DDX395 DDX375BT DDX350BT Ddx25Bt DDX418BT: Instruction Manual

ENGLISH
MONITOR WITH DVD RECEIVER

INSTRUCTION MANUAL
DDX395 (Region 1 – DVD Region Code 1 Area) DDX25BT (Region 1 – DVD Region Code 1 Area)
DDX375BT (Region 1 – DVD Region Code 1 Area) DDX418BT (Region 4 – DVD Region Code 4 Area)
DDX350BT (Region 1 – DVD Region Code 1 Area)
This instruction manual is used to describe the models listed above. Model availability and features (functions) may differ depending on the country and
sales area.
Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new DVD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and
serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model DDX395/DDX375BT/DDX350BT/DDX25BT/DDX418BT Serial number
US Residents Only
Register Online
Register your Kenwood product at www.kenwood.com/usa/
© 2017 JVC KENWOOD Corporation B5A-2142-10 (KN/RN)
01_DDX_2018ST_KR_COVER.indd 1 9/5/2017 5:25:52 PM

Important Notice
To ensure proper use, please read through this For DDX418BT:
manual before using this product. It is especially
CAUTIONS
important that you read and observe WARNINGS To care for the unit
and CAUTIONS in this manual. • If you have parked the car for a long time in hot or
Please keep the manual in a safe and accessible cold weather, wait until the temperature in the car
place for future reference. becomes normal before operating the unit.
To care for the monitor The marking of products using lasers
• The monitor built into this unit has been produced The label is attached to the chassis/case and says
WARNINGS with high precision, but it may have some ineffective that the component uses laser beams that have been
To prevent accidents and damages dots. This is inevitable and is not considered classified as Class 1. It means that the unit is utilizing
• DO NOT install any unit or wire any cable in a defective. laser beams that are of a weaker class. There is no
location where; • Do not expose the monitor to direct sunlight. danger of hazardous radiation outside the unit.
– it may obstruct the steering wheel and gearshift • Do not operate the touch panel using a ball-point
lever operations. pen or similar tool with a sharp tip. For DDX395/DDX375BT/DDX350BT/DDX25BT:
– it may obstruct the operation of safety devices such Touch the keys on the touch panel with your finger CAUTION
as air bags. directly (if you are wearing a glove, take it off). Use of controls or adjustments or performance
– it may obstruct visibility. • When the temperature is very cold or very hot... of procedures other than those specified herein
• DO NOT raise the volume level too much, as this will – Chemical changes occur inside, causing may result in hazardous radiation exposure. In
make driving dangerous by blocking outside sounds, malfunction. compliance with Federal Regulations, the following
and may cause hearing loss. – Pictures may not appear clearly or may move are reproductions of labels on, or inside the product
• DO NOT operate the unit while driving. If you need slowly. Pictures may not be synchronized with relating to laser product safety.
to operate the unit while driving, be sure to look the sound or picture quality may decline in such
around carefully. environments.
• Stop the car before performing any complicated On the volume setting
operations. • Digital devices produce very little noise compared
• The driver must not watch the monitor while driving. with other sources. Lower the volume before playing
these digital sources to avoid damaging the speakers
Location : Top plate
by sudden increase of the output level.
i ENGLISH
EN_DDX2018ST_KR.indb i 2017/05/17 9:27

Important Notice
For DDX395/DDX375BT/DDX350BT/DDX25BT: FCC NOTE For DDX395/DDX375BT/DDX350BT/DDX25BT:
CAUTION This equipment has been tested and found to comply IC (Industry Canada) Notice
with the limits for a Class B digital device, pursuant This device complies with Industry Canada’s licence-
This equipment complies with FCC/IC radiation to Part 15 of the FCC Rules. These limits are designed exempt RSSs. Operation is subject to the following two
exposure limits set forth for an uncontrolled to provide reasonable protection against harmful conditions:
environment and meets the FCC radio frequency interference in a residential installation. (1) This device may not cause interference; and
(RF) Exposure Guidelines and RSS-102 of the IC radio This equipment may cause harmful interference to (2) This device must accept any interference, including
frequency (RF) Exposure rules. This equipment has radio communications, if it is not installed and used interference that may cause undesired operation of
very low levels of RF energy that is deemed to comply in accordance with the instructions. However, there the device.
without maximum permissive exposure evaluation is no guarantee that interference will not occur in a
(MPE). But it is desirable that it should be installed and particular installation. If this equipment does cause
operated keeping the radiator at least 20 cm or more harmful interference to radio or television reception,
away from person’s body. which can be determined by turning the equipment
• Contains Transmitter Module off and on, the user is encouraged to try to correct the
FCC ID: ZWY8811X interference by one or more of the following measures:
• Contains Transmitter Module • Reorient or relocate the receiving antenna.
IC: 12033A-8811X • Increase the separation between the equipment and
receiver.
For DDX395/DDX375BT/DDX350BT/DDX25BT: • Connect the equipment into an outlet on a
FCC WARNING circuit different from that to which the receiver is
This equipment may generate or use radio connected.
frequency energy. Changes or modifications to this • Consult the dealer or an experienced radio/TV
equipment may cause harmful interference unless technician for help.
the modifications are expressly approved in the
instruction manual. The user could lose the authority This transmitter must not be co-located or operated in
to operate this equipment if an unauthorized change conjunction with any other antenna or transmitter.
or modification is made.
ENGLISH ii
EN_DDX2018ST_KR.indb ii 2017/05/17 9:27

About this manual Contents
The displays and panels shown in this manual are Component Names and Operations ............... 3 Using an external component via ADS adapter—
examples used to provide clear explanations of the OEM Features ................................................................................ 33
Basic Operations ................................................. 4
operations. For this reason, they may be different Bluetooth® .........................................................34
How to reset your unit .................................................................4
from the actual displays or panels. Turning on the power ..................................................................4 Information ...................................................................................... 34
Turning off the power ..................................................................4 Preparation ....................................................................................... 34
Illustrations of DDX395 are mainly used for Connection....................................................................................... 34
Putting the unit in standby .......................................................4
explanation. Bluetooth mobile phone ......................................................... 36
Turning off the screen ..................................................................4
Adjusting the volume ...................................................................5 Bluetooth audio player ............................................................. 38
This manual mainly explains operations using the
Attenuating the sound ...............................................................5 KENWOOD Music Mix ............................................................ 38
buttons on the monitor panel and keys on the
Bluetooth settings ....................................................................... 39
touch panel. For operations using the remote Getting Started ................................................... 5
controller, see page 48. Initial settings .....................................................................................5 Settings ..............................................................40
Setting the security function....................................................6 Audio settings ................................................................................ 40
< > indicates the various screens/menus/ Clock settings.....................................................................................6 Display settings.............................................................................. 43
operations/settings that appear on the touch Input settings .................................................................................. 45
Various Screens and Operations ..................... 7
panel. System settings.............................................................................. 45
Home screen ......................................................................................7
Source control screen...................................................................8 Remote Controller ............................................48
[ ] indicates the keys on the touch panel. List/setting screen...........................................................................9 Preparation ....................................................................................... 49
Basic operations for RC-DV340 (supplied) .................... 49
Indication language: English indications are used Disc ......................................................................10
Basic operations for KNA-RCDV331 (optionally
for the purpose of explanation. You can select the Video ...................................................................11 purchased)........................................................................................ 51
indication language from the <Setup> menu. KENWOOD Remote APP ...................................................... 53
USB ......................................................................13
(Page 45)
Android...............................................................15 Installation and Connection ...........................53
Before installation ........................................................................ 53
iPod/iPhone .......................................................16 Installing the unit.......................................................................... 55
Radio ...................................................................17 Removing the unit ..................................................................... 55
SiriusXM® Satellite Radio ................................19 Wiring connection ....................................................................... 56
Connecting external components .................................... 57
Pandora® ............................................................26
References .........................................................57
iHeartRadio ........................................................28 Maintenance ................................................................................... 57
Spotify ................................................................30 More information ......................................................................... 57
Other External Components ..........................32 Troubleshooting ...............................................61
AV-IN ................................................................................................... 32 Specifications ....................................................64
Rear view camera ........................................................................ 32 Trademarks and licenses.......................................................... 67
2 ENGLISH
EN_DDX2018ST_KR.indb 2 2017/05/17 9:27

Component Names and Operations
DDX395/DDX375BT 7 CAM/DISP OFF button DDX350BT/DDX25BT/DDX418BT
• CAM (Press): Displays the picture from the
connected rear view camera.
• DISP OFF (Hold): Turns off the screen.
8 TEL/VOICE button
• TEL (Press): Displays the phone control screen.
• VOICE (Hold): Activates voice dialing.
9 Volume/MENU/ATT knob
• Volume (Turn): Adjusts the audio volume.
• MENU (Press): Pops up the short-cut menu.
• ATT (Hold) Attenuates the sound.
1 Reset button/Power indicator/Security indicator 1 Reset button/Power indicator/Security indicator

• Resets the unit. • Resets the unit.
• Lights up while the unit is turned on. • Lights up while the unit is turned on.
• Flashes when the security function is activated. • Flashes when the security function is activated.
2 M button 2 M button
3 Loading slot 3 Loading slot
4 Screen (touch panel) 4 Screen (touch panel)
5 Monitor panel 5 Monitor panel
6 HOME button 6 HOME button
• (Press): Turns on the power. • (Press): Turns on the power.
• (Hold): Turns off the power. • (Hold): Turns off the power.
• HOME (Press): Displays the Home screen while • HOME (Press): Displays the Home screen while
the power is on. the power is on.
7 MENU/CAMERA button
• MENU (Press): Pops up the short-cut menu.
• CAMERA (Hold): Displays the picture from the
8 TEL/VOICE button
• TEL (Press): Displays the phone control screen.
• VOICE (Hold): Activates voice dialing.
9 Volume J/K buttons
ENGLISH 3
EN_DDX2018ST_KR.indb 3 2017/05/17 9:27

Basic Operations
How to reset your unit Putting the unit in standby Turning off the screen
If the unit fails to operate properly, press the reset On the pop-up short-cut menu
button.
1 Display the source/option selection
screen. 1 Display the pop-up short-cut menu.
On the Home screen, touch as follows:
DDX395/DDX375BT DDX350BT/DDX25BT/
DDX418BT
Turning on the power

2 Put the unit in standby.
On the source/option selection screen, touch as
follows: 2 On the pop-up short-cut menu, touch as
follows:
Display OFF
Turning off the power

To turn on the screen: Touch the screen.
On the monitor panel

(Only for DDX395/DDX375BT)
(Hold)
(Hold)
To turn on the screen: Press and hold DISP OFF on
the monitor panel or touch the screen.
4 ENGLISH
EN_DDX2018ST_KR.indb 4 2017/05/17 9:27

Basic Operations Getting Started
Adjusting the volume Initial settings <Language>
Select the text language used for on-screen
DDX395/DDX375BT When you power on the unit for the first time or reset information.
the unit, the <Initial Setup> screen appears. • English (Initial)/Español/Français/Deutsch/
Perform the initial settings. Italiano/Nederlands/Ελληνικά/Português/Türkçe/
Čeština/Polski/Magyar/Руccĸий/ / /
Initial Setup
/ / / /Bahasa
Demonstration ON OFF
Malaysia/Bahasa Indonesia/
You can adjust the volume (00 to 35) by turning Language English
Rear Camera Enter
– For external monitors, only English/Spanish/
the knob to the right to increase and to the left to
User Customize Enter French/German/Italian/Dutch/Russian/Portuguese
decrease.
Viewing Angle Enter are available. If another language has been
selected, the text language for external monitors
DDX350BT/DDX25BT/DDX418BT Finish
will be set to English.
• GUI Language (Local (the language selected
E.g. Initial settings screen for DDX395 above)/English (Initial)): Selects the language used
for displaying operation keys and menu items.
Once completed, Home screen appears.
“Please Power Off” appears when the setting is
changed. Turn off the power, then turn on to enable
You can adjust the volume (00 to 35) by pressing J to <Demonstration>
the change.
increase and pressing K to decrease. • ON (Initial): Activates the display demonstration.
• OFF: Deactivates the display demonstration. <Rear Camera> (Page 45)
• Holding J increases the volume continuously to
Make the settings to display the picture from the
level 15.
<User Customize> (Page 43)
Attenuating the sound Change the display design.
<Viewing Angle>
Select the viewing angle in relation to the monitor
panel to make the panel easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
(Hold)
The ATT indicator lights up.
To cancel attenuation: Press the same button again.
ENGLISH 5
EN_DDX2018ST_KR.indb 5 2017/05/17 9:27

Getting Started
Setting the security function 4 Repeat step 3 to confirm your security Clock settings
code.
Registering a security code Now, your security code is registered. 1 Display the Home screen.
(Only for DDX418BT)
To clear the registered security code: touch [CLR]
1 Display the Home screen. for <Security Code> in step 2.
Then, enter the current security code to clear and
touch [Enter].
2 Display the <Clock> screen.
• When the unit has been reset or disconnected from On the Home screen, touch as follows:
the battery, you are required to enter the security
2 Display the <Security Code Set> screen. code. Enter the correct security code, then touch
On the Home screen, touch as follows: [Enter].
Then, on the <Setup> screen, touch as follows:
Activating the security function [System] → <Clock> : [Enter]
You can activate the security function to protect your • You can also display the <Clock> screen by
Then, on the <Setup> screen, touch as follows: receiver system against theft. touching the clock area on the Home screen.
[System] → <Security Code> : [Set] 1 Display the <Setup> setting screen. 3 Set the clock time.
3 Enter a four-digit number (1), then On the Home screen, touch as follows: Clock
confirm the entry (2). Synchronize Radio Data System
AM10 : 28
2 Activate the security function. Reset

On the <Setup> setting screen, touch as follows:
[System] → <SI>: [ON]
The security function is activated.
The security indicator on the monitor panel flashes E.g. Clock settings screen for DDX395
• To delete the last entry, touch [Clear]. when the vehicle ignition is off.
<Synchronize>
• To cancel the setting, touch [Cancel]. To deactivate the security function: Touch [OFF] in • Radio Data System: Synchronizes the clock time
step 2. with FM RBDS.
• OFF: Sets the clock manually. Touch [J]/[K] to
adjust the hour, then minute.
– Touching [Reset] will set the minute to “00”.
6 ENGLISH
EN_DDX2018ST_KR.indb 6 2017/05/17 9:27

Various Screens and Operations
You can display or change to other screens at any time Available playback sources and options [Android™] Plays an Android device.
to show information, change the AV source, change
Touch 1 to display the source/option selection screen. [iPod] Plays an iPod/iPhone.
the settings, etc.
[Radio] Switches to the radio broadcast.
Home screen To change the page: Touch [ ]/[ ]. Current page is
DISC USB BT Audio TEL SiriusXM shown by the page indication on the top of the screen.
When you turn on the power for the first time, the
Home screen appears.
To return to the Home screen: Touch [ ] on the
• You can customize the Home screen. (Page 44) Now
OEM Features STANDBY iHeartRadio Spotify Pandora
Playing
source/option selection screen.
• To display the Home screen from other screens, press
HOME. E.g. Source/option selection screen for DDX395
*1 Only for DDX418BT.
Touching the operation keys performs the following *2 Only for DDX395/DDX375BT/DDX25BT.
actions: *3 Only for DDX395/DDX375BT.
[DISC] Plays a disc. *4 Only for DDX395/DDX375BT/DDX350BT/DDX25BT.
[USB] Plays files on a USB device.
[BT Audio] Plays a Bluetooth audio player.
Now
[TEL] Displays the phone control screen.
Playing
[AV-IN]*1 Switches to an external component

connected to the AV-IN input
terminal.
Touching the operation keys performs the following [SiriusXM]*2 Switches to the SiriusXM® radio
actions: broadcast.
1 Displays all playback sources and options.
2 Displays the <Setup> screen. [OEM Switches to the source connected
3 Displays the current playing source control screen. Features]*3 via ADS adapter.
4 Displays the <Clock> screen. [STANDBY] Puts the unit in standby.
5 Selects or changes the playback source. [iHeartRadio]*4 Switches to the iHeartRadio
broadcast.
[Spotify] Switches to the Spotify application.
[Pandora]*4 Switches to the Pandora broadcast.
ENGLISH 7
EN_DDX2018ST_KR.indb 7 2017/05/17 9:27

7 Displays/hides other available operation keys* 8
Source control screen
8 Operation keys*
[ ] Displays the <Equalizer> screen.
You can perform the playback operation from the 9 IN indicator (lights up while a disc is inserted)
source control screen during playback. p Playing time/playback status [ ] Displays the folder list/track list/audio
• The operation keys and information displayed vary q Playback mode indicator (Repeat/Random) menu/video menu.
depending on the selected source/disc type/file type w File type indicator [S]/[T] • (Touch) Selects an item (chapter/
being played. e Current playback item information folder/track/audio file/video file).
• If the operation keys are not displayed on the screen, (folder no./file no./track no./total track no./playback • (Hold) Reverses/forwards search.
touch the screen to show them. file type) • (Hold) Plays in slow-motion while
paused for video playback.
* See the following “Common operation keys on source control
screen”. [IW] Starts/pauses playback.
[ ] Selects random playback mode.*
Common operation keys on source control screen
* About playback mode:
• The appearance of the operation keys may differ,
– Available playback mode differs depending on the source, disc
however the similar operation keys have the same
type, connected device, etc.
operations.
– You cannot activate repeat playback mode and random
• Available operation keys differ depends on the
playback mode at the same time.
selected source or connected device.
– To cancel the playback mode, touch repeatedly until the
E.g. Common audio playback source screen for indicator disappears.
Touching the operation keys performs the following
DDX395 actions:
1 Displays/hides short-cut source selection keys. 7
2 Playback source or media type
3 Picture/artwork (shown if the file contains the [ ] Displays other available operation keys
information) besides those shown on 8.
4 Short-cut source selection keys • To hide the window, touch [ ].
• Touching [ ] on 1 to display the keys, or [ ] [ ][ ] Selects a folder.
to hide them.
[ ] Selects repeat playback mode.*
5 Clock display
6 Track/file/song/video information [o] Stops playback.
• Touching [<] scrolls the text if not all of the text [MODE] Displays the setting screen of the current
is shown. playback source.
8 ENGLISH
EN_DDX2018ST_KR.indb 8 2017/05/17 9:27

