Features

• High-performance, Low-power AVR® 8-bit Microcontroller

• Advanced RISC Architecture
– 130 Powerful Instructions – Most Single-clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 16 MIPS Throughput at 16 MHz
– On-chip 2-cycle Multiplier
• Nonvolatile Program and Data Memories
– 8K Bytes of In-System Self-Programmable Flash
Endurance: 10,000 Write/Erase Cycles
– Optional Boot Code Section with Independent Lock Bits
8-bit
In-System Programming by On-chip Boot Program
True Read-While-Write Operation
with 8K Bytes
– 512 Bytes EEPROM
Endurance: 100,000 Write/Erase Cycles In-System
– 1K Byte Internal SRAM
– Programming Lock for Software Security Programmable
• Peripheral Features
– Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode Flash
– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture
Mode
– Real Time Counter with Separate Oscillator
– Three PWM Channels ATmega8
– 8-channel ADC in TQFP and QFN/MLF package
Eight Channels 10-bit Accuracy
– 6-channel ADC in PDIP package
ATmega8L
Eight Channels 10-bit Accuracy
– Byte-oriented Two-wire Serial Interface
– Programmable Serial USART
– Master/Slave SPI Serial Interface
– Programmable Watchdog Timer with Separate On-chip Oscillator
– On-chip Analog Comparator
• Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal Calibrated RC Oscillator
– External and Internal Interrupt Sources
– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and
Standby
• I/O and Packages
– 23 Programmable I/O Lines
– 28-lead PDIP, 32-lead TQFP, and 32-pad QFN/MLF
• Operating Voltages
– 2.7 - 5.5V (ATmega8L)
– 4.5 - 5.5V (ATmega8)
• Speed Grades
– 0 - 8 MHz (ATmega8L)
– 0 - 16 MHz (ATmega8)
• Power Consumption at 4 Mhz, 3V, 25°C
– Active: 3.6 mA
– Idle Mode: 1.0 mA
– Power-down Mode: 0.5 µA

2486QS–AVR–10/06
Pin Configurations
PDIP

(RESET) PC6 1 28 PC5 (ADC5/SCL)

(RXD) PD0 2 27 PC4 (ADC4/SDA)
(TXD) PD1 3 26 PC3 (ADC3)
(INT0) PD2 4 25 PC2 (ADC2)
(INT1) PD3 5 24 PC1 (ADC1)
(XCK/T0) PD4 6 23 PC0 (ADC0)
VCC 7 22 GND
GND 8 21 AREF
(XTAL1/TOSC1) PB6 9 20 AVCC
(XTAL2/TOSC2) PB7 10 19 PB5 (SCK)
(T1) PD5 11 18 PB4 (MISO)
(AIN0) PD6 12 17 PB3 (MOSI/OC2)
(AIN1) PD7 13 16 PB2 (SS/OC1B)
(ICP1) PB0 14 15 PB1 (OC1A)

TQFP Top View

PC4 (ADC4/SDA)
PC5 (ADC5/SCL)
PC6 (RESET)

PC3 (ADC3)
PC2 (ADC2)
PD2 (INT0)

PD0 (RXD)
PD1 (TXD)
32
31
30
29
28
27
26
25
(INT1) PD3 1 24 PC1 (ADC1)
(XCK/T0) PD4 2 23 PC0 (ADC0)
GND 3 22 ADC7
VCC 4 21 GND
GND 5 20 AREF
VCC 6 19 ADC6
(XTAL1/TOSC1) PB6 7 18 AVCC
(XTAL2/TOSC2) PB7 8 17 PB5 (SCK)
10
11
12
13
14
15
16
9 (T1) PD5
(AIN0) PD6
(AIN1) PD7
(ICP1) PB0
(OC1A) PB1
(SS/OC1B) PB2
(MOSI/OC2) PB3
(MISO) PB4

MLF Top View

PC4 (ADC4/SDA)
PC5 (ADC5/SCL)
PC6 (RESET)

PC3 (ADC3)
PC2 (ADC2)
PD2 (INT0)

PD0 (RXD)
PD1 (TXD)
32
31
30
29
28
27
26
25

(INT1) PD3 1 24 PC1 (ADC1)

(XCK/T0) PD4 2 23 PC0 (ADC0)
GND 3 22 ADC7
VCC 4 21 GND
GND 5 20 AREF
VCC 6 19 ADC6
(XTAL1/TOSC1) PB6 7 18 AVCC
(XTAL2/TOSC2) PB7 8 17 PB5 (SCK)
10
11
12
13
14
15
16
9

NOTE:
(T1) PD5
(AIN0) PD6
(AIN1) PD7
(ICP1) PB0
(OC1A) PB1
(SS/OC1B) PB2
(MOSI/OC2) PB3
(MISO) PB4

The large center pad underneath the MLF

packages is made of metal and internally
connected to GND. It should be soldered
or glued to the PCB to ensure good
mechanical stability. If the center pad is
left unconneted, the package might
loosen from the PCB.

