JHS-180 - Operational Manual For Installer PDF
JHS-180 - Operational Manual For Installer PDF
JHS-180 - Operational Manual For Installer PDF
CHAPTER 3
3-1
1. Field Maintenance Mode
1.1 Startup in Field Maintenance Mode
Caution
When started in the field maintenance mode, this equipment stops transmission.
After completion of operation in the field maintenance mode, make sure to restart in
the normal mode (with the PWR key pressed).
The JHS-180 has the field maintenance mode for initialization at the time of
installation and maintenance. To start the equipment in the field maintenance mode,
operate as the following.
[Operation Method]
When turning on the power, press the [PWR] and [MENU] keys simultaneously and
hold them down until the message, AIS CONTROLLER NOW LOADING ---, appears on
the AIS controller screen.
The actions in the field maintenance mode are as follows.
- No auto transmission with the TDMA.
- The two menu items are added in the main menu: 8. FIELD MAINTENANCE and 9.
INITIALIZE. (See the following figure.)
3-2
1.2 Display List (FIELD MAINTENANCE MODE)
3-3
2. Field Maintenance
Pressing Key 8 in the main menu causes the FIELD MAINTENANCE menu to appear.
2.1 Self-Diagnosis
Pressing Key 1 in the FIELD MAINTENANCE menu causes the SELF TEST menu to
appear. The transponder and controller are diagnosed individually using the SELF
TEST menu.
3-4
Display Screen of Self-Diagnosed Result (All Tests Unsuccessful)
3-5
Self Diagnosis Items of NTE-180 AIS Transponder
Display Description on Self Diagnosis
TEST (Reserved for future use)
TEST1 Control unit
TEST2 GPS receiver
TEST3 Modem
TEST4 Receiver and frequency synthesizer
TEST5 Modem, digital frequency conversion unit, receiver (excluding PA)
TEST6 Modem, digital frequency conversion unit, receiver (including PA)
TEST TX (Reserved for future use)
3-6
2.2 Communication Status
Pressing Key 2 in the FIELD MAINTENANCE menu causes the COMM STATUS menu
to appear. The number of receiving stations and synchronous state can be checked using
the COMM STATUS menu. There are two types of synchronous states, UTC DIRECT
and UTC INDIRECT. The UTC DIRECT state means that the GPS data comes from
own ship’s internal GPS reception. The UTC INDIRECT state means that the GPS data
is received indirectly from another ship or shore station.
3-7
2.3 Reporting Rate
Pressing Key 3 in the FIELD MAINTENANCE menu causes the REPORTING RATE
menu to appear. The reporting rate can be changed temporarily using the REPORTING
RATE menu One of the following rates can be selected: 60, 100, 180, and 300, 600
3-8
2.4 Self Diagnosis Log
Pressing Key 4 in the FIELD MAINTENANCE menu causes the SELF TEST LOG
menu to appear. The latest 20 self-diagnosis results are recorded as self-diagnosis logs
in NCM-722.. The resultant logs can be checked using the SELF TEST LOG menu
3-9
2.5 Range Alarm Log
Pressing Key 5 in the FIELD MAINTENANCE menu causes the RANGE ALARM LOG
menu to appear. A total of 20 records of guard zone and lost target alarms are stored in
the NCM-722 as range alarm logs. These logs can be checked using the RANGE ALARM
LOG menu.
3-10
2.6 Port Log
Pressing Key 6 in the FIELD MAINTENANCE menu causes the PORT LOG menu to
appear. Communication logs in each communication port can be checked using the
PORT LOG menu.
3-11
2.7 Port Option
Pressing Key 7 in the FIELD MAINTENANCE menu causes the PORT OPTION menu
to appear. You can specify a function to output the special command ($PJRCxx) as well
as the VHF radio communication commands (VDM and VDO) using the PORT OPTION
menu.
3-12
2.8 TRX Check
Pressing Key 8 in the FIELD MAINTENANCE menu causes the TRX CHECK menu to
appear.
Pressing Key 1 in the TRX CHECK menu causes the CHANNEL SET menu to appear.
Any channel can be set for reception channels. Input channels on the items "1. CH A"
and "2. CH B" and select "3. SET" to set the channels.
3-13
Pressing Key 2 in the TRX CHECK menu causes the TX POWER CHECK menu to
appear. Using the TX POWER CHECK menu, continuous transmission can be
performed through any channel.
[Procedure]
(1) Select "1. CH", "2. BANDWIDTH", "3. TX TYPE", "4. TX POWER" and enter
corresponding values.
(2) Press the select key TX ON> O continuous transmission starts.
(3) Press the select key TX OFF>O to stop the transmission.
This function is used for transmission power measurement or transmission frequency
measurement.
3-14
Pressing Key 3 in the TRX CHECK menu causes the TX POWER ADJUST menu to
appear. (This function will be supported in the future.)
