599-95 Step Mtrs Sel Gd.

out 11/15/00 1:44 PM Page 39

POWERMAX II®

All-in-one molded stator Integral electrical receptacle

Neodymium-iron-boron assembly provides high retention force of
rotor magnets mating connector—8 flying leads
Exposed laminations aid are standard option
thermal dissipation Rugged end bell, encapsulated
windings and electrical
connector utilize high-tech
polymer
Class B insulation
New end bell runs cooler;
encoder life is enhanced
Many drive shaft
modifications available
Optional encoders and
rear shaft extensions

Precision ground rotor

OD and honed stator ID for
concentric air gap
Largest available shaft diameter
(0.375") on a NEMA 23 stepper
Octagonal shape simplifies
withstands high radial and axial
automated assembly
loads, supports numerous shaft
modifications
• Available Sigmax® technology
Oversized 30mm bearings adds flux concentrating samarium
increase bearing fatigue cobalt stator magnets for highest
life (L10) 400% over typical torque and acceleration
NEMA Size 23 mounting 22mm bearings

MODEL NUMBER CODE POWERMAX II® motors

P 2 1 N R X A - L N N - N S - 0 0

Sequence Number
Insert 00 if all parts
Type are standard. Factory
P=Standard assigned if any parts
M=Enhanced Winding Type
are custom.
(n/a half stack) Construction A...per assigned letter
R=Regular S=Special
S=Special Encoder Option
Size NS=No Feedback
Rotor Type
2=NEMA 23 Use encoders below. You must specify
L=Standard
(2.25"across flats) shaft configuration D (double ended)
Termination J=Low inertia
X=Receptacle (n/a half stack)
F=8 Flying leads Caution: An encoder with line
Number of Stacks S=Special driver output may be
For X (receptacle) designation, required for use with some
H=Half stack Shaft Configuration step motor controls.
1=1 Stack mating leaded connectors may (Diameter & Length)
2=2 Stacks be ordered separately. N=Single M1=Encoder mounting provisions
Optional GRN/YEL ground wire D=Double HD=Encoder 500ppr
available. See p. 52 S=Special HJ=Encoder 512ppr
Mounting
SS=Special, call factory
N=NEMA
S=Special Shaft Modifications
N=Smooth
F=Flat
S=Special

The example model number above indicates a standard NEMA 23 frame motor with a one stack rotor. This motor is equipped with a standard
NEMA mount, regular construction, receptacle and an A winding. It also has a standard rotor, a smooth single-ended shaft and no encoder or
encoder mounting provisions.

HOW TO ORDER
Review the Motor Model Number Code to assure that all options are designated. Dimensions, connections and phasing diagrams start on
page 49. Encoder mounting options are on page 53.

www.pacsci.com 39
599-95 Step Mtrs Sel Gd.out 11/15/00 1:44 PM Page 38

POWERMAX II®

FEATURES BENEFITS
P OWERMAX II® sets the world
performance standard for NEMA 23
Two Year Warranty

New Polymer Encapsulated Stator

High quality, dependable operation

Exceptional thermal dissipation

step motors. At up to 253 oz-in.
New Polymer End Bell with Threaded End bell runs cooler, provides greater
holding torque, you won’t find a more Inserts flexibility in mounting encoder and brake
powerful two inch stepper. options
With POWERMAX II you also gain
the cost advantages of design for Largest Available Shaft Diameter on a Withstands high radial and axial loads.
NEMA 23 Stepper Supports numerous shaft modifications.
manufacturability (DFM) and North
America’s most advanced step motor Oversized 30mm Bearings Increases bearing fatigue life (L10), extends
manufacturing line. motor life, reduces downtime
That makes POWERMAX II
Sigmax® Technology Increases available torque
economical without sacrificing
features - such as long life bearings, Optional Low Inertia Rotor Produces the highest acceleration rate
high temperature insulation and possible
quality magnet materials.
Optional Solid Rotor High low speed torque, fast settling,
Plus DFM means we can build superior stiffness and damping
POWERMAX II to your specifications,
in the volumes you need, according Precision Ground Rotor OD and Honed High quality performance in an economical
to your JIT or other delivery Stator ID for Concentric Air Gap in an motor design.
Economical Motor Design
schedule.
Exposed Laminations Aids Thermal Improved heat dissipation extends
Standard Dissipation motor life, reduces downtime.

