ACS750xCA-50

Fully Integrated, Hall Effect-Based Linear Current Sensor IC

with High Voltage Isolation and a Low-Resistance Current Conductor

Limited Availability Product

This device is in production, but is limited to existing customers.
Contact factory for additional information.

Date of status change: November 2, 2009

Recommended Substitutions:

For existing customer transition, and for new customers or new appli-
cations, refer to the ACS756.

NOTE: For detailed information on purchasing options, contact your

local Allegro field applications engineer or sales representative.

Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan
for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The
information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no respon-
sibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
 ACS750xCA-50
Fully Integrated, Hall Effect-Based Linear Current Sensor IC
with High Voltage Isolation and a Low-Resistance Current Conductor

Features and Benefits Description

▪ Monolithic Hall IC for high reliability The Allegro ACS75x family of current sensor ICs provides
▪ Single +5 V supply economical and precise solutions for current sensing in
▪ 3 kVRMS isolation voltage between terminals 4/5 and industrial, automotive, commercial, and communications
pins 1/2/3 for up to 1 minute systems. The device package allows for easy implementation by
▪ 13 kHz bandwidth the customer. Typical applications include motor control, load
▪ Automotive temperature range detection and management, power supplies, and overcurrent
▪ End-of-line factory-trimmed for gain and offset fault protection.
▪ Ultra-low power loss: 130 μΩ internal conductor
The device consists of a precision, low-offset linear Hall
resistance
circuit with a copper conduction path located near the die.
▪ Ratiometric output from supply voltage
Applied current flowing through this copper conduction path
▪ Extremely stable output offset voltage
generates a magnetic field which the Hall IC converts into a
▪ Small package size, with easy mounting capability
proportional voltage. Device accuracy is optimized through the
▪ Output proportional to AC and DC currents
close proximity of the magnetic signal to the Hall transducer.
A precise, proportional voltage is provided by the low-offset,
chopper-stabilized BiCMOS Hall IC, which is programmed
for accuracy at the factory.
Package: 5 pin package (leadform PFF)
The output of the device has a positive slope (>VCC / 2) when an
increasing current flows through the primary copper conduction
path (from terminal 4 to terminal 5), which is the path used for
current sampling. The internal resistance of this conductive path
is typically 130 μΩ, providing low power loss. The thickness
of the copper conductor allows survival of the device at up to

Continued on the next page…

Typical Application

+5 V
1
4 VCC
IP+ CBYP
ACS750 0.1 µF
2
IP GND
CF
5
IP– 3
VIOUT VOUT
RF

Application 1. The ACS750 outputs an analog signal, VOUT .

that varies linearly with the uni- or bi-directional AC or DC
primary sampled current, IP , within the range specified. CF
is recommended for noise management, with values that
depend on the application.

ACS75050-DS Rev. 13
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Description (continued)
5× overcurrent conditions. The terminals of the conductive path are The device is fully calibrated prior to shipment from the factory.
electrically isolated from the signal leads (pins 1 through 3). This The ACS75x family is lead (Pb) free. All pins are coated with
allows the ACS75x family of sensor ICs to be used in applications
requiring electrical isolation without the use of opto-isolators or 100% matte tin, and there is no lead inside the package. The
other costly isolation techniques. heavy gauge leadframe is made of oxygen-free copper.

Selection Guide
Primary Sampled Sensitivity
TOP
Part Number Current, IP Sens (Typ.) Packing1
(°C)
(A) (mV/A)
ACS750LCA-0502 –40 to 150 ±50 40 170 pieces per bulk bag
1Contact Allegro for additional packing options.
2Variant is in production, but is limited to existing customers. Contact factory for additional information. Status date change November 13, 2009.

