Scribd Logo
Upload

Welcome to Scribd!

  • 109 views

    SAG - Carpentry NC II

    Uploaded by

    Francis D. Alvar
    The document contains self-assessment guides for carpentry qualifications and units of competency. It includes questions to test skills like installing wooden door jambs and window frames, laying out and erecting formwork, installing ceiling and wall frames, and fabricating and installing wooden cabinets. Candidates indicate whether they are able to complete each task by checking "yes" or "no" boxes. They agree for the assessment to only be used for professional development and accessed by assessors and supervisors.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    SAG - Carpentry NC II

    Uploaded by

    Francis D. Alvar
    109 views8 pages
    The document contains self-assessment guides for carpentry qualifications and units of competency. It includes questions to test skills like installing wooden door jambs and window frames, laying out and erecting formwork, installing ceiling and wall frames, and fabricating and installing wooden cabinets. Candidates indicate whether they are able to complete each task by checking "yes" or "no" boxes. They agree for the assessment to only be used for professional development and accessed by assessors and supervisors.

    Original Title

    SAG - Carpentry NC II doc.doc

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document contains self-assessment guides for carpentry qualifications and units of competency. It includes questions to test skills like installing wooden door jambs and window frames, laying out and erecting formwork, installing ceiling and wall frames, and fabricating and installing wooden cabinets. Candidates indicate whether they are able to complete each task by checking "yes" or "no" boxes. They agree for the assessment to only be used for professional development and accessed by assessors and supervisors.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    109 views8 pages

    SAG - Carpentry NC II

    Uploaded by

    Francis D. Alvar
    The document contains self-assessment guides for carpentry qualifications and units of competency. It includes questions to test skills like installing wooden door jambs and window frames, laying out and erecting formwork, installing ceiling and wall frames, and fabricating and installing wooden cabinets. Candidates indicate whether they are able to complete each task by checking "yes" or "no" boxes. They agree for the assessment to only be used for professional development and accessed by assessors and supervisors.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 8
    At a glance
    Powered by AI
    The document outlines the self-assessment guide for carpentry work. It describes the various competencies required of a carpenter and the steps to lay out lines, frames, stairs and trusses according to specifications.

    Personal protective equipment should be worn according to safety standards. Materials and tools should be inspected and prepared for the job. Work areas should be kept clean and hazards removed before, during and after work.

    Reference lines must be located from offset lines marked according to drawings. Required lines are then marked, squared and plumbed as per drawings. Subsequent markings are made as needed.

    TESDA-OP-QSO-02-F07

    Rev. No. 00 03/01/17

    Reference. No.

    SELF - ASSESSMENT GUIDE

    Qualification: CARPENTRY NC II

     Layout reference lines


     Fabricate, install and remove wooden formworks
    Unit of  Install wooden door jamb, window frame and panels
     Install ceiling and wall frames and panels
    Competency
     Fabricate and Install wooden stairs
    covered:
     Install wooden floor supports and panels
     Fabricate and install roofing system
     Fabricate and install wooden cabinet
    Instruction:
     Read each of the questions in the left-hand column of the chart.
     Place a tick in the appropriate box opposite each question to indicate your answer.
    Can I? YES NO

    Prepare materials and hand tools *

     Use personal protective equipment (PPE) in accordance with


    Rule 1080 of Occupational Safety and Health Standards
     Select, inspect and prepare materials and hand tools consistent
    with job requirements
    Locate offset line established by the line and grade/ surveyor *

     Follow related sketches and working drawings according to job


    requirements
     Locate and verify offset line/ building line

    Establish required reference line *

     Mark initial lines from offset lines in accordance with working


    drawings.
     Mark, square and plumb final reference lines in accordance with
    working drawings
     Place subsequent markings as required

    Lay-out and cut dimension of form sheathings and stiffeners *

     Measure and mark form sheathings and stiffeners according to


    job specifications.
     Lay out and cut form sheathings and stiffeners according to
    required dimensions.
    CONCAR218-0719 ver. 1.00 1

