Akira ptv-4300

Projection TV
Service Manual
2
CHASSIS: PDT-6
MODEL:
PTV-4300
Model No: PTV-4300

Version 1.0
3
CONTENTS
1 General Description & Safety Instructions ……………………… .4

1.1 General Description …………………………………...……..4
1.2 Maintenance Instructions …………………………………….5
1.3 Electrical Specification ………………………………………5
2 Signal Processing Flow Chart ………………………………… ….6
3 Troubleshooting Charts ……………………………………… ….10
3.1 Safety Precaution ………………………………………… ..10
3.2 Troubleshooting Charts …………………………………… .11
4 Characteristics of Pins of Main ICs .............……………………..14
5 Convergence Adjustment ……………………………………… ..28
5.1 Description of Function Keys on Remote Controller for
Convergence Adjustment ……………………………… …..28
5.2 Convergence Adjustment Procedures ………………………29
6 I2C-bus Data …………………………………………………… ..33
7 Parts List & Replacement Parts List ………………………… ….36
8 Appendix …… …………………………………………………...62
8.1 Printed Circuit Board …………………………………….....62
8.2 Schematic Diagram ……………………………….. ……….64
8.3 Exploded View …………………………………….. ………65
8.4 BPBT Board ……………………………………….. ………66
8.5 Circuit Diagram ……………………………………… …….67
Model No: PTV-4300

Version 1.0
4
1. General Description & Safety Instructions
1.1 General Description
WARNING!
In order to prevent electric shock, do not remove cover.
No user-serviceable parts inside refer servicing to qualified service personnel.
Features
Conventional color TVs apply 50Hz/60Hz alternate scanning and scan a picture in two separate fields,
which results in distinct scanning structural lines and horizontal flicker. As the TVs can display only
25/30 frames of picture per second, it cause wide-range image flicker. The larger the TV screen is, the
more conspicuous the problems are. Therefore, watching this kind of TV, you are susceptible to
eyestrain.
With the world's the state of the art digital inverter technology, our rear projection TV is an improved
product for better performance. With 60Hz progressive scanning, the RPTV can display a whole frame
of picture per scanning and increase display frequency from 25 frames of picture per second to 60. At
the same period of time, the RPTV can scan lines of up to 1250, two times as many as the conventional
TVs. The RPTV removes completely wide range image flicker and horizontal flicker, and offers
sharper and more lifelike pictures.
• Precision vision: With progressive scanning, the RPTV automatically increases vertical
frequency from 50Hz to 60Hz and horizontal frequency from 15625Hz to 31250Hz.
• Automatic white balance correction: The RPTV correct automatically white balance each
power-on, which avoids color distortion due to long time use and delivers consistently vivid
color.
• VGA terminal: You may connect a computer to the VGA terminal on the RPTV and use the
RPTV as a large-screen multimedia display terminal, through which you can surf Internet
and play games.
• Advanced projection tube" High brightness and high-resolution projection tube of the
world's advanced level guarantees high brightness and reliable focus performance.
Other features
• 7" projection tube (3 pieces)
• 470MHz CATV ready
• Multi system/digital NICAM reception
• Theatre and music surround system
• Still picture
• On/off timer
• Wide power voltage range
• Digital frequency synthesized tuner
• Easy operation
• High-contrast and high-luminance black optical screen
• 236(0-~235) programs preset
• Hi-Fi audio system
• DVD VIDEO COMPONENT IN terminals
• No-signal-off
• I2C bus control
• Digital matrix convergence
• Luminous remote controller
• Program swap
Model No: PTV-4300

Version 1.0
5
1.2 Maintenance Instructions
• If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor starts

to come out from the RPTV, immediately unplug the power cord and contact the service
agency as soon as possible.
• High voltage inside! Non-professionals can not open the back cover.
• Do not expose the RPTV to direct sunshine or put it near heat sources.
• Do not put the RPTV in a place subject to moisture and dust or where the rain can reach.
• Set up a lightning arrester when an outdoor antenna is used. Do not turn on the RPTV in
thunder days. At lightning intervals, pull off the power cord and antenna cable.
• Please turn off power supply of the RPTV while outgoing. In ease of the RPTV is not used
for a long period of time, please pull off the power cord and antenna cable.
• Do not put anything on the RPTV, especially objects filled with water or chemical material
on top of the RPTV. Doing so may cause deformation to the cabinet and screen or water to
spill into the RPTV.
• Install the RPTV in a place with good air circulation. Do not cover the ventilating holes to
prevent the RPTV from overheating.
• Avoid hard objects hitting on .the RPTV (especially screen) or severe vibration when
moving the unit. Doing so may adversely affect location of the inside lens.
• To prevent the RPTV from falling off or tip over, place the RPTV on stable and flat surface
without vibration and fix it according to Operation Manual.
• Do not switch the RPTV on and off frequently. Doing so may shorten life span of the RPTV.
• Do not switch on or off the RPTV by plugging or pulling off the plug.
• When using TV games, computers and similar products with your RPTV, keep the
brightness and contrast functions at low setting. If a fixed pattern is left on the screen for a
long period of time, especially at a high brightness or contrast setting, the image can be
permanently imprinted onto the screen, which is not covered by your warranty.
• Wipe the cabinet regularly using only a soft cleaning cloth.
• If the cabinet is particularly dirty, soak a soft cloth in water to which a small amount of
neutral detergent has been added, and dry it to wipe the cabinet. Do not use organic solvent.
• Keep the screen dry. Wipe the screen using a dry soft cloth. Observe the instructions if using
a synthetic rag.
1.3 Electrical Specification

Rated voltage AC 150 ~ 260V, 50Hz / 60Hz
Rated power consumption ~250W
Receiving channels VHF: C1 ~ C12 UHF: C13~C57 CATV: Z1~ Z37
Color system PAL 4.43, PAL 3.58, NTSC 3.58, NTSC 4.43,
SECAM
Sound system D / K, I, M, B/G
Audio output 15W + 15W (THD = 7%)
Model No: PTV-4300

Version 1.0
10
3. Troubleshooting Charts
3.1 Safety Precaution
WARNING:
Service should not be attempted by anyone unfamiliar with the necessary precaution on the RPTV. The
following are the necessary precaution to be observed before servicing.
1. Cold ground near the point to be tested, not warm ground on the power supply board shall be 0
reference when testing voltage at circuit joints.
2. In the process of servicing, do not turn on/off the set quickly and frequently. The minimum
internal shall be more than 30s.
3. Always be certain that the wires are connected or wrapped as it was after completion of servicing.
4. Keep signal and supply wires from high voltage or high temperature components.
5. Be careful and do not scratch the screen and lens when removing the screen.
6. Normally, do not perform any operation (e.g. press VOLUME UP/DOWN buttons) under the item
of "INIT" of Data menu for final adjustment in order to avoid initiating final-ad-justed data.
Product Safety Notice
Many electrical and mechanical parts in this chassis have special safety-related characteristics.
These characteristics are often passed unnoticed by a visual inspection and the protection afforded by
them cannot necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. Replacement parts, which have these special safety characteristics are identified in this
manual and its supplements.
Electrical components having such feature are identified by printing on the schematic diagram and the
part list. Before replacing any of these components, read the part list in this manual carefully.
Unauthorized substitutions may result in fire, electric shock or other hazards.
Model No: PTV-4300

Version 1.0
14
4. Characteristics of Pins of Main ICs
TDA9178
Pinning and external components of the TDA9178:
1 Sc Sandcastle input pin

2 Nc Not connected pin
3 ADextl External AD-conversion #1 input pin
4 ADext2 External AD-conversion #2 input pin
5 Adext3 External AD-conversion #3 input pin
6 Yin Luminance input pin
7 ADR Address selection input pin
8 uin -(B-Y) signal input pin
9 Vin -(R-Y) signal input pin
10 TP Testpin connected to ground
11 SCL I2C.bus: clock input pin
14 SDA I~C-bus: data input pin
15 DECDIG Decoupling digital supply
16 Vout -(R-Y) signal output pin
17 Vout -(B-Y) signal output pin
18 Vee Ground pin
19 Yout Luminance output pin
20 Vee Supply-voltage pin
21 Sout Luminance output for SCAVEM
22 CF Cue-flash output pin
Sc 1 13 Nc
Nc 2 14 Nc
ADext1 3 15 CF
ADext2 4 16 Sout
ADext3 5 17 Vcc
Yin 6 18 Yout
ADR 7 TDA9178 Sc
19 Vee
Uin 8 20 Uout
Vin 9 21 Vout
TP 10 22 DECDIG
SCL 11 23 SDA
Nc 12 24 Nc
Model No: PTV-4300

Version 1.0
19
TDA6111Q
Video output amplifier
General description
The TDA611Q is a video output amplifier with 16 MHz bandwidth. The device is contained in a single
in-line 9-pin medium power (DBS9MPF) package, using high-voltage DMOS technology, intended to
drive the cathode of a color CRT.
Quick reference data

