PATTERN Our pattern is calculated for a height of 5’ 6” (168 cm).

If you
1 Center front piece 2x are taller or shorter, you may adjust the pattern to fit your
2 Side front piece 2x size. Choose your size at the lines marked "lengthen or
3 Center back piece 1x shorten here". Thus the proper fit is preserved. Make sure
4 Side back piece 2x that you adjust all pieces of one pattern by the same amount
5 Sleeve 2x at the same lines
6 Sleeve cuff 2x
7 Stand-up collar 2x How to lengthen and shorten pattern pieces:
8 Ruffle I 2x Cut the pattern pieces along the marked lines.
9 Ruffle II 2x To lengthen, slide the two halves of the pattern piece as far
10 Ruffle III 2x apart as necessary.
11 Loop 1x To shorten, overlap the two halves of the pattern piece as
12 Slit facing 2x far as necessary. Even out the side edges.

Paper cut for ANSI A (German DIN A4) prints: CUTTING OUT
The patterns are printed out on 25 sheets with a thin frame. FOLD (– – – –) means: here is the center of a pattern piece
Wait, until all sheets are printed out. Arrange the sheets so but never a cut edge or a seam. The piece should be cut
that they fit together (see extra page with the overview of the double, with the fold line forming the centre line. Pattern
prints). Cut off the single sheets on the upper and right edge pieces that are outlined with a broken line in the cutting
along the thin frame lines. Begin with the left lower sheet and diagrams are to be placed face down on the fabric. The
then glue the parts in the frame lines together precisely. cutting diagrams on the pattern sheet show how the pattern
Select your size according to the Burda-dimension table: pieces should be placed on the fabric.
Dresses, blouses, jackets and coats according to the bust
size, trousers and skirts according to the hip width. Change The cutting diagrams show the placement of the pattern
the pattern if necessary, to fit your measurements if they on the fabric
deviate from the Burda-dimension table. For a single layer of fabric, the pattern pieces are pinned to
the right side. For double layers of fabric, the right sides are
Size 4 to 14 (EU 36 to EU 46) facing and the pattern pieces are pinned to the left side. The
The button holes of piece 1 are marked according to size 2 pattern pieces that are shown in the cutting diagram,
(EU 34). For the bigger sizes mark the lowest buttonhole in extending over the fold of the fabric, should be cut last from
the same length to the waist sign like size 2 (EU 34). The a single layer of fabric.
upper buttonhole is positioned the same for all sizes. The
other buttonholes have to be distributed in equal lengths in SEAM AND HEMLINE ALLOWANCES are included on an
between the upper and the lowest button hole. average:
5/8” (1.5 cm) for all edges and stitches.
LENGTHENING OR SHORTENING THE PATTERN Using burda copying paper, transfer the lines and signs of
PIECES ACCORDING TO YOUR SIZE the pattern onto the left fabric side. You will find instructions
in the packaging.
Interfacing
Cut out the interfacing according to the drawing and press it onto
the left fabric side.

Sewing
While sewing the right fabric sides are facing. Transfer all
lines of the pattern onto the the right fabric side using basting
stitches.

Blouse
Front edges
1 Fold and press the front pieces along the fold line, and fold the
front pieces along the facing fold line to the outside. Stitch the
neckline edges on top of each other, starting from the front center
to the front edge. Secure seam ends. Cut in the allowances at the
front center, close to the stitch line (arrow 1a). Fold and pin the
facing to the inside, press and stitch narrowly (1b).

Back princess seams

Ruffle
3 Fold inside and press the allowances of the narrow ruffle edges
and the long ruffle edge. Stitch the edge, using a small and
narrowly adjusted zigzag stitches. Cut the overlapping
allowances close to the stitch line.

TIP: Test it using a piece of waste fabric. Use sewing machine

4 Ruffle III: Double stitch along the long edge, using large
stitches. Tighten the under threads to the length of the princess
seam, tighten from the top to the cross line. Knot the threads.
Distribute the width equally.

5 Baste the ruffle III onto the side front piece, starting from the
top to the cross line. The allowance of the shoulder seam is
overlapping (arrow).

