MTL5500 Range: Isolating Interface Units

Instruction manual
May 2017
MTL intrinsic safety solutions INM 5500 Rev 10
MTL5500 range
Isolating interface units
DECLARATION OF CONFORMITY
A printed version of the Declaration of Conformity has been provided separately within
the original shipment of goods. However, you can find a copy of the latest version at:
http://www.mtl-inst.com/certificates
ii INM 5500 Rev 10

CONTENTS
DECLARATION OF CONFORMITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II
IMPORTANT NOTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
ATEX SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VI
1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.1 Modules – pre-installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.2 Installing columns of isolators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.1 MTL5500 power bus - Installation and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2 MPA5500 AC power adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.3 Earth rail and tagging accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 DX ENCLOSURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1 Environmental conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3 Accessories in enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4 IS warning label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 UNIT DESCRIPTIONS, SETTING-UP AND CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6.1 Digital Input modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1.1 Phase reversal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1.2 Line-Fault Detection (LFD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1.3 MTL5501-SR - Fail-safe Switch/Proximity detector interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1.4 MTL5510 & MTL5510B - Switch/Proximity detector interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1.5 MTL5511 - Switch/Proximity detector interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.1.6 MTL5513 - Switch/Proximity detector interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.1.7 MTL5514/ MTL5514D/MTL5514-T - Switch/Proximity detector interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.1.8 MTL5516C - Switch/Proximity detector interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.1.9 MTL5517 - Switch/Proximity detector interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 Digital Output modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2.1 MTL5521/MTL5521-T - Solenoid Alarm driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2.2 MTL5522 - Solenoid Alarm driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2.4 MTL5523V/MTL5523VL - Solenoid Alarm driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.2.7 MTL5526 - Switch Operated Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.3 Pulse and Vibration modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
6.3.1 MTL5531 - Vibration Transducer Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.3.2 MTL5532 - Pulse Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.3.3 MTL5533 - Vibration Transducer Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.4 Analogue Input modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.4.1 MTL5541/MTL5541S/MTL5541S-T - Repeater Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.4.2 MTL5541A/MTL5541AS - Repeater Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.4.3 MTL5544/MTL5544S - Repeater Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.4.4 MTL5544A/MTL5544AS - Current Repeater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.4.5 MTL5544D - Repeater Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
(continued on next page)
INM 5500 Rev 10 iii

6.5 Analogue Output modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.5.1 MTL5546/MTL5546Y/MTL5546Y-T - Isolating Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.5.2 MTL5549/ MTL5549Y - Isolating Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.6 Fire and Smoke Interface modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.6.1 MTL5561 - Fire and Smoke Detector Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.7 Temperature Input module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.7.1 MTL5573 - Temperature Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.7.2 MTL5575 - Temperature Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.7.3 MTL5576-RTD - Temperature Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.7.4 MTL5576-THC - Temperature Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.7.5 MTL5581 - mV/Thermocouple Isolator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.7.6 MTL5582/MTL5582B - mV/Resistance Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.8 General modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.8.1 MTL5599 - Dummy Isolator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.8.2 MTL5991 - 24V dc power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.9 PCS45/PCL45USB configurator for MTL temperature converters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7 FAULT FINDING AND ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

7.1 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.2 Fault finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.3 Routine maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8 BENCH TESTING MODULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

8.1 Digital Input (DI) modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.2 Digital Output (DO) modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
8.3 Analogue Input (AI) Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
8.4 Analogue Output (AO) Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.5 Testing the functioning of other modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9 APPLICATIONS INVOLVING ZONE 2 AND/OR ZONE 22 HAZARDOUS AREAS. . . . . . . . . . . . . . . . 66

9.1 Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10 APPENDIX 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.1 MTL5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.2 MTL5018AC - Switch/proximity detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
10.3 MTL5051 serial data comms isolator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
10.4 MTL5314 trip amplifier for 2– or 3– wire transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
11 APPENDIX 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
11.1 Table A - Safety descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
11.2 Table B - Maximum cable parameters - IIC gas group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
11.3 Table C - Maximum cable parameters - IIB gas group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
© 2017 Eaton Electric Limited. All rights reserved.
iv INM 5500 Rev 10

IMPORTANT NOTE
WARNING
This manual has content describing the use and installation of safety
equipment. This equipment must be installed, operated and maintained
only by trained competent personnel and in accordance with all appropriate
international, national and local standard codes of practice and site
regulations for intrinsically safe apparatus and in accordance with the
instructions contained here.
ATEX
If the country of installation is governed by the Essential Health and Safety Requirements
(Annex II) of the EU Directive 2014/34/EU [the ATEX Directive - safety of apparatus] then
consult the ATEX safety instructions for safe use in this manual before installation.
Note: Refer to the website for multiple language safety instructions.
ELECTRICAL PARAMETERS
Refer to the certification documentation for the electrical rating of these products.
CERTIFICATION DOCUMENTATION
Our website http://www.mtl-inst.com contains product documentation regarding intrinsic
safety certification for many locations around the world. Consult this data for information
relevant to your local certifying authority.
FUNCTIONAL SAFETY
If the MTL5500 range of products are to be used in functional safety applications check that
each module has been assessed for that service and refer to the Safety Manual for details.
REPAIR
MTL5500 range of products MUST NOT be repaired. Faulty or damaged products must be
replaced with an equivalent certified product.
Symbols used on the product and in this manual
CAUTION - CAUTION -
Read the instructions Hot surface
INM 5500 Rev 10 v

ATEX SAFETY INSTRUCTIONS
The following information is in accordance with the Essential Health and Safety Requirements
(Annex II) of the EU Directive 2014/34/EU [the ATEX Directive - safety of apparatus] and is
provided for those locations where the ATEX Directive is applicable.
General
a) This equipment must only be installed, operated and maintained by competent personnel.
Such personnel shall have undergone training, which included instruction on the various
types of protection and installation practices, the relevant rules and regulations, and on the
general principles of area classification. Appropriate refresher training shall be given on a
regular basis. [See clause 4.2 of EN 60079-17].
b) This equipment has been designed to provide protection against all the relevant additional
hazards referred to in Annex II of the directive, such as those in clause 1.2.7.
c) This equipment has been designed to meet the requirements of EN 60079-15.
Installation
a) The installation must comply with the appropriate European, national and local regulations,
which may include reference to the IEC code of practice IEC 60079-14. In addition, particular
industries or end users may have specific requirements relating to the safety of their
installations and these requirements should also be met. For the majority of installations the
Directive 1999/92/EC [the ATEX Directive - safety of installations] is also applicable.
b) This apparatus is an associated electrical apparatus and is normally mounted in a non-
hazardous [safe] area. Specific apparatus described as Category 3 compliant may be
installed in a Zone 2 location providing that the relevant installation conditions are met. When
mounted in a Zone 2 location the apparatus must be provided with an enclosure, which
offers an additional degree of protection appropriate to the area classification.
c) Unless already protected by design, this equipment must be protected by a suitable
enclosure against:
i) mechanical and thermal stresses in excess of those noted in the certification
documentation and the product
specification
ii) aggressive substances, excessive dust, moisture and other contaminants.
Read also the Special Conditions for Safe Use (below) for any additional or more specific
information.
Special Conditions of Safe Use for Zone 2 applications

a) When used in Zone 2, the equipment must be installed in an enclosure or an
environment that provides a degree of protection of at least IP54 and meets
the relevant material and environmental requirements of EN 60079-0:2012
and EN 60079-15:2010.
b) The equipment must not be inserted or removed unless either:
i) the area in which the equipment is installed is known to be non-hazardous
or
ii) the circuit to which it is connected has been de-energised.
c) The 24V supply for this equipment must be derived from a regulated power
supply complying with the requirements of European Community Directives.
d) For 5511, 5514, 5514D, 5516C, 5517, 5526 & 5532 only: Relay contacts may
switch up to 35V, 2A and 100VA.
For 5575: Relay contacts may switch up to 35V, 250mA.
e) For 5573 Maximum Input/Output parameters – see certificate
vi INM 5500 Rev 10

Inspection and maintenance
a) Inspection and maintenance should be carried out in accordance with European, national
and local regulations which may refer to the IEC standard IEC 60079-17. In addition specific
industries or end users may have specific requirements which should also be met.
b) Access to the internal circuitry must not be made during operation.
Repair
a) This product cannot be repaired by the user and must be replaced with an equivalent certified
product.
Marking
Each device is marked in compliance with the Directive and CE marked with the Notified Body
Identification Number.
This information applies to MTL5500 products manufactured during or after the year 2015.
INM 5500 Rev 10 vii

This page is left intentionally blank
viii INM 5500 Rev 10

1 INTRODUCTION
This instruction manual describes the procedures for installing, connecting, checking and
maintaining MTL5500 range of isolating interfaces and accessories. The MTL5500 products provide
a DIN-rail mounted, intrinsically safe interface to hazardous areas of a process plant.
The individual sections of this manual cover the following topics
• Section 2 describes the range
• Section 3 specifies precautions both before and during installation
• Section 4 describes mounting accessories and the power adaptor
• Section 5 discusses the DX range of enclosures
• Section 6 provides relevant technical data
• Section 7 outlines fault-finding and maintenance procedures
• Section 8 describes bench test procedure
• Section 9 provides hazardous-area application information
• Section 10 provides MTL5000 products information
• Section 11 provides safety parameter information
2 DESCRIPTION
MTL5500 range of isolators provide intrinsically safe (IS) communication and signal conditioning
for a wide range of hazardous-area devices. Total AC and DC isolation exists between input,
output and power supply on separately powered units, and between input and output on
loop-powered units. No IS earth is required. DIN-rail mounting and plug-in signal and power
connectors simplify installation and maintenance. Units are powered from a 20 to 35V DC
supply, or, in some cases, from the signal itself.
Our latest generation of IS interfaces utilises an innovative “One-Core” technology to ensure

the highest quality and availability while maintaining maximum flexibility at lowest cost.
Incorporating advanced circuit design, a common set of components and innovative isolating
transformer construction, they achieve a significant reduction in power consumption while
increasing channel packing densities. The compact, 16mm wide design reduces weight and
gives exceptionally high packing density. They build on the proven success of the MTL2000,
3000, 4000 and 5000 ranges to bring the benefits of new developments in galvanic isolation
without compromising the reliability of the designs from which they have evolved.
The backplane mounting MTL4500 range is designed with system vendors in mind for “project-
focussed” applications such as Distributed Control System (DCS), Emergency Shutdown
Systems (ESD) and Fire and Gas monitoring (F&G).
The DIN-rail mounting MTL5500 range meets the needs of the IS interface market for
“application focussed” projects, ranging from single instrument loops, through to fully equipped
cabinets, across all industries where hazardous areas exist.
Both new ranges have been designed for compatibility with earlier models. The MTL4500 range
provides plug-replacements for earlier MTL4000 range of units, while the MTL5500 models
can easily replace MTL5000 range of units. Each offer the latest in modern technology and
efficiency without compromise.
In addition to their use in IS circuits, specific models within the MTL4500 and MTL5500
ranges have been assessed and approved for use in Functional Safety applications. These
have been verified under the certified Functional Safety Management (FSM) programme
implemented by us.
INM 5500 Rev 10 1

The table below lists the modules in the MTL5500 range. Refer also to the individual MTL5500
range of data sheets.
Digital Input Channels Function

MTL5501-SR 1 fail-safe, solid-state output + LFD alarm
MTL5510 4 switch/prox input, solid-state output
MTL5510B 4 multi-function, switch/prox input, solid-state output
MTL5511 1 switch/prox input, c/o relay output
MTL5513 2 switch/prox input, solid-state output
MTL5514/5514-T 1 switch/prox input, relay + LFD
MTL5514D 1 switch/prox input, dual relay output
MTL5516C 2 switch/prox input, relay + LFD outputs
MTL5517 2 switch/prox input, c/o relay + LFD outputs
Digital Output
MTL5521/5521-T 1 loop-powered solenoid driver
MTL5522 1 loop-powered solenoid driver, IIB
MTL5523 1 solenoid driver with LFD
MTL5523V 1 solenoid driver with LFD + voltage control, IIC
MTL5523VL 1 solenoid driver with LFD + voltage control, IIC
MTL5524 1 switch operated solenoid driver
MTL5525 1 switch operated solenoid driver, low power
MTL5526 2 switch operated relay
Pulse & Vibration Output
MTL5531 1 vibration probe interface
MTL5532 1 pulse isolator, digital or analogue output
MTL5533 2 vibration probe interface
Analogue Input
MTL5541 1 2/3 wire transmitter repeater
MTL5541A 1 transmitter repeater, passive input
MTL5541AS 1 transmitter repeater, passive input, current sink
MTL5541S/5541S-T 1 2/3 wire transmitter repeater, current sink
MTL5544 2 2/3 wire transmitter repeater
MTL5544A 2 transmitter repeater, passive input
MTL5544AS 2 transmitter repeater, passive input, current sink
MTL5544S 2 2/3 wire transmitter repeater, current sink
MTL5544D 1 2/3 wire transmitter repeater, dual output
Analogue Output
MTL5546 1 4-20mA smart isolating driver + LFD
MTL5546Y/5546Y-T 1 4-20mA smart isolating driver + oc LFD
MTL5549 2 4-20mA smart isolating driver + LFD
MTL5549Y 2 4-20mA smart isolating driver + oc LFD
Fire and Smoke
MTL5561 2 loop-powered for fire & smoke detectors
Temperature Input
MTL5573 1 temperature converter, THC or RTD
MTL5575 1 temperature converter, THC or RTD
MTL5576-RTD 2 temperature converter, RTD
MTL5576-THC 2 temperature converter, THC
MTL5581 1 mV/thermocouple isolator for low level signals
MTL5582/5582B 1 mV/resistance isolator to repeat RTD signals
General
MTL5599 1 dummy module
2 INM 5500 Rev 10

3 INSTALLATION
Important
• Make sure that all installation work is carried out in accordance with all relevant local
standards, codes of practice and site regulations.
• When planning the installation of MTL5500 range of isolators it is essential to make sure
that intrinsically safe and non-intrinsically safe wiring is segregated, and that units are
installed as required by a nationally accepted authority or as described in EN 60079-14, ISA
RP 12.6 or DIN VDE-165.
• External power supply shall contain double isolation from hazardous voltages or that unit
shall be supplied by Limited Power Circuit per UL/IEC 60950 or Limited Energy Circuit per
UL/IEC 61010 or Class ll Power Supply per NEC.
• Environmental conditions: indoor use, altitude (up to 2000m) and humidity less than 95%
non condensing.
• Check that the hazardous-area equipment complies with the descriptive system
document.
• If in doubt, refer to the certificate/catalogue for clarification of any aspects of intrinsic

safety or contact Eaton’s MTL product line or your local representative for assistance.
• Make sure the correct hazardous-area connector (field-wiring plug) is plugged into the
corresponding isolator. It is recommended that the connector is identified by the same tag
number as the matching isolator.
Optional TH5000 tag holder for individual

isolator identification.
Accepts tag label 25 x 12.5 ±0.5mm, 0.2mm thick
PWR
OP A
OPB
OPC
OPD
FLT
109.8
104.8 15.8 +/– 0.2
HAZ SAFE
118.8
123.6
Top of DIN rail
Figure 3.1: Dimensions of MTL5500 package
Mount all MTL5500 range of isolators on low-profile (7mm) or high-profile (15mm) type
T35 (top-hat) DIN-rail to EN50022, BS5584, DIN46277. This is available from Eaton, in
1 metre lengths (THR2 - DIN rail). Install isolators within the safe area unless they are
enclosed in approved flameproof, pressurised or purged enclosures and ensure that
the local environment is clean and free of dirt and dust. Note the ambient temperature
considerations of section 3.1.4.
It is recommended that, in normal practice, the DIN rail should be earthed/grounded

to ensure the safety of personnel in the event of a.c. mains (line) power being applied
accidentally to the rail.
INM 5500 Rev 10 3

3.1 Modules – pre-installation
3.1.1 Switch settings for operating conditions
Some modules have operating conditions, such as Line-Fault Detection (LFD), Phase Reversal,
etc., that can be established by the setting of switches on the unit. The subminiature switches
are accessible through an aperture on the side of the module (see Figure 3.2) and can be set in
the required positions with, for example, the blade of a small screwdriver.
The switch setting options are always indicated on the side label of the module, but the user may
also consult the individual module information in Section 6 of this manual for details.
1234
OFF position
ON position
Figure 3.2: Location of switches
3.1.2 Relay outputs

Reactive loads on all units with relays should be adequately suppressed. To achieve maximum
contact life on all mechanical output relays, the load should not be less than 50mW, e.g. 10mA at ≥
5V DC.
3.1.3 Ambient temperature considerations

Ambient temperature limits for unenclosed MTL5500 range of isolators are from –20°C to +60°C
with units close-packed and modules with the -T suffix have an extended temperature rating of
+65°C, unless otherwise specified.
3.2 Installing columns of isolators