Symbol Parameter Conditions Min. Typ. Max. Unit
VDDH high level supply voltage 0 - 250 V
VDDL low level supply voltage 0 - 14 V
IDDH quiescent high voltage supply VOC=0.5VDDH 7.0 9.0 11.0 mA
current
IDDL quiescent low voltage supply
VOC=0.5VDDH 5.0 6.8 8.0 mA
current
VI input voltage 0 - VDDL V
VOC,
output voltage VDDL - VDDH V
Vfb
Tstg storage temperature -55 - +150 °C
Tamb operating ambient temperature -20 - +65 °C
Pinning
Symbol Pin Description

Vip 1 non-inverting voltage input
VDDL 2 supply voltage LOW
Vin 3 inverting voltage input
GND 4 ground, substrate
Iom 5 black current measurement output
VDDH 6 supply voltage HIGH
Vcn 7 cathode transient voltage output
Voc 8 cathode DC voltage output
Vfb 9 feedback voltage output
Model No: PTV-4300

Version 1.0
20
Vip
1
VDDL
2
Vin
3
GND
4
Icm
5 TDA6111Q
VDDH
6
Vcn
7
Voc
8
Vfb
9
Pin configuration
TDA9181
Integrated multistandard comb filter
Pinning
Symbol Pin Description

CIN 1 chrominance input signal
INPSEL 2 input switch select input
Y/CVBS2 3 luminance or CVBS input signal 2
DGND 4 digital ground
VDD 5 digital supply, voltage
VCC 6 analog supply voltage
SC 7 sandcastle input signal
FSCSEL 8 subcarrier select input
FSC 9 subcarrier input signal
SYS2 10 standard select 2 input
SYS1 11 standard select 1 input
Y/CVBS1 12 luminance or CVBS input signal 1
AGND 13 analog ground (signal reference)
Y/CVBSOUT 14 luminance or CVBS output signal
OUTSEL 15 output switch select input
COUT 16 chrominanee output signal
Model No: PTV-4300

Version 1.0
21
Pin configuration
Table 1: Pin Function, Reference Voltage and Resistance to Ground of TDA9178
Resistance
Pin Static Dynamic to
Short Description
No. Voltage Voltage Ground
1 Sandcastle Pulse Input 0.77 0.77 Infinity

2 Not Connected Pin 0 0 0.1
3 A/D Input 1 0 0 0.1
4 A/D Input 2 0 0 0.1
5 A/D Input 3 0 0 0.1
Inverter YD Luminance Signal
6 1.51 1.47 0.1
Input
7 Ground 0 0 0
Inverter UD Color Difference
8 1.50 1.46 0.1
Signal Input
Inverter VD Color Difference
9 1.51 1.47 0.1
Signal Input
10 Not Connected Pin 0.41 0 0
11 Clock Signal Jumper 3.2 Variant 3.2 Variant 5.8K
12 Not Connected Pin 0 0 0
13 Not Connected Pin 0 0 0
14 Data Signal Jumper 2.9 Variant 3.1 Variant 5.8K
15 De-coupling Capacitor 5.07 5.06 Infinity
V Color Difference Signal Output
16 2.63 2.67 Infinity
after Transient Improvement
U Color Difference Signal Output
17 2.63 2.64 Infinity
after Transient Improvement
18 Ground 0 0 0
Luminance Signal (Y) Output after
19 0.73 0.8 Infinity
Transient Improvement
20 +SV Power Supply +8.01 8.01 0.9K
21 VM Signal Output 2.21 2.27 Infinity
Low Frequency Flicker Detection
22 2.72 0.73 Infinity
Output
23 Ground 0 0 0
24 Ground 0 0 0
Model No: PTV-4300

Version 1.0
22
Table 2: Pin Function, Reference Voltage and Grounding Resistance of TDA9321
Resistance
Short Description
1 Sound IF Signal Processing AGC Filter 2.77 3.11 Infinity

2 Video IF Signal Input 4.65 4.62 69.8K
3 Video IF Signal Input 4.65 4.62 69.8K
4 PIF Amplifier AGC Filter for External Video 1.29 4.01 Infinity
5 2nd Sound IF Signal Output 3.37 3.36 Infinity
Detection Phase-locked Loop Filter for External
Video
7 Connects IF Coil T101 3.81 3.79 Infinity
8 Connects IF Coil T101 3.81 3.79 0
9 Ground 0.11 0.11 3.3K
10 TV Video Signal Output 4.81 3.12 0.9K
11 8V Power Supply 8,13 8.09 Infinity
TV Video Signal Input Processed by Sound
12 3,52 3.94 Infinity
Trapper
TV Video Signal Output Processed by Group
13 2.94 3.37 Infinity
Delay line
14 TV Video Signal. Input 3.57 3,57 Infinity
15 Not Connected Pin 0.51 0.13 88.K
16 Connects Video Signal from AV2 Terminal 3.52 3.51 Infinity
17 Not Connected Pin 0,5 0.13 88.5K
18 CVBS2 Video Signal Input 4.35 3.57 Infinity
19 M System Control Signal Output 4.91 4.91 Infinity
20 Connects Y Luminance Signal from S1 Terminal 3.53 3.51 Infinity
21 Connects Chrominance Signal from S 1 Terminal 0.22 0.22 99.1K
22 Not Connected Pin 0.11 0.11 Infinity
Connects Luminance Signal (Y-3) from $3
23 3,53 3.51
Terminal
Connects Chrominance Signal (C-3) from S3
24 0.22 0 99.0K
Terminal
Outputs Switching Signal SYSI for Controlling
25 0.11 0 Infinity
Comb Circuit
TV/AV Video Signal Output, to Comb Circuit
26 3.44 4 Infinity
SAA4961
Outputs Switching Signal SYS2 for Controlling
27 5.01 5.00 Infinity
Comb Circuit Status
28 Luminance Signal Input from Comb Circuit 3.63 0 Infinity
29 Chrominance Signal Input from Comb Circuit 0.22 0 99.3K
Color Sub-carrier Signal Output, to Comb Circuit
30 4.25 0 Infinity
SAA4961
31 Ground 0.11 0.11 0
33 Power De-coupling Filter Capacitor 5,02 5.01 Infinity
34 Video Signal Output, to AV Output Port 2.19 2.6 Infinity
35 Not Connected Pin 4.12 3.11 37.3K
Connects DVD Jack, Inputs V Color Difference
36 Signal (or External R1 Primary Color Signal 3.29 4.79 Infinity
Input)
Connects DVD jack, Inputs Y Luminance Signal
37 3.31 2.82 Infinity
(or External G1 Primary Color Signal Input)
Fixed Level RGB1 Input with Fast-Blanking input,
39 2.75 2.74 22.0K
Forced into
Model No: PTV-4300

Version 1.0
23
Resistance
Short Description
Connects DVD Jack, Inputs U Color Difference

38 Signal (or Extenaal B1 Primmy Color Signal 3.16 2.80 Infinity
Input)
42 Not Connected Pin 3,36 2.86 Infinity
44 Ground 0.11 0.11 0
45 8V Power Supply 8.17 8.16 0.9K
3.2-3.26
46 I2C Bus Clock Signal Jumper 3.44 5.8K
Variant
2.96-3.12
47 I2C Bus Data Signal Jumper 3.37 5.9K
Variant
Luminance Signal Output, to Inverter Processing
49 2.87 3.46 Infinity
Assembly
U Color Difference Signal Output, to Inverter
50 2.45 2.27 Infinity
Assembly
V Color Difference Signal Output, to Inverter
51 2.43 2.42 Infinity
Assembly
52 Color Phase-demodulation Filter Capacitor (PLL) 4.56 5.05 Infinity
53 SECAM De-modulation Filter Capacitor 4.12 0 Infinity
54 4.43 MHZ Crystal 2.52 2.55 Infinity
58 Line Phase-discriminator 1 Filter Network 3.93 4.18 Infinity
Horizontal Sync. Signal Output HA, to Inverter
60 0.5 0.5 Infinity
Circuit
61 Vertical Sync. Output VA, to Inverter Circuit 0.17 0.16 Infinity
62 Radio AGC Control Voltage Output 6.67 6.77 8.8K
63 Sound IF Signal Input 4.64 4.63 69.8K
64 Sound IF Signal Input 4.64 4.63 69.8K
Model No: PTV-4300