With the TX POWER ADJUST menu, power can be adjusted while continuous
transmission is performed through any channel. In addition, power setting and multiple
channels can be set while transmission is stopped.
[Procedure]
(1) Select "1. CH", "2. BANDWIDTH", "3. TX TYPE", "4. TX POWER" and enter
corresponding values.
(2) Press the select key TX ON> O. Then continuous transmission starts.
(3) Select 5. INDEX, input power adjustment value (0 - 255), and press the ENT key.
(4) Press the select key TX OFF> O to stop the transmission.
(5) Pressing the select key WRITE> O causes the current power adjustment value to be
written in the current channel.
(6) Selecting 7. COPY CH GROUP x causes the current power adjustment value to be
written in the channel in the channel group.
This function is usable for transmission power adjustment and setting.
3-15
2.9 Software Upgrading
Pressing Key 9 in the FIELD MAINTENANCE menu causes the SOFTWARE VER UP
menu to appear. With the SOFTWARE VER UP menu, the transponder and controller
software can be updated. In either software, the power supply should be turned off and
on after loading the software.
3-16
Display Screen after AIS Controller Software Upgraded
3-17
2.10 AIS Controller Initialization
Pressing Key 0 in the FIELD MAINTENANCE menu causes the STATE INITIALIZE
menu to appear. With the STATE INITIALIZE menu, all controller data can be
initialized (erased).
The data to be initialized and the initialized states are as follows.
(1) Transmission message “TX TRAY”: Space for total of 10 messages becomes blank.
(2) Reception message “RX TRAY”: Space for total of 10 messages becomes blank.
(3) Destination “DESTINATION”: Space for 5 logs becomes blank.
(4) Way-point “WAYPOINT”: Space for 14-point names becomes blank and latitude and
longitude are zeroed.
(5) Range alarm setting “RANGE” and “LOST TARGET”: Set to 0.0 NM.
(6) Consort ship setting “GROUP SHIP”: Space for up to 50-ship names and MMSI
becomes blank
(7) Password “PASSWORD”: Set to 0000
(8) Long range response setting “LONGRANGE RESPONSE”: MANUAL
(9) Contrast “CONTRAST”: Set to 3
(10) Self test logs “SELF TEST LOG”: Space for up to 20 logs becomes blank.
(11) Range alarm logs “RANGE ALARM LOG”: Space for up to 20 logs becomes blank.
(12) Internal GPS initialization “INTERNAL GPS SETTING”: Zeroed
(13) Sensor filter “SENSOR SETTING”: All sentences become available.
(14) Static information “SHIP STATIC DATA SETTING”: Numerals are zeroed and
characters become blank for all items except “SENSOR TYPE”, which is GPS by default.
3-18
Display Screen of STATE INITIALIZE (with OFF)
3-19
3. Initialization
Pressing Key 9 in the Main Menu causes the INITIALIZE menu to appear.
3-20
3.1 Sensor Setting
Pressing Key 1 in the INITIALIZE menu causes the SENSOR SETTING menu to
appear. Using the SENSOR SETTING menu, specify sensor filters (valid commands),
communication rate, presence/absence of parity bit, etc.
3-21
3.2 Internal GPS Setting
Pressing Key 2 in the INITIALIZE menu causes the INT. GPS SETTING menu to
appear.
3-22
3.3 Static Information Setting
Pressing Key 3 in the INITIALIZE menu causes the SHIP STATIC DATA menu to
appear. Use the SHIP STATIC DATA menu to specify own ship’s static information.
3-23
3.4 AIS Transponder Initialization
Pressing Key 4 in the INITIALIZE menu causes the TRANSPONDER INIT menu to
appear.
Transponder data can be initialized (erased) using the TRANSPONDER INIT menu
Data to be initialized in the transponder and the initialized state is as follows.
(1) Static information “SHIP STATIC DATA SETTING”: Numerals set to zero and
characters set to blank.
(2) Regional frequency “CHANNEL MANAGEMENT”: Space for 8 regions becomes
blank
(3) Power on/off log “POWER ON/OFF LOG”: Space for up to 10 logs becomes blank.
(4) Own ship position (GPS initial value or satellite supplementary position): No
position
To complete the initialization, press the select key. After the initialization, turn the
power supply off and on.
3-24
3.5 Antenna Selection
Pressing Key 5 in the INITIALIZE menu causes the ANTENNA SELECTION menu to
appear.
With the ANTENNA SELECTION menu, specify INTERNAL or EXTERNAL for the
VHF antenna. Normally the setting is INTERNAL (appended whip antenna), but select
EXTERNAL if an external antenna is to be used.
3-25
REFERENCES
The regional operating frequencies used for AIS are established in Japan.