Using the pop-up short-cut menu Using touch screen operation during List/setting screen
While displaying the source control screen, you can playback
jump to another screen by touching the operation Below are the common operation keys which appear
keys on the pop-up short-cut menu. on the list/setting screen.
1 Display the pop-up short-cut menu. however the similar operation keys have the same
DDX395/DDX375BT DDX350BT/DDX25BT/ operations.
DDX418BT • Available operation keys differ depends on the
setting screens. Not all these operation keys are
shown on every screen.
Touching the areas performs the following actions:
1 Displays the video control menu while playing a
2 Select an item to jump to by touching as video.
follows. 2 While playing a video: Displays the source control
screen.
[TEL] Displays the phone control screen.
While playing an audio file: Displays the playback
[Screen Displays the picture adjustment operation keys.
Adjustment] screen. 3 Goes to the previous chapter/track.*
[Display OFF] Turns off the screen. 4 Goes to the next chapter/track.*
[Camera] Displays the picture from the * Not available for video from an external component (AV-IN) (for
connected rear view camera. Touching the operation keys performs the following
DDX418BT only).
actions:
[SETUP] Displays the <Setup> screen. 1 Enters alphabet search* to list the items in
[Current Displays the current source alphabetical order. When a keypad appears, touch
Source] control screen. the first letter you want to search for.
2 Returns to the root folder.
3 Returns to the upper layer.
To close the pop-up menu: Touch the screen
4 Closes the current screen.
anywhere other than the pop-up short-cut menu.
5 Exits from the current screen or returns to the
previous screen.
6 Changes the page to display more items.
* Alphabet search is not available when the playlist is selected.
ENGLISH 9
EN_DDX2018ST_KR.indb 9 2017/05/17 9:27

Disc
• If a disc does not have a disc menu, all tracks on it will Selecting a folder/track on the list
be played repeatedly until you change the source or
Ejecting a disc
eject the disc. 1 Display the folder/track list.
• For playable disc types, file types and other On the source control screen, touch as follows:
information, see pages 57 and 58.
• If “ ” appears on the screen, the unit cannot accept
• When removing a disc, pull it out horizontally.
the operation you have tried to do.
• You can eject a disc while playing another AV source.
– In some cases, without showing “ ”, operations
will not be accepted.
• If the ejected disc is not removed within 15 seconds, 2 Select the folder (1), then the item (2) in
the disc is automatically inserted again into the the selected folder.
• When playing back a multi-channel encoded disc,
loading slot to protect it from dust. DISC
the multi-channel signals are downmixed.
Folder Name 1 File Name 1
Playback operations Folder Name 2 File Name 2
Inserting a disc Folder Name 3 File Name 3
Audio playback information and key Folder Name 4 File Name 4
Label side up Folder Name 5 File Name 5
operation
• For playback information, see “Source control screen”
on page 8. Select an item in each layer until you reach and
• For key operations on the touch panel, see “Common select the desired file.
operation keys on source control screen” on
page 8.
Settings for disc playback
• Available items shown on the <DISC Mode> screen
E.g. Inserting a disc for DDX395 differ depending on the type of disc/file being
played back.
The source changes to “DISC” and playback starts.
• The IN indicator lights up while a disc is inserted. 1 Display the <DISC Mode> screen.
On the source control screen, touch as follows:
10 ENGLISH
EN_DDX2018ST_KR.indb 10 2017/05/17 9:27

Disc Video
2 Make the settings. <Down Mix> Playback operations
DISC Mode When playing back a multi-channel disc, this
Menu Language English SET setting affects the signals reproduced through the Video playback information on the source
Subtitle Language English SET front and/or rear speakers. control screen
Audio Language SET
English • Dolby Surround: Reproduces multi-channel
Dynamic Range Control Dialog
Dolby Surround Stereo
surround sound by connecting an amplifier
Down Mix
Screen Ratio 16:9

compatible with Dolby Surround.
• Stereo (Initial): Reproduces stereo playback
sound.
<Menu language>*1
Select the initial disc menu language. (Initial: <Screen Ratio>
English) Select the monitor type to watch a wide screen
picture on the external monitor.
<Subtitle language>*1
Select the initial subtitle language or turn subtitles 16:9 (Initial) 4:3 LB 4:3 PS
off (Off). (Initial: English)
<Audio language>*1 E.g. Video playback source control screen for
Select the initial audio language. (Initial: English) DDX395
<Dynamic Range Control> <File Type>*2 1 Media type
You can change the dynamic range while playing Select the playback file type when a disc contains 2 Playback status
Dolby Audio encoded discs. different types of files. 3 Current playback item information
• Wide: Reproduces powerful sound at a low • Audio: Plays back audio files. (title no./chapter no./folder no./file no./track no.)
volume level with its full dynamic range. • Still image: Plays back still picture files. 4 Playing time
• Normal: Reduces the dynamic range a little. • Video: Plays back video files. 5 IN indicator (lights up while a disc is inserted)
• Dialog (Initial): Reproduces movie dialog more • Audio&Video (Initial): Plays back audio files and 6 Playback mode indicator (Repeat/Random)
clearly. video files. 7 File type indicator
*1 For list of language codes, see page 59.
*2 For playable file types, see page 57.
If the disc contains no files of the selected type, the existing
files are played in the following priority: audio, video, then still
picture. You can change these settings only while playback is
stopped.
ENGLISH 11
EN_DDX2018ST_KR.indb 11 2017/05/17 9:27

Video
Video menu control operations Touching the operation keys performs the following [Picture Displays the picture adjustment screen.
You can display the video menu control during video actions: Adjust] 1 Touch [DIM ON] or [DIM OFF] to
playback. 1 turn on or off the dimmer.
• Available operation keys differ depend on the [ZOOM]*1 Displays the picture size selection 2 Touch [+]/[–] to adjust the other
selected disc type and file type. screen. items.
Video playback except VCD 1 Touch [ Zoom] to change the • <Bright>: Adjusts the brightness (−15
magnification level of the picture to +15).
Menu Control
(Zoom1, Zoom2, Zoom3, Full: • <Contrast>: Adjusts the contrast (−10
Initial). to +10).
2 Touch [J] [K] [H] [I] to move the • <Black>: Adjusts the blackness (−10
zooming frame. to +10).
• <Color>: Adjusts the color (−10 to
[Aspect] Displays the aspect ratio selection
+10).
screen.
• <Tint>: Adjusts the tint (−10 to +10).
Touch [ Aspect] to select the aspect
• <Sharpness>: Adjusts the sharpness
E.g. Video menu control screen for DDX395 ratio.
(−2 to +2).
<Full>*2: For 16:9 original pictures
4:3 signal 16:9 signal [Audio] Selects the audio type.
[Subtitle] Selects the subtitle type.
[Angle] Selects the view angle.
<Just>: For viewing 4:3 pictures *1 When [Aspect] is set to <Just> or <Auto>, the picture is
naturally on the wide screen zoomed with the aspect ratio of the <Full> setting.
4:3 signal 16:9 signal This feature may not be used for some video sources.
*2 While DivX is played back with <Screen Ratio> set to [16:9]
(Page 11 for discs/Page 14 for USB), the aspect ratio may
<Normal>*2: For 4:3 original pictures not be set correctly.
4:3 signal 16:9 signal
<Auto>: For “DISC” source and

“USB” source only: The aspect ratio is
automatically selected to match the
incoming signals.
12 ENGLISH
EN_DDX2018ST_KR.indb 12 2017/05/17 9:27

Video USB
2 Touching the operation keys performs the following You can connect a USB mass storage class device such
actions: as a USB memory, digital audio player, etc. to the unit.
[ MENU] Displays the disc menu (DVD).
• For playable file types and other information, see
1
[T MENU] Displays the disc menu (DVD). pages 57 and 60.
[ZOOM] • You cannot connect a PC or portable HDD to the
[Highlight] Switches to the direct disc menu mode.
Touch the target item to select. [Aspect] Refer to “Video playback except VCD” on USB input terminal.
[Picture page 12. • You cannot connect a USB device via a USB hub.
[CUR] Displays the menu/scene selection
screen. Adjust]
• [J] [K] [H] [I]: Selects an item. Connecting a USB device
2
• [Enter]: Confirms the selection. USB device* (commercially available)
• [Return]: Returns to the previous [ MENU] Displays the disc menu.
screen. [Audio] Selects the audio channel
(ST: stereo, L: left, R: right).
Video playback for VCD [Direct]* Displays or hides the direct selection
buttons. Rear panel
Menu Control
1 Touch [DIR/CLR] to select a track
directly on a VCD.
2 Touch the numbers ([0], [1] to [9]) to
select the desired track.
3 Touch [Enter] to confirm.
To delete the last entry, touch [DIR/
E.g. Video menu control screen for DDX395 CLR].
[Return] Displays the previous screen or menu.
* You need to stop playback to deactivate the PBC function when
playing a VCD with PBC activated. The source changes to “USB” and playback starts.
• All tracks in the USB device will be played repeatedly
until you change the source or disconnect the USB
device.
* Use CA-U1EX for extending the cable if necessary. (Max 500 mA,
5V)
ENGLISH 13
EN_DDX2018ST_KR.indb 13 2017/05/17 9:27

USB
Playback operations Selecting a folder/track on the list Settings for USB playback
Playback information and key operation 1 Display the folder/track list. 1 Display the <USB Mode> screen.
• For playback information, see “Source control screen” On the source control screen, touch as follows: On the source control screen, touch as follows:
on page 8.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page 8. 2 Select the folder (1), then the item (2) in
the selected folder. 2 Make the settings.
Selecting the file type to play USB Mode
USB List
You can specify the file type to play. File Name 1
Screen Ratio 16:9
Folder Name 1
Drive Select Next
USB Folder Name 2 File Name 2
File type Audio

Select an item in each layer until you reach and <Screen Ratio>
select the desired file. Select the monitor type to watch a wide screen
E.g. USB source control screen for DDX395 picture on the external monitor.
16:9 (Initial) 4:3 LB 4:3 PS
Select the file type as follows:
[Audio] Plays back audio files.
[Video] Plays back video files.
[Photo] Plays back still picture files. <Drive Select>
• Next: Switch between internal memory and the
If the USB contains no files of the selected type, the memory source of the connected device (such as
existing files are played in the following priority: audio, a mobile phone).
video, then still picture. You can change these settings
only while playback is stopped.
14 ENGLISH
EN_DDX2018ST_KR.indb 14 2017/05/17 9:27

Android
This unit supports the Android™ application, Android (commercially available) Playback operations
KENWOOD Music Play. When you use KENWOOD
Music Play via this unit, you can search for audio files Playback information and key operation
by genre, artist, album, playlist and song.
• For more information about KENWOOD Music Play,
on page 8.
visit <www.kenwood.com/cs/ce/>.
• For key operations on the touch panel, see “Common
USB cable (commercially available) operation keys on source control screen” on
Preparation page 8.
Installing KENWOOD Music Play Selecting a track from the menu

Install the Android™ application, KENWOOD Music Play,
on your Android device beforehand. 1 Display the audio menu.
• When a compatible Android device is connected, On the source control screen, touch as follows:
“Press [VIEW] to install KENWOOD MUSIC PLAY Rear panel
APP” is shown on the Android device. Follow the
instructions to install the application.
• You can also install the latest version of KENWOOD
Music Play on your Android device before
2 Select a category (1), then select a
connecting.
desired item (2).
Android
Playlists Artist 1
Connecting an Android device
Artist Artist 2
This unit supports Android OS 4.1 and above. Album Artist 3
• Some Android devices (with OS 4.1 and above) may Songs Artist 4
not fully support Android Open Accessory (AOA) 2.0. Genres Artist 5
• If the Android device supports both mass storage
class device and AOA 2.0, this unit always plays back Start playback
via AOA 2.0 as priority. Select an item in each layer until you reach and
1 Turn on KENWOOD Music Play on your select the desired file.
Android device.
2 Select “Android” as the source.
ENGLISH 15
EN_DDX2018ST_KR.indb 15 2017/05/17 9:27

Android iPod/iPhone
Bluetooth connection
Settings for Android playback Connecting an iPod/iPhone
Pair the iPod/iPhone with this unit via Bluetooth.
• For playable iPod/iPhone types and other (Page 34)
1 Display the <Android MODE> screen.
information, see page 60.
• You cannot watch video. Selecting the playback device via the
Wired connection connection method
iPod/iPhone iPod/iPhone 30-pin See <Smartphone Setup> on page 46 for more
Lightning model connector model information.
2 Make the settings. (commercially available) (commercially available)
Android MODE
Artwork ON OFF Playback operations

Android Setup BROWSE MODE
Playback information and key operation
on page 8.
USB Audio cable USB Audio cable • For key operations on the touch panel, see “Common
for iPod/iPhone: for iPod/iPhone: operation keys on source control screen” on
<Artwork> KCA-iP103 (optional KCA-iP102 (optional page 8.
• ON (Initial): Shows the artworks of the playing accessory) accessory)
files. Additional keys operations. Touching the operation
• OFF: Hides the artworks of the playing files. keys performs the following actions:
<Android Setup> Switches the device on <Smartphone
Rear panel [ ]
• BROWSE MODE (Initial): Controls from the unit Setup> screen. (Page 46)
(using the KENWOOD Music Play application).
• HAND MODE: Controls other media player
applications from the Android device (without Selecting an audio file from the menu
using the KENWOOD Music Play application).
– You can play/pause or skip files from the unit. 1 Display the audio menu.
16 ENGLISH
EN_DDX2018ST_KR.indb 16 2017/05/17 9:27

iPod/iPhone Radio
2 Select a category (1), then select a Operation keys on source control screen
Listening to the radio
desired item (2).
Playback information on the source control however the similar operation keys have the same
iPod
operations.
Playlists Artist 000000001
screen
• See also “Common operation keys on source control
Artist Artist 000000002
screen” on page 8.
Album Artist 000000003 Radio
Songs Artist 000000004 Touching the operation keys performs the following
Podcasts Artist 000000005 actions:
6
Select an item in each layer until you reach and
select the desired file. [AME ]* (Hold) Presets stations automatically.
• Available categories differ depending on the type [MONO]* Activates monaural mode for better FM
of iPod/iPhone. reception (stereo effect will be lost).
• The MONO indicator lights up while
Settings for iPod/iPhone playback 1 Selects the band (AM/FM1/FM2/FM3) monaural mode is activated.
2 Text information • To deactivate, touch [MONO] again.
1 Display the <iPod Mode> screen. • Touching [<] scrolls the text if not all of the text [TI]* (For FM RBDS features)
On the source control screen, touch as follows: is shown. Activates TI standby reception mode.
• Touching [Radio Text] switches the information • When TI is activated, the unit is ready
between Radio Text, Radio Text Plus and PTY to switch to traffic information if
code. available. The TI indicator lights up in
3 Current station frequency white.
2 Make the settings. 4 Displays the preset stations window (Page 18) • If the TI indicator lights up in orange,
iPod Mode 5 [P1] – [P5] tune into another station providing
Artwork ON OFF • (Touch) Selects a preset station. Radio Broadcast Data System signals.
• (Hold) Presets the current station. • The volume adjustment for Traffic
6 Displays/hides other available operation keys* Information is automatically
7 TI indicator memorized. The next time the unit
<Artwork> switches to Traffic Information, the
8 ST/MONO indicator
• ON (Initial): Shows the artworks of the playing volume is set to the memorized level.
9 Seek mode indicator
files. • To deactivate, touch [TI] again.
p Operation keys*
• OFF: Hides the artworks of the playing files.
* See the following “Operation keys on source control screen”.
ENGLISH 17
EN_DDX2018ST_KR.indb 17 2017/05/17 9:27

Radio
p
Presetting stations in the memory Selecting a preset station
[PTY]* (For FM RBDS features)
You can preset five stations for each band.
Enters PTY search mode. 1 Select the band, then display the preset
1 Touch [PTY]. station window.
2 Touch and hold a PTY code to search Automatic presetting — AME (Auto On the source control screen, touch as follows:
for. Memory) (for FM only)
If there is a station broadcasting a On the source control screen, touch as follows:
program of the same PTY code as you
have selected, that station is tuned in.
[SEEK] Changes the seek mode for [S]/[T]. 2 Select a preset station.
• AUTO1 (Initial): Auto search (Hold)
Radio
• AUTO2: Tunes in preset stations one The local stations with the strongest signals are found
P1
after another and stored automatically.
• MANU: Manual search
[S]/[T] Searches for a station. Manual presetting
• The search method differs according
to the selected seek mode (see above).
1 Tune in to a station you want to preset.
* Appears only when FM is selected as the source. E.g. Preset station window for DDX395
To hide the window: Touch [ ].

