MD-II MAX

w/TK 3.74
TK 41013-1-MM (Rev. 1,10/03)

Copyright© 2000 Thermo King Corp., Minneapolis, MN, USA.

Printed in USA.
The maintenance information in this manual covers unit models:
MD-II 30 MAX (914980) MD-II 50 MAX 230/3/60 (914981)
MD-II 50 MAX 230/1/60 (914982) MD-II 50 MAX 380/460 (914983)
MD-II 30 MAX 220/3/50 EEC (914984) MD-II 50 MAX EEC 380/3/50 (914985)
For further information, refer to:
MD-II MAX Operation Manual TK 41034
MD-II MAX Parts Manual TK 41074
2.44, 2.49, 3.66, 3.74, 3.88, and 3.95 Engine Overhaul Manual TK 8312
Diagnosing Thermo King Refrigeration Systems TK 5984-7
Tool Catalog TK 5955
X214 Compressor Overhaul TK 4416
CYCLE-SENTRY IV Operation and Diagnosis TK 40288
Microprocessor Controller TG-V Operating Manual TK 40283
Set-up Manual TK 40284
In-Cab Controller Operating Manual TK 40940
The Collector Refrigeration Recovery Unit TK40956
Principals of Evacuation for Field Application TK 40612
Electrostatic Discharge Training Guide TK 40282
The information in this manual is provided to assist owners, operators and service people in the proper
upkeep and maintenance of Thermo King units.

This manual is published for informational purposes only and the information so provided should
not be considered as all-inclusive or covering all contingencies. If further information is required,
Thermo King Corporation should be consulted.

Sale of product shown in this manual is subject to Thermo King’s terms and conditions
including, but not limited to, the Thermo King Limited Express Warranty. Such terms and
conditions are available upon request. Thermo King’s warranty will not apply to any
equipment which has been “so repaired or altered outside the manufacturer’s plants as,
in the manufacturer’s judgment, to effect its stability.”

No warranties, express or implied, including warranties of fitness for a particular

purpose or merchantability, or warranties arising from course of dealing or usage of
trade, are made regarding the information, recommendations, and descriptions
contained herein. Manufacturer is not responsible and will not be held liable in contract
or in tort (including negligence) for any special, indirect or consequential damages,
including injury or damage caused to vehicles, contents or persons, by reason of the
installation of any Thermo King product or its mechanical failure.
 Recover Refrigerant
At Thermo King, we recognize the need to preserve the environment
and limit the potential harm to the ozone layer that can result from
allowing refrigerant to escape into the atmosphere.

We strictly adhere to a policy that promotes the recovery and limits

the loss of refrigerant into the atmosphere.

In addition, service personnel must be aware of Federal regulations

concerning the use of refrigerants and the certification of technicians.
For additional information on regulations and technician certification
programs, contact your local Thermo King dealer.

R-404A
WARNING: Use only Polyol Ester-based refrigeration compressor oil in
R-404A. See Thermo King Parts Manual for part number.
Do not mix Polyol Ester and standard synthetic compressor oils. Keep Polyol
Ester compressor oil in tightly sealed containers. If Polyol Ester oil becomes
contaminated with moisture or standard oils, dispose of properly–DO NOT USE.
When servicing Thermo King R-404A unit, use only those service tools certified
for and dedicated to R-404A refrigerant and Polyol Ester compressor oils.
Residual non-HFC refrigerants or oils will contaminate R-404A systems.
Table of Contents
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
General Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto Start/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
First Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Refrigeration Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
First Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Microprocessor Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Welding of Units or Truck Bodies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Engine—TK 3.74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
R-134a Refrigeration System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
R-404A Refrigeration System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Air Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electric Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electrical Standby Compressor Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Standby Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance Inspection Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Unit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
X214 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Microprocessor Controller TG-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Engine Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Electric Operation (Model 50 Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Defrost Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Unit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Unit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Protection Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Unit Photographs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Unit Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TG-V Unit Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ThermoGUARD V Microprocessor Controller (TG-V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remote Control Box Outside (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Other Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Unit Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Unit Protection Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Unit Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Pretrip Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Starting the Unit—Auto Start Diesel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Manually Starting Units on Diesel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Starting the Unit—CYCLE-SENTRY Units on Diesel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Starting the Unit—Electric Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
After Start Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Loading Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Post Load Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Post Trip Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5
Table of Contents

Electronic Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
TG-V Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Single Temp In-Cab TG-V Controller (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Display Symbols and Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Display Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
General Display Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Displaying Operating Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Entering the Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Displaying and Clearing Alarm Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Additional Operating Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Sensor Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Temperatures Outside of Display Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Guarded Access Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Testing the TG-V Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
TG-V Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Ice-Water Bath Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Sensor Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Preparing TG-V Module for Bench Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
TG-V Module Bench Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
TG-V Terminal Voltage Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
TG-V Terminal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
TG-V Terminal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
TG-V Terminal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Sensor Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Electrical Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Alternator (Prestolite) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Excessive Voltage Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Unit Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Electrical Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Charging System (12 Vdc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Preheat Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
RPM Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Glow Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Engine Reset Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Low Oil Pressure Switch (LOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Defrost Air Switch Checkout and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
High Capacity TherMaxTM Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Cool Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Heat/Condenser Evacuation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Defrost Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Start Up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
MD-II MAX Units Equipped with a Three-Phase Electric Motor and a Phase Converter
That Operates on Single-Phase Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Conversion System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Start System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Run System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Troubleshooting the Phase Conversion System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
In-Cab TG-V Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Field Test Procedure for Single Temperature In-Cab TG-V Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Connector Pins for Single Temperature In-Cab TG-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

6
 Table of Contents

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Engine Lubrication System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Engine Oil Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Engine Oil Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Oil Filter Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Crankcase Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Oil Bath Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Dry Type (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Engine Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Antifreeze Maintenance Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Checking the Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Engine Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Engine Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Bleeding the Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Draining Water from Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Fuel Filter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Electric Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Injection Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Adjust Engine Valve Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Fuel Limit Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Integral Fuel Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Electrical Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Troubleshooting the Integral Fuel Solenoid System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Fuel Stop Solenoid Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Belt Tensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Engine/Compressor Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Compressor/Electric Motor/Jackshaft Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Water Pump Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Compressor/Evaporator/Alternator and Alternator/Evaporator Fan Belts . . . . . . . . . . . . . . . . . . . . . . . . . 126
Engine Speed Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Low Speed Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
High Speed Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Refrigeration Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Set Up and Test of Evacuation Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Unit Evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Refrigerant Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Unit Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Refrigerant Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Testing the Refrigerant Charge with an Empty Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Testing the Refrigerant Charge with a Loaded Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Checking Compressor Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
High Pressure Cutout (HPCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Compressor Pump Down And Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Low Side Pump Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Three-Way Valve Condenser Pressure Bypass Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Refrigeration Service Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Commissioning Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Condenser/Radiator Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

7
Table of Contents

Refrigeration Service Operations (continued)

Liquid Line Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Dehydrator (Filter-Drier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Evaporator Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Expansion Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Cleaning In-line Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
High Pressure Cutout Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
High Pressure Relief Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Pilot Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Pressure Regulator Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Receiver Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Three-Way Valve Condenser Pressure Bypass Check Valve Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Three-Way Valve Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Compressor Pulley Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Oil Filter Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Equipment Recommendations For Use With R-404A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Hilliard Clutch Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Large Truck Unit Centrifugal Clutch Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Clutch Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Disassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Assembly Procedure (Using New Bearings and Seal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Structural Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Unit And Engine Mounting Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Lift Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Unit Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Evaporator Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Condenser Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Defrost Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Jackshaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

8
 Table of Contents

Structural Maintenance (continued)

Fanshaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Mechanical Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
CYCLE-SENTRY Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Electric Standby (Optional) Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Refrigeration Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Refrigeration Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Cool Cycle—MD-II with TherMax™ Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Condenser Evacuation Cycle—MD-II with TherMax™ Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Heat and Defrost Cycle—MD-II with TherMax™ Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Wiring and Schematic Diagrams Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

9
Table of Contents

10
List of Figures
Figure 1: Roadside View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 2: Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 3: TG-V Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 4: TG-V In-Cab Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 5: X214 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 6: X214 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7: Remote Light Indicator Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 8: TG-V Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 9: In-Range Temperature Differential Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 10: Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 11: Prestolite Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 12: Flywheel (RPM) Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 13: RPM+ and RPM- Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 14: Glow Plug Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 15: Testing Air Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 16: Air Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 17: First and Second-Phase Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 18: Motor Start Contactor Control Coil Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 19: Third Phase Connection During a Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 20: Third Phase Connection While Running Normally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Figure 21: Single Temperature In-Cab TG-V Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 22: Connecting Tester to Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Figure 23: Connector on Back of Single Temperature In-Cab TG-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 24: Engine Oil Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 25: Oil Filter Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 26: Oil Bath Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Figure 27: Dry Air Cleaner (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Figure 28: Air Restriction Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 29: Engine Cooling Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 30: Water Pump Assembly and Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Figure 31: Fuel and Oil System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 32: Electric Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Figure 33: Timing Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Figure 34: Individual Cylinder Timing and Firing Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Figure 35: Emission Control Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Figure 36: Integral Fuel Solenoid Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Figure 37: Fuel Solenoid Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Figure 38: Wiring Diagram of Fuel Solenoid Timer Starting 4th Quarter 97 . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Figure 39: Fuel Solenoid Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Figure 40: Relay Socket Terminal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Figure 41: Fuel Stop Solenoid Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Figure 42: Belt Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Figure 43: Belt Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 44: Alternator Mounting and Belt Tension Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Figure 45: Evacuation Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Figure 46: Vacuum Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Figure 47: Leak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Figure 48: Moisture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Figure 49: Unit Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Figure 50: X214 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 51: High Pressure Cutout Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 52: Install Gauge Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Figure 53: Compound Gauge Indicating 20 in. Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Figure 54: Three-way Valve Condenser Pressure Bypass Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 55: Location of Expansion Valve Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure 56: Completely Wrap Bulb with Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Figure 57: Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Figure 58: Condenser Pressure Bypass Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

11
List of Figures

Figure 59: Three-way Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Figure 60: Anti-Seize Lubricant Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Figure 61: Compressor Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Figure 62: Front View and Cross Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Figure 63: Hilliard Centrifugal Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Figure 64: Housing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 65: Bearing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 66: Bushing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Figure 67: Bushing Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Figure 68: Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Figure 69: Check Bolts For Tightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Figure 70: Lift Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Figure 71: Defrost Damper Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 72: Jackshaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 73: Installing Oil Sling Retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Figure 74: Removing Bearing Retainer Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 75: Removing Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 76: Removing Oil Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 77: Removing Roll Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 78: Installing Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 79: Installing Splash Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 80: Installing Oil Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 81: Shims and O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 82: Torquing Retainer Plate Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 83: Checking End Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 84: Fan Shaft Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Figure 85: Cool Cycle Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Figure 86: Condenser Evacuation Cycle Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Figure 87: Heat and Defrost Cycle Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

12
Safety Precautions

General Practices Auto Start/Stop

1. Always wear goggles or safety glasses.
Refrigerant liquid, refrigeration oil, and CAUTION: The unit may start
battery acid can permanently damage the eyes. automatically and at any time when the
unit On/Off switch is in the On position.
2. Never close the compressor discharge service Units with the CYCLE-SENTRYTM option
valve with the unit operating. start automatically in both
3. Never operate the unit with the compressor CYCLE-SENTRY mode and Continuous
discharge valve closed. mode. Be sure to turn the On/Off switch
Off before opening doors or inspecting or
4. Keep your hands, clothing and tools clear of working on any part of the unit.
the fans and belts when the unit is running.
This should also be considered when opening
and closing the compressor service valves.
Refrigerant
When removing refrigerant from a unit, a
5. Make sure gauge manifold hoses are in good
recovery process that prevents or minimizes
condition. Never let them come in contact
refrigerant loss to the atmosphere is required by
with a belt, fan motor pulley, or any hot
law.
surface.
When a refrigerant is exposed to the atmosphere
6. Never apply heat to a sealed refrigeration
in the liquid state, it evaporates rapidly, freezing
system or container.
anything it contacts. If refrigerant contacts the
7. Fluorocarbon refrigerants in the presence of skin, severe frostbite can result.
an open flame produce toxic gases that are
severe respiratory irritants capable of causing First Aid
death.
In the event of frostbite, the objectives of First
8. Make sure all mounting bolts are tight and are Aid are to protect the frozen area from further
of correct length for their particular injury, to warm the affected area rapidly and to
application. maintain respiration.
9. Use extreme caution when drilling holes in the • Eyes: For contact with liquid, immediately
unit. The holes may weaken structural flush eyes with large amounts of water and get
components, and holes drilled into electrical prompt medical attention.
wiring can cause fire or explosion. Holes
• Skin: Flush area with large amounts of
drilled into the refrigeration system will
lukewarm water. Do not apply heat. Remove
release refrigerant.
contaminated clothing and shoes. Wrap burns
10. Use caution when working around exposed with dry, sterile, bulky dressing to protect
coil fins. The fins can cause painful from infection/injury. Get medical attention.
lacerations. Wash contaminated clothing before reuse.
11. Use caution when working with a refrigerant • Inhalation: Move victim to fresh air and use
or refrigeration system in any closed or cardiopulmonary resuscitation (CPR) or
confined area with a limited air supply (for mouth-to-mouth ventilation if necessary. Stay
example, a truck body or garage). Refrigerant with victim until arrival of emergency medical
tends to displace air and can cause oxygen personnel.
depletion resulting in suffocation and possible
death.
12. When using ladder or scaffolding, use caution
and follow manufacturer recommendations.

13
Safety Precautions

Refrigeration Oil The following procedures must be rigidly adhered

to when servicing units to avoid microprocessor
Observe the following precautions when working damage or destruction.
with or around synthetic or polyol ester refrigerant
oil: 1. Disconnect all power to the unit.
• Do not allow refrigerant oil to contact your 2. Avoid wearing clothing that generates static
eyes. electricity (wool, nylon, polyester, etc.).
• Do not allow prolonged or repeated contact 3. Do wear a static discharge wrist strap (see
with skin or clothing. Tool Catalog) with the lead end connected to
the microprocessor’s ground terminal. These
• To prevent irritation, you should wash straps are available at most electronic
thoroughly immediately after handling equipment distributors. Do not wear these
refrigerant oil. Rubber gloves are straps with power applied to the unit.
recommended when handling polyol ester oil.
4. Avoid contacting the electronic components
First Aid on the circuit boards of the unit being
serviced.
• Eyes: Immediately flush eyes with large
amounts of water for at least 15 minutes while 5. Leave the circuit boards in their static proof
holding the eyelids open. Get prompt medical packing materials until ready for installation.
attention. 6. If a defective controller is to be returned for
• Skin: Remove contaminated clothing. Wash repair, it should be returned in the same static
thoroughly with soap and water. Get medical protective packing materials from which the
attention if irritation persists. replacement component was removed.
• Inhalation: Move victim to fresh air and 7. After servicing the controller or any other
restore breathing if necessary. Stay with circuits, the wiring should be checked for
victim until arrival of emergency personnel. possible errors before restoring power.
• Ingestion: Do not induce vomiting. Contact a 8. Never use testers consisting of a battery and a
local poison control center or physician light bulb to test circuits on any
immediately. microprocessor based equipment.
9. Before connecting or disconnecting the
Electrical Hazards battery, the Microprocessor On/Off switch
must be turned to the Off position.
Microprocessor Service
Precautions must be taken to prevent electrostatic
discharge when servicing the microprocessor
controller and related components. Potential
differences considerably lower than those which
produce a small spark from a finger to a door
knob can severely damage or destroy solid-state
integrated circuit components.

14
 Safety Precautions

Welding of Units or Truck Bodies Precautions

When electric welding is to be performed on any 1. Be certain the Unit On/Off switch is turned
portion of the temperature control unit, truck or Off before connecting or disconnecting the
truck chassis when the temperature control unit is standby power plug. Never attempt to stop the
attached, it is necessary to ensure that welding unit by disconnecting the power plug.
currents are not allowed to flow through the
2. Be certain the unit power plug is clean and dry
electronic circuits of the unit.
before connecting it to a power source.
These procedures must be rigidly adhered to when
3. When working on high voltage circuits on the
servicing units to avoid damage or destruction of
temperature control unit, do not make any
the controller.
rapid moves. If a tool drops, do not grab for it.
1. Disconnect all power to the unit. People do not contact high voltage wires on
purpose. It occurs from an unplanned
2. Disconnect all wire harnesses from the
movement.
controller.
4. Use tools with insulated handles that are in
3. Switch all of the electrical circuit breakers in
good condition. Never hold metal tools in
the control box to the Off position.
your hand if exposed, energized conductors
4. Weld unit or container per normal welding are within reach.
procedures. Keep ground return electrode as
5. Treat all wires and connections as high
close to the area to be welded as practical.
voltage until a meter and wiring diagram show
This will reduce the likelihood of stray
otherwise.
welding currents passing through any
electrical or electronic circuits. 6. Never work alone on high voltage circuits on
the temperature control unit. Another person
5. When the welding operation is completed, the
should always be present to shut off the
unit power cables, wiring and circuit breakers
temperature control unit and to provide aid in
must be restored to their normal condition.
the event of an accident.
High Voltage 7. Have electrically insulated gloves, cable
cutters and safety glasses available in the
When servicing or repairing a temperature control
immediate vicinity in the event of an accident.
unit, the possibility of serious or even fatal injury
from electrical shock exists. Extreme care must be
First Aid
used when working with a refrigeration unit that
is connected to a source of operating power, even Immediate action must be initiated after a person
if the unit is not operating. Lethal voltage has received an electrical shock. Obtain
potentials can exist at the unit power cord, inside immediate medical assistance if available.
the control box, at the motors and within the
The source of shock must be immediately
wiring harnesses.
removed by either shutting down the power or
removing the victim from the source. If it is not
possible to shut off the power, the wire should be
cut with either an insulated instrument (e.g., a
wooden handled axe or cable cutters with heavy
insulated handles) or by a rescuer wearing
electrically insulated gloves and safety glasses.
Whichever method is used do not look at the wire
while it is being cut. The ensuing flash can cause
burns and blindness.

15
Safety Precautions

If the victim must be removed from a live circuit,

pull the victim off with a non-conductive material.
Use the victim’s coat, a rope, wood, or loop your
belt around the victim’s leg or arm and pull the
victim off. Do not touch the victim. You can
receive a shock from current flowing through the
victim’s body. After separating the victim from
the power source, check immediately for the
presence of a pulse and respiration. If a pulse is
not present, start CPR (Cardiopulmonary
Resuscitation) and call for emergency medical
assistance. If a pulse is present, respiration may be
restored by using mouth-to-mouth resuscitation,
but call for emergency medical assistance.

Low Voltage
Control circuits used in the temperature control
unit are low voltage (24 Vac and 12 Vdc). This
voltage potential is not considered dangerous, but
the large amount of current available (over
30 amps) can cause severe burns if shorted or
ground.
Do not wear jewelry, watch or rings when
working on the unit. If these items contact an
electrical circuit, severe burns may result.

16
Specifications

Engine—TK 3.74
Engine TK 3.74
Fuel Type No. 2 Diesel fuel under normal conditions
No. 1 Diesel fuel is acceptable cold weather fuel
Oil Capacity:
Crankcase & Oil Filter 9 quarts (8.6 liters)
w/Bypass Oil Filter 10 quarts (9.6 liters)
Fill to full mark on dipstick
Oil Type* API Type CF-4 or CG-4 or better multigrade oil
API Synthetic Type CF-4, CG-4 or better after first 500
hours (optional)
Oil Viscosity* -15 to 40 C (5 to 104 F): SAE 15W-40
-20 to 40 C (-4 to 104 F): SAE 10W-40
-20 to 30 C (-4 to 86 F): SAE 10W-30
-30 to 30 C (-22 to 86 F): SAE 5W-30
Engine RPM:
Low Speed Operation 1625 ± 25 RPM
High Speed Operation 2425 ± 25 RPM
Engine Oil Pressure 35 to 60 psig (241 to 414 kPa)
Intake Valve Clearance 0.0079 in. (0.20 mm)
Exhaust Valve Clearance 0.0079 in. (0.20 mm)
Valve Setting Temperature Room temperature
Timing Injection Pump 14 degrees BTDC
Injection Nozzle Pressure 1700 psig (11721 kPa)
Low Oil Pressure Switch (Normally Closed) 10 ± 2 psig (69 ± 14 kPa)
High Coolant Temperature Switch:
Closes 220 ± 5 F (104 ± 3 C)
Opens 190 F (88 C)
Engine Thermostat 180 to 190 F (82 to 88 C)
Coolant System Capacity 4 quarts (3.8 liters) with overflow tank
Radiator Cap Pressure 10 psig (69 kPa)
Drive Belts to compressor, fans, 12 V alternator, water pump
and electric motor (jackshaft)
CYCLE-SENTRY Block Temperature:
Start 30 ± 18 F (0 ± 10 C)
Off 90 ± 8 F (32 ± 4.4 C)
* Multi-viscosity weight oil with the recommended API classification may be used based on the ambient temperature. The
above recommendations are written for mineral oil based lubricants.

17
Specifications

R-134a Refrigeration System

Compressor Model Thermo King X214
Refrigerant Charge 8 lb. 5 oz. (3.77 kg) R-134a
Compressor Oil Charge 66 oz. (1.95 liters)*
Compressor Oil Type Polyol Ester type (refer to Tool Catalog)
Suction Pressure Regulator Setting 18 psig (124 kPa)
Heat/Defrost Method:
Engine Operation Hot gas
Electric Operation Hot gas and electric heater strips (Model 50)
High Pressure Cutout 450 ± 10 psig (3103 ± 69 kPa)
Automatically reset @ 375 ± 38 psig (2585 ± 262 kPa)
Electronic Defrost Termination Timer:
Opens 52 F (11 C)
Closes 42 F (6 C)
Timer—Part of TG-V Microprocessor Programmable 2 to 16 hours in 2 hour increments
through TGV controller
* When the compressor is removed from the unit, oil level should be noted or the oil removed from the compressor should be
measured so that the same amount of oil can be added before placing the replacement compressor in the unit.

R-404A Refrigeration System

Compressor Model Thermo King X214
Refrigerant Charge 7.5 lb. (3.4 kg) R-404A
Compressor Oil Charge 66 oz. (1.95 liters)*
Compressor Oil Type Polyol Ester type (refer to Tool Catalog)
Suction Pressure Regulator Setting 18 psig (124 kPa)
Heat/Defrost Method:
Engine Operation Hot gas
Electric Operation Hot gas and electric heater strips (Model 50)
High Pressure Cutout 450 ± 10 psig (3103 ± 69 kPa)
Automatically reset @ 375 ± 38 psig (2585 ± 262 kPa)
Electronic Defrost Termination Timer:
Opens 52 F (11 C)
Closes 42 F (6 C)
Timer—Part of TG-V Microprocessor Programmable 2 to 16 hours in 2 hour increments
through TGV controller
* When the compressor is removed from the unit, oil level should be noted or the oil removed from the compressor should be
measured so that the same amount of oil can be added before placing the replacement compressor in the unit.

18
 Specifications

Air Switch
Air Switch Setting: 0.7 ± 0.05 in. (17.78 ± 1.3 mm) H20

Belt Tension
Tension No. on TK Gauge 204-427
New Belt Field Reset
Engine/Compressor 75 ± 3 70 ± 3
Compressor/Jackshaft (Electric Motor) 72 ± 3 67 ± 3
Compressor/Evaporator Fan/Alternator 1/2 in. (13 mm) deflection
Alternator/Evaporator Fan 1/2 in. (13 mm) deflection
Water Pump 1/2 in. (13 mm) deflection
NOTE: These are the original factory settings. Because it is difficult to use the
TK gauge 204-427 in the field, adjust each belt to allow 1/2 inch (13 mm)
deflection at the center of the longest span.
NOTE: Belts should be tensioned cold and again tensioned cold after 10 hours
of unit running.

Electrical Control System

Control System Voltage 12.5 Vdc
Alternator 12 V 65 amp brush type integral alternator
Voltage Regulator Setting 14 V @ 70 F (21.1 C)
Alternator/Regulator LED Capacitor 4.7 µfd 50 Vdc
Alternator/Output Capacitor 0.5 µfd 100 Vdc
NOTE: Disconnect components from unit circuit to check resistance.

Electrical Components
Current Draw (Amps) Resistance—
at 12.5 Vdc (Ohms)
Glow Plug 7 to 8.3 1.5 ± 0.15
Fuel Solenoid:
Pull In 30 to 40 0.41 to 0.31
Hold In 0.97 12.8
Pilot Solenoid 0.657 19
Starter Motor 90 to 105 (cranking)
Damper Solenoid 5.68 2.2
DC Circuit Breakers 50 amp 10.4
20 amp
High Speed Solenoid 5 amp (approx.) 2.5 (approx.)

19
Specifications

Thermostat
Type Solid state THERMOGUARD V Thermostat
Range -20 to 80 F (-29 to 27 C)
Heat Lockout:
Continuous Run Operation High Speed Heat locked out below 15 ± 3 F (-9.4 ± 1.7 C)
CYCLE-SENTRY Operation (Optional Equipment) All Heat locked out below 15 ± 3 F (-9.4 ± 1.7 C)
Electric Standby Operation (Optional Equipment) All Heat locked out below 15 ± 3 F (-9.4 ± 1.7 C)

Electric Standby
Electric Motor 5 hp, 230 V, 60 Hz
RPM 1750
Full Load Amps 14.4 (230)
Locked Rotor Amps 58
Power Requirements 230/3/60 30 Amp, Power Cord Size 10 (AWG) for 50’, 8 for 75’

Electrical Standby Compressor Motors

(Model 50 Units Only)
Voltage/Phase/Frequency Horse- Kilowatts RPM Full Load Locked Unit Full
power (Amps) Rotor Load*
Amps Amps
220/3/50 4.2 3.1 1450 12.7 55 12.7
230/1/60 5 3.7 1750 18 80 25
230/3/60 5 3.7 1750 14.4 58 21
460/3/60 5 3.7 1750 7.2 58 12
380/3/50 4.2 3.1 1450 7.3 55 12

* w/Heater Strips
Electric Heater Strips (Optional): Number 3
Watts (each) 750
Evaporator High Temperature Cutout Switch: Opens: 150 ± 5.0 F (66 ± 3 C)
Closes: 120 ± 5.0 F (49 ± 3 C)

Standby Power Requirements

Supply Circuit Breaker 30 amp/230 V
20 amp/460 V
Extension Cord Size Up to 50 ft—12 gauge
75 ft—10 gauge

20
Maintenance Inspection Schedule
A closely followed maintenance program will
help to keep your Thermo King unit in top
operating condition. The following general
schedule is provided to assist in monitoring that
maintenance.
Pre 750 Annual/ Inspect/Service These Items
trip Hours 3,000
Hours NOTE: The 750 hour maintenance interval may be extended to 1,000 hours
or 1 year when equipped with a bypass oil filter.
Microprocessor
• Run pretrip test (see “Pretrip Test” in the Operating Manual).
Engine
• Check fuel supply.
• • Check engine oil level.
• • • Check engine coolant level.
CAUTION: Do not remove radiator cap while coolant is hot.
• • Inspect belts for condition and proper tension.
• • Check engine oil pressure hot, on high speed. Minimum 40 psig (276 kPa) (oil
pressure gauge option).
• • • Listen for unusual noises, vibrations, etc.
• Change engine oil and filters (hot).
• Change oil bath air cleaner element, replace dry type element, clean and service
crankcase breather and check air cleaner hose for damage.
• Change fuel filter.
• Drain water from fuel tank and check vent.
• Inspect/clean fuel sediment bowl and electric fuel pump filter.
• Check and adjust engine speeds (high and low speed).
• Check condition of engine mounts.
• Maintain year round antifreeze protection at –30 F (–34 C).
— Change engine coolant every 2 years.
Electrical
• Check defrost initiation and termination.
• Check thermostat cycle sequence.
• Inspect battery terminals and electrolyte level.
• Check operation of protection shutdown circuits.
• Inspect electrical contacts for pitting or corrosion.
• Inspect wire harness for damaged wires or connections.
• Check calibration of return and discharge air sensor, and optional air sensors, in 32 F
(0 C) ice water.
• Check air switch setting.
• Inspect electric motor bearings.*
• Inspect DC (battery charging) alternator bearings* and brushes.

21
Maintenance Inspection Schedule

Pre 750 Annual/ Inspect/Service These Items

trip Hours 3,000
Hours NOTE: The 750 hour maintenance interval may be extended to 1,000 hours
or 1 year when equipped with a bypass oil filter.
Refrigeration
• • Check refrigerant level.
• • Check compressor oil level.
• • Check suction pressure regulator/throttling valve operation on Defrost or Heat.
• Check compressor efficiency and pump down refrigeration system.
• Replace dehydrator and compressor oil filter.
• Check discharge and suction pressures
Structural
• • Visually inspect unit for fluid leaks (coolant, oil, refrigerant).
• • Visually inspect unit for damaged, loose or broken parts (includes air ducts and
bulkheads, if so equipped).
• • Inspect clutch*.
• Inspect idler bearings for leakage and bearing wear.*
• Clean entire unit including condenser and evaporator coils and defrost drains.
• Check all unit, fuel tank, engine and electric motor mounting bolts, brackets, lines,
hoses, etc.
* With belt removed, spin bearings by hand. Listen for noise (bearings roll freely).

22
Unit Description

General Description The clutch engages fully at 900 ± 100 RPM on

engine operation, constantly turning the
The MD-II MAX is a one-piece, front-mount, compressor and fans at both high and low speed.
medium capacity diesel powered cooling and
heating system designed especially for straight
trucks. The unit mounts on the front of a truck X214 Compressor
with the evaporator portion protruding into the The MD-II MAX features the X214, 2 cylinder
box. Designed for use with totally chlorine free compressor with 13.92 cu. in (229 cc)
R-404A refrigerant. An optional R-134a unit is displacement.
also available. There are two basic models:
MD-II MAX Model 30: Cooling and heating on Microprocessor Controller
engine operation. TG-V
MD-II MAX Model 50: Cooling and hot gas Thermo King has applied the newest
heating on engine operation and electric standby technological advances to develop a
electric evaporator heaters are optional. programmable microprocessor controller that
Power to the system is provided by a Thermo controls unit functioning and displays operating
King TK 3.74, water-cooled, 3 cylinder diesel information quickly and accurately.
engine rated at 11.2 continuous horsepower Features include:
(8.35 kW) at 2400 RPM. A belt drive system Thermometer: Displays return air temperature
transfers power to the compressor, unit fans and with 0.1 degree accuracy.
alternator.
Thermostat: Provides temperature control from
Electric standby power (Model 50) is provided by -20 to 80 F (-28 to 28 C), in 0.5 degree
a 5 horsepower electric motor. A clutch on the increments.
diesel engine isolates the engine during electric
Defrost Control: If the evaporator coil temperature
standby operation.
is below 42 F (6 C), Defrost is automatically
Belt driven, dual evaporator fans provide superior initiated every 4 hours during pulldown until the
air throw. Exclusive space condenser provides return air temperature is in-range. At in-range
maximum cab clearance and reduced truck body temperatures (between approximately 7 degrees
height on conventional chassis. Cube saver above and 7 degrees below setpoint), the
evaporator optimizes space below the evaporator controller is programmable for 2 to 16 hours in 2
for all types of cargo. Lightweight aluminum hour increments. The Defrost interval is set at the
frame allows increased payload. factory, but can be reprogrammed by your
The MD-II MAX operates under the control of a Thermo King dealer.
TG-V microprocessor controller. The built-in Fuel Saver: Can be programmed to delay high
microprocessor controller simplifies system speed operation for optimum fuel economy.
monitoring and troubleshooting. TherMax™ Alarm: Can detect and display alarm conditions
defrost/heating system increases unit heating including sensor, microprocessor and defrost
capacity for faster defrost. termination failures.
The built-in CYCLE-SENTRY, an exclusive The TG-V Controller is programmed to lock out
Thermo King feature, automatically starts and High Speed Heat if set below 15 F (-9.4 C).
stops the unit according to temperature demands.
Cab Control Box: The Cab Control Box allows the
In addition, a range of programmable modes, like
high speed pull-down, allow you to tailor your driver to control and monitor some of the unit
unit’s performance to the load you are functions from inside the cab. The auto start
distributing. system controls the preheat, run, and start relays
to automatically start the unit when all On/Off
switches are in the On position.