Please set the primary frequency on 161.575MHz(ch2079), the secondary frequency
on 161.675MHz(ch2081),transmitting band width of wideband (25kHz separation),
antenna power of 12.5W, transitional zone size in 1NM, and operate in the area
designated by Mercator projection rectangle with two reference points(WGS-84) shown
by the following geographical coordinate address of the northeastern corner and the
geographical coordinate address of the southwestern corner of the rectangle.
2
THE
THEAIS
AISREGIONAL
REGIONALOPERATING
OPERATINGAREAS
AREAS
DATA OF MERCATOR PROJECTION RECTAGLE
AREAS
NORTHEASTERN CORNER SOUTHWESTERN CORNER
1 44°41.0′N 144°56.0′E 43°51.0′N 143°36.0′E
2 43°44.0′N 142°16.0′E 41°08.0′N 139°19.0′E
3 38°58.0′N 142°01.0′E 36°16.0′N 140°35.0′E
4 36°16.0′N 141°20.0′E 34°07.0′N 138°08.0′E
5 35°10.0′N 138°08.0′E 32°46.0′N 135°52.0′E
6 34°47.0′N 135°52.0′E 32°22.0′N 132°47.0′E 11
7 35°10.0′N 132°47.0′E 32°22.0′N 129°39.0′E
8 36°35.0′N 134°50.0′E 35°10.0′N 131°33.0′E
9 37°46.0′N 138°03.0′E 35°27.0′N 134°50.0′E
10 39°14.0′N 140°03.0′E 37°03.0′N 138°03.0′E
11 41°08.0′N 141°23.0′E 39°14.0′N 138°58.0′E
10
(TRANSITIONAL ZONE SIZE:1NM)
3
●Out of the areas, AIS should be use ch2087/2088(161.975/162.025MHz)
●In the areas, AIS should be use ch2079/2081(161.575/161.675MHz)
8
4
7 5
6
Monitoring JHS-180 AIS using Personal Computers
The AUX1 and AUX2 ports for connecting external devices to JHS-180 comply with the RS-
422 specification. To load own ship’s transmission information or reception information for
other ships into a personal computer, convert the information from RS-422 to RS-232C or
connect the device to the personal computer through the PCMCIA card.
1. Connection Method
(1) Use of an RS-422/232C converter
AUX1or AUX2
RS-422/232C Personal
JHS-180 Converter Computer
JHS-180 Handheld
PC
NTE-180 CHASSIS
CDJ-2047 CONTROL UNIT
JHS-180
CBD-1569 POWER SUPPLY UNIT
AIS
NCM-722 CQD-1809 PC I/F UNIT
Controller
CDE-989 LCD UNIT
NCM-722 CHASSIS
J1:H-7JAJD0006
A A
CAG-2180
LNA UNIT
J2
W3:H-7ZCJD0080
P2
RED
RED
BLACK
BLACK
ORANGE
BLUE
YELLOW
GREEN
GRAY
WHITE
B J9 1 4 J7 1 6 J8 J2 B
TXD-
TXD+
RXD-
RXD+
DC+_IN
DC+_IN
DC-_IN
GPS_ANT
VHF_ANT
DC-_IN
GND_ISO
U1:CCA-453JP
GPS UNIT
CDJ-2180
CONTROL UNIT 1 10
+B
W1:H-7ZCJD0098A
VCC
GND
J4 P1
VANT
DGPS
TX_SWR_VF 1 1 TX_POWER_CONT
TX_SWR_VR DGND
INTGPS PPS
INTGPS RXD
INTGPS TXD
CMJ-2180 DGND EXT_ANT
MODEM UNIT PA_TEMP ANT_TX
J6 P6 P5 J5 IC DGND
5 5
+5V 1 1 S_CHG2 +3.3V 1 1 IC_ERROR TX_KEY
+5V S_CHG3 +3.3V DUC_PDCLK VR_ERROR PA_OFF
C DGND PAG DGND DGND DGND DGND
C
S_CHG1 SYSCLK DGND DUC_KEY DGND RX_PLL_CLK
