result of the comparison between CurTQ and TarTQ, shown in 0.1% as its unit. When CurTQ >=
TarTQ, the Reach flag is ON. When CurTQ < (TarTQ – 5), the Reach flag is OFF. The delay response value is 5.
9. If the nodes of the drives respond with error messages or do not respond, PLC will set Err flag to ON. For more
details on error codes, refer to SR658 and SR659 from API 2803 DRVIC instruction.
6-1032
10. Since the values in the command of torque and speed may vary. It is suggested to check the manuals of Delta
Servo Drives and AC Motor Drives before setting up. This instruction does NOT examine or restrict if there is any
invalid value.
Example 1 (communication with Delta servo ASD-A2M)
1. Set up ASD-A2
A. Set the parameter P1-01 to 3 (T: Torque Control mode).
B. Set servo DI: TCM0 = ON and TCM1 = OFF in order to select internal torque command to 1.
If the value in DI is default value, you can set DI3 to ON and then the torque command is set by DI3 and DI4.
C. Turn the power off and on again for the setting to be effective.
2. When M1 changes from OFF to ON, the INITC instruction starts to initialize the servos at station address 1, until
SM1681 is ON.
3. When M2 changes from OFF to ON, set the servo parameter P1-12 to 0. Use COPRW instruction to write the value
in D100 into P1-12 (S3=16#210B). Remember use COPRW instruction to clear the value in servo parameter P1-12
before Power-On. Since the default value of P1-12 is NOT 0%, it will start running once it is Servo ON.
5. When M4 changes from OFF to ON, servo parameter P1-12 = 12%, servo at station address 2 moves at 1000 rpm
until M4 is OFF.
6_
6-1033
1. Set up VFD-C2000 manually
A. Set the parameter P09-36 (CANopen slave address) to range 21~28 and P09-37 (CANopen speed) to 0 (1
MHz) and P09-40 (CANopen decoding method) to 1 (Enable CANopen DS402 standard protocol).
B. Set the parameter P00-20 (source of master frequency command (AUTO)) to 6 (CANopen communication
card), P00-21 (operation command source) to 3 (CANopen communication card).
C. Set parameter P11-36 (speed limit selection) to 0 and when parameter P11-36 is set to 0, the speed limit is
_6 determined by the settings in P11-37 and P11-38.
2. When M1 changes from OFF to ON, the INITC instruction starts to initialize the AC motor drive at station address
21, until SM1683 is ON.
3. When M2 changes from OFF to ON, start torque control on the AC motor drive at station address 21.
4. When M3 changes from OFF to ON, the target torque of AC motor drive is set at 10% and AC motor drive at station
address 21 moves at the maximum output frequency of 60.00 Hz until M3 is OFF.
6-1034
6_
6-1035
2818 D TQLC Node、TarSpd、…、Err Speed of torque control

Node   
TarSpd   
LimitTQ   
CurTQ 
Reach    
Err    
DWORD
STRING
LWORD
LREAL
WORD
BOOL
REAL
UINT
DINT
LINT
TMR
CNT
INT
Data type
Node  
TarSpd  
LimitTQ  
CurTQ  
Reach 
Err 

－－ AS
Symbol：
_6 Node ： Node ID of Delta drives
TarSpd ： Specified target speed
LimitTQ ： Maximum torque
CurTQ ： Target torque is reached
Reach ： Communication error flag
Err ： Target torque is reached

Explanation
1. Make sure that all Delta drives have been initialized before executing this instruction.
2. For execution of this instruction, you need to use PLC FW V1.06.20 or later and ISPSoft V3.07 or later.
3. For Delta Servo Drives: set the parameter P1-01 to 3 (T: Torque Control mode) and turn the power off and on
again for the setting to be effective.
For Delta Vector Control Drives: use ASDON instruction to set Torque Control mode and set the parameter P00-20
(source of master frequency command (AUTO)) to 6 (CANopen communication card) on Delta Motor Drives that
supports torque control mode.
4. Node: the Node ID of Delta Servo Drives and Delta AC Motor Drives, ranging from 1 to 8 (Delta Servo Drives) and
21 to 28 (Delta Motor Drives). If the setting is out of the range, Err flag will be ON.
6-1036
5. TarSpd: specified target speed
Drive Node ID TarSpd

TarSpd
Types Range Setting Range
-60000 ~ 60000 (0.1rpm)

Servo Drive 1~8
Example: input 6005 indicating 600.5rpm The +/- sign indicates the forward /
AC Motor -32768 ~ 32767 (1rpm) reverse direction.

21~28
Drive Example: input 605 indicating 605rpm
6. LimitTQ: maximum torque value; once the instruction is started, the setting applies to the servo drive. You can
NOT modify the settings during the execution of this instruction.
Setting the servo parameter P1-12 (internal torque limit 1), valid range: -300~+300, unit: 1%; value exceeding the
upper/lower limit will be treated as the upper/lower limit value. Setting P1-02 (speed and torque (force) limit
setting); Set servo DI to TCM0 = ON and TCM1 = OFF in order to select internal torque command to 1. It is
suggested to use COPRW instruction to clear the value in servo parameter P1-12 before Power-On. Since the
default value of P1-12 is NOT 0%, it will start running once it is Servo ON. Supposing input a value of 30 in P1-12
and you will have the followings as shown in the table:
Allowable torque (force) range Forward torque (force) limit Reverse torque (force) limit
-30% ~ +30% 30% -30%
Setting the AC motor drive parameter P11-17 (forward motor torque limit Quadrant I) and P11-19 (reverse motor
torque limit Quadrant III), valid range: 0~+500, unit: 1%; value exceeding the upper/lower limit will be treated as the
6_
upper/lower limit value. Supposing input a value of 30 in P11-17 and P11-19 and you will have the followings as
shown in the table:
Setting P11-17 P11-19 Allowable torque Forward torque (force) Reverse torque (force)
Item (force) range limit limit
Value +30 +30 -30% ~ +30% 30% -30%
7. CurTQ: current torque value; unit: 0.1%; the value here is the same as the value shown in its corresponding SR.
Refer to API 2803 DRVIC instruction for more details on the corresponding SR.
8. Reach is the result of the comparison between CurTQ and TarTQ, shown in 0.1% as its unit. When CurTQ >=
TarTQ, the Reach flag is ON. When CurTQ < (TarTQ – 5), the Reach flag is OFF. The delay response value is 5.
9. If the nodes of the drives respond with error messages or do not respond, PLC will set Err flag to ON. For more
details on error codes, refer to SR658 and SR659 from API 2803 DRVIC instruction.
10. Since the values in the command of torque and speed may vary. It is suggested to check the manuals of Delta
Servo Drives and AC Motor Drives before setting up. This instruction does NOT examine or make any restrictions if
there is invalid setting or value.
6-1037
Example 1 (communication with Delta servo ASD-A2M)
1. Set up ASD-A2
A. Set the parameter P1-01 (operation mode) to 0001 (position mode)
B. Set the parameter P1-02 (speed and torque (force) limit setting) to 0010 (enabled) or use COPRW instruction
to set this parameter.
C. Set servo DI: TCM0 = ON and TCM1 = OFF in order to select internal torque command to 1.
If the value in DI is default value, you can set DI3 to ON and then the torque command is set by DI3 and DI4.
2. When M0 changes from OFF to ON, the INITC instruction starts to initialize the servos at station address 1, until
SM1681 is ON.
3. When M1 changes from OFF to ON, use COPRW instruction to set the servo parameter P1-02 (speed and torque
(force) limit setting) to 0010 (enabled).
5. When M3 changes from OFF to ON, servo parameter P1-12 = 10%, servo at station address 1 moves at 1000 rpm
until M3 is OFF.
_6
6-1038
1. Set up VFD-C2000 manually
A. Set the parameter P09-36 (CANopen slave address) to range 21~28 and P09-37 (CANopen speed) to 0 (1
MHz) and P09-40 (CANopen decoding method) to 1 (Enable CANopen DS402 standard protocol).
B. Set the parameter P00-20 (source of master frequency command) to 6 (CANopen communication card),
P00-21 (operation command source) to 3 (CANopen communication card).
2. When M1 changes from OFF to ON, the INITC instruction starts to initialize the AC motor drive at station address
21, until SM1683 is ON.
3. When M2 changes from OFF to ON, start torque control on the AC motor drive at station address 21.
4. When M3 changes from OFF to ON, the torque limit of AC motor drive is set at 10% and AC motor drive at station
address 21 moves at 1000 rpm until M3 is OFF.
6_
6-1039
6.27.3 Frequently asked questions in Delta special CANopen

