See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/323683430

Communicating with Raspberry Pi via MAVLink

Preprint · July 2017

DOI: 10.13140/RG.2.2.21398.65606

CITATIONS READS

0 7,199

1 author:

Saif Aldeen Saad Alkadhim

Shiite endowment Divan
111 PUBLICATIONS   263 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

IEEE-CoDIT'20 conference (Parague, Czech Republic, 2020) View project

BIM and AGILE Approach for Construction Projects View project

All content following this page was uploaded by Saif Aldeen Saad Alkadhim on 10 March 2018.

The user has requested enhancement of the downloaded file.

 Communicating with Raspberry Pi via MAVLink
Saif Aldeen Saad Obayes Al-Kadhim
MIEEE
[email protected]
[email protected]

Abstract
This paper explains how to connect and configure a Raspberry Pi so that it is able to
communicate with a Pixhawk flight controller using the MAVLink protocol over a serial
connection. This can be used to perform additional tasks such as image recognition which
simply cannot be done by the Pixhawk due to the memory requirements for storing images.

Key Words: Raspberry Pi, flight controller, MAVLink, Pixhawk.

1. Connecting the Pixhawk and Raspberry Pi

Connect the Pixhawk’s TELEM2 port to the Raspberry Pi Ground, TX and RX pins as shown
in the image above. More details on the individual Raspberry Pi pin functions can be
found here. The Raspberry Pi can be powered by connecting the red V+ cable to the +5V pin
(as shown above) or from USB in (for example, using a separate 5V BEC hooked up to the
USB power). Powering via USB is recommended as it is typically safer - because the input is
regulated. If powering via USB, do not also connect the +5V pin as shown (still connect
common ground).

Figure 1 Connecting Pixhawak with Raspberry Pi

 1.1 Setup the Raspberry Pi

The easiest way to setup the Raspberry Pi is to flash one of the existing :ref:`APSync <apsync-
intro>` images:

1. purchase a formatted 8GB or 16GB SD card (16GB is better because some 8GB cards
will not be quite large enough to fit the image) and insert into your laptop/desktop
computer's SD card slot
2. download the latest image from firmware.ardupilot.org. Look for the file starting with
"apsync-Raspberry Pi".
3. extract the image. On Windows you may use 7-zip.
4. For Windows download and install Win32DiskImager and follow the instructions
here.
5. For Linux follow these instructions.
6. For Mac follow these instructions.

When extracting the contents of the compressed file on Mac you may get into an infinite loop
of extraction (.xz to .cpgz and vice versa) using the default Archiver. In order to correctly
extract the .img file you will need to use the Unarchive (http://unarchiver.c3.cx/unarchiver).

1.2 Setting up the Pixhawk

Connect to the Pixhawk with a ground station (i.e. Mission Planner) and set the following
parameters:

1. :ref:`SERIAL2_PROTOCOL <copter:SERIAL2_PROTOCOL>` = 1 (the default) to

enable MAVLink on the serial port.
2. :ref:`SERIAL2_BAUD <copter:SERIAL2_BAUD>` = 921 so the Pixhawk can
communicate with the Raspberry Pi at 921600 baud.
3. :ref:`LOG_BACKEND_TYPE <copter:LOG_BACKEND_TYPE>` = 3 if you are
using APSync to stream the dataflash log files to the Raspberry Pi.

1.3 Connecting to Raspberry Pi with an SSH/Telnet client

These steps assume that you have set-up your Raspberry Pi so that it is running Raspbian.
These instructions are not required if you are using APSync as described above.To avoid the
requirement to plug a keyboard, mouse and HDMI screen into your Raspberry Pi it is
convenient to be able to connect from your Desktop/Laptop computer to your Raspberry Pi
using an SSH/Telnet client such as PuTTY.

