Computerized Embroidery Machine - Best Embroidery Machines (PDFDrive)

Version：2008-06
Computerized
Embroidery Machine
B E C S-C18
Owner's Manual
Dahao brand industry sewing machine computerized
control system was awarded the title of China Top
Brand by Chinese General Administration of Quality
Supervision, Inspection and Quarantine in September
2007.
Certificate No. 06-018-03-094
CERTIFICATE OF CONFORMITY OF
QUALITY MANAGEMENT SYSTEM

CERTIFICATION
This is to certify that the quality system of
Beijing Xingdahao Technology Co., Ltd.
Is in conformity with
GB/T 19001-2000 idt ISO 9001:2000 Standard
This certificate is valid to the following product(s)/service:

Design and manufacture of computerized sewing
Equipment control system
Registration No.:0203Q15748R2M
ACCREDITED BY MEMBER OF
THE IAF MIA FOR QMS
Index
Index
Chapter 1 General Descriptions .....................................................................................................1
1-1 Warnings and Cautions .....................................................................................................1
1-2 Main Features....................................................................................................................3
1-3 Technical Specifications ...................................................................................................8
Chapter 2 Operation Instruction .....................................................................................................9
2-1 Configuration and Direction of the Control Panel ............................................................9
2-2 Instruction of Control Panel............................................................................................10
2-3 Instruction of the Main Screen........................................................................................11
2-4 Notes on Menu State .......................................................................................................17
2-5 How to Input Numerals, Letters and Symbols................................................................18
2-6 Moving of the cursor.......................................................................................................18
2-7 Flow Chart of Embroidery ..............................................................................................18
2-8 Normal Embroidery, Returning and Patching.................................................................25
2-9 Relations between Normal Embroidery, Idling and Position Idling...............................26
2-10 Operation Bar and Turn Shaft Button ...........................................................................27
2-11 Darning Switch .............................................................................................................28
2-12 System's Working States...............................................................................................28
Chapter 3 Disk Management........................................................................................................30
3-1 Disk Choosing.................................................................................................................30
3-2 Design Preview ...............................................................................................................33
3-3 Select One or Several Designs ........................................................................................34
3-4 Design import..................................................................................................................35
3-5 Design Export .................................................................................................................37
3-6 Folder Operation .............................................................................................................38
3-7 Deleting Objects in Disk (Including Design Files and Folders) .....................................39
3-8 Formatting a Disk............................................................................................................39
Chapter 4 Memory Design Management .....................................................................................41
4-1 Memory Design Management Screen and Other Memory Design Operation Screens ..41
4-2 Select One or Several Designs ........................................................................................44
4-3 Selecting a Design for Embroidery.................................................................................45
4-4 Design View....................................................................................................................45
4-5 Copy the memory design ................................................................................................47
4-6 Deleting the memory design ...........................................................................................48
4-7 Design add applique........................................................................................................49
4-8 Satin stitch compensate...................................................................................................52
4-9 Edit packed design ..........................................................................................................53
4-10 Design divide ................................................................................................................55
4-11 Combine the designs .....................................................................................................56
4-12 “High speed design”......................................................................................................57
4-13 Create design from packed............................................................................................58
4-14 Design from parameter..................................................................................................58
4-15 Frame and Make Design ...............................................................................................59
4-16 Create outline from design............................................................................................60
BECS-C18 computerized embroidery machine owner’s manual I

Index
4-17 Copy design with varied switch length......................................................................... 61

4-18 Setting design parameters ............................................................................................. 61
4-19 Design come from PC................................................................................................... 63
Chapter 5 Managing of Parameters.............................................................................................. 64
5-1 Normal Parameters ......................................................................................................... 65
5.1.1 Design directions ...............................................................................................................65
5.1.2 Setting of rotate..................................................................................................................65
5.1.3 Setting of X-scale ..............................................................................................................66
5.1.4 “Rep. Prior” .......................................................................................................................67
5.1.5 “Rep. Mode” ......................................................................................................................68
5.1.6 “X&Y Reps” ......................................................................................................................68
5.1.7 “X&Y Interval”..................................................................................................................68
5.1.8 “Prior Mode” .....................................................................................................................68
5-2 Setting of other embroidery parameters ......................................................................... 69
5.2.1 Setting Procedure for Other Parameters.................................................................. 70
5.2.2 Introduction of Some Functions of General Parameters......................................... 71
5-3 Set User-defined parameter ............................................................................................ 74
5-4 Purview of Machine Parameter Manage......................................................................... 76
5.4.1 Unlock/Change the administrator password ......................................................................77
5.4.2 Machine Administrator cancels machine lock ...................................................................78
5.4.3 Administrator reset (or save) optimize parameter..............................................................79
5.4.4 Change the factory password .............................................................................................79
5.4.5 Unlock the factory password .............................................................................................80
5.4.6 Factory Save/Reset Parameters..........................................................................................80
5-5 Initialize Parameters ....................................................................................................... 80
5-6 Save all parameter to disk............................................................................................... 81
5-7 Read all parameter from disk.......................................................................................... 81
5-8 Adjust Parameters of X＆Y Servo Drivers .................................................................... 81
5.8.1 Set the parameter ...............................................................................................................82
5.8.2 To inquire servo driver status.............................................................................................82
5.8.3 Write driver parameters .....................................................................................................83
5.8.4 Restore default driver parameters ......................................................................................83
Chapter 6 Assistant Operation ..................................................................................................... 84
6-1 Assistant embroidery operation ...................................................................................... 84
6.1.1 Resume Design Start..........................................................................................................84
6.1.2 Save design start ................................................................................................................85
6.1.3 Auto to start position..........................................................................................................85
6.1.4 Stitch stop down.................................................................................................................86
6.1.5 Setting another start ...........................................................................................................87
6.1.6 Set B Point .........................................................................................................................88
6.1.7 Operation on AFC, Sequin and Coiling Devices ...............................................................90
6.1.8 Upper thread hold operation .............................................................................................. 90
6-2 Other assistant operation................................................................................................. 90
6.2.1 View Embroidery Parameter..............................................................................................91
6.2.2 View Statistics Information................................................................................................92
II BECS- C18 computerized embroidery machine owner’s manual

Index
6.2.3 Power resume setting/ frame start setting.......................................................................... 93

6.2.4 Power resume .................................................................................................................... 94
6.2.5 Set embroidery scope in software...................................................................................... 95
6.2.6 Set system clock ................................................................................................................ 96
6.2.7 Language Choice............................................................................................................... 97
6.2.8 Machine Soft Information ................................................................................................. 97
6.2.9 Help ................................................................................................................................... 98
6.2.10 Machine Test ..................................................................................................................... 98
Chapter 7 Other Operation .........................................................................................................101
7-1 Operation on color-changing order ...............................................................................101
7.1.1 Input Color Line .............................................................................................................. 101
7.1.2 Modify color line............................................................................................................. 102
7.1.3 Replace a needle.............................................................................................................. 103
7.1.4 Set color of showing design ............................................................................................ 103
7-2 Design border operation................................................................................................104
7.2.1 Check the boundary of a design ...................................................................................... 104
7.2.2 Move the frame along the boundary of a design ............................................................. 105
7.2.3 Create design from outline .............................................................................................. 106
7.2.4 Frame to generate design, then embroider back .............................................................. 106
7.2.5 Embroider a “+” in current position ................................................................................ 107
7.2.6 Frame and embroider back for one line........................................................................... 108
7.2.7 Embroider the boundary of current design ...................................................................... 109
7.2.8 Embroidery true boundary of current design................................................................... 110
7-3 Positioning Idling..........................................................................................................110
7.3.1 Go ahead stitches..............................................................................................................111
7.3.2 Go back stitches .............................................................................................................. 112
7.3.3 Next Color Code.............................................................................................................. 112
7-4 Reset X/Y Displacements .............................................................................................112
Chapter 8 Memory Design Edit..................................................................................................114
8-1 Start Editing Design ......................................................................................................114
8-2 Design Edits Operation .................................................................................................115
8.2.1 Summarize....................................................................................................................... 115
8.2.2 Document and View Operation ....................................................................................... 116
8.2.3 Key for Positioning Stitch and Editing Stitch.................................................................. 116
Chapter 9 Letter Design .............................................................................................................118
9-1 Enter Letter Design Operation ......................................................................................118
9-2 Enter Char String and Basic Parameter.........................................................................118
9-3 Character Pattern Save ..................................................................................................124
Chapter 10 D type sequin embroidery........................................................................................126
10-1 Brief introduction on sequin embroidery ....................................................................126
10-2 Embroider sequin ........................................................................................................127
10-3 Input sequin design .....................................................................................................128
10-4 Sequin design edit .......................................................................................................129
10-5 Parameter setting about multi-sequin embroidery ......................................................132
10-6 Change color order and set sequin mode ....................................................................135
BECS-C18 computerized embroidery machine owner’s manual III

Index
10-7 Manual operation of sequin embroidery..................................................................... 140

10-8 Debugging multi-sequin embroidery.......................................................................... 141
10-9 Sequin mending .......................................................................................................... 142
Chapter 11 J Type Sequin Embroidery ...................................................................................... 143
11-1 Brief Introduction on J Type Sequin Embroidery ...................................................... 143
11-2 Operating Sequin Embroidery .................................................................................... 144
11-3 Color changing............................................................................................................ 144
11.3.1 Setting sequin mode:........................................................................................................ 144
11.3.2 Sequin color changing setting.......................................................................................... 147
11-4 Parameter instruction .................................................................................................. 149
11-5 Manual operation of sequin embroidery..................................................................... 150
11-6 Sequin testing.............................................................................................................. 151
11-7 Sequin mending .......................................................................................................... 151
Chapter 12 Directions on Coiling, Taping and Zigzag Embroidery .......................................... 153
12-1 Function Introductions................................................................................................ 153
12-2 Main Technical Details............................................................................................... 154
12-3 Parameters and parameter setting ............................................................................... 154
12-4 Relative Operations of Special Embroidery ............................................................... 157
12.4.1 Shift between Lock Stitch Head and Special Head............................................................... 157
12.4.2 M Axis Operation of Taping Embroidery ............................................................................. 159
12.4.3 Operations of Clamp Foot..................................................................................................... 160
12-5 On Debugging Special Embroidery............................................................................ 160
12-6 Steps on Special Embroidery...................................................................................... 161
12-7 Mechanical Category and Driving Mode Choice of Special Embroidery Machines . 161
12-8 Definition Charts of DIP Switches of E874 Boards ................................................... 165
Appendix Ⅰ Parameter Setting List ...................................................................................... 167
Appendix Ⅱ Directions on USB operations.......................................................................... 180
Appendix Ⅲ Error Information ............................................................................................. 181
Appendix Ⅳ Making of Special Multi-Sequin Design.......................................................... 184
Appendix Ⅴ Network Connection of Embroidery Machines................................................ 193
IV BECS- C18 computerized embroidery machine owner’s manual

Chapter 1 General Descriptions
Thanks for using the Computerized Embroidery Control System of DAHAO
Company. It is appreciated that you do read this manual carefully in order to
operate the machine correctly and effectively. Besides, you should keep this
manual for future use.
1-1 Warnings and Cautions
Notice
During the operation, do not try to open the machine box. The high voltage
Danger contained in some parts can be deadliness. Rotating parts may cause serious
injury.
Forbidding Don't expose the machine to humidity gas, poisonous gas, water, and dust.
Don’t restore or operate in vibration, which may cause trouble to the

Forbidding
machine.
Notice Please abide all the warnings and safety requirements to save life.
LCD belongs to fragile goods. Do not use hard materials to click on the
Notice
screen.
Before plugging in, please make sure if the lamp of floppy disk driver is on,
Notice
don't move out the floppy disk..
We will add appendix if necessary, if there is any difference between the
Notice
manual and appendix, subject to the appendix.
In Transportation
Notice Don't hold the cable when moving..
Notice Please abide all the warnings and safety requirements to save life.
Overloading may cause serious loss. Please load according to the

Force
instruction on the box..
Installation
BECS-C18 computerized embroidery machine owner’s manual 1

Don't jam the vent on the device. Don’t plug up the machine, or it may set
Notice
fire.
Notice Make sure the installation direction is correct..
Notice Don't expose the machine to humidity gas, poisonous gas, water, and dust.
Cable Connection
Forbidding Don't test the insulation of the circuit loop.
Forbidding Never try to connect overloaded electronic device on the connector..
Notice Make sure the insulating of the cable is fine.
Notice Communicating cable and power cable should be separated.
All the cables should be well fixed. Don’t put any strength on cables. Make
Notice sure the turning point of cable is well protected. Add pipes to increase
insulating capability.
Machine should be grounded. The resistance should be no larger than 10
Notice
Ω.
Operation direction
Danger Don't operating the machine when there is any damage on the surface..
Forbidding When machine is running, do not touch any running part.
Make sure the configuration of power supply in normal. Use stabilized

Notice
voltage power supply when the voltage rebound is between -10%~10%.
In case of warning, please check out the problem. Operation can only be
Notice
carried out again when problem is solved.
The power supply has over-currency protection function. There is a 3 mins
Notice
time lag before the function can be used again.
Maintenance
If you need to open the machine cover, cut out the power supply first. Duo
Warning to the capacitance after power off, operator must wait one minute till he can
open the machine cover.
Circuit boards can be damaged by static. Non-professional technician can
Notice
not disassemble circuit boards.
2 BECS- C18 computerized embroidery machine owner’s manual

If machine is inactive for a while, users must power on the machine

Notice
regularly (once in 2 or 3 days, more than an hour for each time).
If machine is inactive for a long time, users should have the machine
Notice
checked before power on.
Rejection
Rejection should abey the rules and regulations set by national indudstrial
Notice
electronic standards.
1-2 Main Features
1. LCD display
It offers delightful operation and easy learning. The beautiful screen display turns
everyday work into joyful experiences.
2. Shutdown of LCD Display
Following measures were taken in order to extend the LCD life: LCD will turn off
automatically in case of no operation in 10 minutes (the time can be changed in
parameter setting). A touch of the screen or the task-shifting key will reboot the
LCD.
3. Super-Large Memory Capacity
The memory capacity reaches 16 million stitches, in which 400 designs can be
restored. Its super-large memory capacity can meet demands of different
customers.
4. Maximum One Million Stitches for 1 Design
At present a single design in the system has the maximum of 100,000,000 stitches
and 250 times of automatic color changing.
5. Multi-Task Parallel and Free Shift among Tasks

During embroidering, actions like design input & output, preparation for the
following designs and modification of parameters can be carried out. Flexible
shift among tasks can be realized by using the task-shifting key.
6. Storage of Frequently Used Parameters and Color-Changing Order for Each
Design
Design will be saved along with its parameters, color-changing orders and needle
bar colors. System can memorize the operational details for each design. Users
can set parameters for a design during the embroidery process of the previous
design, which will help saving time and improving efficiency. More importantly,
it is one basis to realize network management.
7. Group Management of Parameters
Parameters can be divided into groups based on their functions. The last two
groups of parameters can be restored, recovered and password-protected.
8. Input & Output Using USB
Except for DOS, FDR and ZSK format, customers can use USB disk for data
transfer. USB disk supports DIR operation, which is easy for design management.
For each directory, system supports operation on 400 designs or sub-directory.
There is no limitation between directory levels. Design formats like DSB, DST,
ZSK and FDR can be loaded.
9. Input of Several Design Files at One Time
Both floppy and USB disks support multi-design input under one directory.
10. Input design through network, color-changing order, etc.

Network connector is available, which help user input design, color-changing
order, patch sewing, etc.
11. Network Function
A surveillance LAN can be built by using the connectors and linked to the factory
LAN, which realizes network management, improve production efficiency and
reduce possible mistakes. It’s the best choice of embroidery equipment for
enterprises to take the modern enterprise management. The explanation is
appendix Ⅴ.
12. Patch Embroidery
This function can set a patch code after the color code or stop code, and when the
machine embroiders the patch code, it will halt and move frame out for patching.
After stick a patch, user would pull the operation bar to let the frame move back
and continue embroidering.
13. Break Adjusting
For various machines, this function can make the machines stop correctly, which
means that the main shaft stops at 100 degree.
14. Starting Point Saving
This function can save and store the start embroidering point of each design,
instead of repeating moving frame manually to find the design origin when
selecting the same design.
15. Mechanical Maintaining and Testing
This function is to easily judge the malfunctions when maintaining and testing,

which consists of computer testing, encoder testing, main shaft speed testing,
machine parts testing and the main shaft stopping at any position, etc.
16. Multi-Language Support
Currently, The system supports Chinese / English /Espanol/Turkish language.
17. Design Output
Design can be output and saved into floppy disk or USB disk. Adoption of
TAJIMA’s binary system enjoys the advantage of data transmitting through the
World Wide Web (other formats may not be transmitted directly).
18. Repetition Embroidery
The machine can increase embroidery productivity by repetition embroidery,
which can also be used with cyclic embroidery.
19. Cyclic Embroidery
The machine also can increase embroidery productivity by using cyclic
embroidery function, by which the machine automatically returns to the origin
point and starts the same embroidery design again when finishing the design one
time.
20. Design Compiling
(1) Compiling the Data of Selected Design to Generate New Design
Users can compile any design according to zoom ratio, rotate angle, normal
repetition or partial repetition to generate a new design and save it in the memory
card. The newly generated design can be used for embroidering, output or other
operations.

(2) Compiling the Combined Design
System can compile the pre-set combined design to generate a new one and save
it to the memory card. The newly generated design can be used for embroidering,
output or other operations.
21. Letter Design
There are altogether 28 letter-bases. Users can make groups and change the letter
order according to different tasks. This operation is simple and easy managing.
22. Design Editing
By using this function, users may insert, modify or delete certain stitch at the
selected point. New designs can be created by this function too.
23. Speed Adjusting
The highest speed for embroidering can be set. During the process of
embroidering, speed changes automatically as long as the needle interval changes.
24. Thread Trimming
Thread trimming can be manually controlled. Trimming acts automatically at the
end of embroidery process or color changing.
25. Thread Break Detect
In case of thread break or running out of bottom thread, machine stops and
warning lights start to blink.
26. Color Changing
At the color changing point, user can either act color changing manually or let the
system do according to the preset order automatically.

