04 ESRVCC Issue Troubleshooting Based On SEQ Platform - New

eSRVCC Issue Troubleshooting Based on SEQ Platform Document Security
eSRVCC Issue Troubleshooting Based on SEQ Platform
1、Purpose:
1） Through this exercise to understand the signaling plane optimization
ideas；
2） Through this exercise to master the method of eSRVCC problem
troubleshooting (identification and finding root cause) by SEQ
platform.
2、Excise arrangement:
1） Teacher explains the excise：10Min
2） Finish all the questions in this excise and output the related analysis
results for each group:70Min(Including 10Min break)
3） Share the analysis results for each group:30Min
4） Teacher comments and explain the answer:10Min
3、Excise preparation:
1） VoLTE signaling plane optimization ideas（explained by teacher）
How to troubleshooting the issue of eSRVCC handover failure?
A)Filter the TOP N cell by the KPI(from U2000)
（Or filtering the TOP N cell from SEQ directly. and because the
different statistic between SEQ and U2000, the TOP N cell is different
from SEQ and U2000. We should find out the TOP N cells that are in the
U2000 and SEQ to analyze the TOPN cells.
B)From U2000 KPI, we should get TOP N cell’s Handover out KPI between
two different cells. We can check whether all the failure happened in
some cell handovers to some dedicated cells and the failure is in
preparation phase or in execution phase.
C)Check the SEQ record for the TOP N cells(checking the failure reason,
handover target cell, abnormal NE information and so on to identify the
failure reason).
2020-5-19 HUAWEI confidential Page 1/6
information, unauthorized
diffusion prohibited
D)Check the neighbor cell configuration in eNodeB. If the demarcation
result is EPC or IMS side issue, we can think maybe the radio side is
no problem and to push the EPC or IMS to continue the troubleshooting.
E)Final solution(avoid the eSRVCC handover)
Check the TOP N cell’s these three counter: L.IntraFreHO.NoNRT,
L.InterFreHO.NoNRT, L.InterRATHO.NoNRT（for example,unpacking the
original performance in the eNodeB Brd log by FMA tool）.if the value
of these counters of TOP N cell are big, the meaning is the handover
happened with no neighbor cell too much times, we should optimize the
neighbor cell configuration. The normal handover priority is intra-
frequency handover is the highest and then the inter-frequency and the
inter-RAT(eSRVCC) is the lowest. Optimizing the the intra-frequency or
inter-frequency neighbor cell relationship can avoid some unnecessary
inter-RAT handover(eSRVCC) and then improve the eSRVCC handover success
rate indirectly. On the other hand, optimizing the LTE coverage can
also avoid some unnecessary eSRVCC handover(the eSRVCC happen rate
baseline for CMCC is not more than 5%).
2） eSRVCC failure classification
eSRVCC handover procedure can be divided two phases: handover preparation
phase and handover execution phase. The handover preparation phase is from
eNodeB sending measurement configuration to eNodeB sending handover command
to UE. The handover execution phase is from eNodeB sending handover command
to UE and UE received the handover command to UE complete to access the
GSM/UMTS handover target cell.
eSRVCC Handover preparation phase success rate(%)=times of eSRVCC handover
execution/times of eSRVCC handover attempt*100%
eSRVCC Handover execution phase success rate(%)=times of eSRVCC handover
success/times of eSRVCC handover execution*100%

eSRVCC Handover success rate(%)=times of eSRVCC handover success/times of
eSRVCC handover attempt*100%
Reference only!
(SCC AS(Service Centralization and Continuity Application Server)
4、Excise
Taking some project eSRVCC failure case, practice based on the U2000 KPI
statistics TOP cell and SEQ record to identify the issue. And find out the root cause
by referring to the cell configuration, engineering parameter and other basic
information and finally gives optimization recommendations.
1、 Excise point 1：
Q1：Some Cell eSRVCC KPI from radio side U2000 is shown as following:
Finish following table answer based on above table data:
eSRVCC handover eSRVCC handover preparation eSRVCC handover execution

success rate(%) phase success rate(%) phase success rate(%)
A：( ) A：( ) A：( )
Conclusion：Did eSRVCC handover failure happen in preparation phase or execution phase
for this cell?
A：
Q2：Handover KPI between two different cells from U2000:
From above table, what is the LAC and CI of the target cell that failed to
handover? Did the handover failure is preparation phase or execution phase?
A:
2、 Excise point 2:
The related SEQ record that eSRVCC handover failure is shown as following
file:
Tudicun4-2-SCD
HLS3HM 2PX-D3 SEQ Record（ eSRVCC HO Failure） .zip

