OPERATING INSTRUCTIONS

SZ-7556-58-66-68-P
General Description Installation and Dimensions

The Sub-Zero Series SZ-75XX-P are aesthetically superior versions of 10mm

their predecessors. The SZ-7556/58/66/68-P are two relay controllers.

SZ-7556/58-P are specifically designed for the panel A/C,oil
cooler,package a/c and similar kind of applications.
The SZ-7558/68-P has an inbuilt power relay which can drive
compressive loads directly upto 20 Amps, thus eliminating the need of

70.5
34.5
a contactor esp. in single phase applications.
The controllers have special features like power on time delay for
alarms. Additionally these series offer several protection features that
are easily understood by the examples in the instructions below.
A number of parameters are displayed alphanumerically to set up the
instrument for each specific application.
To fix the unit, slide the fastener 1 through the guides 2 as per the position shown in
SZ-7556/58-P can be used for several applications with a measuring the figure. Move the fastener in the direction of the arrow, pressing tab 3 it permits to
range from 0OC to + 50OC, whereas SZ-7566-68-P can be used for move the fastener in the opposite direction of the arrow. Once the controller has been
connected, they should be covered with the lid 4 . Silicon sealant should be applied
several applications with a measuring range from -50OC to + 99OC. along the perimeter of the panel cut out or a rubber ‘O’ ring supplied before the unit is
fitted to increase protection against water seepage.
Controller: Controller should be installed in a place protected by vibration, water and
Technical Data corrosive gasses and where ambient temperature does not exceed the values specified
in the technical data.
Probe: To give a correct reading, the probe must be installed in a place protected from
Housing Black, ABS Plastic thermal influences, which may affect the temperature to be controlled.
Front Cover Red Polycarbonate plastic.
Dimensions Front : 75 X 34.5 MM Operating Messages And Icon Status
Depth : 71 MM (w/o back lid)
Panel Cutout 29 X 70.5 MM Message Mode Description Parameter
Mounting Flush panel mounting with fasteners.
H Flashing Temp. above the maximum limit of the set point. P2
Frontal protection IP 65 Flashing Temp. below the minimum limit of the set point. P3
Connections Screw terminal blocks. 2.5 sq mm one wire/ terminal Flashing Probe short circuit, circuit open or without probe,
only. or temperature>70OC or <0OC for SZ-7556/58-P
or temperature>99OC or <-50OC for
Display 2 X14.2 mm (0.56") LED. SZ-7566/68-P.
Data storage Non-volatile EEPROM memory. ON/OFF Comp. Relay on/off. SP, P4
Power input 230Vac +/-10%,50-60Hz. Others on request. Flashing Comp. Relay time delay active. P6
Operating temp. 5OC to 50OC (non-condensing).
ON/OFF Alarm Relay On/Off. AL,P7
Storage temp -20OC to 70OC (non-condensing).
ON/OFF Keypad locked/unlocked. LP
Input NTC Probe, SZ-N75
Resolution 1OC
Accuracy +/- 1OC Min = Minimum, Max = Maximum
Probe tolerance +/- 0.3O C at 25O C Fac. = Factory Setting (Default)
1. Set Point : To set the cut out point. Min Max Fac.
Front Panel View, Relay O
0C 50 C
O O
0C
1. Press and hold the “SET” key for 2 Seconds.
SZ-7556 /58-P
2. The set value will start flashing.
3. Use or prg to set the desired range. -50OC 99OC 0OC
SZ-7566 /68-P
4. Press key & you will see “- - -” which confirms
that the set point has been stored in memory.

Relay: 8(3)A/250Vac, Relay: 8(3)A/250Vac, Parameter List

Alarm: 5A/250Vac Alarm: 5A/250Vac
Range: 0OC to 50OC Range: -50OC to 99OC
2.To set other Parameters

1. Press & hold the prg key for 2 seconds.

prg 2. Display will show “P I “ for SZ-7566/68-P or
‘P2 ’ for SZ-7556/58-P & flash.
3. To go to other parameters, use or prg keys.

3. P I Parameter : To set controller for heating or cooling.

Relay: 20A/250Vac Relay: 20A/250Vac Min Max Fac.
Alarm: 5A/250Vac Alarm: 5A/250Vac (SZ-7566/68-P only.)
O O O O
Range: 0 C to 50 C Range: -50 C to 99 C
1. To change the P1 parameter, press the “SET” key. 0 1 0
2. To go to desired value, use or keys.
0 : Cooling mode.
I : Heating mode.
3. To set confirm value press “SET” key you will see
“- - -” which confirms that the value has been stored
in memory.

SZ-7556/58-P controller is by default set for cooling

mode.

