For DENSO Authorized

ECD Service Dealer Only

Diesel lnjection pump

fN".+o3{r-l

SERVICE MANUAL
Gommon Rail System for ISUZU
6HK1/6SD1 Type Engine
Operation
June, 2003

DENSO CORPORATION 0040001.8

GENERAL
The common rail system was designed for electronic control of injection
quantity, injection tim-
ing and injection pressure to obtain optimal operational control.

Features
' Lower exhaust gas and higher output due to high pressure injection in all usage ranges.
' Reduction in noise and exhaust gas due to injection rate control.
' lmproved performance due to increased flexibility in the injection timing setting.
' lndependent control of injection pressure in response to engine speed and
load.

Main Elements

Cylinder Total
Manufacturer Vehicle Model Engine Model Displacement
Configuration
(cc)
6HK1 7,900
ISUZU Fonarard 65D1 Straight 6 9,900
6WG1 15,600

* Dweo vocYo
rw2u aIWJ'" ."8*p
((trt+er+) \fl*,p DBnsa c&sc,^)
< /,i,r/tr
1. Outline
1.1 System Outline
This system also provides the following functions:
., A self-dia$nbSiS and dlarm function using computer to diagnose the system's major
.' icoriiponents'ind alert the driver in the event of a problem.
' . A'faii-iafe function to stop the engine, depending upon the location of the problem.
. A backup function to change the fuel regulation method, thus enabling the vehicle to
continue operation.
1.2 System Gonfiguration
Divided by function, the system can be classified according to the fuel system and the control
system.
[1] Fuel System
High-pressure fuel that is generated by the supply pump is distributed to the cylinders using a
rail. Electromagnetic valves in the injectors then open and close the nozzle needle valve to con-
trol the start and end of fuel injection.

Solenoid valve to control

the needle lift

Fuel tank Supply pump lnjector

[2] Gontrol System

Based on the signals received from various sensors mounted on the engine and the vehicle,
the ECU controls current timing and the duration in which the current is applied to the injectors,
thus ensuring an optimal amount of fuel is injected at an optimal time.
The control system can be broadly classified according to the following electronic components:
sensors, computers, and actuators.

Computers Aciuators
(Accelerator opening)
lnjectors

NE sensor
(Engine speed) /Fuel injection quantity \

(Crankshaft position sensor) \and injection timing control eic./

/ Cylinder \
\recognition signal /

(Fuel oressure control)

' Q000081E
[3] System Gonfiguration (1)

Signals from I
switches t

THW THL

Pressure limiter

Fuel filiter
TDC sensor
NE sensor
[4] System Gonfiguration (2)

o
o
O
E
o
I
po
o
.g

HHH
o_
--E E
(L
=0)
U'
a 5
U)

I .Y6
I c0
Ilo qtc/)
I o(J
OA
Il-|-oaI
\o.r-
'15 0
.c9
o
C >c) @
o OU) c
C
0) =IAo C.)
a
o (L o: 0)
E 93 f
f o 6c (D
o rn (D
o -;@ o
c)
E
o- att
occ.,
o
=oJ
6f F
0)

E <a O(g
C^
=o .E
o o
6 n LF q)
c c
rA) 0) -c) o-
o
6ut a G,
oO
E 0) - E

4s
u.r
f
a
+3,i
o
+3 c)
(L
s5 o <2
OU) od)
'60?
)
c0 cc) OLU.
c)
u8 p
to) o
<o- .g

c
.o
(o
z .o
U
=E O-
Y7t :E E
o)
o
.E
goo
a"
E
o =^
oo
1\ O \J
F.o
YOd)
€o)=
;r6
0)
d =<
^c= dJ,
oc
-8
(EYz
Xtro
=.=6 dJ a'l aa
Atrr:.
e- 0)
Eco5^c) = @!