Q1：Where is the SEQ record abnormal point and what is the recorded
failure? Please give the screenshot to show it.
A:
Q2：what is the failure reason recorded in the SEQ?
A:
Q3：Please find out the handover target cell(LAC and CI).
A：
Q4：Please accord to following 4G eNodeB configuration, find out the 2G

target cell information(LAC,CI,NCC,BCC,BCCH) which is the eSRVCC handover
failure target cell.
GERAN External
and neighbor cell relationship configuration.xlsx
BCCH
LAC CI NCC BCC
Frequency
Q5：eSRVCC handover to 2G is about like this procedure: 4G eNodeB needs

configure 2G cell of MCC, MNC,LAC, BCCH,NCC and BCC as its external cell, and
in the external neighbor cell relationship it also needs configure the
MCC,MNC,LAC and CI. UE will measure the 2G cell to report BCCH frequency,
PLMN, MCC,MNC,BCC and NCC.4G eNodeB sends eSRVCC handover required to MME
according its own configuration of external cell and external neighbor cell
relationship with the LAC and CI.

So we should check the 2G engineering parameter firstly. Please filter the

related 2G cell record from the following table according to the Q4.
GSM Engineering
Parameter.xlsx
A:
Q6：Please answer where is the issue according to the above filtering 2G

engineering parameter and how to optimize?
A：


04 ESRVCC Issue Troubleshooting Based On SEQ Platform - New

Uploaded by

Copyright:

Available Formats

04 ESRVCC Issue Troubleshooting Based On SEQ Platform - New

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

04 ESRVCC Issue Troubleshooting Based On SEQ Platform - New

Uploaded by

Copyright:

Available Formats

eSRVCC Issue Troubleshooting Based on SEQ Platform Document Security

eSRVCC Issue Troubleshooting Based on SEQ Platform

1） Through this exercise to understand the signaling plane optimization

2） Through this exercise to master the method of eSRVCC problem

troubleshooting (identification and finding root cause) by SEQ

1） Teacher explains the excise：10Min

results for each group:70Min(Including 10Min break)

3） Share the analysis results for each group:30Min

4） Teacher comments and explain the answer:10Min

1） VoLTE signaling plane optimization ideas（explained by teacher）

How to troubleshooting the issue of eSRVCC handover failure?

A)Filter the TOP N cell by the KPI(from U2000)

U2000 and SEQ to analyze the TOPN cells.

some cell handovers to some dedicated cells and the failure is in

preparation phase or in execution phase.

handover target cell, abnormal NE information and so on to identify the

D)Check the neighbor cell configuration in eNodeB. If the demarcation

no problem and to push the EPC or IMS to continue the troubleshooting.

E)Final solution(avoid the eSRVCC handover)

Check the TOP N cell’s these three counter: L.IntraFreHO.NoNRT,

L.InterFreHO.NoNRT, L.InterRATHO.NoNRT（for example,unpacking the

neighbor cell configuration. The normal handover priority is intra-

inter-RAT(eSRVCC) is the lowest. Optimizing the the intra-frequency or

inter-frequency neighbor cell relationship can avoid some unnecessary

inter-RAT handover(eSRVCC) and then improve the eSRVCC handover success

also avoid some unnecessary eSRVCC handover(the eSRVCC happen rate

baseline for CMCC is not more than 5%).

2） eSRVCC failure classification

eSRVCC handover procedure can be divided two phases: handover preparation

eNodeB sending measurement configuration to eNodeB sending handover command

to UE and UE received the handover command to UE complete to access the

GSM/UMTS handover target cell.

eSRVCC Handover preparation phase success rate(%)=times of eSRVCC handover

execution/times of eSRVCC handover attempt*100%

eSRVCC Handover execution phase success rate(%)=times of eSRVCC handover

success/times of eSRVCC handover execution*100%

2020-5-19 HUAWEI confidential Page 2/6

eSRVCC Handover success rate(%)=times of eSRVCC handover success/times of

eSRVCC handover attempt*100%

(SCC AS(Service Centralization and Continuity Application Server)

by referring to the cell configuration, engineering parameter and other basic

information and finally gives optimization recommendations.

Finish following table answer based on above table data:

eSRVCC handover eSRVCC handover preparation eSRVCC handover execution

2020-5-19 HUAWEI confidential Page 3/6

success rate(%) phase success rate(%) phase success rate(%)

A：( ) A：( ) A：( )

Conclusion：Did eSRVCC handover failure happen in preparation phase or execution phase

for this cell?

Q2：Handover KPI between two different cells from U2000:

2020-5-19 HUAWEI confidential Page 4/6

Q2：what is the failure reason recorded in the SEQ?

Q3：Please find out the handover target cell(LAC and CI).

Q4：Please accord to following 4G eNodeB configuration, find out the 2G

Q5：eSRVCC handover to 2G is about like this procedure: 4G eNodeB needs

2020-5-19 HUAWEI confidential Page 5/6

So we should check the 2G engineering parameter firstly. Please filter the

Q6：Please answer where is the issue according to the above filtering 2G