Standard POWERMAX II motors High Performance Gearheads Increases torque range in a reliable,
come in half, single and two stacks complete package
that provide holding torques from 42
to 253 oz-in.

Custom
POWERMAX II proves that an
economical step motor doesn’t have
to limit your options. It’s just the
opposite, thanks to flexible
manufacturing.
Whether you require a simple
drive shaft flat or an integral lead
screw, POWERMAX II motors are
made to order.

38 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 44

POWERMAX II® MOTOR TECHNOLOGY

Pacific Scientific developed POWERMAX II® to be the Does your application require that extra measure of
best cost/performance value available in hybrid step performance? Then consider the POWERMAX II M
motors. Series, featuring the patented Sigmax® technology.*
That’s why you’ll find so many standard Samarium cobalt magnets in M Series motors
POWERMAX II models in the universal NEMA 23 concentrate magnetic flux at desired points between
frame size. With POWERMAX II, you can tailor motor the rotor and stator. Sigmax technology optimizes flux
torque, acceleration and inertia to every axis of your paths to increase torque production and current
design. And you can do this economically too, using utilization over conventional hybrid designs.
a single mounting configuration and the driver of your
choice.

M SERIES ENHANCED HYBRID

P SERIES STANDARD HYBRID SIGMAX® TECHNOLOGY

S Stator Stator
S
S S
Non-torque Rare earth magnet
N N
producing flux inserts
Torque producing Focusing flux
flux Concentrated torque
Rotor producing flux
Rotor
N N

Typical paths of flux transfer Patented Sigmax®

in an energized conventional technology* redirects magnetic
hybrid step motor. Some flux flux to inhibit leakage and
leakage occurs in normal optimize torque production.
operation.
* Sigmax® technology is covered by U.S. patents
4,712,028, 4,713,470, 4,763,034 and 4,827,164.

TECHNICAL OVERVIEW
Types
POWERMAX II M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hybrid step motors with rare earth magnets
in the stator teeth
POWERMAX II P Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hybrid step motors

Rotor construction
POWERMAX II M and P Series;
with “L” rotor designates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Laminated
(high speed efficiency)
POWERMAX II M and P Series;
with “J” rotor designates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low mass/low inertia (fast start/stop,
high acceleration)

Windings
A, B, C, D, E, F, G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard winding to match any application
Phases ...................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Full steps per revolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Full step angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8°
Angular accuracy
POWERMAX II M and M “J” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1.5% of one step, no load,
non-cumulative
POWERMAX II P and P “J” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3% of one step, no load,
non-cumulative
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20 to 40°C
Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NEMA Class B, 130°C
Insulation resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Megohms @500V dc and 25°C
Shaft load ratings
Max. radial load (at center of std. shaft extension) . . . . . . . . . . . . . . . . . 20 lb.
Max. axial load (on front shaft extension toward motor) . . . . . . . . . . . . . 13 lb.

Bearing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Since large bearings (30 mm) are used,

life is typically about 4 times that of 22 mm
or smaller bearings used on other NEMA
Size 23 motors. POWERMAX II bearing fatigue
life (L10) exceeds 10,000 hours at any rotational
speed up to 10,000 full steps/second if
operated within the max. radial and axial
loads specified above.

Encoder options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See page 53.

44 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 45

POWERMAX II® HYBRIDS

NEMA 23 FRAME (2.3")—Ratings and Characteristics
Review the Model Number Code on page 39 to assure that all options are designated. Dimensions, connections and phasing diagrams are on
page 49. In addition to those below, motors with characteristics for specific performance requirements are offered. Contact factory for more details.

