See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/316430419

DESIGN AND CONSTRUCTION OF VERTICAL AXIS WIND TURBINE

Article · November 2014

CITATIONS READS

2 17,941

2 authors:

Piyush Gulve Dr. Shivprakash Bhagwatrao Barve

University of North Carolina at Charlotte MAEER`s MIT College of Engineering
3 PUBLICATIONS   2 CITATIONS    34 PUBLICATIONS   54 CITATIONS   

SEE PROFILE SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Augmentation of Distillate Output of Solar Still View project

Truck skid wear View project

All content following this page was uploaded by Dr. Shivprakash Bhagwatrao Barve on 24 April 2017.

The user has requested enhancement of the downloaded file.

International
INTERNATIONALJournal of Mechanical
JOURNALEngineeringOFand Technology (IJMET), ISSN
MECHANICAL 0976 – 6340(Print),
ENGINEERING
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME
AND TECHNOLOGY (IJMET)

ISSN 0976 – 6340 (Print)

ISSN 0976 – 6359 (Online)
IJMET
Volume 5, Issue 10, October (2014), pp. 148-155
© IAEME: www.iaeme.com/IJMET.asp
Journal Impact Factor (2014): 7.5377 (Calculated by GISI) ©IAEME
www.jifactor.com

DESIGN AND CONSTRUCTION OF VERTICAL AXIS

WIND TURBINE

Piyush Gulve, Dr. S.B.Barve

Department of Mechanical Engineering, MIT College of Engineering, Pune, India-411038.

ABSTRACT

The principle objective of this project is Rural Electrification via hybrid system which
includes wind and solar energy. Our intention is to design a wind turbine compact enough to be
installed on roof tops. So we decided to design a vertical axis wind turbine (VAWT) over Horizontal
Axis Wind Turbine (HAWT). Advantages of VAWT over HAWT are compact for same electricity
generation, less noise, easy for installation and maintenance and reacts to wind from all directions.
The wind turbine designed to generate electricity sufficient enough for a domestic use. The electricity
generated will be stored in the battery and then given to the load. This project emphasizes on
electrification of remote areas with minimum cost where load shading still has to be done to meet
with demand of urban areas.

Nomenclature

V- Air Velocity
A - Turbine Swept area
D - Rotor Diameter
h - Rotor Height
ρ - Air Density
KE - Kinetic Energy
ω - Angular Speed [rad/s],
R - Rotor Radius [m]
N - Number of Blades
c - Blade Chord
L - Blade length

148
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

1. INTRODUCTION

Wind power devices are used to produce electricity, and commonly termed wind turbines.
The orientation of the shaft and rotational axis determines the classification of the wind
turbines. A turbine with a shaft mounted horizontally parallel to the ground is known as a horizontal
axis wind turbine or (HAWT). A vertical axis wind turbine (VAWT) has its shaft normal to the
ground.[1]

Fig 1: Configurations for shaft and rotor orientation

The two configurations have instantly distinguishable rotor designs, each with its own
favorable characteristics. Vertical-axis wind turbines (VAWT) can be divided into two major groups:
those that use aerodynamic drag to extract power from the wind and those that use lift. The
advantages of the VAWTs are that they can accept the wind from any direction. This simplifies their
design and eliminates the problem imposed by gyroscopic forces on the rotor of a convectional
machine as the turbine tracks the wind. The vertical axis of rotation also permits mounting the
generator and drive train at ground level [2]. The disadvantages of this type of rotors is that it is quite
difficult to control power output by pitching the rotor blades, they are not self – starting and they
have low tip-speed ratio [3]. Horizontal – axis wind turbines (HAWT) are convectional wind turbines
and unlikely the VAWT are not omnidirectional. As the wind changes direction, HAWTs must
change direction with it. They must have some means for orienting the rotor with respect to the wind.

2. LITERATURE SURVEY

2.1 Theoretical Maximum Efficiency [1]

High rotor efficiency is desirable for increased wind energy extraction and should be
maximized within the limits of affordable production. Energy (P) carried by moving air is expressed
as a sum of its kinetic energy [Equation (1)]:

K E = ½ρAV3 (1)
Where,
V - Air Velocity
A – Turbine Swept area
ρ- Air Density

A physical limit exists to the quantity of energy that can be extracted, which is independent of
design. The energy extraction is maintained in a flow process through the reduction of kinetic energy

149
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

and subsequent velocity of the wind. The magnitude of energy harnessed is a function of the
reduction in air speed over the turbine. 100% extraction would imply zero final velocity and therefore
zero flow. The zero flow scenario cannot be achieved hence all the winds kinetic energy may not be
utilised. This principle is widely accepted and indicates that wind turbine efficiency cannot exceed
59.3%. This parameter is commonly known as the power coefficient Cp, where max Cp = 0.593
referred to as the Betz limit . The Betz theory assumes constant linear velocity. Therefore, any
rotational forces such as wake rotation, turbulence caused by drag or vortex shedding (tip losses) will
further reduce the maximum efficiency.

2.2 Practical Efficiency

In practice rotor designs suffer from the accumulation of minor losses resulting from:

1. Tip losses
2. Wake effects
3. Drive train efficiency losses
4. Blade shape simplification losses

Comparison of Different Wind Turbines

Table. 1: Comparison of wind turbines.

J- Type Vertical Axis Wind Turbine

J type wind turbine is basically a drag type wind turbine. Our aim was to produce electricity
at low cost. The procedure for other turbines especially lift type turbines was too expensive and
hence this led us to choose the drag type wind turbines with less complexities involved in
construction.