ooo 'o) 6qoF

ooo C
Oi^CI
oo0) Lto)(J
LU \xcLll
5-- 5-- S_- +r+rli
1.3 Construction and Operation of the System
The rail system is comprised of a supply pump, a rail, and injectors, and also includes an ECU
and sensors to regulate those components.
The supply pump generates the internalfuel pressure in the rail. Fuel pressure is regulated by
the quantity of fuel discharged by the supply pump. ln turn, the fuel discharge quantity is regu-
lated by electronic signals from the ECU that turn the PCVs (pump controlvalves) ON and OFF,
Upon receiving fuel pressurized by the supply pump, the rail distributes the fuelto the cylinders.
The pressurized fuel is detected by the rail pressure sensor (installed in the rail) and undergoes
feedback control so that actual pressure will match the command pressure (designated accord-
ing to the engine speed and load).
Pressurized fuel in the rail passes through the injection pipes that lead to the cylinders, and applies
pressure to the injector nozzles and the control chamber'
The injector regulates injection quantity and timing by turning the T\AA/ (two-way valve) ON and OFF.
When the T\AA/ is ON (current applied), the fuel circuit switches over, causing the high-pressure
fuel in the control chamber to flow out via the orifice. As a result, the force of the high-pressure
fuel at the nozzle valve opening causes the needle valve to lift, thus starting the injection of fuel.
When the T\AA/ is turned OFF (current not applied), the fuel circuit switches over so that high-
pressure fuel, traveling via the orifice, is introduced to the control chamber. As a result, the nee-
dle valve lowers, thus ending the injection of fuel'
Thus, through electronic control, the timing of the current applied to the T\AA/ determines the
injection timing, and the duration in which current is applied to the T\ ru determines the injection
quantity.

. lnjection quantity control

TWV control ' lnjection timing conirol
Additional information . lnjection rate controi
(temperature, pressure)

Engine load

sl,.g/tL
%l-s !/
Supply Pump

lnjector
1.4 Comparison to Conventional Pump

lnline Type Common Rail System

lnstantaneous high
System Consiant high
pressure

lnjection quantity
regulation Pump (governor) ECU, injector (TWV)
lnjection timing
Pump (timer) ECU, injector (TWV)
reoulation
Distribution of
qenerated pressure Pump Supply pump

Distribution Pump Rail

lnjection pressure
(Dependent on engine speed and injection volume) Supply pump (PCV)
regulation
[3] Operation
A: The PCV remains open during the plunger's downward stroke, allowing low-pressure fuelto
be drawn into the plunger chamber by way of the PCV.
B: lf the valve remains open because current is not applied to the PCV, even after the plunger
begins its upward stroke, the fuel that was drawn in returns via the PCV, without being pres-
surized.
C: When current is applied to the PCV in order to close the valve at the timing that accommo-
dates the required discharge volume, the return passage closes, causing pressure in the
plunger chamber to rise. The fuel then passes through the delivery valve (check valve) to the
rail. As a result, an amount of fuel that corresponding to the plunger lift after the PCV closes
becomes the discharge volume, and varying the timing of the PCV closure (plunger pre-
stroke) varies the discharge volume, thus regulating rail pressure.
A': After surpassing the maximum cam lift, the plunger begins its downward stroke, causing
pressure in the plunger chamber to decrease. At this time, the delivery valve closes, thus
stopping the pumping of the fuel. ln addition, because current to the PCV valve is cut off, the
PCV opens, allowing low-pressure fuel to be drawn into the plunger chamber. Thus, the
pump assumes condition "A".

scharge ,16z 1g_61

Suction process Delivery process lUrTl€ Q=.- 4

Cam lifl TTr'

Pre-stroke
Valve open €
PCV Valve
operation closed
/lncreasrngy'
operation V
dischargevolume
,,/ Discharging required
{rcino discharce voIrme volume
[4] PGV (pump control valve)
The PCV regulates the volume of fuel discharged by the supply pump in order to regulate rail
pressure. The volume of fuel discharged by the supply pump to the rail is determined by the
time at which current is applied to the PCV.

