Residual Stresses

RESIDUAL STRESSES
Residual stresses are stresses that remain in a solid material after the original cause of the
stresses has been removed. Residual stress may be desirable or undesirable. For example, laser
peening imparts deep beneficial compressive residual stresses into metal components such as
turbine engine fan blades, and it is used in toughened glass to allow for large, thin, crack- and
scratch-resistant glass displays on smartphones. However, unintended residual stress in a designed
structure may cause it to fail prematurely.
TYPES OF RESIDUAL STRESSES
Type-1 Residual Stress
Macro-residual stresses are developed in several grains. Any change in the equilibrium of Type-
1 residual stress will result in a change in macroscopic dimensions. Any treatment or process
which causes inhomogeneous distribution of strains produces Type-1 residual stresses.

Micro-residual stresses are developed in one grain. They can be in different sizes in different
grains. Especially martensitic transformation produces Type-2 residual stress. During the
transformation, incomplete transformation of austenite is observed. The volume of martensite
is larger than that of austenite and this difference forms residual stresses.

Sub-micro residual stresses are developed within several atomic distances of the grain.
Formation is caused by crystalline defects such as vacancies, dislocations, etc.
CAUSES OF RESIDUAL STRESSES
Causes of residual stress
Residual stresses arise whenever a component is stressed beyond its elastic limit and
plastic deformation occurs. Plastic deformation occurs when the stress exceeds a
metal’s yield strength (discussed in Tensile Testing). This can be as a result of…
 Non-uniform plastic deformation during mechanical processing, such as that

during rolling, forming operations (bending or drawing), machining, and
mechanical surface treatments (shot peening and roller burnishing).
 Phase transformations during cooling from elevated temperatures
 Non-uniform plastic deformation during heating or cooling
 Heterogeneity of a chemical or crystallographic order (nitriding or case
hardening)
 Various surface treatments (enameling, electroplating PVD and CVD coating)

Residual stress due to temperature variation

In parts cooled from elevated temperatures, residual stresses are caused by
temperature variations in the metal during
cooling .
Cooling from elevated temperatures occurs during heat treating and welding.
Temperature variations in a metal during cooling from an elevated temperature result in

localized variations of the amount of thermal contraction. Thermal contraction develops
non-uniform stress due to different rates of cooling experienced by the surface and
interior of the metal. During cooling, the outer portion of a component cools first and
that portion of the metal contracts, compressing the hotter inner metal. As the inner
portion of the component cools, the metal tries to contract, but is constrained by the
already cooled outer portion. Consequently, the inner portion will have a residual
tensile stress and the outer portion of the component will have a residual compressive
stress.
Residual stress due to phase transformation
A phase transformation is a change in the metallurgical phases present in an alloy. For

example, the transformation from austenite to martensite in steel during through
hardening is a phase transformation.
Residual stresses that arise during a phase transformation are due to the volume
difference between the newly forming and initial

metallurgical phases. The volume difference causes expansion or contraction of the
metal.
For phase transformations that occur during cooling from an elevated temperature, such
as in steel, the outer portions of the metal cool first and undergo the phase
transformation first. If the volume of the new phase is different from the volume of the
initial phase, then the transformed volume of metal will change as the new phase
forms. As the interior of the metal cools it will also try to increase or decrease in
volume. However, the volume change of the metal interior will be constrained by the
cooler outer layer of metal that has already transformed.
When the volume of the new phase is larger than the volume of the initial phase, the
center portion of the component will be under