On new installations, if isolators are mounted in several rows or columns, mount alternate rows or
columns so that units face in opposite directions. This allows safe- and hazardous-area wiring looms
to be shared. See Figure 3.1 for isolator dimensions.
3.2.1 Mounting isolators on DIN rail
Mounting
Removal
Figure 3.3: DIN rail mounting and removal of isolators
Clip an isolator onto the DIN rail as shown in Figure 3.3, with the blue signal plugs facing
towards the hazardous-area. To remove an isolator from the rail, insert a screwdriver blade
(2.5 - 5.0mm diam.) into the clip as shown. This will release the clip so that the isolator may
be pivoted off the rail - there is no need to lever the clip. Allow a maximum mounting pitch of
16.2mm for each unit.
4 INM 5500 Rev 10

3.2.2 Wiring up isolators
Each unit is supplied with the appropriate number and type of safe- and hazardous-area connectors
(see Figure 3.4), as dictated by the terminals used and the type of power supply.
with ferrule
Power Plugs
Grey: dc supplies (PWR5000)
12mm
trim
length
see table below
Signal Plugs
Grey: safe-area side
Blue: hazardous-area side
Figure 3.4: Removable power and signal plugs
Note: Earth Leakage Detection requires the use of hazardous area connector type HAZ1-3,
which may need to be ordered separately. See datasheet for ordering information.
Loop-powered devices do not require power connectors. Depending on the installation, it may
be easier to wire up isolators with power and signal plugs either in place or removed. Either
way, allow sufficient free cable to permit plugs to be removed easily for future maintenance
and/or replacement purposes. See Section 6 for instructions on wiring individual modules.
3.2.2.1 Signal and power conductors

Removable signal and power plugs are fitted with screw clamp terminals. Note that the
conductors should be between 14 and 24 AWG (1.6 and 0.5mm diam.) in size. Signal plugs,
located on top of the modules, are mechanically keyed to fit in only one position. They are
coloured grey, for safe-area connections, and blue, for hazardous-area connections.
For externally powered units, a power plug slots into the socket at terminals 13 and 14 on the
safe-area side of each module. The socket is coloured black if the unit is dc powered. Power
plugs are coloured grey, for plugging into the black sockets of dc powered units.
3.2.2.2 Making connections

a) Trim back the insulation of conductors by 12mm.
b) Check the terminal assignments shown in section 6 or on the side label of the unit.
c) Insert conductors according to the terminal assignments and tighten screws.
If the wires are to be fitted with crimp ferrules, the following is a list of those recommended with
required trim lengths for each:
Plug Entry Wire size Metal tube Trim Recommended ferrules

type (mm2) length (mm) length
Signal Single 0.75 12 14 Weidmuller 902591
Signal Single 1.0 12 14 Cembre PKC112
Phoenix Contact
Signal Single 1.0 12 14
AI 1-12 RD (3200674)
Signal Single 1.5 12 14 Cembre PKE1518†
Signal Single 2.5 12 14 Cembre PKE2518†
Power Twin 2x0.75 10 12 Cembre PKET7510
Power Twin 2x0.75 10 12 AMP (non-preferred) 966144-5
Power Twin 2x1.0 10 12 Phoenix Contact AI-TWIN 2X 1-10 RD
Power Single 0.75 10 12 AMP 966067-0
Power Single 1.0 10 12 Phoenix Contact AI 1-10 RD
TABLE 3.1: Crimp Ferule Options
† These ferrules with 18mm length metal tubes should be cut to 12mm after crimping
Note: Smaller section wire than that stated can often be successfully used if the crimping is good.
Crimp tool: Phoenix Contact Crimpfox UD6 part number 1204436
INM 5500 Rev 10 5

3.2.2.3 Finishing
Wire up individual isolators in accordance with wiring schedules. Daisy-chain power supply
connections between individual power plugs or use the power bus (see section 4.1).
Segregate hazardous- and safe-area wiring into separate trunking or looms wherever possible to
avoid errors and maintain a tidy installation.
Use an MTL5599 dummy isolator to provide termination and earthing for unused cores from the
hazardous area.
4 ACCESSORIES
4.1 MTL5500 power bus - Installation and use

4.1.1 MTL5500 range power bus
A power bus kit enables power supply terminals (13 and 14) of up to 32 installed MTL5500 range of
units to be linked to a standard 24V power supply. The bus consists of a chain of power plugs and
different lengths are available to suit various numbers of modules as follows.
Number of modules Kit ID code

(contains grey power plugs for 24V dc supply)
1 to 8 PB-8T
9 to 16 PB-16T
17 to 24 PB-24T
25 to 32 PB-32T
Table 4.1: Power bus kit options
4.1.2 Installation
1. Check to make sure the bus length is correct for the number of modules involved.
2. If the number of modules is less than the maximum number the chain will support, cut off
the surplus power plugs at the tail end of the chain - leaving sufficient cable to attach further
power plugs if it becomes necessary later.
3. Insert power plugs into the power terminals on the safe- area side of each module in sequence.
4. Connect the power supply source to the tail end of the chain (using the insulation displacement
connectors [Scotchloks] provided if required).
Notes:
1. To avoid excessive voltage drop or over-current, DO NOT connect power buses in .
2. Surplus sections can be used (and, if required) connected together provided the cut ends are
safely terminated and/or connected together. Use single ferrules with a crimp tool or insulation
displacement connectors (Scotchloks). Suitable ferrules and connectors are provided with the kits.
Figure 4.1: Power bus wiring, joining and terminating
– +
x2
Optional insulation
displacement
connectors
6 INM 5500 Rev 10

4.2 MPA5500 AC power adaptor
When only one or two MTL5500 modules are required for a particular application, it may be
desirable to power the units from the AC mains supply directly, rather than use a separate DC
supply unit. The MPA5500 is an adaptor that plugs into the DC power socket on the side edge
of an MTL5500 module and clips securely onto the module housing. Its 25V DC power output is
sufficient to supply a single module and can be connected to any normal ac power source.
AC inputs
15.8
133 20
118.8
11
Direction of Area required

Top of DIN rail removal of for removal of
MPA5500 MPA5500
Figure 4.2: MPA5500 AC power adaptor
To fit the adaptor, locate the tongue of the adaptor into the top slot on the side of the MTL5500
module and press the adaptor until it fits closely to the body of the module, as shown.
Use double-insulated AC power cable with conductor parameters of 0.2–1.5mm2, or 0.25–

1.5mm2 if using ferrules. Strip the outer insulation by no more than 30mm, then strip the inner
conductors by 8mm. Insert the cables appropriately in the cage-clamp connectors marked ‘L’
and ‘N’.
The incoming AC power must have some form of power disconnection device, such as a switch
or circuit breaker; a coupler that can be disconnected without the use of a tool; or a separable
plug, without a locking device, to mate with an adjacent socket outlet.
In addition, some form of cable anchorage must be used to relieve the cable conductors from
strain, including twisting, where they connect to the adaptor, and which will also protect the
insulation of the cable from abrasion.
WARNING
This adaptor is not suitable for use with MTL5000 range of modules.
INM 5500 Rev 10 7

4.3 Earth rail and tagging accessories
This section explains how to specify and assemble earth rail and tagging strip accessories for the
MTL5500 range.
The accessories consist of mounting brackets, earth rails, tagging strips and associated parts. They
provide facilities for earthing, terminating cable screens and tagging (identifying) the positions of
individual units.
4.3.1 Parts list
IMB57 Insulating mounting block (Figures 4.3, 4.4 & 4.5)

One required at each end of a tagging strip/earth rail. Suitable for low-profile (7.5mm) and high-
profile (15mm) symmetrical DIN rail.
ERB57S Earth-rail bracket, straight (figure 4.3, 4.4 & 4.9)

Nickel-plated bus bar; supplied with two push fasteners, one earth-rail clamp (14mm, 35mm2) and
one earth cable clamp (10mm, 16mm2).
Note: ERB57S is the preferred choice of earth-rail bracket. It is usually fitted in the upper slot on
insulating mounting block IMB57.
Where the earth rail is required to be positioned at a lower height and to allow access to the IMB57
mounting screws, the straight earth-rail bracket ERB57S can be inserted in the lower slot, but only
after insulating mounting blocks IMB57 are clamped to the DIN rail. This may not be possible if, for
example, trunking is fitted. In this case, fit offset earth-rail bracket ERB570 (see figure 4.4 & 4.10) in
the upper slot: the mounting blocks can then be fitted in a restricted space with this bracket already
fitted.
ERB570 Earth-rail bracket, offset (figure 4.9)

Nickel-plated bus bar; supplied with two push fasteners, one earth-rail clamp (14mm, 35mm2) and
one earth cable clamp (10mm, 16mm2).
ERL7 Earth rail, 1m length (figure 4.9)

Nickel-plated bus bar; may be cut to length.
TAG57 Tagging strip, 1m length (figure 4.3, 4.4 & 4.6)
Cut to size. Supplied with tagging strip label.
TGL57 Tagging strip labels, set of 10 x 0.5m (figure 4.3 & 4.4)
Spares replacement, for use with TAG57 tagging strip.
MS010 DIN rail module spacer, 10mm, pack of 5 (figure 4.7)

Grey spacer; Used to provide 10mm air-circulation space between modules, if necessary.
ETM7 Earth terminal, bag of 50 (figure 4.8)

For terminating cable screens and 0V returns on the ERL7 earth rail. For cables ≥ 4mm2.
TH5000 Tag holder

Spares replacement.
Connectors (Figure 4.5)

Spares replacement: HAZ1-3, HAZ4-6, HAZ-CJC, PWR5000, SAF7-9, SAF10-12 (SAF1-3 and SAF4-6
grey connectors, also available for use in safe-area applications).
4.3.2 Assembly
4.3.2.1 Fitting earth rails
a) In upper position
Before fitting insulating mounting blocks IMB57, check that the swing nuts in the base of
each unit are turned back into the moulding. Locate the mounting blocks on the DIN rail in the
chosen position and tighten the screws (see figure 4.10). Check that the swing nuts rotate
correctly to locate underneath the flanges of the DIN rail.
8 INM 5500 Rev 10

TGL57
THR2
TAG57
Snap off extension
when using IMB57 IMB57 PWR5000 ERB57S
as central support
ERB57
14mm 10mm Earth
Earth-rail clamp
clamp
ETM7 Push
ERL7 ERB57S
fastener
in upper
position
ERB570
ERB57S SAF10-12
in lower
position ERL7 SAF7-9
IMB57
ETM7 TH5000
HAZ1-3 TGL57
HAZ4-6
TAG57
Figure 4.3: Assembly drawing showing part numbers Figure 4.4: Mounting details

Figure 4.5: IMB57 Insulating mounting block

Figure 4.6: TAG57 Tagging strip, 1m length

Figure 4.7: MS010 DIN rail module spacers
Figure 4.9: Earth rails and clamps

Figure 4.8: ETM7 Earth terminals
INM 5500 Rev 10 9

Figure 4.10: Fitting IMB57
Slide a straight earth-rail bracket ERB57S into the upper slot in each mounting block. Push two
plastic push fasteners into each bracket to locate the brackets in the mounting blocks.
Cut earth rail ERL7 to the length needed. Slide the required number of ETM7 earth terminals
(5mm or 7mm wide) onto the rail. Clamp each end of the earth rail to earth-rail brackets ERB57S
using the terminal clamps (14mm, 35mm2) supplied. Fit an earth clamp (10mm, 16mm2) to the
free end of each earth-rail bracket.
Note: For lengths of earth-rail greater than 500mm, provide additional support by installing a
third IMB57 mounting block and earth-rail bracket, mid-way between the end mounting blocks.
Snap out the perforated extension between the lugs on this mounting block if a continuous
tagging strip is to be fitted (see figure 4.6).
b) In lower position, where at least 150mm clearance exists on one side, measured from the
edge of the mounting block.
As for a), but slide earth-rail brackets ERB57S into the lower slots in each mounting block.
c) In lower position, where there is insufficient clearance to fit earth-rail brackets ERB57S.
As for a), but slide offset earth-rail brackets ERB57O into the upper slot in each mounting
block before assembling the mounting blocks to the DIN rail. ERB57S brackets cannot be used
because they obscure the fixing screws on the mounting blocks.
4.3.2.2 Fitting tagging strips

Assemble mounting blocks IMB57 to the DIN rail as above. Cut TAG57 tagging strip and label to the
length needed, and insert label so that the appropriate side is visible. Clip the strip onto the lugs on
the mounting blocks. Hinge up the strip to provide access to the tops of the isolators.
Note: If necessary, provide additional support for long lengths of tagging strip by installing an
extra IMB57 mounting block mid-way between the end mounting blocks. Snap out the perforated
extension between the lugs on this mounting block.
4.3.3 Completed assemblies

Figure 4.11 illustrates a complete assembly of MTL5500 isolators using the accessories mentioned
above.
The broken-line boxes either side of the assembly represent cable trunking, and the accompanying
dimensions represent the recommended minimum spacing between the trunking and the module
assemblies.
10 INM 5500 Rev 10

Figure 4.11: MTL5500 complete assembly
Colour Module no. Function

Yellow MTL5501-SR
Digital Inputs
White MTL551x
Red MTL552x Digital Outputs
Blue MTL5531/33 Vibration
Purple MTL5532 Pulse
MTL5541x
Blue Analogue Inputs
MTL5544x
MTL5546x
Green Analogue Outputs
MTL5549x
Blue MTL556x Fire & Smoke
MTL557x
Orange Temperature inputs
MTL558x
Grey MTL5599 Dummy isolator
Table 4.2: MTL5500 front label colour coding
INM 5500 Rev 10 11

5 DX ENCLOSURES
Enclosures are usually selected on the basis of the number of units they will accommodate and
Table 5.1 shows the capacity of each of the enclosures. Figure 5.2 shows each type of enclosure
containing MTL5500 modules.
Table 5.1: DX range of enclosures - module capacities
Enclosure Number of MTL5500 isolators

16mm mounting pitch
DX070 4 (2*)
DX170 10 (8*)
(DX430) 26 (24*) no longer available
* Use these figures when two IMB57 mounting brackets for tagging/earth-rail accessories are included.
Note: The user should be aware that some workshop preparation may be required for the cable gland
plates before the enclosure is ready for on-site installation.
5.1 Environmental conditions

Environmental conditions that should be taken into account when installing DX enclosures include:-
See section
Maximum ambient temperature limits 5.1.1
Storage temperatures 5.1.2
Humidity 5.1.3
Corrosion resistance 5.1.4
Flammability 5.1.5
Impact resistance 5.1.6
Chemical resistance 5.1.7
5.1.1 Maximum outside enclosure temperature limits
Figure 5.1: Graph depicting outside enclosure temperature limits for DX enclosures used
with MTL5500 isolators
60 Enclosures
DX070
50 DX170
Max. outside enclosure
DX430
temperature (°C)
40
30
20
10
0
10 20 30 40
Power dissipation (watts)
The maximum outside enclosure temperature depends upon the total power dissipated by the
installed modules which, in turn, depends upon their number and type. It can also be influenced by
the Authority whose standards may need to be applied to the system, e.g. Baseefa, Factory Mutual
Research Corporation, Canadian Standards Association.
Figure 5.1 shows, in graphical form, the maximum outside enclosure temperatures (TMO) for given
levels of power dissipation.
The graph was derived from the following equation and should be used to calculate accurately the
suitability of any particular mix of modules.
TMO = 60°C - ∂T where ∂T = k1 x P
P = total power (watts) dissipated by modules in an enclosure

k1 = is a dissipation constant for a given enclosure and module . Select the relevant value from
Table 5.2.
(60°C is the temperature inside the enclosure)
12 INM 5500 Rev 10

Figure 5.3: Optimum orientation for wall mounted enclosure
DX070 DX170
MTL5500 4.03 1.88
Table 5.2: Dissipation constant k1 for enclosures (°C/watt)
Orientation of the enclosures is also important - the optimum position being on a vertical surface with
the internal DIN-rail horizontal as shown in Figure 5.3. Any other position can reduce the maximum
allowable ambient temperature by up to 5°C.
Examples
Tables 5.3 and 5.4 list likely combinations of MTL5500 modules in the three enclosure types and
indicate the acceptable maximum permitted outside enclosure temperature for these based on
the graph in Figure 5.1. See the specifications included in the datasheets for the power dissipation
figures of individual MTL5500 modules.
Table 5.3: Typical mix of MTL5500 modules
Enclosure Modules installed Power dissipation of modules Maximum outside

in watts (P) enclosure temp. (TMO)°C
DX070 2 x MTL5511 + 2 x MTL5544 (2 x 0.72) + (2 x 1.4) = 4.24 42.9
DX170 5 x MTL5511 + 5 x MTL5544 (5 x 0.72) + (5 x 1.4) = 10.6 40.1
Table 5.4: Power versus maximum outside enclosure temperature
Number of installed k Power dissipation Maximum outside

Enclosure modules °C/watt of modules in watts enclosure temp.
(P) (TMO) °C
4 4.03 4.0 43.9
DX070
4 4.03 6.0 35.8
10 1.88 10.0 41.2
DX170
10 1.88 15.0 31.8
5.1.2 Storage temperatures

Storage temperatures are safe within the range -40°C to +80°C.
5.1.3 Humidity limits

Safe humidity limits are within the range 5 to 95% RH.
5.1.4 Extended ambient temperature modules

Modules with the -T suffix are rated for use in an ambient temperature up to 65°C if suitably certifed.
INM 5500 Rev 10 13

130 Ø 5.2 131 (inside)
203.5
163.5
180
DX070
70
113.5 150
153.5
270
Ø 7.2
102
395
339
360
170
102
249
305
147 (inside) DX170

