B engine

LU Lubricant system

LU

Prepared by .................................................. .................. Two ·Time for replacement .................................................. ........ Five

Special tools .................................................. ... ...... 2 And removal, installation ................................... . . . . . Five
engine oil ................................................ ...... 3 Oil pump .................................................. .. ..... 7 C

·inspection .................................................. ................ Three And removal, installation ................................... ..... 7

·Time for replacement .................................................. ... . . . . . .Four Disassembly, assembly .......................................... ..... 7
· Replacement procedure .................................................. ... . . . . . .Four Service data ................................................ ..... 9
oil filter .................................................. Five · Reference value, limit value .......................................... ..... 9
D
With-tightening torque ................................................. ..... 9

KA

LU - 1
 Prepared by

Prepared by PFP: 00002

Special tool JBS00GFV

name Use

Oil filter wrench

Oil filter removal
KV10115801

ZZA1085D

LU - 2
 engine oil

engine oil PFP: KLA92

inspection JBS00GFW

Amount of oil and dirt

• Oil amount of inspection is carried out before starting the engine in a horizontal location. After the stop if you start Ten Elapsed performed after more minute.

• L Level and H Level check whether there is oil level between, if the oil amount of the excess and deficiency

to adjust.
LU

• Clouded in engine oil, check whether or not there is significant contamination, if there is an abnormality,
replace the engine oil.

• Because if you are cloudy there is a high possibility of the cooling water contamination, the cause place to

exchange the repair after the engine oil. C

LCA0064D

D
Oil leak
Following the various parts from such inspections if there is leakage of engine oil.

• Oil pan

• Oil pan drain plug E

• Oil pressure switch

• oil filter

• CVTC Cover and CVTC valve

• Joint surface of the cylinder block and the cylinder head F

• Joint surface of the cylinder head and the rocker cover

• Joint surface of the front timing chain case and the rear timing chain case

• Joint surface of the rear timing chain case and the engine
G
• Front oil seal

• Rear oil seal

Hydraulic inspection

H
1. To check the amount of oil.

2. Remove the under cover.

3. Remove the alternator bracket. " Charging system " (SC-8 Page
Di ) To see. I

Four. Remove the oil pressure switch, connecting the oil pressure gauge.

Five. After the engine warm-up, the hydraulic pressure or to check there in accordance with the rotation.

Reference: And the oil temperature is low pressure is high. J

KBIA1601J

KA

Engine oil pressure (oil temperature 80 ℃ at the time)

( MPa { kg / cm 2 })

Engine RPM( rpm ) Idle 2000 6000

Engine oil pressure 0.1 { 1.0 }that's all 0.29 { 3.0 }that's all 0.39 { 4.0 }that's all L

6. The oil pressure switch after inspection mounted in the following manner.

LU - 3
 engine oil

a. Get rid of the old liquid gasket adhering to the oil pressure switch side and the engine side.

b. Liquid gasket on the threaded portion (Three Bond 1201 Tighten equivalent) by applying a.

Tightening torque : 12.3 ~ 17.2 N - m { 1.3 ~ 1.7 kg - m }

Time for replacement JBS00GFX

• To exchange the travel distance or period of below.

Recommended engine oil

API ; SL Class, SAE ; 5W-30 while using it : 15,000km Or One Per year (whichever comes first)

Caution : Engine oil is the quality ( API ) The use of more than that. viscosity( SAE ) Was used as something other than the above

When, it may affect the engine performance.

Replacement Procedure JBS00GFY

Caution : That when the engine oil is hot to be careful not to burn.

1. The engine to warm up.

2. Stop the engine, Ten Minute to stand for at least.

3. Remove the oil filler cap, remove the drain plug.

Four. Extracting the engine oil.

Five. Installing a drain plug.

• Washer of the drain plug is replaced with a new one.

• Washer - is mounted so as to be in the direction of the figure.

Tightening torque: 29.4 ~ 39.2 N - m { 3.0 ~ 4.0 kg - m }

EMA0427D

6. To inject a new engine oil. " Time for replacement"( LU-4 page ) To see.

Amount of oil (liters)

H Level (oil pan capacity) : 4.8

L Level (same as above) when the : 4.0
replenishment rate exchange only oil :about 4.5
Oil filter, when the replenishing amount reference oil exchange Total :about 4.7
capacity (factory first filling) :about 5.4

7. After confirming that there is no leakage of engine oil, amount of oil at a level gauge to check whether there within the reference. " inspection"( LU-3 Page

Di ) To see.

LU - 4
 oil filter

oil filter PFP: 15208

Time for replacement JBS00GFZ

To exchange the travel distance or period of below.