Version 1.0
24
Table 3: Pin Function, Reference Voltage and Grounding Resistance of P87C766 (N002)
Resistance
Pin Static Dynamic
Short Description to
No. Voltage Voltage
Ground
1 PIP Hue Control Output 0.14 0.37 Infinity
2 50/60Hz Control Signal Output 0.14 0.24 Infinity
3 Geomagnetism Con'ection Control Output 0.14 0.46 Infinity
4 Mute Control Signal Output 3.08 0 12.3K
5 VGA2 Protection Mode Setting, High level is active 0 0 0
VGA Sync. Switch Signal Output, Low Level Selects
6 0 0 12.4K
VGA Sync. Signal
7 VGA Identification Signal Input 0 0 52.6K
VGA Protection Signal Input, "PROTECTION" is
displayed when the screen is in protection mode.
9 External Mute Control Output 3.56 4.88 12.4K
10 Button Control Component 5.02 4.88 10.61K
11 Button Control Component 5.02 4.88 10.5K
TV/AV Switching Voltage Output Audio Switching Signal
12 0 0 12.4K
between TV and AV3,
13 Standby/Power-on Control Signal Output 3.82 0 17.3K
15 Not: Connected Pin 0.20 0.41 Infinity
17 Indicator Control Signal Output 0 0 12.7K
18 Sound System Switch Control Signal Output 0 0 12.9K
19 Sound System Control Signal Output 0 0 12.9K
20 Not Connected Pin 0 0.45 Infinity
21 Ground 0 0 0
22 Not Connected Pin 0 0 Infinity
Power Supply +5V to CPU Analog Signal Processing
28 5.03 4.88 2.5K
Circuit
29 Ground 0 0 0
Clock Oscillating Signal Input, Connects 12MHZ Crystal
31 2.02 1.95 Infinity
Oscillator
Clock Oscillating Signal Output, Connects !2MHZ Crystal
32 2.64 5.54 Infinity
Oscillator
33 CPU Reset Pin, High Level Voltage is Active 0 0 47.2K
34 Not Connected Pin 5.02 4186 Infinity
Bus Production Mode Setting, Ex-faetory Mode is High 4.4
35 5.02 17.3K
Level Variant
36 1st Bus Signal Output, Connects Clock Signal 5,02 4.77 5.8K
37 Remote Signal input 4.96 4.82 30.6K
4.72
38 1st Bus Control Output, Connects Data Signal 5.01 5.9K
Variant
2nd Bus Signal Output, Connects Clock Signal, to 3.3
39 5.01 5.8K
controlled Circuit Variant
2nd Bus Signal Output, Connects Data Signal, to 3.1
40 5.01 5.8K
Controlled Circuit Variant
42 CUP+SV Supply Voltage 5.01 4.87 2.5K
Model No: PTV-4300

Version 1.0
25
Table 4: Pin Function, Reference Voltage and Grounding Resistance of

TDA9332H(N005)
Resistance
Pin Static Dynamic
Short Description to
No. Voltage Voltage
Ground
1 Vertical Drive Negative Output A 2.24 2.31 Infinity
2 Vertical Drive Positive Output B 2.26 2.31 Infinity
3 E/W Correction Pulse Output 3.36 3.26 15.0K
4 EHT High Voltage Detection Signal Input 1.54 1.46 16.2K
5 Quick Detection Input 0.07 0.06 Infinity
6 Ground 0 0 0
7 Data Circuit De-coupling 5.00 5.00 Infinity
8 Line Actuating Pulse Output 0.67 6.67 81.5K
Sandcastle Pulse Output, to Color Transient Improving
Circuit TDA9178
3.1
10 2nd Bus Signal Clock Signal Jumper 3.04 5.9
Variant
3.0
11 2nd Bus Signal Data Signal Jumper 2.9 5.9K
Variant
13 Line Retrace Pulse Input 0.60 0.57 Infinity
14 Dynamic Phase Correction Pulse Input 3.56 3.20 67.8K
15 Field Saw tooth Forming Capacitor C507 0 0.03 Infinity
Reference Current Forming Resistor R512 for Field Saw
16 3.89 3.89 39.2K
tooth Generator
49.9K
17 Line Actuating Power Input 8.08 8.06
Charged
18 Connects Regulated Supply Filter Capacitor C510 4.75 4.75 Infinity
19 Ground 0 0 0
Line Voltage-operated Oscillator Crystal C501
20 1.22 1.05 Infinity
(12MHZ)
21 Connects 12MHZ Crystal 1.05 1.07 Infinity
23 Selected VGA or TV/AV Vertical Syne. Signal Input 0.02 0.04 157.5K
24 Selected VGA or TV/AV Horizontal Syne. Signal Input 0.99 0.39 Infinity
26 V Color Difference Signal Input 3.58 3.61 Infinity
27 U Color Difference Signal Input 3.60 3.51 Infinity
28 Y Luminance Signal Input 3.41 3.46 Infinity
29 Ground 0.05 0.04 0
30 VGA Interface for R Primary Color Signal Input (R1) 2.60 2.60 Infinity
31 VGA Interface for G Primary Color Signal Input (G1) 2.60 2.60 Infinity
32 VGA Interface for B Primary Color Signal Input (B1) 2.60 2160 Infinity
RGB1 Input with Blanking Input, Set to High Level,
33 1.98 0.04 1.8K
VGA Signal is Selected to Bus Setting
34 Peak White Limiting Filter Capacitor 0.18 0.18 Infinity
35 R Primary Color Signal Input for Character Display (R2) 3.55 3.54 Infinity
G Primary Color Signal Input: for Character Display
36 3.54 3.54 Infinity
(G2)
37 B Primary Color Signal Input for Character Display (B2) 3.54 3.54 Infinity
38 RGB2 Input with Blanking Input Blkz 0 0 1.0K
39 +SV Power Voltage 8.00 8.0 1.0K
R Primary Color Signal Output, to Final Playback
40 2.50 2.50 3.0K
Circuit
Model No: PTV-4300

Version 1.0
26
G Primary Color Signal Output, to Final Playback 3.0K

41 2.48 2.53
Circuit
B Primary Color Signal Output, to Final Playback 3.0K
42 2.51 2.56
Circuit
43 Auto-Luminance Control Signal input 2.47 2.46 64K Charged
44 Black Current Detecting Signal Input 6.91 6.89 151.5K
Table 5" Pin Function, Reference Voltage and Grounding Resistance of PCA8516
(NO12)
Pin Operating Resistance to

Short Description
No Voltage Ground
1 Not Connected Pin 0.08 166.2K
2 Not Connected Pin 0.08 Infinity
3 Ground 0 0
4 Ground 0 0
5 Connects RC Filtering Network 2.31 Infinity
6 Inverter Vertical Position Pulse Input 0.13 158.2K
7 Inverter Horizontal Position Pulse Input 0.49 Infinity
8 Clock Signal 2.9 Infinity
9 Data Signal 3.1 5.7K
10 Connects 4MHZ Character Crystal Oscillator 2.38 Infinity
11 Connects 4MHZ Crystal Oscillator 2.28 Infinity
12 Ground 0.08 0
13 +5V Character Oscillating Reset Voltage is Active 5 3.4K
14 Ground 0 0
15 Connects 5V 5 2.4K
16 Character R Prilnary Color Signal Output 0.26 6.6K
17 Not Connected Pin 5 158.3K
18 Character G Primary Color Signal Output 0.24 6.5K
19 Not Connected Pin 5 162.0K
20 Character B Primary Color Signal Output 0 6.5K
21 Connects 5V Power Supply 5 2.3K
22 Character Blanking Output 0.26 2.9K
23 Ground 0 0
24 Connects +5V Power 5 2.4K
Model No: PTV-4300

Version 1.0
27
Operating Voltage of Triode

Pos. No. b c e Pos. No. b c e
V201 0 4.9 0 V461 3.45 7.18 2.77
V251 4.3 4.9 4.95 V4.02 0.52 7.75 0
V250 4.92 0 4.95 V462 -10.87 -0.64 -11.47
V672 0.64 0 0 V460 -0.64 -19.27 -0.11
V612 7.57 2.97 7.39 V404 -20.2 126.3 -0.01
V671 0.65 0 0 V1005 0 4.6 0
V673 0.64 0. 0 V801 23.2 27.3 22.6
V102 0.7 0 0 V803 26.0 1,3' 26.6
V104A 2.81 8.12 2.15 V805 1.79 ,1.77 2.45
V103A 3.85 6.14 4.57 V804 0.74 4.95 0.61
V 103 3.87 6.14 4.57 V806 4.92 4.95 4.28
V 104 3,88 7.97 3.22 N803 26.6 -0.1 4.9
V 101 1.43 8.09 0.69 V807 8.7 27.2 8.1
V504 1.58 0.1 0 V802 6.8 36.2 8.1
V502 1.09 0 1.72 V832 5.90 7.55 5.23
V503 5.05 1.68 1.72 V831 5.84 7.6 5.22
Q1 1.23 6.95 0.46
Model No: PTV-4300