2 Select a preset number to store into.
Radio
P1
(Hold)
E.g. Radio source control screen for DDX395
The station selected in step 1 is stored into the

preset number [P1] to [P5] you have selected.
18 ENGLISH
EN_DDX2018ST_KR.indb 18 2017/05/17 9:27

SiriusXM® Satellite Radio (Only for DDX395/DDX375BT/DDX25BT)
Only SiriusXM® brings you more of what you love 1 Displays/hides other available operation keys*
Activating subscription
to listen to, all in one place. Get over 140 channels, 2 Selects the band (SXM1/SXM2/SXM3/SXM4)
including commercial-free music plus the best sports, 1 Check your Radio ID. 3 Channel number
news, talk, comedy and entertainment. Welcome to The SiriusXM Satellite Radio ID is required 4 Text information
the world of satellite radio. A SiriusXM Connect Vehicle for activation and can be found by tuning to • Touching [] scrolls the text if not all of the text
Tuner and subscription are required. Channel 0 as well as on the label found on the is shown.
For more information, visit <www.siriusxm.com>. SiriusXM Connect Vehicle Tuner and its packaging. • Touching [Song Title]/[Info]/[Category]
• The Radio ID does not include the letters I, O, S or switches the information.
Preparation F. 5 Displays the preset channel window
• To hide the window, touch [ ].
Connecting the SiriusXM Connect Vehicle 2 Activate the subscription. 6 [P1] – [P5]
For users in the U.S.A: • (Touch) Selects a preset channel.
Tuner • Online: Visit <www.siriusxm.com/activatenow> • (Hold) Presets the current channel.
Perform this installation when you install the unit for • Phone: Call SiriusXM Listener Care at 7 Playback status and time code for the buffered data
the first time. 1-866-635-2349 and replay mode
Antenna For users in Canada: • The time code shows you the point in the Replay
• Online: Visit <www.siriusxm.ca/activatexm> buffer you are listening to. (E.g. “–5:00” means
SiriusXM Connect Vehicle • Phone: Call XM Customer Care at 1-877-438-9677 that you are listening to audio that is 5 minutes
Tuner (commercially
available)
3 Confirm the activation. behind the current broadcast.)
A confirmation message appears. Touch [Return]. 8 Replay time bar for replay mode
Rear panel • Black: The remaining capacity
• Blue: The amount of buffered contents
Listening to the SiriusXM® Satellite Radio 9 Signal strength indicator
Playback information on the source control p Seek mode indicator
q Operation keys*
screen
* See “Operation keys on source control screen” on page 20.
SiriusXM
ENGLISH 19
EN_DDX2018ST_KR.indb 19 2017/05/17 9:27

SiriusXM® Satellite Radio
Operation keys on source control screen q • To list all the channels, touch [All Channels].
• See also “Common operation keys on source control • Touch the info change key above the list
[ ] Displays the <Channel List> screen.
screen” on page 8. ([Channel]/[Artist]/[Song Title]/[Info]) to
[IW] Starts/pauses the content replay. display other information in the following order:
Touching the operation keys performs the following [CHJ]/[CHK] Selects the channel. Channel, Artist, Song Title, Content Info.
actions: • To select a channel, make sure
1 “SEEK1” is selected as the seek Presetting channels in the memory
[MODE] Displays the <SiriusXM Mode> mode.
screen. • To select a preset channel, make You can preset five channels for each band.
[ ] (Hold) Registers the current artist to sure “SEEK2” is selected as the seek 1 Tune in to a channel you want to preset.
the alert contents. mode.
[ ] (Hold) Registers the current song to

the alert contents. Selecting a channel on the list
[ ] Activates or deactivates the content You can obtain information on channels or select a 2 Select a preset number to store into.
alert for traffic and weather. channel to listen to. SiriusXM
[SEEK] Changes the seek mode for [CHJ]/
[CHK].
1 Display the <Channel List> screen. P1
100Ch
On the source control screen, touch as follows: 105Ch

• SEEK1 (Initial): Skips to another
available channel. 110Ch
• SEEK2: Skips to another preset 115Ch
(Hold)
channel. 120Ch
[SCAN] Starts TuneScan™. 2 Select a category (1), and then select a

The channel selected in step 1 is stored into the
[S]/[T]/ Performs playback operations during
channel (2). preset number [P1] to [P5] you have selected.
[Live] content replay. Channel List Channel
All Channels 100Ch Channel Name

[ ] Changes the page in the window to
Category Name 1 105Ch Channel Name
display other operation keys. Category Name 2 110Ch Channel Name
20 ENGLISH
EN_DDX2018ST_KR.indb 20 2017/05/17 9:27

Selecting a preset channel Replaying content [IW] Starts/pauses playback.
You can pause, rewind and replay the contents from [S]/[T] Skips the current track/segment.
1 Select the band, then display the preset
the currently tuned channel. • Touching [S] within 2 seconds
channel window. • The SiriusXM Connect Vehicle Tuner continually of the beginning of the current
On the source control screen, touch as follows: track/segment returns to the
buffers up to 60 minutes of audio.
• If you change to another channel during playback, previous track.
the buffered contents will be lost. • Touching [S] after 2 seconds or
• The time code is updated every second. more of the current track returns
to the beginning of the track.
2 Select a preset channel. 1 Display the operation keys for replay. (Hold) Reverses/forwards search.
SiriusXM
[Live] Returns to the live position.
P1 Channel Name
100Ch
Channel Name
105Ch
Channel Name
110Ch
115Ch
Channel Name
2 Perform the replay operations.
SiriusXM Satellite Radio features
Channel Name
120Ch
SiriusXM SmartFavorites
• You can also select a preset channel by touching User stored channels (P1 to P5) of the current band
[P1]–[P5]. are recognized as SmartFavorites channels. SiriusXM
Connect Vehicle Tuner automatically buffers their
To hide the window: Touch [ ]. broadcast content in the background. When you select
3 Select “SEEK2” as the seek mode to jump a SmartFavorite channel, you can rewind and replay up
to the selected preset channel. to 30 minutes of any of the missed news, talk, sports or
music content.
• SmartFavorites is available only when you connect
an SXV200 or later SiriusXM Connect Vehicle Tuner.
• If you change to another band, the buffered content
is cleared and new channels in the current band will
start buffering.
ENGLISH 21
EN_DDX2018ST_KR.indb 21 2017/05/17 9:27

For teams
TuneStart™ Content Alert
When you select a SmartFavorites channel, you can The unit informs you when receiving the content you
1 Display the <Alert Team Select> screen.
listen to the current song from the beginning. On the source control screen, touch as follows:
are interested in, such as music, information about a
1 Display the <SiriusXM Mode> screen. sports team, weather and traffic information.
Registering items for Contents Alert
Then, on the <SiriusXM Mode> screen, touch as
You can register your favorite artists, songs or teams.
follows:
Up to 50 contents can be registered.
<Alert Team Select> : [Enter]
2 Activate TuneStart™. For artists/songs
While listening to your favorite artist/song: 2 Select the league (1) and the team (2),
On <SiriusXM Mode> screen, touch as follows: then register into the content alert (3).
<TuneStart> : [ON] On the source control screen, touch as follows:
Alert Team Select
To deactivate TuneStart: Touch [OFF] in step 2. League1 Team1
League2 Team2
TuneScan™ (Hold) League3 Team3
League4 Team4
You can get a short preview of the songs you have Touching the operation keys performs the following League5 Team5
missed on each of your SmartFavorites music channels actions:
and the currently tuned music channel. (Hold) Registers the artist of the current
Activate TuneScan™ to start scanning the first 6 [ ]
song.
seconds of the recorded music contents.
[ ] (Hold) Registers the current song.
The unit starts scanning.

• To select the previous/next content, touch
[S] or [T].
• To end scanning and continue listening to the
current song/content, touch [SCAN] again.
• To exit scanning, touch and hold [SCAN].
22 ENGLISH
EN_DDX2018ST_KR.indb 22 2017/05/17 9:27

To delete the registered items: Touch and hold the
Selecting items for Content Alert item you want to delete in step 2.
Activating Content Alert
You can select items (artists/songs/teams) from the The [ ] icon and a check mark appear beside the For artists/songs/teams
registered items on the list to inform you once the unit
receives the information.
selected item. Touch the [ ] icon to delete. 1 Display the <SiriusXM Mode> screen.
To delete all registered contents: Touch and hold
For artists/songs/teams [All Clear ] for <Content Alerts Contents Set> in
1 Display the <Content Alerts Contents Set> step 1.
screen.
On the source control screen, touch as follows: For traffic and weather information 2 Activate Content Alert.
1 Display the <SiriusXM Mode> screen. On <SiriusXM Mode> screen, touch as follows:
On the source control screen, touch as follows: <Content Alerts> : [ON]
To deactivate Content Alert: Touch [OFF] in step 2.
Then, on the <SiriusXM Mode> screen, touch as
follows: For traffic and weather information
<Content Alerts Contents Set> : [Set] On the source control screen, touch as follows:
2 Select the city you desire traffic and
2 Select the category (1), then the item (2). weather information for.
Content Alerts Contents Set
SiriusXM Mode
Artist 000Ch Ch Name Content Alerts ON OFF
Title 000Ch Ch Name Content Alerts Contents Set All Clear
• When a traffic and weather broadcast for the
Set
Team 000Ch Ch Name Alert Team Select Enter
selected city is received, the unit automatically
000Ch Ch Name Traffic Weather Jump City Select switches the channel.
000Ch Ch Name Los Angeles
SiriusXM Reset Reset

To deactivate the Content Alert: Touch [ ] again.
A check mark appears beside the selected item. • When traffic and weather broadcast is received, the
• To show the details of the item, touch [<]. unit automatically switches the channel.
ENGLISH 23
EN_DDX2018ST_KR.indb 23 2017/05/17 9:27

Switching to registered content Setting reception restrictions 3 Enter a new four-digit code, then touch
When an artist/song/team registered for Content Alert [Enter] to confirm.
You can limit access to SiriusXM channels, such as
is being broadcasted, an alert appears on the screen.
those with mature content. 4 Repeat step 3 above to confirm the new
Touch [Jump], then select the item to jump to on the code.
<Content Alerts> screen. Setting or changing the parental code
Content Alerts • The initial setting is “0000”. Activating parental control
Artist 1/ Channel Name • Changing the code does not change the You can set the parental control feature to lock any
Artist 2/ Channel Name
<Parental Lock>/<Parental Lock Channel SiriusXM channels or automatically lock all channels
Song 1/ Channel Name
Song 2/ Channel Name Selection> settings. classified as “mature” by SiriusXM®.
Team 1/ Channel Name
Team 2/ Channel Name 1 Display the <Parental Code Check> 1 Display the <SiriusXM Mode> screen.
screen. On the source control screen, touch as follows:
• To show the details of the item, touch [<].
2 Select the desired mode for <Parental

Then, on the <SiriusXM Mode> screen, touch as Control>.
follows:
[OFF] Deactivates parental control.
<Parental Code> : [Change]
[Mature] Locks channels classified as “mature”
2 Enter the initial four-digit code (0000) (1),
by SiriusXM®.
and then touch [Enter] (2) to confirm.
[User] Locks selected channels.
Parental Code Check
****
Clear 1 2 3
3 Enter the parental code to confirm your
4 5 6
selection.
7 8 9
Cancel 0 Enter
• To clear the last entry, touch [Clear].

• To cancel setting the code, touch [Cancel].
24 ENGLISH
EN_DDX2018ST_KR.indb 24 2017/05/17 9:27

To deactivate parental lock for all locked channels:
Parental Lock channel selection Resetting the SiriusXM Satellite Radio
Select [All Clear] for <Parental Lock Channel
This option allows you to manually select the channels Selection> in step 1, then enter the parental code. settings
to be locked by the parental control feature.
You can reset all the SiriusXM settings you made and
• You can only change the setting if
Skipping unwanted channels restore the initial settings.
<Parental Control> is set to [User].
If you do not want to receive some channels, you can 1 Display the <SiriusXM Mode> screen.
1 Display the <Parental Lock Channel skip them. On the source control screen, touch as follows:
Selection> screen.
1 Display the <Skip Channel Selection>
screen.
2 Reset the setting.

Then, on the <SiriusXM Mode> screen, touch as On the <SiriusXM Mode> screen, touch and hold
follows: as follows:
<Parental Lock Channel Selection> : [SET] Then, on the <SiriusXM Mode> screen, touch as <SiriusXM Reset> : [Reset ]
follows:
2 Enter the parental code. <Skip Channel Selection> : [SET]
The <Parental Lock Channel Selection> screen
appears. 2 Select a category (1), then a channel (2).
A check mark appears beside the selected channel.
3 Select a category (1), then a channel (2). Skip Channel Selection
A check mark appears beside the selected channel.
All Channels 100Ch Channel Name
Parental Lock Channel Selection Category Name 1 105Ch Channel Name
All Channels 100Ch Channel Name Category Name 2 110Ch Channel Name
Category Name 1 105Ch Channel Name Category Name 3 115Ch Channel Name
Category Name 2 110Ch Channel Name Category Name 4 120Ch Channel Name
• To list all the channels, select [All Channels].
• To list all the channels, select [All Channels]. 3 Repeat step 2 to skip multiple channels.
4 Repeat step 3 to set the parental lock on To clear the channel skipping for all skipped
multiple channels. channels: Touch and hold [All Clear ] for <Skip
Channel Selection> in step 1.
ENGLISH 25
EN_DDX2018ST_KR.indb 25 2017/05/17 9:27

Pandora® (Only for DDX395/DDX375BT/DDX350BT/DDX25BT)
You can stream Pandora from iPhone/iPod touch or Install the latest version of the Pandora application on
Playback operations
Android devices. your smartphone.
• Pandora is only available in certain countries. For • For Android devices: Search for “Pandora” in Google Playback information and key operation
more information, visit <www.pandora.com/legal>. play to find and install the most recent version.
• Because Pandora is a third-party service, the • For iPhone/iPod touch: Search for “Pandora” in the
specifications are subject to change without Apple iTunes App Store to find and install the most Pandora
prior notice. Accordingly, compatibility may be recent version.

impaired or some or all of the services may become
unavailable. Connecting the device
• Some functions of Pandora cannot be operated from For Android devices
this unit. Pair the Android device with this unit via Bluetooth.
• For issues using the application, contact Pandora at (Page 34)
<[email protected]>.
For iPhone/iPod touch
• Via USB input terminal: Connect iPhone/iPod touch You can also operate Pandora with optional remote
Preparation with the cable. (Page 16) controller, KNA-RCDV331.
– For Lightning models: Use KCA-iP103 (optional You can only control play, pause and skip with the
Installing the application remote controller.
accessory).
Your smartphone must has built in Bluetooth and the
– For 30-pin connector models: Use KCA-iP102
following profiles must be supported: 1 Displays/hides other available operation keys*
(optional accessory).
• SPP (Serial Port Profile) 2 Picture data
• Via Bluetooth: Pair the iPhone/iPod touch with this
• A2DP (Advanced Audio Distribution Profile) 3 Track information
unit. (Page 34)
Establish an Internet connection using LTE, 3G, EDGE, • Touching [<] scrolls the text if not all of the text
or WiFi. is shown.
Ensure you are logged in to your smartphone Selecting the device
4 Operation keys*
application. If you do not have a Pandora account, you For selecting the playback device via the connection 5 Playing time/playback status
can create one for free from your smartphone or at method to use, see <Smartphone Setup> on
page 46. * See “Operation keys on source control screen” on page 27.
<www.pandora.com>.
26 ENGLISH
EN_DDX2018ST_KR.indb 26 2017/05/17 9:27

Pandora®
Operation keys on source control screen 3 Select a station from the list.
Selecting a station from the list
On the station list
however the similar operation keys have the same 1 Display the list selection screen. Pandora
operations. On the source control screen, touch as follows: Shuffle By Date
• See also “Common operation keys on source control Station Name By Name
screen” on page 8. Station Name
Station Name
Touching the operation keys performs the following Station Name
actions: 2 Select the list type. Station Name
Pandora
1
• To play all the songs in the registered stations
[ ] Adds the current artist to the station list. randomly, touch [Shuffle].
• To sort the list in reverse chronological order,
[ ] Adds the current track to the station list.
Station List Genre List touch [By Date].
[ ] Bookmarks the current track. • To sort the list in alphabetical order, touch [By
Name].
[ ] Switches the device on <Smartphone
• The indicator appears on the right of the
Setup> screen. (Page 46) [Station List] Selects from the station names. item when the station is shared.
4 [Genre List] Selects from the genres. On the genre list
[ ] Displays the list selection screen. Pandora
Thumbs down to the current track and Genre Name 1 Song Name 1
[ ] Genre Name 2 Song Name 2
skips to the next track.
Genre Name 3 Song Name 3
[ ] Registers the current track as a favorite. Genre Name 4 Song Name 4
Genre Name 5 Song Name 5
[IW] Starts/pauses playback.
[T] Skips the current track.
• Not available when the Pandora skip 1 Select a genre.
reaches its limit. 2 Select a station.
The selected station is added to the station list.
ENGLISH 27
EN_DDX2018ST_KR.indb 27 2017/05/17 9:27

iHeartRadio (Only for DDX395/DDX375BT/DDX350BT/DDX25BT)
iHeartRadio is a free, all-in-one digital radio service that Install the latest version of the iHeartRadio application
Playback operations
lets you listen to your favorite live stations or create on your smartphone.
commercial-free, all-music custom stations featuring • For Android devices: Search for “iHeartRadio for Auto” Playback information and keys operation
songs from the artists you select and similar music. in Google play to find and install the most recent
version.
You can stream iHeartRadio from iPhone/iPod touch or • For iPhone/iPod touch: Search for “iHeartRadio for iHeartRadio
Android devices. Auto” in the Apple iTunes App Store to find and
• Because iHeartRadio is a third-party service, the install the most recent version.
specifications are subject to change without
prior notice. Accordingly, compatibility may be Connecting the device
impaired or some or all of the services may become For Android devices
unavailable. Pair the Android device with this unit via Bluetooth.
• Some functions of iHeartRadio cannot be operated (Page 34)
from this unit.
For iPhone/iPod touch You can also operate iHeartRadio with optional remote
• For issues using the application, contact iHeartRadio
• Via USB input terminal: Connect iPhone/iPod touch controller, KNA-RCDV331.
at <http://www.iheart.com/>.
with the cable. (Page 16) You can only control play, pause and skip with the
– For Lightning models: Use KCA-iP103 (optional remote controller.
Preparation accessory).
– For 30-pin connector models: Use KCA-iP102 1 Displays/hides other available operation keys*
Installing the application 2 Picture data
(optional accessory).
Your smartphone must has built in Bluetooth and the 3 Track information
• Via Bluetooth: Pair the iPhone/iPod touch with this
following profiles must be supported: • Touching [<] scrolls the text if not all of the text
unit. (Page 34)
• SPP (Serial Port Profile) is shown.
• A2DP (Advanced Audio Distribution Profile) 4 Operation keys*
Establish an Internet connection using LTE, 3G, EDGE, Selecting the device
5 Playback status
or WiFi. For selecting the playback device via the connection
method to use, see <Smartphone Setup> on * See “Operation keys on source control screen” on page 29.
Ensure you are logged in to your smartphone
application. If you do not have a iHeartRadio account, page 46.
you can create one for free from your smartphone or at
<http://www.iheart.com/>.
28 ENGLISH
EN_DDX2018ST_KR.indb 28 2017/05/17 9:27

iHeartRadio
Operation keys on source control screen *1 Appears only for the custom station screen.
• The appearance of the operation keys may differ, *2 Appears only for the live station screen.
Searching for a station
however the similar operation keys have the same 1 Display the <Station Search> screen.
operations. Selecting the variety level for your custom On the source control screen, touch as follows:
• See also “Common operation keys on source control station
screen” on page 8.
1 Display the variety level selection screen.
Touching the operation keys performs the following On the source control screen, touch as follows:
actions: 2 Select a station.
1 • The items displayed on the <Station Search>
screen differ depending on the information sent
[ ] Creates a custom station from the
from iHeartRadio.
currently playing track content
information. 2 Select the variety type. Station Search
Favorites
[ ] Saves the current station to the Discovery Tuner

