Waukesha Gas Engines: GE Power & Water

GE Power & Water
Waukesha* gas engines TOPIC:

IDENT NO:
Electronic Controls
17-3093
DATE: September 2013
ESM *
SUBJECT: Updated Electronic Service Program (ESP)
SUPERSEDES: New
MODELS AFFECTED: All Waukesha gas engines with ESM
The purpose of this bulletin is to announce the release • RS-232 serial port
of an updated version of the ESP software and provide
• CD-ROM drive
instructions how to successfully download, navigate
and use the software. • Mouse or other pointing device recommended but
not required
USES / APPLICATION OF THE
SOFTWARE OBTAINING THE SOFTWARE
The Electronic Service Program (ESP) is a PC-based ESM ESP software is available by downloading the
graphic interface that provides a means of obtaining software from the GE Waukesha website or obtaining
information on system’s status and making changes to ESM ESP CD (P/N X-E001-06L). Disks can be
user adjustable setpoints. In addition, the ESP ordered though your local Distributor using this part
software provides: number.
• Log of current and historic faults DOWNLOADING ESP FROM WEBSITE TO
COMPUTER
• Detailed electronic troubleshooting (E-Help)
NOTE: Verify you have administrative rights on your
• Instruction manuals for engines using ESM computer, or have the IT department download and
• A training tool to familiarize users with the system install the program. The file will be saved as a .zip file
without being connected to an engine and will need to be extracted. Your computer will need
PKZIP or WinZip to extract the files.
• Data logging capabilities for advanced
troubleshooting 1. Log on to www.wedlink.net and select “Controls
Downloads – NEW”, located on left side of screen.
MINIMUM PC REQUIREMENTS
Make sure your PC meets the minimum system
requirements:
• Microsoft Windows XP SP2 or later operating
system environment
• Administrative rights
• 700 MHz processor
• 128 MB RAM
• 200 MB free hard disk space
• Microsoft Internet Explorer 5.0 or later
• 800 x 600 color VGA display
* Trademark of General Electric Company
Service Bulletin 17-3093

© 9/17/2013 Page 1 of 10
Service Bulletin No. 17-3093
2. Right-click on the “ESP 1.6L” link and choose “Save Target As.”
3. Save the program to a folder that allows easy RUNNING ESP INSTALLER FROM CD
access. A recommendation would be under your
The ESM ESP CD contains an installation program to
desktop, as shown below:
automatically load ESP on the hard drive of your PC.
Complete the following steps to load the ESP software
using the installation program.
1. Turn on your computer.
2. Close any other applications that may be open on
your PC’s desktop.
3. Insert the ESP CD into the CD drive of your PC.
• If Autorun is enabled on your PC system,
installation starts automatically approximately
30 seconds after the CD is inserted. Continue
with Step 7.
• If the Autorun is disabled on your PC system,
continue with Step 4.
4. From the Start menu, select Run...
4. Save the file to your computer (download time may
5. Type d:\setup.exe and click “OK” (if “D” is not the
be extensive depending on Internet speed).
letter of your CD drive, type in the appropriate
5. Open the .zip file with PKZIP or a similar extraction letter).
program.
6. See INSTALLING ESP on page 2.
6. After file is unzipped, open the folder that was
NOTE: By default, the ESP software is installed in
unzipped and run the setup.exe file.
C:\Program Files\ESM.
INSTALLING ESP
1. To start the ESP installation, run setup.exe.
7. See INSTALLING ESP on page 2.

© 9/17/2013 Page 2 of 10
2. If you have a previous version of ESP installed, 4. Read the End User License Agreement (EULA)
you will see this pop-up screen. Click “Yes” to and click “I Agree” to continue.
uninstall the older version and continue with the
installation of the new ESP program.
The older version of the ESP software will be

uninstalled. Wait for this process to complete and
for the next step to appear.
5. You are now ready to install. Click “Next” to

continue.
3. The new version of the ESP software will be

installed. Click “Next” to continue.
6. A pop-up indicating that “This computer already
has a newer version of HTML Help” appears. Click
“OK” to continue.

© 9/17/2013 Page 3 of 10
7. If a pop-up indicating that the system must be 9. Wait while files are being copied.
restarted appears, click “Cancel” to continue.
8. Wait while the program is being installed.

© 9/17/2013 Page 4 of 10
10. The ESP program has been successfully installed. Click “Finish” to complete the install.
11. Click “Close” to exit the installer.