communication and Troubleshooting
Question 1: After the PLC starts the INITC instruction, the initialization completion flag SM1681 is not set to ON.
Steps:
1) Make sure that Card 2 is set to AS-FCOPM communication card in AS HWCONFIG and the communication
mode is Delta special driver mode. Then check if the communication rate is the specified baud rate. After
above settings are correct, re-download the hardware configuration table and then re-check if the initialization
works. If the initialization still does not work, proceed with the next step.
2) Ensure that the servo initialization has been set by manual. Then re-power the servo on after power off. After
doing so, continue with step 3.
3) Ensure that the servo node ID (P3-00), baud rate and mode (P3-01) have been set by manual and
communication mode (P1-01) has been set to PR mode by manual. Then proceed with the step 4.
4) Ensure that the CAN communication cable connection is proper, the terminal resistor in AS-FCOPM card of
the PLC is switched on and the last servo has been connected with a terminal resistor. Then move forward to
the step 5.
5) Observe whether the word: code appears temporarily on the digital display of the servo when the PLC
enables the initialization instruction. If there is no code appearing temporarily, return to step 1 or replace the
servo. If there is the word code appearing temporarily, go to step 6.
6) Check if the actual states of DI0~DI7 (P2-10 ~ P2-17) of the servo are consistent with the function settings of
servo parameters. E.g. DI0 is the negative limit input (contact A). Check if the actual input state has been OFF
_6 (Contact B). If DI function has been enabled, make the function disabled. If the function has not been enabled,
go on with step7.
7) The communication mode of the communication card AS-FCOMP in HWCONFIG is switched back to DS301
mode. Use the CANopen Builder software to search the slave and observe which slave has not been
scanned. Remove the one which has not been scanned and then make the initialization again by adjusting the
servo node ID and the ID in INITC in the PLC.
6-1040
12
7
Chapter 7 Troubleshooting
Table of Contents
7.1 Troubleshooting ................................................................................ 7-2
7.1.1 Basic troubleshooting steps ............................................................. 7-2
7.1.2 Clear the Error States ..................................................................... 7-2
7.1.3 Troubleshooting SOP ...................................................................... 7-3
7.1.4 System Log and Positions of the Error Step ....................................... 7-4
7.2 Troubleshooting for CPU Modules ..................................................... 7-6
7.2.1 ERROR LED Indicators Are ON ......................................................... 7-6
7.2.2 ERROR LED Indicators Blinking Every 0.5 Seconds ............................. 7-6
7.2.3 ERROR LED Indicators Blinking Rapidly Every 0.2 Seconds .................. 7-8
7.2.4 ERROR LED Indicators Slow Blinking Every 3 Seconds and Lighting up for
1 Second ...................................................................................... 7-8
7.2.5 BAT. LOW LED Indicators Are ON ..................................................... 7-8
7.2.6 BAT. LOW LED Indicators Blinking Every 0.5 Seconds ......................... 7-8
7.2.7 The LED RUN and ERROR Indicators are Blinking Simultaneously
Every 0.5 Seconds ......................................................................... 7-9
7.2.8 The RUN and LED Indicators are Blinking One After Another Every
0.5 Seconds. ................................................................................. 7-9
7.2.9 Other Errors (Without LED Indicators) .............................................. 7-9
7.3 Troubleshooting for I/O Modules .................................................... 7-15
7.3.1 Troubleshooting for Analog Modules (AD/DA/XA) and Temperature
Modules (RTD/TC) .........................................................................7-15
7.3.2 Troubleshooting for the Load Cell Module AS02LC .............................7-17
7.3.3 Troubleshooting for the Module AS00SCM as a Communication Module 7-17
7.3.4 Troubleshooting for the Module AS00SCM as a Remote Module ...........7-19
7.4 Error Codes and LED Indicators for CPU Modules ............................ 7-20
7.4.1 Error Codes and LED Indicators for CPU Modules ..............................7-21
7.4.2 Error Codes and LED Indicators for Analog/Temperature Modules ........7-26
7.4.3 Error Codes and LED Indicators for Load Cell Module AS02LC .............7-27
7.4.4 Error Codes and LED Indicators for Module AS00SCM as a Communication
Module ........................................................................................7-27
7.4.5 Error Codes and LED Indicators for Module AS00SCM as a Remote
Module ........................................................................................7-28
7-1
7.1 Troubleshooting
7.1.1 Basic troubleshooting steps
This chapter includes the possible errors the can occur during operation, their causes, and corrective actions.
(1) Check the following:
 The PLC should be operated in a safe environment (consider environmental, electronic, and vibration safeties).
 Connect power supply correctly to the PLC.
 Secure the module, terminal, and cable installations.
 All LED indicators show correctly.
 Set all switches correctly.
(2) Check the following operational functions:
 Switch the RUN/STOP state
 Check the settings for the AS Series to RUN/STOP
 Check and eliminate errors from external devices
 Use the System Log function in ISPSoft to check system operation and logs
(3) Identify possible causes:
 AS Series or external device
 CPU or extension modules
 Parameters or program settings
7.1.2 Clear the Error States

Use the following methods to clear the error states. If the error source is not corrected, the system continues to show errors.
(1) Switch the CPU model state to STOP and then to RUN.
_7 (2) Turn off the CPU and turn it on again.
(3) Use ISPSoft to clear the error logs.
(4) Reset the CPU to the default settings and download the program again.
7-2
C h a p t e r 7 Tr o u b l e s h o o t i n g
7.1.3 Troubleshooting SOP

An error
occ urred
Bas ic
troub les hoot in g No Refer to s ec tion 7 .1 .1 for
Basic troubleshooti ng steps
s teps
done
Yes
Mo dule 1. Refer to s ec ti on 7 .1.4 f or the s ys tem l og
error 2. Refer to s ec ti on 7 .4 for error codes and
CP U mo d u le e r ro r L ED indic ators for CPU modules
o r mo d u le s er r or 3. Refer to s ec ti on 7 .3 for tr oubles hooting f or
I/O modules
CP U module
error
1. Refer to s ection 7 . 1. 4 for the s ys tem log
Yes 2. Refer to s ec ti on 7 .4 for error codes and
ERRO R L E D O N L ED indic ators for CPU modules
3. Refer to s ec ti on 7 .2 for tr oubles hooting f or
C PU modul es
No