Version 1.0
29
5.2 Convergence Adjustment Procedures
Note: When performing after-sales service or repair, you usually need only to fine-adjust the crosshatch
in red and blue and make them be lined with green crosshatch on the basis of green crosshatch. It is no
necessary to perform other adjustments.
CONVERGENCE ADJUSTMENT
Notes: In the convergence mode, if the first two displayed characters are "P", it means PAL, and if "Q",
it means NTSC. In the two modes of DVD, the character display is the same as the two above-
mentioned modes. "V" stands for VGA mode. These characters are omitted in the following OSD
display description.
CONVERGENCE ADJUSTMENT IN PAL
I With receiving of PAL signal, and the volume to 0, press and hold MUTE button until the red
"MUTE" character becomes three colors (or white), then press MENU button on front panel of
TV to enter "S" mode (Press "S" button on the jig to enter "S" mode directly when in
production). Press yellow RECALL button to enter the phase of convergence adjustment, and the
red convergence crosshatch displays in the screen. Press DISPLAY button to switch into green
crosshatch signal.
Note" Generally speaking, you can go to Step IV, V, VI and VII directly.
1 Press TEXT button to clear fine/coarse adjusted data of the six channels in the RAM of con-
vergence IC.
Note: Normally speaking, do not reset the RPTV to 0. If it is necessary, exit convergence mode
and time it before your resetting.
2 Adjustment of static convergence in green. Press PIP button until the video image super-
imposes crosshatch testing signal. Press PICTURE MODE SELECTION button until char-
acter "DCGH" appears, then press POSITION UP/DOWN buttons to call up "DCGH"("
DCGV"). Press VOLUME UP/DOWN buttons to make the center of green line (field) of 5-
CH video test pattern locate at the center of the screen. Then press PIP button to conceal the
video image.
II Phase adjustment
a. Adjustment of H. fine adjustment and phase of horizontal test
i. Instate of crosshatch in green, press PICTURE MODE SELECTION button to call
up " FINE NODE", and press SWAP button to switch the cursor into green. Press
MUTE button until "P LOCK" appears. Now press POSITION UP button to
display the GV value of fine adjusted convergence at H#4/V#4 point as the
maximum value on the screen.
ii. Press AV button to call up "FINE PHASE", Press VOLUME UP/DOWN buttons
to make the peak appear at the vertical line at the right of horizontal center.
iii. Press AV button to call up "TEST PHASE". Adjust VOLUME UP/DOWN button
to make the cursor locate at the peak.
iv. Reset GV value at H#4/V#4 to "0".
Model No: PTV-4300

Version 1.0
30
b Setting of start lines of fine-adjusted convergence (setting of STARTLINES)

i In the state of crosshatch in green, press PICTURE MODE SELECTION button to
enter "FINE MODE", then press VOLUME UP/DOWN buttons to set the GH fine
adjustment value at H#4/V#4 as maximum, and make the peak displays on the
screen.
ii Press AV button to call up "STARTLINES", then press VOLUME UP/DOWN
buttons till the peak displays at the center of the field. (Note: "START LINES" value
can only be odd number).
iii Return the GH fine adjusted value at H#4/V#4 to "0".
c Press PICTURE MODE SELECTION button to display "DCRH". Press POSITION UP/
DOWN buttons to call up "KGV3", and press VOLUME DOWN button to set KGV3 as a
larger data. If the cursor is off the horizontal center, press AV button to call up "COAR
PHASE", then press VOLUME UP/DOWN buttons to return the cursor to the original
position.
d Press PICTURE MODE SELECTION button until "DCRH" displays on the screen. Press
POSITION UP/DOWN buttons to call up "KGH3", and adjust VOLUME UP/DOWN but-
tons to set "KGH3" as a larger data. If the cursor is off the field center, press AV button to
call up "START VALUE", then press VOLUME UP/DOWN buttons to return the cursor to
the original position.
e "COUNTUP" Setting
i Press and hold AV button till "COUNTUP" appears, and press VOLUME
UP/DOWN buttons to make crosshatch signal basically be straight in the V/H
direction. (The recommended COUNTUP data: PAL 3D, and NTSC 3D.
III Coarse-adjustment of convergence in green

Press PICTURE MODE SELECTION button till "DCRH" appears, then press POSITION
UP/DOWN buttons to select coarse adjustment order as follows:
i Trim horizontal skew in green (KGH3).
ii Trim green horizontal pincushion distortion (KGH1)
iii Trim green horizontal amplitude (KGH2).
iv Trim green field pincushion distortion (KGV2).
v Trim field keystone distortion (KGV1).
vi Trim green field skew (KGV3).
IV Fine-adjustment of convergence in green

a Press PICTURE MODE SELECTION button to call up "FINE MODE", press SWAP but
line to turn the cursor into green. Press DIGIT SELECTION button to select the point or
line adjustment. Press MUTE button to move or fix the cursor: (When OSD is "POINT
MOVE" or "LINE MOVE", press VOLUME UP/DOWN or POSITION.UP/DOWN buttons
to move the cursor up, down, left and right. When OSD is "POINT LOCK" or "LINE
LOCK", press VOLUME UP/DOWN or POSITION UP/DOWN buttons to adjust the dot or
line data).
Notes:
• In the process of fine adjustment, the cursor will change into 3 colors automatically. Press
MUTE button after adjusting a data, the cursor will return to original color.
• It is recommended to perform trimming fine errors from the center of the screen toward out-
side area in circumference in accordance with such an order as whirlpool-shape. In other
word, at first, trim fine error at the point of H#4/V#4 of the screen center, next trim each fine
point in circumference around outside of the 8 points, then trim other points in the same
way.
Model No: PTV-4300

Version 1.0
31
• If adjusting one point to increase fine error of nearby ones, which are not adjusted, you
should adjust the data at your target point to make the error of nearby ones in the permissible
range. Otherwise the fine adjustment data of nearby point might not meet the requirement
even if the data reaches maximum.
• You can save the adjusted data by pressing MENU button. When OSD displays "DATA
OK", the data is saving, and when " DATA OK" disappears, it indicates the saving is com-
plete.
• When adjusting the parameters of coarse and fine adjustment in green, it will activate the
convergence of the other two guns at the same time.
V Adjustment of convergence in red

a In convergence mode, press DISPLAY button to switch crosshatch state into red and green.
i Adjustment of static convergence in red, adjust "DCRH" and "DCRV" of coarse
adjustment convergence, so that superimpose the center of line-field in red with center
of line-field in green.
ii Trim horizontal skew in red (KRH2)
iii Trim horizontal linearity distortion in red (KRH1)
iv Trim horizontal amplitude in red (KRH3)
v Trim field keystone in red (KRV1)
vi Trim field skew in red (KRV2)
vii Adjusting procedures of fine adjustment data in red is the same as that in green, but
crosshatch on the screen is yellow.
VI Adjustment of convergence in blue

a In convergence state, press DISPLAY button so that crosshatches in red and blue appear on
the screen, and press PIP button to make the cursor become blue.
b Adjustment of static convergence in blue. Press and hold PICTURE NODE SELECTION
button until "DCBH" appears, Press POSITION UP/DOWN buttons to call up "DCBH" and
"DCBV", and press VOLUME UP/ DOWN buttons to position the line-field center of
convergence in blue at the center of screen.
c Trim horizontal skew in blue (KBH2),
d Trim horizontal linearity distortion in blue (KBH1).
e Trim horizontal amplitude in blue (KBH3).
f Trim field keystone in blue (KBVI).
g Trim field skew in blue (KBV2).
VII Saving
a Press MENU button to save the adjusted data.
b Press STILL/MOVABLE PICTURE ADJUSTMENT button to copy the adjusted data to the
corresponding mode of DVD.
CONVERGENCE ADJUSTMENT IN OTHER MODES

Repeat the above-mentioned procedures for NTSC and VGA.
CONVERGENCE ADJUSTMENT IN DVD MODE

In DVD mode, it requires fine trimming PAL and NTSC.
Model No: PTV-4300

Version 1.0
32
ADJUSTMENT OF DYNAMIC FOCUS

1. In convergence adjustment mode, press AV button to call up "HDF PHASE", and adjust it to be a
proper data (usually a smaller data).
2. Connect oscilloscope to the 7th foot on convergence board XS507. Press PICTURE MODE
SELECTION button to call up "DCRH", and POSITION UP/DOWN buttons to "KDFI". Make
horizontal parabola waveform 0 by pressing VOLUME UP/DOWN buttons. Press AV button to
call up "KDF2" and press VOLUME UP/DOWN buttons to adjust the range of field parabola
waveform till the desired picture is obtained. The following is the wave-form of field dynamic
focus:
Model No: PTV-4300

Version 1.0
33
6. I2C – bus Data

Table of Adjustment Parameters
PAL(TV) PAL(AV) PAL(DVD) NTSC(TV) NTSC(AV) NTSC(DVD) VGA
MIF 3F 3F
MAG 16 16
MYFP 07 MYFN 08
MYG 00 00 00 00 00
XTAL 09 09 09 09 09 09 09
TYD 04 04 04 04 04 04 04
TVG 25 25 25 25 25 25 25
TDS 01 01 01 01 01 01 01
TDSA 01 01 01 01 01 01 01
TDSW 01 01 01 01 01 01 01
TDSS 01 01 01 01 01 01 01
TGEG 01 01 01 01 01 01 01
TGEW 01 01 01 01 01 01 01
TGES 01 01 01 01 01 01 01
TBSG 01 01 01 01 01 01 01
TBSS 01 01 01 01 01 01 01
TABS 20 20 20 20 20 20 20
TNLG 20 20 20 20 20 20 20
TS 30 30 30 30 30 30 30
TLW OA OA OA OA OA OA OA
TCTI 01 01 01 01 01 01 01
COON 30 30 30 30 30 30 30
HCDL 04 04 04 04 04 04 04
HSCL 02 02 02 02 02 02 02
HPWL 08 08 08 08 08 08 08
HAKB 00 00 00 00 00 00 00
HWPR 16 16 16 16 16 16 16
HWPG 30 30 30 30 30 30 30
HWPB 32 32 32 32 32 32 32
HBOR 03 03 03 03 03 03 03
HBOG 06 06 06 06 06 06 06
HBLU 01 01 01 01 01 01 01
HBLA 01 01 01 01 01 01 01
MCON 30 30 30 30 30 30 30
Model No: PTV-4300

