Scribd Logo
Upload

Welcome to Scribd!

  • 140 views

    Power Vu D9858 Quick Set-Up Guide

    Uploaded by

    jose
    Manual powerVu

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Power Vu D9858 Quick Set-Up Guide

    Uploaded by

    jose
    140 views4 pages
    Manual powerVu

    Original Title

    Power Vu D9858 Quick Set-up Guide

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Manual powerVu

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    140 views4 pages

    Power Vu D9858 Quick Set-Up Guide

    Uploaded by

    jose
    Manual powerVu

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4

    PowerVu™ D9858 Advanced Receiver Transcoder

    Quick Set-up Guide

    CSN NW HD

    D9858 Rear Panel Diagram

    1. Connect the L-Band signal to RF1. 13V or 18V LNB power is only available on the RF1 port. The factory default
    setting for LNB power is OFF.
    2. Connect the ASI OUT port to an ASI device for digital tier applications. Connect the Composite Video Output to a
    video monitor and the terminal block balanced audio outputs labeled AUDIO 1 and AUDIO 2 to monitoring
    equipment.
    3. The message “Application Starting” will appear on the front panel shortly after applying power. The boot
    process approximately 1 minute for complete initialization. Wait for the front panel display to show the startup
    screen and the RED led is blinking to begin configuration.
    RF Satellite Parameters:

    1. From the Start-up menu, press MENU to display the Main Menu.
    2. Press ► to go to the SETUP menu. Press SELECT. Press ► to go to the TS INPUT menu. Press SELECT.
    3. Press SELECT for the INPUT menu. Press ► to go to the RF1 menu. Press SELECT.
    4. Press ▲ 2 times, and then press ► to NET ID. Press SELECT. Use the keypad to enter 00120. Press
    SELECT to save.
    5. Press ▲ to go to Modulation. Press SELECT. Press ▲ to change Modulation to DVB-S2; then press SELECT.
    6. Press ► to go to Rolloff and then press SELECT. Press ▲ to change Rolloff to .20 and then press SELECT.
    7. Press ▲ to go to Freq (GHz) and then press SELECT. Use the keypad to enter 03.780000 and then press
    SELECT.
    8. Press ► to go to SymRate and then press SELECT. Use keypad to enter 30.0000 and then press SELECT.
    9. Press ▲ 3 times to go to Satellite; and then press SELECT. Use the up/down arrows (▲/▼) to choose Galaxy
    5 (this is the name of the old satellite that occupied 125W). Press SELECT. 125 and W should populate the
    OrbPos and E/W fields.
    10. Press ► 3 times to go to Pol. Press SELECT. Press ▼ to set to H. Press SELECT to save
    11. Press MENU 3 times. You will see “ACQUIRING NETWORK… PLEASE WAIT”. When the network is
    acquired, the display will show “ACQUISITION SUCCESSFUL”. To save, press SELECT.
    12. Press MENU 3 times to return to the Start-up menu.

    Entry / Selection Values


    Satellite Galaxy 14
    Downlink Frequency 03.780000 GHz (3780.00 MHz)
    L-Band Frequency (equiv.) 1370.00 MHz
    Symbol Rate 30.0000 Msps
    FEC AUTO
    Modulation DVB-S2
    Rolloff 0.20
    Network ID 120
    Polarity V
    RF Input #1
    LO #1 Frequency 5.150 GHz
    Orbital Location 125 West
    Power (LNB DC Power on RF1) OFF
    Table 1 – RF Downlink Parameters

    CSN NW HD
    Virtual Channel
    14
    PID Value
    Video 510
    Audio 1 500
    Audio 2 502
    DPI 540
    ASSIGNING A PROGRAM CHANNEL TO A PE (PROGRAM ENTRY)

    For Affiliates outputting both HD and SD from a single D9858 – PE 2 must initially be assigned
    to a different channel from PE 1 to allow for ASI/MoIP output sync as the receiver cannot
    output the Network in HD and SD on the same output values for channel, PMT and PID. The
    channel to which the receiver is tuned will be changed to match at the end of Configuration #2
    or Configuration #3 and will define the video content.

    Configuration #1: Tuning the Channels

    1. At the Start-up Menu, enter 14 and press SELECT to change PE1 to 14 (NorthWest HD)
    2. Press ADV on the keypad (the diamond will move in front of PE1). Press ▼ to change to PE2.
    3. Press ADV again (the diamond will move back in front of the channel number) and enter 15 and press SELECT
    to change PE2 to 15 (NorthWest HD Alternate) – this is required to initially synch the ASI and/or MOIP1
    (MPEGoIP) outputs.
    4. For Affiliates only outputting either SD or HD on PE1 from a D9858 – PE 2 must be set to 0 (zero).
    5. Press ADV and press ▼ to return to PE1.
    6. Press ADV again to return to the channel # selection.
    7. You will ONLY be able to view programs from PE1 on the composite monitoring port (the composite monitoring
    port is automatically downconverted to an SD signal).