Recent Stations
<Favorites> list. Live Radio
Familiar Less Familiar Artist Radio
[ ]*1 Displays the variety level selection
Podcasts
screen.
Switches the device on <Smartphone Mixed
[ ]
Setup> screen. (Page 46) • To return to the top layer, touch [ ].
4 • To return to the upper layer, touch [ ].
[Familiar] Distributes well-known tracks.
[ ] Displays the <Station Search> screen
or the station list. [Mixed] Distributes a mix of artists and
track names.
[ ] Dislikes the currently playing content.
[Less Familiar] Distributes a wide variety of
[ ] Likes the currently playing content. tracks including lesser-known
ones.
[Io]*2 Starts/stops playback.
[IW]*1 Starts/pauses playback.
[SCAN]*2 Scans stations randomly.
[T]*1 Skips the current track.
ENGLISH 29
EN_DDX2018ST_KR.indb 29 2017/05/17 9:27

iHeartRadio Spotify
With Spotify, your music is everywhere. Working out, Install the latest version of the Spotify application on
Editing the <Favorites> list partying or relaxing, the right music is always at your your smartphone.
1 Display the <Station Edit> screen. fingertips. There are millions of songs on Spotify—from • For Android devices: Search for “Spotify” in Google
On the source control screen, touch as follows: old favorites to the latest hits. Just choose the music play to find and install the most recent version.
you love, or let Spotify surprise you. • For iPhone/iPod touch: Search for “Spotify” in the
Apple iTunes App Store to find and install the most
You can stream Spotify from iPhone/iPod touch or recent version.
Then, on the <Station Search> screen, touch as Android devices.
follows: • Because Spotify is a third-party service, the Connecting the device
specifications are subject to change without For Android devices
prior notice. Accordingly, compatibility may be Pair the Android device with this unit via Bluetooth.
impaired or some or all of the services may become (Page 34)
unavailable.
• Some functions of Spotify cannot be operated from For iPhone/iPod touch
2 Select stations (1), then delete the
this unit. • Via USB input terminal: Connect iPhone/iPod touch
selected stations (2). with the cable. (Page 16)
• For issues using the application, contact Spotify at
• A check mark appears beside the selected station. – For Lightning models: Use KCA-iP103 (optional
<www.spotify.com>.
Station Edit accessory).
Station 01 – For 30-pin connector models: Use KCA-iP102
Station 02 Preparation (optional accessory).
Station 03
Installing the application • Via Bluetooth: Pair the iPhone/iPod touch with this
Station 04
Station 05
unit. (Page 34)
Your smartphone must has built in Bluetooth and the
Station 06
following profiles must be supported:
• SPP (Serial Port Profile) Selecting the device
• To return to the top layer, touch [ ]. • A2DP (Advanced Audio Distribution Profile) For selecting the playback device via the connection
• To return to the upper layer, touch [ ]. Establish an Internet connection using LTE, 3G, EDGE, method to use, see <Smartphone Setup> on
or WiFi. page 46.
Ensure you are logged in to your smartphone
application. If you do not have an Spotify account, you
can create one for free from your smartphone or at
<www.spotify.com>.
30 ENGLISH
EN_DDX2018ST_KR.indb 30 2017/05/17 9:27

Spotify
Operation keys on source control screen *1 For DDX395/DDX375BT/DDX350BT/DDX25BT: Purchase optional
Playback operations
• The appearance of the operation keys may differ, remote controller, KNA-RCDV331.
Playback information and key operation however the similar operation keys have the same *2 See “Operation keys on source control screen” above.
operations. *3 Not available for tracks in a playlist.
• See also “Common operation keys on source control *4 Not available for tracks in the Radio.
Spotify screen” on page 8. *5 Available only for premium account users.
Touching the operation keys performs the following Creating your station (Start Radio)
actions: Start Radio is to start a radio channel based on the
1 currently played track.
[ ]*3 Thumbs down to the current track and Create your station.
skips to the next track. On the source control screen, touch as follows:
[ ]*3 Registers the current track as a favorite.
You can also operate Spotify with a remote controller, [ ]*4 *5 Activates/deactivates the shuffle
RC-DV340*1. playback mode.
You can only control play, pause and skip with the Repeats all tracks/cancels the repeat Station is created and playback starts automatically.
[ ]*4
remote controller. playback. • You can personalize your station using thumb up
Repeats the current track/cancels the ([ ]) or thumb down ([ ]).
1 Displays/hides other available operation keys*2 [ ]*4 *5 – You cannot thumb up or down while playing tracks
repeat playback.
2 Picture data in a playlist.
3 Track information [ ] Creates a new station. – Personalizing stations may not be available
• Touching [<] scrolls the text if not all of the text Switches the device on <Smartphone depending on the track.
[ ]
is shown. Setup> screen. (Page 46)
• Touching [ ]/[ ] changes the displayed
information between artist ( ) and album ( ). 4
4 Operation keys*2 [ ] Displays the Spotify menu screen.
5 Playing time/playback status
6 Progress bar [ ]*5 [ ] Selects a track.
[ ][ ] Starts (I)/pauses (W) playback.
[ ] Saves the current track/artist to <Your

Music>.
ENGLISH 31
EN_DDX2018ST_KR.indb 31 2017/05/17 9:27

Spotify Other External Components
Selecting a track AV-IN Rear view camera
(Only for DDX418BT)
1 Display the Spotify menu screen. Install the rear view camera (separately purchased) in
On the source control screen, touch as follows: Connecting an external component the appropriate position according to the instructions
See page 57 for more information. supplied with the rear view camera.
Connecting a rear view camera

Starting playback See page 57 for more information.
2 Select the list type, then select a desired
1 Select “AV-IN” as the source.
• To use the rear view camera, a reverse lead (REVERSE)
item. connection is required. (Page 56)
• The list types displayed differ depending on the 2 Turn on the connected component and
information sent from Spotify. start playing the source. Using the rear view camera
Spotify • For rear camera settings, see <Rear Camera> on
Your Music Changing the AV-IN name page 45.
Browse
You can change the AV-IN name displayed on the To display the rear view camera screen
Radio
source control screen. The rear view screen is displayed by shifting the gear
• This setting does not affect the source name to the reverse (R) position when <Rear Camera
displayed on the Home screen. Interruption> is set to [ON]. (Page 45)
1 Display the <VIDEO Mode> screen. • A caution message appears on the screen. To
• To return to the top layer, touch [ ]. On the source control screen, touch as follows: remove the caution message, touch the screen.
• To return to the upper layer, touch [ ].
You can also display the picture from the rear view
camera manually without shifting the gear to the
reverse (R) position.
2 Select an AV-IN name
On the pop-up short-cut menu, touch as follows:
VIDEO Mode
AV-IN Name VIDEO
32 ENGLISH
EN_DDX2018ST_KR.indb 32 2017/05/17 9:27

Other External Components
Operations while the camera screen is Using an external component via ADS [Satellite Displays the control screen of the
adapter—OEM Features Radio] satellite radio source provided for the
displayed
(Only for DDX395/DDX375BT) vehicle.
To adjust the picture
Touch the area shown below. [Media Displays the control screen of the
By connecting this unit to the bus system of the Player] media player source provided for the
vehicle using iDataLink (commercially available), this vehicle.
unit can access the satellite radio source provided for
[TEL] Displays the control screen of the
the vehicle and vehicle information can be displayed
Bluetooth Hands Free function
on this unit.
Video menu control is shown. For details, see “Video provided for the vehicle.
• Displayable screens, button names, and screen
menu control operations” on page 12. names vary depending on the type of the connected [BT Displays the control screen of the
• To exit video menu control, touch the same area iDataLink and the model of the vehicle. Streaming] Bluetooth streaming function
again. • For details, visit <www.idatalink.com/>. provided for the vehicle.
[Gauges] Displays the information about the
To display parking guide line Connecting an ADS adapter instruments such as a speedometer.
Set <Parking Guidelines> to [ON] (Page 45) or See page 57 for more information.
[Climate] Displays the information about the air
touch the area shown below.
conditioner of the vehicle.
Using an external component via an ADS
[Parking Displays the information about
adapter Assist] the Parking Distance Sensor of the
• For settings to use an ADS adapter, see page 45. vehicle.
• To close the parking guidelines, touch the same area 1 Select “OEM Features” as the source. [Vehicle Info] Displays the information about the
again. On the Home screen, touch as follows: tire pressures of the vehicle.
[Radar Displays the information about the
To exit the camera screen Detector] Radar Detector.
Press HOME on the monitor panel or touch the area
shown below.
2 Turn on the connected component and
start playing the source.
ENGLISH 33
EN_DDX2018ST_KR.indb 33 2017/05/17 9:28

Bluetooth®
Auto pairing
Information Connection
When <Auto Pairing> is set to [ON], Android or iOS
Bluetooth is a short-range wireless radio When you connect a Bluetooth device to the unit for (such as iPhone) devices are automatically paired
communication technology for mobile devices such as the first time: when connected via USB. (Page 39)
mobile phones, portable PCs and other devices. 1 Register the device by pairing the unit and the
Bluetooth devices can be connected without cables device. Pairing a Bluetooth device using SSP (for
and communicate with each other. 2 Connect the device to the unit. (Page 35) Bluetooth 2.1)
When the Bluetooth device is compatible with
Note Registering a new Bluetooth device Bluetooth 2.1, a pairing request is sent from the
• While driving, do not perform complicated available device.
Pairing allows Bluetooth devices to communicate with
operations such as dialing numbers, using the phone
book, etc. When you perform these operations, stop
each other. 1 Search for the unit (“DDX3eX”/“DDX3”/
• The pairing method differs depending on the “DDX4”) from your Bluetooth device.
your car in a safe place. Bluetooth version of the device.
• Some Bluetooth devices may not connect to this unit – For devices with Bluetooth 2.1: 2 Confirm the request both on the device
depending on the Bluetooth version of the device. You can pair the device and the unit using SSP and the unit.
• This unit may not work for some Bluetooth devices. (Secure Simple Pairing) which only requires On the device:
• Connecting conditions may vary depending on your confirmation.
environment. – For devices with Bluetooth 2.0:
• For some Bluetooth devices, the device is You need to enter a PIN code both on the device
disconnected when the unit is turned off. and unit for pairing.
• If your mobile phone supports PBAP (Phone Book • Once the connection is established, it is registered in
Access Profile), you can display the following items the unit even if you reset the unit. Up to five devices
on the touch panel when the mobile phone is On the unit:
can be registered in total.
connected. • Two devices for Bluetooth phone and one for
– Phone book Bluetooth audio can be connected at a time.
– Dialed calls, received calls, and missed calls (up to However, when “BT Audio” is selected as the source,
10 entries in total) you can connect up to five Bluetooth audio devices
and switch between these five devices.
Preparation • To use the Bluetooth function, you need to turn on
the Bluetooth function of the device.
Connect and install the microphone beforehand. For
details, see page 56. To reject the request: Touch [Cancel].
34 ENGLISH
EN_DDX2018ST_KR.indb 34 2017/05/17 9:28

Bluetooth®
Pairing a Bluetooth device using a PIN code (for • If a PIN code is required, enter “0000” (initial) or 3 Select the device (1) to connect, then
Bluetooth 2.0) new PIN code you have entered in step 2.
return to the <Paired Device List> (2).
• When pairing is completed, the device is
1 Display the <PIN Code Set> screen.
registered on the <Paired Device List> screen. BT Connection Settings
On the Home screen, touch as follows: Device Name
Connected ON OFF
Note
Connect Ready ON OFF
• The PIN code is initially set to “0000”.
• The maximum number of digits in the PIN code is 15.
[System] → <Bluetooth Setup> : [Enter]
Connecting/disconnecting a registered
On the <Bluetooth Setup> screen, touch as Bluetooth device
follows: Select [ON] (to connect) or [OFF] (to disconnect).
<PIN Code> : [0000] 1 Display the <Paired Device List> screen. : Mobile phone
On the Home screen, touch as follows: : Audio device
2 Change the PIN code.
If you wish to skip changing the PIN code, go to 4 Connect the selected device.
step 3. Paired Device List
PIN Code Set Device Name 1
0000 Device Name 2
[System] → <Bluetooth Setup> : [Enter]
1 2 3 Device Name 3 OK
4 5 6 On the <Bluetooth Setup> screen, touch as Device Name 4 Connection
7 8 9 follows: Device Name 5 Remove
0 Enter Clear <Paired Device List> : [Enter]

2 Select the device (1) you want to connect, • The status is shown as follows:
then select [Connection] (2). – <Connecting>: Connection is in progress.
• To delete the last entry, touch [Clear]. – <Connected>: A connection has been established.
• To delete the PIN code, touch and hold [Clear]. Paired Device List
– <Connect Ready>: A connection can be
Device Name 1
3 Search for the unit (“DDX3eX”/“DDX3”/ established.
Device Name 2
“DDX4”) from your Bluetooth device. – <Disconnecting>: Disconnection is in progress.
Device Name 3 OK
– <Disconnected>: No connection is established.
Device Name 4 Connection
4 Select the unit (“DDX3eX”/“DDX3”/
Device Name 5 Remove
• When a Bluetooth mobile phone is connected, the
“DDX4”) on your Bluetooth device. signal strength and battery level are displayed when
the information is acquired from the device.
ENGLISH 35
EN_DDX2018ST_KR.indb 35 2017/05/17 9:28

Bluetooth®
To delete the registered device: Perform step 1,
select the device you want to delete in step 2, then
During a call... Making a call
touch [Remove]. 1
Device Name 1
2
Device Name 2 1 Display the phone control screen.
• A confirmation message appears. Touch [Yes]. Talking... Name On the Home screen, touch as follows:
1234XXXXXX
NR LEVEL – 0 +
Bluetooth mobile phone EC LEVEL – 0 +
When a call comes in... DTMF MIC LEVEL – 0 +
1
Device Name 1
2
Device Name 2
2 Select a method to make a call.
Incoming Call Touching the operation keys performs the following 1
Device Name 1
2
Device Name 2
actions: 1234XXXXXX X
Name
1234XXXXXX Ends a call. 1 2 3
[ ]
4 5 6
[ ]/ Switches between handsfree mode and 7 8 9

phone mode. * 0/+ #
[ ]
Touching the operation keys performs the following [DTMF] Enters DTMF (Dual Tone Multi
actions: Frequency), then sends text using the 1 From the call history* (missed calls/received
keypad. calls/dialed calls)
[ ] Answers a call.
NR LEVEL Adjusts the noise reduction level. 2 From the phone book*
[ ] Rejects a call. [–] / [+] (–5 to 5, initial 0) 3 From the preset list (Page 38)
4 Use direct number entry
• Call information is displayed if acquired. EC LEVEL Adjusts the echo volume level.
5 Use voice dialling
• Phone operation is not available while the picture [–] / [+] (–5 to 5, initial 0)
from the rear view camera is displayed. * Applicable only for mobile phone compatible with PBAP (Phone
MIC LEVEL Adjusts the volume level of the
Book Access Profile).
[–] / [+] microphone. (–10 to 10, initial –4)
• Press + / – buttons on the monitor panel to adjust
the volume of the call or earpiece.
36 ENGLISH
EN_DDX2018ST_KR.indb 36 2017/05/17 9:28

Bluetooth®
3 Select a contact (1), then make a call (2). When item 4 is selected in step 2:
Switching between two connected devices
When item 1, 2 or 3 is selected in step 2: Enter the phone number (1), then make a You can change the device to use when 2 devices are
1
Device Name 1
2
Device Name 2 call (2). connected.
Name 1 1 2
1234XXXXXX Device Name 1 Device Name 2 On the phone control screen:
Name 2
2345XXXXXX 1234XXXXXX X
1 2
Device Name 1 Device Name 2
Name 3
3456XXXXXX 1 2 3
A-Z 1234XXXXXX X
Name 4 4 5 6
4567XXXXXX
7 8 9 1 2 3
Name 5
8901XXXXXX * 0/+ # 4 5 6
7 8 9
To use alphabet search in the phone book * 0/+ #
1 Touch [ A-Z ]. • To enter “+”, touch and hold [0/+].
2 Touch the first letter you want to search for on • To delete the last entry, touch [ X ].
the keypad. The active device is highlighted.
To search for a number, touch [1,2,3...]. When item 5 is selected in step 2:
3 Select a contact you want call from the list. Say the name of the person you want to
To display other phone numbers in the same call.
contact • Available only when the connected mobile
You can store up to 10 phone numbers per phone has a voice recognition system.
contact. • If the unit cannot find the target, “Please speak
1 Touch [ ]. into the microphone” appears. Touch [Start],
2 Select a contact you want call from the list. then say the name again.
• To cancel voice dialling, touch [Cancel].
ENGLISH 37
EN_DDX2018ST_KR.indb 37 2017/05/17 9:28

Bluetooth®
1 Tag data* (current track title/artist name/album
Presetting phone numbers Bluetooth audio player
title)
You can preset up to five phone numbers. • Pressing [<] scrolls the text if not all of the text is
1 Display the phone control screen.
KENWOOD Music Mix shown.
On the Home screen, touch as follows: When “BT Audio” is selected as the source, you can 2 Signal strength and battery level
connect up to five Bluetooth audio devices at the (Appear only when the information is acquired
same time. You can easily switch between these five from the device.)
devices by playing music from the device. 3 Playing time*/playback status*
4 Connected device name
2 Select call history or phone book calling • Touching the device name switches to another
connected Bluetooth audio device.
method (1), then select a contact (2) to
preset. * Available only for devices compatible with AVRCP 1.3.
1 2
Name 1 Playback information and key operation

1234XXXXXX
Name 2 • For playback information, see “Source control screen”
2345XXXXXX
Name 3 on page 8.
3456XXXXXX
Name 4
A-Z • For key operations on the touch panel, see “Common
4567XXXXXX operation keys on source control screen” on
Name 5
8901XXXXXX page 8.
BT Audio
3 Select a preset number to store into. Additional keys operations. Touching the operation
1 2
keys performs the following actions:
1234XXXXXX [ ] Displays <Bluetooth Setup> screen.