23
Unit Description

Refer to the Operating Instructions for detailed With the Auto Start/Stop-Continuous Run switch
description of the controller functions. in the Auto Start/Stop position, the
CYCLE-SENTRY system starts the unit on
Operating Modes thermostat demand and shuts down the unit when
the box temperature reaches the thermostat
The MD-II MAX uses a ThermoGUARD V setpoint.
microprocessor controller for operational control
of the unit. On CYCLE-SENTRY equipped units, unit
start-ups may also be initiated by Defrost cycle
Engine Operation initiation or engine block temperature thermostat
demand. In cold ambients, the CYCLE-SENTRY
Continuous Run Operation system demand automatically maintains engine
temperature by restarting the unit if the engine
When the unit is started with the box temperature block temperature drops to 30.0 F (0 C). When the
higher than 3.4 F (1.9 C) above the thermostat unit starts because of low engine block
setpoint, the unit will run on High Speed Cool. temperature, it will run in the operating mode
When the temperature drops to 3.4 F (1.9 C) called for by the unit thermostat until the battery
above setpoint, the thermostat de-energizes the is fully charged and the engine block temperature
High Speed engine solenoid circuit, placing the reaches 90.0 F (32.2 C)
unit on Low Speed Cool. After the unit starts, a Battery Sentry module
When the box temperature reaches the thermostat monitors the voltage across the field of the
setpoint, the pilot solenoid is energized. The alternator and will keep the unit running if the
three-way valve shifts to the Heat position, battery is not sufficiently recharging. The
placing the unit on Low Speed Heat. ThermoGUARD thermostat controls unit
operating mode to maintain the box temperature
If the temperature continues to fall, the thermostat thermostat setpoint. The unit runs in whichever
will shift the unit to High Speed Heat at 3.4 F operating mode the thermostat is calling for to
(1.9 C) below setpoint. The unit will remain on properly maintain the box temperature.
High Speed Heat until the box temperature rises
to 1.7 F (0.9 C) below setpoint. Electric Operation (Model 50 Units)
If the temperature continues to rise to 1.7 F When the unit switch is turned On with the box
(0.9 C) above setpoint, the thermostat temperature higher than 3.4 F (1.9 C) above
de-energizes the pilot solenoid. The three-way thermostat setpoint, the unit will run on Cool.
valve shifts back to the Cool position, placing the
unit on Low Speed Cool. When the temperature drops to setpoint, the
thermostat de-energizes the electric motor
If the temperature continues to rise to 5.1 F contactor, placing the unit on Null.
(2.9 C) above setpoint, the thermostat will
energize the engine solenoid high speed circuit, If the box temperature continues to fall, the
placing the unit on High Speed Cool. thermostat energizes both the electric motor
contactor and the heat contactor (optional) to
CYCLE-SENTRY Operation (Optional) place the unit on Heat at 3.4 F (1.9 C) below
setpoint. The unit will remain on Heat until the
WARNING: With the selector switch in box temperature rises to 1.7 F (0.9 C) below
the Auto Start/Stop position and unit setpoint. The thermostat will then de-energize the
On/Off switch in the On position, the unit electric motor contactor and optional heat
may start at any time without prior contactor, placing the unit on Null.
warning.
If the temperature continues to rise to 5.1 F
(2.9 C) above setpoint, the thermostat will
energize the electric motor contactor, placing the
unit on Cool.

24
 Unit Description

Defrost Operation • 23 Ampere Alternator

The Defrost mode can be initiated any time the • Defrost Timer (Part of TG-V)
evaporator coil temperature is below 42.0 F
• Air Defrost Switch
(5.6 C). Defrost is initiated automatically by the
defrost air switch and defrost timer or manually • Electronic Engine Hourmeter
by pressing the Manual Defrost switch.
• Alternator Discharge Light
When a Defrost cycle is initiated, the defrost relay
• Digital Thermometer (Part of TG-V)
energizes the damper solenoid and pilot solenoid.
• TherMax™ Defrost/Heating System
The unit remains on Defrost until the evaporator
coil temperature rises to 52.0 F (11.1 C), causing • R-404A.
the defrost termination switch to open. When the
defrost termination switch opens, the unit may Unit Options
shift back to the Cool or Heat mode, or the Null
mode (optional Start/Stop operation). • Electric Standby Motor (Model 50)
If the thermostat calls for the Null mode (optional • CYCLE-SENTRY Start/Stop Controls
Start/Stop operation) while the unit is defrosting, • Remote Control Box (outside, beneath unit)
the unit will continue to run until defrosting is
complete. Then the unit will stop. • In-Cab w/TG-V
• Hourmeter, Electric Operation (Model 50)
Serial Number Locations • Dry-type Air Cleaner
Unit: Nameplate on top of roadside of the unit
frame above the switch panel. • Fuel Heater
Engine: Nameplate on top of the rocker arm cover. • Ammeter
Compressor: Stamped on the side below the sight • Silicone Coolant Hoses
glass.
• Oil Pressure Gauge
Electric Motor: Nameplate attached to the motor
housing. • Remote Indicator Lights
• Top Screen
Unit Features • Engine Coolant Temperature Gauge
• TK 3.74 Diesel Engine • Suction Pressure Gauge
• X214 Compressor • Electric Heaters
• ThermoGUARD V Microprocessor Controller • Spin-on Bypass Oil Filter
• Tapered Roller Bearing Fanshaft & Idler • R-134a.
• Heavy Duty Oil Bath Air Cleaner
• Three-way Valve Refrigeration System
• One-piece Main Wiring Harness
• Spin-on Fuel Filter
• Spin-on Full Flow Oil Filter
• Electric Fuel Pump
• Coolant Expansion Tank with Coolant
Indicator

25
Unit Description

Protection Devices
• Engine Coolant High Temperature Cutout
Switch
• Engine Low Oil Pressure Cutout Switch
• Evaporator High Temperature Cutout Switch
(Model 50 only) with Heater Option
• Refrigerant High Pressure Cutout
• Refrigerant High Pressure Relief Valve
• 20 Ampere Circuit Breaker in Control Circuit
• 12 V Fuse Link (50 Ampere) (Current
Limiter)
• Overload Relay Protection for Electric
Standby Motor (Model 50)
• 50 Ampere Circuit Breaker in Starting Circuit.

26
 Unit Description

Unit Photographs

Figure 1: Roadside View

27
Unit Description

5 6 7 8 9

4 10

11
3

12

15 14 13

1. Fuel Filter 9. High Pressure Relief Valve

2. Oil Filter 10. Receiver Tank
3. Engine 11. Air Defrost Switch
4. Muffler 12. Drier
5. Suction Pressure Regulator 13. Condenser Coil
6. Compressor 14. Three-Way Valve
7. Alternator 15. Expansion Tank
8. Nameplate

Figure 2: Top View

28
 Unit Description

1 2 3

4 12

14
13

11 10 9 8

1. Motor Reset (Model 50) 8. On/Off Switch

2. Engine Reset 9. Preheat/Start Switch
3. Auto Start/Stop - Continuous Run 10. Manual Defrost Switch
Switch (Optional)
4. Start/Stop Light (Optional) 11. Microprocessor Controller TG-V
5. Defrost Light 12. Run Hourmeter (Optional on Model 50)
6. Engine Light 13. Engine Hourmeter
7. DC Alt Light 14. Electric Operation Hourmeter (Optional
on Model 50)

Figure 3: TG-V Control Panel

29
Unit Description

1 2 3 4 5 6

10 9

1. Temperature Display 6. UP Key

2. Power Cord Indicator Light 7. DOWN Key
3. ON Key 8. DEFROST Key
4. OFF Key 9. ENTER Key
5. SELECT Key 10. LOW NOISE Key

Figure 4: TG-V In-Cab Controller

30
 Unit Description

AEA04

1. Oil Seal (Location Not Shown) 4. Cylinder Head

2. Crankshaft 5. NOTE: Apply Thread Sealant When
Installing High Pressure Cutout.
3. Discharge Port

Figure 5: X214 Compressor

31
Unit Description

8
9
5

10

3
11

2
AEA05

1. Oil Drain Plug 7. Cylinder Head

2. Oil Pump Cover 8. Crankshaft
3. Pressure Regulator Assembly 9. Oil Fill Plug
4. Oil Pump Gauge Access 10. Sight Glass
5. Suction Port 11. Serial Number
6. Suction Valve Adapter

Figure 6: X214 Compressor

32
Operating Instructions
Start/Stop Light (Optional): When this green light
WARNING: Do not operate the unit until
is On, the CYCLE-SENTRY system is
you are completely familiar with the
functioning normally. A malfunction is indicated
location and function of each control,
if the Auto Start/Stop-Continuous Run Switch is
gauge and indicator on the panels.
set to Auto Start/Stop and the light is off. In this
situation, the unit will not run. The Engine Reset
Unit Controls may be tripped.
Engine Reset: The Engine Reset is a pushbutton
TG-V Unit Control Box switch behind a flexible weatherproof cap. When
Auto Start/Stop - Continuous Run Switch this switch “opens”, the button pops out. It
(Optional): This switch selects Continuous Run remains open until it is manually pushed in to
operation or CYCLE-SENTRY operation. reset the circuits.
• Cont. Run position: The unit will be started When the Engine Reset is open (tripped), the
manually with the On/Off switch and the diesel engine cannot be started. If the reset trips
Preheat/Start switch. After start-up, the unit while the engine is running, the engine will
operates continuously until the On/Off switch shutdown. Four conditions can cause the engine
is turned Off or a protection circuit shutdown reset to trip:
occurs due to a malfunction in the fuel, engine
oil, engine coolant or refrigeration system. • Engine oil pressure drops below 7 to 13 psi
(48 to 90 kPa) while the On/Off switch is
• Auto Start/Stop position: All unit starting switched to On. This includes any situation
operations are performed automatically on which causes the engine to stop or not start
demand. Starting functions such as glow plug within a short period of time.
preheat, fuel and throttle solenoid control and
cranking are performed automatically when • Engine coolant temperature rises above 215 to
operation is required. The engine will start 225 F (102 to 107 C).
automatically for one or a combination of the • Engine oil pressure drops too low.
following conditions:
• The starter exceeds the cranking limit in
a. The Microprocessor Controller calls for CYCLE-SENTRY operation (optional).
heating or cooling.
Some situations which may cause the Engine
b. Manual Defrost initiated. Reset to open are:
c. Engine block temperature drops below a. Engine runs out of fuel.
35 F (2 C).
b. On/Off switch is left On accidentally
Once started, the engine will run until: without the engine being started.
a. Microprocessor Controller demands are c. Engine does not start after cranking in
satisfied, CYCLE-SENTRY mode.
b. The block temperature reaches 90 F d. High refrigerant pressure causes the high
(32 C), pressure cutout to stop the engine.
c. The Defrost cycle is complete. Defrost Light: When this orange light is On, the
The engine is then automatically stopped by unit is operating in the Defrost mode.
the CYCLE-SENTRY control system. Engine Light: When this red light is On, the
Engine Reset switch has been tripped.

33
Operating Instructions

DC Alt Light: When this yellow light is On, there Ammeter (Optional): The Ammeter indicates
is no current output from the alternator. whether the battery is being charged or
On/Off Switch: This switch supplies power to the discharged. The amount of discharge shows
circuits of the unit. whether the glow plugs are functioning properly
during preheat.
• On position: This switch energizes the
electrical system for the unit. ThermoGUARD V Microprocessor
• Off position: This switch de-energizes the Controller (TG-V)
electrical system and the unit will not operate. WARNING: Do not operate the TG-V
NOTE: If the unit is also equipped with an until you are completely familiar with the
In-Cab Control Box. All On/Off switches must meaning of each display symbol, and the
be in the On position before the unit will operate. function of each control key.
Preheat/Start Switch: When held on Preheat, this The programmable TG-V displays temperature
switch energizes the glow plugs in the diesel and alarm conditions. It also functions as a
engine to aid in starting. thermostat and a defrost timer for the unit.
When held on Start, this switch energizes both the The TG-V In-Cab Remote Control Box provides
glow plugs and the starter which cranks the convenient on-the-road unit control from inside
engine. the truck cab. It includes the following:
Manual Defrost Switch: When pushed, the Manual Temperature Display: This digital temperature
Defrost switch starts the Defrost cycle. However, display indicates the temperature of the air
the evaporator coil must be below 42 F (6 C) for returning from the cargo box to the evaporator.
the unit to go into Defrost. A thermal switch on Power Cord Indicator Light (Model 50): When this
the evaporator coil senses this temperature. red light is On, the Electric/Diesel switch is in the
NOTE: The unit will remain in Defrost mode Electric Standby position and the truck ignition is
until the coil temperature rises to 52 F (11 C). on.
Run Hourmeter (Optional on Model 50): The Run OFF Key: Used to turn off the controller and stop
Hourmeter records the total number of hours that the engine or standby motor.
the unit has been in operation. ON Key: Used to turn on the condensing unit and
Engine Hourmeter: The Engine Hourmeter records the controller.
the total number of hours that the diesel engine NOTE: The main unit On/Off switch must be set
has been in operation. This meter can be used to to On before the In-Cab Controller can be
determine proper maintenance intervals. turned On. The unit will automatically start.
Electric Operation Hourmeter (Optional on Model Also, the In-Cab Controller must be On before
50): The Electric Operation Hourmeter records the the main unit can be started.
total number of hours that the electric motor has
SELECT Key: Used to select the various displays
been in operation. This meter can be used to
which can appear on the screen.
determine proper maintenance intervals.
UP Key: Used to increase setpoint temperature
Coolant Temperature Gauge (Optional): The
when the setpoint symbol is on the screen.
Coolant Temperature Gauge indicates the
temperature of the coolant in the engine block. DOWN Key: Used to decrease setpoint temperature
when the setpoint symbol is on the screen.
Oil Pressure Gauge (Optional): The Oil Pressure
gauge shows the engine oil pressure. This DEFROST Key: Used to start the Defrost cycle of the
pressure should rise immediately after the engine evaporator.
starts. ENTER Key: Used to enter new information into the
Suction Pressure Gauge (Optional): The Suction controller.
Pressure gauge indicates the pressure of the
refrigerant gas returning to the compressor.

34
 Operating Instructions

NOTE: The ENTER key must be pressed within 6 Remote Control Box Outside
seconds after releasing the UP or DOWN key to (Optional)
complete the setpoint change.
The switches in the remote control box energize
LOW NOISE Key: Used to lock out high speed relays on the option board to control the operation
operation to maintain low speed (low noise) of the unit. The remote On/Off switch and the unit
operation. On/Off switch must both be in the On position for
With the unit switched off, the controller screens the unit to operate. Either switch will turn the unit
will be dark; nothing will be on the display. When off.
the unit is switched On, all symbols and readouts The remote control box mounts on the truck body
will be displayed for about 10 seconds. Make sure beneath the unit to offer easier accessibility to unit
that all display segments are operational. controls. This box offers the following functions:
Standard Display is set to Return Air Temperature Preheat/Start Switch: When pressed to Preheat,
at the factory. Each controller can be programmed the switch energizes the glow plugs to aid in
to show return air or setpoint as the Standard starting. When pressed to Start, it energizes both
Display. the glow plugs and the starter motor.
When unit is switched off, it is normal for display On/Off Switch: The On/Off switch energizes the
to remain On for about 30 seconds. On relay, activating the unit electrical system. The
control panel On/Off switch and the remote
With power off or battery disconnected, all On/Off switch must both be On in order for the
settings are saved in the controller memory and unit to operate. Either switch can stop the unit.
become active when unit is switched On.
Manual Defrost: Pressing the Manual Defrost
During the normal operation, the Standard switch will initiate a Defrost cycle if the
Display is on the screen. evaporator coil temperature is below
Return Air Temperature is factory Standard 42.0 F(5.6 C).
Display setting (can be changed). Other operating Diesel/Electric Switch (Model 50 only): Switches
data can be displayed. the unit to electric motor standby power when
placed in Electric position and power cord is
To view other operating data, repeatedly press and
connected to the box.
release the SELECT key.
The following data may be displayed: Other Controls
• Discharge Air Temperature Defrost Termination Switch: A temperature
• Setpoint Temperature sensitive switch is mounted on the evaporator
coil. It is used to control Defrost. The switch
• Press SELECT key for next display. closes when the evaporator temperature drops to
The remote control box is replaced with an 42 F (6 C). This enables Defrost.
electric standby power receptacle on units that are Defrost Air Switch: The Defrost Air switch senses
equipped with the cab control box. the air pressure difference between the evaporator
coil inlet and outlet. The switch automatically
places the unit on Defrost when the evaporator
temperature is below 42.0 F (5.6 C) and frost
builds up on the coil to a point where the air flow
across the coil is restricted.

35
Operating Instructions

Unit Indicators Hourmeters: The hourmeter records the number of

hours the unit is in diesel operation for proper
Remote Light Indicator Box (Optional): The
maintenance intervals. An electric hourmeter
optional Remote Light Display mounts on the (hours in electric operation) and a total hourmeter
truck for convenient indication of the unit’s (total operating hours) are optional equipment.
operating mode. The following conditions are
indicated by the respective light(s) being On: Digital Thermometer: A digital thermometer is
built into each thermostat. The thermometer
a. Cool (White). The unit is cooling. normally indicates the return air temperature.
b. Defrost (Tan). The unit is defrosting. Receiver Tank Sight Glass: This sight glass is used
c. Heat (Amber). The unit is heating. to check the amount of refrigerant in the system.
Compressor Oil Sight Glass: The compressor oil
d. High Speed (Blue). When the blue light
sight glass indicates the relative level of
and white light are On at the same time,
compressor oil in the compressor sump.
the unit is in high speed cool. When the
blue light and amber light are On at the Engine Oil Dipstick: Use the engine oil dipstick to
same time, the unit is in High Speed Heat. check the engine oil level.
Coolant Tank: This gauge indicates the engine
e. CYCLE-SENTRY (Green). The unit is in
CYCLE-SENTRY mode. coolant level. If the pointer is in the FULL (white)
range, the coolant level is acceptable. If the point
f. Fuel Saver (Light Blue). Not used. is in the ADD (red) range, add coolant to the
g. Check Light (Orange). Not used. expansion tank.

h. In Range (Blue/Green). Not used. CAUTION: Do not remove expansion

tank cap while the coolant is hot.

Unit Protection Devices

Engine Reset Switch: A thermal type manual reset
switch protects the engine. The reset switch
contains a heater coil that is attached to a sensor
1
switch in the engine oil system, engine coolant
2
system and the (optional) CYCLE-SENTRY
3 system.
4
5
When the engine oil pressure is too low, when the
starter exceeds the cranking limit on Auto
6
Start/Stop operation, or when the engine coolant
7
temperature is too high, the coil in the reset switch
8 begins to heat up. In 20 to 40 seconds, the switch
1. Cool Light
will open and shut down the unit. To reset the
engine reset, press the engine reset button.
2. Defrost Light
Overload Relay/Electric Motor Reset Switch
3. Heat Light (Model 50): The overload relay protects the
4. High Speed Light electric standby motor. The overload relay opens
5. CYCLE-SENTRY Light
the circuit from the linestarter to the electric motor
if the motor overloads for any reason, (e.g., low
6. Fuel Saver Light (Not Used) line voltage or improper power supply) while the
7. Check Light (Not Used) unit is on Electric Standby operation. To reset the
8. In Range Light (Not Used) electric motor, press the motor reset button which
is located on the high voltage box.
Figure 7: Remote Light Indicator Box

36
 Operating Instructions

Control System Circuit Breaker: The control Preheat Buzzer (CYCLE-SENTRY Units): The
system remote reset circuit breakers are located in preheat buzzer sounds when the
the control box. They are designed to protect the CYCLE-SENTRY system causes the glow plugs
12 volt DC control circuit from overloads. To to preheat.
reset the circuit breakers, turn the unit On/Off
switch to the Off position for 30 seconds. Unit Operation
Control Circuit Fuse: Located between the battery
and the unit control circuits (typically inside the Pretrip Inspection
battery box). At about 60 amps, the fuse will melt
Pretrip inspections are a very important part of
and cut battery power to the unit.
regularly scheduled preventive maintenance
Engine Coolant High Temperature Cutout: The programs designed to minimize operating
engine coolant high temperature cutout is a problems and breakdowns before they happen.
temperature sensitive switch located in the engine While pretrips are not intended to take the place
cooling system. of regular maintenance inspections, the following
The engine coolant high temperature switch will suggested pretrip inspection should be performed
close and trip the engine reset if the engine before every trip involving refrigerated cargo.
coolant temperature is greater than 215 to 225 F Fuel: The diesel fuel supply must be adequate to
(102 to 107 C). guarantee the operation of the engine to at least
Evaporator High Temperature Protection Switch
the next check point.
(Model 50): A high temperature protective switch Engine Oil: The
engine oil level should be at the
is located above the evaporator coil to interrupt FULL mark on the dipstick. Never overfill.
the Heat cycle if the temperature above the coil
Coolant: Check coolant level gauge for the correct
exceeds 150 F (66.0 C) during electric standby
amount of coolant. The indicator should be in the
operation.
FULL (white) range. If the coolant level is in the
Engine Low Oil Pressure Cutout: The engine low ADD (red) range, add coolant to the expansion
oil pressure cutout is a pressure sensitive switch tank. The coolant should be a 50/50 mixture of
located in the engine oiling system. This switch ethylene glycol and water and provide protection
will trip the Engine Reset and stop the engine if to -30 F (-34 C).
the oil pressure drops below 8 to 12 psi
(55 to 83 kPa). CAUTION: Do not remove the expansion
Refrigerant High Pressure Cutout: The high tank cap while the coolant is hot.
pressure cutout is a pressure sensitive switch
Battery: The terminals must be tight and free of all
located in the compressor head. If the refrigerant
discharge pressure exceeds the current setting, corrosion. Electrolyte should be at full mark.
this switch opens the circuit to the fuel solenoid, Belts: The belts must be in good condition and
stopping the engine. Within 30 to 50 seconds, the adjusted to the proper tension. Allow 1/2 inch
engine reset will also trip because of low oil (13 mm) deflection at the center of the span
pressure in the engine. For Model 50 units, this between pulleys.
switch also shuts down electric motor operation. Electrical: Check all electrical connections to
Refrigerant High Pressure Relief Valve: This valve make certain they are securely fastened. Wires
is designed to relieve excess pressure within the and terminals should be free of corrosion, cracks
refrigeration system. Located on a high pressure or moisture.
line near the condenser, it is non-repairable and Structural: Visuallyinspect the unit for leaks,
requires no adjustment. When pressure is released loose or broken parts and other damage.
from the valve, it is directed away from anyone
servicing the unit. Gasket: The unit mounting gasket should be
tightly compressed and in good condition.
Coils: The condenser and evaporator coils should
be clean and free of debris.

37
Operating Instructions

Cargo Box: Inspect the interior and exterior of the Manually Starting Units on Diesel
box for damage. Any damage to the walls or Operation
insulation must be repaired.
1. Place the Diesel/Electric switch in the Diesel
Defrost Drain: Check the defrost drain hoses and position and place the power receptacle
fittings to be sure they are open. On/Off switch in the On position.
Doors: Be sure doors and weather seals are in 2. Hold the Preheat/Start switch in the Preheat
good condition, door latches securely and weather position for the required time.
seals fit tightly.
Ambient Temperature Preheat Time
Starting the Unit—Auto Start Diesel
32 to 60 F (0 to 16 C) 30 seconds
Operation
0 to 32 F (-18 to 0 C) 60 seconds
Auto Start is included with the cab control box.
Below 0 F (-18 C) 90 seconds
1. Place the Diesel/Electric switch in the Diesel
position and place the power receptacle
3. Place the control box On/Off switch in the On
On/Off switch in the On position.
position.
2. Place the control box On/Off switch in the On
4. Press the ON key in the cab control box.
position.
5. Hold the Preheat/Start switch in the Start
3. Press the ON key in the cab control box.
position to crank the engine. Release when the
4. The unit should preheat and start engine starts. Do not release the switch
automatically. If the unit fails to start, press prematurely when the engine is extremely
the OFF key and place the On/Off switches in cold.
the Off position. Determine and correct the
6. Turn the control box On/Off switch to Off,
cause of the failure. Push in the reset button
and repeat steps 2 through 5 if the engine fails
and repeat the starting procedure.
to start.
NOTE: The Auto Start system, included with
the cab control box option, functions like the CAUTION: Never use starting fluid.
CYCLE-SENTRY system except that once
started the unit does not shut down on
thermostat demand. The unit runs
continuously until it is turned Off manually. Starting the Unit—CYCLE-SENTRY
Units on Diesel Operation
The start sequence, once initiated, is the
same for both systems. Refer to the Selection of Operating Modes on
CYCLE-SENTRY sections of this manual for CYCLE-SENTRY Equipped Units
further information on the start sequence, as
The Thermo King CYCLE-SENTRY system is
it applies to the Auto Start system.
designed to save refrigeration costs. The savings
vary with the commodity, ambient temperatures
and truck insulation. However, not all temperature
controlled products can be properly transported
without continuous air circulation.

38
 Operating Instructions

Since highly sensitive products will normally CYCLE-SENTRY Operation

require continuous air circulation,
With the selector switch placed in the
CYCLE-SENTRY units come equipped with a
CYCLE-SENTRY position, the
selector switch for CYCLE-SENTRY or
CYCLE-SENTRY system shuts down the unit
Continuous Run operation. Your selection of the
when the compartment temperature reaches the
operation mode for the proper protection of a
thermostat setpoint, and restarts the unit on
particular commodity should use the following
thermostat demand.
guidelines.
On CYCLE-SENTRY equipped units, the unit
Examples of Products Normally start-ups may also be initiated by Defrost cycle
Acceptable for CYCLE-SENTRY Operation initiation or engine block temperature switch
demand.
• Frozen foods (in adequately insulated trailers)
If Defrost is initiated either manually, or
• Boxed or processed meats
automatically by the defrost timer, the unit will
• Poultry start and run in Defrost. When the Defrost cycle is
complete, the unit will run in whichever operating
• Fish
mode the thermostat demands until the
• Dairy products compartment temperature reaches setpoint.
• Candy In cold ambients, the CYCLE-SENTRY system
automatically maintains engine temperature by
• Chemicals
restarting the unit if the engine block temperature
• Film drops to 30 F (-1 C). When the unit starts up
because of low engine block temperature, the unit
• All non-edible products.
will run in whichever operating mode the unit
thermostat is calling for until the battery is fully
Examples of Products Normally Requiring
charged and the engine block temperature rises to
Continuous Run Operation of Air Flow
90 F (32 C).
• Fresh fruits and vegetables, especially
After the unit starts from thermostat demand,
asparagus, bananas, broccoli, carrots, citrus,
Defrost initiation, or engine block temperature
green peas, lettuce, peaches, spinach,
switch demand, a Battery Sentry switch monitors
strawberries, sweet corn, etc.
the voltage across the field of the alternator and
• Non-processed meat products (unless will keep the unit running until the battery is
pre-cooled to recommended temperature) recharged sufficiently. The unit runs in whichever
operating mode the thermostat demands to
• Fresh flowers and foliage.
properly maintain the compartment temperature.
The above listings are not all inclusive. Consult When the battery is sufficiently recharged, the
your grower or shipper if you have any questions unit will shut down on thermostat demand.
above the operating mode selection on your type
of load. CAUTION: With the Auto Start/Stop -
Continuous Run switch in the
Continuous Run Operation CYCLE-SENTRY position and the On/Off
With the selector switch in the Cont Run position, switches in the On position, The unit may
the CYCLE-SENTRY unit will operate in its start at any time without prior warning.
regular cooling and heating modes. Refer to NOTE: A buzzer sounds when the unit is
“Manually Starting Units on Diesel Operation” on automatically preheating.
page 38 or “Starting the Unit—CYCLE-SENTRY
Units on Diesel Operation” on page 38.

39
Operating Instructions

NOTE: A unit that is equipped with 7. At the end of the preheat period, the engine
CYCLE-SENTRY should be manually started if will begin cranking. The glow plugs remain
it has been turned Off long enough for the energized during the cranking period. If the
engine to become cold soaked at temperatures engine RPM does not exceed 50 RPM during
below 30 F (-1 C). Place the Auto Start/Stop - the first 4 seconds of cranking, or if the engine
Continuous Run switch in the Cont Run position does not start after 30 seconds of cranking, the
and refer to “Manually Starting Units on Diesel cranking cycle terminates.
Operation” on page 38. After this initial cold
NOTE: If the engine fails to start, the unit
start, the Auto Start/Stop - Continuous Run
reset switch will open, interrupting current to
switch can be switched to the CYCLE-SENTRY
the control system about 40 seconds after
position. CYCLE-SENTRY sensors will then
cranking cycle terminates.
automatically maintain temperatures and
provide reliable unit restarts on demand. 8. If the engine fails to start, place the control
box On/Off switch in the Off position.
Fully charged batteries in good condition are
Determine and correct the cause of the failure,
essential for reliable unit operation. This is
then push in the reset button and repeat the
especially true on CYCLE-SENTRY equipped
starting procedure.
units in cold weather.
1. Place the Diesel/Electric switch in the Diesel Starting the Unit—Electric
position and place the power receptacle Operation
On/Off switch in the On position.
1. Place the Diesel/Electric switch in the Electric
2. Place the CYCLE-SENTRY switch in the position.
CYCLE-SENTRY position.
2. Make sure that an On/Off switch is in the Off
3. Place the control box On/Off switch in the On position and that the electric standby power
position. supply is turned off.
4. Press the ON key in the cab control box. The
CYCLE-SENTRY indicator light will come CAUTION: Always turn Off the electric
On. (This light must be On at all times while power supply when handling, connecting,
the unit is in CYCLE-SENTRY operation.) If or disconnecting high voltage power
a malfunction occurs preventing a restart, the cords.
fact that this light is Off is the only indication 3. Connect the power receptacle to the power
a malfunction has occurred. supply. Make sure that the power supply is the
5. Set each thermostat at the required correct voltage, phase, and frequency.
temperature. Do not set a thermostat lower 4. Turn the high voltage power supply On.
than required (lowering the thermostat
setpoint does not make the unit cool faster). CAUTION: Do not start the electric motor
6. If a thermostat calls for Cool or Heat, the glow unless the diesel engine is completely
plugs will automatically heat for the required stopped.
amount of time depending on the engine
5. Place the On/Off switches in the On position
temperature (5 seconds at 150 F [66 C] to
and press the ON key.
120 seconds at -20 F [-29 C]).
6. Set each thermostat setpoint at the required
temperature. Do not set a thermostat lower
than necessary. Setting the thermostat below
the required setpoint will not make the unit
cool faster.

40
 Operating Instructions

7. If a thermostat is demanding Cool or Heat, the Loading Procedure

electric motor will start and the unit will
operate. The unit will not operate if the box 1. Make sure the unit is Off before opening the
temperature is near the thermostat setpoint. doors to minimize frost accumulation on the
evaporator coil and heat gain in the truck.
8. Check the fan rotation by holding a small (Unit may be running when loading the truck
piece of cloth or paper in front of the from a warehouse with door seals.)
condenser grille. Correct fan rotation will
draw the cloth or paper toward the grille, 2. Spot check and record the load temperature
incorrect rotation will blow the cloth or paper while loading. Especially note any
away. off-temperature product.