E RROR L ED b li nki ng Yes 2. Refer to s ec ti on 7 .4 for error codes and
n or mal ly L ED indic ators for CPU modules
( eve ry 0 .5 se c.) 3. Refer to s ec ti on 7 .2 for tr oubles hooting f or
C PU modul es
No

ERRO R L E D b l in kin g Yes 2. Refer to s ec ti on 7 .4 for error codes and
fast L ED indic ators for CPU modules
( eve ry 0 .2 se c.) 3. Refer to s ec ti on 7 .2 for tr oubles hooting f or
C PU modul es
No

E RR O R LE D bl in k in g
sl o wl y (e ve r y 1 se c. ,
L ED indic ators for CPU modules 7_
sto p fo r 3 se c.)
C PU modul es
No

Oth er LE D b li nki ng L ED indic ators for CPU modules
C PU modul es
No
Afte r g oi ng t hr ou gh
tro ub le sho oti ng s tep s,
Yes If the p roblem per sis ts , pleas e c ontact
the i ssu es a re s til l n ot s upport.
r eso lve d.
No
The system runs normally.
7-3
7.1.4 System Log and Positions of the Error Step

If ISPSoft is connected to an AS Series, you can view actions and errors in the AS Series by clicking System Log on the
PLC menu. The CPU can store up to 20 error log sets. After the 20 sets are stored, the 1st log is replaced with the 21st if
there are new logs coming in, and the old logs are replaced with the new ones sequentially. When the memory card is
installed in the CPU module, 20 sets of the old logs are backed up in the memory card and up to 1000 logs can be recorded.
If the stored logs exceed 1000, the oldest 20 logs are replaced with the newest 20 logs in the memory card.
(1) On the PLC menu, click System Log.
(2) The System Log window appears. Click Clear Log to clear the error log in the window and the error log in the CPU
module, and reset the CPU module.
_7
 Group No.: The number 1 indicates that the error occurred in the CPU module or the right-side module 1. The
numbers 2–16 indicate the error occurred in the remote modules 1–15.
 Module No.: The number 0 indicates that the error occurred in the CPU module or the remote module. The
numbers 1–32 indicate the error occurred in the right-side module of the CPU module / remote
module. The number 1 represents the closest module to the CPU module or the remote module. This
number increases from the closest to the furthest from the CPU module or the remote module. Note:
up to eight extension modules can be connected to the right-side of the remote module.
 PLC/Module name: Model names of the CPU, remote, and extension modules.
7-4
 Error Code: Error codes in the error log.
 Date & Time: The date and time the error occurred. The most recently occurring error is listed on the top.
 The last column shows the descriptions for the error.
(3) If the operation or operand exceeds the allowed range (SM0 = ON) or an instruction inspection error (SM5 = ON)
occurs, you can use the following method to see where the problem is.
 When SM0 = ON, check the value in SR1 to see the error step. SR1: The address of the operation error (32-bit).
 When SM5 = ON, check the value in SR5 to see the error step. SR5: The address of the grammar check error
(32-bit).
 Once you know the error step number, you can go to ISPSoft -> Edit -> Step positioning. Enter the error step
number and click OK. The system takes you to the position where the step went wrong.
7_
7-5
7.2 Troubleshooting for CPU Modules

Check the LED indicators and the error codes from the CPU module and refer to the following table for troubleshooting.
V in the Log column indicates the error is recorded in the log. X in the Log column indicates the error is not recorded in
the log. H in the Log column indicates whether or not you can set recording the error in the log in HWCONFIG.
7.2.1 ERROR LED Indicators Are ON

Error
Code Description Solution Flag Log
(16#)
1. Check the setting of the watchdog timer in HWCONFIG.

000A Scan timeout SM8 V
2. Check whether the program causes a long scan time
7.2.2 ERROR LED Indicators Blinking Every 0.5 Seconds
Error
(16#)
The program in the PLC is

000C Download the program again. SM9 V
damaged.
0010 CPU memory is denied. Contact your distributor. SM9 V
CPU external memory access is
002E Contact your distributor. SM9 V
denied.
PLC programs are not consistent
002F Download the program again. SM34 V
with the system logs.
The arrangement of the function
Check whether the settings in HWCONFIG are
0070 cards is not consistent with the SM10 V
consistent with the arrangement of the function cards.
settings.
The interrupt number exceeds the
0102 SM5 X
range.
_7 The MC instruction exceeds the
0202 SM5 X
range.
The MCR instruction exceeds the Check the position where an error occurs and modify the
0302 program. Compile the program and download the SM5 X
range.
program again.
The operands used in DHSCS are
0D03 SM5 X
not used properly.
The operands HCXXX used in
0E05 SM5 X
DCNT are not used properly.
1300
Errors occurred in the remote Refer to Section 7.3.4 for more information on the error
- SM30 V
modules codes for the remote modules.
130F
The arrangement of the I/O
Check whether the settings in HWCONFIG are
1402 modules is not consistent with the SM10 V
consistent with the arrangement of the I/O modules.
settings.
More than four communication Check the total number of communication modules
140B SM10 V
modules. (maximum is four).
140D More than 32 extension modules. Check the total number of extension modules (maximum SM10 V
7-6
Error
(16#)
is 32).
More than eight remote modules on Check the total number of remote modules on the right
140E SM30 V
the right side of the CPU module. side of the CPU module (maximum is 8).
1. Make sure the module is properly connected to the
The extension module ID exceeds
1600 CPU module and turn the modules on again. SM10 V
the range.
2. If the error still occurs, contact your distributor.
The extension module ID cannot be
set.
The extension module ID is
duplicated.
The extension module cannot be
operated.
Extension module communication
timeout
1605 Hardware failure Contact your distributor. SM10 V
Settings on the communication
Make sure the function card is properly connected to the
1606 module function card are not SM10 V
CPU module and turn the modules on again.
consistant.
Check whether the external 24 V power supply to the
1607 The external voltage is abnormal. SM10 V
module is normal.
The Internal factory calibration or
1608 Contact your distributor. SM10 V
the CJC is abnormal.
1609
- Reserved (Error codes for the extension modules)
7_
160F
Check the position where an error occurs and modify the
200A Invalid instruction program. Compile the program and download the SM5 V
program again.
The number of MODBUS TCP SM
6010 Check the number of superior devices (maximum is 32). V
connections exceeds the range. 1092
The number of EtherNet/IP SM
6011 Check the number of connections (maximum is 16). V
connections exceeds the range. 1093
C000
The PLC program syntax is
- Save the PLC program and contact your distributor. - V
incorrect.
CFFF
7-7
7.2.3 ERROR LED Indicators Blinking Rapidly Every 0.2 Seconds

This happens when the power supply 24 VDC of the CPU module is disconnected, or the power supply is not sufficient,
not stable or abnormal.
Error
(16#)
Check whether the external 24 V power supply to the
002A The external voltage is abnormal. SM7 V
module is normal.
7.2.4 ERROR LED Indicators Slow Blinking Every 3 Seconds and

Lighting up for 1 Second
Error
(16#)
Connection lost in the remote
1500 Check the network connection cable. SM30 V
modules
1502
Errors occurred in the remote Refer to Section 7.3.4 for more information on the
- SM30 V
modules remote module error codes.
150F
1800
Errors occurred in the extension Refer to Section 7.3 for more information on the
- SM10 V
modules extension module error codes.
180F
1900 1. Check the CANopen connection cable.