27. Special Embroidery
BECS-C18 computerized embroidery owns special embroidery functions (coiling,
taping and Zigzag embroidery).
1-3 Technical Specifications
1. Maximum design saving quantity: 400 designs
2. Memory capability: 16 million stitches
3. Screen resolution: 640*480
4. Network transfer speed: 10Mbps
5. Data transfer mode supported: floppy disk, USB disk and network
6. Stepping Precision: minimum stepping precision is 0.1mm
7. Stitch range：from 0.1mm to 12.7mm

Chapter 2 Operation Instruction
2-1 Configuration and Direction of the Control Panel
A. Configuration of the Control Panel

1
2
1
4
4 3
2
1. LCD Screen
C18 adopts high-luminance LCD display.
2. Main USB Interface
USB disk can be plugged in for data input/output. The external floppy driver is
also connected by USB interface.
3. Serial Port to Link PC
Its serial port can be connected with PC for design transmission.
4. Network Interface
C18 has two key functions: network supervision and design data transfer.
Network interface is used for network communications..
B. Direction in Using the Floppy Disk
This external floppy driver uses USB interface. Make sure the plug-in direction is

correct. Try to avoid using force with incorrect plug-in direction, or it may destroy
the floppy driver and disk.
C. Direction in Using the USB Disk
Please pay close attention to electrostatic phenomenon. Don’t forget to discharge
before plugging in/out the USB disk.
USB disk features plug-in direction. Users should avoid plugging out during
writing or loading data, because it may result in loss of data. We highly
recommend users to check the data integrality in case of data missing.
Note: During the process of USB format, sudden loss of electricity or plugging
out the disk may break down the USB.
D. Direction of Network Connection
Preset the network parameters before the connecting. Otherwise other machines in
the network maybe can’t communicate.
2-2 Instruction of Control Panel
The key on the keyboard cooperate with LCD. If you want to operate function in
any menu on the LCD, just push relative shortcut key on the keyboard. The state
of that key will be shown on the screen.

1 3
1 2
2
3
4 4
7
5
6 5
7 6
10 9 8 10 9
Number Name Description

1 LCD Displays every operation.
2 +/- shift To show plus & minus of inputted number.
3 Task Shift If the user opens several screens, he can shift among the
screens by this key.
4 Digital key It is used for selecting menu or setting parameter.
5 Manual Frame In operation the direction of frame-moving is the same as the

Moving direction key. The combination of directions is supported,
namely pressing the nearby 2 direction keys will move the
frame in the 45 degree between the two directions.
6 Speed Shift of Press this key to switch the frame-moving speed between
Manual
Frame-moving
(high speed) and (low speed).
7 Speed adjust
Push the button or to reduce or increase the
embroidering speed.
8 Confirm To confirm certain operations.
9 Exit To exit certain operations.
10 Function select Push the function keys within this area to select function
menus.(Note: If you press the keyboard in the main screen
area twice ,it means correspond to enter and to exit. )
2-3 Instruction of the Main Screen
Note: Press the button can shift between the following two pages.

No. Display Name Description

1 Real time Embroidery stitch forms or design previews are
tracking displayed in this area.
2 Design Related design information is displayed in this
information area.
3 Main shaft speed The set and actual speed can be viewed in this


area.
4 Current stitch The current stitch form information is displayed
form information here.
Frame moving speed （ use to shift
between low speed and high speed ）
Main shaft state （ running 、 stop in
position 、not stop in position ）
Embroidery state （ thread break 、

Machine state
information finish 、color changing 、jump 、
（follow the pull bar to stop ）

5
order of left to
Cyclic embroidery , none cyclic embroidery
right, top to
Assistant embroidery statelockstitch/special
bottom）
embroidery（lockstitch , sequin , etc.）
Off-set point
Assistant embroidery mode
Network state （ disconnected 、
connected 、successful register ）

6 Color changing
and current stitch
position
7 Next group of Press this button to shift among different
function key function groups
8 Assistant Design origin, needle stops down, offset point,
embroidery sequin, special embroidery, etc.


operation
9
Main shaft stops to 100° , press this key;
Set color after that, system goes to the color-changing
changing order order menu, press relative number to act
color-changing.
10 After stopping, press this key to select to trim
trimming
upper or lower thread.
11
Turn the main If the main shaft doesn’t stop at 100° ;
shaft at 100° Press the key and then the main shaft will
manually
arrive to this position .
12 When the machine stops, press the key
“Manual Frame-moving” to move the frame
Go to stop point (e.g. in case of patching). Then press this key
and the frame will automatically return to the
stop point of the current design.
13 When the machine stops, press it, the frame
Go to start point will automatically return to the start point of the
current design.
14 Machine Press this key to enter into machine parameter
parameter setting and operations.
management
15 Disk Press this key to enter disk management,
management including operations of floppy disk and USB.
16 Press this key to enter into design manage
Design
window, including embroider design, input
management
design to memory, show design, generate
design, etc.


17 Special Press this key to enter into manual shifting
embroidery special embroidery window.
mode
18 Other assistant Press this key to enter other assistant
management management like clock setting and help.
19 Positioning In embroidery confirmation status, press this
idling key to do the operations of positioning idling.
20 Design border Press this key to enter design border operation
operation window
21 Change design Press this key to shift the design direction
direction among 8 directions.
In this state, press related needle position key to
select a position. Pull bar to start embroidering.
Manual When meet color-changing code, machine stops
22 color-changing automatically, appears. Then you should

manual start act manual color-changing. Type in the position
you need, pull bar to start embroidering
（manual start）.


If you set machine to auto-color-changing, you
should first set needle color-changing order
（press the key in the main screen）.
During embroidery, no matter where the current

Auto
needle locates, system will act color-changing
color-changing
according to this order. When you meet
manual start
color-changing code, machine will stop
automatically and change to the needle position
that already set. If you set auto start, machine
will start automatically; if you set to manual
start, pull bar to start.
Auto
color-changing
auto start
23 System is now in normal embroidery state.
When you pull bar, the main shaft rotates,
Normal frame moves along the design trace. Pull bar to
embroidery go back, machine idling back in low speed.

When machine stops, press this key to shift to
low speed idling .

System is now in high speed idling state. Pull
bar but main shaft doesn’t move, frame moves
High speed along the design trace. Pull bar to go back,
idling main shaft doesn’t move, frame moves along

the design trace. When machine stops, press the
key to shift to high speed idling 。


System is now in high speed idling state. Pull
bar but main shaft and frame don’t move, stitch
increasing; pull bar to stop, the frame goes to
the real position of the current stitch. Pull bar to
High speed
back, main shaft and frame don’t move. Stitch
idling
decreasing. Pull bar to stop, the frame goes
back to the real position of current stitch. When
machine stops, press this key to change to
preparing state .
24 Embroidery preparing state, you can select
design, set parameter, etc. this key to confirm to
Embroidery
preparing state change machine state from preparing state
to confirm state .
Embroidery confirm state, you can pull bar to
embroider. When machine stops, press this
Embroidery
confirm state key to confirm to release confirm state
and back to preparing state .
2-4 Notes on Menu State
If one menu is labeled the mark “ ” or “ ”, this indicate that this menu can
not be accessed and modified. While if one menu is labeled “ ” or “ ”, it
indicates that this menu can be accessed and modified. If there is a “ ”, then this
parameter can be modified only if the relieving the password first.

2-5 How to Input Numerals, Letters and Symbols
For some menu, press the key “ ” to enter into setting (optional), press “ ”
to shift options, press “ ” to confirm.
To type in number, you can press “ ” to enter radix point, press “ ” to enter
negative number. When there are several digits or letters on one key, you can
press the key until you get the number or letter you want. For example, press
trice, then you can get “I”. “ ” is used for shifting capital letters and
small letters. “ ” is used for deleting the last letter you typed in.
2-6 Moving of the cursor
The cursor of this computer is displayed as “ ”. You can press “ ”
or relative digit number to move the cursor to the option. Press “ ” or “ ” for a
while, the cursor will move consecutively among each option.
2-7 Flow Chart of Embroidery
The machine embroiders based on the designs in its memory. The following is the
basic Flow Chart of Embroidery.

1. Inputting Designs
Inputting Designs Inputting
2. Choosing a Design
3. Assistant Operations
4. Embroidery Confirmation
5. Pull the Bar to Embroidery
6. Cancel Embroider 7. Manual Operation
A. Import Designs
The user can import designs through network, floppy disk or USB disk. Only with
state it’s possible to transmit designs by network. For USB operation (disk
operation), click in the main screen to enter into the “disk management”
screen. You can also input designs by using “ ” in the design management
screen.
B. Choosing a Design
If the design management screen is not opened, click in the main screen to

enter it. If the screen is opened but the current window stays at another function
screen, press the blue task switch key on the panel to enter the design
management screen. Only in the status of “ ” it is allowed to choose design for
embroidery.
a. After enter into design management, press “ ” to select a design,
then press “ ” or “ ”.
b. If the design’s start point has been saved, the prompt “Move frame to start
point” will appear when entering the main screen. Click and the frame
will automatically return to the start point.
C. Assistant Operation
After choosing the design, the user will enter the main screen, and he can do the
needed assistant operations before embroidery.
a. Set repeat, rotate and magnify——click “ ” then “ ” to enter the

parameters management screen

b. Set applique embroidery——click “ ” to enter the design management
screen and click “ ” to set applique according to prompts.

c. Show the range of embroidery design, move frame along the boundary design,
embroider along the design range, embroider one cross, embroider one line,
embroider the design outline——press “ ” to enter the assistant operation

screen
d. Auto to start position——press “ ” to enter into assistant embroidery

operation menu. Please note that this function is to locate the design in the center
of the frame area as preset in soft limit. If you want set soft limit area, press
“ ” to enter into assistant management menu.
e. Save design start——click “ ” to enter the assistant operation screen.

Note: The origin point has to be set before saving the start point. If you want to
set the origin point, click “ ” and enter the “assistant management Operations”.
f. Set cyclic embroidery——click “ ” to enter the parameter management
screen. Move cursor to “Embroidery assistant parameter” and press . Then

select Sewing Para1 B02 and set according to prompts.
D. Embroidery Confirmation
1） The user can click after finishing assistant operations. Press in
the followed prompt and (embroidery preparation) will change into

(embroidery confirmation), which means that the machine has entered the
embroidery confirmation status.
If “ ” is chosen, the machine will remain in the preparation status. Pull the

bar and the machine will not run and a prompt will appear to ask the user to
confirm embroidery.
2） Setting another start
After embroidery confirmation, if needed, click “ ” to set another start

according to the prompts. Note: It’s of no effect to set another start after starting
embroidery.
3） Setting the Way for Color-Changing and Starting
In the main screen, click “ ” (or “ ”, “ ”), the state will switch among
(auto color-change, auto start), (auto color-change, manual start) and
(manual color-change, manual start).

4） Setting Normal Embroidery and Idling
Click “ ” (or , ) in the main picture and the state will switch among
(normal embroidery), (low-speed idling) and (high-speed

idling).
E. Pull the Bar to Embroider
Operation bar embroidery bar is installed under the table
1） Stop Status:
Pull the bar right to begin embroidery (including low and high speed idling)
Pull the bar left to return (including low and high speed idling)
2） Running status:
Pull the bar right to the end to embroider slowly and release to normal speed.
Pull the bar left to stop embroidery (including low and high speed idling).

F. Manual Operation
1） Manual Trimming
When the machine stops, click in the main screen. Follow the prompt and
select a trimming mode (“trim top & bot.” or “trim bottom”). Then click to
trim, or click “ ” to exit trimming operation.
2） Manual Frame-Moving
When the machine stops, press the keys （“ ”

） to move the frame in
the corresponding direction. Press the next two keys at the same time to move the
frame in the direction of the angle bisector. “ ”is the speed key for manual
frame-moving. Press “ ”to switch between (high speed) and (low

speed).
3） Clearing the Frame Coordinates
When the machine stops, click “ ” then click “ ” to clear the XY

displacements displayed in the main screen. The function can be used with
manual frame-moving.
4） Manual Color-Changing
When the machine stops, you may type in needle position number in the main
screen to enter the manual color-changing screen. Then press the needle number
for color-changing, and the machine head will automatically move to the
corresponding needle position.
5） Turn the Main Shaft to 100°Manually
Usually the main shaft is needed to stop at 100°when needle/color-changing,

frame-moving and beginning embroidery. The user can manually turn the main
shaft at 100° when it hasn’t reached there. Click “ ” in the main screen and
then choose “ ” in the followed prompt to carry out the function.
After the operation, the icon (main shaft not in the right position) will be
replaced by (main shaft in the right position).

6） Go to Start Point
In the main screen click and choose in the followed prompt. Then the
frame will return to the start point.
7） Go to Stop Point
Click in the main screen and choose in the followed prompt. Then
the frame will return to the stop point.
8） Positioning Idling
Use this function after embroidery confirmation. Positioning idling enables the
machine to move to the designated position without embroidering according to
the user’s requests. Click in the main screen then the user can set the
positioning idling of needle number, color-changing code and stop code.
9） Let Needle Down (The Needle Stops at the Designated Low Position)
This function is intended for quilt embroidering. Click in the main screen
and then the option “Let needles down”. When clicking , the needle will prick
into the embroidery cloth and a prompt will appear. After releasing the cloth
(cloth has to be separated from the frame), move the frame to the designated
position and click . After this operation, the needle is still down. When the

cloth is placed on the frame again, click to turn the main shaft to 100º
manually.
10） Manual Operations of Automatic Frame Changer (AFC), Sequin and
Special Embroidery
The machines are equipped with devices for AFC, sequin and special embroidery.
For such machines, click and then select this option to enter the concerned
menu. Click the corresponding keys according to the prompts.
G. Embroidery Release
When the machine stops, click . Choose in the followed prompt and
(embroidery confirmation) will change into (embroidery release).

2-8 Normal Embroidery, Returning and Patching
In embroidery confirmation status (the icon appears), push the patching

switch of machine head (that will perform normal embroidery) to the normal
embroidering mode, and push the patching switch of machine head that will not
embroider to the patching mode, and then pull the operation bar to right and
release it to let the machine start normal embroidery. (When you pull the bar right
and don't release it, the machine will embroider in lower speed.) During
embroidering, pull the bar left, the machine will stop.
After the machine stops, pull the operation bar to left and the frame will return to
its last position along original path. Pull the bar one time, the frame return one
needle step. Pull the bar continuously and the frame will return one needle step
after another continuously. After the frame returns 10 needle steps continuously,

the frame can return continuously even when you release the bar. (This may be
different for different machine types). When the frame return continuously,
release the bar and pull it left again, the frame will stop returning.
The aim of returning is usually to perform patching embroidery. After the
returning stops, push the patching switch of machine head that will perform
patching embroidery to go to the patching mode, and then pull the operation bar
to right and the machine head will start patching embroidery while other heads
don't. When the frame goes to the point where the frame begins to return, other
heads whose patching switches are in normal embroidering mode will start to
embroider.
2-9 Relations between Normal Embroidery, Idling and Position Idling
Functions as idling, returning, etc. are intended for the convenience of darning.
Low-speed idling, high-speed idling or positioning idling can be used as needed
in embroidery. In the status of idling, the returning can be low-speed idling
returning, high-speed idling returning or positioning idling returning.
In the main screen, you may press “ ”, (“ ” or “ ”) to switch among
“ ” (normal embroidery), “ ” (low speed idling) and “ ” (high speed
idling).
After setting low-speed idling , the main shaft remains inactive when pulling
bar for normal embroidery, but the frame runs forward along the stitch trace.
When pulling bar for returning, the main shaft keeps inactive, but the frame
returns along the stitch trace.

After setting high-speed idling , the main shaft and frame remain inactive, the
count increases based on a unit of 100 stitches. After pulling the bar for halting,
the frame moves directly to the actual position of the current count. When
pulling bar for returning, the main shaft and frame keep inactive, but the count
decreases. After pulling the bar for halting, the frame returns directly to the actual
position of the current count.
The positioning idling can move the frame directly forwards (or backwards) to a
designated position, or to a latest color-change position, or even to a latest
stop-code position. In the main screen press and the user can select
forward/backward positioning idling by stitches, color change code or stop code.
After the system returns to the main screen, pull the bar forward/backward to
complete the positioning idling.
2-10 Operation Bar and Turn Shaft Button
1. Operation Bar (Embroidery Bar under the Table)
Stop status: pull the bar right to begin embroidery (including idle running in high
or low speed) and pull the bar left to return (including idle running in high or low
speed)
Running status: pull the bar right to the end to embroider slowly and release to
normal speed and pull the bar left to stop embroidery.
2. Turn Shaft Button (over the operation bar case, on the right under the table)
Press the button to make the main shaft rotate one cycle and stop at 100±2.5°.

2-11 Darning Switch
The darning switch can be divided into “3-place” and “2-place”.
1. Thread Break Detecting Device of 3-Place
There is a switch on every head of machine. When the switch is up, this head is in
normal embroidering mode and when it is in the middle, this head is in patching
mode and when it is down this head is in stop mode.
2. Thread Break Detecting Device of 2-Place
On every head of the machine, there is a patching switch, and it can be move with
hand to the up, middle or down position, but it is stop only at the middle or down
position. When the switch is pushed to up position, it cannot stay at up position,
and the lamp is red, which hints that this head is in patching mode. In addition,
while thread breaking during embroidering, the lamp is automatically changed
into red and this head is in patching mode. When the switch is at middle position,
this head is in patching mode if the lamp is red, or this head is in normal
embroidering mode if the lamp is green. When the switch is pushed to down
position, the lamp is off, which hints that this head is in stop mode. When the
switch is pushed to middle position from down position, the lamp will be green
and the head is in normal embroidering mode.
2-12 System's Working States
The machine has three working statuses:
1. Preparation status ⎯⎯ preset parameters; choose embroidery designs

and other preparation work

2. Embroidery confirmation status ⎯⎯ confirm the parameter settings to

enter the quasi-running status
3. Embroidery running status⎯⎯ embroidering
How to switch among the above work statuses?
In preparation status ( is displayed), after selecting pre-embroidery design
and setting the parameters, first press " " key, and then press " " key, now
the machine is in embroidery confirmation status ( is displayed). Finally, pull

the embroidery bar to right to embroider, which means the machine is in
embroidery running status ( is displayed).
In embroidery running status ( is displayed), pull the bar left to stop, now the
machine is in embroidery confirmation status (Again, pull the bar right, the
machine goes into embroidery running status).
In embroidery confirmation status ( is displayed), first press " " key. And
then press " " key to release embroidery confirmation status. Now the machine
enters preparation status ( is displayed).

Chapter 3 Disk Management
In disk management, users can input the designs in the disk to machine, and
vise versa; meanwhile, users can enjoy some common disk managing actions, like
erasing file, formatting disk, etc. Floppy disk and USB disk are both supported.
Users can save design data based on different types. The system recognizes
formats like DOS, FDR and ZSK. However, FDR and ZSK files are read only.
Design formats like DSB, DST and DSZ can be read. For data output, design will
be saved as DSB format.
3-1 Disk Choosing
Since the system support more than one storage device, please choose the
objective disk.
1. Click in the main screen

2. The system shows the current disk. Select the disk intended for further
operation. Press “ ” or “ ” to exit.

In this window all the storage devices will be displayed. Their information
includes the icons, words and numbers. The icon is the device type. Means
USB disk and means floppy disk. The words are the volume name of the
disk and the number in the brackets is for the disk’s digital symbol.
3. Enter the Disk Management Screen.