9. If the fan rotation is correct, leave the unit 3. Load product so that there is adequate space
turned On. for air circulation completely around the load.
Do not block the evaporator inlet or outlet.
10. If the rotation is incorrect, the phase of the
power supply is wrong and must be corrected. 4. Products should be pre-cooled before loading.
Turn Off the power to the cable and reverse Thermo King units are designed to maintain
the position of any two power leads from the loads at the temperature at which they were
power cable plug. Do not disturb the green loaded. Transport refrigeration units are not
ground wire. (Refer this procedure to a designed to pull hot loads down to
qualified electrical repairman). temperature.

After Start Inspection Post Load Procedure

Compressor Oil: The compressor oil level should 1. Make sure all the doors are closed and locked.
be visible in the sight glass. 2. Set the thermostat at the required temperature
Refrigerant: Checkthe refrigerant charge, see setpoint.
Refrigerant Charge in the Refrigeration
3. Start the unit.
Maintenance chapter.
Thermostat: Set the thermostat at, well above or 4. One-half hour after loading, Defrost each
well below the compartment temperature. Check evaporator by momentarily pressing the
to make sure that the mode of operation changes Manual Defrost keys. If the evaporator coil
with the change in setpoint. temperature has dropped below 42 F (6 C), the
unit will Defrost. The Defrost cycle should
Pre-Cooling: With the thermostat set at the stop automatically.
required temperature, allow the unit to run for
one-half to one hour (longer if possible) before
loading the truck. Pre-cooling will remove Post Trip Checks
residual body heat and moisture from the truck 1. Wash the unit.
interior and provide a good test of the
refrigeration system. 2. Check for leaks.

Defrost: When the unit has finished pre-cooling 3. Check for loose or missing hardware.
the truck interior (evaporator coil temperature 4. Check for physical damage to the unit.
below 42 F [6 C]), initiate Defrost cycle with the
MANUAL DEFROST key. The Defrost cycle should end
automatically.

41
Operating Instructions

42
Electronic Controls

TG-V Thermostat 1
The TG-V is a programmable microprocessor
controller that uses external relays. The TG-V
module is replaced as an assembly, no internal
repair is available.
For complete details, see the Microprocessor
Controller TG-V Operating and Setup Manual TK
40284.
Features of the TG-V Thermostat include:
Thermometer: It displays the return air
temperature, and can be programmed to display
the optional discharge air temperature with 0.1
degree accuracy.
Thermostat: It provides temperature control from
-20 to 80 F (-28 to 28 C), in 0.5 degree
increments.
9072a
Defrost Control: When the evaporator coil is cold
enough for frost to form, defrost is automatically
2
initiated every 4 hours during pull-down until the
return air temperature is in range. At in-range 1. LCD
temperatures (between approximately 7 degrees 2. Keypad
above and 7 degrees between point), the controller
is programmable for 2 to 16 hours in 2 hour Figure 8: TG-V Thermostat
increments. Defrost interval is set at the factory
but can be reprogrammed by your Thermo King The keypad and the Liquid Crystal Display (LCD)
Dealer. It can also be programmed to terminate allow the operator to operate the TG-V. The input
defrost at 30 or 45 minutes. and output terminals on the back of the TG-V
monitor unit conditions and control unit functions.
Fuel Saver: It can be programmed to delay high
speed operation for optimum fuel economy.
Alarm: It can detect and display up to four alarm
conditions including sensor, microprocessor, and
defrost termination failures.

43
Electronic Controls

Single Temp In-Cab TG-V

Controller (optional)
The In-Cab TG-V Controller is a microprocessor
based controller that is designed to be used in
Thermo King Units.
For complete details, see the In-Cab TG-V
Controller Operating and Setup Manual TK
40804-8-MS.

Single Temp In-Cab TG-V Controller

The early versions of the Single Temp In-Cab

TG-V have the following part numbers:
• P/N 41-1544 - 12V No Modulation
• P/N 41-1545 - 12V Modulation
• P/N 41-1546 - 24V No Modulation
• P/N 41-1547 - 24V Modulation.
The software and alarm codes were updated in the
first quarter of 2000. The updated versions of the
Single Temp In-Cab TG-V have the following
part numbers:
• P/N 41-3305 - 12V No Modulation
• P/N 41-3306 - 12V Modulation
• P/N 41-3307 - 24V No Modulation
• P/N 41-3308 - 24V Modulation
• P/N 41-3309 - Isuzu.
The face plate is P/N 91-8117 for all versions,
except for Isuzu.
Interconnecting harness P/N 41-346 is used for all
versions.

44
 Electronic Controls

Display Symbols and Control

Keys
The following is a list of the display symbols and
control keys on the TG-V. It is recommended that
you become completely familiar with the meaning
of each symbol and the function of each control
key before operating the unit.

Display Symbols
Return Air Symbol
(Arrow returning from thermometer to unit.)
Indicates that the return air temperature is being
displayed.

Discharge Air Symbol

(Arrow from unit pointing at thermometer.)
Indicates that the discharge air temperature is
being displayed (optional).

Setpoint Symbol
(Hand pointing to thermometer.) Indicates that the
setpoint temperature is being displayed.

Fahrenheit Symbol
(Degree symbol and letter F.) Indicates that the
temperature being displayed is in Degrees
Fahrenheit.

Minus Sign
Indicates that the temperature being displayed is
below zero.

45
Electronic Controls

Celsius Symbol
(Degree symbol and letter C.) Indicates that the
temperature being displayed is in Degrees
Celsius.

Temperature
When a temperature symbol is displayed:
• Large numbers indicate the temperature in
whole degrees.
• A decimal point and 1/2 size number indicates
temperature in tenths of a degree.

Alarm Symbol
(Exclamation point within a triangle.) When this
flashing symbol is displayed, an alarm (fault)
condition has been detected by the controller.

Alarm Code
When an alarm has been sensed and an alarm
screen has been selected by pressing the SELECT
key, this two-digit code indicates the type of
alarm.

46
 Electronic Controls

Control Keys
SELECT Key
(Cycling arrows) is used to select the various
displays which can appear on the screen.

ENTER Key
(Equals sign) is used to enter new information
into the controller.

UP Key
(Arrow pointing upward) When the setpoint
symbol is on the screen, this key is used to
increase the setpoint temperature.

DOWN Key
(Arrow pointing downward) When the setpoint
symbol is on the screen, this key is used to
decrease the setpoint temperature.

47
Electronic Controls

General Display Information

When the Thermo King unit is switched Off, the
controller screen will be dark; nothing will be on
the display.

When the Thermo King unit is switched On, all

symbols and readouts will be displayed for about
5 seconds. Make sure that all display segments are
operational.

After 5 seconds the Standard Display will appear.

This display remains on the screen during normal
operation. The Standard Display is set to Return
Air Temperature at the factory, however, the
controller can be programmed to show Discharge
Air, Return Air, or Setpoint as the Standard
Display.

48
 Electronic Controls

When the Thermo King unit is switched Off, it is

normal for the display to remain On for about 30
seconds as it slowly fades.
NOTE: With the power Off or battery
disconnected, all settings are saved in the
controller memory and become active when the
unit is switched On.

49
Electronic Controls

Displaying Operating Data

During normal operation, the Standard Display is
on the screen. Return Air Temperature is the
factory Standard Display setting (this may be
changed). Other operating data can also be
displayed.
To view other operating data, repeatedly press and
release the SELECT key.
In addition to Return Air Temperature, the
following data may be displayed:

• Discharge Air Temperature (optional)

Press for next display.

• Setpoint Temperature

Press for next display.

50
 Electronic Controls

• Alarms
(Can be displayed only when an alarm
condition has been sensed by the controller).
When viewing a display...If no keys are pressed,
the Standard Display will automatically reappear
on the screen in about 10 seconds.

51
Electronic Controls

Entering the Setpoint

The setpoint temperature of the Thermo King unit
can be easily and quickly changed. To change the
setpoint:
1. Press and release the SELECT key repeatedly
until the setpoint symbol is on the screen.

2. Press the UP or DOWN key until the setpoint is

at the correct temperature setting.
• Pressing and releasing either key
repeatedly will cause the temperature to
change by .5 degree each key press.
• Holding either key down will cause the
temperature to scroll automatically, one
degree at a time.

3. To enter the new setpoint into memory: Press

and release the ENTER key within 5 seconds.
• The display will blink once as the new
setpoint is entered into memory.
• The new setpoint will remain on the screen
for about 5 seconds, then,
• The standard screen will automatically
appear.

CAUTION: If the ENTER key is not pressed

within 5 seconds: the original setpoint will
appear on the screen for 5 seconds, the
standard screen will automatically appear,
and the Thermo King unit will be
controlled at the original setpoint.

1. Setpoint Symbol
2. Setpoint Temperature
3. New Setpoint Temperature

52
 Electronic Controls

Displaying and Clearing Alarm

Codes
When the TG-V controller senses an alarm
condition, a flashing alarm symbol appears on the
display. A two digit alarm code is used to identify
the type of alarm.
1. To display the alarm code, repeatedly press
and release the SELECT key until the alarm
screen is displayed.
• If more than one alarm has been sensed,
all alarm codes present will automatically
alternate on the screen.
• The following alarm codes are used:
03 Return Air Sensor Failure
The Return Air Sensor has failed or is
disconnected.
03A Return Air Sensor Failure
The Return Air Sensor has failed or is
disconnected (Zone 2).
04 Discharge Air Sensor Failure
(Optional)
The Discharge Air Sensor has failed or is
disconnected.
14 Defrost Circuit Failure
The unit is still in defrost after the end of
the defrost time limit, indicating a defrost
circuit failure.
25 Battery Charging Alternator Failure
Current output from the unit alternator is
NOT being sensed.
29 Defrost Initiation Failure
This code indicates that the unit attempted
to enter defrost three times in rapid
succession indicating a shorted air switch,
shorted manual defrost switch or other
defrost circuit failure.

53
Electronic Controls

47Zone 2 Evaporator Defrost Circuit

Failure
Zone 2 evaporator is still in defrost after
end of the defrost time limit, indicating a
defrost circuit failure (No. Rh circuit).
74 Cold Start or Checksum Error
Test In-Cab TG-V with tester P/N 204-83.
75 Microprocessor RAM Faulty
Test In-Cab TG-V with tester P/N 204-83.
76 Microprocessor EEPROM Faulty
Test In-Cab TG-V with tester P/N 204-83.
77 EPROM Faulty
Test In-Cab TG-V with tester P/N 204-83.
87 Field Test Error
88 Microprocessor Failure
The TG-V has failed and must be
replaced.
2. To clear the alarms, press the ENTER key while
the alarm screen is showing. The alarms will
clear and the Standard Display will appear on
the screen.
• Alarms may continue to appear as the unit
operates if the alarm condition is not
corrected.

54
 Electronic Controls

Additional Operating
Information
Sensor Failure
In addition to generating an alarm, the failure of a
sensor will cause the display screen for that sensor
to show a minus sign and dashes in place of
temperature. The alarm symbol, the minus sign
and the dashes will blink continuously.

Temperatures Outside of Display

Range
The Microprocessor Controller TG-V is capable
of displaying temperatures ranging from -40 to
99.9 F (-40 to 37.8 C). A blinking temperature
display of -40 or 99.9 F (-40 or 37.8 C) without an
alarm symbol, indicates the unit is functioning
normally but the temperature being sensed is
outside of the display range of the controller.
Example: If the temperature in the cargo
compartment were 110 F, the display would read
99.9 F (-37.8 C) and would blink continuously.
The display would stop blinking once the
temperature dropped below 99.9 F (-37.8 C).

55
Electronic Controls

Guarded Access Mode If the controller is being replaced, the

programming set-up codes must be set to match
The TG-V controller is pre programmed at the the configuration of the unit.
factory to match the standard configuration and
operating requirements of the unit. The factory programming set-up codes can be
found on the schematic and wiring diagrams for
the unit. Special changes in the programming can
be made for specific special applications.

Programming
Programming is done through the Guarded Access
mode.
The Guarded Access mode consists of 5 screens
numbered 1 through 5. Screen numbers are
indicated by a 1/2 size digit.
The Microprocessor Controller is programmed by
entering a two digit set-up code into each screen.
Thermostat Set-Up Codes Set-up code 68 is the standard set-up code for
Screen 1 on CD-II MAX (NAD) units.
Left Digit Right Digit Screen
USA EEC Programming the controller requires the
following:
6 8 9 1
1 1 1 2 • Choosing the desired set-up code for each
screen.
0 0 0 3
0 0 0 4
• Entering the Guarded Access mode.
0 1 1 5 • Changing the set-up codes as required.

Choosing Set-up Codes

The standard set-up codes for the CD-II MAX are
shown at the left.
NOTE: The set-up code for Screen 3 can be
determined by checking the sensors themselves.
Each two digit set-up code can represent several
operational settings of the Thermo King unit.
The factory programming set-up codes can be
found on the schematic and wiring diagrams for
the unit.
If the set-up codes are not available, they can be
determined using information shown later in this
chapter.

56
 Electronic Controls

Before entering the Guarded Access mode or

changing set-up codes:
1. Choose the set-up codes for each screen.
2. Write the set-up codes in the space provided
or on a separate piece of paper.

57
Electronic Controls

Entering the Guarded Access Mode

To get to the Guarded Access mode:
1. Press and release the SELECT key repeatedly
until the setpoint symbol is on the screen.
NOTE: Record the setpoint so that the unit
may be returned to the original setting when
programing is finished.

1. Setpoint Symbol

2. Press the UP or DOWN key until the setpoint is

at exactly 32.0 F or 0.0 C.
3. Press and release the ENTER key within 5
seconds to enter the setpoint into the
controller.

58
 Electronic Controls

4. Press the SELECT key until the setpoint symbol

is again on the screen. However, this time,
when the setpoint symbol comes on the
screen, Do Not release the SELECT key, hold it
down.

5. While holding down the SELECT key, press the

UP key and the DOWN key at the same time.

• Screen 1 in the Guarded Access mode will

appear.

To select other Guarded Access screens, press

and release the SELECT key until the desired
screen is on the display.
If no keys are pressed, the Standard Display
will automatically reappear on the screen in
about 10 seconds.

1. Current Setup Code

2. Screen Number

59
Electronic Controls

Changing Set-Up Codes

To change the set-up code:

1. With a Guarded Access screen on the display,

press the UP key or the DOWN key repeatedly
until the desired code is on the screen.
NOTE: Display digits cannot be set
individually. The UP or DOWN key is used to
“scroll” the display until the correct two digit
code is on the screen.
2. To enter the new set-up code into memory:
Press and release the ENTER key within 5
seconds.
• The display will blink once as the new
1. New Set-up Code code is entered into memory.
• The new code will remain on the screen
for about 5 seconds and then,
• The standard screen will automatically
appear.
or
• You may go to another Guarded Access
screen by pressing and releasing the
SELECT key within 5 seconds of entering
the new code. To change the set-up code
on other screens, repeat steps 1 and 2.

CAUTION: If the ENTER key is not pressed

within 5 seconds: the original set-up code
will appear on the screen for 5 seconds,
the standard screen will automatically
appear, and the controller will operate
with the original set-up code for that
screen.
NOTE: Remember to return the controller to the
original setpoint when programming is finished.

60
 Electronic Controls

Screen 1 The Microprocessor Controller should be set

to save elapsed time:
The set-up code for Screen 1 represents a
combination of the following seven settings: • In delivery applications where the unit will
be turned On and Off before a normal
1. Save Elapsed Time
defrost time has elapsed.
Elapsed time is the duration between the end
• In units without an air switch.
of one Defrost cycle and the beginning of the
next. Elapsed time should not be saved in normal,
over-the-road applications where the unit is
The TG-V Microprocessor Controller has a
run continuously and is not frequently turned
built in defrost interval timer which can
Off and On.
automatically initiate a Defrost cycle after a
preset period of time has elapsed. Settings:
When the Thermo King unit is switched Off, YES = Save elapsed time.
the defrost interval timer can be set to do one
NO = Do not save elapsed time.
of two things:
2. Defrost Terminate Time
• It can save the time which has elapsed
since the last defrost and continue on when If a Defrost cycle is not terminated
the unit is restarted. automatically, the TG-V Microprocessor
Controller terminates the Defrost cycle after
• Or, it can reset and start timing again from
the programmed period of time.
the beginning.
Settings:
Example: Defrost interval time is set to 2
hours. The unit is switched Off after 1 hour 30 minutes or 45 minutes.
(that is, a defrost interval of 1 hour has
3. High Speed Delay
elapsed):
To save fuel when the cargo compartment
• If the elapsed time has been saved; when
temperature is in range, the TG-V
the unit is turned back On, the timer could
Microprocessor Controller can delay high
initiate defrost 1 hour later. The total
speed heat or high speed cool for 8 minutes.
interval is 1 hour of elapsed time plus 1 Settings:
hour of time since the unit was turned On.
YES = Delay high speed operation for 8
• If the elapsed time has not been saved;
minutes.
when the unit is turned back On, the timer
will reset and start timing again from the NO = Do not delay high speed operation
beginning. The timer could initiate defrost for 8 minutes.
2 hours from the time the unit was turned
NOTE: In order for the High Speed Delay to
back On.
operate, the 7K terminal must be used.
NOTE: Low Speed heat is only available in
Continuous Run operation. In
CYCLE-SENTRY, the unit restarts and runs
in High Speed Heat.

61
Electronic Controls

4. High Speed Heat Lockout 7. Modulation Valve

To protect frozen foods, the TG-V can lockout The TG-V can control Thermo King units
high speed heat when the setpoint is below which are equipped with a modulation valve.
15 F (-9.4 C).
Settings:
Settings:
YES = Unit has a modulation valve.
YES = Lockout high speed heat below
NO = Unit does not have a modulation
15 F (-9.4 C).
valve.
NO = Do not lockout high speed heat
NOTE: Units with a modulation valve must
below 15 F (-9.4 C).
have a discharge air sensor connected to the
5. Fahrenheit/Celsius controller.
The TG-V can display temperatures in either If the sensor is not connected, the controller
Fahrenheit or Celsius. will display an alarm symbol and the alarm
display will show Alarm Code 04 (Discharge
Settings:
Air Sensor Faulty).
F = Fahrenheit
C = Celsius
Directions for choosing the set-up codes for
Screen 1 are on the next page.
6. Discharge Sensor
When an optional discharge air sensor is
connected to the TG-V, the discharge air
temperature can be displayed.
Settings:
YES = Discharge sensor connected,
display discharge air temperature.
NO = Discharge sensor not connected, do
not display discharge air temperature.
NOTE: If the unit does not have a discharge
air sensor, but the discharge sensor setting is
set to “YES”, the controller will display an
alarm symbol and the alarm screen will show
Alarm Code 04 (Discharge Air Sensor
Faulty). Instead of showing a temperature,
the discharge air screen will display dashes.

62
 Electronic Controls

Set-up Code—Screen #1
Save Defrost High Code
Elapsed Terminate Speed
Time Time Delay
No 30 min No 0
No 30 min Yes 1
No 45 min No 2
No 45 min Yes 3
Yes 30 min No 4
Yes 30 min Yes 5
Yes 45 min No 6
Yes 45 min Yes 7

Directions: To determine the two digit set-up

code for Screen #1:
1. Select the code number that matches the
correct combination of settings from the top
table. This becomes the left digit.
2. Select the code number that matches the
correct combination of settings from the
bottom table. This becomes the right digit.
NOTE: Factory standard settings are in bold
type.
High Discharge Modulation Fahrenheit Code
Speed Sensor Valve /Celsius
Heat
Lockout
No No No F 0
No No No C 1
No No Yes F 2
No No Yes C 3
No Yes No F 4
No Yes No C 5
No Yes Yes F 6
No Yes Yes C 7
Yes No No F 8
Yes No No C 9
Yes No Yes F A
Yes No Yes C B
Yes Yes No F C
Yes Yes No C D
Yes Yes Yes F E
Yes Yes Yes C F

63
Electronic Controls

Screen #2
Defrost intervals are set with Screen #2. A defrost
interval is the period of time between the end of
one Defrost cycle and the beginning of the next.
During pull-down the defrost interval is 4 hours.
Once the unit is in-range, the defrost interval
becomes the interval set with this screen.

Defrost Time Interval Above Lockout

Sets the defrost interval for setpoint temperatures
above 15 F (-9.4 C).
Settings:
2, 4, 6, 8, 10, 12, 14 or 16 hours.

Defrost Time Interval Below Lockout

Sets the defrost interval for setpoint temperatures
below 15 F (-9.4 C).
Settings:
2, 4, 6, 8, 10, 12, 14 or 16 hours.
Directions for choosing the set-up codes for
Screen #2 are on the next page.
NOTE: The 1 hour defrost interval is provided
for checking the system and is not intended as a
practical defrost interval.

64
 Electronic Controls

Set-Up Code—Screen #2

Defrost Code
Time Above
Lockout
2 Hours 0
4 Hours 1
Left Digit
6 Hours 2
8 Hours 3
10 Hours 4
12 Hours 5
14 Hours 6
16 Hours 7
1 Hour 8

Directions: To determine the two digit set-up

code for Screen #2.
1. Select the code number that matches the
correct setting from the top table. This
becomes the left digit.
2. Select the code number that matches the
correct setting from the bottom table. This
becomes the right digit.
NOTE: Factory standard settings are listed in
the wiring and schematic diagrams for each
unit.

Defrost Code
Time Below
Lockout
2 Hours 0
4 Hours 1
6 Hours 2
8 Hours 3
10 Hours 4
12 Hours 5
14 Hours 6
16 Hours 7
1 Hour 8

65
Electronic Controls

Screen #3 Discharge Sensor Grade (Optional)

For accuracy, the Microprocessor Controller must Matches controller operation to the grade of the
be adjusted to match the unit sensors. That discharge air sensor.
adjustment is done with Screen #3.
Settings:
There are two types of sensors, graded and
Grades 0, 1, 2, 3, 4, or 5.
ungraded.
Graded sensors are measured and presorted at the Return Sensor Grade
factory into categories (grades) based on their
Matches controller operation to the grade of the
electrical resistance. They are marked with grades
return air sensor.
1 through 5. Graded sensors, regardless of grade
number, are accurate to within ±.125 degrees. Settings:
Ungraded sensors are not sorted and therefore Grades 0, 1, 2, 3, 4, or 5.
have a wider possible range of resistance. They do
NOTE: An ungraded sensor can be partially
not have grading marks and are accurate to ±.6
graded by immersing the sensor in a good ice
degrees.
bath and then selecting various sensor grades
The TG-V Microprocessor Controller can be until the return air (or discharge air)
calibrated to work with either type of sensor. temperature reads 32.0 F (or 0.0 C). The sensor
may then be accurate for freezing temperature
For graded sensors, set the controller to match the
but may not be accurate towards either extreme
grade of the sensor. Example: for a grade 4 sensor,
of the controller range.
the controller setting would be 4.
NOTE: When return air and discharge air
For ungraded sensors, set the controller to grade 0.
sensors are used with a modulation control
Directions for choosing the set-up codes for valve, graded sensors must be used. Without
Screen #3 are on the next page. modulation, the use of graded sensors is
optional.
NOTE: The return air sensor is the primary
control sensor and must be connected at all
times.

66
 Electronic Controls

Set-Up Code—Screen #3

Discharge Code
Sensor
Grade
0 0
1 1 Left Digit
2 2
3 3
4 4
5 5

Directions: To determine the two digit set-up

code for Screen #3.
1. Select the code number that matches the
discharge air sensor grade from the top table.
This becomes the left digit.
2. Select the code number that matches the return
air sensor grade from the bottom table. This
becomes the right digit.
NOTE: Factory standard settings are listed in
the wiring and schematic diagrams for each
unit.

Return Code
Sensor
Grade
0 0
1 1
2 2
3 3
4 4
5 5

67
Electronic Controls

Screen #4
The “Standard Display” is set with Screen #4.

Standard Display
The Standard Display normally appears on the
screen. The screen automatically returns to the
Standard Display when viewing of other screens
is complete and no keys are pressed for about 10
seconds.
Settings:
• Return Air Temperature
• Setpoint Temperature
• Discharge Air Temperature (optional).
NOTE: This screen is available only when the NOTE: The Left Digit is always zero.
Discharge Sensor setting (Screen #1) is set to
YES.
• Alternate between Return Air Temperature
and Setpoint Temperature (Return Air 30
seconds, Setpoint 5 seconds).
• Alternate between Discharge Air Temperature
and Setpoint Temperature (Discharge Air 30
seconds, Setpoint 5 seconds). This screen is
available only when the Discharge Sensor
setting (Screen #1) is set to YES, and the
discharge sensor is installed.
NOTE: This screen is available only when the
Discharge Sensor setting (Screen #1) is set to
YES.

68
 Electronic Controls

Directions: To determine the two digit set-up

code for Screen #4.
• Select the code number that matches the
correct Standard Display. The LEFT digit of
the code number becomes the LEFT digit on
the screen. The RIGHT digit of the code
number becomes the RIGHT digit on the
screen.
NOTE: Factory standard settings are listed in
the wiring and schematic diagrams for each
unit.

Defrost Model Display

The purpose of this modification is to allow the
default display to include a periodic indication
that the system is in the Defrost mode.
The new selections possible on Guarded Access
Screen 4 are as follows:

Screen 4 Selection
Default Display Left Digit Right Digit
Code Code
Return Air Temperature 0 0
Setpoint Temperature 00 1
Discharge Air 00 2
Temperature
Alternate Return Air 00 3
Temperature and
Setpoint Temperature
Alternate Discharge Air 00 4
Temperature and
Setpoint Temperature

69
Electronic Controls

Screen #5 As operation continues:

The set-up code for Screen #5 represents a • In Continuous Run or CYCLE-SENTRY, if
combination of the following settings: setpoint has not been reached in eight minutes
while running low speed cool, the unit will
High Speed (Cool) Pull-Down switch to high speed cool, driving the return
air temperature back down to setpoint.
This feature provides faster temperature
Pull-Down for critical cargos. • If the unit has been running in low speed cool
for less than eight minutes and the return air
At start-up:
temperature reaches setpoint:
• In Continuous Run or CYCLE-SENTRY, to
• Units operating in Continuous Run will
reduce the time needed to bring cargo box
switch to low speed heat changing to low
temperature down to setpoint (Pull-Down),
speed cool as necessary.
the unit will operate in High Speed Cool until
the return air temperature reaches setpoint. • Units operating in CYCLE-SENTRY will
shut down, restarting as necessary.
• Once the return air temperature reaches
setpoint: • In Continuous Run or CYCLE-SENTRY, if
the return air temperature reaches 5.1 F
• Units operating in Continuous Run will
(2.8 C) degrees above setpoint, the unit will
switch to low speed cool for five seconds
immediately switch to high speed cool, unless
then to low speed heat. The unit will then
the Fuel Saver 8 minute Delay to High Speed
cycle between Low Speed Heat and Low
is active.
Speed Cool as necessary.
NOTE: High Speed Pull-Down will be inactive
• Units operating in CYCLE-SENTRY will
in units with modulation that are operating in
switch to low speed cool for five seconds
Continuous Run above 15 F (-9C).
to allow Battery Sentry to check the
charging current. If the battery is charged,
High Speed Pull-Down Fresh
the unit is not in defrost and the engine
block is sufficiently warm, the unit will The controller can initiate a High Speed
shut-down, restarting as necessary. If not, Pull-Down to setpoint of fresh loads above 15 F
the unit will continue to run switching (-9.4 C).
from low speed heat to low speed cool as
Settings:
necessary.
YES = Enable High Speed Pull-Down to
setpoint.
NO = Normal operation. Do not enable high
speed pull-down to setpoint.

70
 Electronic Controls

High Speed Pull-Down Frozen

The controller can initiate a High Speed
Pull-Down to setpoint of frozen loads at or below
15 F (-9.4 C).
Settings:
YES = Enable High Speed Pull-Down to
setpoint.
NO = Normal operation. Do not enable High
Speed Pull-Down to setpoint.

2 Minute Low Speed Start (Continuous

Run only)
This setting allows the engine to warm-up by
running it in low speed for 2 minutes when the
unit is first started. After 2 minutes, the unit will
resume normal operation.
This setting functions only while the unit is
operating in Continuous Run.
Settings:
YES = Enable 2 minute low speed start.
NO = Normal operation. Do not enable 2
minute low speed start.

Reduced Setpoint Range

Smaller truck units are not designed to operate
with a setpoint range of -20 to 80 F (-28 to 28 C).
For these units the setpoint range must be reduced
to 0 to 80 F (-18 to 28 C).
This setting is programmed at the factory. Change
it only when replacing the controller, and then
only to the original factory setting for your unit.
Settings:
YES = Reduce setpoint range to 0 to 80 F (-18
to 28 C).
NO = Do not reduce setpoint range.

71
Electronic Controls

Set-Up Code—Screen #5*

Code
0
Left Digit

Directions: To determine the two digit set-up

code for Screen #5:
1. Left digit code number is always 0 for this
screen.
2. Select the code number that matches the
correct combination of settings from the
bottom table. This becomes the right digit.
NOTE: Factory standard settings are listed in
the appropriate wiring and schematic diagrams
for each unit.

High High 2 Minute Reduced Code

Speed Speed Low Setpoint
Pull Pull Speed Range
Down Down Start*
Fresh Frozen
No No No F 0
No No No Yes 1
No No Yes No 2
No No Yes Yes 3
No Yes No No 4
No Yes No Yes 5
No Yes Yes No 6
No Yes Yes Yes 7
Yes No No No 8
Yes No No Yes 9
Yes No Yes No A
Yes No Yes Yes b
Yes Yes No No C
Yes Yes No Yes d
Yes Yes Yes No E
Yes Yes Yes Yes F
* Functions in Continuous Run only

72
 Electronic Controls

In-Range Temperature Differential Setting

The In-Range Temperature Differential Setting is
set with Screen 5. This setting determines the
range used in monitering in-range and out of
range conditions.
The following settings are available for
Fahrenheit or Celcius readouts:
• Fahrenheit: 0.0 F (OFF), 6, 10, 14, and 18
degrees
• Celsius: 0.0 F (OFF), 3, 6, and 10 degrees

Figure 9: In-Range Temperature Differential Setting

Directions:
To determine the setting for Screen 5, choose the
temperature differential desired for the in-range
temperature interval.
Example:
To set an in-range temperature differential of 6
degrees above and below the setpoint, select the
number 6.
NOTE: The settings available automatically
correspond to the scale (F or C) chosen in
Display 1.

73
Electronic Controls

Testing the TG-V Thermostat Sensor Test

1. Visually check the bulb end, lead, and
Tools and Materials Required for Testing terminal end of the sensor. Make sure that it is
1. Volt/ohm meter capable of accurately reading not damaged.
1/100 volt increments. 2. Using an ohmmeter capable of reading at least
2. Jumper Wires 4000 ohms, check resistance between the
sensor leads.
3. Three Relays, Part No. 44-5847
3. Sensor resistance should be approximately
4. One 12 Vdc Power Supply 3000 to 3500 ohms. Use the following method
5. Mercury Thermometer to give the sensor a more accurate test:
a. Cool the sensor down to 32 F (0 C) and
TG-V Calibration check the resistance—reading should be
The TG-V thermostat is permanently calibrated, 3266 ± 3.4 ohms.
and no attempt should be made to recalibrate it. b. Warm the sensor up to 70 F (21.1 C) and
The thermostat module is a non-serviceable item check the resistance—reading should be
and repairs should not be attempted. If the 3450 ± 6.9 ohms.
thermostat is found to be defective, replace it.
4. If the sensor does not meet specifications,
Ice-Water Bath Preparation replace it.
1. Fill an insulated container full of ice. Add 5. If the sensor does meet specifications, proceed
enough water to cover the top of the ice during to TG-V thermostat bench test.
the test procedure.
2. Remove the sensor bulb from the unit or use a
known good sensor for testing the thermostat
module.
3. Stir the ice-water bath for one minute or until
stabilized at 32 F (0 C).
4. Monitor the ice-water bath temperature with a
mercury thermometer during testing to ensure
test accuracy.
NOTE: Before testing a questionable thermostat
module, it is a good idea to check the thermostat
sensor first.