2 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Overview The ATmega8 is a low-power CMOS 8-bit microcontroller based on the AVR RISC
architecture. By executing powerful instructions in a single clock cycle, the ATmega8
achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to
optimize power consumption versus processing speed.

Block Diagram Figure 1. Block Diagram

XTAL1

RESET
PC0 - PC6 PB0 - PB7
VCC
XTAL2

PORTC DRIVERS/BUFFERS PORTB DRIVERS/BUFFERS

GND PORTC DIGITAL INTERFACE PORTB DIGITAL INTERFACE

MUX & ADC

TWI
ADC INTERFACE
AGND

AREF
TIMERS/
PROGRAM STACK OSCILLATOR
COUNTERS
COUNTER POINTER

PROGRAM INTERNAL
SRAM
FLASH OSCILLATOR

INSTRUCTION GENERAL WATCHDOG

OSCILLATOR
REGISTER PURPOSE TIMER
REGISTERS

X
INSTRUCTION MCU CTRL.
Y
DECODER & TIMING
Z

CONTROL INTERRUPT
LINES ALU UNIT

STATUS
AVR CPU REGISTER
EEPROM

PROGRAMMING
LOGIC
SPI USART

+ COMP.
- INTERFACE

PORTD DIGITAL INTERFACE

PORTD DRIVERS/BUFFERS

PD0 - PD7

3
2486QS–AVR–10/06
 The AVR core combines a rich instruction set with 32 general purpose working registers.
All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing
two independent registers to be accessed in one single instruction executed in one clock
cycle. The resulting architecture is more code efficient while achieving throughputs up to
ten times faster than conventional CISC microcontrollers.
The ATmega8 provides the following features: 8K bytes of In-System Programmable
Flash with Read-While-Write capabilities, 512 bytes of EEPROM, 1K byte of SRAM, 23
general purpose I/O lines, 32 general purpose working registers, three flexible
Timer/Counters with compare modes, internal and external interrupts, a serial program-
mable USART, a byte oriented Two-wire Serial Interface, a 6-channel ADC (eight
channels in TQFP and QFN/MLF packages) with 10-bit accuracy, a programmable
Watchdog Timer with Internal Oscillator, an SPI serial port, and five software selectable
power saving modes. The Idle mode stops the CPU while allowing the SRAM,
Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-
down mode saves the register contents but freezes the Oscillator, disabling all other
chip functions until the next Interrupt or Hardware Reset. In Power-save mode, the
asynchronous timer continues to run, allowing the user to maintain a timer base while
the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and
all I/O modules except asynchronous timer and ADC, to minimize switching noise during
ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the
rest of the device is sleeping. This allows very fast start-up combined with low-power
consumption.
The device is manufactured using Atmel’s high density non-volatile memory technology.
The Flash Program memory can be reprogrammed In-System through an SPI serial
interface, by a conventional non-volatile memory programmer, or by an On-chip boot
program running on the AVR core. The boot program can use any interface to download
the application program in the Application Flash memory. Software in the Boot Flash
Section will continue to run while the Application Flash Section is updated, providing
true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-
Programmable Flash on a monolithic chip, the Atmel ATmega8 is a powerful microcon-
troller that provides a highly-flexible and cost-effective solution to many embedded
control applications.
The ATmega8 AVR is supported with a full suite of program and system development
tools, including C compilers, macro assemblers, program debugger/simulators, In-Cir-
cuit Emulators, and evaluation kits.

Disclaimer Typical values contained in this datasheet are based on simulations and characteriza-
tion of other AVR microcontrollers manufactured on the same process technology. Min
and Max values will be available after the device is characterized.

4 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Pin Descriptions

VCC Digital supply voltage.

GND Ground.

Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
XTAL1/XTAL2/TOSC1/TOSC2 bit). The Port B output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port B pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Depending on the clock selection fuse settings, PB6 can be used as input to the invert-
ing Oscillator amplifier and input to the internal clock operating circuit.
Depending on the clock selection fuse settings, PB7 can be used as output from the
inverting Oscillator amplifier.
If the Internal Calibrated RC Oscillator is used as chip clock source, PB7..6 is used as
TOSC2..1 input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set.
The various special features of Port B are elaborated in “Alternate Functions of Port B”
on page 58 and “System Clock and Clock Options” on page 25.

Port C (PC5..PC0) Port C is an 7-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port C output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port C pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset
condition becomes active, even if the clock is not running.

PC6/RESET If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electri-
cal characteristics of PC6 differ from those of the other pins of Port C.
If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on
this pin for longer than the minimum pulse length will generate a Reset, even if the clock
is not running. The minimum pulse length is given in Table 15 on page 38. Shorter
pulses are not guaranteed to generate a Reset.
The various special features of Port C are elaborated on page 61.

Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port D output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port D pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port D also serves the functions of various special features of the ATmega8 as listed on
page 63.