184
Top of DIN rail
540
80
270
305
249
n.b.
80
430
DX430
no longer
available
520 Ø 7.2
576
DX430
147 (inside)
184
Top of DIN rail
Figure 5.2: DX range of enclosures
14 INM 5500 Rev 10

5.1.5 Corrosion resistance
The effect of corrosion on DX enclosures is negligible.
5.1.6 Flammability rating

The flammable properties of the materials used in the construction of the enclosures are well
understood by manufacturers and ratings have been established to a number of standards. One of
the better known standards is the Underwriter's Laboratory standard UL 94 and the ratings for the
enclosure materials are given as:
Materials UL94 rating

Polycarbonate (all lids) V2/V0
Polycarbonate with glass reinforcement (DX070 base) V1/V0
Polyester with glass reinforcement (DX170 & DX430 bases) V0
Items made from similar materials are well established as suitable for use in process I/O marshalling
areas.
5.1.7 Impact resistance

The enclosure designs have been tested to an impact resistance of greater than 2 Joules which
exceeds the BS EN 61010-1 requirements of 0.5 Joules.
5.1.8 Chemical resistance

The overall chemical resistance of the enclosures is limited by the resistance of the transparent
polycarbonate lid. The glass-reinforced polycarbonate/polyester (GRP) bases have a higher resistance
than plain polycarbonate. Table 5.5 lists qualitative evaluations of resistance to a variety of chemical
agents.
Table 5.5: Qualitative evaluations of resistance to various chemical agents
Chemical agents Qualitative

evaluation
of resistance
Salt water; neutral salts; acids (low concentrations); hydraulic oil Excellent
Alcohols Very good
Acids (high concentrations); alkalis (low concentrations); petrol; cooling fluids Good
Alkalis (high concentrations); solvents. Poor
5.2 Mounting
5.2.1 General
These instructions are concerned solely with mounting the DX enclosures. Instructions for
wiring and testing individual modules within the enclosures are provided in Section 6.
Sufficient space is provided within the enclosures to accommodate tagging and earth-rail
accessories but this is at the expense of a reduction in the number of modules that can be
fitted.
5.2.2 Location and orientation

5.2.2.1 Location
The DX enclosures are intended for safe (non-hazardous) area use.
The enclosures are rated NEMA 4X; consequently, in N. America or Canada, assuming the
modules have the required approvals, they can be used in Class 1, Division 2 (gases) location,
but check with local requirements and ensure all cable entries also conform. In this case, an
additional warning label will be required on or near the enclosure warning that the MTL5500
interfaces must not be removed unless the area is known to be non-hazardous. The enclosures
are NOT suitable for Class II or III, Division 2 hazardous locations.
INM 5500 Rev 10 15

5.2.2.2 Orientation
As noted earlier (see section 5.1.1), for optimum temperature performance the enclosures
should be mounted on a vertical surface with the internal DIN rail horizontal.
5.2.3 Mounting details

See Figure 5.2 for the dimensions and mounting hole distances, etc., of the three DX enclosures.
The recommended method of mounting-described here-uses the four wall-mounting lugs supplied
with each enclosure. An alternative method of mounting is by direct attachment to the mounting
surface through the corner holes.
Note: When the wall-mounting lugs are used to attach the enclosures, the overall depth of the
enclosure is increased by an additional 3.3 mm (DX070) or 7 mm (DX170 and DX430).
a) At each of the four corner fixing holes, insert one of the screws provided and use it to attach
a fixing lug to the base of the enclosure.
b) Each lug can be used in one of two positions as shown in Figure 5.2.
c) Attach the lugs to the mounting surface with suitable fasteners.
d) Diameters of fixing holes in lugs are 5.5mm (DX070) and 7.0mm (DX170 and DX430)
e) Appropriate fixing hole distances are shown in Figures 5.2.
5.2.4 Cable glanding

All cables into the enclosures must be glanded to IP65 standards to maintain this rating for the
enclosure as a whole. Cable glands and gland plates are not supplied. Glanding requirements vary
for each enclosure as follows:
DX070
On the DX070, 'knockout' holes are provided, in two different sizes (15.5 mm and 21 mm), on the
side faces of the base. See Table 5.7 for recommended cable glands.
DX170
The DX170 can accommodate one gland plate on each side - see figure 5.2 for details. Table 5.6 lists
suppliers of suitable gland plate kits and Table 5.7 lists recommended glands.
Table 5.6: Recommended gland plate kits for the DX170 and DX430 enclosures.
Manufacturer’s part number

Manufacturer/agent Enclosure DX170
Hellermann Tyton TL-27/360
Sarel 21128
Table 5.7: Recommended cable glands for use with DX enclosures.
Gland Cable Gland plate Weidmuller part nos. Sarel part nos.
thread sizes hole size Gland Locknut Gland Locknut
size (mm) (mm)
PG9 5 to 8 15.2 951891 952216 08871 08881
PG13,5 8 to 13 20.4 951893 952218 08873 08883
Weidmuller (UK) http://www.weidmuller.co.uk
Sarel (UK) http://www.sarel.co.uk
Hellermann Tyton (UK) http://www.hellermantyton.co.uk
16 INM 5500 Rev 10

5.3 Accessories in enclosures
Apart from mounting, there are some other installation details which should be considered before
adding the appropriate interface modules and making the necessary cabling connections.
A range of accessories is available to accompany the MTL5500 units (see section 4) and the
following points should be observed.
5.3.1 Insulating mounting block (IMB57)

A pair of these can be attached to the DIN rail, at either end of the modules, to provide a mounting
for earth rails. Use of mounting blocks will reduce the space available for isolator modules.
5.3.2 Earth rails (ERL7)

Earth rail is produced in 1 metre lengths and will require cutting to length before mounting. ERL7
earth rails can be mounted either side of the modules but are typically mounted on the hazardous
side of the DIN rail.
5.3.3 Tagging strip (TAG57 and TGL57)

Tagging strip is produced in 1 metre lengths and will require cutting to length before mounting.
Similarly, the labels will require cutting to fit the tagging strip.
5.4 IS warning label

A 'Take Care' IS warning label is provided inside each enclosure. This should be attached to the inside
of the transparent lid when its orientation has been established.
INM 5500 Rev 10 17

6 UNIT DESCRIPTIONS, SETTING-UP AND CONNECTIONS
This section describes the function (briefly), the setting-up procedure and the wiring connections
for each MTL5500 unit. For a fuller functional description and a detailed technical specification,
refer to the individual datasheets, which can be found on our website at http://www.mtl-inst.com
or in the current MTL IS catalogue.
If a fault is suspected, first check that the power LED is lit (not applicable to loop-powered
devices). If necessary, check that all signal and power plugs are properly inserted, that no wires
are loose and that the unit is mounted correctly. If operation is still suspect, the unit should be
replaced with a serviceable unit.
There are no replaceable parts inside MTL5500 units, so any that appear to be inoperative should
be returned to the manufacturer/supplier for repair or replacement.
WARNING
When disconnecting units for maintenance purposes, take care to
segregate hazardous and safe-area cables.
• Short circuit hazardous-area cable cores to an IS earth or insulate and

secure the ends.
• Insulate and secure safe-area cables. If testing a unit ‘in situ’ note that
the test equipment used MUST be intrinsically safe.
The rest of this section is divided into sub-sections based upon the type of module, as follows.
6.1 Digital Input modules

MTL5501-SR, MTL5510, MTL5510B, MTL5511, MTL5513, MTL5514, MTL5514-T,
MTL5514D, MTL5516C, MTL5517
6.2 Digital Output modules
MTL5521, MTL5521 -T, MTL5522, MTL5523, MTL5523V, MTL5523VL, MTL5524,
MTL5525, MTL5526
6-3 Pulse and Vibration modules
MTL5531, MTL5532, MTL5533
6.4 Analogue Input modules
MTL5541, MTL5541A, MTL5541AS, MTL5541S, MTL5541S-T, MTL5544, MTL5544A,
MTL5544AS, MTL5544D, MTL5544S
6.5 Analogue Output modules
MTL5546, MTL5546Y, MTL5546Y-T, MTL5549, MTL5549Y
6.5 Fire and Smoke interface modules
MTL5561
6.7 Temperature Input modules
MTL5573, MTL5575, MTL5576-RTD, MTL5576-THC, MTL5581, MTL5582, MTL5582B
6.8 General modules
MTL5599, MTL5991
6.9 PCS45/PCL45USB configurator for MTL temperature converters
Note: Any LED indicator provided on the modules will display in the following colours:
LED label LED colour

PWR (power) Green
STS (status) Yellow
LFD (line fault) Red
FLT (fault) Red
OPx (o/p status) Yellow
18 INM 5500 Rev 10

6.1 Digital Input modules
The Digital Input (DI) module range offers solid state or relay output switches in a safe area that
respond to input switches located in a hazardous area. Single or multiple channel (2 or 4) options
are available, as well as Line-Fault Detection (LFD).
Modules with LFD can recognise open or short circuit conditions on the input wires going to the
field sensors, and some DI modules have the facility to reverse the effect of the input on the
output
i.e. phase reversal.
These options are chosen with switches located on the edge of the module on the hazardous
area terminal side. In some applications it may be easier to set these switches before fitting the
module to the DIN-rail.
1234
OFF position
ON position
MTL5513, MTL5516 - Ch 1 & 2

CH1 CH2 MTL5516C & MTL5517
PR LF PR LF
MTL5511 & MTL5514 - Ch 1 only
Figure 6.1: Switches to set LFD and phase reversal
6.1.1 Phase reversal

Set the PR switch ON or OFF for the appropriate channel(s).
6.1.2 Line-Fault Detection (LFD)

Where fitted, set the LF switch ON or OFF for the appropriate channel(s). Note: LFD is
permanently active on the MTL5501-SR.
For all DI modules with LFD except for the MTL5501-SR; when using the LFD facility with a contact
input, resistors must be used. Fit 500Ω to 1kΩ (preferred value 680Ω) in with the switch and 20kΩ
to 25kΩ (preferred value 22kΩ) in parallel with the switch.
For modes of operation of the MTL5510 & MTL5510B that include LFD, resistors should be fitted as
described above.
For MTL5501-SR use 1k4Ω in and 10kΩ in parallel with switch contact inputs.
For hazardous-area inputs conforming to EN 60947-5-6:2001 (NAMUR), a line fault is judged by

the following rules:
• Open circuit condition if hazardous-area current <50µA
• Line integrity (no open circuit) if hazardous-area current >250µA
• Short circuit condition if hazardous-area load <100Ω
• Line integrity (no short circuit) if hazardous-area load >360Ω
Note: the open circuit window (between 250µA and 50µA), and the short circuit window (between
100Ω and 360Ω), is not hysteresis. All MTL5500 modules, with inputs conforming to
EN 60947-5-6:2001 (NAMUR), will switch between open and complete circuit conditions within
these limits.
The MTL5501-SR LFD relay de-energises when a fault condition is detected. The MTL5514 and the
MTL5517 energise the LFD relay to indicate a fault condition.
INM 5500 Rev 10 19

6.1.3 MTL5501-SR - Fail-safe Switch/Proximity detector interface
Single channel, fail-safe module with line-fault detection
The MTL5501-SR enables a fail-safe switch/proximity detector located in the hazardous area
to control an isolated fail-safe electronic output. It provides line-fault detection (LFD) alarm
contacts and is designed for use with approved fail-safe sensors in loops that require operation
up to SIL3 according to the functional safety standard IEC 61508.
Note: For reliable, long-term operation the load on the LFD switching relay should be not less
than 50mW, e.g. 10mA at 5V DC.
Hazardous area Safe area
Resistors must –
always be fitted 6 7 + Failsafe
5 8 output
for switch inputs
4 9
1k4Ω
10
+ 3 LFD
2 11
10kΩ
– 1 12

13 Vs–
14 Vs+
20 to 35V dc

Figure 6.2: Terminal Function

Top label for 1 Input –ve
MTL5501-SR 2 Input +ve
7 Output –ve
8 Output +ve
10 LFD
11 LFD
13 Supply –ve
14 Supply +ve
Input / output characteristics

Input value in Fail–safe Operation LFD
sensor circuits output contacts
2.9mA < Is < 3.9mA ON Normal CLOSED
Is < 1.9mA & Is > 5.1mA OFF Normal CLOSED
Is < 50µA OFF Broken line OPEN
Rs < 100Ω OFF Shorted line OPEN
Correct operation of the fail-safe output and LFD is indicated by the LEDs on the front of the
unit. The yellow O/P LED is ON when the fail-safe output is energised. The red LFD LED flashes
if a line fault is detected. The fail-safe output is de-energised (OFF) if the module detects an
incorrect sensor current, an open circuit or a short circuit in the sensor circuit.
Input signal sensors may be either suitable proximity sensors or switches. The proximity sensor
properties are specified in the standard EN60947-5-6:2001; however, when used with
MTL5501-SR modules, additional requirements for the “low-impedance” current of 3.4
±0.5mA must be met. The list below shows suitable proximity sensors, all manufactured by
Pepperl+Fuchs Group, Germany, and specified as usable to SIL3, according to IEC 61508:
SJ 2-SN NJ 4-12GK-SN NJ 10-30GK-SN

SJ 3,5-SN NJ 5-18GK-SN NJ 15-30GK-SN
SJ 3,5-S1N NJ 8-18GK-SN NJ 6S1+U1+N
NJ 2-11-SN NJ 6-22-SN NJ 15S+U1+N
NJ 2-11-SN-G NJ 6-22-SN-G NJ 20S+U1+N
NJ 2-12GK-SN NJ 5-30GK-S1N NJ 40-FP-SN-P1
20 INM 5500 Rev 10

6.1.4 MTL5510 & MTL5510B - Switch/Proximity detector interface
4-channel, digital input and multifunction modules
These digital modules provide solid state output switches in a safe area that respond to switches
(inputs) located in a hazardous area. The way they respond - their “mode” - can be configured using a
bank of four DIL selector switches accessible through the side of the module - see Figure 6.4.
Model MTL5510 has an one output channel for each input channel and the user can reverse the
output phase if necessary to suit the application. Model MTL5510B has more varied modes that can,
for example, enable one input to affect multiple outputs or create latched outputs, etc.) The channel
output transistors - Ch1/Ch2 and Ch3/Ch4 - share a common terminal and can switch +ve or –ve
polarity signals.
Note that and parallel resistors are required for switch inputs with LFD - see Section 6.1.2 for
recommended values.

Ch D Outputs
– 4
6 7
+ 5 common
8
Ch C – 4 3
9
–
3 10 2
+ 2 11 common
Ch B
– 1 12 1
13 Vs–
Ch A Vs+
14

20 to 35V dc

Terminal Function

1 Input channel A
2 Input channel AB common (+)
3 Input channel B
4 Input channel C
Figure 6.3: 5 Input channel CD common (+)
Top labels for 6 Input channel D
MTL5510 7 Output channel 4
& MTL5510B 8 Output channel 3/4 common
9 Output channel 3
10 Output channel 2
11 Output channel 1/2 common
12 Output channel 1
13 Supply –ve
14 Supply +ve
INM 5500 Rev 10 21

Figure 6.4: DIL switches for setting mode
Tables 6.1 and 6.2 show details of the modes available and the switch settings required to obtain them.
For ease of access, it is recommended that switches are set to the required mode before installation.
Table 6.1 indicates whether the output follows the input, or the output is the reverse or antiphase of
the input.
For example, in mode 0, o/p 1 = chA; so, if channel A switch is closed, then output 1 will also be
closed or short circuit. However, in mode 1, o/p 1 = chA rev., so if channel A switch is closed, then
output 1 will be the reverse, i.e. open-circuit.
Table 6.1 - MTL5510 mode options

Switch setting
MODE o/p 1 o/p 2 o/p 3 o/p 4 i/p type
1 2 3 4
OFF OFF OFF OFF 0 chA chB chC chD
ON OFF OFF OFF 1 chA rev. chB chC chD
OFF ON OFF OFF 2 chA chB rev. chC chD
ON ON OFF OFF 3 chA chB chC rev. chD
switch
OFF OFF ON OFF 4 chA chB chC chD rev.
ON OFF ON OFF 5 chA rev. chB chC rev. chD
OFF ON ON OFF 6 chA chB rev. chC chD rev.
ON ON ON OFF 7 chA rev. chB rev. chC rev. chD rev.
OFF OFF OFF ON 8 chA chB chC chD
ON OFF OFF ON 9 chA rev. chB chC chD
OFF ON OFF ON 10 chA chB rev. chC chD
ON ON OFF ON 11 chA chB chC rev. chD prox.
detector
OFF OFF ON ON 12 chA chB chC chD rev. + LFD
ON OFF ON ON 13 chA rev. chB chC rev. chD
OFF ON ON ON 14 chA chB rev. chC chD rev.
ON ON ON ON 15 chA rev. chB rev. chC rev. chD rev.
Table 6.2 shows the MTL5510B modes. The logic tables and timing diagrams on the following
pages provide more detailed information on these modes.
Table 6.2 - MTL5510B mode options