74
 Electronic Controls

Preparing TG-V Module for Bench

Test
1. Place the unit On/Off switch in the On
position. (If the thermostat module is out of
the unit, this can be accomplished by
connecting a 12 Vdc power source to the 8
and CH terminals, 8 is connected to positive
(+) and CH is connected to negative (-).
2. Press and release the SELECT key repeatedly
until the setpoint symbol is on the screen.

3. Press the UP and DOWN key until the setpoint is

at exactly 32 F or 0 C.
4. Press the ENTER key (within 5 seconds) to enter
this setpoint.

5. With the setpoint temperature at 32 F or 0 C,

press the UP key, the DOWN key and the SELECT
key at the same time.
• Screen #1 in the Guarded Access
Programming mode will appear.
NOTE: Pressing the three keys at the same
time can be difficult. If it does not work the
first time, return to the setpoint screen with
the setting at 32 F or 0 C and try again. It
may take several attempts.

75
Electronic Controls

6. Press the UP or DOWN key until the set-up code

on Screen #1 reads 68.

7. Press the ENTER key.

If no keys are pressed, the Standard Display will
automatically reappear on the screen in about 10
seconds.

76
 Electronic Controls

TG-V Module Bench Test 9. Set the thermostat module setpoint to 29 F

(-1.7 C). The thermostat is now in low speed
1. Place the main On/Off switch in the Off
cool.
position.
a. Check for voltage between terminal 10T
2. Disconnect all of the wires from the
and CH. Zero volts should be present. The
thermostat module.
speed relay should be de-energized.
3. Connect a known good sensor (yellow
b. Check for voltage between terminals 14T
jacketed) to the terminals labelled SN on the
and CH. Zero volts should be present. The
rear of the thermostat module.
heat relay should be de-energized.
4. To obtain accurate voltage readings during the
10. Set thermostat module setpoint to 33 F
thermostat module checkout, circuits 10T and
(0.6 C). The thermostat is now in low speed
14T must be tested under normal load. This is
heat.
provided by connecting two Bosch relays
(Part No. 44-5847) as follows: a. Check for voltage between terminals 10T
and CH. Zero volts should be present. The
Connect pin 86 of two relays to the negative
speed relay should be de-energized.
(-) terminal of a 12 Vdc power source.
Connect pin 85 of one relay to the 10T b. Check for voltage between terminals 14T
terminal to simulate the speed relay. Connect and CH. 12 volts should be present. The
pin 85 of the second relay to the 14T terminal heat relay should be energized.
to simulate the heat relay.
11. Set the thermostat module setpoint to 36 F
5. Place the sensor bulb in a 32 F (0 C) ice bath. (2.2 C). The thermostat is now in high speed
heat.
6. Connect the positive (+) 12 Vdc power source
on the 8 terminal. Connect the negative (-) a. Check for voltage between terminals 10T
power source to the CH terminal. and CH. 12 volts should be present. The
speed relay should be energized.
7. Check for voltage between 8 and CH. Make
sure approximately 12 volts is present. b. Check for voltage between terminals 14T
and CH. 12 volts should be present. The
NOTE: Due to the accuracy of the TG-V
heat relay should be energized.
module, the digital readout may read a few
tenths of a degree higher than 32 F (0 C). 12. Turn Off the power to the thermostat module.
8. Set the thermostat module setpoint to 24 F 13. Place a jumper wire from the 8 terminal on
(4.4 C). The thermostat is now in high speed thermostat module to the 7K terminal on the
cool. thermostat module.
a. Check for voltage between terminals 10T 14. Turn On the power to the thermostat module.
and CH. 12 volts should be present. The
15. Set thermostat module setpoint to 33 F
speed relay should be energized.
(0.6 C). The thermostat module should now be
b. Check for voltage between terminals 14T in low speed heat. (12 volts present on
and CH. Zero volts should be present. The terminal 14T, zero volts present on terminal
heat relay should be de-energized. 10T). Leaving the jumper from the 8 terminal
to the 7K terminal in place, set the thermostat
module setpoint to 36 F (2.2 C).

77
Electronic Controls

16. Check voltage on 14T and 10T terminals.

a. Check for voltage on terminal 14T. 12
volts should be present. The heat relay
should be energized.
b. Check for voltage on terminal 10T. Zero
volts should be present. The speed relay
should be de-energized. The thermostat
module is in the eight minute High Speed
Lockout mode of operation.
17. At the end of eight minutes, the thermostat
module should automatically switch to high
speed heat. Check the voltage at terminal 10T
after the eight minute interval. 12 volts should
be present.
18. Connect pin 86 of the third relay to the 11
terminal in order to simulate the defrost relay.
Connect pin 85 of this relay to the positive (+)
terminal of the power source.
19. Place a jumper between the 12 terminal and
the negative (-) terminal of the power supply.
Place another jumper between the 12 terminal
and the 11 terminal. The relay should
energize.
20. Remove the jumper between the 12 terminal
and the 11 terminal. The relay should remain
energized.
21. Remove the jumper between the 12 terminal
and the negative (-) terminal of the power
supply. The relay should de-energize.

78
 Electronic Controls

TG-V Terminal Voltage Chart

Voltages must be checked with the yellow
jacketed sensor hooked across the SN terminals
and the bulb placed in a 32 F (0 C) ice-water bath.
HSC LSC LSH HSH
Setpoint Setpoint Setpoint Setpoint
24 F 29 F 33 F 36 F
8 12 Vdc 12 Vdc 12 Vdc 12 Vdc
CH 0 Vdc 0 Vdc 0 Vdc 0 Vdc
29 0 Vdc 0 Vdc 0 Vdc 0 Vdc
10T 12 Vdc 0 Vdc 0 Vdc 12 Vdc See note below.
14T 0 Vdc 0 Vdc 12 Vdc 12 Vdc
Return Air SN — — — —
Sensor
SN — — — —
HFL 0 Vdc 0 Vdc 0 Vdc 0 Vdc
HLO 0 Vdc 0 Vdc 0 Vdc 0 Vdc
38 0 Vdc 12 Vdc 12 Vdc 0 Vdc
7T 0 Vdc 0 Vdc 0 Vdc 0 Vdc
SP 1.95 Vdc 2.00 Vdc 2.04 Vdc 2.07 Vdc
12 12 Vdc 12 Vdc 12 Vdc 12 Vdc
11 12 Vdc 12 Vdc 12 Vdc 12 Vdc
HGV 0 Vdc 0 Vdc 0 Vdc 0 Vdc
7K 0 Vdc 0 Vdc 0 Vdc 0 Vdc
MOD (-) 0 Vdc* 0 Vdc* 0 Vdc* 0 Vdc*
(+) 0 Vdc* 0 Vdc* 0 Vdc* 0 Vdc*
Disc 8B 0 Vdc 0 Vdc 0 Vdc 0 Vdc
Sensor — — — —
Sensor — — — —

HSC - High Speed Cool

LSC - Low Speed Cool
LSH - Low Speed Heat
HSH - High Speed Heat

79
Electronic Controls

TG-V Terminal Identification

2 3 4 5 6 7 8

aea957

1. Basic Terminal Functions

2. (8) Supply Voltage From Unit To Thermostat Module
3. (Ch) Thermostat Module Ground Circuit
4. (29) Force To High Speed (Input) During Defrost
5. (10t) Applies Voltage To Speed Relay Coil When Calling For High Speed
6. (14t) Applies Voltage To Heat Relay Coil When Calling For Heat
7. (Sn) Connects One Lead Of The Return Air Sensor To Thermostat
8. (Sn) Connects Other Lead Of The Return Air Sensor To Thermostat

80
 Electronic Controls

TG-V Terminal Identification

2 3 4 5 6 7 8

aea958

1. Specialized Terminal Functions

2. (Hfl) Force Heat Lockout
3. (Hlo) Heat Lockout Output
4. (38) In-range Output
5. (7t) Force High Speed Cool
6. (Sp) Setpoint Output
7. (12) Defrost Circuit
8. (11) Defrost Circuit

81
Electronic Controls

TG-V Terminal Identification

2 3 4 5 6 7 8

aea959

1. Specialized Terminal Functions

2. (Hgv) Hot Gas Bypass Valve
3. (7k) Accumulative Defrost Time And High Speed Delay Input
4. (-) Output To Modulation Valve Not Connected To Ch Ground
5. (+) Output To Modulation Valve
6. (8b) CYCLE-SENTRY Is In Operation (Input)
7. (Disc Sensor) Connects One Lead Of Discharge Air Sensor To Thermostat
8. (Disc Sensor) Connects Other Lead Of Discharge Air Sensor To Thermostat

82
 Electronic Controls

Sensor Test a. Cool the sensor down to 32.0 F (0.0 C)

and check the resistance. The reading
1. Visually check the bulb end, lead, and
should be 3266 ± 3.4 ohms.
terminal end of the sensor. Make sure that it is
not damaged. b. Warm the sensor up to 70.0 F (21.1 C) and
check the resistance. The reading should
2. Using an ohmmeter capable of reading at least
be 3450 ± 6.9 ohms.
4000 ohms, check the resistance between the
sensor lead terminals. 4. If the sensor does not meet specifications,
replace it.
3. Sensor resistance should be approximately
3000 to 3500 ohms. Use the following method
to give the sensor a more accurate test:

AEA617

1. Band Wraps—if Used, The Return Air Sensor Has Yellow Band
Wraps And The Discharge Air Sensor Has Red Band Wraps.
2. Sensor Lead Terminals

Figure 10: Sensor

83
Electronic Controls

84
Electrical Maintenance

Alternator (Prestolite) • When testing alternators use accurate

equipment such as a Thermo King P/N
NOTE: Units manufactured with 204-615 (FLUKE 23) digital multimeter and a
CYCLE-SENTRY and alternators with integral Thermo King P/N 204-613 amp clamp or an
regulators MUST use replacement alternators equivalent.
with integral regulators.
• Make sure the drive belts and pulleys of the
CAUTION: Full-fielding alternators charging system are in good condition and are
with the integral regulator is adjusted properly before testing the alternator.
accomplished by installing a jumper from Worn belts and pulleys or loose belts will
terminal F2 to ground. Attempting to lower the output of the alternator.
full-field the alternator by applying battery • The battery must be well charged, the battery
voltage to terminal F2 will cause voltage cable connections must be clean and tight, and
regulator failure. the 2A and excitation circuits must be
Complete the following checkout procedure connected properly.
before replacing the voltage regulator or the
alternator.

3
1

6 AJA1520

1. EXC Terminal 5. NEG—B- Terminal

2. F2 Terminal 6. POS—B+ Terminal
3. VOLT SENSE Terminal 7. REG—D+ Terminal
4. AC TAP Terminal

Figure 11: Prestolite Terminal Locations

85
Electrical Maintenance

NOTE: All voltage readings should be taken b. If there is low or no output, the alternator
between the negative battery terminal, or a good is probably faulty. However, the following
chassis ground, and the terminals indicated, items are potential causes for not charging:
unless stated otherwise.
• Check the alternator brushes
1. Set the unit for Continuous Run operation and
• Check the 2A circuit from the
place the On/Off switch in the Off position.
alternator to the battery
2. Check the battery voltage. If the battery
• Properly tension the alternator belt
voltage is less than 12 volts, the battery must
be charged or tested to determine if it should • Check battery cable connections and
be replaced. the alternator ground. They must be
clean and tight
3. Check the voltage at the B+ terminal on the
alternator. Battery voltage must be present. If • The battery must be in good condition
not, check the 2A circuit. and must accept a charge
4. Check the voltage at the VOLT SENSE • Check for excessive or unusual
terminal on the alternator. Battery voltage amperage draw by the unit control
must be present. If not, check the 2 circuit. circuits.
5. Set the unit for continuous run operation and
place the main On/Off switch in the On Excessive Voltage Output
position. 12 Volt Alternators With Internal Regulator
Setting: When a Thermo King unit is installed on
6. Wait 20 seconds for the unloading timer to
a truck, it is often connected to a truck battery.
de-energize the unloading relay and check the
When both the Thermo King unit and the truck
voltage at the EXC terminal on the alternator.
engine are running on the truck battery, the
Battery voltage must be present. If not, check
charging system with the higher voltage may
the EXC circuit.
automatically turn Off the charging system with
7. Attach a clamp-on ammeter to the 2A wire the lower voltage output.
connected to the B+ terminal on the alternator.
If it is determined that the Thermo King regulator
8. Connect a voltmeter between the B+ terminal setting is higher than the truck charging system or
and a chassis ground. the batteries are consuming more water than
normal the following solution may help solve the
9. Start the unit and run it in high speed.
problem.
10. Connect a jumper wire between the F2
• Remove the wire labeled SENSE and tape off.
terminal and a chassis ground. This will full
field the alternator. • Add a jumper wire from 2A to the SENSE
terminal on the back of the alternator.
CAUTION: Never apply battery voltage to This should reduce the voltage to the battery by
terminal F2 or voltage regulator failure 0.2 to 0.3 of a volt.
will occur.
a. Full alternator output (the alternators rated
output) indicates the alternator is good but
the voltage regulator needs replacement.

86
 Electrical Maintenance

Battery Preheat Buzzer

NOTE: The Microprocessor Power switch must The preheat buzzer module on the circuit board is
be placed in the Off position before connecting designed to indicate preheat is in operation.
or disconnecting the battery terminals. The
Microprocessor Power switch is located on the RPM Sensor
control box side of the unit.
The RPM sensor is in the engine bell housing
Inspect/clean the battery terminals and check the adjacent to, but not touching, the flywheel
electrolyte level during scheduled maintenance (backed off 1/2 turn).
inspections. A dead or low battery can be the
cause of an ammeter indicating discharge due to The RPM sensor is a device containing an
lack of initial excitation of the alternator even inductance coil and magnet. When the magnetic
after the unit has been boosted for starting. The field is distorted by the passing ring gear teeth, the
minimum specific gravity should be 1.235. Add inductance coil generates an ac electrical signal
distilled water as necessary to maintain the proper that has a voltage and frequency variation
water level. proportional to the engine RPM.
By monitoring the frequency of this signal with
Unit Wiring the microprocessor, the timing of the starter
disengagement can be precisely controlled.
Inspect the unit wiring and the wire harnesses
during scheduled maintenance inspections for If the RPM sensor fails, the starter may not
loose, chafed or broken wires to protect against disengage or engage properly and a fault code will
unit malfunctions due to open or short circuits. be generated to the microprocessor.
Testing the RPM Sensor:
Electrical Contacts The following equipment is required:
Inspect all relay contacts for pitting or corrosion
every 1,000 operating hours, and repair or replace • AC voltmeter capable of reading up to 10
as necessary. volts
• Ohmmeter
Charging System (12 Vdc) The flywheel (RPM) sensor may be checked as
Immediately after start-up, the voltmeter may follows:
show a low voltage condition on systems with 1. Install the flywheel (RPM) sensor into the
brush type alternators. This is due to a light film flywheel; bracket of the start-stop unit until it
build-up on the alternator slip rings. The film contacts the ring gear. Back out the sensor 1/2
build-up occurs primarily on units that have been turn and tighten the locknut.
sitting unused for long periods of time. The film
should disappear after a minute or two, and the
voltmeter should show a high voltage that will
continue until the battery voltage is brought back
up to normal. If the voltmeter shows low voltage
after start-up, check the alternator belt tension and
all charging circuit connections including the
battery.
Figure 12: Flywheel (RPM) Sensor
NOTE: On installations where the unit is
connected to the truck battery and both units are 2. Disconnect wires RPM+ and RPM- from the
running—it is normal for the unit to indicate a sensor.
discharge condition while the truck engine is
running because of the truck’s higher voltage
charge rate.

87
Electrical Maintenance

Glow Plugs
Glow plugs heat the combustion chamber to aid in
quick starting. The glow plugs are energized when
the microprocessor initiates unit start-up. A
defective glow plug (burned out) can be detected
Figure 13: RPM+ and RPM- Wires
by placing an external ammeter in series with the
plugs. Normal current draw is approximately
3. Place the unit in Continuous Run. Run the unit 21 to 25 amps when preheating. A current draw of
on low speed and high speed. Check the AC 21 to 25 amps means all three glow plugs are
voltage output across the sensor terminals. working. If the current draw is less than 21 amps
Use a meter with a high ohms per volt internal on Preheat, at least one glow plug is bad.
resistance. A Simpson 260, Fluke digital or
To isolate an open circuit glow plug, remove the
any good VOM will work. However, an
jumper bar and test each glow plug individually
automotive type meter may not give an
with an ohmmeter or a jumper wire and ammeter.
accurate reading because the meter may load
Each glow plug should have a resistance of
the circuit heavily and cause the voltage level
approximately 1.5 ohms or a current draw of
to appear lower than it actually is.
about 8 amps.
a. The output voltage should be 1.0 to
2.0 Vac on low speed.
b. The output voltage should be 2.0 to
2.5 Vac on high speed.
NOTE: If the voltage is slightly off, the
voltage may be increased by turning the
sensor in more, and the voltage may be
lowered by turning the sensor out more.
4. Reconnect RPM+ and RPM- wires on RPM
sensor.
If the RPM sensor passes the above test, the
sensor may be considered good. 1. Ohmmeter
If the unit is not available, an alternate less 2. 1.5 Ohms
reliable test may be performed as follows: 3. Remove Bar
Disconnect the sensor from all wires, and measure Figure 14: Glow Plug Test
the resistance across the terminals and from each
terminal to the aluminum case. The resistance With an external ammeter connected in series, a
should be 250 to 300 ohms across the terminals, shorted glow plug will show excessive current
and there should be no continuity from each flow (more than 12 amps) when the Preheat is
terminal to the case. initiated. When fuse F6 is blown, check each plug.

88
 Electrical Maintenance

Engine Reset Switch Low Oil Pressure Switch (LOP)

The engine is protected by a manual reset switch. The engine oil pressure should rise immediately
The reset switch is attached to a two sensors. One after the engine is started. The LOP will trip the
sensor switch is in the engine oil system, the other reset switch and stop the engine if the oil pressure
is in the engine cooling system. drops below 10 ± 2 psig (69 ± 14 kPa). A
continuity tester is needed to check the LOP.
If either sensor switch is grounded due to an
abnormal condition (low oil pressure, or high 1. Remove the 20A wire from the LOP.
water temperature), the reset switch will trip and
2. The continuity tester should indicate a
stop the engine in about 40 seconds.
complete circuit between the terminal and
The reset switch must be replaced if it is ground.
defective.
3. Start the engine. The tester should show an
Conditions that cause the reset switch to trip: open circuit between the terminal and ground.
• Engine coolant (water) temperature over Repair consists of replacing the LOP.
220 F (104 C).
• Engine oil pressure below 10 psig Defrost Air Switch Checkout
(69 kPa). and Adjustment
• Lack of fuel to the engine. The low oil Before testing or adjusting the air switch, check
pressure switch will cause the reset switch the clear plastic tubing and black plastic tubing to
to trip after the engine stops. the evaporator coil. Make sure they are not
obstructed or crushed. Check the probes in the
NOTE: If the On/Off switch(es) are in the
evaporator housing to be sure they are in proper
On position, if the CYCLE-SENTRY switch
position, and make sure they are not obstructed.
is in the Cont Run position, and if the engine
is not running; the low oil pressure switch 1. Remove plastic sensing tubing from both sides
will cause the reset switch to trip. of the defrost air switch.
• High pressure in the refrigeration system. 2. Disconnect one wire at switch terminal.
The low oil pressure switch will cause the Connect test light or continuity tester to the
reset switch to trip after the high pressure two terminals used on the switch.
cutout stops the engine.
3. Install test equipment (see Tool Catalog) onto
• Reset switch becomes defective. The the hose fitting on the side of the air switch
switch may get to a point where it will stamped BLACK.
open due to vibration.
4. Pressurize the hose until the continuity tester
• A ground fault in the 20 or 20A wires to indicates a completed circuit. Now read the
the sensor switches is also a possible dial of the test gauge. This is the setpoint of
cause. the air switch (correct reading is
0.70 ± 0.05 in. [17.8 ± 1.3 mm] H2O).
NOTE: A ground or shorter circuit in the
Release the pressure.
electrical system does not cause the reset
switch to pop out.

89
Electrical Maintenance

6. Repeat test procedure several times to be sure

the setting is correct.
7. Remove the test equipment. Install wire on
switch terminal and air sensing tubes on air
switch. The BLACK hose from the high
pressure or air inlet side of the evaporator coil
goes on the hose fitting on the side of the air
switch stamped BLACK. The CLEAR hose
from the low pressure or air outlet side of the
evaporator coil goes on the hose fitting on the
side of the air switch stamped CLEAR.
NOTE: Route hoses for continuous slope to
avoid condensate traps.
If too much frost continues to accumulate before
defrost, decrease the pressure setting. Turn the
adjustment screw counterclockwise.
If defrost action occurs with too little frost
accumulation, increase the pressure setting. Turn
the adjustment screw clockwise.
1. Magnetic Pressure Gauge
2. Squeeze Bulb Tool
High Capacity TherMaxTM
3. Continuity Tester
Heating System
Figure 15: Testing Air Switch
The high capacity heating system increases the
5. If the switch is out of calibration, pressurize capacity of the Heat mode by making more
the hose again until the tester indicates refrigerant available for use in the Heat mode.
0.70 in. (17.8 mm) H2O. Adjust the screw This is accomplished by adding an additional
clockwise or counterclockwise until the solenoid (TherMaxTM solenoid) to the
switch closes and the continuity tester refrigeration system which opens during the
indicates a completed circuit with the gauge beginning of the Heat mode to move the liquid
reading 0.70 in. (17.8 mm) H2O. Release the refrigerant from the condenser to the accumulator
pressure. where it can be used in the Heat mode. The
sequence of operation for the improved heating
system is from the Cool mode to the Heat mode
with Refrigerant Transfer mode to the Heat mode.
The Heat mode to Cool mode operation is the
same as in the past. The bypass check valve, and
the condenser check valve have been eliminated
from the TherMaxTM heating system.
The components that have been added to the
system are:
• the TherMaxTM solenoid
• the TherMaxTM solenoid line
1. Adjustment Screw • the receiver outlet check valve
Figure 16: Air Switch The TherMaxTM solenoid controls the flow of
refrigerant through the TherMaxTM solenoid line.
The TherMaxTM solenoid line goes from the liquid

90
 Electrical Maintenance

line just past the receiver outlet check valve to the (7K) de-energized. This reduces the load. The
accumulator inlet. The receiver outlet check valve Start Up mode is used for both diesel and electric
is located in the liquid line near the drier/receiver operation.
outlet. This check valve prevents refrigerant from
migrating back into the receiver tank and MD-II MAX Units Equipped with
condenser during the Heat mode.
a Three-Phase Electric Motor
Cool Mode and a Phase Converter That
Operates on Single-Phase
The Cool mode has not been changed in the Power
TherMaxTM heating system. The TherMaxTM
solenoid, which is normally closed, is MD-II MAX units that are ordered with the
de-energized during the Cool mode. The single-phase 220 volt electric standby option are
TherMaxTM solenoid separates the high side from equipped with a three-phase electric motor and a
the low side. When the TherMaxTM solenoid is phase conversion system. This electric motor is
closed, it does not allow liquid refrigerant to flow the same 5/4.2 hp (3.7/3.1 kW) motor used in
from the liquid line, through the TherMaxTM MD-II MAX units with a three-phase electric
solenoid line, to the accumulator. standby option. The phase conversion system
enables the three-phase electric motor to operate
Heat/Condenser Evacuation Mode using power from a single-phase power source.
The unit will run in the Condenser Evacuation NOTE: The suction pressure regulator must be
mode for two minutes before entering the Heat set at a maximum of 19 psig (131 kPa) on these
mode. This is accomplished by opening single-phase units. A higher setting will overload
(energizing) the TherMaxTM solenoid while the the electric motor. To check the suction pressure
unit is running in cool. The pressure difference regulator setting, run the unit on Defrost and
between the high pressure in the condenser and observe the suction pressure.
the low pressure in the accumulator drives much The overload relay is set at 18 amps. A higher
of the refrigerant out of the condenser and setting may not provide adequate protection.
receiver into the accumulator. The refrigerant is
then available for improved heating capacity. The Voltage taps (230 volt or 208 volt) for the
unit is placed in the Heat mode by opening transformer are located on the test strip in the
(energizing) the hot gas solenoid and closing control panel. To make sure the unit operates
(energizing) the condenser inlet solenoid. The properly, wire L1A should be connected to the
TherMaxTM solenoid remains open while the unit voltage tap that matches the voltage of the power
is in the Heat mode. The receiver outlet check source. Wire L1A is normally connected to the
valve prevents the migration of refrigerant back 208 volt tap.
into the receiver tank and condenser.
Conversion System
Defrost Mode The phase conversion system itself consists of a
The Condenser Evacuation mode is not used start system and a run system. The start system is
before the Defrost mode. The TherMaxTM energized by the high current draw that is present
solenoid, the hot gas solenoid, and the condenser while the motor is starting under a load. Once the
inlet solenoid are all energized at the same time. motor is running at normal speed and the current
The TherMaxTM solenoid remains open while the draw has dropped, the start system is de-energized
unit is in the Defrost mode. and the run system is solely responsible for the
phase shift. The run system is always connected to
Start Up Mode the motor circuit, but it does not affect the circuit
while the start system is energized because the
For the first 20 seconds when the unit is started it start capacitors have much larger capacitance and
runs in the Cool mode with the TherMaxTM dominate the run capacitors.
solenoid open and the alternator excitation circuit

91
Electrical Maintenance

Figure 17: First and Second-Phase Connections

L1 and L2 supply power directly to the first and

second windings in both sets of windings in the motor.
Start System directly to the second winding in one set. Another
branch of T2 passes through the control coil of the
The components of the start system are:
current relay and becomes T2A, which is
• a current relay connected to the second winding in the other set.
• a motor start relay A branch of T2 passes through the motor
contactor to become T3. A branch of T3 passes
• a motor start contactor
through the motor start contactor and a start
• a filter capacitor capacitor to become T3E, which is connected to
the third winding in one set. Another branch of T3
• two start capacitors (400 to 480 µF each)
passes through the motor start contactor and a
• two start bleed down resistors (180 k ohms start capacitor to become T3F, which is connected
each) to the third winding in the other set.
Single-phase power is available at L1 and L2. L1 When the motor is starting under a load, the
and L2 pass through the motor contactor and current in T1 and T2 climbs to a fairly high rate.
become L1A and L2A. L1A passes through the When the current in T2-T2A passes through the
overload relay to become T1. L2A passes through control coil of the current relay exceeds 27 amps,
the overload relay to become L2B. L2B passes the current relay is energized and its contacts
through the overload relay to become T2. close.
The three-phase motor has two separate sets of
windings with three windings in each set.
Branches of T1 are connected directly to the first
winding in each set. A branch of T2 is connected

92
 Electrical Maintenance

Figure 18: Motor Start Contactor Control Coil Circuit

7EA energizes the motor start contactor through the start

relay when the current in T2-T2A exceeds 27 amps.

Wire 7EA supplies control voltage from the unit

to the current relay at terminal 4. When the
current relay is energized, control voltage passes
through the contacts to terminal 2 and wire 7EB to
energize the motor start relay. The C3 capacitor,
which is connected in parallel with the control
coil of the motor start relay, works with the motor
start relay to act as a smoothing device to reduce
chatter in the motor start contactor.
A branch of wire 7EA also supplies control
voltage to one side of the motor start relay
contacts. When the motor start relay is energized,
control voltage passes through the closed contacts
and wire 7EB to energize the motor start
contactor.
The contacts in the motor start contactor close
when it is energized through the motor start relay.
T3E and T3F are energized and the start
capacitors provide the phase shift and boost in
power necessary to start the motor under a load.

93
Electrical Maintenance

Figure 19: Third Phase Connection During a Start

L2 supplies power to the third windings in

both sets of motor windings through the start
second windings in both sets of windings in the motor.
As the motor approaches normal running speed,
the current through T2-T2A drops. When this
current drops below 22 amps, the current relay is
de-energized. This de-energizes the motor start
relay, the motor start contactor and the start
capacitors. The start system is now disconnected
from the motor circuit and the run system
provides the phase shift necessary to operate the
motor at normal running speed.

Run System
The components of the run system are:
• a run transformer
• two run capacitors (60 µF each)
• two run bleed down resistors (560 k ohms
each).

94
 Electrical Maintenance

Figure 20: Third Phase Connection While Running Normally

L1 and L2 supplies power to the third windings in

both sets of motor windings through the run
transformer and the run capacitors.
The primary winding of the run transformer is The current relay, motor start relay, motor start
connected to L1A on one side and to L2A on the contactor, and a test point strip are located in the
other side. A branch of T3 passes through one of unit’s main control box. The test point strip is
the secondary windings on the run transformer used to diagnose problems associated with the run
and one of the run capacitors to become T3E, transformer, the run capacitors, and the start
which is connected to the third winding in one set capacitors.
of the motor windings. Another branch of T3
passes through the other secondary winding of the
run transformer and the run capacitor to become
T3F, which is connected to the third winding in
the other set of motor windings. The run
transformer and the run capacitors combine to
provide the phase shift and power needed to
operate the motor at its normal running speed.
The run transformer, run capacitors, and start
capacitors are located in a control box under the
motor pedestal. These components can be
accessed by removing the motor and pedestal
assembly from the unit’s condenser frame. The
wiring harness connected to the motor is long
enough to allow the motor and pedestal assembly
to be set beside the unit and test run if necessary.

95
Electrical Maintenance

Troubleshooting the Phase If the run current is higher than 14.5 amps in all
Conversion System three wires, check the suction pressure regulator
setting before replacing the motor. Check the
If the electric motor does not run properly, first
setting of the suction pressure regulator by
check the line voltage, the motor contactor, and
observing the suction pressure while the unit is
the motor overload relay. if these are all
running in defrost. If the suction pressure is higher
acceptable, test the electric motor to narrow down
than 19 psig (131 kPa), the suction pressure
the possible causes for the problem. See the
regulator must be adjusted or replaced.
Troubleshooting Chart for the individual
component tests. Replace the motor if currents are out of these
ranges.
Electric Motor Tests
Test 2.Run the motor with single-phase power and
Test 1. Run the motor with three-phase power. the phase conversion system connected to the
motor.
Disconnect the T1, T2, T2A, T3E, and T3F wires
from the motor and connect three-phase power Remove the electrical connection box cover on
directly to the motor. Connect L1 to leads 1 and 7, the motor, and check and record the current
connect L2 to leads 2 and 8, and connect L3 to readings in the following chart.
leads 3 and 9. Start and run the unit. Check and
record the voltage and current readings in the Wire (Motor Lead) Start Run
Current Current
following chart. T1 (1)
Wires Voltage T1 (7)
L1-L2 T2 (3)
L2-L3 T2A (9)
L3-L1 T3E (2)
T3F (8)
Wire Start Current Run Current The electric motor has two sets of windings. This
L1 test separates the sets.
L2
L3 The start current should begin at 40 to 45 amps,
and then drop off to approximately 20 amps in 1
to 3 seconds (in wires T2 and T2A). After 3
The ideal voltage is 208 to 235 volts ac and the
seconds, the run current should stabilize at 4 to 8
voltage should not vary more than 10% between
amps (in each of the six wires).
the sets of wires. If the voltages are out of these
ranges, check the power source. Circuit T2A contains the current relay, which
controls the motor start contactor. If the start
The start current should be approximately 75
current is in the proper range but the motor does
amps.
not shift to run after 3 seconds, go to Test 3. If the
The run current should not exceed 14.5 amps. start or run currents are very uneven, go to the
start or run capacitor checks in the
The current should not vary more than 10%
Troubleshooting Chart.
between wires.
NOTE: Wire L1A should be connected to the
transformer voltage tap that matches the line
voltage of the power source. High voltage on the
208 volt tap will cause high run currents.