Version 1.0
34
PAL PAL PAL NTSC NTSC NTSC

VGA
(TV) (AV) (DVD) (TV) (AV) (DVD)
PVSL 23 23 23 QVSL 24 QVSL 24 QVSL 24 VVA 0D
PVA 12 12 12 QVA 16 QVA 16 QVA 16 VVS 20
PVS 20 PVS 20 20 QSC 14 QSC 14 QSC 14 VSC 14
PSC 14 PSC 04 04 QVS 20 QVS 20 QVS 20 VVZ 19
PVZ 19 PVZ 19 19 QVZ 19 QVZ 19 QVZ 19 VVC IF
PVC IF IF IF QVC IF QVC IF QVC IF VVW 16
PVW 16 16 16 QVW 16 QVW 16 QVW 16 VEWW 21
PEWW 24 24 24 QEWW 28 QEWW 28 QEWW 28 VSLB 08
PSLB 08 08 08 QSLB 08 QSLB 08 QSLB 08 VHS 20
PHS 20 20 20 QHS 20 QHS 20 QHS 20 VEWP IB
PEWP 21 21 21 QEWP 20 QEWP 20 QEWP 20 VEWC 25
PEWC IF IF IF QEWC 15 QEWC 15 QEWC 15 VEWL 0D
PEWL 23 23 23 QEWL 1D QEWL 1D QEWL 1D WEWT 33
PEWT 31 31 31 QEWT 2 D QEWT 2 D QEWT 2 D VHP 06
PHP 06 06 06 QHP 0A QHP 0A QHP 0A VHB 08
PHB 0C 0C 0C QHB OA QHB OA QHB OA VEWE 28
PEWE 28 08 08 QEWE 28 QEWE 28 QEWE 28 N/A
OH 06 06 06 OH 06 OH 06 OH 06 OH 06
POV 04 04 04 QOV 04 QOV 04 QOV 04 QOU 06
DIMO 00 00 00 00 00 00 00
OP1 FC FC FC FC FC FC FC
OP2 6A 6A 6A 6A 6A 6A 6A
SPNI 02 N/A N/A 02 N/A N/A N/A
SPSC 01 N/A N/A 01 N/A N/A N/A
SSCH 02 N/A N/A 02 N/A N/A N/A
SFM1 05 N/A N/A 05 N/A N/A N/A
SFM2 01 N/A N/A 01 N/A N/A N/A
SUBV 25 25 25 25 25 25 25
SUVM 4A 4A 4A 4A 4A 4A 4A
SUBB 1C 1C IC IC IC IC IC
SUBM 2C 2C 2C 2C 2C 2C 2C
SUBC 25 25 25 25 25 25 25
SUCM 3F 3F 3F 3F 3F 3F 3F
SCOL 20 20 20 20 20 20 20
SPLL 14 14 14 14 14 14 14
PALS 92 92 92 NASL 8C NASL 8C NASL 8C N/A
PHSP 46 46 46 NHSP 50 NHSP 50 NHSP 50 N/A
PHSP 46 46 46 N/A
PHBP 46 46 46 NHBP 40 NHBP 40 NHBP 40 N/A
PHAP AF AF AF NHAP AF NHAP AF NHAP AF N/A
PVSP 04 04 04 NVSP 04 NVSP 04 NVSP 04 N/A
PVBP IF IF IF NVBP 16 NVBP 16 NVBP 16 N/A
PVAP 78 78 78 NVAP 79 NVAP 79 NVAP 79 N/A
RE80 06 06 06 06 06 06 06
RE81 10 10 10 10 10 10 10
RE82 20 20 20 20 20 20 20
RE83 40 40 40 40 40 40 40
RE84 56 56 56 56 56 56 56
RE85 60 60 60 60 60 60 60
RE86 76 76 76 76 76 76 76
RE8D 05 05 05 05 05 05 05
RE8E 09 09 09 09 09 09 09
RE8F 03 03 03 03 03 03 03
Model No: PTV-4300

Version 1.0
35
TIME OA OA OA OA OA NLSD, 2E OA
DCTI F8 F8 F8 F8 F8 NDHS, 2S F8
SAT 46 46 46 46 46 TIME, 0A 46
PVSD 00 00 00 NVSD 00 NVSD 00 NVSD 00 N/A
MVA 12 12 12 12 12 12 12
PLSD 38 N/A N/A DCTI, F8 N/A
PDHS 22 N/A N/A SAT, 46 N/A
VISTART 0 1 1 1 1 1 1
VICOVNT
31 30 30 30 30 30 30
UP
STARTLI
7 57 57 57 57 57 57
NES
PINEPHA
207 208 208 205 208 207 208
SE
COARPH
18 18 18 18 18 18 18
ASE
HDF
42 4 4 19 4 19 19
PHASE
TEST
69 68 68 75 68 69 68
PHASE
Note:
Items with “V” are adjustable, and the parameters are subject to individual TV. Do not change
parameters of items without “V”.
Model No: PTV-4300

Version 1.0
36
7. Parts List & Replacement Parts List
POSITION NAME TYPE

R601 Carbon film resistor RT13-0.1.66W-2.2 Ohm J
R603 Carbon film resistor RT13-0.166W-2.2 Ohm J
R11.0 Carbon film resistor RT13-0.166W-27 Ohm J
R151 Carbon film resistor RT13-0.166W-47 Ohm J
R101A Carbon film resistor RT13-0.166W- 100 Ohm J
R120 Carbon film resistor RT13-0.166W- 100 Ohm J
R193A Carbon film resistor RT13-0.166W-100 Ohm J
Model No: PTV-4300

Version 1.0
37
POSITION NAME TYPE

R115 Carbon film resistor RT13-0.166W- 1K Ohm J
R135A Carbon film resistor RT13-0.166W- 1K Ohm J
R108 Carbon film resistor RT13-0.166W- 1.2K Ohm J
R105 Carbon film resistor RT13-0.166W-2.2K Ohm J
R111A Carbon film resistor RT13-0.166W-2.2K Ohm J
R100A Carbon film resistor RT13-0.166W-10K Ohm J
R112 Carbon film resistor RT13-0.166W-10K Ohm J
Model No: PTV-4300

Version 1.0
38
POSITION NAME TYPE

W204 Carbon film resistor RTB- 1/6W- 10K Ohm J
R541 Carbon film resistor RT13-0.166W-1M Ohm J
R133A Carbon film resistor RT13-0.166W-2.2M Ohm J
R512 Metal film resistor RJ14-0.25W-39K Ohm G
RP501 Glass enamel film resistor WI06-2Y-0.125W-5K Ohm-A
R831 Direct fuse PRF2000F008
R837 Direct fuse PRF2000F008
C526 Ceramic capacitor CC1-63V-06a-C-2PFC
C132 Ceramic capacitor CC1-63V-06a-C-9PFD
C157 Ceramic capacitor CC1-63V-06a-C-18PFG
C523B Ceramic capacitor CC1-63V-06a-C-18PFG
Model No: PTV-4300

Version 1.0
39
POSITION NAME TYPE

C126 Ceramic capacitor CC1-63V-06a-C-27PFJ
C123 Ceramic capacitor CC1-63V-06a-SL-100PFK
C130 Ceramic capacitor CC1-63V-10a-SL-330PFK
C536 Ceramic capacitor CT1-63V-06a-2B4-470PFK
C112A Ceramic capacitor CT1-63V-06a-2B4-1000PFK
C201K Ceramic capacitor CT1-63V-06a-2B4-1000PFK
C202K Ceramic capacitor CT1-63V-06a-2B4-1000PFK
VD507 Ceramic capacitor CT1-63V-06a-2B4-1000PFK
VD508 Ceramic capacitor CT1-63V-06a-2B4-1000PFK
C102 Ceramic capacitor CT1-63V-08a-2F4-10nFZ
C504A Ceramic capacitor CT1-63V-08a-2F4-10nFZ
C264 Polyester film capacitor CL21X-50V-0.033uFJ
C123A Polyester film capacitor CL21X-50V-0.1uFJ
Model No: PTV-4300

Version 1.0
40
POSITION NAME TYPE

C507 Polyester film capacitor 2222-336-76104
C135B Polyester film capacitor CL21X-50V-0.33uFJ
C129 Aluminium electrolytic capacitor CD 110-50V-1uFM
C128 Aluminium electrolytic capacitor CD 110-50V-2.2uFM
C250 Aluminium electrolytic capacitor CD110-50V-10uFM
Model No: PTV-4300

Version 1.0
41
POSITION NAME TYPE

C101 Aluminium electrolytic capacitor CD 110X-16V-100uFM
C603 Aluminium electrolytic capacitor CD 110X-25V-l00uFM
L105 Fixed inductor COLTRF4229AJ
L106 Fixed inductor LGA0204-2.2uHJ
L109 Fixed inductor LGA0204-0.33uHK
W208 Fixed inductor LGA0307-56uHK
L111 Fixed inductor LGB0606-1.0uHJ
L110A Fixed inductor LGB0606-10uHJ
L115 Fixed inductor LGB0606-10uHJ
L103 Fixed inductor TLN3193-100uHK
L108 Fixed inductor TLN3040D-330uHK
L181B Cored inductor TEM2028K
Model No: PTV-4300

