Fujifilm FinePix S9000 S9500 Service Manual PDF

DIGITAL CAMERA
FinePix S9000/
S9500
SERVICE MANUAL
US/CA/EU/EG/EE/AS/CH/JP-Model
CAUTION
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIG-
NATED AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3 to page 5)
WARNING
THE COMPONENTS IDENTIFIED WITH THE MARK “ ” ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTRICAL SHOCK.
Ref.No.:ZM00604-104
FUJI PHOTO FILM CO., LTD. Printed in Japan 2006.02
FinePix S9000/S9500 Service Manual
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered or poorly 7. CAUTION: FOR CONTINUED
soldered connections. Check the entire board surface PROTECTION AGAINST FIRE
for solder splasher and bridges. HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES 125V
2. Check the interboard wiring to ensure that no wires are FUSE.
“pinched” or contact high-wattage resistors.
2.5A 125V
RISK OF FIRE- ATTENTION: AFIN D'ASSURER
REPLACE FUSE
3. Look for unauthorized replacement parts, particularly AS MARKED UNE PROTECTION
2.5A 125V
transistors, that were installed during a previous repair. PERMANENTE CONTRE LES
Point them out to the customer and recommend their RISQUES D'INCENDIE,
replacement. REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
4. Look for parts which, though functioning, show obvious TYPE 2.5 AMPERES, 125 VOLTS.
signs of deterioration. Point them out to the customer
and recommend their replacement. 8. WARNING:
TO REDUCE THE ELECTRIC
5. Check the B + voltage to see it is at the values SHOCK, BE CAREFUL TO
specified. TOUCH THE PARTS.
WARNING!
6. Make leakage - current measurements to determine HIGH VOLTAGE
that exposed parts are acceptably insulated from the

supply circuit before returning the product to the
customer.
2
RoHS lead-free compliance

Because this product is RoHS lead-free compliant, use the designated after-sales parts and the designated lead-free solder
when performing repairs.
<Background & Overview>

With the exception of parts and materials expressly excluded from the RoHS directive (*1), all the internal connections and
component parts and materials used in this product are lead-free compliant (*2) under the European RoHS directive.
*1: Excluded items (list of the main lead-related items)

• Lead included in glass used in fluorescent tubes, electronic components and cathode-ray tubes
• Lead in high-melting-point solder (i.e. tin-lead solder alloys that contain 85% lead or more)
• Lead in ceramic electronic parts (piezo-electronic devices)
• Mercury contained in fluorescent tubes is also excluded.
*2: Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)
<Reference>
RoHS: The name of a directive issued by the European Parliament aimed at restricting the use of
certain designated hazardous substances included in electrical and electronic equipment.
Designated substances (6): Lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBBs) and
polybrominated diphenyl ether (PBDE)
<Lead-free soldering>
When carrying out repairs, use a designated lead-free solder, bearing in mind the differing work practices for conventional
solder (eutectic) and lead-free solder.
Differences in the soldering work for lead-free and eutectic solder

When the soldering work practices for eutectic solder and lead-free solder are compared, the main differences are as shown
below. In particular, when lead-free solder is used, the solder tends to be less workable than when eutectic solder is used.
Accordingly, the soldering techniques used must take that into account.
Difference Countermeasure
1 The solder starts melting later. The initial melting point of lead-free solder is high, so you
have to get used to it.
2 Poor wetting Move the tip of the soldering iron around to heat the entire
connection to the melting temperature and assist wetting.
3 Solder feed rate is difficult to control. Use the solder (wire) diameter and soldering iron that are
best suited to connection being soldered.
4 Wetting the insides of through holes is especially First apply solder to the area immediately around the
difficult. through hold and then feed the solder into the hole.
5 During repairs (or modifications) removing solder Use a suitable wicking wire (with a suitable method and
from inside through holes is difficult. heating) and a suction tool.
6 There is serious carbonization of the soldering iron. Either put solder onto the soldering iron tip after completing
the work, or turn the iron off frequently.
7 The surface is not glossy. Learn to recognize the appearance of the surface.
3
Setting temperature during lead-free soldering

• Lead-free solder melting temperature
The melting point of eutectic (Sn-Pb) solder is 183°C, while the melting point of lead-free solder (Sn-Ag-Cu) is 30°C higher
at 220°C.
• Soldering iron tip temperature

The temperature setting for the soldering iron used should be such that the tip of the soldering iron is at the correct
bonding temperature for the connection. This temperature is normally set at around 100°C higher than the melting point of
the solder.
However, the actual temperature should take into account the shape and size of the soldering iron tip, the heat tolerance
of the connection and the workability of that temperature.
• Correct bonding temperature

The correct bonding temperature refers not to the temperature of the heat source, but to the bonding temperature that will
give the best bond strength.
Precautions when soldering with lead-free solder

• Soldering iron maintenance
Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to
the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
• Uniform heating of the board and components

To ensure that the lead-free solder wets the entire surface of the pattern and the lands despite its poor wetting
characteristics, you must move the tip of the soldering iron over a wide area to raise the temperature of the entire
connection.
Soldering iron
A soldering iron with a temperature control is best.
4
Solder wire (thread)

Use the lead-free solders specified below.
Solder type: Sn96.5Ag3Cu0.5 (Displayed symbol: SnAgCu)
Wire diameter: 0.6, 0.8 or 1.0 mm
Sample:
lead-free
Wire diameter 0.8mm
Solder type (Displayed symbol)

SnAgCu
Flux
Conventional flux can be used.
Solder application wires (mesh, wicking wire, etc.)

Conventional application wires can be used.
5
CONTENTS FinePix S9000/S9500 Service Manual
CONTENTS
1. General .................................................................. 7 3-7. Mounted Parts Diagrams ................................................ 61
1-1. Product specification ......................................................... 7 3-7-1. CCD FPC ASSY ................................................ 61
1-2. Explanation of Terms ...................................................... 11 3-7-2. ML FPC ASSY .................................................. 61
1-3. Names of External Components ..................................... 12 3-7-3. STSW ASSY ..................................................... 61
3-7-4. DCST PWB ASSY ............................................. 62
2. Disassembly ......................................................... 14 3-7-5. MAIN PWB ASSY ............................................. 64
2-1. Names of internal Components ...................................... 14 3-7-6. KEY PWB ASSY ............................................... 66
2-2. Removing the CONST CASE TOP ................................. 15 3-7-7. LED PWB ASSY ............................................... 68
2-3. Disassembling the CONST CASE TOP .......................... 17 3-7-8. TOP FPC ASSY ................................................ 69
2-4. Removing the CASE R CONST ...................................... 18 3-7-9. TRG PWB ASSY ............................................... 69
2-5. Disassembling the CASE R CONST CASE .................... 21
2-6. Removing the HINGE CONST ........................................ 23 4. Adjustments ......................................................... 70
2-7. Removing the MAIN PWB ASSY/DCST PWB ASSY ...... 25 4-1. Important point Adjustment when
2-8. Removing the FRAME PWB/FRAME BATT ................... 29 Replacing Major Parts ..................................................... 70
2-9. Disassembling the CASE F CONST ............................... 29 4-2. Measuring Instruments Used .......................................... 70
2-10. Removing the AF SENSOR UNIT ................................... 33 4-3. Use Jig list ....................................................................... 70
2-11. Location specifications for sticking on sheets ................. 34 4-4. Calibration method of pattern box ................................... 71
2-11-1. Sticking the SHEET CF to the 4-5. Adjustment software installation ..................................... 71
MAIN PWB ASSY ............................................. 34 4-5-1. Various downloading software decompressions,
2-11-2. Sticking the SHEET EMI TOP to the preservation methods, and notes ......................... 71
PLATE FPC TOP .............................................. 34 4-5-2. Installation of DSC jig driver ............................. 72
2-11-3. Sticking the SHEET EMI SIDE to the 4-5-3. Adjustment software initiation method .............. 72
FRAME PWB .................................................... 35 4-6. Initial Settings of the Adjustment Software ..................... 73
2-11-4. Sticking the SHEET EMI-BASE to the 4-7. Starting the Adjustment Software .................................... 76
FRAME PWB/BASE TRIPOD ........................... 35 4-8. [R] : Flash Memory Reset ............................................... 79
2-11-5. Sticking the SHEET EMI-CD to the 4-9. [F9] : AF-Sensor Adjustment ........................................... 81
CCD FPC .......................................................... 36 4-10. [F4] : CCD Data Input ...................................................... 90
2-11-6. Sticking K TAPE onto the relay PWB ................ 36 4-11. [F6] : AF Lens Data Input ................................................ 92
2-11-7. Sticking K TAPE onto the LCD FPC ................. 37 4-12a. [F5] : CAMERA Adjustment ............................................. 94
2-11-8. Sticking K TAPE onto the SHEET 4-12b. [ S ]: Shading compensation adjustment ........................ 99
EMI-FRAME ...................................................... 37 4-13. [F7] : Flash Adjustment ................................................. 104
2-11-9. Sticking the SHEET EMI-FRAME to the 4-14. [F1] : Battery Voltage Adjustment .................................. 106
FRAME PWB/CCD plate .................................. 38 4-15. [F2] : Mode Dial Adjustment .......................................... 110
2-11-10. Sticking the SHEET GRAPHITE to the 4-16. [F11] : Video Adjustment ............................................... 112
HOLDER LENS/CCD plate ............................... 39 4-17. [F8] : Firmware Download ............................................. 114
2-11-11. Sticking the CUSHION EMI-R to the 4-18. [F12] : End Setting ........................................................ 116
CASE R ............................................................. 40
2-11-12. Sticking the SHEET EMI-R-RIGHT/ 5. Inspection ........................................................... 120
SHEET EMI-R-LEFT to the CASE R ................ 40 5-1. Required Measuring Equipment ................................... 120
2-11-13. Sticking K TAPE to the MAIN PWB ASSY ........ 41 5-2. Connection of Measuring Equipment ............................ 120
5-3. Inspection and Factory Settings ................................... 121
3. Schematics ........................................................... 43 5-4. Resolution Checking ..................................................... 126
3-1. Cautions .......................................................................... 43
3-2. Basic Block Names and Functions ................................. 43 6. Parts List ............................................................ 128
3-3. Description of Main Block Functions ............................... 44 6-1. Packing and Accessories .............................................. 128
3-3-1. Technical Overview ........................................... 44 6-1-1. US-model (FinePix S9000) ............................. 128
3-4. Block Diagram ................................................................. 45 6-1-2. CA-model (FinePix S9000) ............................. 129
3-5. Overall connection Diagram ........................................... 46 6-1-3. EU-model (FinePix S9500) ............................. 130
3-6. Circuit Diagrams ............................................................. 47 6-1-4. EG-model (FinePix S9500) ............................. 131
3-6-1. CAMERA BLOCK ............................................. 47 6-1-5. EE-model (FinePix S9500) ............................. 132
3-6-2. DCDC BLOCK .................................................. 48 6-1-6. AS-model (FinePix S9500) ............................. 133
3-6-3. KEY BLOCK ...................................................... 49 6-1-7. CH-model (FinePix S9500) ............................. 134
3-6-4. LCD/EVF BLOCK ............................................. 50 6-1-8. JP-model (FinePix S9000) .............................. 135
3-6-5. PROCESS BLOCK ........................................... 51 6-2. Cabi Front Block ........................................................... 136
3-6-6. AUDIO BLOCK ................................................. 53 6-2-1. US-model (FinePix S9000) ............................. 136
3-6-7. CCD FPC BLOCK ............................................. 54 6-2-2. CA-model (FinePix S9000) ............................. 137
3-6-8. IPS2 BLOCK ..................................................... 55 6-2-3. JP-model (FinePix S9000) .............................. 138
3-6-9. MAIN I/F BLOCK ............................................... 56 6-2-4. EU/EG/EE-model (FinePix S9500) ................. 139
3-6-10. MOTOR BLOCK ............................................... 57 6-2-5. AS/CH-model (FinePix S9500) ....................... 140
3-6-11. TOP FPC BLOCK ............................................. 58 6-3. Internal Block ................................................................ 141
3-6-12. STRB BLOCK ................................................... 59 6-3-1. US/CA/JP-model (FinePix S9000) .................. 141
3-6-13. ML FPC BLOCK ................................................ 60 6-3-2. EU/EG/EE/AS/CH-model (FinePix S9500) ..... 142
3-6-14. LED BLOCK ...................................................... 60 6-4. Cabi Rear Block ............................................................ 143
3-6-15. STSW BLOCK .................................................. 60 6-4-1. US/CA/JP-model (FinePix S9000) .................. 143
3-6-16. TRG BLOCK ..................................................... 60 6-4-2. EU/EG/EE/AS/CH-model (FinePix S9500) ..... 144
6-5. Electrical parts ............................................................... 145
7. Appendix ............................................................ 146

7-1. List of Related Technical Updates Issued ..................... 146
6
FinePix S9000/S9500 Service Manual 1. General
1. General
1-1. Product specification
System
Model Digital camera FinePix S9000 / FinePix S9500
Effective pixels 9.0 million pixels
CCD 1/1.6-inch Super CCD HR
Number of total pixels: 9.24 million pixels
Storage media xD-Picture Card (16/32/64/128/256/512 MB/1 GB)
CF card and Microdrive (Compatibility is listed on Fujifilm website:
http://home.fujifilm.com/products/digital/)
File format Still image: DCF-compliant
Compressed: Exif ver.2.2 JPEG, DPOF-compatible
Uncompressed: CCD-RAW (RAF)
* Design rule for Camera File System compliant DPOF compatible
Movie: AVI format, Motion JPEG
Audio: WAVE format, Monaural sound
Number of recorded pixels Still image: 3488 × 2616 pixels/3696 × 2464 pixels/2592 × 1944pixels/
2048 × 1536 pixels/1600 × 1200 pixels/640 × 480pixels ( / / / / / )
Lens Fujinon 10.7× optical zoom lens
F2.8-F4.9
Focal length f=6.2 mm-66.7 mm
(Equivalent to approx. 28 mm-300 mm on a 35 mm camera)
Digital zoom Approx. 2× (10.7× optical zoom lens is used together: Max. zoom scale: 21.4×)
Aperture (Wide-angle) F2.8 to F11 Up to 13 steps in 1/3 EV increments Manual/Auto selectable
Focal range Normal: Wide-angle: approx. 50 cm (1.6 ft.) to infinity (In High-speed shooting mode:
approx. 2 m (6.6 ft.) to infinity)
Telephoto: approx. 2 m (6.6 ft.) to infinity (In High-speed shooting mode: approx.
4 m (13.1 ft.) to infinity)
Macro: Wide-angle: approx. 10 cm (3.9 in.) to 3 m (9.8 ft.)
Telephoto: approx. 90 cm (3.0 ft.) to 3 m (9.8 ft.)
Super macro: approx. 1 cm to 1 m (0.4 in. to 3.3 ft.) (Wide-angle only)
Sensitivity AUTO/Equivalent to ISO 80/100/200/400/800/1600
Photometry TTL 256-zones metering Multi, Spot, Average
Exposure control Program AE ( , , , , , , P), Shutter-priority AE, Aperture-priority AE, Manual
exposure
Scene position (Anti-blur), (Natural light), (Portrait), (Landscape), (Night)
Exposure compensation -2 EV to +2 EV in 1/3 EV-step increments (P, S, A)
Shutter speed , , , , : 1/4 sec. to 1/4000 sec.
: 4 sec. to 1/500 sec.
P/S/A: 4 sec. to 1/4000 sec. M: 30 sec. to 1/4000 sec.
Bulb (Up to 30 sec.)
Continuous shooting Top 4-frame: Number of recorded frames: up to 4 frames (Max. 1.5 frames/sec.)
Final 4-frame:Number of recorded frames:
last 4 frames before releasing the shutter button (Max. 1.5 frames/sec.)
Long-period continuous shooting mode:
Number of recorded frames: up to 40 frames. (Max. 1.1 frames/sec.)
Auto bracketing ± 1/3 EV, ± 2/3 EV, ± 1 EV
Focus Mode: Auto focus, Continuous AF, Manual focus
AF system: TTL contrast-type
AF frame selection: AF (CENTER), AF (MULTI), AF (AREA)
7
1. General FinePix S9000/S9500 Service Manual
System
White balance Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight), Fluorescent
(Warm White), Fluorescent (Cool White), Incandescent/Custom white balance (2 types))
Self-timer Approx. 10 sec./2 sec.
Flash type Auto flash
Effective range ( :AUTO): Wide-angle: approx. 30 cm-5.6 m (1.0 ft.-18.4 ft.)
Telephoto: approx. 60 cm-3 m (2.0 ft.-9.8 ft.)
Flash mode Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash, Slow Synchro,
Red-Eye Reduction + Slow Synchro
Viewfinder 0.44 inches, 235,000 pixels, LCD viewfinder Approx. 100% coverage
LCD monitor 1.8 inches, Aspect ratio: 4:3; approx. 118,000 pixels low-temperature polysilicon TFT,
Approx. 100% coverage
Movie 640 × 480 pixels/320 × 240 pixels ( / )
(30 frames per second with monaural sound)
A series of continuous image can be recorded up to available recording time per media.
Photography functions High-speed shooting, Best framing, Post shot assist window,
Frame No. memory
Playback functions Trimming, Image rotate, Automatic playback, Multi-frame playback, Sorting by date,
Voice memo
Other functions PictBridge, Exif print, Language (English, Francais, Deutsch, , Italiano, , ),
Time difference, FinePix photo mode ( -mode)
Input/Output Terminals
A/V OUT NTSC/PAL-type (with monaural sound)
(Audio/Visual output)
Digital input/output USB2.0 High-Speed
DC input socket AC Power Adapter AC-5VX (sold separately)
Accessory shoe Hot shoe
Synchronizing terminal Equipped with ISO 519 synchronizing terminal as standard, lock screw provided
Standard number of available frames/recording time per media