TX_BT_CONT 5 5 DGND 5 5 DSC_RXD RX_PLL_LAT3 10 10 RX_PLL_DATA
RX_BT_CONT1 RX_AF1 DUC_DATA[13] DUC_DATA[12] RX_PLL_LK3 DGND
RX_BT_CONT2 PAG DUC_DATA[11] DUC_DATA[10] RX_LO RX_RSSI3
CMN-2180
RB_RES PAG DUC_DATA[ 9] DUC_DATA[ 8] TX_LO TEST TRX UNIT
BS_RES DUC_DATA[ 7] DUC_DATA[ 6] DGND DGND
DGND 10 10 DGND DUC_DATA[ 5] 10 10 DUC_DATA[ 4] RX_RSSI2 15 15 DSC_AF
FLDSC_TXD RX_AF2 DUC_DATA[ 3] DUC_DATA[ 2] RX_PLL_LAT2 DGND
TX_MODE PAG DUC_DATA[ 1] DUC_DATA[ 0] RX_PLL_LK2
DSC_SCK PAG DGND DGND CNT_OUT DGND
DSCDATA_IN BER PLD_KEY_ RX_TUNE2 RX_AF2
FOUND_CHG 15 15 DGND RX_DATA1 15 15 DGND DGND 20 20 DGND
RB_INT DSC_AF RX_CLK1 TXDATA RX_RSSI1
BIT_CHG PAG DGND TX_CLK RX_PLL_LAT1 DGND
RB PAG RX_DATA2 DGND RX_PLL_LK1 RX_AF1
D DGND RX_CLK2 S_CLK CNT_ON DGND D
TESTCONT 20 20 PAG TEST 20 20 DGND RX_TUNE1 25 25
A B A B A B A B A B A B
12V-
12V+
12V+
12V+
12V-
12V-
12V-
12V+
12V+
12V-
12V+
12V-
TX_IF
12.8MHz
12.8MHz
TX_IF
EXT_ANT
J3 J1 J2 J4 J5 J7 J3 J1
1 6 1 4 1 2
GND
W6:XK6W-2EE1-250
W4:H-7ZCJD0091A
W7:XK6W-2EE1-060
E E
W5:H-7ZCJD0081A
J2
EXT_ANT
出図責任
RED
RED
BLACK
BLACK
YELLOW
GREEN
ORANGE
BLUE
GRAY
承 認 検 認 検 図 担 当 尺 度 名 葉
NTE-180 AIS TRANSPONDER 1
24V+
24V+
24V-
24V-
F : 称 CHASSIS 接続図 番 1 F
GND_ISO
A 3
図 E D 0 0 -
TRANSPONDER Tx-A
TRANSPONDER Tx-B
TRANSPONDER Rx-A
TRANSPONDER Rx-B
番 N T E - 1 8 0
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
記号 改 訂 履 歴
EXT_ANT
Ic_ERR,Vr_ERR Buffer
9V AVR 12V
Vf 38.4MHz 2SC2714 38.4MHz TC7SH14F 2SC2714 2SC2714 PLD:
XCV200-4PQ240I MBM29LV004
B FLASH
B
NJM3404 TCXO MOD NRZ(DSC)
NJM7805 ROM
EXT ANT 12.8MHz DSC 4Mbit
ANT TX TX_POWER_ CONT
5V AVR Buffer
Vr 2SC2714
SCA:HD64570F ADRESS
12.8MHz DEC
NRZI
MOD SCA PORT
GMSK ch_0 CONT
NRZI
Amp SN74LVC541
2SK302 5MXB13-17 2SK2171 45MHz 2SK302 455kHz Limitter Amp 455kHz NJM3404 NJM3404 TLV2541 DSP: TMS320VC5402 SN74ACT573
TA31137FN Limitter Amp TL74LCX16245AFT
FLASH
2SK210 2SK210 Loop Filter ROM
57.645MHz 24.576MHz
RX RSSI2 MODEM UNIT: RX_fs CLK
RF_TUNE2 GENE
CMJ-2180 153.6kHz
D Lo Amp D
2SC3357 2SC2714 MB1511 PLD:7DDJD0008
RX_PLL_LK2 24.576MHz
1kHz CLK
1/N PD 1/R 12.8MHz GENE1
97.925~103.925MHz (SIO)
RESET
3.3V IC
Amp
3.072MHz
2SK302 5MXB13-17 2SK2171 21.4MHz 2SK302 TA31137FN 455kHz Limitter Amp 455kHz Limitter Amp NJM3404
GPS
DGPS
DET LNA_OUT CCA- GPS_DATA
SERI
453JP
PPS
TX_1ST_LOCAL ADRESS DEC 3.072MHz
2SK210 2SK210 Loop Filter GPS_DATA PPS
20.945MHz MAX724 HA16103
Lo Amp
2SC3357 RX RSSI3 SW RS422 REST
12V REG DRIVER
SIO _IC
LM2576
VDD_ISO
2SC2714 MB1511 SW (3.3V)
E RX_PLL_LK3 5V REG UPC29M33 VS0505S 1kHz E
PQ3RD23
1/N PD 1/R 12.8MHz