Heartbeat errors occurred in the
- slave of the CANopen 2. Check if the specific slave is working properly. - V
Note: The last 2 digits of the error code represent the ID
191C communication module.
number of the slave (convert hexadecimal to decimal).
7.2.5 BAT. LOW LED Indicators Are ON

This happens when there is no battery (CR1620) or the power is low. Turn this option off in the HWCONFIG > CPU >
_7 Device Setting > Show Battery Low Voltage Error CPU when you don’t need the RTC function to keep track of the
current time (default is enabled).
Error
(16#)
0027 Battery Low Change battery or turn this option off SM219 X
7.2.6 BAT. LOW LED Indicators Blinking Every 0.5 Seconds

This happens when RTC cannot keep track of the current time.
Error
(16#)
RTC cannot keep track of the
0026 Contact your distributor. SM218 V
current time
7-8
7.2.7 The LED RUN and ERROR Indicators are Blinking

Simultaneously Every 0.5 Seconds
This happens when the firmware of the CPU module is being upgraded. If this happens once the power is supplied to the
CPU module, it means errors occurred during the previous firmware upgrade. Users need to upgrade the firmware again
or contact your point of purchase.
7.2.8 The RUN and LED Indicators are Blinking One After Another
Every 0.5 Seconds.
This happens when the CPU module memory card is backing up, restoring, or saving. If the CPU you are using is AS218
Series with no SD card installed, the RUN and LED indicators are blinking one after another every 0.5 seconds indicates
the AIO firmware is updating. If this happens once the power is supplied to the CPU module, it indicates the AIO firmware
updating has been failed and need to be updated again. If you did not update AIO firmware, the blinking indicates that
AIO component is abnormal and you need to contact your pointo f purchase.
7.2.9 Other Errors (Without LED Indicators)

Error
(16#)
0011 The PLC ID is incorrect. Check the PLC ID. SM34 V
0012 The PLC password is incorrect. Check the PLC password. SM34 V
The PLC maximum password attempts Reset the CPU module or restore the CPU module
002D SM34 V
exceeded. to its factory settings.
1. Reset the CPU module or restore the CPU
The memories in the latched special module to its factory settings, and then download
0050 SM6 V
auxiliary relays are abnormal. the program and the parameters again.
The latched special data registers are module to its factory settings, and then download
0051 SM6 V
abnormal. the program and the parameters again.
2. If the error still occurs, contact your distributor. 7_
The memories in the latched auxiliary module to its factory settings, and then download
0052 SM6 V
relays are abnormal. the program and the parameters again.
module to its factory settings, and then download
0054 The latched counters are abnormal. the program and the parameters again. SM6 V
2. If the error still occurs, please contact your
distributor.
The latched 32-bit counters are module to its factory settings, and then download
0055 SM6 V
The latched special auxiliary relay is module to its factory settings, and then download
0056 SM6 V
7-9

The latched data registers are module to its factory settings, and then download
0059 SM6 V
The CPU module does not detect a Check that the memory card is inserted correctly
005D SM453 V
memory card. into the CPU module.
The memory card is initialized
005E Check whether the memory card is broken. SM453 V
incorrectly.
An error occurs when data is written to Check whether the file path is correct or whether
0063 SM453 V
the memory card. the memory card is malfunctioning.
A file in the memory card cannot be Check whether the file path is correct, or whether
0064 SM453 V
read. the file is damaged.
The initialization of t CANopen 1. Check the CANopen connection cable.
communication module has not yet 2. Check if the specific slave is working properly.
1950 - V
been completed, the CANopen 3. If nothing is wrong, initialize the CANopen
instructions cannot be executed. communication module again.
1. Use the FCOMP card in the function card 2 slot
Not using the FCOMP card or not in the and make sure its work mode is CANopen
right mode for the ASDA-A2 while using communicaiton.
2001 SM0 V
the CANopen communication 2. Check the position where an error occurs and
instruction. modify the program. Compile the program and
download the program again.
The device used in the program
2003 SM0 V
exceeds the device range or it is illegal.
The operand n or the other constant
200B SM0 V
operands K/H exceed the range.
200C The operands overlap. SM0 V
The binary to binary-coded decimal
200D SM0 V
conversion is incorrect.
200E The string does not end with 00. Check the position where an error occurs and SM0 V
2012 Incorrect division operation modify the program. Compile the program and SM0 V
download the program again.
The value exceeds the range of values
2013 that can be represented by the floating- SM0 V
_7 point numbers.
The task designated by the TKON or
2014 YKOFF instruction is incorrect or SM0 V
exceeds the range.
The instruction BREAK is written
2017 SM0 V
outside of the FOR-NEXT loop.
1. Check the position where an error occurs and
No such position planning table number modify the program. Compile the program and
2027 SM0 V
or the format is incorrect. download the program again.
2. Check the settings in the position planning table.
High speed output instruction is being
Refer to SR28 for the record of the axis number and
2028 executed. Only one instruction can be - V
rearrange the output control procedures.
executed at a time.
The output frequency executed by
Modify the ratio of input and output frequency or
2030 CSFO instruction exceeds the - V
lower the input frequency.
maximum output frequency.
If the input pulse is 0 Hz and lasts for Modify the ratio of input and output frequency or
2031 - V
more than 2 seconds, PLC stops lower the input frequency.
7-10
outputting automatically.
Set the Ethernet parameter for the CPU module in

6004 The IP address filter is set incorrectly. SM1108 X
HWCONFIG again.
600D RJ45 port is not connected. Check the connection. SM1100 X
1. Check if there are devices using the same IP
There are devices using the same IP address.
6012 SM1101 V
address. 2. Check if there is more than 1 DHCP or BOOTP
server on the network.
Retry the email connection later. This error does
not cause the PLC to stop running. Solve the
6100 The email connection is busy. SM1113 X
problem by means of the related flag in the
program.
Set up the trigger attachment mode in HWCONFIG
The trigger attachment mode in the > CPU Module > Device Setting > Options >
6103 SM1113 X
email is set incorrectly. Ethernet Port Advanced > Email > Trigger Setting
> Trigger Attachment Mode.
The attachment in the email does not Check whether the attachment exists in the
6104 SM1113 X
exist. memory card.
The attachment in the email is Check the size of the attachment. If the size is over
6105 SM1113 X
oversized. 2 MB, the file cannot be sent as an attachment.
Check for the correct address and set up the
There is an SMTP server response SMTP server in HWCONFIG > CPU Module >
6106 SM1113 X
timeout. Device Setting > Options > Ethernet Port
Advanced > Email again.
1. Check whether the status of the SMTP server is
normal.
There is an SMTP server response 2. Retry sending of the email later. This error does
6107 SM1113 X
timeout. not cause the PLC to stop running. Solve the
problem by means of the related flag in the
program.
Check for the correct ID/Password and set up in
6108 SMTP verification failed HWCONFIG > CPU Module > Device Setting > SM1113 X
Options > Ethernet Port Advanced > Email again.
1. Check the program and the related special data 7_
registers.
The remote communication IP address 2. Set the Ethernet parameter for the CPU module
6200 - X
set in the TCP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Options > Ethernet Port Advanced > TCP
Socket.
1. Check the program and the related special data
registers.
The local communication port set in the 2. Set the Ethernet parameter for the CPU module
6201 - X
TCP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The remote communication port set in 2. Set the Ethernet parameter for the CPU module
6202 - X
the TCP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
7 - 11