150
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

Wind Turbine Design Parameters: [4]

The wind turbine parameters considered in the design process are:

i. Swept area
ii. Power and power coefficient
iii. Tip speed ratio
iv. Blade chord
v. Number of blades
vi. Solidity

3. DESIGN CALCULATIONS

3.1 Power calculations

The wind turbine works on the principle of converting kinetic energy of the wind to
mechanical energy. The kinetic energy of any particle is equal to one half its mass times the square of
its velocity,
K.E=½mv2.………………….. (1)

Where,
K.E = kinetic energy
m = mass
v = velocity,
M is equal to its Volume multiplied by its density ρ of air

M = ρAV ………………….. (2)

Substituting eq. (2) in eq. (1)

We get,
K E = ½ρAV.V2
K E = ½ρAV3watts.

Where,
A= swept area of turbine.
ρ= density of air (1.225 kg/m3)
V=wind velocity.
For 35 Watt power, calculate design parameters of turbine, P=35 watts.

Considering turbine efficiency as 25% and generator efficiency 85%,

P = 35/ (0.25*0.85)
P= 166 watts.
= ½ρAV3
For wind velocity 6.67 m/s (18mph)
Density of air (1.225 kg/m3)
166 = ½*1.125*A*(6.67)3
A= 1 Sq.m
A = D*H (Sq.m)
D= diameter of the blade
Taking diameter as 1 meter, height of turbine can be calculated as

151
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

H=A/D =1/1
H =1m.
Diameter and height of wind turbine are 1m and 1m2.

Design of Turbine Blades [6]

Wing width= diameter*0.14
= 1*0.14
= 0.140m = 140 mm
Wing chord = circumference*.09
= π*1*.09
= 0.282m = 282mm

Fig 3: Blade parameters

Block diagram

Fig. 4: Block Diagram

152
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

4. CAD DESIGN

Wooden frame

Blades

Exploded view

153
International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

Assembly

5. DESIGN SPECIFICATIONS

Table.2: Turbine specifications

Wind rotor Rated power 35W
Cut in speed 3 m/s
Rated speed 6.67 m/s
Rotor diameter 1m
Swept area 1 m^2(1 m*1 m)
Gear box type None gear box, direct given to
generator
Brake Not required

Generator Generator type DC generator

Electric Transmission Brushless
Turbine blade Blade type J-type(drag)
Blade number 3
Blade material GI sheet with Wooden frame
Hub material MS
Blade dimension Length 1m
Cup radius 0.126 m
Controller PC16877A

Observation Table

Table 3: Observation table

Sr.No. Speed Voltage Current Power
(rpm) (Volts) (Ampere) (Watts)

1 30 4.39 1.86 8.16

2 39 4.64 2.28 10.61
3 48 5.73 2.28 13.06
4 70 6.14 2.98 17.78
5 97 7.16 3.64 26.39

154
 International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 – 6340(Print),
ISSN 0976 – 6359(Online), Volume 5, Issue 10, October (2014), pp. 148-155 © IAEME

6. RESULT DISCUSSION

The results obtain were up to expectations. While in theoretical design we considered the
efficiency of turbine to be 25%, but we got efficiency as 23.3%. The efficiency was decreased due
various manufacturing errors and friction losses

7. CONCLUSION

Our work and the results obtained so far are very encouraging and reinforce the conviction
that vertical axis wind energy conversion systems are practical and potentially very contributive to
the production of clean renewable electricity from the wind even under less than ideal siting
conditions this project will be helpful in rural areas where the electricity supply is scarce. Also in
most cities, bridges are a faster route for everyday commute and in need of constant lighting makes
this an efficient way to produce energy

8. FUTURE SCOPE

The efficiency can be increased by precise fabrication of prototype and also by designing the
blades of the turbine more aerodynamically and use simulation software like CFD. The development
of effective alternators and dynamos can be used to harness wind energy from relatively small winds.
The use of materials like Acrylic Plastic Sheets can be used to develop low cost VWAT.

REFERENCES

1. Peter J. Schubel and Richard J. Crossley, Wind Turbine Blade Design, Energies, 2012, 5,
3425-3449.
2. W. Denson, The history of reliability prediction, failure causes for electronic systems, IEEE
Trans Reliab, 1998, Vol. 47, p. 325.
3. P. Gipe, Wind Power, James & James, London, 2004, p. 85-88.
4. Javier Castillo, Small-scale Vertical Axis Wind Turbine Design Bachelor’s Thesis, December
2011, Degree program in Aeronautical Engineering, Tampereen ammattikorkeakoulu
Tampere University of Applied Sciences.
5. www.windgenkits.com
6. www.windstuffnow.com
7. T. Vishnuvardhan and Dr. B. Durga Prasad, “Finite Element Analysis and Experimental
Investigations on Small Size Wind Turbine Blades”, International Journal of Mechanical
Engineering & Technology (IJMET), Volume 3, Issue 3, 2012, pp. 493 - 503, ISSN Print:
0976 – 6340, ISSN Online: 0976 – 6359.
8. M.Z.I.Sajid, Dr. K.Hema Chandra Reddy and Dr. E.L.Nagesh, “Design of Vertical Axis Wind
Turbine for Harnessing Optimum Power”, International Journal of Mechanical Engineering &
Technology (IJMET), Volume 4, Issue 2, 2013, pp. 172 - 177, ISSN Print: 0976 – 6340,
ISSN Online: 0976 – 6359.
9. Navin Kumar Kohli and Eshan Ahuja, “Performance Prediction in HAWT Wind Power
Turbine”, International Journal of Mechanical Engineering & Technology (IJMET),
Volume 2, Issue 2, 2011, pp. 14 - 24, ISSN Print: 0976 – 6340, ISSN Online: 0976 – 6359.

155

View publication stats