SZ-7556-58-66-68-P 11-11-09 Page: 1/3

 OPERATING INSTRUCTIONS
4. P2 Parameter : To set maximum allowable high temperature to protect the life of the compressor when there are
Min Max Fac. power fluctuations and the compressor is switched off
limit & alarm.
and on within a few seconds.
1. To change the P2 parameter, press the “SET” key. XXOC 50OC 50OC
2. To go to desired value, use or keys. 9. P7 Parameter : To set power on time delay for alarm relay.
SZ-7556 /58-P Min Max Fac.
3. To set confirm value press “SET” key you will see O O O
“- - -” which confirms that the value has been stored XX C 99 C 99 C
This parameter sets a time delay on power on for the 0 Min 99 Min 0 Min
in memory. SZ-7566 /68-P
high & low temperature alarm.
Once set at a particular range, this will not allow the H 1. To change the P7 parameter, press the “SET” key.
set point to go above this range and below P3 setting. (Message on display) 2. To go to desired value, use or keys.
3. To set confirm value press “SET” key you will see ON
(Defrost in progress)
Example: Setting this parameter at 30OC will not allow “- - -” which confirms that the value has been stored
the set point to go above 30OC. Also, if the in memory.
temperature reaches 30OC, the display will show Ht
(High Temp.) indicating that the temperature has Example: If this parameter is set to 20min once the
reached or gone above the range in this parameter unit is powered on the alarm relay will not activate for
and at this point the alarm relay will activate. 20 minutes even if there is a fault. This is very useful
to eliminate the nuisance alarm when a unit is
5. P3 Parameter : To set minimum allowable low temperature switched on and the ambient is above the max set limit
Min Max Fac. in P2.This delay is applicable for High and Low
limit and alarm.
temperature alarms
1. To change the P3 parameter, press the “SET” key. 0 C XX C 0OC
O O

2. To go to desired value, use or keys. SZ-7556 /58-P

3. To set confirm value press “SET” key you will see 10. LP Parameter : To lock keypad.
“- - -” which confirms that the value has been stored -50OC XXOC -50OC Min Max Fac.
in memory. SZ-7566 /68-P
This parameter can lock the keypad so that tampering 0 1 0
Once set at a particular range, this will not allow the is not possible by by-standers.
set point to go below this range and above P2 setting. (Message on display) 1. To change the LP parameter, press the “SET” key.
O
2. To go to desired value, use or keys.
Example: Setting this parameter at 10 C will not allow
the set point to go below 10OC. Also, if the temperature 0 : keypad unlocked. ON/OFF
(Keypad lock)
reaches 10OC, the display will show Lt (Low Temp.) I : keypad locked.
indicating that the temperature has reached or gone
below the range in this parameter and at this point the 3. To set confirm value press “SET” key you will see
alarm relay will activate. “- - -” which confirms that the value has been stored
in memory.
6. P4 Parameter: To set the differential.
Min Max Fac.
When locked all parameters can only be viewed, but
1OC 20OC 2OC not modified.
1. To change the P4 parameter, press the “SET” key.
2. To go to desired value, use or keys. 11. AL Parameter : To activate alarm relay.
3. To set confirm value press “SET” key you will see Min Max Fac.
“- - -” which confirms that the value has been stored
in memory. Once set to on, the alarm relay will come on incase the 0 3 1
temperature reaches or goes above or below the
Differential between cut out and cut in temperature can points set in parameter P2 & P3 and if the probe fails.
be set between 1OC to 20OC.
1. To change the AL parameter, press the “SET” key.
Example: Cooling Mode: If the set point is set at 2. To go to desired value, use or keys. ON/OFF
(Alarm)
10OC and differential is set at 2OC, then when the
system reaches 10OC, the relay will cut out. Since the 0 : De-activates alarm relay.
differential is 2, the relay will cut in (restart) at 12OC I : Activate alarm relay on HT & LT.
(10OC+2OC). 2 : Activates alarm relay only on HT.
Heating Mode: If the set point is set at 10OC and 3 : Activates alarm relay only on LT.
differential is set at 2OC, then when the system
reaches 10OC, the relay will cut out. Since the 3. To set confirm value press “SET” key you will see
differential is 2, the relay will cut in (restart) at 8OC “- - -” which confirms that the value has been stored
(10OC-2OC). in memory.

