BS EN 10228-4:2016

EN 10228-4:2016 (E)

Contents Page

European foreword....................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 5
4 Mandatory information ................................................................................................................................ 6
5 Test procedure ................................................................................................................................................. 6
5.1 General ................................................................................................................................................................ 6
5.2 Form ..................................................................................................................................................................... 6
5.3 Content ................................................................................................................................................................ 7
6 Personnel qualification ................................................................................................................................. 7
7 Equipment and accessories ......................................................................................................................... 7
7.1 Instrument ......................................................................................................................................................... 7
7.2 Probes.................................................................................................................................................................. 7
7.2.1 General ................................................................................................................................................................ 7
7.2.2 Contouring ......................................................................................................................................................... 8
7.2.3 Nominal frequency ......................................................................................................................................... 8
7.2.4 Normal-beam probes ..................................................................................................................................... 8
7.2.5 Angle-beam probes......................................................................................................................................... 8
7.2.6 Dual-element probes ..................................................................................................................................... 8
7.3 Calibration blocks ........................................................................................................................................... 8
7.4 Reference blocks ............................................................................................................................................. 8
7.5 Couplant.............................................................................................................................................................. 8
8 Routine calibration and checking ............................................................................................................. 9
9 Stage of manufacture ..................................................................................................................................... 9
10 Surface condition ............................................................................................................................................ 9
10.1 General ................................................................................................................................................................ 9
10.2 Surface finish related to quality class ...................................................................................................... 9
10.3 As-forged surface condition ........................................................................................................................ 9
11 Test sensitivity .............................................................................................................................................. 10
11.1 General ............................................................................................................................................................. 10
11.2 Normal-beam probes .................................................................................................................................. 10
11.3 Angle-beam probes...................................................................................................................................... 10
11.4 Repeat testing ................................................................................................................................................ 10
12 Scanning .......................................................................................................................................................... 10
12.1 General ............................................................................................................................................................. 10
12.2 Complex forgings .......................................................................................................................................... 11
12.3 Grid scanning coverage .............................................................................................................................. 11
12.4 100 % scanning coverage .......................................................................................................................... 11
12.5 Scanning speed.............................................................................................................................................. 11
13 Classification .................................................................................................................................................. 14
13.1 Classification of indications ..................................................................................................................... 14
13.2 Classification of discontinuities .............................................................................................................. 16

2
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

14 Recording levels and acceptance criteria ............................................................................................ 19

15 Sizing ................................................................................................................................................................. 20
16 Test report ...................................................................................................................................................... 21
Annex A (informative) Maximum testable depth for corresponding beam path range for
circumferential angle-beam scans ......................................................................................................... 22
Annex B (informative) Amplitude of indication in dB relative to % DAC .............................................. 24
Annex C (informative) Significant technical changes to the version EN 10228-4:1999 ................... 25

3
BS EN 10228-4:2016
EN 10228-4:2016 (E)

European foreword

This document (EN 10228-4:2016) has been prepared by Technical Committee ECISS/TC 111 “Steel
castings and forgings”, the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2016 and conflicting national standards
shall be withdrawn at the latest by December 2016.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.

This document supersedes EN 10228-4:1999.

Annex C provides the significant technical changes to the previous version EN 10228-4:1999.

EN 10228 consists of the following parts under the general title Non-destructive testing of steel forgings:

— Part 1: Magnetic particle inspection;

— Part 2: Penetrant testing;

— Part 3: Ultrasonic testing of ferritic or martensitic steel forgings;

— Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

4
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

1 Scope
This European Standard describes techniques for the manual, pulse-echo, ultrasonic testing of forgings
manufactured from austenitic and austenitic-ferritic stainless steels. Mechanized scanning techniques,
such as immersion testing, may be used but should be agreed between the purchaser and supplier (see
Clause 4).
This part of EN 10228 applies to four types of forgings, classified according to their shape and method
of production. Types 1, 2 and 3 are essentially simple shapes. Type 4 covers complex shapes.
This part of EN 10228 does not apply to:
— closed die forgings;

— turbine rotor and generator forgings.

