Lab – Troubleshooting Basic PPP with Authentication

Topology

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8
Lab – Troubleshooting Basic PPP with Authentication

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway

G0/1 192.168.1.1 255.255.255.0 N/A

R1 S0/0/0 (DCE) 192.168.12.1 255.255.255.252 N/A
S0/0/1 192.168.13.1 255.255.255.252 N/A
Lo0 209.165.200.225 255.255.255.252 N/A
R2 S0/0/0 192.168.12.2 255.255.255.252 N/A
S0/0/1 (DCE) 192.168.23.1 255.255.255.252 N/A
G0/1 192.168.3.1 255.255.255.0 N/A
R3 S0/0/0 (DCE) 192.168.13.2 255.255.255.252 N/A
S0/0/1 192.168.23.2 255.255.255.252 N/A
PC-A NIC 192.168.1.3 255.255.255.0 192.168.1.1
PC-C NIC 192.168.3.3 255.255.255.0 192.168.3.1

Objectives
Part 1: Build the Network and Load Device Configurations
Part 2: Troubleshoot the Data Link Layer
Part 3: Troubleshoot the Network Layer

Background / Scenario
The routers at your company were configured by an inexperienced network engineer. Several errors in the
configuration have resulted in connectivity issues. Your manager has asked you to troubleshoot and correct
the configuration errors and document your work. Using your knowledge of PPP and standard testing
methods, find and correct the errors. Ensure that all of the serial links use PPP CHAP authentication, and that
all of the networks are reachable.
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with
Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco
IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used.
Depending on the model and Cisco IOS version, the commands available and output produced might vary
from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the
correct interface identifiers.
Note: Make sure that the routers and switches have been erased and have no startup configurations. If you
are unsure, contact your instructor.

Required Resources
• 3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
• 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)
• 2 PCs (Windows with a terminal emulation program, such as Tera Term)
• Console cables to configure the Cisco IOS devices via the console ports
• Ethernet and serial cables as shown in the topology

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 8
Lab – Troubleshooting Basic PPP with Authentication

Part 1: Build the Network and Load Device Configurations

In Part 1, you will set up the network topology, configure basic settings on the PC hosts, and load
configurations on the routers.

Step 1: Cable the network as shown in the topology.

Step 2: Configure the PC hosts.

Step 3: Load router configurations.

Load the following configurations into the appropriate router. All routers have the same passwords. The
privileged EXEC mode password is class. The password for console and vty access is cisco. All serial
interfaces should be configured with PPP encapsulation and authenticated with CHAP using the password of
chap123.
Router R1 Configuration:
hostname R1
enable secret class
no ip domain lookup
banner motd #Unauthorized Access is Prohibited!#
username R2 password chap123
username R3 password chap123
interface g0/1
ip address 192.168.1.1 255.255.255.0
no shutdown
interface s0/0/0
ip address 192.168.12.1 255.255.255.252
clock rate 128000
encapsulation ppp
ppp authentication chap
interface s0/0/1
ip address 192.168.31.1 255.255.255.252
encapsulation ppp
ppp authentication pap
exit
router ospf 1
router-id 1.1.1.1
network 192.168.1.0 0.0.0.255 area 0
network 192.168.12.0 0.0.0.3 area 0
network 192.168.13.0 0.0.0.3 area 0
passive-interface g0/1
exit
line con 0
password cisco
logging synchronous
login
line vty 0 4

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 8
Lab – Troubleshooting Basic PPP with Authentication

password cisco
login
Router R2 Configuration:
hostname R2
enable secret class
no ip domain lookup
banner motd #Unauthorized Access is Prohibited!#
username R1 password chap123
username r3 password chap123
interface lo0
ip address 209.165.200.225 255.255.255.252
interface s0/0/0
ip address 192.168.12.2 255.255.255.252
encapsulation ppp
ppp authentication chap
no shutdown
interface s0/0/1
ip address 192.168.23.1 255.255.255.252
clock rate 128000
no shutdown
exit
router ospf 1
router-id 2.2.2.2
network 192.168.12.0 0.0.0.3 area 0
network 192.168.23.0 0.0.0.3 area 0
default-information originate
exit
ip route 0.0.0.0 0.0.0.0 loopback0
line con 0
password cisco
logging synchronous
login
line vty 0 4
password cisco
login
Router R3 Configuration:
hostname R3
enable secret class
no ip domain lookup
banner motd #Unauthorized Access is Prohibited!#
username R2 password chap123
username R3 password chap123
interface g0/1
ip address 192.168.3.1 255.255.255.0

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 8
Lab – Troubleshooting Basic PPP with Authentication

no shutdown
interface s0/0/0
ip address 192.168.13.2 255.255.255.252
clock rate 128000
encapsulation ppp
ppp authentication chap
no shutdown
interface s0/0/1
ip address 192.168.23.2 255.255.255.252
encapsulation ppp
ppp authentication chap
no shutdown
exit
router ospf 1
router-id 3.3.3.3
network 192.168.13.0 0.0.0.3 area 0
network 192.168.23.0 0.0.0.3 area 0
passive-interface g0/1
line con 0
password cisco
logging synchronous
login
line vty 0 4
password cisco
login

Step 4: Save your running configuration.