© 9/17/2013 Page 5 of 10
12. When installation is complete, four ESP-related ESP TRAINING TOOL

icons will appear on your desktop.
The training tool allows you to view the ESP screens
DESCRIPTION ICON without an ECU connected. The training tool is
intended to allow users to become familiar with the
ESM ESP Icon: Double-clicking this screens and fields within ESP. The training tool does
icon opens the standard ESP not have the full functionality that ESP has when
program. connected to an ECU (running unit).
ESM Training Tool Icon: Double- The training tool has the code versions and
clicking this icon opens a version of workspaces to represent ECUs. When using the
ESP that is used for training only. This training tool, the user must select the proper code
program runs even without an ECU version and workspace to view the screens
connected. representative of the desired engine.
ESP Modem Access Icon: Double-
OPENING A TRAINING TOOL WORKSPACE
clicking this icon opens a version of
ESP that allows use of ESP with a 1. To run the training tool, double-click the icon
modem and requires modem cables located on the desktop.
for use.
Log File Processor Icon: Double-
clicking this icon opens a program
that converts ESP log files into a file
format read by Microsoft Excel.
2. Open “File”, then select “Open Workspace”.
ESP CD CONTENTS
DOCUMENTATION
ESP documentation is located in this directory:
C:\Program Files\ESM\Documentation
The following is available:

• ESM O&M manuals
• Spreadsheet for APG100 setup
• Readme file – see ESP TRAINING TOOL on
page 6 for more information
• S-sheets providing detailed wiring information

© 9/17/2013 Page 6 of 10
3. Select (double-click) the appropriate code version.
• The code version is easily identified on the live

engine by the icon in the upper left of the ESP
screen. The following table shows the icons for
the three most recent code versions. If the code
version is not known, select the most current:
0x44FC6077.
DESCRIPTION ICON
The ESP screen will display the

Horsepower logo if the ECU has
the 0x44FC6077 version of code
installed.

Centennial logo if the ECU has
the 0x425A587D version of code
installed.

Dresser Waukesha logo for all
previous versions of code.

© 9/17/2013 Page 7 of 10
4. Select (double-click) the appropriate workspace code in the training tool.
• Reference the ESP Training Tool Readme.txt document to determine the appropriate workspace. To
determine the proper workspace for your engine, find your engine on the list and reference the workspace
code shown on the left column.

© 9/17/2013 Page 8 of 10
5. Open the “General.wrk” workspace.
6. The training tool is now open. Select the appropriate screen by clicking on the tabs at the top of the screen. The
numbers are default values for display only. Reference the ESP programming section of one of the electronic
manuals (C:\Program Files\ESM\Documentation) of the ESP for a description of the fields.

© 9/17/2013 Page 9 of 10
REINSTALLATION – CURRENT VERSION OF ESP

• If you already have version 1.6L installed and try to reinstall version 1.6L, the following message will appear:
• If “Repair” is selected, the current ESP program will

be uninstalled and then the new ESP program will
be installed.
• If “Remove” is selected, the current ESP program
will be uninstalled and setup.exe will have to be run
again to perform the installation.

© 9/17/2013 Page 10 of 10

Waukesha Gas Engines: GE Power & Water

Uploaded by

Copyright:

Available Formats

Waukesha Gas Engines: GE Power & Water

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Waukesha Gas Engines: GE Power & Water

Uploaded by

Copyright:

Available Formats

GE Power & Water

Waukesha* gas engines TOPIC:

MODELS AFFECTED: All Waukesha gas engines with ESM

* Trademark of General Electric Company

Service Bulletin 17-3093

7. See INSTALLING ESP on page 2.

Service Bulletin 17-3093

The older version of the ESP software will be

5. You are now ready to install. Click “Next” to

3. The new version of the ESP software will be

Service Bulletin 17-3093

8. Wait while the program is being installed.

Service Bulletin 17-3093

11. Click “Close” to exit the installer.

Service Bulletin 17-3093

12. When installation is complete, four ESP-related ESP TRAINING TOOL

The following is available:

Service Bulletin 17-3093

3. Select (double-click) the appropriate code version.

• The code version is easily identified on the live

The ESP screen will display the

The ESP screen will display the

The ESP screen will display the

Service Bulletin 17-3093

4. Select (double-click) the appropriate workspace code in the training tool.

Service Bulletin 17-3093

5. Open the “General.wrk” workspace.

Service Bulletin 17-3093

REINSTALLATION – CURRENT VERSION OF ESP

• If “Repair” is selected, the current ESP program will

Service Bulletin 17-3093

You might also like