Version 1.0
42
POSITION NAME TYPE

VD101A Diode 1N4148 (1SS133)
VD102 Diode 1N4148 (1SS133)
VD220 Diode 1N4148 (1SS133)
VD221 Diode 1N4148 (1SS133)
VD222 Diode 1N4148 (1SS133)
VD223 Diode 1N4148 (1SS133)
VD260 Diode 1N4148 (1SS133)
VD501 Diode 1N4148 (1SS133)
VD502A Diode 1N4148 (1SS133)
VD503 Diode 1N4148 (1SS133)
VD505 Diode 1N4148 (1SS133)
VDS10 Diode 1N4148 (1SS133)
VD511 Diode 1N4148 (1SS133)
VD531A Diode 1N4148 (1SS133)
VD532B Diode 1N4148 (1SS133)
VD601 Diode 1N4148 (1SS133)
VD602 Diode 1N4148 (1SS133)
VD604 Diode 1N4148 (1SS133)
VD605 Diode 1N4148 (1SS133)
VD606 Diode 1N4148 (1SS133)
VD607 Diode 1N4148 (1SS133)
VD608 Diode 1N4148 (1SS133)
VD609 Diode 1N4148 (1SS133)
VD250 Diode W05Z3.6A
VD506 Diode W05Z5.6C
VD504 Diode W05Z6.8B
VD509 Diode W05Z12A
V250 Transistor 2SA1015-Y(3CG1015-Y; 2SA933AS,Q)
V102 Transistor 2SC1815-Y(3DG1815-Y; 2SC1740S,Q)
V103A Transistor 2SC1815-Y(3DG1815-Y; 2SC1740S,Q)
V104A Transistor 2SC1815-Y(3DG1815-Y; 2SC1740S,Q)
V101 Transistor 2SC388ATM(KSC388C-Y; 3D388ATM)
V504 Transistor RN1204
V671 Transistor 2SC2878-A
V831 Transistor 2SC3852(2SD 1944H)
Z111 Ceramic filter TPS4.5MB
Zl14 Ceramic filter TPS6.5MB
Model No: PTV-4300

Version 1.0
43
POSITION NAME TYPE

G108 Crystal oscillator JA18A1-3.579545MHZ
G105 Crystal oscillator JA18A1-4.433419MHZ
G202 Crystal oscillator JA18A-4.00MHZ
G201 Crystal oscillator JA18A-12.000MHZ (KL120005ACZ)
G501 Crystal oscillator JA18A-12.000MHZ (KL120005ACZ)
T101 IF transformer ST6022
Z001 SAWF K6286K
Z002 SAWF K9252M
U002 Tuner ENV59D29G3
N002 Integrated circuit P87C766BDR/03
N012 Integrated circuit PCA8516P/036
N003 Integrated circuit TDA9181P/NIB
N006 Integrated circuit TDA8200AH
N005 Integrated circuit TDA9332H(2Y)
N001 Integrated circuit TDA9321H(2Y)
VD110 Integrated circuit uPC574J(CW574CS)
N011 Integrated circuit AT24C16
N010 Integrated circuit 74HC157N
N007 Integrated circuit HEF4052BP
N008 Integrated circuit 74HCT4538N
N009 Integrated circuit 74HCT4538N
N004 Integrated circuit TDA9178
N834 Integrated circuit SI-3090CA
Model No: PTV-4300

Version 1.0
44
POSITION NAME TYPE

R450 Metal oxide film resistor RY21-0.5W-1.2 Ohm J
R429 Metal oxide film resistor RY21-0.5W-56 Ohm J
R461 Metal oxide film resistor RY21-0.5W-1.8K Ohm J
R382 Metal oxide film resistor RY21-0.5W-10K Ohm J
R471 Metal oxide film resistor RY21-0.5W-10M Ohm J
R370 Metal oxide film resistor RY21-1W-1 Ohm J
R377 Metal oxide film resistor RY21-1W-1.2 Ohm J
L410 Metal oxide film resistor RY21-1W-10 Ohm J
R451 Metal oxide film resistor RJ20-1W-51K Ohm J
R553 Fusing resistor PRF5000F008
R556 Fusing resistor PRF5000F008
R470 Fusing resistor RF11-2W-1 Ohm J
Model No: PTV-4300

Version 1.0
45
POSITION NAME TYPE

R571A Metal oxide film resistor RY21-2W-47 Ohm J
R417 Wire-wound resistor RXG6-H2-5W-100 Ohm J
C503 Ceramic capacitor CC1-63V-06a-SL-22PFJ
C375 Ceramic capacitor CT1-63V-06a-2B4-1000PFZ
C417 Ceramic capacitor CT1-500V-06c-2B4-390PFK
C499 Ceramic capacitor CT81-2KV-08c-2B4-220PFK
C410 Ceramic capacitor CT81-2KV-12c-2C1-680PFK
C478 Ceramic capacitor CT81-2KV-12c-2R4-1500PFK
Model No: PTV-4300

Version 1.0
46
POSITION NAME TYPE

C381 Polyester film capacitor CL12-100V-0.047uFJ
C445 Polypropylene capacitor CBB 13-200V-0.047uFJ
C466 Polypropylene capacitor CBB 13-630V-8200PFJ
C400 Polypropylene capacitor CF99M4Z102KB
C440 Polypropylene capacitor CBB81-1.6KV-1500PFJ
C385 Aluminium electrolytic capacitor CD 288H-35V-2200uFQ
C464 Aluminium electrolytic capacitor CDS-100V-10uFM
C448 Aluminium electrolytic capacitor CD288H-160V-33uFM

L442 Fixed inductor TLN3329 (JUB4.757.003)
L461 Fixed inductor TLN3329 (JUB4.757.004)
L401 Cored inductor TEM2011
Model No: PTV-4300

Version 1.0
47
POSITION NAME TYPE

L441 Horizontal linear coil HXT10 (JUB4.756.016, DP5188)
L441 Horizontal linear coil HXT15 (JUB4.756.021, DP4388)
L443 Horizontal amplitude inductor LGT-30uH (JUB4.757.037)
VD306 Diode 2CK75D (1N4148)
VD450 Diode 1S1887
VD467 Diode 2SC1887
VD487 Diode 2SC1887
VD488 Diode 2SC1887
VD370 Diode EU2A
VD371 Diode EU2A
VD406 Diode 2CZRU2
VD460 Diode TVR-1B
YD464 Diode W05Z11B
VD509 Diode W05Z11B
VD505 Diode W05Z24C
VD489 Diode W05Z30B
VD461 Diode ERC20-06
VD404 Diode 5VUZ52
V402 Transistor 2SC2235-0

V501 Transistor 2SA1015-Y
V502A Transistor 2SA1015-Y
V461 Transistor 2SC1815-Y
V504 Transistor 2SCI 815-Y
V460 Transistor 2SB688 (3CA688)
V502 Transistor 2SC3852
V525 Transistor 2SC4686A
N503 Integrated Circuit L7805CV (MC7805CT)
N502 Integrated Circuit L7812CV (MC7812CT)
Model No: PTV-4300

Version 1.0
48
POSITION NAME TYPE

N501 Integrated Circuit L7912CV
N301 Integrated Circuit TDA8351
N504 Integrated Circuit STK392-040
N505 Integrated Circuit STK392-040
T461 Flyback transformer BSC70D1
T401 Line-driving transformer BCT-7
T400 Dynamic focus transformer TLN2168
N511 High tension box TPA6032AH

R880 Carbon film resistor RT13-0.166W-IK Ohm J
R832 Metal oxide film resistor RY21-0.5W-56K Ohm J
R813 Glass enamel film resistor RI40-0.5W-1.5M Ohm J
R833 Metal oxide film resistor RJ20-1W-0.47 Ohm J
RF852 Metal oxide film resistor RY21-2W-0.12 Ohm J
RF856 Metal oxide film resistor RY21-2W-0.12 Ohm J
R832A Metal oxide film resistor RY21-2W-2.2 Ohm J
R816 Metal oxide film resistor RY21-2W-100K Ohm J
R841 Fusing resistor RF10-0.5W- 12 Ohm J
RS01 Glass enamel film resistor VR37 225J (232224290185)
R899 Glass enamel film resistor VR37 825J
RV899 Piezoresistor TNR15G471K300 (MYG15-471K)
RT812 Thermistor B57237-S479-M
RF872 Metal oxide film resistor RY21-2W-100 Ohm J
RF851 Direct fuse PRF5000F008 (PRF50005491)
C869A Ceramic capacitor CC1-63V-08a-C-100PFJ