The number of available frames, recording time or file size varies slightly depending on the subjects photographed. Note also that
the divergence between standard number of frames and the actual number of frames is greater for medias with higher capacities.
When used media is 4GB or more, a movie up to 60 minutes long (at the “ ” setting) or 120 minutes long (at the “ ” setting)
can be recorded.
Visit website for information on available Microdrive / CompactFlash card: http://home.fujifilm.com/products/digital/
Quality setting F N (30 fps) (30 fps)

Number of recorded pixels 3488 2616 3696 2464 2592 1944 2048 1536 1600 1200 640 480 3488 2616 640 480 320 240
Image data size 4.5 MB 2.2 MB 2.2 MB 1.2 MB 780 KB 630 KB 130 KB 18.8 MB
DPC-16 (16 MB) 3 6 6 12 19 25 122 0 13 sec. 26 sec.
DPC-32 (32 MB) 6 13 13 25 40 50 247 1 27 sec. 54 sec.
DPC-64 (64 MB) 13 28 28 50 81 101 497 3 55 sec. 109 sec.
DPC-128 (128 MB) 28 56 56 102 162 204 997 6 111 sec. 219 sec.
DPC-256 (256 MB) 56 113 113 204 325 409 1997 13 223 sec. 7.3 min.
DPC-512/M512 (512 MB) 113 227 227 409 651 818 3993 27 7.4 min. 14.6 min.
DPC-M1GB (1 GB) 228 456 456 819 1305 1639 7995 54 14.9 min. 29.3 min.
Microdrive 340 MB 77 155 155 279 445 559 2729 18 5.1 min. 10.0 min.
Microdrive 1 GB 234 469 469 842 1313 1642 8212 55 15.3 min. 30.1 min.
8
Power Supply and Others
Power supply Use one of the following:
• 4× AA-size alkaline batteries
• 4× AA-size Ni-MH (Nickel-Metal Hydride) batteries (sold separately)
• AC Power Adapter AC-5VX (sold separately)
Guide to the number of Battery Type Ni-MH batteries
available frames for battery Alkaline batteries
Media 2500 mAh
operation
xD-Picture Card Approx. 140 frames Approx. 340 frames
Microdrive Approx. 100 frames Approx. 320 frames
According to the CIPA (Camera & Imaging Products Association) standard procedure for
measuring digital still camera battery consumption (extract):
When using alkaline batteries, use the batteries supplied with the camera. You can use
Ni-MH batteries also. The storage media should be xD-Picture Card or Microdrive.
Pictures should be taken at a temperature of +23 oC (+73 oF), with the LCD monitor turned
on, AF-assist illuminator off, the optical zoom moved from full wide-angle to full telephoto
(or vice-versa) and back again to its original position every 30 seconds, the flash used at
full power every second shot and the camera turned off and then on again once every 10
shots.
• Note: Because the number of available shots varies depending on the capacity of
alkaline batteries or the level of charge in Ni-MH batteries, the figures shown here
for the number of available shots using batteries are not guaranteed.
The number of available shots will also decline at low temperatures.
Camera dimensions 128.0 mm × 93.0 mm × 129.0 mm/5.0 in. × 3.7 in. × 5.1 in.
(W/H/D) (not including accessories and attachments)
Camera mass (weight) Approx. 645 g/22.8 oz.
(not including accessories, batteries and xD-Picture Card or CF/Microdrive)
Weight for photography Approx. 755 g/26.6 oz. (including batteries and xD-Picture Card)
Operating conditions Temperature: 0 oC to +40 oC (+32 oF to +104 oF)
80% humidity or less (no condensation)
Accessories included z AA-size Alkaline Batteries (LR6) (4)
z 16 MB, xD-Picture Card (1) Anti-static case (1) included
z Strap (1)
z Lens cap (1)
z Lens cap holder (1)
z Lens hood (1)
z A/V cable (1) Approx. 1.2 m (3.9 ft.), plug (2.5 mm dia.) to pin-plug ×2
z USB cable (mini-B) (1)
z CD-ROM (1) Software for FinePix CX
z Owner’s Manual (1)
9
Power Supply and Others

Optional accessories z xD-Picture Card
DPC-16 (16 MB)/DPC-32 (32 MB)/DPC-64 (64 MB)/DPC-128 (128 MB)/
DPC-256 (256 MB)/DPC-512 (512 MB)/DPC-M512 (512 MB)/DPC-M1GB (1 GB)
z AC Power Adapter AC-5VX
z Fujifilm Rechargeable Battery 2HR-3UF
z Fujifilm Battery Charger with Battery BK-NH2 (With Euro type or UK type plug)
z Soft Case SC-FXS9
z Image Memory Card Reader DPC-R1
• Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.2.2) and
models that support USB as standard.
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 4
MB to 128 MB.
z PC Card Adapter DPC-AD
• Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2
MB to 128 MB.
z CompactFlash Card Adapter DPC-CF
• Windows 95/98/98 SE/Me/2000 Professional/XP
• Mac OS 8.6 to 9.2/X (10.1.2 to 10.1.5)
z xD-Picture Card USB Drive DPC-UD1
• Compatible with xD-Picture Card of 16 MB to 512 MB
• Windows 98/98 SE/Me/2000 Professional/XP
• Mac OS 9.0 to 9.2.2/X (10.0.4 to 10.2.6)
10
1-2. Explanation of Terms
Deactivated batteries: Leaving an Ni-MH battery unused in storage for a long period may cause a rise in the level
of substances that inhibit current flow inside the battery and result in a dormant battery. A
battery in this state is referred to as deactivated.
Because current flow is inhibited in a deactivated Ni-MH battery, the battery’s original
level of performance cannot be achieved.
EV: A number denotes Exposure Value. The EV is determined by the brightness of the subject
and sensitivity (speed) of the film or CCD. The number is larger for bright subjects and
smaller for dark subjects. As the brightness of the subject changes, a digital camera
maintains the amount of light hitting the CCD at a constant level by adjusting the aperture
and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when
the light is halved, the EV decreases by 1.
Frame rate (fps): The frame rate refers to the number of images (frames) that are photographed or played
back per second. For example, when 10 frames are continuously photographed in a 1-
second interval, the frame rate is expressed as 10 fps.
For reference, TV images are displayed at 30 fps (NTSC).
JPEG: Joint Photographic Experts Group

A file format used for compressing and saving color images. The higher the compression
rate, the greater the loss of quality in the decompressed (restored) image.
Memory effect: If an Ni-MH battery is repeatedly charged without first being fully discharged, its perfor-
mance may drop below its original level. This is referred to as the “memory effect”.
Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound as a
single file. Images in the file are recorded in JPEG format. Motion JPEG can be played
back by QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs whereby white streaks appear on the image when there
is a very strong light source, such as the sun or reflected sunlight, in the photography
screen.
WAVE: A standard format used on Windows systems for saving audio data. WAVE files have the
“.WAV” file extension and the data can be saved in either compressed or uncompressed
format. Uncompressed recording is used on this camera.
WAVE files can be played back on a personal computer using the following software:
Windows: MediaPlayer
Macintosh: QuickTime Player
* QuickTime 3.0 or later
White Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still looks
white. On the other hand, devices such as digital cameras see a white subject as white by
first adjusting the color balance to suit the color of the ambient light around the subject.
This adjustment is called matching the white balance.
Exif Print: Exif Print Format is a newly revised digital camera file format that contains a variety of
shooting information for optimal printing.
11
1-3. Names of External Components
Power switch Hot shoe AF-assist illuminator

Power-OFF /Self-timer lamp
External AF sensor
Shutter Playback mode
button Photography mode
Release socket
Exposure
compensation button
Flash button
Continuous shooting
button
Command dial Synchronizing terminal
Mode dial
Still photography Movie recording
Manual Anti-blur Movie
Aperture-priority Auto Natural light
Shutter-priority Auto Portrait
Programmed Auto Landscape
Auto Night
AE-L (AE lock) button

Photometry selector dial
Viewfinder (EVF)
EVF/LCD (monitor selector) button
Diopter
adjustment dial Focus check button
Indicator lamp
Strap mount
LCD monitor
Photo mode ( ) button
Slot cover
CF / Microdrive slot
Tripod mount
DISP/BACK button
Battery cover
CF / Microdrive eject
MENU/OK button button
4-direction ( ) button
xD-Picture Card slot
12
Flash
Flash pop-up button Microphone
Strap mount
Focus ring Speaker
Zoom ring INFO (information check)

button
Terminal cover
USB socket (mini-B)
A/V OUT (Audio / Visual output)

Lens hood socket
DC IN 5V (power input) socket
Focus mode selector switch Macro button
(One-touch AF) button
13
2. Disassembly FinePix S9000/S9500 Service Manual
2. Disassembly
2-1. Names of internal Components
HINGE CONST
ASSY CASE R
SPEAKER ASSY
KEY PWB SSSY
FLASH CONST
ASSY CASE TOP
EVF UNIT CONST MAIN PWB SSSY

TOP FPC CONST
AF SENSOR UNIT
FRAME BATT
UNIT BATT HOLDER
AF ILLUMI ASSY
BATTERY LID MIC ASSY

HOLDER LENS
DCST PWB ASSY
FRAME PWB
SW UNIT
BASE TRI POD

ASSY CASE F
COVER JACK
LENS ASSY
14
FinePix S9000/S9500 Service Manual 2. Disassembly
2-2. Removing the CONST CASE TOP
(1) Remove the 2 screws (M1.7 x 5.0).
(2) Press BUTTON FLASH to open the flash.

(3) Place your thumb on the bottom of the DIAL 2
COMMAND on the CONST CASE TOP and push it up 3

in the direction indicated by the arrow.
(4) Release the catch on the left side of the LEVER AE.
15
(5) Pushing the CONST CASE TOP up in the direction of 6

the arrow releases the catch on the front.
(6) This releases the catch on the WINDOW AF side at the
same time.
(7) Remove the TOP FPC in the direction of the arrow.
[Assembly]
Assemble by performing the disassembly procedure in
reverse order.
16
2-3. Disassembling the CONST CASE TOP
(1) Remove the 4 screws (M1.7 x 3.0). 1

(2) Remove the TOP FPC CONST in the direction of the
arrow.
[Assembly]
reverse order. 2
[Notes on assembly]
Assemble with the switch lever set to the OFF position.
(This is to prevent damage to SW851 and SW852.)
17
2-4. Removing the CASE R CONST
(1) Remove the screw (M1.7 x 5.0).


18
(6) Release the PLATE REAR catch and the catch inside
the left side. 6
(7) Slowly pull off the CASE R CONST to the rear.
(8) Remove the SPEAKER ASSY connector.
(9) Remove the SHOE WIRE HARNESS connector.
19
(10) After removing the connectors, remove the LCD FPC

and KEY-MAIN FPC.
(11) Remove the COVER JACK.
[Assembly]
Assemble by performing the disassembly procedure in 11
reverse order.
10
[Notes on assembly]
(1) Ensure that the harness is not pinched in the PLATE
1
REAR during assembly.
(2) Run the SHOE CONST, AF ILLUMI ASSY and FLASH

CONST harness below the FLASH CONST.
2
20
2-5. Disassembling the CASE R
CONST CASE
3
1
(3) Take out the SPEAKER ASSY in the direction of the 5
arrow. (Do not pull the harness.)
2
(4) Remove the KEY PWB ASSY.
(5) Remove the PLATE REAR.
(6) Remove the HINGE CONST.
4
(7) Remove the BUTTON REAR in the direction of the

arrow.
7
[Assembly]
reverse order.
[Notes on assembly]
Assemble with the indicator lug on the LEVER AE
upwards. (This prevents damage to SW750.)
21
[Notes on assembly]
Ensure that the COVER CARD is open when assembling
the KEY PWB. (This prevents damage to SW752.)
[Notes on assembly]
Run the SHOE CONST leads along the PLATE REAR, as
shown in the figure on the right.
22
2-6. Removing the HINGE CONST

(3) Run the LCD FPC to the inside.

(4) Pull the COVER FPC off in the direction of the arrow.
4
(5) Squeeze the catches on the CASE LCD F in the

directions indicated by the arrows and remove.
(6) While squeezing the catches in the directions indicated
by the arrows, remove the case in the direction of the
arrow.
5
6
6
6
5
23
[Assembly] 3
reverse order. 2
3
[Notes on assembly]
To attach the UNIT HINGE to the CASE LCD R. 1
(1) Engage the catches.
(2) Fit the flexible cable onto the catches.
(3) Use the bosses to position the cable.
3
(4) Install the LCD FPC in the location on the COVER FPC 4
shown in the figure on the right.
CAMERA SIDE LCD SIDE
24
2-7. Removing the MAIN PWB ASSY/DCST PWB ASSY
(1) Remove the WIRE HARNESS.

(2) Remove the FPC.
9
4
(5) Remove the FPC.
(6) Remove the FPC.
(7) Remove the FPC.
(8) Remove the WIRE HARNESS. 8 1 2 3
(9) Remove the EVF UNIT CONST in the direction of the 5
arrow. 7 6
If you are removing the WIRE HARNESS for the

FLASH, take care not to touch the terminals as this
could cause an electric shock.

13
(12) Remove the PLATE GND.
14
(13) Spread open the 2 catches.
11
(14) Lift out the MAIN PWB and DCST PWB set in the
direction of the arrow.
13
12
25
(15) Remove the BATT HOLDER connector.

(16) Remove the SYNCHRO TERMINAL connector.
15 To BATT HOLDER
16 To SYNCHRO
TERMINAL
Take care not to touch the main capacitor terminal as

this could result in an electric shock.
(17) Discharge the main capacitor. (To prevent electric

shock, check that it is fully discharged.)
(18) Remove the connector and disassemble the MAIN 17
PWB ASSY and DCST PWB ASSY.
(19) Remove the connector catches and pull off the FFC.
18
[Assembly] 19
reverse order.
26
[Notes on assembling the MAIN PWB ASSY/DCST PWB ASSY]

If the screw holes in the DC JACK and FRAME are
misaligned as shown in the figure below, the PWB is out of
position.
Misalignment
If this is the case, lifting the DCST PWB ASSY at point (1) 1
will produce a clicking noise.
If you hear a click, reposition the PWB correctly as shown

in the figure below.
Correct alignment
27
[Notes on assembling the WIRE HARNESS for the

FLASH CONST]
(1) To ensure that the harness is not pinched when the
FLASH TOP opens and closes, arrange the wires so
that they form a 4-strand twisted cable.
(2) Twist the harness 2 turns to the left from the correct
position and fasten it to the connector.
(3) Ensure that the harness does not protrude below the
FLASH CONST.
28
2-8. Removing the FRAME PWB/FRAME BATT

1 4
(4) Remove the FRAME BATT.
(5) Pull off the BASE TRIPOD in the direction of the arrow.
(6) Remove the FRAME PWB. 3
2-9. Disassembling the CASE F CONST

(2) Pull off the LENS CONST to the front.
8 4
(3) Open the BATTERY LID. 1

6
(5) Widen the gap between the CASE F and the BATT 9
10
HOLDER.
(6) Pull the UNIT BATT HOLDER off in the direction of the
5
arrow.
(9) Remove the HOLDER LENS.
(10) Remove the STRAP LEFT from the inside.
2 3
(11) Push the catch on the inside of the BUTTON FLASH

in the direction of the arrow.
(12) Pull off the BUTTON FLASH in the direction of the
12
arrow.
11
[Notes on assembly]
Take care not to lose the CSP, which is removed a the
same time.
11
29

14
(14) Pull the FLASH CONST off in the direction of the
arrow.
(16) Pull the SW UNIT off in the direction of the arrow.

