Product Information

PRODUCT SERIES: DPG 2000

n t y
DPG2100 e n l
u m O
o c e
D n c
re
Low Cost
The DPG2100 controller has widespread
l ed e
l
application for many diesel and gas engine
e f
User Friendly/Operator Adjustable
o
generator sets. This microprocessor based,
R
tr
digital controller performs across a wide speed .25% Precision Frequency Control
range offering extremely fast engine response l
on c
to speed or load change and stable isochronous a Superior Temperature Stability
operation.
n c
o ri Reverse Battery Protection
U t
The controller also features an LED which

isand gain
provides an operating status symbol.
set up is simple with only speed
Controller
9 - 30 VDC Input Voltage Range
H for both panel
adjustments. The unit is suitable
and engine mounting and
o r uses a magnetic Actuator Compatibility:

F
pickup for speed reference.
The DPG2100 has an internal FAILSAFE that
DYNA 2000
DYNA 2500
instantly reacts to: Power Flow gas valves
DYNA 7000
· Interruption of DC power returns DYNA 70025
actuator to minimum fuel position.
· Loss of speed reference signal cuts Other Models Available:
power to the actuator for spring DPG 2200 - for Parallel Isochronous Generators
return to minimum fuel position. DPG 2300 - for Off-Highway Applications

Barber-Colman
1354 Clifford Avenue Europe Japan - Ranco Japan
P.O. Box 2940 Barber-Colman GmbH Shiozaki Bldg. 7-1
Loves Park, IL 61132 Am Neuen Rheinhafen 4 2-chome
USA D-67346 Speyer Hirakawa-Cho,Chiyoda-Ku
Tel: (815) 637-3000 Germany Tokyo, 102, Japan
Fax:(815) 877-0150 Tel: 06232-29903 Tel: 3261-4293
www.dynaproducts.com Fax: 06232-299155 Fax: 3264-4691 DYNA 298
Controller Specifications Controller Adjustment: Set speed using
increase/decrease pushbuttons and Gain
Operating Voltages: (270 degree adjustment)
9 VDC minimum to 30 VDC maximum
Temperature Stability: .007 Hz @ 70°C
Maximum output current: 7 amps continous,
14 amps ten seconds maximum Input signal voltage from mag pickup:
2.5 VAC RMS minimum during cranking
Steady State Speed Band: ± .25% over temperature
range of -40°F to +180°F, -40°C to +85°C Models (Replaces):
DPG-2101 (DYN1-1070x)
Ambient Operating Temperature: DPG-2102 (DYN1-1072x)
-40°F to +180°F, -40°C to +85°C DPG-2104 (DYN1-1078x)

Sealing: Oil, water, and dust resistant via conformal Diagnostic LED:
coating and die cast enclosure Off - no power or reverse battery exists
1Hz - power on
Connections: Euro-style terminal strip
On - service required
n t
3Hz - receiving speed signal
y
Weight: .6lbs, .28kilograms e - CAUTION -
n l
Input signal: 0-1000 Hz startup u m O
As a safety measure, the engine should be equipped with an
independent overspeed shutdown device in the event of failure
1000-11,000 Hz normal operation c e
which may render the governor inoperative.
o
Mechanical Vibration: Suitable for mounting per D n c
Controller designed for negative ground systems only.

e
Engine mounted controllers must not exceed temperature

ed r
SAE J1455; 1 to 500Hz, 5G amplitude specification. Engine mounting is typically done on the flywheel

l e
housing where temperatures do not exceed specifications.

l ef
Input signal frequency from mag pickup:
- NOTE -
o
Freq. (HZ)= (Engine rpm *flywheel teeth) ÷ 60 sec. Barber-Colman believes that all information provided herein is
R
tr
correct and reliable and reserves the right to update at any time.

l
Barber-Colman does not assume any responsibility for its use

on a unless otherwise expressly undertaken.

i c
nc o r
U t
is
H
o r
F

DYNA 298