Press to switch between the two pages; press to show designs in next
page; press to change to other design pages.
Number Icon Name Description

File List Display the design files and folders of the
1.
disk in icons. It’s used to select files
Preview of designs Display the selected file and its
2.
information
Single- selection
3. /Multi-selection Switch between single- selection
and multi-selection
Select all Select all the items in the current folder,
4.
only in the multi-selection mode
Design input Input design from disk to memory
5.
Design output Output design from memory to disk

6.
Back up one directory Go back up one directory

7.
Refresh the disk Refresh current disk directory

8.
Create new directory Create a new directory on current disk

9.
Delete document Delete the selected documents

10.
Format disk Format the current disk

11.
Monogramming Operations relating to monogramming

12.
Help Display the help menu.

13.
14. Current route

Page information The current page and the total page
15.
number
Disk space information Show the total space and remaining space
16.
information
17. Design file date This is empty if it’s not a design file.
Design stitch number It displays the stitch number of the
18. design. (This is empty if it’s not a design
file.)


19. Names of the objects Names of the files or folders
Icons of the objects
for folder
20.
for files of DSB form
for files of DST form
3-2 Design Preview
1. Use “ ” to select the design in the disk management screen.
Design files and folders are shown by icon in the list. One page of the list contains
20 items. Turn pages to look for designs in another page. You can also use
to find design in other pages. The selected object has a blue frame.
2. Press Design Preview Key

The system reads the data from the disk and displays the design’s image
according to a certain ratio. At the same time the design’s information and
color-changing number will be displayed.
Note: More than one design is allowed to select for preview. Selecting more than
one design refer to chapter 3.3.
3-3 Select One or Several Designs
Before preview, input and deletion of files, the objective design has to be selected
first. The user can select one object for one time, and can also select several
objects for one time to improve efficiency.
1. Press “ ” to Select the Object
By default the first object in the page is selected while others are not selected.
Press “ ” to select a design and the icon and word information of the
selected design are showed in the blue square.
2. Press the Switch Key of Single/Multi-Selection

When selecting the objects, the system is in single or multi-selection mode. In the
single selection mode, one object is selected for one time and selecting another
object will automatically cancel the last selection. Press the switch key to switch
between the two modes. In the multi-selection mode the user can select several
objects. In the single selection mode the switch key shows when in the
multi-selection mode it shows .
3. Select More Than One Object
In the multi-selection mode, you may press “ ” to move to the object
and then press to select it. Repeat this operation to select more than one
object. And you can press cancel the selection.
4. Press to select all the objects in the current folder
The key is effective only in the multi-selection mode.
3-4 Design import
To input the design data in the disk to the machine’s memory, the user has to
select files from one or more disks first, and then input the design number and
name for the file to be saved.

1. Select one or more files in the disk
2. Click the design input key
The system asks the customer to input design number and name for system
saving.
3. The user inputs the design number and name.
The system provides the minimum available design number as the default value.
The customer can use the small panel on the right to change the value. When
several designs are input for one time, the user can only input the number of the
first design.

To modify the design number and name, click the object item in the left window
and modify it in the right window. After the modification click the modification
confirmation key “ ”, and the results will be save.
4. Click the confirmation key “ ”

3-5 Design Export
The user can output the design data in the system memory to the current disk.
1. Click the design export key

2. Select the design in the memory intended for output
The system displays the list of designs in system memory. The user selects the
designs intended for output, and then click .

3. Input of the design name for disk saving

The system uses the design name in system memory as the default design name in
disk.
To change the design name in disk, first select the item in the left window, and
then change it in the right window. After the changing, press to save the
result.
4. The system returns to the disk management screen.
During the above operation, you can press “ ” if you want to exit.
3-6 Folder Operation
1. Enter the directory
Select the directory and press “ ”. The system reads the item list of the
directory and refreshes the screen.
2. Return to the higher directory level
Press the key “ ” to return to go back up one directory and the screen will be
refreshed.
3. Make a new directory
Press the key “ ” and the system will ask to type in new directory, press the
key to build a new directory. System refreshes the current directory list.

3-7 Deleting Objects in Disk (Including Design Files and Folders)
1. Select one or more objects (See 3.3)
2. Click the deleting key “ ”
3. The system asks the user to confirm the deleting operation
4. press the key to delete; press “ ” to exit.

Note: If the user chooses to select a folder, the system will delete all the files and
sub-folders in this folder. If a file has the property of “only read” or “disk write
protection”, the file will not be able to delete.
3-8 Formatting a Disk
1. Select the disk device for formatting (read 3.1 for reference)
2. Click the function key

The system will change to the Format Disk screen, which is to display the storage
information of the current disk, alert information for disk formatting and
formatting process bar as well as Start and back button.
3. Click the Key “ ”

The system will begin to format the disk and show the speed with a process bar.
After formatting the system will display the prompt to show formatting success.
Click the returning key to return to the disk management screen.
Note: the system will format the disk in DOS format.

Chapter 4 Memory Design Management
Memory design management includes selecting embroidery designs, setting
designs and operations to create designs.
4-1 Memory Design Management Screen and Other Memory Design
Operation Screens
Click in the screen to enter the memory design management window.

The memory design management window includes: design image display area,
navigation and pagination area, information area, menu and memory design
management operation area. The design image display area can show 25 designs
at most, beyond that more pages are needed. Navigation and pagination area can
help switch to the designated page. The memory design management operation
area is to preview designs and set their order.

Press the key to shift among three pages; press to show designs in
next page. Press to change different design page.


1 Page information Show the current page and total
page information.
2 Total design and To show the amount of total
memory information design and memory
information
3 Design information Display the detailed
display information of the selected
design.
4 Design browsing Design will be showed in icon
mode. This is for design
selection
5 Select design In the embroidery preparation,
press the key to rework selected
design parameter screen, then
confirm design parameter and
use the selected design as
embroidery design.
6 Design preview Preview the design’s details,
scale up/down, move or imitate
the design.
7 Disk operation Please refer to chapter 3
8 Copy the selected Press this key to enter into

design design copy window
9 Design editing Editing the current design or
new design, please refer to
chapter 8
10 Delete design Press this key to delete the
current design
11 Set applique design Press this key to set applique
design
12 Satin stitch Set satin stitch compensation in
compensation memory
13 Packed design edit Press this key to enter into
combined design editing
14 Design divide To cut one design into two
15 Design union To combine two designs into

one
16 Generate high speed Press this key to enter into
design high-speed design generating


window
17 Create design from This function is to generate
packed standard design from combined
designs
18 design from parameter Generate design by parameter
19 Frame and make

design
20 Create outline from
design
21 Copy design with Copy design from setting stitch
varied stitch length length.
22 Setting design
parameters
23 Design come from PC
24 Letter pattern See chapter 9

parameters
25 help
26 Delete all designs Press this key to delete all

memory design.
See following specifications for each operation. Press the key “ ” to go back
to the memory design management menu.
4-2 Select One or Several Designs
Before any operation on designs, you must select the target designs. You can
operate on one design every time or operate on several targets in one time to raise
efficiency.
1. Press to select the targets.
By default the first item in the page is selected. Press key or the
design number key to select others. The icon and words of the selected target
appears in the blue squares.

2. Select the items one by one
In multi selection mode, press key or the design number key to
move to the target item and press to select it. Repeat the process to select
more. Or you can press to cancel the selection.

4-3 Selecting a Design for Embroidery
1. Select a new design (Ensure that the system is in preparation status .)
2. Press in the main screen to enter the memory design management

screen.
3. Select the design in the memory design image area of the memory design
management screen.
4. Press to rework the selected design parameter screen.
5. After reworking the design parameter, press“ ”to use the selected design
as the embroidery design. If the operation is completed, the system will close the
memory design screen to return to the main screen.
4-4 Design View
The selected design can be previewed in the memory design view screen
according to the designated way.


1 Design view area Display the selected design on the
designated way and speed.
2 Design information Display the design information.
3 Help Display the help menu.
4 Refresh display the Display the selected design again.

design
5 manual display Draw the design by single steps.
6 Draw/pause switch
is for switching
between drawing design and pausing
the drawing.
7 Speed down Decelerate the display speed.
8 Speed up Accelerate the display speed.
9 Zoom to window Display the design to the full size in

the design preview area.
10 Real size display Display the design in its original size
in the design preview area.


11 Zoom in Zoom in the design picture in the
design preview area.
12 Zoom out Zoom out the design picture in the
design preview area.
1. Click in the main screen to enter the memory design management

screen.
2. Select a design in the memory design image area of the memory design
management screen.
3. Click in the memory design screen to open the memory design preview
screen.
4. Click in the design preview area to control the design size.
Click to control the design display position. Click to locate
the design to the center. Click to control the design display speed. Click
to control the design display and pause. Click to automatically
switch to halt for single step design display. And click to resume normal
display. Click to refresh the selected design.

4-5 Copy the memory design
1. Press in the main menu to enter the memory design management screen.
management screen.
3. In the memory design management screen, you may press “ ” to enter its
operation screen. The system will automatically provide the available smallest
design number and default design name. If the user doesn’t want to change them,
go to 6 directly.
4. To input a new design number, press “design number” and input the new
number in the pop-up window, and then press to confirm the input.
5. To input a new design name, press “design name” and input the new name in
the pop-up window.
6. Press to confirm the input, carry out the copying operation, and return.
Press to cancel the copying operation, and return.

4-6 Deleting the memory design
This is to delete one or more designs in the machine memory.
2. Select the design. The user can choose to select one design or several designs
for one time.
3. In the memory design management screen, you may press to enter the
design deletion screen.

If you want to clear all the memory design, press .
4. Press to carry out deleting and then return to the design operation
choosing screen. Press to cancel deleting and return.

4-7 Design add applique
The system has two ways for applique embroidery: manual moving frame out and
automatic moving frame out.
Manual moving frame out: when embroidering to meet stop code, the machine
will stop automatically. Move the frame to the proper position for applique with
the manual frame-moving button. Then you may press and to return to the
stop point. At last pull the bar for embroidery.
Automatic moving frame out has two ways: moving frame to the offset point and
setting the moving distance. The operation is as follows: First set applique

embroidery function for the design. Then when embroidering to the applique
point, the machine moves to the offset point (which has to be set) or move out
according to the set distance. After applique pull the bar and the machine will
automatically return to the stop point to continue embroidery.
The following is how to add applique to the design:
management screen.
3. Press “ ” to set applique.

1 Design display Real-time display of the design when
area embroidering to the applique point
2 Sequence Show the sequence number of the
number list position to set applique point.


3 Stitch list Display the design stitches of the
position.
4 Type list The stitch code type
C: color-changing code
S: stop code
5 Option list applique option of the position:
1．No applique
2．Moving frame out to offset position
3 ． Moving frame out to a certain
distance
6 help
7 Appliqué Choose the distance for frame to move

distance out:（2cm to 99cm）or（-2cm to -99cm）
8 Whether to set Choose whether to set the offset
the offset position
position
9 applique Choose whether to set applique
embroidery embroidery.
choosing list
The design display area shows the design which is being set with applique. After
setting the applique position, the design will refresh and the result will show
directly.
4. Press to move the list to the position for applique. Then you can press
(which is after “Add Applique?”).
5. If choose to move the frame out to the offset position, press (which is
after “To Offset position?”). If choose moving the frame to a certain distance, first
press (which is after “To Offset position?”), and then press
to set the moving-out distance: （2cm to 99cm）or（-2cm to -99cm）.
6. Repeat 4,5, to set all the applique positions of the design.
7. Press to save the applique information and return to the design operation

choosing screen. Press to cancel setting and return.

4-8 Satin stitch compensate
This operation is to adjust the satin width in the design according to the need.
management screen.
3. Press the key “ ” to enter the satin stitch compensate g screen.
4. If don’t use the default values, press the design number and design name
and change them.
5. Press “X Space Between two Design” to input the new value, and then
press to confirm it. Press “Y Space Between two Design” to input the new
value, and then press to confirm it.
6. Press to adjust the satin width and save it as a new design to return to the
design operation choosing screen. Press to cancel the setting and return.

4-9 Edit packed design
The packed design means a design group packed from a certain (less than 99)
memory designs after setting their parameters. The packed design is set as
automatic continuous embroidery. In the memory design management screen the
icon of the packed design is shown as . To embroider a packed design, return
to the memory design management screen after creating or editing the packed
design. If it’s already in the embroidery preparation status, select the design and
the system will automatically return to the main screen. Then after embroidery
confirmation, pull the bar for embroidery. The user can also edit the packed
design into the common design by the editing function, so as to check and
embroider the design.
2. To edit a saved packed design, select the packed design first. To create a
packed design, carry out the following operations.
3. Press the key “ ” to enter the edit packed design screen.

The serial number indicates how many designs form the packed design and the
current operating design.

4. Set the parameters of the first design, including design number, magnify ratio,
rotating angle, design direction and priority mode. Please read setting the normal
parameters of Chapter 5 for reference.
5. Press to set more than one design for packing. And press to go
back to change the parameters of designs packed.
If the current design is not the first design of the packed design, it’s needed to set
the interval between it and the first design.
6. Press the key to save packed design.

7. Press to save or press to cancel the operation and return to the

design operation choosing screen.
4-10 Design divide
The action will help to make combined design to normal embroidery design.
1. Press the button on the main screen to enter the memory design
management screen.
2. Select a design.
3. Press the key “ ” to enter the design divide screen.

4. If you do not use the default value provided by the system, type in the design
number, design name, divide stitches by using the keyboard, then press to
confirm.


4-11 Combine the designs
This function is to combine two designs into a new one. The interval between the
two designs is the distance from the end point of the first design to the start point
of the second design.
2. Choose two designs in design choosing area. Press the key “ ” to enter its
operation screen. If More than two designs are selected, there will be a prompt to
tell you to reselect.
3. If you don’t use the default values, press the design number and design name
and change them.

4. Press to combine and return to the design operation choosing screen.
Press to cancel the setting and return.

4-12 “High speed design”
The function can cut the long stitch form into short ones, which let embroidery
course in consistent high speed.
1. Press in the main menu to enter the memory design management

screen.
management screen.
3. Press the key “ ” to enter the high speed design screen.

4. If don’t use the default values, press the design number and design name and
change them.
5. Press to create high Speed Design and return to the design operation
choosing screen. Press to cancel the setting and return.

4-13 Create design from packed
The action will help to make combined design to normal embroidery design.
1. Press the button on the main screen to enter the memory design
management screen.
2. Select a saved combined design.
3. Press the key “ ” to enter create design from packed screen.
Input the new design number and name as required.

4-14 Design from parameter
This is to change the setting of color-changing order and normal parameters such
as magnify and repetition, which is attached to a specific design, so as to create a
new design.
1. Click in the main menu to enter the memory design management screen.
management screen.
3. Click “ ” to enter the design from parameter screen.

4. Click “ ” to type in new design number and name.
5. Click “ ” to create a new design and return to the design operation
choosing screen. Click to cancel creating and return.

4-15 Frame and Make Design
The user often wants to embroider the boundary of a design before embroidering
it, so as to help later applique. The function of “Frame and Make Design” can
create such a design, and you can select the new design to embroider the
boundary.
1. In embroidery preparation status, stop the frame to the point, from which the
design will be embroidered.
3. Press the key “ ” to enter the Frame and Make Design screen.

4. Press to switch between satin stitch and jump stitch. Press the
manual frame-moving key to move the frame along the desired route. Press
at every turning point to confirm the trace.
5. Press and then after editing, and the system will prompt to
input the new design number.
6. According to the prompt, input the number of the new design (The computer
will provide a number for choice) and design name. Press to create the new
design.
7. Press to cancel the setting and return.

4-16 Create outline from design
This function is to create a new design according to the outline of the designated
design.

management screen.
3. Press the key “ ” to enter the create outline from design screen.
4. If don’t use the default values, press and type in to change them.
5. Press to create a design and return to the design operation choosing
screen. Press to cancel the setting and return.

4-17 Copy design with varied switch length
This function is used to create the same design with the different stitch length.
management screen.
3. Press the key “ ” to enter into operation screen.
If don’t use the default values, press and type in to change them.
4. Press to create a design with new stitch form and return to the design
operation choosing screen. Press to cancel the setting and return.

4-18 Setting design parameters
Each design has its setting of color-changing order and normal parameters such as

magnify and repetition, which can be checked and set here.
management screen.
3. Press the key “ ”. If the selected design is the current embroidering design,
the embroidery parameter setting screen will pop up. Please read Chapter 5 for
reference.
If the selected design is not the current embroidering design, the non-embroidery
parameter setting screen will pop up.
For setting parameters, please refer to 5.1 and 7.1. After setting, press the key
“ ” to save the parameters with the design. Press the key to return to
design operation screen.

4-19 Design come from PC
2. Press “ ” and the screen will show the following.
Type in design number and name, press the key “ ” to start importing.
After importing, system return to the design management screen. Press the key
to cancel.

Chapter 5 Managing of Parameters
In this system each design has its own settings of the normal parameters (like
magnify and repetition) and color-changing order. When a new design is selected,
the corresponding settings of normal parameters and color-changing order become
effective.
This system supports multi-missions at the same time. So it’s possible to set or
change the normal parameters and color-changing order of non-current designs.
To do this in the memory design management screen.
Pressing in the main screen.
As the image shows, when you move the cursor to a kind of parameters, system
shows the first few parameters (4 at most). Press to enter into certain kind
parameters.

5-1 Normal Parameters
Normal parameters include: “X&Y Scales”, “Rotate”, “Direction”, “Prior Mode”,
“Rep. Mode”, “Rep. Prior”, “X&Y Reps” and “X&Y Interval”. The user can
control the final embroidery results by adjusting these parameters. That’s why
these parameters are often to be adjusted when a design is selected.
In the embroidery preparation state “ ”, press in the main screen and
then to enter the normal parameter setting screen.
The way to set each parameter is similar. This chapter will explain how to set the
“X Scales” as an example and give the definitions of other parameters (Read 5.1.3
as reference).
5.1.1 Design directions

P P
FP
P
PF
F P
De sig n d ire c ti on
P P
PF
F F
Emb ro id ery sha p e
F F F
5.1.2 Setting of rotate
The user can make the design to rotate to a certain angle with this parameter.

Rota te 30 d eg re es
Desig n sta rt b it
5.1.3 Setting of X-scale
This parameter controls the scaling percentages on horizontal (X) direction, so as
to scale up/down the design.
X&Y Scales:
X : 2 0 0 %
Y : 5 0 %
Desig n sta rt b it Desig n sta rt b it

1. Press the option “X Scale”

Press “X Scale” in the normal parameter screen, and the screen will show the
parameter-setting window.
2. Set the parameter “X Scale”
Press the number panel in the parameter-setting window to change the scaling
ratio on X direction. The user can press to cancel the last input digit. Note:
some parameter value is input by pressing .
3. Press the confirmation key to save the change. Or press to exit.

5.1.4 “Rep. Prior”
There are two modes: X prior to Y and Y prior to X.