Switch settings
MODE Function Equivalent
1 2 3 4
OFF OFF OFF OFF 0 4-ch switch input (see MTL5510 mode 0) MTL5510
ON OFF OFF OFF 1 2-ch each channel one input, two outputs
Same as mode 1 with all outputs phase
OFF ON OFF OFF 2*
reversed
ON ON OFF OFF 3 2-ch, 2-pole changeover output
OFF OFF ON OFF 4 1-ch with line fault output MTL5014
ON OFF ON OFF 5 As mode 4 with changeover outputs
OFF ON ON OFF 6 1-ch with start-stop latch MTL2210B
ON ON ON OFF 7* As mode 2 with LFD enabled
OFF OFF OFF ON 8 4-ch switch input, see MTL5510 mode 8 MTL5510
ON OFF OFF ON 9 2-ch with line fault output MTL5017
OFF ON OFF ON 10 As mode 9 with LFD changeover
ON ON OFF ON 11 As mode 10 with channel phase reversed
OFF OFF ON ON 12 3-ch with normally-open LFD output
ON OFF ON ON 13 3-ch with normally-closed LFD output
OFF ON ON ON 14 2-ch monostable, pulse stretcher
ON ON ON ON 15 4-ch switch input, see MTL5510 mode 15 MTL5510
*Mode of operation changed August 2015
MTL5510 & MTL5510B diagnostics

If an internal fault is detected, all outputs and channel LEDs will turn off and the red Fault LED
will turn ON.
22 INM 5500 Rev 10

MTL5510B modes
The following logic and timing diagrams are provided to assist the user in understanding the behaviour of the MTL5510B module
when a specific mode is chosen.
The open switch ( ) and closed switch ( ) symbols are used to represent both the input conditions of Ch A, Ch B, Ch C or Ch
D and then the output conditions of o/p 1, 2, 3 or 4. Note that in certain modes a Line Fault can cause an override of the output.
Mode 1: 2 ch, each ch 1 input 2 outputs How to use these mode tables - examples
i/p - Ch A i/p - Ch C The logic tables for Mode 1 represent Ch A controlling outputs 1
& 3, while Ch C controls outputs 2 & 4.
Output 1 & 3 are shown following input Ch A (open or closed)
o/p 1 - -
while Outputs 2 & 4 follow input Ch C.
- - o/p 2 Mode 2 however shows o/p 1, 2, 3 and 4 being in antiphase
o/p 3 - - to their inputs.
Mode 9 operates with both outputs for each channel being
- - o/p 4
in antiphase to their inputs.
Mode 2: As mode 1 with all outputs phase reversed Mode 3: 2 ch, 2 pole c/o output
i/p - Ch A i/p - Ch C i/p - Ch A i/p - Ch C
o/p 1 - - o/p 1 - -
- - o/p 2 o/p 2 - -
o/p 3 - - - - o/p 3
- - o/p 4 - - o/p 4
Mode 4: 1 ch with line fault output Mode 5: As mode 4 with c/o outputs
i/p - Ch A i/p - Ch A
No Line No Line No Line No Line

fault fault fault fault fault fault fault fault
o/p 1 o/p 1
o/p 2
No Line No Line
fault fault fault fault
o/p 3 No Line No Line
LFD o/p 3
LFD o/p 4
Mode 6: 1 ch with start/stop latch Mode 7: As mode 2 with LFD enabled
i/p Ch C Non-latching i/p Ch C Latching i/p - Ch A

i/p Ch B Enable Start Reset
i/p Ch A
i/p Ch A No Line No Line
Stop fault fault fault fault
i/p Ch B No effect
o/p 1
o/p 1 o/p 1
o/p 2 OR
o/p 2 o/p 3
o/p 3 o/p 3
o/p 4 i/p - Ch C
o/p 4
o/p 2
o/p 4
A B BRes
Start Stop et
i/p Ch A i/p Ch A *
Non-latching (enable) Latching

i/p Ch B i/p Ch B
Ch C open Ch C closed
o/p 1&3 o/p 1&3
o/p 2&4 o/p 2&4
* i/p Ch A can be open or closed when i/p Ch B opens to stop latch

* i/p Ch A can be open or closed when i/p Ch B opens to stop latch
INM 5500 Rev 10 23

MTL5510B modes - continued
Mode 9: 2 ch with line fault output Mode 10: As mode 9 with line fault c/o

o/p 1 o/p 1
i/p - Ch C
i/p - Ch C
No Line No Line
No Line No Line fault fault fault fault
o/p 2
o/p 2
No Line No Line
LFD o/p 3
LFD o/p 3
LFD o/p 4
Mode 11: As mode 10 with ch phase reversed Mode 12: 3 ch with common LFD output

o/p 1 o/p 1
i/p - Ch B
i/p - Ch C
No Line No Line
o/p 2
o/p 2
i/p - Ch C
No Line No Line
No Line No Line
LFD o/p 3 fault fault fault fault
LFD o/p 4 o/p 3
No Line No Line
Mode 13: As mode 12 but with LFD o/p 4 reversed
LFD o/p 4
No Line No Line
LFD o/p 4
Mode 14
This mode provides a two channel pulse stretcher for in- transition and the output polarity as shown in the timing
puts A and C. Outputs 1 and 2 respond to Ch A, while 3 and diagrams below.
4 respond to Ch C. When triggered by A (or C) the outputs hold the change
Input B (or D) being open or closed affects the input of state for a minimum of 1 second or as long as the input
(A or C) remains in the same triggered state.
Input Ch B (or D) closed Input Ch B (or D) open
i/p B (D) Initiate End

i/p B (D) Initiate End
i/p A (C)
i/p A (C)
1sec (min.)
o/p 1 (3)
o/p 1 (3)
1sec (min.)
o/p 2 (4)
o/p 2 (4)
24 INM 5500 Rev 10

6.1.5 MTL5511 - Switch/Proximity detector interface
Single channel, with line-fault detection
The MTL5511 contains a changeover relay, which enables a safe-area load to be controlled by a
switch or proximity detector located in a hazardous-area. When selected, the line-fault detect
(LFD) facility detects open or short circuit conditions in the field wiring and also indicates this on
the top of the module. Line-Fault Detect and Phase Reversal for the channel are selected by DIL
switches on the side of the module and output is provided by the changeover relay contacts.
See page 19 for LFD and PR switch details. Channel 1 only switch settings apply.
For switch sensor inputs, with LFD selected, make sure resistors (22kΩ and 680Ω) are fitted.
Note: For reliable, long-term operation the load on the output switching relay should be not less
6 7
5 8
4 9
680Ω
3 10
+
2 11 Output
22kΩ
– 1 12

13 Vs–
Switch-type sensors
14 Vs+
require resistors
if LFD is selected 20 to 35V dc
Figure 6.5:
Top label
for MTL5511
Terminal Function
1 Input –ve
2 Input +ve
10 Output normally-closed contact
11 Output common
12 Output normally-open contact
13 Supply –ve
14 Supply +ve
INM 5500 Rev 10 25

Two-channel, with line-fault detection and phase reversal
The MTL5513 enables two solid-state outputs in the safe area to be controlled by two switches
or proximity detectors located in the hazardous area. The Ch1/Ch2 output transistors share
a common terminal and can switch +ve or -ve polarity signals. Line-Fault Detect and Phase
Reversal for the channel are selected by DIL switches on the side of the module. LFD
indication is provided on the top of the module.
See page 19 for LFD and PR switch details. Channel 1 & 2 switch settings apply.

680Ω

6 7
22kΩ +
5 8
– 4
9 Outputs

680Ω 3 10 Ch 2
+
2 11
– 1 12 Ch 1
22kΩ

13 Vs–
14 Vs+
Switch-type sensors
require resistors 20 to 35V dc
Figure 6.6: if LFD is selected
Top label
for MTL5513
Terminal Function
1 Input –ve (Ch 1)
2 Input +ve (Ch 1)
5 Input +ve (Ch 2)
10 Output (Ch 2)
11 Output (Ch 1/Ch 2)
12 Output (Ch 1)
13 Supply –ve
14 Supply +ve
26 INM 5500 Rev 10

6.1.7 MTL5514(-T)/MTL5514D - Switch/Proximity detector interface
Single channel, with line-fault detection and phase reversal
The MTL5514(-T) enables a safe-area load to be controlled, through a relay, by a proximity

detector or switch located in a hazardous area. Line faults are signalled through a separate relay
and indicated on the top of the module. The MTL5514D provides signal duplication, enabling
two safe-area loads to be controlled by a single device in a hazardous area. Both relay outputs
reflect the input signal instead of one showing the line fault condition as in the MTL5514. Line-
Fault Detect and Phase Reversal for the channel are selected by DIL switches on the side of
the module and output is provided by changeover relay contacts.
See page 19 for LFD and PR switch details. Channel 1 only switch settings apply.
Note: For reliable, long-term operation the load on the output switching relays should be not less
6 7 7
5 LFD 8 LFD 8 O/P2
4 9 9
680Ω
3 10 10
+ O/P1
2 11 O/P 11
22kΩ 12
– 1 12
Switch-type sensors 13 Vs–

require resistors 14 Vs+
if LFD is selected 20 to 35V dc
Function
Terminal
MTL5514 (-T) MTL5514D
2 Input +ve (Ch 1)
7 LFD Output contact N.C. Output 2 contact N.C.
8 LFD Output common Output 2 common
Figure 6.7:
9 LFD Output contact N.O. Output 2 contact N.O.
Top label
10 Output contact N.C. Output 1 contact N.C.
for MTL5514 (-T) 11 Output common Output 1 common
& MTL5514D 12 Output contact N.O. Output 1 contact N.O.
13 Supply –ve
14 Supply +ve
INM 5500 Rev 10 27

6.1.8 MTL5516C - Switch/Proximity detector interface
Two channel, with line-fault detection
The MTL5516C contains two changeover relays, which enable two safe-area loads to be
controlled by switches or proximity detectors located in a hazardous-area. When selected, the
line-fault detect (LFD) facility detects open or short circuit conditions in the field wiring and
also indicates this on the top of the module. Line-Fault Detect and Phase Reversal for the
channel are selected by DIL switches on the side of the module and output is provided by the
changeover relay contacts.
680Ω

6 7
22kΩ +
5 8 Ch 2
– 4 9

680Ω 3 10
+
2 11 Ch 1
–
1 12
22kΩ

13 Vs–
14 Vs+
Switch-type sensors
if LFD is selected
Figure 6.8:
Top label
for MTL5516C
Terminal Function
2 Input +ve (Ch 1)
5 Input +ve (Ch 2)
7 Normally-closed contact (Ch 2)
8 Common (Ch 2)
9 Normally-open contact (Ch 2)
11 Common (Ch 1)
13 Supply –ve
14 Supply +ve
28 INM 5500 Rev 10

Two channel, with line-fault detection and phase reversal
The MTL5517 enables two safe-area loads to be controlled, through a relay, by switches or
proximity detectors located in a hazardous-area. When selected, the line-fault detect (LFD) is
signalled through a separate relay and indicated on the top of the module. Line-Fault Detect
and Phase Reversal for the channel are selected by DIL switches on the side of the module
and output is provided by the relay contacts.
680Ω

22kΩ + 6 7 LFD
5 LFD 8
– 4 Ch 2
9

680Ω LFD
3 10
+
2 11
– Ch 1
1 12
22kΩ

13 Vs–
14 Vs+
Switch-type sensors
if LFD is selected
Figure 6.9:
Top label
for MTL5517
Terminal Function
2 Input +ve (Ch 1)
5 Input +ve (Ch 2)
7 Line-fault detection
8 Output (Ch 2)
9 Output (Ch 2)
10 Line-fault detection
11 Output (Ch 1)
12 Output (Ch 1)
13 Supply –ve
14 Supply +ve
INM 5500 Rev 10 29

6.2 Digital Output modules
The single channel Digital Output (DO) module range enables on/off devices in a hazardous area
to be controlled from the safe area. Some units are loop powered while others enable solid-state
switching by providing independent power supplies.
6.2.1 MTL5521(-T) - Solenoid Alarm driver

Single channel, loop powered, IIC
The MTL5521(-T) is a loop-powered module that enables a device located in the hazardous area
(IIC gas group) to be controlled from the safe area. The MTL5521(-T) can drive a certified
intrinsically safe low-power load, as well as non-energy-storing simple apparatus such as an
LED.
To earth leakage
detector *
6 7
5 8
4 9
10 20 – 35Vdc
+ 3 –
2 11
12 +
– 1
Solenoid, alarm 13
or other IS device 14
Figure 6.10:
Top label
for MTL5521(-T)
Terminal Function
1 Output –ve
2 Output +ve
11 Supply –ve
12 Supply +ve
30 INM 5500 Rev 10

6.2.2 MTL5522 - Solenoid Alarm driver
Single channel, loop powered, IIB
The MTL5522 is a loop-powered module which enables a device located in the hazardous area
(IIB gas group) to be controlled from the safe area. The MTL5522 can drive a certified intrinsically
safe, low-power load as well as non-energy-storing simple apparatus such as an LED.
6 7
5 8
4 9
10 20 – 35Vdc
+ 3 –
2 11
12 +
– 1

Solenoid, alarm 13
Figure 6.11:
Top label
for MTL5522
Terminal Function
1 Output –ve
2 Output +ve
11 Supply –ve
12 Supply +ve
INM 5500 Rev 10 31

Single channel, with line-fault detection, IIC
The MTL5523 interface controls an on/off device in a hazardous area using a volt-free contact
or logic signal in the safe area, and is suitable for driving loads such as solenoids. Line-Fault
Detection (LFD) operates independently of the output state and is signalled by a safe-area,
solid-state switch output which, when a field line is open or short-circuited, becomes de-
energised. Earth-fault detection can be provided by connecting an MTL4220 earth leakage
detector to terminal 3.
6 7
5 8 LFD
‡
4 9
+ Control
3 10
+ –
2 11 +
– 1 12

Solenoid, alarm 13 Vs–
or other IS device 14 Vs+
20 to 35V dc
Figure 6.12: ‡ link to reverse output phase
Top label
for MTL5523
Terminal Function
1 Output –ve
2 Output +ve
7 Line fault signal -ve
8 Phase reversal link
10 Line fault signal +ve
11 Control –ve
12 Control +ve
13 Supply –ve
14 Supply +ve
32 INM 5500 Rev 10

6.2.4 MTL5523V/MTL5523VL - Solenoid Alarm driver
Single channel, voltage controlled with line-fault detection, IIC
With the MTL5523V or MTL5523VL interface, an on/off device in a hazardous area can be
controlled by a voltage signal in the safe area. It is suitable for driving loads such as solenoids.
Line fault detection (LFD), which operates irrespective of the output state, is signalled by a safe-
area, solid-state switch which energises if a field line is open or short–circuited.
The VL version has a lower current capability to suit alternative load requirements - see datasheet.
6 7
LFD
5 8
4 9
STS +
3 10 –
+ 2 11 V Control
MTL5523V +
1 12
–
PWR Solenoid, alarm 13 Vs–
20 to 35V dc
STS Terminal Function

MTL5523VL 1 Output –ve
2 Output +ve
PWR
7, 8, 9 Line fault signal –ve
10 Line fault signal +ve
11 Control –ve
Figure 6.13:
Top labels 12 Control +ve
for MTL5523V 13 Supply –ve
& MTL5523VL 14 Supply +ve
INM 5500 Rev 10 33

Single channel, powered, logic drive with phase reversal
The MTL5524 enables an on/off device in a hazardous area to be controlled by a volt-free

contact or logic signal in the safe area. It can drive loads such as solenoids, alarms, LEDs and
other low power devices that are certified as intrinsically safe or are classified as non-energy-
storing simple apparatus.
6 7
5 8
4 9 ‡
Control
3 10
+
–
2 11 +
– 1 12
Solenoid, alarm 13 Vs–

20 to 35V dc
‡ use link to reverse phase

Figure 6.14:
Top label
for MTL5524
Terminal Function
1 Output –ve
2 Output +ve
11 Control –ve
12 Control +ve
13 Supply –ve
14 Supply +ve
34 INM 5500 Rev 10

Single channel, low current, loop powered, IIC
The MTL5525 enables an on/off device in a hazardous area (IIC gas group) to be controlled
by a switch or voltage change in the safe area. It can drive loads such as solenoids, alarms,
LEDs and other low power devices that are certified as intrinsically safe or are classified as
non-energy-storing simple apparatus. Similar in function to the MTL5521, this module provides
lower power output and corresponding reduced safety description.
6 7
5 8
4 9
10 20 – 35Vdc
+ 3 –
2 11
12 +
– 1

Solenoid, alarm 13
Figure 6.15:
Top label
for MTL5525
Terminal Function
1 Output –ve
2 Output +ve
11 Supply –ve
12 Supply +ve
INM 5500 Rev 10 35

6.2.7 MTL5526 - Switch Operated Relay
Two channel, output
The MTL5526 enables two separate IS circuits in a hazardous area to be relay-contact controlled
by two on-off switches or logic signals in a safe area. Applications include the calibration of
strain–gauge bridges; changing the polarity (and thereby the tone) of an IS sounder; the testing
of IS fire alarms; and the transfer of safe-area signals into an annunciator with IS input terminals
not segregated from each other.
The output–relay contacts are certified as non–energy–storing apparatus, and can be connected
to any IS circuit without further certification, provided that separate IS circuits are such that
they would remain safe if connected together.

