INTEGRATED CIRCUITS

DATA SHEET

TSA5511
1.3 GHz Bidirectional I2C-bus
controlled synthesizer
Product specification October 1992
File under Integrated Circuits, IC02
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

FEATURES
• Complete 1.3 GHz single chip system
• Low power 5 V, 35 mA
• I2C-bus programming
• In-lock flag
• Varicap drive disable GENERAL DESCRIPTION

• Low radiation The TSA5511 is a single chip PLL frequency synthesizer

designed for TV tuning systems. Control data is entered
• Address selection for Picture-In-Picture (PIP), DBS via the I2C-bus; five serial bytes are required to address
tuner (3 addresses) the device, select the oscillator frequency, programme the
• Analog-to-digital converter eight output ports and set the charge-pump current. Four
of these ports can also be used as input ports (three
• 8 bus controlled ports (5 for TSA5511T), 4 current general purpose I/O ports, one ADC). Digital information
limited outputs (1 for TSA5511T), 4 open collector concerning those ports can be read out of the TSA5511 on
outputs (bi-directional) the SDA line (one status byte) during a READ operation.
• Power-down flag A flag is set when the loop is “in-lock” and is read during a
READ operation. The device has one fixed I2C-bus
address and 3 programmable addresses, programmed by
APPLICATIONS applying a specific voltage on Port 3. The phase
• TV tuners comparator operates at 7.8125 kHz when a 4 MHz crystal
is used.
• VCR Tuners

ORDERING INFORMATION

EXTENDED TYPE PACKAGE

NUMBER PINS PIN POSITION MATERIAL CODE
TSA5511 18 DIL plastic SOT102(1)
TSA5511T 16 SO plastic SOT109A(2)
TSA5511AT 20 SO plastic SOT163A(3)

Note
1. SOT102-1; 1996 December 5.
2. SOT109-1; 1996 December 5.
3. SOT163-1; 1996 December 5.

October 1992 2
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

QUICK REFERENCE DATA

SYMBOL PARAMETER MIN. TYP. MAX. UNIT

VCC positive supply voltage − 5 − V
ICC supply current − 35 − mA
∆f frequency range 64 − 1300 MHz
VI input voltage level
80 MHz to 150 MHz 12 − 300 mV
150 MHz to 1 GHz 9 − 300 mV
1 GHz to 1.3 GHz 40 − 300 mV
fXTAL crystal oscillator frequency 3.2 4.0 4.48 MHz
IO open-collector output current 10 − − mA
IO current−limited output current − 1 − mA
Tamb operating ambient temperature range −10 − +80 °C
Tstg IC storage temperature range −40 − +150 °C

October 1992 3
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled

TSA5511
synthesizer

Fig.1 Block diagram.

October 1992 4
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

Fig.2 Pin configuration for SOT102. Fig.3 Pin configuration for SOT109.

Fig.4 Pin configuration for SOT163.

October 1992 5
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

PINNING

PIN
SYMBOL DESCRIPTION
SOT102 SOT109 SOT163
PD 1 1 1 charge-pump output
Q1 2 2 2 crystal oscillator input 1
Q2 3 3 3 crystal oscillator reference voltage
n.c. − − 4 not connected
SDA 4 4 5 serial data input/output
SCL 5 5 6 serial clock input
P7 6 6 7 port output/input (general purpose)
n.c. − − 8 not connected
P6 7 7 9 port output/input for general purpose ADC
P5 8 8 10 port output/input (general purpose)
P4 9 9 11 port output/input (general purpose)
P3 10 10 12 port output/input for address selection
P2 11 − 13 port output
n.c. − 11 − not connected
P1 12 − 14 port output
P0 13 − 15 port output
VCC 14 12 16 voltage supply
RFIN1 15 13 17 UHF/VHF signal input 1
RFIN2 16 14 18 UHF/VHF signal input 2 (decoupled)
VEE 17 15 19 ground
UD 18 16 20 drive output

FUNCTIONAL DESCRIPTION
The TSA5511 is controlled via the two-wire I2C-bus. For programming, there is one module address (7 bits) and the R/W
bit for selecting READ or WRITE mode.