2345XXXXXX
3456XXXXXX
No preset
No preset
(Hold)
To delete the contact in the preset number: Touch
[ ] besides the contact on the preset list.
38 ENGLISH
EN_DDX2018ST_KR.indb 38 2017/05/17 9:28

Bluetooth®
Selecting an audio file from the menu Bluetooth settings <Auto Connect>
• ON (Initial): Automatically establishes a
1 Display the audio menu. You can change various settings for using Bluetooth connection with the last connected Bluetooth
On the source control screen, touch as follows: devices on the <Bluetooth Setup> screen. device when the unit is turned on.
1 Display the <Bluetooth Setup> screen. • OFF: Cancels.
On the Home screen, touch as follows: <Bluetooth HF/Audio>
Select the speakers used for Bluetooth mobile
2 Select a category (1), then select a phones and Bluetooth audio players.
desired item (2). • Front Only: Front speakers only.
Then, on the <Setup> screen, touch as follows: • All (Initial): All speakers.
BT Audio
[System] → <Bluetooth Setup> : [Enter] <Auto Response>
Playlists
• ON: The unit answers the incoming calls
Artist 2 Make the settings.
automatically in 5 seconds.
Album
Bluetooth Setup • OFF (Initial): The unit does not answer the calls
Songs
Paired Device List Enter automatically. Answer the calls manually.
Genre
PIN Code 0000
Device Name DDX3eX <Auto Pairing>
Device Address 01:20:03:40:05:60:07 • ON (Initial): Establishes pairing automatically
Auto Connect ON OFF with the Android or iOS device (such as iPhone)
BT Audio
Bluetooth HF/Audio Front Only All
connected via USB. (Auto pairing may not work
Artist 1
for some devices depending on the Android/iOS
Artist 2
Artist 3
<Paired Device List> version.)
Artist 4 Display the list of registered devices. You can • OFF: Cancels.
Artist 5 connect a device or delete registered devices. <Initialize>
<PIN Code> Touch and hold [Enter] to reset all settings you
Change the PIN code of the unit. have made for using Bluetooth mobile phones and
Select an item in each layer until you reach and
<Device Name> Bluetooth audio players.
select the desired file.
Show the device name of this unit to
be shown on the Bluetooth device —
“DDX3eX”/“DDX3”/“DDX4”.
<Device Address>
Show the device address of the unit.
ENGLISH 39
EN_DDX2018ST_KR.indb 39 2017/05/17 9:28

Settings
Audio settings <Equalizer> Store your own sound adjustments
The following adjustments are memorized for each
Display the <Audio> screen. source until you adjust the sound again. If the source 1 Select a preset sound mode.
On the Home screen, touch as follows: is a disc, the adjustments are stored for each of the 2 Select a band (1) and adjust the level (2),
following categories. then adjust the sound (3).
• DVD/VCD
Equalizer SRC Name
• CD
Preset Natural Q factor 1.5
Then, on the <Setup> screen, touch [Audio]. • DivX*1/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC [dB]
+9
+7
Setup You cannot adjust the sound when the unit is in +5

+3
0
-3
Audio Equalizer Enter

standby. -5
-7
-9
62.5 100 160 250 400 630 1k 1.6k 2.5k 4k 6.3k 10k 16k [Hz]
Display Sound Effect Enter
Bass EXT ON OFF EQ INT
Input Fader / Balance Enter Selecting a preset sound mode SW LEVEL 0 ALL SRC
System Speaker / X’over Enter
Select a preset sound mode on the <Equalizer>
Time Alignment Enter
screen.
• Natural (Initial)/Rock/Pops/Easy/Top40/Jazz/ Adjust the sound as follows:
E.g. Audio settings screen for DDX395 Powerful/User
<Q factor>
You cannot change the <Audio> screen in the Equalizer SRC Name
Adjusts the width of the frequency.
Preset Natural Q factor 1.5
following situations: [dB] • 1.35/1.5 (Initial)/2.0
+9
• When the AV source is turned off. +7

+5
+3
<Bass EXT>
0
• When the Bluetooth phone is used (making or -3
-5
-7 Activates/deactivates bass.
-9
receiving a call, during a call, or while voice dialling). 62.5 100 160 250 400 630 1k 1.6k 2.5k 4k 6.3k 10k 16k [Hz]
• ON/OFF (Initial)
Bass EXT ON OFF EQ INT
SW LEVEL 0 ALL SRC <SW LEVEL>
Adjusts the subwoofer level.*2
• To apply the adjusted equalizer to all playback
• –50 to +10 (Initial: 0)
sources, touch [ALL SRC], then touch [OK] to
confirm. • To clear the adjustment, touch [EQ INIT].
3 Repeat step 2 to adjust the level of other
bands.
*1 Only for DDX418BT.
*2 Not adjustable when <None> is selected for subwoofer on the
<Speaker Select> screen. (Page 41)
40 ENGLISH
EN_DDX2018ST_KR.indb 40 2017/05/17 9:28

Settings
<Sound Effect> *1 You cannot change the setting when “Radio” is selected as the <Speaker/X’over>
source.
Adjust the sound effect. Setting the speakers and crossover
*2 This function works only when “DISC”/ “USB”/ “iPod”/
<Loudness>
“Android™” is selected as the source. frequency
Adjusts loudness.
• OFF (Initial)/Low/High 1 Select a car type (1), select the location
<Fader/Balance> of the speakers (2), then display the
<Bass Boost>
Selects the bass boost level. Touch [J]/[K]/[H]/[I] or drag the mark to adjust. <Speaker Select> screen (3).
• OFF (Initial)/Level 1/Level 2/Level 3/Level 4/ <Fader>
Level 5 Adjusts the front and rear speaker output balance.
<Drive Equalizer> When using a two-speaker system, set the fader to the
Reduces the driving noise by raising the bandwidth. center (0).
• OFF (Initial)/ON • F15 to R15 (Initial: 0)
<Space Enhancer>*1 <Balance>

Virtually enhances the sound space using the Digital Adjusts the left and right speaker output balance.
Signal Processor (DSP) system. Select the enhance • L15 to R15 (Initial: 0)
level. To clear the adjustment: Touch [Center]. 2 Select the speaker type (1), select the size
• OFF (Initial)/Small/Medium/Large of the selected speaker (2), then display
<Supreme>*2 the <X’over> screen (3).
Restores the sound lost due to audio compression to a
realistic sound.
• OFF/ON (Initial)
<Realizer>
Virtually makes the sound more realistic using the
Digital Signal Processor (DSP) system. Select the sound
level.
• OFF (Initial)/Level 1/Level 2/Level 3
• If a speaker is not connected, select <None>.
<Stage EQ>
• When setting the front speakers, also select the
Moves the center of the sound to the lower or higher
speaker size for <Tweeter>.
point. Select the height.
• OFF (Initial)/Low/Middle/High
ENGLISH 41
EN_DDX2018ST_KR.indb 41 2017/05/17 9:28

Settings
3 Adjust the crossover frequency of the <Time Alignment> Determining the value for <Position DTA>
selected speaker. Make fine adjustments to the delay time of the speaker adjustment
• Adjustable items vary depending on the selected output to create a more suitable environment for your If you specify the distance from the center of the
speaker type/speaker size/crossover settings. car. currently set listening position to every speaker, the
Select the listening position (1), select delay time will be automatically computed and set.
<TW Gain (L)>/<TW Gain (R)> 1 Determine the center of the currently set
Adjusts the output volume of the tweeter (left/ [Distance] or [Gain](2) to make an
listening position as the reference point.
right). adjustment , then adjust each speaker
2 Measure the distances from the reference point
<TW FREQ> setting (3).
to the speakers.
Adjusts the crossover frequency for the tweeter. 3 Calculate the differences between the distance of
<Gain> the furthest speaker and other speakers.
Adjusts the output volume of the selected speaker. 4 Set the DTA value calculated in step 3 for
<HPF FREQ> individual speakers.
Adjusts the crossover frequency for the front or rear 5 Adjust gain for individual speakers.
speakers (high pass filter).
E.g. When <Front All> is selected as the listening
<LPF FREQ> position
Adjusts the crossover frequency for the speaker 1 Select from <All>, <Front L>, <Front R> or
(low pass filter). <Front All>.
2 Select an item to adjust. +3.5 ft
<Slope>
Adjusts the crossover slope. [Distance] Adjusts the digital time alignment
<Phase> value.
Selects the phase for the speaker. [Gain] Adjusts the output volume of the 1.4 ft
selected speaker.
2.45 ft
3 To determine the adjustment value, see the
4.9 ft +2.45 ft
following “Determining the value for <Position
DTA> adjustment”.
To initialize the setting value: Touch [Initialize].
+0 ft
42 ENGLISH
EN_DDX2018ST_KR.indb 42 2017/05/17 9:28

Settings
<Volume Offset> <Dimmer> Only for DDX395/DDX375BT/DDX418BT:
<Panel Color>: Change the illumination color of the
Adjust and store the auto-adjustment volume level for • Auto (Initial): Dims the screen and button
buttons on the monitor panel.
each source. If the source is a disc, the adjustment is illumination when you turn on the headlights.
stored for each of the following categories: – The ILLUMI lead connection is required.
• DVD/VCD (Page 56)
• CD • ON: Activates dimmer.
• DivX*/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC • OFF: Deactivates dimmer.
Scan
The volume level will automatically increase or
decrease when you change the source. <User Customize>
• –15 to +6 (Initial: 00)
You can change the display design. While playing a
video or picture, you can capture an image and use • You can also adjust the illumination color yourself.
* Only for DDX418BT. Touch [Edit] to display the illumination color
the captured image as a background.
• You cannot capture copyrighted content and images adjustment screen, then select the dimmer setting
Display settings from iPod/iPhone. and adjust the color. The adjustment is saved in
• When using a JPEG file as the background, make sure [User].
Display the <Display> screen. that the resolution is 800 x 480 pixels. • Selecting [Scan] changes the illumination color
On the Home screen, touch as follows: • The color of the captured image may look different gradually.
from that of the actual scene.
Storing your own scene for the background
<Background>: Change the background design.
image
Then, on the <Setup> screen, touch [Display].
Setup
1 While playing a video or picture, display
Audio Dimmer Auto
the <User Customize> screen.
Display User Customize Enter
On the <Display> screen, touch as follows:
Input OSD Clock ON OFF
<User Customize>: [Enter]
System Demonstration ON OFF 2 Display the background design selection
Scroll ON Once OFF
screen, then touch [ Capture].
E.g. Display settings screen for DDX395
ENGLISH 43
EN_DDX2018ST_KR.indb 43 2017/05/17 9:28

Settings
3 Adjust the image (1), then capture the <Demonstration> <Screen Adjustment>
image (2). • ON (Initial): Activates the display demonstration. Adjust the brightness and blackness of the screen.
• OFF: Deactivates the display demonstration. Select [DIM ON] (dimmer on) or [DIM OFF] (dimmer
off), then change the following settings:
<Scroll> <Bright>
• ON (Initial): Scrolls the displayed information Adjusts brightness.
repeatedly. • –15 to +15 (Initial: 0 for dimmer on, +15 for dimmer
Capture Cancel
• Once: Scrolls the displayed information once. off)
• OFF: Cancels. <Black>
Touching [<] scrolls the text regardless of this setting. Adjusts blackness.
E.g. Image adjustment screen for DDX395
• –10 to +10 (Initial: 0)
[J][K][H][I] Moves the zooming frame. <Home Customize>
Magnifies the scene. Arrange the items to display on the Home screen. <Video Output>
[ ] • <OFF>/<Zoom1>/<Zoom2>/ Select the color system of the external monitor.
<Zoom3> Select an item (1) to replace, then select the • NTSC (Initial)/PAL
[IW]* Starts/pauses playback.
item (2) you want to display in the selected
position. “Please Power Off” appears when the setting is
[ ]* Advances scenes frame by frame. Repeat this step to place icons for other items. changed. Turn off the power, then turn on to enable
• Only selectable sources are shown. the change.
A confirmation message appears. Touch [Yes]
to store the newly captured image. (The existing Pandora <Viewing Angle>
HOME
image is replaced with the new one.) Customize
• To return to the previous screen, touch [No]. Select the viewing angle in relation to the monitor
• To cancel the capture, touch [Cancel]. panel to make the panel easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
* Not displayed when playing an external component connected to
the AV-IN input terminal (for DDX418BT only). iPod TEL R di
Radio
<OSD Clock> E.g. Home customize screen for DDX395

• ON: Displays the clock while a video source is
playing.
• OFF (Initial): Cancels.
44 ENGLISH
EN_DDX2018ST_KR.indb 44 2017/05/17 9:28

Settings
<Guidelines Setup> <Parking Assist Position>
Input settings
Adjust the parking guidelines according to the size of Select where information about obstacles is displayed
Display the <Input> screen. the car, parking space and so on. on the screen.
On the Home screen, touch as follows: When adjusting the parking guidelines, make sure to • Left/Right (Initial)
use the parking brake to prevent the car from moving.
Select the mark (1), then adjust the position of the System settings
selected mark (2).
Then, on the <Setup> screen, touch [Input]. Display the <System> screen.
On the Home screen, touch as follows:
Setup
Audio Rear Camera Enter
Display Parking Assist Enter
Input
System Then, on the <Setup> screen, touch [System].
Initialize
Setup
Audio Language English
Display Clock Enter
E.g. Input settings screen for DDX395 Make sure that A and B are horizontally parallel, and
Input Smartphone Setup Enter
that C and D are the same length.
System Bluetooth Setup Enter
<Rear Camera> • Touch and hold [Initialize ] for 2 seconds to set all Maestro Setup Enter
Configure the rear view camera settings. the marks to the initial default position.
<Rear Camera Interruption>
E.g. System settings screen for DDX395
• ON: Displays the picture from the rear view camera <Parking Assist>
when you shift the gear to the reverse (R) position. (Only for DDX395/DDX375BT)
– A caution message appears on the screen. To <Language>
Configure settings for using the ADS adapter. Select the text language used for on-screen
remove the caution message, touch the screen.
• OFF (Initial): Select this when no camera is <Parking Assist Display> information. For details, see “Initial settings” on
connected. When an ADS adapter is connected, you can display page 5.
information about obstacles around the car.
<Parking Guidelines>
• ON: Always displays information. <Clock>
• ON (Initial): Displays the parking guidelines.
• Dyn. (Initial): Displays information when the sensor
• OFF: Hides the parking guidelines. Set the clock. For details, see “Clock settings” on
detects obstacles.
page 6.
• OFF: Cancels.
ENGLISH 45
EN_DDX2018ST_KR.indb 45 2017/05/17 9:28

Settings
<Smartphone Setup> [USB 1 Wire] Select this when the device is <Bluetooth Setup>
Specify the connection method of Android/iPod/ connected via the USB input Configure settings for using a Bluetooth device, such
iPhone. terminal (cable from the rear as connection and other general operations. For
panel). details, see “Bluetooth settings” on page 39.
1 Select the device type (1), then touch
[Bluetooth] Select this when the device is
[Change] (2).
connected via Bluetooth. (Go to <OEM Setup>
Smartphone Setup step 3.)
Initial Information
Device Type iPod / iPhone
If [Android/Other] is selected in step 1: Get information, and change the settings for using the
Connection Type Bluetooth
Device Name Device Name Smartphone Setup ADS adapter.