96
 Electrical Maintenance

Test 3. The unit Starts but does not shift to the run
system.
If the motor starts correctly but the current
remains at approximately 20 amps after 3
seconds, the start system is not being
de-energized. Use the following procedure.
1. Locate the current relay in the main control
panel.
2. Disconnect the 7EA and 7EB wires.
3. Install a switch between the 7EA and 7EB
wires.
4. Close the switch between the 7EA and 7EB
wires and start the motor.
5. Wait 3 seconds and then open the switch
between the 7EA and 7EB wires.
c. If the motor does not shift to run, check for
a faulty motor start relay or a faulty motor
start contactor.
d. If the motor shifts to run, check for a
faulty current relay or an overload on the
motor.
e. If the motor shifts to run but then slows
down or stops, check for a faulty
transformer or faulty run capacitors.
See the Troubleshooting Chart for the individual
component tests.

97
Electrical Maintenance

Troubleshooting Chart
NOTE: All amperage and voltage measurements
should be taken with the unit turned On and the
motor running or attempting to start. Most of the
voltage measurements can be taken inside the
unit control box, from the components in the
high voltage tray and from the test point strip.
The voltage measurements associated with the
components under the motor pedestal should be
taken at the test point strip before checking the
components and connections under the pedestal.
The overload relay will trip if the motor does not
start shortly after the motor contactor is
energized.

Problem/Probable Cause Test/Solution

Motor Does Not Start/Low Line Voltage Check the power supply voltage at L1 and L2. The voltage
should be between 195 and 230 volts. If not, check the power
cord, the plug, and the main building power supply. / Repair as
necessary.
Motor Contactor Check to see that the motor contactor closes when energized. If
not, check the control circuit and control coil. If the contactor
closes, check the voltage between L1A and L2A and between
L1A and T3. If either voltage is low, inspect the contactor for
burned or pitted points. / Replace the contactor or points as
necessary.
Motor Overload Relay Check the overload relay to see if it is tripped. / Reset the relay.
(The correct setting for the overload relay is 18 amps.) Check
the current if the relay continues to trip. / Repair the cause of
the overload. Check the voltage between T1 and L2B and
between T1 and T2. If either voltage is low, check the overload
relay for burned or pitted points. / Replace the overload relay or
points as necessary.
Motor Faulty Test the motor by disconnecting the T1, T2, T2A, T3E, and T3F
wires from the motor and connecting three-phase power directly
to the motor. Connect L1 to leads 1 and 7, connect L2 to leads
2 and 8, and connect L3 to leads 3 and 9. If the motor starts and
runs under a load, the current should not exceed 14.5 amps per
leg. / Replace the motor if it does not run or if the current is too
high.
NOTE: With the phase converter connected to the motor, the current
per leg will vary with the line voltage and, in general, will not be the
same in all legs.

98
 Electrical Maintenance

Problem/Probable Cause Test/Solution

Current Relay Check the voltage between T1 and T2 at terminal 1 of the
current relay and between T1 and T2A at terminal 3 of the
current relay. If there is voltage between T1 and T2, but not T1
and T2A, the control coil is open. / Replace the current relay.
Check the voltage on 7EB at terminal 2 of the current relay with
unit control voltage (12 to 14 volts dc) present at 7EA on
terminal 4 of the current relay and the current relay energized
(current in T2A above 30 amps). If there is no control voltage or
low control voltage on 7EB when the current relay is energized,
the current relay is defective. / Replace the current relay.
Motor Start Relay Check the voltage on 7EC at the motor start relay with unit
control voltage (12 to 14 volts dc) present on 7EA and 7EB at
the motor start relay. If there is no control voltage or low control
voltage on 7EC, the motor start relay is defective. / Replace the
motor start relay.
Motor Start Contactor Line voltage must be present between T1 and T3 and T1 and
T31 at the motor start contactor. If not, check T3 from the motor
contactor to the start contactor. / Repair T3 as necessary.
Check the voltage between T1 and T3C and T1 and T3D with
control voltage present on 7EC at the motor start contactor.
Line voltage should be present. If no voltage is present, the
control coil of the start contactor is defective. If low voltage is
present, the points are defective. / Repair or replace the
contactor or points as necessary.

99
Electrical Maintenance

Problem/Probable Cause Test/Solution

Start Capacitors Voltage Test
With line voltage present between T1 and T3C and T1 and T3D
at the start capacitors, check the voltage between T1 and T3
and T1 and T3F. Both voltages should be within 10% of line
voltage. If one of the voltages is low, the start capacitor in that
circuit is defective. / Replace as necessary.
Current Test (NOTE: Only one of the two T3E and one of
the two T3F wires connected to the motor will carry a
current while starting.) Check the current through T3E and
T3F at the motor with an inductive ammeter during a start
attempt. The current in each wire should be 30 to 45 amps. If
one of the currents is low, the start capacitor in that circuit is
faulty. If both the currents are low, the motor start contactor did
not close. / Replace as necessary.
Motor Starts But Runs Poorly Or Slows Down
and Restarts
Run Transformer With line voltage present between L1A and L2A at the primary
winding of the run transformer, check the voltage between T3
and T3A and between T3 and T3B at the secondary windings of
the run transformer. The voltages should be 122 (+ 13/-8) volts.
If either voltage is less than 110 volts, the line voltage is low or
the run transformer is defective. / Replace as necessary.
NOTE: The transformer has a 208 volt tap and a 230 volt tap. These
taps are accessible on the test strip as L1B (208 volts) and L1C (230
volts). Wire L1A should be connected to the tap that matches the line
voltage of the power source.

100
 Electrical Maintenance

Problem/Probable Cause Test/Solution

Run Capacitors Voltage Test (This test is valid only if the motor is running at
normal speed and the motor start contactor is de-energized.)
Check the voltage between T3A and T3E and between T3B and
T3F at the test point strip. The voltages should be within 10% of
the sum of the line voltage and the secondary transformer
voltage. If the voltage is low, the run capacitor in that circuit is
defective. / Replace as necessary.
Current Test (This test is valid only if the motor is running at
normal speed and the motor start contactor is de-energized.)
NOTE: Only one of the two T3E and one of the two T3F wires
connected to the motor will carry a current while running.
NOTE: Check the current in T3E and T3F at the motor with
an inductive ammeter. Both currents should be 4 to 8 amps. If
a current is below 4 amps, the run capacitor in that circuit is
defective. / Replace as necessary.
Electric Motor Runs Hot or Loads the Diesel
Engine During Diesel Operation
Electric Motor Acting As An Induction Check the voltage at the overload relay, T1 to T2, T2 to T3, and
Alternator T3 to T1.
Check the voltage between T3E and T3F.
The voltage on any of the above pairs of wires should not
exceed 15 volts ac while the unit is running on diesel operation.
If the voltage on any of the above pairs of wires is between 500
and 700 volts ac, the electric motor is acting as an induction
alternator. To repair the unit, check the following:
1.Check the T2 and T3 circuits through the motor contactor to
make sure they are open during diesel operation. / Replace or
repair the motor contactor as necessary.
2.Check the connections between the electric motor leads and
the Thermo King wiring in the connection box on the electric
motor. Compare these connections to those indicated in the
wiring diagrams and schematics. / Repair the wiring
connections as necessary.
3.Disconnect the electric motor leads from the Thermo King
wiring at the connection box on the electric motor. Check the
wiring in the electric motor with an ohmmeter to make sure the
wires have continuity and are labeled correctly according to the
wiring diagrams and schematics. / Repair as necessary.

101
Electrical Maintenance

CAUTION: If the electric motor is being • Leads 1 and 7 together—8 to 18 amps

rewound, it must be rewound to the factory
• Leads 3 and 9 together—10 to 14 amps
specifications because this special
application requires the phases to be split. • Leads 2 and 8 together—9 to 14 amps
Full Load Current Test—Used to check the The three motor windings will exhibit a slight
overall performance of the phase conversion imbalance of currents. A difference of as much as
system. 6 amps is possible.
Use an inductive ammeter to check the current in The currents through L1 and L2 can be as high as
motor leads 1 and 7, 3 and 9, and 2 and 8. The 85 amps while starting, and as high as 23 amps
wires should have the following currents: when running at normal speed in high ambient
temperatures. High suction pressure settings can
cause high current values.

Parts List for the MD-II MAX Single-Phase Electric Motor System
Quantity Description Part Number
1 Electric Motor 104-466
1 Electric Motor Pulley 77-1980
1 Motor Contactor 44-2853
1 Overload Relay 44-6662
1 Current Relay 44-8755
1 Motor Start Relay 44-5837
1 Motor Start Contactor 44-2853
1 Transformer 44-8756
2 Start Capacitors 44-8758
2 Run Capacitors 44-8757
1 Filter Capacitor 44-8759
2 Run Capacitor Resistors 44-8760
2 Start Capacitor Resistors 44-8761

102
 Electrical Maintenance

In-Cab TG-V Controller The same interconnecting harness is used for the
Single Temperature In-Cab TG-V and the
Multi-Temp In-Cab TG-V.
A stand alone tester is available as P/N 204-831. It
will test all In-Cab TG-V Controllers.

Field Test Procedure for Single

Temperature In-Cab TG-V
Controllers
Use tester P/N 204-831.
1. Connect the end of the tester marked
“SINGLE” to the single temperature
controller.

Figure 21: Single Temperature In-Cab TG-V

Controller

(P/N 41-3305—12V No Modulation)

The In-Cab TG-V functions similarly to the

standard unit mounted TG-V. However, the
In-Cab TG-V Controller also has the following
additional features:
• Alarm Codes for Single Temperature In-Cab
TG-V.
Figure 22: Connecting Tester to Controller
Alarm Fault Condition
Code
2. Power up the controller by connecting the
tester leads to a 12 volt DC power supply.
03 Return Air Sensor Faulty
3. Press the controller’s ON key to display all
04 Discharge Air Sensor Faulty
segments.
14 Defrost Circuit Failure
a. The Turtle icon must be displayed. If not,
19 Engine Low Oil Pressure/High Water
Temperature
press the TURTLE key. Alarm Code 19 will
be recorded if the Turtle icon is not
25 Battery Charging Alternator Failure displayed.
87 Field Test Error
b. If the Alarm icon is displayed, press the
88 Microprocessor Faulty SELECT key to display the alarm and press
the ENTER key to clear the alarm.
• Power Cord LED on Model 50 Units.
4. Press the SELECT key to display the setpoint(s)
• Whisper (Low Speed) Push Button. and adjust the setpoint(s) to 80 F.
The operating manuals and the setup and NOTE: The controller must be set to display
operating manuals contain information about the temperatures in the Fahrenheit scale. The
control functions and how to customize the test WILL NOT work if the controller is
display screens. Manuals for the Single displaying temperatures in the Celsius scale.
Temperature In-Cab TG-V Controller: Operating Refer to the Controller Operating and Setup
Manual (TK 40940) and Operating and Setup Manual for information about changing the
Manual (TK 40804). displayed temperature scale.

103
Electrical Maintenance

5. With the setpoint of 80 F displayed on the

screen, press the following keys
simultaneously:
• SELECT key
• UP arrow key
• TURTLE key.
6. The display will read “FT”.
• All other icons will be Off.
• The red, Power Cord LED will begin to
flash On and off.
• All icons will then turn On for a few
seconds.
• Then the display will count from 1 to 15.
• The display will then read “PS” for pass,
or “FC” for fail.
• Press the OFF key to exit the test.

104
 Electrical Maintenance

Connector Pins for Single Temperature In-Cab TG-V

Pin # Circuit Code Harness Wire Color Code Circuit Description
1 WHT/BLK/RED
2 HGV WHT/VOIL Hot Gas Valve (Modulation Only)
3 BATT+ WHT/ORG Battery Positive
4 MV- BLUE Modulation Valve Negative (Modulation Only)
5 BATT- YELLOW Battery Negative
6 BATT+ WHT/BLK/ORG Battery Positive
7 WS WHT/BLK/YEL Whisper Relay
8 14T WHT/RED Heat Relay
9 WHT/BRN
10 ACC Accessory Wire to Truck Ignition
11 PC WHT/BLK/VOIL Power Cord (Electric Standby)
12 8B WHT/BLK/BLU CYCLE-SENTRY Input
13 10T VIOLET High Speed Relay
14 38 WHT/BLK/BRN In-Range Output
15 WHT/GRN
16 INDL WHT/GREY Alternator Charging
17 8 WHT/BRN/RED Power from On/Off Switch
18 SN WHITE Return Air Sensor
19 SN GREEN Return Air Sensor
20 BATT- WHT/BLK Battery Negative
21 11 BRN Defrost Relay Circuit
22 12 WHT/YEL Defrost Termination Switch
23 7T WHT/BLK/GRN Not Used
24 DSN BLK Discharge Air Sensor
25 PS WHT/BLU On Relay Coil
26 7K GREY Latching Circuit after 8D
27 29 ORANGE Defrost Damper Circuit
28 DSN RED Discharge Air Sensor

Figure 23: Connector on Back of Single Temperature In-Cab TG-V

105
Electrical Maintenance

106
Engine Maintenance

Engine Lubrication System Engine Oil Change

The TK 3.74 diesel engine has a pressure The engine oil should be changed according to the
lubrication system. Oil is circulated by a trochoid “Maintenance Inspection Schedule”. Drain the oil
type oil pump driven by the crankshaft timing only when the engine is hot to ensure that all the
gear and has several times the capacity required oil drains out. When changing oil, try to make
by the engine. Oil is picked up through a suction sure that the trailer is not tipped away from the
tube with a screened inlet. Oil to the rocker arm direction that the oil is supposed to flow from the
shaft flows through a tube on the outside of the oil pan. It is important to get as much of the
engine and into the head through a restrictor residual oil out as possible because most of the
fitting. dirt particles are in the last few quarts of oil to
drain out. Refill the pan with oil (see the
Oil pressure is affected by oil temperature, “Specifications” chapter) and check the dipstick
viscosity and engine speed. Subnormal oil level. Run the unit, and then recheck the oil level.
pressures usually may be traced to lack of oil,
faulty relief valve or worn bearings. The use of NOTE: Fill the crankcase slowly so oil will not
improper viscosity oil will also produce low oil run into the breather hose, thus filling up an
pressure shutdowns. open cylinder. Leaving the dipstick out while
adding engine oil will vent the crankcase.
Add oil as necessary to reach the full mark. See
Specifications chapter of this manual for correct
type of oil.

Oil Filter Change

The oil filters should be changed along with the
engine oil.
Spin-on Filters:
1. Remove the filter.
2. Apply oil to rubber ring of new filter and
AJA1521 install filter.
3. Tighten the filter until the rubber ring makes
contact, then tighten 1/2 turn more.
Figure 24: Engine Oil Pressure Switch

Engine Oil Pressure Switch

Engine oil pressure switch should rise
immediately on starting. If engine oil pressure
drops below 10 ± 2 psig (69 ± 14 kPa), the switch
closes and signals the microprocessor to stop the
engine. See Microprocessor Controller Diagnosis
Manual.

1. Spin-on Oil Filter

2. Pressure Valve Nut
3. Oil Pressure Valve

Figure 25: Oil Filter Parts

107
Engine Maintenance

Crankcase Vent The air cleaner removes abrasive material from

the air entering the engine. The air cleaner must
The crankcase vent system ducts crankcase gases be kept clean and open so that the air can pass
formed in the crankcase directly to the intake freely. If the oil has absorbed the maximum
elbow. Harmful vapors that would otherwise amount of dirt, it allows the dirt to enter the
collect in the crankcase and contaminate the oil or engine. Remove the oil cup, wash thoroughly and
escape to the outside, are now drawn back into the dry every 750 operating hours (500 hours under
engine and burned. The breather hose should be dusty conditions). Refill using the same weight oil
inspected yearly to make sure it is not plugged. used in the engine crankcase. Inspect the cleaner
body and wash in solvent when it becomes dirty.
Engine Air Cleaner
Dry Type (Optional)
Oil Bath Type A dry element air cleaner filters all of the air
A heavy duty, oil bath air cleaner filters all of the entering the engine. Excessive restriction of the
air entering the engine. Excessive restriction of air intake system affects horsepower, fuel
the air intake system reduces the flow of air to the consumption and engine life. Inspect the element
engine affecting horsepower output, fuel at regular unit service intervals.
consumption and engine life.

1. Air Intake Hose 1. Air Filter Box

2. Air Cleaner Filter 2. Air Filter
3. Clamp Assembly 3. Air Filter Cover
4. Mounting Clamps Figure 27: Dry Air Cleaner (Optional)
5. Cup

Figure 26: Oil Bath Air Cleaner

108
 Engine Maintenance

An air restriction indicator is installed in the air

intake elbow. Visually inspect the restriction
indicator periodically to assure the air filter is not
restricted. Service the air filter when the yellow
diaphragm indicates 22 in. (559 mm) of vacuum.
Press the reset button on the bottom of the
restriction indicator after servicing the air filter.

Figure 28: Air Restriction Indicator

109
Engine Maintenance

Engine Cooling System All water-cooled engines are shipped from the
factory with a mixture of 50% permanent type
General Description antifreeze concentrate and 50% water in the
engine cooling system.
The engine employs a closed, circulating type,
pressurized cooling system. Correct engine This provides the following:
temperatures are controlled and maintained by a 1. Prevents freezing down to -30 F (-34 C).
radiator, fan and thermostat. The coolant is
circulated through the system by a belt-driven 2. Retards rust and mineral scale that can cause
centrifugal pump. The pump draws the coolant engine overheating.
from the side of the radiator (large header), 3. Retards corrosion (acid) that can attack
circulates it through the cylinder block and head, accumulator tanks, water tubes, radiators and
then back to the radiator. A thermostat mounted in core plugs.
the water outlet from the cylinder head to the
radiator automatically maintains coolant 4. Provides lubrication for the water pump seal.
temperature within the specified temperature
range.

3
2

1 4

6
7
8
AJA590

1. Engine 5. Overflow Tank

2. Water Temperature Sensor 6. Drain Tubing
3. Radiator 7. Drain Cock Adaptor
4. Water Level Sensor 8. Drain Cock

Figure 29: Engine Cooling Components

110
 Engine Maintenance

Antifreeze Maintenance Procedure a. Run clear water into radiator and allow it
to drain out of the drain cock until it is
As with all equipment containing antifreeze,
clear.
periodic inspection on a regular basis is required
to verify the condition of the antifreeze. Inhibitors b. Close the block drain and install a
become worn out and must be replaced by commercially available radiator and block
changing the antifreeze. Change green or flushing agent, and operate the unit in
blue-green engine coolant every two years. accordance with instructions of the
flushing agent manufacturer.
Do not mix green or blue-green engine coolant
with ELC (red) engine coolant. c. Open the engine block and accumulator to
drain water and flushing solution.
The factory recommends the use of a 50/50%
antifreeze mixture in all units even if they are not
exposed to freezing temperatures. This antifreeze CAUTION: Avoid direct contact with hot
mixture will provide the required corrosion coolant.
protection and lubrication for the water pump.
3. Run clear water into the radiator, and allow it
to drain out of the drain cock until it is clear.
Checking the Antifreeze When water has finished draining, close drain
Check the solution concentration by using a cock.
temperature compensated antifreeze hydrometer
4. Inspect all the hoses for deterioration and the
or a refractometer designed for testing antifreeze.
hose clamp tightness. Replace if necessary.
Maintain a minimum of 50% permanent type
antifreeze concentrate and 50% water solution to 5. Loosen the water pump belt. Check the water
provide protection to -30 F (-34 C). Do not mix pump bearing for looseness.
antifreeze stronger than 68% permanent type
6. Inspect the radiator cap. Replace the cap if the
coolant concentrate and 32% water for use in
gasket shows any signs of deterioration.
extreme temperatures.
7. Mix one gallon of the appropriate permanent
Changing the Antifreeze type antifreeze concentrate and one gallon
clean water in a container to make a 50/50
1. Run the engine until it is up to operating
mixture. (Do not add antifreeze and then add
temperature. Stop the unit.
water to the unit. This procedure may not give
2. Open the engine block and completely drain a true 50/50 mixture because the exact cooling
coolant. Observe coolant color. If the coolant system capacity may not always be known).
is dirty, proceed with a, b, and c. Otherwise go
8. Refill the radiator with the 50/50 mixture.
to step 3.
CAUTION: Avoid direct contact with hot Bleeding Cooling System
coolant.
After filling the radiator, run the unit up to
operating temperature to check for overheating
and coolant level and allow the air to be purged
for a few minutes.

CAUTION: Do not remove the radiator

cap while the engine is hot.

111
Engine Maintenance

Engine Thermostat Engine Fuel System

For the best engine operation, use a 180 F (82 C) The fuel system used on the Thermo King diesel
thermostat year round. engine is a high pressure system used in
conjunction with a prechamber.
The components of the fuel system are:
• Fuel tank (may be the truck fuel tank)
• Electric Fuel pump
• Fuel filter
• Injection pump
• Injection nozzles.
A 10 psig (69 kPa) electric fuel pump pulls fuel
from the fuel tank through a fuel pump filter, then
pushes it to the fuel filter, and to the injection
pump. The prefilter is designed for diesel fuel and
is the only type that should be used.
The injection pump plungers are activated by its
own gear driven camshaft. The governor sleeve
and weight assembly is mounted on the end of the
camshaft with governor’s speed requirements
being relayed to the injection pump through a
linkage arrangement located in the front timing
cover. The injection pump raises the pressure of
the fuel and meters the correct amount of fuel to
the nozzle at the correct time. The increased fuel
1. Thermostat Housing pressure will lift the spring loaded nozzle to admit
2. Gasket fuel into the combustion chamber.
3. Thermostat The fuel system is relatively trouble free, and if
4. Water Pump properly maintained will usually not require major
service repairs between engine overhauls.
Figure 30: Water Pump Assembly and Thermostat
The most common cause of fuel system problems
is contamination. It cannot be stressed enough that
the fuel must be clean, fuel tanks must be free
from contaminants, and the fuel filter must be
changed regularly. Any time that the fuel system
is opened up, all possible precautions must be
taken to keep dirt from entering the system. This
means all fuel lines should be capped when open.
The work should be done in a relatively clean
area, if possible, and the work should be
completed in the shortest time possible.

112
 Engine Maintenance

1. Fuel Pump 5. Bypass Oil Filter

2. To Fuel Tank 6. Oil Pressure Switch
3. Oil Filter 7. Oil Pressure Gauge (Optional)
4. Fuel Filter 8. Diesel Fuel Heater (Optional)

Figure 31: Fuel and Oil System Components

113
Engine Maintenance

Thermo King recommends that any major 4. Crank the engine until fuel appears at the
injection pump or nozzle repairs be done by a nozzles. Tighten the injector lines, and start
quality diesel injection service specialty shop. The the engine.
investment in equipment and facilities to service
NOTE: Fuel will not appear at the nozzles by
these components is quite high. Therefore, this
merely running the electric pump. The
equipment is not found in most repair shops.
engine must be cranked.
The following procedures can be done under field
conditions: Draining Water from Fuel Tank
• Bleeding air from the fuel system. Water run through the system may damage the
injection pump or nozzles. Damage to the fuel
• Maintenance involving the fuel tank and filter
system will subsequently cause more expensive
system.
damage to the engine. A large accumulation of
• Speed and governor adjustments. water in the bottom of the fuel tank will stop a
diesel engine. Water should be drained off during
• Electric transfer pump replacement or repair
scheduled maintenance inspections to prevent
(10 psig [69 kPa] pump with diesel filter).
breakdowns. Drain the water off after the fuel
• Injection line replacement. tank and unit have remained idle for an hour.
• Pump timing. 1. Place a container under the fuel tank to catch
the draining water and fuel.
• Nozzle spray pattern testing and adjustment.
2. Remove the drain plug from the bottom of the
• Minor rebuilding of nozzles.
fuel tank.

Bleeding the Fuel System NOTE: Some fuel tanks have a check valve
in the drain plug fitting. Push the check
The fuel system will have to have the air bled out valve open with a small screw driver to drain
if the engine runs out of fuel, if repairs are made the tank.
to the fuel system, or air gets into the system for
any other reason. 3. Let the water and fuel drain into the container
until no water is visible in the fuel draining
NOTE: MAKE SURE to keep the fuel tank vent from the tank. If the water and fuel do not
open. If the vent becomes clogged, a partial drain freely, the vent may be plugged. If so,
vacuum develops in the tank, and this increases clean or replace the vent.
the tendency for air to enter the system.
4. Install the drain plug.
Proceed as follows:
1. Loosen the bleeder screw on the inlet fuel Fuel Filter Replacement
fitting of the injection pump. Replace the fuel filter at intervals according to the
2. Turn On the electric fuel pump. The electric Maintenance Inspection Schedule.
fuel pump is energized when the ON key is 1. Remove the filter and discard.
pushed. Tighten the bleeder screw on the
injection pump when clear flow of fuel 2. Lubricate rubber ring of new filter with fuel.
appears. 3. Install the filter and tighten until the filter is
NOTE: At initial start-up, open the bleeder slightly loose (rubber ring not making
screw at the injection pump and bleed fuel contact).
until a clear flow is noted. 4. Bleed the air from the filter by operating the
3. Loosen the injector lines on the injection electric pump until fuel bubbles appear at the
nozzles. top of filter.

114
 Engine Maintenance

5. Tighten the filter until the rubber ring makes Disassembly

contact, then tighten 1/2 turn more.
1. Remove the three screws from the cover.
Reassembly 2. Remove the filter, cover and cover gasket.
Wash the filter in cleaning solvent and blow
Place the cover gasket on the bottom cover and
out the dirt and cleaning solvent with
install the filter and cover assembly. Replace the
compressed air. Check the cover gasket and
three screws.
replace if damaged. Clean the cover.
Electric Fuel Pump If pump does not operate, check for:

1. The ground to the frame of the unit.

Operation
2. Clean and tighten electrical connections.
The electric fuel pump must be mounted next to
the fuel tank. This pump is designed to push rather 3. The pump voltage and polarity. It must be the
than pull fuel. same as the unit system.
Make sure the pump completes a good ground If pump operates but does not deliver fuel, check
for:
with the battery. The pump will not operate at less
than 9 Vdc. The pump is self priming as long as it 1. Air leaks in the fuel lines or connections.
is not higher than 30 in. (762 mm) from the fuel in
2. Kinked fuel lines or other restrictions in the
the fuel tank.
line.
3. A leaking or distorted cover gasket.
4. A dirty filter.
5. A stuck seat in the outlet fitting.

Injection Pump
Injection Pump Adjustments
When the diesel engine fails to maintain the
correct engine speed, check the following before
adjusting the speed:
1. Filter
1. Check the prefilter screen. Recheck the speed.
2. Gasket
2. Bleed air out of the fuel system. Recheck the
3. Cover
speed.
4. Screw (3)
3. Bleed air out of the nozzles. Recheck the
5. Magnet
speed.
Figure 32: Electric Fuel Pump
4. Operation of electric transfer pump.
Maintenance Make the engine speed adjustments with the
Field service is limited to cleaning the bottom engine fully warmed up.
cover and filter. The filter and cover gasket are The unit has one solenoid to control the high
replaceable. speed function. The speed of the engine should be
checked with the use of a stroboscope tachometer
(see Tool Catalog).

115
Engine Maintenance

Timing the Injection Pump to the Engine repaired recently, it may be beneficial to check
individual cylinder timing. Because the possibility
There are two different types of timing procedures
of incorrect individual cylinder timing is so
used on the engine. One procedure involves
minimal, the procedure for timing the pump to the
checking to make sure the cylinders are timed
engine will be covered first. The procedure for
correctly to each other, and the second procedure
individual cylinder timing is very similar to
times the injection pump correctly to the engine.
timing the injection pump so it will be covered
If the cylinders are not timed correctly to each
last.
other, it is of no value to time the injection pump
to the engine because one or two of the three
cylinders would be out of time. The individual CAUTION: The cylinders on the engine
plungers in the injection pump are timed to each are numbered from the flywheel end to the
other by the use of spacers in the pump plunger water pump end. The number 1 cylinder is
base. It is rare that an injection pump would next to the flywheel. The number 2
change individual cylinder timing unless it had cylinder is the center cylinder. The
been through some type of repair process, but if number 3 cylinder is next to the water
all other possible problems with a rough running pump. The timing marks on the flywheel
engine have been checked, and especially if the are matched to this system.
engine’s injection pump has been replaced or

1. TDC Mark 4. File V-Notch Here

2. Injection Timing Mark 5. Timing Mark
3. Round Notch

Figure 33: Timing Marks

1. Rotate the engine in the direction of rotation that the number 1 cylinder top dead center
(clockwise as viewed from the water pump mark on the flywheel is aligned with the
end) until the number 1 cylinder (closest to timing mark on the starter mounting plate.
flywheel) is at approximately top dead center
of the compression stroke. The valve cover
should be removed to identify the
compression stroke. Both rocker arms of the
number 1 cylinder will be loose. Check to see

116
 Engine Maintenance

NOTE: The timing marks for each of the 6. Turn the engine backwards past the injection
three cylinders are stamped 120 degrees timing mark until fuel flows from the drip
apart. Top dead center marks are identified tube.
by the number of the cylinder stamped next
7. Slowly rotate the engine in the direction of
to them. Injection timing marks are
rotation while watching the drip tube. When
unmarked. The timing marks on the engine
the fuel flow slows to approximately one drip
can be difficult to align. This is because the
every 10 to 15 seconds, check the timing
timing mark on the starter mounting plate is
marks. They should be lined up.
near the air cleaner, on the side of the plates
that faces the flywheel. It cannot be seen 8. If the timing marks did not line up, a shim or
when looking through the engine side door shims will have to be added or subtracted
opening unless you use a mirror. from the injection pump. Adding shims will
retard the injection timing, subtracting shims
The timing mark on the starter mounting
will advance the timing. Increasing or
plate is a line stamped on the side of the plate
decreasing shim thickness by 0.004 in.
facing the flywheel. To locate the timing
(0.1 mm) will change the timing by 1 degree.
mark, feel the back side of the plate 0.4 in.
(10 mm) below the center of round notch in 9. After shims have been added or subtracted,
the edge of the plate. To make it easier to recheck the timing.
align the timing marks, file a V-notch in the
10. When the injection pump has been correctly
edge of the plate in line with the timing mark
timed to the engine, remove the pump and put
on the plate.
a light coat of silicone gasket sealer on the
2. Remove the injection line from the number 1 shim pack and the pump, or dip the new shims
injector and the injection pump. Remove the in lacquer thinner to activate the sealer.
delivery valve holder, delivery valve and
11. Reinstall the pump, and torque the nuts to
spring. Care must be taken to prevent dirt
18 to 20 ft-lb (24 to 27 N•m).
from entering the fuel injection system.
Replace the delivery valve holder and delivery 12. Reinstall the delivery valve and spring.
valve. Torque the delivery valve holder to 30 ft-lb
(41 N•m).
3. Install a drip valve on the nozzle holder.
13. Reinstall the injector lines, bleed the air from
4. Activate the run solenoid and the fuel pump
the nozzles, and test run the engine.
by pushing the ON key. Make sure the
Diesel/Electric switch is in the Diesel
Timing Individual Cylinder Injection
position.
This procedure should be used when a poor
CAUTION: The 8S wire on the starter running engine has had all possible problems
motor should be disconnected. checked but continues to run badly. If the
injection pump has been repaired or replaced, the
chance of individual cylinder timing problems has
CAUTION: Loosen the injection lines on a greater possibility of occurring.
the injection nozzles of the number 2 and
3 cylinders to prevent any possibility of the To check individual cylinder timing, follow the
engine firing. pump timing procedure but instead of changing
shims to adjust pump timing, check the timing of
5. The engine should be close to the top dead number 2 and number 3 injector to the engine
center position with the plunger port in the after checking number 1. The cylinders should
pump closed. No fuel should flow from the time on their respective flywheel timing marks.
drip tube.

