Power Electronics 15EC73

Module 2 THYRISTORS

Structure

2.0 Introduction
2.1 Objectives
2.2 Silicon Controlled Rectifier
2.3 Thyristor Gate Characteristics
2.4 Quantitative Analysis
2.5 Switching Characteristics
2.6 Gate Trigger Methods
2.7 Assignment Questions
2.8 Outcomes
2.9 Further Readings

2.0 Introduction
A thyristor is the most important type of power semiconductor devices. They are extensively
used in power electronic circuits. They are operated as bi-stable switches from non-conducting to
conducting state.
A thyristor is a four layer, semiconductor of p-n-p-n structure with three p-n junctions. It has
three terminals, the anode, cathode and the gate.
The word thyristor is coined from thyratron and transistor. It was invented in the year 1957 at
Bell Labs. The Different types of Thyristors are
 Silicon Controlled Rectifier (SCR).

 TRIAC

 DIAC

 Gate Turn Off Thyristor

3.1Objectives:

 Study the physical principles of Thyristors, their structural details and

switching characteristics.
 Study about Brief description of gate triggering circuits.

DEPT OF ECE, ATMECE Page 1

Power Electronics 15EC73

2.2 Silicon Controlled Rectifier (SCR)

The SCR is a four layer three terminal device with junctions as shown. The construction of SCR
shows that the gate terminal is kept nearer the cathode. The approximate thickness of each layer
and doping densities are as indicated in the figure. In terms of their lateral dimensions Thyristors
are the largest semiconductor devices made. A complete silicon wafer as large as ten centimeter
in diameter may be used to make a single high power thyristor.

Qualitative Analysis
When the anode is made positive with respect the cathode junctions 1 3 J & J are
forward biased and junction 2 J is reverse biased. With anode to cathode voltage AK V being
small, only leakage current flows through the device. The SCR is then said to be in the
forward blocking state. If AK V is further increased to a large value, the reverse biased junction

DEPT OF ECE, ATMECE Page 2

Power Electronics 15EC73

2 J will breakdown due to avalanche effect resulting in a large current through the device.
The voltage at which this phenomenon occurs is called the forward breakdown voltage BO V .
Since the other junctions 1 3 J & J are already forward biased, there will be free movement of
carriers across all three junctions resulting in a large forward anode current. Once the SCR is
switched on, the voltage drop across it is very small, typically 1 to 1.5V. The anode current is
limited only by the external impedance present in the circuit.

Although an SCR can be turned on by increasing the forward voltage beyond BO V , in practice,
the forward voltage is maintained well below BO V and the SCR is turned on by applying a
positive voltage between gate and cathode.

With the application of positive gate voltage, the leakage current through the junction 2 J is
increased. This is because the resulting gate current consists mainly of electron flow from
cathode to gate. Since the bottom end layer is heavily doped as compared to the p-layer, due to
the applied voltage, some of these electrons reach junction 2 J and add to the minority carrier
concentration in the p-layer. This raises the reverse leakage current and results in breakdown of
junction 2 J even though the applied forward voltage is less than the breakdown voltage BO V .
With increase in gate current breakdown occurs earlier.
V-I Characteristics

A typical V-I characteristics of a thyristor is shown above. In the reverse direction the thyristor
appears similar to a reverse biased diode which conducts very little current until avalanche

DEPT OF ECE, ATMECE Page 3

Power Electronics 15EC73

breakdown occurs. In the forward direction the thyristor has two stable states ormodes of
operation that are connected together by an unstable mode that appears as anegative resistance on
the V-I characteristics. The low current high voltage region is the 1forward blocking state or the
off state and the low voltage high current mode is the on state.

For the forward blocking state the quantity of interest is the forward blocking voltage BO V
which is defined for zero gate current. If a positive gate current is applied to a thyristor then the
transition or break over to the on state will occur at smaller values of anode to cathode voltage as
shown. Although not indicated the gate current does not have to be a dc current but instead can
be a pulse of current having some minimum time duration. This ability to switch the thyristor by
means of a current pulse is the reason for wide spread applications of the device.
Holding Current H I
After an SCR has been switched to the on state a certain minimum value of anode +current is
required to maintain the thyristor in this low impedance state. If the anode current is reduced
below the critical holding current value, the thyristor cannot maintain the current through it and
reverts to its off state usually I is associated with turn off the device.
Latching Current L I
After the SCR has switched on, there is a minimum current required to sustain conduction.
This current is called the latching current. L I associated with turn on and is usually greater
than holding current.