5V
134.625~140.625MHz 3.3V AVR AVR DC/DC 5V
LNA UNIT:CAG-2180
GPS ANTENNA
DC24V from/to AIS
NJG1103 NJG1103
Controller 出図責任
LNA_OUT
承 認 検 認 検 図 担 当 尺 度 名 NTE-180 AIS TRANSPONDER 葉
1
: BLOCK DIAGRAM
F 称 番 1 F
A 3
図 E Z 0 0 -
2000.12.5
2000.12 .5
番 N T E - 1 8 0
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
RI
A A
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
GND
TxN
TxP
RxP
RxN
VBus
Data-
Data+
Rx LED+
Rx LED-
Not used
Not used
Not used
Not used
Link LED-
Link LED+
FDED-9S(HIROSE)
787780-1(AMP) RJHS-5381(AMPHENOL)
AIS CONTROLLER PC I/F UNIT
HIF2E-14D-2.54RB(HIROSE)
NCM-722 W1 CQD-1809
7ZCAF0070
HIF3BA-10D-2.54R 1 14 W2
(HIROSE) HIF3BA-14D-2.54R 7ZCAF0071
1 10
J201
RI
J101
DCD
TXD
DTR
GND
DSR
RXD
RTS
CTS
GND
TxN
RxN
TxP
RxP
HIF3FC-14PA
VBus
Data+
Data-
Rx LED+
Rx LED-
B W9 -2.54DSA B
LINK LED-
LINK LED+
COM:RS232C
7ZCJD0093 J9 (HIROSE)
HIF3FC-10PA-2.54DSA (HIROSE)
1 CONNECT1
VCC(+5V) W6
J601
VCC(+5V) 7ZCAF0068
J6 J601 PORT J6 J601 PORT 1 2
GND 1 1 SENSOR5_RX-A 20 2 SENSOR5_RX-B
GND 2 3 AUX1_TX-A 21 4 AUX1_TX-B 1 1 J6
W12 GND CONTROL UNIT 3 5 AUX1_RX-A 22 6AUX1_RX-B 20
J12 7ZCJD0094 4 7 NSK_TX-A 23 8 NSK_TX-B
GND 5 9 NSK_RX-A 24 10 NSK_RX-B
+ + VDD(+3.3V) CDJ-2047 6 11 MAINTE_TX-A 25 12 MAINTE_TX-B
AWG16 VDD(+3.3V) 7 13 GND-ISO
8 15 ALARM_1C 26 14 ALARM_1A
AWG20(3A)
- - -23V(LCD)
9 17 ALARM_1B 27 16 ALARM_1C
-23V(LCD)
10 19 SENSOR4_RX-A 28 18 SENSOR4_RX-B
C VDD-ISO(422,+3.3V) 11 21 NC 29 20 NC C
VDD-ISO(422,+3.3V) 12 23 SENSOR3_RX-A 30 22 SENSOR3_RX-B
DC24V GND-ISO(422) 13 25 SENSOR2_RX-A 31 24 SENSOR2_RX-B CONNECT1
AWG28-1.27(1A)
DF1B-20DP-2.5DSA(HIROSE)
14 27 SENSOR1_RX-A 32 26 SENSOR1_RX-B
CBD-1569
GND-ISO(422)
VHR-2N (JST)
B2P-VH(JST)
15 29 GND 33 28 GND
Power ON(DIM) 16 31 TRANSPONDER_RX-A 34 30 TRANSPONDER_RX-B
FDCD-37P(HIROSE)
HIF3BA-40D-2.54R (HIROSE)
17 33 TRANSPONDER_TX-A 35 32 TRANSPONDER_TX-B
DF1B-20DS-2.5RC
Power OFF(CONT)
Power COM
} 18 35 GND-ISO 36 34 GND-ISO
LTWB-3MS-C(TYUOUMUSEN)
39 NC 38 NC
CONT+ 40 NC
GND COM
HIF3FC-40PA-2.54DSA (HIROSE)
20
37
19
39 40
D 1 CONNECT2 D
1 J8 2 1 W7
VFLSO/FRZ 7ZCAF0069
(POWER ON/OFF) GND J7 J701 PORT J7 J701 PORT
J701
RTN3
1
13 J7
GND 1 25 RESERVED 14 24 RESERVED 25
RTN2 HRESET 2 23 RESERVED 15 22 RESERVED
RTN0 VDD 3 21 AUX2_TX-A 16 20 AUX2_TX-B
RTN4 DSDO 4 19 AUX2_RX-A 17 18 AUX2_RX-B
P100(BDM)
DSDI 5 17 LONGRANGE_TX-A 18 16 LONGRANGE_TX-B
RTN5 VFLS1/FRZ 6 15 LONGRANGE_RX-A 19 14 LONGRANGE_RX-B
PWR DSDK 7 13 DIFF_TX-A 20 12 DIFF_TX-B CONNECT2
OFF SRESET 8 11 DIFF_RX-A 21 10 DIFF_RX-B
RTN1 9 9 NMAE2000_TX-A 22 8 NMAE2000_TX-B
AWG28-1.27(1A)
FPC Cable