WRITE mode : R/W = 0 (see Table 1)

After the address transmission (first byte), data bytes can be sent to the device. Four data bytes are required to fully
program the TSA5511. The bus transceiver has an auto-increment facility which permits the programming of the
TSA5511 within one single transmission (address + 4 data bytes).
The TSA5511 can also be partially programmed on the condition that the first data byte following the address is byte 2
or byte 4. The meaning of the bits in the data bytes is given in Table 1. The first bit of the first data byte transmitted
indicates whether frequency data (first bit = 0) or charge pump and port information (first bit = 1) will follow. Until an
I2C-bus STOP condition is sent by the controller, additional data bytes can be entered without the need to re-address the
device. This allows a smooth frequency sweep for fine tuning or AFC purposes. At power-on the ports are set to the high
impedance state.

The 7.8125 kHz reference frequency is obtained by dividing the output of the 4 MHz crystal oscillator by 512. Because
the input of UHF/VHF signal is first divided by 8 the step size is 62.5 kHz. A 3.2 MHz crystal can offer step sizes of 50 kHz.

October 1992 6
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

Table 1 Write data format

MSB LSB
Address 1 1 0 0 0 MA1 MA0 0 A byte 1
Programmable 0 N14 N13 N12 N11 N10 N9 N8 A byte 2
divider
Programmable N7 N6 N5 N4 N3 N2 N1 N0 A byte 3
divider
Charge-pump 1 CP T1 T0 1 1 1 OS A byte 4
and test bits
Output ports P7 P6 P5 P4 P3 P2* P1* P0* A byte 5
control bits

Note to Table 1
* not valid for TSA5511T
MA1, MA0 programmable address bits (see Table 4)
A acknowledge bit
N14 to N0 programmable divider bits
N = N14 × 214 + N13 × 213 + ... + N1 × 21 + N0
CP charge-pump current
CP = 0 50 µA
CP = 1 220 µA
P3 to P0 = 1 limited-current output is active
P7 to P4 = 1 open-collector output is active
P7 to P0 = 0 outputs are in high impedance state
T1, T0, OS = 0 0 0 normal operation
T1 = 1 P6 = fref, P7 = fDIV
T0 = 1 3-state charge-pump
OS =1 operational amplifier output is switched off (varicap drive disable)

October 1992 7
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

READ mode : R/W = 1 (see Table 2)

Data can be read out of the TSA5511 by setting the R/W bit to 1. After the slave address has been recognized, the
TSA5511 generates an acknowledge pulse and the first data byte (status word) is transferred on the SDA line (MSB first).
Data is valid on the SDA line during a high position of the SCL clock signal.
A second data byte can be read out of the TSA5511 if the processor generates an acknowledge on the SDA line. End of
transmission will occur if no acknowledge from the processor occurs.
The TSA5511 will then release the data line to allow the processor to generate a STOP condition.
When ports P3 to P7 are used as inputs, they must be programmed in their high-impedance state.
The POR flag (power-on reset) is set to 1 when VCC goes below 3 V and at power-on. It is reset when an end of data is
detected by the TSA5511 (end of a READ sequence).
Control of the loop is made possible with the in-lock flag FL which indicates (FL = 1) when the loop is phase-locked. The
bits I2, I1 and I0 represent the status of the I/O ports P7, P5 and P4 respectively. A logic 0 indicates a LOW level and a
logic 1 a HIGH level (TTL levels).
A built-in 5-level ADC is available on I/O port P6. This converter can be used to feed AFC information to the controller
from the IF section of the television as illustrated in the typical application circuit (Fig.5). The relationship between bits
A2, A1 and A0 and the input voltage on port P6 is given in Table 3.
Table 2 Read data format
MSB LSB
Address 1 1 0 0 0 MA1 MA0 1 A byte 1
Status byte POR FL I2 I1 I0 A2 A1 A0 − byte 2

Note to Table 2
POR power-on reset flag. (POR = 1 on power-on)
FL in-lock flag (FL = 1 when the loop is phase-locked)
I2, I1, I0 digital information for I/O ports P7, P5 and P4 respectively
A2, A1, A0 digital outputs of the 5-level ADC. Accuracy is 1/2 LSB (see Table 3)
MSB is transmitted first.