RESET Reset input. A low level on this pin for longer than the minimum pulse length will gener-
ate a reset, even if the clock is not running. The minimum pulse length is given in Table
15 on page 38. Shorter pulses are not guaranteed to generate a reset.

5
2486QS–AVR–10/06
AVCC AVCC is the supply voltage pin for the A/D Converter, Port C (3..0), and ADC (7..6). It
should be externally connected to VCC, even if the ADC is not used. If the ADC is used,
it should be connected to VCC through a low-pass filter. Note that Port C (5..4) use digital
supply voltage, VCC.

AREF AREF is the analog reference pin for the A/D Converter.

ADC7..6 (TQFP and QFN/MLF In the TQFP and QFN/MLF package, ADC7..6 serve as analog inputs to the A/D con-
Package Only) verter. These pins are powered from the analog supply and serve as 10-bit ADC
channels.

6 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Resources A comprehensive set of development tools, application notes and datasheets are avail-
able for download on http://www.atmel.com/avr.

7
2486QS–AVR–10/06
Register Summary
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
0x3F (0x5F) SREG I T H S V N Z C 11
0x3E (0x5E) SPH – – – – – SP10 SP9 SP8 13
0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 13
0x3C (0x5C) Reserved
0x3B (0x5B) GICR INT1 INT0 – – – – IVSEL IVCE 49, 67
0x3A (0x5A) GIFR INTF1 INTF0 – – – – – – 68
0x39 (0x59) TIMSK OCIE2 TOIE2 TICIE1 OCIE1A OCIE1B TOIE1 – TOIE0 72, 102, 122
0x38 (0x58) TIFR OCF2 TOV2 ICF1 OCF1A OCF1B TOV1 – TOV0 73, 103, 122
0x37 (0x57) SPMCR SPMIE RWWSB – RWWSRE BLBSET PGWRT PGERS SPMEN 213
0x36 (0x56) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE 171
0x35 (0x55) MCUCR SE SM2 SM1 SM0 ISC11 ISC10 ISC01 ISC00 33, 66
0x34 (0x54) MCUCSR – – – – WDRF BORF EXTRF PORF 41
0x33 (0x53) TCCR0 – – – – – CS02 CS01 CS00 72
0x32 (0x52) TCNT0 Timer/Counter0 (8 Bits) 72
0x31 (0x51) OSCCAL Oscillator Calibration Register 31
0x30 (0x50) SFIOR – – – – ACME PUD PSR2 PSR10 58, 75, 123, 193
0x2F (0x4F) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 FOC1A FOC1B WGM11 WGM10 97
0x2E (0x4E) TCCR1B ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 100
0x2D (0x4D) TCNT1H Timer/Counter1 – Counter Register High byte 101
0x2C (0x4C) TCNT1L Timer/Counter1 – Counter Register Low byte 101
0x2B (0x4B) OCR1AH Timer/Counter1 – Output Compare Register A High byte 101
0x2A (0x4A) OCR1AL Timer/Counter1 – Output Compare Register A Low byte 101
0x29 (0x49) OCR1BH Timer/Counter1 – Output Compare Register B High byte 101
0x28 (0x48) OCR1BL Timer/Counter1 – Output Compare Register B Low byte 101
0x27 (0x47) ICR1H Timer/Counter1 – Input Capture Register High byte 102
0x26 (0x46) ICR1L Timer/Counter1 – Input Capture Register Low byte 102
0x25 (0x45) TCCR2 FOC2 WGM20 COM21 COM20 WGM21 CS22 CS21 CS20 117
0x24 (0x44) TCNT2 Timer/Counter2 (8 Bits) 119
0x23 (0x43) OCR2 Timer/Counter2 Output Compare Register 119
0x22 (0x42) ASSR – – – – AS2 TCN2UB OCR2UB TCR2UB 119
0x21 (0x41) WDTCR – – – WDCE WDE WDP2 WDP1 WDP0 43
UBRRH URSEL – – – UBRR[11:8] 158
0x20(1) (0x40)(1)
UCSRC URSEL UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL 156
0x1F (0x3F) EEARH – – – – – – – EEAR8 20
0x1E (0x3E) EEARL EEAR7 EEAR6 EEAR5 EEAR4 EEAR3 EEAR2 EEAR1 EEAR0 20
0x1D (0x3D) EEDR EEPROM Data Register 20
0x1C (0x3C) EECR – – – – EERIE EEMWE EEWE EERE 20
0x1B (0x3B) Reserved
0x1A (0x3A) Reserved
0x19 (0x39) Reserved
0x18 (0x38) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 65
0x17 (0x37) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 65
0x16 (0x36) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 65
0x15 (0x35) PORTC – PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 65
0x14 (0x34) DDRC – DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 65
0x13 (0x33) PINC – PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 65
0x12 (0x32) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 65
0x11 (0x31) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 65
0x10 (0x30) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 65
0x0F (0x2F) SPDR SPI Data Register 131
0x0E (0x2E) SPSR SPIF WCOL – – – – – SPI2X 131
0x0D (0x2D) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 129
0x0C (0x2C) UDR USART I/O Data Register 153
0x0B (0x2B) UCSRA RXC TXC UDRE FE DOR PE U2X MPCM 154
0x0A (0x2A) UCSRB RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 155
0x09 (0x29) UBRRL USART Baud Rate Register Low byte 158
0x08 (0x28) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 194
0x07 (0x27) ADMUX REFS1 REFS0 ADLAR – MUX3 MUX2 MUX1 MUX0 205
0x06 (0x26) ADCSRA ADEN ADSC ADFR ADIF ADIE ADPS2 ADPS1 ADPS0 207
0x05 (0x25) ADCH ADC Data Register High byte 208
0x04 (0x24) ADCL ADC Data Register Low byte 208
0x03 (0x23) TWDR Two-wire Serial Interface Data Register 173
0x02 (0x22) TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE 174