Ultrasonic testing of ferritic and martensitic steel forgings is the subject of Part 3 of this European
Standard.

2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1330-1, Non destructive testing - Terminology - Part 1: List of general terms

EN 1330-4, Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing

EN 12668-1, Non-destructive testing - Characterization and verification of ultrasonic examination

equipment - Part 1: Instruments

EN 12668-2, Non-destructive testing - Characterization and verification of ultrasonic examination

equipment - Part 2: Probes

EN 12668-3, Non-destructive testing - Characterization and verification of ultrasonic examination

equipment - Part 3: Combined equipment

EN ISO 2400, Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 1
(ISO 2400)

EN ISO 9712, Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712)

EN ISO 16811, Non-destructive testing - Ultrasonic testing - Sensitivity and range setting (ISO 16811)

EN ISO 16827, Non-destructive testing - Ultrasonic testing - Characterization and sizing of discontinuities
(ISO 16827)

3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 1330-1 and EN 1330-4 apply.

5
BS EN 10228-4:2016
EN 10228-4:2016 (E)

4 Mandatory information
The following aspects concerning ultrasonic testing shall be agreed between the purchaser and supplier
at the time of the enquiry or order:
a) the manufacturing stage(s) at which ultrasonic testing shall be performed (see Clause 9);

b) the volume(s) to be tested and whether grid scanning coverage or 100 % scanning coverage is
required (see Clause 12);

c) whether near surface testing is required (see 7.2.6);

d) the quality class required, or the quality classes and the zones to which they apply (see Clause 14);

e) the applicable recording/acceptance criteria if different from those detailed in Table 5, Table 6 or
Table 7;

f) whether any special scanning coverage, equipment or couplant is required in addition to that
detailed in Clauses 7 and 12;

g) the scanning technique to be used if not manual (see Clause 1);

h) the sizing techniques to be used for extended discontinuities (see Clause 15);

i) the technique(s) to be used for setting sensitivity (see Clause 11);

j) whether the test shall be conducted in the presence of the purchaser or his representative;

k) whether a written procedure shall be submitted for approval by the purchaser (see Clause 5);

l) whether testing by angle-beam probes is required (see 11.3);

m) the remaining test requirements for complex forgings (type 4) (see 12.2).

5 Test procedure

5.1 General

Ultrasonic testing shall be performed in accordance with a written test procedure. Where specified in
the enquiry or order, the written test procedure shall be submitted to the purchaser for approval prior
to the test.
5.2 Form

The written test procedure shall be one of the following:

a) a product specification;

b) a test procedure written specifically for the application;

c) this part of EN 10228 may be used if it is accompanied by examination details specific to the
application.

6
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

5.3 Content

The written test procedure shall contain the following details as minimum requirements:
a) description of the forgings to be tested;

b) reference documents;

c) qualification of testing operator;

d) stage of manufacture at which the test is carried out;

e) testing zones specified in terms of the applicable quality classes;

f) preparation of scanning surfaces;

g) couplant;

h) description of the test equipment;

i) calibration and checking of the test equipment;

j) scanning plan;

k) description and sequence of testing operations;

l) recording levels;

m) characterization of discontinuities;

n) acceptance criteria;

o) test report.

6 Personnel qualification
Personnel shall be qualified in accordance with the requirements detailed in EN ISO 9712.

7 Equipment and accessories

7.1 Instrument

The ultrasonic instrument shall feature A-scan presentation and shall conform to EN 12668-1.
7.2 Probes

7.2.1 General

Probes used for the initial detection of discontinuities shall conform to EN 12668-2. Where
supplementary probes are used for purposes other than the initial detection of discontinuities, they
need not conform to EN 12668-2.

7
BS EN 10228-4:2016
EN 10228-4:2016 (E)

7.2.2 Contouring

When required, probes shall be contoured in accordance with EN ISO 16811.