C831 Ceramic capacitor CT1-63V-08a-2F4-10nPFZ
Model No: PTV-4300

Version 1.0
49
POSITION NAME TYPE

C803 Ceramic capacitor DE1107-1E472MAC250
C804 Ceramic capacitor CT1-500V-12c-2E4-4700PFP
C822 Ceramic capacitor DE0910B471K-KX
C823 Ceramic capacitor DE0910B471K-KX
C824 Ceramic capacitor CT7-400VAC-08a-2B4-470PFM
C893 Ceramic capacitor CT81-2KV-08c-2R4-220PFK
C801 Polypropylene capacitor CBB62-250VAC-0.22uFK
C802 Polypropylene capacitor CBB62-250VAC-0.22uFK
C825 Polypropylene capacitor CBB13-630V-0.01uFH
C844 Aluminium electrolytic capacitor CD110X-16V-101uFM
C863 Aluminium electrolytic capacitor CD288H-16V-3300uFQ
C867 Aluminium electrolytic capacitor CD288H-50V-2200uFQ
C884 Aluminium electrolytic capacitor CD289H-160V-330uFT

Model No: PTV-4300

Version 1.0
50
POSITION NAME TYPE

L883 Fixed inductor TRF9253D- 1.luHK
L885 Fixed inductor TLN3155D-100uHK
VD831A Diode 2CK75D (1N4148)

VD834 Diode 2CK75D
VD835 Diode 2CK75D
VD836 Diode 2CK75D
VD817 Diode W05Z12A
VD819 Diode W05Z12A
VD831 Diode W05Z12C
VD812 Diode W05Z18C
VD821 Diode W05Z1812
VD810 Diode W05Z22C
VD832 Diode W05Z24C
VD818 Diode W05Z30B
VD809 Diode AU01Z
VD813 Diode AU01Z
VD822 Diode AU01Z
VD823 Diode AK03
VD861 Diode RU4A (LF-L1)
VD866 Diode RU4AM (LF-L1)
VD863 Diode EU2A
VD815 Diode SARS01
VD864 Diode FML-G12S
V802 Transistor 2SC2655-Y(C)

V883A Transistor 2SC1815-Y
F801 Delay fuse RT1-20-5A-250V
F802 Delay fuse RT1-20-5A-250V
T801 Filter line TRF3173 (LCL-F11)
T802 Filter line TRF3197 (LCL-F12)
T862 Transformer switch BCK-25502L (JUB4.726.052)
N803 Integrated Circuit L7805CV; MC7805CT
N801 Integrated Circuit STR-F6658B
VQ805 Integrated Circuit SE125N
N804 Photo coupler TLP621GR; HS817
VC801 Gretz rectifier RBV-606, LFA; D6SB60L
Model No: PTV-4300

Version 1.0
51
POSITION NAME TYPE

R966 Carbon film resistor ItT13-0.166W-680 Ohm J
Model No: PTV-4300

Version 1.0
52
POSITION NAME TYPE

R920 Metal oxide film resistor RY21-0.5W- 100 Ohm J

C906 Ceramic capacitor CT1-63V-12e-2B4-5600PFK
C936 Ceramic capacitor CTl-63V-08a-2F4-10nFZ
Model No: PTV-4300

Version 1.0
53
POSITION NAME TYPE

C916 Polytster film capacitor CL11X-50V-0.018uFJ
Model No: PTV-4300

Version 1.0
54
POSITION NAME TYPE

C943 Aluminium electrolytic capacitor CD 110X-16V-47u FM
C336A Aluminium electrolytic capacitor CD 110X-50V-10uFM
C340A Aluminium electrolytic capacitor CD 110X-50V-10uFM
L910 Fixed inductor TGB0606-15uHK

L908 Fixed inductor TGB0606-15uHK
L90! Cored inductor TEM2028K
L902 Cored inductor TEM2028K

VD903 Diode W05ZS.6B

V901 Transistor 2SC1815-Y (3DG 1815-Y)
V902 Transistor 2SC1815-Y (3DG1815-Y)
N300 Integrated Circuit 74HCT86N
N902 Integrated Circuit M5218AP
N903 Integrated Circuit HCF4066BE (MC14066BCP)
N901 Integrated Circuit TDA7429S
PV01 AV jack AV-3S-9PBYUV
PV02 AV jack AV-1-3PK100
PV03 AV jack AV-VGA-2PA
RGY15 Carbon film resistor RT13-0.166W-2.7 Ohm J

RGY17 Carbon film resistor RT13-0.166W-2.7 Ohm J
RGY14 Carbon film resistor RT13-0.166W-18 Ohm J
Model No: PTV-4300

Version 1.0
55
POSITION NAME TYPE

RG35 Carbon film resistor RT13-0.166W-56 Ohm J
RG36 Carbon film resistor RT13-0.166W-56 Ohm J
RG14 Carbon film resistor RT13-0.166W- 100 Ohm J
RGY27 Carbon film resistor RT13-0.166W- 100 Ohm J
RGY28 Carbon film resistor RT13-0.166W- 100 Ohm J
RG08 Carbon film resistor RT13-0.166W-1K Ohm J
RGY07 Carbon film resistor RT13-0.166W-1.2K Ohm J
RG02 Carbon film resistor RT13-0.166W-1.5K Ohm J
RGY13 Carbon film resistor RT13-0.166W-12K Ohm J
RGY24 Carbon film resistor RT13-0.166W-1M Ohm J
RGY30 Metal oxide film resistor RY21-1W-10 Ohm J
RG20 Metal oxide film resistor RY21-1W-33 Ohm J
RG17 Glass enamel film resistor RI40-0.5W-1.5K Ohm K
CG02 Ceramic capacitor CC1-63V-06a-C-12PFJ

CG14 Ceramic capacitor CT1-500V-06c-2B4-560PFK
CGY04 Ceramic capacitor CT1-500V-14c-2B4-4700PFK
CGY06 Ceramic capacitor CT1-500V-14c-2B4-4700PFK
CG08 Polytster film capacitor CL21X-50V-0.022uFJ
CGY 13 Polytster film capacitor CL21X-50V-0.1uFJ
CGY01 Polypropylene capacitor CBB81-1.6KV- 1800PFJ
CG30 Aluminium electrolytic capacitor CD110X-16V-10uFM
CG26 Aluminium electrolytic capacitor CD110X-I 6V-470uFM
CG27 Aluminium electrolytic capacitor CD110X-25V-100uFM
CGY12 Aluminium electrolytic capacitor CD110X-25V-100uFM
CG28 Aluminium electrolytic capacitor CD110-50V-0.47uFM
CG29 Aluminium electrolytic capacitor CD288H-250V-33uFQ
Model No: PTV-4300

Version 1.0
56
POSITION NAME TYPE

CGY02 Aluminium electrolytic capacitor CD288-250V-10uFQ
CGY10 Aluminium electrolytic capacitor CD288-250V-10uFQ
LGY18 Fixed inductor LGB0606-0.33uHJ

LGY01 Cored inductor TEM2011
VDG02 Diode 1N4148 (2CK75D)

VDGY03 Diode 1N4148 (2CK75D)
VDGYI0 Diode 1N4148 (2CK75D)
VDG14 Diode MTZJ13A (W05Z 13A)
VDG18 Diode BAV21
VG05 Transistor 2SC1815-Y (3DG1815-Y)
VGY11 Transistor 2SC1815-Y (3DG1815-Y)
VGY10 Transistor 2SA1015-Y (3CG1015-Y)
VGY13 Transistor 2SA1015-Y (3CG1015-Y)
VGY03 Transistor 2SA1837
VGY04 Transistor 2SC4793
NG02 Integrated circuit TDA6111Q
SG01 GZS CRT socket GZS10-2-108
RB35 Carbon film resistor RT13-0.166W-56 Ohm J

RB08 Carbon film resistor RT13-0.166W-1K Ohm J
RB02 Carbon film resistor RT13-0.166W- 1.5K Ohm J
RB06 Carbon film resistor RT13-0.166W-l.5K Ohm J
RB40 Carbon film resistor RT13-0.166W-3.6K Ohm J
RB20 Metal oxide film resistor RY21-1W-33 Ohm J
RB17 Glass enamel film resistor RI40-0.5W- 1.5K Ohm K
CB02 Ceramic capacitor CC1-63V-06a-C-12PFJ

CB14 Ceramic capacitor CTl-500V-06c-2B4-560PFK
CB08 Polytster film capacitor CL21X-50V-0.022uFJ
CB39 Polypropylene capacitor CBB81-1.6KV-1800PFJ
CB30 Aluminium electrolytic capacitor CD110C-16V-10uFM
CB26 Aluminium electrolytic capacitor CD110X-16V-470uFM
CB27 Aluminium electrolytic capacitor CD110X-25V-100uFM
CB28 Aluminium electrolytic capacitor CD110-50V-0.47luFM
CB29 Aluminium electrolytic capacitor CD288H-250V-33uFQ
Model No: PTV-4300

Version 1.0
57
POSITION NAME TYPE

LB01 Cored inductor TEM2011
VDB01 Diode 1N4148 (2CK75D)

VDB14 Diode MTZJ13A (W05Z13A)
VDB18 Diode BAV21
VB05 Transistor 2SC1815-Y (3DG1815-Y)

NB02 Integrated circuit TDA6111Q
SB01 GZS CRT socket GZS10-2-108
RR35 Carbon film resistor RT13-0.166W-56 Ohm J

RR08 Carbon film resistor RT13-0.166W-1K Ohm J
RR02 Carbon film resistor RT13-0.166W-1.5K Ohm J
RR11 Carbon film resistor RT13-0.166W-68K Ohm J
RR20 Metal oxide film resistor RY21-1W-33 Ohm J
RR17 Glass enamel film resistor RI40-0.5W-1.5K Ohm K
CR02 Ceramic capacitor CC1-63V-06a-C-12PFJ