8 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Register Summary (Continued)

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
0x01 (0x21) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 – TWPS1 TWPS0 173
0x00 (0x20) TWBR Two-wire Serial Interface Bit Rate Register 171

Notes: 1. Refer to the USART description for details on how to access UBRRH and UCSRC.
2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
3. Some of the Status Flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on
all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions
work with registers 0x00 to 0x1F only.

9
2486QS–AVR–10/06
Instruction Set Summary
Mnemonics Operands Description Operation Flags #Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1
ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1
ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2
SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1
SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1
SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1
SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1
SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2
AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1
ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1
OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1
ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1
EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1
COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1
NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1
SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1
CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1
INC Rd Increment Rd ← Rd + 1 Z,N,V 1
DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1
TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1
CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1
SER Rd Set Register Rd ← 0xFF None 1
MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z,C 2
MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z,C 2
MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z,C 2
FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2
FMULS Rd, Rr Fractional Multiply Signed R1:R0 ← (Rd x Rr) << 1 Z,C 2
FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2
BRANCH INSTRUCTIONS
RJMP k Relative Jump PC ← PC + k + 1 None 2
IJMP Indirect Jump to (Z) PC ← Z None 2
RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3
ICALL Indirect Call to (Z) PC ← Z None 3
RET Subroutine Return PC ← STACK None 4
RETI Interrupt Return PC ← STACK I 4
CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1/2/3
CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1
CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1
CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1
SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3
SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3
SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3
SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3
BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2
BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2
BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2
BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2
BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2
BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2
BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2
BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2
BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2
BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2
BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2
BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2
BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2
BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2
BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2
BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2
BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2
BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2
Mnemonics Operands Description Operation Flags #Clocks

10 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Instruction Set Summary (Continued)

BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2
BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2
DATA TRANSFER INSTRUCTIONS
MOV Rd, Rr Move Between Registers Rd ← Rr None 1
MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1
LDI Rd, K Load Immediate Rd ← K None 1
LD Rd, X Load Indirect Rd ← (X) None 2
LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2
LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2
LD Rd, Y Load Indirect Rd ← (Y) None 2
LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2
LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2
LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2
LD Rd, Z Load Indirect Rd ← (Z) None 2
LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2
LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2
LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2
LDS Rd, k Load Direct from SRAM Rd ← (k) None 2
ST X, Rr Store Indirect (X) ← Rr None 2
ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2
ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2
ST Y, Rr Store Indirect (Y) ← Rr None 2
ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2
ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2
STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2
ST Z, Rr Store Indirect (Z) ← Rr None 2
ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2
ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2
STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2
STS k, Rr Store Direct to SRAM (k) ← Rr None 2
LPM Load Program Memory R0 ← (Z) None 3
LPM Rd, Z Load Program Memory Rd ← (Z) None 3
LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3
SPM Store Program Memory (Z) ← R1:R0 None -
IN Rd, P In Port Rd ← P None 1
OUT P, Rr Out Port P ← Rr None 1
PUSH Rr Push Register on Stack STACK ← Rr None 2
POP Rd Pop Register from Stack Rd ← STACK None 2
BIT AND BIT-TEST INSTRUCTIONS
SBI P,b Set Bit in I/O Register I/O(P,b) ← 1 None 2
CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0 None 2
LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1
LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1
ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1
ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1
ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1
SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1
BSET s Flag Set SREG(s) ← 1 SREG(s) 1
BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1
BST Rr, b Bit Store from Register to T T ← Rr(b) T 1
BLD Rd, b Bit load from T to Register Rd(b) ← T None 1
SEC Set Carry C←1 C 1
CLC Clear Carry C←0 C 1
SEN Set Negative Flag N←1 N 1
CLN Clear Negative Flag N←0 N 1
SEZ Set Zero Flag Z←1 Z 1
CLZ Clear Zero Flag Z←0 Z 1
SEI Global Interrupt Enable I←1 I 1
CLI Global Interrupt Disable I←0 I 1
SES Set Signed Test Flag S←1 S 1
CLS Clear Signed Test Flag S←0 S 1
SEV Set Twos Complement Overflow. V←1 V 1
CLV Clear Twos Complement Overflow V←0 V 1
SET Set T in SREG T←1 T 1
Mnemonics Operands Description Operation Flags #Clocks