10 UFP-10A-03#4 10 7 NMAE2000_RX-A 23 6 NMAE2000_RX-B
S1:KEYPAD
SCAN3 (YAMAICHI)
68101-013(HAKUTOU)
11 5 GND-ISO
COM 12 3 ALARM_2C 24 4 ALARM_2B
FDBD-25P(HIROSE)
E E
HIF3FC-26PA-2.54DSA (HIROSE)
SCAN1 26 NC 14
742J2.54-10 1
SCAN0 742J2.54-10 26 25
13 J3 J4 (T&B)
LED-K
LED-A(+5V)
10 (T&B) 1 10 1
J5
2 1
W3 W4
改 W5
7ZCJD0092 19 1 20 2 出図責任
D7
D5
D3
D1
A0
RD
NC
D6
D4
D2
D0
CS
WR
VEE
VDD
GND
GND
承 認 検 認 検 図 担 当 尺 度
HALT
AWG28(1A)
訂 CDE-989 LED-A(+5V)
F LCD UNIT LED-K U1:DMF5001NY-LY-AIE(OPTREX) 称 総合接続図 番 1F
承 A3 図 E D 0 0 -
認 番 N C M -7 2 2 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
+5V ①
+3.3V EEPROM PT-422Trcv
64/128Kbits UART
DS1608C-106 3.3V(Isolation)
MEB-12C-5
SCL
SDA
A (Coilcraft) A
ブザー (シチズン電子) 232C切替
24LC64A/P
(メンテナス用) (Microchip) SIO(I2C)
IO x1 PT 422 Trcv
Txd 422Trcv ① TRANSPONDER
COM: (1ch)
232CTrcv Rxd CPU POWER PC UART1 CS2-0 x2 (38.4kbps)
RS-232C
(1ch) CS SIO(SCC3) XPC850DEZT50B(モトローラ) PT 422 Rcv
(230.4kbps-50bps) RS 232C切替 MBM29LV160B-90PFTN(富士通) SENSOR 1
DATA x8
(1ch) (38.4kbps or 4800bps)
(DTR,DSR,CD,RI) x1
IO x4 DATA-BUS DATA x32 ADD x8 UART
(32) DATA BUS PT
ADD x20 Flash ROM UART1 INTx1 (8ch) 422 Rcv SENSOR 2
MAX3223ECAP(マキシム) (1ch)
B RD&WR(2) 16Mbits×2 (38.4kbps or 4800bps) B
x1
ADD-BUS RD&WR(2)
ADD BUS CS0 PT 422 Rcv
(26) HRESET SENSOR 3
SIO (USB) ADD:20 (1ch)
USB USB ×2 x1 (38.4kbps or 4800bps)
DATA:16
Trcv MEMORY CONTROL BRGO2
(12Mbps Dev1.1) PT SENSOR 4
LCD (CS4) F-ROM (CS0) (3.6927MHz)
CS(8)
Pannel x2 (CS5,CS6) SDRAM (CS1) x1
(4800bps for JRC GPS)
USB1T11AMTC(FAIRCHILD) Cont.& Light (CS7) UART (CS2,CS3)
PT SENSOR 5
RD/WR RD/WR SPARE (4800bps for JRC GPS)
X'tal x1
RAS (2ch)
20MHz DRAM K4S643232C-TC80(サムソン) PT 422 Trcv
Eternet CAS AUX1
Ethernet トランス DATA x32 (1ch)
C Trcv SDRAM x2 (38.4kbps) C
(10Mbps) SIO (SCC2) IRQ MAP IRQ0(NMI)
・UART x2
ADD x11
・MODEM(DSP)x3
64Mbits PT 422 Trcv NSK
23Z467SM IRQ(7) RD/WR
・ISDN x1 UART x2 (1ch)
(Pulse_Engineering) LXT905LC(LEVEL-ONE) ・SimCard x1 (9600bps)
CS1 ADD:11 x2
BMD
I2C (1) EEPROM (1ch)
RD&WR(2) x2
(38.4kbps)
VFLS1/FRZ CS2-0
232C制御x4 CS2 CS2-1 PT
DSCK BUZZ x1 CSデコーダ HRESET 422Trcv DIFFERENTIAL
(DTR,DSR,CD,RI) CS2-2
デバッグ用コネクタ
IO (13) (1ch)
SRESET RELAY x2 ADD9-11 CS2-3
232C切替 x2
CS2-4
LED x2
UFP-10A-03#4(山一電機) DMA PT 422Trcv NMEA2000
PO RESET
(1ch)
X'tal リセット
(38.4kbps)
32.768KHz HRESET SPARE
SRESET S-80130-BNMC (2ch)
MC-306-32.768KHZ
(セイコーエプソン) (セイコー電子)
E E
UART LSI(6)
IO ×2 リレー
UART LSI(2)
CS2-2
DATA x8
リレー接点出力 x2
UART LSI(4)
(2回路) GND(Isolation)
Contrast x5 Light x2
LATCH DTD123YK(ローム)
ADD x1
CS4
+5V(VDD)
DATA x8
HRESET