Address selection
The module address contains programmable address bits (MA1 and MA0) which together with the I/O port P3 offers the
possibility of having several synthesizers (up to 3) in one system.
The relationship between MA1 and MA0 and the input voltage I/O port P3 is given in Table 4.

October 1992 8
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

Table 3 ADC levels

VOLTAGE APPLIED ON THE PORT P6 A2 A1 A0

0.6 VCC to 13.5 V 1 0 0
0.45 VCC to 0.6 VCC 0 1 1
0.3 VCC to 0.45 VCC 0 1 0
0.15 VCC to 0.3 VCC 0 0 1
0 to 0.15 VCC 0 0 0

Table 4 Address selection

MA1 MA0 VOLTAGE APPLIED ON PORT P3
0 0 0 to 0.1 VCC
0 1 always valid
1 0 0.4 to 0.6 VCC
1 1 0.9 VCC to 13.5 V

LIMITING VALUES
In accordance with Absolute Maximum Rating System (IEC 134); all pin numbers refer to DIL18 version
SYMBOL PARAMETER MIN. MAX. UNIT
VCC supply voltage −0.3 6 V
V1 charge-pump output voltage −0.3 VCC V
V2 crystal (Q1) input voltage −0.3 VCC V
V4 serial data input/output voltage −0.3 6 V
V5 serial clock input voltage −0.3 6 V
V6-13 P7 to P0 input/output voltage −0.3 +16 V
V15 prescaler input voltage −0.3 VCC V
V18 drive output voltage −0.3 VCC V
I6-9 P7 to P4 output current (open collector) −1 15 mA
I4 SDA output current (open collector) −1 5 mA
Tstg IC storage temperature range −40 +150 °C
Tj maximum junction temperature − 150 °C

THERMAL RESISTANCE

SYMBOL PARAMETER THERMAL RESISTANCE

Rth j-a from junction to ambient in free air
DIL18 80 K/W
SO16 110 K/W
SO20 80 K/W

October 1992 9
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

CHARACTERISTICS
VCC = 5 V; Tamb = 25 °C, unless otherwise specified
All pin numbers refer to DIL18 version
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Functional range
VCC supply voltage range 4.5 − 5.5 V
Tamb operating ambient −10 − +80 °C
temperature range
f input frequency 64 − 1300 MHz
N divider 256 − 32767
ICC supply current 25 35 50 mA
fXTAL crystal oscillator frequency crystal series resonance 3.2 4.0 4.48 MHz
range resistance ≤ 150 Ω
ZI input impedance (pin 2) −480 −400 −320 Ω
input level VCC = 4.5 V to 5.5 V;
Tamb = −10 to +80 °C;
see typical sensitivity
curve Fig.6
f = 80 to 150 MHz 12/−25 − 300/2.6 mV/dBm
f = 150 to 1000 MHz 9/−28 − 300/2.6 mV/dBm
f = 1000 to 1300 MHz 40/−15 − 300/2.6 mV/dBm
RI prescaler input resistance − 50 − Ω
(see Fig.7)
CI input capacitance − 2 − pF
Output ports (current-limited) P0 to P3
ILO output leakage current VO = 13.5 V − − 10 µA
Isink output sink current VO = 12 V 0.7 1.0 1.5 mA
Output ports (open collector) P4 to P7 (see note 1)
ILO output leakage current VO = 13.5 V − − 10 µA
VOL LOW level output voltage IOL = 10 mA; note 2 − − 0.7 V
Input port P3
IOH HIGH level input current VOH = 13.5 V − − 10 µA
IOL LOW level input current VOL = 0 V −10 − − µA
Input ports P4, P5 and P7
VIL LOW level input voltage − − 0.8 V
VIH HIGH level input voltage 2.7 − − V
IIH HIGH level input current VIH = 13.5 V − − 10 µA
IIL LOW level input current VIL = 0 V −10 − − µA
Input port P6
IIH HIGH level input current VIH = 13.5 V − − 10 µA
IIL LOW level input current VIL = 0 V −10 − − µA