(17) Remove the solder on the red SYNCHRO TERMINAL 15
lead and loosen the lock nut. 16
(18) Remove the lock nut and base plate in the direction of
the arrow.
(19) Remove the SYNCHRO TERMINAL itself in the
direction of the arrow.
18
[Assembly]
reverse order. 17
19
30
[Notes on assembly]
(1) Ensure that the GATE section of the BUTTON FLASH
is upwards when assembled.
GATE
(2) When assembling the SW UNIT, set the LEVER

FOCUS to “S” and assemble with the SW UNIT lever
set to the center position.
MF
(3) Run the SYNCHRO TERMINAL harness facing

upwards as shown in the figure on the right. Secure the
base plate facing in the direction shown in the figure on
the right.
31
(4) Ensure that the SYNCHRO TERMINAL harness is not

pinched between the CASE F rib and the BATT
HOLDER.
(5) Run the 2 WIRE HARNESS pairs through the BATT

HOLDER catches as shown in the figure.
32
2-10. Removing the AF SENSOR UNIT
[Notes] SENSOR
ADJUSTER
Hold the base of the AF SENSOR UNIT when working on
it.
Do not touch the sensor or adjuster.
BASE

(2) Pull the unit off in the direction of the arrow.
2
[Assembly]
reverse order.
33
2-11. Location specifications for sticking on sheets

2-11-1. Sticking the SHEET CF to the MAIN PWB ASSY
Stick the sheet in place with the square notches aligned with the slits as shown in the figure.
BB17866-100
2-11-2. Sticking the SHEET EMI TOP to the PLATE FPC TOP
Purpose: To ensure conductivity between the two metal plates
The sheet should not be on top of the positioning bosses.
BB17887-100
The sheet should not cover the DIAL COMMAND hole in the plate.
The top sheet should be aligned with the
left edge of the bottom plate and should
not protrude.
34
2-11-3. Sticking the SHEET EMI SIDE to the FRAME PWB
Fold the sheet into upper and lower halves and ensure that the
sheet does not protrude beyond either of the metal plates.
BB17886-100
Use the center of the SW

UNIT plate as a guide to
lateral positioning. (Ensure
that it does not protrude.)
2-11-4. Sticking the SHEET EMI-BASE to the FRAME PWB/BASE TRIPOD

BB17885-100
Adhesion location
Front-back: The corner where the plate begins

Left-right: The edge of the notch in the plate
35
2-11-5. Sticking the SHEET EMI-CD to the CCD FPC

Purpose: To cover the CCD FPC with a conducting sheet to ensure that it makes contact with the CCD metal backing plate
Pressure must NOT be Fold this section over.

applied to this section. • Make the section
Ensure that the conducting exposed to GND as
sheet does not overlap this large as possible.
section.
• Ensure that it does
Ensure that the sheet not protrude onto the
does not overlap this backing section.
absorbent pad.
Stick the sheet in place

so that it is aligned with
edge of the CCD FPC.
BB17891-100
Stick the sheet so that it
is aligned with the CCD
FPC backing plate.
2-11-6. Sticking K TAPE onto the relay PWB

Purpose: To prevent short-circuits and to lock the connector in place.
Apply the K TAPE (9 x 19 mm) so that it covers and hides all the connector pins.
(Cut a section of ZS00116-100 and apply.)
Apply the tape in a position where it hides all the LENS FPC backing.
K TAPE
36
2-11-7. Sticking K TAPE onto the LCD FPC
Purpose: To protect the LCD FPC
Apply the K TAPE (19 x

23 mm) from a position
no more than 1 mm from The entire tape is folded
this protrusion. back over on both sides.
23mm
ZS00116-100
2-11-8. Sticking K TAPE onto the SHEET EMI-FRAME

Application position
Left-right: Left edge of the metal plate

Up-down: The corner where the plate
begins
BB17892-100
Pressure must NOT be applied to this section.
Overall view
Stick as much of the tape as possible

to the backing plate also (so that it
covers the screw heads).
The tape must not go any further left
than this line.
37
2-11-9. Sticking the SHEET EMI-FRAME to the FRAME PWB/CCD plate

Purpose: To insulate the conducting sheet
Apply the K TAPE (19 x 17 mm) so that the conducting sheet in

this section is completely covered and hidden.
19mm
Secure this section with adhesive.
BB17892-100
38
2-11-10. Sticking the SHEET GRAPHITE to the HOLDER LENS/CCD plate
Purpose: To connect area A and CCD backing plate B with the SHEET GRAPHITE (to release heat from the CCD)
A A
Do not press on this area when applying the sheet (to prevent
B
FPC breakage).
Stick the sheet in place as firmly as possible by pressing with your finger on A and CCD backing plate B.
Apply the SHEET GRAPHITE so that the indentation in the

sheet is aligned with the frame protrusions.
A A
B
Ensure that the SHEET does not overlap the main capacitor
receptacle.
In this area, push the SHEET in so that it goes behind the

FZ06466-100 relay PWB.
39
2-11-11.Sticking the CUSHION EMI-R to the CASE R
BB17881-100
Stick the cushions in place so that they are parallel with the lower
protruding section in both places.
Stick the cushions so that the spacer corners are aligned with the corners of the protruding section.
2-11-12. Sticking the SHEET EMI-R-RIGHT/SHEET EMI-R-LEFT to the CASE R

Purpose: To provide conductivity between the HINGE CONST and PLATE GND
Stick the sheet in place so that it is aligned with the hole

positions and parallel with the cabinet section.
Stick the sheet in place so that there is no slack in this section.
BB17889-100 BB17888-100
40
2-11-13. Sticking K TAPE to the MAIN PWB ASSY
Purpose: To prevent short-circuits with the MAIN PWB ASSY
ZS00116-100
Apply the K TAPE (19 x 19 mm) so that these 3 components are

all covered and hidden.
Apply the tape so that it is aligned with the PLATE GND corner.
Stick the tape down firmly so that there is no looseness in this section also.
41
MEMO
42
FinePix S9000/S9500 Service Manual 3. Schematics
3. Schematics
3-1. Cautions
<Cautions when replacing parts>
• Do not reuse removed parts. Always use new parts.
• Note that the negative side of tantalum condensers is readily damaged by heat.
• Except for chemical condensers and tantalum condensers, voltage is not displayed on condensers with a voltage
resistance of 50V or less.
• Resistors not marked are 1/16W chip resistors.
• KΩ = 1000Ω, MΩ = 1000KΩ
• B characteristics of variable resistors and semi-fixed resistors are not displayed.
3-2. Basic Block Names and Functions

Part name Block name Function
LENS CONST CCD FPC BLOCK CCD Output (IC800)
MAIN PWB ASSY CAMERA BLOCK CCD Output A/D Conversion (IC103)
MOTOR BLOCK Shutter/iris/zoom Drive (IC350)
AUDIO BLOCK Audio IN/OUT(IC500)
LCD/EVF BLOCK LCD/EVF Control, Back Light Control
IPS2 BLOCK Power Control, LED Driver, Flash Charge Control (IC300)
STRB BLOCK Flash Charge
PROCESS BLOCK Image Signal Processing, USB Communications,
System Control (IC204)
MAIN IF BLOCK Connection with the DCST PWB
DCST PWB ASSY DC/DC BLOCK Power Supply Generation (IC600), Power Control
KEY PWB ASSY KEY BLOCK Key SW
TOP FPC ASSY TOP FPC BLOCK Power SW, Release SW, Key SW
43
3. Schematics FinePix S9000/S9500 Service Manual
3-3. Description of Main Block Functions

3-3-1. Technical Overview
The FinePix S9000/S9500 features the newly developed 5th-Generation Super CCD HR sensor, boasting a remarkable 9.0 effective
megapixels, the highest pixel count achieved in a consumer digital camera. You’ll immediately see the benefits: ultra-high-resolution
images filled with detail and stunningly rich texture, even at the largest print sizes. But Real Photo image quality is about more than
resolution. The new Super CCD HR offers high sensitivity with unprecedented image quality thanks to the noise suppression
effectiveness of the new RP Processor. The advantages are real: even at dusk outdoors or in low light indoors, you’re now assured
beautiful photos without tripod or flash, retaining the natural light and atmosphere of the scene.
The newly developed Fujinon 10.7x optical zoom lens offers a focal range equivalent to a 28-300mm zoom on a 35mm camera. From
wide-angle landscape or architectural shots to telephoto portraits or sports shooting, it’s a one-lens solution to all your photographic
needs. This lens employs 13 elements in 10 groups, including one hybrid a spherical element and one glass-molded a spherical
element, as well as advanced Anomalous Dispersion and Extra-low Dispersion glass lenses. This formulation yields unparalleled
optical quality with minimal chromatic aberrations throughout the entire zoom range. The new optical design plus a new movement
system of the lens elements reduce lens size to just 66.9mm in diameter and 80.8mm in length. And newly formulated lens coating
reduces flare and ghosting, common problems with digital cameras, and contributes to superbly natural color balance.
CCD signal processing/Camera circuit section

Analog signals output from the 1/1.6 type Super-CCD Honeycom V HR (IC800), with an effective pixel count of 9.03 mega-
pixels, undergo false color compensation processing, adaptive interpolation processing, amplification (AGC) and signal mixing
inside the CCD signal processing IC “BCS (IC103)” before being converted to 14-bit digital signals (A/D) and sent to the signal
processing LSI “YCS (IC204)”.
The vertical drive IC (IC102) for driving the CCD and the OFD voltage control IC (IC101) are in this block.
Motor Circuit Section

The signal processing LSI “YCS (IC204)” that has received various operating switch commands manages the motor drive IC
(IC350) and controls the AF, SHUTTER and IRIS motors.
Imaging and Signal Processing Section

Input data from the CCD
14-bit digital image data (corresponding to 1H) that has been output from the imaging section (CCD/Camera Block) is sent to the
signal processing LSI “YCS (IC204)”, converted to 32-bit (16-bit x 2) data by the [internal buffer] inside this LSI, and the image
data for one frame (3488 x 2616 pix) is stored temporarily in [SD-RAM]. It is also integrated in the [AUTO operation section]
using the 32-bit the signal processing LSI “YCS (IC204)” image data and sent to the BCS_IC (IC103) to obtain the appropriate
AE/AF/AWB.
Record processing to xD Card
Image data stored in SD-DRAM is sent one frame at a time to the internal [signal processing section] in the signal processing
LSI “YCS (IC204)”. In a process called unpacking, “32-bit to 12-bit conversion” and “pre-processing including digital clamp, white
balance and noise reduction processing, linear matrix processing, gamma correction and R/G/B 14-bit to R/G/B 8-bit
conversion” to “8-bit digital R/G/B signals to Y:Cb:Cr = 4:2:2 YC processing” are implemented in this [signal processing section]
and 8-bit Y/Cb/Cr image data are sent to the [internal buffer].
The “rearrangement of data in a format in which 8-bit Y/Cb/Cr signals are easily compressed” is done in the [internal buffer] and
after passing through the [JPEG operation block] to the [media controller], they are recorded on the xD card.
Reproduction of images from xD card
Compressed image data from the xD card is sent as 8-bit image data to the signal processing LSI “YCS (IC204)” then it is sent
to the [media control section], the [DMA unit] and the SD-DRAM and then it is sent to the [media controller], to the [JPEG
operation section] and to the [signal processing section].
In the [signal processing section], 8-bit Y/Cb/Cr signals are converted to 8-bit R/G/B signals and at the same time, lettering
display signals are weighted and passed through the [LCD controller to the LCD unit and displayed.
Image capture system adjustment data are stored in the Flash ROM.
LCD Unit
Digital signals sent from the signal processing LSI “YCS (IC204)” are passed through the [LCD controller (IC401)] to the LCD
unit.
Power Supply Section

Power supply circuits constructed in the core of the DC IC (IC600) create the following power supplies, which are supplied to
each block.
3.3V [IC202 (PROCESS BLOCK)]
D_3.3V [IC204 (YCS), IC300 (IPS2), IC350 (MOTOR BLOCK),
AD_3.3V [IC204 (YCS), IC207 (VIDEO Drv.), TOP FPC, KEY BLOCK]
AU_3.3V [IC500 (AUDIO)]
CAM3.3V [IC102 (V_Drv), IC103 (BCS)]
xD_3.3V [CN204 (xD CARD CONNECTOR)]
CARD_3.3V [CN205 (MICRO DRIVE CONNECTOR)]
D_5V [IC102 (V_Drv), IC300 (IPS2), LCD/EVF BLOCK]
BL_5V [LCD/EVF BLOCK]
MOT_5V [IC353, IC354 (MOTOR BLOCK)]
CCD_-8V [IC800 (CCD), IC102 (V_Drv)]
CCD_15V [IC800 (CCD), IC102 (V_Drv), IC101 (OFD_Drv)]
1.0V [IC204 (YCS), IC300 (IPS2)]
2.5V [IC204 (YCS)]
D_2.5V [IC204 (YCS)]
LCD_8.5V [LCD/EVF BLOCK]
44
3-4. Block Diagram
MAIN PWB ASSY JTAG
SIP
YCS IC204 FF4193 3.3V Operation CF Card

AF Sensor IST,GS1,GS2,END,S/S,CP Slot Micro Drive
IBFC (50PIN)
AUTO
BCS IC103 AD9996 BCS_RESET RECC
10.7xZOOM LENS HA-CCD xD Card xD PictureCard
DR_SW
IRIS 10Steps MS3931 3.3V Operation CCDIF Slot
O.LPF
1/1.64inch (20PIN)
WIDE/TELE Variable 9.2millon pixels CDS ADC Digital MEDIA
14bit Gain UART EVF BL
VI,HI,ADCK
IC800 YCPRO
TFDC LCD/EVF
Z oom p osi t i on
Focus HP(INT)
Manual Focus
CCD[13-0] Cont. EVF

øV H Drv TG Gray
Cont. øH
(Programble) ENCD EVR CXM4007ER 0.44inch
Pulses Code
V Drv.
CGEN TX49 CPU Core SIO_2 IC401
MD2174 WDT
Motor Drv. IC102
X100 DEBUG I/F
M63062HP SHUT PULSE CSIO
SIO LCD Panel
36.00MHz
7ch 1.8inch
BUS120MHz
96MHz
MOT_CLK(5.0MHz) CX-101F(S)36000KH
USB2.0
USB Jack
IC350 EXT1,2(INT),MOB1,2(TIM) CPU Core
BEEP
PeripheralBUS
MFT BL LED x3
Detect system
Peripheral
OFD BIAS
STRB_SY
NJM2125F SUB ICU

SIO_1 I-cache
I-cache 16k
D-cache VBS_OUTIC207
IC101 X200 8k 8k
48.00MHz ADC
DAC Video
AF assist LED driver Driver AV Jack
CX-101F(S)48000KH
Light LT3465 JPEG
BUS Cont. PORT VIDEO_ON AUDIO_OUT
VCTRL SDRAMC
DMAC
OFD_CONT
LED LED CLKC

X201 IC500 AUDIO IC
SIO_2
IPS2 IC300 FF1194 27.000MHz BU7811KN SPEAKER

AMCLK
STRB-XE 3.3V 2
IS
2
IS
LED CX-101F(S)27000KH AFCLK,ABCLK DA SP_AMP
Drv CTL AADIN
I/O Buffer ADAOUT AD MIC_AMP MIC
AU_CS
STRB IPS_ACT
Power on CTL
AU_MUTE
RESET
RTC Reset B BUS x64
BATT
HOT Shoe SIO_3
Backup
SDRAM
TOP
STRB-C 256Mb x64
X Terminal MODE DIAL
X300 COMMAND DIAL
32.768kHz POWER SW
FC-255 CAM/PB SW
SIO_3
RELEASE SW(S1/S2)
DRIVE
STROB
+/-
A BUS x32
DCST PWB PWCTL 1.0V
3.3V
LDO KEY
DC IN DC/DC Block MB39C006A
FUSE
5V R/L/D/U SW
3.3V IC202 FLASH SDRAM
5V SIDE MODULE OK/BACKDISP SW
DC/DC IC. CCD15V,-8V 32Mb x16 256Mb x32 FMODE SW
AN30211A LCD8.5V
DC/CD CONT IC205 IC203 MF/SAF/CAF SW EVF/LCD SW
BATT. 7ch Etc. INFO SW PinP SW
AAx4 IC600 OPAF SW AEL SW
MACRO SW PHOTOMETRY SW
45
3-5. Overall connection Diagram
46
3-6. Circuit Diagrams
3-6-1. CAMERA BLOCK
47
3-6-2. DCDC BLOCK
48
3-6-3. KEY BLOCK
49
3-6-4. LCD/EVF BLOCK
50
3-6-5. PROCESS BLOCK
51
MEMO
52
3-6-6. AUDIO BLOCK
53
3-6-7. CCD FPC BLOCK
54
3-6-8. IPS2 BLOCK
55
3-6-9. MAIN I/F BLOCK
56
3-6-10. MOTOR BLOCK
57
3-6-11. TOP FPC BLOCK
58
3-6-12. STRB BLOCK
59
3-6-13. ML FPC BLOCK
3-6-14. LED BLOCK
3-6-15. STSW BLOCK
3-6-16. TRG BLOCK
60
3-7. Mounted Parts Diagrams
3-7-1. CCD FPC ASSY 3-7-2. ML FPC ASSY
3-7-3. STSW ASSY
61
3-7-4. DCST PWB ASSY
<SIDE A>
62
<SIDE B>
63
3-7-5. MAIN PWB ASSY
<SIDE A>
64
<SIDE B>
65
3-7-6. KEY PWB ASSY
<SIDE A>
66
<SIDE B>
67
3-7-7. LED PWB ASSY
<SIDE A>
<SIDE B>
68
3-7-8. TOP FPC ASSY
3-7-9. TRG PWB ASSY
69
4. Adjustments FinePix S9000/S9500 Service Manual
Revised: 27. Dec. 2005

4. Adjustments Revised: 11. Nov. 2005
4-1. Important point Adjustment when Replacing Major Parts
Adjust the item shown by ¡ in the table below at the part replacement of LENS ASSY, MAIN PWB, DCST PWB, AF-SENSOR,
FLASH CONST and CONST CASE TOP. (Other part replacements need not be adjusted.)
Replacing parts
LENS ASSY MAIN PWB DCST PWB AF-SENSOR FLASH CONST
Adjustment item
0 Flash memory reset {
1 AF-Sensor adjustment {
2 CCD Data Input { {
3 AF Lens Data Input { {
4a CAMERA adjustment { {
4b Shading compensation adjustment { { {
5 Flash adjustment { { { {
6 Battery adjustment { { {
7 Mode dial adjustment { {
8 Video adjustment { {
9 Firmware download Do not use it until there is an instruction.
10 End setting (Do the end setting when you end the adjustment software when you set the camera to the Jig mode)
4-2. Measuring Instruments Used

Measuring equipment Remarks
Regulated power supply For adjustment
Pattern box PTB450F
Digital voltmeter For Battery adjustment
PC Used for various adjustments and operation checks (PC-AT compatible, Win 98/Me/2000/XP)
Brightness meter LS-110 (Minolta) or equivalent
Color temperature meter Color Meter IIIF (Minolta) or equivalent
Flash meter Used for function checks
4-3. Use Jig list