7. P5 Parameter : To set probe calibration. This key will reset the alarm relay.
Min Max Fac.

In time it may be possible that the display may be -9OC 10OC 0OC 12. E I Parameter : To set relay status on Probe Failure.
Min Max Fac.
offset by a degree or so. To compensate for this error, SZ-7556 /58-P
you may need to add or minus the degrees required to
1. To change the E1 parameter, press the “SET” key. 0 2 1
achieve the correct temperature. -10OC 10OC 0OC
2. To go to desired value, use or keys.
SZ-7566 /68-P
1. To change the P5 parameter, press the “SET” key.
2. To go to desired value, use or keys. 0 : Comp.relay status is ON.
3. To set confirm value press “SET” key you will see I : Comp. Relay performs a duty cycle 10
“- - -” which confirms that the value has been stored minutes ON and 4 minutes OFF.
in memory. 2 : Relay status is OFF.

Example: The temperature on the display is 28OC, 3. To set confirm value press “SET” key you will see
“- - -” which confirms that the value has been stored
whereas the actual temperature is 30OC. You will need
in memory.
to set the P5 mode to 2, which means that once out of
the programming mode, the temperature will show
30OC (28OC + 2OC). 13. FS Parameter : To restore default settings of the controller.
Min Max Fac.
8. P6 Parameter : To set time delay between relay restart time.
Min Max Fac. When set to 1 all parameters are programmed to 0 1 0
factory values. Useful to debug setting related
This parameter is used to protect the compressor from 0 Min 99 Min 3 Min problems.
restarting in a short period of time and can be set
between 0 to 99 minutes. 1. To change the FS parameter, press the “SET” key.
2. To go to desired value, use or keys.
1. To change the P6 parameter, press the “SET” key. 3. To set confirm value press “SET” key you will see
2. To go to desired value, use or keys. “- - -” which confirms that the value has been stored
3. To set confirm value press “SET” key you will see Flashing in memory.
(Time delay in progress)
“- - -” which confirms that the value has been stored
in memory. 14. EP Parameter : To end programming.
Example: If this parameter is set at 3 minutes, the
relay will cut off at the set temperature, but will not Once the SET key is pressed, the control goes into the
restart for a minimum of 3 minutes, even if the normal mode and displays the temperature and all
differential is achieved earlier. This parameter is good settings are recorded.

SZ-7556-58-66-68-P 11-11-09 Page: 2/3

 OPERATING INSTRUCTIONS
Wiring Diagram Caution
WIRING: The probe and its corresponding wires should never be installed in a
SZ-7556/66-P conduit next to control or power supply lines. The electrical wiring should be
done as shown in the diagram. The power supply circuit should be connected
to a protection switch. The terminals admit wires of upto 2.5sq mm.
230V ALARM COMP.
NO C NC NO NC C WARNING: Improper wiring may cause irreparable damage and personal
1 3 5 6 7 8 9 10 11 12 injury. Kindly ensure that wiring is done by qualified personnel only.
PROBE
MAINTENANCE: Cleaning: Clean the surface of the controller with a soft
moist cloth. Do not use abrasive detergents, petrol, alcohol or solvents.

Compressor /Heater or
Contactor 8(3)A max
NOTICE: The information in this document is subject to change in order to
Alarm 5A max

To SZ-N75 improve reliability , design or function without prior notice and does not
represent a commitment on the part of the company. In no event will the
company be liable for direct, indirect, special, incidental or consequential
damage arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages. No part of this manual may
be reproduced or transmitted in any form or by any means without the prior
written permission of the company.

DISCLAIMER: This manual & its contents remain the sole property of
ACR Instruments & Valves Pvt. Ltd.,H.P., India and shall not be reproduced or
distributed without authorization. Although great care has been taken in the
preparation of this document, the company or its vendors in no event will be
liable for direct, indirect, special, incidental or consequential damage arising
out of the use or inability to use the product or documentation, even if advised
SZ-7558/68-P of the possibility of such damages. No part of this manual may be reproduced
or transmitted in any form or by any means without the prior written permission
of the company. ACR Instruments & Valves Pvt. Ltd.,H.P., reserves the right to
make and changes or improvements without prior notice.
ALARM 230V
COMPRESSOR C NO
WARRANTY: This product is warranted against defects in materials and
C NO 7 8 9 10 11 12 workmanship for a period of one year from the date of purchase. During the
PROBE warranty period, product determined by us to be defective in form or function
will be repaired or, at our option, replaced at no charge. This warranty does not
apply if the product has been damaged by accident, abuse, and misuse or as a
result of service or modification other than by the company. This warranty is in
To lieu of any other warranty expressed or implied. In no event shall the company
be held liable for incidental or consequential damages, including lost revenue
Compressor To SZ-N75
Alarm 5A max

or lost business opportunity arising from the purchase of this product.

20A max

SZ-7556-58-66-68-P 11-11-09 Page: 3/3