Stitch the front princess seams according to the text and the
drawing no. 2 (seam 1), thereby enclosing the ruffle. Trim
allowances, neaten altogether and press inside the front center
piece.

Ruffle I and II: Trim the allowances of the rough edge to ¼” (0.5
cm) and neaten. Double stitch along the edge, ones 1/16” (2mm)
and another ¼” (7mm) from the edge according to the text and
drawing no. 4. Tighten the under threads of the ruffle to the
length of the front piece line where the ruffle will be applied. Knot
threads. Distribute the width equally.

6 Baste the ruffle II onto the side line of the front piece, the right
sides are facing, and stitch between the ruffle rows. Press the
ruffle towards the side edge. Stitch the edge narrowly (6a). Stitch
the ruffle II in the same way onto the front line.
Shoulder seams
Position the front piece onto the back piece, the right sides are
facing., baste shoulder seams (seam 3). The princess seams
meet. Neaten the allowances altogether and press inside the
back piece.

Stand-up collar
7 Press the allowances of the lower collar edge (collar without
interfacing) to the inside. Pin the collar pieces on top of each
other, the right sides are facing. Baste the edges according to the
drawing on top of each other, and stitch. Trim the allowances, cut
the corners bias. Turn the collar inside out. Baste edges, and
press.

8 Pin the collar into the neckline, the right sides are facing (seam
4), the cross lines meet the shoulder seams. Stitch. Trim
allowances, cut in the allowances and press inside the collar. Pin
the inner half of the collar onto the edge, and stitch narrowly.

Side seams
Position the front pieces onto the back piece, the right sides are
facing. Baste side seams (seam 5), and stitch. Trim allowances,
neaten altogether and press inside the back piece.

Loops
9 fold the straps lengthwise, the right fabric side inside. Stitch ½”
(1 cm) wide along the fold line. Trim allowances. Knot the
threads, thread the needle. Then move the needle (the needle
eye ahead (9a) through the strap opening (use a reel inside for
easy use). Cut the strap into two pieces. Neaten and fold the
ends inside.

10 Pin the loops onto the marked cross lines of the side seams,
and stitch narrowly.

Sleeves with cuff

12 Cut in the lower sleeve edge at the mark. Pull the cut edges
apart, then pin it onto the slit facing according to the drawing, and
stitch. Fold the facing over the edge and press.

13 Fold the half of the facing inside, and baste it along the edge
and stitch. Fold the slit in a way that the right sides are facing,
and stitch the facing at the slit end diagonally according to the
drawing (13a).

14 Fold the facing along the front slit edge inside. Press.
Fold the sleeves lengthwise, the right side inside. Stitch the
sleeve seams (seam 6). Neaten the allowances altogether and
press towards one side. Bunch the lower sleeve edge (according
to the text and drawing no. 11) to the width of the cuff.

15 Pin the sleeve cuffs onto the lower sleeve edge (seam 7), and
stitch. Press the allowances inside the cuff. Fold and press the
allowances of the other long edge.

16 Fold the cuff along the fold line, the right side inside. Stitch the
narrow sides on top of each other. Trim allowances, cut the
corners diagonally. Fold the cuff along the fold line inside, then
pin along the seam. Press. Stitch all edges narrowly on the right
fabric side, thereby stitching the inner half along the seam.

Apply sleeves
Bunch the sleeve rounding through slightly tightening the under
threads of the stitch lines.

17 Position the sleeves onto the armhole, the right sides are
facing. When you apply the sleeve 4 points are to be considered
for the “perfect fit”: The cross lines (8) of sleeves and front piece
have to meet. The sleeve seams and side seams have to meet.
The cross lines of the sleeve rounding have to meet the shoulder
seam. The width of the sleeve rounding has to be distributed
equally. Pin the sleeve from the side of the sleeve (not from the
side of the shoulder), and stitch. Trim allowances, neaten
altogether and press inside the sleeve.

Hemline
18 Fold the hemline to the inside and press, fold again and baste.
Stitch the seam narrowly.

Apply BUTTONHOLES onto the right front piece and the sleeve
cuffs. Sew the Buttons by hand.