compression and the surface will be under tension. When the volume of the new phase
is less than the volume of the initial phase, the center portion of the component will be
under tension and the portion of the metal at and near the surface will be under
compression.
For example, during through hardening of steel during a quench, austenite transforms to
martensite, with the martensite having a volume that is about 4% greater than
austenite. During the quench, the steel at the surface transforms to martensite first
since the surface cools the fastest. As the metal at the interior continues to cool, it
transforms to martensite. However, its volume expansion is restricted by the hardened,
cooler surface layer. This restraint causes the interior to be under compression and the
outer surface under tension (see Metallurgy of Steel Through Hardening).
In some conditions, the volume changes can produce residual stresses large enough to
cause plastic deformation, leading to component warping or distortion. With severe
quenching the quenching stresses can be so large that they cause cracking.
Residual stresses caused by mechanical treatment
Residual stresses also arise when plastic deformation is non-uniform through the cross-
section of an item being deformed such as during bending, drawing, rolling, and
extruding. When a metal undergoes plastic deformation, a portion of the deformation is
elastic (discussed in Tensile Testing). After the load causing the deformation is
removed, the metal tries to recover the elastic portion of the deformation. However, the
elastic recovery is incomplete because it is opposed by the adjacent plastically
deformed material.
Consider a metal item that has been bent. Regions adjacent to the bend will have been
only elastically deformed, and this
region will try to recover, a

phenomenon known as springback. After removing the external force, the regions
which have been bent prevent the adjacent regions from undergoing complete elastic
recovery to the non-deformed condition. These regions are left in a state of residual
tension and the regions which were plastically deformed are in a state of residual
compression.
In general, the sign of the residual stress produced by non-uniform deformation will be
opposite the sign of the plastic deformation which produced the residual stress
Effects of residual stress
Residual stresses can be beneficial or detrimental, depending on whether the stress is

tensile or compressive. Tensile residual stresses can be large enough to cause
component distortion or cracking. Also, fatigue and stress corrosion cracking require
the presence of tensile stresses. Because residual stresses are algebraically summed
with applied stresses, surface residual tensile stresses combined with an applied tensile
stress can reduce the reliability of components. In fact, a residual tensile stress is
sometime sufficient to cause stress corrosion cracking.
Surface residual compressive stresses are generally helpful because they reduce the
effects of applied tensile stresses. In most cases, surface compressive stresses
contribute to the improvement of fatigue strength and resistance to stress-corrosion
cracking.
Controlling residual stress
Controlling the type and magnitude of residual stress is important for applications in
which components will be exposed to fatigue or stress corrosion cracking conditions or
if the residual stresses are large enough to cause component deformation or cracking.
This can be achieved through mechanical treatment, stress relief heat treatment, control
of heat treating processes, and alloy selection.
Mechanical treatments such as shot peening, light cold rolling, stretching, and small
amounts of compressing are used to intentionally induce a compressive residual stress
at the surface of a component.
Because metal yield strength decreases as its temperature increases, metals can be
stress relieved by heating to a temperature where the yield strength of the metal is the
same or less than the magnitude of the residual stress. At this temperature, the metal
can undergo microscopic plastic deformation, thus releasing at least a portion of the
residual stress. After stress relieving, the maximum residual stress that can remain is
equal to the yield strength of the material at the stress-relieving temperature.
From a component processing perspective, residual stresses can be minimized by

using reduced cooling rates to reduce temperature variations and allow for phase
transformations to occur more uniformly throughout a component’s cross-section. Also,
alloys can be selected that alloy for slower cooling rates to be used, while still getting
the desired phase transformations to occur. For example, for carbon steel components
to be through hardened, low-alloy carbon steels enable the use of slower cooling rates
compared to plain carbon steels.

Residual Stresses

Uploaded by

Copyright:

Available Formats

Residual Stresses

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Residual Stresses

Uploaded by

Copyright:

Available Formats

RESIDUAL STRESSES

TYPES OF RESIDUAL STRESSES

Type-1 Residual Stress

Type-2 Residual Stress

Type-3 Residual Stress

CAUSES OF RESIDUAL STRESSES

Causes of residual stress

 Non-uniform plastic deformation during mechanical processing, such as that

Residual stress due to temperature variation

Temperature variations in a metal during cooling from an elevated temperature result in

Residual stress due to phase transformation

A phase transformation is a change in the metallurgical phases present in an alloy. For

difference between the newly forming and initial

center portion of the component will be under

Residual stresses caused by mechanical treatment

region will try to recover, a

Effects of residual stress

Residual stresses can be beneficial or detrimental, depending on whether the stress is

Controlling residual stress

From a component processing perspective, residual stresses can be minimized by

You might also like