Absolute Maximum Ratings

Characteristic Symbol Notes Rating Units
Supply Voltage VCC 16 V
Reverse Supply Voltage VRCC –16 V
Output Voltage VIOUT 16 V
Reverse Output Voltage VRIOUT –0.1 V
Maximum Basic Isolation Voltage VISO 353 VAC, 500 VDC, or Vpk V
Maximum Rated Input Current IIN 100 A
Output Current Source IOUT(Source) 3 mA
Output Current Sink IOUT(Sink) 10 mA
Range L –40 to 150 ºC
Nominal Operating Ambient Temperature TA
Range S –20 to 85 ºC
Maximum Junction TJ(max) 165 ºC
Storage Temperature Tstg –65 to 170 ºC

TÜV America
Fire and Electric Shock
Certificate Number:
EN60950-1:2001
U8V 04 11 54214 001

Allegro MicroSystems, Inc. 2

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Functional Block Diagram

+5 V

IP+ VCC

Voltage
Regulator

To all subcircuits
Dynamic Offset
Cancellation

VIOUT
Filter

Amp Out 0.1 μF

Temperature
Gain Offset
Coefficient

Trim Control

IP– GND

Pin-out Diagram

IP+ 4
3 VIOUT
2 GND
1 VCC
IP– 5

Terminal List Table

Number Name Description
1 VCC Device power supply pin
2 GND Signal ground pin
3 VIOUT Analog output signal pin
4 IP+ Terminal for current being sampled
5 IP– Terminal for current being sampled

Allegro MicroSystems, Inc. 3

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

-050 ELECTRICAL CHARACTERISTICS, over temperature range unless otherwise indicated

Characteristic Symbol Test Conditions Min. Typ. Max. Units
Primary Sampled Current IP –50 – 50 A
Supply Voltage VCC 4.5 5.0 5.5 V
Supply Current ICC VCC = 5.0 V, output open – 7 10 mA
Output Resistance ROUT IOUT = 1.2 mA – 1 2 Ω
Output Capacitance Load CLOAD VOUT to GND – – 10 nF
Output Resistive Load RLOAD VOUT to GND 4.7 – – kΩ
Primary Conductor Resistance RPRIMARY IP = ±100A, TA = 25°C – 130 – μΩ
Isolation Voltage VISO Pins 1-3 and 4-5, 60 Hz, 1 minute 3.0 – – kV
PERFORMANCE CHARACTERISTICS, -20°C to +85°C, VCC = 5 V unless otherwise specified
Propagation time tPROP IP = ±50 A, TA = +25°C – 4 – μs
Response time tRESPONSE IP = ±50 A, TA = +25°C – 27 – μs
Rise time tr IP = ±50 A, TA = +25°C – 26 – μs
Frequency Bandwidth f –3 dB, TA = 25°C – 13 – kHz
Over full range of IP , TA = 25°C 39 40 42 mV/A
Sensitivity Sens
Over full range of IP 36 – 44 mV/A
Peak-to-peak, TA = 25°C
Noise VNOISE – 14 – mV
External filter BW = 24 kHz
Linearity ELIN Over full range of IP – – ±5 %
Symmetry ESYM Over full range of IP 99 102 105 %
Zero Current Output Voltage VOUT(Q) I = 0 A, TA = 25°C – VCC / 2 – V
Electrical Offset Voltage I = 0 A, TA = 25°C –60 – 60 mV
VOE
(Magnetic error not included) I=0A –75 – 75 mV
Magnetic Offset Error IERROM I = 0 A, after excursion of 100 A – ±0.3 ±0.8 A
Total Output Error Over full range of IP , TA = 25°C – ±2 – %
ETOT
(Including all offsets) Over full range of IP – – ±13 %
PERFORMANCE CHARACTERISTICS, -40°C to +150°C, VCC = 5 V unless otherwise specified
Propagation time tPROP IP = ±50 A – 4 – μs
Response time tRESPONSE IP = ±50 A – 27 – μs
Rise time tr IP = ±50 A – 26 – μs
Frequency Bandwidth f –3 dB, TA = 25°C – 13 – kHz
Over full range of IP , TA = 25°C 39 40 42 mV/A
Sensitivity Sens
Over full range of IP , TA = 25°C 33 – 46 mV/A
Peak-to-peak; TA = +25°C
Noise VNOISE – 14 – mV
External filter BW = 40 kHz
Linearity ELIN Over full range of IP – – ±5 %
Symmetry ESYM Over full range of IP 99 102 105 %
Zero Current Output Voltage VOUT(Q) I = 0 A, TA = 25°C – VCC / 2 – V
Electrical Offset Voltage I = 0 A, TA = 25°C –60 – 60 mV
VOE
(Magnetic error not included) I=0A –90 – 90 mV
Magnetic Offset Error IERROM I = 0 A, after excursion of 100 A – 0.3 ±0.8 A
Total Output Error Over full range of IP , TA = 25°C – ±2 – %
ETOT
(Including all offsets) Over full range of IP – – ±15 %