    Configuration #2: ENABLING the ASI OUTPUT


    - For Enabling the MOIP1 (MPEGoIP) output, go to Configuration #3
    1. From the Start-up menu, press MENU to access Main Menu.
    2. Press ► to go to the Setup menu and press SELECT.
    3. Press ▼ to go to the Outputs menu and press SELECT.
    4. Press ► to go to the TS Out menu and press SELECT.
    5. At the ASI menu, press SELECT and then press▼ to Output Mode and press SELECT.
    6. Press ▼to Transcoding and press SELECT.
    7. When “Resync All?” is displayed, press ► to Yes and then press SELECT.
    8. Press ▼to Insert Null Packets. If Insert Null Packets is set to Yes, then go to step 8. If Insert Null Packets is set
    to No, then press SELECT and press ▼to change from No to Yes. Press SELECT.
    9. Press MENU to go back to ASI. Press ► twice to DPM and press SELECT.
    10. Press SELECT to access the Global menu.
    11. At ASI, press SELECT to Resync. When “Resync?” is displayed, press ► to Continue and then press SELECT.
    12. Press APPLY. Failure to perform this step will result with no ASI output.
    13. At “Save Changes?” press SELECT to save.
    14. Press MENU 6 times to return to the Start-up menu.
    15. If you are also enabling the MOIP1 (MPEGoIP) output, then skip steps 17, 18, and 19 below and proceed to
    Configuration #3 below.
    16. Once at the start-up menu, press ADV and then press▼ to change to PE2. Press ADV again and type 14 to
    change PE2 to 14 (NorthWest HD).
    17. Press ADV and press ▼ to return to PE1.
    18. Press ADV again to return to the channel # selection.
    Configuration #3: ENABLING the MOIP1 (MPEGoIP) OUTPUT
    - For Enabling ASI go to Configuration #2
    1. From the Start-up Menu, press MENU to access Main Menu.
    2. Press ► to Setup menu and press SELECT.
    3. Press ▼ to Outputs menu and press SELECT.
    4. Press ► to TS Out menu and press SELECT.
    5. Press ►to MOIP1 and press SELECT. Press ▼ to Output Mode and press SELECT.
    6. Press ▼to Transcoding and press SELECT.
    7. When “Resync All?” is displayed, press ► to Yes and then press SELECT.
    8. Press ▼ to Insert Null Packets. If Insert Null Packets is set to Yes, then go to step 8. If Insert Null Packets is set
    to No, then press SELECT and press ▼ to change from No to Yes. Press SELECT.
    9. Press ▼ three times to DestAddr. Press SELECT and enter the desired destination IP address for the MPEGoIP
    output. Press SELECT to save.
    10. Press ► to UDPPort and press SELECT. Enter the desired UDP port and press SELECT to save.
    11. Press MENU to go back to MOIP1; then press ► to DPM and press SELECT.
    12. Press SELECT to access the Global menu. Press ► to MOIP1.
    13. Press SELECT to Resync. When “Resync?” is displayed, press ► to Continue and then press SELECT.
    14. Press APPLY. Failure to perform this step will result with no ASI output.
    15. At “Save Changes?” press SELECT to save.
    16. Press MENU 6 times to return to the Start-up menu.
    17. Once at the start-up menu, press ADV and then press▼ to change to PE2. Press ADV again and type 14 to
    change PE2 to 14 (NorthWest HD).
    18. Press ADV and press ▼ to return to PE1.
    19. Press ADV again to return to the channel # selection.

    TO AUTHORIZE RECEIVER

    During normal business hours – 8:30 AM to 5:30 PM M-F Eastern, please contact NBCU Affiliate Broadcast
    Operations for authorization by calling (201) 735-3700. You must provide the UA number and TID of your D9858
    located in Main Menu: ABOUT.
    1. From the Start-up Menu, press MENU to access MAIN MENU.
    2. Press ► twice to ABOUT. Press SELECT twice. Make a note of the Tracking ID.
    3. Press ▼ twice to Master UA and note the 7 digits after the zeros – 000-123-4567-x (note that the Master UA
    is PE 1 and that PE 2 is one higher than PE 1 – i.e. 000-123-4568-x).
    4. Press MENU three times to return to the Start-up menu.

    If you need assistance, or experience any difficulty setting up or authorizing your receiver, please contact:

    NBCU AFFILIATE BROADCAST OPERATIONS (201) 735-3700

    You might also like