    Carpentry NC II
    Assemble and erect form panels and components *

     Position and fix sheathings to stiffeners


     Check assembled form panels for squareness,
    levelness, plumbness and alignment.
     Position and fix primary and secondary supports to
    hold assembled form panels as per drawings.
     Check assembled form panels for compliance with job
    requirements.
    Layout location *
     Marks exact location for door and window opening based on
    working drawing
     Checks clearance of opening based on working drawings

    Fix door jamb and panels *


     Select and check assembled jamb and panels for compliance
    with job requirements
     Temporarily position jamb to hold assembled panels as per
    drawings.
     Check installed jamb and panels for squareness, levelness,
    plumbness and alignment
     Position and fix jamb and panels to openings
    Layout ceiling elevation, wall location and position of
    framing system*
     Mark exact layout for ceiling and wall frames based on working
    drawings
    Fix frames and panels*

     Install frames based on specifications


     Check installed frames for squareness, levelness, plumbness
    and alignment.
     Fix panels to frames based on working drawings

    Layout location and stair elevation *


     Mark exact location of stairs including riser and thread based on
    working drawings
    Place wooden stringer, thread, handrails and baluster *
     Cut and fabricate wooden stringers based on working drawing
    and/or actual requirements
     Position and fix wooden stringer and thread based on
    working drawings.

    CONCAR218-0719 ver. 1.00 2


    Carpentry NC II
     Check wooden stairs assembly for stability and firmness.

    Layout truss location and elevation *


     Mark exact location for roof truss assembly based on working
    drawing
    Place wooden roof truss assembly, purlins and fascia board *
     Position and fix wooden roof truss assembly according to
    job requirements
     Check alignment of all installed wooden roof truss assembly
    based on job requirements
     Install purlins as per required spacing

    Perform Housekeeping *
     Recovers and stockpile materials such as excess/un-used
    materials according to company rules and procedures
     Cleans and clears workplace of any obstructions and hazards
    before, during and after work
     Cleans tools, equipment and other materials after use

    I agree to undertake assessment in the knowledge that information gathered will


    only be used for professional development purposes and can only be accessed by
    concerned assessment personnel and my manager/supervisor
    Candidate’s Name & Signature Date

    CONCAR218-0719 ver. 1.00 3


    Carpentry NC II
    TESDA-OP-QSO-02-F07
    Rev. No. 00 03/01/17

    Reference. No.

    SELF - ASSESSMENT GUIDE

    Qualification: CARPENTRY NC II

    COC 1: FABRICATE, INSTALL AND REMOVE WOODEN FORMWORKS

    Instruction:
     Read each of the questions in the left-hand column of the chart.
     Place a tick in the appropriate box opposite each question to indicate your answer.

    Can I? YES NO

    Prepare materials and hand tools *


     Use personal protective equipment (PPE) in accordance with
    Rule 1080 of Occupational Safety and Health Standards
     Select, inspect and prepare materials and tools consistent
    with job requirements
    Lay-out and cut dimension of form sheathings and stiffeners*
     Measure and mark form sheathing and stiffeners according to
    job specifications.
     Lay out and cut form sheathing and stiffeners according to
    required dimensions.
    Assemble and erect form panels and components*
     Position and fix sheathings to stiffeners
     Check assembled form panels for squareness,
    levelness, plumbness and alignment.
     Position and fix primary and secondary supports to
    hold assembled form panels as per drawings.
     Check assembled form panels for compliance with job
    requirements.
    Clean and store reusable form panels and components*
     Recover and stockpile materials such as excess/un-used
    materials according to company rules and procedures
     Clean and clear workplace of any obstructions and hazards
    before, during and after work
     Clean tools, equipment and other materials after use
    I agree to undertake assessment in the knowledge that information gathered will
    only be used for professional development purposes and can only be accessed by
    concerned assessment personnel and my manager/supervisor
    Candidate’s Name and Signature Date

    NOTE: *Critical aspects of competency


    CONCAR218-0719 ver. 1.00 1

    Carpentry NC II
    TESDA-OP-QSO-02-F07
    Rev. No. 00 0/01/17

    Reference. No.