1. Connect the Raspberry Pi to your local network by one of the following methods:

o Connecting an Ethernet LAN cable from the Raspberry Pi board to your

Ethernet router, or
 o Use a USB dongle to connect your Raspberry Pi to the local wireless network,
or

o Connect the Ethernet LAN cable between the Raspberry Pi and your
desktop/laptop computer. Open the control panel's Network and Sharing
Center, click on the network connection through which your desktop/laptop is
connected to the internet, select properties and then in the sharing tab, select
"Allow other networks to connect through this computer's Internet connection"

Figure 2 Connect the Ethernet LAN cable between the Raspberry Pi and desktop or laptop computer

2. Determine the Raspberry Pi IP address:

o If you have access to the Raspberry Pi terminal screen (i.e.you have a screen,
keyboard, mouse connected) you can use the /sbin/ifconfig command.
o If your Ethernet router has a web interface it may show you the IP address of
all connected devices.
 Figure 3 Determine the Raspberry Pi IP address

3. Connect with Putty:

If all goes well you should be presented with the regular login prompt to which you
can enter the username/password which defaults to pi/raspberry

Figure 4 Putty software configurations.

 1.4 Install the required packages on the Raspberry Pi

Log into the Raspberry Pi board (default username password is pi/raspberry) and check that its
connection to the internet is working:

ping google.com

OR

ping 173.194.126.196

If the first fails but the second succeeds, then there is a problem with the DNS server that your
Raspberry Pi is attempting to use. Please edit the /etc/resolv.conf file and add the IP address of
a nearby DNS server. During the creation of this wiki, the first two parts of the desktop
machine's IP address plus ".1.1" worked. To stop other processes from later updating this file
you may wish to run the chattr +i /etc/resolv.conf command (this can be undone later with
chattr -i /etc/resolv.conf). That sets the "immutable" bit on resolv.conf to prevent other
software from updating it.

After the internet connection is confirmed to be working install these packages:

sudo apt-get update #Update the list of packages in the software center

sudo apt-get install screen python-wxgtk2.8 python-matplotlib python-opencv python-pip python-numpy

python-dev libxml2-dev libxslt-dev

sudo pip install future

sudo pip install pymavlink

sudo pip install mavproxy

The packages are :ref:`mostly the same as when setting up SITL <setting-up-sitl-on-
windows>`. Reply Reply 'y' when prompted re additional disk space.

1.5 Disable the OS control of the serial port

Use the Raspberry Pi configuration utility for this.

Type:
sudo raspi-config

And in the utility, select "Advanced Options":

RasPiConfiguration Utility: Serial Settings: Advanced Options

And then "Serial" to disable OS use of the serial connection:

Reboot the Raspberry Pi when you are done.

 Figure 5 Raspberry Pi configuration utility

2. Testing the connection

To test the Raspberry Pi and Pixhawk are able to communicate with each other first ensure the
Raspberry Pi and Pixhawk are powered, then in a console on the Raspberry Pi type:

sudo -s

mavproxy.py --master=/dev/ttyAMA0 --baudrate 57600 --aircraft MyCopter

On newer versions of Raspberry Pi 3 the uart serial connection may be disable by default. In
order to enable serial connection on the Raspberry Pi edit /boot/config.txt and set
enable_uart=1. the build-in serial port is /dev/ttyS0.
Once MAVProxy has started you should be able to type in the following command to display
the ARMING_CHECK parameters value
param show ARMING_CHECK

param set ARMING_CHECK 0

arm throttle

If you get an error about not being able to find log files or if this example otherwise doesn't run
properly, make sure that you haven't accidentally assigned these files to another username, such
as Root.