registers.
The device from which the data is sent 2. Set the Ethernet parameter for the CPU module
6203 - X
in the TCP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The device which receives the data in 2. Set the Ethernet parameter for the CPU module
6206 - X
the TCP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The data received through the TCP 2. Set the Ethernet parameter for the CPU module
6208 - X
socket exceeds the device range. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The remote communication IP address 2. Set the Ethernet parameter for the CPU module
6209 - X
set in the UDP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Options > Ethernet Port Advanced > UDP
Socket.
registers.
The local communication port set in the 2. Set the Ethernet parameter for the CPU module
620A - X
UDP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The device from which the data is sent 2. Set the Ethernet parameter for the CPU module
620C - X
in the UDP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
_7
Socket.
registers.
The device which receives the data in 2. Set the Ethernet parameter for the CPU module
620F - X
the UDP socket function is illegal. in HWCONFIG CPU Module > Device Setting >
Socket.
registers.
The data received through the UDP 2. Set the Ethernet parameter for the CPU module
6210 - X
socket exceeds the device range. in HWCONFIG CPU Module > Device Setting >
Socket.
There is no response from the remote
6212 Make sure that the remote device is connected. - X
device after the timeout period.
6213 The data received exceeds the limit. registers. - X
2. Set the Ethernet parameter for the CPU module
7-12
in HWCONFIG CPU Module > Device Setting >

Socket.
The remote device refuses the

6214 Make sure the remote device operates normally. - X
connection.
Check whether operational sequence in the
6215 The socket is not opened. - X
program is correct.
6217 The socket is opened. - X
program is correct.
The data has been sent through the Check whether operational sequence in the
6218 - X
socket. program is correct.
The data has been received through the Check whether operational sequence in the
6219 - X
socket. program is correct.
621A The socket is closed. - X
program is correct.
1. Check the communication setting in the master
The device communication function
7011 and the slave. - H
code in COM1 is incorrect.
2. Check the communication cable.
The device communication address
used in COM1 is incorrect.
The device used in COM1 exceeds the
device range.
The device length of the communication
data in COM1 exceeds the limit.
The device checksum for the 1. Check the communication setting in the master
7017 communication serial port of COM1 is and the slave. - H
incorrect. 2. Check the communication cable.
code in COM2 is incorrect.
7_
used in COM2 is incorrect.
The device used in COM2 exceeds the
device range.
data in COM2 exceeds the limit.
7027 communication serial port of COM2 is and the slave. - H
code in the Ethernet is incorrect.
used in the Ethernet is incorrect.
7-13

The device used in the Ethernet
exceeds the device range.
data in the Ethernet exceeds the limit.
7037 communication serial port of the and the slave. - H
Ethernet is incorrect. 2. Check the communication cable.
code in the USB is incorrect.
used in the USB is incorrect.
The device used in the USB exceeds
the device range.
data in the USB exceeds the limit.
7047 communication serial port of the USB is and the slave. - H
70B1 and the slave. - H
code in function card 1 is incorrect.
used in function card 1 is incorrect.
The device used in the function card 1
_7 The device length of the communication 1. Check the communication setting in the master
70B4 data in function card 1 exceeds the and the slave. - H
limit. 2. Check the communication cable.
70B7 communication serial port of function and the slave. - H
card 1 is incorrect. 2. Check the communication cable.
70C1 and the slave. - H
code in function card 2 is incorrect.
used in function card 2 is incorrect.
The device used in function card 2
The device length of the communication 1. Check the communication setting in the master
70C4 data in function card 2 exceeds the and the slave. - H
limit. 2. Check the communication cable.
7-14
70C7 communication serial port of function and the slave. - H
card 2 is incorrect. 2. Check the communication cable.
1. Refer to the function codes defined by the
communication protocols
2. Check if the software and firmware you are using
7203 Invalid communication function code - H
is the latest versions.
3. Note down the operation procedures and the
error messages and then contact your distributor.
1. Re-editing the program and download the
program and parameters again.
The contents of the program
2. Check if the communication cables are securely
8105 downloaded are incorrect. - H
connected.
The program syntax is incorrect.
3. Save and compress the project and then send it
to your distributor.
The contents of the program 1. Re-editing the program and download the
downloaded are incorrect. program and parameters again.
8106 - H
The length of the execution code 2. Save and compress the project and then send it
exceeds the limit. to your distributor.
The contents of the program 1. Re-editing the program and download the
downloaded are incorrect. program and parameters again.
8107 - H
The length of the source code exceeds 2. Save and compress the project and then send it
the limit. to your distributor.
1. Check if the software and firmware you are using
8000 is the latest versions.
- PLC editing errors in ISPSoft 2. Note down the operation procedures and the - H
8FFF error messages and then contact your
distributor.
7.3 Troubleshooting for I/O Modules

 Introduction to troubleshotting modules
Digital I/O, analog I/O, temperature measurement, load cell, and network modules can be installed in an AS Series
system. There are 2 types of error codes; error and warning. The CPU module and its modules stop operating when 7_
errors occur. The CPU modules and its modules do not stop operating when warnings are triggered.
7.3.1 Troubleshooting for Analog Modules (AD/DA/XA) and

Temperature Modules (RTD/TC)
7.3.1.1 ERROR LED Indicators Are ON

You can set up HWCONFIG to have the following errors appear as warnings when they occur. Otherwise, when an error
occurs, only an error message appears.
Error
Description Solution
Code
16#1605 Hardware failure Contact your distributor.
16#1607 The external voltage is abnormal. Check the power supply.
The factory calibration or the CJC is
16#1608 Contact your distributor.
abnormal.
7-15
7.3.1.2 ERROR LED Indicators Blinking Every 0.2 Seconds

The following errors are specified as warnings to ensure that the CPU module can still run even when the warnings are
triggered by its modules. The following first 4 error codes are set as warnings by default in HWCONFIG; CPU must
STOP running immediately when the first 4 errors occur.
Error
Code
16#1804 The factory calibration is abnormal. Contact your distributor.
16#1807 The CJC is abnormal. Contact your distributor.
The signal received by channel 1
16#1808 exceeds the range of analog inputs Check the signal received by channel 1
(temperature).
16#1809 exceeds the range of analog inputs Check the signal received by channel 2
(temperature).
16#180A exceeds the range of analog inputs Check the signal received by channel 3
(temperature).
16#180B exceeds the range of analog inputs Check the signal received by channel 4
(temperature).
16#180C exceeds the range of analog inputs Check the signal received by channel 5
(temperature).
16#180D exceeds the range of analog inputs Check the signal received by channel 6
(temperature).
16#180E exceeds the range of analog inputs Check the signal received by channel 7
(temperature).
_7 16#180F exceeds the range of analog inputs

(temperature).
Check the signal received by channel 8
Upon power-on, the module does NOT

Check the connection between the CPU and the
- receive any detecting request from the
PLC CPU. module or reconnect them again.
7-16
7.3.2 Troubleshooting for the Load Cell Module AS02LC

You can set up HWCONFIG to have the following errors appear as warnings when they occur. Otherwise, when an error
occurs, only an error message appears.
Error
Code
16#1605 Hardware failure (that is, the driver board) Contact your distributor.