7.2.3 Nominal frequency

Probes shall have a nominal frequency in the range from 0,5 MHz to 6 MHz.
7.2.4 Normal-beam probes

Effective transducer diameter shall be in the range from 10 mm to 40 mm.

7.2.5 Angle-beam probes

For the transverse waves, the angle-beam probes shall be in the range from 35° to 70°.
Effective transducer area shall be in the range from 20 mm2 to 625 mm2.
7.2.6 Dual-element probes

If near-surface testing is required, then dual-element probes shall be used.

7.3 Calibration blocks

Calibration blocks shall conform to the requirements detailed in EN ISO 2400.

7.4 Reference blocks

Reference blocks shall be used when sensitivity shall be established by the distance-amplitude curve
(DAC) technique and/or when discontinuities shall be sized in terms of amplitude relative to reference
reflectors by the DAC technique. The surface condition of the reference block shall be representative of
the surface condition of the object to be tested. Unless otherwise specified the reference block shall
contain at least three reflectors covering the entire depth range being tested.
The reference block shall be manufactured from one of the following:
a) an excess length of the object to be tested;

b) a part of the same material and with the same heat treatment condition as the object to be tested;

c) a part having similar acoustic properties to the object to be tested.

The choice of a test block with similar acoustic properties should be to the appreciation of a Level 2
qualified person.
Reference blocks shall not be used for the distance-gain-size (DGS) technique other than for checking
the accuracy of a particular DGS diagram.
Reflector sizes different from those detailed in Tables 5 and 6 may be used as long as the test sensitivity
is corrected accordingly.
7.5 Couplant

The same type of couplant shall be used for the setting of range and sensitivity, for scanning and for the
assessment of discontinuities.
NOTE Examples of suitable couplants are: water (with or without corrosion inhibitor or softener), grease, oil,
glycerol and water cellulose paste.

8
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

After the test, couplant shall be removed if its presence could adversely affect later manufacturing or
testing operations or the integrity of the test object.

8 Routine calibration and checking

The combined equipment (instrument and probes) shall be calibrated and checked in accordance with
the requirements detailed in EN 12668-3.

9 Stage of manufacture
Ultrasonic testing shall be performed after the final heat treatment unless otherwise agreed at the time
of enquiry or order (see Clause 4), e.g. at the latest possible stage of manufacture for areas of the forging
which are not practicable to test after the final heat treatment.
For both cylindrical and rectangular forgings, which shall be bored, it is recommended to carry out
ultrasonic testing before boring.

10 Surface condition

10.1 General

Surfaces to be scanned shall be free from paint, non-adhering scale, dry couplant, surface irregularities
or any other substance which could reduce coupling efficiency, hinder the free movement of the probe
or cause errors in interpretation.
10.2 Surface finish related to quality class

In the machined condition, for testing to quality classes 1 and 2, a surface finish corresponding to a
roughness Ra ≤ 12,5 µm shall be produced and for testing of quality class 3, a surface finish
corresponding to a roughness Ra ≤ 6,3 µm shall be produced.

a
Table 1 — Surface finish related to quality class

Quality class and roughness Ra

Surface finish 1 2 3
≤ 12,5 μm ≤ 6,3 μm
Machined X X
a
“X” signifies the quality class that can be achieved in machined conditions.

10.3 As-forged surface condition

Where forgings are supplied in the as-forged surface condition they shall be considered acceptable
providing the specified quality class can be achieved. When it is not practical to perform a
comprehensive test onnas-forged surfaces, shot blasting, sand blasting or surface grinding shall be used
to ensure that acoustic coupling can be maintained.
NOTE Only quality class 1 is normally applicable.