Entering the following at the Linux command line will ensure that all files belong to the
standard Pi login account:

sudo chown -R pi /home/pi

Figure 6 Testing the connection

3. Configure MAVProxy to always run

To setup MAVProxy to start whenever the Raspberry Pi is restarted open a terminal window
and edit the /etc/rc.local file, adding the following lines just before the final "exit 0" line:

date

echo $PATH

PATH=$PATH:/bin:/sbin:/usr/bin:/usr/local/bin
export PATH

cd /home/pi

screen -d -m -s /bin/bash mavproxy.py --master=/dev/ttyAMA0 --baudrate 57600 --aircraft

MyCopter

) > /tmp/rc.log 2>&1

exit 0

Whenever the Raspberry Pi connects to the Pixhawk, three files will be created in the
/home/pi/MyCopter/logs/YYYY-MM-DD directory:

 mav.parm : a text file with all the parameter values from the Pixhawk
 flight.tlog : a telemetry log including the vehicles altitude, attitude, etc which can be
opened using the mission planner (and a number of other tools)
 flight.tlog.raw : all the data in the .tlog mentioned above plus any other serial data
received from the Pixhawk which might include non-MAVLink formatted messages
like startup strings or debug output

If you wish to connect to the MAVProxy application that has been automatically started you
can log into the Raspberry Pi and type:

sudo screen -x

To learn more about using MAVProxy please read the MAVProxy documentation.

It is also worth noting that MAVProxy can do a lot more than just provide access to your
Pixhawk. By writing python extension modules for MAVProxy you can add sophisticated
autonomous behaviour to your vehicle. A MAVProxy module has access to all of the sensor
information that your Pixhawk has, and can control all aspects of the flight. To get started with
MAVProxy modules please have a look at the existing modules in the MAVProxy source code.

4. Installing DroneKit on Raspberry Pi

The most up-to-date instructions for Installing DroneKit on Linux are in the DroneKit-Python
documentation. This information is a summary, and might go out of date.

To install DroneKit-Python dependencies (most of which will already be present from when
you installed MAVProxy) and set DroneKit to load when MAVProxy starts:

sudo apt-get install python-pip python-dev python-numpy python-opencv python-serial

python-pyparsing python-wxgtk2.8 libxml2-dev libxslt-dev

sudo pip install droneapi

echo "module load droneapi.module.api" >> ~/.mavinit.scr

Then open the MAVProxy terminal in the location where your DroneKit script is located and
start an example:
MANUAL> api start vehicle_state.py

If you get a warning that droneapi module has not loaded, you can do so manually in
MAVProxy:

MANUAL> module load droneapi.module.api

5. Connecting with the Mission Planner

The Pixhawk will respond to MAVLink commands received through Telemetry 1 and
Telemetry 2 ports (see image at top of this page) meaning that both the Raspberry Pi and the
regular ground station (i.e. Mission planner, etc) can be connected. In addition it is possible to
connect the Mission Planner to the MAVProxy application running on the Raspberry
Pi :ref:`similar to how it is done for SITL <setting-up-sitl-on-
windows_connecting_with_the_mission_planner>`.

Primarily this means adding an --out <ipaddress>:14550 to the MAVProxy startup command
with the being the address of the PC running the mission planner. On windows the ipconfig can
be used to determine that IP address. On the computer used to write this wiki page the
MAVProxy command became:

mavproxy.py --master=/dev/ttyAMA0 --baudrate 57600 --out 192.168.137.1:14550 --aircraft

MyCopter

Connecting with the mission planner is shown below:

Figure 7 the mission planner dashboard

 References:
1. Saif Aldeen Saad Obayes Al-Kadhim, and et al., Prototype Wireless Controller System
based on Raspberry Pi and Arduino for Engraving Machine, UKSim-AMSS 19th
International Conference on Modelling & Simulation, DOI: 10.1109/UKSim.2017.20.
2. Saif Aldeen Saad Obayes Al-Kadhim, Industrial Workshop Based on Internet of
Things: Automated Manufacturing Systems Technology, Noor Publishing (August 1,
2017), ISBN-10: 3330965754, ISBN-13: 978-3330965751.
3. Saif Aldeen Saad Obayes Al-Kadhim, and et al., CNC Machine Based on Embedded
Wireless and Internet of Things for Workshop Development Article in IJCDS Journal
Volume 6(Issue 4):205 · July 2017, DOI: 10.12785/ijcds/060406.

View publication stats