11
2486QS–AVR–10/06
Instruction Set Summary (Continued)
CLT Clear T in SREG T←0 T 1
SEH Set Half Carry Flag in SREG H←1 H 1
CLH Clear Half Carry Flag in SREG H←0 H 1
MCU CONTROL INSTRUCTIONS
NOP No Operation None 1
SLEEP Sleep (see specific descr. for Sleep function) None 1
WDR Watchdog Reset (see specific descr. for WDR/timer) None 1

12 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Ordering Information
Speed (MHz) Power Supply Ordering Code Package(1) Operation Range
ATmega8L-8AC 32A
Commercial
ATmega8L-8PC 28P3
(0°C to 70°C)
ATmega8L-8MC 32M1-A
ATmega8L-8AI 32A
8 2.7 - 5.5 ATmega8L-8AU(2) 32A
ATmega8L-8PI 28P3 Industrial
ATmega8L-8PU(2) 28P3 (-40°C to 85°C)
ATmega8L-8MI 32M1-A
ATmega8L-8MU(2) 32M1-A
ATmega8-16AC 32A
Commercial
ATmega8-16PC 28P3
(0°C to 70°C)
ATmega8-16MC 32M1-A
ATmega8-16AI 32A
16 4.5 - 5.5 ATmega8-16AU(2) 32A
ATmega8-16PI 28P3 Industrial
ATmega8-16PU(2) 28P3 (-40°C to 85°C)
ATmega8-16MI 32M1-A
ATmega8-16MU(2) 32M1-A
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.

Package Type
32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

13
2486QS–AVR–10/06
Packaging Information

32A

PIN 1
B
PIN 1 IDENTIFIER

e E1 E

D1
D

C 0˚~7˚

A1 A2 A
L
COMMON DIMENSIONS
(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

A – – 1.20
A1 0.05 – 0.15
A2 0.95 1.00 1.05
D 8.75 9.00 9.25
D1 6.90 7.00 7.10 Note 2
E 8.75 9.00 9.25
Notes: 1. This package conforms to JEDEC reference MS-026, Variation ABA.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable E1 6.90 7.00 7.10 Note 2
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum B 0.30 – 0.45
plastic body size dimensions including mold mismatch.
C 0.09 – 0.20
3. Lead coplanarity is 0.10 mm maximum.
L 0.45 – 0.75
e 0.80 TYP

10/5/2001
TITLE DRAWING NO. REV.
2325 Orchard Parkway
32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness,
R San Jose, CA 95131 32A B
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)

14 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

28P3

D
PIN
1

E1

SEATING PLANE

A1
L B2
B (4 PLACES)
B1
e

COMMON DIMENSIONS
0º ~ 15º REF (Unit of Measure = mm)
C
SYMBOL MIN NOM MAX NOTE

eB A – – 4.5724
A1 0.508 – –
D 34.544 – 34.798 Note 1
E 7.620 – 8.255
E1 7.112 – 7.493 Note 1
B 0.381 – 0.533

Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. B1 1.143 – 1.397
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). B2 0.762 – 1.143
L 3.175 – 3.429
C 0.203 – 0.356
eB – – 10.160
e 2.540 TYP

09/28/01
TITLE DRAWING NO. REV.
2325 Orchard Parkway
28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual 28P3 B
R San Jose, CA 95131 Inline Package (PDIP)

15
2486QS–AVR–10/06
32M1-A

D1

1
0
2
3 Pin 1 ID

E1 E SIDE VIEW

TOP VIEW A3
A2
A1
A
K
0.08 C COMMON DIMENSIONS
P (Unit of Measure = mm)
D2
SYMBOL MIN NOM MAX NOTE
A 0.80 0.90 1.00

1 A1 – 0.02 0.05
P
2 A2 – 0.65 1.00
Pin #1 Notch
(0.20 R) 3
A3 0.20 REF
E2
b 0.18 0.23 0.30

K D 4.90 5.00 5.10

D1 4.70 4.75 4.80
D2 2.95 3.10 3.25
E 4.90 5.00 5.10
b e L
E1 4.70 4.75 4.80

BOTTOM VIEW E2 2.95 3.10 3.25

e 0.50 BSC
L 0.30 0.40 0.50
P – – 0.60
0 – – 12o
Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2. K 0.20 – –

5/25/06
TITLE DRAWING NO. REV.
2325 Orchard Parkway
32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm, 32M1-A E
R San Jose, CA 95131 3.10 mm Exposed Pad, Micro Lead Frame Package (MLF)

16 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Erratas The revision letter in this section refers to the revision of the ATmega8 device.