Allegro MicroSystems, Inc. 4

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Definitions of Accuracy Characteristics

Sensitivity (Sens). The change in device output in response to a Quiescent output voltage (VIOUT(Q)). The output of the device
1 A change through the primary conductor. The sensitivity is the when the primary current is zero. For a unipolar supply voltage,
product of the magnetic circuit sensitivity (G / A) and the linear it nominally remains at VCC ⁄ 2. Thus, VCC = 5 V translates into
IC amplifier gain (mV/G). The linear IC amplifier gain is pro-
VIOUT(Q) = 2.5 V. Variation in VOUT(Q) can be attributed to the res-
grammed at the factory to optimize the sensitivity (mV/A) for the
olution of the Allegro linear IC quiescent voltage trim, magnetic
full-scale current of the device.
hysteresis, and thermal drift.
Noise (VNOISE). The product of the linear IC amplifier gain
(mV/G) and the noise floor for the Allegro Hall effect linear IC Electrical offset voltage (VOE). The deviation of the device out-
(≈1 G). The noise floor is derived from the thermal and shot put from its ideal quiescent value of VCC ⁄ 2 due to nonmagnetic
noise observed in Hall elements. Dividing the noise (mV) by the causes.
sensitivity (mV/A) provides the smallest current that the device is
able to resolve. Magnetic offset error (IERROM). The magnetic offset is due to
the residual magnetism (remnant field) of the core material. The
Linearity (ELIN). The degree to which the voltage output from
the IC varies in direct proportion to the primary current through magnetic offset error is highest when the magnetic circuit has
its full-scale amplitude. Nonlinearity in the output can be attrib- been saturated, usually when the device has been subjected to a
uted to the saturation of the flux concentrator approaching the full-scale or high-current overload condition. The magnetic offset
full-scale current. The following equation is used to derive the is largely dependent on the material used as a flux concentrator.
linearity: The larger magnetic offsets are observed at the lower operating

100 1–{ [ Δ gain × % sat ( VIOUT_full-scale amperes – VIOUT(Q) )

2 (VIOUT_half-scale amperes – VIOUT(Q) ) [{ temperatures.
Accuracy (ETOT). The accuracy represents the maximum devia-
where tion of the actual output from its ideal value. This is also known
∆ gain = the gain variation as a function of temperature as the total output error. The accuracy is illustrated graphically in
changes from 25ºC, the output voltage versus current chart on the following page.
% sat = the percentage of saturation of the flux concentra-
Accuracy is divided into four areas:
tor, which becomes significant as the current being sampled
approaches full-scale ±IP , and  0 A at 25°C. Accuracy at the zero current flow at 25°C, with-
VIOUT_full-scale amperes = the output voltage (V) when the out the effects of temperature.
sampled current approximates full-scale ±IP .
 0 A over Δ temperature. Accuracy at the zero current flow
Symmetry (ESYM). The degree to which the absolute voltage including temperature effects.
output from the IC varies in proportion to either a positive or
negative full-scale primary current. The following equation is  Full-scale current at 25°C. Accuracy at the the full-scale current
used to derive symmetry: at 25°C, without the effects of temperature.
VIOUT_+ full-scale amperes – VIOUT(Q)  Full-scale current over Δ temperature. Accuracy at the full-
100
VIOUT(Q) – VIOUT_–full-scale amperes
  scale current flow including temperature effects.

