User Manual: CLT1 - Hand Held A/C Test - Module For Externally Controlled A/C Compressors

User Manual
CLT1 – Hand Held A/C Test - Module for externally controlled

A/C Compressors
Dear Customer,
Thank you for making the decision to purchase the CLT-1 from COMPRESSORTECH.
The CLT-1 can be used for testing all Clutch Less Direct Drive Externally Controlled compressors
simply all year round, no matter how Low or High the ambient Temperature. The CLT-1 allows you to
expand your A/C Diagnostic Skills and has been designed by “Technicians For Technicians”.
Technical Application;
The CLT1 will provide a direct power supply to the Electronic control valve on all Clutch Less Direct
Drive externally controlled A/C Compressors without having to integrate the vehicles electrics.
Its simple, easy to use format, will greatly save valuable A/C Diagnostic time.
CLT-1 Kit Options:
Pt No: CLT1
• CLT1 Test- Unit with User Manual
• Cable with clamps for 12v Battery Power Supply
• Universal Cable to connect the Control valve
• Shipped in a rugged plastic box
Pt No: CLT-SET-1
• Hook with a strong magnet
• Cable with connector for VAG - Group
• Cable with connector for Compressor from Denso
• Simulator for connecting on the car
• Digital Measuring unit for measuring signals from the car.
Pt No: CLT-SET-2
• Hook with a strong magnet
• Cable with an connector for VAG - Group
• Cable with an connector for Compressor from Denso
• Simulator for connecting on the car
PAGE 1 OF 9
CLT-1 Overview;
1. Button to increase the compressor voltage

2. Button to decrease the compressor voltage
3. LED indicating short-circuit or interruption at the electromagnetic valve
4. LED indicating excess high power input of the electromagnetic valve
5. 8 LED Tachometer display for changing control valve capacity, - / +
Technical Data:
• Voltage supply: 11 to 15 Volt
• Temperature to use -10°C to 40°C
• Storage temperature -20°C to +50°C
• Power consumption max. 3A
• Drives the compressor from 3 to 100%
• Weight: ca. 600 Gram
• CE and EMV approved
PAGE 2 OF 9
CLT-1 Connections
A.) 2 Pin plug port for the B.) 3 pin Plug for the vehicle
Compressor control valve harness. 12v battery power supply.
General Information:
• Please read the User Manual prior to connecting to the Vehicle A/C Compressor.
• The Technician using the CLT-1 must have good working knowledge
and A/C Diagnostic trouble shooting skills prior to using the CLT-1
• Ideal testing conditions would be a temperature of +15°C,
but the CLT-1 can operate below this temperature.
• Warranty is not covered by Incorrect use and application of the CLT-1
PAGE 3 OF 9
Preparation and set up of the CLT1
Fig. 1(B) Fig. 2(A)
1.) Fig.1 (B) 3-pin port 12v Battery supply cable Harness
2.) Fig. 2 (A) 2-pin port Compressor Control Valve harness 3-Options of Control Valve
connector Harness available,
This illustration shows the combination with the cable of the VAG - group.
I.) Universal 2-pin Cable Harness: Pt No: CLTUNI

(Included in Standard Pt No-CLT-1 Kit)
II.) VAG-Group Harness: Pt No: CLTVAG

Specially Order or included in CLTSET1 & CLTSET2
III.) Denso Control Valve Harness; Pt No; CLTDEN

Special Order or included in CLTSET1 & CLTSET2
IV.) Digital Measuring Unit, Pt No; CLTMU-0170

For measuring the signal output from the vehicle harness
Or included in CLTSET1
V.) Dummy Simulator unit, Pt No; CLTSIM