Contact Loop
inputs powered
1 7 +
1 2
+
8
IS relay
3 9
–
– Control
1
Sw4 + 20 to
4 10
+ 35V dc
IS relay
11
–
2 5 –
12 2
6

All contacts shown 13 Vs–
in normal position 14 Vs+
(relays de-energised)
20 to 35V dc
Figure 6.16:
Top label
for MTL5526
Terminal Function
1 IS relay output 1 (normally open)
2 IS relay output 1 (normally closed)
3 IS relay output 1 (common)
4 IS relay output 2 (common)
5 IS relay output 2 (normally closed)
6 IS relay output 2 (normally open)
8 Relay 1 control +ve
9 Relay 1 control –ve
10 Relay 2 control +ve
11 Relay 2 control –ve
13 Supply –ve
14 Supply +ve
Mode Function SW1 SW2 SW3 SW4
Table 6.3: Contact/Logic 2 ch Off On On On

Switch settings
for modes Input 1in2out On On On On
Loop Powered 2 ch Off Off Off Off
1234
OFF position
ON position
36 INM 5500 Rev 10

6.3 Pulse and Vibration modules
Single and dual channel modules are available to transfer vibration probe signals from a
hazardous area to a safe one. Similarly, pulses from a switch, proximity detector, current pulse
transmitter or voltage pulse transmitter, located in the hazardous area, can be safely transferred
to the safe area.
6.3.1 MTL5531 - Vibration Transducer Interface

Single channel
The MTL5531 repeats a signal from a vibration sensor in a hazardous area, providing an output
for a monitoring system in the safe area. The interface is compatible with 3-wire, eddy-current
probes and accelerometers or 2-wire current sensors, and selection of the mode is made with
a switch located on the side of the module
6 7
5 8
4 9
COM
3 10 –ve
3- Vibration SIG
wire transducer 2 11 Monitor
V–
1 12
0V
3
2- Vibration 13 Vs–
2
wire transducer 14 Vs+
1
20 to 35V dc
Figure 6.17:
Top label
for MTL5531
Terminal Function
1 Transducer power V–
2 Signal
3 Common
11 Signal output –ve
12 Signal output 0V
13 Supply –ve
14 Supply +ve
2-/3-wire transducer setting switch
OFF position
ON position
2-/3-wire
* Note: When using 2-wire sensors,

Mode SW
ensure that terminals 1 and 2 are linked
2-wire (3.3mA)* OFF as shown in the wiring diagram above.
3-wire (20mA) ON
WARNING - Revision status 05 and below*

To enable optimum heat dissipation the recommended orientation for mounting is
with the module vertical, i.e. with the vents in the case at the top and bottom. This
enables air to flow through the module.
In any other orientation, i.e. with the module horizontal, then the maximum ambient
temperature is limited to:
• Close packed = 45°C
• Minimum of 10mm spacing = 55°C
Eaton produce the MS010 DIN rail module spacer for this purpose
(packs of 5 - see Section 4.3)
*Revision status is the 2 digits after the +++ in the barcode number
INM 5500 Rev 10 37

6.3.2 MTL5532 - Pulse Isolator
Pulse & 4/20mA current outputs
The MTL5532 isolates pulses from a switch, proximity detector, current pulse transmitter
or voltage pulse transmitter located in a hazardous area. It is ideal for applications involving
high pulse rates and fast response times, by repeating the pulses into the safe area, and the
transistors used on the pulse output will switch +ve or –ve polarity signals.
It may be used immediately in simple or legacy mode, or it may be software configured for more
specific applications - see next page for either option. With configuration, an analogue output
proportional to frequency is available, together with a relay output, which may act as an alarm.
Note: For reliable, long-term operation the load on the output switching relay should not be less
than 50mW, e.g.10mA at 5VDC.
5
Current Configuration
pulse socket
3
V Inhibit
4/20
mA 4/20mA
+ –
1 1 6 7
5 8 Load
Voltage
pulse 4 4 9 +
Pulse Alarm
3-wire 3 3 10
+
current
4/20 2 11 –
mA
12 + Pulse
pulse 1 – 1
5 2-wire 13 Vs–
4 current 4 14 Vs+
Figure 6.18: 3-wire pulse 20 to 35V dc
voltage 3
Top label pulse 4/20
mA
for MTL5532 1
Terminal Function
1 Common input –ve
2 Switch/proximity input +ve
3 Current pulse input +ve
4 Transmitter supply +ve
5 Voltage pulse input +ve
6 Inhibit input +ve
7 Alarm output
8 Current output –ve
9 Current output +ve
10 Alarm output
11 Pulse output –ve
12 Pulse output +ve
13 Supply –ve
14 Supply +ve
Switches located on the edge of the module define the mode of operation.
SW1 SW2 SW3 SW4

Vsp Vsp LFD Mode
1234
OFF position
ON position
Vsp SW1 SW2 LFD SW3

3V ON ON OFF OFF
6V ON OFF ON ON
12V OFF OFF
38 INM 5500 Rev 10

Switch input operation
If switch contacts are used for this Pulse Input (terminals 1 & 2), then and parallel resistors
must be fitted - see Section 6.1.2 for recommended values.
Simple or Legacy mode - SW4 - OFF

If simple “pulse-in/pulse-out” operation is required or, if a replacement for the earlier MTL5032
pulse isolator is required, then SW4 should be set to OFF. The input switching point voltage
(Vsp) thresholds can then be defined by Switches 1 & 2, and the LFD operation can be set with
Switch 3. When Switch 3 is ON, the Alarm output (terminals 11 & 12) become active.
Configurable mode - SW4 - ON

In this mode, analogue, alarm and pulse outputs are available but the module must be software
configured to define its operating mode. In this mode, software controls the LFD function and
Switch 3 has no effect. Switches 1 & 2 continue to define the switching point threshold (Vsp).
Configuration requires a personal computer, a PCL45USB interface and PCS45 software. See
Section 6.9 for details of the configurator.
Alarm inhibiting
The Inhibit input is provided to inhibit alarm output operation. This facility is useful, for example,
during power-up, when pulse rates are below the alarm threshold. When normal operational
values are established the inhibit can be disabled. Such a facility is sometimes referred to
as a start-up delay. Inhibit is enabled by connecting a switch or proximity detector between
terminals 6 and 3. If switch contacts are used for this input, then and parallel resistors must be
fitted - see Section 6.1.2 for recommended values.
LED indicators
Use the following LED information to understand the module status.
LED Description
PWR
ON - Power OK OFF - No power or insufficient voltage
Power (green)
O/P The LED will follow the pulse output state. If the output is pulsing then
Output (yellow) the LED brightness will pulse. If the pulsing is rapid or very short, the LED
may dim if it is unable to respond to such changes.
If the output is high, the LED will be ON.
STS In legacy mode a line fault will cause the LED to turn ON.
Status In mC mode, the LED is programmable to display a line fault or an Alarm
(red - flashing) trip operation. In the event, it will also indicate a mC fault condition.
INM 5500 Rev 10 39

6.3.3 MTL5533 - Vibration Transducer Interface
(Reference use only: Terminated product, use 2 x MTL5531)
Two channel
The MTL5533 repeats signals from vibration sensors in a hazardous area, providing outputs
for monitoring systems in the safe area. The interface is compatible with 3-wire eddy-current
probes and accelerometers or 2-wire current sensors, and selection of the mode for each
channel is made with the switches on the side of the module.
6
2- Vibration
wire transducer 5
4
Ch 2
COM Ch 2
6 7 –ve
3- Vibration SIG
wire transducer 5 8 Monitor
V– 4 9
0V
COM 10 –ve Ch 1
3- Vibration 3
SIG 11
wire transducer 2 Monitor
V– 12
1
Ch 1 0V
3
2- Vibration 13 Vs–
2
wire transducer 14 Vs+
1
20 to 35V dc
Figure 6.19:
Top label
for MTL5533
Terminal Function
1 Transducer power V– (Ch1)
2 Signal (Ch1)
3 Common (Ch1)
4 Transducer power V– (Ch2)
5 Signal (Ch2)
6 Common (Ch2)
8 Signal output –ve (Ch2)
9 Signal output 0V (Ch2)
11 Signal output –ve (Ch1)
12 Signal output 0V (Ch1)
13 Supply –ve
14 Supply +ve
2-/3-wire transducer setting switches
OFF position
ON position
Ch 1 Ch 2
* Note: When using 2-wire sensors, ensure

Mode SW
that terminals 1 & 2 and 4 & 5 have wiring
2-wire (3.3mA) OFF links as shown in the wiring diagram above.
3-wire (20mA) ON
WARNING!
To enable adequate heat dissipation from the MTL5533 modules, they

must be installed on the DIN rail with a 10mm space between adjacent
units. Eaton produce the MS010 DIN rail module spacer for this purpose
(packs of 5 - see Section 4.3), and these then enable operation in ambient
temperatures of up to 50°C in vertical or horizontal orientation.
40 INM 5500 Rev 10

6.4 Analogue Input modules
The analogue input (AI) modules support 2-wire or 3-wire 4/20mA or HART transmitters located
in a hazardous area; repeating the current in other circuits to drive safe-area loads.
6.4.1 MTL5541/MTL5541S (-T) - Repeater Power Supply

Single channel, for 4/20mA HART® for 2- or 3-wire transmitters
The MTL5541 provides a fully-floating dc supply for energising a conventional 2- or 3-wire

4/20mA transmitter which is located in a hazardous area, and repeats the current in another
floating circuit to drive a safe-area load. For HART 2-wire transmitters, the unit allows bi-
directional communications signals superimposed on the 4/20mA loop current. Alternatively,
the MTL5541S (-T) acts as a current sink for a safe-area connection rather than driving a
current into the load. Separately powered current sources, such as 4-wire transmitters, can be
connected but will not support HART communication.
6 7
5 8
4 9 MTL5541 MTL5541S
Com I
3 10 +
Tx+ – +
2 11
Input I 4/20mA
–
1 12 –
4/20mA
+ Load Load
13 Vs–
14 Vs+
20 to 35V dc
S Terminal Function
1 Current input
3 Common
Figure 6.20: 10 Output +ve via 220Ω for HART apps.
Top labels 11 Output –ve (+ve current sink)
for MTL5541
12 Output +ve (–ve current sink)
& MTL5541S
13 Supply –ve
14 Supply +ve
INM 5500 Rev 10 41

6.4.2 MTL5541A/MTL5541AS - Repeater Power Supply
Single channel, for 4/20mA, HART® for 2- or 3-wire transmitters
The MTL5541A provides an input for separately powered 4/20mA transmitters and also allows
bi–directional transmission of HART communication signals superimposed on the 4/20mA loop
current. Alternatively, the MTL5541AS acts as a current sink for a safe-area connection rather
than driving a current into the load.
6 7
5 8
4 9 MTL5541A MTL5541AS
Load Load

+ 3 I 10 + +
–
4/20mA 2
11
I 4/20mA
–
– 1 12 + –
13 Vs–
14 Vs+
20 to 35V dc

Terminal Function

1 Input –ve
2 Input +ve
11 Output –ve (+ve current sink)
Figure 6.21:
12 Output +ve (–ve current sink)
Top labels
13 Supply –ve
for MTL5541A
14 Supply +ve
& MTL5541AS
42 INM 5500 Rev 10

6.4.3 MTL5544/MTL5544S - Repeater Power Supply
Two channel, for 4/20mA HART® for 2- or 3-wire transmitters
The MTL5544 provides fully-floating dc supplies for energising two conventional 2-wire or
3-wire 4/20mA or HART transmitters located in a hazardous area, and repeats the current in
other circuits to drive two safe-area loads. For HART transmitters, the unit allows bi-directional
transmission of digital communication signals superimposed on the 4/20mA loop current.
Alternatively, the MTL5544S acts as a current sink for a safe-area connection rather than driving
a current into the load. Separately powered current sources, such as 4-wire transmitters, can
be connected but will not support HART communication.
MTL5544 MTL5544S
Ch 2 Com Ch 2
Tx+ 6 I 7
– +
5 8
Input 4/20mA
4 I 9 –
4/20mA + Load Load
Com Ch 1
3 I 10 +
Tx+ –
2 11
Input 4/20mA
1 I 12 –
4/20mA + Load Load
Ch 1
13 Vs–
14 Vs+
20 to 35V dc
Terminal Function

1 Ch1 current input

2 Ch1 transmitter supply +ve
3 Ch1 common
4 Ch2 current input
Figure 6.22:
5 Ch2 transmitter supply +ve
Top labels
6 Ch2 common
for MTL5544
7 Ch2 output +ve via 220Ω for HART apps.
& MTL5544S
8 Ch2 output –ve (+ve current sink)
9 Ch2 output +ve (–ve current sink)
13 Supply –ve
14 Supply +ve
The MTL5544 or MTL5544S Hazardous Safe area

can also be used to drive two area
safe-area loads from a single
2-wire transmitter (i.e. 1 in, MTL5544 MTL5544S
2 out) by interconnecting the 6 7 Ch 2 Load
I
– +
input channels as shown in 4/20mA 5 8
– 4 I 9
4/20mA
–
the diagram (right). + Load
Ch 1 Load
3 I 10 +
Note: In this mode the HART 11 –
+ 2 4/20mA
data is transferred via channel 1 I 12
+
–
Load
1 output only. 13 Vs–
14 Vs+
See also the MTL5544D. 20 to 35V dc
INM 5500 Rev 10 43

6.4.4 MTL5544A/MTL5544AS - Current Repeater
Two channel, for 4/20mA passive input for HART® transmitters
The MTL5544A provides an input for separately powered 4/20mA transmitters and also allows
bi–directional transmission of HART communication signals superimposed on the 4/20mA loop
current. Alternatively, the MTL5544AS acts as a current sink for a safe-area connection rather
than driving a current into the load.
MTL5544A MTL5544AS
Ch 2 Load
+ 6 I 7
– + +
5 8
Ch 2 4/20mA 4/20mA
–
4 I 9 –
– + Load
Load
3 I 10 Ch 1 +
+ – +
2 11
Ch 1 4/20mA 4/20mA
I 12 –
– 1 + Load –
13 Vs–
14 Vs+
20 to 35V dc

Terminal Function

1 Ch1 input –ve
2 Ch1 input +ve
4 Ch2 input –ve
Figure 6.23:
5 Ch2 input +ve
Top labels
for MTL5544A
& MTL5544AS
13 Supply –ve
14 Supply +ve
44 INM 5500 Rev 10

6.4.5 MTL5544D - Repeater Power Supply
Two channel, for 4/20mA HART® for 2- or 3-wire transmitters, two outputs
The MTL5544D provides a fully-floating dc supply for energising a conventional 2- or 3-wire

4/20mA transmitter located in a hazardous area, and repeats the current in other circuits
to drive two safe-area loads. For HART 2-wire transmitters, the unit allows bi-directional
transmission of digital communication signals superimposed on the 4/20mA loop current.
Separately powered current sources, such as 4-wire transmitters, can be connected but will
not support HART communication.
Ch 2
6 7
I –
5 8 4/20mA
4 9 + Load
Com I Ch 1
Tx+ 3 10
11
–
Input 2 I 4/20mA
1 12

4/20mA
+ Load
13 Vs–
14 Vs+
20 to 35V dc
Figure 6.24:
Top label
for MTL5544D
Terminal Function
1 Current input
3 Common
8 Ch2 output –ve
9 Ch2 output +ve
11 Ch1 output –ve
12 Ch1 output +ve
13 Supply –ve
14 Supply +ve
NOTE: For correct operation of the module, a suitable load must be present on both output channels.
This is of particular importance during testing, commissioning or maintenance activities when the
temporary disconnection, or absence, of a load can affect the transfer accuracy of the analogue variable.
INM 5500 Rev 10 45

6.5 Analogue Output modules
The analogue output (AO) modules accept 4/20mA floating signals from safe-area controllers to
drive current/pressure converters (or any other load up to 800Ω) in a hazardous area.
6.5.1 MTL5546/MTL5546Y(-T) - Isolating Driver

Single channel, for 4/20mA HART® valve positioners with line-fault detection
The MTL5546 accepts a 4/20mA floating signal from a safe-area controller to drive a current/
pressure converter (or any other load up to 800Ω) in a hazardous area. For HART valve
positioners, the module also permits bi-directional transmission of digital communication
signals so that the device can be interrogated either from the operator station or by a hand-held
communicator. Process controllers with a readback facility can detect open or short circuits in
the field wiring: if these occur, the current taken into the terminals drops to a preset level. The
MTL5546Y(-T) is very similar to the MTL5546 except that it provides open circuit detection only
(i.e. no short-circuit detection).

Terminal Function
1 Output –ve

2 Output +ve
11 Input –ve
Figure 6.25: 12 Input +ve
Top labels 13 Supply –ve
for MTL5546 14 Supply +ve
& MTL5546Y
Input characteristics
Field wiring state MTL5546 MTL5546Y
Normal <6.0V <6.0V
Open-circuit <0.9mA <0.5mA
Short-circuit <0.9mA N.A.
46 INM 5500 Rev 10

6.5.2 MTL5549/ MTL5549Y - Isolating Driver
Two channel, for 4/20mA HART® valve positioners with line-fault detection
The MTL5549 accepts 4/20mA floating signals from safe-area controllers to drive 2 current/
pressure converters (or any other load up to 800Ω) in a hazardous area. For HART valve
positioners, the module also permits bi-directional transmission of digital communication
signals so that the device can be interrogated either from the operator station or by a hand-held
communicator. Process controllers with a readback facility can detect open or short circuits in
the field wiring: if these occur, the current taken into the terminals drops to a preset level. The
MTL5549Y is very similar to the MTL5549 except that it provides open circuit detection only
(i.e. no short-circuit detection).

