CALCUL DES STRUCTURES ACIER

----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 1 POTEAU
PIECE: 20 STRUCTURE POINT: 2 COORDONNEE: x = 0.10 L = 0.60 m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 39 ELU/3=17*1.35 + 18*1.50 + 2*0.90 17*1.35+18*1.50+2*0.90
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 500

h=50.0 cm gM0=1.00 gM1=1.00
b=20.0 cm Ay=72.07 cm2 Az=59.87 cm2 Ax=115.52 cm2
tw=1.0 cm Iy=48198.50 cm4 Iz=2141.69 cm4 Ix=89.00 cm4
tf=1.6 cm Wely=1927.94 cm3 Welz=214.17 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 110.13 kN My,Ed = 27.41 kN*m Mz,Ed = -0.07 kN*m Vy,Ed = 0.12 kN
Nc,Rd = 2714.77 kN My,Ed,max = 272.85 kN*m Mz,Ed,max = -0.63 kN*m Vy,c,Rd = 977.83 kN
Nb,Rd = 1554.72 kN My,c,Rd = 453.07 kN*m Mz,c,Rd = 50.33 kN*m Vz,Ed = 45.69 kN
Vz,c,Rd = 812.35 kN
Mb,Rd = 408.95 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = 0.00 Mcr = 792.45 kN*m Courbe,LT - c XLT = 0.79
Lcr,upp=6.00 m Lam_LT = 0.76 fi,LT = 0.80 XLT,mod = 0.90
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 6.00 m Lam_y = 0.22 Lz = 6.00 m Lam_z = 1.04
Lcr,y = 4.20 m Xy = 1.00 Lcr,z = 4.20 m Xz = 0.57
Lamy = 20.56 kzy = 0.94 Lamz = 97.54 kzz = 0.80
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.10 < 1.00 (6.2.1(7))
sqrt(Sig,x,Ed*^2 + 3*Tau,z,Ed^2)/(fy/gM0) = 0.11 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,c,Rd = 0.00 < 1.00 (6.2.6.(1))
Vz,Ed/Vz,c,Rd = 0.06 < 1.00 (6.2.6.(1))
Contrôle de la stabilité globale de la barre:
Lambda,y = 20.56 < Lambda,max = 210.00 Lambda,z = 97.54 < Lambda,max = 210.00 STABLE
My,Ed,max/Mb,Rd = 0.67 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.69 < 1.00 (6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.71 < 1.00 (6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 2 PORTIQUE DE RIVE
PIECE: 3 STRUCTURE POINT: 3 COORDONNEE: x = 0.90 L = 9.05
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 37 ELU/1=17*1.35 + 18*1.50 17*1.35+18*1.50
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 600

h=60.0 cm gM0=1.00 gM1=1.00
b=22.0 cm Ay=94.30 cm2 Az=83.78 cm2 Ax=155.98 cm2
tw=1.2 cm Iy=92083.40 cm4 Iz=3387.34 cm4 Ix=166.20 cm4
tf=1.9 cm Wely=3069.45 cm3 Welz=307.94 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = -112.23 kN My,Ed = 69.24 kN*m Mz,Ed = -6.26 kN*m Vy,Ed = 1.27 kN
Nt,Rd = 3665.62 kN My,el,Rd = 721.32 kN*m Mz,el,Rd = 72.37 kN*m Vy,T,Rd = 1267.66 kN
My,c,Rd = 721.32 kN*m Mz,c,Rd = 72.37 kN*m Vz,Ed = 21.10 kN
Vz,T,Rd = 1130.13 kN
Mb,Rd = 418.33 kN*m Tt,Ed = 0.27 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = 1.00 Mcr = 570.66 kN*m Courbe,LT - c XLT = 0.57
Lcr,upp=5.02 m Lam_LT = 1.12 fi,LT = 1.15 XLT,mod = 0.58
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:

----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nt,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.21 < 1.00 (6.2.1(7))
sqrt(Sig,x,Ed^2 + 3*(Tau,y,Ed+Tau,ty,Ed)^2)/(fy/gM0) = 0.13 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.02 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.02 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.01 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
My,Ed/Mb,Rd = 0.17 < 1.00 (6.3.2.1.(1))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 3 PORIQUE COURANT
PIECE: 14 STRUCTURE POINT: 1 COORDONNEE: x = 0.00 L = 0.00
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 39 ELU/3=17*1.35 + 18*1.50 + 2*0.90 17*1.35+18*1.50+2*0.90
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 600