Connection Holding
Torque Phase
Rated Currents are in Rated Inductance
descending order Current/ Phase Thermal Rotor

Unipolar
Parallel
Motor (2 phases on) Phase Resistance Detent Resistance Inertia

Series
Model Number oz-in (Nm) (ohms) (mH) Torque oz-in-S2 Weight
±10% (amps DC) ±10% Typical oz-in (Nm) (oC/watt) (kgm2 x 10-3) lbs (kg)

Torque range: P2HNXXH-LXX-XX-00 • 59 (0.42) 5.2 0.22 0.5

42-61 oz-in. P2HNXXH-LXX-XX-00 • 59 (0.42) 2.6 0.90 1.9
.29-.43 Nm P2HNXXH-LXX-XX-00 • 42 (0.29) 3.68 0.44 0.5

STANDARD P2HNXXB-LXX-XX-00 • 59 (0.42) 2.6 0.76 1.9

P2H Series P2HNXXB-LXX-XX-00 • 59 (0.42) 1.3 3.04 7.6
1/2 rotor stack P2HNXXB-LXX-XX-00 • 42 (0.29) 1.84 1.52 1.9
2.5 6.6 0.0010 1.0
(0.018) (0.007) (0.45)
P2HNXXC-LXX-XX-00 • 61 (0.43) 2.5 0.84 2.3
P2HNXXC-LXX-XX-00 • 61 (0.43) 1.25 3.36 9.2
P2HNXXC-LXX-XX-00 • 43 (0.30) 1.77 1.68 2.3

P2HNXXF-LXX-XX-00 • 60 (0.42) 1.61 1.92 5.1

P2HNXXF-LXX-XX-00 • 60 (0.42) 0.80 7.68 20.4
P2HNXXF-LXX-XX-00 • 42 (0.30) 1.10 3.84 5.1

All ratings typical and at 25°C unless otherwise noted. Windings at 130°C and motor in still air at 40°C (without heat sink).
Operation of these motors above rated current may cause
An “X” in the Model Number Code indicates an undefined option. demagnetization. Contact factory.
Colored letter indicates winding. See Model Number Code on page
39. Small signal inductance as measured with impedance bridge at
1kHz, 1 amp.
See Model Number Code on page 39, optional leaded connectors
on page 52 and connection information on page 52. Thermal resistance measured with motor hanging in still air
(unmounted).
With rated current applied. Windings at 130°C and motor
unmounted and in still air at 40°C (without heat sink).

www.pacsci.com 45
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 46

POWERMAX II® HYBRIDS

NEMA 23 FRAME (2.3")—Ratings and Characteristics (Con’t)
Review the Model Number Code, page 39, to assure that all options are designated. Dimensions, connections
and phasing diagrams are on page 49. In addition to those below, motors with characteristics for specific
performance requirements are offered. Contact factory for more details.

Connection Holding
Torque Phase
Rated Currents are in Rated Inductance
descending order Current/ Phase Thermal Rotor

Unipolar
Parallel
Motor (2 phases on) Phase Resistance Detent Resistance Inertia

Series
Model Number oz-in (Nm) (ohms) (mH) Torque oz-in-S2 Weight
±10% (amps DC) ±10% Typical oz-in (Nm) (oC/watt) (kgm2 x 10-3) lbs (kg)

Torque range: M21NXXA-LXX-XX-00 • 142 (1.00) 5.6 0.23 0.7

95-144 oz-in. M21NXXA-LXX-XX-00 • 142 (1.00) 2.8 0.92 2.8
.67-1.02 Nm M21NXXA-LXX-XX-00 • 100 (0.71) 4.0 0.46 0.7

SIGMAX® M21NXXB-LXX-XX-00 • 137 (0.97) 4.6 0.32 1.0

M21 Series M21NXXB-LXX-XX-00 • 137 (0.97) 2.3 1.28 4.0
1 rotor stack M21NXXB-LXX-XX-00 • 97 (0.68) 3.3 0.64 1.0
9.4 5.5 0.0017 1.5
(0.066) (0.012) (0.68)
M21NXXC-LXX-XX-00 • 144 (1.02) 3.5 0.53 2.0
M21NXXC-LXX-XX-00 • 144 (1.02) 1.75 2.12 8.0
M21NXXC-LXX-XX-00 • 102 (0.72) 2.5 1.06 2.0