Part 2: Troubleshoot the Data Link Layer

In Part 2, you will use show commands to troubleshoot data link layer issues. Be sure to verify settings, such
as clock rate, encapsulation, CHAP, and usernames/passwords.

Step 1: Examine the R1 configuration.

a. Use the show interfaces command to determine whether PPP has been established on both serial links.
From the show interfaces results for S0/0/0 and S0/0/1, what are possible issues with the PPP links?
i think it´s cuz in the r3 i didn´t configure the ppp properly so maybe that´s the reason but i´m not sure,
even when the instructions are pretty clean i´m usure about it

b. Use the debug ppp authentication command to view real-time PPP authentication output during
troubleshooting.
R1# debug ppp authentication
PPP authentication debugging is on
c. Use the show run interface s0/0/0 command to examine the settings on S0/0/0.

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 8
Lab – Troubleshooting Basic PPP with Authentication

Resolve all problems found for S0/0/0. Record the commands used to correct the configuration.

After correcting the issue, what information does the debug output provide?
i can´t run the show run interface command, because it´s says it´s "Invalid input detected at '^' marker."
eventhe
d. Use when
showi wrote the sentence
run interface correctly
s0/0/1 command to examine the settings on S0/0/1.
Resolve all problems found for S0/0/1. Record the commands used to correct the configuration.

After correcting the issue, what information does the debug output provide?

e. Use the no debug ppp authentication or undebug all command to turn off the debug PPP output.
f. Use the show running-config | include username command to verify the correct username and
password configurations.
Resolve all problems found. Record the commands used to correct the configuration.

Step 2: Examine the R2 configuration.

a. Use the show interfaces command to determine if PPP has been established on both serial links.
Have all links been established? no
If the answer is no, which links need to be examined? What are the possible issues?
i´m not sure why i end up with an Encapsulation HDLC, maybe i made a typo

b. Use the show run interface command to examine links that have not been established.
Resolve all problems found for the interfaces. Record the commands used to correct the configuration.

c. Use the show running-config | include username command to verify the correct username and
password configurations.
Resolve all problems found. Record the commands used to correct the configuration.

d. Use the show ppp interface serial command for the serial interface that you are troubleshooting.
Has the link been established?

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 8
Lab – Troubleshooting Basic PPP with Authentication

Step 3: Examine the R3 configuration.

a. Use the show interfaces command to determine whether PPP has been established on both serial links.
Have all links been established?
If the answer is no, which links need to be examined? What are the possible issues?
i still dunno why but i end up again whit a dhcl instead of a ppp configuration

b. Using the show run interface command to examine on any serial link that has not been established.
Resolve all problems found on the interfaces. Record the commands used to correct the configuration.

c. Use the show running-config | include username command to verify the correct username and
password configurations.
Resolve all problems found. Record the commands used to correct the configuration.

d. Use the show interface command to verify that serial links have been established.
e. Have all PPP links been established? no
f. Can PC-A ping Lo0? no
g. Can PC-A ping PC-C? no
Note: It may be necessary to disable the PC firewall for pings between the PCs to succeed.

Part 3: Troubleshoot the Network Layer

In Part 3, you will verify that Layer 3 connectivity is established on all interfaces by examining IPv4 and OSPF
configurations.

Step 1: Verify that the interfaces listed in the Addressing Table are active and configured with
the correct IP address information.
Issue the show ip interface brief command on all routers to verify that the interfaces are in an up/up state.
Resolve all problems found. Record the commands used to correct the configuration.

Step 2: Verify OSPF Routing

Issue the show ip protocols command to verify that OSPF is running and that all networks are advertised.
Resolve all problems found. Record the commands used to correct the configuration.

Can PC-A ping PC-C? no

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 7 of 8
Lab – Troubleshooting Basic PPP with Authentication

If connectivity does not exist between all hosts, then continue troubleshooting to resolve any remaining
issues.
Note: It may be necessary to disable the PC firewall for pings between the PCs to succeed.

Router Interface Summary Table

Router Interface Summary

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
2801 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
(F0/0) (F0/1)
2811 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 8 of 8