International Journal of Mechanical and Production

Engineering Research and Development (IJMPERD)

ISSN(P): 2249–6890; ISSN(E): 2249–8001
Vol. 10, Issue 2, Feb 2020, 201–212
© TJPRC Pvt. Ltd.

TWO WHEELED VEHICLES E20 FUEL MAGNETIZATION STUDY ON EXHAUST

GAS EMISSIONS

T. H NUFUS1, S. L. KUSUMASTUTI2, A. ULFIANA3, N. HIDAYATI4, E. RIDWAN5,

A. SULISTYOWATI6, M. H. TULLAH7, I. NURISKASARI8, C. S. ABADI9
1,3,4,5,6,7,8,9
Lecturer, Department of Mechanical Engineering, Politeknik Negeri Jakarta, Prof. Dr. G.A Siwabessy Street,
West Java, Indonesia
2
Electrical Engineering Politeknik Negeri Jakarta, Prof. Dr. G.A Siwabessy Street,
West Java, Indonesia
ABSTRACT

Research on the magnetization of fossil fuels that can improve the quality of combustion has been done but
magnetization for fossil and non-fossil fuel mixtures such as bioethanol and gasoline mixtures has not been done.
Therefore, this study aimed to analyze the effect of magnetizing the mixture of gasoline (premium) and bioethanol
related to the quality of combustion, especially exhaust emissions on two-wheeled vehicles (motorcycles) as 4-stroke with

Original Article
125 cc engine capacity. During the experiments, CO, NOx and SO2 as the gas emissions were measured using a
NOVA2000 Gas analyzer. The composition of the fuel used is E20. This fuel has flowed through electromagnetic fields
with a strength of 647.15 Gauss, 847.25 Gauss, 1068.29 Gauss, and 1419.57 Gauss. Our study showed that when the
mixture of fossilized fuel–bioethanol is magnetized, the resulted exhaust emission of CO, NOx, and SO2 will be
plummeted by 48%, 68%, and 76%. Moreover, the combustion energy increased by 0.641%. Henceforth, this study
improved previous papers such as Faris et al. [1] and Patel et al.[2] that used a magnetic field strength greater than 2000
Gauss, also Jain & Deshmukh [3] employed a magnetic field strength less than 2000 Gauss.

KEYWORDS: Magnetization, Bioethanol, Gasoline & Exhaust Emissions

Received: Jan 28, 2020; Accepted: Feb 18, 2020; Published: Feb 26, 2020; Paper Id.: IJMPERDAPR202018

NOMENCLATURE

E20 (80% Premium and 20% Bioethanol)

CO Carbon Monoxide

NOx Nitrogen Oxide

SO2 Sulfur Dioxide

INTRODUCTION

The use of gasoline engines for transportation purposes is increasing. The situation is not following government
policy in the energy sector, which seeks to use petroleum fuel as economically as possible, considering that
petroleum is a non-renewable energy source. Later on, this unsustainable demand will cause an energy crisis. This
energy crisis caused people to change their mindset to further intensify research and use from non-renewable energy
to renewable energy.

www.tjprc.org SCOPUS Indexed Journal [email protected]

202 T. H Nufus, S. L. Kusumastuti, A. Ulfiana, N. Hidayati, E. Ridwan,
A. Sulistyowati, M. H. Tullah, I. Nuriskasari, C. S. Abadi

The increasing demand for gasoline engines for transportation has contributed partly to the energy crisis recently.
Not only because of the decrease of oil reserves gradually, but also oil's inability to renew its source. Thus, to reside with
the government policy in the energy sector, petroleum fuel must be utilized economically. Later on, the energy crisis has
taught society to switch from non-renewable energy to renewable energy.