Device Type Select Bluetooth
iPod / iPhone Android / Other Change
<Beep>
• ON (Initial): Activates the key-touch tone.
• OFF: Deactivates the key-touch tone.
2 Select the connection method (1), then Next
confirm the selection ([OK] or [Next]) (2). <SETUP Memory>

If [iPod/iPhone] is selected in step 1: The <Paired Device List> screen appears. Go to
Memorize, recall, or clear the settings you have made.
Smartphone Setup step 3.
• The memorized settings are kept even when the unit
USB 1 Wire Bluetooth
3 When selecting [Bluetooth] as the is reset.
connection method: Select the device (1), Touch [Yes] to display the setting screen, then select
then press [OK] (2) to connect. an operation:
OK • If the device is already connected, skip step 1. • Recall: Recalls the memorized settings.
Paired Device List • Memory: Memorizes the current settings.
Device Name 1
• Clear: Clears the currently memorized settings.
Device Name 2 • Cancel: Cancels.
Device Name 3 OK
A confirmation message appears. Touch [Yes].
Device Name 4 Connection
Device Name 5 Remove
46 ENGLISH
EN_DDX2018ST_KR.indb 46 2017/05/17 9:28

Settings
<DivX(R) VOD> <Touch Panel Adjust> 2 Press and hold a button on the steering
(Only for DDX418BT) Adjust the touch positions of the buttons on the remote controller to register or change.
screen.
This unit has its own Registration Code. Once you 3 Select a function to assign to the selected
have played back a file with the Registration Code Touch the center of the marks at the upper left (1), button.
recorded, this unit’s Registration Code is overwritten the lower center (2), then the upper right (3) as
Sterring Remote Control Setting
for copyright protection. instructed. Please select the function to assign to the button.
• Touch [Enter] to display the information. Touch Panel Adjust VOL

• To return to the previous screen, touch [OK]. VOL
ATT
Done SRC
<Security Code>
(Only for DDX418BT)
Register the security code for the unit. (Page 6) Cancel Reset 4 Repeat steps 2 and 3 to register other
buttons.
<SI> • To reset the touch position, touch [Reset].
Activate or deactivate the security function. • To cancel the current operation, touch [Cancel].
5 Touch [Done] to finish procedure.
(Page 6) • The unit can register/change all of the buttons’
<Steering Remote Control Setting> functions at the same time. To do this, press all
<Serial Number> buttons in turn and after pressing all of them, touch
(Only for DDX418BT)
[Done] on the <Steering Remote Control Setting>
(Only for DDX395/DDX375BT/DDX25BT) Assign functions to the keys of the remote controller screen. However, new functions cannot be learned
Displays the serial number. on the steering wheel. after this operation.
• This function is available only when your car is • When changing the functions already learned, touch
equipped with the electrical steering remote the assigned function you want to change in step 3
controller. and then touch to select the new function from the
• You can only register/change the functions while function list.
you are parked. • Confirm the contents of the settable functions in the
• If your steering remote controller is not compatible, function list. You cannot edit the function list.
learning may not be completed and an error
To initialize the setting: Touch [Initialize] for
message may appear.
<Steering Remote Control Setting>.
1 Touch [Set] for <Steering Remote Control • A confirmation message appears. Touch [Yes].
Setting> to display the setting screen. – To cancel the initialization, touch [No].
ENGLISH 47
EN_DDX2018ST_KR.indb 47 2017/05/17 9:28

Settings Remote Controller
<System Information> • For DDX418BT: This unit can be operated using the
remote controller (RC-DV340) supplied with this unit.
CAUTION
Update the system by connecting a USB device • Put the Remote Controller in a place where it will
• For DDX395/DDX375BT/DDX350BT/DDX25BT:
containing an update file. not move during braking or other operations. A
Optional remote controller KNA-RCDV331 is
• To obtain the update file, visit dangerous situation could result if the Remote
designed for controlling this unit. Refer to the
<www.kenwood.com/cs/ce/>. Controller falls down and gets wedged under the
instruction manual that comes with the remote
Connect a USB device with the update file to the unit. controller. pedals while driving.
• Do not leave the battery near fire or under direct
Remote sensor* sunlight. A fire, explosion or excessive heat
generation may result.
• Do not recharge, short, break up or heat the battery,
or place it in an open fire. Such actions may cause
the battery to leak fluid. If spilled fluid comes in
contact with your eyes or clothing, immediately rinse
<Application Version>
with water and consult a physician.
Updates the system application.
• Place the battery out of reach of children. In the
<System Version> unlikely event that a child swallows the battery,
Updates the system. * DO NOT expose the remote sensor to bright immediately consult a physician.
<DVD Version> light (direct sunlight or artificial lighting).
Updates the DVD system application.
The system update starts. It may take a while.
If the update has been completed successfully,
“Update Completed” appears, then reset the unit.
• Do not disconnect the USB device while updating.
• If the update has failed, turn the power off and then
on, and retry the update.
RC-DV340
• Even if you have turned off the power during the
update, you can restart the update after the power
is turned on. The update will be performed from the
beginning.
<Open Source Licenses>

Shows the Open Source Licenses.
48 ENGLISH
EN_DDX2018ST_KR.indb 48 2017/05/17 9:28

Remote Controller
Preparation Remote Controller mode switch Basic operations for RC-DV340 (supplied)
The functions operated from the remote controller
Battery installation differ depending on the position of the mode switch.
Common operations (AUD mode)
Use two “AAA”/“R03”-size
SRC • Selects the source.
batteries.
• Hangs up the incoming/current call.
Insert the batteries with the + AUD
and – poles aligned properly, t
DVD t
J/K VOL Adjusts the volume level.
AUDt
following the illustration inside DVDt TV t ATT Attenuates/restores the sound.
T Vt t
the case. NAV
• Always insert batteries from DISP/V.SEL Switches to the current source control
– poles to avoid bending the screen.
• AUD mode: Switch to this mode when controlling a ENTER Enters options.
springs.
selected source or tuner source, etc.
• If the Remote Controller Answers incoming calls.
• DVD mode: Switch to this mode when playing DVDs
operates only over shorter distances or does not
or CDs etc. with the player integrated in this unit. FNC/PBC/ Switches the control screen.
operate at all, it is possible that the batteries are
• TV mode: Not used. MENU
depleted. In such instances, replace both batteries
• NAV mode: Not used.
with new ones. MODE/TOP Changes the aspect ratio.
• The position of the remote control mode switch is
MENU • The aspect ratio changes each time
indicated in the title of each mode, e.g., “AUD mode”.
you press this key.
• When controlling a player that is not integrated in
the unit, select “AUD” mode. OPEN Not used for this unit.
ENGLISH 49
EN_DDX2018ST_KR.indb 49 2017/05/17 9:28

Remote Controller
DVD/VCD (DVD mode) DIRECT Enters direct search mode. iPod/Android (AUD mode)
CLEAR Deletes a character while in direct
J/K/H/I Moves the cursor when displaying a S/T Selects music/videos.
search mode.
menu.
I/W Starts/pauses playback.
S/T Selects a track.
I/W Starts/pauses playback.
Music Disc/Audio file/Video file/Picture file
(AUD mode) USB (AUD mode)
o Stops and memorizes the point
where the disc stops. AM –/FM + Selects a folder. AM –/FM + Selects a folder.
0–9 • Specifies the number to search for S/T Selects a track/file. S/T Selects a file.
in direct search.
• 1/2: Fast forwards/backwards. I/W Starts/pauses playback. I/W Starts/pauses playback.
– Fast forward/backward speed 0–9 Specifies the number to search for in
changes each time you press this direct search.
key. Searching for an item directly
DIRECT Enters direct search mode.
• 4/5: Slow forwards/backwards While listening to the radio or during disc playback,
during pause. you can search for a station frequency/chapter/title/
folder/file/track directly using the number buttons.
MODE/TOP Shows the disc top menu. Radio/SiriusXM*1 (AUD mode) • To search for a track from the VCD menu, perform
MENU
AM –/FM + Selects the band. during PBC playback.
FNC/PBC/ Shows the disc menu.
MENU S/T Searches for stations.*2 1 Press DIRECT to enter the search mode.
SUBTITLE Changes the subtitle language. • Each time you press DIRECT, the item to search
I/W Changes the seek mode (AUTO1, for changes.
ZOOM Changes the zoom ratio. AUTO2, MANU).
• The zoom ratio changes each time 0–9 • Specifies preset number. (1-5) 2 Press a number button to select a desired
you press this key. • Specifies the frequency of the item (station frequency/chapter/title/
ANGLE Changes the picture angle. station to receive to search for in folder/file/track).
• The picture angle changes each direct search. • To erase a misentry, press CLEAR.
time you press this key. DIRECT Enters direct search mode. 3 Confirm the selection.
AUDIO Changes the voice language. • For station frequency: Press S/T.
*1 Only for DDX395/DDX375BT/DDX25BT.
• The voice language changes each • For others: Press ENTER.
*2 The search method differs according to the selected seek mode.
time you press this key. To exit the search mode: Press DIRECT.
50 ENGLISH
EN_DDX2018ST_KR.indb 50 2017/05/17 9:28

Remote Controller
Basic operations for KNA-RCDV331 MAP DIR/OPEN Not used for this unit. * +/CLEAR Deletes a character while in direct
(optionally purchased) search mode.
NAV/DISP Not used for this unit.
# BS/DIRECT Enters direct search mode.
ZOOM OUT/IN Not used for this unit.
ROUTE M/ Shows the disc top menu.
2 ZONE Not used for this unit.
MODE/
R.VOL Not used for this unit. TOP MENU
VOICE/FNC/ • Shows the disc menu.
* Available only when the AUD mode is selected. MENU/PBC • Turns the playback control on or
off while playing VCD.
DVD/VCD (DVD mode) CANCEL/ Displays previous screen.
RETURN
J/K/H/I Moves the cursor when displaying
a menu. AUDIO Changes the voice language.
• The voice language changes
H/S / T/I Selects a track.
each time you press this key.
J/FM+ / K/AM− Selects a folder.
Common operations (AUD/DVD mode) SUBTITLE Changes the subtitle language.
POSITION/IW Starts/pauses playback.
ANGLE Changes the picture angle.
SRC* • Selects the source. MENU/o Stops and memorizes the point • The picture angle changes each
• Hangs up the incoming/current where the disc stops. time you press this key.
call.
0–9 • Specifies the number to search ZOOM Changes the zoom ratio.
VOL J/K Adjusts the volume level. for in direct search. • The zoom ratio changes each
ATT Attenuates/restores the sound. • 1/2: Fast forwards/backwards. time you press this key.
• 4/5: Slow forwards/backwards.
VOICE/FNC/ For discs/USB/iPod: Switches to the
(For DVD only)
MENU/PBC* current source control screen.
– Slow forward/backward speed
ENTER Enters options. changes each time you press
Answers incoming calls. this key.
ROUTE M/ Changes the aspect ratio.

MODE/ • The aspect ratio changes each
TOP MENU* time you press this key.
VIEW/AV OUT Switches the AV source to be
output.
ENGLISH 51
EN_DDX2018ST_KR.indb 51 2017/05/17 9:28

Remote Controller
Music Disc/Audio file/Video file/Picture file iPod/Android (AUD mode) Searching for an item directly
(AUD mode) While listening to the radio or during disc playback,
H/S / T/I Selects music/videos.
you can search for a station frequency/chapter/title/
J/FM+ / K/AM− Selects a folder. POSITION/IW Starts/pauses playback. folder/file/track directly using the number buttons.
H/S / T/I Selects a track/file. • To search for a track from the VCD menu, perform
during PBC playback.
POSITION/IW Starts/pauses playback. USB (AUD mode)
0–9 Specifies the number to search for
1 Press # BS/DIRECT to enter the search
in direct search. J/FM+ / K/AM− Selects a folder. mode.
• Each time you press # BS/DIRECT, the item to
# BS/DIRECT Enters direct search mode. H/S / T/I Selects a file.
search for changes.
POSITION/IW Starts/pauses playback.
2 Press a number button to select a desired
Radio/SiriusXM*1 (AUD mode) item (station frequency/chapter/title/
folder/file/track).
J/FM+ / K/AM− Selects the band. • To erase a misentry, press * +/CLEAR.
H/S / T/I Searches for stations.*2 3 Confirm the selection.
POSITION/IW Changes the seek mode (AUTO1, • For station frequency: Press H/S / T/I.
AUTO2, MANU). • For others: Press ENTER.
0–9 Specifies the frequency of the To exit the search mode: Press # BS/DIRECT.
station to receive to search for in
direct search.
# BS/DIRECT Enters direct search mode.
*1 Only for DDX395/DDX375BT/DDX25BT.

*2 The search method differs according to the selected seek mode.
52 ENGLISH
EN_DDX2018ST_KR.indb 52 2017/05/17 9:28

Remote Controller Installation and Connection
KENWOOD Remote APP WARNINGS Before installation
KENWOOD Remote is an application that connects • DO NOT connect the ignition wire (red) and the
and controls compatible KENWOOD car receivers via
Precautions on installation and connection
battery wire (yellow) to the car chassis (ground), you
Bluetooth® like a wireless remote control. may cause a short circuit, that in turn may start a fire. • Mounting and wiring this product requires skills and
• DO NOT cut out the fuse from the ignition wire (red) experience. For best safety, leave the mounting and
You can also operate this unit from a Smartphone wiring work to professionals.
using KENWOOD Remote APP. and the battery wire (yellow). The power supply must
be connected to the wires via the fuse. • Mount the unit so that the mounting angle is 30° or
This application can display the source information less.
of this unit on the smartphone’s screen, and enables • Always connect the ignition wire (red) and the
battery wire (yellow) to the power source running • Make sure to ground the unit to a negative 12 V DC
the user to make an audio setting using the graphic power supply.
user interface of this application. through the fuse box.
• Do not install the unit in a location exposed to direct
This application also works as a free standalone sunlight or excessive heat or humidity. Also avoid
music player application, when your Smartphone is CAUTIONS places with too much dust or the possibility of water
not connected to this unit. • Install this unit in the console of your car. splashing.
• For details, visit <www.kenwood.com/car/app/ • Do not touch the metal parts of this unit during and • Do not use your own screws. Use only the screws
kenwood_remote/eng/>. shortly after the use of the unit. Metal parts such as provided. If you use the wrong screws, you could
the heat sink and enclosure become hot. damage the unit.
• When parking at a low ceiling area, turn off the unit • After the unit is installed, check whether the brake
to store the antenna. As when the unit is installed in lamps, blinkers, wipers, etc. on the car are working
the car with the function of auto antenna; the radio properly.
antenna extends automatically when you turn on • Do not press hard on the panel surface when
the unit with the antenna control wire (ANT. CONT) installing the unit to the car. Otherwise scratches,
connected. (Page 56) damage, or failure may result.
• If the power is not turned on (“Miswiring DC Offset
Error”, “Warning DC Offset Error” is displayed),
the speaker wire may have a short circuit or have
touched the chassis of the car and the protection
function may have been activated. In this case, the
speaker wire should be checked.
• Keep all cables away from heat dissipating metal
parts.
ENGLISH 53
EN_DDX2018ST_KR.indb 53 2017/05/17 9:28

Installation and Connection
• If your car’s ignition does not have an ACC position,
connect the ignition wires to a power source that
Parts list for installation Installation procedure
Note: This parts list does not include all the package
can be turned on and off with the ignition key. If you
contents.
1 Remove the key from the ignition and
connect the ignition wire to a power source with a disconnect the · battery.
constant voltage supply, such as with battery wires, ¥ Wiring harness (× 1)
the battery may be drained. ø Extension wire, 2 m (× 1) 2 Make the proper input and output wire
• If the fuse blows, first make sure the wires are not π Flat head screws, M5 × 8 mm (× 6) connections for each unit.
touching to cause a short circuit, then replace the old [ Round head screws, M5 x 8 mm (× 6)
“ Microphone, 3 m (× 1) 3 Connect the speaker wires of the wiring
fuse with one with the same rating.
harness.
• Insulate unconnected wires with vinyl tape or other Only for DDX395/DDX418BT
similar material. To prevent a short circuit, do not ] Trim plate (× 1) 4 Connect the wires of the wiring harness
remove the caps and do not let the cable out at the in the following order: ground, battery,
Only for DDX395
ends of the unconnected wires or the terminals. ignition.
‘ Mounting sleeve (× 1)
• Secure the wires with cable clamps and wrap vinyl
tape around the wires that comes into contact with
\ Extraction keys (× 2) 5 Connect the wiring harness to the unit.
metal parts to protect the wires and to prevent short Only for DDX418BT 6 Install the unit in your car.
circuit. « Steering remote cable (× 1) Make sure that the unit is installed securely in place.
• Connect the speaker wires correctly to the terminals Å Audio and video cable (× 1) If the unit is unstable, it may malfunction (e.g., the
to which they correspond. The unit may be damaged sound may skip).
or fail to work if you share the · wires or ground
them to any metal part in the car. 7 Reconnect the · battery.
• When only two speakers are being connected to the 8 Press the reset button on the monitor
system, connect both connectors either to the front panel. (Page 4)
output terminals or to the rear output terminals (do
not mix front and rear). For example, if you connect 9 Configure <Initial Settings>. (Page 5)
the ª connector of the left speaker to a front output
terminal, do not connect the · connector to a rear
output terminal.
54 ENGLISH
EN_DDX2018ST_KR.indb 54 2017/05/17 9:28

Installing the unit Installing the trim plate 2 Remove from the upper two catches of
(Only for DDX395/DDX418BT) the trim plate (]).
Installing the unit using the mounting
bracket removed from the car
π/[ ]
The frame can be removed from the top side in the

π/[ same manner.
Car bracket
3 Remove the unit by inserting the two
Note: Select the appropriate screws (supplied) for the
Removing the unit extraction keys (\), then pulling them as
mounting bracket.
(Only for DDX395) illustrated.
Installing the unit using the mounting
sleeve 1 Engage the catch pins on the extraction
\
keys (\) and remove the two locks on the
(Only for DDX395)
lower part of the trim plate (]).
Catch
‘ Lock
Be careful to avoid injury from the catch pins on

the extraction key.
Bend the tabs of the mounting sleeve with a

screwdriver or similar utensil and attach it in place.
ENGLISH 55
EN_DDX2018ST_KR.indb 55 2017/05/17 9:28

Wiring connection
10 A fuse *1 Only for DDX395/DDX375BT/DDX25BT.
*2 Only for DDX395/DDX375BT.
“ *3 Only for DDX418BT.
*3
Connect the antenna cord to the antenna terminal

*1 *2 *3 USB input terminal (1 m)
Purple with white stripe
REVERSE To the car’s reverse lamp harness when using the optional rear view camera
Light green To the car’s parking brake detection switch harness
¥ PRK SW
Extension wire ( ø ) (For best safety, be sure to connect the parking sensor.)
White ] / White with black stripe [
To front speakers (left)
Gray ] / Gray with black stripe [
To front speakers (right)
Green ] / Green with black stripe [
To rear speakers (left)
Purple ] / Purple with black stripe [
To rear speakers (right)
Brown
MUTE Not used.
Orange with white stripe
ILLUMI To the car light control switch
Light blue with yellow stripe STEERING WHEEL
REMOTE INPUT
REMOTE CONT To the OE remote adapter (not supplied) which is compatible with your car
Blue with white stripe (12 V 350 mA) ANT.CONT To the power control terminal when using the optional power amplifier (Or)
P.CONT
To the control terminal of the motor antenna or to the power terminal for the booster amplifier of film-type antenna
Red (Ignition wire)
Ignition key switch
Yellow (Battery wire) Car fuse
Black (Ground wire)
Car battery
To the car chassis
56 ENGLISH
EN_DDX2018ST_KR.indb 56 2017/05/17 9:28