9
BS EN 10228-4:2016
EN 10228-4:2016 (E)

11 Test sensitivity

11.1 General

Test sensitivity shall be sufficient to ensure the detection of the smallest discontinuities required by the
recording levels (see Table 5 and when required, Tables 6 or 7). If the required sensitivity cannot be
achieved due to coarse grain size, acceptance of the forging shall be subject to agreement between the
purchaser and supplier.
11.2 Normal-beam probes

For normal-beam probes, one of the following techniques shall be used to establish the sensitivity for
scanning:
a) Distance-amplitude curve (DAC) technique, based upon the use of side-drilled holes (flat-bottomed
holes possible);

b) Distance-gain-size (DGS) technique (disc-shaped reflectors).

The procedure to be used in each case shall be in accordance with EN ISO 16811.
11.3 Angle-beam probes

For angle-beam probes one of the following techniques shall be used to establish the sensitivity for
scanning:
a) DAC technique using 3 mm diameter side-drilled holes;

b) DGS technique (disc-shaped reflectors).

The procedure to be used in each case shall be as detailed in EN ISO 16811.

The DAC and DGS techniques shall not be compared for angle-beam probes.
11.4 Repeat testing

Where repeat testing is performed the same method of establishing sensitivity (DAC or DGS) shall be
used as was initially used.

12 Scanning

12.1 General

Scanning shall be performed using the manual contact pulse-echo technique.

The minimum scanning coverage required is dictated by the type of forging and whether grid scanning
coverage or 100 % scanning coverage has been specified in the enquiry or order (see Clause 4).
Table 2 classifies four types of forging according to their shapes and method of production.
Table 3 specifies the requirements for normal-beam probes for forging types 1, 2 and 3.
Table 4 specifies the requirements for angle-beam probes for forging types 3a, 3b and 3c which have an
outside diameter to inside diameter ratio less than 1,6:1. The effective depth of circumferentially
oriented angle-beam scans is limited by the beam angle and the forging diameter (see Annex A).

10
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

12.2 Complex forgings

For complex shaped forgings or complex shaped parts of forgings (type 4) and small diameter forgings,
test requirements shall include, as a minimum, the required beam angles, scanning directions and
extent of scanning coverage (grid or 100 %). The remaining test requirements shall be agreed between
purchaser and supplier (see Clause 4, m)).
12.3 Grid scanning coverage

Grid scanning shall be performed with the probe or probes traversed along the grid lines defined in
Tables 3 and 4.
Where recordable indications are revealed by grid scanning, additional scanning shall be performed to
determine the extent of the indications.
12.4 100 % scanning coverage

100 % scanning coverage shall be performed over the surfaces specified in Tables 3 and 4. Consecutive
probe traverses shall overlap by at least 10 % of the effective beam diameter.
12.5 Scanning speed

Manual scanning speed shall not exceed 150 mm/s.

11
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Table 2 — Classification of forgings according to their shape and method of production

Type Shape Method of production

1aa Elongated with round or approximately
round section, e.g. bars, rods, cylinders,
shafts, journals, discs cut from bars

1ba Elongated with rectangular or Direct forged

approximately rectangular section, e.g.
bars, rods, blocks, sections cut from
bars

2b Flattened, e.g. discs, plate, flywheels

Upset

3a Hollow cylindrical shapes, e.g. bottles

compressed gas tanks

Mandrel forged

3b Hollow cylindrical shapes, e.g. rings,

flanges, rims

Expanded

3c Ring rolling
All forgings or parts of forgings with
4 At the manufacturer’s discretion
complex shape
a Type 1 forgings may incorporate bores of small diameter relative to the major dimensions.
b Type 2 forgings may eventually be drilled (e.g. binding discs).