The following errors are specified as warnings to ensure that the CPU module can still run even when the warnings are
triggered by its modules. The following first 3 error codes are set as warnings by default in HWCONFIG; CPU must
STOP running immediately when the first 3 errors occur.
Error
Code
16#1807 Diver board failure Contact your distributor.
Check the signal received by channel 1 and the cable
16#1808 exceeds the range of analog inputs or the
connections.
SEN voltage is abnormal.
The signal received by channel 1 Check the value input to channel 1 and the maximum
16#1809
exceeds the weight limit. weight setting.
The factory calibration in channel 1 is
16#180A Check the weight calibration in channel 1.
incorrect.
Check the signal received by channel 2 and the cable
16#180B exceeds the range of analog inputs or the
connections.
7_
SEN voltage is abnormal.
The signal received by channel 2 Check the value input to channel 2 and the maximum
16#180C
exceeds the weight limit. weight setting.
The factory calibration in channel 2 is
16#180D Check the weight calibration in channel 1.
incorrect.
Upon power-on, the module does NOT
Check the connection between the CPU and the
- receive any detecting request from the
PLC CPU. module or reconnect them again.
7.3.3 Troubleshooting for the Module AS00SCM as a Communication

Module
7.3.3.1 ERROR LED Indicator Are ON
The following error codes identify possible errors when the AS00SCM module is installed on the right side of the CPU
module and acts as a communication module.
7-17
Error
Code
1. Check that the module is securely installed.
16#1605 Hardware failure
2. Install a new AS00SCM or contact your distributor.
1. Check if the function card is securely installed.
2. Install a new function card or contact your
distributor.
16#1606 The function card setting is not consistant.
3. Check if the setting in HWCONFIG is consistent with
the function card setting.

The following error codes identify possible errors when the AS00SCM module is installed on the right side of the CPU
module and acts as a communication module.
Error
Code
Check the parameter in HWCONFIG. Download the
16#1802 Incorrect parameters
parameter again.
1. Check whether the communication cable is
properly connected.
2. Check if the station number and the
16#1803 Communication timeout
communication format are correctly set.
3. Check if the connection with the function card is
working correctly.
1. Check the settings of the UD Link.
16#1804 The UD Link setting is incorrect.
2. Check the warning settings in the PLC.
The following error codes can only be viewed with SCMSoft; when the following errors occur, they are not shown on the
LED indicators and the system does not send the error messages to the CPU module.
Error
Code
_7 The settings in HWCONFIG and manual Check the settings in HWCONFIG and manual
16#0107 settings are not consistent with function settings for function card 1.
card 1.
The settings in HWCONFIG and manual Check the settings in HWCONFIG and manual
16#0108 settings are not consistent for function card settings for function card 2.
2.
Check the parameter in HWCONFIG. Download the
16#0201 Incorrect parameters
parameter again.
16#0301 Function card 1 communication timeout
working correctly.
16#0302 Function card 2 communication timeout
working correctly.
1. Check the UD Link settings.
16#0400 Invalid UD Link Group ID for function card 1
7-18
Error
Code
16#0401 Invalid UD Link Group ID for function card 2
16#0402 Invalid UD Link Command for function card 1
16#0403 Invalid UD Link Command for function card 1
7.3.4 Troubleshooting for the Module AS00SCM as a Remote Module

Errors from the remote modules are regarded as warnings for AS Series CPU modules. The LED indicator of the CPU
module blinks and the CPU module can still operate. Use flag SM30 to manage error presentation in the remote
modules.

Error codes:
Error
Code
1. Check if the module is securely installed.
16#1301 Hardware failure 2. Change and install a new AS00SCM or contact your
distributor.
1. Check if the function card is securely installed with
the AS-FCOPM card.
2. Change and install a new function card or contact
16#1302 The function card setting is consistant. your distributor.
3. Check if the setting in HWCONFIG is consistent
with the function card setting.
7.3.4.2 ERROR LED Indicators Blinking Every 0.5 Seconds 7_

Warning type error codes:
Error
Code
Check the network connection cable of the remote
16#1500 Remote module communication timeout
modules.
16#1502 Check the parameter in HWCONFIG. Download the

Incorrect parameters
parameter again.
16#1503 Make sure the module is properly connected to the CPU

Extension module communication timeout
module and turn the modules on again.
The actual arrangement of the extension
16#1505 module is not consistant with the Check the actual arrangement and the configuraitons.
configurations.
7-19

This happens when the 24 VDC power supply for the remote module is not sufficient. Check the power supply. If the
power supply is normal, remove the extension module from the CPU module and then check if the SCM remote module
is out of order. Error codes:
Error
Code
24VDC power supply is not sufficient and Check whether the 24 V power supply to the module is
16#1303 then recovered from low-voltage for less normal.
than 10 ms.
7.4 Error Codes and LED Indicators for CPU Modules

A. Columns
a. Error code: If an error occurs in the system, an error code is generated.
b. Description: The description of the error

c. CPU status: If the error occurs, the CPU stops running, keeps running, or shows the status you defined for the
error.
 Stop: The CPU stops running when the error occurs.
 Continue: The CPU keeps running when the error occurs.
d. LED indicator status: If the error occurs, the LED indicator is ON, OFF, or blinks.
 ERROR: System error
 Descriptions
Module Type LED indicator Descriptions

There are five types of error indicator states for of the CPU module errors,
including LED indicator ON, OFF, blinking fast, blinking normally, and blinking
slowly. When the LED indicator is ON, blinking fast/normally, clear the problems
_7
first in order to run the CPU module. When the LED indicator is blinking slowly,
indicating a warning type of error codes, it does not require immediate action.
Clear the problems when the module is powered off.
Error type:
ON: A serious error occurs in the module.
CPU Error LED Blinking fast (every 0.2 seconds): unstable power supply or hardware
Failure.
Blinking normally (every 0.5 second): system program errors or system
cannot run.
Warning type:
Blinking slowly (every one second and off for three seconds): a warning is
triggered, but the system can still run.
OFF: a warning is triggered, but the system can still run. You can modify the rules
of how a warning is triggered, or use the SM/SR to show the warnings.
7-20
7.4.1 Error Codes and LED Indicators for CPU Modules

Note: refer to Section 12.3 for the status descriptions of the Error LED indicators.
ERROR LED indicator status

Error CPU
Description
code status Blinking Blinking Blinking
ON OFF
fast normally slowly
000A Scan timeout Stop V
000C The program in the PLC is damaged. Stop V