Meanwhile, the motor vehicle exhaust gas mission has become the main source of air pollution, especially in
urban areas. Although motor vehicle exhaust gases consist of non-hazardous compounds such as nitrogen, carbon dioxide,
and water vapor, it also contains a large number of other compounds that can endanger the health as well as the
environment. Contaminants contained in motor vehicle exhaust gases are carbon monoxide (CO), various hydrocarbon
compounds, various oxides of nitrogen (NOx) and sulfur (SOx). The exhaust gas is released into the air due to evaporation
from the fuel system [4][5].

In the spirit of appreciating the renewable energy, we want to design an environmentally friendly energy pulse. In
this particular experiment, we choose ethanol or bioethanol. Based on the above, we need an environmentally friendly
energy pulse, one of which is ethanol or bioethanol. Bioethanol cannot be 100% used as a substitute for fossil fuels. In
order to use on gasoline engines, this bioethanol must be mixed with fossil fuels. In this research, the fuel used is E20 (20%
bioethanol + 80% premium). This fuel flows through a magnetic field as a fuel saver. Many papers already studied the
effect of magnetization on exhaust gas emission using fossil fuel [1] [2] but none of them studied the effect of
magnetization on exhaust gas emission using mixed fuel, especially E20 fuel. Therefore the purpose of this study is to
analyze the effect of E20 fuel magnetization towards its exhaust gas emission on two wheels vehicle.

The hypothesis we investigated is the fossil fuels mixed with bioethanol and which are flowed through magnetic
fields will be able to improve engine performance, which is indicated by decreasing levels of exhaust emissions and
increasing combustion energy. Therefore, the purpose of this study is to analyze the fuel magnetization of gasoline engine
performance.

BACKGROUND

The effect of magnetic fields on fuel consumption and exhaust emissions on a 1-cylinder 4-stroke engine has been
discussed in the literature. Faris et al. [1] reported that the addition of the magnetic field intensity to the fuel increased the
infrared absorption. Therefore, the greater magnet intensity applied to the fuel, the more vibration experienced by CH
atomic microstructure. This condition will create more space to oxidize with oxygen and create greater energy attraction
between CH atoms. After the fuel was magnetized with a magnetic field intensity of 2000-9000 Gauss, the fuel
consumption will decrease by 9-14% and exhaust emissions of HC and CO will decrease by 30% and 40%. This research
used permanent magnets, even though this permanent magnet will decrease its magnetic field strength due to vibration and
heat. This condition could be improved had we utilised the electromagnetic field because the strength of the field will
remain constant as long as the current existed.

Jain and Deshmukh [3] conducted a study of MFC (Magnetic Fuel Conditioner) with a strength of 1000-1800
Gauss on a 5 HP diesel engine with variations in load, this magnetic effect caused a change in fuel molecules from cluster
to de-cluster. They claimed to decrease the fuel consumption by 10-30% and decrease the exhaust emissions of HC, CO,
and NOx by 40%. The advantage of this research is that the magnetic field used is relatively small but the results obtained
such as fuel consumption are relatively large compared to the Faris et al. [1], while the exhaust emissions are the same as

Impact Factor (JCC): 8.8746 SCOPUS Indexed Journal NAAS Rating: 3.11
Two Wheeled Vehicles E20 Fuel Magnetization Study on Exhaust Gas Emissions 203

those obtained by Faris et al. [1]. The weaknesses of this study are the same as Faris et al.[1], which uses permanent
magnet.

Patel et al. [2] conducted a study on the use of magnetic fields derived from a mixture of ceramics and iron oxide
which produced an intensity of 2000 Gauss magnetic fields on a 4-stroke 1 cylinder engine. Patel explained that the
cluster-de cluster effect caused fuel consumption to decrease by 8% and the exhaust emissions of HC and NOx decreased
by 30% and 27% respectively after the fuel was magnetized with a magnetic field intensity of 2000 Gauss. Patel's research
only uses permanent magnets which change over time as a result of friction, vibration and high temperatures [2]. The study
used a magnetic field strength greater than 2000 Gauss, while the reduction in fuel consumption and exhaust gas emissions
was the same as Jain & Deshmukh [3] reported, the excess magnets used were made from a mixture of ceramics and iron
oxide that had not been studied by other researchers.