117
Engine Maintenance

If the injection pump plungers are not correctly Turn the engine by using the belt on the
timed to each other, the pump must be removed crankshaft pulley. Rotate the engine in the
and sent to a diesel injection equipment repair direction of rotation (clockwise as viewed
shop for calibration. next to the flywheel) from the water pump
end.
NOTE: The order of the flywheel timing marks
is 1, 2, 3, but the firing order is 1, 3, 2. This is
because the engine fires every 240 degrees of CAUTION: Make sure the fuel rack is off
crankshaft rotation. Therefore, when checking to prevent the engine from starting.
individual cylinder timing check number 1 first
a. Turn the engine so number 1 cylinder is on
then rotate the engine past number 2 to number
compression with piston to TDC. Both
3 and check number 3. Then rotate the engine
push rods should turn freely. Adjust both
past number 1 to number 2 and check number 2.
valves on number 1 cylinder.
b. Revolve the crankshaft 240 degrees to
TDC mark on number 3 cylinder, and
adjust both valves.
c. Turn the crankshaft 240 degrees to align
TDC mark of number 2 cylinder, and
adjust both valves.
d. Be sure to tighten locking nut while
holding the ball head screw in position.
3. Install the valve cover making sure that the
gasket is in position.

Fuel Limit Screw

The fuel limit screw is not adjustable. It is
Figure 34: Individual Cylinder Timing and Firing equipped with an anti-tamper cap to fulfill
Order
requirements for CARB (California Air Resources
Board) emission regulations. Service technicians
Adjust Engine Valve Clearance must be CARB certified to perform service on
1. Remove the valve cover. Torque 18 mm fuel limit screw for equipment operating in
diameter head bolts prior to adjusting the California. All other equipment can be serviced
valves: 26.8 ft-lb (36.3 N•m). Valve clearance per recent service bulletins with special tools and
should be checked after every 2000 operating procedures. California service technicians should
hours, maximum. It is very important that see your local Thermo King dealer for recent
valves be adjusted to the correct specifications bulletins.
for satisfactory engine operation. Insufficient
valve clearance will result in compression loss
and misfiring of cylinders resulting in burned
valves and seats. Excessive valve clearance
will result in noisy valve operation and
abnormal wear of the valves and rocker arms.
The intake and exhaust valves are adjusted
with the valve in the closed position.
2. The intake valve and exhaust valve are
adjusted to 0.006 to 0.010 in. (0.152 to 0.254
mm) with the temperature at 70 F (21 C).
Figure 35: Emission Control Label

118
 Engine Maintenance

Integral Fuel Solenoid When the fuel solenoid is energized, current is

applied to the coil creating an electro-magnetic
The fuel stop solenoid is located on the end of the field, which pulls the When in the “pulled-in”
fuel injection pump. position, the plunger releases tension on the
Operation of the TK 3.74 engine is controlled by governor linkage. The governor linkage then
the operation of the fuel solenoid and the throttle moves the fuel injector rack, thus controlling the
(high speed) solenoid. The fuel solenoid consists fuel flow and placing it in the “Fuel On” position.
of a spring loaded plunger and electro-magnetic Adjustments made to the throttle (high) speed
coil. When the engine is OFF, spring tension on solenoid change governor spring tension which in
the plunger maintains the plunger’s “out” turn adjust speed settings.
position. When pushed out, this causes the
governor linkage to move the injection pump rack
to the “Fuel Off” position.

1. Throttle Lever (P/N 11-6129) 6. Eye Bolt (P/N 55-2762)

2. Fuel Stop Solenoid (P/N 41-1386) 7. Boot (P/N 91-3095)
3. Low Speed Adjustment Screw 8. Throttle Solenoid (P/N 44-9181)
4. Rod (P/N 11-7817) 9. Ball Joint (11-6820)
5. Clevis Pin (11-4266)

Figure 36: Integral Fuel Solenoid Components

119
Engine Maintenance

The size of the capacitor has been changed to

1 2
increase the pull-in time from 1 second to 2
seconds. This minimizes the chance that the
pull-in coil would fail to open the fuel valve. The
integral fuel solenoid contains two coils: the
pull-in coil, and the hold-in coil. The pull-in coil
draws approximately 30 to 40 amps at 12 volts.
The hold-in coil draws approximately 1 amp at 12
volts.
The pull-in coil must be energized to move the
injection pump governor linkage to the fuel on
position. Once the injection pump governor
linkage has been moved to the fuel on position,
the hold-in coil will keep it in fuel on position
AGA337 until the 8D circuit is de-energized. The pull-in
coil must be de-energized after the 2 second
1. Four Pin Connector
pull-time.
2 Fuel Solenoid Relay (FSR)
The timer now turns off instantly because the
Figure 37: Fuel Solenoid Timer capacitor discharges through the hold-in coil in
the fuel solenoid (8D circuit). This minimizes the
Electrical Changes chance that the timer would fail to energize the
The fuel solenoid timer and fuel solenoid relay are fuel solenoid relay after the unit had been turned
located on a PC board. This improves reliability off momentarily. The earlier timer required the
and simplifies the wiring. The PC board is unit to be turned off for at least 3 seconds to
mounted on the side of the control box to the left discharge the capacitor.
to the multi-temp relay board

Figure 38: Wiring Diagram of Fuel Solenoid Timer Starting 4th Quarter 97

120
 Engine Maintenance

Troubleshooting the Integral Fuel 5. Check the CH pin in the fuel solenoid wire
Solenoid System connector for continuity to a good chassis
ground.
NOTE: The fuel solenoid pull-in coil will
require 30 to 40 amps to turn on the fuel. The a. If there is no continuity between the CH
unit’s battery must be in good condition. If the pin in the fuel solenoid wire connector and
battery has enough power to crank the engine a good chassis ground, check the black
over, it has enough power to energize the fuel (CH) wire that goes from the fuel solenoid
solenoid pull-in coil. connector to the CH terminal on the
throttle solenoid for an open circuit.
If you suspect that the engine does not run
because the fuel solenoid is not operating b. If this black (CH) wire is not open, check
correctly, use the following procedure: the other CH wire connected to the CH
terminal on the throttle solenoid for an
1. Disconnect the 20 wire from the reset switch
open circuit.
so the reset switch will not trip.
c. If there is continuity between the CH pin
2. Disconnect the 8S wire from the starter
in the fuel solenoid connector and a good
solenoid.
chassis ground, go to step 6.
3. Disconnect the fuel solenoid wire connector
6. Place a jumper wire between the CH pin in the
from the fuel solenoid.
fuel solenoid and a good chassis ground.
4. Turn the unit ON and check the voltage on the
7. Test the pull-in coil by momentarily placing a
8D pin in the fuel solenoid wire connector
jumper between the 8DP pin in the fuel
from the main wire harness. Refer to the
solenoid and the 2 terminal at the control
following illustration to identify the pins in
circuit. The fuel solenoid should make a
the wire connector and in the fuel solenoid.
definite click when the pull-in coil is
energized and should click again when the
pull-in coil is de-energized.
NOTE: The pull-in coil will draw 18 to 25
amps so do not leave the jumper connected to
the 8DP pin for more than a few seconds.
a. If the pull-in coil does not energize, check
the resistance of the pull-in coil by placing
an ohmmeter between the 8DP pin and the
CH pin in the fuel solenoid. The resistance
of the pull-in coil should be -3 to -4 ohms.
If the resistance of the pull-in coil is not in
1. Pull Coil 8DP Color: White this range, replace the fuel solenoid.
2. 8D Hold Coil Color: Red
NOTE: If the pull-in coil fails, make sure to
3. Common—Ground Color: Black CH replace the fuel solenoid relay with a
Figure 39: Fuel Solenoid Pin Identification Potter-Brumfield relay P/N 44-9111.
b. If the pull-in coil does energize, go to step
a. If battery voltage is not present on the 8D
8.
circuit, check the 8D circuit for an open or
a short. 8. Test the hold-in coil.
b. If battery voltage is present on the 8D a. Energize the hold-in coil by placing a
circuit, go to step 5. jumper between the 8D pin in the fuel
solenoid and the 2 terminal at the control
circuit.

121
Engine Maintenance

b. Momentarily energize the pull-in coil by 12. Check the voltage on the 2B circuit at the 30
placing a jumper between the 8DP pin in terminal in the fuel solenoid relay socket.
the fuel solenoid and the 2 terminal at the
a. If battery voltage is not present on the 2B
control circuit. The fuel solenoid should
circuit, check the 2B circuit for an open or
make a definite click when the pull-in coil
a short.
is energized, but should not click when the
pull-in coil is de-energized. b. If battery voltage is present on the 2B
circuit, go to step 13.
c. De-energize the hold-in coil by removing
the jumper from the 8D terminal. The fuel
solenoid should make a definite click
when the hold-in coil is de-energized.
d. If the hold-in coil does not function
properly, check the resistance of the
hold-in coil by placing an ohmmeter
between the 8D pin and the CH pin in the
fuel solenoid. The resistance of the hold-in 1. 86 Terminal—8DC Circuit
coil should be approximately 24 ohms. If
2. 30 Terminal—2B Circuit
the resistance of the hold-in coil is not in
this range, replace the fuel solenoid. 3. 85 Terminal—8D Circuit
4. 87 Terminal—8DP Circuit
e. If the hold-in coil does function properly,
go to step 9. Figure 40: Relay Socket Terminal Identification

9. Reconnect the fuel solenoid wire connector to 13. Test the relay.
the fuel solenoid.
a. Use a jumper to connect the 85 terminal
10. Remove the fuel solenoid relay from its socket on the relay to the 2 terminal at the control
and make sure the unit is turned On. circuit.
11. Check the voltage on the 8D circuit at the 85 b. Use another jumper to connect the 85
terminal in the fuel solenoid relay socket. terminal on the relay to the 2 terminal at
Refer to the following illustration to identify the control circuit.
the terminals in the relay socket.
c. If the relay does not energize, it is
a. If battery voltage is not present on the 8D defective. Replace the relay.
circuit, check the 8D circuit for an open or
a short (minimum voltage is 10 volts). d. If the relay does energize, the timer is
defective. Replace the fuel solenoid timer
b. If battery voltage is present on the 8D PC board.
circuit, go to step 12.
14. Remember to reconnect the 20 wire to the
reset switch.

122
 Engine Maintenance

Fuel Stop Solenoid Replacement NOTE: The fuel stop solenoid must be
energized when it is being installed. If it is
1. Disconnect the 20 wire from the reset switch
not, the plunger and the linkage may not line
to prevent the reset switch from tripping.
up correctly and the fuel solenoid will not
2. Disconnect the fuel stop solenoid wire function properly.
connector and remove the old fuel solenoid.
5. Place the o-ring in the groove in the end of the
3. Connect the fuel stop solenoid wire connector fuel injection pump. Make sure that the o-ring
to the new fuel solenoid. is positioned correctly during installation to
avoid damage and leaks.
4. Turn the unit on to energize the fuel stop
solenoid. 6. Install the new fuel stop solenoid.
7. Turn the unit Off and make sure to connect the
20 wire to the reset switch.

1. O-ring
2. Fuel Stop Solenoid
3. Fuel Injection Pump Groove

Figure 41: Fuel Stop Solenoid Components

123
Engine Maintenance

Belt Tensions NOTE: DO NOT attempt to remove or install

belts without adjustments. Belts that are installed
Correct belt tension is critical for proper unit by prying will fail prematurely due to internal
operation. Belts that are too loose will slip, squeal cord damage.
or whip causing excessive vibration levels and
poor unit performance. Belts that are too tight will
cause excess vibration along with premature belt
and bearing failures.

AMA414

1. Engine 6. Fan Pulley

2. Engine Clutch 7. Compressor Drive Motor (Model 50)
3. Fan Pulley 8. Compressor
4. Idler 9. Water Pump
5. Alternator
Figure 42: Belt Arrangement

WARNING: DO NOT jump belts on by

cranking the engine; personal injury may
result.

WARNING: DO NOT attempt to adjust

belts with the unit running.

124
 Engine Maintenance

NOTE: DO NOT overtighten the compressor

CAUTION: The unit may start drive belt. Belt tension should allow belt to be
automatically and at any time when the deflected 1/2 in. (13 mm) at center of span
unit On/Off switch is in the On position. without any engine movement. Over-tensioned
Units with the CYCLE-SENTRY option belts cause severe overload on the bearings. Use
start automatically in both only approved Thermo King Service Parts
CYCLE-SENTRY mode and Continuous replacement belts. They are specially designed
mode. Be sure to turn the On/Off switch for the Thermo King units.
Off before opening doors or inspecting or
working on any part of the unit. Compressor/Electric
NOTE: Tension specifications are measured Motor/Jackshaft Belt
using gauge TK 204-427. Slide the jackshaft or induction alternator away
from the compressor to tighten this belt.
Engine/Compressor Belt Belts should be tensioned cold and retensioned
Install and adjust the new engine/compressor belt cold after 10 hours of unit running.
and the new compressor/electric motor/jackshaft.
Gauge tension on new belts should be 72 ± 3 lbs
Tighten the belt tension adjuster by hand until it is (33 ± 1.4 kg). Gauge tension on used belts should
all the way down and locked into the belt tension be 67 ± 3 lbs (30 ± 1.4 kg).
stop.
This tension allows 1/2 in. (13 mm) deflection in
Tighten pulley bolt. the center of the span.
Belts should be tensioned cold and retensioned
cold after 10 hours of unit running. Water Pump Belt
Adjust tension by adding or removing shims
Gauge tension on new belts should be 75 ± 3 lbs
between pulley sheaves, until the belt allows 1/2
(34 ± 1.4 kg). Gauge tension on used belts should
in. (13 mm) of deflection at the center of the span.
be 70 ± 3 lbs (32 ± 1.4 kg).
This tension allows 1/2 in. (13 mm) deflection in
the center of the span.

1. Engine 3. Jackshaft or Electric Motor

2. Compressor
Figure 43: Belt Layout

125
Engine Maintenance

Compressor/Evaporator/Alternator Compressor/Evaporator Fan/Alternator belts, and

and Alternator/Evaporator Fan Belts 1/2 inch (13 mm) deflection at the center of the
span on the Alternator/Evaporator Fan belt.
Move the alternator upward to tighten the belts
enough to obtain 1/2 inch (13 mm) deflection at Belts should be tensioned cold and retensioned
the center of the longest span of the cold after 10 hours of running.

1. Belt Adjustment Nut 4. Pivot Bolt

2. Bracket Mounting Bolt 5. Alternator Mounting Bolt
3. Belt Adjustment Screw 6. Bracket

Figure 44: Alternator Mounting and Belt Tension Screws

126
 Engine Maintenance

Engine Speed Adjustments

Low Speed Adjustment
1. Start the unit and let it run until the engine is
warmed up.
2. Set the thermostat to make the engine run in
low speed and check the engine speed. The
engine speed should be 1625 ± 25 RPM.
3. If the engine speed is not correct, loosen the
jam nut on the low speed adjustment screw.
4. Turn the low speed adjustment screw to
change the engine speed. Turn the screw in to
increase the engine speed. Turn the screw out
to decrease the engine speed.
5. Set the engine speed at 1625 ± 25 RPM and
tighten the jam nut.

High Speed Adjustment

1. Start the unit and let it run until the engine is
warmed up.
2. Set the thermostat to make the engine run in
high speed and check the engine speed. The
engine speed should be 2425 ± 25 RPM.
3. If the engine speed is not correct, loosen the
jam nut at the end of the adjuster.
4. Unbolt the adjuster from the throttle lever and
turn to adjust the engine speed. Reinstall on
the throttle lever.
5. Set the engine speed at 2425 ± 25 RPM and
tighten the jam nut.

127
Engine Maintenance

128
Refrigeration Maintenance

Evacuation • Never attempt evacuation without a micron or

vacuum gauge. The micron gauge will help
Evacuation is Important and is Critical to System determine:
Performance!
a. If the pump is capable of pulling a deep
It has been determined through testing and system vacuum.
analysis that refrigeration systems which contain
non-condensables such as nitrogen and/or air can b. When the vacuum pump oil is
be overcharged with refrigerant when charged contaminated.
using the sight glass method. An overcharge of c. If the vacuum hoses and valves are leak
refrigerant will cause compressor damage. free.
Therefore, Thermo King recommends that all d. If the unit is leak free.
repairs to the refrigeration system include the
removal and reclamation (cleaning) of the e. How long you should evacuate the unit.
refrigerant, followed by a thorough evacuation f. That the unit is still in a deep vacuum
using the proper tools and procedures. (See before any lines are disconnected or
attached tool list and evacuation procedures.) refrigerant is added.
The primary objective of evacuation is to bring NOTE: The attached evacuation procedures
the system’s pressure to a low micron level to have been written to be used with the Thermo
ensure the removal of moisture and King Evacuation System (see Tool Catalog).
non-condensables. There are however, certain However, the principles of 3-point evacuation
other principles which must be observed. These and the use of a micron gauge during
are: evacuation should always be practiced.
• Evacuate from 3-points to access both sides of See the diagram of the Thermo King Evacuation
check valves and solenoids. Energize Station and note the location of the valves.
solenoids during evacuation to prevent
trapping of refrigerant or non-condensables. Valve #1 (V-1): Is in the open position when the
pump is running to evacuate the hoses and/or the
• Always leave service valve caps on during unit. When V-1 is closed, the pump has been
evacuation and do not exercise the valve stems isolated from the hoses and/or the unit.
while the unit is in a deep vacuum. Packing
Valve #2 (V-2): Is in the open position during unit
glands on older valves are prone to leak.
evacuation. In the closed position, V-2 isolates the
micron gauge and thermistor assembly from the
hoses and/or the unit.
Valve #3 (V-3): Is in the open position during unit
evacuation. When closed, V-3 isolates the micron
gauge and the vacuum pump from the other
evacuation hoses.
Valve #4 (V-4): Is in the open position during unit
evacuation. When closed, V-4 isolates the
evacuation hoses and the unit from the evacuation
system.

129
Refrigeration Maintenance

1 2

9 5

AGA654 6

1. V-4 6. Two Stage Vacuum Pump

2. Thermistor 7. To 110 Vac Power
3. V-3 8. Calibration Standard
4. V-2 9. Vacuum or Micron Gauge
5. V-1

Figure 45: Evacuation Station

130
 Refrigeration Maintenance

1. 100 Microns
2. 500 Microns
3. 1000 Microns
4. 2500 Microns
5. 5000 Microns
6. 20,000 Microns
7. Atmospheric Pressure
8. Calibration Adjustment Screw
9. Example: Meter needle shown at calibration position
when Calibration Standard specifies 0.15 mm Hg.

Figure 46: Vacuum Gauge

131
Refrigeration Maintenance

Set Up and Test of Evacuation • Isolate the pump from the system by closing
Equipment the proper valve. Watch the movement of the
vacuum gauge needle. If the needle continues
NOTE: See the previous two pages for the
to rise, this is an indication that a leak exists in
following discussion.
the unit or the connecting line. The leak must
1. Connect the evacuation system to a 110 Vac then be located and eliminated.
power supply. Connect a gauge manifold and
refrigerant supply to the fitting above valve
V-4. Turn the micron gauge On.
2. Close valves V-1, V-3 and V-4. Valve V-2 is
open.

Pressure Rise
3. Turn the vacuum pump On. Levels Off
4. Open valve V-1 at the pump. The micron

e
gauge needle will move to the left. (See

is
R
re
micron gauge scale diagram—previous page). Moisture

su
es
Pr
NOTE: If the vacuum pump is okay, and
there are no leaks between V-1 and V-3, the
micron gauge should show less than 500
microns. If not, locate and correct the Time
problem. Figure 48: Moisture

5. With the pump still operating, open valve V-3. • Should the needle show a pressure rise but
If the micron reading does not return to a level finally level off to practically a constant mark,
of less than 500 microns, locate and correct this is an indication that the system is vacuum
the problem before continuing. tight but is still too wet, requiring additional
dehydration and pumping time.
6. With the vacuum pump still operating, open
valve V-4. The micron level will rise 7. Evacuate hoses to 100 microns or lowest
momentarily. If the micron reading does not achievable level below 500 microns.
return to a level of less than 500 microns, 8. Once 100 microns is reached, close valve V-1
locate and correct the problem before at the pump. Turn the vacuum pump Off.
continuing.
9. Observe the micron gauge reading. The
vacuum rise should not exceed 1500 microns
in 5 minutes.
10. If the rise is above 1500 microns in 5 minutes,
check all hoses and connections for leaks.
e
Pressure Rise

is
R

Hoses with moisture present will require

e
ur

additional evacuation time to achieve

ss
re

satisfactory results.
tP
an

Leak
st

NOTE: Dirty vacuum pump oil or a defective

on
C

vacuum pump will prevent a low micron

reading. Hoses and fittings can be isolated
individually to identify leaks.

Time
Figure 47: Leak

132
 Refrigeration Maintenance

Unit Evacuation vacuum level exceeds 2000 microns after

5 minutes, a leak is present or additional
NOTE: Do not attempt to evacuate the unit until
evacuation time is required.
the evacuation equipment has been tested and its
performance has been verified. 8. If the vacuum level is acceptable, start the
pump and open valve V-1 to evacuate the
1. Prepare the unit for evacuation. Recover
pressure rise (5 minutes).
refrigerant to 0 psig (0 kPa).
9. Close valve V-1 and stop the pump. Observe
NOTE: New Federal Regulations may
the micron gauge to confirm that the system
require your recovery machine to pull the
remains in a deep vacuum. Close valve V-4.
system’s pressures lower than 0 psig [0 kPa].
The unit is ready to charge.
CAUTION: Do not attempt to evacuate a Refrigerant Leaks
unit until you are certain that the unit is
leak free. A unit with less than a full NOTE: Refer to Diagnosing Thermo King
refrigerant charge should be thoroughly Refrigeration Systems (TK 5984-3-TM) for leak
leak checked and all leaks must be detection procedures.
repaired. Use a reliable leak detector (e.g., electronic
2. Install hoses on the receiver tank, suction detector) to leak test the refrigeration system.
service valve and discharge service port. Inspect for signs of oil leakage which is the first
sign of a leak in the refrigeration system.
3. Connect a gauge manifold and refrigerant
supply to the spare access port on valve V-4. NOTE: It is normal for comprssor shaft seals to
Bottle valve closed. have a slightly oily film.
4. Start the vacuum pump and open valves V-1, Unit Charging
V-2, V-3, V-4.
NOTE: Unit must be leak checked and fully
5. Evacuate the system to 500 microns or the evacuated before charging. Before charging,
lowest achievable level between 500 and 1000 make sure that the refrigerant lines from the
microns. gauge manifold to the refrigerant supply bottle
NOTE: The presence of refrigerant in the have been evacuated or purged.
compressor oil may prevent a low micron NOTE: Refer to the diagram on the next page
reading from being achieved. The oil can for the following discussion.
continue to “outgas” for long periods of
time. If the micron level appears to stall after 1. Back seat the suction service valve. The
1/2 hour or 45 minutes between 1000 and discharge and receiver outlet valves remain
1500 microns, back seat the suction service open to port.
valve and observe the micron gauge. A sharp 2. Set the refrigerant supply bottle for liquid.
drop in the micron reading (300 to 500 Open the gauge manifold hand valve, and
microns) would indicate that refrigerant is charge liquid refrigerant until the system has
present in the oil or a leak exists in the the proper charge or until the system will take
compressor area. no more liquid. If more charge is required,
6. When the desired micron level has been charge will be added as a liquid through the
achieved (500 to 1000 microns), close valve suction service valve if more refrigerant is
V-1 at the pump. Turn the pump to Off. required.
7. Observe the reading on the micron gauge after 3. After the liquid refrigerant is added, close the
5 minutes have elapsed. The vacuum rise gauge manifold hand valve.
should not exceed 2000 microns. If the

133
Refrigeration Maintenance

4. Back seat (close) the receiver outlet valve.

Back seat the discharge service valve. Open
the suction service valve.
5. Open the refrigerant supply valve for liquid.
Open the gauge manifold hand valve.
6. Start and operate the unit with the thermostat
set for cool. Add liquid through the suction
service valve until the correct charge is
attained. Make sure that the liquid level does
not rise above the sight glass. Refer to the unit
serial plate for the correct amount of charge.

134
 Refrigeration Maintenance

1. Calibration Standard 6. V-3

2. Vacuum or Micron Gauge 7. V-1
3. V-4 8. Two Stage Vacuum Pump
4. V-2 9. To 110 Vac Power
5. Thermistor
Figure 49: Unit Charging

135
Refrigeration Maintenance

Refrigerant Charge Testing the Refrigerant Charge with

a Loaded Box
Testing the Refrigerant Charge with 1. Install a gauge manifold (optional).
an Empty Box
2. Run the unit on the Cool cycle.
If the unit has an insufficient charge of refrigerant,
the evaporator will be “starved” and the box 3. Cover at least three quarters of the condenser
temperature will rise even though the unit is to drive any excess refrigerant from the
operating. The suction pressure will drop as the condenser into the receiver tank.
refrigerant charge decreases. The charge may be 4. As the head pressure is rising, check the
determined by inspection of the refrigeration receiver tank sight glass. The ball should be
through the receiver tank sight glass with the floating. If there is no indication of refrigerant
following conditions established: in the receiver tank sight glass, the unit is low
1. Place compartment bulkheads to separate on refrigerant.
zones. NOTE: If the ball floats, there is sufficient
2. Install the gauge manifold. refrigerant in the unit for that load at that
particular box temperature. This test does
3. Run the unit on High Speed Cool until the air not determine if the unit contains a full
in the box indicates 0 F (-18 C). By allowing charge of refrigerant.
the box to leak a small amount, you will be
able to maintain 0 F (-18 C).
Checking Compressor Oil
4. The discharge or head pressure gauge should
read 275 psig (1896 kPa). The compressor oil should be checked when there
is evidence of oil loss (oil leaks) or when
If the pressure is below this, it can be raised by components in the refrigeration system have been
covering a portion of the condenser coil with a removed for service or replacement.
piece of cardboard.
To check compressor oil level with an ambient
5. The compound gauge should be indicating 13 air temperature above 50 F (10 C):
to 18 psig (90 to 124 kPa) gauge pressure.
Install a gauge manifold on the compressor.
If there is any doubt about the unit gauge,
R-134a Systems: Operate the unit on Cool with a
check the calibration.
10 psig (69 kPa) minimum suction pressure and a
6. Under these conditions, the ball in the receiver 100 psig (689 kPa) minimum discharge pressure
tank sight glass should be floating. If there is for 15 minutes or more.
no indication of refrigerant in the receiver tank R-404A Systems: Operate theunit on Cool with a
sight glass, the unit is low on refrigerant. 10 psig (69 kPa) minimum suction pressure and
185 psig (1275 kPa) minimum discharge pressure
for 15 minutes or more.
After the unit has maintained the above conditions
for 15 minutes, observe the oil level. The oil
should be 1/4 to 1/2 up in the sight glass.

136
 Refrigeration Maintenance

High Pressure Cutout (HPCO)

The high pressure cutout is located on the
discharge line. If the discharge pressure rises
above 470 psig (3241 kPa), the switch opens the
8H circuit to stop the unit. To test the switch,
rework a gauge manifold per illustration.
1. Connect the gauge manifold to the discharge
service port with a heavy duty, black jacketed
thick wall #HCA 144 hose with a 900 psig
(6204 kPa) working pressure rating.
1

AEA05

1. Add Compressor Oil Here

2. Oil Level Sight Glass
Figure 50: X214 Compressor
To check compressor oil level with an ambient air
temperature below 50 F (10 C): Run the unit
through a complete Defrost cycle. After
completing the Defrost cycle, run the unit on Cool
for ten minutes. Observe the oil level. The oil
should be 1/4 to 1/2 up in the sight glass.
If the evaporator temperature is below 32 F (0 C),
it will be necessary to force defrost. To force
1. Relief Valve
defrost, use a jumper wire and jump the number
12 wire at the defrost relay to ground. Then push 2. O-ring
the manual defrost switch. Allow evaporator 3. Adapter Tee Weather Head
temperature to rise to approximately 45 F (7.2 C).
Figure 51: High Pressure Cutout Manifold
Remove the jumper wire from the defrost relay.
If the box is empty, you can run the unit on the 2. Set the thermostat well below the box
Heat cycle instead of the Defrost cycle. temperature so that the unit will be in High
Speed Cool.
NOTE: Use refrigeration compressor oil ONLY.
R-134a and R-404A systems use a special Ester 3. Raise the discharge pressure of the
oil TK No. 203-413. compressor by blocking the condenser coil air
flow by covering the roadside condenser grille
To add oil to the compressor, pump down with a piece of cardboard.
compressor, see “Compressor Pump Down and
Checkout.” NOTE: The discharge pressure should never
be allowed to exceed a pressure of 470 psig
(3241 kPa) on R-404A systems.

137
Refrigeration Maintenance

4. Failure of the HPCO system to stop 4. Front seat discharge service valve, and
compressor operation should be investigated equalize the compressor to slightly positive.
first by checking the control circuit operation Disassemble and inspect the discharge valve
and secondly by HPCO switch replacement. plates.

Compressor Pump Down And

Checkout
1. Install a gauge manifold set on the
compressor. Open the service valves (crack
the valves off of the back seated position) to
access system pressure.
NOTE: Purge air from the gauge set.
2. Set the thermostat well below box
temperature, and run the unit in Cool mode
until temperature is stabilized (at least 5 Figure 53: Compound Gauge Indicating 20 in.
minutes). Vacuum

WARNING: Any time the discharge valve

is front seated, disconnect the unit battery
or power source to prevent accidental
compressor start-up.

Low Side Pump Down

CAUTION: Do not pull scroll compressor
into a deep vacuum to perform routine
maintenance procedures.
NOTE: Operate the unit in COOL for 2 to 5
minutes before performing the low side pump
down.
1. Unplug the hot gas bypass solenoid.
2. Install a gauge manifold to the suction service
valve and the discharge service port.
1. Suction Service Valve
2. Compound Gauge 3. Operate the unit in low speed cool.
3. High Pressure Gauge (0 to 500 psig) 4. Close the receiver tank outlet valve and allow
4. Discharge Service Valve
the low side to pump down to 0 to 5 in. Hg
vacuum (0 to -17 kPa).
Figure 52: Install Gauge Manifold

3. Close (front seat) the suction service valve. CAUTION: Do not run scroll compressor
Pump the compressor down into a deep in a vacuum for more than a few seconds.
vacuum (25 in.). Stop the unit. If the suction
5. Turn the unit Off.
pressure does not rise above 10 psig (69 kPa)
in 2 minutes, perform check procedures on the 6. Prepare to perform service on the low side by
three-way valve and the bypass check valve. If equalizing the high side and low side
the pressure does not rise, go to step 4. pressures through the gauge manifold.