M21NXXD-LXX-XX-00 • 135 (0.95) 1.51 2.61 8.7

M21NXXD-LXX-XX-00 • 135 (0.95) 0.76 10.4 34.8
M21NXXD-LXX-XX-00 • 95 (0.67) 1.07 5.22 8.7

Torque range: P21NXXA-LXX-XX-00 • 114 (0.81) 5.6 0.23 0.8

77-116 oz-in. P21NXXA-LXX-XX-00 • 114 (0.81) 2.8 0.92 3.2
.54-.82 Nm P21NXXA-LXX-XX-00 • 81 (0.57) 4.0 0.46 0.8

STANDARD P21NXXB-LXX-XX-00 • 111 (0.79) 4.6 0.32 1.1

P21 Series P21NXXB-LXX-XX-00 • 111 (0.79) 2.3 1.28 4.4
1 rotor stack P21NXXB-LXX-XX-00 • 79 (0.55) 3.3 0.64 1.1 4 0.0017 1.5
5.5
(0.028) (0.012) (0.68)
P21NXXC-LXX-XX-00 • 116 (0.82) 3.5 0.53 2.3
P21NXXC-LXX-XX-00 • 116 (0.82) 1.75 2.12 9.2
P21NXXC-LXX-XX-00 • 82 (0.58) 2.5 1.06 2.3

P21NXXD-LXX-XX-00 • 109 (0.77) 1.51 2.61 10.3

P21NXXD-LXX-XX-00 • 109 (0.77) 0.76 10.4 41.2
P21NXXD-LXX-XX-00 • 77 (0.54) 1.07 5.22 10.3

All ratings typical and at 25°C unless otherwise noted. Windings at 130°C and motor in still air at 40°C (without heat sink).
Operation of these motors above rated current may cause
An “X” in the Model Number Code indicates an undefined demagnetization. Contact factory.
option. Colored letter indicates winding. See Model Number
Code on page 39. Small signal inductance as measured with impedance bridge at
1kHz, 1 amp.
See Model Number Code on page 39, optional leaded
connectors on page 52 and connection information on Thermal resistance measured with motor hanging in still air
page 52. (unmounted).
With rated current applied. Windings at 130°C and motor
unmounted and in still air at 40°C (without heat sink).

46 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 47

POWERMAX II® HYBRIDS

NEMA 23 FRAME (2.3")—Ratings and Characteristics (Con’t.)
Review the Model Number Code, page 39, to assure that all options are designated. Dimensions, connections and
phasing diagrams are on page 49. In addition to those below, motors with characteristics for specific performance
requirements are offered. Contact factory for more details.
Connection Holding
Torque Phase
Rated Currents are in Rated Inductance
descending order Current/ Phase Thermal Rotor

Unipolar
Parallel
Motor (2 phases on) Phase Resistance Detent Resistance Inertia

Series
Model Number oz-in (Nm) (ohms) (mH) Torque oz-in-S2 Weight
±10% (amps DC) ±10% Typical oz-in (Nm) (oC/watt) (kgm2 x 10-3) lbs (kg)

Torque range: M22NXXA-LXX-XX-00 • 230 (1.62) 6.5 0.21 0.7

161-253 oz-in. M22NXXA-LXX-XX-00 • 230 (1.62) 3.3 0.84 2.8
1.13-1.79 Nm M22NXXA-LXX-XX-00 • 163 (1.15) 4.6 0.42 0.7

SIGMAX® M22NXXB-LXX-XX-00 • 253 (1.79) 4.6 0.38 1.7

M22 Series M22NXXB-LXX-XX-00 • 253 (1.79) 2.3 1.52 6.8
2 rotor stack M22NXXB-LXX-XX-00 • 179 (1.26) 3.3 0.76 1.7

M22NXXC-LXX-XX-00 • 238 (1.68) 3.1 0.78 3.1

17 4.5 0.0036 2.5
M22NXXC-LXX-XX-00 • 238 (1.68) 1.55 3.12 12.4
(0.12) (0.025) (1.13)
M22NXXC-LXX-XX-00 • 168 (1.19) 2.2 1.56 3.1