ATmega8 • First Analog Comparator conversion may be delayed

Rev. D to I • Interrupts may be lost when writing the timer registers in the asynchronous timer
• Signature may be Erased in Serial Programming Mode
• CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when 32 KHz
Oscillator is Used to Clock the Asynchronous Timer/Counter2

1. First Analog Comparator conversion may be delayed

If the device is powered by a slow rising VCC, the first Analog Comparator conver-
sion will take longer than expected on some devices.
Problem Fix/Workaround
When the device has been powered or reset, disable then enable theAnalog Com-
parator before the first conversion.

2. Interrupts may be lost when writing the timer registers in the asynchronous
timer
If one of the timer registers which is synchronized to the asynchronous timer2 clock
is written in the cycle before a overflow interrupt occurs, the interrupt may be lost.
Problem Fix/Workaround
Always check that the Timer2 Timer/Counter register, TCNT2, does not have the
value 0xFF before writing the Timer2 Control Register, TCCR2, or Output Compare
Register, OCR2

3. Signature may be Erased in Serial Programming Mode

If the signature bytes are read before a chiperase command is completed, the sig-
nature may be erased causing the device ID and calibration bytes to disappear. This
is critical, especially, if the part is running on internal RC oscillator.
Problem Fix/Workaround:
Ensure that the chiperase command has exceeded before applying the next
command.

4. CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when

32 KHz Oscillator is Used to Clock the Asynchronous Timer/Counter2
When the internal RC Oscillator is used as the main clock source, it is possible to
run the Timer/Counter2 asynchronously by connecting a 32 KHz Oscillator between
XTAL1/TOSC1 and XTAL2/TOSC2. But when the internal RC Oscillator is selected
as the main clock source, the CKOPT Fuse does not control the internal capacitors
on XTAL1/TOSC1 and XTAL2/TOSC2. As long as there are no capacitors con-
nected to XTAL1/TOSC1 and XTAL2/TOSC2, safe operation of the Oscillator is not
guaranteed.
Problem fix/Workaround
Use external capacitors in the range of 20 - 36 pF on XTAL1/TOSC1 and
XTAL2/TOSC2. This will be fixed in ATmega8 Rev. G where the CKOPT Fuse will
control internal capacitors also when internal RC Oscillator is selected as main clock
source. For ATmega8 Rev. G, CKOPT = 0 (programmed) will enable the internal
capacitors on XTAL1 and XTAL2. Customers who want compatibility between Rev.
G and older revisions, must ensure that CKOPT is unprogrammed (CKOPT = 1).

17
2486QS–AVR–10/06
Datasheet Revision Please note that the referring page numbers in this section are referred to this docu-
ment. The referring revision in this section are referring to the document revision.
History

Changes from Rev. 1. Updated “Timer/Counter Oscillator” on page 32.

2486P- 02/06 to Rev.
2486Q- 10/06 2. Updated “Fast PWM Mode” on page 89.

3. Updated code example in “USART Initialization” on page 138.

4. Updated Table 37 on page 98, Table 39 on page 99, Table 42 on page 117,
Table 44 on page 118, and Table 98 on page 240.

5. Updated “Erratas” on page 17.

Changes from Rev. 1. Added “Resources” on page 7.

2486O-10/04 to Rev.
2486P- 02/06 2. Updated “External Clock” on page 32.

3. Updated “Serial Peripheral Interface – SPI” on page 124.

4. Updated Code Example in “USART Initialization” on page 138.

5. Updated Note in “Bit Rate Generator Unit” on page 170.

6. Updated Table 98 on page 240.

7. Updated Note inTable 103 on page 248.

8. Updated “Erratas” on page 17.

Changes from Rev. 1. Removed to instances of “analog ground”. Replaced by “ground”.

2486N-09/04 to Rev.
2486O-10/04 2. Updated Table 7 on page 29, Table 15 on page 38, and Table 100 on page 244.

3. Updated “Calibrated Internal RC Oscillator” on page 30 with the 1 MHz default

value.

4. Table 89 on page 225 and Table 90 on page 225 moved to new section “Page
Size” on page 225.

5. Updated descripton for bit 4 in “Store Program Memory Control Register –

SPMCR” on page 213.

6. Updated “Ordering Information” on page 13.

Changes from Rev. 1. Added note to MLF package in “Pin Configurations” on page 2.
2486M-12/03 to Rev.
2486N-09/04 2. Updated “Internal Voltage Reference Characteristics” on page 42.

3. Updated “DC Characteristics” on page 242.

18 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

4. ADC4 and ADC5 support 10-bit accuracy. Document updated to reflect this.
Updated features in “Analog-to-Digital Converter” on page 196.
Updated “ADC Characteristics” on page 248.

5. Removed reference to “External RC Oscillator application note” from “Exter-

nal RC Oscillator” on page 29.

Changes from Rev. 1. Updated “Calibrated Internal RC Oscillator” on page 30.

2486L-10/03 to Rev.
2486M-12/03

Changes from Rev. 1. Removed “Preliminary” and TBDs from the datasheet.
2486K-08/03 to Rev.
2486L-10/03 2. Renamed ICP to ICP1 in the datasheet.