12
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

Table 3 — Scanning coverage with normal-beam probes

Type Grid scanninga 100 % Scanninga, b

1 1a Diameter, D, (mm) Scan
linesc
D ≤ 200 2 at 90° Scan 100 % around at least
200 < D ≤ 500 3 at 60° 180° of cylindrical surface
500 < D ≤ 1 000 4 at 45°
1 000 < D 6 at 30°
1b
Scan along the lines of a
square-link grid on two
perpendicular Scan 100 % on two
surfacesc, d perpendicular surfaces

2 Scan along the lines of a Scan 100 % around at least

square-link grid around 360° 180° on the cylindrical
on the cylindrical surface and surface and 100 % of one
one lateral surfaced lateral surface
3 3a

Scan along the lines of a

square-link grid around 360° Scan 100 % around 360° on
on the outer cylindrical the outer cylindrical surface
surfaced

3b and 3c Scan along the lines of a Scan 100 % around 360° on

square-link grid around 360° the outer cylindrical surface
on the outer cylindrical surface and one lateral surface
and one lateral surfaced

4 Scanning coverage shall be specified in the enquiry or order

a Additional scanning (for example in both axial directions for type 3a) may be carried out if specified in the
enquiry or order.
b 100 % means at least 10 % beam overlap between consecutive probe traverses.
c For types 1a or 1b, if the presence of a bore prevents the opposite surface being reached, the number of scan
lines shall be doubled symmetrically.
d The grid line separation shall be equal to the part thickness, up to a maximum of 200 mm.

13
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Table 4 — Scanning coverage with angle-beam probes

Type Grid scanninga 100 % scanninga, b

3c 3a

Scan in both
directions along 360°
Scan in both
circumferential grid
circumferential
lines, the separation
directions over
3b of which is equal to
100 % on the outer
the radial thickness
cylindrical surface
up to a maximum of
200 mm

4 Scanning coverage shall be specified in the enquiry or order

a Additional scanning coverage may be carried out if specified in the enquiry or order.
b 100 % means at least 10 % beam overlap between consecutive probe traverses.
c For forgings type 3c this test procedure is normally not used, but it may be agreed at time of enquiry.

13 Classification

13.1 Classification of indications

Where practicable, classification of indications according to their echodynamic pattern shall be made by
scanning from a minimum of two mutually perpendicular directions.
a) Pattern 1:

As the probe is moved, the A-scan display shows a single sharp indication rising smoothly in
amplitude to a maximum and then falling smoothly to zero (see Figure 1a)).

This A-scan display in combination with the echodynamic pattern in Figure 1b) obtained from the
side-drilled holes used to plot the beam profile, corresponds to discontinuity dimensions smaller
than or equal to the −6 dB beam profile.

14
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

a) A-scan presentation b) Echodynamic pattern

Key
a) X pattern of A-Scan at fixed probe position (at typical probe position)
b) X pattern of curve amplitude against probe shift (variation in signal amplitude as probe is moved)
Y amplitude

Figure 1 — Pattern 1 - A-scan presentation and echo envelope presentation

b) Pattern 2:

As the probe is moved, the A-scan display shows a single sharp indication rising smoothly in
amplitude to a maximum and then falling smoothly to zero (see Figure 2 a)). This A-scan display in
combination with the echodynamic pattern in Figure 2 b) obtained from the side-drilled holes used
to plot the beam profile, corresponds to discontinuity dimensions greater than the to −6 dB beam
profile.

15
BS EN 10228-4:2016
EN 10228-4:2016 (E)

a) A-scan presentation b) Echodynamic pattern

Key
a) X pattern of A-Scan at fixed probe position (at typical probe position)
b) X pattern of curve amplitude against probe shift (variation in signal amplitude as probe is moved)
Y amplitude

Figure 2 — Pattern 2 - A-scan presentation and echo envelope presentation

13.2 Classification of discontinuities

Discontinuities shall be classified according to their echodynamic patterns as follows:

a) Point-like discontinuity:

Echodynamic pattern 1 and/or dimension equal to or less than the −6 dB beam width (see
Figure 3).

b) Extended discontinuity:

Echodynamic pattern 2 and/or dimension greater than the −6 dB width (see Figure 4).

c) Isolated discontinuities:

The distance d, between points corresponding to the maxima of the indications of adjacent
discontinuities exceeds 40 mm (see Figure 5).

d) Grouped discontinuities:

The distance d, between points corresponding to the maxima of the indications of adjacent
discontinuities is less than or equal to 40 mm (see Figure 6).