Most researchers use permanent magnets with a magnetic field strength greater than 2000 Gauss, as well as using
fossil fuel engines. Our study will lead to use electromagnets (non-permanent) with a magnetic field strength of less than
2000 Gauss and the engine uses a mixture of fossil fuels and biofuels. This magnet was placed between the fuel tank and
injector as shown in Figure 1, the fuel that passes through the magnet for the initial stage was left for 20 minutes, meaning
that the fuel molecules change from clusters to de clusters so that when mixing with air molecules in the combustion
chamber it was easier reacting with air. The presence of this magnet does not interfere with other devices [5].

Figure 1: The Position of Magnets on two-wheeled Vehicle

Engines.

The choice of E20 in this study as fuel for two-wheeled vehicles, because the composition of E20 is the maximum
limit for two-wheeled vehicles that do not need to be renovated. [6]. The short-term research target was to analyze what is
the maximum percent decrease in exhaust emission levels due to the influence of magnets on fuel. while the long term is to
produce two-wheeled vehicles that were environmentally friendly so that it can reduce air pollution in areas where most
residents use two-wheeled vehicles. From this research, it is expected that by using a small magnetic field strength and a
strong magnetic field, there will be a reduction in exhaust emission levels greater than an engine that uses fossil fuels.

MATERIALS AND METHODS

www.tjprc.org SCOPUS Indexed Journal [email protected]

204 T. H Nufus, S. L. Kusumastuti, A. Ulfiana, N. Hidayati, E. Ridwan,
A. Sulistyowati, M. H. Tullah, I. Nuriskasari, C. S. Abadi

The method is carried out experimentally, the data is obtained by direct observation and measurement in the field with the
available measuring instruments. Experimental results data are used for analysis and later on, we will answer the
objectives. Based on the research objective, the fuel needed is a mixture of gasoline (premium) and bioethanol (cassava)
with a composition of the mixture is E20 (20% bioethanol and 80% gasoline), the two types of fuel are each obtained from
PT Pertamina and PT WATS both has fulfilled the SNI standard (Indonesian National Standard). Furthermore, the strength
of the magnetic electromagnet fields used is 647.15 Gauss, 847.25 Gauss, 1068.29 Gauss, and 1419.57 Gauss. The given
magnetic field strength ranges between 500-1500 Gauss. Based on observations, the magnetic field strength of 500 Gauss
is the minimum magnetic limit which affects the fuel. Less than that value, the fuel is not affected. While the value is
approximately 1500 Gauss, the maximum limit of this study to compare with previous researchers who used a magnetic
field strength greater than 2000 Gauss.

Table 1: Property Gasoline & Ethanol [6]

Property Gasoline Ethanol
C-fraction [mass %] 87.4 52.2
O-fraction [mass %] 0 34.7
Density [kg /m3] 750-760 785-810
Stoichiometric air / fuel ratio 14.2- 15.0 9.0
Kinematic viscosity [mm2/s] 0.5 1.3
Vapor pressure (RVP) [kPa] 53-60 17
Research octane number (RON) [-] 91-100 110
Lower heating value [MJ / kg] 44.0 27.0
Latent heat vaporization [kJ / kg] 380-400 910

The tools used in this study include the Yamaha Mio Motor in 2018, a 4-cylinder cylinder with 125cc combustion
chamber, Teslameter model MG-801 for measuring magnetic field strength, NOVA 2000 gas analyzer to test exhaust
emissions (CO, NO, NOx and SO2) and tachometer measure engine speed. The test is carried out in various rotation, 1000
rpm, 1500 rpm, and 2000 rpm.