G6K-2F-Y DC3V(オムロン) UART:XR16L758(EXAR)x2
RD&WR(2)
PT:PC900V (SHARP) x21
5V
5V
5V
422ドライバ:MAX3488ECSA(マキシム)x11
RTN0-5
改
SCAN0-3
PWR,OFF
LCD電源 出図責任
パネル制御 液晶制御 (VEE) 液晶コントラスト LED パネル 承 認 検 認 検 図 担 当 尺 度 名 CONTROL UNIT CDJ-2047 葉 1
訂 (キー入力) (画面表示) (電圧制御) バックライト制御 バックライト制御
F 称 機能ブロック 番 1F
電圧制御 電流制限
承 A3
ランプ 図
LED
認 キーパッド LCD DMF5001NY-LY(オプトレクス) T4.2AX5V115mAC-8/AF4220G30 番
4個(アロー電子)
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
C C
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CDJ-2047 CONTROL UNIT 1
F 称 組立要領図(部品面) 番 2F
承 A3 図 E F 0 0 -
認 番 C D J - 2 0 4 7 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
C C
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CBD-1569 POWER SUPPLY 1
F 称 組立要領図(部品面) 番 2F
承 A3 図 E F 0 0 -
認 番 C B D - 1 5 6 9 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
W2
C C
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CDQ-1809 PC I/F UNIT 1
F 称 組立要領図 番 1 F
承 A3 図 E F 0 0 -
認 番 C Q D - 1 8 0 9 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
LCDモジュール U1 DMF5001NY-LY-AIE
C C
W5
黒
D 赤 1 D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CDE-989 LCD UNIT 1
F 称 組立要領図 番 1 F
承 A3 図 E F 0 0 -
認 番 C D E - 9 8 9 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
CONNECTION BOX NQE-3111
A PS1 VTD24SC24 A
0V out
DCin +V
+V out
+V out
0V out
FG
DCin 0V
DC24V OUT P102 POWER
(OPTION) 7ZCJD0097 P101
7ZCJD0096
1 3 7 1
F14 J103 1 J102 J101
1A + - E SW+
+ DC OUT+ SW-
- DC OUT-
B F11 6.3A 1 S1 B
E +
DC IN+
-
DC24V OUT
DC IN-
(CONTROLLER)
TB12 5A FILTER UNIT CBL-1221 DC24V IN
F13 F12 E
+ - E 6.3A
H-7PCJD0090A 3 TB11
1 3 J201
P201
P21 7ZCJDB001
1 3
J21
19 37 TERMINAL UNIT CQD-1820 H-7PCAF0067A
C K1 H-7JTAF0010 H-7JTAF0011 C
H-7JTAF0009
(Female)
pin Terminal pin NAME pin Terminal pin NAME pin Terminal pin NAME
POWER ON+ 24V+ 1 SENSOR5_Rx-A 1 AUX2_Tx-A 1 1 J21 K1 24V+ 1 J18 1 SENSOR5_Rx-A 1 J17 3 AUX2_Tx-A
+DC24V 24V+ SENSOR5_Rx-B AUX2_Tx-B 2 J21 K1 24V+ 2 J18 20 SENSOR5_Rx-B 2 J17 16 AUX2_Tx-B
24V+ GND-ISO GND-ISO 3 J21 K1 24V+ 3 GND-ISO 3 GND-ISO
4 AUX2_Rx-A 4 J21 K1 24V+ 4 GND 4 J17 4 AUX2_Rx-A
SENSOR5
24V+ GND-SHIELD
AUX2
AUX2_Rx-B 5 J21 2 24V- 5 J18 2 AUX1_Tx-A 5 J17 17 AUX2_Rx-B
24V- AUX1_Tx-A 6 J21 2 24V- 6 J18 21 AUX1_Tx-B 6 GND-ISO
24V- AUX1_Tx-B GND-ISO 7 J21 2 24V- 7 GND-ISO 7 GND
24V- GND-SHIELD 7 8 J21 2 24V- 8 J18 3 AUX1_Rx-A 8 J17 5 LONGRANGE_Tx-A
GND-ISO
24V- 9 J18 17 TRANSPONDER_Tx-A 9 J18 22 AUX1_Rx-B 9 J17 18 LONGRANGE_Tx-B
CONNECT1
AUX1_Rx-A LONGRANGE_Tx-A
AUX1
TRANSPONDER_Tx-A 10 J18 35 TRANSPONDER_Tx-B 10 GND-ISO 10 GND-ISO
AUX1_Rx-B LONGRANGE_Tx-B 11 J18 16 TRANSPONDER_Rx-A 11 GND 11 J17 6 LONGRANGE_Rx-A