X interva l
Y in terva l
X p rior Y p rior
5.1.5 “Rep. Mode”
Currently, system supports common repeat and part repeat. Common repeat
means: after embroidering a design, repeat next design; part repeat is based on the
color, when finish embroidering one color, system moves to the next color.
5.1.6 “X&Y Reps”
X Reps of this parameter sets the number of rows in repetition, and Y Reps of it
sets the number of columns in repetition. The above diagram shows that X Reps is
3 and Y Reps is 2. The largest set value is 99*99.
5.1.7 “X&Y Interval”
The above diagram also explains the meaning of this parameter.
5.1.8 “Prior Mode”
There are two modes: rotating prior to scaling and scaling prior to rotating. When
the user has set the parameters “X&Y Scales” and “Rotate”, the design will rotate
first and then scale up/down with the setting rotating prior to scaling. Otherwise it
will scale up/down first and then rotate.

5-2 Setting of other embroidery parameters
Other parameters include 8 groups: embroidery assistant parameter, thread break
detecting parameter, frame parameter, main shaft parameter, thread-trimming
parameter, sequin parameters, special embroidery parameter and machine &
maintenance parameter. Some machine application parameters are for
administrators of the embroidery factories and can be set with administrator
password. Machine parameters are for the machine producer to use and usually
don’t need to be changed in working, which can be set with producer password.
Press to enter the “purview of machine parameter manage” screen, and then
you can set administrator and producer passwords as well as set parameters to
default. (See Chapter 5.4)
Refer to the appendix one for every parameter’s definition.
1. Press in the main screen.
2. The system enters the parameter setting screen, and press set the
parameters.
Note:
1、The number, name and value of every parameter are displayed in the parameter

list window.
2、 Parameter with can’t be changed unless the administrator password is

unlocked; parameter with can’t be changed unless the factory password is
unlocked. When a parameter is labeled by a number, then it can be changed by
pressing “ ”.
5.2.1 Setting Procedure for Other Parameters
The setting procedure is similar for each general parameter.
1. Select the parameter group.
Move the cursor to the parameter group to be changed, press “ ” to enter into
parameter setting. Move the cursor to the parameter and press “ ” to change.
Make sure the parameter is unlocked (See Chapter 5.4)
For instance, if you want to modify machine stitch count parameter, which is
located in the first item “D01 Needles <1, 15>”, “machine & maintenance
parameter”.
2. Press in the main screen, move the cursor to “machine & maintenance
parameter”, press “ ”:

Select the parameter to be changed, select D01 Needles <1, 15>, press “ ”:
Type in needle counts and press to save. Press the key to turn back to
machine & maintenance parameter.
Note: some of the parameter can not be typed in, you can only use to
select.
5.2.2 Introduction of Some Functions of General Parameters
There are brief introductions of the parameters in the appendix one. Here are
some functions used in embroidery.
1. Cyclic Embroidery
This function is to increase the embroidery productivity.
When the parameter“To Do Cyclic Emb.”is set as “Yes”, the cyclic embroidery
function is enabled and the icon will appear in the main screen. When this
function is enabled, after completing the designated design the machine will
automatically embroider it again without pulling the bar.
Usually cyclic embroidery accompanies repetition embroidery and special

punched designs and the parameter “Auto Origin” should be also set as “Yes”.
Thus when the machine is embroidering the back embroidery cloth-piece, the
front one can be replaced. After embroidering the designated design, the frame
will automatically return to the start point and the machine will automatically
embroider the front cloth-piece again and at this time it’s possible to replace the
back one.
2. Store Manual Color-changing
In embroidery confirmation status, the user can choose whether to store the
manual color-changing’s needle position into the color-changing order unit. Its
purposes are as follows: 1) If mistakes are found for the automatic color-changing
order in embroidering, the color-changing order can be modified with manual
color-change. 2) When a new design is embroidered with manual color-change
once, the color-change order is set for the design.
To use this function, the user should set the parameter “Store Manual Color” as
“Yes”. Note: the parameter value will automatically change into “No” at the end
of one design embroidering.
3. Brake Adjustment (A Must for New Machine)
This function is to adjust the control parameters for braking, so as to fit machines
of different mechanical characteristics, which also change with the machine
running. Thus this function can help the machinery parts to work better with the
computer. The function depends on the two parameters “Set Brake Para” and
“Main Motor Para.”.

“Set Brake Para” is to adjust the stop position of the main shaft. When the main
shaft often stops at less than 100 degree, the user can increase the parameter value.
When the main shaft often stops at more than 100 degree, the user can decrease
the parameter value. Thus the user can adjust the value to let the main shaft stop
close to 100 degree. The value can be set between 0 and 30.
“Main Motor Para.” is to adjust cooperation between main shaft motor and
machinery parts. The parameter value can be set between 0 and 30, and set as 0 in
most situations. When during braking the main shaft vibrate without moving or
rotate in the reverse direction, the user can increase the parameter value.
After adjusting these parameters, the user can press the task swift key on the panel
to return to the main screen. Press the key and , to check the effects of
the parameter adjustment. If the user is not satisfied with the effects, he can press
the swift key on the panel to return to the parameter setting screen, where he can
adjust the parameter setting again. Close the parameter setting screen in the end.
4. Forbidding Design Output
The function is to forbid copying the designs in memory (into the disk). If the
machine administrator set “No Output Design” as “Yes”, other persons are unable
to output the designs to the disk. If the user needs to output, he has to cancel “No
Output Design” first.
To use this function, the administrator password has to be set and it’s possible to
change this parameter after inputting the correct administrator password (refer to
5.4 machine management access).

5-3 Set User-defined parameter
This function should be used to work with “select user-defined parameter from
all”. “Set user-defined parameter” makes it easy to set frequently changed
parameters. The setting should follow the steps as below:
1. Press the key in the main screen, move the cursor to “select user-defined
parameter from all”.
2. Press the key “ ” to make this parameter as user-defined parameter, then

this parameter is been listed into user-defined parameter list. You may press
“ ” to cancel.

3. Press to go to the next page. Repeat the step 2. Then press
to shift between the pages. The user-defined parameters are labeled with .
4. Press the key to save and system goes back to machine parameter
screen.
5. Move the cursor to “set user-defined parameter”, press the key to

enter into user-defined parameter screen. The setting is similar to other parameter
setting.

Note: when you enter into the screen of user-defined parameter, system will
automatically clear the saved ones.
5-4 Purview of Machine Parameter Manage
For a convenient machine management, the common user can't access the setting
of all parameters; the roles of the customer are divided into the common user,
machine administrator and factory customer. The purview of the common user is
the lowest, can only modify the embroidery parameter of the machine, machine
administrator can also modify managing parameter, but the factory user can
modify all parameters.
Press “Purview of Machine Parameter Manage” to enter the following screen.

If the password is set and the machine administrator or the factory customer needs
to modify the parameter, he must input the password before any change. In this
screen you can also change password, save or restore parameters.
5.4.1 Unlock/Change the administrator password
When the machine leave the producer, it’s without password, namely the customer
can change all the parameter. After password setting, the common customer can't
modify the machine application parameter. The administrator has to input the
right password before modification.
1. Press in the main screen to enter into machine parameter management,
move the cursor to unlock/change the administrator password, press .

2. Move the cursor to “Unlock/Change the admin password”, press and

type in the old password then input a new one.
The administrator needs to input the old password and new password one by one.
The machine producer will tell the administrator about default password which is
in 4-9 digits. To prevent the user’s wrong operation, the new password must be
input two times in the same.
5.4.2 Machine Administrator cancels machine lock
After machine administrator setting the password, the machine is in lock. The
common customer can't modify the machine application parameters. To set these

parameters the administrator must input the administrator password or the factory
password.
1. Press in the main screen to enter into machine parameter management,
move the cursor to purview of machine parameter manage , press .
2. Move the cursor to “Unlock/change the factory password” and press .
System shows password input screen.
3. Administrator input password
After input the password, system is unlocked; you can modify related machine
parameters.
5.4.3 Administrator reset (or save) optimize parameter
The machine administrator can save and reset the optimized machine parameter
setting. If the user wants to save the parameter setting, he can press
“Administrator save optimize parameter”. The system only keeps one set of
optimized parameter setting. The new setting will cover the old one. If the user
wants to recover the saved optimize parameter, he can press “Administrator reset
optimize parameter”.
5.4.4 Change the factory password
The machine producer can modify all parameters. When the machine leaves
factory, the machine is unlocked. After password setting, the machine is in lock.

To change the machine parameters, you have to input password first.
5.4.5 Unlock the factory password
The procedure is similar to chapter 5.4.2.
5.4.6 Factory Save/Reset Parameters
The procedure is similar to chapter 5.4.3.
5-5 Initialize Parameters
This function can initialize the general embroidery parameters of the machine.
The system saves a group of default parameter values. The factory and
embroidery factory administrator can save their parameter settings. In this
operation it follows the following rules:
1. When the factory password and embroidery factory administrator password
are not set, all general embroidery parameters are initialized to take the default
values.
2. When that factory password has been set and unlocked, all general embroidery
parameters are initialized to take the default values.
3. When that factory password has been set and unlocked and administrator
password has not been set or has been canceled, all factory-authorized machine
parameters are recovered to factory saved values and other parameters are
initialized to take the default values.
4. When that factory password has been set and unlocked and administrator
password has been set and unlocked, all factory-authorized machine parameters
are recovered to factory saved values and administrator authorized machine

application parameters are recovered to administrator saved values and other
parameters are initialized to take the default values.
5. When that factory password has not been set and administrator password has
been set and unlocked, all general embroidery parameters are initialized to take
the default values.
6. When that factory password has not been set and administrator password has
been set and not unlocked, all administrator-authorized machine application
parameters are recovered to administrator saved values and other parameters are
initialized to take the default values.
5-6 Save all parameter to disk
This function helps to save and store the software information and machine
parameters.
5-7 Read all parameter from disk
The function helps to load saved parameters any time you want; no need to reset.
5-8 Adjust Parameters of X＆Y Servo Drivers
The type parameters are fit for the machine of main shaft using dahao servo
motor and driver. The factory can rework the parameters. You must input the
factory password if adjust the parameters or correspond to operation. The
operation process is as follows:
1、 Press in the main screen.

2、 The screen go into“Machine Parameters Operation”interface. Move
cursor to “Adj Parameters of X ＆ Y Servo Drivers” and press to

“Parameters of X＆Y Servo Drivers” window.
3、 Input factory password and move the cursor to correspond to item,
then press to the under operation.

5.8.1 Set the parameter
The type parameters setting is same as the other parameters, the explainer see
Appendix Ⅰ Parameter Setting List.
5.8.2 To inquire servo driver status
This operation can inquire the dahao servo driver status. Machine popup the
windows of X/Y servo driver status after carrying out the operation. Turn off
power and adjust dahao servo driver if the follow screen popup.

5.8.3 Write driver parameters
The currently parameters of setting X＆Y servo driver in the machine will save in
the servo driver after executing the operation. And the parameters can be saved if
turn off power.
5.8.4 Restore default driver parameters
The parameters of setting X＆Y servo driver in the machine will renew the dahao
servo motor driver parameters if you operate this item.

Chapter 6 Assistant Operation
6-1 Assistant embroidery operation
Press the other function key in the main screen to enter into assistant
embroidery operation screen.
If the frame origin has been set (see 6.2.3), in the state of embroidery confirm,
you can start design start point operation.
6.1.1 Resume Design Start
If the current design has start point, use this function to move the frame to the
start point saved before.
1. Follow the above instruction and enter into assistant embroidery operation
screen.
2. Move the cursor to “Resume design start” and press “ ”

3. Press the key “ ” to resume, system will move the frame to the start
position that already saved before; press “ ” to cancel.

6.1.2 Save design start
1. Move the frame to the embroidery design origin.
screen.
3. Move the cursor to “Save design start” and press “ ”

System will show:
4. Press the key “ ” to save the current frame position as the origin. Press the
key “ ” to cancel.
6.1.3 Auto to start position
This function is used for locating design center to the frame software center set by

the system (see 6.2.5). Thanks to this function, you can embroider the design to
the center of the frame.
screen.
2. Move the cursor to “Auto to start position” and press .
Press to confirm, system will find the central place and move to that
position; press to cancel.

3. System goes back to the main screen.
6.1.4 Stitch stop down
This function is intended for quilt embroidering. In embroidering, the needle will
stop and prick into the embroidery cloth to fix it. After releasing the cloth, move
the frame to the designated position. When the cloth is fixed on the frame again, it
is ready for the next operation. This function is available under embroidery
confirmation status.
screen.
2. Move the cursor to “Stitch stop down” and press .

3. Press “ ” to confirm operation, system let needle down to hold the cloth.
Press to cancel.
4. Release the cloth, confirm the operation after frame moving.
After releasing the cloth and move frame to desired position, press “ ” to
confirm, if you press , then the operation will be cancelled.

5. Back to main screen after confirm frame moving
Customers can hold tight the cloth and operate main shaft to go to 100°, then pull
bar to continue embroidering.
6.1.5 Setting another start
The offset point can be set at any point other than the start point. After setting it
and beginning to embroider, the frame will first move from the offset position to
the start position and start normal embroidery. After embroidery, the frame will

move back to the offset point. Moreover the offset point is also necessary for
frame to move out when applique. The function can only be used under the
embroidery confirmation status and before embroidering.
screen.
2. Move the cursor to “set offset point” and press .

3. Move the frame to the offset point.
The system will ask the user to confirm and input the coordinates of X and Y.
Press the frame-moving key to move the frame to the offset point and press
to confirm. Or press to cancel the operation.

4. The system will save the position of the offset point and return to the main
screen.
6.1.6 Set B Point
This function is selected and the user must customize.
This function is developed to solve the problem of inconvenience of
threading when thread break appears on giant machine.
When thread break appears, press the slow switch to let the machine trim,

then the frame will move to the point B. After reloading the thread, you can pull
bar to the right side to let the frame back to the stop point. Then proceed
embroidering.
I、 Setting Course
1、 Set the absolute origin, see 10.3 for details.
2、 Go into “Assistant Emb Operation” screen according to above
description.
3、 Move cursor to “Setting B Point Machine” and press key.

4、 Press the manual frame moving to move the frame to a proper
position.
5、 Press to confirm saving B point setting .

If you want to clear the point B, repeat the above operation .
II、 Notes
1、 When frame moves to the work-off point, there is only action on Y
direction.
2、 Frame will not necessarily move to the B point wherever thread breaks.
If the B point is set as the image below, then frame will be only moving above
B (a zone indicates the inner edge of the stand), after thread break, press the slow
moving switch, machine trims without letting frame go to B point; when frame is
moving under B (b zone indicates the outside of stand), after thread break, press
the slow moving switch, frame will move back to B point. If no action, please
check the machine.

3、 B point setting is as the image shows:
（1）If B point is above the line, then frame will back to B after slow moving.
There will be a long distance to go after threading.
（2）If B point is under the line, threading will be greatly influenced.
1、Frame 2、the best line for setting B point 3、edge of the table
6.1.7 Operation on AFC, Sequin and Coiling Devices
screen.
2. Operate according to the prompts.
Note: switch of valves (V1~V4) are for quilt embroidery. Other sequin and special
embroidery operations are detailed in different chapters.
6.1.8 Upper thread hold operation
The operation is fit for the machine having upper thread hold function. You can
open or close upper thread hold.
6-2 Other assistant operation
These operation include machine maintaining, information and some other system

setting.
Press in the main screen to enter the “Other assistant operation” screen,
which is a menu of function keys.
The screen is similar to that for embroidery helper function. The words on the
keys can help to explain their functions.
6.2.1 View Embroidery Parameter
The user can get information of the current design’s parameter and some machine
condition
1. Press in the main screen to enter the “Other assistant operation” screen.
2. Move the cursor to “view embroidery parameter” and press .

3. The system will show the current embroidery parameters.

They include: design number, total embroidery stitch, free memory, cycle
embroidery, frame origin, soft frame limit and offset point. Press to clear
or press to return.
6.2.2 View Statistics Information
This is to view the current design parameters and some machine parameters.
2. Move the cursor to “View Statistics Info” and press .

3. The system will show the machine’s statistics information.

In the above screen, the statistics information is displayed in a chart. The user can
press to clear the value and press to return.

6.2.3 Power resume setting/ frame start setting
Setting the frame origin position is the premise for saving the design’s start point
and setting frame protection when power off. So after machine installation or
maintenance, it’s necessary to set the frame origin point.
2. Move the cursor to “Power resume setting/ frame start setting” and press .
3. Use to choose between “Manual” and “Auto”.
Before setting the frame start manually, manually move the frame to the desired
origin position, and press “Manual”. Then the system will save the current frame

position as the frame start. In case of emergency stop because of malfunctions or
something unusual such as unexpected power off, etc. the machine will cancel the
“manual frame start” to avoid mistakes. If the frame has been moved after power
off, or if power on again after maintenance, you should do again the operation of
“frame start setting”.
If you hope the system automatically set the frame start, press “Auto”, and the
system will move the frame automatically and set the start position according to
the limit switch. So please ensure that the limit switch has been installed into the
machine and it’s effective.
6.2.4 Power resume
In case of frame having been moved after power off, this operation can be used to
restore the before frame position when the power is on again. The proper
performance of this operation is based on the “Frame start setting”. In addition,
if the power is off in the process of embroidering operation and the frame has not
been shifted, you also can directly pull the operation bar to continue embroidering
after power is on again.
2. Move the cursor to “Power resume” and press .
3. Press “ ” to confirm or “ ” to return.

If it is “auto” in “set frame origin”, the machine will automatically move to the
frame origin point and then back to embroidering position before power-off. It
will be invalid if the operation of manually set frame start is done.

6.2.5 Set embroidery scope in software
This function is to set embroidery scope in software. It’s the basis to locate design
in the central place of the frame.
2. Move the cursor to “set embroidery scope in software” and press .

3. If software protection has already been set, system will ask to clear original
settings.
4. Press the key to set top-right corner.
Use frame moving key to move the embroidery frame, after you confirm the
top-right corner, press “ ” to confirm.

5. Move frame and type in the bottom-left corner.

Use the frame moving key to confirm the bottom-left corner, press “ ” to
confirm.
6. System will record frame software protection.
6.2.6 Set system clock
In date and time screen, users can check and modify the current date and time.
2. Move the cursor to “set system clock” and press .
3. Use the digital key to type in numbers; use to find the number you
want; use to select option.

4. Press the key to modify, press “ ” to return without save.

6.2.7 Language Choice
The system supports Chinese / English /Espanol/Turkish language.
2. Move the cursor to “Display Language” and press .
3. Move the cursor to the language of you want, then press to confirm or
press “ ” to exit.
6.2.8 Machine Soft Information
1. Press in the main screen to enter the “Other assistant” screen.
2. Move the cursor to “machine soft information” and press .

This function is used for checking the software of upper and lower machine, press
to exit.
6.2.9 Help
2. Move the cursor to “Help” and press .
It displays the help information, press or to shift between the
pages.
6.2.10 Machine Test
This operation is provided to only maintenance engineers to use,

Embroidery workers don’t do this. This operation contains some mechanical work.
Please pay attention to personal and equipment safety.
This function is mainly used for machine adjustment, maintenance and checking,
including:
Test Encoder parameters
Test main shaft speed

Rotate main shaft to fixed angle
Test the pull bar
Test the limit switches
Test the head solenoids
Test trim solenoids/ motor
Test holding solenoids
Test hook solenoids/ motor
Splay Scissor’s Angle
Trim Motor to Find Origin
Test thread breakage
Thread Breakage Statistics
Count of Roller Thread Breakage Device
Test sequin device on/off
Sway Zig Rod to 100
Test lift clamp foot
Test Upper Thread Hold Function
Sequin A send one sequin
Sequin B send one sequin
Sequin C send one sequin
Sequin D send one sequin
Sequin equipment push valve 1.
Sequin equipment pull valve 1.