The procedure of conducting research is shown in Figure 2. The study begins by calibrating the equipment
needed, examining gasoline engine components such as lubricating oil, lubricating oil filter, fuel filter, diesel engine speed
measured by a digital tachometer. In the exhaust mounted gas analyzer to observe the effects of the exhaust gas. The test
begins with starting the engine at 1000 rpm and then held for ± 10 minutes to get the normal working temperature of the
engine. After the machine operates normally, data retrieval starts. The independent variable is bioethanol E20 magnetized
for 20 minutes [7] with variations in intensity or magnetic strength of 647.15 Gauss, 847.25 Gauss, 1068.29 Gauss, and
1419.57 Gauss, while the dependent variable in this study is the exhaust gas emissions and the heating value of the fuel,
each data retrieval is repeated 5 times.

Data from the study were compared between fuels before and after magnetization and were then processed
quantitatively in the form of several graphs, namely graphs of emissions levels of CO, NO, NOx and SO2 on rotation and
magnetic strength. The results of data analysis in the form of graphs then analyzed again by referring to several reference
journals listed in the bibliography.

Impact Factor (JCC): 8.8746 SCOPUS Indexed Journal NAAS Rating: 3.11
Two Wheeled Vehicles E20 Fuel Magnetization Study on Exhaust Gas Emissions 205

Figure 2: Diagram of the Research.

RESULTS AND DISCUSSIONS

Emission Exhaust gas is the residual combustion of fuel in the internal combustion engine, an external combustion engine,
a jet engine that is released through the engine exhaust system. Some of the gases contained in exhaust emissions are CO
(carbon monoxide), NOx (nitrogen oxides), and SO2 (sulfides). Each of these gases has its respective dangers at certain
levels [8].

Carbon Monoxide (CO)

Carbon monoxide (CO) is a substance that is colorless, odorless and has no taste. CO in the form of gases occurs at
temperatures above 1920C. This substance weights 96.5% by weight of water and is not soluble in water. Carbon monoxide
contained in nature is formed through several processes, including [9][10].

• Availability of insufficient oxygen during the combustion process to convert all carbon to CO2

• The reaction between carbon dioxide and components containing carbon at high temperatures.

Figure 3 presents a graph of the relationship between CO levels in each electromagnetic field strength variation to engine
speed.

Figure 3: The Effect of Engine Speed on CO Emission at different Magnetization Fuel

www.tjprc.org SCOPUS Indexed Journal [email protected]

206 T. H Nufus, S. L. Kusumastuti, A. Ulfiana, N. Hidayati, E. Ridwan,
A. Sulistyowati, M. H. Tullah, I. Nuriskasari, C. S. Abadi

In Figure 3, it explains that CO levels at 1000 rpm are higher than those at 1500 rpm and 2000 rpm. High levels of
CO at 1500 engine speeds are possible because at low rotations the ignition angle tends to reverse, resulting in late
combustion. The element contained in the fuel will ignite through combustion produced by spark plugs. Late combustion
causes elements C and O not change to CO2 which causes high CO emissions. CO levels decrease in the 2000 to 2500
rounds, this can be caused by the rotation when the ignition is more advanced and the combustion is not too late so that
makes combustion better.

On the other hand Figure 2, also shows that fuel magnetization can reduce CO exhaust gas levels, the greater the
electromagnetic field given to the fuel flow in a gasoline engine, the CO levels will decrease. This is due to the magnetized
fuel molecule resulting in increased vibrations of the fuel molecule as a result of the attraction between small molecules,
reduced fuel grain diameter and decreased viscosity and polarity of the fuel molecule approaching the air molecules so that
the mixture of air and fuel becomes more homogeneous. Resulting in more complete combustion [7]. This complete
combustion results in decreased CO exhaust emissions. CO gas emission decreases the most occurs in fuels through the
electromagnetic field strength of 1419.57 Gauss and 2000 rpm engine speed, CO levels decrease by about 58%

Nitrogen Oxide (NOx)

Nitrogen oxide (NOx) is a gas found in the atmosphere consisting of gases nitric oxide and nitrogen dioxide. Nitrogen
oxide is a colorless and odorless gas, whereas nitrogen dioxide has a reddish-brown color and a sharp odor. The formation
of NOx in the combustion system occurs at high temperatures. Most of the NOx made by humans come from burning
charcoal, oil, natural gas, and gasoline [11][12].