3. Removed instructions CALL and JMP from the datasheet.

4. Updated tRST in Table 15 on page 38, VBG in Table 16 on page 42, Table 100 on
page 244 and Table 102 on page 246.

5. Replaced text “XTAL1 and XTAL2 should be left unconnected (NC)” after
Table 9 in “Calibrated Internal RC Oscillator” on page 30. Added text regard-
ing XTAL1/XTAL2 and CKOPT Fuse in “Timer/Counter Oscillator” on page 32.

6. Updated Watchdog Timer code examples in “Timed Sequences for Changing

the Configuration of the Watchdog Timer” on page 45.

7. Removed bit 4, ADHSM, from “Special Function IO Register – SFIOR” on page

58.

8. Added note 2 to Figure 103 on page 215.

9. Updated item 4 in the “Serial Programming Algorithm” on page 238.

10. Added tWD_FUSE to Table 97 on page 239 and updated Read Calibration Byte,
Byte 3, in Table 98 on page 240.

11. Updated Absolute Maximum Ratings* and DC Characteristics in “Electrical

Characteristics” on page 242.

Changes from Rev. 1. Updated VBOT values in Table 15 on page 38.

2486J-02/03 to Rev.
2486K-08/03 2. Updated “ADC Characteristics” on page 248.

3. Updated “ATmega8 Typical Characteristics” on page 249.

4. Updated “Erratas” on page 17.

Changes from Rev. 1. Improved the description of “Asynchronous Timer Clock – clkASY” on page 26.
2486I-12/02 to Rev.
2486J-02/03 2. Removed reference to the “Multipurpose Oscillator” application note and the
“32 kHz Crystal Oscillator” application note, which do not exist.

19
2486QS–AVR–10/06
 3. Corrected OCn waveforms in Figure 38 on page 90.

4. Various minor Timer 1 corrections.

5. Various minor TWI corrections.

6. Added note under “Filling the Temporary Buffer (Page Loading)” on page 216
about writing to the EEPROM during an SPM Page load.

7. Removed ADHSM completely.

8. Added section “EEPROM Write during Power-down Sleep Mode” on page 23.

9. Removed XTAL1 and XTAL2 description on page 5 because they were already
described as part of “Port B (PB7..PB0) XTAL1/XTAL2/TOSC1/TOSC2” on
page 5.

10. Improved the table under “SPI Timing Characteristics” on page 246 and
removed the table under “SPI Serial Programming Characteristics” on page
241.

11. Corrected PC6 in “Alternate Functions of Port C” on page 61.

12. Corrected PB6 and PB7 in “Alternate Functions of Port B” on page 58.

13. Corrected 230.4 Mbps to 230.4 kbps under “Examples of Baud Rate Setting”
on page 159.

14. Added information about PWM symmetry for Timer 2 in “Phase Correct PWM
Mode” on page 113.

15. Added thick lines around accessible registers in Figure 76 on page 169.

16. Changed “will be ignored” to “must be written to zero” for unused Z-pointer
bits under “Performing a Page Write” on page 216.

17. Added note for RSTDISBL Fuse in Table 87 on page 223.

18.Updated drawings in “Packaging Information” on page 14.

Changes from Rev. 1.Added errata for Rev D, E, and F on page 17.
2486H-09/02 to Rev.
2486I-12/02

Changes from Rev. 1.Changed the Endurance on the Flash to 10,000 Write/Erase Cycles.
2486G-09/02 to Rev.
2486H-09/02

Changes from Rev. 1 Updated Table 103, “ADC Characteristics,” on page 248.
2486F-07/02 to Rev.
2486G-09/02

20 ATmega8(L)
2486QS–AVR–10/06
 ATmega8(L)

Changes from Rev. 1 Changes in “Digital Input Enable and Sleep Modes” on page 55.
2486E-06/02 to Rev.
2486F-07/02 2 Addition of OCS2 in “MOSI/OC2 – Port B, Bit 3” on page 59.

3 The following tables has been updated:

Table 51, “CPOL and CPHA Functionality,” on page 132, Table 59, “UCPOL Bit Set-
tings,” on page 158, Table 72, “Analog Comparator Multiplexed Input (1) ,” on
page 195, Table 73, “ADC Conversion Time,” on page 200, Table 75, “Input Chan-
nel Selections,” on page 206, and Table 84, “Explanation of Different Variables
used in Figure 103 and the Mapping to the Z-pointer,” on page 221.

5 Changes in “Reading the Calibration Byte” on page 234.

6 Corrected Errors in Cross References.

Changes from Rev. 1 Updated Some Preliminary Test Limits and Characterization Data
2486D-03/02 to Rev. The following tables have been updated:
2486E-06/02 Table 15, “Reset Characteristics,” on page 38, Table 16, “Internal Voltage Refer-
ence Characteristics,” on page 42, DC Characteristics on page 242, Table , “ADC
Characteristics,” on page 248.