Note: for sequin and special embroideries, refer to the related chapters.

Chapter 7 Other Operation
7-1 Operation on color-changing order
The design’s color-changing order is saved with the design.
Press the key in the main screen. You can operate color-changing order in the
following screen.
7.1.1 Input Color Line
1. Move the cursor to “Input color line” and press “ ”:

2. Press the digital key (Note: the number you type can not be over the needle
count) and type in the color-changing position. The color-changing position and
relative order are displayed on the screen.
If it is a special embroidery position or sequin embroidery position, see detailed
operations in related chapters.
Press the key “ ” to save the color-changing order; press the key to exit
without saving.
7.1.2 Modify color line
1. Move the cursor to “modify color line” and press “ ”:
2. Press the key “ ” to select the position to be modified. Press the digital
key to input needle position (if you input a special embroidery needle position or
a sequin embroidery position, see related chapters for details.)
If you want to modify the next color, you can repeat step “ ”. Press the key
“ ” to save the color-changing order; press the key to exit without

saving.

7.1.3 Replace a needle
1. Move the cursor to “replace a needle” and press “ ”:
2. Press the digital key to input “replacing from needle” and press to
confirm and type in digits in “replacing to needle”, then press to save or
press the key to exit without saving.

7.1.4 Set color of showing design
In order to make showing effect close to the real embroidery design, the system
supports setting of each needle bar color. The needle bar color can be saved with
the color-changing order.
1. Move the cursor to “set color of showing design” and press “ ”:

There are altogether 40 different colors for you to choose.
2. First you should press to select the needle bar to be set, then press
“ ” to the desired color. Press to confirm.
3. After setting, press to save the needle bar color setting and return, or
press the key to return without saving.

7-2 Design border operation
Press the key on the main screen.
7.2.1 Check the boundary of a design
The function is used for checking current design boundary information and
displaying.
1. Move the cursor to “check the boundary of a design” and press “ ”. System
will then display it in the window:

2. Press “ ” or “ ” to close the window.

7.2.2 Move the frame along the boundary of a design
The function can drive the frame moving along the border. If it moves beyond
limit, system will correct it to avoid over-limit in real embroidery.
1. Move the cursor to “move the frame along the boundary of a design” and
press “ ”:
2. Press to let the system go along the border, or press the key to
cancel.

3. After finishing moving, system returns to the design border operation screen.
7.2.3 Create design from outline
1. In the main screen, you can move the cursor to “Create design from outline”
and press “ ”:
2. You can type in design number and name.
3. Press the key “ ” to save the design or press “ ” to cancel.

7.2.4 Frame to generate design, then embroider back
Before embroidering a design, you may wish to embroider a sign for positioning
applique.
1. In preparation state, you can move the cursor to “Frame to generate design,
then embroider back” and press “ ”:

2. Press the key to shift needle (flat or jump). Press the manual
frame moving key to let the frame go along the border. Press at each
turning point.
3. After editing, press and , then system will ask for new design
number and name.
4. You can type in and press “ ”.
5. Press the key to give up current operation and return.

7.2.5 Embroider a “+” in current position
System will embroider a “+” at the current position, the size can be adjusted.
1. In design border operation, you can move the cursor to “Embroider a ‘+’ in
current position” and press “ ”:

You can set the length of + in both X and Y directions:
2. After setting the length of “+” in both X and Y directions, press ,
System will generate a temporary information of the “+” and return to the main
screen. Now the label is displayed. You can pull bar to embroider a cross.
7.2.6 Frame and embroider back for one line
1. In design border operation, you can move the cursor to “Embroider a ‘+’ in
current position” and press “ ”:
2. Move the frame to the start point of the line, press to confirm the first
point. System will ask to move to the end point.

Move to the end point and press the “ ” to confirm the second point.
3. System will generate temporary information of the line and return to the main
screen.
Now system displays on the main screen. Pull bar to embroider line, after
that, system returns to the embroidery preparing state.
7.2.7 Embroider the boundary of current design
The function can measure design border data and generate a temporary data for
users.
1. In design border operation, you can move the cursor to “Embroider the
boundary of current design” and press “ ”:
Press the key to confirm, press to cancel.

2. System will generate temporary information of the line and return to the main

screen.
Now system displays on the main screen. Pull bar to embroider border, after
7.2.8 Embroidery true boundary of current design
System will generate boundary data according to the current design. Pull bar to
embroider.
1. In design border operation, you can move the cursor to “Embroider true
boundary of current design” and press “ ”:
System will generate a temporary data according to the boundary design data and
ask user to confirm.
2. Press to confirm and then system will return to the main screen.
Now system displays on the main screen. Pull bar to embroider border, after
7-3 Positioning Idling
This function is only available in embroidery confirmation status .

According to the user’s needs, this function enables the frame to the designated
position without embroidering. The user can set the forward/backward positioning

idling by stitch number, color code and stop code.
Press in the main screen to enter the positioning idling screen, where there
is a list of function keys. You can press these keys to perform different idling
functions.
7.3.1 Go ahead stitches

1. In the screen of positioning idling, move the cursor to “go ahead stitch” and
press .
2. You may type in the required “go ahead stitch”.
System goes to the screen of “go ahead stitch”. You can press to confirm or
press to cancel.

3. System goes back to the main screen. You can pull bar right to idle to certain
stitches.
7.3.2 Go back stitches

It is similar to the operation of “Go ahead stitches”. In step “3”, you should pull
bar left.
7.3.3 Next Color Code

1. In the screen of positioning idling, move the cursor to “next color code” and
press .
2. Press the key . System goes back to the main screen. You can pull bar right
to idle to next code. Press to cancel.

The other three positioning idling items is similar to above.
7-4 Reset X/Y Displacements
This is to clear the X and Y displacements.
1. Press on the keyboard.

2. You may press “ ” to set X and Y values as 0. Press the key to

cancel.
The user can check the values in the main screen.

Chapter 8 Memory Design Edit
You can edit common designs in the memory through this function, or establish a
new design.
8-1 Start Editing Design
Press in the main screen to enter the memory design management screen.
Select the design and then press “ ”.
Press to edit the current design, press “ ” to edit new design.

Note: the design you selected can not be combined design, or system will warn “It
isn’t common design”.

8-2 Design Edits Operation
8.2.1 Summarize
1. Design preview window: use for preview design. In view, use “＋”mark the
position of current needle. The needle trace of current stitch use white and
outstanding manifestation. The scale information is displayed on the top-left while
the positioning stitch type is shown at the top-right (use to shift); the
detailed information is displayed to the bottom of the screen.
2. Document operation: to save design.
3. Image operation: to scale image
4. Needle positioning panel: use for positioning the current needle (needle to be
viewed and edited).
5. Needle editing function: use for switch stitch code, insert needle, delete needle
and move the needle position.
6. Help: press this key to view the instruction of certain key.
7. Page shifting: press this key to shift between the two pages.

8.2.2 Document and View Operation
Keep the current design to a new document.
Enlarge or zoom view. The scaling is 150% every time.
Reduce the design thus can see the all of the design. If the design size is
smaller than show scope of the screen, then show the design with the actual size.
Enlarge the design to 450% to thus look into the detail of the needle
vestige." Current needle" will move the middle position of the screen
automatically.
Review the online help of the design edit operation screen.

8.2.3 Key for Positioning Stitch and Editing Stitch
Move the current stitch to a certain stitch. At the same time use “＋”to mark the
position of “current stitch” in the window of design preview. If the “current stitch"
is not in the window, the system will renew the display and move “current stitch"
in the centre of window.
1. positioning stitch
to the design start point
to the design end point
to last color changing code
to next color changing code
to last jump code
to next jump code
Press to position high speed current stitch position, press low

speed current stitch position, press to shift among 1&10,100&1000,

lockstitch, stop, color-changing, jump and sequin.
2. editing stitch
Click to add one designated stitch type at present position. Press
to change stitch type. Press to confirm and cancel.
Click to delete present stitch.
Click to move stitch. Press direction key on the panel to move present
stitch position. Press to change moving stitch speed state among high
speed, middle speed and low speed.
Press to add series satin stitch at design trial.

Move coordinate index to propriety position in pressing direction key. Press
to add one stitch trace at present position. Move coordinate index continue
to add more stitch trace.
Press to switch coordinate index speed among high speed, middle

speed and low speed.
After editing , click and type in design name and number. Press
to confirm and cancel.

Chapter 9 Letter Design
You can through the letterform storage that saved in system, to create pattern file
based on letter.
9-1 Enter Letter Design Operation
Click pattern management key on main screen, then press and

to enter into pattern management screen.
9-2 Enter Char String and Basic Parameter
After open the window of parameter input, enter into pattern string input window
automatically. Move the cursor to related parameters and press . After
adjustment, press again to save.

1. “Char string”: means the letter list that will be embroidery
2. “Font style”: means the letterform that use for embroidering letter. The
letterform was selected here will use for all of letters.
This is the font style window:
You can press “ ” to move the cursor to the desired font and
press .
3. “Arrange type”: the formation of letters. There are four types: “Plane”
“vertical” “up arc” and “down arc”.
4. “Letter space”: means rank space between letters, the unit is 0.1mm.
5. “Char direction”: it’s to decide whether every letter’s angle changes with its
position in the arc when “arrange type” is arc.
6. “String rotate”: means rotate angle for whole letter bound.
7. “Char height scale”: means increase or reduce letter high.
8. “Char width scale”: means increase or reduce letter width.
9. “Density”: means distance between each stitch of born letter pattern. The value

is smaller, the density is bigger.
10. “Char rotate”: means rotate angle of each letter that opposite to centre of it
selves.
11. “Auto change color”: whether add change color code before each letter.
12. “Show hint window”: whether to show hint information window during the
operations.
After establishing letter pattern parameter, you may click to enter window
of “create character pattern”.
A. Create character pattern
“create character pattern” screen is shown as diagram:
First usually set char string parameter as arrange type, letter space and so on
Then select one letter to adjust its arrange.
Create character pattern: the central cross mean coordinate, intersection is origin
（0,0）. The letter rank surrounds origin automatically.
B. View and file operation
is basic letter parameter operation.
/ “Needle trace”: show/hide needle trace, hide needle trace can
improve operation speed.

“Zoom out": enlarge to show the window and to look into the detail part of
the letter pattern.
“Zoom in: reduce the show window of letter pattern.
“Fact”: Show the letter pattern with the actual size. At this time, the size of
pattern in screen is equal to actual size.
“Center”: Zoom to see the diagram, show the whole pattern.
“window shift": Click this key, it will turn dark. Press to
move the window. Letter design moves with the window.
“Save”: Used for save letter pattern that just edit. After clicking that key,
appear the window that can input the pattern number and pattern name. According
to the pattern name and pattern number that need modification (the serial number
does not modification generally), then click to save or to quit.
“Help": Online help of “create character pattern” screen.

C. Adjust key of whole rank parameter
If after you edit individual letter, then again to adjust whole rank parameter, the
editor of the individual letter will be probably overlay.
"Fix the letter direction": When rank the letter bound by round arc
method, the letter angle not change with the position of round arc, but be
equal to a certain angle fixedly.

“Angle follow”: when rank the letter bound by round arc method, the
letter angle change follows behind the position of round arc (perpendicularity in
arc)
“Radian increase”: When rank the letter bound by round arc, enlarging the
radian of reference round arc.
“Radian reduces”: When rank the letter bound by round arc, reduce the
radian of reference round arc.
“Whole anticlockwise rotate”: anticlockwise rotate for whole letter bound.
“Whole clockwise rotate”: clockwise rotate for whole letter bound.
"Extend letter space”: Increase the distance between the letter.
“Reduce letter space”: reduce space between letters.
D. Pick out letter adjustment key

“Select switch”: switch selected letter. Must pick out a certain letter and
then can carry on the editor for it. When there is a red“＋”in the center of letter,
meaning the letter to is pick out, such as： . The system default will pick out all
letters. After click “select switch” key, pick out the first letter, then click, pick out
the second, depend on this kind to push. After picking out the end letter, then click
“select switch”, will pick out all letters again.
Repeat the operation and cycle in above order.
“Letter scale”: to adjust the selected letter, press to increase height,
press to decrease height, press to increase width while press to

decrease width.
“Letter move”: after pressing this key, press to move
toward certain direction.
“Anticlockwise rotate”: With the letter as centre, ( “＋” in the centre of
letter) rotate selected letter toward anticlockwise direction. Such as:
“Clockwise rotate”: With the letter as centre, (“＋”in the centre of letter)
rotate selected letter toward anticlockwise direction. Such as:
“Density increase”: Increase stain stitch density of the born letter pattern.
Such as:

“Density reduces”: Reduce stain stitch density of the born letter pattern.
Such as:
“Level overturns”: Left and right overturn the selected letter.
“Flip vertical”: Up and down overturn the selected letter.
“Change color switch”: Establish or cancel change the color that was set
before selected letter.
“Change font”: change letterform of selected letter. After clicking this key,
will flick the dialog box of select letterform, choose one of letterform that you
wished, and confirm.
Press to return the window of letter pattern input. If you need to change
embroidery letter bound, can click this key to return back the previous screen to
carry on the modification. All of adjustment for individual letter in this window
will disappear.
9-3 Character Pattern Save
After finish letter pattern editor, click key. Appoint the pattern number and
patter name in the pop-up window, then click key to save.
Click key to confirm keep successfully, if do not need to continue to edit the

letter pattern, click key to exit.

Chapter 10 D type sequin embroidery
10-1 Brief introduction on sequin embroidery
Sequin embroidery is composed of sequins and threads. We choose those hard
materials with smooth surfaces as the sequins. Embroidery works will be shining
with these sequins attached. Design with Sequin codes has its own way of
designing.
D type multi-sequin embroidery of BECS-C18 machine is divided into two groups:
one is normal multi-sequin design, made by normal design making method. The
other one is special multi-sequin design made by normal design software with
special making method attached.
For normal one, you should set sequin mode when you modify the color-changing
order. Special multi-sequin design can be directly embroidered after modification
of color-changing order.
Meanwhile, the machine can automatically change normal design to special design
during the process of design import. The special design saves all the sequin of
normal design as sequin A. If you want further modification, you can use “sequin
edit” to modify.
Note: see appendix 4 for detailed design making rules.
A. Applied Scope:
This system applies to sequin embroidering control system which combines
normal embroidering mechanism and sequin sending mechanism.

B. Features and Functions:
1. Two sending sequin modes: Roller and Lever;
Roller: the core part is a wheel-like device in the whole mechanism. Its operating
principle is to wheel continuous towards one direction to send sequins into
position.
Lever: the core part is staff linkage. Its operating principle is to move
back-and-forth to send the sequins into position.
2. Sequin mending and sequin sending mechanism are two independent actions
3. Delivering a sequin by operating either manual separated head or centralized
4. Display working status separated head
5. Type of sequin sending and angle can be changed by operating on the control
panel.
C. Specifications
1. Sequin diameter range: 3mm,4mm,5mm,6.75mm and 9mm;
2. The maximum speed for sequin embroidery is 850 rpm.
D. A/B/C/D means four delivering sequin equipment in underside depiction. If all
four sequins are delivered, A will be on the top, then B, C and D.
10-2 Embroider sequin
You may follow the steps in sequin embroidery:
1. Input design with sequin code (see 10.3)
2. If you want, you can do design selection and editing (see 10.4)
3. Set sequin parameter (see 10.5)

4. Check and make possible adjustment to the sequin delivery device (10.8)
5. Set color-changing order (see 10.6)
6. Back to main screen and confirm embroider
7. Pull bar to embroider
Note: You must not touch valve switch during embroidery, or it will cause damage
to the device.
10-3 Input sequin design
Press the key in the main screen to enter into disk selection menu. Select
design import and press .
You should type in design number and name, then press to confirm. In the
blank of “is new format multi-sequin design”, use or to select a import way.
Choose “Yes” to save as the special sequin design anyhow .To the normal sequin
design, changed sequin design save multi-sequin as “A” type sequin. If you
choose “No”, normal sequin design remains as normal sequin design, while
special multi-sequin designs will be saved as special multi-sequin design.

10-4 Sequin design edit
This function is to edit sequin design. All the designs will be saved as special
multi-sequin design.
1. Press in the main screen:
2. Press direction keys to select design with sequin code. Use key to turn
page and select key:

3. Press the key to search sequin:
1） Move the cursor to this menu and press to select one sequin:
This helps users to directly select a sequin to edit.
2） Move the cursor to this menu and press to select one sequin by
stitch:
This helps users to directly select a sequin according to its needle order to edit.
3） Move the cursor to this menu and press to select sequins by group:
This helps users to directly select a group of sequins every time. (Note: in the
same group, sequin interval should be within 12.7mm, or they are two groups)
4） Move the cursor to this menu and press to select sequins by color.
This helps users to select all sequins with same color.
4. Press key to display

1） View all of sequins
Select this menu and press to show all the sequins in the window.
2） Zoom in of the sequin
Select this menu and press to zoom in the sequin.

3） View all of Design Stitches
Select this menu and press to display lockstitch, sequin stitch and other
stitch codes.
5. Sequin mode selection
There are altogether 15 sequin modes for users to choose: A、B、AB、C、AC、
BC、ABC、D、AD、BD、ABD、CD、ACD、BCD、ABCD.
Sequin name are A, B, C and D. If all four sequins are included, A will be on the
top, then B, C and D.
6. Edit of Alternate Sequin
You should first select a group of sequins or sequins with the same color, then
press to edit.

1） Use or to select sequin mode and press to confirm. Sequin

name are A, B, C and D. If all four sequins are included, A will be on the top, then
B, C and D.
2） After that, press and delivery sequin number ranging from 1 to 9999
is desired. If use same sequin mode, import “1” and confirm by pressing .
3） Use or till you see “OVER” in the blank of “Input Sequin M”.
Press to confirm.
7. Save as one new design
After sequin design edit, use to save:
10-5 Parameter setting about multi-sequin embroidery
Press the key in the main screen and select “sequin parameter”:

(1) Speed for Sequin R(L):
The speed depends on the sequin size. However, sewing the same sequin with
different mechanical structure, the acting angle could be different, which is
directly related to the maximum speed.
Note: the maximum speed of flat embroidery should be higher or equal to speed

for sequin embroidery.
Move the cursor to this parameter and press to enter. Use or to modify
the value and press to confirm.