138
 Refrigeration Maintenance

7. Equalize low side pressure to 1 to 2 psig (7 to 5. Operate the unit on Cool, and pump down the
14 kPa). low side to 0 in. (0 kPa) of vacuum.
NOTE: Repeat the pump down procedure if 6. Stop the unit. The condenser and suction
the pressures equalize above 20 psig pressures should remain stable, indicating no
(138 kPa). If acceptable low pressures leaks.
cannot be achieved after the third pump
7. Shift the three-way valve to heat position
down, the refrigerant must be recovered to
using relay board test. Low side gauge will
perform service on the low side.
raise slightly. High side gauge will drop to
NOTE: Valve stem MUST be back seated approximately 30 to 50 psig (207 to 345 kPa).
during normal unit operation. Gauges will equalize.
8. Plug in the hot gas bypass solenoid.
9. Open the receiver tank return outlet valve,
remove the gauges and return the unit to
normal operation.

Three-Way Valve Condenser

Pressure Bypass Check Valve
The condenser pressure bypass check valve is
built into the three-way valve. This check valve
controls the bypass flow of refrigerant gas
between the condenser inlet line and compressor
discharge line.
The check valve is closed when the unit is running
on Cool, or whenever the discharge pressure is
higher than the condenser pressure.
When the unit is running on Defrost or Heat, if the
condenser pressure is higher than the discharge
pressure, the check valve opens and the condenser
pressure is bled off until it drops to the level of the
discharge pressure. The purpose of the valve is to
1. Check Valve
improve heating/defrosting ability and three-way
valve response. 2. Heating/Defrost Position
3. Cooling Position
To check the operation of the valve:
Figure 54: Three-way Valve Condenser Pressure
1. Remove the condenser pressure bypass check Bypass Check Valve
valve cap from the three-way valve.
8. Gauges will remain in this position
2. Using a screwdriver, gently turn the check
(approximately 30 to 50 psig [207 to
valve stem in until the valve is front seated.
345 kPa]) if the three-way valve seals
3. Install a service gauge manifold set on properly toward the condenser and the
compressor. condenser pressure bypass check valve seals
properly.
4. Close (front seat) the receiver tank outlet
valve.

139
Refrigeration Maintenance

9. Back seat condenser pressure bypass check

valve stem against snap ring. Both gauges
should rise indicating the condenser pressure
bypass check valve is properly releasing
condenser pressure into the discharge tube and
evaporator.
10. Replace the cap on the condenser pressure
bypass check valve.
NOTE: Valve stem MUST be back seated
during normal unit operation.
11. Open the receiver tank return outlet valve,
remove the gauges and return the unit to
normal operation.

140
Refrigeration Service Operations
NOTE: It is generally good practice to replace Compressor
the filter-drier whenever the high side is opened
or when the low side is opened for an extended Removal
period of time.
1. Pump down the compressor and equalize the
pressure to slightly positive (1 to 2 psig
Commissioning Unit [7 to 14 kPa]).
The following procedure should be followed after 2. Loosen and remove the belts from the
any of these conditions: compressor pulley.
• The compressor has been replaced 3. Front seat the discharge and suction service
• There has been a large oil loss in the system valves. Recover the remaining refrigerant
from the compressor.
• There has been a complete clean up or flush of
the refrigeration system. 4. Unbolt the discharge valve and suction valves
from the compressor.
1. Set the thermostat to the highest setpoint.
5. Disconnect the high pressure cutout switch
If the ambient temperature is above set point wires.
range, jump power from the 2 circuit to HGS
and RHGS to allow the valves to open. 6. Remove the compressor mounting bolts.
2. Run the unit for ten minutes to allow for 7. Lift the compressor out of the unit. Keep the
wetting of the system. compressor ports covered to prevent dust, dirt,
etc., from falling into the compressor.
3. Set the thermostat for Cool (remove jumpers if
installed in the previous step). NOTE: When the compressor is removed
from the unit, the oil level should be noted,
or the oil removed from the compressor
Accumulator should be measured so that the same amount
of oil can be added before placing the
Removal replacement compressor in the unit.
1. Remove refrigerant using approved methods.
2. Unsolder the inlet and outlet refrigerant Installation
suction lines from the accumulator tank. 1. Lift the compressor into the unit and install
3. Unbolt and remove the accumulator from the the mounting bolts.
unit. 2. Install the service valves using new gaskets
soaked in refrigeration oil. Connect the high
Installation pressure cutout switch wires.
1. Place the accumulator in the unit and tighten 3. Reconnect the pilot valve and compound
the mounting bolts. pressure gauge hoses.
2. Solder the inlet and outlet suction lines to the 4. Pressurize the compressor and test for
accumulator tank. refrigerant leaks.
3. Pressurize the low side and test for refrigerant 5. If no leaks are found, evacuate the
leaks. If no leaks are found, evacuate unit. compressor. Replace the compressor/electric
motor belt and adjust the tension.
4. Charge the system with refrigerant. Check
refrigerant charge and compressor oil and add 6. Back seat the suction and discharge service
as required. valves.

141
Refrigeration Service Operations

7. Operate the unit at least 30 minutes and then Liquid Line Check Valve
inspect the oil level in the compressor. Add or
remove oil if necessary. Removal
8. Check the refrigerant charge and add 1. Remove the refrigerant charge.
refrigerant if needed.
2. Unsolder the lines and remove the check
valve.
Condenser/Radiator Coil
NOTE: Disassemble valve before unsoldering.
Removal
Installation
1. Remove the refrigerant charge by approved
methods. 1. Clean the tubes for soldering.
2. Remove the grille assembly. 2. Place the disassembled check valve in
position. Arrow on the valve body indicates
3. Drain engine coolant from the expansion tank the direction of refrigerant flow through the
and disconnect the coolant hoses from the valve.
condenser/radiator coil.
3. Solder the inlet and outlet connections. After
4. Unsolder the hot gas inlet tube and liquid the valve cools, reassemble the valve.
refrigerant line connections.
4. Pressurize the refrigeration system and test for
5. Unbolt and remove the condenser/radiator leaks.
cap.
5. If no leaks are found, evacuate the system.
Installation 6. Recharge the unit with refrigerant and check
1. Clean the tubes for soldering. the compressor oil.
2. Place the coil in the unit and install the
mounting hardware. Dehydrator (Filter-Drier)
3. Solder the inlet line and liquid line refrigerant Removal
connections.
1. Pump down the refrigeration system and
4. Pressurize the refrigeration system and test for equalize the pressure to slightly positive.
leaks. If no leaks are found, evacuate the
system. 2. Disconnect the nuts at the end of the drier.

5. Connect the coolant hoses to the radiator and 3. Loosen the mounting hardware and remove
refill the expansion tank with 50/50 ethylene the drier.
glycol/water solution.
Installation
6. Recharge the unit with refrigerant and check
the compressor oil. 1. Install the new drier and tighten the mounting
screws and nuts. Install new o-rings.
7. Reinstall the front grille.
2. Install and tighten the inlet nut to the receiver
tank outlet valve line (inlet end of drier is
labeled “IN”). Hold the drier with a back-up
wrench on the hex behind the flare fitting.
3. Release a small amount of refrigerant to purge
the air through the drier. Then tighten outlet
nut on the dehydrator to the evaporator line.

142
 Refrigeration Service Operations

4. Pressurize the system and inspect for leaks. If 2. Remove the feeler bulb from the suction line
no leaks are found, open the refrigeration clamp. Note the position of the feeler bulb on
valves and place the unit in operation. the suction line.
3. Unsolder the equalizer line from the
Evaporator Coil expansion valve.

Removal 4. Unsolder the inlet liquid line and the

distributor from the expansion valve.
1. Remove the refrigerant charge.
5. Remove the expansion valve mounting bolt
2. Remove the evaporator top panel. and remove the expansion valve from the unit.
3. Disconnect the expansion valve from the
distributor. Disconnect the air switch hoses. Installation
4. Unsolder the suction line and drain pan hot 1. Install and bolt the expansion valve assembly
gas line from the evaporator coil. in the unit.

5. Disconnect the electric heaters and high 2. Solder (95-5 Solder) the inlet liquid line and
temperature cutout switch on Model 50 units. the distributor to the expansion valve.

6. Remove the mounting bolts and slide the coil 3. Solder (95-5 Solder) the equalizer line to the
from the evaporator housing. expansion valve.
4. Clean the suction line to a bright polished
Installation condition. Install the feeler bulb clamps and
1. Place the evaporator coil in the housing. the feeler bulb on the side of the suction line
in its former position. The feeler bulb must
2. Install the mounting bolts and tighten. make good contact with the suction line or the
3. Clean the tubes for soldering. operation will be faulty. Wrap with insulating
tape.
4. Solder the suction line and drain pan hot gas
line connections to the evaporator coil. 5. Pressurize the low side and test for leaks. If no
leaks are found, evacuate the low side.
5. Connect the distributor to the expansion valve
assembly.
6. Connect the air switch hoses and install the
high temperature cutout switch and electric
heaters (Model 50).
7. Pressurize the low side and test for leaks. If no
leaks are found, evacuate the unit.
1. Suction Line
8. Open the refrigeration valves and place the 2. Capillary Bulb
unit in operation. Install the refrigerant charge
and compressor oil and add as required. 3. End View

Figure 55: Location of Expansion Valve Bulb

Expansion Valve Assembly
Removal
1. Pump down the low side and equalize pressure
to slightly positive.

143
Refrigeration Service Operations

3. Remove the mounting bolts that hold the heat

exchanger on the bulkhead.
4. Disconnect the equalizer line from the suction
line.
5. Disconnect liquid outlet line flare nut from the
expansion valve.
1. Top View 6. Note the position of the feeler bulb on the side
of the suction line. Remove the expansion
Figure 56: Completely Wrap Bulb with Tape
valve feeler bulb from the suction tube.
6. Open the refrigeration valves and place the 7. Unsolder the suction line at the evaporator coil
unit in operation. end.
7. Test the unit to see that the expansion valve is 8. Unsolder the remaining outlet suction line and
properly installed. inlet liquid line connections from the
condenser side of the bulkhead. Remove putty
Cleaning In-line Screen from around the lines before unsoldering the
1. Perform a low side pump down; bleed connections.
pressure back to 1 psig (7 kPa). 9. Lift the heat exchanger assembly out of the
2. Remove the liquid line fitting. evaporator housing.

3. A small tool with a slight hook may be needed Installation

to pull screen from the expansion valve.
1. Clean the tubes for soldering.
4. Clean the screen and reinstall.
2. Place the heat exchanger assembly in the
NOTE: Outlet screen points toward the evaporator housing and install the mounting
distributor. hardware loosely.
3. Solder liquid inlet and suction outlet line
connections on the condenser side of the
bulkhead. Seal openings through bulkhead
with putty when refrigerant lines have cooled
off.
4. Tighten the heat exchanger mounting
hardware securely.
5. Solder suction line connection to the
evaporator coil.
1. Solder-in Expansion Valve Screen
6. Connect the equalizer line flare fitting to the
2. Solder-in Type suction line and liquid outlet line flare fitting
Figure 57: Expansion Valve to the expansion valve.
7. Pressurize the low side and test for leaks. If no
Heat Exchanger leaks are found, evacuate the unit.
8. Clean the suction tube to a bright polished
Removal condition. Install the feeler bulb clamps and
1. Remove the refrigerant charge. feeler bulb on the side of the suction line in its
former position. The feeler bulb must make
2. Remove the evaporator top cover.
good contact with the suction line or operation
will be faulty. Wrap with insulating tape.

144
 Refrigeration Service Operations

9. Open the refrigeration valves and place the Pilot Solenoid

unit in operation. Install refrigerant charge.
10. Test the unit to see that the expansion valve is Removal
properly installed. 1. Pump down the low side and equalize pressure
to slightly positive.
High Pressure Cutout Switch 2. Disconnect the lines to the solenoid and
immediately cap to prevent moisture and air
Removal from entering the system.
1. Install gauge manifold set. NOTE: The lines from the three-way valve to the
2. Start the unit and pump down the low side. pilot solenoid will leak refrigerant at a high
velocity and should be capped.
3. Stop the unit.
3. Disconnect the electrical wires and remove the
4. Bleed high side to low side using gauge set. pilot solenoid.
5. Disconnect the wires and remove the high
pressure cutout switch from the discharge Installation
tube. 1. Replace the pilot solenoid in the unit.

Installation 2. Remove the caps from the lines and connect

lines to the pilot solenoid. Connect line from
1. Apply a refrigerant LoctiteTM to the threads of the three-way valve first. Connect wires to the
the high pressure cutout switch. valve.
2. Install and tighten high pressure cutout switch 3. Open the refrigeration valves and place the
and reconnect the wires. unit in operation.
3. Pressurize the refrigeration system and test for 4. Check for leaks.
leaks. If no leaks are found, evacuate the
system.
Pressure Regulator Valve
High Pressure Relief Valve Removal
Removal 1. Pump down the low side and equalize pressure
to slightly positive.
1. Remove the refrigerant charge.
2. Release remaining pressure and unsolder
2. Unscrew and remove the high pressure relief pressure regulator valve from the accumulator
valve. tank and suction tube.

Installation Installation
1. Apply a refrigerant LoctiteTM to the threads of 1. Clean the tubes for soldering.
the high pressure relief valve.
2. Place the valve in position and solder
2. Install and tighten the high pressure relief connections.
valve.
3. Pressurize the low side and check for leaks.
3. Pressurize the refrigeration system and test for
leaks. If no leaks are found, evacuate the 4. If no leaks are found, evacuate the low side.
system. 5. Open the refrigeration valves, and place the
4. Recharge the unit with refrigerant and check unit in operation. Check the refrigerant charge
the compressor oil. and add refrigerant as required.

145
Refrigeration Service Operations

Receiver Tank
Removal
1. Remove the refrigerant charge.
2. Unsolder the inlet tube from the receiver tank.
3. Unsolder the filter drier line from the receiver
tank outlet tube.
4. Unbolt the mounting brackets and remove the
receiver tank from the unit. 1. Teflon Check Valve 4. Cap
2. O-ring 5. Stem
Installation 3. Snap Ring 6. Spring
1. Place the receiver tank in the unit and install Figure 58: Condenser Pressure Bypass Check
the mounting bolts and nuts loosely. Position Valve
the receiver tank so the sight glass is clearly
visible and the outlet tube lines up. 5. Remove the spring and Teflon valve.

2. Solder the condenser inlet tube. 6. Inspect the check valve seat in the three-way
valve.
3. Solder the filter drier line to the receiver tank
outlet valve. 7. If replacement parts are needed, a kit must be
used which includes the Teflon valve, spring,
4. Tighten the receiver tank mounting hardware o-ring, valve stem and snap ring.
securely.
5. Pressurize the refrigeration system and check Installation
for leaks. If no leaks are found, evacuate the 1. Coat the o-ring with compressor oil (use same
system. type of oil that is used in the system) and
6. Recharge the unit with refrigerant. install it on the check valve stem.
2. Insert the spring into the hole in the check
Three-Way Valve Condenser valve stem and then install the Teflon check
Pressure Bypass Check Valve valve on the other end of the spring with the
Repair hole in the valve towards the spring.
3. Coat the entire assembly with compressor oil
Removal and install the assembly into the check valve
1. Remove the refrigerant charge. seat in the three-way valve.

2. Unscrew the condenser pressure bypass check CAUTION: The Teflon valve must be
valve cap from the check valve. inserted with the flat side against the valve
3. Remove the snap ring. seat to ensure proper sealing.
4. Unscrew the check valve stem by using a 4. Screw the check valve stem into the three-way
screwdriver in the slot provided. valve until the snap ring can be installed.
NOTE: Spring and valve are held in by the 5. Install the snap ring.
stem. While removing the stem, use care so 6. Unscrew (back seat) the check valve stem
the spring and valve are not lost. against the snap ring.
NOTE: Valve stem must be back seated
during normal unit operation.

146
 Refrigeration Service Operations

7. Coat sealing area in cap with compressor oil 9. Remove the piston.
(use same type of oil that is used in the
10. Remove the center section and stem assembly.
system), install and tighten the cap on the
three-way valve. 11. Inspect the following parts for wear and
damage:
8. Pressurize the refrigeration system and test for
leaks. If no leaks are found, evacuate the a. Bottom cap sealing and support areas
system.
b. Center section, sealing surface
9. Recharge the unit.
c. Top cap, sealing and support surface

Three-Way Valve Repair The following parts will be discarded:

NOTE: The three-way valve can be repaired in a. Stem assembly

the unit if leakage or damage to the Teflon seals b. All gaskets
should occur.
c. Teflon seal and o-ring
Removal 12. Remove the screen.
1. Remove the refrigerant charge. NOTE: The valve body cannot be reconditioned.
2. Clean the exterior surface of the valve. Seat positions change and improper sealing will
result.
3. Remove the 1/4 in. copper line from the
three-way valve to the pilot solenoid.
4. Loosen the four 1/4 in. Allen head screws
(do not remove); use tool (see Tool Catalog) to
break the gasket at each side of the center
section.

CAUTION: Do not force the tool into the

brass or against the bolts.

5. Unsolder the condenser line from the

condenser.
6. Remove the 4 bolts from the valve.
7. Remove the top cap and spring.
8. Remove the spring clip. Observe the slot in
the spool shaft and slide piston away from this
slot.

147
Refrigeration Service Operations

Installation
NOTE: Three-way valve kit is used to repair
three-way valves (see Tool Catalog).
After cleaning and inspecting all parts, reassemble
the valve. Clean solder off the condenser line and
condenser head with sandpaper and tubing brush.
1. Install the screen into the bottom cap.
2. Install new stem into the center section.
3. Install new gaskets on both sides of the valve
body. Dip gaskets in compressor oil (use same
type of oil that is used in the system) before
installing.
4. Install a new o-ring on the piston, then place
the Teflon seal over the o-ring.
5. Install the piston on the stem and attach with
spring clip.
NOTE: The Teflon seal will stretch when it is
installed. To prevent this from becoming
permanent (and possibly malfunction), the
top cap must be installed immediately.
6. Install the spring and top cap.
7. Line up the passageways in the cap and body.
Failure to line up the holes will result in
improper operation of the valve.
8. Install bolts and tighten in rotating sequence.
9. Solder condenser line to the condenser inlet.
10. Install pilot solenoid line and pressurize
system with refrigerant to check for leaks.
11. If there are no leaks, evacuate the system and
recharge with refrigerant.
12. Run the unit to check for proper three-way
valve operation.

1. Screw 8. O-ring
2. Top Cap 9. Gasket
3. Cap 10. Clip
4. Check Valve Assembly 11. Seat
5. Spring 12. Stem Assembly
6. Piston 13. Screen
7. Teflon Seal 14. Bottom Cap

Figure 59: Three-way Valve Assembly

148
 Refrigeration Service Operations

Compressor Pulley Removal from the tapered portion of both the pulley and
and Installation hub, and the mounting screws should be torqued
to 7 to 10 ft-lb (23 to 14 N•m). Whenever the
Units with the X214 compressor will have an two-piece pulley is removed from any type of unit
anti-seize lubricant on the tapered surfaces of the service, anti-seize lubricant should be applied to
two-piece compressor pulley. The anti-seize the outside of the tapered surface on the pulley
lubricant facilitates the installation and removal of bushing. Use one of the following recommended
the two-piece pulley. To ensure correct pulley anti-seize lubricants: Fel-Pro C5-A, Loctite 767,
alignment, all rust and/or paint should be removed Never-Seez NS-12, or Never-Seez NS-160.

1. Apply Anti-Seize Lubricant to the Tapered Surface of the Bushing Only.

2. Bushing
3. Torque Evenly to 7 to 10 ft-lb (23 to 14 N•m)
4. Clean All Rust and Paint Off These Tapered Surfaces Before Installing.
5. Pulley
Figure 60: Anti-Seize Lubricant Application

149
Refrigeration Service Operations

Oil Filter Maintenance

X214 compressors using R-134a and R-404A are
equipped with a bypass oil filter. To ensure the
system stays clean, the oil filter and filter-drier
MUST be changed every 2 years or whenever a
major service procedure has been performed.

1. Stabilizer Bracket 8. Flatwasher 15. 1/4 O-ring

2. Bracket Screw 9. Sealing Washer 16. 3/8 O-ring
3. Flatwasher 10. O-ring 17. Clamp
4. Lockwasher 11. ORS Adapter 18. Compressor Outlet Tube
5. Nut 12. 3/8 O-ring 19. ORS Adapter
6. Cylinder Head Stud 13. Compressor Inlet Tube 20. 9/16 O-ring
7. Bracket Nut 14. Filter Assembly
Figure 61: Compressor Oil Filter

150
 Refrigeration Service Operations

Compressors Shipped with R-134a The Thermo King Evacuation Station is

recommended. This station is available from
X214 Thermo King compressors are charged with
service parts under part number 204-725. See
Polyol Ester oil (POE) (TK No. 203-413). All
Truck and Trailer Service Bulletin T&T 061 for
gauge fittings are 1/4 inch fittings.
additional details.
CAUTION: Polyol Ester (POE) is the only Use only recommended vacuum pump oils and
oil for use with Thermo King units using change oil after every major evacuation. Vacuum
R-134a and R-404A. It should not be pump oils are highly refined and the use of
added to standard Thermo King units, nor contaminated oils will prevent the desired vacuum
should the standard or synthetic oil be from being obtained. Failure to follow these
added to system containing R-134a and recommendations may result in conditions that
R-404A. Combining the two oils could will destroy the vacuum pump.
result in damage to the system.
Gauge Manifold Sets
Because Polyol Ester has an affinity for moisture,
it must be kept in capped containers. In addition, Gauge manifold sets that show the correct
it should be added as the last step in system repair. pressure-temperature relationship should be used.
Rubber gloves are recommended when handling Gauge manifolds and manifold hoses used with
Polyol Ester because it may cause skin irritation. other Thermo King refrigerants maybe used but
extreme care should be taken to prevent
contamination of the R-404A systems with other
Equipment Recommendations refrigerants. Purge manifold and hoses with dry
For Use With R-404A nitrogen before using. Never use equipment that
may be contaminated with automotive type
Dedicated Equipment polyalkylene glycol (PAG) oils.

CAUTION: Equipment that has been used System Clean-up

with other refrigerants MUST NOT be
used with R-404A refrigerants. Mixing Existing clean up devices such as suction line
R-404A with other refrigerants will cause filters and compressor oil filters may be used if
contamination of the refrigerant. Using they are thoroughly cleaned and new filter
contaminated refrigerant will cause elements are installed. All standard compressor
system failure. oils must be removed from clean-up devices to
prevent contamination of R-404A systems.
Vacuum Pumps Dangerous contamination will result if other
refrigerants or standard oils are introduced to
When evacuating, a two stage three or five CFM R-404A systems.
pump is recommended. It is also recommended
that dry nitrogen be used first. Ideally, a new NOTE: For additional information on parts and
vacuum pump should be used and dedicated for supplies, consult your local Thermo King dealer
use with R-404A systems because residual and Thermo King Tool Catalog.
refrigerants may remain in used vacuum pumps.
Refrigerant Recovery
Pumps used with other Thermo King refrigerants
may be used but extreme care should be taken to Present systems can be adapted to the recovery of
prevent contamination of R-404A systems with R-404A but should be dedicated to the recovery of
other refrigerants. these refrigerants. Consult the manufacturer of
your recovery equipment for details.
An oil filter TK P/N 66-7800 is added to the
vacuum pump.

151
Refrigeration Service Operations

152
Hilliard Clutch Maintenance

Large Truck Unit Centrifugal

Clutch Change
The centrifugal clutch has three belt grooves and
its engagement speed is 600 ± 100 RPM.

Figure 62: Front View and Cross Section

153
Hilliard Clutch Maintenance

1 13
2 14

3 7
4 8
15
6 16
15
8
5 7
14
7

8
9 17
8
7
10 aea558

11

(3 belt grooves)
12

1. Screw 10. Grease Seal

2. Washer 11. Roller Bearing Inner Race
3. Snap-Ring 12. Pulley Housing
4. Ball Bearing 13. Elastic Stop Nuts (6)
5. Large & Small Spacers 14. Connector Link (6)
6. Rolling Bearing 15. Spring (6)
7. Lockwasher (12) 16. Shoe Assembly (3)
8. Bushing (6) 17. Screws (6)
9. Hub

Figure 63: Hilliard Centrifugal Clutch

154
 Hilliard Clutch Maintenance

Clutch Maintenance 3. Remove housing from hub by supporting hub

(in a minimum of three places) in spoke area,
Using an inspection mirror, inspect the clutch and pressing on the housing shaft. The inner
every 1000 hours of operation or yearly, race of the roller bearing will remain on the
whichever occurs first. If shoe wear is uneven on housing shaft.
different shoes, remove the clutch, clean the shoes
and drum, regrease bearings or replace if they are
worn. Inspect anchor bushings, shoe lining and
springs for wear and replace if necessary.

Tools Required
• Internal Retaining Ring Pliers
• 7/16 in. Wrench
• 7/32 in. Allen Wrench or 7/32 x 1/2 in. Socket
Drive
• 1/2 in. Impact Tool Figure 64: Housing Removal

• Rubber or Plastic Hammer 4. Remove the nuts from six 1/4-28 link screws
and remove screws, links, and lockwashers.
• 7/16 in. Socket or Nut Driver
5. Remove the springs and shoes.
• Arbor Press with Various Sized Arbors
6. Pull oil seal and press bearings out of hub.
• Bearing Puller
• Ratchet (Optional)
• Torque Wrench

Grease
MobilTM (Synthetic) (see Tool Catalog).

Disassembly Procedure
1. Remove retaining ring.
2. Remove the 3/8-16 flat head cap screw and
washer.
Figure 65: Bearing Removal
NOTE: This screw was installed using
LoctiteTM (see Tool Catalog) and will require NOTE: Press tool should be slightly smaller
the use of an impact tool for removal. than hub bore.
NOTE: A small amount of heat (propane or NOTE: Make sure the center of the hub is
acetylene torch with small heating tip) supported and not the outer rim of the hub,
applied to the cap screw head may be when pressing bearing out.
required to help loosen the screw.

155
Hilliard Clutch Maintenance

7. Press bushings out of hub.

Figure 66: Bushing Removal

8. Remove inner race of roller bearing from the

housing shaft.
Figure 67: Bushing Insertion
NOTE: This race had LoctiteTM applied and
was pressed in place. A puller will be *DO NOT USE SOAP OR OIL TO
required to remove it. LUBRICATE BUSHING PRIOR TO
ASSEMBLY.
NOTE: Make sure the center of the housing
is supported and not the outer drum of the 2. Remove the inner race from the roller bearing,
housing. apply a small amount of LoctiteTM (see Tool
Catalog) to race I.D. and press onto the
Assembly Procedure (Using New housing shaft, seating against the step.
Bearings and Seal)
1. Press bushings into hub side opposite flange. CAUTION: During all bearing assembly,
care must be taken to prevent LoctiteTM
NOTE: It is important to press bushings in from entering bearing.
straight.
3. Apply LoctiteTM (see Tool Catalog) to O.D. of
The bushings should also be centered in the oil seal, then press seal in end of hub opposite
hub socket leaving relatively equal amounts the flange to a depth of approximately 1/16 in.
of bushing sticking out of the hub on each below the surface.
side.
4. Apply a small amount of LoctiteTM (see Tool
A suggested simple tool for pressing in Catalog) to O.D. of roller bearing and press
bushing to hub is a 1/4 in. screw x 3 in. or 4 in. into hub bore from the flange end until seated
long and 1/4 in. nut. Thread nut onto screw against the step in bore.
approximately 3/4 to 1 in.
5. Slip large and small spacer into hub I.D.
Insert threaded end of screw into bushing. seating against the roller bearing.
Lubricate bushing by dipping in clean water
only. Then press into place.

156
 Hilliard Clutch Maintenance

6. Apply MobilTM (see Tool Catalog) grease to

roller bearing and fill cavity between large and
small spacers. A small amount of grease
should also be applied to the seal lip and space
between the seal and roller bearing.
7. Pack ball bearing with MobilTM (see Tool
Catalog) grease.
8. Apply a small amount of LoctiteTM (see Tool
Catalog) to O.D. of ball bearing and press into
hub until seated against spacer. Wipe excess
LoctiteTM from hub.
9. Install retaining ring.
10. Position shoes in a circle on flat surface and
install springs on shoes.
11. Position shoes on the hub.
12. Install 1/4-28 x 1-3/4 in. screws through links,
then external tooth 1/4 in. lockwasher. Then
slide through bushings in shoes and hub.
13. Install remaining lockwashers then links and
1/4-28 in. locknuts, torquing them to
110 ± 5 in.-lbs (12.5 ± 6 N•m).
NOTE: Shoes MUST be held tightly against
hub while nuts are tightened.
1. Roller Bearing, Pack with MobilTM (see Tool
14. Place the hub and shoe assembly into the Catalog) grease
housing and place flatwasher over the bearing.
2. Pack These Areas with MobilTM (see Tool
15. Apply Loctite (see Tool Catalog) to 3/8-16 x
TM Catalog) grease at Assembly
1 in. screw and install through washer into 3. HEX HD Cap Screw (6X), 1-4/28 UNF X 1.75
housing shaft. The housing and hub will be Long. Torque to 110 ± 5 in-lbs (12.5 ±.6 N•m)
drawn together to the proper relative position
NOTE: Shoes must be disengaged while
as the screw is tightened. Tighten the screw to
tightening 6 bolts and MUST be held
30 to 35 ft.-lbs (41 to 48 N•m).
tightly against hub while nuts are
tightened.
4. Bearing, Fill with MobilTM (see Tool Catalog)
grease Approximately 0.32 oz (70 to 80% full)
5. 3/8-16 UNC x 1.00 Long, Flat Head Socket Cap
Screw with Nylox Insert / Apply LoctiteTM (see
Tool Catalog) and Torque to 30 to 35 ft.-lb
(41 to 48 N•m)
6. Serial Nameplate

Figure 68: Clutch

157
Hilliard Clutch Maintenance

158
Structural Maintenance

Unit And Engine Mounting Condenser Coil

Bolts Clean the condenser coil during scheduled
Periodically check and tighten all unit and engine maintenance inspections by blowing compressed
mounting bolts. Torque the unit mounting bolts to air from the back side of the coil out toward the
60 ft-lb (81.3 N•m). Torque the engine mounting front of the unit (direction opposite normal air
bolts to 50 ft-lb (68 N•m). flow). Inspect the coil and fins for damage and
repair if necessary.

Defrost Damper
Check the damper during scheduled maintenance
inspections for shaft wear, end play and sealing
AMA451
against air flow.
Position the damper so that the air flow is stopped
1. Check Mounting Bolts for Tightness
top and bottom with the solenoid plunger
bottomed.
Figure 69: Check Bolts For Tightness
1. If the damper does not close completely:
Lift Points a. Energize damper solenoid by placing a
jumper wire from 12 Vdc to No. 29 wire in
The unit lifting points are noted below. Note that
the evaporator harness.
three lift points must be used.
b. If damper blade closes, proceed to step 2.
If not, proceed to step 1.c.
c. Remove the jumper wire, loosen the
evaporator outlet adjustment angle and
move so when energized, the damper will
close.
d. Retighten the adjustment angle and repeat
Figure 70: Lift Points steps a. and b.
2. If the damper blade does not seal evenly along
Unit Inspection full width of blade:
Inspect the unit during unit pretrip inspection and a. Loosen the damper bearing blocks.
scheduled maintenance inspections for loose or
broken wires or hardware, compressor oil leaks, b. Manually close the damper so the blade
or other physical damage which might affect unit makes contact at the top and bottom of the
performance and require repair or replacement of funnel, the full width of the blade.
parts. c. Retighten damper bearing blocks.

Evaporator Coil d. Lube bearing block and shaft with low

temperature grease (see Tool Catalog).
Clean the evaporator coil during scheduled
maintenance inspections by blowing compressed
air opposite normal air flow. Inspect the coil and
fins for damage and repair if necessary.