[5] Trochoid TYPe Feed PumP

The feed pump, which is housed in the supply pump, draws fuel up from the tank and delivers
it to the chamber via the fuel filter. The feed pump rotor is driven by the camshaft.
The rotation of the camshaft causes the outer and inner rotors to rotate. At this time, the suction
port side pump chamber volume (the space surrounded by the outer and inner rotors) increases
gradually, causing the fuel entering from the fuel inlet to be drawn into the pump chamber via
ine suction port. Along with the rotation of the rotor, the fuel that has been drawn in moves to-
wards the discharge port and is discharged. The discharged fueltravels via the fuel outlet and
is fed into the suPPlY PumP bodY.
Volume decreased
(while discharging fuel to discharge port)

Outer rotor To pump chamber

.>
lnner rotor

-\N
l/ V

Suction
port

I
From fuel tank
Volume increased
(while drawing in flel)

[6] Coupling
The coupling is an intermediary device that transmits Coupling
the engine driving torque to the supply pump camshaft'
2.2 Common Rail
[1] Gonstruction
The functionof the rail is to distribute the high-pressure
fuel pressurized by the supply pump to each cylinder
injector.
The rail pressure sensor, flow damper, and pressure
limiter are mounted on the rail.
A fuel injection pipe is attached to the flow damper to
deliver high-pressure fuel to the injector.
The pressure limiter piping is routed back to the fuel tank'

[2] Flow Damper

The flow damper reduces pressure pulsation in the l5toppeil
high-pressure pipe, thus delivering fuel to the injectors
at a stable pressure. Furthermore, in the event an ex-
cessive flow of fuel, the flow damper shuts off the fuel
passage, thus preventing the abnormal fuel flow.
lDurilltdamerngl
When abnormal amount of fuel flows the high-pres-
sure is applied to the piston. As shown in the illustra-
tion, this causes the piston and ballto move right, until
the ball reaches the seat and closes the fuel passage.
During abnormal flow such as
excessive injection volume

[3] Pressure Limiter

The function of the pressure limiter is to dispel abnormally
high pressure by opening its valve to release pressure' (L lPc
The pressure limiter operates (opens the valve) when
rail pressure reaches approximately 140MPa.
Then, when the pressure decreases to approximately
30MPa, the pressure limiter resumes (closes the valve)
its function to maintain pressure.

NOTE:
Do not attempt to remove or to reinstall the flow damper, pressure limiter, or rail pressure
sensor.
[4] Rail Pressure Sensor
The rail, the rail pressure sensor is mounted on the rail and detects the fuel pressure. lt is a
semi-conductor type of pressure sensor that utilizes the properties of silicon to change its elec-
trical resistance when pressure is applied.

VPC 5
ECU
34
o
tl)
gJ
E
E2
f
o1
50 100 150

Pressure PC (MPa)

2.3 lnjector
[1] Outline
The function of the injector is to inject high-pressure fuel from the rail into the engine combus-
tion chamber at the proper timing, quantity, ratio, and atomization, in accordance with signals
from the ECU.
The T\AA/ (two-way solenoid valve) regulates pressure in the control chamber in order to control
the beginning and end of injection'
The orifice restrains the opening speed of the nozzle valve to regulate the injection ratio.
The command piston transmits pressure from the control chamber to the nozzle needle valve.
The nozzle atomizes the fuel.

Start of lnjection (TWV ON) End of lnjection (TWV OFF)

10
[2] Gonstruction
The injector consists of the nozzle portion (similar to that of the conventional type), the orifice
(which regulates the injection ratio), the command piston, and the two-way solenoid valve
(rvw).