(2) Auto start for sequin:
When the setting is “Yes”, system will start embroidering sequin automatically.
When the setting is “No”, machine needs manually start.
(3) Time of Sequin Action:
This is to set the time period from sequin device goes down to embroidering (0-15,
the default value is 2). If the sequin device is controlled by valve, use the default
value; if it is controlled by motor, choose 4-5.
(4) Sequin off after T.B.
When the setting is “Yes”, sequin presser foot will be lift up automatically in case
of thread break. When the setting is “No”, the sequin device needs manually
lifting the presser foot.
(5) Sequin Ind. Up Down
When the setting is “Yes”, it is independent lift up. When the setting is “No”, it is
collective lift up.
(6) Motor Number of R (L) Sequin
Tihis parameter is set by mechanism . If there is no sequin device, then you should
set to “0”.
the number and press to confirm.

(7) Set 3/4/5/6.75/9mm of R(L) Sequin
This is to set sequin delivery angle. If it is roller, it should be set to single way; if it
is lever, it should be set to double way. The parameter is closely related to
“left/right sequin device A/B/C/D size and color”. For example, “A size&color of
R sequin” is set to “4mm X color”, then the angle value should be “Set 4MM of R
Sequin”.
the delivery mode and press to confirm.

(8) A/B/C/D size&color of R/L sequin
Setting of this parameter depends on the mechanical structure. The order from A to
D is from front to back. Move the cursor to this parameter and press to enter.
Use or to modify the delivery mode and press to confirm.

Note: “Motor Number of R (L) Sequin” is closely related to “A/B/C/D size&color
of R/L sequin”. For example, if “Motor Number of R (L) Sequin” is set to 2,
then it only displays “A/B size&color of R/L sequin”.
(9) Sequin Gap Num of R(L) Sequin
This is to set gap number. If there is no gap, then it should be set to 0.
the delivery mode and press to confirm.

10-6 Change color order and set sequin mode
User must set sequin mode before setting color-changing toward normal
multi-sequin design, but expert multi-sequin design don’t need set multi-sequin

sequin mode.
Detailed operations are:
1. press the key in the main screen:
2. Move the cursor to “input color line” and press to enter.

3. Input color-changing position by typing in digits key (Note: the number you
typing in can not go beyond needle count). System will show needle position
and related needle position order. If the first/end needle is multi-sequin device,
it will require sequin delivery mode. If it is single sequin device or special
multi-sequin design, it is not necessary to set. For example the end needle is 6,
then after you type in 6, it will show:

Setting sequin delivery mode:
a) Press digital key confirm embroidery needle position, it will show “input
sequin mode” when there is sequin device.
b) Use or to modify the delivery mode and press to confirm. A

stands for front motor delivery; B stands for middle motor delivery and C
stands for rear motor delivery. AC stands for front/rear motor overlap
sequin, AB stands for front/middle motor overlap sequin, BC stands for
middle/rear motor overlap sequin and ABC stands for front/middle/rear
motor overlap sequin.
Note: if there are only two motors, then B stands for rear motor.
c) After pressing , you should type in desired sequin delivering number. If

it requires same mode before color-changing, then type in “1” and
press .

d) Use or till you see “Over” in “input sequin mode”, then press
to confirm.
For example: a machine with needle 9 as its end needle (sequins 3, 5, 7mm); first
needle is single sequin (9mm). The requirement is 7mm at first, then 3 & 5mm
overlap, then 5 and 7mm alternate embroidery, then sew 9ps of 3mm, 8ps of 5mm,
4ps of 7mm, 6ps of 3 & 7 overlap sequins, at last, use first needle to embroider
9mm sequins.
Settings:
（1）
① press 9，it will show sequin delivery mode screen；
② Use or till you see “C” in “input sequin mode”, then press
to confirm；
③ press“1”，then press to confirm；
④ You should use or till you see “Over” in “input sequin mode”,
then press to end the first setting.

（2）
② Use or till you see “AB” in “input sequin mode”, then press
to confirm；
④ You should use or till you see “Over” in “input sequin mode”,
then press to end setting。

（3）
② Use or till you see “B” in “input sequin mode”, then press
to confirm；
④ You should use or till you see “C” in “input sequin mode”, then
press to end setting；
⑤ press“1”，then press to confirm；
⑥ You should use or till you see “Over” in “input sequin mode”,
then press to end setting.

（4）
② Use or till you see “A” in “input sequin mode”, then press
to confirm；
③ press 9，then press to confirm；
④ Use or till you see “B” in “input sequin mode”, then press
to confirm；
⑤ press 8，then press to confirm；
⑥ You should use or till you see “C” in “input sequin mode”, then
press to end setting；
⑦ press 4，then press to confirm；
⑧ Use or till you see “AC” in “input sequin mode”, then press

to confirm；
⑨ press 6，then press to confirm；
⑩ You should use or till you see “Over” in “input sequin mode”,
then press to end setting.
（5）press 1, then press to end the whole setting.

Note: if it is single sequin, it is not necessary to set sequin delivery mode.
10-7 Manual operation of sequin embroidery
It has two ways of operation, centralized operation and separated operation.
1. Centralized Operation
Centralized operation can be divided into three parts: “sequin start”, “sequin end”
and “Send sequin”.
(1) Press the key in the bottom of the screen and then select “sequin start”,
then press to let all the sequin presser feet go down.
(2) Press the key in the bottom of the screen and then select “sequin end”,
then press to let all the sequin presser feet go up.
(3) Press the key in the bottom of the screen and then select “send sequin”,
then press to let all the devices send out one sequin at the time you press
the key (sequin presser foot should be down at first).
2. Separated operation
Thread break switch is embroidery switch. When thread break switch is at the
down side, neither flat embroidery nor sequin embroidery is available.
Thread break warning lamp is mounted on the sequin sending device, which

offers the operator with easy view.
Note: when the manual valve control switch is in the middle, blue lamp is on,
which indicates a perfect condition of sequin embroidering.
Location of the sequin switch board
10-8 Debugging multi-sequin embroidery
1. Separated debugging
1） deliver A sequin of front motor action
Shift the switch to the lower side, thread break detect switch turns green, press
manual sequin delivery button.
2） deliver B sequin of middle motor action
Shift the switch to the lower side, thread break detect switch turns red, press
manual sequin delivery button.
3） deliver C sequin of rear motor action

Shift the switch to the lower side, thread break detect switch turns to the lower
side too, press manual sequin delivery button.
2. Centralized debugging
Press the key in the main screen and press to enter into “machine
test” window.
Then you can select related menu to adjust.
10-9 Sequin mending
After thread break or manually turning on the red lamp, pull bar and the machine
state is in sequin mending. All the sequin devices will lift up; machine stops when
it backs to the stop embroidering point. Pull bar again to let the sequin device (on
mending head) down for mending. When it reaches the stop point, machine stops,
then other sequin devices will be down to continue normal embroidery. “Patch
count” in machine parameter setting is ineffective in sequin mending.

Chapter 11 J type Sequin Embroidery
Chapter 11 J Type Sequin Embroidery
11-1 Brief Introduction on J Type Sequin Embroidery
Sequin embroidery is composed of sequins and threads. We choose those hard
materials with smooth surfaces as the sequins. Embroidery works will be shining
with these sequins attached. Design with Sequin codes has its own way of
designing.
A. Applied Scope:
This system applies to sequin embroidering control system which combines
normal embroidering mechanism and sequin sending mechanism.
B. Features and Functions:
1. Two sending sequin modes: Roller and Lever;
Roller: the core part is a wheel-like device in the whole mechanism. Its operating
principle is to wheel continuous towards one direction to send sequins into
position.
Lever: the core part is staff linkage. Its operating principle is to move
back-and-forth to send the sequins into position.
2. Sequin mending and sequin sending mechanism are two independent
actions
3. Delivering a sequin by operating either manual separated head or
centralized
4. Display working status separated head

5. Type of sequin sending and angle can be changed by operating on the
control panel.
E. Specifications
1. Sequin diameter range: 3mm to 9mm;
2. The maximum speed for sequin embroidery is 850 rpm.
11-2 Operating Sequin Embroidery
You may follow the steps in sequin embroidery:
1. Input design with sequin code
2. If you want, you can do design selection and editing
3. Set sequin parameter (see 11.4)
4. Adjust sequin delivery device
5. Change the needle position to sequin embroidery position (see 11.3), make
sure state control switch is set to the middle, blue lamp is on.
6. Back to main screen and confirm embroider
7. Pull bar to embroider
Note: You must not touch valve switch during embroidery, or it will cause damage
to the device.
11-3 Color changing
Before setting color-changing, you should set sequin mode.
11.3.1 Setting sequin mode:
1. Press the key in the main screen:

2. Move the cursor to “set sequin mode” and press to enter.
3. Press “ ” to select relative parameters (for example Sequin Maner0), then
press to enter into its first parameter, use “ ” to select sequin type.
4. Press to enter into the following menu, use “ ” to select sequin

delivery motor (free combination of A/B/C/D motor)

5. If you choose to “over”, press to enter into the following menu. Setting of
sequin Maner 0 is finished.
If you choose any combination from A/B/C/D (for example motor A), press
to enter the following menu and type in sequin delivery count (0-99) of design
border upon stitch position .

If you type in “0”, press “ ” to enter the following menu and the sequin setting
is finished.
If you type in other numbers, then it will return to the step 4.
You may press in any of above steps to save or press to quit.

For now, our system supports 8 different selecting ways at most.
11.3.2 Sequin color changing setting

1. When you set the color changing order, if you type in needle position (for

example 6), then it will enter into:
2. Press “ ” to type in the sequin mode (sequin mode 7), press to enter
the following:
3. Then type in other color changing positions and press to save. Press
to quit without saving.

11-4 Parameter instruction
1. R(L) sequin
The sequin device usually locates at the first or the last needle position (Note: for
dual sequin, the first and last needles are both sequin needles.) You can set “Yes”
or “No” to activate or shut the sequin embroidery.
2. Speed for Sequin R(L):
The speed depends on the sequin size. However, sewing the same sequin with
different mechanical structure, the acting angle could be different, which is
directly related to the maximum speed.
Note: the maximum speed of flat embroidery should be higher or equal to speed
for sequin embroidery.
the value and press to confirm.

3. R(L) sequin motor angle
It depends on sequin structure. This parameter has been properly set before
entering into market.
4. Auto start for sequin:
When the setting is “Yes”, system will start embroidering sequin automatically.
When the setting is “No”, machine needs manually start.
5. Time of Sequin Action:
This is to set the time period from sequin device goes down to embroidering (0-15,
the default value is 2). If the sequin device is controlled by valve, use the default

value; if it is controlled by motor, choose 4-5.
6. Sequin off after T.B
When the setting is “Yes”, sequin presser foot will be lift up automatically in case
of thread break. When the setting is “No”, the sequin device needs manually
lifting the presser foot.
11-5 Manual operation of sequin embroidery
It has two ways of operation, centralized operation and separated operation.
1. Centralized Operation
Centralized operation can be divided into three parts: “sequin start”, “sequin end”
and “Send sequin”.
(1) Press the key in the bottom of the screen and then select “sequin start”,
then press to let all the sequin presser feet go down.
(2) Press the key in the bottom of the screen and then select “sequin end”,
then press to let all the sequin presser feet go up.
(3) Press the key in the bottom of the screen and then select “send sequin”,
then press to let all the devices send out one sequin at the time you press the
key (sequin presser foot should be down at first).
2. Separated operation
Thread break switch is embroidery switch. When thread break switch is at the
down side, neither flat embroidery nor sequin embroidery is available.
Thread break warning lamp is mounted on the sequin sending device, which
offers the operator with easy view.

Note: when the manual valve control switch is in the middle, blue lamp is on,
which indicates a perfect condition of sequin embroidering.
Location of the switch board
11-6 Sequin testing
Press the key in the main screen, move the cursor to related machine test and
press . Then move the cursor to sequin device lift and down and press . Pull
bar towards right to lift the presser foot, while pull bar towards left to let presser
foot down. Then press to exit.

11-7 Sequin mending
After thread break or manually turning on the red lamp, pull bar and the machine
state is in sequin mending. All the sequin devices will lift up; machine stops when
it backs to the stop embroidering point. Pull bar again to let the sequin device (on
mending head) down for mending. When it reaches the stop point, machine stops,

then other sequin devices will be down to continue normal embroidery. “Patch
count” in machine parameter setting is ineffective in sequin mending.

Chapter 12 Directions on Coiling, Taping and Zigzag Embroidery
12-1 Function Introductions
1. Coiling function: This is a method to wind coiling thread(s) at an equal
interval around a core thread in a form of coil. Left Coiling (clockwise) and
Right Coiling (counterclockwise) are both available in coiling function,

which could be opted in computer parameters.
2. Taping function: Tape can be used as embroidery material. It includes
taping 1 and taping 2 (blind embroidery)

3. Zigzag function: Zigzag sewing lever swings to the right or left per stitch
in regard to the direction of original stitches. The upper thread forms Zigzag on
the embroidered material. There are six special stitches: Z1, Z2, Z3, Z4, Z5 and Z6.
Their stitches are as follows.
Z1 Z2 Z3 Z4 Z5 Z6
For convenience, Coiling, Taping and Zigzag-sewing are all called special
embroidery in the following.
4. Standard embroidery head and special embroidery head can be switched
automatically or manually.
5. Coiling, Taping and Zigzag functions can be switched at will.
6. The nipple of Special embroidery can be raised and lowered
automatically or manually. (Only for the machines installed with relevant

apparatus)
7. The highest speeds of Standard embroidery head and special embroidery
head can be set up respectively.
8. Auto saving of the stop-embroidery point of the M axis：The embroidery
work can continue from the stop-embroidery point when the power recovers.
9. The trimming function of the special embroidery head (no
trimming\trimming of the bottom thread\trimming of both the upper and bottom
threads)
10. The nipple of Special embroidery can be raised and lowered automatically
before manual frame shifting or embroidering.
11. Zigzag sewing lever can be tested manually.
12-2 Main Technical Details
1. The sequence of needle positions on Standard embroidery head and
special embroidery head: This control system default that the first one is special
embroidery needle position and Standard embroidery’s are from second to end.
2. Speed range of Special Embroidery: 300—600rpm, minimum of stepping
precision is 10r/m.
3. Angle of M-axis rotated manually: 18°/step.
12-3 Parameters and parameter setting
Press the parameter-setting key in the main screen to set relative
parameters for special embroidery. Press to shift page.

The remark of these parameters is as follows.
1. D28 Special Head Interval: 1~300.
Range: 0～300 Option: 150, 162, 166, 185, 200, 216, 225, 230, 240, 250, 270,
290, and 300
Select this parameter, input required value by typing in certain digit.
2. D30 Clamp Foot Displace: 0~90
Adjusting the working position of clamp foot: “0--90”; operation ditto. The height
is for every stitch.
3. D40 Adj Clamp Foot Limit: 0~250
The set value is added to the limit height of the clamp foot.
4. D31 Rod Pos. of ZIG: Left/ Right
The “ROD POS. OF ZIG” indicates that the position of swing when M axis is in
origin. Setting of this parameter must be kept in line with mechanical position.
5. C38 Swing Value of ZIG（-10.0～-0.2，+0.2～+10.0）
The parameter is for Z5 stitching function and applies to thick cords. For a thick
cord, the Z5 embroidering is to move the frame to add to the swinging scope of the

lever. The parameter’s absolute value is set according to the cord width. And the
“+/-” is decided by the machine structure. The moving directions of the lever and
frame should be the same. Otherwise please change the “+/-” setting.
6. D42 Rotary Gap of M Axis: 0~10
The M axis of special embroidery head has mill clearance. So without
compensation, the needle will not fall in the right position. Adjust this parameter
value to ensure that the needle falls in the center of tape.
During machine debugging, parameter value should be “0” when needle falls in
the center of tape. If not, repeat the adjustment to realize the best effect.
Generally, this parameter is managed by professional experts before leaving
factory.
7. D44 M Axis Work OFF Angle: 0, 90
In case of normal and sequin embroidery, the M axis stops at the angle of the set
value. When the distance between the normal embroidery head and special
embroidery head is small, this parameter must be set as 90° to avoid bumping.
8. D39 Z Shift Control Angle: 0~180
When the rotating angle is larger than the set value, the Z axis will wing faster.
9. D41 Adj Zig Rod Angle: 1~3
It is the starting angle of the rod, which indicates the relative position of the needle
bar and thread. It is used for embroidery quality. “1” means the swing starts at an
early angle; “2” means the swing postpones certain angle; “3” indicates the swing
postpones certain angle again to start.

10. C36 Ratio of Coil Emb.: The ratio of coiling: “1~4 Sti/L”
The parameter can change the coiling density; e.g. the set value 2 means one
coiling every two stitches.
12-4 Relative Operations of Special Embroidery
12.4.1 Shift between Lock Stitch Head and Special Head
1. Manual Shift
In the main screen, press the key to enter into color changing screen.
Press the key to change other special embroideries. Press to exit.

Definition of icons:
；
normal（lock-stitch） right coiling； left coiling；
taping 1； taping 2；
Z1 embroidery，Its feature is that the lever swings once every two
stitches.
Z2 embroidery，Its feature is that one lever swing every stitch and one
lever every two stitches take place alternately.

Z3 embroidery，Its feature is one lever swing every stitch.
Z4 embroidery，Its feature is one lever swing every stitch and its lever
swing direction is opposite to the one of Z3.
Z5 embroidery，Its feature is the same as Z4 and it’s desirable for the

embroidering of thick cords. (Refer to the parameter: the swinging scope of the
embroidery frame in Zigzag sewing)
Z6 embroidery，Its feature is three stitches at the same point and one

lever swing every stitch.
2. Automatic Shift
Before embroidering, automatic shift can be achieved through setting the color
changing position.
In the main screen, press the key , and then press the key and “1”
(special head) to change special embroidery pattern:
Press relative icon to select the pattern you need, if you don’t want to change, then
press to exit. After confirm of the pattern, system will display as:

Note: Icon“MANUAL”means that system go into manual shift state. It is used that
setting of manual shift still be in effect when system is in automatic shift

state.
During the embroidery process, it is common to shift between normal head and
special head. For instance, from special head to normal head, machine will
automatically stop at the finishing point; meanwhile, system will give the
following dialogue window. After tape operations are completed, users can pull
bar to close the window and shift the machine back to normal head to proceed
normal embroidering.
12.4.2 M Axis Operation of Taping Embroidery
This function is only for machines with taping embroidery function and includes
“M axis to be ready”, “M axis to cycle” and “M axis to turn”.

1. M axis to be ready
Press the key and click on the dialogue window to let the M axis back
to the working position, click to exit.

2. M axis to cycle
Press the key and click on the dialogue window to let the M axis rotate
to the “zero point”, click to exit.

3. M axis to turn
Press the key and click on the dialogue window to let the M axis rotate
to the left. It will rotate 18° left once you click the button. After 20 times click, it
will return to its origin; while click on the dialogue window to let the M axis
rotate to the right. It will rotate 18° right once you click the button. After 20 times
click, it will return to its origin; click to exit.