Pats.No Name Comment
ZJ00006-100 Filter LB140 CAMERA adjustment Common with the DS-30/DS-20/DS-7
ZJ00008-100 Lens holder AF Sensor adjustment Common with the 8mmVTR/MX600
ZJ00287-100 Conversion Lens(900mm) AF Sensor adjustment Common with the FinePixS7000
ZJ00009-100 Stand AF Sensor adjustment Common with the 8mmVTR/MX600
ZJ00254-100 Gray Chart (Reflective type) Flash adjustmen Common with the MX700/MX500
FZ05241-100 USB cable General adjustment Common with the FinePixS7000
ZJ00921-100 FxS9000_9500 W PC Soft Ver.1.00 PC adjustment Win98 / Me / 2000 / XP English OS *1
ZJ00684-100 DSC JIG Driver Install.exe For PC setup Win98 / Me / 2000 / XP English OS *1
ZJ00580-100 Power Cable Jig Battery / Mode dial adjustment
ZJ00611-100 X-Y stage for AF adjustment General adjustment Common with the FinePixM603
ZJ00583-100 Screw Driver (D3LUFX88G (2X20)) General repair Common with the FinePixM603
ZJ00653-100 LB140 filter holder kit for X-Y stage Camera adjustment Common with the FinePixF700
ZJ00650-100 VIDEO adjustment jig Video adjustment Common with the FinePixA310
ZJ00553-100 AF solid chart General adjustment Common with the FinePixS2Pro
ZJ00929-100 CCD data for FinePix S9000_S9500 CCD Data Input New Jig *1
FZ06229-100 Video cable Video adjustment Common with the FinePixA310
FZ03983-100 AC Cable (For EG) Use with VIDEO adjustment jig Common with the FinePixA310 *2
FZ03982-100 AC Cable(For EU) Use with VIDEO adjustment jig Common with the FinePixA310 *2
FZ00330-200 AC Cable (For US/JP) Use with VIDEO adjustment jig Common with the FinePixA310 *2
ZJ00581-100 Discharger Discharge for FLASH UNIT
ZJ00525-100 MACRO CHART Resolution inspection Common with the FinePix A201
ZJ00922-100 S9000/9500 Zoom drive jig Camera / SD. adjustment New Jig
ZJ00923-100 S9000/S9500 AF-1mV Chart AF Sensor adjustment New Jig
ZJ00924-100 S9000/S9500 AF-1mH Chart AF Sensor adjustment New Jig
ZJ00925-100 S9000/S9500 AF-70cm Chart AF Sensor adjustment New Jig
ZJ00930-100 AF Lens data for FinePix S9000_S9500 AF Lens Data Input adjustment New Jig *1
*1: Please downloaded from Web server (http://fujifilm-di.intranets.com/).
*2: Select one the power cable suitable each country.
*3: S9000/9500 Zoom drive jig is a Jig by which the thing that the zoom position match of the shading compensation adjustment
automatically does becomes possible. There is no necessity when shading compensation is adjusted by a manual match.
70
FinePix S9000/S9500 Service Manual 4. Adjustments
4-4. Calibration method of pattern box
< Use the pattern box for CAMERA adjustment >
Turn on the power supply in the pattern box.
Afterwards, wait for about ten minutes so that the source of
Pattern BOX
light may stabilize. (All white)
(1) Brightness:
160±5cd/m2 (with LB140 filter)
No chart, center of pattern box
Minolta brightness meter LS-110 or equivalent LB140
* Calibration method
Place the filter (LB140) against the pattern box. With the
filter (LB140) in contact with the brightness meter, adjust
<Fig. 4-4-1> Calibration method of pattern box
the pattern box brightness to 160±5cd/m2.
(2) Color temperature:aa

6100±50 K (with LB140 filter)
No chart, center of pattern box
Minolta color meter IIIF or equivalent
* Calibration method
Place the filter (LB140) against the pattern box. With the
filter (LB140) in contact with the color temperature meter,
adjust the pattern box color temperature to 6100 ± 50 K.
4-5. Adjustment software installation

4-5-1. Various downloading software decompressions, preservation methods, and notes
The PC adjustment softwares are in a specified Web server,
and both of these are the compression of ZIP form files.
Therefore, after downloading these compression files from
the Web server, the decompression of the file is necessary.
In the decompression software, if the decompression of the
ZIP form can be done, any software is OK.
(Please prepare each one for the decompression software.)
The decompression and the preservation method of the PC
adjustment software and the firmware are described
FxS9000_9500 W PC Soft Ver.1.00 ZJ00921-100.zip
to the following.
* The PC adjustment software decompression and
preservation method.
<Step1>
The sdjustment software is downloaded from WEB, and
software is installed in the PC.
We have uploaded the “PC Adjustment Software <Fig. 4-5-1> Fujifilm-di.intranets Screen
(ZJ00921-100.zip) for “FxS9000_9500_W” on our website:
(http://fujifilm-di.intranets.com/).
My Computer
<Step2>
“ZJ00921-100” is a compression of “ZIP type” file.
3.5inch FD(A:)
The “FxS9000_9500_W” and “SU1740” folder can be done (C:)
by extracting it by “Compression software”.
ZJ00921-100
Copy the “FxS9000_9500_W” and “SU1740” folder to the “C”
drive on the Adjustment PC. FxS9000_9500_W
SU1740
<Fig. 4-5-2>
71
<Step3>
When all the folders have been copied to the C:drive, double- My Computer
click on [C:\ FxS9000_9500_W\ FFW.exe] to start the
3.5inch FD(A:)
adjustment software.
(Note) (C:)
* Specify the preservation drive for C drive if it ZJ00921-100
isdecompression software which can specify the
preservation drive. FxS9000_9500_W
* Similarly, defrost without making a new folder if it is
decompression software which can be defrosted without
SU1740 <Fig. 4-5-3>
making a new folder.
* Defrost simply if the decompression software which you have cannot specify the drive specification and the folder making.
[Caution][Important]
(a) PC adjustment software can not start when there is folder of FxS9000_9500_W in folder named ZJ00921-
100.
Please preserve the folder of FxS9000_9500_W and SU1740 right under C drive.
(b) Please do not change the foldername named FxS9000_9500_W.
PC adjustment software can not start when foldername is changed.
4-5-2. Installation of DSC jig driver

* Since this camera uses the USB for communications with
the personal computer, in order to start the PC adjustment
software, [the DSC jig driver] needs to be installed in the
personal computer beforehand.
* The DSC jig driver is the same as that for the FinePix
S7000, so if this jig driver software is already installed in the
personal computer, it is not necessary to install it.
The procedure is given below.
<Step 1>
DSC jig driver (ZJ00684-100.ZIP) is downloaded from Web
server (http://fujifilm-di.intranets.com/).
<Step 2> <Fig. 4-5-4>

Defrost the downloaded compression software
(1)
<Step 3>
FxS9000_9500_W
Double-click setup.exe in the folder of defrosted ZJ00684-
100 and install Fuji FILM DSC Jig Driver as follows.
<Step 4> FxS9000_9500_W
Install the software in [C:\ProgramFiles\Fjig] according to the

instructions on the PC's screen.
4-5-3. Adjustment software initiation method

When the folder has been copied to the C drive, double-click
on the file C:\FxS9000_9500_W\ffw.exe (Fig.4-5-5) to start FxS9000_9500_W_0.ff
the adjustment software.
<Fig. 4-5-5>
72
4-6. Initial Settings of the Adjustment Software
* The initial settings are already written in the "FFW.ini" file,
therefore perform the following procedure to the letter.
Note that, if you change file names, the software will not
start up.
* The initial settings of steps 3 to 6 are already set in the

"FFW.ini" file. Therefore, you need only to check them.
* Do not rewrite the user program (FxS9000_9500_W_0.ff). If

the program is rewritten, the adjustment software will not
startup.
<Step 1>
Double-click on the "FFW.exe" execute file of the adjustment
software to open the "FinePixS9000_9500_W Adjustment
Software Startup" screen (Fig. 4-6-1). FinePix S9000_9500_W Adjustment Software Start-up Screen
Select [Start] from [Operate] on the FFW Toolbar
—> The adjustment software starts
<Fig. 4-6-1>
<Step 2> (1) (2)

Click on "Settings" ([1] in Fig. 4-6-2) in the menubar of the
startup window.
FxS9000_9500_W_0.ff
Then, select "Mode setting" ([2] in Fig. 4-6-2) from the pull-
down menu that appears.
FinePix S9000_9500_W Adjustment Software Start-up Screen
<Fig. 4-6-2>
73
<Step 3> (2) (1)

Select the "EVR&Comm." tab ([1] in Fig. 4-6-3) in the
"Customize" dialog box that appears.
Set the "EVR&Comm." items as follows.
Item Details
etc (-V2) Check
LANC page Check
<Fig. 4-6-3>
(2)
<Step 4>
Select the "Etc" tab ([1] in Fig. 4-6-4) in the "Customize"
dialog box that appears.
Set the "Etc" items as follows.
Item Details
# of auto measure 0
Change mode Do not check
Use Japanese font Do not check
Don’t show OK NG Check or Do not check
[Note]
If [Disable OKNG display] on the PC screen (Fig. 4-6-4) is <Fig. 4-6-4>
set to OFF, the PC screen displays [OK] if adjustment is OK,
and [NG] if adjustment is NG (either setting is OK).
(1) (2)
<Step 5>
Select the "Hardware" tab ([1] in Fig. 4-6-5) in the
"Customize" dialog box that appears.
Input the values for PI/O port ([2] in Fig. 4-6-5).
PIO 0 10 12 14 16
PIO 1 11 13 15 17
Set the "Hardware" items ([3] in Fig. 4-6-5) as follows.
Item Details
Debug Mode Select [Default]
<Step 6>
Once the above settings have been made, click on "Apply"
(3) (4)
([4] in Fig. 4-6-5) in the "Customize" dialog box to complete
setup. <Fig. 4-6-5>
This applies the setup, therefore setting is unnecessary from
the next time forward.
74
[ Setting when S9000/9500 Zoom drive jig is used ]
If the shading correction is calibrated manually, no zoom drive jig is required.
If no zoom drive jig is connected, leave the [Define (-F)] field blank. (If the [AUTO] setting is used, an error occurs when the
calibration software is launched.)
(1) (2)
<Step 7>
Select the "Compile" tab ([1] in Fig. 4-6-6) in the "Customize"
Set the "Compile" items as follows.
Item Details
Define(-F) AUTO
Compile data Do not check
<Fig. 4-6-6>
<Step 8> (2) (1)

Select the "RS232C" tab ([1] in Fig. 4-6-7) in the "Customize"
Item Details
Port: COMX (Port connected with PC)
Baudrate: 19200
Bytes: 8
Stop: 1
Parity: no
Open when start: Check
<Fig. 4-6-7>
(3)
<Step 9>
Once the above settings have been made, click on "Apply"
([3] in Fig. 4-6-7) in the "Customize" dialog box to complete
setup.
Revised: 11. Nov. 2005
75
4-7. Starting the Adjustment Software

<Step 1>
Double-click on [FFW.EXE] (Fig. 4-5-3) in the folder copied to the C drive (see ‘4-5-1. Various downloading software
decompressions, preservation methods and notes’) to display the adjustment software start-up screen.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
FinePix S9000_9500_W Adjustment Software Start-up Screen
<Fig. 4-7-1>
—> The [Cautions When Using the Adjustment Software] screen appears.
<Step 3>
Cautions When Using the FinePix S9000_9500 Adjustment Software

< Notes for adjustment >
1. The adjustment item is different because of changed parts.

2. Refer to Service Manual for details of a
necessary adjustment after parts replacement.
3. Half rise the CONST CASE TOP
when need to AF-Sensor light adjustment.
4. Use the Power Cable Jig when making adjustment.
5. Set the xD-picture card of 64MB or more
that has been formatted in the camera.
6. Execute the end setting after using the adjustment software.
7. Notes have been described to the service manual besides the
above-mentioned, and advance the adjustment after it refers.
Press the [Enter] key to proceed to the Jig Mode Setup screen.
<Fig. 4-7-2>
—> The [Jig Mode Setup] screen appears.
76
<Step 4>
FinePix S9000_9500_W Adjustment Software

< Camera Jig Mode Setup Procedure >
1. Set the mode to the [AUTO] mode.

2. Open the Card cover.
3. Connect the USB cable.
4. Supply 5.0+-0.1V to the camera using the [DC Jack cable]
as appropriate for the adjustment details.
5. Switch camera power ON while pressing the shutter button.
6. Ensure that the LED is lit.
When steps 1 to 6 are complete, press the [Enter] key on the PC.
<Fig. 4-7-3>
—> The [Firmware version check] screen appears.
<Step 5>
FirmWare = 2.66
Vendor Name =FUJIFILM
Manufacturer =FUJIFILM
ProductName =FinePix S9000
Device Type =CAMERA
SerialNo =592D3832365E0508106921200Z0002
Frame Work =1.00
Please download a new version if it is necessary

to download the firmware.
Advance to the adjustment item selection screen
when press the [Enter] Key of PC.
<Fig. 4-7-4>
—> The [Adjustment Items Select] screen appears.
<Note>
(1) [F1] Battery Adjustment cannot be run unless the Power Cable Jig is used to supply power to the camera.
(2) When new MAIN PWB ASSY is replaced, MAIN PWB ASSY is automatically initialized. At that time, wait for one-two
minutes, and advance the adjustment according to the instruction of the adjustment software.
77
<Step 6>
FinePix S9000_9500_W adjustment item select screen

0. [ R ] : Flash memory reset
*Only use for when the MAIN PWB has been replaced.
1. [ F 9 ] : AF-Sensor Adjustment
2. [ F 4 ] : CCD Data Input
3. [ F 6 ] : AF Lens Data Input
4a. [ F 5 ] : Camera Adjustment
4b. [ S ] : Shading Compensation Adjustment
5. [ F 7 ] : Flash Adjustment
6. [ F 1 ] : Battery Voltage Adjustment
7. [ F 2 ] : Mode Dial Adjustment
8. [ F11 ] : VIDEO Adjustment
9. [ F12 ] : End Setting
[ F 8 ] : Firmware Download
[Execute this item only when
need to change the firmware.]
[ X ] : Restart
FxS9000_9500 W PC Soft Ver.1.00
<Fig. 4-7-5>
<Note>
(1) ‘FxS9000_9500 W PC Soft Ver.1.00’ at the bottom-right of the screen indicates the version number of the adjustment
software.
(2) After running firmware download, other adjustments may be required depending on the content of the download software.
In such cases, the items to be adjusted, and the sequence of adjustment, will be indicated separately.
(3) After starting the adjustment software and beginning communication with the camera, always run End Setting following
adjustment and before returning the camera to the customer. If the End Setting is not run, the PC will not recognize the
camera when the two are connected.
Reason: As the camera will remain in the Jig mode (repair mode), it will not be recognized with the normal camera drivers.
(4) When the adjustment is interrupted after the [X]:Restart key is pushed, it remains about the Jig mode.
78
4-8. [R] : Flash Memory Reset
<Note>
Only reset the flash memory when the MAIN PWB ASSY has been replaced.
When the MAIN PWB ASSY has been replaced, always reset the flash memory before making any other adjustments.
If the flash memory is reset when the MAIN PWB ASSY has not been replaced, all the adjusted data reverts to the default
settings.
In this event, adjust all the settings.
(Excludes firmware downloading.)
After the MAIN PWB ASSY has been replaced, proceeding with other adjustments without first resetting the flash memory
will prevent the successful completion of the adjustments.
(In some cases the camera may be completely disabled.)
If this occurs, set the camera to jig mode again and then reset the flash memory.
<Step 1>
In the adjustment item selection screen, select [R]: Reset flash memory.
-->The flash memory reset confirmation screen appears.
Flash memory reset (EVR)

< Attention >
When the MAIN PWB ASSY has been replaced, always reset
the flash memory before making any other adjustments.
Only reset the flash memory when the MAIN PWB ASSY
has been replaced. If the flash memory is reset when the
MAIN PWB ASSY has not been replaced, all the adjusted data
reverts to the default settings. In this event, adjust all the
settings. (Excludes firmware downloading.)
Enter [RESET] from the PC keyboard.
<Fig. 4-8-1>
-->The [Reconfirm flash memory reset] screen then appears.
79
<Step 2>
Flash memory reset (EVR)

< Attention >
When the MAIN PWB ASSY has been replaced, always reset
the flash memory before making any other adjustments.
Only reset the flash memory when the MAIN PWB ASSY
has been replaced. If the flash memory is reset when the
MAIN PWB ASSY has not been replaced, all the adjusted data
reverts to the default settings. In this event, adjust all the
settings. (Excludes firmware downloading.)
Enter [RESET] from the PC keyboard.
RESET
Input is completed.
Press the "Enter" key to reset the flash memory.
<Fig. 4-8-2>
-->Once the flash memory reset has been completed successfully, the [End flash memory reset] screen appears.
<Step 3>
Flash Memory Reset is completed
(1) Remove the DC jack cable from the camera.