Figure 4: The Effect of Engine Speed on NOx Emission at different

Magnetization Fuel.

Figure 4 shows a graph of the relationship between NOx exhaust emissions and various variations in the
electromagnetic field strength. NOx exhaust emissions decreased with a increase of engine rotation. Nitrogen is relatively
inert, so to act directly with air is rather difficult, but there are several causes of NOx emissions, including the high
concentration of oxygen contained in the fuel plus the high temperature of the combustion chamber. Also, a pile of carbon
crust in the combustion chamber will also increase engine compression and can cause hot spots that can increase NOx
levels. Machines that frequently detonate will also cause high NOx concentrations.

The other side of figure 4, also shows that fuel magnetization can reduce NOx exhaust gas levels, the greater the
electromagnetic field given to the fuel flow in a gasoline engine, the NOx level decreases. The cause is the same as in the
CO explanation, which includes magnetized fuel which increases the polarity of the fuel molecule so that it approaches the

Impact Factor (JCC): 8.8746 SCOPUS Indexed Journal NAAS Rating: 3.11
Two Wheeled Vehicles E20 Fuel Magnetization Study on Exhaust Gas Emissions 207

air molecule, resulting in a more homogeneous mixture of air and fuel resulting in more complete combustion. These
results in decreased NOx exhaust emissions. The greatest decrease in NOx gas emissions occurs in fuels through the
electromagnetic field strength of 1419.57 Gauss and 2000 rpm engine speed, NOx levels decrease by approximately 68%

Sulfur

Oxide Pollution by sulfur oxides is mainly caused by two colorless gas components, namely sulfur dioxide (SO2)
and sulfur trioxide (SO3), and both are referred to as SOx. Only one-third of the amount of sulfur oxide present in the
atmosphere is the result of human activities. Transportation is not the main source of SOx pollutants, but combustion of
fuel at its source is the main source of SOx pollutants, for example burning oil, gas, and wood [13][14].

Figure 5: The Effect of Engine Speed on SO2 Emission at different Magnetization Fuel.

Figure 5 shows a graph of the relationship between SO2 exhaust emissions and various variations in the
electromagnetic field strength. The vertical axis represents the level of SO2 (ppm) and the horizontal axis represents the
engine speed. Theoretically, the use of bioethanol as a mixture of engine fuel will reduce SO2, because bioethanol derived
from plant oils is almost free of sulfur content so that the addition of bioethanol into fuel will be able to reduce the sulfur
content in the fuel itself. High levels of SO2 at 1500 rpm engine speed are possible because at low rotations the ignition
angle tends to reverse, resulting in late combustion. The element contained in the fuel will ignite through combustion
produced by spark plugs. SO2 levels decrease in 2000 to 2500 rounds, this can be due to the rotation when the ignition is
more advanced and combustion is not too late so that makes combustion better. The SO2 gas emissions' greatest decrease
of around 76% occurs in fuels through the electromagnetic field strength of 1419.57 Gauss and 2000 rpm engine speed.

Figure 6 presents a graph of the relationship between combustion energy and electromagnetic field strength. It
appears that the greater the magnetic field gives the greater the energy.

www.tjprc.org SCOPUS Indexed Journal [email protected]

208 T. H Nufus, S. L. Kusumastuti, A. Ulfiana, N. Hidayati, E. Ridwan,
A. Sulistyowati, M. H. Tullah, I. Nuriskasari, C. S. Abadi

Figure 6: The Effect of Magnetic Fields at Fuel Energy.

Magnetic field strengths affect combustion energy, meaning that a lot of fuel that is burned or combusted occurs
more completely. This data supports the results of emissions testing.