Installation and Connection References
7 Rear view camera input (R-CAM)
Connecting external components Maintenance
8 Output terminals*5
• Left output (White) Cleaning the unit
• Right output (Red) • Do not use any solvent (for example, thinner,
REAR: Rear speaker preouts benzine, etc.), detergent, or insecticide. This may
FRONT: Front speaker preouts damage the monitor or the unit.
SW: Subwoofer preouts • Gently wipe the panel with a soft, dry cloth.
*1 Only for DDX395/DDX375BT/DDX25BT. Handling discs

*2 Only for DDX395/DDX375BT. • Do not touch the recording surface of the disc.
*3 Only for DDX418BT. • Do not stick tape etc. on the disc, or use a disc with
*4 Use the audio and video cable (Å) to connect an external tape stuck on it.
component. • Do not use any accessories for the disc.
*5 When connecting an external amplifier, connect its ground wire • Clean from the center of the disc and move outward.
to the chassis of the car; otherwise the unit may be damaged. • Clean the disc with a dry silicone or soft cloth. Do not
1 Expansion port for connecting SiriusXM Connect use any solvents.
Vehicle Tuner (EXT I/F) (commercially available)*1 • When removing discs from this unit, pull them out
2 iDatalink input for connecting an ADS adapter horizontally.
(commercially available)*2 • Remove burrs from the center hole and disc edge
3 Steering wheel remote controller input before inserting a disc.
(REMO-IN)*3
• Connect to the car’s steering remote harness
using the steering remote cable («). Contact More information
your KENWOOD dealer for details.
4 Microphone input (MIC) (Page 56)
About playable files
5 Audio video input (AV-IN)*3*4 Audio files
Connect the following type of 4-pole mini plug: • This unit can play back the following files with
13 1 Left audio following codec and extension code:
2 Right audio – For disc: MP3 (.mp3), WMA (.wma), WAV (.wav),
3 Ground AAC (.m4a)
24
4 Composite video – For USB mass storage class device: MP3 (.mp3),
WMA (.wma), WAV (.wav), AAC (.aac, .m4a),
6 Video output (V-OUT)
FLAC (.flac)
ENGLISH 57
EN_DDX2018ST_KR.indb 57 2017/05/17 9:28

References
• This unit can play back files that meet the conditions – AAC files copy-protected with FairPlay (except Picture files
below: those stored on an iPod/iPhone). • This unit can play back the following files with
– Bit rate: – Files which have data such as AIFF, ATRAC3, etc. following codec and extension code:
MP3: 8 kbps – 320 kbps – JPEG (.jpg, .jpeg)
WMA: For disc: 5 kbps – 320 kbps Video files • Other playable conditions:
For USB : 32 kbps – 192 kbps • This unit can play back the following files with – Resolution: 32 × 32 to 8 192 × 7 680 (It may take
AAC: 16 kbps – 320 kbps following codec and extension code: time to display the file depending on its resolution.)
– Sampling frequency: – DivX* (.divx, .div, .avi) regardless of the letter case— – Baseline JPEG files
MP3: 16 kHz – 48 kHz upper/lower • This unit cannot play back the following files:
WMA: 8 kHz – 48 kHz – MPEG1/MPEG2 (.mpg, .mpeg) – Progressive JPEG files
WAV: 44.1 kHz • Streams that conform to: – Lossless JPEG files
AAC: 32 kHz – 48 kHz – DivX*:
FLAC: 8 kHz – 96 kHz Audio: MP3 or Dolby Audio About disc playback
– Files recorded in VBR (variable bit rate), and have a – MPEG1/MPEG2:
Playable disc types
discrepancy in elapsed time indication Audio: MPEG1 Audio Layer-2 or Dolby Audio
• CD-DA: Audio CD, CD Text
• This unit can show or display the following: Video: MPEG system/program stream
• DVD Video: Region code: 1 or 4 (depending on the
– Tag: • Other playable conditions:
country and sales area)
MP3: ID3 Tag (version 1.0/1.1/2.2/2.3/2.4) – Data size: less than 2 GB
• Dual Disc: DVD side
WMA Tag – DivX*: Bit rate: 8 Mbps (maximum for average video
• VCD: Video CD (PBC compatible)
WAV Tag signals)
• DVD Recordable/Rewritable (DVD-R/-RW, +R/+RW)
AAC Tag – MPEG1/MPEG2: File format: MP@ML (Main Profile at
– DVD Video: UDF bridge
FLAC Tag Main Level)/SP@ML (Simple Profile at Main Level)/
– ISO 9660 level 1, level 2, Romeo, Joliet
– Jacket picture: MP@LL (Main Profile at Low Level)
– Other playable formats:
Picture size: 32 × 32 to 1 232 × 672 resolution • This unit cannot play back the following files:
DVD-R recorded in multi-border format (except for
Data size: less than 500 KB – DivX files encoded in the interlaced scanning
dual layer discs)
File type: JPEG mode.
Finalized +R/+RW (Video format only)
• This unit cannot play back the following files: * Only for DDX418BT. • CD Recordable/Rewritable (CD-R/-RW):
– MP3 files encoded with MP3i and MP3 PRO format. – ISO 9660 level 1, level 2, Romeo, Joliet
– MP3 files encoded with Layer 1/2. • Other informations:
– WMA files encoded with lossless, professional, and – While playing a DVD Video, DTS sound cannot be
voice format. reproduced or emitted from this unit.
– WMA files which are not based upon Windows
Media® Audio.
– WMA/AAC files copy-protected with DRM.
58 ENGLISH
04_DDX_2018ST_KR_Body02.indd 58 9/5/2017 5:27:20 PM

References
– This unit can recognize a total of 5 000 files and Language codes (for DVD language selection) LV Latvian, Lettish SM Samoan
250 folders (a maximum of 999 files per folder) in a AA Afar GD Scots Gaelic MG Malagasy SN Shona
recordable/rewritable disc. AB Abkhazian GL Galician MI Maori SO Somali
– Use only “finalized” recordable/rewritable discs. AF Afrikaans GN Guarani MK Macedonian SQ Albanian
– This unit can play back multi-session recordable/ AM Ameharic GU Gujarati ML Malayalam SR Serbian
rewritable discs; however, unclosed sessions will be
AR Arabic HA Hausa MN Mongolian SS Siswati
skipped while playing.
AS Assamese HI Hindi MO Moldavian ST Sesotho
AY Aymara HR Croatian MR Marathi SU Sundanese
Unplayable disc types and formats
• DVD-Audio/DVD-ROM discs AZ Azerbaijani HU Hungarian MS Malay (MAY) SW Swahili
• SVCD (Super Video CD), CD-ROM, CD-I (CD-I Ready), BA Bashkir HY Armenian MT Maltese TA Tamil
DTS-CD BE Byelorussian IA Interlingua MY Burmese TE Telugu
• MPEG4/DivX*/AAC (.aac)/FLAC/MKV/DVD–VR/ BG Bulgarian IE Interlingue NA Nauru TG Tajik
DVD+VR/DVD-RAM recorded on DVD-R/RW or BH Bihari IK Inupiak NE Nepali TH Thai
+R/+RW BI Bislama IN Indonesian NO Norwegian TI Tigrinya
• MPEG4/DivX*/AAC (.aac)/FLAC/MKV recorded on BN Bengali, Bangla IS Icelandic OC Occitan TK Turkmen
CD-R/RW BO Tibetan IW Hebrew OM (Afan) Oromo TL Tagalog
• DVD-RW dual layer discs BR Breton JA Japanese OR Oriya TN Setswana
• +RW double layer discs CA Catalan JI Yiddish PA Panjabi TO Tonga
• Non-DVD side of a “DualDisc” which does not comply CO Corsican JW Javanese PL Polish TR Turkish
with the “Compact Disc Digital Audio” standard CS Czech KA Georgian PS Pashto, Pushto TS Tsonga
• Discs that are not round.
CY Welsh KK Kazakh QU Quechua TT Tatar
• Discs with coloring on the recording surface or discs
DZ Bhutani KL Greenlandic RM Rhaeto-Romance TW Twi
that are dirty.
EL Greek KM Cambodian RN Kirundi UK Ukrainian
• Recordable/Rewritable discs that have not been
finalized. EO Esperanto KN Kannada RO Rumanian UR Urdu
• 3 inch discs. Attempting to insert these discs using ET Estonian KO Korean (KOR) RW Kinyarwanda UZ Uzbek
an adapter may cause a malfunction. EU Basque KS Kashmiri SA Sanskrit VI Vietnamese
• Some recordable/rewritable discs or files may not be FA Persian KU Kurdish SD Sindhi VO Volapuk
played back due to their characteristics or recording FI Finnish KY Kirghiz SG Sangho WO Wolof
conditions. FJ Fiji LA Latin SH Serbo-Croatian XH Xhosa
* Only for DDX395/DDX375BT/DDX350BT/DDX25BT. FO Faroese LN Lingala SI Singhalese YO Yoruba
FY Frisian LO Laothian SK Slovak ZU Zulu
GA Irish LT Lithuanian SL Slovenian
ENGLISH 59
EN_DDX2018ST_KR.indb 59 2017/05/17 9:28

References
• Electrostatic shock at connecting a USB device may iPod/iPhone that can be connected
About USB playback cause abnormal playback of the device. In this case, • Via the USB terminal:
Important disconnect the USB device then reset this unit and Made for
Make sure all important data has been backed up to the USB device. – iPod nano (7th Generation)
avoid losing the data. • Do not pull out and connect the USB device – iPod touch (6th Generation)
We bear no responsibility for any loss of data stored in repeatedly while “Reading” is shown on the screen. – iPod touch (5th Generation)
the devices while using this unit. • Operation and power supply may not work as – iPhone 7 Plus
intended for some USB devices. – iPhone 7
Playable files on a USB device • Do not leave a USB device in the car, or expose to – iPhone SE
• This unit can play the following types of files stored direct sunlight or high temperatures to prevent – iPhone 6S Plus
in a USB mass storage class device. deformation or damage to the device. – iPhone 6S
– JPEG/Divx*/MPEG1/MPEG2/MP3/WMA/WAV/AAC – iPhone 6 Plus
(.aac/.m4a)/FLAC Unplayable USB device – iPhone 6
• This unit can recognize: • This unit may not play back files in a USB device – iPhone 5S
– A total of 5 000 files properly when using a USB extension cable. – iPhone 5C
– 250 folders for video files and a maximum of 999 • USB devices equipped with special functions such as – iPhone 5
files per folder data security functions cannot be used with the unit. – iPhone 4S
– 250 folders for photo files and a maximum of 999 • Do not use a USB device with 2 or more partitions. • Via Bluetooth:
files per folder • Depending on the shape of the USB devices and Made for
– 999 folders for audio files and a maximum of 999 connection ports, some USB devices may not be – iPod touch (6th Generation)
files per folder attached properly or the connection might be loose. – iPod touch (5th Generation)
• The maximum number of characters (when the • This unit may not recognize a memory card inserted – iPhone 7 Plus
characters are 1 byte): into a USB card reader. – iPhone 7
– Folder names: 50 characters – iPhone SE
– File names: 50 characters – iPhone 6S Plus
About iPod/iPhone
* Only for DDX418BT. Important – iPhone 6S
Make sure all important data has been backed up to – iPhone 6 Plus
Notes on using a USB device avoid losing the data. – iPhone 6
• Avoid using the USB device if it might affect driving We bear no responsibility for any loss of data stored in – iPhone 5S
safety. the devices while using this unit. – iPhone 5C
• When connecting with a USB cable, use a USB 2.0 – iPhone 5
cable. – iPhone 4S
60 ENGLISH
EN_DDX2018ST_KR.indb 60 2017/05/17 9:28

References Troubleshooting
Notes on using an iPod/iPhone What appears to be trouble is not always serious. “Parking off” appears.
• When operating an iPod/iPhone, some operations Check the following points before calling a service → No playback picture is shown when the parking
may not be performed correctly or as intended. In center. brake is not engaged.
this case, visit the following KENWOOD web site: • For operations with external components, refer also “Learning Process Failed” appears.
<www.kenwood.com/cs/ce/> to the instructions supplied with the adapters used → Your steering remote controller is not compatible,
• When you turn on this unit, the iPod/iPhone is for connection (as well as the instructions supplied learning may not be completed. Consult your car
charged through the unit. with the external components). audio dealer for details.
• The text information may not be displayed correctly.
• For some iPod/iPhone models, the performance may General Discs
be abnormal or unstable during operation. In this
No sound comes out of the speakers. Recordable/Rewritable discs cannot be played back.
case, disconnect the iPod/iPhone device, then check
→ Adjust the volume to the optimum level. → Insert a finalized disc.
its condition.
→ Check the cords and connections. → Finalize the discs with the component which you
If the performance is not improved or slow, reset
your iPod/iPhone. No picture is displayed on the screen. used for recording.
→ Turn on the screen. (Page 4) Tracks on the Recordable/Rewritable discs cannot
The unit does not work at all. be skipped.
→ Reset the unit. (Page 4) → Insert a finalized disc.
The remote controller* does not work. → Finalize the discs with the component which you
→ Replace the battery. used for recording.
Playback does not start.
* For DDX395/DDX375BT/DDX350BT/DDX25BT: Purchase optional
→ The format of files is not supported by the unit.
remote controller, KNA-RCDV331.
No picture appears on the external monitor.
“No Signal”/“No Video Signal” appears.
→ Connect the video cord correctly.
→ Start playback on the external component
→ Select the correct input on the external monitor.
connected to the AV-IN input terminal.
→ Check the cords and connections. DivX*/MPEG1/MPEG2/MP3/WMA/WAV/AAC discs
→ Signal input is too weak. cannot be played back.
→ Record the tracks using a compatible application
“Miswiring DC Offset Error”/“Warning DC Offset
on the appropriate discs. (Page 58)
Error” appears.
→ Add appropriate extension codes to the file names.
→ A speaker cord has shorted or it has come into
contact with the car chassis. Wire or insulate the * Only for DDX418BT.
speaker cord as appropriate, then reset the unit. Tracks on the recordable/rewritable discs are not
played back as you have intended them to play.
→ Playback order may differ from the one played back
using other players.
ENGLISH 61
EN_DDX2018ST_KR.indb 61 2017/05/17 9:28

Troubleshooting
“Region Code Error” appears. Sound output only from the Android device. The iPod/iPhone does not turn on or does not
→ You have inserted a DVD Video disc of an incorrect → When <Android Setup> is set to [HAND MODE], work.
region code. Insert a correct region code disc. relaunch the current media player application or → Check the connection.
use another media player application. → Update the firmware version.
USB → Restart the Android device. → Charge the battery.
→ If this does not solve the problem, the connected → Reset the iPod/iPhone.
“Reading” does not disappear from the screen.
Android device is unable to route the audio signal Sound is distorted.
→ Turn the power off and on again.
to unit. → Deactivate the equalizer either on this unit or the
While playing a track, sound is sometimes
Cannot play back when <Android Setup> is set to iPod/iPhone.
interrupted.
[BROWSE MODE]. A lot of noise is generated.
→ The tracks are not properly copied into the USB
→ Make sure KENWOOD Music Play APP is installed on → Turn off (uncheck) “VoiceOver” on the iPod/ iPhone.
device. Copy the tracks again, and try again.
the Android device. For details, visit <http://www.apple.com>.
Tracks are not played back as you have intended → Reconnect the Android device and select the
them to play. No operations are available when playing back a
appropriate control mode.
→ Playback order may differ from the one played back track containing artwork.
→ If this does not solve the problem, the connected
using other players. → Operate the unit after the artwork has loaded.
Android device does not support the Browse
The source does not change to “USB” when you Mode. “Authorization Error” appears.
connect a USB device while listening to another → Check whether the connected iPod/iPhone is
“NO DEVICE” or “READING” keeps flashing.
source or “USB Device Error” appears when you compatible with this unit. (Page 60)
→ Switch off the developer options on the Android
connect a USB device. device.
→ The USB port is drawing more power than the → Reconnect the Android device. Radio
design limit. → If this does not solve the problem, the connected AME automatic presetting does not work.
→ Turn the power off and unplug the USB device. Then, Android device does not support the Browse → Store stations manually. (Page 18)
turn on the power and reattach the USB device. Mode. Static noise while listening to the radio.
→ If the above does not solve the problem, turn
→ Connect the antenna firmly.
the power off and on (or reset the unit) before
iPod/iPhone
replacing with another USB device.
No sound comes out of the speakers. AV-IN
→ Disconnect the iPod/iPhone, then connect it again. (Only for DDX418BT)
Android
→ Select another source, then reselect “iPod”.
Sound cannot be heard during playback. No picture appears on the screen.
→ Reconnect the Android device. → Turn on the video component if it is not on.
→ When <Android Setup> is set to [HAND MODE], → Connect the video component correctly.
launch any media player application on the
Android device and start playback.
62 ENGLISH
EN_DDX2018ST_KR.indb 62 2017/05/17 9:28