(2) Press the [Enter] key.
<Fig. 4-8-3>
80
4-9. [F9] : AF-Sensor Adjustment
< Setup for AF-Sensor Adjustment>
(1) Prepare as follows using non-defective equipment.
(2) Mount the camera on a tripod, and place the S9000/S9500 AF-1mV Chart (for 1005mm) at a distance of 1005mm from the
front face of the AF-Sensor window.
(3) Set the camera power lever to the Photography mode, and display the through screen on the TV monitor.
(4) Set the lens position to TELE END.
(5) Adjust the camera position so that the AF target symbol (yellow) displayed on the TV monitor overlaps the 'Red circle'
symbol near the center of the 9000/S9500 AF-1mV chart (for 1005mm).
(6) Attach an OHP sheet to the TV monitor.
(7) Place a mark in the center of the target mark displayed on the TV monitor.
(8) Draw a circle on the OHP sheet with the marked point as the center.
The size of the circle will differ from the TV monitor used. The circle sizes for the various TV monitors are as follows.
14" to 16" : 5mm radius
(9) This completes preparations for AF-Sensor Adjustment.
<Environmental Settings for AF-Sensor Adjustment>

(1) Set up the conversion lens (f=900 mm) and the two types of AF-Sensor chart as shown below.
(2) Illuminate the AF-Sensor chart (1000mm) using one or two light sources. Adjustment is impossible if the illumination does
not match.
The distance between the light sources and the AF-Sensor chart must be approximately 5cm.
AF-Sensor chart reflective luminance : 7.0Ev to 9.0Ev
(3) Place the conversion lens concentric with the front face of the AF-Sensor window.
(4) If the center of the conversion lens and the center of the AF-Sensor window are significantly misaligned, an error will occur
during AF-Sensor Adjustment, and adjustment will become impossible.
Front face of Light Sourse

AF sensor window 100mm+-5mm (Fluorescent lamp)
105mm
Top
FinePix S9000/ Bottom

S9500
S9000/S9500 AF-1mV Chart
Adjustment PC f=900mm
Conversion lens Position of f=900mm Conversion Lens
AF Chart
Light Sourse
(700mm)
(Fluorescent lamp)
700mm Adjustment:700mm+-5mm
TV monitor 1000mm Adjustment:1005mm+-5mm
81
<Cautions During Adjustment>

Adjust the AF-Sensor when the AF-Sensor unit detaches or replaces it from the camera.
As the accuracy of AF distance measurement with the AF-Sensor unit changes with temperature, this adjustment
should be performed immediately after the camera power supply is switched ON.
Errors will occur, and adjustment will become impossible, if adjustment is performed after the internal temperature of
the camera has increased to 35°C or more.
If an adjustment error is displayed when the 900mm conversion lens is used, switch camera power OFF, wait, and
perform the adjustment again.
Purpose: Mechanical adjustment in the horizontal and vertical directions of the AF-Sensor (passive) in relation to the optical
axis of the lens assembly.
<Step 1>
Select [F9] from the [Adjustment Items Select Screen]. (press [F9] on the PC keyboard)
--> The [AF-Sensor adjustment Screen (Fig. 4-9-1)] appears.
<Step 2>
AF-Sensor Adjustment
< Adjustment preparation (1) >
Complete the preparation for the AF-Sensor adjustment.
* Refer to the service manual for details.
Remove CONST CASE TOP.

Match the zoom position to a tele end.
* Refer to the service manual for details.
When preparation are complete, Press the [Enter] key.
<Fig. 4-9-1>
When preparations are complete, press the Enter key.

--> The [AF-Sensor vertical Adjustment Screen (Fig. 4-9-2)] appears.
z Revised: 08. Feb. 2006
82
<Step 3>
AF-Sensor vertical Adjustment

(1) Place the S9000/S9500 AF-1mV Chart at a
distance of 1005+-5mm from the Zoom-Ring edge.
(2) Don't set the conversion lens yet.
(3) Match the zoom position to a tele edge.
When preparations (1) - (3) are complete,

press the [Enter] key.
AF-1mV Chart
Zoom Ring edge 1005 +-5mm

| <---------------------------------------Center--------------------------------------->
|
CAMERA = = = < Setup for AF-Sensor V Adjustment >
<Fig. 4-9-2>
--> The [AF-Sensor Sensor vertical Adjustment Screen (Fig. 4-9-3)] appears.
Caution:
When adjusting the camera, measure distance from the front face of the Focus ling.
83
<Step 4>
Adjust the screen angle so that the 'Red circle' symbol displayed on the TV monitor is within the circle.

< Adjustment preparation >
Confirm Red circle of the AF-1mV Chart displayed in the
TV monitor is in the round sign made in the TV monitor.
When preparation is complete, press the [Enter] key.
<Fig. 4-9-3>
--> The [AF-Sensor vertical Adjustment Screen (Fig. 4-9-4)] appears.
Top
Red Symbol
Bottom
S9000/S9500 AF-1mV Chart (1000mm): Expansion
84
<Step 5>
Adjust the AF-Sensor by turning the AF-Sensor Adjustment screw (silver colored) with a + screwdriver in accordance with
the instructions from the adjustment software.

THRE1 = 128
MAX = 171 MAX = 162
MIN = 113 MIN = 117
Turn the AF-Sensor vertica adjustment screw.

Press the [Enter] of PC when the adjustment is completed.
TURN CCW
Press [0]key of PC when you cannot complete the adjustment.
<Fig. 4-9-4>
Turn the adjustment screw while viewing the WAVE No.0 screen to increase the speed of adjustment.
WAVE No.0 screen
Up/Down
Position of AF-Sensor Adjustment Screw
85
When [Adjustment OK!] appears on the screen, press the [Enter] key on the PC and make adjustment preparations in
accordance with the instructions from the adjustment software.
AF-Sensor vertical adjustment

THRE1 = 118
MAX = 96 MAX = 196
MIN = 82 MIN = 92
Turn the AF-Sensor vertical adjustment screw.

OK!
<Fig. 4-9-5>
--> The [AF-Sensor horizontal adjustment Screen (Fig. 4-9-6)] appears.
<Step 6>
AF-Sensor horizontal Adjustment

(1) Change the S9000/S9500 AF-1mH Chart at a
(2) Don't set the conversion lens yet.

AF-1mH Chart
Zoom Ring edge 1005 +-5mm

| <--------------------------------------Center-------------------------------------->
|
CAMERA = = = < Setup for AF-Sensor H Adjustment >
<Fig. 4-9-6>
--> The [AF-Sensor horizontal adjustment Screen (Fig. 4-9-7)] appears.
86
<Step 7>
AF-Sensor horizontal adjustment

THRE1 = 128
MAX = 171 MAX = 162
MIN = 113 MIN = 117
Turn the AF-Sensor horizontal adjustment screw.

TURN CW
<Fig. 4-9-7>
Turn the adjustment screw while viewing the WAVE No.0 screen to increase the speed of adjustment.
WAVE No.0 screen Right/Left
Position of AF-Sensor Adjustment Screw
87
When [Adjustment OK!] appears on the screen, press the [Enter] key on the PC and make adjustment preparations in
accordance with the instructions from the adjustment software.
AF-Sensor horizontal Adjustment

THRE1 = 148
MAX = 199 MAX = 200
MIN = 122 MIN = 162
Turn the AF-Sensor horizontal adjustment screw.

OK!
<Fig. 4-9-8>
--> The [AF-Sensor Linearity adjustment (Fig. 4-9-9)] appears.
<Step 8>
900mm conversion lens setup distance : 105mm+/-5mm from front face of AF-Sensor window.
Chart surface reflective luminance : 7.0Ev to 9.0Ev.
Press the Enter key.
AF-Sensor Linearity adjustment

(1) Set the 900mm conversion lens at a distance of 105+-5mm
z from the Zoom-Ring edge.

< Setup for AF-Sensor linearity Adjustment >

AF-1mL Chart
105 +-5mm
|<-> 1005 +-5mm
| <--------------------------------------Center-------------------------------------->
---Conversion lens
|
CAMERA = = =
< Setup for AF-Sensor L Adjustment >
<Fig. 4-9-9>
--> The [AF-Sensor right and left difference adjustment Screen (Fig. 4-9-10)] appears.
z Revised: 08. Feb. 2006

88
<Step 9>
Remove900mm conversion lens and setup the 700mm Chart distance : 700mm+/-5mm from front face of AF-Sensor
window.
Chart surface reflective luminance : 7.0Ev to 9.0Ev
AF-Sensor right and left difference adjustment

(1) Change the S9000/S9500 AF-70cm Chart at a
(2) Remove the 900mm conversion lens.
When preparations are complete, press the [Enter] key.
AF-70cm Chart
700 +-5mm
| <--------------------------------------Center-------------------------------------->
CAMERA < Setup for AF-Sensor R-L Adjustment >
<Fig. 4-9-10>
--> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
--> The [AF-Assist light adjustment complete Screen (Fig. 4-9-11)] appears.
<Step 10>
The AF-Sensor adjustment is completed.
Press the [Enter] key to return to the

Adjustment Item selection Screen.
<Fig. 4-9-11>
89
4-10. [F4] : CCD Data Input

CCD data input is required when the LENS ASSY or MAIN
PWB ASSY is replaced.
[Method of acquiring CCD data]

05001A0
1. When you exchange LENS ASSY 0179AC
--> It is attached to LENS ASSY.
2. When you exchange MAIN PWB ASSY

--> Creating a CCD data floppy disk when the MAIN PWB
ASSY has been replaced.
* The following example assumes the use of the serial 05001A0
No. shown at right. +0179AC+
<Step 1>
Read the serial number of LENS ASSY.
The numbers shown at right are as follows.
50010179
First line: 05001A0 (seven digits) <Fig. 4-10-1>
Bottom line: +0179AC+ (eight digits)
The name of the CCD data file containing this number is
“50010179.dat”.
* Use the 2-5th digit from the first line. (http://fujifilm-di.intranets.com/)
* Use the 1-4th digit from the Bottom line.
Cautions:
1. The CCD defect data file extension is “dat”.
Depending upon Windows settings, this extension may
not be displayed. In this case, change the settings to
ensure that it is displayed.
2. In addition to numbers, letters are also used in the CCD
serial No. The data file name is instructed in the same
manner in this case.
3. Ensure that the CCD serial No. is read correctly. If the file
name is read incorrectly CCD data for another camera
will be loaded when this file is used.
(3)
<Step 2>
Download the ZIP file of top four digits from Web server
(2)
Open [ZJ00929-100] in the CCD defect data folder, and Data after decompression
CCD Defect Data ZJ00929-100

download “5001.zip”. 5000.zip
50010054
50010089
50010113
<Step 3> 5001.zip 50010128
Decompress “5001.zip”. 50010136

50010152
--> “5001 folders” including “50010179.dat” is made.
(1) 5002.zip
<Step 4> 50010179
Insert a writable floppy disk into the floppy disk drive on the
computer. < Defect data making procedure chart >
<Step 5>
Open in “5001 folders”, search for “50010179.dat”, and copy
it onto the floppy disk.
Caution: Do not create a folder on the floppy disk when

copying the data.
90
< Adjustment >
<Step 1>
Select [F4] CCD Defect Data Input on the [Adjustment Items Select] screen.
--> The [CCD Defect Data Input Start] screen appears.
<Step 2>
50010179
CCD Defect data input

< Preparations >
(1) Enter the 8-digit ccdserial number in the

CCD Data Input dialog box.
The file extrension need not be entered.
(2) Insert the floppy disk
in the A: drive (floppy disk drive) on the PC.
When preparations (1) - (2) are complete, press the [Enter] key on the PC.
( Or, click on the OK button.)
<Fig. 4-10-2>
--> The [CCD Defect Data Input Complete] screen appears.
<Step 3>
CCD Defect data input is completed.

Press the [Enter] key to return
to the Adjustment Item Selection Screen.
<Fig. 4-10-3>
91
4-11. [F6] : AF Lens Data Input

AF lens data input is required when the LENS ASSY or MAIN
PWB ASSY is replaced.
[Method of acquiring AF Lens data]

{The following example assumes the use of the serial No.
shown at right.
Download the AF Lens data from “http://fujifilm-
di.intranets.com/”.
<Step 1>
Read the serial number of LENS ASSY.
Cautions:
101618
1. The AF Lens Data file extension is “csv”.
Depending upon Windows settings, this extension may
not be displayed. In this case, change the settings to
ensure that it is displayed.
2. In addition to numbers, letters are also used in the AF
Lens Data serial No. The data file name is instructed in
the same manner in this case. 101618
3. Ensure that the AF Lens Data serial No. is read correctly.
If the file name is read incorrectly AF Lens Data for
another camera will be loaded when this file is used. <Fig. 4-11-1>
<Step 2>
Download the ZIP file of top four digits from Web server (http://fujifilm-di.intranets.com/)
Open [ZJ00930-100] in the AF Lens Data folder, and
download “101.zip”.
<Step 3>
Decompress “101.zip”.
--> “101 folders” including “101618.csv” is made.
<Step 4>
Insert a writable floppy disk into the floppy disk drive on the
computer.
<Step 5>
(3)
Open in “101 folders”, search for “101618.csv”, and copy it
onto the floppy disk.
(2)
Caution: Do not create a folder on the floppy disk when
copying the data. Data after decompression
AF Lens Data ZJ00930-100

100.zip
100313
100628
100832
101.zip 101047
101254
101389
(1) 102.zip
101618
< Defect data making procedure chart >
{ Revised: 24. Feb. 2006

92
< Adjustment >
<Step 1>
Select [F6] AF Lens Data Input on the [Adjustment Items Select] screen.
--> The [AF Lens Data Input Start] screen appears.
<Step 2>
101618
AF Lens Data Input

< Preparations >
(1) Enter the 6-digit AF serial number in the

AF Lens Data Input dialog box.
The file extrension need not be entered.
(2) Insert the floppy disk
in the A: drive (floppy disk drive) on the PC.
When preparations (1) - (2) are complete, press the [Enter] key on the PC.
( Or, click on the OK button.)
<Fig. 4-11-2>
--> The [AF Lens Data Input Complete] screen appears.
<Step 3>
AF Lens Data input is completed.

<Fig. 4-11-3>
93
4-12a. [F5] : CAMERA Adjustment

(shutter adjustment, adjustment for reduced aperture sensitivity, ISO sensitivity adjustment, white balance adjustment, AE
adjustment, offset level adjustment)
< Setup for Camera Adjustment> < Importance! >
1. Calibrate the pattern box before adjusting the camera.
2. Ensure that camera adjustment is carried out in dark surroundings (ideally in a darkroom
environment). If a darkroom cannot be set up, use a box painted black on the inside to cover the
camera before performing the adjustment.
Maximum 80mm
Maximum 45mm Maximum 30mm

Camera
Centerline Centerline
Pattern box
Filter (LB140)
<Note>
An error will occur during CAMERA adjustment, and adjustment cannot be completed, unless the pattern box is calibrated
correctly.
<Step 1>
Select [F5] CAMERA Adjustment on the [Adjustment Items Select] screen.
--> The [CAMERA Adjustment Preparation] screen appears.
CAMERA Adjustment
< CAMERA Adjustment Preparations >
(1) Prepare the LB140 filter.

(2) Adjust the color temperature of the pattern box (PTB450)
to 6100+-50K.
(3) Adjust the luminance of the pattern box (PTB450)
to 160+-5cd/m2.
(4) Set the camera in front of the pattern box.
(5) Match the zoom position to a wide edge.
(6) Darken surroundings.
When preparations (1)-(6) are complete,

press the [Enter] key on the PC.
<Fig. 4-12a-1>
<Step 2>
--> The [Shutter adjustment] screen appears.
94
<Step 3>
Shutter adjustment
(1) Set the distance between the camera and pattern box.
(2) The LB140 filter is not placed in front of the lens.

LB140 filter
------------------------------
| | |
| 45mm or less. | 30mm or less. |
| | |
<------ Center ------> | <------ Center ------> Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------
< Setup for CAMERA Adjustment >

<Fig. 4-12a-2>
--> The [Squeezing sensitivity decrease rate adjustment (with filter)] screen appears.
<Step 4>
Squeezing sensitivity decrease rate adjustment

(2) Place the LB140 filter in front of the lens.

LB140 filter
| ------------------------------
| | | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-3>
--> The [OFD sensibilty adjustment (without filter)] screen appears.
95
<Step 5>
OFD sensibilty adjustment

(2) Remove the LB140 filter from front of the lens.

LB140 filter
------------------------------
| <---------------------> <---------------------> | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-4>
--> The [WB adjustment (with filter)] screen appears.
<Step 6>
WB adjustment with filter


LB140 filter
| ------------------------------
| | | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-5>
--> The [WB adjustment (without filter)] screen appears.
96
<Step 7>
WB adjustment without filter


LB140 filter
------------------------------
| <---------------------> <---------------------> | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-6>
--> The [WB adjustment with filter (ISO800)] screen appears.
<Step 8>
WB adjustment with filter (ISO800)


LB140 filter
| ------------------------------
| | | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-7>
--> The [WB adjustment without filter (ISO800)] screen appears.
97
<Step 9>
WB adjustment without filter (ISO800)


LB140 filter
------------------------------
| <---------------------> <---------------------> | |
| | |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12a-8>
--> The [CAMERA Adjustment Complete] screen appears.
<Step 10>
Camera adjustment is completed.

Is Shading compensation adjustment continuously done?
Select N or Y of PC.
[ N ] To the adjustment selection screen
[ Y ] To the shading compensation adjustment
<Fig. 4-12a-9>
98
4-12b. [ S ]: Shading compensation adjustment
(Shading compensation adjustment)
< Setup for Shading compensation adjustment > < Importance! >
1. Calibrate the pattern box before adjusting the camera.
2. Ensure that camera adjustment is carried out in dark surroundings (ideally in a darkroom
environment). If a darkroom cannot be set up, use a box painted black on the inside to cover the
camera before performing the adjustment.
Maximum 80mm
Camera
Centerline
Pattern box
<Step 1>
Select [S] CAMERA Adjustment on the [Adjustment Items Select] screen.
--> The [Shading Compensation Adjustment Preparation] screen appears.
Shading compensation adjustment

(2) The LB140 filter is not placed in front of the lens.
Maximum 80mm ------------------------------

| <-----------------------------------------------------> | |
| |
| |
| <---------------------- Center ----------------------> Pattern box |
(PTB450) |
CAMERA |
| |
------------------------------

<Fig. 4-12b-1>
--> The [Zoom setting of [1] position] screen appears.
99
<Step 2>
Set the zoom position in 1
Zoom position = 1
Darken the surrounding, and press enter key of PC.
<Fig. 4-12b-2>
<Step 3>
Zoom position = 1
Out of alignment to the zoom position
<Fig. 4-12b-3>
100
<Step 4>
Zoom position = 12
<Fig. 4-12b-4>
<Step 5>
Zoom position = 21
<Fig. 4-12b-5>
101
<Step 6>
Zoom position = 27
<Fig. 4-12b-6>
<Step 7>
Zoom position = 31
<Fig. 4-12b-7>
102
<Step 8>
Zoom position = 1
<Fig. 4-12b-8>
--> The [Shading compensation adjustment Complete] screen appears.
<Step 8>
Shading compensation adjustment complete.