Time for replacement : 15,000km Or One Per year (whichever comes first)

Removal, installation JBS00GG0 LU

removal

1. Opening the oil filter desorption for the cover of the under cover.

KBIA1602J

E
2. The oil filter using an oil filter wrench (special tool)
Remove.

Caution : • At the time of removal, since the engine oil leaks rag
Prepare to be and the like.
F
• Oil catcher, under cover, other engine oil adhering to the vehicle side
parts and engine and the like is completely Wipe take it.

G
KBIA1603J

attachment

1. The foreign matter attached to the oil filter mounting surface completely remove.
H
2. Oil seal part the entire periphery to the engine oil of the new oil filter
It is coated.

J
SMA010

KA

LU - 5
 oil filter

3. Oil Screw filter by hand, or hit the engine side mounting surface
Et al. 2/3 Tighten rotation. Reference: The tightening torque 14.7 ~ 20.5N - m { 1.5 ~ 2.1kg - m } It considers to be

made.

KBIA2064J

Inspection after mounting

1. To check the engine oil level. " engine oil"( LU-3 page ) To see.

2. Start the engine, to ensure that there is no leakage of engine oil.

3. Stop the engine, check the engine oil level again. " engine oil"( LU-3 page ) To see.

LU - 6
 Oil pump

Oil pump PFP: 15010

Removal, installation JBS00GG3

LU

KBIA1632J

E
removal

1. Oil pan (upper, lower) and remove the oil strainer. " Oil pan, oil strainer "( EM-23
page ) To see.

F
2. Front timing chain case, remove the timing chain (primary). " Timing chain "
(EM-44 page ) To see.

3. Oil pump ASSY A remove.

G
attachment

1. Be aware of the following installed in reverse the removal procedure.

• Mounted on the crank shaft flats width to match the orientation of the inner rotor dihedral width.

H
Disassembly, assembly JBS00GG4

Disassembly

1. Remove the oil pump cover.

I
2. From the oil pump housing, the outer rotor, remove the inner rotor.

3. Remove the regulator plug, remove the spring, the regulator valve.

Inspection after decomposition

J
Oil pump each part of the clearance
• To measure the various parts of the clearance using a thickness gauge. Outer rotor

and oil pump housing of clearance (FIG.

One )
KA

Reference value : 0.114 ~ 0.260 mm

Outer rotor and the inner rotor tip clearance (FIG.

Two )
L

Reference value : 0.180 mm Less than

LCQ0021D

LU - 7
 Oil pump

• To measure the various parts of the clearance using a straight gauge and thickness gauge.

Of side clear run (Figure of the inner rotor and oil pump housing Three )

Reference value : 0.030 ~ 0.070 mm

Side clear run scan of the outer rotor and oil pump housing (FIG. Four )

Reference value : 0.050 ~ 0.110 mm LCQ0022D

Spigot part clearance of the inner rotor and oil pump housing

• Of the oil pump housing in low inner diameter (Figure using the inside micrometer Five
) Is measured.

• Using a micrometer, inner rotor spigot outer diameter (FIG. Six ) Is measured.

(Clearance) = (oil pump housing spigot inner diameter) - (inner rotor spigot part
contour)

Reference value : 0.045 ~ 0.091 mm LCQ0026D

• If an off-the reference value described above, the oil pump ASSY To exchange.

Of the regulator valve clearance

• From the valve hole inner diameter by subtracting the regulator valve outside diameter to
calculate the clearance.

(Clearance) = (valve hole inside diameter) - (valve outside diameter)

Reference value : 0.040 ~ 0.097 mm

Caution : • The engine oil is applied to the regulator valve, valve

There ensuring that move smoothly.

• If an off-standard value, the oil pump ASSY To exchange.

LCQ0023D

assembly
Be aware of the following, assembled in the reverse order of disassembly.

• Mount toward the groove of the inner rotor to the cover side.

LCL0011D

LU - 8
 Service data

Service data PFP: 00030

Reference value, limit value JBS00J8S

Engine oil exchange time ( API SL At the time or 15,000km Or One Per year
higher grade of oil used) (whichever comes first)

H Level (oil pan capacity) 4.8

L Level (same as above) 4.0 LU

Engine oil level (liters) When the replenishment rate exchange only oil about 4.5

About oil and during filter replacement replenishment amount 4.7

Total capacity (factory first filling) about 5.4

15,000km Or One Per year

C
Oil filter change time
(whichever comes first)

Tightening torque JBS00J8T

unit: N - m {kg - m}
D
Oil pan drain plug 29.4 ~ 39.2 { 3.0 ~ 4.0 }

oil filter After sitting 2/3 rotation( 14.7 ~ 20.5 { 1.5 ~ 2.1 } Or equivalent)

KA

LU - 9
Service data

LU - 10