Troubleshooting
Pandora*/iHeartRadio*/Spotify “Limited Connectivity” appears. “SXM Check Tuner” appears.
→ The connection with the Pandora application → Make sure the SiriusXM Connect Vehicle Tuner is
The application does not work.
cannot be established. connected to the unit.
→ The application on your iPod touch/iPhone/
Android is not the latest version. Update the “Pandora not available” appears. “SXM Chan Unavailable” appears.
application. → You cannot use the Pandora application from (Appears on the screen for about 5 seconds, then
the area where you are currently trying to access returns to the previous channel):
“Please update Pandora App” appears.
Pandora. → The selected channel is no longer available. Select
→ The Pandora application on your iPod touch/
“Try again later” appears. another channel or continue listening to the
iPhone/Android is not the latest version. Update
→ The Pandora server is under maintenance. previous channel.
the application.
“Station does not exist” appears. “SXM Ch Unsubscribed” appears.
“Please check device.” appears.
→ The selected station has been deleted by another (Appears on the screen for about 5 seconds, then
→ The Pandora application on your iPod touch/
device or has expired. returns to the previous channel)
iPhone/Android has not started up.
→ The selected channel is not part of your current
→ The Pandora application is not installed on the “Cannot create a Station” appears.
subscription plan. Call 1-866-635-2349 to subscribe.
connected device. → You cannot create a station during the read-
→ An error has occurred on the Pandora application. only mode or when network connection is not “SXM Subscription Updated – Press Return to
established. Continue” appears.
“Login Error” appears.
→ Your subscription has been updated. Press the
→ You have not been signed into Pandora. * Only for DDX395/DDX375BT/DDX350BT/DDX25BT. appropriate button to continue.
“No skips remaining” appears.
“SXM Channel Locked” appears.
→ No more songs can be skipped. SiriusXM Satellite Radio → The selected channel has been locked by the
“Failed to save your thumb rating” appears. “SXM No Signal” appears. parental controls. Enter the unlock code when you
→ Thumb-up/down is prohibited. → Make sure the SiriusXM Satellite Radio antenna is are asked.
“No Station” appears. mounted outside the car. Move the car to an area “SXM Incorrect Lock Code” appears.
→ No station is available. with a clear view of the sky. → The selected channel is a mature or parental lock
“No Active Station” appears. “SXM Check Antenna” appears. channel, and locked by the parental lock or user
→ No station is being played. → Check the SiriusXM Satellite Radio antenna lock code. Enter the correct lock code.
connection, and make sure the antenna is firmly
“Station limit reached” appears.
attached to the tuner.
→ The station list is full and no more stations can be
→ Check whether the SiriusXM Satellite Radio antenna
registered.
cable is bent or broken. If it is damaged, replace the
“Failed to save your bookmark” appears. whole antenna unit.
→ The unit has failed to save a bookmark. Try the
operation again.
ENGLISH 63
EN_DDX2018ST_KR.indb 63 2017/05/17 9:28

Troubleshooting Specifications
Bluetooth The unit does not respond when you try to copy
the phone book to the unit.
Monitor section
Phone sound quality is poor.
→ You may have tried to copy the same entries (as Picture Size (W × H) 6.2 inches (diagonal) wide
→ Reduce the distance between the unit and the
stored) to the unit. 137.5 mm × 77.2 mm
Bluetooth mobile phone.
“Connection Error” appears. (5-7/16" × 3-1/16")
→ Move the car to a place where you can get a better
signal reception. → The device is registered but the connection has Display System Transparent TN LCD panel
failed. Connect the registered device. (Page 35) Drive System TFT active matrix system
The sound is interrupted or skipped while using a
Bluetooth audio player. “Please Wait...” appears. Number of Pixels 1 152 000
→ Reduce the distance between the unit and the → The unit is preparing to use the Bluetooth function. (800H × 480V × RGB)
Bluetooth audio player. Disconnect the device If the message does not disappear, turn off and Effective Pixels 99.99%
connected for Bluetooth phone. turn on the unit, then connect the device again (or
reset the unit). Pixel Arrangement RGB striped arrangement
→ Turn off, then turn on the unit.
(When the sound is not yet restored) connect the Back Lighting LED
“No Voice Device” appears.
player again. → The connected mobile phone does not have a
The connected audio player cannot be controlled. voice recognition system. USB interface section
→ Check whether the connected audio player “No Data” appears.
supports AVRCP (Audio/Video Remote Control USB Standard USB 2.0 Full Speed/High
→ No phone book data is contained in the connected
Profile). Speed
Bluetooth phone.
Compatible Device Mass Storage Class
The Bluetooth device does not detect the unit. “Initialize Error” appears.
→ Search from the Bluetooth device again. → The unit has failed to initialize the Bluetooth File System FAT 16/32
The unit does not pair with the Bluetooth device. module. Try the operation again. Maximum Power DC 5 V 1.5 A
→ For devices compatible with Bluetooth 2.1: “Dial Error” appears. Supply Current
Register the device using a PIN code. (Page 35) → Dialing has failed. Try the operation again. D/A Converter 24 bit
→ For devices compatible with Bluetooth 2.0: “Hung Up Error” appears. Audio Decoder MP3/WMA/AAC (.aac/.m4a)/
Enter the same PIN code for both the unit and → The call has not ended yet. Park your car, and use WAV/FLAC
target device. If the PIN code of the device is not the connected mobile phone to end the call. Video Decoder DivX*/MPEG1/MPEG2/JPEG
indicated in its instructions, try “0000” or “1234.”
→ Turn off, then turn on the Bluetooth device. “Pick Up Error” appears.
* Only for DDX418BT.
→ The unit has failed to receive a call.
Echo or noise occurs.
→ Adjust the microphone unit position.
→ Adjust the echo volume or noise reduction volume.
(Page 36)
64 ENGLISH
EN_DDX2018ST_KR.indb 64 2017/05/17 9:28

Specifications
DVD player section Bluetooth section 2 Way X'Over

Tweeter: Frequency (Hz):
D/A Converter 24 bit Technology Bluetooth 3.0
1k/1.6k/2.5k/4k/5k/6.3k/8k/
Audio Decoder Linear PCM/Dolby Audio/ Frequency 2.402 GHz to 2.480 GHz 10k/12.5k
MP3/WMA/WAV/AAC (.m4a) Output Power +4 dBm (MAX), 0 dBm (AVE), Gain (dB):
Video Decoder DivX*/MPEG1/MPEG2/JPEG Power Class 2 –8/–7/–6/–5/–4/–3/–2/–1/0
Wow & Flutter Below Measurable Limit Maximum Line of sight approx. 10 m Front/Rear (HPF): Frequency (Hz):
Frequency Response 96 kHz Sampling: Communication (32.8 ft) Through/30/40/50/60/70/
20 Hz to 22 000 Hz Range 80/90/100/120/150/180/
48 kHz Sampling: Audio Codec SBC/AAC 220/250
20 Hz to 22 000 Hz Profile HFP (Hands Free Profile) 1.6 Slope (dB/Oct.):
44.1 kHz Sampling: A2DP (Advanced Audio −6/−12/−18/−24
20 Hz to 20 000 Hz Distribution Profile) 1.3 Gain (dB):
Total Harmonic 0.010% (1 kHz) AVRCP (Audio/Video Remote –8/–7/–6/–5/–4/–3/–2/–1/0
Distortion Control Profile) 1.5 Subwoofer (LPF): Frequency (Hz):
Signal to Noise Ratio 99 dB (DVD-Video 96 kHz) GAP (Generic Access Profile) 30/40/50/60/70/80/90/100/
PBAP (PhoneBook Access 120/150/180/220/250/
Dynamic Range 99 dB (DVD-Video 96 kHz) Through
Profile) 1.2
Disc Format DVD-Video/VIDEO-CD/CD-DA SDP (Service Discovery Profile) Slope (dB/Oct.):
Sampling Frequency 44.1 kHz/48 kHz/96 kHz SPP (Serial Port Profile) 1.2 −6/−12/−18/−24
Quantifying Bit 16 bit/20 bit/24 bit Phase: Normal/Reverse
Number Gain (dB):
DSP section –8/–7/–6/–5/–4/–3/–2/–1/0
* Only for DDX418BT. Position Front/Rear/Subwoofer Delay:
Equalizer Band: 13 Band
Frequency (Hz) (BAND1–13): 0 ft to 20.0 ft (0.07 ft Step)
62.5/100/160/250/400/630/ Gain: −8 dB to 0 dB
1k/1.6k/2.5k/4k/6.3k/10k/
Subwoofer Level −50 dB to +10 dB
16k
Gain (dB):
–9/−8/−7/−6/−5/−4/−3/−2/
−1/0/1/2/3/4/5/6/7/8/9
Q factor: 1.35/1.5/2.0
ENGLISH 65
EN_DDX2018ST_KR.indb 65 2017/05/17 9:28

Specifications
FM tuner section Video section General

Frequency Range DDX395/DDX375BT/ Color System of NTSC/PAL Operating Voltage 14.4 V
DDX350BT/DDX25BT: External Video Input (10.5 V to 16 V allowable)
87.9 MHz to 107.9 MHz External Video Input 1 Vp-p/75 Ω Maximum Current 10 A
(200 kHz) Level (mini jack)* Consumption
DDX418BT: External Audio Max 2 V/25 kΩ Installation DDX395:
87.5 MHz to 108.0 MHz Input Level (mini Dimensions With sleeve:
(50 kHz) jack)* (W × H × D) 182 mm × 111 mm
Usable Sensitivity 7.2 dBf (0.63 μV/75 Ω) Video Input Level for 1 Vp-p/75 Ω × 160 mm
(S/N: 30 dB) Rear Camera (RCA (7-3/16" × 4-3/8" × 6-5/16")
jack) Without sleeve:
Quieting Sensitivity 15.2 dBf (1.58 μV/75 Ω)
178 mm × 100 mm ×
(S/N: 50 dB) Video Output Level 1 Vp-p/75 Ω
162 mm
Frequency Response 30 Hz to 15 kHz (RCA jack)
(7" × 3-15/16" × 6-3/8")
(±3.0 dB) DDX375BT/DDX350BT/
* Only for DDX418BT.
Signal to Noise Ratio 68 dB (MONO) DDX25BT/DDX418BT:
Selectivity (±400 kHz) > 80 dB Audio section 178 mm × 100 mm ×
Stereo Separation 40 dB (1 kHz) 162 mm
Maximum Power 50 W × 4 (7" × 3-15/16" × 6-3/8")
(Front & Rear)
Operational –10°C to +60°C
AM tuner section Full Bandwidth 22 W × 4 (at less than 1% Temperature Range
Power (Front & Rear) THD)
Frequency Range 530 kHz to 1 700 kHz (10 kHz) Weight (Main Unit) DDX395: 2.0 kg (4.4 lbs)
Preout Level DDX395: (including trim plate and
Usable Sensitivity 29 dBμ 5 V/10 kΩ sleeve)
DDX375BT: DDX375BT/DDX350BT/
4 V/10 kΩ DDX25BT: 1.7 kg (3.8 lbs)
DDX350BT/DDX25BT/ DDX418BT: 1.8 (4.0 lbs)
DDX418BT: (including trim plate)
2.5 V/10 kΩ
Preout Impedance ≤ 600 Ω
Design and specifications are subject to change
Speaker Impedance 4 Ω to 8 Ω without notice.
66 ENGLISH
EN_DDX2018ST_KR.indb 66 2017/05/17 9:28

Specifications
• THIS PRODUCT IS LICENSED UNDER THE AVC PATENT and/or other materials provided with the
Trademarks and licenses
PORTFOLIO LICENSE FOR THE PERSONAL USE OF A distribution.
• Dolby, Dolby Audio and the double-D symbol are CONSUMER OR OTHER USES IN WHICH IT DOES NOT – Neither the name of the Xiph.org Foundation
trademarks of Dolby Laboratories. RECEIVE REMUNERATION TO nor the names of its contributors may be used to
• “DVD Logo” is a trademark of DVD Format/Logo (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC endorse or promote products derived from this
Licensing Corporation registered in the US, Japan STANDARD ("AVC VIDEO") AND/OR (ii) DECODE software without specific prior written permission.
and other countries. AVC VIDEO THAT WAS ENCODED BY A CONSUMER THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
• The “AAC” logo is a trademark of Dolby Laboratories. ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
• Microsoft and Windows Media are either registered OBTAINED FROM A VIDEO PROVIDER LICENSED TO EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
trademarks or trademarks of Microsoft Corporation in PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
the United States and/or other countries. SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL MERCHANTABILITY AND FITNESS FOR A PARTICULAR
• “Made for iPod,” and “Made for iPhone” mean that an INFORMATION MAY BE OBTAINED FROM MPEG LA, PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
electronic accessory has been designed to connect L.L.C. SEE HTTP://WWW.MPEGLA.COM THE FOUNDATION OR CONTRIBUTORS BE LIABLE
specifically to iPod, or iPhone, respectively, and • Sirius, XM and all related marks and logos are FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
has been certified by the developer to meet Apple trademarks of Sirius XM Radio Inc. All rights reserved. EXEMPLARY, OR CONSEQUENTIAL DAMAGES
performance standards. • Pandora, the Pandora logo, and the Pandora trade (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
Apple is not responsible for the operation of this dress are trademarks or registered trademarks of OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
device or its compliance with safety and regulatory Pandora Media, Inc., used with permission. DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
standards. Please note that the use of this accessory • SPOTIFY and the Spotify logo are among the HOWEVER CAUSED AND ON ANY THEORY OF
with iPod, or iPhone may affect wireless performance. registered trademarks of Spotify AB. LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
iPhone, iPod, iPod classic, iPod nano, and iPod touch • iHeartRadio® and iHeartAuto™ are trademarks owned OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
are trademarks of Apple Inc., registered in the U.S. by iHeartMedia, Inc. All uses are authorized under ARISING IN ANY WAY OUT OF THE USE OF THIS
and other countries. license. SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
• Lightning is a trademark of Apple Inc. • libFLAC SUCH DAMAGE.
• This item incorporates copy protection technology Copyright (C) 2000-2009 Josh Coalson • DIVX
that is protected by U.S. patents and other Copyright (C) 2011-2013 Xiph.Org Foundation – This DivX Certified® device has passed rigorous
intellectual property rights of Rovi Corporation. Redistribution and use in source and binary forms, testing to ensure it plays DivX® video.
Reverse engineering and disassembly are prohibited. with or without modification, are permitted provided To play purchased DivX movies, first register your
• Font for this product is designed by Ricoh. that the following conditions are met: device at vod.divx.com. Find your registration
• Android is a trademark of Google Inc. – Redistributions of source code must retain the code in the DivX VOD section of your device setup
• The Bluetooth® word mark and logos are registered above copyright notice, this list of conditions and menu. (Page 47)
trademarks owned by Bluetooth SIG, Inc. and any the following disclaimer. – DivX Certified® to play DivX® video, including
use of such marks by JVC KENWOOD Corporation is – Redistributions in binary form must reproduce the premium content.
under license. Other trademarks and trade names are above copyright notice, this list of conditions and – DivX®, DivX Certified® and associated logos are
those of their respective owners. the following disclaimer in the documentation trademarks of DivX, LLC and are used under license.
ENGLISH 67
04_DDX_2018ST_KR_Body02.indd 67 9/5/2017 5:27:36 PM

For updated information (the latest Instruction Manual, system updates, new functions, etc.),
please visit the following website:
<www.kenwood.com/cs/ce/>
EN_DDX2018ST_KR.indb 1 2017/05/17 9:28

DDX395 DDX375BT DDX350BT Ddx25Bt DDX418BT: Instruction Manual

Uploaded by

Copyright:

Available Formats

DDX395 DDX375BT DDX350BT Ddx25Bt DDX418BT: Instruction Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DDX395 DDX375BT DDX350BT Ddx25Bt DDX418BT: Instruction Manual

Uploaded by

Copyright:

Available Formats

What safety precautions should be taken while operating the device?

What safety precautions should be taken while operating the device?

What should be done before operating the device after parking for a long time?

What should be done before operating the device after parking for a long time?

ENGLISH

MONITOR WITH DVD RECEIVER

DDX350BT (Region 1 – DVD Region Code 1 Area)

Take the time to read through this instruction manual.

01_DDX_2018ST_KR_COVER.indd 1 9/5/2017 5:25:52 PM

EN_DDX2018ST_KR.indb i 2017/05/17 9:27

EN_DDX2018ST_KR.indb ii 2017/05/17 9:27

EN_DDX2018ST_KR.indb 2 2017/05/17 9:27

1 Reset button/Power indicator/Security indicator 1 Reset button/Power indicator/Security indicator

EN_DDX2018ST_KR.indb 3 2017/05/17 9:27

Turning on the power

Turning off the power

On the monitor panel

EN_DDX2018ST_KR.indb 4 2017/05/17 9:27

EN_DDX2018ST_KR.indb 5 2017/05/17 9:27

2 Activate the security function. Reset

EN_DDX2018ST_KR.indb 6 2017/05/17 9:27

[AV-IN]*1 Switches to an external component

EN_DDX2018ST_KR.indb 7 2017/05/17 9:27

EN_DDX2018ST_KR.indb 8 2017/05/17 9:27

EN_DDX2018ST_KR.indb 9 2017/05/17 9:27

EN_DDX2018ST_KR.indb 10 2017/05/17 9:27

Screen Ratio 16:9

EN_DDX2018ST_KR.indb 11 2017/05/17 9:27

<Auto>: For “DISC” source and

EN_DDX2018ST_KR.indb 12 2017/05/17 9:27

EN_DDX2018ST_KR.indb 13 2017/05/17 9:27

File type Audio

EN_DDX2018ST_KR.indb 14 2017/05/17 9:27

Installing KENWOOD Music Play Selecting a track from the menu

EN_DDX2018ST_KR.indb 15 2017/05/17 9:27

Artwork ON OFF Playback operations

EN_DDX2018ST_KR.indb 16 2017/05/17 9:27

EN_DDX2018ST_KR.indb 17 2017/05/17 9:27

To hide the window: Touch [ ].

E.g. Radio source control screen for DDX395

The station selected in step 1 is stored into the

EN_DDX2018ST_KR.indb 18 2017/05/17 9:27

EN_DDX2018ST_KR.indb 19 2017/05/17 9:27

[ ] (Hold) Registers the current song to

On the source control screen, touch as follows: 105Ch

• SEEK2: Skips to another preset 115Ch

[SCAN] Starts TuneScan™. 2 Select a category (1), and then select a

All Channels 100Ch Channel Name

EN_DDX2018ST_KR.indb 20 2017/05/17 9:27

Selecting a preset channel Replaying content [IW] Starts/pauses playback.

EN_DDX2018ST_KR.indb 21 2017/05/17 9:27

TuneScan™ (Hold) League3 Team3

The unit starts scanning.

EN_DDX2018ST_KR.indb 22 2017/05/17 9:27

SiriusXM Reset Reset

EN_DDX2018ST_KR.indb 23 2017/05/17 9:27

2 Select the desired mode for <Parental

• To clear the last entry, touch [Clear].

EN_DDX2018ST_KR.indb 24 2017/05/17 9:27