<Fig. 4-12b-9>
103
4-13. [F7] : Flash Adjustment

<Setup for Flash Adjustment>
(1) As flash adjustment is readily affected by external light, ensure that the vicinity of the gray chart is very dark.
(2) Ensure that distance is measured from the front of the camera during flash adjustment.
(3) When adjusting the flash, always ensure that AF adjustment is complete before beginning flash adjustment.
1000±10mm
Centerline
Camera
Gray chart
Setup for Flash Adjustment
<Step 1>
Select [F7] Flash Adjustment on the [Adjustment Items Select] screen.
--> The [Flash Adjustment Preparation] screen appears.
<Step 2>
Flash Adjustment
< Preparations >
(1) Prepare a gray chart (1000mm x 1000mm or more).

(2) Mount the camera on a tripod.
(3) Press the flash pop-up button
(4) Set the gray chart from the front side of the flash
on the place of 1000mm+/-10mm.
(5) Match the zoom position to a wide end.

<Fig. 4-13-1>
--> The [Flash Adjustment Start] screen appears.
104
<Step 3>
Flash Adjustment
(1) Adjust brightness so that the periphery of the gray chart
is as dark as possible.
(2) Adjust the camera so that the entire chart is
shown on the LCD monitor.
When preparations (1) and (2) are complete,

|<-------------------------------------------------------->
| 1000 +-10mm
//|
<---------------------Center--------------------->
CAMERA
< Setup for Flash Adjustment > Gray Chart (1000mm x 1000mmm)
<Fig. 4-13-2>
--> The [Flash Adjustment Complete] screen appears.
<Step 4>
Flash adjustment is completed.
Adjustment Item Selection Screen.

<Fig. 4-13-3>
105
4-14. [F1] : Battery Voltage Adjustment

<Setup for Battery Voltterge Adjustment>
(1) When adjusting the battery voltage, supply power (5.0V) to the camera from the [Power Cable Jig] before setting the jig
mode.
(2) Always measure input voltage in the vicinity of the DC IN terminal.
(3) When reducing the voltage, adjust the stabilized power supply to ensure that the voltage is not reduced excessively from
the measured point. The adjustment software may produce an error if communication between the adjustment software
and the camera is disrupted. Restart the adjustment software in this case.
USB
DC JACK
<Step 1>
Select [F1] Battery Voltage Adjustment on the [Adjustment Items Select] screen.
—> The [Battery Voltage Adjustment Preparation] screen appears.
106
<Step 2>
Battery Voltage Adjustment

<Preparations>
1. Check that the Power Cable Jig and the camera are connected.
*If not, return to the Jig Mode Setup screen,
and connect the Power Cable Jig and the camera.
2. Supply power (5.0V) to the camera from the
[Power Cable Jig].
When preparations are complete, press the [Enter] key on the PC.
<Fig. 4-14-1>
—> The [4.50V Input] screen appears.
<Step 3>

(1) Supply 4.50V (+0.02V/-0.00V).
<Fig. 4-14-2>
107
<Step 4>

(1) Supply 4.50V (+0.02V/-0.00V).
Result= **
(2) Supply 4.00V (+0.02V/-0.00V).
<Fig. 4-14-3>
<Step 5>

(1) Supply 4.50V (+0.02V/-0.00V).
Result= **
(2) Supply 4.00V (+0.02V/-0.00V).
Result= **
(3) Supply 7.20V (+0.02V/-0.00V).
<Fig. 4-14-4>
108
<Step 6>

(1) Supply 4.50V (+0.02V/-0.00V).
Result= **
(2) Supply 4.00V (+0.02V/-0.00V).
Result= **
(3) Supply 7.20V (+0.02V/-0.00V).
Result= **
(4) Supply 5.0V (+-0.1V).
<Fig. 4-14-5>
—> Write the adjustment data to the Flash ROM when adjustment has been completed correctly.
—> The [Battery Voltage Adjustment Complete] screen appears.
<Step 7>
The BATTERY adjustment is completed.

<Fig. 4-14-6>
109
4-15. [F2] : Mode Dial Adjustment

<Setup for Mode Dial Adjustment>
(1) When adjusting the Mode Dial, supply power (5.0V) to the camera from the [Power Cable Jig] before setting the jig mode.
(2) Always measure input voltage in the vicinity of the DC IN terminal.
(3) When reducing the voltage, adjust the stabilized power supply to ensure that the voltage is not reduced excessively from
the measured point. The adjustment software may produce an error if communication between the adjustment software
and the camera is disrupted. Restart the adjustment software in this case.
USB
DC JACK
<Step 1>
Select [F2] Mode Dial Adjustment on the [Adjustment Items Select] screen.
—> The [Mode Dial Adjustment Preparation] screen appears.
110
<Step 2>
Mode Dial Adjustment

(1) Set the mode dial to [AUTO].
(2) Please input 5.00+-0.01V from DC-IN Jack.
Press the [Enter] key of PC after setting the camera.
Press [1] key to PC when not proceeding to the next step.
<Fig. 4-15-1>
—> The [Mode Dial Adjustment Complete] screen appears.
<Step 3>
The Mode Dial adjustment is completed.

<Fig. 4-15-2>
111
4-16. [F11] : Video Adjustment

<Setup for Video Adjustment>
(1) Set up the PCI-2746C board in the computer as explained in the instructions for the video adjustment jig.
(2) If the waveform of the brightness signal (Y) or color signal (C) does not appear in the “WAVE No. 0” window during
adjustments, check the connections of the video adjustment jig.

AC100 ~ 240V
PCI-2746C PC for adjustment and checks

Video adjustments jig Board
USB cable
Video cable
AC Power
FinePix S9000/S9500 Adapter
<Step 1>
Select [F11] Video Adjustment on the [Adjustment Items Select] screen.
—> The [Video Adjustment Preparation] screen appears.
112
<Step 2>
VIDEO Adjustment
< VIDEO Adjustment Preparations >
(1) Connect the camera and video adj. jig with the video cable.
(2) Confirm Video jig is connected with the video cable.
When preparations are complete,

<Fig. 4-16-1>
—> The [VIDEO Adjustment Complete] screen appears.
<Step 3>
Video adjustment is completed.
1. Disconnect Video cable from camera.

2. Close the [WAVE No.0] window by close button.

<Fig. 4-16-2>
<Fig. 4-16-3>
113
4-17. [F8] : Firmware Download

Attention : When the download of the firmware is needed, FUJI SERVICE BULLETIN is contacted from
FTYO/QA. Till then, disregard this item.
<Setup for Firmware Download>
FinePix S9000/S9500
PC for adjustment and checks
USB cable
AC Power Adapter
<Step 1>
Select [F8] Firmware Download on the [Adjustment Items Select] screen.
Firmware Download
LED lights to orange while downloading the firmware.
Do not turn off the power while downloading the firmware.
c:\FxS9000_9500_W\Firmware\SU1740RS2_66.bin
Press the ENTER Key to start download.
<Fig. 4-17-1>
—> The [Firmware Download Start] screen appears.
114
<Step 2>
Firmware download
(1) Remove the Power cable jig from the camera.

(2) Turn off power switch.
(3) Reconnect Power cable jig.
(4) Turn on the power switch while pressing the shutter button.
(5) Press the [Enter] key after green LED lights on.
<Fig. 4-17-2>
—> The [Download Complete] screen appears if download is successful.
<Step 3>
Firmware download is completed
(1) Remove the DC Jack cable from the camera.

(2) Turn off power switch.
(3) Reconnect Power cable jig.
(4) Turn on the power switch while pressing the shutter button.
(5) Press the [Enter] key after green LED lights on.
The system returns to the Jig Mode Setup screen

when press the [Enter] key.
<Fig. 4-17-3>
115
4-18. [F12] : End Setting

(Destination setting, USB ID write, Product mode setting)
1. The End setting consist of the following settings.

* Destination setting
* USB ID write
* Product mode setting (mass storage identification)
2. The setting must always be run when the adjustment software is terminated. Failure to run Terminal Setting will prevent
identification as Mass Storage when the camera is connected to the PC.
3. USB ID write details
1) USB ID write requires that the USB device (in this case FinePix S9000_S9500) be unique throughout the world. For this
reason, each device has a unique ID as determined by the USB standard. If multiple devices with the same USB ID are
connected to a single PC, the PC will be unable to identify each USB device, thus preventing operation.
Item Details
Repair Date Date information is acquired from the PC and written.
Administrator ID 01(01)
Repair Station U.S.A. 61(a) SAPPORO 30(0)
CANADA 62(b) SENDAI 31(1)
HAWAII 63(c) TOKYO 33(3)
TAIWAN 64(d) NAGOYA 34(4)
ENGLAND 66(f) OSAKA 35(5)
GERMANY 67(g) HIROSHIMA 37(7)
FRANCE 68(h) FUKUOKA 38(8)
SPAIN 69(i)
ITALY 6A(j)
NETHERLANDS 6B(k)
BELGIUM 6C(l)
SWEDEN 6D(m)
SWITZERLAND 6E(n)
NORWAY 6F(o)
FINLAND 70(p)
SINGAPORE 71(q)
CHINA 74(t)
OTHER 7A(z)
Repair Serial No. A serial No. is assigned automatically and written
116
<Step 1>
Select [F12] End Setting on the [Adjustment Items Select] screen.
—> The [End Setting Description] screen appears.
<Step 2>
End Setting
The End settings consist of the destination setting,
the USB_ID write, and product mode settings
(= Mass Storage recognition).
Press the [Enter] key.
<Fig. 4-18-1>
—> The [Destination Setting] screen appears.
<Step 3>
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
The third character

<A> FinePix S9000 J-model 0 to 9
 FinePix S9000 US/CA-model A to H,J,K
<C> FinePix S9500 EU/EG/EE/AS-model L to N,P to V
<D> FinePix S9500 CH-model W to Z
<Fig. 4-18-2>
<Note>
This example assumes that US-Model has been selected. The following screen therefore appears.
—> The [US-Model selected] screen appears.
117
<Step 4>
Destination setting
The destination is selected from an undermentioned list,
according to third character from left side of the serial number.
The third character

<A> FinePix S9000 J-model 0 to 9
 FinePix S9000 US/CA-model A to H,J,K
<C> FinePix S9500 EU/EG/EE/AS-model L to N,P to V
<D> FinePix S9500 CH-model W to Z
Selected FinePix S9000 US/CA-model.

Press the [Enter] key!
<Fig. 4-18-3>
—> The [USB ID Writing] screen appears.
<Step 5>
Repair site ID input menu

The repair site is selected from an undermentioned list.
<A> SAPPORO SS <M> BRITAIN

 SENDAI SS <N> GERMANY
<C> TOKYO SS <O> FRANCE
<D> NAGOYA SS SPAIN
<E> OSAKA SS <Q> ITALY
<F> HIROSHIMA SS <R> NETHERLANDS
<G> FUKUOKA SS <S> BELGIUM
<H> U.S.A. <T> SWEDEN
 CANADA SWITZERLAND
<J> HAWAII <V> NORWAY
<K> TAIWAN <W> FINLAND
<X> SINGAPORE
<L> CHINA <Z> OTHERS
<Fig. 4-18-4>
<Note>
This example assumes that <H>U.S.A. has been selected. The following screen therefore appears.
—> The [USB_ID U.S.A.] screen appears.
118
<Step 6>
USB ID
Selected U.S.A..
Press the [Enter] key!
<Fig. 4-18-5>
—> The [FinePix S9000_9500 Adjustment End] screen appears.
<Step 7>
FinePix S9000_9500 Adjustment is completed.
1) Remove USB cable from the camera.
2) Press the [Enter] key.
--> The adjustment software returns to the Jig mode setup screen
after press the [Enter] key.
<Fig. 4-18-6>
119
5. Inspection FinePix S9000/S9500 Service Manual
5. Inspection
5-1. Required Measuring Equipment
Measuring equipment Remarks
Power supply AC adapter (AC-5V), Regurated power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
POWER CABLE JIG Common with adjustment JIG (ZJ00580-100)
xD-Picture card For general use
Macro Chart Resolution confirmation (ZJ00525-100)
TV Monitor TV monitor, minimum resolution 600 lines
LCD INSPECTION DATA Download and use ZJ00885-100
5-2. Connection of Measuring Equipment

Use POWER CABLE JIG
The output current of the Regurated power supply must not become 2.5A or more.
120
FinePix S9000/S9500 Service Manual 5. Inspection
5-3. Inspection and Factory Settings
Sequemnce Item Mode Preparations for adjustment Method of adjustment Measuring Measurement points
(measurement points, subject, other) (VRs, waveforms, required values) equipment and jigs (VRs, positions)
1 External visual Camera observation (1) Check for damage to the
check outer casing
(2) Check for problems with
the clicking or sliding
movement of switches
(3) Check for dust or fogging
in the viewfinder
(4) Check for dust or fogging
in the LCD
2 Power switch Auto mode (1) Load batteries into the
check LCD-ON camera.
(2) Insert a card and close (2) Card for recording
the card cover. checking
(3) Select the Mode dial (3) Mode: AUTO
setting.
(4) Turn the camera on in (4) Check that the camera
Photography mode. beeps.
(5) If a message prompting (5) <DISP/BACK>
the user to set the date
appears, press the button
specified on the right.
(6) Check the display status (6) Check that the live image
and text is displayed.
EVF-ON (7) Press the <EVF/LCD> (7) Check that the live image
button. is displayed.
(8) Turn the dioptric (8) Check that the blurring of
adjustment dial up and the EVF screen varies.
down. Check that the dial turns
smoothly between the
upper and lower limits.
(9) Check for blemishes in (9) Monitor a very bright
the CCD live image. subject and check that
the live image does not
dim or darken.
3 Shock noise check Auto mode (1) Apply a shock to the (1) Check for problems on
in Auto mode LCD-ON camera using the shock the LCD monitor.
jig. Check that the camera
recovers from
synchronicity disruption
(Note) Do not apply
shocks directly to the lens
or card cover.
121
4 Resolution check Auto mode (1) Use a macro resolution
Focusing check LCD-ON chart as the subject.
(2) Set the camera to Macro (2) Press the Macro button
mode. once.
Check that the Macro
icon (tulip) appears on
the LCD monitor.
(3) Press the flash pop-up (3) Check that the flash icon
button to pop up the (A) appears on the LCD
flash. monitor.
After checking, lower the
flash unit by 1 cm and
check that “A” appears
when the flash is carefully
released.
(4) Set the camera to flash (4) Use the “Flash button +
mode with red-eye Command dial”
reduction. combination to select
Red-eye reduction mode.
Check that the red-eye
reduction icon appears on
the LCD monitor.
(5) Close the pop-up flash. (5) Check that the pop-up
flash closes.
(6) Set the camera up so that (6) Set the zoom to the
the chart fills the screen extreme WIDE setting.
from corner to corner.
(7) Press the shutter button (7) Check that the viewfinder
to take a picture. LED changes from green
to orange (during
recording) and then to
green.
5 Manual focusing Auto mode (1) Set the MF/S-AF/C-AF (1) Check that the MF icon
check LCD-ON selector switch to MF. remains as displayed.
(2) Press the one-push AF (2) Check that the camera
button. focuses and that the
circle in the center of the
screen changes to yellow.
(3) Turn the focusing ring. (3) Check that appears
below the circle in the
center of the screen and
that the focus moves.
(4) Set the MF/S-AF/C-AF (4) Check that the MF icon
selector switch to AF. disappears.
6 Command dial P mode (1) Turn the command dial (1) Check that the F**
check LCD-ON left and right. number in the bottom left
of the monitor screen
changes.
122
7 Movie/audio Movie (1) Set the Mode dial to (1) Check that “STANDBY”
recording check mode Movie shooting mode. appears on the LCD
monitor.
LCD_ON (2) Press (S1 -> S2) and (2) Check that movie/audio
then release (S2 -> S1). recording begins.
Check that “REC”
appears on the LCD
monitor.
(3) Hold down S1 for 5 (3) Check that movie/audio
seconds and then recording ends and that
release. the data is recorded on
the card.
8 Movie/audio Playback (1) Set the camera to
playback check Playback mode.
(2) Press the 4-way button (2) Check that the movie is
(down) to play back the played back on the LCD
movie. monitor.
Check that the sound is
played back through the
speaker.
9 Playback check Playback (1) Check images shot at (1) Where the horizontal is TV monitor
macro resolutions as follows:350 TV lines or
(manual photography) better at the center and
300 TV lines or better at
the periphery (NTSC).
300 TV lines or better at
the center and 250 TV
lines or better at the
periphery (PAL).
(2) Turn the camera off.
10 Playback mode Playback (1) Insert a card.
check (2) Set the Mode dial to
Playback mode.
(3) If a message prompting (3) <DISP/BACK>
the user to set the date
appears, press the button
specified on the right.
(4) Check the playback (4) Check that the last image
image. shot appears, regardless
of whether it is automatic
or manual.
Check that the date is
displayed in the
YYYY.MM.DD format.
11 Erase mode check Erase (1) Select “Erase” -> “Erase (1) Check an erase message
all” from the menu and such as the following
then press the “OK” appears:
button. Japan: “ OK?”
Overseas: “ERASE ALL
OK?”
China: “ OK?”
(2) Press the “OK” button (2) Check that the recorded
again. images are erased.
123
12 LCD dust/defect Playback (1) Insert a standard xD- ZJ00885-100
check Picture card.
(2) Play back a completely (2) Check that there are no
black image. noticeable dust flecks or
stains (bright spots) on
the screen.
(3) Play back a completely (3) Check that there are no
white (75%) image. noticeable dust flecks or
stains (smears, flashing
points, etc.) on the
screen.
(4) Change the setting with (4) Play the above 2 frames
the EVF/LCD button. and perform the same
checks.
13 Battery low/ Auto mode (1) Connect the power
Backup check LCD-ON supply jig to the DC_IN
terminal.
(xD card loaded, no
Microdrive)
(2) Set the power supply (2) 5.00 ± 0.1 V
voltage.
(3) Set the Mode dial to (3) Check that the camera
AUTO and turn the starts up normally.
camera on in Camera
mode with the LCD on.
(4) Check that the pop-up (4) Press the flash pop-up
flash opens and closes button to pop up the flash
and check the backup. unit.
Check that the flash red-
eye reduction icon
appears. After completing
the check, use the “Flash
button + Command dial”
combination to return the
camera to Flash AUTO
mode.
(5) Set the pre-end voltage. (5) 4.50 ± 0.03 V Check that
the battery low warning
appears.
(6) Set the end voltage. (6) 4.00 ± 0.03 V Check that
the camera turns off.
124
14 Current Auto mode (1) Connect the power
consumption LCD-ON supply jig to the DC_IN
check terminal.
(xD-Picture card loaded,
no Microdrive)
(2) Set the power supply (2) 5.00 ± 0.05 V
voltage.
(3) Set the Mode dial to
AUTO and turn the
camera on.
(4) Press the EVF/LCD
selector switch.
(5) After the LCD live image (5) 650 mA or less.