    SELF - ASSESSMENT GUIDE

    Qualification: CARPENTRY NC II

    COC 2: Install door and window assembly; install ceiling and wall
    system; and fabricate and install wooden cabinet
    Instruction:
     Read each of the questions in the left-hand column of the chart.
     Place a tick in the appropriate box opposite each question to indicate your answer.
    Can I? YES NO

    Prepare materials and hand tools*

     Use Personal protective equipment (PPE) in accordance with


    Rule 1080 of Occupational Safety and Health Standards
     Select, inspect and prepare materials and tools consistent with
    job requirements
    Locate offset line established by the line and grade/ surveyor*

     Follow related sketches and working drawings according to job


    requirements
     Locate and verify offset line/ building line

    Establish required reference line*

     Mark initial lines from offset lines in accordance with working


    drawings.
     Mark, square and plumb final reference lines in accordance with
    working drawings
     Places subsequent markings as required

    Fix door jamb and panels*

     Select and check door jamb assembly and panels for compliance
    with job requirements
     Temporarily position jamb to hold assembled panels as per
    drawings.

    CONCAR218-0719 ver. 1.00 2


    Carpentry NC II
     Check installed jamb and panels for squareness, levelness,
    plumbness and alignment
     Position and fix jamb and panels to openings
    Layout ceiling elevation, wall location and position of
    framing system*
     Mark exact layout for ceiling and wall frames based on working
    drawings
    Fix frames and panels*

     Install frames based on specifications


     Check installed frames for squareness, levelness, plumbness
    and alignment.
     Fix panels to frames based on working drawings

    Perform Housekeeping*
     Recover and stockpile materials such as excess/un-used
    materials according to company rules and procedures
     Clean and clear workplace of any obstructions and hazards
    before, during and after work
     Clean tools, equipment and other materials after use

    I agree to undertake assessment in the knowledge that information gathered will


    only be used for professional development purposes and can only be accessed by
    concerned assessment personnel and my manager/supervisor
    Candidate’s Name and Signature Date

    NOTE: *Critical aspects of competency

    CONCAR218-0719 ver. 1.00 3


    Carpentry NC II
    TESDA-OP-QSO-02-F07
    Rev. No. 00 0/01/17

    Reference. No.

    SELF - ASSESSMENT GUIDE

    Qualification: CARPENTRY NC II

    COC 3: Fabricate and Install Stair, Floor System and Truss assembly

    Instruction:
     Read each of the questions in the left-hand column of the chart.
     Place a tick in the appropriate box opposite each question to indicate your answer.
    Can I? YES NO

    Prepare materials and hand tools*

     Use personal protective equipment (PPE) in accordance with


    Rule 1080 of Occupational Safety and Health Standards
     Select, inspect and prepare materials and hand tools consistent
    with job requirements
    Layout truss location and elevation*

     Mark exact location for roof truss assembly based on working


    drawing
    Place wooden roof truss assembly and purlins *

     Position and fix wooden roof truss assembly according to job


    requirements
     Check alignment of all installed wooden roof truss assembly
    based on job requirements
     Install purlins as per required spacing

    Layout location and stair elevation*

     Mark exact location of stairs including riser and thread based on


    working drawings
    Place wooden stringer, thread, handrails and baluster *

     Cut and fabricate wooden stringers based on working drawing and/or


    actual requirements
     Position and fix wooden stringer and thread based on working
    drawings.
     Check wooden stairs assembly for stability and firmness.

    CONCAR218-0719 ver. 1.00 4


    Carpentry NC II
    Perform Housekeeping*
     Recover and stockpile materials such as excess/un-used
    materials according to company rules and procedures
     Clean and clear workplace of any obstructions and hazards
    before, during and after work
     Clean tools, equipment and other materials after use

    I agree to undertake assessment in the knowledge that information gathered will


    only be used for professional development purposes and can only be accessed by
    concerned assessment personnel and my manager/supervisor
    Candidate’s Name and Signature Date

    NOTE: *Critical aspects of competency

    CONCAR218-0719 ver. 1.00 5


    Carpentry NC II

    You might also like