TRANSPONDER
TRANSPONDER_Tx-B GND-ISO GND-ISO 12 J18 34 TRANSPONDER_Rx-B 12 J18 4 NSK_Tx-A 12 J17 19 LONGRANGE_Rx-B
TRANSPONDER_Rx-A GND-SHIELD 11 LONGRANGE_Rx-A 13 GND 13 J18 23 NSK_Tx-B 13 GND-ISO
TRANSPONDER_Rx-B LONGRANGE_Rx-B 14 GND 14 GND-ISO 14 GND
J18 NSK_TXD-A 15 J18 14 SENSOR1_Rx-A 15 J18 5 NSK_Rx-A 15 J17 7 DIFF_Tx-A
LONGRANGE
GND GND-ISO TB1 TB2 TB3
GND 14
NSK_TXD-B 16 J18 32 SENSOR1_Rx-B 16 J18 24 NSK_Rx-B 16 J17 20 DIFF_Tx-B
GND-SHIELD 14
GND-ISO 17 GND-ISO 17 GND-ISO 17 GND-ISO
D 20 D
RDCD-37S-LNA(4-40)(05) (HIROSE)
SENSOR1_Rx-A NSK_RXD-A DIFF_Tx-A 18 GND 18 GND 18 J17 8 DIFF_Rx-A
NSK
1
SENSOR1_Rx-B NSK_RXD-B DIFF_Tx-B 19 J18 13 SENSOR2_Rx-A 19 J18 6 MAINTE_Tx-A 19 J17 21 DIFF_Rx-B
(Sheild) GND-ISO 20 J18 31 SENSOR2_Rx-B 20 J18 25 MAINTE_Tx-B 20 GND-ISO
GND-ISO GND-ISO 21 GND-ISO 21 GND-ISO 21 GND
GND-SHIELD 18 18
DIFF
GND-SHIELD DIFF_Rx-A 22 GND 22 GND 22 J17 9 NMEA2000_Tx-A
SENSOR2_Rx-A MAINTE_Tx-A DIFF_Rx-B 23 J18 12 SENSOR3_Rx-A 23 J18 26 ALARM1A 23 J17 22 NMEA2000_Tx-B
13 25 24 J18 30 SENSOR3_Rx-B 24 J18 8,27 ALARM1C 24 GND
SENSOR2_Rx-B MAINTE_Tx-B GND-ISO
GND-SHIELD 21 25 GND-ISO 25 J18 9 ALARM1B 25 J17 10 NMEA2000_Rx-A
GND-ISO GND-ISO
(Female)
26 GND 26 J17 13 ALARM2A 26 J17 23 NMEA2000_Rx-B
MAINTE
GND-SHIELD 22 22
GND-SHIELD NMEA2000_Tx-A 27 J18 10 SENSOR4_Rx-A 27 J17 25,12 ALARM2C 27 NC
SENSOR3_Rx-A NMEA2000_Tx-B 28 J18 28 SENSOR4_Rx-B 28 J17 24 ALARM2B 28 NC
ALARM_1A 29 GND-ISO 29 NC 29 NC
SENSOR3_Rx-B ALARM_1C GND
30 GND 30 NC 30 NC
GND-ISO ALARM_1B 25
NMEA2000_Rx-A
NMEA2000
26 NMEA2000_Rx-B 26
GND-SHIELD ALARM_2A NC
CONNECT2
SENSOR4_Rx-A ALARM_2C
SENSOR4_Rx-B ALARM_2B 28
NC
GND-ISO NC
NC 30
ALARM2 ALARM1
30 NC
RDBD-25S-LNA(4-40)(05)(HIROSE)
1
TB1 TB2 TB3
(Sheild)
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂
CONNECTION BOX NQE-3111 1
F 称 総合接続図 番 1 F
承 A3 E D 0 0 −
図
認 番 N Q E − 3 1 1 1 − 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
P21
A A
赤
1
COM
黒
P101 S1
B B
J21
J201 (RED) OUT
J102 +24V
1
OUT
+0V
C FG C
7 IN 0V
J101
24V
P102
PS1
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 NQE-3111 シャーシ部 1
F 称 組立要領図 番 1 F
承 A3 図 E F 0 0 -
認 番 N Q E - 3 1 1 1 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
C C
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CDQ-1820 TERMINAL UNIT 1
F 称 組立要領図 番 1 F
承 A3 図 E F 0 0 -
認 番 C Q D - 1 8 2 0 - 0 1
第 3 角法 単位 mm 2 3 6 7 8
1 2 3 4 5 6 7 8
A A
B B
C C
D D
E E
改
出図責任
承 認 検 認 検 図 担 当 尺 度 名 葉
訂 CBL-1221 FILTER UNIT 1
F 称 組立要領図 番 1 F
承 A3 図 E F 0 0 -
認 番 C B L - 1 2 2 1 - 0 1
第 3 角法 単位 mm 2 3 6 7 8