appears, check the If the current
current consumption. consumption exceeds the
above value, it is OK if
the current drops into the
standard range within 10
seconds. If the current is
still outside the standard
range after 10 seconds,
the camera is faulty.
15 Shipping (1) Mode dial (1) AUTO
inspection (2) Flash (2) Pop down
(3) Battery and cards not
inserted
(4) Card cover (4) Closed
(5) Battery cover (5) Closed
(6) Power switch (6) OFF
(7) MF/S-AF/C-AF selector (7) S-AF
switch
(8) EVF dioptric adjustment (8) Center position indicator
dial located close to the
center.
(9) Zoom position (9) Set to extreme W
(10) Jack cover (10) Closed
(11) Metering mode switch (11) Multi-pattern metering
(12) Sync cap (12) Fitted
(13) SETUP frame No. (13) New The default SETUP
frame No. setting is
“Continuous”, but to clear
the number of frames in
the frame number
memory to zero, you
should always change the
setting to “New” before
turning the camera off.
125
5-4. Resolution Checking

<Step 1> Fluorescent light stand
Refer to the settings for resolution checking in the figure at
right and set up the camera and the high-resolution chart.
Use a light source to illuminate the high-resolution chart so High-resolution chart
that the surface brightness of the chart is 9.0 to 11.5 EV.
<Step 2>
Prepare the following:
For test photography
(1) Insert a formatted 32 MB xD picture card into the
WIDE: 375 mm TELE: 3950 mm
camera.
(2) Supply power to the camera. (Batteries can be used.)
(3) Set the camera to “A” mode and switch it on.
(4) Set the camera on a tripod and point it directly at the <Fig. 5-4-1> Setting for Inspecting Resolution
high-resolution chart (set at 90o horizontally and
vertically
(2)
relative to the chart). (1) (3)
(5) Position the high-resolution chart 375 mm from the end
of the lens at the WIDE setting and 3950 mm from the
end of the lens in the TELE setting.
<Step 3>
Make the following changes to the default photography mode
settings:
(1) Select A mode.
(2) Select “Fine” and “9M” (3488 x 2616) mode.
(3) Set the flash to OFF.
(4) Set the aperture for WIDE: F2.8, TELE: F4.9.
(5) Select ISO 200.
(6) Set the focusing mode to “S”.
(7) Adjust so that the angle of view is the same as the <Fig. 5-4-2> Resolution Check Image
chart displayed on the LCD monitor (Fig. 5-4-2).
(1) (2)
<Step 4>
To avoid camera shake, set the self-timer to 2 seconds and
then press the camera's shutter button.
--> A resolution checking image (Fig. 5-4-2) is recorded.
<Step 5>
Download the resolution checking image to your computer.
<Step 6>
Resolution checking image enlargement procedure (Fig. 5-4-
2 (2)).
(1) Open the image in Photoshop 5.0.
(2) Display the image as shown in Fig. 5-4-3.
The procedure varies depending on your software
settings.
(3) Use the zooming tool in the tool box (Fig. 5-4-3 (1)) to <Fig. 5-4-3> Enlargement Using Photoshop
enlarge the area shown in Fig. 5-4-3 (2) to 300%.
(4) When you enlarge the image, the centrally enlarged
image (Fig. 5-4-4) appears.
126
The centrally enlarged image (Fig. 5-4-4 (1)) is normal if a
resolution of 1400 lines can be confirmed. (1)
Use the same procedure to check the resolution of
peripherally enlarged versions (Fig. 5-4-5 (1)) of the
resolution checking image (Fig. 5-4-2 (3)). The peripherally
enlarged image is normal if a resolution of 1000 lines can be
confirmed.
Check location Service resolution value

Center (horizontal/vertical) 1400 <Fig. 5-4-4> Enlargement to 300% (Center)
Peripheral (horizontal/vertical) 1000
[Note!]
The resolution values given in this description are not the (1)
original “FinePix S9000/S9500” resolution values (TV
resolution). The values given are according to the high-
resolution chart set in the jig.
Accordingly, the values shown in the above table are for
servicing purposes and should be confirmed as being for use
in in-house inspections.
<Fig. 5-4-5> Enlargement to 300% (Peripheral)
127
6. Parts List FinePix S9000/S9500 Service Manual
6. Parts List
6-1. Packing and Accessories
6-1-1. US-model (FinePix S9000)
A107
A106
A112
A113
A115 A111
A123
A114
A122 A108 A118 A105
A109
A121
A120
A119
A110
A116
A102
A103
A101
A104
A117
Ref No. Parts No. Description Comment EL Ref No. Parts No. Description Comment EL
A101 FZ06183-200 UNITARY BOX N A116 FZ06269-100 CD-ROM N

A102 FZ06406-100 UNITARY BOX PAD N A117 BB18772-100 DEST.LBL.17400US JFG N
A103 FZ06187-100 SHEET MOLD N A118 BB18002-100 CERTIFICATION SEAL N
A104 BB12943-100 BAR CODE LABEL BLANK N A119 BL00472-200 MANUAL E N
A105 AZF0000-321 HDPE BAG NO.12 N A120 BL00473-200 QUICK GUIDE E N
A106 FZ06229-100 AV CABLE N A121 BL00473-500 QUICK GUIDE S N

A107 FZ06230-100 USB CABLE W N A122 BL00372-100 IMPORTANT SAFETY N
A108 BB13161-200 SHOULDER BELT N A123 BL00373-100 US WARRANTY N
A109 FZ06312-100 HOOD N
A110 FZ04793-100 ALKALINE BATTERY =
A111 AZF0000-101 LDPE BAG NO.10 N

A112 FZ06311-101 LENS CAP N
A113 BB12402-100 LENSCAP HOLDER N
A114 BF04146-100 XDCARD 16MB ASSY =
A115 BL00209-100 CASE N
128
FinePix S9000/S9500 Service Manual 6. Parts List
6-1-2. CA-model (FinePix S9000)
A107
A106
A112
A113
A115 A111
A122
A114
A108 A118 A105
A109
A121
A120
A110
A119
A116
A102
A103
A101
A104
A117

A102 FZ06406-100 UNITARY BOX PAD N A117 BB18772-400 DEST.LBL.17400CA JFG N
A105 AZF0000-321 HDPE BAG NO.12 N A120 BL00472-300 MANUAL F N
A106 FZ06229-100 AV CABLE N A121 BL00473-200 QUICK GUIDE E N

A107 FZ06230-100 USB CABLE W N A122 BL00473-300 QUICK GUIDE F N
A108 BB13161-200 SHOULDER BELT N
A109 FZ06312-100 HOOD N

A115 BL00209-100 CASE N
129
6-1-3. EU-model (FinePix S9500)
A107
A106
A112
A113
A115 A111
A125
A114
A124 A108 A118 A105
A109
A123
A122
A121
A110
A120
A119
A116
A102
A103
A101
A104
A117

A102 FZ06406-100 UNITARY BOX PAD N A117 BB18772-200 DEST.LBL.17400EU JFG N
A105 AZF0000-321 HDPE BAG NO.12 N A120 BL00472-300 MANUAL F N
A106 FZ06229-100 AV CABLE N A121 BL00472-400 MANUAL G N

A107 FZ06230-100 USB CABLE W N A122 BL00473-200 QUICK GUIDE E N
A108 BB13161-200 SHOULDER BELT N A123 BL00473-300 QUICK GUIDE F N
A109 FZ06312-100 HOOD N A124 BL00473-400 QUICK GUIDE G N
A110 FZ04793-100 ALKALINE BATTERY = A125 BL00473-500 QUICK GUIDE S N

A115 BL00209-100 CASE N
130
6-1-4. EG-model (FinePix S9500)
A107
A106
A112
A113
A115 A111
A121
A114
A108 A118 A105
A109
A120
A119
A110
A116
A102
A103
A101
A104
A117

A102 FZ06406-100 UNITARY BOX PAD N A117 BB18772-300 DEST.LBL.17400EG JFG N
A105 AZF0000-321 HDPE BAG NO.12 N A120 BL00473-200 QUICK GUIDE E N
A106 FZ06229-100 AV CABLE N A121 BL00176-102 H14 WARRANTY CARD EG N

A107 FZ06230-100 USB CABLE W N
A108 BB13161-200 SHOULDER BELT N
A109 FZ06312-100 HOOD N

A115 BL00209-100 CASE N
131
6-1-5. EE-model (FinePix S9500)
A107
A106
A112
A113
A115 A111
A114
A108 A118 A105
A109
A120
A110
A119
A116
A102
A103
A101
A104
A117
A101 FZ06184-100 UNITARY BOX N A111 AZF0000-101 LDPE BAG NO.10 N

A102 FZ06406-100 UNITARY BOX PAD N A112 FZ06311-101 LENS CAP N
A103 FZ06187-100 SHEET MOLD N A113 BB12402-100 LENSCAP HOLDER N
A104 BB12943-100 BAR CODE LABEL BLANK N A114 BF04146-100 XDCARD 16MB ASSY =
A105 AZF0000-321 HDPE BAG NO.12 N A115 BL00209-100 CASE N
A106 FZ06229-100 AV CABLE N A116 FZ06269-100 CD-ROM N

A107 FZ06230-100 USB CABLE W N A117 BB18772-700 DEST.LBL.17400EE JFG N
A108 BB13161-200 SHOULDER BELT N A118 BB18002-100 CERTIFICATION SEAL N
A109 FZ06312-100 HOOD N A119 BL00472-200 MANUAL E N
A110 FZ04793-100 ALKALINE BATTERY = A120 BL00473-200 QUICK GUIDE E N
132
6-1-6. AS-model (FinePix S9500)
A107
A106
A112
A113
A115 A111
A114
A108 A118 A105
A109
A120
A110
A119
A116
A102
A103
A101
A104
A117
A101 FZ06184-100 UNITARY BOX N A111 AZF0000-101 LDPE BAG NO.10 N

A102 FZ06406-100 UNITARY BOX PAD N A112 FZ06311-101 LENS CAP N
A103 FZ06187-100 SHEET MOLD N A113 BB12402-100 LENSCAP HOLDER N
A104 BB12943-100 BAR CODE LABEL BLANK N A114 BF04146-100 XDCARD 16MB ASSY =
A105 AZF0000-321 HDPE BAG NO.12 N A115 BL00209-100 CASE N
A106 FZ06229-100 AV CABLE N A116 FZ06269-100 CD-ROM N

A107 FZ06230-100 USB CABLE W N A117 BB18772-600 DEST.LBL.17400AS JFG N
A108 BB13161-200 SHOULDER BELT N A118 BB18002-100 CERTIFICATION SEAL N
A109 FZ06312-100 HOOD N A119 BL00472-200 MANUAL E N
A110 FZ04793-100 ALKALINE BATTERY = A120 BL00473-200 QUICK GUIDE E N
133
6-1-7. CH-model (FinePix S9500) Revised: 11. Nov. 2005
A107
A106
A112
A113
A115 A111
A114
A108 A109 A105
A117
A110
A119
A116
A102
A103
A101
A104
A118
Ref No. Parts No. Description Comment Ref No. Parts No. Description Comment
A101 FZ06183-300 UNITARY BOX A111 AZF0000-101 LDPE BAG NO.10

A102 FZ06406-100 UNITARY BOX PAD A112 FZ06311-101 LENS CAP
A103 FZ06187-100 SHEET MOLD A113 BB12402-100 LENSCAP HOLDER
A104 BB12943-100 BAR CODE LABEL BLANK A114 FHM0516-100 XDCARD 16MB ASSY
A105 AZF0000-321 HDPE BAG NO.12 A115 BL00209-100 CASE
A106 FZ06229-100 AV CABLE A116 FZ06269-100 CD-ROM

A107 FZ06230-100 USB CABLE W A117 BB19102-100 WARRANTY CN
A108 BB13161-200 SHOULDER BELT A118 BB19104-100 REGULATION SEAL
A109 FZ06312-100 HOOD A119 BL00472-600 MANUAL C
A110 FZ04793-100 ALKALINE BATTERY
134
6-1-8. JP-model (FinePix S9000) Revised: 11. Nov. 2005
A107
A106
A112
A113
A111
A108 A109 A105

A116
A110
A115
A114
A102
A103
A117
A101
A104
A101 FZ06183-100 UNITARY BOX A111 AZF0000-101 LDPE BAG NO.10

A102 FZ06406-100 UNITARY BOX PAD A112 FZ06311-101 LENS CAP
A103 FZ06187-100 SHEET MOLD A113 BB12402-100 LENSCAP HOLDER
A104 BB12943-100 BAR CODE LABEL BLANK A114 FZ06269-100 CD-ROM
A105 AZF0000-321 HDPE BAG NO.12 A115 BL00472-100 MANUAL J
A106 FZ06229-100 AV CABLE A116 BL00190-100 SAFETYCARD H14

A107 FZ06231-100 USB CABLE J A117 BB18949-100 WARRANTY CARD
A108 BB13161-200 SHOULDER BELT
A109 FZ06312-100 HOOD
A110 FZ01782-100 ALKALINE BATTRY
135
6-2. Cabi Front Block

6-2-1. US-model (FinePix S9000)
M207 M222
M215 M221
M219
M227
D
M215
M220 M207
A M234
M228 E M217 M207
M207 M215
B M233
M226
M211 M223
C M213 M229
M210
M215 K TAPE
M229 M202 M207
M225
M208 M214
N.S
M203 F
M212
M205 M207
M201 M204
M218
M206
M229
M216 K TAPE
M209
M231
G
M230
M232
M229
M224
N.S=Not Supply
M201 BU03062-100 ASSY CASE F + M221 FZ06466-100 SHEET GRAPHITE =

M202 BB17785-100 WINDOW AF N M222 BB17793-100 FRAME BATT N
M203 BB17786-100 WINDOW SUB LIGHT N M223 BB17794-100 FRAME PWB N
M204 BB17787-100 RING SUB LIGHT N M224 BB17891-100 SHEET EMI-CCD N
M205 BB17795-100 TAPE SUB LIGHT N M225 BB17797-100 BASE TRIPOD N
M206 BB18675-100 CCD BADGE N M226 BB17892-100 SHEET EMI-FLAME N

M207 BB17335-400 BT2M1.7X4.0B N M227 FZ06282-100 AF SENSOR UNIT N
M208 BB17790-100 STRAP LEFT N M228 BU03216-100 AF ILLUMI ASSY N
M209 BB17788-100 COVER JACK N M229 BB19086-300 N-MS2M1.7X3.5BN N
M210 FZ06350-100 SYNCHRO TERMINAL N M230 BB17813-100 BUTTON FLASH N
M211 FZ06351-100 WIRE HARNESS N M231 BB17814-100 CSP FL BUTTON N

M212 BB17818-100 COVER SYNCHRO N M232 BB17870-200 LABEL PRODUCT N
M213 BB17791-100 HOLDER LENS + M233 BB17886-100 SHEET EMI-SIDE N
M214 BB17837-100 CUSHION N M234 BB17885-100 SHEET EMI-BASE N
M215 BB17681-600 BT2M1.7X5.0 N
M216 BF05747-100 LENS ASSY =

M217 BB19087-G00 MS0M2.0X8.0BN
M218 FZ06302-100 SW UNIT N
M219 FZ06347-100 MIC ASSY N
M220 FZ05848-100 UNIT BATT HOLDER N Revised: 27. Dec. 2005
136
6-2-2. CA-model (FinePix S9000)
M207 M222
M215 M221
M219
M227
D
M215
M220 M207
A M234
M228 E M217 M207
M207 M215
B M233
M226
M211 M223
C M213 M229
M210
M215 K TAPE
M229 M202 M207
M225
M208 M214
N.S
M203 F
M212
M205 M207
M201 M204
M218
M206
M229
M216 K TAPE
M209
M231
G
M230
M232
M229
M224
N.S=Not Supply



M215 BB17681-600 BT2M1.7X5.0 N
M216 BF05747-100 LENS ASSY =

M217 BB19087-G00 MS0M2.0X8.0BN
M218 FZ06302-100 SW UNIT N
137
6-2-3. JP-model (FinePix S9000)
M207 M222
M215 M221
M219
M227
D
M215
M220 M207
A M234
M228 E M217 M207
M207 M215
B M233
M226
M211 M223
C M213 M229
M210
M215 K TAPE
M229 M202 M207
M225
M208 M214
N.S
M203 F
M212
M205 M207
M201 M204
M218
M206
M229
M216 K TAPE
M209
M231
G
M230
M232
M229
M224
N.S=Not Supply