2.3 Thyristor Gate Characteristics

The gate voltage is plotted with respect to gate current in the above characteristics. Ig(max) is the
maximum gate current that can flow through the thyristor without damaging it Similarly
Vg(max) is the maximum gate voltage to be applied. Similarly Vg (min) and Ig(min) are
minimum gate voltage and current, below which thyristor will not be turned-on. Hence to turn-on
the thyristor successfully the gate current and voltage should be

DEPT OF ECE, ATMECE Page 4

Power Electronics 15EC73

The characteristic of Fig. also shows the curve for constant gate power (Pg). Thus for reliable
turn-on, the (Vg, Ig) point must lie in the shaded area in Fig. 3.6. It turns-on thyristor
successfully. Note that any spurious voltage/current spikes at the gate must be less than Vg (min)
and Ig(min) to avoid false triggering of the thyristor. The gate characteristics shown in Fig. 3.6
are for DC values of gate voltage and current.

Instead of applying a continuous (DC) gate drive, the pulsed gate drive is used. The gate voltage
and current are applied in the form of high frequency pulses. The frequency of these pulses is
upto l0 kHz. Hence the width of the pulse can be upto 100 micro seconds. The pulsed gate drive
is applied for following reasons (advantages):

i) The thyristor has small turn-on time i.e. upto 5 microseconds. Hence a pulse of gate drive
is sufficient to turn-on the thyristor.
ii) Once thyristor turns-on, there is no need of gate drive. Hence gate drive in the form of
pulses is suitable.
iii) The DC gate voltage and current increases losses in the thyristor. Pulsed gate drive has
reduced losses.
iv) The pulsed gate drive can be easily passed through isolation transformers to isolate
thyristor and trigger circuit.

Requirement of Gate Drive

The gate drive has to satisfy the following requirements:

i) The maximum gate power should not be exceeded by gate drive, otherwise thyristor will be
damaged.

ii) The gate voltage and current should be within the limits specified by gate characteristics (Fig.
3.6) for successful turn-on

iii) The gate drive should be preferably pulsed. In case of pulsed drive the following relation
must be satisfied: (Maximum gate power x pulse width) x (Pulse frequency) ≤ Allowable
average gate power

iv) The width of the pulse should be sufficient to turn-on the thyristor successfully.

v) The gate drive should be isolated electrically from the thyristor. This avoids any damage to
the trigger circuit if in case thyristor is damaged.

DEPT OF ECE, ATMECE Page 5

Power Electronics 15EC73

vi) The gate drive should not exceed permissible negative gate to cathode voltage, otherwise the
thyristor is damaged.

vii) The gate drive circuit should not sink current out of the thyristor after turn-on.

2.4 Quantitative Analysis

Two Transistor Model

The general transistor equations are,

The SCR can be considered to be made up of two transistors as shown in above figure.
Considering PNP transistor of the equivalent circuit,

From the equivalent circuit, we see that

DEPT OF ECE, ATMECE Page 6

Power Electronics 15EC73

2.5 Switching Characteristics (Dynamic characteristics)

Thyristor Turn-ON Characteristics

When the SCR is turned on with the application of the gate signal, the SCR does not conduct
fully at the instant of application of the gate trigger pulse. In the beginning, there is no
appreciable increase in the SCR anode current, which is because, only a small portion of the

silicon pellet in the immediate vicinity of the gate electrode starts conducting. The duration
between 90% of the peak gate trigger pulse and the instant the forward voltage has fallen to
90% of its initial value is called the gate controlled / trigger delay time gd t . It is also defined
as the duration between 90% of the gate trigger pulse and the instant at which the anode
current rises to 10% of its peak value. gd t is usually in the range of 1 sec.

Thyristor Turn OFF Characteristics

DEPT OF ECE, ATMECE Page 7

Power Electronics 15EC73

When an SCR is turned on by the gate signal, the gate loses control over the device and the
device can be brought back to the blocking state only by reducing the forward current to a level
below that of the holding current. In AC circuits, however, the current goes through a natural
zero value and the device will automatically switch off. But in DC circuits, where no neutral zero
value of current exists, the forward current is reduced by applying a reverse voltage across anode
and cathode and thus forcing the current through the SCR to zero.