Plugs into Vehicle harness, while carrying out CLT-1 Tests, prevents faults codes logging on Vehicle
Electronics memory system.
PAGE 4 OF 9
Preparing the CLT-1 prior to connecting to the vehicle:
• Check Vehicle has correct Charge weight in A/C System
• The vehicle should be at operating temperature.
• The operation of the air conditioning system is to be set on maximum cold.
• Set the blower fan set on maximum speed.
• The airflow should be positioned and set at face vent level, and position
a Temperature Probe in the centre allowing you to measure the air outlet temperature.
• Connect a manifold Set or A/C Service station to allow you to view the operating Low & High side
system pressures.
• Disconnect the plug on the A/C Compressor Control Valve or Control Valve Harness,
and connect the appropriate CLT-1 Universal, VAG-Group or Denso Harness.
Fig. 3 Fig. 4
Fig. 3 Shows you the point of connection for a Denso Compressor
Fig. 4 Shows you the point of connecting in a VW Touran with a Sanden compressor.
PAGE 5 OF 9
General Advise:
Observing the correct polarity when connecting the CLT-1 Control valve Harness, And 12v Battery
power supply should be maintained for the protection of the Test equipment and the compressor.
Connecting to the Vehicle Battery
Attach the 12v Battery Clamps to the vehicle Battery observing the Correct Polarity connections,
otherwise the CLT-1 Unit will be damaged.
That means:
Red = positive = plus = 30
Black = negative = ground = 31
• To prevent storing an error code in vehicle electronics fault code memory system, use the simulator
(Pt No: CLTSIM). Connect it to the Original factory Control Valve Harness Block Connector, while you
are Carrying out tests with the CLT-1.
The CLTSIM has a universal 2-pin connector that will fit all vehicle Control valve harness applications.
Single wire vehicle harness should be connected to ground 31 on the simulator box. The CLTSIM can
be ordered separate, and is included in kits CLTSET1 & CLTSET2.
PAGE 6 OF 9
Test procedure :
CLT1 Double click the -minus button until the unit switches off. This is indicated by the LED
Tachometer display no longer being illuminated -zero compressor capacity load.
• Start & run the Vehicle, then increase the idling speed to (~1500 U/min)
• Proceed to Double Click the + Plus button stage by stage, (allowing a 15- second gap between
each stage). This will start to load the Compressor control valve mechanical capacity. Take care
to observe the vehicle A/C operating Low & High side pressures are changing accordingly - on
your manifold gauges.
• Care should be taken, as the High Side pressure can increase during Testing with the CLT-1,
and the Quick start-up operation of Vehicle’s Control Fans will interrupt correct testing of the A/C
Compressors control Valve.
• Always Observe the A/C systems Temperatures & Pressures while Testing with the CLT-1.
Setting on CLT1 Low Pressure Outlet Temp.

Maximum 1,6 +/- 0,5 bar 0°C +/- 3°
Minimum 3 +/- 0,7 bar 10°C +/-3°

It should be noted that the tolerances are compared against Ambient Temperature vs. Compressor
Load conditions, and must be evaluated in Minimum & Maximum stages while testing the compressor.
The changes on the low-pressure side should be similar to the change of the settings on the CLT1.
PAGE 7 OF 9
Measuring of signals in the Vehicle Electronics:
If you want to measure signals from the car you should choose the Digital Measuring instrument.
Pt No CLTMU-0170.
• For this operation please connect the cables direct to the Original factory Control Valve Harness
Block Connector, while you are Carrying out tests with the CLT-1 and the Digital Measuring unit Pt No
CLTMU-0170.
Choose the selection “Hz-%Duty“
Observe & measure the frequency.
The results should be between 300

and 500Hz.
Through press the key “hz - %” you

can now measure the pulse width.
This should be between 20 and
90%, depending upon performance
requirement.
The measuring wires contact at “COM”

and “Hz - %”
For further information – see the

separate user manual for this unit.
Please note image

is for reference use only.
PAGE 8 OF 9
Trouble Shooting possible electrical disturbances when connected to the
Compressor electronic control valve:
If the “OC“ Lamp illuminates:
Illumination of the “OC“ Lamp indicates:
• Poor Control Valve connection

• Control Valve complete interruption (open circuit)
• Control Valve with short-circuit (less than 3 ohm)
If the “OL“ Lamp illuminates:
Illumination the “OL“ Lamp indicates:
• Power consumption of the valve is too high
Compressortech UK Ltd
66-102 Cherrywood Road

Bordesley Green
Birmingham
United Kingdom
B9 4UD
Tel: +44 (0)121 766 5006

Fax: +44 (0)121 772 8397
Email: [email protected]
Web: www.compressortech.co.uk
PAGE 9 OF 9

User Manual: CLT1 - Hand Held A/C Test - Module For Externally Controlled A/C Compressors

Uploaded by

Copyright:

Available Formats

User Manual: CLT1 - Hand Held A/C Test - Module For Externally Controlled A/C Compressors

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User Manual: CLT1 - Hand Held A/C Test - Module For Externally Controlled A/C Compressors

Uploaded by

Copyright:

Available Formats

User Manual

CLT1 – Hand Held A/C Test - Module for externally controlled

CLT-1 Kit Options:

1. Button to increase the compressor voltage

Fig. 1(B) Fig. 2(A)

I.) Universal 2-pin Cable Harness: Pt No: CLTUNI

II.) VAG-Group Harness: Pt No: CLTVAG

III.) Denso Control Valve Harness; Pt No; CLTDEN

IV.) Digital Measuring Unit, Pt No; CLTMU-0170

V.) Dummy Simulator unit, Pt No; CLTSIM

Fig. 3 Shows you the point of connection for a Denso Compressor

Connecting to the Vehicle Battery

Red = positive = plus = 30

Black = negative = ground = 31

Setting on CLT1 Low Pressure Outlet Temp.

Choose the selection “Hz-%Duty“

Observe & measure the frequency.

The results should be between 300

Through press the key “hz - %” you

The measuring wires contact at “COM”

For further information – see the

Please note image

If the “OC“ Lamp illuminates:

Illumination of the “OC“ Lamp indicates:

• Poor Control Valve connection

If the “OL“ Lamp illuminates:

Illumination the “OL“ Lamp indicates:

• Power consumption of the valve is too high

66-102 Cherrywood Road

Tel: +44 (0)121 766 5006

You might also like