M215 BB17681-600 BT2M1.7X5.0 N
M216 BF05747-100 LENS ASSY =

M217 BB19087-G00 MS0M2.0X8.0BN
M218 FZ06302-100 SW UNIT N
138
6-2-4. EU/EG/EE-model (FinePix S9500)
M207 M222
M215 M221
M219
M227
D
M215
M220 M207
A M234
M228 E M217 M207
M207 M215
B M233
M226
M211 M223
C M213 M229
M210
M215 K TAPE
M229 M202 M207
M225
M208 M214
N.S
M203 F
M212
M205 M207
M201 M204
M218
M206
M229
M216 K TAPE
M209
M231
G
M230
M232
M229
M224
N.S=Not Supply



M215 BB17681-600 BT2M1.7X5.0 N
M216 BF05747-100 LENS ASSY =

M217 BB19087-G00 MS0M2.0X8.0BN
M218 FZ06302-100 SW UNIT N
M219
M220
FZ06347-100
FZ05848-100
MIC ASSY
UNIT BATT HOLDER
N
N
139
6-2-5. AS/CH-model (FinePix S9500)
M207 M222
M215 M221
M219
M227
D
M215
M220 M207
A M234
M228 E M217 M207
M207 M215
B M233
M226
M211 M223
C M213 M229
M210
M215 K TAPE
M229 M202 M207
M225
M208 M214
N.S
M203 F
M212
M205 M207
M201 M204
M218
M206
M229
M216 K TAPE
M209
M231
G
M230
M232
M229
M224
N.S=Not Supply
M201 BU03062-100 ASSY CASE F M221 FZ06466-100 SHEET GRAPHITE

M202 BB17785-100 WINDOW AF M222 BB17793-100 FRAME BATT
M203 BB17786-100 WINDOW SUB LIGHT M223 BB17794-100 FRAME PWB
M204 BB17787-100 RING SUB LIGHT M224 BB17891-100 SHEET EMI-CCD
M205 BB17795-100 TAPE SUB LIGHT M225 BB17797-100 BASE TRIPOD
M206 BB18675-100 CCD BADGE M226 BB17892-100 SHEET EMI-FLAME

M207 BB17335-400 BT2M1.7X4.0B M227 FZ06282-100 AF SENSOR UNIT
M208 BB17790-100 STRAP LEFT M228 BU03216-100 AF ILLUMI ASSY
M209 BB17788-100 COVER JACK M229 BB19086-300 N-MS2M1.7X3.5BN
M210 FZ06350-100 SYNCHRO TERMINAL M230 BB17813-100 BUTTON FLASH
M211 FZ06351-100 WIRE HARNESS M231 BB17814-100 CSP FL BUTTON

M212 BB17818-100 COVER SYNCHRO M232 BB17870-400 LABEL PRODUCT
M213 BB17791-100 HOLDER LENS M233 BB17886-100 SHEET EMI-SIDE
M214 BB17837-100 CUSHION M234 BB17885-100 SHEET EMI-BASE
M215 BB17681-600 BT2M1.7X5.0
M216 BF05747-100 LENS ASSY

M217 BB19087-G00 MS0M2.0X8.0BN
M218 FZ06302-100 SW UNIT
M219 FZ06347-100 MIC ASSY
M220 FZ05848-100 UNIT BATT HOLDER Revised: 27. Dec. 2005
140
6-3. Internal Block
6-3-1. US/CA/JP-model (FinePix S9000)
M309 M311
M301
M308 M308
M310
M326
J M303
M307
M323
M323 K
M315 L
M325 M304
M308 I
I M308 A DO M324 M304
K
N.S H M313 P
M312
M308 EN F
M320 B J M304
M319 M304
C L
M318 M317
M305
GM
M302 K TAPE
M316 M314
M322
M304
M321
M306
N.S=Not Supply
M301 BU03238-100 EVF UNIT CONST N M316 BF05749-100 TOP FPC CONST
M302 CB1678-A101 MAIN PWB ASSY + M317 BB17792-100 PLATE FPC TOP D N
M303 FZ06283-100 EJECTOR N M318 BB17868-100 PLATE FPC TOP N
M304 BB17349-100 MSWM1.7X2.5 N M319 BB17878-100 TAPE FPC TOP D N
M305 CB1679-A100 DCST PWB ASSY N M320 BB17877-100 TAPE FPC TOP N
M306 BB17796-100 TUBE CONDENSER N M321 BB17887-100 SHEET EMI-TOP N

M307 BB17866-100 SHEET CF N M322 BB17335-200 BT2M1.7X3.0B N
M308 BB17335-400 BT2M1.7X4.0B N M323 BB19183-600 N-BT2M1.7X5.0B N
M309 BF05116-100 FLASH CONST = M324 BB19189-100 PLATE GND N
M310 FZ06247-100 LIGHT N M325 BB17798-100 WINDOW FLASH N
M311 BB17812-100 FLASH TOP N M326 CB1684-A100 TRG PWB ASSY N

M312 CB1684-A200 STSW PWB ASSY N
M313 FZ06344-100 WIRE HARNESS N
M314 FZ06345-100 FFC N
M315 BU03065-100 ASSY CASE TOP +

141
6-3-2. EU/EG/EE/AS/CH-model (FinePix S9500)
M309 M311
M301
M308 M308
M310
M326
J M303
M307
M323
M323 K
M315 L
M325 M304
M308 I
I M308 A DO M324 M304
K
N.S H M313 P
M312
M308 EN F
M320 B J M304
M319 M304
C L
M318 M317
M305
GM
M302 K TAPE
M316 M314
M322
M304
M321
M306
N.S=Not Supply
M301 BU03238-100 EVF UNIT CONST N M316 BF05749-100 TOP FPC CONST
M302 CB1678-A101 MAIN PWB ASSY + M317 BB17792-100 PLATE FPC TOP D N
M303 FZ06283-100 EJECTOR N M318 BB17868-100 PLATE FPC TOP N
M304 BB17349-100 MSWM1.7X2.5 N M319 BB17878-100 TAPE FPC TOP D N
M305 CB1679-A100 DCST PWB ASSY N M320 BB17877-100 TAPE FPC TOP N
M306 BB17796-100 TUBE CONDENSER N M321 BB17887-100 SHEET EMI-TOP N

M307 BB17866-100 SHEET CF N M322 BB17335-200 BT2M1.7X3.0B N
M308 BB17335-400 BT2M1.7X4.0B N M323 BB19183-600 N-BT2M1.7X5.0B N
M309 BF05116-200 FLASH CONST = M324 BB19189-100 PLATE GND N
M310 FZ06247-100 LIGHT N M325 BB17798-100 WINDOW FLASH N
M311 BB17812-200 FLASH TOP N M326 CB1684-A100 TRG PWB ASSY N

M312 CB1684-A200 STSW PWB ASSY N
M313 FZ06344-100 WIRE HARNESS N
M314 FZ06345-100 FFC N
M315 BU03065-100 ASSY CASE TOP +
142
6-4. Cabi Rear Block
6-4-1. US/CA/JP-model (FinePix S9000)
M428 M427
M401 M415
M419 M420
M425 M422
M404
M409
M421
M408
M406 M407 M424
M413
M403
M418
M405
M414 H
M416
M423
M430
M415 M N.S
M432 M416 K TAPE
M402
M429 M431
M415 M425 M426
O
M415 M417 P
N M410 M415
M412 M411
N.S=Not Supply
M401 BU03064-100 ASSY CASE R + M421 BF05613-100 LCD CONST N

M402 FZ06346-100 SPEAKER ASSY N M422 BU03083-100 ASSY CASE LCD F N
M403 BB17816-100 COVER CARD N M423 BB17843-100 CASE LCD R N
M404 BB13167-200 CARD SHAFT N M424 FZ05850-100 UNIT HINGI N
M405 BB17826-100 BUTTON REAR N M425 BB19085-A00 MS2M1.7X2.0N N
M406 BB17827-100 GUIDE LIGHT N M426 CB1683-A100 ML FPC ASSY N

M407 BB17828-100 SHEET SW N M427 BB17844-100 COVER FPC N
M408 BB17829-100 SHOE N M428 BB17803-100 SHEET COVER FPC N
M409 BB17830-100 COVER SHOE N M429 BB19084-100 N-MSWM1.7X2.5N N
M410 N.S. SHOE CONST N M430 BB17881-100 CUSHION EMI-R N
M411 BB19078-H00 MS2M1.7X6.5N N M431 BB17888-100 SHEET EMI-R-RIGHT N

M412 BB17335-600 BT2M1.7X5.0B N M432 BB17889-100 SHEET EMI-R-LEFT N
M413 BB17834-100 FRAME FINDER N
M414 CB1680-A100 KEY PWB ASSY N
M415 BB17335-400 BT2M1.7X4.0B N
M416 BB19086-300 N-MS2M1.7X3.5BN N

M417 BB17784-100 PLATE REAR N
M418 BB19183-600 N-BT2M1.7X5.0B N
M419 BB17864-100 STRAP RIGHT N
M420 BB17838-100 WINDOW LCD N
143
6-4-2. EU/EG/EE/AS/CH-model (FinePix S9500)
M428 M427
M401 M415
M419 M420
M425 M422
M404
M409
M421
M408
M406 M407 M424
M413
M403
M418
M405
M414 H
M416
M423
M430
M415 M N.S
M432 M416 K TAPE
M402
M429 M431
M415 M425 M426
O
M415 M417 P
N M410 M415
M412 M411
N.S=Not Supply
M401 BU03064-100 ASSY CASE R + M421 BF05613-100 LCD CONST N

M402 FZ06346-100 SPEAKER ASSY N M422 BU03083-100 ASSY CASE LCD F N
M403 BB17816-100 COVER CARD N M423 BB17843-100 CASE LCD R N
M404 BB13167-200 CARD SHAFT N M424 FZ05850-100 UNIT HINGI N
M405 BB17826-100 BUTTON REAR N M425 BB19085-A00 MS2M1.7X2.0N N
M406 BB17827-100 GUIDE LIGHT N M426 CB1683-A100 ML FPC ASSY N

M407 BB17828-100 SHEET SW N M427 BB17844-100 COVER FPC N
M408 BB17829-100 SHOE N M428 BB17803-100 SHEET COVER FPC N
M409 BB17830-100 COVER SHOE N M429 BB19084-100 N-MSWM1.7X2.5N N
M410 N.S. SHOE CONST N M430 BB17881-100 CUSHION EMI-R N
M411 BB19078-H00 MS2M1.7X6.5N N M431 BB17888-100 SHEET EMI-R-RIGHT N

M412 BB17335-600 BT2M1.7X5.0B N M432 BB17889-100 SHEET EMI-R-LEFT N
M413 BB17834-100 FRAME FINDER N
M414 CB1680-A100 KEY PWB ASSY N
M415 BB17335-400 BT2M1.7X4.0B N
M416 BB19086-300 N-MS2M1.7X3.5BN N

M417 BB17784-100 PLATE REAR N
M418 BB19183-600 N-BT2M1.7X5.0B N
M419 BB17864-100 STRAP RIGHT N
M420 BB17838-100 WINDOW LCD N
144
6-5. Electrical parts
[NOTE]
The components indicated by mark are critical for safety. * Due to standardization, replacement in the parts list may be different from
When indicated parts by reference number, please include the parts list specified in the circuit or the components used on the set.
the board name.
MAIN PWB ASSY KEY PWB ASSY
[CONNECTOR] [SWITCH]
CN100 FGB170-0571 CONNECTOR CJ 57P FN 0.3MM NH N SW750 FZ06162-100 DETECTOR SWITCH N
CN200 FGA162-0022 CONNECTOR CJ 2P RN 0.8MM PH N SW751 FZ04926-100 TACT SWITCH N
CN201 FGB163-0241 CONNECTOR CJ 24P FN 0.5MM NH N SW752 FZ05894-100 DETECTOR SWITCH N
CN202 FGB162-0081 CONNECTOR CJ 8P FN 0.5MM NV N SW753 FZ04926-100 TACT SWITCH N
CN204 FGY097-0201 CONNECTOR CJ 20P B 1MM NN N SW755 FZ04926-100 TACT SWITCH N

CN205 FGY069-0503 CONNECTOR CJ 50P RB 0.63MM NN N SW756 FZ04926-100 TACT SWITCH N
CN206 FZ05744-100 JACK USB MINI-B N SW757 FZ04926-200 TACT SWITCH N

CN550 FGC190-0701 CONNECTOR CJ 70P BN 0.5MM PV N
[CONNECTOR]
[JACK] CN750 FGB161-0241 CONNECTOR CJ 24P FN 0.5MM NH N
J200 FZ04344-100 JACK N CN751 FGB165-0161 CONNECTOR CJ 16P FN 0.5MM NH N
[BATTERY]
BT300 FZ04705-200 BATTERY = TOP FPC CONST
[SWITCH]
DCST PWB ASSY SW850 FZ04993-101 TACT SWITCH N
SW851 FZ06162-100 DETECTOR SWITCH N
[FUSE] SW852 FZ06162-100 DETECTOR SWITCH N
F600 FP00039-253 FUSE 2.5A 32V UL N SW853 FZ04926-100 TACT SWITCH N
F601 FP00043-253 FUSE 2.5A 125V JIS N SW854 FZ04926-100 TACT SWITCH N
F602 FP00039-253 FUSE 2.5A 32V UL N
F605 FP00042-752 FUSE 0.75A 24V UL N SW855 FZ04926-100 TACT SWITCH N
[CONNECTOR]
CN600 FGA169-0021 CONNECTOR CJ 2P SN 1.5MM RV N
CN601 FGA162-0021 CONNECTOR CJ 2P RN 0.8MM PH N
CN603 FGC189-0701 CONNECTOR CJ 70P BN 0.5MM RV N

CN702 FGA174-0041 CONNECTOR LJ 4P SN 2.0MM PV N
[JACK]
J600 FZ05847-100 JACK N
145
7. Appendix FinePix S9000/S9500 Service Manual
7. Appendix
7-1. List of Related Technical Updates Issued
To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates issued
that cover this device.
Technical Update No. Date Title Details/Other
Service manual Revised pages: P70, P75, P86, P88, P92, P94,
2005-088 11, Nov. 2005
revision P99, P132 to P140
Parts list correction and Revised pages: P70, P112, P126 to P127,
2005-104 27, Dec. 2005
Service manual revision P136 to P141 and P145
Adjustment software and
2006-005 08, Feb. 2006 Revised pages: P82 and P88
Service manual revision
2006-012 24, Feb. 2006 Service manual revision Revised page: P92
146
FUJI PHOTO FILM CO., LTD.
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.

Fujifilm FinePix S9000 S9500 Service Manual PDF

Uploaded by

Copyright:

Available Formats

Fujifilm FinePix S9000 S9500 Service Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fujifilm FinePix S9000 S9500 Service Manual PDF

Uploaded by

Copyright:

Available Formats

DIGITAL CAMERA

that exposed parts are acceptably insulated from the

RoHS lead-free compliance

<Background & Overview>

*1: Excluded items (list of the main lead-related items)

 Differences in the soldering work for lead-free and eutectic solder

 Setting temperature during lead-free soldering

• Soldering iron tip temperature

• Correct bonding temperature

 Precautions when soldering with lead-free solder

• Uniform heating of the board and components

 Solder wire (thread)

Wire diameter 0.8mm

Solder type (Displayed symbol)

 Solder application wires (mesh, wicking wire, etc.)

7. Appendix ............................................................ 146

Standard number of available frames/recording time per media

Quality setting F N (30 fps) (30 fps)

Power Supply and Others

JPEG: Joint Photographic Experts Group

1-3. Names of External Components

Power switch Hot shoe AF-assist illuminator

Command dial Synchronizing terminal

AE-L (AE lock) button

Photo mode ( ) button

xD-Picture Card slot

Flash pop-up button Microphone

Zoom ring INFO (information check)

USB socket (mini-B)

A/V OUT (Audio / Visual output)

DC IN 5V (power input) socket

Focus mode selector switch Macro button

(One-touch AF) button

EVF UNIT CONST MAIN PWB SSSY

UNIT BATT HOLDER

BATTERY LID MIC ASSY

BASE TRI POD

(1) Remove the 2 screws (M1.7 x 5.0).

(2) Press BUTTON FLASH to open the flash.

COMMAND on the CONST CASE TOP and push it up 3

(5) Pushing the CONST CASE TOP up in the direction of 6

(7) Remove the TOP FPC in the direction of the arrow.

(1) Remove the 4 screws (M1.7 x 3.0). 1

2-4. Removing the CASE R CONST

(1) Remove the screw (M1.7 x 5.0).

(4) Remove the 6 screws (M1.7 x 3.5).

(8) Remove the SPEAKER ASSY connector.

(9) Remove the SHOE WIRE HARNESS connector.

(10) After removing the connectors, remove the LCD FPC

(2) Run the SHOE CONST, AF ILLUMI ASSY and FLASH

(7) Remove the BUTTON REAR in the direction of the

(1) Remove the 2 screws (M1.7 x 4.0). 1

(3) Run the LCD FPC to the inside.

(5) Squeeze the catches on the CASE LCD F in the

CAMERA SIDE LCD SIDE

(1) Remove the WIRE HARNESS.

If you are removing the WIRE HARNESS for the

(10) Remove the 6 screws (M1.7 x 2.5). 10

(15) Remove the BATT HOLDER connector.

Differences in the soldering work for lead-free and eutectic solder

Setting temperature during lead-free soldering

Precautions when soldering with lead-free solder

Solder wire (thread)

Solder application wires (mesh, wicking wire, etc.)

Revised: 27. Dec. 2005