Orifice 2

Orifice 1

Command piston

Lower body

Guide bushing

Washer

Spring

Pressure pin

Tip packing

11
[3] Operation
The T\AA/ portion of the injector consists of two valves, an inner valve (fixed) and an outer valve
(movable). Both valves are precision-fitted on the same axis. The valves respectively form inner
and outer seats, and either of the seats opens selectively depending upon whether the T\AA/ is
ON or OFF.
a. No lnjection
\Mren no current is applied to the solenoid, the valve spring and hydraulic pressure forces
push the outer valve downward, causing the outer seat to remain closed. Because the rail
high pressure is applied to the control chamber via the orifices, the nozzle remains closed
without injecting fuel.
b. Begin lnjection
When current is applied to the T\ ru, the solenoid force pulls the outer valve upward, causing
the outer seat to open.
As a result,'fuel from the control chamber flows out via the orifice, causing the needle to lift
and to start fuel injection. Furthermore, the injection ratio increases gradually in accordance
with the movement of the orifice. As the application of current continues to apply, the injector
reaches its maximum injection ratio.
c. End lnjection
When current to the T\ A/ is cut off, the valve spring and hydraulic force (fuel pressure) cause
the outer valve to descend and the outer seat closes. At this time, high-pressure fuel from the
rail is immediately introduced into the control chamber, causing the nozzle to close suddenly.
As a result, injection ends swiftly.

lnner valve

Outer valve

Outer seat

Orifice 2

Orifice 1

Rail
(constant high pressure)

18-130 MPa

No lnjection End lnjection

Q000098E

12
[4] Gircuit Diagram

2WV #1 (1st cylinder)

2WV #4 (6th cylinder)

2WV #6 (4th cylinder)

WARNING:
High voltage is applied to the wires connected to COMMON1, COMMON2, and the T\Atu
#1+6 terminals of the ECU. Exercise extreme caution to prevent electric shock.

13
2.4 Sensors and Relays
t1] NE Sensor (crankshaft position sensor)
When the signal holes on the flywheel move past the
sensor, the magnetic line of force passing through the
coil changes, generating alternating voltage'
The signal holes are located on the flywheelat 7.5-degree
intervals. There are a total of 45 holes, with holes missing
in three places. Therefore, every two revolutions of the
engine outputs 90 pulses.
This signal is used to detect the engine speed and the
crankshaft position in 7.S-degree intervals.
t2l TDC sensor (cylinder recognition sensor)
Similar to the NE sensor, the sensor utilizes the alternating
voltage generated by the changes in the magnetic line of
TDC (cylinder recognition) sensor
force passing through the coil.
The disc-shaped gear located in the center of the supply
pump camshaft has a cog (U-shaped cutout) at 120-degree
intervals, plus one tooth in an additional location. Accord-
ingly, every two revolutions of the engine outputs seven
pulses. The combination of the NE pulse' TDC pulse is rec-
ognized as the No. 1 cylinder reference pulse' 00001 01 E

A combination of the NE pulse and the TDC pulses are

used for the cylinder reference pulse, and the irregular
pulse is used to determine the No. 1 cylinder' /+\
\i7
s)tlr?
Z{rs

No.6 cylinder TDC Pulse

120"cR 240"CR

Aux. NE Pulse #1|TDC #5iTDC #31 TDC

I
#6irDc #2irDc #4i
I

I
I
I
I

zs"cn
-s'cn i i
+
I
I 105'cR i

/-*",cytinder NE reference pulse No.6 cylinder NE reference pulse

14
[3! Water Temperature Sensor (THW made another
manufacturer)
The water temperature sensor detects the temperature
of the engine coolant water and outputs it to the ECU.
The sensor uses a thermistor, which varies resistance
according to temperature. As the ECU applies voltage
to the thermistor, it uses a voltage resulting from the
division of the computer internal resistance and the
thermistor resistance to detect the temperature.
Q000104E

ECU VTHW 5

o)
o)
(u
=o
=
5
o

-40 -20 0 20 40 60 80 '100 120 THW

Coolant temperature ('C)
Q0001 05E

[4] Fuel Temperature Sensor (THL)

The fueltemperature sensor detects the fueltemperature and outputs it to the ECU. The sensor
uses a thermistor, which varies resistance according to temperature. As the ECU applies volt-
age to the thermistor, it uses a voltage resulting from the division of the computer internal re-
sistance and the thermistor resistance to detect the temperature.