12.4.3 Operations of Clamp Foot
In the main screen, click to enter into the “Assistant Embroidery Operation”
screen, and move cursor to “Nipple up”,then press to lift the clamp foot,
select to exit.
Press the key and select“Nipple down”and to depress the clamp foot,
select to exit.
12-5 On Debugging Special Embroidery
Debugging special embroidery mainly includes Zigzag swing to its origin and up/
down of clamp foot. In the main screen, click to enter into “Other Assistant
Functions” screen, after that, click .

1. Sway Zigzag rod to 100
Move cursor to “Sway Zig Rod to 100” and click the key , after seeing the
dialogue window, pull bar to let all the swings act once. Click to exit. Users
can adjust swing angle by using this function.
2. Up/ down of Clamp Foot.
Move cursor to “Test lift clamp foot” and click the key , after seeing the
dialogue window, pull bar to let all the clamp feet up/down. Pull again to let them
down/up again. Click to exit.

12-6 Steps on Special Embroidery
1. Input design, carry out design selection, changing and editing according to
requirement.
2. Modify certain parameters, select color changing order and special embroidery
pattern.
3. Check special heads to make sure they are in perfect condition.
4. Pull bar to start embroidering.
12-7 Mechanical Category and Driving Mode Choice of Special
Embroidery Machines
Taping machines have three moving parts in the sense of mechanics. We define
them as M axis, E axis and clamp foot axis. M axis rotates a certain degrees every
stitch to trace the stitch, which ensures cords or tapes always in front of needle
movement. E axis swings once every one or two stitch to make the Zigzag
embroidery. Clamp foot axis is for lifting and lowering the clamp foot.

1. M axis
The mechanism of M axis can be divided to two types. One is with clutch
device, whose action is controlled by electric valve or by hand. Its advantage is
that only the M axis of the patching embroidery is moving and non-patching
embroidery heads are still when mending. This will help raise the quality and
efficiency of patching. The other type is without clutch device. Both of the two
types are driven by servomotor and the origin of the M axis is positioned by
proximity switch.
2. E axis
According to the difference in motor and whether to use the proximity switch
for positioning, E axis can be divided to the following types:
1) Stepping motor, driving heads separately, without proximity switch for
positioning
2) Stepping motor, driving heads by one motor, with proximity switch for
positioning
3) Stepping motor, driving heads by one motor, without proximity switch for
positioning
4) Servomotor driving, with proximity switch for positioning
3. Clamp foot axis
The working diagram of the clamp foot: (The clamp foot working height is the
interval of the foot’s movement with every stitch. The clamp foot rising height is
the foot’s moving distance from the bottom to the upper point in non-embroidery

mode. And it’s also called the clamp foot limited height.)
c T he clamp f oot u pper
The c lamp foot

b rising height
T he clamp foot
w orki ng height
a The clamp foot bottom
The clamp foo t
rising sketch map
According to the difference in motor and whether to use the proximity switch
for positioning, the clamp foot axis can be divided to the following types:
1） Raising the clamp foot manually
In this mode, the clamp foot working height relies on the rotating of the cam
and the clamp foot is raised to the limited height by hand.
2） 2-phase stepping motor, separately driving the embroidery heads, without
the holding force and proximity switch
It uses a 2-phase stepping motor for driving every special embroidery head
and controlling its working height and limited height. The power is off and there is
no the holding force when the clamp foot stays at the upper point or bottom point.
No proximity switch is taken for positioning. And the controller by default takes
that the foot is at the bottom position when turning on the machine.
3） 2-phase stepping motor, separately driving the embroidery heads, with the
holding force and without proximity switch
It uses a 2-phase stepping motor for driving every special embroidery head

and controlling its working height and limited height. The power is on and there is
the holding force when the clamp foot stays at the upper point, but not at the
bottom point. No proximity switch is taken for positioning. And the controller by
default takes that the foot is at the bottom position when turning on the machine.
4） Mono-phase AC motor, driving the embroidery heads by one motor, 2
proximity switches
and the clamp foot is raised to the limited height by one mono-phase AC motor
driving the clamp axis. Both the upper and bottom points are set with a proximity
switch to adjust the clamp foot rising height. Neither the upper nor bottom point
has the holding force.
5） (2-phase or 3-phase) stepping motor, driving the embroidery heads by one
motor, 1 proximity switch
and the clamp foot is raised to the limited height by stepping motor driving the
clamp axis. The upper point is set with a proximity switch to position. The bottom
point is set by parameters. Both the upper and bottom points have the holding
force.
6） Pneumatic motor, separately driving the embroidery heads, without
proximity switch.
and the clamp foot is raised to the limited height by pneumatic motor driving the

heads separately.
4. The composition chart for special embroidery machine controller
For different control systems, the E874 board takes different software programs
while the E874 board changes the DIP switches. Refer to 12-8.
12-8 Definition Charts of DIP Switches of E874 Boards
Chart 1:
DIP1 Composition Description of the M axis
OFF Manual clutch or without any clutch
ON Automatic clutch
Chart 2：
DIP2 DIP3 Composition Description of the E axis
ON ON Stepping motor, without proximity switch for positioning
ON OFF Stepping motor, with proximity switch for positioning
OFF ON Servomotor driving, with proximity switch for
positioning
OFF OFF No use

Chart 3：
DIP4 DIP5 DIP6 Composition Description of the clamp foot
ON ON ON Manual
ON ON OFF 2-phase stepping motor, separately driving the embroidery
heads, without the holding force and proximity switch
ON OFF ON Stepping motor, driving the embroidery heads by one motor,
with proximity switch
ON OFF OFF AC motor, driving the embroidery heads by one motor, 2
proximity switches
OFF ON ON Pneumatic motor driving
OFF ON OFF 2-phase stepping motor, separately driving the embroidery
heads, without the holding force and proximity switch

Appendix Ⅰ Parameter Setting List
**“Sti.” For stitches; “Emb.” For embroidery; “T. B.” for thread break; “N”
for the needle number of machine heads

Number Name Recom Range of Setting Note
mended
Value
Magnify, Rotate& Repeat Setting Parameters
A03 Direction P A03
A02 Rotate 0 0~89
A01 X&Y Scales 100/100 50%~200% Rotating angle of the
design
A06 Rep. Prior X Prior X prior, Y prior
A05 Rep. Mode Normal Normal, part Not used
A07 X&Y Reps 1/1 1~99
A08 X&Y Interval 0.0/0.0 -999.9~+999.9
A04 Prior Mode Rotate Rotate, scale
Embroidery Assistant Parameters
B01 Auto Origin Yes No, Yes
B02 To Do Cyclic No No, Yes Whether to
Emb. automatically repeat
embroidering the
design It often
accompanies repetition
or special punched
design.
B04 Display Yes No, Yes
Sti-Num or Not
C02 Sewing Empty No No, Yes If “Yes”, the machine
Stitch will omit the empty
stitches (needle moving
without embroidering).
If “No”, the empty
stitches won’t be
omitted.
B13 Start for Same Yes No, Yes Whether to start in
Colors color-changing way
when the later needle
position is same to the
former one


mended
Value
C04 Store Manual No No, Yes If “Yes”, manual color
Color changing is stored in
the color-changing
order. After
embroidery, the setting
will automatically
change into “No”.
D15 Slow STI. After 0 0~9999
Patch
D16 Speed After Max. 80~Max. Speed
Patch Speed
C03 Stop to Color No No, Yes Change stop codes into
color-changing codes.
It’s specialized for
some countries/regions.
B15 Emb Show Yes No, Yes
Background
B18 Is Design No No, Yes
TrueView
Display
C77 Do Filter Short No No, Yes It is fit for high-speed
Stitch machine using dahao
servo-motor driver
C78 Length of Filter 0.2mm 0.1~0.6 The same as above
Short Stitch
C79 Long Stitch Do No No, Yes The same as above
Auto Jump
C80 Stitch Len of 8.0mm 6.0~12.0 The same as above
Auto Jump
Thread break detecting Parameter
B05 T. B. Detect Yes No, Yes Thread break detect
B11 Sti. Not T.B. 0~15
Detect
B06 Stop machine Yes No, Yes
after T.B. detect
B07 Press key after No No, Yes Press key (pull bar)
T. B. after T. B.
B08 T. B. Back Sti. 0 0~7 It is unavailable to
some machine types.
B09 Patch Count 1 1~10 How many stitches to
patch before the thread


mended
Value
break point
B10 Speed Down Stop No Change, Down, Stop
After Patch
B14 To Set All No No, Yes If “Yes”, all unclosed
Heads Patch heads do patching
when patching.
B12 T. B. Detect No No, Yes
When Jump
C27 Detect T. B. spring spring，wheel, wheel 2
Mode
C28 STI. For Filter 3 1~6
T.B.
C67 Sensitivity of 6 1~15 When “Detect T.B.
Upper Thread Mode” is set “wheel
2”,the parameter is
available.
C68 Sensitivity of 6 1~15 The same as above.
Under Thread
C69 Filter Sti. For 6 Sti 1~6 Sti. The same as above.
Upper Thread
C70 Filter Sti. For 6 Sti 1~6 Sti. The same as above.
Under Thread
Frame Parameter
C06 Frame Curve F1 F1~F6 The high-speed
machine using dahao
servo-motor driver
hasn’t this parameter.
C06 Frame Angle 230 230~290
B03 Over frame by No No, Yes
Step
C15 High 16 0,1,2…30
Frame-Shift
Speed
C16 Low 12 0,1,2…30
Frame-Shift
Speed
D13 Speed When 16 0,1,2…30
Over frame
D19 (AFC) Use No No, Yes
D20 (AFC) Interval 3 0~15
Time


mended
Value
C74 X direction 245 230~280 It is fit for high-speed
Frame Angle A machine using dahao
servo-motor driver.
C75 X direction 245 230~280 The same as above.
Frame Angle B
C76 Y direction 245 230~280 The same as above.
Frame Angle A
C85 Y direction 245 230~280 The same as above.
Frame Angle B
C72 Machine hat Plain, hat, Clothes
Embroidery
Mode
C73 Frame Weight 1 0~20
Main shaft Parameter
C07 Max. Speed 700-850 250，300，350，…,1000
C09 Minimum 400 250,300,350…600
Speed
C08 Shift Stitch 3.0 1.0~10.0(common type When the stitch length
Length（mm） machine),3.0~6.0(high-speed is longer than the set
machine using dahao value, the machine will
servo-motor driver) lower the speed.
C10 Jump Stitch 500 400~750(common type Set the rotation speed
Speed machine),400~1100(high-spe for jump stitch.
ed machine using dahao
servo-motor driver)
C13 Set Run Speed 80 80,90…150
C12 Startup Stitches 1 1~9 Set the startup stitch
number.
D02 Startup Acce. 12 1,2,3…30 Increase the value to bring
a quicker speedup after
pulling the bar.
C25 Set Break Para. 0 0~30 When the main shaft
motor is an
electromagnetic motor,
the value is usually set
as 9. When it is a
servomotor, the
parameter is usually set
as 5-7.
C24 Main Motor 1 0~30 The parameter is
Para. invalid when it’s a


mended
Value
servomotor. When it’s
an electromagnetic
motor, increase this
parameter value to
avoid main shaft
vibration during
braking. Usually it’s set
as 1.
C14 Speed of Slow 400 80 (rpm)、the value of the
Emb. minimum speed
D14 Stop Ok bef. Yes No, Yes
Pull Bar
D10 Ratio of AC 0 -15% ~ +15% The parameter is used
Induction when the main shaft uses
induction motor. If the
value is incorrect, the set
rotation speed will be
different from the virtual
speed.
C05 Value for Thick 0 0~3
Cloth
C26 Para. Of Needle 15 0~30
Down
D53 Lock Shaft No No, Yes
When Stop
Thread-trimming Parameter
C01 Jump & Trim 3 Jump No Trim, 1Jump~7Jump
C18 Length of Trim 1 1~8 1 is the minimum
length and 8 are the
maximum length.
D05 Speed When 80 80,90,100…250
Trimming
C20 Lock Stitch. Yes No, Yes
When Trim
D04 Speed after 80 60,70,80…150 The parameter sets the
Trim rotation speed for lock
stitch.
C11 Stitches After 2 1~7
Trim
C21 Length of Lock 0.6 0.3~1.5
Sti.（mm）


mended
Value
C19 Lock Num. 2 0~3 Set the lock stitch
After Trim number when pulling
the bar for embroidery
after setting the
trimming.
D06 Spin Rounds for 1 1,2 2 for most machines, 1 for
Brake miniature type and
machines with servo
control main shaft motor.
C23 Action after Frame Y Frame X, Frame Y, Move
Trim Needle
C22 Frame after No No, Yes
Trim
D03 Set Hold 0 0~3
Startup Para.
D07 Check Trim is No No, Yes
OK
D08 Hook Angle by 0 -100~+100 Set the hook angle by
Motor motor. When the value is
increase, the hook angle is
moved backward.
D09 Hook Ratio by 2 1:9,1:10,1:12,1:15,1:18,1:20
Motor
C17 Turn Off No No, Yes
Trimming
D32 Is cutting Yes No, Yes
Machine
D48 Lock Stitch Len 0.7 0.3~2.0
Bef Trim
D49 Lock Stitch 2 0~2
Num Bef Trim
C81 Cutting start 3 0～20 It is fit for the machine
angle using step-motor for
trimming thread.
C82 Cut return angle 4 0～30 The same as above.
adj
C83 Cut keeper 5 0~99 The same as above.
return angle
C84 Hold voltage 1 1~3 The same as above.
adj
Sequin Parameter(D type)


mended
Value
C31 Speed for 400 300,310,…,the maximum
Sequin R speed
C32 Speed for 400 300,310,…, the maximum
Sequin L speed
D25 Sequin R Adj. 0 -15~15
Angle
D26 Sequin L Adj. 0 -15~15
Angle
C33 Auto Start for No No, Yes
Sequin
D27 Time of Sequin 3 0~15
Action
C34 Sequin Off after No No, Yes
T.B.
C56 Sequin Ind. No No, Yes
UpDown
B17 Up Valve When Yes No, Yes
Jump & Nocut
D54 Motor Number No,1~4,1(2~4) Set the parameter base on
of R Sequin sequin device. 2~4 mean
motor number by one
motor
D55 Set 3MM of R Lever 6~40 Degree, Roller
Sequin 6~40
D56 Set 4MM of R Roller 6~40 Degree, Lever
Sequin 6~40 Degree
Sequin 6~40 Degree
D58 Set 6.75MM of Roller 6~40 Degree, Lever
R Sequin 6~40 Degree
Sequin 6~40 Degree
C57 A Size&Color 3/4/5/6.75/9mm
of R Sequin Red/Green/Blue/Purple/Yellow/C
yan/silver/Golden
C58 B Size&Color 3/4/5/6.75/9mm
of R Sequin Red/Green/Blue/Purple/Yello
w/Cyan/silver/Golden
C59 C Size&Color 3/4/5/6.75/9mm


mended
Value
C60 D Size&Color 3/4/5/6.75/9mm
D60 Sequin Gap No No, 1,2
Num of R
Sequin
C65 Valve Time of 0 0~5
Right Sequin
D61 Motor Number No,1~4,1(2~4) Set the parameter base on
of L Sequin sequin device. 2~4 mean
motor number by one
motor
D62 Set 3MM of L Roller 6~40 Degree, Lever
Sequin 6~40 Degree
Sequin 6~40 Degree
Sequin 6~40 Degree
D65 Set 6.75MM of Roller 6~40 Degree, Lever
L Sequin 6~40 Degree
Sequin 6~40 Degree
C61 A Size&Color 3/4/5/6.75/9mm
of L Sequin Red/Green/Blue/Purple/Yello
C62 B Size&Color 3/4/5/6.75/9mm
C63 C Size&Color 3/4/5/6.75/9mm
C64 D Size&Color 3/4/5/6.75/9mm
D67 Sequin Gap No No, 1,2
Num of L
Sequin
C66 Valve Time of 0 0~5
Left Sequin
Sequin Parameter(J type)
D21 Sequin R No, Yes The first needle


mended
Value
On/Off position
D22 Sequin L No, Yes The highest needle
On/Off position
C31 Speed for 400 300,310,…,the maximum
Sequin R speed
C32 Speed for 400 300,310,…, the maximum
Sequin L speed
D25 Sequin R Adj. 0 -15~+15 Main shaft motor angle
Angle
D26 Sequin L Adj. 0 -15~+15
Angle
D23 R Sequin Motor Mutual：11.7,21.6,28.8,36, Sequin delivering
Angle 9,6.3,8.1,15.3,18,5.4, motor angle
12.6,16.2
Single：12,14.4,18,22.5
D24 L Sequin Motor Mutual：11.7,21.6,28.8,36,
Angle 9,6.3,8.1,15.3,18,5.4,
12.6,16.2
Single：12,14.4,18,22.5
C33 Auto Start for No No, Yes
Sequin
D27 Time of Sequin 3 0~15
Action
C34 Sequin Off after No No, Yes
T.B.
B17 Up Value When Yes No, Yes The same as above
Jump & Nocut
Special Embroidery Parameter
C55 M Axis Origin Yes No, Yes
At T.B.
C54 Cord Emb. Yes No, Yes
Needle
C37 M Axis Stop to Yes No, Yes
Origin
D28 Special Head 10 1~400 Destined Value: 150、
Interval 162、166、185、200、
216、225、230、240、
250、270、290、300
D30 Clamp Foot 0 0~90
Displace
D40 Adj Clamp Foot 170 0~250


mended
Value
Limit
B16 Clamp Foot 0 0~255
Min Height Adj
D31 Rod Pos. of Left Left/Right
Zigzag
D29 Zigzag Swing 90 0~90
Angle
C38 Swing Value of 0.2 -10.0~ -0.2,+0.2~+10
Zigzag
D50 Adj Z Emb 0 0~5
Swing
D42 Rotary Gap of 0 0~10
M Axis
D44 M Axis Work 0 0,90
OFF Angle
C39 Spec. Emb. Low Low, Above & Low, No Trim
Trim Mode
C35 Speed for 400 300~700
Sequin L
C51 Spec Minimum 250 250~400
Speed
C52 Spec. 30 1~180
Speed-Down
Angle
C53 Spec. 2 1~4
Speed-Down
Ratio
D39 Z Shift Control 0 0~180
Angle
D41 Adj Zigzag Rod 1 1,2,3
Angle
C36 Ratio of Coil 0 Sti/L 0~3 Sti/L
Emb.
D47 Slow Down Yes No, Yes
When Coil Emb
Machine &Maintenance Parameter
D01 Needles 1,2…MAXNEEDLE Set the value according to
the machine situation. E.g.
the value should be 9 for
9-needle machine. If the
value is different from the


mended
Value
machine needles, the color
changing will be abnormal.
C29 Needle of
No, 1, N
Boring
C30 Boring Emb. 0
0mm,12mm
Disp.
D17 Needle of Cord No No, 1, N
Emb.
D18 Speed for Cord 400 300,310,320…600
Emb.
D11 Adjust Head 0 0,1,2…30
Solenoid
D12 Color-Change 12 0,1,2…30 It’s valid only when the
Speed color-changing motor is
stepping motor. The
larger the value, the
faster the
color-changing speed.
D43 CloseBack 10 mins Never, 2mins, 5mins,
Light time 10mins, 15mins
C40 No Output No No, Yes It’s possible to change the
Design value after setting the
administrator password
and inputting the right
password.
C71 Adj. solenoid 6 1~10
Volt For Nipper
C41 Server Port It is used for setting
sever port when it is
connected to PC.
C42 MAC Address It is used for setting the
MAC address of
embroidery machine
network card. The
address is different as
different machine.
C43 IP Address It is used for setting
machine address when
connect to PC. It is not
different among
different machine.