As in the case of diodes, the SCR has a reverse recovery time rr t which is due to charge storage
in the junctions of the SCR. These excess carriers take some time for recombination resulting in
the gate recovery time or reverse recombination time gr t . Thus, the turn-off time q t is the sum
of the durations for which reverse recovery current flows after the application of reverse voltage
and the time required for the recombination of all excess carriers present. At the end of the turn
off time, a depletion layer develops across 2 J and the junction can now with stand the forward
voltage. The turn off time is dependent on the anode current, the magnitude of reverse g V
applied ad the magnitude and rate of application of the forward voltage. The turn off time for
convert grade SCR’s is 50 to 100 sec and that for inverter grade SCR’s is 10 to 20 sec.
To ensure that SCR has successfully turned off , it is required that the circuit off time c t be
greater than SCR turn off time q t .
Thyristor Turn ON
Thermal Turn on: If the temperature of the thyristor is high, there will be an increase in charge
carriers which would increase the leakage current. This would cause an increase in 1 & 2 and the
thyristor may turn on. This type of turn on many cause thermal run away and is usually avoided.
Light: If light be allowed to fall on the junctions of a thyristor, charge carrier concentration
would increase which may turn on the SCR.
LASCR: Light activated SCRs are turned on by allowing light to strike the silicon wafer.
High Voltage Triggering: This is triggering without application of gate voltage with only
application of a large voltage across the anode-cathode such that it is greater than the forward
breakdown voltage BO V . This type of turn on is destructive and should be avoided.
Gate Triggering: Gate triggering is the method practically employed to turn-on the thyristor.
Gate triggering will be discussed in detail later.
Triggering: Under transient conditions, the capacitances of the p-n junction will influence the
characteristics of a thyristor. If the thyristor is in the blocking state, a rapidly rising voltage
applied across the device would cause a high current to flow through the device resulting in turn-
on. If
j2 i is the current throught the junction 2 j and
j2 C is the junction capacitance and
j2 V is the voltage across 2 j , then

DEPT OF ECE, ATMECE Page 8

Power Electronics 15EC73

Thyristor Ratings

VOLTAGE RATINGS

VDWM : This specifies the peak off state working forward voltage of the device. This specifies
the maximum forward off state voltage which the thyristor can withstand during its working.

VDRM : This is the peak repetitive off state forward voltage that the thyristor can block
repeatedly in the forward direction (transient).

VDSM : This is the peak off state surge / non-repetitive forward voltage that will occur across
the thyristor.

VRWM : This the peak reverse working voltage that the thyristor can withstand in the reverse
direction.

VRRM : It is the peak repetitive reverse voltage. It is defined as the maximum permissible
instantaneous value of repetitive applied reverse voltage that the thyristor can block in
reverse direction.

VRSM : Peak surge reverse voltage. This rating occurs for transient conditions for a specified
time duration.

VT : On state voltage drop and is dependent on junction temperature.

VTM : Peak on state voltage. This is specified for a particular anode current and junction
temperature.
rating: This is the maximum rate of rise of anode voltage that the SCR has to withstand

and which will not trigger the device without gate signal.

Current Rating
I Taverage : This is the on state average current which is specified at a particular temperature.
I TRMS : This is the on-state RMS current.

Latching current, I L : After the SCR has switched on, there is a minimum current required to
sustain conduction. This current is called the latching current. I L associated with turn on and
is usually greater than holding current

DEPT OF ECE, ATMECE Page 9

Power Electronics 15EC73

Holding current, I H : After an SCR has been switched to the on state a certain minimum
value of anode current is required to maintain the thyristor in this low impedance state. If the
anode current is reduced below the critical holding current value, the thyristor cannot
maintain the current through it and reverts to its off state usually I H.
Gate Specifications
I GT : This is the required gate current to trigger the SCR. This is usually specified as a DC
value.
VGT : This is the specified value of gate voltage to turn on the SCR (dc value).
VGD : This is the value of gate voltage, to switch from off state to on state. A value below this
will keep the SCR in off state.
QRR : Amount of charge carriers which have to be recovered during the turn off process.
Rthjc : Thermal resistance between junction and outer case of the device.

2.6 Gate Triggering Methods

Types
The different methods of gate triggering are the following
 R-triggering.
 RC triggering.

 UJT triggering
Resistance Triggering
A simple resistance triggering circuit is as shown. The resistor 1 R limits the current through the
gate of the SCR. 2 R is the variable resistance added to the circuit to achieve control over the
triggering angle of SCR. Resistor ‘R’ is a stabilizing resistor. The diode D is required to ensure
that no negative voltage reaches the gate of the SCR.

DEPT OF ECE, ATMECE Page 10

Power Electronics 15EC73

Resistance Capacitance Triggering

RC Half Wave
Capacitor ‘C’ in the circuit is connected to shift the phase of the gate voltage. 1 D is used to
prevent negative voltage from reaching the gate cathode of SCR.
In the negative half cycle, the capacitor charges to the peak negative voltage of the supply m V
through the diode 2 D . The capacitor maintains this voltage across it, till the supply voltage
crosses zero. As the supply becomes positive, the capacitor charges through resistor ‘R’ from
initial voltage of m V , to a positive value. When the capacitor voltage is equal to the gate trigger
voltage of the SCR, the SCR is fired and the capacitor voltage is clamped to a small positive
value.