M22NXXD-LXX-XX-00 • 238 (1.68) 2.5 1.22 5.0

M22NXXD-LXX-XX-00 • 238 (1.68) 1.25 4.88 20.0
M22NXXD-LXX-XX-00 • 168 (1.19) 1.77 2.44 5.0

M22NXXE-LXX-XX-00 • 227 (1.60) 1.64 2.71 10.1

M22NXXE-LXX-XX-00 • 227 (1.60) 0.82 10.8 40.4
M22NXXE-LXX-XX-00 • 161 (1.13) 1.16 5.42 10.1

Torque range: P22NXXA-LXX-XX-00 • 197 (1.39) 6.5 0.21 0.8

138-214 oz-in. P22NXXA-LXX-XX-00 • 197 (1.39) 3.3 0.84 3.2
.97-1.51 Nm P22NXXA-LXX-XX-00 • 139 (0.98) 4.6 0.42 0.8

STANDARD P22NXXB-LXX-XX-00 • 214 (1.51) 4.6 0.38 2.1

P22 Series P22NXXB-LXX-XX-00 • 214 (1.51) 2.3 1.52 8.4
2 rotor stack
P22NXXB-LXX-XX-00 • 151 (1.07) 3.3 0.76 2.1

P22NXXC-LXX-XX-00 • 203 (1.43) 3.1 0.78 3.9 7 0.0036 2.5

P22NXXC-LXX-XX-00 • 203 (1.43) 1.55 3.12 15.6 4.5
(0.049) (0.025) (1.13)
P22NXXC-LXX-XX-00 • 144 (1.01) 2.2 1.56 3.9

P22NXXD-LXX-XX-00 • 203 (1.43) 2.5 1.22 6.2

P22NXXD-LXX-XX-00 • 203 (1.43) 1.25 4.88 24.8
P22NXXD-LXX-XX-00 • 144 (1.01) 1.77 2.44 6.2

P22NXXE-LXX-XX-00 • 195 (1.38) 1.64 2.7 12.6

P22NXXE-LXX-XX-00 • 195 (1.38) 0.82 10.8 50.4
P22NXXE-LXX-XX-00 • 138 (0.97) 1.16 5.4 12.6

All ratings typical and at 25°C unless otherwise noted. Windings at 130°C and motor in still air at 40°C (without heat sink).
Operation of these motors above rated current may cause
An “X” in the Model Number Code indicates an undefined option. demagnetization. Contact factory.
Colored letter indicates winding. See Model Number Code on page 39.
Small signal inductance as measured with impedance bridge at
See Model Number Code on page 39 optional leaded connectors on 1kHz, 1 amp.
page 52 and connection information on page 52.
Thermal resistance measured with motor hanging in still air
With rated current applied. Windings at 130°C and motor unmounted (unmounted).
and in still air at 40°C (without heat sink).

www.pacsci.com 47
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 48

POWERMAX II®
HYBRIDS WITH LOW INERTIA
ROTORS

ROTOR INERTIA CHARACTERISTICS . . . POWERMAX II® motors

Single and double stack POWERMAX II motors are ACCELERATION COMPARISON
®

available with both standard and low inertia rotors.

Choose low inertia to produce the highest Theoretical
acceleration rates possible. Inertia Normalized
Model Rotor Type oz-in-S2 x 10-3/ Acceleration
kgm2 x 10-3 comparison
P21NRXX-L Standard 1.68/0.010 1

Single Stack
P21NRXX-J Low inertia 1.30/0.008 1.27
M21NRXX-L Standard 1.68/0.010 1.23
M21NRXX-J Low inertia 1.30/0.008 1.59
P22NRXX-L Standard 3.57/0.022 1

Double Stack
P22NRXX-J Low inertia 2.59/0.016 1.30
M22NRXX-L Standard 3.57/0.022 1.18
M22NRXX-J Low inertia 2.59/0.016 1.63

Low inertia rotors not offered for half stack models

Low inertia rotor Standard rotor Comparative values for normalized acceleration of unloaded motors. Base value is standard
hybrid motor with standard rotor, indicated for single and double stack lengths.
Actual acceleration capability depends on load, velocity profile and driver power.
Comparisons made with 90°C temperature rise using bipolar driver.

NEMA 23 FRAME (2.3")—Ratings and Characteristics

Review the Model Number Code, page 39, to assure that all options are designated. Dimensions, connections and phasing diagrams start on
page 49. In addition to those below, all 1 and 2 stack "L" construction windings, page 59, and custom windings for specific performance
requirements are available with low inertia rotors. Contact factory for more details.