mended
Value
C44 Server IP It is used for setting the
IP address of sever
when connect to PC.
C45 Subnet mask It is used for setting the
subnet mask of IP
address when connect
to PC.
C46 Gateway It is used for setting the
gateway of machine
when connect to PC.
D45 X Gap for Quilt 0.6 0~0.6
D46 Y Gap for Quilt 0.6 0~0.6
C47 Time for one 10sec
1～10
lubricating (sec)
C48 Stitches 10,000,0
100 ～ 1000 (unit
between two 00
10000stitches)
lubrications stitches
C49 X compensation 0.5
for mechanical -0.5~+0.5
gap
C50 Y compensation 0.5
for -0.5~+0.5
mechanical gap
D68 Machine Head 20
1~80
Num
E1 DIP1 3 0~255
E2 DIP2 3 0~255
E3 DIP3 3 0~255
E4 DIP4 3 0~255
Adj Parameters of X Servo Drivers(high-speed machine using dahao servo-motor driver)
Embroidery 300 93~650
Param
Frame-moving 260 93~650
Param 1
Frame-moving 13 6~50
Param 2
Parameter 1 30 10~50


mended
Value
Gear Blacklash 20 0~50
compensation
CMR 50 0~100
CMD 1 1~255
Adj Parameters of Y Servo Drivers(high-speed machine using dahao servo-motor driver, the
same as above)

Appendix Ⅱ Directions on USB operations
Appendix Ⅱ Directions on USB operations
No. Operation Direction Remark

1 Read & Write USB Same as floppy disk
2 Priority USB
3 Supporting format FAT16 and FAT32
4 Long filename Support but no display
For instance：“清
DOS 8.3 mode（8 digit
明上河图.DST”
5 Filename display prefix is viewable，suffix is
will be displayed as
3 digits）
“清明上~1.DST”
6 Filename displayed in Chinese support
7 Sub-directory operation support
8 Sub-directory limit No limitation
9 File account in one sub-directory 400
Back to disk management or
Reading & writing error/ change
10 design management screen,
USB
plug in the disk again.
Multi-logical disks in one
11 support
USB
12 Formatting USB support
13 Installing of the letter base Not support
14 Software update support
15 Special character in filename Support, except for “$”

Appendix Ⅲ Error Information
No. Mistakes
Upper monitor mistakes
01 Operation Fail
02 Operation Break
03 Machine Communication Error
06 Not set ZERO point
07 Fail to set ZERO point
08 No design start point
09 No software range
10 Password is wrong!
11 New passwords not same
12 Emb. design not existed!
13 Dest. design existed!
14 Design not existed!
15 Open design error!
16 Error type combined design
17 Open FLASH media error
18 Design has created!
19 No enough design mem.
20 Directory is invalid.
21 FLASH media write-protect
22 Design file not existed
23 Design name is invalid
24 Design file corrupt
25 Error read/write design
26 Not open design file
27 Error read FLASH media
28 Device not existed!
29 No floppy disk
30 Invalid disk type
31 Disk sector error
32 File not in disk
33 Not a file
34 File corrupt
35 disk write protect
36 Invalid directory
37 File existed!
38 Directory is full in memory.
39 Not enough space

No. Mistakes
40 Not open media
41 Error design data
42 Invalid design type
43 Not normal design
44 Not combined design
45 Please wait design operation
46 Cannot delete emb. design
47 Stitch number too large
48 Design stitches is over
49 Error design, or communication fail
51 Cannot delete a NULL memory
52 Read Design Error
53 Edit Forbid when Emb. Ready
54 Design is too big. Can't process.
55 Can not format the disk!
56 Unsupport operation!
Lower monitor mistakes
EC05 THE HOOK IS NOT OK
EC07 HOOKING TIME IS OUT
EC08 NOT SET (E. SET)
EC09 CANNOT RETURN
EC10 CANNOT RETURN
EC11 DESIGN NOT EXIST
EC12 STOP POSITION ERR
EC13 FRAME OVER LIMIT
EC14 CONTROL MEMORY LOST
EC16 STEP MOTOR ERR
EC17 CHANGE CLR OVERTIME
EC18 HALF RETURN ERR
EC19 NEEDLE POSTION ERR
EC20 MAIN MOTOR OVERTIME
EC21 CHANGE CLR OVERLIMIT
EC22 MAIN MOTOR REVERSE
EC23 CANNOT EMBROIDER
EC24 CANNOT FRAME BACK
EC26 CAN NOT TRIM
EC36 SEQUIN IS ON
EC37 PULL BAR ERROR
EC38 SPE. EMB. OVERTIME
EC41 FILE NOT EXIST
EC42 FILE DIRECTORY FULL
EC43 MEMORY SPACE FULL

No. Mistakes
EC44 FILE FAT ERR
EC45 FILE DIRECTORY ERR
EC46 HAS BAD SECTORS
EC95 Thread is broken, press key
EC101 Transfer CRC Error

Appendix Ⅳ Making of Special Multi-Sequin Design
1、 Dahao special multi-sequin design
The normal design making system identify a sequin code as a jump stitch, but
it can not distinguish sequin combinations from one stitch position. For instance,
it can not recognize it’s a sequin A or B at one stitch position. Dahao special
multi-sequin design making is to add a few jump stitch codes after the original
sequin code（jump stitch or stitch length is less than 0.1mm）to indicate sequin
combination. Thus achieve embroidering overlap sequin on one stitch position.
For instance, “A+C” means overlap sequin of A and C.
Rule is as follows:
The value of sequin A is 1，we use 1 sequin code.
The value of sequin B is 2，we use 1 sequin code plus 1 jump stitch.
The value of sequin A+B is 3，we use 1 sequin code plus 2 jump stitches.
The value of sequin C is 4，we use 1 sequin code plus 3 jump stitches.
The value of sequin A+C is 5，we use 1 sequin code plus 4 jump stitches.
The value of sequin B+C is 6，we use 1 sequin code plus 5 jump stitches.
The value of sequin A+B+C is 7，we use 1 sequin code plus 6 jump
stitches.
The value of sequin D is 8，we use 1 sequin code plus 7 jump stitches.
The value of sequin A+D is 9，we use 1 sequin code plus 8 jump stitches.
The value of sequin B+D is 10，we use 1 sequin code plus 9 jump stitches.

The value of sequin A+B+D is 11，we use 1 sequin code plus 10 jump
stitches.
The value of sequin C+D is 12，we use 1 sequin code plus 11 jump stitches.
The value of sequin A+C+D is 13，we use 1 sequin code plus 12 jump
stitches.
The value of sequin B+C+D is 14，we use 1 sequin code plus 13 jump
stitches.
The value of sequin A+B+C+D is 15，we use 1 sequin code plus 14 jump
stitches.
2、 Making trace for multi-sequin
By using trace, we can easily input sequin or sequin combinations. Example:
A, B, A+B, C, A+C, B+C, A+B+C, D, A+D, B+D, A+B+D, C+D, A+C+D,
B+C+D, A+B+C+D, etc.
We here take sequin B designing as an example.
1) Open any design making software. First we zoom in the blank to certain
scale（it is for easily input sequins in a place）and go into sequin state.
2) Input a sequin.

3) Since the value of sequin B is 2, we should put 2 sequins in here, which
means, we have to add another sequin.
4) Continue to type in other single-stitches.
5) You can see “stitch list” shows 2 sequins as the following image.
6) Select all stitches.

7) Making trace, group is JP, name is JP-B
8) Type in two reference point.
3、 Single needle multi-sequin, you can use “stitch form -> trace ->
apply”. Then “manual stitch” to finish entering.

4、 Others (curve）can apply trace too.
1) Click sequin button to enter “sequin state” (this is to ensure all the
curve course have sequin). Enter the curve as the following.

2) Select a target.
3) Set “target properties” and select related trace.

4) “multi-sequin” input is finished.
5、 Making alternate sequin
This is to realize embroidering of different sequin alternate. For instance,
A1B1 embroidery to realize embroidering A, B, A, B…
1) First you should design alternate trace. As the following A1B1
alternate design:

2) Apply the above trace to achieve alternate A1B1.
6、 Design maker should build up design data base
Now we have sequins: 3MM, 4MM, 5MM, 6.75MM and 9MM. while the
first needle position can have 4 sequin delivery devices at most. So we can
get the following 15 combinations: A,B,AB,C,AC,BC,ABC,D,AD,BD,
ABD,CD,ACD,BCD,ABCD.
The design data base emerges different sequin size with sequin
combination.
If there are two sequin delivery devices A and B. A design document
uses 3MM sequin and 5MM. Then the design data base should contain
3MM-A base, 5MM-B base, and 5MM-AB base. While the other design
data base uses 4MM and 6.75MM, then the design data base should contain
4MM-A, 6.75MM-B and 6.75MM-AB.
If there are three sequin delivery devices A, B and C. A design
document uses 3MM, 4MM and 6.75MM, then the design data base should
contain 3MM-A base, 4MM-B base, 4MM-AB base, 6.75MM-C base,

6.75MM-AC base, 6.75MM-BC base and 6.75MM-ABC base. While the
other design data base uses 3MM, 6.75MM and 9MM. Then the design data
base should contain 3MM-A base, 6.75MM-B base, 6.75MM-AB base, 9-C
base, 9-AC base, 9-BC base and 9-ABC base.
Other sequin design data bases are as the same
The alternate sequin design data base should combine single and
overlap sequins. For instance, 3MM-A sequin base and 4MM-AB sequin
base can form alternate sequin of 3MM-A & 4MM-AB, which achieves
embroidering effect of A, AB, A, AB…
7、 Normal sequin design to Dahao special sequin design
According to the above rules, we just need to insert some jump stitch
after “sequin code” to change the original sequin code to “multi-sequin
code”.
1) If you want to change the first sequin code to A+B sequin code, you
need to locate to that stitch first（its character is to let down the
sequin）.
2) Right click “insert jump stitch” twice to insert two jump stitches after
the original sequin code.
3) You can see the stitch list as the following image. The first sequin is
overlap A+B, the second one is sequin A.
Save as the TAJIMA DST document.

AppendixⅤ Network Connection of Embroidery Machines
Appendix Ⅴ Network Connection of Embroidery Machines
I、 Making Ethernet cable
1、 Making straight-through cable
The pins in the two terminals of twisted-pair cable have to be in one-to-one
correspondence. If the first pin of one terminal is green, the first pin of the other
terminal must also be green. The twisted-pair cable made in this way is usually
called “straight-through cable”.
Connection:
Pin 1 2 3 4 5 6 7 8
number
Pin orange orange green blue blue green brown brown
color white white white white
Shown in the following picture:
One terminal The other terminal
Usage: a. Link switch or HUB to router
b. Link computer (including server and workstation) to switch or HUB

2、 Making crossover cable
1－3, 2－6 crossover connection: Twisted-pair cable has 4 pairs of pins (8 pins).
Only 4 pins are used in network, namely the first, second and third, sixth pins.
They are used for receiving and sending signals. The connection rule is: the first
pin of one terminal is connected to the third pin of the other terminal, and the
second to the sixth. Other pins are connected to the corresponding pins. Cable
made in this way is called “crossover cable”.
Connection:
Pin number 1 2 3 4 5 6 7 8
corresponding 3 6 1 4 5 2 7 8
Pin number
Pin color white green white blue white orange white brown
green orange blue brown
Shown in the following picture:
One terminal The other terminal
Usage:
a. Connection between switches through UPLINKS interface

b. Connection between HUB and switch
c. Connection between HUB and HUB
d. Direct connection between 2 PCs (NIC to NIC)
e. Connection between interfaces of Routers
f. Connection between ADSL Modem (Ethernet interface) and NIC of PC
II、 Notes for network setting parameters
1、 MAC address
In physical transmission of network bottom level, the computers are
recognized by physical address (MAC). So it’s necessary to keep the uniqueness
of MAC address. When the first two digits of MAC address are not zero, some
network equipments regards it as illegal MAC address and the equipment can’t
be linked to the network. So the first two digits of MAC address must be zero.
2、 IP address
1) Definition of IP address
IP also called Internet address is the logic address for solely marking the
computers in internet. Every computer in the internet relies on the IP address to
mark itself. It’s like we find the phone by the phone number in the phone book. In
one network the IP address must be unique.
2) Form of IP address
One IP address includes 4 decimal integers portioned by decimal points.
Each integer is in fact composed of 8 binary numbers. So the maximum of each
integer is 255 and the minimum is 0.

3) Structure and classification of IP
The four numbers of IP address can be divided into 2 parts. One is network
number for marking the network. Another is computer number for marking the
specific machine in one network. IP addresses are divided into 3 kinds: A, B and
C.
A: the first number represents network and the following 3 numbers
represent computer.
B: the first two numbers represent network and the following 2 numbers
represent computer.
C: the first three numbers represent network and the last one represents
computer.
Use the following example to explain the network number and computer
number of C type.

Network Network number Computer number
1 192.168.1 .1
1 192.168.1 .2
1 192.168.1 .3
1 192.168.1 .4
2 192.168.2 .1
2 192.168.2 .2
2 192.168.2 .3
2 192.168.2 .4
3、 Subnet mask
To show how the network number and computer number are divided, subnet
mask is used to tell in one IP address which part is for network and which part is
for computer. It’s regulated that “1” is for network part and “0” is for computer
part. IP address and subnet mask combine to tell in which network the computer
is. So the subnet mask is very important. If it’s wrong, it will get the wrong
network address. Therefore the same network number must be set with the same
subnet mask.
4、 Gateway
it’s the IP address of the router which is in the same subnet of the computer. As
in the followed picture, if one data packet is to be transmitted to a computer in
network 2, this data packet has to be sent to the router linked to us. It’s like in

sending by post you only need to deliver a letter to postman instead of delivering
by yourself. So when the computers are not in the same network segment, the
gateway also has to be set properly in setting computers. Otherwise computers
don’t know where to deliver the data packet.
III、 The ways to construct network
1、 One PC directly connected to one embroidery machine
In this situation crossover cable is used to link the network interface of PC to
the network interface of embroidery machine.
PC
Crossover
cable
Embroidery machine
2、 C and embroidery machine linked by HUB
In this situation straight-through cable is used to link PC with HUB.

Embroidery Embroidery
PC PC machine machine
HUB
PC Embroidery Embroidery Embroidery

machine machine machine
3、 Connect the two networks in “2 ”through HUB
IV、 Setting the network parameters of embroidery machine
1、 MAC address of embroidery machine
Set MAC address of NIC of embroidery machine. Each embroidery machine
has its sole address. The range of this parameter is
000000000000~00FFFFFFFFFF.
2、 IP address of server
This parameter has to be the IP address of the PC installed with
EmbNetServer. This address can be found in the display window of
EmbNetServer.
EmbNetServer installation and use refer to the CD information with embroidery
machine.
3、 Server port No.
This parameter value is the port number used by EmbNetServer. The number
can be found in the display window of EmbNetServer.
4、 IP address of embroidery machine

Set the IP address of embroidery machine when it’s linked with PC. The IP
addresses of embroidery machines can’t be repeated. In one sub network the
network numbers of embroidery machines and PCs have to be the same. And
their computer numbers have to be different.
5、 Subnet mask
Set the subnet mask of IP address of embroidery machine when it’s linked
with PC. In one sub network the subnet masks of embroidery machines and PCs
have to be the same.
6、 Gateway address
If embroidery machines are in the two different sub networks, the gateway
address has to be set. Otherwise there’s no need to set it.

Computerized Embroidery Machine - Best Embroidery Machines (PDFDrive)

Uploaded by

Copyright:

Available Formats

Computerized Embroidery Machine - Best Embroidery Machines (PDFDrive)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Computerized Embroidery Machine - Best Embroidery Machines (PDFDrive)

Uploaded by

Copyright:

Available Formats

Version：2008-06

Certificate No. 06-018-03-094

QUALITY MANAGEMENT SYSTEM

This certificate is valid to the following product(s)/service:

BECS-C18 computerized embroidery machine owner’s manual I

4-17 Copy design with varied switch length......................................................................... 61

II BECS- C18 computerized embroidery machine owner’s manual

6.2.3 Power resume setting/ frame start setting.......................................................................... 93

BECS-C18 computerized embroidery machine owner’s manual III

10-7 Manual operation of sequin embroidery..................................................................... 140

IV BECS- C18 computerized embroidery machine owner’s manual

Chapter 1 General Descriptions

Thanks for using the Computerized Embroidery Control System of DAHAO

Company. It is appreciated that you do read this manual carefully in order to

manual for future use.

1-1 Warnings and Cautions

Don’t restore or operate in vibration, which may cause trouble to the

Notice Don't hold the cable when moving..

Overloading may cause serious loss. Please load according to the

BECS-C18 computerized embroidery machine owner’s manual 1

Notice Make sure the installation direction is correct..

Forbidding Don't test the insulation of the circuit loop.

Forbidding Never try to connect overloaded electronic device on the connector..

Notice Make sure the insulating of the cable is fine.

Notice Communicating cable and power cable should be separated.

Forbidding When machine is running, do not touch any running part.

Make sure the configuration of power supply in normal. Use stabilized

2 BECS- C18 computerized embroidery machine owner’s manual

If machine is inactive for a while, users must power on the machine

1-2 Main Features

everyday work into joyful experiences.

2. Shutdown of LCD Display

automatically in case of no operation in 10 minutes (the time can be changed in

3. Super-Large Memory Capacity

restored. Its super-large memory capacity can meet demands of different

4. Maximum One Million Stitches for 1 Design

and 250 times of automatic color changing.

5. Multi-Task Parallel and Free Shift among Tasks

BECS-C18 computerized embroidery machine owner’s manual 3

following designs and modification of parameters can be carried out. Flexible

shift among tasks can be realized by using the task-shifting key.

6. Storage of Frequently Used Parameters and Color-Changing Order for Each

it is one basis to realize network management.

7. Group Management of Parameters

groups of parameters can be restored, recovered and password-protected.

8. Input & Output Using USB

For each directory, system supports operation on 400 designs or sub-directory.

ZSK and FDR can be loaded.

9. Input of Several Design Files at One Time

10. Input design through network, color-changing order, etc.

4 BECS- C18 computerized embroidery machine owner’s manual

Network connector is available, which help user input design, color-changing

order, patch sewing, etc.

11. Network Function

LAN, which realizes network management, improve production efficiency and

enterprises to take the modern enterprise management. The explanation is

12. Patch Embroidery

and continue embroidering.

13. Break Adjusting