2 Changes in External Clock Frequency

Added the description at the end of “External Clock” on page 32.
Added period changing data in Table 99, “External Clock Drive,” on page 244.

3 Updated TWI Chapter

More details regarding use of the TWI bit rate prescaler and a Table 65, “TWI Bit
Rate Prescaler,” on page 173.

Changes from Rev. 1 Updated Typical Start-up Times.

2486C-03/02 to Rev. The following tables has been updated:
2486D-03/02 Table 5, “Start-up Times for the Crystal Oscillator Clock Selection,” on page 28,
Table 6, “Start-up Times for the Low-frequency Crystal Oscillator Clock Selection,”
on page 28, Table 8, “Start-up Times for the External RC Oscillator Clock Selec-
tion,” on page 29, and Table 12, “Start-up Times for the External Clock Selection,”
on page 32.
2 Added “ATmega8 Typical Characteristics” on page 249.

Changes from Rev. 1 Updated TWI Chapter.

2486B-12/01 to Rev. More details regarding use of the TWI Power-down operation and using the TWI as
2486C-03/02 Master with low TWBRR values are added into the datasheet.
Added the note at the end of the “Bit Rate Generator Unit” on page 170.
Added the description at the end of “Address Match Unit” on page 170.

2 Updated Description of OSCCAL Calibration Byte.

In the datasheet, it was not explained how to take advantage of the calibration bytes
for 2, 4, and 8 MHz Oscillator selections. This is now added in the following
sections:

21
2486QS–AVR–10/06
 Improved description of “Oscillator Calibration Register – OSCCAL” on page 31 and
“Calibration Byte” on page 225.

3 Added Some Preliminary Test Limits and Characterization Data.

Removed some of the TBD’s in the following tables and pages:
Table 3 on page 26, Table 15 on page 38, Table 16 on page 42, Table 17 on page
44, “TA = -40°C to 85°C, VCC = 2.7V to 5.5V (unless otherwise noted)” on page 242,
Table 99 on page 244, and Table 102 on page 246.

4 Updated Programming Figures.

Figure 104 on page 226 and Figure 112 on page 237 are updated to also reflect that
AVCC must be connected during Programming mode.

5 Added a Description on how to Enter Parallel Programming Mode if RESET

Pin is Disabled or if External Oscillators are Selected.
Added a note in section “Enter Programming Mode” on page 228.

22 ATmega8(L)
2486QS–AVR–10/06
 Atmel Corporation Atmel Operations
2325 Orchard Parkway Memory RF/Automotive
San Jose, CA 95131, USA 2325 Orchard Parkway Theresienstrasse 2
Tel: 1(408) 441-0311 San Jose, CA 95131, USA Postfach 3535
Fax: 1(408) 487-2600 Tel: 1(408) 441-0311 74025 Heilbronn, Germany
Fax: 1(408) 436-4314 Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Regional Headquarters Microcontrollers
Europe 2325 Orchard Parkway 1150 East Cheyenne Mtn. Blvd.
Atmel Sarl San Jose, CA 95131, USA Colorado Springs, CO 80906, USA
Route des Arsenaux 41 Tel: 1(408) 441-0311 Tel: 1(719) 576-3300
Case Postale 80 Fax: 1(408) 436-4314 Fax: 1(719) 540-1759
CH-1705 Fribourg
Switzerland La Chantrerie Biometrics/Imaging/Hi-Rel MPU/
Tel: (41) 26-426-5555 BP 70602 High Speed Converters/RF Datacom
Fax: (41) 26-426-5500 44306 Nantes Cedex 3, France Avenue de Rochepleine
Tel: (33) 2-40-18-18-18 BP 123
Asia Fax: (33) 2-40-18-19-60 38521 Saint-Egreve Cedex, France
Room 1219 Tel: (33) 4-76-58-30-00
Chinachem Golden Plaza ASIC/ASSP/Smart Cards Fax: (33) 4-76-58-34-80
77 Mody Road Tsimshatsui Zone Industrielle
East Kowloon 13106 Rousset Cedex, France
Hong Kong Tel: (33) 4-42-53-60-00
Tel: (852) 2721-9778 Fax: (33) 4-42-53-60-01
Fax: (852) 2722-1369
1150 East Cheyenne Mtn. Blvd.
Japan Colorado Springs, CO 80906, USA
9F, Tonetsu Shinkawa Bldg. Tel: 1(719) 576-3300
1-24-8 Shinkawa Fax: 1(719) 540-1759
Chuo-ku, Tokyo 104-0033
Japan Scottish Enterprise Technology Park
Tel: (81) 3-3523-3551 Maxwell Building
Fax: (81) 3-3523-7581 East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743

Literature Requests
www.atmel.com/literature

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.

© 2006 Atmel Corporation. All rights reserved. ATMEL ®, logo and combinations thereof, Everywhere You Are ®, AVR®, AVR Studio ®, and oth-
ers are the registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of
others.

2486QS–AVR–10/06