Connection Holding
Torque Phase
Rated Inductance
Current/ Phase Thermal Rotor
Unipolar
Parallel

Motor (2 phases on) Phase Resistance Detent Resistance Inertia

Series

Model Number oz-in (Nm) (ohms) (mH) Torque oz-in-S2 Weight

±10% (amps DC) ±10% Typical oz-in (Nm) (oC/watt) (kgm2 x 10-3) lbs (kg)

Torque range:
99-140 oz-in.
.70-.99 Nm M21NXXA-JXX-XX-00 • 140 (0.99) 5.6 0.23 0.7
M21NXXA-JXX-XX-00 • 140 (0.99) 2.8 0.92 2.8 9.4
SIGMAX ®
M21NXXA-JXX-XX-00 • 99 (0.70) 4.0 0.46 0.7 (0.066)
M21 Series
1 rotor stack
0.0013 1.5
5.5 (0.009) (0.68)
Torque range:
79-111 oz-in. P21NXXA-JXX-XX-00 • 111 (0.78) 5.6 0.23 0.9
.55-.78 Nm 4
P21NXXA-JXX-XX-00 • 111 (0.78) 2.8 0.92 3.6
STANDARD P21NXXA-JXX-XX-00 • 79 (0.55) 4.0 0.46 0.9 (0.028)
P21Series
1 rotor stack

Torque range:
178-252 oz-in. M22NXXB-JXX-XX-00 • 252 (1.78) 4.6 0.38 1.5
1.26-1.78 Nm 17
M22NXXB-JXX-XX-00 • 252 (1.78) 2.3 1.52 6.0
SIGMAX® M22NXXB-JXX-XX-00 • 178 (1.26) 3.3 0.76 1.5 (0.12)
M22 Series
2 rotor stack
0.0026 2.5
4.5 (0.018) (1.13)
Torque range:
142-201 oz-in.
P22NXXB-JXX-XX-00 • 201 (1.42) 4.6 0.38 1.8
1.00-1.42 Nm 7
P22NXXB-JXX-XX-00 • 201 (1.42) 2.3 1.52 7.2
STANDARD P22NXXB-JXX-XX-00 • 142 (1.00) 3.3 0.76 1.8 (0.049)
P22 Series
2 rotor stack

All ratings typical and at 25°C unless otherwise noted. Windings at 130°C and motor in still air at 40°C (without heat sink).
Operation of these motors above rated current may cause
An “X” in the Model Number Code indicates an undefined option. Colored demagnetization. Contact factory
letter indicates winding. See Model Number Code on page 39.
Small signal inductance as measured with impedance bridge at
See Model Number Code on page 39, optional leaded connectors on page 1kHz, 1 amp.
52 and connection information on page 52.
Thermal resistance measured with motor hanging in still air
With rated current applied. Windings at 130°C and motor unmounted and in (unmounted).
still air at 40°C (without heat sink).

48 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 49

DIMENSIONS. . .(POWERMAX II ®
HYBRIDS) mm
in. (metric dim. for ref. only)

87654321

( 2.25)
(57,10)

(2X 1.85) .48 MAX. (12,19) WITH MATING

(46,99) 4X Ø .200 (5,080) THRU CONNECTOR PLUGGED IN
EQUALLY SPACED ON A
.99 MAX Ø 2.625 (66,670) B.C. .18 MAX. (4,57)
25,20 MOTOR ONLY

(2X 45°)

6,35 ± 0,000
+.0000 -0,013
.2500 –.0005
Ø Ø .2500 ± Ø 0,000
6,35 +0,000
–0,013 -.0005
.002 .002
0,051 (.20)
-A- 5,08
.055 (2.44)
1,400 (62,00)
38,1 ± 0,05
Ø 1.500 ± .002 .81 .75 ± .04
L MAX.
.003 A 20,60 19,1 ± 1,02
0,077
.003 A
0,077

Motor L STANDARD SHAFT OPTIONS ENCODER OPTION

Model Max. 1. Shaft modifications also available. See page 39. See page 53 for encoder/mounting specifications.
2. Optional flat available on front shaft as shown.
1.60
P2H 40,7 .50 USABLE
.219
2.06 5,56 12,7 FLAT
AGILENT
P or M21 52,3 TECHNOLOGIES
ENCODER
3.10
P or M22 78,7
Optional rear shaft extension available as shown. Same
diameter as front shaft extension.