CR14 Ceramic capacitor CT1-500V-06c-2B4-560PFK
CR08 Polytster film capacitor CL21X-50V-0.022uFJ
CR39 Polypropylene capacitor CBB81-1.6KV-1800PFJ
CR30 Aluminium electrolytic capacitor CD110X-16V-10uFM
CR28 Aluminium electrolytic capacitor CD110-50V-0.47uFM
CR29 Aluminium electrolytic capacitor CD288H-250V-33uFQ
LR01 Cored inductor TEM2011
VDR01 Diode 1N4148 (2CK75D)

VDR14 Diode MTZJ13A (W05Z13A)
VDR18 Diode BAV21
VR05 Transistor 2SC1815-Y(3DG1815-Y)

NR02 Integrated circuit TDA6111Q
SR01 GZS CRT GZS10-2-108
RY14 Carbon film resistor RT13-0.166W-27 Ohm J
RY20 Carbon film resistor RT13-0.166W- 100 Ohm J
LY02 Carbon film-resistor RT13-0.166W- 100 Ohm J
Model No: PTV-4300

Version 1.0
58
POSITION NAME TYPE

RY01 Carbon film resistor RT13-0.166W-1K Ohm J
RY23 Carbon film resistor RT13-0.166W-1.2K Ohm J
RY15 Carbon film resistor RT13-0.166W- 100K Ohm J
RY29 Carbon film resistor RT13-0.166W-1M Ohm J
CY08 Ceramic capacitor CC 1-63V-06a-SL-100PFJ

CY13 Ceramic capacitor CC 1-63V-06a-SL-100PFJ
CY06 Ceramic capacitor CT1-63V-06a-2B4-1500PFK
CY09 Polytster film capacitor CL21X-50V-0.047uFJ
CY21 Aluminium electrolytic capacitor CD110X-50V-10uFM
CY10 Aluminium electrolytic capacitor CD110X-50V-47uFM
LY01 Fixed inductor LGB0606-10uHJ
VDY04 Diode 1N4148; 2CK75D
VY07 Transistor BC547

VY03 Transistor 2SA1015-Y; 3CG 1015-Y
VY 12 Transistor 2SC1815-Y; 3DG1815-Y
VY08 Transistor 2SC2878-A
VY09 Transistor 2SC2878-A

Model No: PTV-4300

Version 1.0
59
POSITION NAME TYPE

C026 Ceramic capacitor CC1-63V-06a-SL-3PFC

C027 Ceramic capacitor CC1-63V-06a-SL-3PFC
C001A Ceramic capacitor CC1-63V-06a-SL-47PFJ
C025A Ceramic capacitor CC1-63V-06a-SL-47PFJ
L002A Fixed inductor LGB0606-12uHJ

L001 Fixed inductor LGB0606-100uHK
V001 Transistor 2SC1815-Y; 3LG1815-Y
N001 Integrated circuit MSP3410D-PP-B4 (PSDIP64)
G001 Transistor oscillator JA18Al-18.432MHZ
RK62 Carbon film resistor RT13-0.166W-100 Ohm J

RK57 Carbon film resistor RT13-0.166W-270 Ohm J
RK60 Carbon film resistor RT13-0.166W-2.2K Ohm J
Model No: PTV-4300

Version 1.0
60
POSITION NAME TYPE

RK53 Carbon film resistor RT13-0.166W-12K Ohm J
RK56 Carbon film resistor RT13-0.166W- 12K Ohm J
CK01 Aluminium electrolytic capacitor CD110-16V-10uFM

CK02 Aluminium electrolytic capacitor CD110-16V-10uFM
VDK04 Diode 1N4148

VDK03 Diode FG5RGD
VK02 Transistor 2SA1015-Y

VK03 Transistor 2SA1015-Y
VK01 Transistor 2SC1815-Y
KK01 Switch paddle KA3L6X7X7.5-22-10
KK02 Switch paddle KA3L6X7X7.5-22-10
XPV01 Front AV jack AV-1S-3P
RM01 Carbon film resistor RT13-0.166W-75 Ohm J

CM01 Aluminium electrolytic capacitor CD 110-16V-47uFM
NK01 Integrated circuit HS0038A2; HS0038B
RB01 Carbon film resistor RY21-2W-3.3K Ohm J

RB02 Carbon film resistor RY21-2W-3.3K Ohm J
CB01 Polytster film capacitor CBB13-400V-0.043uFJ
CB02A Polytster film capacitor CL21X-250V-0.1uFJ
CB02B Polytster film capacitor CL21X-250V-0.1uFJ
LB01 Correction inductor HFT90 (JUB4.756.022)

TB01 Correction transformer BJC-F10 (JUB4.739.011)
RBP01 Jumper 5mm
Convergence board JUC7.820-081
Frequency board JUC7.820-169 (169-1)
High tension cover HV-WR
High tension cover HV-WB
High tension cover HV-WG
Power switch KDC-A04-MU171
Power line RVVZ-** -C69
Audio amplifier YD140-A1-30W-8 Ohm
Audio amplifier YD140-Al-30W-8 Ohm
Audio amplifier YDQG80-A1-10W-8 Ohm
Audio amplifier YDQG80-A1-10W-8 Ohm
Aluminium electrolytic capacitor CD71-50V-3.3uFM
Aluminium electrolytic capacitor CD71-50V-3.3uFM
Magnetic coil ZCAT2032-0930; ZCAT2035-0930A
Model No: PTV-4300

Version 1.0
61
POSITION NAME TYPE

Magnetic coil ZCAT2032-0930; ZCAT2035-0930A
Project barrel (R) P16LNM07RJA; P16LSG03RJA
Project barrel (G) P16LNM07HKA; P16LSG03HKA
Project barrel (B) P16LNM07BMA; P16LSG03BMA
Convergence components MHF116-62A
DY deflect coil DAV4925
High tension capacitor MSC102-01C
VM coil TLHX003
Model No: PTV-4300

Version 1.0
62
8.1 PRINTED CIRCUIT BOARD (PART I)
8.1 PRINTED CIRCUIT BOARD (PART II)
63
8.2 SCHEMATIC DIAGRAM
64
8.3 EXPLODED VIEW
64
65
8.4 BPBT BOARD (PART I)
8.4 BPBT BOARD (PART II)
66
8.5 CIRCUIT DIAGRAM
67
AV BOARD
POWER BOARD
68
SCAN BOARD
IPQ BOARD
69
CONVERGENCE BOARD
70
GY BOARD 71
RY BOARD
NICAM BOARD 72
BY BOARD
73
K BOARD
VM BOARD

Akira ptv-4300

Uploaded by

Copyright:

Available Formats

Akira ptv-4300

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Akira ptv-4300

Uploaded by

Copyright:

Available Formats

Projection TV

Model No: PTV-4300

1 General Description & Safety Instructions ……………………… .4

Model No: PTV-4300

1. General Description & Safety Instructions

1.1 General Description

Model No: PTV-4300

1.2 Maintenance Instructions

• If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor starts

1.3 Electrical Specification

Model No: PTV-4300

Product Safety Notice

Model No: PTV-4300

4. Characteristics of Pins of Main ICs

1 Sc Sandcastle input pin

Model No: PTV-4300

Quick reference data

Symbol Pin Description

Model No: PTV-4300

Integrated multistandard comb filter

Symbol Pin Description

Model No: PTV-4300

Table 1: Pin Function, Reference Voltage and Resistance to Ground of TDA9178

1 Sandcastle Pulse Input 0.77 0.77 Infinity

Model No: PTV-4300

Table 2: Pin Function, Reference Voltage and Grounding Resistance of TDA9321

1 Sound IF Signal Processing AGC Filter 2.77 3.11 Infinity

Model No: PTV-4300

Connects DVD Jack, Inputs U Color Difference

Model No: PTV-4300

Model No: PTV-4300

Table 4: Pin Function, Reference Voltage and Grounding Resistance of

Model No: PTV-4300

G Primary Color Signal Output, to Final Playback 3.0K

Pin Operating Resistance to

Model No: PTV-4300

Operating Voltage of Triode

Model No: PTV-4300

5.2 Convergence Adjustment Procedures

CONVERGENCE ADJUSTMENT IN PAL

Model No: PTV-4300

b Setting of start lines of fine-adjusted convergence (setting of STARTLINES)

III Coarse-adjustment of convergence in green

IV Fine-adjustment of convergence in green

Model No: PTV-4300

V Adjustment of convergence in red

VI Adjustment of convergence in blue

CONVERGENCE ADJUSTMENT IN OTHER MODES

CONVERGENCE ADJUSTMENT IN DVD MODE

Model No: PTV-4300

ADJUSTMENT OF DYNAMIC FOCUS

Model No: PTV-4300

6. I2C – bus Data

Model No: PTV-4300

PAL PAL PAL NTSC NTSC NTSC

Model No: PTV-4300

Model No: PTV-4300

7. Parts List & Replacement Parts List

POSITION NAME TYPE