ECU VTH L5
4
c)
o) ?
o
=o
2
o_
f
\J 1

0 -40 -20 0 20 40 60 B0 100 120 THL

Fuel temperature ('C)
o000'106E

15
[5] Accelerator Position Sensor
This sensor converts the angle of the pedal effort applied to the accelerator pedal into electrical
signals and sends them to the ECU. The accelerator sensor uses hall elements. A magnet is
mounted on the shaft that moves in unison with the accelerator pedal, and the magnetic field
orientation changes with the rotation of the shaft. The changes in the magnetic field orientation
generate voltage.

4.0

VAccpl 3.0
VAccp2
(v) 2.0
Magnets 1.0
(1 paiQ
0
50 100
Accelerator opening (%)
Accp

[6] ldle Set Button (made by another manufacturer)

A control knob is installed within reach of the driver,
enabling the driver to set the idle rpm. lt increases idle
rpm using the idle-up switch, and decreases idle rpm
to the normal rate using the idle-down switch.

[7] Main Relay

To supply current to the ECU, the main relay points close when current is applied to ihe main
relay coil.
[8] PCV Relay
The PCV relay supplies current to the supply pump PCV (discharge volume control valve).

16
3. Various Types of Gontrol
This system controls the fuel injection quantity and injection timing more optimally than the mechanical
governor or timer used in conventional injection pumps.
For system control, the ECU makes the necessary calculations based on signals received from
sensors located in the engine and on the vehicle in order to control the timing and duration in
which current is applied to the injectors, thus realizing optimal injection.

[1] Fuel lnjection Rate Gontrol Function

The fuel injection rate control function controls the ratio of the quantity of fuel that is injected
through the nozzle hole during a specified period.

[2] Fuel lnjection Quantity Gontrol Function

The fuel injection quantity control function, replaces the conventional governor function, and
controls fuel injection to achieve an optimal injection quantity based on the engine speed and
the accelerator opening.

[3] Fuel lnjection Timing Control Function

The fuel injection timing control function, replaces the conventional timer function, and controls
the fuel injection to achieve an optimal injection timing according to the engine speed and the
injection quantity.

[4] Fuel lnjection Pressure Control Function (Rail Pressure Control Function)
The fuel injection pressure control function (rail pressure control function) uses a rail pressure
sensor to measure fuel pressure, and feeds this data to the ECU to control the pump discharge
quantity.
Pressure feedback control is implemented to match the optimal quantity (command quantity)
set according to the engine speed and the fuel injection quantity.

lnput signal Control output

Fuel injection rate control

Fuel injection quantity control

Fuel control computer

(ECU) Fuel injection timing control

Fuel injection pressure control

Various sensors
.Goolant temperature sensor
.Fuel temperature sensor Atmospheric air
'Atmospheric air temperature pressure sensor
sensor etc.

17
3.1 Fuel lnjection Rate Control
[1] Main lnjection
Same as conventional fuel injection.
[2] Pilot lnjection
Pilot injection is the injection of a small amount of fuel
prior to the main injection.
While the adoption of higher pressure fuel injection is
associated with an increase in the injection rate, the
lag (injection lag) that occurs from the time fuel is in-
jected until combustion starts cannot be reduced be-
low a certain value. As a result, the quantity of fuel
injected before ignition increases, resulting in explosive combustion together with ignition, and
an increase in the amount of NOx and noise. Therefore, by providing a pilot injection, the initial
injection rate is kept to the minimum required level dampening, the explosive first-period com-
bustion and reducing NOx emissions.
TDC