(1.812)
.72 ø
(46,02)
18,29

CONNECTION INFORMATION . . .Terminations and phase sequencing

NOTE: Phase sequencing direction of rotation as viewed from mounting end of motor.
PHASE A

6
2 8 LEAD
5
1
DRIVER CONNECTION DRIVER CONNECTION
8 47 3
STEP A A B B STEP A B C D
PHASE B
1 1 GND O GND O
CCW CCW
A
2 A 2 O GND GND O
+V
3 A 3 O GND O GND
CW CW
B
4 4 GND O O GND

1 1 GND O GND O
B B C +V D
Bipolar full step 4-Lead connection 6-Lead connection Unipolar full step
(Bipolar) (Unipolar)
Notes:

0 = off or open
+ = positive current flow
- = negative current flow
GND = ground

www.pacsci.com 49
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 50

POWERMAX II® Flying Lead Motor Connection Informations

CONNECTION LEAD COLOR DRIVER

CONNECTION

4-LEAD BIPOLAR BLK A

BIPOLAR ORG A
SERIES RED B
YEL B
WHT/BLK & WHT/ORG —
WHT/RED & WHT/YE —
WHT/RED & WHT/YEL —

4-LEAD BIPOLAR BLK & WHT/ORG A

BIPOLAR ORG & WHT/BLK A
PARALLEL RED & WHT/YEL B
YEL & WHT/RED B

6-LEAD UNIPOLAR BLK A

UNIPOLAR ORG B
RED C
YEL D
WHT/BLK & WHT/ORG +V
WHT/RED & WHT/YEL +V

CONNECTION INFORMATION . . .Terminations and phase sequencing

NOTE: Phase sequencing direction of rotation as viewed from mounting end of motor.

DRIVER CONNECTION
STEP A B C D
A
Blk 1 GND O GND O
CCW
Wht/Blk
+V Wht/Org 2 O GND GND O
Org

B 3 O GND O GND
CW
Red Wht/ Wht/ Yel
Red Yel 4 GND O O GND

Blk O
1 GND O GND
PHASE A

Wht/Blk
Wht/Org 6-Lead connection Unipolar full step
Org
(Unipolar)

Red Wht/ Wht/ Yel

Red Yel

DRIVER CONNECTION
PHASE B
A A
8 lead motor
Blk Blk
STEP A A B B
(reference only
Wht/Blk Wht/Blk
1
Wht/Org Wht/Org CCW
Org Org
2
B A

Red Wht/ Wht/ Yel Red Yel 3

Red Yel CW
Wht/ Wht/
Red Yel
4

B B 1
SERIES PARALLEL
Bipolar full step
4-Lead motor
Notes: (Bipolar)

0 = off or open
+ = positive current flow
- = negative current flow
GND = ground

50 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 51

POWERMAX II® Flying Lead Motor

(57,10)
( 2.25)
(.25)
(2X 1.85) (6,35)
(46,99)

12.0 MIN
(304,8)

4X Ø .200 (5,080) THRU

EQUALLY SPACED ON A
Ø 2.625 (66,670) B.C.

1 (26,92)
(1.06)

(2X 45°)

6,35 + 0,000
+.0000 - 0,013
.2500 –.0005
Ø
Ø .2500 + 0,000
6,35 +0,000
–0,013 - .0005
.002
.002 (.20)
0,051
-A- 5,08 (2.44)
.055
(62,00)
1,400
38,1 ± 0,05
Ø 1.500 ± .002 .81 .75 ± .04
L MAX.
.003 A 20,60 19,10 ± 1,02
0,076
.003 A
0,076

Motor L
Model Max.
1.60
P2H 40,7
2.06
P or M21 52,4
3.10
P or M22 78,8

NOTES:
Flexible rubber boot may be bent as
shown. Normal height 1.0 inch (25,4)

www.pacsci.com 51
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 52

POWERMAX II®
CONNECTION
INFORMATION . . .
. . . Optional leaded connectors

Four different leaded connectors are available from

Pacific Scientific. Order the “GW” part number as a
separate item.