0010 The access to the memory in the CPU is denied. Stop V
0011 The PLC ID is incorrect. Continue V
0012 The PLC password is incorrect. Continue V
RTC cannot keep track of the current time (the
0026 Continue
battery LED is blinking.)
0027 Battery low (the battery LED is ON.) Continue
24VDC power supply is not sufficient and then is
002A Continue V
recovered from low-voltage for less than 10 ms.
002D The PLC maximum password attempts exceeded. Continue V
The access to the external memory of the CPU is
002E Stop V
denied.
PLC programs are not consistent with the system
002F Stop V
logs.
The memories in the latched special auxiliary relays
0050 Continue V
are abnormal.
0051 The latched special data registers are abnormal. Continue V
The memories in the latched auxiliary relays are
0052 Continue V
abnormal.
0054 The latched counters are abnormal. Continue V
0055 The latched 32-bit counters are abnormal. Continue V
0056 The latched special auxiliary relay is abnormal. Continue V
0059 The latched data registers are abnormal. Continue V
7_
005D The CPU module does not detect a memory card. Continue V
005E The memory card is initialized incorrectly. Continue V
An error occurs when data is written to the memory
0063 Continue V
card.
0064 A file in the memory card cannot be read. Continue V
The actual arrangement of the function cards is not
0070 Stop V
consistent with the settings.
0102 The interrupt number exceeds the range. Stop V
0202 The MC instruction exceeds the range. Stop V
0302 The MCR instruction exceeds the range. Stop V
The operands used in DHSCS are not used
0D03 Stop V
properly.
The operands HCXXX used in DCNT are not used
0E05 Stop V
properly.
7-21

Error CPU
Description
ON OFF
1300
- Errors occurred in the remote modules Continue V
130F
The arrangement of the I/O modules is not
1402 Stop V
consistent with the settings.
Number of communication modules exceeds the
140B Stop V
limit of four.
Number of extension modules exceeds the limit of
140D Stop V
32.
Number of remote modules exceeds the limit of
140E Stop V
eight on the right side of the CPU module.
1500 Connection lost in the remote modules Continue V
1502
- Errors occurred in the remote modules Continue V
150F
1600 The ID of the extension module exceeds the range. Stop V
1601 The ID of the extension module cannot be set. Stop V
1602 The ID of the extension module is duplicated. Stop V
1603 The extension module cannot be operated. Stop V
1604 Extension module communication timeout Stop V
1605 Hardware failure Stop V
1606 Errors on the communication module function card Stop V
1607 The external voltage is abnormal. Stop V
The Internal factory calibration or the CJC is
1608 Stop V
abnormal.
_7 1609
- Reserved (Error codes for the extension modules) Stop V
160F
1800
- Errors occurred in the extension modules Continue V
180F
1900
Heartbeat errors occurred in the slave of the
- Continue V
CANopen communication module.
191C
The initialization of CANopen communication
1950 module has not yet been completed, the CANopen Continue V
instructions cannot be executed.
Not using the FCOMP card or not in the right mode
2001 for the ASDA-A2 while using the CANopen Continue V
communication instruction.
The device used in the program exceeds the device
2003 Continue V
range or it is illegal.
200A Invalid instruction Stop V
7-22

Error CPU
Description
ON OFF
The operand n or the other constant operands K/H
200B Continue V
exceed the range.
200C The operands overlap. Continue V
The binary to binary-coded decimal conversion is
200D Continue V
incorrect.
200E The string does not end with 00. Continue V
2012 Incorrect division operation Continue V
The value exceeds the range of values which can
2013 Continue V
be represented by the floating-point numbers.
The task designated by the TKON or YKOFF
2014 Continue V
instruction is incorrect, or exceeds the range.
The instruction BREAK is written outside of the
2017 Continue V
FOR-NEXT loop.
No such position planning table number or the
2027 Continue V
format is incorrect.
The high speed output instruction is being
2028 executed. Only one instruction can be executed at Continue V
a time.
The output frequency executed by CSFO
2030 instruction exceeds the maximum output Continue V
frequency.
If the input pulse is 0 Hz and lasts for more than 2
2031 Continue V
seconds, PLC stops outputting automatically.
6004 The IP address filter is set incorrectly. Continue V
600D RJ45 port is not connected. Continue V
The number of the MODBUS TCP connections
6010 Continue V
exceeds the range.
The number of the EtherNet/IP connections
7_
6011 Continue V
exceeds the range.
6012 There are devices using the same IP address. Continue V
6100 The email connection is busy. Continue V
The trigger attachment mode in the email is set
6103 Continue V
incorrectly.
6104 The attachment in the email does not exist. Continue V
6105 The attachment in the email is too big. Continue V
6106 There is an SMTP server response timeout. Continue V
6107 There is an SMTP server response timeout. Continue V
6108 SMTP verification failed Continue V
The remote communication IP address set in the
6200 Continue V
TCP socket function is illegal.
The local communication port set in the TCP socket
6201 Continue V
function is illegal.
The remote communication port set in the TCP
6202 Continue V
socket function is illegal.
7-23

Error CPU
Description
ON OFF
The device from which the data is sent in the TCP
6203 Continue V
The device that receives the data in the TCP socket
6206 Continue V
The data that is received through the TCP socket
6208 Continue V
The remote communication IP address set in the
6209 Continue V
UDP socket function is illegal.
The local communication port set in the UDP socket
620A Continue V
The device from which the data is sent in the UDP
620C Continue V
The device that receives the data in the UDP socket
620F Continue V
The data that is received through the UDP socket
6210 Continue V
There is no response from the remote device after
6212 Continue V
the timeout period.
6213 The data received exceeds the limit. Continue V
6214 The remote device refuses the connection. Continue V
6215 The socket is not opened. Continue V
6217 The socket is opened. Continue V
6218 The data has been sent through the socket. Continue V
6219 The data has been received through the socket. Continue V
621A The socket is closed. Continue V
The device communication function code in COM1
7011 Continue V
is incorrect.
_7
The device communication address used in COM1
7012 Continue V
is incorrect.
The device used in COM1 exceeds the device
7013 Continue V
range.
The device length of the communication data in
7014 Continue V
COM1 exceeds the limit.
The device checksum for the communication serial
7017 Continue V
port of COM1 is incorrect.
The device communication function code in COM2
7021 Continue V
is incorrect.
The device communication address used in COM2
7022 Continue V
is incorrect.
The device used in COM2 exceeds the device
7023 Continue V
range.
7024 Continue V
COM2 exceeds the limit.
7027 Continue V
port of COM2 is incorrect.
7-24

Error CPU
Description
ON OFF
The device communication function code in
7031 Continue V
Ethernet is incorrect.
The device communication address used in
7032 Continue V
Ethernet is incorrect.
The device used in Ethernet exceeds the device
7033 Continue V
range.
7034 Continue V
Ethernet exceeds the limit.
7037 Continue V
port of Ethernet is incorrect.
The device communication function code in USB is
7041 Continue V
incorrect.
The device communication address used in USB is
7042 Continue V
incorrect.
7043 The device used in USB exceeds the device range. Continue V
7044 Continue V
USB exceeds the limit.
7047 Continue V
port of USB is incorrect.
The device communication function code in function
70B1 Continue V
card 1 is incorrect.
The device communication address used in function
70B2 Continue V
The device used in function card 1 exceeds the
70B3 Continue V
device range.
70B4 Continue V
function card 1 exceeds the limit.
70B7 Continue V
port of function card 1 is incorrect.
7_
The device communication function code in function
70C1 Continue V
The device communication address used in function
70C2 Continue V
The device used in function card 2 exceeds the
70C3 Continue V
device range.
70C4 Continue V
function card 2 exceeds the limit.
70C7 Continue V
port of function card 2 is incorrect.
7203 Invalid communication function code Continue V
The contents of the downloaded program are
8105 Continue V
incorrect. The program syntax is incorrect.
8106 incorrect. The length of the execution code exceeds Continue V
the limit.
7-25