DEPT OF ECE, ATMECE Page 11

Power Electronics 15EC73

Case 1: R Large.
When the resistor ‘R’ is large, the time taken for the capacitance to charge from m V to gt V is
large, resulting in larger firing angle and lower load voltage.
Case 2: R Small
When ‘R’ is set to a smaller value, the capacitor charges at a faster rate towards gt V resulting in
early triggering of SCR and hence L V is more. When the SCR triggers, the voltage drop across it
falls to 1 – 1.5V. This in turn lowers; the voltage across R & C. Low voltage across the SCR
during conduction period keeps the capacitor discharge during the positive half cycle.

UNI-JUNCTION TRANSISTOR (UJT)

UJT is an n-type silicon bar in which p-type emitter is embedded. It has three terminals base1,
base2 and emitter ‘E’. Between 1 B and 2 B UJT behaves like ordinary resistor and the internal
resistances are given as B1 R and B2 R with emitter open BB B1 B2 R R R . Usually the p-region
is heavily doped and n-region is lightly doped. The equivalent circuit of UJT is as shown. When
BB V is applied across 1 B and 2 B , we find that potential at A is

DEPT OF ECE, ATMECE Page 12

Power Electronics 15EC73

Operation
When voltage BB V is applied between emitter ‘E’ with base 1 1 B as reference and the emitter
voltage E V is less than D BE V V the UJT does not conduct. D BB V V is designated as P V
which is the value of voltage required to turn on the UJT. Once E V is equal to P BE D V V ,
then UJT is forward biased and it conducts. The peak point is the point at which peak current P I
flows and the peak voltage P V is across the UJT. After peak point the current increases but
voltage across device drops, this is due to the fact that emitter starts to inject holes into the lower
doped n-region. Since p-region is heavily doped compared to n-region. Also holes have a longer
life time, therefore number of carriers in the base region increases rapidly. Thus potential at ‘A’
falls but current E I increase rapidly. B1 R acts as a decreasing resistance. The negative
resistance region of UJT is between peak point and valley point. After valley point, the device
acts as a normal diode since the base region is saturated and B1 R does not decrease again.

(i) Expression for period of oscillation„t‟

The period of oscillation of the UJT can be derived based on the voltage across the capacitor. Here
we assume that the period of charging of the capacitor is lot larger than than the discharging time.
Using initial and final value theorem for voltage across a capacitor, we get

DEPT OF ECE, ATMECE Page 13

Power Electronics 15EC73

2.7 Assignment Questions

1 Distinguish between latching current and holding current.

2. Converter grade and inverter grade thyristors
3. Thyristor turn off and circuit turn off time
4. Peak repetitive forward blocking voltage i2 t rating
5. Explain the turn on and turn of dynamic characteristics of thyristor
6. A string of series connected thyristors is to withstand a DC voltage of 12 KV. The
maximum leakage current and recovery charge differences of a thyristors are 12 mA and
120 µC respectively. A de-rating factor of 20% is applied for the steady state and
dynamic (transient) voltage sharing of the thyristors. If the maximum steady sate voltage
is 1000V, determine 1) the steady voltage sharing resistor R for each thyristor. 2) the
transient voltage capacitor C1 for each thryristor
7. A SCR is to operate in a circuit where the supply voltage is 200 VDC. The dv/dt should
be limited to 100 V/ µs. Series R and C are connected across the SCR for limiting dv/dt.
The maximum discharge current from C into the SCR, if and when it is turned ON is to
be limited to 100 A. Using an approximate expression, obtain the values of R and C.
8. With the circuit diagram and relevant waveforms,

2.8 Generic Skills / Outcomes:

 TO know working of thyristors with the characteristics and comparison with

the transistor.
 How to trigger the thyristor using different methods.

2.9 Further Reading

1. http://books.google.co.in/books/about/Power_Electronics.html?id=-WqvjxMXClAC
2. http://www.flipkart.com/power-electronic-2ed/p/itmczynuyqnbvzzj
3. http://www.scribd.com/doc/36550374/Power-Electronics-Notes
4. http://elearning.vtu.ac.in/EC42.html
5. http://www.onlinevideolecture.com/electrical-engineering/nptel-iit-bombay/power-
electronics/?course_id=510

DEPT OF ECE, ATMECE Page 14