Connector/Leadwire
Part Phase Assembly Driver
Number Connection Pin No. Lead Colors Connection

bipolar 6 Black A
series 1 Orange A
8 Red B
3 Yellow B
2&5 Wht/Blk & Wht/Org none
4&7 Wht/Red & Wht/Yel none

bipolar 6 & 5 Blk & Wht/Org A

GW0000F parallel 1 & 2 Org & Wht/Blk A
(8 Lead) 8 & 7 Red & Wht/Yel B
3 & 4 Yel & Wht/Red B

unipolar 6 Black A
1 Orange B
8 Red C
3 Yellow D
2&5 Wht/Blk & Wht/Org +V
4&7 Wht/Red & Wht/Yel +V

unipolar 6 Black A
1 Orange B
GW0000E 8 Red C
(6 Lead) 3 Yellow D
2&5 Wht/Blk & Org +V
4&7 Wht/Red & Yel +V

bipolar 6 & 5 Black A

GW0000H parallel 1 & 2 Orange A
(4 Lead) 8 & 7 Red B
3 & 4 Yellow B

bipolar 6 Black A
GW0000L series 1 Orange A
(4 Lead) 8 Red B
3 Yellow B

Typical leaded connector (4-lead shown) Optional Ground Wire

+.00
.25 .06

#22 AWG,
PVC LEADS
+2.0
12.0 0.0

. . . Optional mating connector only NOTES:

GROUND LABEL PLACED IN

A separate mating connector housing and strain relief cover FRONT OF GROUND SCREW.
are available from Pacific Scientific or AMP. The GREEN/YELLOW SAFETY
EARTH CONDUCTOR (18AWG).
user attaches leads to the connector.

PACIFIC See page 39 for ordering information.

ITEM SCIENTIFIC AMP
STANDARD HOUSING GP00012 641653-8
STANDARD COVER GP00013 643077-8

52 www.pacsci.com
599-95 Step Mtrs Sel Gd.out 11/15/00 1:45 PM Page 53

ENCODER OPTIONS
NEMA 23 ENCODER OPTION
The standard encoder offered on the NEMA 23
motor is the Agilent Technologies HEDS 5600 series.

NON-LINE DRIVER ENCODER

2.05
Ø 1.812

ENCODER ENCODER OUTPUT

FOR CW DIRECTION OF ROTATION WHEN
VIEWED FROM MOTOR DRIVE SHAFT END.
(COMPLEMENTS NOT SHOWN) MIN. EDGE
SEPARATION 45°. INDEX GATED TO A AND B.
CHANNEL A
1.03
MAX. PIN CHANNEL B
12 345
INDEX (Z)
.44
Ø .108

18.0
MIN. 5X
LEADS 1

1.18

PIN COLOR FUNCTION

1 BLACK GROUND
2 BLUE Z
3 WHITE A
4 RED +5V
5 BROWN B

PARAMETERS NON-LINE DRIVER

TYPE INCREMENTAL
ENCODER OPTION HD HJ
PULSES PER REVOLUTION 500 512

SUPPLY VOLTAGE +5V ± 10% @ 85 mA MAX.

OUTPUT FORMAT DUAL CHANNEL QUADRATURE AND
INDEX

OUTPUT TYPE SQUARE WAVE TTL COMPATIBLE

FREQUENCY RESPONSE:
DATA 100 kHz
INDEX 100 kHz
ROTOR INERTIA 5 x 10-7 lb-in-S2
WEIGHT 0.08 lb.

ENCODER MOUNTING PROVISION ONLY = M1

FOR AGILENT TECHNOLOGIES HEDS 5600 SERIES OR SIMILAR.
2X 2-56 UNC-2B
.170 MIN. DEEP
EQUALLY SPACED
ON A Ø 1.812 B.C.

(Ø 1.1812)

+.0000
SHAFT DIA. .2500 - .0005
SHAFT LENGTH .75 ± .06

NOTES:
Leads are terminated with Agilent Technologies
HEDS-8903 connector.
TYPICAL @ 25° C

www.pacsci.com 53