October 1992 10
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled

TSA5511
synthesizer

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

SCL and SDA inputs
VIH HIGH level input voltage 3.0 − 5.5 V
VIL LOW level input voltage − − 1.5 V
IIH HIGH level input current VIH = 5 V; VCC = 0 V − − 10 µA
VIH = 5 V; VCC = 5 V − − 10 µA
IIL LOW level input current VIL = 0 V; VCC = 0 V −10 − − µA
VIL = 0 V; VCC = 5 V −10 − − µA
Output SDA (pin 4; open collector)
ILO output leakage current VO = 5.5 V − − 10 µA
VO output voltage IO = 3 mA − − 0.4 V
Charge-pump output PD (pin 1)
IOH HIGH level output current CP = 1 90 220 300 µA
(absolute value)
IOL LOW level output current CP = 0 22 50 75 µA
(absolute value)
V1 output voltage in-lock 1.5 − 2.5 V
I1leak off-state leakage current T0 = 1 −5 − 5 nA
Operational amplifier output UD (test mode T0 = 1)
V18 output voltage VIL = 0 V − − 100 mV
V18 output voltage when OS = 1; VIL = 2 V − − 200 mV
switched-off
G operational amplifier current OS = 0; VIL = 2 V; 2000 − −
gain; I18 = 10 µA
I18/(I1 - I1leak)
Notes to the characteristics
1. When a port is active, the collector voltage must not exceed 6 V.
2. Measured with a single open-collector port active.

October 1992 11
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled

TSA5511
synthesizer

Fig.5 Typical application (DIL18).

October 1992 12
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

Fig.6 Prescaler typical input sensitivity curve; VCC = 4.5 to 5.5 V; Tamb = −10 to +80 °C.

Fig.7 Prescaler Smith chart of typical input impedance; VCC = 5 V; reference value = 50 Ω.

October 1992 13
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

FLOCK FLAG DEFINITION (FL)

When the FL flag is 1, the maximum frequency deviation (∆f) from stable frequency can be expressed as follows:

∆f = ± ( K VCO ⁄ K O ) × I CP × ( C1 + C2 ) ⁄ ( C1 × C2 )

Where:
KVCO = oscillator slope (Hz/V)
ICP = charge-pump current (A)
KO = 4 × 10E6
C1 and C2 = loop filter capacitors (see Fig.8)

Fig.8 Loop filter.

FLOCK FLAG APPLICATION

• KVCO = 16 MHz/V (UHF band)
• ICP = 220 µA
• C1 = 180 nF
• C2 = 39 nF
• ∆f = ± 27.5 kHz.
Table 5 Flock flag settings
MIN. MAX. UNIT
Time span between actual phase lock and FL-flag setting 1024 1152 µs
Time span between the loop losing lock and FL-flag resetting 0 128 µs

October 1992 14
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

PACKAGE OUTLINES

DIP18: plastic dual in-line package; 18 leads (300 mil) SOT102-1

D ME
seating plane

A2 A

A1
L

c
Z e w M
b1
(e 1)
b b2
18 10 MH

pin 1 index
E

1 9

0 5 10 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

UNIT
A A1 A2
b b1 b2 c D (1) E (1) e e1 L ME MH w Z (1)
max. min. max. max.
1.40 0.53 1.40 0.32 21.8 6.48 3.9 8.25 9.5
mm 4.7 0.51 3.7 2.54 7.62 0.254 0.85
1.14 0.38 1.14 0.23 21.4 6.20 3.4 7.80 8.3

inches 0.055 0.021 0.055 0.013 0.86 0.26 0.15 0.32 0.37
0.19 0.020 0.15 0.10 0.30 0.01 0.033
0.044 0.015 0.044 0.009 0.84 0.24 0.13 0.31 0.33

Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC EIAJ PROJECTION

93-10-14
SOT102-1
95-01-23

October 1992 15
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

D E A
X

y HE v M A

16 9

Q
A2
(A 3) A
A1
pin 1 index
θ
Lp

1 8 L

e w M detail X
bp

0 2.5 5 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A
UNIT max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) θ

0.25 1.45 0.49 0.25 10.0 4.0 6.2 1.0 0.7 0.7
mm 1.75 0.25 1.27 1.05 0.25 0.25 0.1 o
0.10 1.25 0.36 0.19 9.8 3.8 5.8 0.4 0.6 0.3 8
0.010 0.057 0.019 0.0100 0.39 0.16 0.244 0.039 0.028 0.028 0o
inches 0.069 0.01 0.050 0.041 0.01 0.01 0.004
0.004 0.049 0.014 0.0075 0.38 0.15 0.228 0.016 0.020 0.012

Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC EIAJ PROJECTION

95-01-23
SOT109-1 076E07S MS-012AC
97-05-22

October 1992 16
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled synthesizer TSA5511

SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1

D E A
X

c
y HE v M A

20 11

Q
A2 A
A1 (A 3)

pin 1 index
θ
Lp
L

1 10 detail X
e w M
bp

0 5 10 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A
UNIT max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z
(1)
θ

0.30 2.45 0.49 0.32 13.0 7.6 10.65 1.1 1.1 0.9
mm 2.65 0.25 1.27 1.4 0.25 0.25 0.1
0.10 2.25 0.36 0.23 12.6 7.4 10.00 0.4 1.0 0.4 8o
0.012 0.096 0.019 0.013 0.51 0.30 0.419 0.043 0.043 0.035 0o
inches 0.10 0.01 0.050 0.055 0.01 0.01 0.004
0.004 0.089 0.014 0.009 0.49 0.29 0.394 0.016 0.039 0.016

Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC EIAJ PROJECTION

95-01-24
SOT163-1 075E04 MS-013AC
97-05-22

October 1992 17
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled

TSA5511
synthesizer

SOLDERING to the printed-circuit board by screen printing, stencilling or

pressure-syringe dispensing before package placement.
Introduction
Several techniques exist for reflowing; for example,
There is no soldering method that is ideal for all IC thermal conduction by heated belt. Dwell times vary
packages. Wave soldering is often preferred when between 50 and 300 seconds depending on heating
through-hole and surface mounted components are mixed method. Typical reflow temperatures range from
on one printed-circuit board. However, wave soldering is 215 to 250 °C.
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these Preheating is necessary to dry the paste and evaporate
situations reflow soldering is often used. the binding agent. Preheating duration: 45 minutes at
45 °C.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
WAVE SOLDERING
our “IC Package Databook” (order code 9398 652 90011).
Wave soldering techniques can be used for all SO
DIP packages if the following conditions are observed:

SOLDERING BY DIPPING OR BY WAVE • A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave) soldering
The maximum permissible temperature of the solder is technique should be used.
260 °C; solder at this temperature must not be in contact
• The longitudinal axis of the package footprint must be
with the joint for more than 5 seconds. The total contact
parallel to the solder flow.
time of successive solder waves must not exceed
5 seconds. • The package footprint must incorporate solder thieves at
the downstream end.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the During placement and before soldering, the package must
specified maximum storage temperature (Tstg max). If the be fixed with a droplet of adhesive. The adhesive can be
printed-circuit board has been pre-heated, forced cooling applied by screen printing, pin transfer or syringe
may be necessary immediately after soldering to keep the dispensing. The package can be soldered after the
temperature within the permissible limit. adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
REPAIRING SOLDERED JOINTS maximum duration of package immersion in solder is
Apply a low voltage soldering iron (less than 24 V) to the 10 seconds, if cooled to less than 150 °C within
lead(s) of the package, below the seating plane or not 6 seconds. Typical dwell time is 4 seconds at 250 °C.
more than 2 mm above it. If the temperature of the A mildly-activated flux will eliminate the need for removal
soldering iron bit is less than 300 °C it may remain in of corrosive residues in most applications.
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds. REPAIRING SOLDERED JOINTS

SO Fix the component by first soldering two diagonally-

opposite end leads. Use only a low voltage soldering iron
REFLOW SOLDERING (less than 24 V) applied to the flat part of the lead. Contact
Reflow soldering techniques are suitable for all SO time must be limited to 10 seconds at up to 300 °C. When
packages. using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
Reflow soldering requires solder paste (a suspension of 270 and 320 °C.
fine solder particles, flux and binding agent) to be applied

October 1992 18
Philips Semiconductors Product specification

1.3 GHz Bidirectional I2C-bus controlled

TSA5511
synthesizer

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

PURCHASE OF PHILIPS I2C COMPONENTS

Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.

October 1992 19