Terminal Function

1 Output –ve (Ch 1)

2 Output +ve (Ch 1)
5 Output +ve (Ch 2)
Figure 6.26:
Top labels
for MTL5549 9 Input +ve (Ch 2)
& MTL5549Y 11 Input –ve (Ch 1)
12 Input +ve (Ch 1)
13 Supply –ve
14 Supply +ve
Input characteristics
Field wiring state MTL5549 MTL5549Y
Normal <6.0V <6.0V
Open-circuit <0.9mA <0.5mA
Short-circuit <0.9mA N.A.
INM 5500 Rev 10 47

6.6 Fire and Smoke Interface modules
Interfaces for use with conventional fire and smoke detectors located in hazardous areas.
6.6.1 MTL5561 - Fire and Smoke Detector Interface

Two channel
The MTL5561 is a loop-powered 2–channel interface for use with conventional fire and
smoke detectors located in hazardous areas. In operation, the triggering of a detector causes
a corresponding change in the safe–area current. The unit features reverse input polarity
protection.
Ch 2
6 I 7
+ –
5 8
Ch 2
– 4 I 9
+
Fire
detectors 10
+ 3
I
11 –
2
I 12 Ch 1
1
– +
13
Ch 1 14
Figure 6.27:
Top label
for MTL5561
Terminal Function
2 Output +ve (Ch 1)
5 Output +ve (Ch 2)
9 Input +ve (Ch 2)
12 Input +ve (Ch 1)
48 INM 5500 Rev 10

6.7 Temperature Input module
These modules accept inputs from low-level dc sources such as thermocouples or RTDs in
hazardous areas and converts them into 4/20mA signals to drive safe area loads.
Thermocouples Early burnout detection (EBD)
When EBD is selected, the resistance of the thermocouple circuit is monitored and an alarm is
raised when there is an increase of more than 50W. This enables preventative maintenance to
be conducted on the field installation before the thermocouple actually breaks.
Configuration using PCS45/PCL45USB

Use PCS45 software, in conjunction with the PCL45USB serial link, to configure these modules.
Instructions are contained within the software. See Section 6.9 on page 58 for further details.
All MTL5573 and MTL5575 modules are supplied with the following default configuration.
Input type Type K thermocouple

Linearisation enabled
Units °C
CJ Compensation enabled
Damping value 0 seconds
Smoothing value 0 seconds
Output zero 0°C
Output span 250°C
Tag and description fields blank
Open circuit alarm set high (upscale)
Transmitter failure alarm set low (downscale)
CJ failure alarm set low (downscale)
Line frequency 50Hz
Use PCS45 software, in conjunction with the PCL45USB serial link, to modify these default values.
INM 5500 Rev 10 49

6.7.1 MTL5573 - Temperature Converter
Single channel, THC or RTD input
The MTL5573 converts a low-level dc signal from a temperature sensor mounted

in a hazardous area into a 4/20mA current for driving a safe-area load. Software
selectable features include linearisation, ranging, monitoring, testing and tagging for all
thermocouple types and 2-, 3- or 4-wire RTDs. (For thermocouple applications the HAZ-
CJC plug on terminals 1–3 includes an integral CJC sensor). Configuration is carried out
using a personal computer.

Configuration
socket
4-wire 6 7
5 8
4 mV 9
3-wire
+ Load
3 10 –
mV I 11
– 2 4/20mA
1 12
+
13 Vs–
3 14 Vs+
20 to 35V dc
Figure 6.32:
Top labels for Terminal Function
MTL5573
1 THC/EMF/RTD input –ve
3 THC/EMF/RTD input +ve
4 3-wire RTD input –ve
5 4-wire RTD input +ve
11 Output –ve
12 Output +ve
13 Supply –ve
14 Supply +ve
Top label
Status PWR (green) STS(yellow)

Power ON ON
Insufficient voltage or Power OFF OFF
Normal working ON
Device failure FLASH
Sensor failure/Error FLASH
Early burnout detection (EBD) FAST FLASH
50 INM 5500 Rev 10

6.7.2 MTL5575 - Temperature Converter
Single channel, THC or RTD input with alarm
The MTL5575 converts a low-level dc signal from a temperature sensor mounted in a

hazardous area into a 4/20mA current for driving a safe-area load. Software selectable features
include linearisation, ranging, monitoring, testing and tagging for all thermocouple types and 2,
3 or
4-wire RTDs. (For thermocouple applications the HAZ-CJC plug, on terminals 1–3, includes an
integral CJC sensor). Configuration is carried out using a personal computer - see section 6.9. A
single alarm output is provided and may be configured for process alarm or to provide notice of
early thermocouple failure.

Figure 6.28:

Top label
for MTL5575
Terminal Function
1 THC/EMF/RTD input –ve
3 THC/EMF/RTD input +ve
8 Alarm relay
9 Alarm relay
11 Output –ve
12 Output +ve
13 Supply –ve
14 Supply +ve
Top label
Status PWR (green) STS(yellow)

Power ON ON
Normal working ON
Device failure FLASH
Sensor failure/Error FLASH
Output relay ON (Trip) ON ON
Output relay OFF (Trip) ON OFF
Early burnout detection (EBD) FAST FLASH
INM 5500 Rev 10 51

6.7.3 MTL5576-RTD - Temperature Converter
Two channel, RTD/potentiometer input
The MTL5576-RTD converts signals from resistance temperature detectors (RTDs) mounted
in a hazardous area, into 4/20mA currents for driving safe-area loads. The MTL5576-RTD is
compatible with 2- and 3-wire RTD inputs.
Performance features, including input type and characterisation, ranging, monitoring, testing
and tagging are selected using PCS45 software, which is loaded onto a personal computer and
connected via the PCL45USB serial link - see Section 6.9.

Figure 6.29:
Top label
for MTL5576
Terminal Function
1 RTD input (Ch1)
2 RTD input (Ch1)
3 3–wire RTD input (Ch1)
4 RTD input (Ch2)
5 RTD input (Ch2)
6 3–wire RTD input (Ch2)
8 Output –ve (Ch2)
9 Output +ve (Ch2)
12 Output +ve (Ch1)
13 Supply –ve
14 Supply +ve
Top label
Status PWR (green) FLT (red) STS(yellow)

Power ON ON
Communication in progress FLASH
Normal working ON OFF OFF
Device failure ON ON
Channel 1 - Sensor failure/Error ON FLASH OFF
Channel 2 - Sensor failure/Error ON FLASH ON
Default configuration for both channels is as shown in 6.7 except S/C alarm set OFF.
52 INM 5500 Rev 10

6.7.4 MTL5576-THC - Temperature Converter
Two channel, mV/THC input
The MTL5576-THC converts low-level dc signals from temperature sensors mounted in

a hazardous area, into 4/20mA currents for driving safe-area loads. The hazardous area
connections include cold-junction compensation and do not need to be ordered separately.
Performance features, including linearisation for standard thermocouple types, ranging,

monitoring, testing and tagging are selected using PCS45 software, which is loaded onto a
personal computer and connected via the PCL45USB serial link - see Section 6.9.
Top label

Figure 6.30:

Top label
for MTL5576
Terminal Function
1 THC/mV (Ch1)
3 THC/mV (Ch1)
4 THC/mV (Ch2)
6 THC/mV (Ch2)
9 Output +ve (Ch2)
12 Output +ve (Ch1)
13 Supply –ve
14 Supply +ve
Status PWR (green) FLT (red) STS(yellow)

Power ON ON
Communication in progress FLASH
Normal working ON OFF OFF
Device failure ON ON
Channel 1 - Sensor failure/Error ON FLASH OFF
Channel 2 - Sensor failure/Error ON FLASH ON
Default configuration for both channels is as shown in 6.7 except S/C alarm set OFF.
INM 5500 Rev 10 53

6.7.5 MTL5581 - mV/Thermocouple Isolator
Single channel, mV/THC input for low power signals
The MTL5581 takes a low-level dc signal from a voltage source in a hazardous area, isolates it,
and passes it to a receiving instrument located in the safe area. The module is intended for use
with thermocouples utilising external cold-junction compensation. A switch enables or disables
the safety drive in the event of thermocouple burnout or a cable breakage; a second switch
permits the selection of upscale or downscale operation as the application requires.
6 7
5 8
4 9 *Use compensating
cable with
thermocouple inputs
3 mV 10
MTL5581 + 2 11 –
mV mV Output*
1 12
– +
PWR
13 Vs–
14 Vs+
20 to 35V dc
Figure 6.31:
Top label
for MTL5581
Terminal Function
1 THC/mV input –ve
2 THC/mV input +ve
11 Output –ve
12 Output +ve
13 Supply –ve
14 Supply +ve
Please note that the safety drive on the MTL5581 responds to a line breakage (i.e. an open circuit)
or a thermocouple burnout. It does not provide detection of a short circuit. It can however, when
chosen, be set to drive the output either upscale or downscale. These options are selected using
the switches located on the side of the module.
Safety drive switches

Line
Sw2 Sw1 Vout value
breakage
Safety drive Drive direction
OFF N/A NO Vin*
OFF N/A YES undetermined
ON + NO Vin*
ON + YES > +50mV
ON – NO Vin*
ON – YES < –50mV
* Within Vin/Vout transfer accuracy and drift error as specified in the product datasheet.
Safety drive switches
OFF position
ON position
Sw 1 Sw 2
Sw1 OFF ON Sw2 OFF ON
Drive direction ‘+’ Upscale ‘–’ Downscale Safety drive OFF ON
54 INM 5500 Rev 10

6.7.6 MTL5582/MTL5582B - Resistance Isolator
Single channel, to repeat RTD signals
The MTL5582 or MTL5582B connect to a 2-, 3-, or 4-wire resistance temperature device (RTD)
or other resistance located in a hazardous area, isolates it and repeats the resistance to a
monitoring system in the safe area. The module is intended typically (but not exclusively) for
use with Pt100 3-wire RTDs. Switches enable selection of 2-, 3-, or 4-wire RTD connection.
The MTL5582/ MTL5582B should be considered as an alternative, non-configurable MTL5575,
for use in RTD applications where a resistance input is preferred or needed instead of 4/20mA.
The design is notable for its ease of use and repeatability. The number of wires which can
be connected on the safe-area side of the unit is independent of the number of wires which
can be connected on the hazardous-area side. The module drives upscale in the case of open
circuit detection. The MTL5582B replaced the MTL5582 during 2016 to improve the response
characteristics of the safe area circuit.

MTL5582

PWR

Figure 6.32:
Top label
for MTL5582/
MTL5582B
Terminal Function
1 RTD input –ve
3 RTD input +ve
9 RTD output –ve
10 RTD output +ve
11 RTD output –ve
12 RTD output +ve
13 Supply –ve
14 Supply +ve
Warning: Check polarity of terminals used for safe-area connections. Safe-area terminals
9, 10, 11 and 12 are unipolar so it is essential to select a positive terminal on the MTL5582/
MTL5582B for connection to the positive of the RTD input card.
RTD type selection switches
OFF position
ON position
Sw 1
Sw 1Sw 2 Sw 2
2-wire OFF ON
3-wire ON ON
4-wire ON OFF
INM 5500 Rev 10 55

6.8 General modules
These are general purpose modules that have applications associated with the MTL5500 range
of modules.
6.8.1 MTL5599 - Dummy Isolator

The primary function of the MTL5599, is to provide termination and earthing facilities for
unused cable cores from hazardous areas, that can occur, for example, if any MTL5500 module
has been removed for maintenance purposes.
6.8.2 MTL5991 - 24V dc power supply
Safe area

56 INM 5500 Rev 10

The MTL5991 provides a convenient source of power for DIN-rail mounted units in locations
where a dc supply is not readily available. The wide input power supply range makes this
unit universally applicable and the 2A output capability at 24V dc is sufficient to drive a useful
number of MTL5500 modules - see table below. See also the MPA5500, in Section 4.2 of this
manual, for powering individual modules.
Safe area

Terminal Function
1 AC line
2 Earth
3 AC neutral
4 +24V
5 +24V
6 0V
7 0V
8 Do not use
MTL5500 Current Drawn Max. number

unit mA (Vs=24V) of units
MTL5501-SR 90 22
MTL5510 40 50
MTL5510B 40 50
MTL5511 25 80
MTL5513 30 66
MTL5514(-T)/D 25 80
MTL5516C 35 57
MTL5517 35 57
MTL5521(-T) 90 22
MTL5522 125 16
MTL5523V/VL 100 20
MTL5524 100 20
MTL5525 100 20
MTL5526 44 45
MTL5531 96 20
MTL5532 65 30
MTL5533 130 15
MTL5541/S(-T) 51 39
MTL5541A/AS 45 44
MTL5544/D/S 96 20
MTL5544A/AS 70 28
MTL5546/Y(-T) 35 57
MTL5549/Y 70 28
MTL5573/75 50 40
MTL5576 60 33
MTL5581 30 66
MTL5582/82B 33 60
INM 5500 Rev 10 57

6.9 PCS45/PCL45USB configurator for MTL temperature converters
The PCS45/PCL45USB configurator allows MTL isolating temperature converters to be configured

from a standard PC running a Microsoft® Windows® operating system. The configurator comprises
PC software provided on a CD (PCS45), and an ATEX certified interfacing link (PCL45USB).
Temperature converters can be configured from the safe area, while on-line, and the software allows
configurations to be saved to disk and printed out when required.
Safe area
It is suitable for use with MTL4000, MTL4500, MTL5000 and MTL5500 products.
PCL45USB hardware
The PCL45USB provides the interfacing link between the converter module and the PC running
the software and connects to the PC using the USB cable provided. The PCL45USB has a built-in
cable fitted with a 3.5mm jackplug to connect to the ‘Config’ socket on MTL4500 and MTL5500
converters. An adapter cable is also provided to accommodate our earlier converters.
PCS45 Configuration software

The software provided on the CD requires only approximately 20Mb of hard disk space and is
compatible with Windows 2000, Windows XP or Windows 7. Ensure that the chosen PC has a CD
ROM drive and an available USB port. A local or network printer may also be an advantage.
Safety
It is not permitted to connect the PCL45USB to any device other than one approved by Eaton.
Authorisation is valid provided that the converter type is named on the PCL45USB certificate or if
the PCL45USB is specified on the converter certificate. Repairs to the PCL45USB are not permitted.
Setting up
The equipment can be used only in the safe area.
Before plugging in the PCL45USB link to the computer, extract the USB driver files to a known
location on your PC. Afterwards, plug in the PCL45USB to the USB port on the PC and wait for
it to find the new device. When requested by the computer, show it the location of the driver
files so that it can complete the device installation.
Place the PCS45 software CD in the computer’s CDROM drive and follow the on-screen
instructions to install the software.
The PCL45USB is powered from the data lines and quickly establishes communication after
plugging the 3.5mm connector to the device socket.
Note: Ensure that the 3.5mm jack plug is fully inserted into the socket of the temperature converter.
The software and its operations manual (INM PCS45) is available on-line at:
http://www.mtl-inst.com/product/configuration_tools_and_software/
58 INM 5500 Rev 10

7 FAULT FINDING AND ROUTINE MAINTENANCE
WARNING
On removal, take care that a hazardous-area connector is not laid in a
position in which it may inadvertently come into contact with safe-area
circuit components.
7.1 Maintenance precautions

Most Codes of Practice for intrinsic safety permit live maintenance on intrinsically safe devices
and systems, provided precautions are taken to preserve the integrity of the device or system.
During live maintenance of MTL5500 modules, the hazardous-area connectors that plug into
the tops of the modules are likely to be removed. Avoid leaving a hazardous-area connector
in a position where it may inadvertently contact non-IS circuits that are nearby. Prevent this by
providing some form of temporary mechanical method of securing the connector so that it cannot
come into contact with the non-IS circuits:
a) By plugging the connector into an MTL5599 dummy isolator

b) By using a tiewrap to constrain the connector in a safe position.
7.2 Fault finding

When fault finding, carry out the following steps as far as is necessary:–
7.2.1
Check that all modules with power (PWR) LEDs are ON.
With the MTL5575 & MTL5576 models, a flashing LED indicates alarm or fault conditions, refer
to section 8. Note: The LED may also flash during intermediate stages of configuration.
7.2.2
Exchange potentially faulty modules for working units as follows:–
a) Unplug the hazardous-area connectors, then the safe area connectors.
b) Unplug any power connectors and remove from DIN rail.
c) Reverse this procedure to fit a replacement module.
7.2.3
Potentially faulty modules should be tested in workshop conditions, using an appropriate test
procedure for the particular module as described in Section 8.
7.3 Routine maintenance

Check the general condition of the installation occasionally to make sure that no deterioration
has occurred. Carry out the following at least once every two years and more frequently for
particularly harsh environments:–
a) Check that modules are of the types specified in the relevant documentation.
b) Check that modules and hazardous-area connectors are correctly and legibly tagged, that
the connectors are plugged into the matching modules and that the tag details given
comply with the relevant documentation.
c) Check that hazardous- and safe-area connectors are securely plugged into their matching
sockets.
d) Check that all connections to the connectors are properly made.
e) Check that cables to connectors are of the specified type and rating, are correctly routed
and segregated (particularly in Eaton enclosures), and are not frayed or otherwise damaged.
f) Check that cable screens are properly earthed.
Note: It is strongly recommended that only the tests (described in Section 8) and routine
maintenance (described here) should be undertaken by users. If a module is faulty, DO NOT
attempt to make repairs or modifications as these may affect the intrinsic safety of the module.
All faulty units should be returned to the Eaton’s MTL product line or representative from which
they were purchased, for repair or replacement.
INM 5500 Rev 10 59