Error CPU
Description
ON OFF
8107 incorrect. The length of the source code exceeds Continue V
the limit.
8000
- PLC editing errors in ISPSoft Continue V
8FFF
7.4.2 Error Codes and LED Indicators for Analog/Temperature

Modules
Error code Description AD/

DA/ ERROR
A ↔D
16#1605 Hardware failure OFF ON
16#1607 The external voltage is abnormal. OFF ON
16#1608 The factory calibration or the CJC is abnormal. OFF ON
16#1801*1 The external voltage is abnormal. OFF Blinking
16#1802*1 Hardware failure OFF Blinking
RUN: Blinking
16#1804*1 The factory calibration is abnormal. Blinking
STOP: OFF
16#1807*1 The CJC is abnormal. OFF Blinking
The signal received by channel 1 exceeds the
16#1808
range of analog inputs (temperature).
16#1809
_7 16#180A
16#180B
range of analog inputs (temperature). RUN: Blinking
Blinking
The signal received by channel 5 exceeds the STOP: OFF
16#180C
16#180D
16#180E
16#180F
Blinking once or twice. After
Upon power-on, the module does NOT receive stops blinking for two
- OFF
any detecting request from the PLC CPU. seconds, starts the blinking
pattern all over again.
*1: The following errors are specified as warnings to ensure the CPU module can still run even when the warnings are
triggered by its AIO modules. You can set up HWCONFIG to have the following first 4 error codes appear as errors when
they occur.
7-26
7.4.3 Error Codes and LED Indicators for Load Cell Module AS02LC

AD ERROR
16#1605 Hardware failure (the diver board included) OFF ON

16#1607 The external voltage is abnormal. OFF ON
16#1801*1 The external voltage is abnormal. OFF Blinking
16#1802*1 Hardware failure OFF Blinking
16#1807*1 Diver board failure OFF Blinking
The signal received by channel 1 exceeds the range of
16#1808
analog inputs or the SEN voltage is abnormal.
16#1809 The signal received by channel 1 exceeds the weight limit.
16#180A The factory calibration in channel 1 is incorrect. RUN: Blinking
Blinking
The signal received by channel 2 exceeds the range of STOP: OFF
16#180B
analog inputs or the SEN voltage is abnormal.
16#180C The signal received by channel 2 exceeds the weight limit.
16#180D The factory calibration in channel 2 is incorrect.
Blinking once or
twice. After stops
blinking for two
Upon power-on, the module does NOT receive any
- OFF seconds, starts
detecting request from the PLC CPU.
the blinking
pattern all over
again.
*1: The following errors are specified as warnings to ensure the CPU module can still run even when the warnings are
triggered by its modules. You can set up HWCONFIG to have the following first 3 error codes appear as errors when they
occur.
7.4.4 Error Codes and LED Indicators for Module AS00SCM as a

Communication Module
7_
ON Blinking
16#1605 Hardware failure V

16#1606 The setting of the function card is incorrect. V
16#1802 Incorrect parameters V
16#1803 Communication timeout V
16#1804 The setting of the UD Link is incorrect. V
7-27
7.4.5 Error Codes and LED Indicators for Module AS00SCM as a

Remote Module

Blinking
ON Blinking
fast
16#1301 Hardware failure V
16#1302 The setting of the function card is incorrect. V
24 VDC power supply is not sufficient and then is recovered
16#1303 V
from a low-voltage less than 10ms situation.
16#1502 Incorrect parameters V
16#1503 Extension module communication timeout V
_7
7-28

DELTA IA-PLC As Manual de Programacion

Uploaded by

Copyright:

Available Formats

DELTA IA-PLC As Manual de Programacion

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DELTA IA-PLC As Manual de Programacion

Uploaded by

Copyright:

Available Formats

AS Series Programming Manual

Industrial Automation Headquarters

DACH: Delta Electronics (Netherlands) B.V.

1st The first version was published. 2 0 1 6 / 11 / 3 0

in section 1.1.2 Model Description.

1. Updated description on AS300, AS200, AS02, 04PU-A in

1.1 Overview ............................................................................................... 1-2

1.2 Software .............................................................................................. 1-10

2.1 Introduction to Devices ......................................................................... 2-2

2.2. Device Functions .................................................................................. 2-5

3.1 Types of Instructions ........................................................................ 3-2

3.2 Understanding Instruction Tables ..................................................... 3-3

3.3 Lists of Basic Instructions ................................................................. 3-7

3.4 Lists of Applied Instructions .............................................................. 3-9

Chapter 4 Instruction Structure

4.1 Applied Instructions - API Description .............................................. 4-2

4.2 Operand Usage Description ............................................................... 4-4

4.3 Restrictions on the Use of Instructions ............................................. 4-7

4.4 Index Registers ................................................................................. 4-9

4.5 Pointer Registers ............................................................................. 4-12

4.6 Pointer Registers of Timers ............................................................. 4-14

4.7 Pointer Registers for 16-bit Counters .............................................. 4-16

4.8 Pointer Registers for 32-bit Counters .............................................. 4-18

4.9 File Register .................................................................................... 4-20

Chapter 5 Basic Instructions

5.1 List of Basic Instructions ................................................................... 5-2

5.2 Basic Instructions ............................................................................. 5-3

6.1 Comparison Instructions ....................................................................... 6-4

6.2 Arithmetic Instructions ....................................................................... 6-46

6.3 Data Conversion Instructions .............................................................. 6-78

6.4 Data Transfer Instructions ................................................................ 6-121

6.5 Jump Instructions ............................................................................. 6-149

6.6 Program Execution Instructions ........................................................ 6-158

6.7 IO Refreshing Instructions ................................................................ 6-171

6.8 Miscellaneous Instructions ................................................................ 6-179

6.9 Logic Instructions .............................................................................. 6-233

6.10 Rotation Instructions ....................................................................... 6-255

6.11 Timer and Counter Instructions ....................................................... 6-267

6.12 Shift Instructions............................................................................. 6-310

6.13 Data Processing Instructions .......................................................... 6-352

6.14 Structure Creation Instructions ....................................................... 6-414

6.15 Module Instructions ........................................................................ 6-423

6.16 Floating-point Number Instructions ................................................ 6-526

6.17 Real-time Clock Instructions ........................................................... 6-562

6.18 Peripheral Instructions.................................................................... 6-594

6.19 Communication Instructions ........................................................... 6-611

6.20 Other Instructions ........................................................................... 6-703

6.21 String Processing Instructions ........................................................ 6-716

6.22 Ethernet Instructions ...................................................................... 6-780

6.23 Memory Card Instructions ............................................................... 6-822

6.25 SFC Instructions .............................................................................. 6-848

6.26 High-speed Output Instructions ...................................................... 6-856

6.27 Delta CANopen Communication Instructions ................................... 6-970

7.1 Troubleshooting ................................................................................ 7-2

1.2 Software .............................................................................................. 1-10

1.1.1 Related Manuals

 AS Series Quick Start

 AS Series Programming Manual (this manual)

 ISPSoft User Manual