How To Configure Failover For Cisco Unified SIP Proxy

How to Configure Failover for Cisco Unified SIP
Proxy
Document ID: 116015
Contributed by Randy Yuan Wu, Cisco TAC Engineer.
Apr 02, 2013
Contents
Introduction
Prerequisites
Requirements
Components
Conventions
Create a Fault−Resistant Default Gateway
Option One DNS SRV
Option Two HSRP
Setup Basic Connectivity
Setup Router−Level Failover
Track the Interfaces
HSRP Configuration of Primary Router
HSRP Configuration of Secondary Router
Related Information
Introduction
This document discusses two options to use in order to configure redundancy (failover) for Cisco Unified SIP
Proxy.
Prerequisites
Requirements
Cisco recommends that you have knowledge of these topics:
• Hot Standby Router Protocol (HSRP)

• DNS
• Cisco Unified SIP Proxy (CUSP)
Components
The information in this document is based on the CUSP.
The information in this document was created from the devices in a specific lab environment. All of the
devices used in this document started with a cleared default) configuration. If your network is live, make sure
that you understand the potential impact of any command.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Create a Fault−Resistant Default Gateway

The ability to create a fault−resistant default gateway is a key feature that the Cisco Unified SIP Proxy
(CUSP) provides. There are two options you can use to achieve redundancy for CUSP. One is to use Domain
Name System Server DNS SRV; the other is to create a virtual server. Hot Standby Router Protocol (HSRP) is
the mechanism by which a virtual server can be created. The first part of this document briefly describes how
to implement DNS SRV. The rest and majority of this document describes how HSRP?s features can be
implemented in order to detect problems on either the Integrated Services Router (ISR) chassis or on the
CUSP service−module itself.
Option One DNS SRV

In this option, configure the upstream element (whichever element forwards calls to CUSP) to use DNS. If the
attempt to reach cusp1 fails, the upstream element queries for the next entry in DNS SRV and attempts to use
cusp2. DNS must be configured properly in order for this to work.
1. First, two DNS SRV (service) records must be created, one for each cusp. The record which points to
cusp1 has a higher priority.
2. Secondly, two DNS A (hostname) records must be created so that the destinations in the DNS SRV
records can be resolved. This example shows what the DNS server should contain in its records.
Option Two HSRP

This diagram provides a basic architecture of how to configure CUSP for HSRP. The left side is an upstream
SIP element, and the right side is the downstream SIP element. In between these elements is one virtual router
with an IP address of 192.168.20.7. Both the upstream and downstream elements lead SIP traffic towards
the IP address of the virtual router. Inside the virtual router are two actual routers: a primary and a secondary.
These two routers share this same virtual IP address, and their configurations are identical with two
exceptions. Therefore, the configurations given in this document are the same for both routers.
Note: HSRP configuration for two CUSPs in a single router has not been tested. It might be possible to take
this solution and expand it for multiple CUSPs, but it is not supported at this time.
Setup Basic Connectivity

First, setup connectivity between the router and the blade. Although this is covered in other documents, it is
redundantly discussed in this document as well. In this example, the primary router has an address of
192.168.20.80 and its CUSP has an address of 192.168.20.81.
interface GigabitEthernet0/1
ip address 192.168.20.80 255.255.252.0
!!
interface Integrated−Service−Engine1/0
ip unnumbered GigabitEthernet0/1
service−module ip address 192.168.20.81 255.255.252.0
service−module ip default−gateway 192.168.20.80
!!
ip route 192.168.20.81 255.255.255.255 Integrated−Service−Engine1/0
The secondary router has an address of 192.168.20.90 and its CUSP has an address of
192.168.20.81.
ip address 192.168.20.90 255.255.252.0
!!
!!
Setup Router−Level Failover

Next, router level failover must be configured. This involves designation of one of the routers as the primary
and the other as the secondary. There is a slight difference in the configuration of the two routers.
Here is the configuration for the Primary Router:
standby 0 ip 192.168.20.7
standby 0 priority 100
Here is the configuration for the Secondary Router:
standby 0 ip 192.168.20.7
Both routers have their standby IP addresses set to the virtual router; however, the primary router has a higher
priority than the secondary one. That means, while all other things are identical, the primary router is
considered active, and all SIP traffic goes thru the primary router and then to the CUSP on that router. The
secondary router is in standby and only takes over if the primary router goes down for any reason, such as a
power outage.
Track the Interfaces

HSRP also must be setup to detect a CUSP level failure. What happens if the CUSP in the primary router dies
for someone reason, but the router itself is unaffected? SIP traffic continues to be sent to the CUSP in the
primary router. The priority of the router must be changed based on the state of the CUSP located in each
router.
The way to do this is to setup an ICMP echo to the CUSP from each router. In this case, the echo is sent every
two (2) seconds, with a one (1) second timeout. The lower these values are, then the quicker the router can
detect that the CUSP is down. However, if the ICMP echo is set too low, this could result in false positives.
The last configuration line in this example begins the echo and sets it to occur forever.
Note: ICMP echoes cannot track the state of the SIP port. HSRP failover cannot be initiated if the problem is
at the port level. To reiterate; if the router fails, the other router takes over; if the pings for the IP Service
Level Agreements (SLA) fail, the other router takes over; if SIP port fails, this is not detected.
ip sla 1
icmp−echo 192.168.20.81
timeout 1000
frequency 2
!!
ip sla schedule 1 life forever start−time now
An object must be setup to track the state of that echo. The object number is 100 in this case. The interface
must be set to decrement the priority of the router by 20, if this object's status is down. This means if the
CUSP on the primary router goes inactive for some reason, its priority will drop from 100 to 80. Its priority is
then less than that of the secondary, which has a priority of 90. If standby 0 preempt is set, it forces the
secondary router to takeover for the primary, and then the SIP traffic goes to the secondary CUSP.
track 100 ip sla 1 reachability

!!
standby 0 track 100 decrement 20
standby 0 preempt
HSRP Configuration of Primary Router

ip sla 1
icmp−echo 192.168.20.81
timeout 1000
frequency 2
!!
!!
!!
ip address 192.168.20.80 255.255.252.0
standby 0 ip 192.168.20.7
standby 0 preempt
!!
!!
HSRP Configuration of Secondary Router

ip sla 1
icmp−echo 192.168.20.81
timeout 1000
frequency 2
!!
!!
!!
ip address 192.168.20.90 255.255.252.0
standby 0 ip 192.168.20.7
standby 0 preempt
!!
!!
Related Information
• Hot Standby Router Protocol (HSRP): Frequently Asked Questions
• Cisco Unified SIP Proxy Software
• Technical Support & Documentation − Cisco Systems
Updated: Apr 02, 2013 Document ID: 116015

How To Configure Failover For Cisco Unified SIP Proxy

Uploaded by

Copyright:

Available Formats

How To Configure Failover For Cisco Unified SIP Proxy

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How To Configure Failover For Cisco Unified SIP Proxy

Uploaded by

Copyright:

Available Formats

How to Configure Failover for Cisco Unified SIP

• Hot Standby Router Protocol (HSRP)

Create a Fault−Resistant Default Gateway

Option One DNS SRV

Option Two HSRP

Setup Basic Connectivity

Setup Router−Level Failover

Here is the configuration for the Primary Router:

Here is the configuration for the Secondary Router:

Track the Interfaces

track 100 ip sla 1 reachability

HSRP Configuration of Primary Router

HSRP Configuration of Secondary Router

Updated: Apr 02, 2013 Document ID: 116015

You might also like