CAUTION: Air pressure should not be

high enough to damage coil fins.

159
Structural Maintenance

1 2 AEA924

Incorrect Incorrect Correct

1. Move Angle Down

2. Move Angle Up

Figure 71: Defrost Damper Adjustment

Jackshaft Assembly NOTE: There are shims between the bearing

retainer cap and the housing. These should be
The MD-II MAX 30 does not have electric saved for possible reuse during reassembly.
standby capability, therefore, the electric motor is
replaced by a jackshaft. The jackshaft assembly 4. Remove the shaft and bearings.
oil level plug should be removed, and the oil level NOTE: The oil sling retainer is pulled out by the
checked every 1000 operating hours. Check the bearing assembly on shaft.
jackshaft during the pre-trip inspection for oil
leakage. If there is any sign of leakage, remove 5. Remove the retainer cap from level plug end
the jackshaft assembly. of assembly.
Model 30 truck units are equipped with jackshafts 6. Use a punch and hammer to remove the seals
that have improved venting. This improvement and bearing cups from bearing retainer caps.
was made by using a new air vent (P/N 55-6417), 7. Use a bearing splitter or similar tool to remove
adding an oil sling retainer (P/N 77-2434), and the bearing cones from the shaft.
using fanshaft oil (P/N 203-278). The new air
vent, oil sling retainer, and fanshaft oil reduce the 8. Clean all parts in clean solvent and then
build-up of pressure inside the jackshaft. examine the bearing cups and cones for
damage.
Disassembly
1. Remove jackshaft assembly from the unit and
remove the pulleys.
2. Remove the level and fill plugs and drain oil
reservoir.
3. Remove bearing retainer cap from fill plug
1. Fill Plug and Vent 2. Oil Level Plug
end of the jackshaft assembly.
Figure 72: Jackshaft Assembly

160
 Structural Maintenance

1. End Cap
2. Oil Sling Retainer
3. Tie Band
4. Air Vent (P/N 55-6417)
5. Shaft
Figure 73: Installing Oil Sling Retainer

Reassembly 5. Install the shaft into the jackshaft housing

with oil sling retainer on the shaft with
1. Coat the edges of the oil seals with a gasket
bearing. Align the opening in the oil sling
sealant.
retainer with the air vent opening in the top of
2. Using a suitable tool, install the seals in the the jackshaft housing.
end caps. Fill the space between the seal lips
6. Use a punch and hammer to tap the oil sling
with grease. Install the assembled end cap
retainer into the jackshaft housing until it is
(seal and bearing race installed) on the oil
centered beneath the air vent opening and past
level plug end of jackshaft housing.
the housing lip that holds the outer race.
3. Place the oil sling retainer on the shaft. If the
7. Remove the tie band or hose clamp.
bearings were removed from the shaft, place
the oil sling retainer on the shaft while 8. Install the remaining end cap.
installing the bearings. If the bearings were
9. Torque the bolts to 10 ft-lb (13.6 N•m).
not removed from the shaft, press the oil sling
retainer onto the shaft through the opening in 10. Check end play of the shaft with a dial
the top of the oil sling retainer. indicator. End play should be between 0.001
to 0.005 in. 0(.025 to 0.127 mm). Change
4. Use a tie band or a hose clamp as tool to
shims if necessary.
compress the oil sling retainer enough to fit
inside the jackshaft housing. 11. Pour 3.5 oz (104 ml) of fanshaft oil P/N
203-278 into the jackshaft housing.

161
Structural Maintenance

Fanshaft Assembly
The unit is equipped with a one-piece fanshaft
assembly that contains tapered roller bearings in a
sealed oil reservoir. This assembly does not
require any maintenance. There is a level plug and
a fill plug, but they are not normally utilized
except after removal and repair of the fanshaft
assembly. The condenser end oil seal and the
evaporator end oil seal should be checked during
the pre-trip inspection for oil leakage. If there is
any sign of leakage, the fanshaft assembly should
be removed and repaired.
NOTE: The fanshaft assembly requires a special Figure 75: Removing Shaft
lubricant, TK P/N 203-278.
4. Using a punch, remove the oil seal from the
Disassembly evaporator end of the assembly. With the seal
removed, clean the housing in solvent.
1. Remove the fanshaft assembly from the unit.
Remove both oil plugs and drain the oil from
the housing.

Figure 76: Removing Oil Seal

5. Check the condition of the vent. If it is loose

or damaged, it must be repaired or replaced.
6. After all the parts are cleaned, inspect the
Figure 74: Removing Bearing Retainer Bolts bearings and bearing races for wear or
damage.
2. After draining the oil from the housing,
remove the four retaining bolts from the 7. To replace the bearings, first remove the roll
bearing retainer cap. pin that is in the center of the shaft.
3. To remove the shaft from the assembly, tap the
opposite end of the shaft with a soft hammer.
After the shaft has been removed, clean all
parts in clean solvent.

162
 Structural Maintenance

2. When replacing the bearing race on the

evaporator end of the assembly, the splash
guard will come out with the race. Reinstall
the splash guard after replacing the bearing
race.

Figure 77: Removing Roll Pin

8. With the roll pin removed, place a pipe over

the shaft and drive one bearing down until the
opposite bearing and bearing spacer release Figure 79: Installing Splash Guard
from the shaft.
3. Install a new oil seal after replacing the
9. After removing one bearing and the bearing bearing race and splash guard.
spacer, turn the shaft upside down and drive
the other bearing off, using the pipe.
10. The bearing races can now be driven out with
a punch and replaced in the same manner.

Reassembly
1. Install the new bearings on the shaft with a
pipe in the same way they were removed.

Figure 80: Installing Oil Seal

4. Place the shaft in the housing. Install a new

seal in the retainer cap. Use the original shims
and replace the o-ring if necessary.

Figure 78: Installing Bearings

Figure 81: Shims and O-ring

163
Structural Maintenance

5. Install the retainer cap assembly over the NOTE: Use ONLY Thermo King special
shaft, and then install the bolts. fanshaft grease (P/N 203-278) in this assembly.
6. Torque the bolts in a criss-cross pattern in Lock the assembly in a vise with the vent
equal steps to 80 in-lbs (9.04 N•m). facing up. Pour grease through the top plug
until it runs out of the side hole. The assembly
holds 2.2 oz (65 ml). Check the condition of
the o-ring used on the plugs and replace if
necessary. Install top and side plugs. Clean up
any spillage.
9. Place the assembly on the workbench with the
vent up. Rotate the shaft by hand. The shaft
should be free enough to rotate without having
to hold the housing.

CAUTION: When installing the fanshaft

Figure 82: Torquing Retainer Plate Bolts assembly, make sure that the vent is
mounted facing up.
7. Lock the assembly in a vise and set up a dial
indicator to read the end play. To measure the
end play, rotate the shaft while pushing in one
direction, and set the dial indicator to 0. Now
rotate the shaft and pull in the opposite
direction while reading the dial indicator. The
end play should be 0.001 to 0.005 in. (0.025 to
0.127 mm). If the end play is incorrect, use
different shims to obtain the correct end play.
Shims available from the Service Parts
Department:

0.020 in. (0.500 mm) P/N 99-4231

0.007 in. (0.177 mm) P/N 99-2902
0.005 in. (0.127 mm) P/N 99-2901 1. Oil Plug Screw with O-ring
2. Housing
3. Breather Vent
4. Oil Seal
5. Shaft
6. Sleeve
7. Pin
8. Screw with Flatwasher and Lockwasher
9. Cap and Shims
10. O-ring
11. Roller Bearing
12. Splash Guard Tube
Figure 83: Checking End Play
Figure 84: Fan Shaft Assembly
8. After the correct end play is obtained, add
grease for the bearings.

164
Mechanical Diagnosis
Condition Possible Cause Remedy
Unit switch On—nothing happens Dead battery Recharge or replace battery
Remote switch Off (optional) Turn On
Fuse open Replace
Corroded battery connections Clean and tighten
Main harness fuse blown Check for shorted main harness and
replace fuse
Unit switch On—indicator lights Battery low Replace or recharge battery
come On but engine does not
Fuse blown Replace
crank
Starter solenoid defective Repair or replace
Starter relay defective Replace relay
Corroded battery connections Clean and tighten
Starter clutch defective Replace
Starter defective Repair or replace
Engine cranks but fails to start Misadjusted fuel solenoid linkage Adjust
Fuel solenoid defective Replace solenoid
No fuel or wrong fuel in tank Fill fuel tank. After filling a
completely empty tank, first bleed
fuel system.
Engine too cold Use winter preheat procedure
Glow plugs defective Replace glow plugs
Air in fuel system Bleed fuel system. During this
operation, it can also be determined
if the fuel lines are tight and filters
clean.
Speed/run relay malfunction Check relay or unit thermostat
Insufficient compression Measure compression pressure. If
necessary, grind valves or replace
piston
Electric fuel pump not operating Check pump for running and 8 to
10 psig (55 to 69 kPa). Repair or
replace fuel pump
Injection pump incorrectly timed Adjust timing
Faulty injection nozzle(s) Repair injection nozzle or replace it
Faulty injection pump Have pump repaired

165
Mechanical Diagnosis

Condition Possible Cause Remedy

Engine stops after starting Air in injection pump Bleed fuel system
Fuel filter obstructed Replace filter element
High water temperature coolant Add coolant. Check for leaks
Low oil pressure Add oil. Check for leaks
Vent of fuel tank obstructed Remove obstruction
Electric fuel pump not operating Check pump for running and 8 to
10 psig (55 to 69 kPa). Repair or
replace fuel pump
Dry air cleaner plugged Change filter element
Fuel solenoid not energized Check run circuit
High refrigerant pressure Locate and correct cause
Engine does not reach full power Air or dirt in fuel system Adjust
Fuel line leaks Tighten connections of fuel lines. If
necessary, replace damaged lines
Speed adjustment wrong Adjust speed
Electric fuel pump does not run Check voltage. Repair or replace
pump
Fuel filter blocked Install new filter
Electric fuel pump filter dirty Clean and replace diesel filter
Delivery of fuel pump insufficient Repair or replace pump
Cylinder head gasket leaking Replace gasket
Piston rings worn, stuck or broken Replace rings
Cylinder worn Replace or bore
Leaking injection nozzle or irregular Clean and repair nozzle
injection caused by fouling
Insufficient compression pressure Check cylinder with compression
due to faulty piston or valves tester. If necessary, grind valves or
replace piston
Air filter clogged Clean air filter
Fuel tank vent clogged Unclog vent
Injection rate too low Adjust pump discharge rate
Insufficient injection pressure Readjust or replace nozzle
Pump injects too early or too late Adjust injection pump timing
Air in fuel system Bleed fuel system
Air is drawn into fuel pump Check all fuel lines and fittings
Loose governor assembly Check and repair governor
assembly
Restricted exhaust system Clean or replace restricted parts

166
 Mechanical Diagnosis

Condition Possible Cause Remedy

Engine is sooting heavily, emits Wrong fuel Drain and refill with correct fuel
thick black clouds of smoke
Clogged air intake system Clean air cleaner
(excessive fuel to air ratio)
Restricted exhaust system Clean or replace
Opening pressure of nozzle is too Repair nozzle. Replace if necessary
low or needle sticks
Injection amount too great Have pump repaired
Oil being drawn in Check oil level in oil bath air filter
Injection pump timing Check timing of injection pump
Excessive load Check drive system and engine oil
pressure
Engine knocks Insufficient air Clean air filter
Air in fuel system Bleed fuel system
Engine is cold Warm up
Fuel return line plugged Remove restriction
Injection pump not timed Retime injection pump
Injection nozzle fouled or opening Clean, repair or replace injection
pressure too low nozzle
Dirty radiator Clean radiator
Worn engine parts Overhaul engine
Engine runs hot Engine coolant is low Add coolant slowly while engine is in
operation
Dirty or plugged radiator Clean radiator
Cooling system heavily scaled Clean cooling system
Water pump leaks Repair or replace water pump
Worn or loose belt Replace belt or adjust
Cylinder head gasket leaks (bubbles Replace cylinder head gasket.
appear in radiator if cylinder gasket Correct gasket
is leaking)
Faulty thermostat Check or replace the thermostat
Faulty temperature gauge Replace gauge
Oil pressure too low or drops Insufficient oil in pan Refill oil base after correcting cause
suddenly of loss
Leak in oil line Tighten oil line fittings
Oil relief valve sticking Disassemble and clean oil pressure
regulator valve
Faulty oil pressure switch Replace if necessary
Worn oil pump, camshaft, main or Repair engine
connecting rod bearings, loose oil
gallery plug, oil in water through
crack
High oil consumption Oil leakage Check and eliminate possible
causes

167
Mechanical Diagnosis

Condition Possible Cause Remedy

Clogged air cleaner Clean air cleaner
Damaged valve seals Replace seals on valve stem
Worn valve stem or valve guides Replace valves and valve guides
Broken piston rings or cylinder bore Have engine repaired. Replace
worn or scored broken piston rings
Crankcase breather clogged Clean crankcase breather
Blue Smoke (oil consumption) Excessive oil consumption See “High oil consumption”. Repair
as necessary
White Smoke (fuel is not burning) Cold engine Allow engine to warm up
Low compression Check and eliminate possible
causes. Repair as necessary
Timing Readjust timing
Air or water in fuel Bleed system. Replace filters, clean
fuel system, drain and clean tank
and check supply tank for water.
Use known good fuel
Insufficient preheat Check glow plugs
Battery is not recharging Loose alternator belt Tighten belt
Loose connections in electrical Check all electrical connections and
system charging system
Worn brushes in alternator Repair
Voltage regulator faulty Replace
Battery defective Replace
Alternator defective Repair or replace

168
CYCLE-SENTRY Diagnosis

Condition Possible Cause Test Procedure

Unit will not energize the run Defective run relay Test run relay
relay when required
Open 7A circuit from selector switch Test 7A circuit
to run relay
Defective selector switch Test circuit from 7M to 7A on switch
in the start-stop function
Defective load temperature Check load temperature thermostat
thermostat in Continuous Run mode
Open D7 or D8 diodes Test D7 and D8 diodes
Defective CYCLE-SENTRY IV Test CYCLE-SENTRY module
module
Open 53 circuit from run relay to Test 53 circuit
CYCLE-SENTRY module
Preheat relay will not energize Defective preheat relay Test preheat relay
when required
Open 52A circuit from preheat relay Test 52A circuit
to CYCLE-SENTRY module
Open D7 or D8 diodes Test D7 or D8 diodes
Defective CYCLE-SENTRY module Test CYCLE-SENTRY module
Open CH circuit to Test CH circuit
CYCLE-SENTRY module
Open 7A circuit from selector switch Test 7A circuit
to the preheat relay
Open 2A circuit to preheat relay Test 2A circuit
(after 9-89)
Unit will not automatically crank, Defective CYCLE-SENTRY module Test CYCLE-SENTRY module
but will preheat automatically
Open 52 circuit from start relay to Test 52 circuit
starter
Open 8S circuit from start relay to Test 8S circuit
starter
Defective start relay Test start relay
Defective starter Test starter
Unit will not automatically crank, Open 8 circuit to starter relay (after Test 8 circuit
but will preheat automatically 9-89)
(continued)
Open 7A circuit to starter relay Test 7A circuit
Unit disengaged starter before Defective CYCLE-SENTRY module Test CYCLE-SENTRY module
engine is running
Low battery condition Test battery under load
Defective starter Test starter in Continuous Run
mode

169
CYCLE-SENTRY Diagnosis

Condition Possible Cause Test Procedure

Unit does not disengage starter Defective starter Test starter in Continuous Run
when engine is started mode
Defective RPM sensor Test 52A circuit
Open or grounded FS-1 or FS-2 Test FS-1 or FS-2 circuit
circuit from RPM sensor to
CYCLE-SENTRY module
Defective CYCLE-SENTRY module Test CYCLE-SENTRY module
Unit turns On and reset switch Unit fails to start (normal indication) Test for normal starting in
trips Continuous mode
Open 52 circuit from start relay to Test 52 circuit
CYCLE-SENTRY module
Open 8S circuit from start relay to Test 8S circuit
starter
Defective CYCLE-SENTRY module Test CYCLE-SENTRY module
Standard 4-mode unit has no low Defective thermostat Test thermostat
speed cool in automatic
Open diode D6 Test D6 diode
start-stop mode (unit shuts Off
after High Speed Cool
Standard 4-mode unit will not Open 29 circuit Test 29 circuit to PC board
initiate start from defrost
Open D11 diode or R9 resistor, or Test D11 diode or R9 resistor and
29T circuit on PC board 29T circuit on PC board to
thermostat
Defective thermostat Test unit thermostat
Unit will not initiate start if engine Defective block temperature Test block temperature thermostat
temperatures drop below 60.0 F thermostat
(15.5 C)
Open 8B circuit to block Test 8B circuit
temperature thermostat
Open 7A circuit from block Test 7A circuit
temperature thermostat to run relay
Unit will not stop when load Defective block temperature Test block temperature thermostat
temperature thermostat is thermostat switch switch
satisfied
Defective load temperature Test load temperature thermostat in
thermostat Continuous Run mode
Engine temperature below 120 F Check engine temperature after
(49.0 C) warm up
Battery not charged Charge battery
Defective battery sentry Replace battery sentry
Charging system faulty Correct charging system

170
Electric Standby (Optional) Diagnosis

Condition Possible Cause Remedy

Unit switch On—indicator lights Battery discharged Charge or replace battery
do not come On
Remote switch off Turn On switch (optional)
Circuit breaker or safety switch Push in button. Replace switch if
open defective
Electric motor reset switch tripping Check for short circuit in unit wiring
(high voltage)
Fuse link blown Replace fuse link
Dirty battery terminals Clean and retighten terminals
Unit switch On—indicator lights Diesel/Electric switch on Diesel Move switch to Electric position
come On but electric motor does
No standby power Provide power to unit; check power
not run
at:
1. Power source
2. Power plug
3. Motor contactor hot side
4. Motor contactor load side
(contactor closed)
5. Overload relay
6. Motor terminals
Defective motor contactor Repair or replace motor contactor
Defective low oil pressure switch Replace low oil pressure switch
Overload relay tripping Check for shorted motor windings or
wires
Defective motor Replace motor
Batteries discharged Charge ore replace batteries
Electric motor hums but does not Locked rotor (overload relay will Remove interference
run open after a period of time)
Locked compressor Repair compressor
Defective clutch on engine (locked Repair or replace clutch
up)
Low line voltage or no voltage on Bring voltage up to within 10% of
one leg motor rating
Contact chatter Low battery voltage Check voltage condition. Check
momentary voltage dip during
starting—low voltage prevents
magnet sealing
Defective or incorrect coil Replace coil
Poor contact in control circuit Check auxiliary switch contacts and
overload relay contacts. Check for
loose connections in control circuits
Poor ground on PC board Test ground circuit on PC board
Defective thermostat relay Check operation of thermostat relay

171
Electric Standby (Optional) Diagnosis

Condition Possible Cause Remedy

Contact welding or freezing Abnormal in-rush of current Check or grounds, shorts or
excessive motor load current
Low voltage Correct voltage condition. Check
momentary voltage dip during
starting
Foreign matter prevents contacts Clean contacts
from closing
Rapid cycling Check for cause of short cycling
(such as thermostat)
Short circuit Correct fault
Electric heaters do not heat— Defective heater contactor Replace contactor
(optional) indicator lights come
26 wire open Locate open and repair
On
Defective high temperature switch Replace switch or sensor
or sensor
Battery is not recharging Loose connections in electrical Check all electrical connections and
system charging system
Worn brushes in alternator Replace brushes
Voltage regulator faulty Repair or repalce regulator
Battery defective Replace battery
Alternator defective Repair or replace alternator
Loose belt Tighten belt
Dirty battery terminals Clean and retighten

172
Refrigeration Diagnosis
Rapid cycling between Cool and Heat
Unit cools in Heat and Defrost cycle

Unable to hold vacuum in low side

Unable to pull vacuum in low side
Unit heats in Refrigeration cycle

Unable to pump down system

Unit not heating or defrosting

Receiver sight glass empty
Unit operating in a vacuum

Suction line frosting back

Symptom
High suction pressure
Low suction pressure

Unit not refrigerating

No suction pressure
High head pressure
Low head pressure

Noisy compressor
No head pressure

Possible Causes

• • • • Overcharge of refrigerant
• • • • • • Shortage of refrigerant
• • • • • No refrigerant
• Air through condenser too hot (ambient)
• Air flow through condenser restricted
• • • Air through condenser too cold (ambient)
• • • Air in refrigerant system
• Condenser fan blades bent or broken
• Air short cycling around evaporator coil
• Air through evaporator restricted
• • • • Evaporator needs defrosting
• Compressor discharge valves leaking
• • Compressor seals leaking
• Too much compressor oil in system
• Faulty oil pump in compressor
• Loose compressor pulley
• Compressor bearing loose or burned out
• • • • • Broken discharge check valve in compressor
• • Expansion valve power element lost its charge

173
Refrigeration Diagnosis

Rapid cycling between Cool and Heat

Unit cools in Heat and Defrost cycle

Unable to hold vacuum in low side

Unable to pull vacuum in low side
Unit heats in Refrigeration cycle

Unable to pump down system

Unit not heating or defrosting

Receiver sight glass empty
Unit operating in a vacuum

Suction line frosting back

Symptom
High suction pressure
Low suction pressure

Unit not refrigerating

No suction pressure
High head pressure
Low head pressure

Noisy compressor
No head pressure

Possible Causes

• • • Expansion valve feeler bulb making poor contact

• • Expansion valve open too much
• • Expansion valve closed too much
• • Expansion valve needle eroded or leaking
• • • Expansion valve partially closed by ice, dirt or wax
• • • Liquid refrigerant entering compressor
• • Restricted line on the low side
• • • • Restricted line on the high side
• • • • Restricted drier
• Evaporator shutter open
• • • Evaporator shutter stuck closed
• Suction service valve back seated
• • • • • • • Faulty CIS
• • • • • Faulty Hot Gas Solenoid
• • Loose or broken electrical connections
• • • • • Thermostat or thermometer out of calibration
• • • • Suction pressure gauge out of calibration
• Leaky receiver tank outlet valve
• • DPR Valve Faulty

174
Refrigeration Diagrams

Cool Cycle—MD-II with TherMax™ Heating

1. Compressor 10. Dehydrator

2. Three-Way Valve 11. Receiver Outlet Check Valve
3. Condenser Coil 12. Accumulator Tank
4. Pilot Solenoid 13. Suction Pressure Regulator
5. Heat Solenoid 14. Heat Exchanger
6. High Pressure Relief Valve 15. Expansion Valve
7. Receiver Tank 16. Pan Heater
8. Sight Glass 17. Evaporator Coil
9. Receiver Outlet Valve

Figure 85: Cool Cycle Diagram

175
Refrigeration Diagrams

Condenser Evacuation Cycle—MD-II with TherMax™ Heating

1. Compressor 10. Dehydrator

2. Three-Way Valve 11. Receiver Outlet Check Valve
3. Condenser Coil 12. Accumulator Tank
4. Pilot Solenoid 13. Suction Pressure Regulator
5. Heat Solenoid 14. Heat Exchanger
6. High Pressure Relief Valve 15. Expansion Valve
7. Receiver Tank 16. Pan Heater
8. Sight Glass 17. Evaporator Coil
9. Receiver Outlet Valve

Figure 86: Condenser Evacuation Cycle Diagram

176
 Refrigeration Diagrams

Heat and Defrost Cycle—MD-II with TherMax™ Heating

1. Compressor 10. Dehydrator

2. Three-Way Valve 11. Receiver Outlet Check Valve
3. Condenser Coil 12. Accumulator Tank
4. Pilot Solenoid 13. Suction Pressure Regulator
5. Heat Solenoid 14. Heat Exchanger
6. High Pressure Relief Valve 15. Expansion Valve
7. Receiver Tank 16. Pan Heater
8. Sight Glass 17. Evaporator Coil
9. Receiver Outlet Valve

Figure 87: Heat and Defrost Cycle Diagram

177
Refrigeration Diagrams

178
Index
A electrical components, specifications 19
accumulator 141 electrical contacts 87
after start inspection 41 electrical control system, specifications 19
air switch, specifications 19 electrical maintenance 85
alternator 85 engine air cleaner 108
antifreeze dry type 108
maintenance procedures 111 oil bath type 108
auto start diesel operation 38 engine coolant high temperature cutout 37
engine cooling system 110
B engine fuel system 112
battery 87 engine low oil pressure cutout 37
belt engine lubrication system 107
alternator/evaporator fan 126 engine maintenance 107
compressor/electric motor/jackshaft 125 engine oil change 107
compressor/evaporator/alternator 126 engine oil dipstick 36
engine/compressor 125 engine oil pressure switch 107
water pump 125 engine operation 24
belt tension, specifications 19 engine reset switch 36, 89
belt tensions 124 engine speed adjustments 127
engine thermostat 112
C engine valve clearance 118
engine, specifications 17
charging system 87
evacuation 129
clutch maintenance 153
evaporator coil 143, 159
commissioning unit 141
evaporator high temperature protection switch 37
compressor 23, 141
expansion valve 143
compressor oil 136
compressor oil sight glass 36
compressor pulley 149 F
compressor pump down 138 fanshaft 162
condenser coil 142, 159 filter-drier 142
condenser pressure bypass check valve 139, 146 fuel filter replacement 114
continuous run operation 39 fuel limit screw 118
control circuit fuse 37 fuel solenoid 119
control system circuit breaker 37 fuel stop solenoid, replacement 123
coolant tank 36 fuel system bleeding 114
crankcase breather 108 fuel tank, draining water 114
CYCLE-SENTRY diagnosis 169
CYCLE-SENTRY diesel operation 38 G
CYCLE-SENTRY operation 24, 39 general description 23
glow plugs 88
D
defrost air switch 35, 89 H
defrost damper 159 heat exchanger 144
defrost operation 25 high pressure cutout (HPCO) 137
defrost termination switch 35 high pressure cutout switch 145
dehydrator 142 high pressure relief valve 145
diagnosis, CYCLE-SENTRY 169 hourmeters 36
diagnosis, electric standby 171
diagnosis, mechanical 165 I
diagnosis, refrigeration 173 injection pump 115
digital thermometer 36 integral fuel solenoid
electrical changes 120
E troubleshooting 121
electric fuel pump 115
electric motor reset switch 36 J
electric operation 24, 40 jackshaft 160
electric standby diagnosis 171
electric standby, specifications 20

179
Index

L low voltage 16
lift points 159 microprocessor service 14
liquid line check valve 142 refrigerant 13
loading procedure 41 refrigeration oil 14
low oil pressure switch (LOP) 89 welding 15
low side pump down 138 schematic diagrams 183
serial number locations 25
M specifications 17
maintenance inspection schedule 21 air switch 19
MD-II MAX Model 30 23 belt tension 19
MD-II MAX Model 50 23 electric standby 20
mechanical diagnosis 165 electrical components 19
modes 24 electrical control system 19
mounting bolts 159 engine 17
R-134a refrigeration system 18
O R-404A refrigeration system 18
standby power requirements 20
oil change, engine 107
thermostat 20
oil filter 150
standby power requirements, specifications 20
oil filter change 107
structural maintenance 159
oil, compressor 136
operating modes 24
overload relay 36 T
TG-V 43
P alarm codes 53
connector pins 105
phase converter 91
control keys 47
pilot solenoid 145
display information 48
post load procedure 41
display symbols 45
post trip checks 41
displaying operating data 50
preheat buzzer 37, 87
electrical 103
pressure regulator valve 145
entering setpoint 52
pretrip inspection 37
Features 23
field test 103
R guarded access mode 56
R-134a 151 overview 34
R-134a refrigeration system, specifications 18 sensor test 83
R-404A 3, 151 single temp in-cab controller 44
R-404A refrigeration system, specifications 18 standard display 48
radiator coil 142 terminal identification 80
receiver tank 146 terminal voltage chart 79
receiver tank sight glass 36 testing 74
recover refrigerant 3 TherMax 90
refrigerant charge 136 thermostat, specifications 20
refrigerant high pressure cutout 37 three-phase electric motor 91
refrigerant high pressure relief valve 37 three-way valve 139, 146, 147
refrigerant leaks 133
refrigeration diagnosis 173
refrigeration maintenance 129
U
refrigeration service operations 141 unit
remote control box description 23
overview 35 features 25
remote light indicator box 36 options 25
RPM sensor 87 photographs 27
protection devices 26
unit charging 133
S unit control box
safety precautions 13 overview 33
auto start/stop 13 unit evacuation 133
electrical hazards 14 unit indicators 36
general practices 13 unit inspection 159
high voltage 15

180
 Index

unit operation 37
unit protection devices 36

V
voltage, excessive 86

W
wiring 87
wiring diagrams 183

181
Index

182
Wiring and Schematic Diagrams Index

Dwg No. Drawing Title Page

3D98734 Cab Control MD Wiring Diagram 185
5D41583 MD w/o Thermostat Cab Control Schematic 186
5D39622 MD Cab Box Wiring Diagram 187
5D40793 MD Cab Control w/Thermostat Schematic Diagram 188
5D44893 MD-II 50 STD 1-Phase Wiring Diagram 189-190
5D44894 MD-II 50 C/S 1-Phase Wiring Diagram 191-192
5D44874 MD 50 STD 3-Phase Wiring Diagram 193-194
5D44875 MD 50 STD 3-Phase Schematic Diagram 195-196
5D44892 MD 30 STD Wiring Diagram 197-198
5D44895 MD 30 STD Schematic Diagram 199-200
5D44891 MD 30 C/S Wiring Diagram 201-202
5D44888 MD w/CYCLE-SENTRY Schematic Diagram 203-204
5D44890 MD 50 C/S 3-Phase Wiring Diagram 205-206
5D44889 MD w/CYCLE-SENTRY Schematic Diagram 207-208

183
Wiring and Schematic Diagrams Index

184
Cab Control MD Wiring Diagram

185
MD w/o Thermostat Cab Control Schematic

186
MD Cab Box Wiring Diagram

187
MD Cab Control w/Thermostat Schematic Diagram

188
MD-II 50 STD 1-Phase Wiring Diagram—Page 1 of 2

189
MD-II 50 STD 1-Phase Wiring Diagram—Page 2 of 2

190
MD-II 50 C/S 1-Phase Wiring Diagram—Page 1 of 2

191
MD-II 50 C/S 1-Phase Wiring Diagram—Page 2 of 2

192
MD 50 STD 3-Phase Wiring Diagram—Page 1 of 2

193
MD 50 STD 3-Phase Wiring Diagram—Page 2 of 2

194
MD 50 STD 3-Phase Schematic Diagram—Page 1 of 2

195
MD 50 STD 3-Phase Schematic Diagram—Page 2 of 2

196
MD 30 STD Wiring Diagram—Page 1 of 2

197
MD 30 STD Wiring Diagram—Page 2 of 2

198
MD 30 STD Schematic Diagram—Page 1 of 2

199
MD 30 STD Schematic Diagram—Page 2 of 2

200
MD 30 C/S Wiring Diagram—Page 1 of 2

201
MD 30 C/S Wiring Diagram—Page 2 of 2

202
MD w/CYCLE-SENTRY Schematic Diagram—Page 1 of 2

203
MD w/CYCLE-SENTRY Schematic Diagram—Page 2 of 2

204
MD 50 C/S 3-Phase Wiring Diagram—Page 1 of 2

205
MD 50 C/S 3-Phase Wiring Diagram—Page 2 of 2

206
MD w/CYCLE-SENTRY Schematic Diagram—Page 1 of 2

207
MD w/CYCLE-SENTRY Schematic Diagram—Page 2 of 2

208