h=60.0 cm gM0=1.00 gM1=1.00
b=22.0 cm Ay=94.30 cm2 Az=83.78 cm2 Ax=155.98 cm2
tw=1.2 cm Iy=92083.40 cm4 Iz=3387.34 cm4 Ix=166.20 cm4
tf=1.9 cm Wely=3069.45 cm3 Welz=307.94 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 54.40 kN My,Ed = -272.85 kN*m Mz,Ed = 0.00 kN*m Vy,Ed = 0.40 kN
Nc,Rd = 3665.62 kN My,Ed,max = -272.85 kN*m Mz,Ed,max = 1.50 kN*m
Vy,T,Rd = 1278.30 kN
Nb,Rd = 3665.62 kN My,c,Rd = 721.32 kN*m Mz,c,Rd = 72.37 kN*m Vz,Ed = 89.67 kN
Vz,T,Rd = 1136.09 kN
Mb,Rd = 389.38 kN*m Tt,Ed = -0.03 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = 1.00 Mcr = 506.84 kN*m Courbe,LT - c XLT = 0.53
Lcr,low=5.02 m Lam_LT = 1.19 fi,LT = 1.23 XLT,mod = 0.54
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
kyy = 1.00 kzz = 1.00
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.39 < 1.00 (6.2.1(7))
sqrt(Sig,x,Ed^2 + 3*(Tau,y,Ed+Tau,ty,Ed)^2)/(fy/gM0) = 0.39 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.08 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
My,Ed,max/Mb,Rd = 0.70 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.74 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.74 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 4 PANNE
PIECE: 80 STRUCTURE POINT: 2 COORDONNEE: x = 0.50 L = 2.50
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 43 ELU/7=17*1.35 + 18*1.50 + 6*0.90 17*1.35+18*1.50+6*0.90
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 180

h=18.0 cm gM0=1.00 gM1=1.00
b=9.1 cm Ay=16.21 cm2 Az=11.25 cm2 Ax=23.95 cm2
tw=0.5 cm Iy=1316.96 cm4 Iz=100.85 cm4 Ix=4.90 cm4
tf=0.8 cm Wely=146.33 cm3 Welz=22.16 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 13.97 kN My,Ed = 8.79 kN*m Mz,Ed = -0.78 kN*m
Nc,Rd = 562.76 kN My,Ed,max = 8.79 kN*m Mz,Ed,max = -0.78 kN*m
Nb,Rd = 562.76 kN My,c,Rd = 34.39 kN*m Mz,c,Rd = 5.21 kN*m
Mb,Rd = 28.03 kN*m Tt,Ed = 0.00 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = -1.00 Mcr = 47.95 kN*m Courbe,LT - b XLT = 0.79
Lcr,upp=2.50 m Lam_LT = 0.85 fi,LT = 0.84 XLT,mod = 0.82
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
kyy = 1.00 kzz = 1.00
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.43 < 1.00 (6.2.1(7))
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
My,Ed,max/Mb,Rd = 0.31 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.49 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.49 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 5 LISSE DE BARDAGES
PIECE: 229 STRUCTURE POINT: 1 COORDONNEE: x = 0.38 L = 7.50
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 74 ELU/38=17*1.35 + 18*1.05 + 2*1.50 17*1.35+18*1.05+2*1.50
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 120

h=12.0 cm gM0=1.00 gM1=1.00
b=6.4 cm Ay=9.10 cm2 Az=6.31 cm2 Ax=13.21 cm2
tw=0.4 cm Iy=317.75 cm4 Iz=27.67 cm4 Ix=1.71 cm4
tf=0.6 cm Wely=52.96 cm3 Welz=8.65 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = -5.53 kN My,Ed = -2.42 kN*m Mz,Ed = 0.04 kN*m Vy,Ed = -0.07 kN
Nt,Rd = 310.44 kN My,el,Rd = 12.45 kN*m Mz,el,Rd = 2.03 kN*m Vy,T,Rd = 122.19 kN
My,c,Rd = 12.45 kN*m Mz,c,Rd = 2.03 kN*m Vz,Ed = 2.10 kN
Vz,T,Rd = 84.93 kN
Mb,Rd = 2.84 kN*m Tt,Ed = -0.01 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = -1.00 Mcr = 2.84 kN*m Courbe,LT - b XLT = 0.23
Lcr,low=10.00 m Lam_LT = 2.09 fi,LT = 2.43 XLT,mod = 0.23
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:

----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nt,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.23 < 1.00 (6.2.1(7))
sqrt(Sig,x,Ed^2 + 3*(Tau,y,Ed+Tau,ty,Ed)^2)/(fy/gM0) = 0.21 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.02 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.03 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.02 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
My,Ed/Mb,Rd = 0.85 < 1.00 (6.3.2.1.(1))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 6 potelet
PIECE: 6 STRUCTURE POINT: 1 COORDONNEE: x = 0.00 L = 0.00
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 43 ELU/7=17*1.35 + 18*1.50 + 6*0.90 17*1.35+18*1.50+6*0.90
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: IPE 220

h=22.0 cm gM0=1.00 gM1=1.00
b=11.0 cm Ay=22.89 cm2 Az=15.88 cm2 Ax=33.37 cm2
tw=0.6 cm Iy=2771.84 cm4 Iz=204.89 cm4 Ix=8.86 cm4
tf=0.9 cm Wely=251.99 cm3 Welz=37.25 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 84.64 kN My,Ed = 0.69 kN*m Mz,Ed = 0.00 kN*m Vy,Ed = 0.25 kN
Nc,Rd = 784.21 kN My,Ed,max = 9.42 kN*m Mz,Ed,max = -1.55 kN*m Vy,T,Rd = 310.17 kN
Nb,Rd = 170.99 kN My,c,Rd = 59.22 kN*m Mz,c,Rd = 8.75 kN*m Vz,Ed = -1.30 kN
Vz,T,Rd = 215.28 kN
Mb,Rd = 43.04 kN*m Tt,Ed = -0.00 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
z = 1.00 Mcr = 51.35 kN*m Courbe,LT - b XLT = 0.65
Lcr,upp=6.50 m Lam_LT = 1.07 fi,LT = 1.05 XLT,mod = 0.73
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 6.50 m Lam_y = 0.53 Lz = 6.50 m Lam_z = 1.96
Lcr,y = 4.55 m Xy = 0.91 Lcr,z = 4.55 m Xz = 0.22
Lamy = 49.92 kzy = 0.69 Lamz = 183.63 kzz = 0.81
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.12 < 1.00 (6.2.1(7))
sqrt(Sig,x,Ed^2 + 3*(Tau,y,Ed+Tau,ty,Ed)^2)/(fy/gM0) = 0.12 < 1.00 (6.2.1.(5))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.01 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
Lambda,y = 49.92 < Lambda,max = 210.00 Lambda,z = 183.63 < Lambda,max = 210.00 STABLE
My,Ed,max/Mb,Rd = 0.22 < 1.00 (6.3.2.1.(1))
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.57 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.79 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!
 CALCUL DES STRUCTURES ACIER
----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/AC:2009, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des familles
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE: 7 contreventement
PIECE: 204 STRUCTURE POINT: 3 COORDONNEE: x = 1.00 L = 7.09
m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 39 ELU/3=17*1.35 + 18*1.50 + 2*0.90 17*1.35+18*1.50+2*0.90
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
ACIER fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: CORNIER CAE50X5

h=15.0 cm gM0=1.00 gM1=1.00
b=15.0 cm Ay=15.00 cm2 Az=15.00 cm2 Ax=29.27 cm2
tw=1.0 cm Iy=624.00 cm4 Iz=624.00 cm4 Ix=9.67 cm4
tf=1.0 cm Wely=56.88 cm3 Welz=56.88 cm3
Weff,y=56.88 cm3 Weff,z=56.88 cm3 Aeff=29.27 cm2

----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 65.06 kN My,Ed = -8.56 kN*m Mz,Ed = -0.27 kN*m Vy,Ed = 0.06 kN
Nc,Rd = 687.96 kN My,Ed,max = -8.56 kN*m Mz,Ed,max = -0.27 kN*m Vy,T,Rd = 203.02 kN
Nb,Rd = 291.06 kN My,c,Rd = 13.37 kN*m Mz,c,Rd = 13.37 kN*m Vz,Ed = -5.24 kN
Vz,T,Rd = 203.02 kN
Tt,Ed = -0.01 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 7.09 m Lam_y = 1.31 Lz = 7.09 m Lam_z = 1.31
Lcr,y = 5.67 m Xy = 0.42 Lcr,z = 5.67 m Xz = 0.42
Lamy = 122.83 kyy = 0.88 Lamz = 122.83 kzz = 0.69
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd + My,Ed/My,c,Rd + Mz,Ed/Mz,c,Rd = 0.55 < 1.00 (6.2.1(7))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.03 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
Lambda,y = 122.83 < Lambda,max = 210.00 Lambda,z = 122.83 < Lambda,max = 210.00 STABLE
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.44 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.44 < 1.00
(6.3.3.(4))
----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!