CONCLUSIONS

The magnetization of the E20 fuel causes;

• The greater the magnetic field strength applied to the fuel and the greater the engine speed, the smaller the level of
exhaust emissions. CO exhaust emissions decreased by 48%, NOx decreased by 6% and SO2 decreased by 76%.

• The greater the magnetic field strength applied to the fuel the smaller the combustion energy. Combustion energy
increased 0.641%, this shows that combustion that occurs is more perfect.

From all the above, it has been proven that magnets can improve the quality of exhaust emissions, and the strength of a
magnetic field of 647.15 Gauss can affect fuel molecules. The weakness of this research is the amount of time the magnetic field
exposure to the fuel is 20 minutes, to overcome this time, the dimensions of the galvanum pipe are made according to the rate of fuel
that is sprayed into the combustion chamber.

REFERENCES

1. Faris, A. S., Al-Naseri, S. K., Jamal, N., Isse, R., Abed, M., Fouad, Z., Kazim, A., Reheem, N., Chaloob, A., Mohammad, H.,
Jasim, H., Sadeq, J., Salim, A. and Abas, A. (2012) ‘Effects of magnetic field on fuel consumption and exhaust emissions in
two-stroke engine’, Energy Procedia, 18, pp. 327–338. doi: 10.1016/j.egypro.2012.05.044.

2. Patel, P. M., Rathod, G. P. and Patel, T. M. (2014) ‘Effect of magnetic field on performance and emission of single cylinder
four stroke diesel engine’, IOSR Journal of Engineering, 4(5), pp. 28–34.

3. Jayasinghe, C., & Perera, T. Dispersion Model For Tvoc Emissions From Solvent-Based Paints.

4. Jain, S. and Deshmukh, P. S. (2012) ‘Experimental Investigation of Magnetic Fuel Conditioner ( M . F . C ) in I . C . engine’,
IOSJR JournL OF engineering, 2(7), pp. 27–31.

5. Baena, L. M., Gómez, M. and Calderón, J. A. (2012) ‘Aggressiveness of a 20 % bioethanol – 80 % gasoline mixture on
autoparts : I behavior of metallic materials and evaluation of their electrochemical properties’, Fuel. Elsevier Ltd, 95, pp.
320–328. doi: 10.1016/j.fuel.2011.12.002.

Impact Factor (JCC): 8.8746 SCOPUS Indexed Journal NAAS Rating: 3.11
Two Wheeled Vehicles E20 Fuel Magnetization Study on Exhaust Gas Emissions 209

6. Nufus, T. H., Praeko, R., Setiawan, A. and Hermawan, W. (2017) ‘Characterization of biodiesel fuel and its blend after
electromagnetic exposure’, Cogent Engineering. Cogent, 75, pp. 1–12. doi: 10.1080/23311916.2017.1362839.

7. Corro, G. and Ayala, E. (2008) ‘Bioethanol and diesel / bioethanol blends emissions abatement’, Fuel, 87, pp. 3537–3542.
doi: 10.1016/j.fuel.2008.07.014.

8. Iodice, P., Senatore, A., Langella, G., Amoresano, A., Industriale, I. and Federico, N. (2017) ‘Advantages of Ethanol –
Gasoline Blends as Fuel Substitute for Last Generation Si Engines’, 0(0), pp. 1–7. doi: 10.1002/ep.

9. Chhalotre, S., Baredar, P. V., & Soni, S. Investigation Of The Effects Of Gasoline–Ethanol Fuel Blend On Throttle Response
And Intake Air Temperature In A Naturally Aspirated Si Engine.

10. Kemal, M., Sayin, C. and Canakci, M. (2014) ‘The effect of different alcohol fuels on the performance , emission and
combustion characteristics of a gasoline engine’, Fuel. Elsevier Ltd, 115, pp. 901–906. doi: 10.1016/j.fuel.2012.09.020.