16
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

Key
1 Conventional outline of −6 dB discontinuity
Dp Width of beam at depth of discontinuity
L Conventional length of −6 dB discontinuity

Figure 3 — Point-like discontinuity

(L ≤ Dp)

Key
1 Conventional outline of −6 dB discontinuity
Dp Width of beam at depth of discontinuity
L Conventional length of −6 dB discontinuity

Figure 4 — Extended discontinuity

(L > Dp)

17
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Key
1 Conventional outline of −6 dB discontinuity
Dp Width of beam at depth of discontinuity
d Distance between two discontinuities
L Conventional length of −6 dB discontinuity

Figure 5 — Isolated discontinuities

(L ≤ Dp, d > 40 mm)

Key
1 Conventional outline of −6 dB discontinuity
Dp Width of beam at depth of discontinuity
d Distance between two discontinuities
L Conventional length of −6 dB discontinuity

Figure 6 — Grouped discontinuities

(L ≤ Dp, d ≤ 40 mm)

18
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

14 Recording levels and acceptance criteria

Several quality classes may be applied to a forging or to parts of a forging. The applicable quality
class(es) shall be agreed between the purchaser and supplier. Table 5 details recording levels and
acceptance criteria which shall be applied to three quality classes for normal-beam probes. Tables 6
and 7 detail recording levels and acceptance criteria which shall be applied for angle-beam probes.

Table 5 — Quality classes, recording levels and acceptance criteria for normal-beam probesa
Acceptance criteria for
Forging thickness Recording level Isolated discontinuities Extended or grouped
t deqb deq b discontinuities
mm mm mm deqb
mm
Quality class 1
t ≤ 75 >5 ≤8 ≤5
75 < t ≤ 250 >8 ≤ 11 ≤8
250 < t ≤ 400 > 14 ≤ 19 ≤ 14
Indication with a total loss of backwall echo. A total
Indication with a 80 % loss of backwall echo shall be considered when its
t > 400 reduction of backwall amplitude becomes less that 5 % of its initial value
echo measured near the indication or less than or equal to
grass
Quality class 2
t ≤ 75 >3 ≤5 ≤3
75 < t ≤ 250 >5 ≤8 ≤5
250 < t ≤ 400 >8 ≤ 11 ≤8
400 < t ≤ 600 > 11 ≤ 15 ≤ 11
Indication with a total loss of backwall echo. A total
Indication with a 80 % loss of backwall echo shall be considered when its
t > 600 reduction of backwall amplitude becomes less than 5 % of its initial value
echo measured near the indication or less than or equal to
grass
Quality class 3
t < 75 >2 ≤3 ≤2
75 < t ≤ 250 >3 ≤5 ≤3
250 < t ≤ 400 >5 ≤8 ≤5
400 < t ≤ 600 >8 ≤ 11 ≤8
Indication with a total loss of backwall echo. A total
Indication with a 80 % loss of backwall echo shall be considered when its
t > 600 reduction of backwall amplitude becomes less than 5 % of its initial value
echo measured near the indication or less than or equal to
grass
a Reflector diameter shall not be interpreted as representing the dimension of the discontinuity which caused the echo.
b deq = Equivalent diameter of flat-bottomed hole.

19
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Table 6 — Recording levels and acceptance criteria for angle-beam probes for DGS techniquea

Acceptance criteria for

Forging thickness Recording level
Isolated discontinuities Extended or grouped
t deqa
discontinuities
mm mm
deq mm deq mm
t ≤ 75 >3 ≤5 ≤3
75 < t ≤ 250 >5 ≤8 ≤5
250 < t ≤ 400b >8 ≤ 11 ≤8
a deq = Equivalent diameter of flat bottomed hole.
b For thicknesses > 400 mm testing shall be as agreed between purchaser and supplier.