Allegro MicroSystems, Inc. 5

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Output Voltage versus Sampled Current

Accuracy at 0 A and at Full-Scale Current
Increasing VIOUT(V)
Accuracy
Over $Temp erature

Accuracy
25°C Only

Average
VIOUT

Accuracy
Over $Temp erature

Accuracy
25°C Only
IP(min)

–IP (A) +IP (A)

Full Scale
IP(max)

0A

Accuracy
25°C Only

Accuracy
Over $Temp erature

Decreasing VIOUT(V)

Definitions of Dynamic Response Characteristics

Propagation delay (tPROP). The time required for the device I (%) Primary Current

output to reflect a change in the primary current signal. Propaga- 90

tion delay is attributed to inductive loading within the linear IC

package, as well as in the inductive loop formed by the primary Transducer Output
conductor geometry. Propagation delay can be considered as a 0
fixed time offset and may be compensated. Propagation Time, tPROP
t

I (%) Primary Current

Response time (tRESPONSE). The time interval between a) when 90

the primary current signal reaches 90% of its final value, and b)
when the device reaches 90% of its output corresponding to the
Transducer Output
applied current.
0
t
Response Time, tRESPONSE

Rise time (tr). The time interval between a) when the device I (%) Primary Current

reaches 10% of its full scale value, and b) when it reaches 90% 90
of its full scale value. The rise time to a step response is used to
derive the bandwidth of the device, in which ƒ(–3 dB) = 0.35 / tr.
Transducer Output
Both tr and tRESPONSE are detrimentally affected by eddy current 10

losses observed in the conductive IC ground plane. 0

t
Rise Time, tr

Allegro MicroSystems, Inc. 6

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Step Response
50 A IP Excitation Signal

Output (mV)

Excitation
Signal

Allegro MicroSystems, Inc. 7

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
 Fully Integrated, Hall Effect-Based Linear Current Sensor IC
ACS750xCA-50
with High Voltage Isolation and a Low-Resistance Current Conductor

Package CA, 5-pin package, leadform PFF

0.5 .020
14.00 R1 .039
1.50
3.00 4.00 R3 .118

5 4
1º
A
2.75
…0.5 .020
R2 .079 B 4 .157
17.50

13.00 3 .118

21.4 .843

4.40
3.18 …0.8 .031

2.90 …1.5 .059

5º
1 2 3
1.91 .075
0.381
10.00

All dimensions nominal, not for tooling use

7.00 Dimensions in millimeters
Exact configuration at supplier discretion within limits shown
A Dambar removal intrusion
3.50 B Perimeter through-holes recommended

0.50
1.90

Creepage distance, current terminals to signal pins: 7.25 mm

Clearance distance, current terminals to signal pins: 7.25 mm
Package mass: 4.63 g typical
Package Branding
Two alternative patterns are used

ACS Allegro Current Sensor ACS Allegro Current Sensor

750 Device family number 750 Device family number
R Operating ambient temperature range code ACS750 R Operating ambient temperature range code
ACS750
CA Package type designator RCAPPP CA Package type designator
RCAPPP
PPP Primary Sampled Current L...L PPP Primary Sampled Current
YYWWA
YY Date code: Calendar year (last two digits) YYWW L...L Lot code
WW Date code: Calendar week YY Date code: Calendar year (last two digits)
A Date code: Shift code WW Date code: Calendar week
Copyright ©2004-2009, Allegro MicroSystems, Inc.
The products described herein are manufactured under one or more of the following U.S. patents: 5,619,137; 5,621,319; 6,781,359; 7,075,287;
7,166,807; 7,265,531; 7,425,821; or other patents pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to per-
mit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the
information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com

Allegro MicroSystems, Inc. 8

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com