www.hilti.com.ph Profis Anchor 2.8.

3
Company: Page: 1
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

Specifier's comments:

1 Input data
Anchor type and diameter: HST3 M12 hef2
Effective embedment depth: hef = 70 mm, hnom = 80 mm
Material:
Evaluation Service Report: ETA-98/0001
Issued I Valid: 2/9/2018 | -
Proof: Design method ETAG (No. 001 Annex C/2010)
Stand-off installation: eb = 0 mm (no stand-off); t = 8 mm
Anchor plate: lx x ly x t = 150 mm x 450 mm x 8 mm; (Recommended plate thickness: not calculated
Profile: Flat bar; (L x W x T) = 30 mm x 5 mm
Base material: uncracked concrete, C25/30, fc,cube = 30.00 N/mm2; h = 300 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement

R
- The anchor calculation is based on a rigid anchor plate assumption.

Geometry [mm] & Loading [kN, kNm]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Profis Anchor 2.8.3
Company: Page: 2
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

2 Load case/Resulting anchor forces y

Load case: Design loads 2

Anchor reactions [kN]

Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 3.865 2.843 1.800 2.200
2 3.865 2.843 1.800 2.200 x
Tension

max. concrete compressive strain: - [‰]

max. concrete compressive stress: - [N/mm2]
resulting tension force in (x/y)=(0/0): 7.730 [kN]
resulting compression force in (x/y)=(0/0): 0.000 [kN]

Anchor forces are calculated based on the assumption of a rigid anchor plate. 1

3 Tension load (ETAG, Annex C, Section 5.2.2)

Load [kN] Capacity [kN] Utilization bN [%] Status
Steel Strength* 3.865 32.214 12 OK
Pullout Strength* 3.865 18.257 22 OK
Concrete Breakout Strength** 7.730 43.198 18 OK
Splitting failure** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (anchors in tension)

3.1 Steel Strength

NRk,s [kN] gM,s NRd,s [kN] NSd [kN]
45.100 1.400 32.214 3.865

3.2 Pullout Strength

NRk,p [kN] yc gM,p NRd,p [kN] NSd [kN]
25.000 1.095 1.500 18.257 3.865

3.3 Concrete Breakout Strength

Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm]
88,200 44,100 105 210
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 1.000 1.000
k1 N0Rk,c [kN] gM,c NRd,c [kN] NSd [kN]
10.100 32.399 1.500 43.198 7.730

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Profis Anchor 2.8.3
Company: Page: 3
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

4 Shear load (ETAG, Annex C, Section 5.2.3)

Load [kN] Capacity [kN] Utilization bV [%] Status
Steel Strength (without lever arm)* 2.843 28.320 11 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 5.685 120.092 5 OK
Concrete edge failure in direction x+** 5.685 62.180 10 OK
* anchor having the highest loading **anchor group (relevant anchors)

4.1 Steel Strength (without lever arm)

VRk,s [kN] gM,s VRd,s [kN] VSd [kN]
35.400 1.250 28.320 2.843

4.2 Pryout Strength

Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm] k-factor
88,200 44,100 105 210 2.780
ec1,V [mm] y ec1,N ec2,V [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 1.000 1.000
N0Rk,c [kN] gM,c,p VRd,cp [kN] VSd [kN]
32.399 1.500 120.092 5.685

4.3 Concrete edge failure in direction x+

lf [mm] dnom [mm] k1 a b
70 12.0 2.400 0.068 0.060
c1 [mm] Ac,V [mm2] A0c,V [mm2]
150 180,000 101,250
y s,V y h,V y a,V ec,V [mm] y ec,V y re,V
1.000 1.000 1.419 0 1.000 1.000
V0Rk,c [kN] gM,c VRd,c [kN] VSd [kN]
36.980 1.500 62.180 5.685

5 Combined tension and shear loads (ETAG, Annex C, Section 5.2.4)

bN bV a Utilization bN,V [%] Status

0.212 0.100 1.500 13 OK
baN + baV ≤ 1.0

6 Displacements (highest loaded anchor)

Short term loading:
NSk = 2.863 [kN] dN = 0.048 [mm]
VSk = 2.106 [kN] dV = 0.396 [mm]
dNV = 0.399 [mm]
Long term loading:
NSk = 2.863 [kN] dN = 0.096 [mm]
VSk = 2.106 [kN] dV = 0.584 [mm]
dNV = 0.592 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!

The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Profis Anchor 2.8.3
Company: Page: 4
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid anchor plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the anchor plate without creating air voids and before application of the loads.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Profis Anchor 2.8.3
Company: Page: 5
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

8 Installation data
Anchor plate, steel: - Anchor type and diameter: HST3 M12 hef2
Profile: Flat bar; (L x W x T) = 30 mm x 5 mm Installation torque: 0.060 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm
Plate thickness (input): 8 mm Hole depth in the base material: 90 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 140 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.

8.1 Recommended accessories

Drilling Cleaning Setting

• Suitable Rotary Hammer • Manual blow-out pump • Hilti SIW 22T-A impact screw driver
• Properly sized drill bit • Torque wrench
• Hammer
y

75 75
50

2
225
350

x
225

1
50

75 75

Coordinates Anchor [mm]

Anchor x y c-x c+x c-y c+y
1 0 -175 150 150 - -
2 0 175 150 150 - -

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com.ph Profis Anchor 2.8.3
Company: Page: 6
Specifier: Project: Woodlands CivicCentre
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 16/7/2019
E-Mail:

9 Remarks; Your Cooperation Duties

• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 HST3 (-R) subject to:
Anchor size M8 M10 M12 M16 M20 M24
Hammer drilling*

TE2(-A) – TE30(-A) TE40 – TE70

Diamond core drilling*

DD-30W, DD-EC1

Setting tool*
Setting tool HS-SC -

Hollow drill bit drilling*

- TE-CD, TE-YD

Seismic Set/ Filling Set**

Seismic/Filling Set M8-M20 (Carbon and Stainless Steel A4) -

*Installation methods provided in ETA-98/0001

**Seismic set needed to fill the annular gap between anchor and fixture:
No annular gap, double design resistance (agap=1)