Table 7 — Recording levels and acceptance criteria for angle-beam probes for DAC techniquea, b, c

Forging Nominal test Recording Acceptance criteria for

thickness frequency level
Isolated Extended or
t MHz % discontinuities grouped
discontinuities
%
mm
%
t ≤ 75 1 30 60 30
2 50 100 50
75 < t ≤ 250 1 50 100 50
2 100 200 100
250 < t ≤ 400 1 100 200 100
2 200 400 200
a Based on 3 mm diameter side-drilled holes.
b A DAC based on 3 mm diameter side drilled holes shall be constructed for each frequency of probe used.
c The indication amplitude in dB, relative to the DAC, is given in Annex B.

15 Sizing
Where the extent of a discontinuity is required to be evaluated, one or more of the following techniques,
as agreed between the purchaser and the supplier, shall be used. These techniques shall be carried out
in accordance with the requirements detailed in EN ISO 16827:
a) 6 dB-drop technique;

b) 20 dB-drop technique;

c) maximum amplitude technique.

20
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

16 Test report
All tests shall be the subject of a written report which shall include the following information as
minimum requirements:
a) name of supplier;

b) order number;

c) identification of forging(s) to be tested;

d) scope of the test: surface areas and applicable quality classes;

e) stage of manufacture at which ultrasonic test was performed;

f) surface condition;

g) equipment used (instrument, probes, calibration and reference blocks);

h) technique(s) used to set test sensitivity;

i) reference to this standard and, if applicable, reference to the written procedure used;

j) test results: location, classification and amplitude (in terms of FBH-equivalent diameter, or in
percent of SDH) of all discontinuities exceeding the appropriate recording level;

k) details of any restrictions to the required scanning coverage and if applicable the extent of the
(untested) near surface zone;

l) date of the test;

m) name, qualification, certification (if specified) and signature of the operator.

21
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Annex A
(informative)

Maximum testable depth for corresponding beam path range for

circumferential angle-beam scans

Figure A.1 and Table A.1 show the maximum testable depth M for circumferential angle-beam scans for
a given probe and beam path range D.

Key
1 reflector
D is the beam path range for normal incidence on a radial reflector
M is the maximum testable depth for a particular probe angle and outside radius R
R outside radius
X beam angle
Regarding X, M and D, see Table A.1 underneath.

Figure A.1 — Maximum testable depth and corresponding beam path range for circumferential
angle-beam scans

22
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

Table A.1 — Maximum testable depth and corresponding beam path range

Beam angle, X Maximum testable depth, M Beam path range, D

70° 0,06R 0,34R
60° 0,13R 0,50R
50° 0,24R 0,64R
45° 0,30R 0,70R
35° 0,42R 0,82R
NOTE The maximum testable depth and beam path range to this depth for radial reflectors are given
in terms of the outside radius R of the forging.

23
BS EN 10228-4:2016
EN 10228-4:2016 (E)

Annex B
(informative)

Amplitude of indication in dB relative to % DAC

As an alternative to constructing a DAC which is a percentage of the 3 mm diameter side-drilled hole

DAC (100 % DAC), the required recording /acceptance level may be achieved by constructing the 3 mm
DAC (100 % DAC) and adjusting the amplitude according to Table B.1.

Table B.1 — Amplitude of indication in dB relative to % DAC

DAC Amplitude of indication relative to DAC

% dB
25 −12
30 −10
50 −6
60 −4
100 0
200 +6
400 +12

24
 BS EN 10228-4:2016
EN 10228-4:2016 (E)

Annex C
(informative)

Significant technical changes to the version EN 10228-4:1999

Some significant technical changes to the previous version EN 10228-4:1999 are listed below:
a) Scope has been aligned with EN 10228-3;

b) updating of the normative references;

c) generally updating and alignment of the designations to the actual state of art;

d) new Table 1 concerning surface finish related to quality class;

e) statement in chapter 9 concerning stage of manufacture aligned with EN 10228-3;

f) method of production for the types 3b and 3c in Table 2 updated;

g) supplementary footnote c) in Table 4 concerning scanning coverage with angle-beam probes for
products of type 3c);

h) correlation between terms and Figures 1 and 2 have been updated in Clause 13;

i) Note in Table A.1 updated.