Delta injection

Smallinj
prior to i,

TLr lmprovement

Large pre-mixture
combustion
(NOx, noise)

lgnition delay
Q000111 E

[3] Split lnjection

V/hen the rotation is low at starting time, a small
amount of fuel is injected several times prior to main
injection.

o000112E

'18
4. Reference
4.1 Diagnosis Gode
Diagnosis
Failure Mode Diagnosis Light Pattern
Code
NE sensor system B (Light for 20 seconds at 700rpm or less) '15

Aux. NE sensor system B 14

Rail abnormal high pressure (Sensors' failure) A (constantly lit up) 245
Rail pressure sensor output is abnormally
A 115
constantly
Railabnormal pressure (overcharged by supply
A 151
pump)
Rail abnormal pressure (control system) A '118

lnjection quantity adjustment resistor A 34

Coolant tem perature sensor C (not lighting) 23
Fuel temperature sensor c 211
Atmospheric air temperature sensor c 22
Accelerator sensor 1 A 24
Accelerator sensor 2 A 24
Accelerator sensor A 28
Atmospheric air pressure sensor c 71

Starter S/W c 417

#1'.261
#2:262
#3" 263
Flow damper c
#4:264
#5:265
#6:266
#1 271
#2 272
#3 273
T\AA/ driving circuit open A
#4 274
#5 275
#6 276
Common lsystem
158
T\AA/ driving circuit short (+B) A
Common 2system
159
Common lsystem
158
T\AA/ driving circuit short (GND) A Common 2system
l(o
Supply pump does not send pressurized fuel to
A z16
rail, or pressure limiter operates
Supply pump does not send necessary
A 227
pressurized fuel due to fuel leakage
PCV system short (+B) PCV1. 217
A
(Coil or harness) PCV2"218
PCV system open/short (GND) PCVl 247
A
(Coil or harness) PCV2 248
A AE
Abnormal A,/D convension
ECU A
PCV and relay system A 421

19
 Diagnosis
Failure Mode Diagnosis Light Pattern
Code
Main relay B 416
Boost pressure sensor c 32
A:42
Abnormally high boost pressure c B'.32
Abnormally low boost pressure c 65

Overrunl (Software) c
Overrun2 (Hardware) c 543

Abnormal output by accelerator sensorl A 24

Abnormal output by accelerator sensor2 A 24

Abnormal watch dog timer A 35

Charge circuit failure A 35

20
4.2 Circuit Diagram
"ON" Relay

STA/SW PCV1
PCV,l
KEY/SW PCV2
PCV2
DIAG-L
, Diagnosis S/W
DG/SW
+
COMMONl
coMl\,4oNl
+BP COMN.4ON2
+BP COMMON2

vr-xtrL TWVI
Main Relay TWVl
TW,i2
_1_,,, TWV2
TWV3
GND TWV3
GND TWV4
P.GND TWV4
P.GND TWVs
TWV5
TW^/6

Crank Position Sensor

NE+ TWV6

(NE Sensor) NE.

NE_SLD AT-REL

G+
Cylinder Recognition S"nso, 1
(TDC Sensor) )
Exhaust Break
Relay
17084
EXB-REL
J'1708B EXB/SW

ACC'1-VCC

ldle-up S,&V
Accl rDLUP/sw

ACCl-GND TDLDWN/SW
ldle-down SM

Transmission SM

Neutral S/W

lnjection Quantity Clutch S/1/V

Adjustment Resistor
FQ-GND rt
NrcLR/sw Memory Clear S/W
Atmospheric Air
THA
Temperature Sensor
Fuel Temperature THF
MF AM/SIG
f
'.-J rr
rrAMisrc
Sensor
MFAM/USE AM/usE

Coolant Temperature
Sensor
THV

TH-GND
I
PFUEL-VCC
Rail Pressure PFUEL
Sensor PFUEL
PFUEL-GND

A-VCC
Boost Pressure PBOOST CHECKER
Sensor A-GND
TACHO

Case GND

21