8 BENCH TESTING MODULES
The following methods have been devised to permit the user to perform simple module tests
on the bench and confirm basic input to output operation. Field units that do not perform as
described below, or modules that have ‘unusual’ operating behaviour, should be replaced and
returned to Eaton.
Consult individual module wiring diagrams for terminal connections.
Unless stated specifically, the module will require dc power, as if under normal
operating conditions.
8.1 Digital Input (DI) modules

8.1.1 Modules: MTL 5501-SR, MTL5510, MTL5510B, MTL5511, MTL5513, MTL5514(-T),
MTL5514D, MTL5516C, MTL5517
Input Conditions
1. Connect the appropriate input test circuit to the channel under test (see Figure 8.1 &
Table 8.1).
2. For multi-channel modules with LFD, connect a 22kΩ resistor across the other channel
input(s) to prevent the signalling of an unwanted open-circuit line fault.
3. Where appropriate test with phase reversal switch in both OFF and ON conditions.
Figure 8.1:
DI input

test circuit

Model Resistor values Switch – simulation conditions

MTL5501-SR R1 = 10kΩ, R2 = 1k4Ω
Table 8.1: a) Normal - field switch open
MTL5510/5510B
Input test MTL5511 b) Normal - field switch closed
conditions MTL5513
R1 = 22kΩ, R2 = 680Ω c) Line Fault - Test for short circuit
MTL5514/5514D
MTL5516C d) Line Fault - Test for open circuit
MTL5517
Output Results
1. For MTL5510 and MTL5510B modules refer to pages 13-15 of this manual.
2. The phase reversal switch will reverse the channel output conditions, but not the LFD.
3. With LFD disabled (OFF) the Status LED should respond as shown in Table 8.2.
4. With LFD disabled (ON) the LEDs and relay should respond as shown in Table 8.3.
Input switch Channel contacts Status

positions NC NO LED
Table 8.2: a Closed Open OFF

Output test
b Open Closed ON
results
c Open Closed ON
d Closed Open OFF
Input switch Channel contacts LEDs LFD relay

positions NC NO Status LFD MTL550x MTL551x
a Closed Open OFF OFF Energised De-energised
b Open Closed ON OFF Energised De-energised
c Closed Open OFF ON De-energised Energised
d Closed Open OFF ON De-energised Energised
60 INM 5500 Rev 10

8.2 Digital Output (DO) modules
Apply tests per channel.
8.2.1 Loop powered: - MTL5521(-T), MTL5522 & MTL5525

Figure 8.2: Loop powered DO test circuit
+
Vs–
V A o/p i/p
– Vs+
1. Connect a voltmeter between the + & – output terminals of the module, observing polarity.
2. Apply 24V between the supply terminals (Vs+, Vs–)
3. The voltmeter should indicate a value between 21.4 and 24 volts
4. Switch off the power to the module
5. Connect an ammeter between the + & – output terminals of the module, observing polarity
6. Apply 24V between the supply terminals (Vs+, Vs–)
7. The ammeter should indicate no more than 70mA for the MTL5522 and no greater than
48mA for any of the other modules
8.2.2 Powered:- MTL5523, MTL5523V, MTL5523VL & MTL5524
Figure 8.3: Powered DO test circuit
MTL5523V/VL
+ + +
V A o/p i/p Control 24V
– – –
1. Connect a voltmeter between the + & – output terminals of the module, observing polarity
2. Apply 24V between the supply terminals Vs+, Vs–
3. The voltmeter should now include no more than 4V
4. Close the Control switch or, for the MTL5523V or MTL5523VL, apply the 24V source
5. The voltmeter should now indicate a value between 21.4 and 24 volts
7. Connect an ammeter between the + & – output terminals of the module, observing polarity
8. Close the Control switch or, for the MTL5523V or MTL5523VL, apply the 24V source
9. The ammeter should indicate no more than 48mA
8.2.3 Relay: - MTL5526

Figure 8.4: DO test circuit for relay type
1. Set in 2-channel mode (SW1 - SW4 respectively to Off, On, On, On)
NO +
NC o/p i/p Control
Common –
2. Confirm continuity between NC and Common

3. Apply 24V between the supply terminals Vs+, Vs–
4. Close the Control switch
5. Confirm continuity between NO and Common
INM 5500 Rev 10 61

8.3 Analogue Input (AI) Modules
All of these tests compare the output current with the input current (A1) over the normal range
of operation, and measure the “error current” i.e. the difference - as indicated on A2. Apply these
tests per channel, as appropriate.
Ammeter A2 must be capable of handling either polarity. If it is not an auto-ranging instrument,

set it to a high range before switch on, then adjust sensitivity to obtain the required reading.
8.3.1 Modules: MTL5541, MTL5544 & MTL55544D

Figure 8.5: AI test circuit #1
Output Measurements
Note: Do not connect a voltmeter in circuit to measure V1 until requested in Step 4 below,
because current measurement A2 could be affected.
1. Adjust RV1 to vary the current (A1) through the range 4 to 20mA
2. The measured current imbalance (A2) over this range should not exceed ± 20µA
3. Adjust RV1 for a 20mA reading on A1
4. The voltage V1, across the channel input, should typically be >16.5V.
8.3.2 Modules: MTL5541S(-T), MTL5544S & MTL5561

– A1
+
+
Ii A2 Io
–
–
24V
RV1
+
10kΩ lin. 250Ω
+ +
V1 i/p o/p
– –
Figure 8.6: AI test circuit #2 “o/p sinking”
Output Measurements
Note: Do not connect a voltmeter in circuit to measure V1 until requested in Step 4 below,
because current measurement A2 could be affected.
1. Adjust RV1 to vary the current (A1) through the range 4 to 20mA.
2. The measured current imbalance (A2) over this range for the MTL5541S and the MTL5544S
should not exceed ± 20µA. For the MTL5561 the imbalance should not exceed ± 400µA.
3. Adjust RV1 for a 20mA reading on A1
4. The voltage V1, across the channel input, should typically be >16.5V.
62 INM 5500 Rev 10

8.3.3 Modules: MTL5541A & MTL5544A

Figure 8.7: AI test circuit #3 “active i/p”
Output Measurements
2. The measured current imbalance (A2) over this range should not exceed ± 20mA
8.3.4 Modules: MTL5541AS & MTL5544AS

Figure 8.8: AI test circuit #4 “active i/p - o/p sinking”
Output Measurements
2. The measured current imbalance (A2) over this range should not exceed ± 20mA
INM 5500 Rev 10 63

8.3.5 Module: MTL5581

Figure 8.9: AI test circuit #5 “mV input”
Note: V1 should be capable of measurement to within 1mV.

Output Measurements
1. With the LINK connected, vary output V2 between 0 and 50mV using RV1. V1 should show
<50mV variation. (Note: Safety Drive can be ON or OFF )
2. With the LINK disconnected and Safety Drive ON, V2 should drive to >+50mV with the
switch set to ‘+’, or <–50mV with the switch set to ‘–’.
8.3.6 Module: MTL5582/5582B
4-wire 5
3-wire
4 9
–
2-wire i/p V 47mV - 2.100V
3
+ 10
+
11
–
– 1 o/p 5.0mA ± 150µA
Resistance
box
12 +
0 - 400Ω min.
Figure 8.10: AI test circuit #5 “Resistance input”
Output Measurements
1. Set Sw1 & Sw2 to ON for 3-wire operation. Set the resistance box to any value between 10
and 400W and switch on power supply.
2. The green PWR LED should go to a steady state after initially flashing. If the flashing does not
stop after 5 seconds then either the setup wiring is faulty or the unit is faulty.
3. Vary the resistance box setting between 10 and 400Ω and confirm the output voltage varies.
4. Short circuit the input and check that the output voltage is ≤ 51.6mV after 5 seconds.
5. Open circuit the input and check that the output voltage is ≤ 2.071V after 5 seconds and that
the green PWR LED is flashing.
6. Set the input resistance to 200Ω and check that the output voltage settles to 1.0V ± 32mV
64 INM 5500 Rev 10

8.4 Analogue Output (AO) Modules
The test compares the output current with the input current over the normal range of operation.
8.4.1 Modules: All variants

Input Conditions
The chosen “load” resistor can be any value between 100 and 800Ω.
– A1 +
Ii A2 Io
+
470Ω
load current
source
–
+ –
o/p i/p
– +
Figure 8.11: AO test circuit
Output Measurements
1. Adjust the current source to vary the current (A1) through the range 4 to 20mA.
2. The measured current imbalance (A2) over this range should not exceed ± 20mA.
8.5 Testing the functioning of other modules

Simple tests to verify their basic operation can be devised for other modules (e.g. temperature,
pulse, vibration, etc). If any assistance is required for the testing of a particular module, please
contact the technical support department at Eaton for advice.
8.5.1 Testing
Make the safe- and hazardous-area connection shown in figure 8.12.
Figure 8.12: Test circuit for MTL5531
Measure the voltage on terminal 3 with respect to terminal 1; this should be >19V. Vary the
potentiometer setting and check that the reading on voltmeter V varies by no more than
±100mV.
INM 5500 Rev 10 65

9 APPLICATIONS INVOLVING ZONE 2 AND/OR ZONE 22
HAZARDOUS AREAS
IMPORTANT: See page iv at the front of this manual for important additional information regarding
the use of these products in countries governed by the ATEX Directive.
The European Community permits Category 3G equipment, such as the MTL5500 , to be installed
in, or connected to, Zone 2 flammable atmospheres provided it meets the requirements of the
ATEX Directive.
MTL5500 Category 3 products have been designed to meet, and carry approval markings for,
Ex nC and/or Ex nA.
In general, meeting the relevant requirements of the appropriate European (CENELEC)

standards is considered the most appropriate method of demonstrating compliance with the
ATEX directive. However, Eaton often has its products approved by other national bodies, such
as FM and CSA and, because national, European, and international standards are converging, it is
generally possible to use other national approvals as supporting evidence for the ATEX Technical
File.
In the context of this document, Zone 2 (Division 2) and Zone 22 hazardous areas are those
that may become potentially explosive through the presence of flammable gases, vapours and
dusts for periods of up to 10 hours per year. It is recommended that the current version of the
standards is consulted for detailed information on the requirements applicable to the particular
installation.
As a consequence of their IS approvals, MTL5500 products may also be connected into Zone 22
hazardous areas. Consult individual module approvals for further details.
Unless otherwise specified, the following ambient conditions apply:
Ambient Temperature range –20°C to +60°C
Pollution Degree 2 (See EN 61010-1)
Measurement Category II (See EN 61010-1)
9.1 Enclosure
EN 60079-15 specifies the minimum required degree of protection to be IP54, but generally this
is provided by the external enclosure in which the product is mounted.
The user must refer to the specific certificates relating to the products being installed within the
hazardous area to check that all special conditions of safe use have been complied with.
66 INM 5500 Rev 10

10 APPENDIX 1
10.1 MTL5000
Many modules in the MTL5000 Isolating Interface Units range have now been superceded
by their equivalent in the MTL5500. For new applications the MTL5500 modules are
recommended, these offer all the benefits of greater efficiency, new multichannel modules
and new functionality.
A number of the products in the MTL5000 will continue to provide key functionality as part of
MTL DIN rail isolator range and are described within this Appendix.
Hazardous-area Non-hazardous
connections (safe) area
connections
115
16.2mm PITCH
104
HAZ SAFE 16
110
Power
connectors
Important
• Make sure that all installation work is carried out in accordance with all relevant local
standards, codes of practice and site regulations.
• When planning the installation of MTL5000 isolators it is essential to make sure that
intrinsically safe and non-intrinsically safe wiring is segregated, and that units are
installed as required by a nationally accepted authority or as described in EN 60079-14, ISA
RP 12.6 or DIN VDE-165.
• Check that the hazardous-area equipment complies with the descriptive system document.
• If in doubt, refer to the certificate/catalogue for clarification of any aspects of intrinsic safety
or contact Eaton’s MTL product line or your local representative for assistance.
• Make sure the correct hazardous-area connector (field-wiring plug) is plugged into the
corresponding isolator. It is recommended that the connector is identified by the same tag
number as the matching isolator.
Mount all MTL5000 isolators on low-profile (7mm) or high-profile (15mm) type T35
(top-hat) DIN-rail to EN50022, BS5584, DIN46277. This is available from Eaton, in 1
metre lengths (THR2 - DIN rail). Install isolators within the safe area unless they are
enclosed in approved flameproof, pressurised or purged enclosures and ensure that
the local environment is clean and free of dirt and dust. Note the ambient temperature
considerations of section 3.1.4.
It is recommended that, in normal practice, the DIN rail should be earthed/grounded

to ensure the safety of personnel in the event of a.c. mains (line) power being applied
accidentally to the rail.
INM 5500 Rev 10 67

10.2 MTL5018AC single-pole, changeover relay,
two-channel, switch/proximity detector with line fault detection
and phase reversal
The MTL5018AC modules enable each of two safe-area loads to be relay-controlled by switches
or proximity detectors in a hazardous area.
Line fault detection (LFD) and output phase reversal facilities are included (see section 6.1).
10.2.1 Wiring connections

See figure 10.1 for wiring connections.
Note: Reactive loads must be adequately suppressed.
10.2.2 Line fault detection

(See section 6.1 for definition of a line fault)
On each channel, input line faults (open- or short-circuit) are indicated by an LED and the
de-energising of the output. LFD is enabled/disabled by switches located on the top of
the module.
Note: that if the LFD facility is enabled for switch inputs, the resistors shown in 10.1 and 10.2
MUST be fitted.
Figure 10.1: MTL5018AC wiring diagram and connections
Terminal Function
2 Input +ve (Ch 1)
3
5 Input +ve (Ch 2)
6
8 Common (Ch 2)
11 Common (Ch 1)
13 Supply N
14 Supply L
68 INM 5500 Rev 10

10.2.3 Testing
Make the safe- and hazardous-area connections shown in figure 10.2, and check the status
of the output contacts for each channel in turn (with a 22kΩ resistor connected to the other
channel) as shown in the table 10.1.
Figure 10.2: Test circuit for MTL5018AC
Table 10.1
Phase Line Input Output Output Channel Line fault

reverse fault switch relay relay status LED LED
switch detection (SW) (11-12, 8-9) (10-11, 7-8) (yellow) (red)
Normal Off a Closed Open On Off
Reverse Off I SC = 7 _ 9mA Open Closed Off Off
Reverse Off Open Closed Open Off Off
Normal On VOC = 7.5 _ 9.5V Open Closed Off On
Normal On a Open Closed Off On
Normal On b Open Closed Off Off
Normal On c Closed Open On Off
INM 5500 Rev 10 69

10.3 MTL5051 serial data comms isolator
The MTL5051provides either bi-directional serial data communications from a computer system
in a safe area to instrumentation in a hazardous area or data communications across
a hazardous area. It is used to provide a fully floating dc supply for, and serial data
communications to MTL640 text displays and MTL650 text and graphics terminals or to other
IS and non-IS instrumentation and keyboards.