25
This page deliberately left blank
This page deliberately left blank
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

British Standards Institution (BSI)

BSI is the national body responsible for preparing British Standards and other
standards-related publications, information and services.
BSI is incorporated by Royal Charter. British Standards and other standardization
products are published by BSI Standards Limited.

About us Reproducing extracts

We bring together business, industry, government, consumers, innovators For permission to reproduce content from BSI publications contact the BSI
and others to shape their combined experience and expertise into standards Copyright & Licensing team.
-based solutions.
The knowledge embodied in our standards has been carefully assembled in Subscriptions
a dependable format and refined through our open consultation process. Our range of subscription services are designed to make using standards
Organizations of all sizes and across all sectors choose standards to help easier for you. For further information on our subscription products go to
them achieve their goals. bsigroup.com/subscriptions.
With British Standards Online (BSOL) you’ll have instant access to over 55,000
Information on standards British and adopted European and international standards from your desktop.
We can provide you with the knowledge that your organization needs It’s available 24/7 and is refreshed daily so you’ll always be up to date.
to succeed. Find out more about British Standards by visiting our website at You can keep in touch with standards developments and receive substantial
bsigroup.com/standards or contacting our Customer Services team or discounts on the purchase price of standards, both in single copy and subscription
Knowledge Centre. format, by becoming a BSI Subscribing Member.
PLUS is an updating service exclusive to BSI Subscribing Members. You will
Buying standards
automatically receive the latest hard copy of your standards when they’re
You can buy and download PDF versions of BSI publications, including British revised or replaced.
and adopted European and international standards, through our website at
To find out more about becoming a BSI Subscribing Member and the benefits
bsigroup.com/shop, where hard copies can also be purchased.
of membership, please visit bsigroup.com/shop.
If you need international and foreign standards from other Standards Development
With a Multi-User Network Licence (MUNL) you are able to host standards
Organizations, hard copies can be ordered from our Customer Services team.
publications on your intranet. Licences can cover as few or as many users as you
wish. With updates supplied as soon as they’re available, you can be sure your
Copyright in BSI publications
documentation is current. For further information, email [email protected].
All the content in BSI publications, including British Standards, is the property
of and copyrighted by BSI or some person or entity that owns copyright in the Revisions
information used (such as the international standardization bodies) and has
Our British Standards and other publications are updated by amendment or revision.
formally licensed such information to BSI for commercial publication and use.
We continually improve the quality of our products and services to benefit your
Save for the provisions below, you may not transfer, share or disseminate any
business. If you find an inaccuracy or ambiguity within a British Standard or other
portion of the standard to any other person. You may not adapt, distribute,
BSI publication please inform the Knowledge Centre.
commercially exploit, or publicly display the standard or any portion thereof in any
manner whatsoever without BSI’s prior written consent.
Useful Contacts
Storing and using standards Customer Services
Standards purchased in soft copy format: Tel: +44 345 086 9001
Email (orders): [email protected]
• A British Standard purchased in soft copy format is licensed to a sole named
user for personal or internal company use only. Email (enquiries): [email protected]

• The standard may be stored on more than 1 device provided that it is accessible Subscriptions
by the sole named user only and that only 1 copy is accessed at any one time. Tel: +44 345 086 9001
• A single paper copy may be printed for personal or internal company use only. Email: [email protected]

Standards purchased in hard copy format: Knowledge Centre

• A British Standard purchased in hard copy format is for personal or internal Tel: +44 20 8996 7004
company use only. Email: [email protected]
• It may not be further reproduced – in any format – to create an additional copy.
Copyright & Licensing
This includes scanning of the document.
Tel: +44 20 8996 7070
If you need more than 1 copy of the document, or if you wish to share the Email: [email protected]
document on an internal network, you can save money by choosing a subscription
product (see ‘Subscriptions’). BSI Group Headquarters
389 Chiswick High Road London W4 4AL UK