11. Clairotte, M., Adam, T. W., Zardini, A. A., Manfredi, U., Martini, G., Krasenbrink, A., Vicet, A., Tournié, E. and Astorga, C.
(2020) ‘Effects of low temperature on the cold start gaseous emissions from light duty vehicles fuelled by ethanol-blended
gasoline’, Applied Energy. Elsevier Ltd, 102(2013), pp. 44–54. doi: 10.1016/j.apenergy.2012.08.010.

12. Ghadikolaei, M. A. (2016) ‘Effect of alcohol blend and fumigation on regulated and unregulated emissions of IC engines — A
review’, Renewable and Sustainable Energy Reviews. Elsevier, 57, pp. 1440–1495. doi: 10.1016/j.rser.2015.12.128.

13. Mustafa Koc, Yakup Sekmen, Tolga Topgu, H. S. Y. (2009) ‘The effects of ethanol – unleaded gasoline blends on engine
performance and exhaust emissions in a spark-ignition engine’, Renewable Energy, 34, pp. 2101–2106. doi:
10.1016/j.renene.2009.01.018.

14. Chhalotre, S., Baredar, P. V., & Soni, S. Investigation Of The Effects Of Gasoline–Ethanol Fuel Blend On Throttle Response
And Intake Air Temperature In A Naturally Aspirated Si Engine.

15. Prati, M. V., Costagliola, M. A., Tommasino, C., Della, L. and Meccariello, G. (2014) ‘Road grade influence on the exhaust
emissions of a scooter fuelled with bioethanol / gasoline blends’, 3(July), pp. 790–799. doi: 10.1016/j.trpro.2014.10.059.

16. Wiratmaja, I. G. (2010) ‘Pengujian Karakteristik Fisika Biogasoline Sebagai Bahan Bakar Alternatif Pengganti Bensin
Murni’, Cakra M, 4(2).

17. Yu, F. and Yu, B. (2004) ‘The use of ethanol – gasoline blend as a fuel in an SI engine’, Renewble Energy.29, pp. 1181–1191.
doi: 10.1016/j.renene.2003.11.012.

AUTHOR’S PROFILE

Tatun Hayatun Nufusis a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta, Indonesia.
Her researchinterest is energy saving, and has conducted a series of experiment on fuel magnetisasion and renewable
energy.

www.tjprc.org SCOPUS Indexed Journal [email protected]

210 T. H Nufus, S. L. Kusumastuti, A. Ulfiana, N. Hidayati, E. Ridwan,
A. Sulistyowati, M. H. Tullah, I. Nuriskasari, C. S. Abadi

Sri Lestari Kusumastuti is a lecturer at the Department of Electrical Engineering, Politeknik Negeri Jakarta. Her
educational background is a electrical engineering. Her research interest is electromagnetic fields.

Andi Ulfiana received master‘s degree of Instrumentation Physics at Universitas Indonesia. She is a lecturer at the
Department of Mechanical Engineering, Politeknik Negeri Jakarta. She is interested in research about instrumentation and
simulation software.

Noor Hidayati is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. Her research interest
is renewable energy and has experienced as engineer at stated own company which focused in energy conservation.

Emir Ridwan is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. His educational
background is a Mechanical engineering. His research interest ismachine elemen

AriekSulistyowati is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. Her educational
background is a Physic. Her interest research in basic science.

Impact Factor (JCC): 8.8746 SCOPUS Indexed Journal NAAS Rating: 3.11
Two Wheeled Vehicles E20 Fuel Magnetization Study on Exhaust Gas Emissions 211

Muhammad HidayatTullah is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. His
educational background is a Industrial engineering. His research interest is outomotif

Isnanda Nuriskasari is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. Her
educational background is a chemical engineering. Her interest research in renewable energy and material for catalyst.

Cecep Slamet Abadi is a lecturer at the Department of Mechanical Engineering, Politeknik Negeri Jakarta. His
educational background is a Mechanical engineering. His research interest is renewable energy conversion and energy
storage.

www.tjprc.org SCOPUS Indexed Journal [email protected]