See the figures 10.3 and 10.4 and the terminal specifications in tables 10.2 and 10.3 for wiring
connections.
Figure 10.3: MTL5051 wiring diagram (to a hazardous area)
Figure 10.4: MTL5051 wiring diagram (across a hazardous area)
70 INM 5500 Rev 10

10.3.2 Hazardous-area interfacing
Displays/terminals: For details of interfacing with MTL640 and MTL650 displays/terminals (as
an alternative to the MTL696 communications interface) see the appropriate product instruction
manual.
Table 10.2
MTL5051 MTL640 MTL650 Comms Other IS

Terminals mode mode mode devices
1 Common Common Common Common
2 V signal 12V - 5V/12V
3 I return Rx Rx -
4 - Tx Tx -
5 - - - Tx
6 - - - Rx
Switch
1a On Off Off Off
1b On On On Off/On
Table 10.3
Terminals RS232 mode TTL mode RS422 mode

7 - - Rx-
8 - - Rx+
9 - Tx Tx+
10 Tx - Tx-
Figure 10.5: 11 Common Common Common
Top label 12 Rx Rx -
for MTL5051
13 Supply -ve Supply -ve Supply -ve
14 Supply +ve Supply +ve Supply +ve
Switch
2a Off On On
2b On Off Off
Across hazardous areas: For communication across hazardous areas MTL5051 devices are used
in pairs to transfer bi-directional full duplex data across hazardous areas, as shown in figure
10.4. Current switching is used to minimise the bandwidth-limiting effects of long cables.
The maximum baud rate in this mode is the lesser of 19.2k baud or the cable-related rate
produced by the following formula.
Remote signalling baud rate formula, for back-to-back mode across a hazardous area:
max baud rate = K/(RxCxL2)

where K = 0.25 (constant)
R = cable resistance (Ω/m)
C = cable capacitance (F/m)
L = length (m)
For example, with a 2km cable of 100pF/m capacitance and 40mΩ/m resistance, the maximum
baud rate = 0.25/(40mΩ x 100pFx 2km2) = 15k baud. This assumes that the cable is 2 cores
plus screen, with the screen used for the ‘common’ connection.
RS232-level devices: Communication with RS232-level interfaces, such as a suitably certified

IS keyboard, mouse, etc, is achieved by using one or more MTL5051 units as required by the IS
device.(TTL level interfaces are accommodated by the TTL compatibility of RS232 receivers.)
The supply to IS equipment at terminal 2 can be set to either 5V or 12V, by a switch located on
top of the unit, as follows:
+12V mode 12.0V ±5% (load <23mA)
+12V mode 8.0V min (load >23mA to <50mA)
+5V mode5.6V ±5% (load >23mA to <50mA)
Note: the normal RS232 limitations of bandwidth versus cable length are applicable. As a rule
of thumb, speed (baud) x length (metres) <150,000.
INM 5500 Rev 10 71

10.3.3 Testing
Remove all safe- and hazardous-area connections and apply 24V dc to terminals 13 and
14 as shown in figure 10.6. Check that the green power LED (on top of the unit) is on. Put
all switches in the On position. With no load, check for nominal current of 60mA ±5mA at
terminal 14. Correct operation of the communication modes is indicated by signals received
and/or transmitted.
-
dc supply
+
72 INM 5500 Rev 10

10.4 MTL5314 trip amplifier for 2– or 3– wire transmitters
The MTL5314 connects to a 2– or 3– wire 4 to 2mA transmitter or current source located

in the hazardous area. It supplies one or two configurable alarm signals to the safe area via
changeover relays. Each relay may be configured individually to signal an alarm condition when
the input signal is greater than or less than a pre-set value.
In addition, the MTL5314 can be connected in to the hazardous area side of an MTL5042 4 to
20mA repeater power supply (or equivalent device) to provide two trip alarm outputs direct from
the transmitter signal (see schematic diagram). Looping the transmitter signal through the MTL
5314 (via terminals 1 and 3) does not affect HART® communications.
Terminals 1 and 3 meet clause 5.4 of EN50020: 1994 and have the following parameters:
U ≤ 1.5V, I ≤ 0.1A, P ≤ 25mW. They can be connected without further certification into an IS
loop with open circuit voltage of not more than 28V. See certificate for further details.

If terminals 1 and 3 provide a 4 to 20mA loop to a HART transmitter, HART communication can
be superimposed on the 4 to 20mA signal.
Note: Reactive loads must be adequately suppressed.
Figure 10.6: MTL5314 wiring diagram and connections
INM 5500 Rev 10 73

Terminal Function
1 Current input
3 Common
7 Trip B (NC)
8 Trip B (COM)
9 Trip B (NO)
10 Trip A (NC)
11 Trip A (COM
12 Trip A (NO)
13 Supply –ve
14 Supply +ve
10.4.2 Trip calibration

Switches and multiturn potentiometers for setting the trip points are located on top of the unit
(see figure 10.7). For each of channels A and B:
i Set trip switch to H (high) or L (low) as required (see table 10.4

for relay operation).
ii Set input current to the required value for trip-point.
iii Adjust SET A/SET B until LED A/B is on: then slowly adjust until
LED goes out.
iv Relays are energised in normal operation and de-energised when

tripped. A lit LED shows the safe condition (not tripped).
Figure 10.7:
Top label Table 10.4
for MTL5314
Trip Operation PWR A or Relay contacts
switch LED B 11 - 12 10 - 11
A or B LED 8-9 7-8
H (high) Input > trip setting • open closed
H (high) Input < trip setting closed open
L (low) Input > trip setting closed open
L (low) Input < trip setting • open closed
- - • • open closed
74 INM 5500 Rev 10

10.4.3 Testing
Make the safe- and hazardous-area connections shown in figure 10.7 and carry out the
following procedure:
a Set the current source or sink to 12mA
b Adjust each trip potentiometer until the associated LED just

extinguishes.
c With sources of 11.5mA and 12.5mA carry out the following

checks:
Table 10.5
Current High alarm Low alarm

Relay Relay
LED 11 - 12 10 - 11 LED 11 - 12 10 - 11
8-9 7-8 8-9 7-8
11.5mA On closed open Off open closed
12.5mA Off open closed On closed open
INM 5500 Rev 10 75

11 APPENDIX 2:
Table A - Safety descriptions Table B - Maximum cable parameters - IIC gas group
Terminals/ Group/Groupe/Gruppe/Grupo IIC
Terminals/
Bornes/Klemme/ Uo Io Po Bornes/ C L L/R
Model No. Terminales (V) (mA) (mW) Klemme/ (µF) (mH) (µH/Ω)
Model No. Terminales
MTL5501-SR ±9.7 30 70
MTL5501-SR 3.5 39 475
MTL5510 10.5 14 37
MTL5510 2.41 175 983
MTL5510B 10.5 14 37
MTL5510B 2.41 175 983
MTL5511 10.5 14 37
MTL5511 2.41 175 983
MTL5513 10.5 14 37
MTL5513 2.41 175 983
MTL5514 (-T) 10.5 14 37
MTL5514 2.41 175 983
MTL5514D 10.5 14 37
MTL5514D 2.41 175 983
MTL5516C 10.5 14 37
MTL5516C 2.41 175 983
MTL5517 10.5 14 37
MTL5517 2.41 175 983
MTL5521 (-T) 25 147 920
MTL5521 0.11 1.4 40
MTL5522 25 166 1040
MTL5523 0.11 1.4 40
MTL5523 25 147 920
MTL5523V 0.11 1.4 40
MTL5523V 25 147 920
MTL5523VL 0.11 3.04 52
MTL5523VL 25 108 680
MTL5524 0.11 1.4 40
MTL5524 25 147 920
MTL5525 0.11 1.4 40
MTL5525 25 83.3 521
MTL5526 Non-energy storing *
MTL5526 1 a 3, 4 a 6 Non-energy storing *
MTL5531 3a1 0.094 4.02 56
MTL5531 3a1 26.6 94 660
3a2 100 1,000 1,000
3a2 1.1 0.1 0.03
MTL5532 2 a 1, 6 a 1 2.41 181 967
MTL5532 2 a 1, 6 a 1 10.5 14 37
3a1 100 12.6 2,439
3a1 1.1 53 15
4+3a1 0.083 1.66 55
93 @ 28V
4+3a1 28 146 @ 650 5+4a1 0.083 4.02 55
2.9V config † 0.433 60.7 360
5+4a1 28 93 650 3 a 1, 6 a 4 0.094 4.02 56
MTL5533
Uo = 7.2
config † 15 27 3 a 2, 6 a 5 100 1,000 1,000
Ui = 9.1
MTL5533 3 a 1, 6 a 4 26.6 94 660 2 a 1, 5 a 4 0.083 4.2 56
MTL5541 3 a 1, 6 a 4 100 12.8 2,438
3 a 2, 6 a 5 1.1 0.1 0.03 2 a 3, 5 a 6 0.083 5.0 59
MTL5541 28 93 651 MTL5541A 6.2 5.01 1351
MTL5541A 8.6 MTL5541AS 6.2 5.01 1351
– –
MTL5541AS (diode)
MTL5544A 6.2 5.01 1351
MTL5541S (-T) 28 93 651 MTL5544AS 6.2 5.01 1351
MTL5544 28 93 651 MTL5546 0.083 4.2 56
MTL5544A 8.6
– – MTL5546Y 0.083 4.2 56
MTL5544AS (diode)
MTL5549 0.083 4.2 56
MTL5544D 28 93 651
MTL5549Y 0.083 4.2 56
MTL5544S 28 93 651
MTL5561 0.083 4.2 56
MTL5546 28 93 651
MTL5573 1+2+3+4+5+6 22 6.42 288
MTL5546Y (-T) 28 93 651
config † 0.367 153 349
MTL5549 28 93 651
MTL5575 1+2+3+4+5+6 22 6.42 288
MTL5549Y 28 93 651 config † 0.433 153 349
MTL5561 28 93 651 1,2 & 3, 4,5,& 6 11 22.6 384
MTL5576
MTL5573 1+2+3+4+5+6 6.6 76 130 3 a 1, 6 a 4 50 500 1666
3a1 Non-energy storing * config † 0.58 0079.4 448
3,2 & 1 6.6 10 17 100 12.8 2,438
MTL5581
Uo = 8 MTL5582 1,3,4 & 5 22 20.1 513
config † 14.6 26
Ui = 9.1
3a1 100 1,000 3,300
MTL5575 1+2+3+4+5+6 6.6 76 130
1,3, & 4 22 45.3 769
3a1 Non-energy storing *
config † 0.58 79.4 448
3,2 & 1 6.6 10 17
MTL5582B 1,3,4 & 5 22 61.2 894
Uo = 7.2
config † 14.6 26 3a1 100 1,000 3,333
Ui = 9.1
1,3, & 4 22 71.4 966
MTL5576 1,2 & 3, 4,5,& 6 6.6 28 46.2
config † 0.58 79.4 448
3 a1, 6 a 4 Non-energy storing *
config †
Uo = 5.88
12 17.7
Table C - Maximum cable parameters - IIB gas
Ui = 9.1
group
MTL5581 Uo = 1.1 Io = 53
15
Ui = 28 Ii = 120 Group/Groupe/Gruppe/Grupo IIB
Terminals/
MTL5582 1,3,4 & 5 6.6 42 69.3 Bornes/ C L L/R
3a1 Non-energy storing * Klemme/
(µF) (mH) (µH/Ω)
Model No. Terminales
1,3, & 4 6.6 28 46.2
Uo = 5.88 MTL5522 0.84 5.6 132
config † 12 17.7
Ui = 9.1
MTL5582B
* Appareil ne stockant pas d’energies / Betriebsmittel ohne
1,3,4 & 5 6.51 10 16.1
Energiespeicherung / Aparatos que no almacenan energía
3a1 Non-energy storing * (≤ 1,5V; ≤ 0,1A; ≤ 25mW)
1,3, & 4 6.51 6 9.2 † config configuration socket / fiche de configuration / konfigurationssocket
Uo = 5.88 / toma con configuración
config † 12 17.7
Ui = 9.1
76 INM 5500 Rev 10

This page left intentionally blank
INM 5500 Rev 10 77

78 INM 5500 Rev 10

INM 5500 Rev 10 79

AUSTRALIA NORWAY
MTL Instruments Pty Ltd, Norex AS
10 Kent Road, Mascot, New South Wales, 2020, Australia Fekjan 7c, Postboks 147,
Tel: +61 1300 308 374 Fax: +61 1300 308 463 N-1378 Nesbru, Norway
E-mail: [email protected] Tel: +47 66 77 43 80 Fax: +47 66 84 55 33
E-mail: [email protected]
BeNeLux
MTL Instruments BV RUSSIA
Ambacht 6, 5301 KW Zaltbommel Cooper Industries Russia LLC
The Netherlands Elektrozavodskaya Str 33
Tel: +31 (0)418 570290 Fax: +31 (0)418 541044 Building 4
E-mail: [email protected] Moscow 107076, Russia
Tel: +7 (495) 981 3770 Fax: +7 (495) 981 3771
CHINA E-mail: [email protected]
Cooper Electric (Shanghai) Co. Ltd
955 Shengli Road, Heqing Industrial Park SINGAPORE
Pudong New Area, Shanghai 201201 Cooper Crouse-Hinds Pte Ltd
Tel: +86 21 2899 3817 Fax: +86 21 2899 3992 No 2 Serangoon North Avenue 5, #06-01 Fu Yu Building
E-mail: [email protected] Singapore 554911
Tel: +65 6645 9864 / 6645 9865 Fax: +65 6 487 7997
FRANCE E-mail: [email protected]
MTL Instruments sarl,
7 rue des Rosiéristes, 69410 Champagne au Mont d’Or SOUTH KOREA
France Cooper Crouse-Hinds Korea
Tel: +33 (0)4 37 46 16 53 Fax: +33 (0)4 37 46 17 20 7F. Parkland Building 237-11 Nonhyun-dong Gangnam-gu,
E-mail: [email protected] Seoul 135-546, South Korea.
Tel: +82 6380 4805 Fax: +82 6380 4839
GERMANY E-mail: [email protected]
MTL Instruments GmbH,
Heinrich-Hertz-Str. 12, 50170 Kerpen, Germany UNITED ARAB EMIRATES
Tel: +49 (0)22 73 98 12 - 0 Fax: +49 (0)22 73 98 12 - 2 00 Cooper Industries/Eaton Corporation
E-mail: [email protected] Office 205/206, 2nd Floor SJ Towers, off. Old Airport Road,
Abu Dhabi, United Arab Emirates
INDIA Tel: +971 2 44 66 840 Fax: +971 2 44 66 841
MTL India, E-mail: [email protected]
No.36, Nehru Street, Off Old Mahabalipuram Road
Sholinganallur, Chennai - 600 119, India UNITED KINGDOM
Tel: +91 (0) 44 24501660 /24501857 Fax: +91 (0) 44 24501463 Eaton Electric Ltd,
E-mail: [email protected] Great Marlings, Butterfield, Luton
Beds LU2 8DL
ITALY Tel: +44 (0)1582 723633 Fax: +44 (0)1582 422283
MTL Italia srl, E-mail: [email protected]
Via San Bovio, 3, 20090 Segrate, Milano, Italy
Tel: +39 02 959501 Fax: +39 02 95950759 AMERICAS
E-mail: [email protected] Cooper Crouse-Hinds MTL Inc.
3413 N. Sam Houston Parkway W.
JAPAN Suite 200, Houston TX 77086, USA
Cooper Crouse-Hinds Japan KK, Tel: +1 281-571-8065 Fax: +1 281-571-8069
MT Building 3F, 2-7-5 Shiba Daimon, Minato-ku, E-mail: [email protected]
Tokyo, Japan 105-0012
Tel: +81 (0)3 6430 3128 Fax: +81 (0)3 6430 3129
E-mail: [email protected]
EUROPE (EMEA): The given data is only intended as a product

Eaton Electric Limited, description and should not be regarded as a legal
+44 (0)1582 723633
Great Marlings, Butterfield, Luton warranty of properties or guarantee. In the interest
[email protected]
Beds, LU2 8DL, UK. of further technical developments, we reserve the
Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283 right to make design changes.
THE AMERICAS:
E-mail: [email protected] +1 800 835 7075
www.mtl-inst.com [email protected]
© 2017 Eaton
ASIA-PACIFIC:
All Rights Reserved
+65 6 645 9888
Publication No. INM 5500 Rev 10 040517
[email protected]
May 2017

MTL5500 Range: Isolating Interface Units

Uploaded by

Copyright:

Available Formats

MTL5500 Range: Isolating Interface Units

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MTL5500 Range: Isolating Interface Units

Uploaded by

Copyright:

Available Formats

Instruction manual

ii INM 5500 Rev 10

ATEX SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VI

6 UNIT DESCRIPTIONS, SETTING-UP AND CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

(continued on next page)

INM 5500 Rev 10 iii

7 FAULT FINDING AND ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

8 BENCH TESTING MODULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

9 APPLICATIONS INVOLVING ZONE 2 AND/OR ZONE 22 HAZARDOUS AREAS. . . . . . . . . . . . . . . . 66

© 2017 Eaton Electric Limited. All rights reserved.

iv INM 5500 Rev 10

Symbols used on the product and in this manual

INM 5500 Rev 10 v

Special Conditions of Safe Use for Zone 2 applications

vi INM 5500 Rev 10

INM 5500 Rev 10 vii

viii INM 5500 Rev 10

The individual sections of this manual cover the following topics

• Section 2 describes the range

• Section 3 specifies precautions both before and during installation

• Section 4 describes mounting accessories and the power adaptor

• Section 5 discusses the DX range of enclosures

• Section 6 provides relevant technical data

• Section 7 outlines fault-finding and maintenance procedures

• Section 8 describes bench test procedure

• Section 9 provides hazardous-area application information

• Section 10 provides MTL5000 products information

• Section 11 provides safety parameter information

Our latest generation of IS interfaces utilises an innovative “One-Core” technology to ensure

INM 5500 Rev 10 1

Digital Input Channels Function

2 INM 5500 Rev 10

• If in doubt, refer to the certificate/catalogue for clarification of any aspects of intrinsic

Optional TH5000 tag holder for individual

104.8 15.8 +/– 0.2

Top of DIN rail

Figure 3.1: Dimensions of MTL5500 package

It is recommended that, in normal practice, the DIN rail should be earthed/grounded

INM 5500 Rev 10 3

Figure 3.2: Location of switches

3.1.2 Relay outputs

3.1.3 Ambient temperature considerations

3.2 Installing columns of isolators

3.2.1 Mounting isolators on DIN rail

Figure 3.3: DIN rail mounting and removal of isolators

4 INM 5500 Rev 10

Figure 3.4: Removable power and signal plugs

3.2.2.1 Signal and power conductors

3.2.2.2 Making connections

Plug Entry Wire size Metal tube Trim Recommended ferrules

TABLE 3.1: Crimp Ferule Options

INM 5500 Rev 10 5

4.1 MTL5500 power bus - Installation and use

Number of modules Kit ID code

Table 4.1: Power bus kit options

Figure 4.1: Power bus wiring, joining and terminating

6 INM 5500 Rev 10

Direction of Area required

Figure 4.2: MPA5500 AC power adaptor

Figure 4.5: IMB57 Insulating mounting block